Panasonic KX-HNS101 Instrucciones de operación
- Tipo
- Instrucciones de operación
Installation Guide
Home Network System
Window/Door Sensor
Model No. KX-HNS101
Thank you for purchasing a Panasonic product.
This document explains how to install the window/door sensor
properly.
For details about how to use the system, refer to the User’s Guide
(page 17).
Please read this document before using the unit and save it for future
reference.
For assistance, please contact us at 1-800-272-7033 or visit our Web
site: http://shop.panasonic.com/support for customers in the U.S.A.
Please register your product: http://shop.panasonic.com/support
Printed in China
HNS101_(en_en)_0616_ver.130.pdf 1 2015/06/16 22:24:10
Introduction
Accessory information ...............3
Important Information
About this system ......................4
For your safety ...........................
4
Important safety instructions ......5
For best performance ................5
Other information .......................6
Setup
Part names and functions ..........8
LED indicator .............................8
Setup overview ..........................8
Inserting the battery ...................9
Registering the window/door
sensor ........................................9
Changing the sensor type ........10
Wireless communication
range .......................................10
Temporary placement ..............11
Installation ...............................14
Appendix
Testing the window/door
sensor ......................................17
Features available when using the
[Home Network] app ................17
Accessing the User’s Guide ....17
Specifications ..........................18
FCC and other information ......19
Customer services ...................20
Limited Warranty (ONLY FOR
U.S.A.) .....................................21
2
Table of Contents
HNS101_(en_en)_0616_ver.130.pdf 2 2015/06/16 22:24:10
Accessory information
Supplied accessories
No. Accessory item/Part number Quantity
A
Battery
*
1
1
B
Mounting screws (20 mm (25/32 inches))
*
2
/XMM38+20VW
4
C
Mounting double-sided tapes
*
3
3
*1 When replacing the battery, see “Power source” of “Specifications”, page 18
f
or battery information.
*2 2 screws for the sensor unit and 2 screws for the magnet unit
*3 2 pieces of tape for the sensor unit: PNHS1620Z
1 piece of tape for the magnet unit: PNHS1621Z
A
B C
Other information
R D
esign and specifications are subject to change without notice.
R The illustrations in these instructions may vary slightly from the actual product.
Trademarks
R i
Phone and iPad are registered trademarks of Apple Inc.
R Android is a trademark of Google Inc.
R Microsoft, Windows, and Internet Explorer are either registered trademarks or
trademarks of Microsoft Corporation in the United States and/or other countries.
R All other trademarks identified herein are the property of their respective owners.
For assistance, please visit http://shop.panasonic.com/support
3
Introduction
HNS101_(en_en)_0616_ver.130.pdf 3 2015/06/16 22:24:10
About this system
R This system is an auxiliary system; it
is not designed to provide complete
protection from property loss.
Panasonic will not be held
responsible in the event that
property loss occurs while this
system is in operation.
R The system’s wireless features are
subject to interference, therefore
functionality in all situations cannot
be guaranteed. Panasonic will not
be held responsible for injury or
damage to property that occurs in
the event of wireless communication
error or failure.
For your safety
T
o prevent severe injury and loss of life/
property, read this section carefully
before using the product to ensure
proper and safe operation of your
product.
WARNING
Power connection
R U
se only the power source marked
on the product.
R Do not connect non-specified
devices.
Installation
R T
o prevent the risk of fire or
electrical shock, do not expose the
product to rain or any type of
moisture.
R Do not place or use this product
near automatically controlled
devices such as automatic doors
a
nd fire alarms. Radio waves
emitted from this product may cause
such devices to malfunction
resulting in an accident.
R Keep small parts (magnet unit,
magnet unit cover, screws, etc.) out
of the reach of children. There is a
risk of swallowing. In the event they
are swallowed, seek medical advice
immediately.
Operating safeguards
R D
o not disassemble the product.
Medical
R C
onsult the manufacturer of any
personal medical devices, such as
pacemakers or hearing aids, to
determine if they are adequately
shielded from external RF (radio
frequency) energy. DECT features
operate between 1.92 GHz and
1.93 GHz with a peak transmission
power of 115 mW.
R Do not use the product in health
care facilities if any regulations
posted in the area instruct you not to
do so. Hospitals or health care
facilities may be using equipment
that could be sensitive to external
RF energy.
CR Lithium battery
R D
o not recharge, disassemble,
remodel, heat or throw it into fire.
R Do not touch the terminals
and
with metal objects.
R R
isk of explosion if battery is
replaced by an incorrect type.
Dispose of used battery according to
local regulations.
4
For a
ssistance, please visit http://shop.panasonic.com/support
Important Information
HNS101_(en_en)_0616_ver.130.pdf 4 2015/06/16 22:24:10
R I
f any electrolyte should come into
contact with your hands or clothes,
wash it off thoroughly with water.
R If any electrolyte should come into
contact with your eyes, never rub
your eyes. Rinse your eyes
thoroughly with water, and then
consult a doctor.
CAUTION
General information
R D
o not place magnetic cards or
similar objects near the sensor unit
and magnet unit. Magnetic data on
the cards, etc. may be deleted.
CR Lithium battery
R U
se only the battery noted on
page 3.
R Insert the battery correctly.
R Do not leave the battery in an
automobile exposed to direct
sunlight for a long period of time with
the doors and windows closed.
R Remove the battery if you do not
use the product for a long period of
time. Keep it in a cool, dark area.
R Do not replace a battery with wet
hands.
R Keep out of the reach of small
children. There is a risk of
swallowing. If the battery is
swallowed, seek medical attention
immediately.
R Remove the battery if it becomes
unusable. There is a risk of leakage,
overheating, and rupture. Do not
attempt to use a battery if it is
leaking.
R Exercise care when handling the
batteries. Do not allow conductive
materials such as rings, bracelets, or
keys to touch the batteries,
otherwise a short circuit may cause
t
he batteries and/or the conductive
material to overheat and cause
burns.
Important safety
i
nstructions
When using your product, basic safety
precautions should always be followed
to reduce the risk of fire, electric shock,
and injury to persons, including the
following:
1. Do not use this product near water
for example, near a bathtub,
washbowl, kitchen sink, or laundry
tub, in a wet basement or near a
swimming pool.
2. Use only the batteries indicated in
this document. Do not dispose of
batteries in a fire. They may
explode. Check with local codes for
possible special disposal
instructions.
SAVE THESE INSTRUCTIONS
For b
est performance
Hub location/avoiding noise
T
he hub and other compatible
Panasonic devices use radio waves to
communicate with each other.
R For maximum coverage and
noise-free communications, place
your hub:
– at a convenient, high, and central
location with no obstructions
between the product and hub in
an indoor environment.
For a
ssistance, please visit http://shop.panasonic.com/support
5
Important Information
HNS101_(en_en)_0616_ver.130.pdf 5 2015/06/16 22:24:10
– away from electronic appliances
s
uch as TVs, radios, personal
computers, wireless devices, or
other phones.
– facing away from radio frequency
transmitters, such as external
antennas of mobile phone cell
stations. (Avoid putting the hub
on a bay window or near a
window.)
R If the reception for a hub location is
not satisfactory, move the hub to
another location for better reception.
Environment
R K
eep the product away from
electrical noise generating devices,
such as fluorescent lamps and
motors.
R The product should be kept free
from excessive smoke, dust, high
temperature, and vibration.
R The product should not be exposed
to direct sunlight.
R Do not place heavy objects on top of
the product.
R The product should be kept away
from heat sources such as heaters,
kitchen stoves, etc. It should not be
placed in rooms where the
temperature is less than -10 °C
(14 °F) or greater than 40 °C
(104 °F). Damp basements should
also be avoided.
R Operating the product near electrical
appliances may cause interference.
Move away from the electrical
appliances.
Other information
C
AUTION: Risk of explosion if battery
is replaced by an incorrect type.
Dispose of used batteries according to
t
he instructions.
Routine care
R W
ipe the outer surface of the
product with a soft moist cloth.
R Do not use benzine, thinner, or any
abrasive powder.
Information on Disposal in other
C
ountries outside the European
Union
These symbols are only valid in the
E
uropean Union. If you wish to discard
these items, please contact your local
authorities or dealer and ask for the
correct method of disposal.
Note for the battery removal
p
rocedure
Refer to “Inserting the battery” on
page 9.
6
For assistance, please visit http://shop.panasonic.com/support
Important Information
HNS101_(en_en)_0616_ver.130.pdf 6 2015/06/16 22:24:10
Notice
For a
ssistance, please visit http://shop.panasonic.com/support
7
Important Information
HNS101_(en_en)_0616_ver.130.pdf 7 2015/06/16 22:24:10
Part names and
functions
n
Sensor unit n Magnet unit
D
B
C
A
E
E
Sensor unit cover
M N
U
sed to confirm the status of the
sensor or register the sensor to
the hub.
LED indicator
Magnet unit cover
“ ” marks
Used to align the sensor and the
magnet unit when installing them
(page 11).
LED indicator
You can press M N
and check the
LED indicator to confirm the sensor’s
status.
Indicator Status
Green, lit Window/door is closed
Red, lit Window/door is open
Red,
b
linking
Sensor is out of range
of the hub
Green,
b
linking
slowly
Registration mode
(You pressed and held
M
N)
Off No battery power
Note:
R T
he LED indicator does not indicate
sensor status if the sensor has not
been registered (page 9).
Setup overview
1 I
nitial setup
Make sure you can access the
system using your mobile device.
For details, refer to the System
Setup Guide included with your
hub.
2 Insert the battery
The window/door sensor is battery
powered.
3 Registration
Required only if the window/door
sensor was purchased separately
(i.e., not as part of a bundle).
4 Confirm the installation area
Read the information in this
document to confirm that the
8
For a
ssistance, please visit http://shop.panasonic.com/support
Setup
HNS101_(en_en)_0616_ver.130.pdf 8 2015/06/16 22:24:10
desired installation area is suitable
t
o proper operation.
5 Temporary placement
Temporarily place the window/
door sensor in the desired location
and confirm that it operates
properly (page 11).
6 Installation
Install the window/door sensor on
the same position where proper
operation was confirmed
(page 14).
Inserting the battery
R U
SE ONLY a CR2 Lithium battery.
R Confirm the polarities (
, ).
1 Remove the sensor unit cover.
R Lift from the indented area (A)
and open the sensor unit cover
(B).
1
2
2 I
nsert the battery.
3 A
ttach the sensor unit cover.
Registering the
w
indow/door sensor
This procedure is not required for
d
evices that were included as part of
a bundle.
Before you can use the window/door
s
ensor, it must be registered to the hub.
If you purchased devices separately
(i.e., not as part of a bundle), you must
register each device to the hub.
You can register each device by using
the registration buttons or the [Home
Network] app.
Using registration buttons
1 H
ub:
Press and hold M
OTHER
D
EVICEN until the LED indicator
blinks slowly in green.
2 Window/door sensor:
Remove the sensor unit cover and
press and hold M
N
until the
LED indicator blinks slowly in
green (page 8).
For a
ssistance, please visit http://shop.panasonic.com/support
9
Setup
HNS101_(en_en)_0616_ver.130.pdf 9 2015/06/16 22:24:10
R W
hen registration is complete,
the hub sounds one long beep.
Note:
R To cancel without registering the
sensor, press M
N
on the hub and
on the sensor again.
R If registration fails, the hub sounds
several short beeps.
Using the app
W
hen you register the window/door
sensor by using the [Home Network]
app, you can assign a name to your
devices and group them by location.
For more information, refer to the
User’s Guide (page 17).
Changing the sensor
t
ype
You can select whether a window/door
sensor functions as a window sensor or
as a door sensor. For more
information, refer to the User’s Guide
(page 17).
Wireless
communication
range
The wireless communication range of
each device in the system from the hub
is approximately 50 m (160 feet)
indoors and approximately 300 m
(1,000 feet) outdoors. Wireless
communication may be unreliable
when the following obstacles are
located between the hub and other
devices.
R Metal doors or screens
R Walls containing aluminum-sheet
insulation
R Walls made of concrete or
corrugated iron
R Double-pane glass windows
R Multiple walls
R When using each device on
separate floors or in different
buildings
Note:
R You can check the window/door
sensor’s communication status by
pressing M N.
If the LED indicator
is lit in green or red, the sensor is
communicating properly with the
hub. If the LED indicator blinks in
red, it is out of range of the hub.
10
For a
ssistance, please visit http://shop.panasonic.com/support
Setup
HNS101_(en_en)_0616_ver.130.pdf 10 2015/06/16 22:24:10
Temporary placement
Before installing the window/door sensor, temporarily place it in the desired
location and confirm that it operates properly by pressing M N.
I
mportant:
R Attach the sensor unit to the window frame or door frame, and attach the
magnet unit to the window or door.
R The window/door sensor will not operate properly if the “
” marks are too far
apart or are not pointing toward each other.
R Attach both units so that the “ ” marks point toward each other and are within
2
5.4 mm (1 inch) of each other.
Confirming proper operation
A
fter temporarily placing the window/door sensor in the desired location, press
M
N
while the window or door is closed. The window/door sensor’s LED indicator
lights as follows.
Indicator Status
Green, lit The installation position is correct.
Red, lit
The “
” marks on the sensor unit and the magnet unit
a
re too far from each other. Re-attach the sensor unit
and the magnet unit so that they point directly at each
other and are no more than 25.4 mm (1 inch) apart.
Red, blinking The sensor unit is out of range of the hub. Refer to the
i
nformation on page 10.
Note:
R D
epending on the condition and material of the surface where the sensor unit
and magnet unit are installed, the LED indicator may light in red even if the “
”
marks point directly at each other and are no more than 25.4 mm (1 inch) apart.
For a
ssistance, please visit http://shop.panasonic.com/support
11
Setup
HNS101_(en_en)_0616_ver.130.pdf 11 2015/06/16 22:24:10
Example 1: Installed on the left side of a window
Correct
1
A
B
Green
1
“ ” marks point directly at each other and are within 25.4 mm (1 inch) of each
o
ther.
Result: When you press M
N
(A), the LED indicator lights in green (B).
Incorrect
2
3
4
A
B
Red
2
“ ” marks are aligned but units are too far apart.
3
“ ” marks are aligned but window frame is too thick; units are too far apart.
4
“ ” marks are not aligned. Magnet unit is too high.
R
esult: When you press M
N
(A), the LED indicator lights in red (B).
12
For a
ssistance, please visit http://shop.panasonic.com/support
Setup
HNS101_(en_en)_0616_ver.130.pdf 12 2015/06/16 22:24:11
Example 2: Installed on the right side of a window
Correct
1
A
B
Green
1
“ ” marks point directly at each other and are within 25.4 mm (1 inch) of each
o
ther.
Result: When you press M
N
(A), the LED indicator lights in green (B).
Incorrect
2
3
4
A
B
Red
2
“ ” marks are aligned but units are too far apart.
3
“ ” marks are aligned but window frame is too thick; units are too far apart.
4
“ ” marks are not aligned. Magnet unit is too high.
R
esult: When you press M
N
(A), the LED indicator lights in red (B).
For a
ssistance, please visit http://shop.panasonic.com/support
13
Setup
HNS101_(en_en)_0616_ver.130.pdf 13 2015/06/16 22:24:11
Installation
Install the window/door sensor in the same position where proper operation was
confirmed (page 11). You can install the window/door sensor using screws or
double-sided tape, depending on your preference or the material of the installation
area.
Note:
R When installing, make sure the battery is inserted properly and the sensor unit
cover is completely closed.
R Use screws when installing on a wooden surface. Do not use double-sided tape.
Securing with screws
1 R
emove the covers from each unit.
R Lift from the indented area (A) and open the sensor unit cover (B).
1
2
1
2
14
For a
ssistance, please visit http://shop.panasonic.com/support
Setup
HNS101_(en_en)_0616_ver.130.pdf 14 2015/06/16 22:24:11
2 S
ensor unit:
Attach the sensor unit.
1
Screws
2
86.2 mm (3 25/64 inches)
M
agnet unit:
Attach the magnet unit.
3
Screws
4
24.4 mm (31/32 inches)
2
4
1
1
3
3
5
3 A
ttach the covers.
Important:
R
5
Align the “ ” marks on the sensor unit and the magnet unit so that they
p
oint directly at each other and are no more than 25.4 mm (1 inch) apart.
For a
ssistance, please visit http://shop.panasonic.com/support
15
Setup
HNS101_(en_en)_0616_ver.130.pdf 15 2015/06/16 22:24:11
Securing with double-sided tape
Note:
R Make sure the surfaces of the sensor unit, magnet unit, and the installation area
are clean and dry before applying double-sided tape.
1 Check that the sensor unit cover and magnet unit cover are attached.
2 Affix double-sided tape to the sensor unit and magnet unit.
R Make sure the tape covers the screw holes on the back of each unit.
5
3 I
nstall the sensor unit and magnet unit.
R Press firmly on each unit to ensure solid adhesion to the installation surface.
Important:
R
5
Align the “ ” marks on the sensor unit and the magnet unit so that they
p
oint directly at each other and are no more than 25.4 mm (1 inch) apart.
Removing when secured with double-sided tape
1 Tie a piece of thread to two sticks, screwdrivers, etc.
2 Pull the thread tight and use it to cut the double-sided tape, and then remove
any excess tape.
1
Excess tape
1
16
For a
ssistance, please visit http://shop.panasonic.com/support
Setup
HNS101_(en_en)_0616_ver.130.pdf 16 2015/06/16 22:24:11
Testing the window/
door sensor
You can check the window/door
sensor’s LED indicator and test the
performance of the window/door
sensor.
1 Remove the sensor unit cover.
2 Press M N
on the sensor unit.
3 Open and close the window or
door several times.
R Make sure that the LED
indicator lights in green when
you close the window or door.
4 Press M
N
again.
Note:
R If the LED indicator lights in red
when the window or door is closed,
the window/door sensor is not
installed properly. Re-evaluate the
position of the sensor unit and
magnet unit (page 11).
Features available
w
hen using the
[Home Network] app
Some of the window/door sensor’s
features that are available when using
the [Home Network] app are listed
below. For more information, refer to
the User’s Guide (page 17).
– Alarm system
You can use the app to arm and
disarm the alarm system, confirm
the current status of the sensor, and
view a log of previous events.
– Sensor integration
You can configure the window/door
s
ensor to trigger other system
events, such as camera recording,
turning on an electric device (such
as a lamp), etc. (Appropriate device
required.)
– Telephone alert
You can configure the system to call
a preprogrammed phone number
when the window/door sensor is
triggered.
Accessing the User’s
G
uide
The User’s Guide is a collection of
online documentation that helps you
get the most out of the [Home
Network] app.
1 iPhone
®
/iPad
®
Tap
in the app’s home screen.
A
ndroid™ devices
Tap
or press your mobile
d
evice’s menu button in the app’s
home screen.
2 Tap [User’s Guide].
Note:
R Microsoft
®
Windows
®
Internet
Explorer
®
8 and earlier versions are
not supported.
R Android 4.1 or later versions are
recommended.
R You can also access the User’s
Guide at the web page listed below.
www.panasonic.net/pcc/support/tel/
h
omenetwork/manual/
For a
ssistance, please visit http://shop.panasonic.com/support
17
Appendix
HNS101_(en_en)_0616_ver.130.pdf 17 2015/06/16 22:24:11
Specifications
R Standards
DECT (Digital Enhanced Cordless
Telecommunications)
R Frequency range
DECT: 1.92 GHz – 1.93 GHz
R RF transmission power
DECT: 115 mW (max.)
R Power source
Lithium battery CR2 (1 ´ 3.0 V,
850 mAh)
R Operating conditions
-10 °C – 40 °C (14 °F – 104 °F)
R Battery life
Up to 2 years (when window/door is
opened and closed 10 times a day,
in an environment of 25 °C (77 °F))
when using a 3.0 V, 850 mAh
battery. The battery life differs
depending on the capacity of the
battery used.
R Dimensions (height ´ width ´
depth)
Sensor unit: Approx. 102 mm ´
31 mm ´ 22 mm (4 inches ´ 1 7/32
inches ´ 7/8 inches)
Magnet unit: Approx. 37 mm ´
14 mm ´ 14 mm (1 15/32 inches ´
9/16 inches ´ 9/16 inches)
R Mass (weight)
Sensor unit: Approx. 39 g (0.09 lb),
excluding the battery
Magnet unit: Approx. 8 g (0.02 lb)
18
For a
ssistance, please visit http://shop.panasonic.com/support
Appendix
HNS101_(en_en)_0616_ver.130.pdf 18 2015/06/16 22:24:11
FCC and other
information
This device complies with Part 15 of
the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
Privacy of communications may not be
ensured when using this device.
CAUTION:
Any changes or modifications not
expressly approved by the party
responsible for compliance could void
the user’s authority to operate this
device.
NOTE:
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are
designed to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates, uses, and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause
harmful interference to radio
communications. However, there is no
guarantee that interference will not
occur in a particular installation. If this
equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the
f
ollowing measures:
– Reorient or relocate the receiving
antenna.
– Increase the separation between the
equipment and receiver.
– Connect the equipment into an
outlet on a circuit different from that
to which the receiver is connected.
– Consult the dealer or an
experienced radio/TV technician for
help.
Some devices operate at frequencies
that may cause interference to nearby
TVs and VCRs. To minimize or prevent
such interference, this device should
not be placed near or on top of a TV or
VCR. If interference is experienced,
move this device further away from the
TV or VCR. This will often reduce or
eliminate interference.
FCC RF Exposure Warning:
R This product complies with FCC
radiation exposure limits set forth for
an uncontrolled environment.
R To comply with FCC RF exposure
requirements, the device must be
installed and operated 20 cm
(8 inches) or more between the
product and all person’s body.
R This product may not be collocated
or operated in conjunction with any
other antenna or transmitter.
R For body-worn operation, the device
must be used only with a
non-metallic accessory. Use of other
accessories may not ensure
compliance with FCC RF exposure
requirements.
Notice:
R FCC ID can be found inside the
sensor unit.
For a
ssistance, please visit http://shop.panasonic.com/support
19
Appendix
HNS101_(en_en)_0616_ver.130.pdf 19 2015/06/16 22:24:11
Customer services
You may also contact us directly at: 1-800-272-7033,
Monday - Friday 9 am to 9 pm;
Saturday - Sunday 10 am to 7 pm, EST.
Accessories!
http://shop.panasonic.com/support
Customer Services Directory
Shop
for all your Panasonic gear
Go to
Get everything you need to get the most out of
your Panasonic products
Accessories & Parts for your Camera, Phone, A/V
products, TV, Computers & Networking, Personal
Care, Home Appliances, Headphones, Ba!eries,
Backup Chargers & more…
For Product Informa"on, Opera"ng Assistance,
Parts, Owner’s Manuals, Dealer and Service info
go to http://shop.panasonic.com/support
For the hearing or speech impaired TTY: 1- 877-833-8855
As of June 2015
20
For a
ssistance, please visit http://shop.panasonic.com/support
Appendix
HNS101_(en_en)_0616_ver.130.pdf 20 2015/06/16 22:24:11
Limited Warranty (ONLY FOR U.S.A.)
Limited Warranty Coverage (For USA Only)
Labor
One (1) Year
Parts
One (1) Year
To submit a new repair request and for quick repair status visit our Web Site at
http://shop.panasonic.com/support
Panasonic Products Limited Warranty
Online Repair Request
Mail-In Service--Online Repair Request
If your product does not work properly because of a defect in materials or workmanship,
Panasonic Corporation of North America (referred to as “the warrantor”) will, for the length
of the period indicated on the chart below, which starts with the date of original purchase
(“warranty period”), at its option either (a) repair your product with new or refurbished parts,
(b) replace it with a new or a refurbished equivalent value product, or (c) refund your
purchase price. The decision to repair, replace or refund will be made by the warrantor.
During the “Labor” warranty period there will be no charge for labor. During the “Parts”
warranty period, there will be no charge for parts. This Limited Warranty excludes both
parts and labor for non-rechargeable batteries, antennas, and cosmetic parts (cabinet).
This warranty only applies to products purchased and serviced in the United States.
This warranty is extended only to the original purchaser of a new product which was
not sold “as is”.
Home Network System Products
microSD card (Included model only)
90 days N/A
When shipping the unit, carefully pack, include all supplied accessories listed in the
Owner’s Manual, and send it prepaid, adequately insured and packed well in a carton box.
When shipping Lithium Ion batteries please visit our Web Site at
http://shop.panasonic.com/support as Panasonic is committed to providing the most up to
date information. Include a letter detailing the complaint, a return address and provide a
daytime phone number where you can be reached. A valid registered receipt is required
under the Limited Warranty.
IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD, THE PURCHASER WILL
BE REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING
DATE OF PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE. CUSTOMER WILL
BE CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF
OF PURCHASE.
Product or Part Name
For a
ssistance, please visit http://shop.panasonic.com/support
21
Appendix
HNS101_(en_en)_0616_ver.130.pdf 21 2015/06/16 22:24:11
Limited Warranty Limits and Exclusions
(As examples, this excludes damages for lost time, travel to and from the servicer,
loss of or damage to media or images, data or other memory or recorded content.
The items listed are not exclusive, but for illustration only.)
This warranty ONLY COVERS failures due to defects in materials or workmanship,
and DOES NOT COVER normal wear and tear or cosmetic damage. The warranty
ALSO DOES NOT COVER damages which occurred in shipment, or failures which
are caused by products not supplied by the warrantor, or failures which result from
accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty
installation, set-up adjustments, misadjustment of consumer controls, improper
maintenance, power line surge, lightning damage, modification, introduction of sand,
humidity or liquids, commercial use such as hotel, office, restaurant, or other business
or rental use of the product, or service by anyone other than a Factory Service Center
or other Authorized Servicer, or damage that is attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER
“LIMITED WARRANTY COVERAGE”.
THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT
OF ANY BREACH OF THIS WARRANTY.
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF
MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.
PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY,
ARE YOUR RESPONSIBILITY.
Some states do not allow the exclusion or limitation of incidental or consequential damages,
or limitations on how long an implied warranty lasts, so the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary
from state to state. If a problem with this product develops during or after the warranty period,
you may contact your dealer or Service Center. If the problem is not handled to your
satisfaction, then write to:
Consumer Affairs Department
Panasonic Corporation of North America
661 Independence Pkwy
Chesapeake, VA 23320
As of June 2015
22
For a
ssistance, please visit http://shop.panasonic.com/support
Appendix
HNS101_(en_en)_0616_ver.130.pdf 22 2015/06/16 22:24:11
1 Use CR2 lithium battery.
2
Use the Home Network app to access the User’s Guide
and refer to the Troubleshooting section.
IMPORTANT!
If your product is not working properly. . .
Visit our W
eb site: http://shop.panasonic.com/support
LFAQ and troubleshooting hints are available.
For your future reference
W
e recommend keeping a record of the following information to assist
with any repair under warranty.
Serial No. Date of purchase
(found inside the sensor unit)
N
ame and address of dealer
Attach your purchase receipt here.
Two Riverfront Plaza, Newark, NJ 07102-5490
© Panasonic System Networks Co., Ltd. 2014
HNS101_(en_en)_0616_ver.130.pdf 24 2015/06/16 22:24:11
Guía de instalación
Sistema de red doméstico
Sensor para Ventana/Puerta
Modelo n° KX-HNS101
Gracias por adquirir un producto Panasonic.
Este documento explica como instalar el sensor para ventana/puerta de forma
correcta.
Para obtener detalles sobre cómo usar el sistema, consulte la Guía del usua-
rio (página 13).
Lea este documento antes de usar la unidad, y guárdelo para consultarlo en el
futuro.
Para obtener ayuda, comuníquese con nosotros llamando al 1-800-272-7033 o
visite nuestro sitio web: http://shop.panasonic.com/support para clientes en los
EE. UU. (solo en inglés)
Por favor, registre su producto: http://shop.panasonic.com/support
PNQX6699YA CC0714WK1065 (E)
HNS101_(es_es)_0619_ver130.pdf 1 2015/06/22 13:01:47
Configuración
Nombres de los componentes y
funciones .........................................3
Led indicador ...................................3
Resumen de configuración ..............3
Insertar la batería ............................4
Registro del sensor para ventana/
puerta ..............................................4
Cambio de tipo de sensor ................5
Alcance de la comunicación
inalámbrica ......................................5
Colocación temporal ........................6
Instalación .......................................9
Apéndice
Prueba del sensor para ventana/
puerta ............................................13
Acceso a la Guía del usuario .........13
2
Tabla de Contenido
HNS101_(es_es)_0619_ver130.pdf 2 2015/06/22 13:01:47
Nombres de los
componentes y
funciones
n Unidad del sen-
sor
n Unidad de imán
D
B
C
A
E
E
Tapa de la unidad del sensor
M N
Se usa para confirmar el estado del
sensor o para registrar el sensor en el
hub.
Led indicador
Tapa de la unidad del imán
Marcas “ ”
Se utiliza para alinear el sensor y la
unidad del imán al momento de
instalarlos (página 6).
Led indicador
Puede oprimir M
N y verificar el Led
indicador para confirmar el estado del
sensor.
Indicador Estado
Verde, en-
cendido
La ventana/puerta está
cerrada
Rojo, encen-
dido
La ventana/puerta está
abierta
Rojo, parpa-
deante
El sensor está fuera de al-
cance del hub
Verde, par-
padeando
lentamente
Modo de registro (Opri-
mió y mantuvo oprimido
M
N)
Apagado Sin batería
Nota:
R El Led indicador no indica el estado del
sensor si el sensor no se ha registrado
(página 13).
Resumen de
configuración
1 Configuración inicial
Asegúrese de poder acceder al
sistema mediante su dispositivo móvil.
Para obtener más detalles, consulte la
Guía de configuración del sistema que
viene con su hub.
2 Inserte la batería
El sensor para ventana/puerta usa
batería.
Para obtener ayuda, visite http://shop.panasonic.com/support
3
Configuración
HNS101_(es_es)_0619_ver130.pdf 3 2015/06/22 13:01:47
3 Registro
Solo se requiere si el sensor para
ventana/puerta se compró por
separado (es decir, no como parte de
un paquete).
4 Confirme el área de instalación
Lea la información de este documento
para confirmar que el área de
instalación deseada sea la adecuada
para el correcto funcionamiento.
5 Colocación temporal
Coloque temporalmente el sensor
para ventana/puerta en la ubicación
deseada y confirme que funciona
correctamente (página 6).
6 Instalación
Instale el sensor para ventana/puerta
en la misma posición en la que se
confirmó el funcionamiento correcto
(página 9).
Insertar la batería
R USE SOLO baterías de litio CR2.
R Verifique las polaridades (
, ).
1 Quite la tapa de la unidad del sensor.
R Levante del área concava (A) y
abra la tapa de la unidad del
sensor (B).
1
2
2 Inserte la batería.
3 Coloque la tapa de la unidad del
sensor.
Registro del sensor
para ventana/puerta
Este procedimiento no es necesario para
unidades que son parte de un paquete.
Antes de que pueda usar el sensor para
ventana/puerta, se debe registrar en el hub.
Si compró los dispositivos por separado (es
decir, no como parte de un paquete), debe
registrar cada dispositivo en el hub.
Puede registrar cada unidad mediante los
botones de registro o la aplicación [Home
Network].
Uso de los botones de registro
1 Hub:
Oprima y mantenga oprimido M
OTHER DEVICEN hasta que el Led
indicador parpadee lentamente en
verde.
2 Sensor para ventana/puerta:
Quite la tapa de la unidad del sensor y
mantenga presionado M
N hasta
4
Para obtener ayuda, visite http://shop.panasonic.com/support
Configuración
HNS101_(es_es)_0619_ver130.pdf 4 2015/06/22 13:01:47
que el Led indicador parpadee
lentamente en verde (página 3).
R Cuando se ha completado el
registro, el hub emitirá un pitido
largo.
Nota:
R Para cancelar sin registrar el sensor,
oprima M
N en el hub y en el sensor
nuevamente.
R Si el registro falla, el hub emitirá varios
pitidos cortos.
Uso de la aplicación
Cuando registra el sensor para ventana/
puerta al usar la aplicación [Home
Network], puede asignarle un nombre a
sus dispositivos y agruparlos por ubicación.
Para obtener más información, consulte la
Guía del usuario (página 13).
Cambio de tipo de
sensor
Puede seleccionar si un sensor para
ventana/puerta funciona como sensor para
ventana o sensor para puerta. Para obtener
más información, consulte la Guía del
usuario (página 13).
Alcance de la
comunicación
inalámbrica
El alcance de la comunicación inalámbrica
de cada dispositivo en el sistema del hub
es de aproximadamente 50 m (160 pies) en
interiores y de aproximadamente 300 m
(1,000 pies) en el exterior. Es posible que la
comunicación inalámbrica no sea tan
confiable cuando se encuentran los
obstáculos siguientes entre el hub y otros
dispositivos.
R Puertas o pantallas metálicas
R Pare
des que contengan aislamiento de
aluminio
R Paredes de hormigón o hierro corrugado
R Ventanas de vidrio doble
R Varias paredes
R Cuando los dispositivos están en pisos o
edificios diferentes
Nota:
R Puede verificar el estado de la
comunicación del sensor para ventana/
puerta oprimiendo M
N. Si el Led
indicador está iluminado en verde o rojo,
el sensor se está comunicando de forma
adecuada con el hub. Si el Led indicador
parpadea en rojo, se encuentra fuera de
alcance del hub.
Para obtener ayuda, visite http://shop.panasonic.com/support
5
Configuración
HNS101_(es_es)_0619_ver130.pdf 5 2015/06/22 13:01:48
Colocación temporal
Antes de instalar el sensor para ventana/puerta, colóquelo temporalmente en la ubicación
deseada y confirme que funciona correctamente presionando M
N.
Importante:
R Coloque la unidad del sensor en el marco exterior de la ventana o puerta, y la unidad del
imán en la ventana o la puerta.
R El sensor para ventana/puerta no funcionará apropiadamente si las marcas “
” están
muy separadas entre sí o no apuntan una a la otra.
R Coloque ambas unidades de forma tal que las marcas “
” apunten la una a la otra y
estén a 25.4 mm (1 pulgada) de distancia la una de la otra.
Verificación del funcionamiento correcto
Después de colocar temporalmente el sensor para ventana/puerta en la ubicación deseada,
oprima M
N mientras la ventana o puerta está cerrada. El Led indicador del sensor para
ventana/puerta se ilumina de la siguiente manera.
Indicador Estado
Verde, encendido La posición de instalación es correcta.
Rojo, encendido
Las marcas “
” en la unidad del sensor y la unidad del imán
están muy alejadas la una de la otra. Vuelva a colocar la unidad
del sensor y la unidad del imán de forma tal que apunten la una
a la otra y que estén a no más de 25.4 mm (1 pulgada) de dis-
tancia.
Rojo, parpadeante La unidad del sensor está fuera de alcance del hub. Consulte la
información en página 5.
Nota:
R Dependiendo de las condiciones y del material de la superficie donde la unidad del
sensor y la unidad del imán se instalaron, el Led indicador podría iluminarse en rojo
aunque las marcas “
” apunten la una a la otra y estén a no más de 25.4 mm
(1 pulgada) de distancia.
6
Para obtener ayuda, visite http://shop.panasonic.com/support
Configuración
HNS101_(es_es)_0619_ver130.pdf 6 2015/06/22 13:01:48
Ejemplo 1: Instalado en el costado izquierdo de la ventana
Correcto
1
A
B
Verde
1
Las marcas “ ” están apuntadas directamente entre sí y están a 25.4 mm (1 pulgada)
de distancia.
Resultado: Cuando oprima M
N (A), la luz del Led indicador estará en verde (B).
Incorrecto
2
3
4
A
B
Rojo
2
Las marcas “ ” están alineadas, pero las unidades están muy separadas.
3
Las marcas “ ” están alineadas, pero el marco de la ventana es muy grueso; las
unidades están muy separadas.
4
Las marcas “ ” no están alineadas. La unidad del imán está demasiado alta.
Resultado: Cuando oprima M
N (A), la luz del Led indicador estará en rojo (B).
Para obtener ayuda, visite http://shop.panasonic.com/support
7
Configuración
HNS101_(es_es)_0619_ver130.pdf 7 2015/06/22 13:01:48
Ejemplo 2: Instalado en el costado derecho de la ventana
Correcto
1
A
B
Verde
1
Las marcas “ ” están apuntadas directamente entre sí y están a 25.4 mm (1 pulgada)
de distancia.
Resultado: Cuando oprima M
N (A), la luz del Led indicador estará en verde (B).
Incorrecto
2
3
4
A
B
Rojo
2
Las marcas “ ” están alineadas, pero las unidades están muy separadas.
3
Las marcas “ ” están alineadas, pero el marco de la ventana es muy grueso; las
unidades están muy separadas.
4
Las marcas “ ” no están alineadas. La unidad del imán está demasiado alta.
Resultado: Cuando oprima M
N (A), la luz del Led indicador estará en rojo (B).
8
Para obtener ayuda, visite http://shop.panasonic.com/support
Configuración
HNS101_(es_es)_0619_ver130.pdf 8 2015/06/22 13:01:48
Instalación
Instale el sensor para ventana/puerta en la misma posición donde se confirmó el
funcionamiento correcto (página 6). Ahora puede instalar el sensor para ventana/puerta con
tornillos o cinta adhesiva de doble cara, en función de su preferencia o del material del área
de instalación.
Nota:
R Al instalar, asegúrese de que la batería esté colocada adecuadamente y que la tapa de
la unidad del sensor
esté cerrada por completo.
R Cuando instale en superficies de madera, use tornillos. No use cinta adhesiva de doble
cara.
Ajuste con tornillos
1 Quite las tapas de cada unidad.
R Levante del área concava (A) y abra la tapa de la unidad del sensor (B).
1
2
1
2
Para obtener ayuda, visite http://shop.panasonic.com/support
9
Configuración
HNS101_(es_es)_0619_ver130.pdf 9 2015/06/22 13:01:48
2 Unidad del sensor:
Coloque la unidad del sensor.
1
Tornillos
2
86.2 mm (3 25/64 pulgadas)
Unidad del imán:
Coloque la unidad del imán.
3
Tornillos
4
24.4 mm (31/32 pulgadas)
2
4
1
1
3
3
5
3 Coloque las tapas.
Importante:
R
5
Alinee las marcas “ ” en la unidad del sensor y en la unidad del imán de forma tal
que se apunten la una a la otra y estén a no más de 25.4 mm (1 pulgada).
10
Para obtener ayuda, visite http://shop.panasonic.com/support
Configuración
HNS101_(es_es)_0619_ver130.pdf 10 2015/06/22 13:01:48
Ajuste con cinta adhesiva de doble cara
Nota:
R Asegúrese de que las superficies de la unidad del sensor, la unidad del imán y el área de
instalación están limpias y secas antes de colocar la cinta adhesiva de doble cara.
1 Verifique que se hayan colocado la tapa de la unidad del sensor y la tapa de la unidad
del imán.
2 Pegue la cinta adhesiva de doble cara a la unidad del sensor y la unidad del imán.
R Ase
gúrese de que la cinta cubra los hoyos de los tornillos en la parte posterior de
cada unidad.
5
3 Instale la unidad del sensor y la unidad del imán.
R Presione con firmeza en cada unidad para asegurar una adhesión sólida a la
superficie de instalación.
Importante:
R
5
Alinee las marcas “ ” en la unidad del sensor y en la unidad del imán de forma tal
que se apunten la una a la otra y estén a no más de 25.4 mm (1 pulgada).
Para obtener ayuda, visite http://shop.panasonic.com/support
11
Configuración
HNS101_(es_es)_0619_ver130.pdf 11 2015/06/22 13:01:48
Cómo extraer cuando se asegura con cinta adhesiva de doble cara
1 Ate un pedazo de hilo a dos palos, destornilladores, etc.
2 Tire firmemente del hilo y úselo para cortar la cinta de doble cara, y luego elimine
cualquier exceso de cinta.
1
Exceso de cinta
1
12
Para obtener ayuda, visite http://shop.panasonic.com/support
Configuración
HNS101_(es_es)_0619_ver130.pdf 12 2015/06/22 13:01:48
Prueba del sensor para
ventana/puerta
Puede observar el Led indicador del sensor
para ventana/puerta y probar el
funcionamiento del sensor para ventana/
puerta.
1 Quite la tapa de la unidad del sensor.
2 Oprima M
N en la unidad del
sensor.
3 Abra y cierre la ventana o puerta
varias veces.
R Asegúrese de que el Led indicador
se encienda en verde cuando
cierra la ventana o puerta.
4 Presione M
N de nuevo.
Nota:
R Si el Led indicador se enciende en rojo
cuando la ventana o la puerta está
cerrada, el sensor para ventana/puerta
no está bien instalado. Revalúe la
posición de la unidad del sensor y la
unidad del imán (página 6).
Acceso a la Guía del
usuario
La Guía del usuario es una colección de
documentación en línea que lo ayuda a
aprovechar al máximo la aplicación [Home
Network].
1 iPhone
®
/iPad
®
Toque
en la pantalla de inicio de
la aplicación.
Dispositivos Android™
Toque
u oprima el botón menú de
su dispositivo en la pantalla de inicio
de la aplicación.
2 Toque [Guía del Usuario].
Nota:
R No se admite Microsoft
®
Windows
®
Internet Explorer
®
8 y versiones
anteriores.
R Se recomienda Android 4.1 y versiones
posteriores.
R También puede acceder a la Guía del
usuario mediante la página web a
continuación.
www.panasonic.net/pcc/support/tel/
homenetwork/manual/
Para obtener ayuda, visite http://shop.panasonic.com/support
13
Apéndice
HNS101_(es_es)_0619_ver130.pdf 13 2015/06/22 13:01:48
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
Panasonic KX-HNS101 Instrucciones de operación
- Tipo
- Instrucciones de operación
en otros idiomas
Artículos relacionados
-
Panasonic KXHNS101 El manual del propietario
-
-
-
-
-
-
-
-
Panasonic KXHNS101 Instrucciones de operación
-