EcoFlow Smart Home Panel Combo(13 relay modules) Manual de usuario

Marca: EcoFlow

Modelo: Smart Home Panel Combo(13 relay modules)

Tipo: Manual de usuario

Smart Home Panel Installation Manual

WARNING

The EcoFlow Smart Home Panel must be installed by a licensed electrician,

who should be familiar with all electrical codes, electrical wiring practices and

experience working with home electrical systems. Any accident, damage or

personal injury caused by incorrect installation is the sole responsibility of the

user.

CONTENTS

3. Product Details

2. Specifications

4. What's in the box

5. Installation SOP Checklist

1. Safety Instructions

3.1 External Features

3.2 Internal Features

6. Installation Steps

7. System Commissioning and App Setup

8. FAQ

6.1 Preparation

6.2 Installation

6.2.1 Installing the Relay Module

6.2.2 Mounting

6.2.3 Wiring

6.1 Preparation

6.2 Installation

6.2.1 Installing the Relay Module

6.2.2 Mounting

6.2.3 Wiring

1. Open all connected upstream circuit breakers and make sure the Grid Power Indicators are off.

2. Turn off DELTA Pro(s) from the SHP and ensure the DELTA Pro Power Indicators are off.

3. The alarm will sound if the SHP is energized while the front cover is open. Please ensure that the

unit is de-energized and the alarm has stopped

The SHP MUST be completely de-energized before being serviced

Complete the following to de-energize the SHP

1. The product must be installed by a licensed electrician and verified by local AHJ (Authority

Having Jurisdiction, i.e., your city, town, county or state).

2. The SHP defaults to grid mode when not powered. For safety, do not access or disconnect any

load circuits when there is an internal fault. Power down those loads and contact a licensed

electrician or EcoFlow technical support.

3. This product is not intended to be used as a service disconnect. To completely de-energize the

product, the user MUST open the upstream breakers as well as physically unplug all DELTA Pros.

Failure to do so may present a shock hazard.

4. DO NOT unplug relay modules while SHP is energized, because unplugging the relay module

while the SHP is energized may cause damage to the relay modules and SHP.

5. Smart Home Panel by itself does not provide an AFCI (Arc Fault Circuit Interrupter) function. AFCI

or GFCI protection may be available with an external AFCI accessory. Consult EcoFlow support

for AFCI or GFCI solutions.

6. All upstream breakers feeding SHP should be non-GFCI/AFCI. GFCI and AFCI protection should

be downstream of the SHP using GFCI/AFCI breakers or outlets. Follow NEC or local electrical

codes for AFCI or GFCI installation. An additional accessory panel to aid with installation of AFCI

circuits may be available from EcoFlow.

7. Do not use the product near a heat source, such as a fire or furnace. Do not place flammable

gases or liquids (e.g. Gasoline) near the device.

8. If there is a loud noise in the relay module, there may be a ground fault downstream of the SHP.

The user should clear the fault and replace the relay module before resetting the SHP for normal

use.

9. Do not use the SHP if the Short-Circuit Current Rating (SCCR) at the electrical service entrance is

above 10kA.

10. Do not install or operate the product outdoors or in damp/wet conditions.

11. Do not install or operate the product in extreme temperatures.

12. Do not use the product if it is damaged or appears to be damaged.

13. Do not connect the relay channels to circuit breakers higher than their current rating. Doing so

can result in damage to the relay modules.

14. The split-phase mode should be used for multi-wire circuits (MWBC, circuits sharing a balanced

neutral), and the circuits split across the two phases appropriately.

15. Adhere to all local and national safety regulations for installation and use.

16. If an overcurrent fault (breaker tripped) occurs, the corresponding relay module must be replaced

to ensure safe operation in the future.

17. This product is designed for residential use only.

18. Upstream circuit breakers protect the SHP only in grid mode. Only use circuit breakers with a fault

current interruption capability of 10kA or greater, 4ms or 5kA, 8ms.

19. The maximum total current for all input circuits under the grid mode is 160A.

1. Safety Instructions

2. Specifications

General Information

Weight

Dimensions

Mounting Type

Standard Connector

Type of Enclosure

Warranty Description

Maximum # of Circuits Controlled

Rated System Voltage

Max Total Input Current

Short Circuit Rating

Rated Relay Module Current

Rated Max DELTA Pro Input

DELTA Pro Charging Power

Max Connected Battery Energy

Operating Humidity (RH)

20 lbs (9 kg)

19.7x11.8x4.7 in (500x330x120 mm)

Wall Mount

EcoFlow Infinity Port

Type 1

5 Years

120V/240V

160A

10kA

30A, 20A, 15A

7200W Max (2x3600W)

6800W Max (2x3400W)(Max. charging time <3hrs)

21.6 kWh (6x3.6kWh)

5-85%

1. Multiple sources power this equipment.

2. Electrical equipment should be serviced by authorized personnel only.

3. This equipment is not intended to be used as a service disconnect breaker.

4. Upon losing power, this product automatically switches to the power station.

5. This equipment and downstream load can only be de-energized by opening all upstream

breakers and physically unplugging all DELTA Pros.

DANGER

The SHP can be set up to control a total of 10 load circuits, circuits 1, 3, 5, 7, 9 on the left and 2, 4, 6, 8,

10 on the right. There is a button allowing users to manually reset each circuit relay if there has been

an overcurrent event on the circuit. An indicator lamp on the button turns red if there is a fault in that

circuit.

A lightning bolt indicator for each load circuit is illuminated if that load circuit is energized through one

of the sources (grid or power station).

There are three energization indicators on the SHP, one for the grid, two for the DELTA Pros. If any of

these indicators are illuminated, SHP is energized from that source and, therefore, cannot be opened to

be serviced.

There are two infinity ports on the SHP, which can be either on the bottom of the SHP (default),

or relocated to the front. They connect DELTA Pros to the SHP through the Infinity Cable (one for

each DELTA Pro). Once plugged in, SHP and DELTA Pro will try to establish connection through

communication and SHP’s control circuitry may be powered via DC current from the DELTA pro. Press

the enable button located near the infinity port (labeled “AC 1” or “AC2” to make DELTA Pro ready for

output.

When the DELTA Pro load circuits are energized, an alarm will sound if the front panel cover is opened.

To de-energize the product, all upstream breakers must be opened and both DELTA Pros must be

unplugged.

1. Load Circuit Control Board

3.1 External Features

2. Grid Indicator and Infinity Port Indicator

3. Infinity Port and Enable Button

4. Panel Open Alarm System

3. Product Details

This button can be used to turn on the Bluetooth hotspot for 5 minutes for the user to connect.

This indicator is normally off if no fault is present inside the SHP. It will turn red if there is a fault in

the product. Users can go to the app for a fault diagnostic report. If there is an issue, please contact

customer support for assistance.

5. IOT Reset Button and Indicator

6. Error Indicator

The pause button will physically isolate the 10 load circuits and lock out both connected DELTA Pros.

A signal from the SHP will tell the DELTA Pros to stop outputting power. Please note that this does not

substitute for a service disconnect, nor does it substitute for the de-energization procedure required

before servicing.

This is the only “quick disconnect” that can be used to manually cut all power in an emergency.

AC in and Pro in still energize.

7. Power Station Pause/Resume Button

3.2 Internal Features

NOTE

1. Output Wire Connectors

2. Communication Ports connecting to the key panel

3. Relay Modules

These are the wire connectors for output hot wires going to the load.

The relay modules are available in different current ratings, 15A, 20A and 30A. These modules contain

two relays for each circuit as well as an overcurrent protection fuse. Each module can be individually

replaced without affecting other circuits. De-energize the SHP before replacing any module.

4. DELTA Pro Wire Connectors

5. Infinity Ports

6. Cooling Fan

7. Ground Bus Bar

8. Input Wire Connectors

9. Switching Connector for Single/Split Phase Operation

These are wire connectors for DELTA Pro. There is one hot wire and one neutral wire required for each

DELTA Pro. At least one neutral wire must be connected to the main panel even if no DELTA Pro is

used. This neutral is used as a return path for DELTA Pro to power your circuits.

Infinity ports can be installed either on the front or the bottom of the product. Users can choose to

switch the position of the Infinity ports. This can improve cable management in tight quarters.

The cooling fan is activated under extreme operating conditions to reduce the ambient temperature

inside of the unit.

This is the ground bus bar, which should be connected to the ground bus bar in the main electrical

panel. The panel casing is connected to this ground. NOTE: Please follow NEC and/or local code

requirements with regard to bonding neutral and ground. Bonding should be done at the first means of

disconnect, which is the service panel, NOT the SHP.

These are the wire connectors for hot wires coming from the circuit breakers in your main panel.

For split phase operation (North America and Japan ONLY), this connector should be removed

permanently from the product. Split-phase also requires additional setup in the EcoFlow app.

4. What’s in the Box

Smart Home Panel

Product User Manual Product Installation

Manual

Wall mounting brackets

A bag of accessoriesInfinity Cable and

Wires

The AWM wires can be removed from the harness plugs and replaced with an appropriate length

and type of cable.

NOTE

5. Installation SOP Checklist

No. Checklist Status

Before installation- Project information

Determine the installation location. The Smart Home Panel is rated to IP20,

therefore, it needs to be installed away from direct sunlight, rain, snow and

moisture.

2Determine the distance between the SHP and main electrical panel.

Determine if there is a split-phase or double pole load (240V/200V or

MWBC, USA and Japan only) that needs to be connected to the SHP. Channel

1, 3, 5, 7, 9 AC input should be connected on the same phase (phase a),

whereas Channel 2, 4, 6, 8, 10 AC input should be connected on the opposite

phase (phase b) when using the split-phase function. Mismatched phases will

result in an error condition and SHP will not function properly.

4Confirm the number of loads to be connected to SHP. You can connect up to

10 single pole load circuits, or up to 5 double pole load circuits.

Determine whether the upstream circuit breakers of the selected loads

require AFCI or GFCI protection. This can be accomplished with an on-site

inspection or photo or video of the panel from the end user.

Determine and gather required materials. SHP can support up to 1 1/2 “

conduit via five knockouts. Ensure that necessary adjustment factors (for

number of conductors) are accounted for and that wire ampacity is sized

appropriately. For longer runs it is recommended that you use separate

conduits for the input and output wires. USA ONLY - For AFCI and GFCI

breakers, an additional standard overcurrent trip breaker is required. For

circuits where AFCI protection is required, metal conduit or whip to the

SHP from the main panel is required to comply with NEC requirements. An

external AFCI enclosure (available from EcoFlow) to house AFCI breakers is

also required downstream of the SHP.

During installation - Circuit breaker and relay module

1The current rating of relay module must match the upstream circuit breaker.

Failure to do so may cause overcurrent protection to fail.

2The ampacity rating of wiring used should match the circuit current. Using an

undersized cable may cause overheating and even a fire.

3All upstream breakers should be non-GFCI/AFCI. Any AFCI/GFCI breakers

need to be moved downstream of the SHP using an optional accessory box.

During installation - Wiring

When using split phase, the Channel 1, 3, 5, 7, 9 AC input should be connected

with hot wires on the same phase, the Channel 2, 4, 6, 8, 10 AC input should be

connected with hot wires on another phase.

2For split phase operation, the Switching Connector should be removed

permanently from the SHP.

3When using single phase, each load circuit AC input should be connected to

the hot wire.

Install the relay modules in the corresponding places and secure by tightening

the screws. Failure to do so may cause the relay module to come loose, which

will produce an error and disconnection of the load channel, as well as risk

overheating and fire.

During installation - Check wiring

1With a multimeter in continuity setting, confirm that the hot wire in of each

SHP channel is not shorted to neutral.

2With a multimeter in continuity setting, confirm that the hot wire in of each

SHP channel is not shorted to ground.

Commissioning

1Make sure the power stations are enabled and that the stop button is off

(raised).

2Close the upstream breaker of DELTA Pro and energize the DELTA Pro AC

Input channel. The grid indicator (white) will turn on if there is no fault.

3Turn each branch circuit breaker back on one by one and check the indicator

status of each channel and power indicator. The indicators will stay white.

If you haven’t done so already, download the EcoFlow app from Google Play

or the App Store and create an EcoFlow account. Open the app on your

mobile device, log into the app and add the Smart Home Panel to your device

pool. For first time users, the app will lead through a commissioning process

to setup the SHP.

5Update the firmware of the Smart Home Panel to the latest version, then

check whether there are any errors reported on the app.

Follow the instructions in the app to conduct device wiring testing. If the

device wiring testing fails, correct the wiring following the prompts in the app

and re-run the wiring test.

7Turn on the DELTA Pro and update the firmware to the latest version.

No. Checklist Status

Connect the DELTA Pro and Smart Home Panel using the Infinity cable. For

split-phase, two DELTA Pros and two infinity cables are required. Turn on the

main power button of DELTA Pro, then press the On/Off button (AC button,

near the infinity port) on the SHP to enable each DELTA Pro.

Switch the power supply from grid to power station for each channel via

the app. Check whether the switchover is successful and there are no errors

reported on the app. Follow the instructions on the app to fix the errors if

any.

Set up the charging for DELTA Pro on the app (if AC grid charging is desired),

check whether the DELTA Pro is recharged successfully and there are no

errors reported on the app. Follow the instructions on the app to fix the

errors if any.

6. Installation Steps

6.1 Preparation

Tools and Items Needed for Installation:

Tools required:

1. Level

2. Phillips head screwdriver, Torx T20 screwdriver and 7mm socket screwdriver

3. Pliers

4. Wire cutters

5. Wire nuts

6. Drill

7. Conduit (e.g. 1,1/4 inch and 1 inch), Conduit whip

8. Wire harness

9. Tape measure

10. Multimeter

11. Voltage detector

12. Purchase a new double pole 30A circuit breaker or two single pole 30A circuit breakers. (NOTE:

these breakers may be required to be handle tied per code.)

WARNINGWARNING

Installation of this product involves high voltage. Please hire a licensed electrician to perform the

installation.

Circuit

1Refrigerator 700W running

2000W startup

200W

1400W

800W

700W

1000W

400W

500W

300W

1200W

700W

1000W

Kitchen Light

Kitchen Plug

Bedroom Plug

Bedroom Light

Bathroom Light

Living Room Light

Furnace

Sump Pump

Plug

3 4

5 6

7 8

910

CircuitName NameWattage Wattage

Load Calculation Example

The total DELTA Pro wattage (3600W for single Pro or 7200W for two Pros) should be greater than

the total continuous running wattage of all backed up loads plus the largest start-up wattage.

Total Running Load

Largest Estimated Simultaneous Running Load (LESRL)

Largest Startup Wattage (LSW)

Minimum Backup Power Needed = LESRL + LSW

6900 W

2300 W

2000 W

4300 W (Two DELTA Pros)

Inductive loads such as air conditioners, clothes dryers or pumps have high Inrush current when

starting. This may trip the relay modules because of overload. Ensure the circuit is sized appropriately

for the intended load.

Once you have determined the load circuits that you want to back up, fill out the table below. The

numbering arrangement is the same as your SHP.

Circuit

3 4

5 6

7 8

910

Circuit

Original

Phase

Original

Phase

Name Name

NOTE

6.2 Installation

De-energize the system: When you are ready to start the installation work, turn off the main breaker

as well as each branch circuit breaker intended to be connected. Ensure that DELTA Pros are not

connected to the SHP as well.

The relay modules are shipped separately from the main unit. These modules include two switching

relays and a fuse. The fuse is for load circuit protection in the backup mode only and therefore

should match the current rating for the circuit breaker upstream of that load circuit. There are three

standard ratings for the modules, 15A, 20A and 30A. Users should install these modules at the position

corresponding to the load circuits that they plan to use it for according to the diagram below. The

diagram below shows the module position corresponding to the circuit number.

There are 10 module mounting spaces inside the SHP as shown below. 4 out of the 10 channels

(channel 1-4) have a maximum of 30A current rating, the rest have a maximum 20A current rating. No

load circuit larger than the maximum current rating for a channel should be connected. Once placed

into position, two screws are used to secure the module into place.

It's easier if the knockouts are removed before the SHP is installed on the wall.

NOTE

The actual continuous current rating for each relay module is 80% of module rating. For example,

for the 20A relay module, the continuous current rating is 20A × 0.8 = 16A.

6.2.1 Installing the Relay Module

1. (a) Open the panel cover using the T20

screwdriver.

(b) Slide out the screw cover on top.

Relay Module Position

Install Relay Module

30A MAX

20A MAX

DELTA Pro DELTA Pro

2. (a) Plug in each relay module and seat firmly (it is

recommended to use the palm of your hand).

(b) Secure the relay module by tightening the two screws.

(d) The Relay Module installation is complete.

(e) Repeat for all 10 relays. 10 relays must be installed even

if they are not all used

After you have placed the relay module inside and fastened the screws, attach both top and bottom

mounting brackets to the SHP as shown below.

6.2.2 Mounting

Position the SHP center to center to your main panel.

Please follow the local safe electrical clearance distance.

Attach the top mounting bracket along the top edge

of the mark on the wall. Make sure you also check the

length of the flexible conduit.

wall

Hang the SHP up on the wall bracket.

Secure the bottom mounting bracket to the wall. wall

Wiring inside the Smart Home Panel

All wires come labeled in the box, 12 input wires, labeled "1 in - 10 in" "Pro1 in, Pro2 in" connected to the

circuit breakers, 10 output wires, labeled "1 out - 10 out" connecting to the load hot wires, two neutral

wires connecting to the neutral bus bar in the main panel and ground wire connecting to the ground

bus bar in the main panel. Users should connect all input, output, neutral and grounds wire to their

designated connectors inside the SHP.

6.2.3 Wiring

Pro1,N1,N2,Pro2

Ground bar

Output connectors

Input connectors

NOTE

Two neutral wires and the ground wire must be connected to the main panel in order for the SHP to

operate correctly and safely.

The maximum current for circuits 1-4 is 30A. Maximum current for circuits 5-10 is 20A. The current

rating for each circuit should not be exceeded. Please plan the load circuits appropriately. If a non-

metallic conduit is used to connect between the main panel and SHP, an equipment grounding

conductor needs to be present inside each conduit. Additional ground wires can be connected

between the ground bar inside the main panel and the SHP.

You may use your own wires with the connectors instead of the included wire. Use a screwdriver to

remove the connectors, strip the wire and then insert and torque down

1. Run a cable from the grounding bus of the main electrical panel to the grounding bar in SHP. Install

two 30A single pole or one 30A double pole circuit breaker(s) to the main electrical panel and connect

Pro 1 and Pro 2 modules in SHP with a 10AWG cable to provide AC charging and overcurrent protection

for the Delta Pro(s).

Single-phase without GFCI or AFCI breakers

Below illustrates a typical single-phase 120V (100V in Japan) setup. SHP can be connected to the main

electrical panel to provide backup power to ten 120V load circuits. All input wires should be routed

through the bottom conduit into the SHP and output wires through the upper conduit. The whole

system is single point grounded at the main electrical panel.

6.2.3.1 Single Phase Setup (120V)

1. Turn off the main breaker as well as the 10 branch circuit breakers intended to be connected in the

main panel and use a voltage detector or voltmeter to make sure the system is fully de-energized.

2. Remove the front cover of the main panel. Keep in mind that the grid side of the main panel

(upstream of the main breaker) is still energized.

3. Remove the knockouts that you want to use on both the SHP and the main electrical panel.

4. Attach both top and bottom conduit to the SHP and main electrical panel.

5. Pull all wires (Input, output, neutral and ground) from the SHP to the main electrical panel.

6. Connect the two neutral wires and the ground wire to the neutral and ground bus respectively.

Cut them to the appropriate length before connecting.

7. Remove the hot wire from the circuit breaker. Connect each load hot wire to the corresponding

output wire from the SHP using wire nuts (for example, the output wire labeled “1 out” means it’s

the output for channel 1). Make sure it’s connected to the right number as planned.

8. Connect the input wire, with the same number (for example, if you used “1 out”, now you should

find the red wire labeled “1 in”), to the circuit breaker planned. Make sure you cut them to the

appropriate length before connecting.

9. Repeat step 7 & 8 for all 10 load circuits.

10. Each charging circuit for DELTA Pro needs to feed off a single 30A breaker from the main panel

to enable the fast charge function. If not available, 30A circuit breakers need to be purchased and

installed. The wires corresponding to the PRO charging wires are labeled “PRO1 in” and “PRO2 in”.

If the 30A breaker is not used, the correct current rating should be entered into the app later on to

prevent the circuit breaker tripping from charging current. It is recommended to handle tie both

charging breakers or use a double pole breaker. This makes de-energization of the SHP safer for

future servicing.

Wiring in the Electrical panel

2. Connect input wires from SHP to corresponding breakers of the main electrical panel and output

wires to the load port of the main electrical panel.

To Load

Utility Power

Ground Bus

Neutral Bus

Main

To Load

Two Ne w Beakers added

for Delt a Pr o Charging

11/4in Conduit

To Load

Utility Power

Ground Bus

Neutral Bus

Main

To Load

Two Ne w Beaker s adde d

for Delta Pro Chargin g

Single-phase with GFCI or AFCI breakers

1. Uninstall the upstream A/GFCI breaker of the main electrical panel and replace with normal breakers,

then install the A/GFCI breakers into the EcoFlow AFCI/GFCI Box (please refer to the manual of

EcoFlow AFCI/GFCI Box for details).

2. Follow steps below to wire up the product:

2.1. Connect the grounding wire from the ground bus of the main electrical panel to the EcoFlow AFCI/

GFCI Box.

2.2. Connect input wires from SHP to corresponding breakers of the main electrical panel.

2.3. Connect output wires from SHP to corresponding breakers of the EcoFlow AFCI/GFCI Box.

2.4. Connect A/GFCI breakers of the EcoFlow AFCI/GFCI Box back to the load port of the main

electrical panel.

Metallic conduit

To Load

Utility Power

Ground Bus

Neutral Bus

Main

To Load

Two Ne w Beaker s adde d

for Delta Pro Chargin g

Split-phase without GFCI or AFCI breakers

1. Remove the switching connector of SHP.

2. Connect L1 phase and L2 phase of the main electrical panel to corresponding outputs and inputs of

SHP (L1 phase to 1, 3, 5, 7, 9 of SHP; L2 phase to 2, 4, 6, 8, 10 of SHP).

L1 phase wiring

Smart Home Panel Main Electrical Panel

To Loa

Utility Power

Ground Bus

Neutral Bus

Main

To Loa

Two Ne w Beaker s added

for D elta Pr o Charging

1 in Conduit

11/4in Conduit

Split phase setup is different from the single-phase mode in that.

1. The switching connector needs to be unplugged from the SHP.

2. Two DELTA Pros need to be connected at the same time to support the split phase operation.

3. Circuits 1,3,5,7 and 9 are connected to the same phase in the SHP when phase split, and should be

connected to the same phase inside the main electrical panel. Circuits 2,4,6,8 and 10 should be

connected to the other phase.

6.2.3.2 Split Phase Setup (240V)

To Load

Utility Power

Ground Bus

Neutral Bus

Main

To Load

Two Ne w Beaker s adde d

for Delt a Pr o Charging

1 in Conduit

1 1/4in Conduit

Smart Home Panel

Split-phase with GFCI or AFCI breakers

Main Electrical Panel

1. Connect the grounding wire from the ground bus of main electrical panel to the grounding terminal

of EcoFlow AFCI/GFCI Box.

Main electrical panel

To Load

Utility Power

Ground Bus

Neutral Bus

Main

To Load

Two New Beaker s adde d

for Delt a Pro Charging

L2 phase wiring

2. Connect L1 phase and L2 phase of the main electrical panel to corresponding inputs of SHP. Output

wires of SHP are connected to corresponding hot wire terminals.

L1 phase wiring

L2 phase wiring

To Load

Utility Power

Ground Bus

Neutral Bus

Main

To Load

Two New B eaker s added

for Delt a Pro Charging

To Load

Utility Power

Ground Bus

Neutral Bus

Main

To Load

Two New Beaker s adde d

for Delt a Pro C harging

Metallic conduit

Wire nuts

Metallic conduit

After you have connected all wires accordingly, clean up all the wires and tie them using a wire

harness. Close the front panel and tighten the screws to secure the door. Label the circuit names

accordingly on the SHP.

1. Download the EcoFlow app from the App Store, Google Play Store or EcoFlow official site. Set

up the account and sign in.

2. Connect a DELTA Pro to the SHP without pressing the enable button.

3. Press the IOT button to enable Bluetooth connection. When the indicator light is flashing, it’s

ready to pair with the EcoFlow App.

4. Open the EcoFlow App and add the device from the “+” icon on the top right. Find the SHP and

click the icon to pair. After Bluetooth connection, you will be asked to choose the Wi-Fi and

enter Wi-Fi password to finish Internet connection.

5. For first time users, the app will lead through a commissioning process to setup the SHP. Simply

follow the steps to complete the process. Once you have finished the commissioning process on

the app, you are ready to energize the SHP.

6. After completing the device wiring test, press the enable button (near the infinity port) for the

connected DELTA Pro. The power indicator should turn green. Watch for any abnormal signs

and fault indication.

7. If there is no sign of fault, turn the main breaker back on and then turn each branch circuit

breaker back on one by one and watch for any fault indication.

WARNING

The SHP defaults to grid mode when without power, which means the load is automatically

connected to the grid power if no power is supplied to the SHP or it’s started for the first time.

Please make sure energization of load circuits do not endanger any person or incur any property

damage before closing the main breaker.

7. System Commissioning and App Setup

a. If the device wiring testing reports any errors, or if there are any errors, please resolve the issue

following the message shown on the App or contact our customer support from the Help Center

in the App. You can leave your SHP as long as there is no indication of electrical or other type of

sign for a fault. The default mode for SHP is grid power so it will not affect your use of power.

b. If there is no sign of error, congratulations! You are ready to go!

APP

Control and monitor EcoFlow portable power stations and the SHP remotely with the EcoFlow App.

Download at: https://download.ecoflow.com/app

8. FAQ

1. Can the SHP connect to a roof solar system, if yes, how?

For DC coupled solar panel system, currently, only solar panels with the correct output

parameters can be connected to the system. See the DELTA Pro manual for supported solar

panel specifications.

2. Does the SHP support split phase 240V output?

Yes, it does up to 30 amps, 7200W. This requires two DELTA pros and two infinity cables..

3. What's the maximum number of DELTA Pros and extra batteries that can be connected to the

SHP?

A maximum of 2 DELTA Pros and 4 extra batteries can be connected, with a total of 7200W output

power and 21.6kWh of energy.

4. Can multiple smart panels be used at the same time in one house?

Yes.

5. Can I manually switch between grid power and backup power?

Yes. Through the EcoFlow App.

6. How many circuits can SHP manage?

A maximum of 10 single phase circuits or 5 split phase circuits.

7. Is there any protection function in the SHP?

Yes. There is a relay based overcurrent and over-temperature protection system in both the grid

and backup mode. There is also a fuse for fault protection in the backup mode only.

8. Is there an AFCI function provided by the SHP?

No, an additional accessory needs to be purchased to house an AFCI breaker

By using EcoFlow Products, Applications, and Services, you consent to the EcoFlow Terms of Use and

or the official EcoFlow website at https://ecoflow.com/pages/terms-of-use and https://ecoflow.com/

pages/privacy-policy.

Smart Home Panel Installation Manual

WARNING

The EcoFlow Smart Home Panel must be installed by a licensed electrician,

who should be familiar with all electrical codes, electrical wiring practices and

experience working with home electrical systems. Any accident, damage or

personal injury caused by incorrect installation is the sole responsibility of the

user.

CONTENTS

3. Product Details

2. Specifications

4. What's in the box

5. Installation SOP Checklist

1. Safety Instructions

3.1 External Features

3.2 Internal Features

6. Installation Steps

7. System Commissioning and App Setup

8. FAQ

6.1 Preparation

6.2 Installation

6.2.1 Installing the Relay Module

6.2.2 Mounting

6.2.3 Wiring

6.1 Preparation

6.2 Installation

6.2.1 Installing the Relay Module

6.2.2 Mounting

6.2.3 Wiring

1. Open all connected upstream circuit breakers and make sure the Grid Power Indicators are off.

2. Turn off DELTA Pro(s) from the SHP and ensure the DELTA Pro Power Indicators are off.

3. The alarm will sound if the SHP is energized while the front cover is open. Please ensure that the

unit is de-energized and the alarm has stopped.

The SHP MUST be completely de-energized before being serviced

Complete the following to de-energize the SHP

1. The product must be installed by a licensed electrician.

2. The SHP defaults to grid mode when not powered. For safety, do not access or disconnect any

load circuits when there is an internal fault. Power down those loads and contact a licensed

electrician or EcoFlow technical support.

3. This product is not intended to be used as a service disconnect. To completely de-energize the

product, the user MUST open the upstream breakers as well as physically unplug all DELTA Pros.

Failure to do so may present a shock hazard.

4. DO NOT unplug relay modules while SHP is energized, because unplugging the relay module

while the SHP is energized may cause damage to the relay modules and SHP.

5. Smart Home Panel by itself does not provide an AFCI (Arc Fault Circuit Interrupter) function. AFCI

or GFCI protection may be available with an external AFCI accessory. Consult EcoFlow support

for AFCI or GFCI solutions.

6. All upstream breakers feeding SHP should be non-GFCI/AFCI. GFCI and AFCI protection should

be downstream of the SHP using GFCI/AFCI breakers or outlets. Follow local electrical codes for

AFCI or GFCI installation. An additional accessory panel to aid with installation of AFCI circuits

may be available from EcoFlow.

7. Do not use the product near a heat source, such as a fire or furnace. Do not place flammable

gases or liquids (e.g. Gasoline) near the device.

8. If there is a loud noise in the relay module, there may be a ground fault downstream of the SHP.

The user should clear the fault and replace the relay module before resetting the SHP for normal

use.

9. Do not use the SHP if the Short-Circuit Current Rating (SCCR) at the electrical service entrance is

above 10kA.

10. Do not install or operate the product outdoors or in damp/wet conditions.

11. Do not install or operate the product in extreme temperatures.

12. Do not use the product if it is damaged or appears to be damaged.

13. Do not connect the relay channels to circuit breakers higher than their current rating. Doing so

can result in damage to the relay modules.

14. Adhere to all local and national safety regulations for installation and use.

15. If an overcurrent fault (breaker tripped) occurs, the corresponding relay module must be replaced

to ensure safe operation in the future.

16. This product is designed for residential use only.

17. Upstream circuit breakers protect the SHP only in grid mode. Only use circuit breakers with a fault

current interruption capability of 10kA or greater, 4ms or 5kA, 8ms.

18. The maximum total current for all input circuits under the grid mode is 120A.

1. Safety Instructions

2. Specifications

General Information

Weight

Protective class

Dimensions

Mounting type

Standard connector

Ingress protection

Warranty description

Maximum # of circuits controlled

Rated system voltage

Max total input current

Short circuit rating

Rated relay module current

Rated Max. DELTA Pro input

DELTA Pro charging power

Max. connected battery energy

Operating and storage temperature range

Enclosure temperature

Touch current

20 lb (9 kg)

500×330×120 mm

Wall Mount

EcoFlow Infinity Port

IP20

5 Years

240V

120A

10kA

6A, 13A, 16A, 20A, 30A

7200W Max (2×3600W)

6800W Max (2×3400W)

21.6 kWh (6×3.6 kWh)

-20°C - 45°C

Less than 65°C

<3.5mA a.c. (Under single fault condition)

1. Multiple sources power this equipment.

2. Electrical equipment should be serviced by authorized personnel only.

3. This equipment is not intended to be used as a service disconnect breaker.

4. Upon losing power, this product automatically switches to the power station.

5. This equipment and downstream load can only be de-energized by opening all upstream

breakers and physically unplugging all DELTA Pros.

DANGER

The SHP can be set up to control a total of 10 load circuits, circuits 1, 3, 5, 7, 9 on the left and 2, 4, 6, 8,

10 on the right. There is a button allowing users to manually reset each circuit relay if there has been

an overcurrent event on the circuit. An indicator lamp on the button turns red if there is a fault in that

circuit.

A lightning bolt indicator for each load circuit is illuminated if that load circuit is energized through one

of the sources (grid or power station).

There are three energization indicators on the SHP, one for the grid, two for the DELTA Pros. If any of

these indicators are illuminated, SHP is energized from that source and, therefore, cannot be opened to

be serviced.

There are two infinity ports on the SHP, which can be either on the bottom of the SHP (default),

or relocated to the front. They connect DELTA Pros to the SHP through the Infinity Cable (one for

each DELTA Pro). Once plugged in, SHP and DELTA Pro will try to establish connection through

communication and SHP’s control circuitry may be powered via DC current from the DELTA pro. Press

the enable button located near the infinity port (labeled “AC 1” or “AC2” to make DELTA Pro ready for

output.

When the DELTA Pro load circuits are energized, an alarm will sound if the front panel cover is opened.

To de-energize the product, all upstream breakers must be opened and both DELTA Pros must be

unplugged.

1. Load Circuit Control Board

3.1 External Features

2. Grid Indicator and Infinity Port Indicator

3. Infinity Port and Enable Button

4. Panel Open Alarm System

3. Product Details

This button can be used to turn on the Bluetooth hotspot for 5 minutes for the user to connect.

This indicator is normally off if no fault is present inside the SHP. It will turn red if there is a fault in

the product. Users can go to the app for a fault diagnostic report. If there is an issue, please contact

customer support for assistance.

5. IOT Reset Button and Indicator

6. Error Indicator

The pause button will physically isolate the 10 load circuits and lock out both connected DELTA Pros.

A signal from the SHP will tell the DELTA Pros to stop outputting power. Please note that this does not

substitute for a service disconnect, nor does it substitute for the de-energization procedure required

before servicing.

This is the only “quick disconnect” that can be used to manually cut all power in an emergency.

AC in and Pro in still energize.

7. Power Station Pause/Resume Button

3.2 Internal Features

NOTE

1. Output Wire Connectors

2. Communication Ports connecting to the key panel

3. Relay Modules

These are the wire connectors for output hot wires going to the load.

The relay modules are available in different current ratings, 6A, 13A, 16A, 20A, and 30A. These

modules contain two relays for each circuit as well as an overcurrent protection fuse. Each module can

be individually replaced without affecting other circuits. De-energize the SHP before replacing any

module.

4. DELTA Pro Wire Connectors

5. Infinity Ports

6. Cooling Fan

7. Ground Bus Bar

8. Input Wire Connectors

9. Switching Connector

These are wire connectors for DELTA Pro. There is one hot wire and one neutral wire required for each

DELTA Pro. At least one neutral wire must be connected to the main panel even if no DELTA Pro is

used. This neutral is used as a return path for DELTA Pro to power your circuits.

Infinity ports can be installed either on the front or the bottom of the product. Users can choose to

switch the position of the Infinity ports. This can improve cable management in tight quarters.

The cooling fan is activated under extreme operating conditions to reduce the ambient temperature

inside of the unit.

This is the ground bus bar, which should be connected to the ground bus bar in the main electrical

panel. The panel casing is connected to this ground. NOTE: Please follow local code requirements with

regard to bonding neutral and ground. Bonding should be done at the first means of disconnect, which

is the service panel, NOT the SHP.

These are the wire connectors for hot wires coming from the circuit breakers in your main panel.

Please keep the connector plugged in its original place, otherwise, if it's unplugged, the power station

connected to Pro 1 will only provide energy to circuits 1, 3, 5, 7, and 9, whereas the power station

connected to Pro 2 will only provide energy to circuits 2, 4, 6, 8, 10.

4. What’s in the Box

Smart Home Panel

Product User Manual Product Installation

Manual

Wall mounting brackets

A bag of accessoriesInfinity Cable and

Wires

The AWM wires can be removed from the harness plugs and replaced with an appropriate length

and type of cable.

NOTE

5. Installation SOP Checklist

No. Checklist Status

Before installation- Project information

Determine the installation location. The Smart Home Panel is rated to IP20,

therefore, it needs to be installed away from direct sunlight, rain, snow and

moisture.

2Determine the distance between the SHP and main electrical panel.

3Confirm the number of loads to be connected to SHP. You can connect up to

10 single pole load circuits.

Determine whether the upstream circuit breakers of the selected loads

require AFCI or GFCI protection. This can be accomplished with an on-site

inspection or photo or video of the panel from the end user.

Determine and gather required materials. SHP can support up to 1 1/2 inch

conduit via five knockouts. Ensure that necessary adjustment factors (for

number of conductors) are accounted for and that wire ampacity is sized

appropriately. For longer runs it is recommended that you use separate

conduits for the input and output wires. For AFCI and GFCI breakers, an

additional standard overcurrent trip breaker is required. For circuits where

AFCI protection is required, metal conduit or whip to the SHP from the main

panel is required. An external AFCI enclosure (available from EcoFlow) to

house AFCI breakers is also required downstream of the SHP.

During installation - Circuit breaker and relay module

1The current rating of relay module must match the upstream circuit breaker.

Failure to do so may cause overcurrent protection to fail.

2The ampacity rating of wiring used should match the circuit current. Using an

undersized cable may cause overheating and even a fire.

3All upstream breakers should be non-GFCI/AFCI. Any AFCI/GFCI breakers

need to be moved downstream of the SHP using an optional accessory box.

During installation - Wiring

1Each load circuit AC input should be connected to the hot wire.

Install the relay modules in the corresponding places and secure by tightening

the screws. Failure to do so may cause the relay module to come loose, which

will produce an error and disconnection of the load channel, as well as risk

overheating and fire.

During installation - Check wiring

1With a multimeter in continuity setting, confirm that the hot wire in of each

SHP channel is not shorted to neutral.

2With a multimeter in continuity setting, confirm that the hot wire in of each

SHP channel is not shorted to ground.

Commissioning

1Make sure the power stations are enabled and that the stop button is off

(raised).

2Close the upstream breaker of DELTA Pro and energize the DELTA Pro AC

Input channel. The grid indicator (white) will turn on if there is no fault.

3Turn each branch circuit breaker back on one by one and check the indicator

status of each channel and power indicator. The indicators will stay white.

If you haven’t done so already, download the EcoFlow App from Google

Play or the App Store and create an EcoFlow account. Open the app on your