Oral-B Genius 8000 Manual de usuario

Marca: Oral-B

Modelo: Genius 8000

Categoría: Cepillos de dientes eléctricos

Tipo: Manual de usuario

Este manual también es adecuado para

English 6

Español 16

Français 27

Internet:

www.oralb.com

www.oralb.ca

www.braun.com

www.service.braun.com

Braun GmbH

Frankfurter Strasse 145

61476 Kronberg

Germany/Alemania/Allemagne

Charger Type 3757

Handle Type 3765

Travel Case Type 3760

Smart Plug Type 492-5214

Tipo de cargador 3757

Tipo de mango 3765

Tipo de estuche portátil 3760

Tipo de enchufe inteligente 492-5214

Type de chargeur 3757

Type de manche 3765

Type d’étui de voyage 3760

Type de prise intelligente 492-5214

90761125/IV-16

EN/E/F

IMPORTANT SAFEGUARDS

Your Oral-B® toothbrush has been carefully designed to offer you and your family a unique

brushing experience that is both safe and effective.

When using electrical products, especially when children are present, basic safety precautions

should always be followed, including the following:

Read all instructions before using.

DANGER

In order to reduce the risk of electrocution:

1. Do not use while bathing.

2. Do not place or store the charger, smart plug or charging travel case where it can fall or be pulled into

a tub or sink.

3. Do not place the charger, smart plug or charging travel case in water or other liquid.

4. Do not reach for a charger, smart plug or charging travel case that has fallen into water. Unplug

immediately.

WARNING

To reduce the risk of burns, electrocution, fire or injury:

1. Close supervision is necessary when this product is used by, on, or near children or persons with

disabilities.

2. Use this product only for its intended use as described in this manual. Do not use attachments not

recommended by the manufacturer.

3. Keep cord away from heated surfaces.

4. Never drop the appliance or insert any object into any opening of the appliance.

5. Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been

dropped or damaged or if it has been dropped into water. If any of these occur, please contact a

service center and return the product for examination and repair.

6. Do not use on self when drowsy or on another who is drowsy or sleeping.

7. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is

being administered.

IMPORTANT

1. Periodically check the entire product/cords/accessories for damage. A damaged or non-functioning

unit should no longer be used. If the product/cords/accessories are damaged, take it to an Oral-B

Service Center.

2. If the toothbrush handle is dropped, the brush head should be replaced before the next use even if no

damage is visible.

3. Do not touch the power plug with wet hands. This can cause an electric shock.

4. When unplugging, always hold the power plug instead of the cord.

5. Do not modify or repair the product. This may cause fire, electric shock or injury. Consult your dealer

for repairs or contact an Oral-B Service Center.

6. The appliance has no user serviceable parts. Do not open and dissemble device except when

disposing of the battery. Follow handling and disposal instructions of the battery/device described in

this manual.

7. Usage by children under age 3 is not recommended.

8. This toothbrush is a personal care device and is not intended for use on multiple patients in a dental

practice or institution.

9. Replace brush (head) every 3 months or sooner if brush head becomes worn.

10. The charging travel case is provided with a special cord set (smart plug), which has an integrated

Safety Extra Low Voltage power supply. Do not exchange or tamper with any part of it, otherwise

there is risk of an electric shock. Only use the special cord set provided with your appliance.

CAUTION

If you are undergoing treatment for any oral care condition, consult your dental professional prior to use.

SAVE THESE INSTRUCTIONS

English

Important Information

• Your Oral-B toothbrush can be used with your

smartphone (find details under «Connecting your

toothbrush to your Smartphone»).

• To avoid electromagnetic interference and/or

compatibility conflicts, deactivate the radio

transmission of your toothbrush handle (5) before

using it in restricted surroundings, such as aircrafts

or specially marked areas in hospitals.

• Deactivate radio transmission by simultaneously

pressing the on/off (3) and mode button (4) for 2

seconds until the radio transmission display (7)

goes off. Follow the same procedure to reactivate

transmission again.

• Persons with pacemakers should always keep the

toothbrush more than six inches (15 centimeters)

from the pacemaker while turned on. Anytime you

suspect interference is taking place, deactivate the

radio transmission of your handle.

Description

1 Brush head

2 Smart Ring

3 On/off button

4 Brushing mode button

5 Handle

6 Brushing mode display

7 Radio transmission display (with Bluetooth®

wireless technology)

8 Charge level display

9 Charging unit (basic charger and brush head

compartment with protective cover)

10 Smartphone holder (depending on model)

10a Holding brackets

10b Lever arm

10c Pull tab

10d Suction cup

11 Charging travel case (depending on model)

11a Charge indicator light

11b USB port

11c Smart plug port

11d Inner lid (with smartphone holder)

11e Removable inlay

12 Smart plug (depending on model)

Specifications

For voltage specifications refer to the bottom of the

charging unit.

Noise level: 68 dB(A)

First use – Connecting

and charging

Prior to first use, you may briefly place the handle (5) on

the plugged-in charging unit (9) to activate it. Once the

charge level display (8) illuminates, it is ready for use.

Note: In case battery is empty (no lights illuminated on

charge level display), charge at least for 30 minutes.

Charging and operating information

Your toothbrush has a waterproof handle, is electrically

safe and designed for use in the bathroom.

• To charge the handle (5), place it on the plugged-in

charging unit (9). The charge level is indicated on the

charge level display (8). The flashing lights indicate

that the handle is charging (picture ➀); once it is fully

charged, the lights turn off. A full charge takes about

12 hours and enables up to 12 days of regular

brushing (twice a day, 2 minutes). Note: At a very

low charge level, the lights might not flash

immediately; it can take up to 10 minutes.

• If the battery is running low, a red light is flashing on

the charge level display and the motor is reducing its

speed. Once the battery is empty, the motor will stop;

it will need at least a 30-minute charge for one usage.

• You can always store the handle on the plugged-in

charging unit to maintain it at full power; a battery

overcharge is prevented by device.

Note: Store handle at room temperature for optimal

battery maintenance.

Caution: Do not expose handle to temperatures

higher than 50°C.

Using your toothbrush

Brushing technique

Wet brush head and apply any kind of toothpaste. To

avoid splashing, guide the brush head to your teeth

before switching on the handle (picture ➁). When

brushing your teeth with one of the Oral-B oscillating-

rotating brush heads guide the brush head slowly

from tooth to tooth, spending a few seconds on each

tooth surface (picture ➂). When using the Oral-B «Deep

Sweep» brush head place the toothbrush bristles

against the teeth at a slight angle towards the gumline.

Apply light pressure and start brushing in back and

forth motions, just like you would do with a manual

toothbrush.

With any brush head start brushing the outsides, then

the insides and finally the chewing surfaces. Brush all

four quadrants of your mouth equally. You may also

consult your dentist or dental hygienist about the right

technique for you.

In the first days of using any electric toothbrush, your

gums may bleed slightly. In general, bleeding should

stop after a few days. Should it persist after 2 weeks,

please consult your dentist or dental hygienist. If you

have sensitive teeth and/or gums, Oral-B recommends

using the «Sensitive» mode (optional in combination

with an Oral-B «Sensitive» brush head).

Smart Ring features

Your toothbrush is equipped with a Smart Ring (2) that

has various functionalities indicated via different colors

of light:

White (default) = Operating and visual timer light

(choose individual color via Oral-B™ app settings)

Red = Pressure sensor light

Blue = Bluetooth® pairing indicator

Timer

You can choose between «Professional» or «2-Minute»

timer.

The «2-Minute» timer signals with a long stuttering

sound and a flashing light of the Smart Ring (2) that the

professionally recommended 2-minute brushing time

has been reached.

The «Professional» timer signals with a short stuttering

sound and a flashing light of the Smart Ring at

30-seconds intervals to move to the next quadrant of

your mouth (picture ➂). A long stuttering sound and a

flashing light indicate the end of the professionally

recommended 2-minute brushing time.

The timer memorizes the elapsed brushing time, even

when the handle is briefly switched off during brushing.

The timer resets if pausing longer than 30 seconds,

briefly pressing the mode button (4) during pause or

placing the handle on the plugged-in charger.

Note: During the use of special Oral-B™ app features,

the visual timer light may be deactivated.

Timer setup:

Your toothbrush comes with the «Professional» timer

activated. To change this, press and hold the mode

button (4) for 2 seconds. Toggle between timer

selection by pressing the on/off button (3). Confirm

selection by pressing the mode button.

• 2 LED’s illuminated indicate «2-Minute» timer

• 4 LED’s illuminated indicate «Professional» timer

Note: You can also set/advance the timer functionality

via Oral-B™ App.

Pressure sensor

If you put excessive pressure on your teeth, the Smart

Ring (2) will light up in red and the motor speed will be

reduced in «Daily Clean», «Pro Clean» and «Sensitive»

mode (picture ➂). Periodically check the operation of

the pressure sensor by pressing moderately on the

brush head during use.

Brushing modes (depending on model)

Your toothbrush offers different brushing modes

indicated on the brushing mode display (6) on your

handle («Daily Clean» mode does not illuminate on the

brushing mode display):

«Daily Clean»

– Standard mode for daily mouth

cleaning

«Pro Clean»

– For an extraordinary clean

feeling (operated with a higher

frequency)

«Sensitive»

– Gentle, yet thorough cleaning

for sensitive areas

«3D White»

– Polishing for occasional or

everyday use

«Gum Care»

– Gentle massage of gums

«Tongue Clean» – Tongue cleaning for occasional

or everyday use

When operating the «Tongue Clean» mode, we

recommend using the «Sensitive» brush head. You can

brush your tongue either with or without toothpaste.

Brush the whole area of your tongue systematically in

gentle movements. The recommended brushing time is

20 seconds; indicated with a flashing light of the Smart

Ring.

Your toothbrush automatically starts in the mode

selected last. To switch to other modes, successively

press the mode button during use (picture ➃). To return

from any mode back to «Daily Clean» mode, press and

hold the mode button (4).

Note: You can also set/advance the mode functionality

via Oral-B™ App.

Brush heads

Oral-B offers you a variety of different Oral-B brush

heads that fit your Oral-B toothbrush handle.

Our oscillating-rotating brush heads can be used for

tooth-by-tooth precision cleaning.

Oral-B CrossAction brush head

Our most advanced brush head. Angled

bristles for a precise clean. Lifts and

powers away plaque.

Oral-B FlossAction brush head

features micropulse bristles that allow for

an outstanding plaque removal in the

interdental areas.

Oral-B 3D White brush head

features a special polishing cup to

naturally whiten your teeth. Please note

that children under 12 years old should

not use the Oral-B «3D White» brush

head.

Oral-B Sensitive brush head

features an extra soft bristle structure

that is gentle on teeth and gums.

Our dynamic «Deep Sweep» brush head can be used

with all common brushing techniques.

Oral-B Deep Sweep brush head

features triple zone cleaning action for

outstanding plaque removal, even in

between teeth.

Oral-B brush heads feature light blue INDICATOR®

bristles to help you monitor brush head replacement

need. With thorough brushing, twice a day for two

minutes, the blue color will fade halfway approximately

within 3 months, indicating the need to exchange your

brush head. If the bristles splay before the color

recedes, you may exert too much pressure on teeth

and gums.

We do not recommend using the Oral-B «FlossAction»

or Oral-B «3D White» brush head with braces. You may

use the Oral-B «Ortho» brush head, specifically

designed to clean around braces and wires.

Connecting your

toothbrush to your

Smartphone

The Oral-B™ App is available for mobile devices

running iOS or Android operating systems. It can be

downloaded for free from App Store

or Google

Play™.

The Oral-B™ App gives you the opportunity to chart

your brushing progress and customize your toothbrush

settings (for many more benefits see the Oral-B™ App

instructions).

• Start the Oral-B™ App. The app will guide you

through the entire Bluetooth pairing procedure.

Note: Oral-B™ App functionality is limited if

Bluetooth wireless technology is deactivated on

your smartphone (for directions please refer to your

smartphone’s user manual).

• Any app instructions will be displayed on your

smartphone.

• If Bluetooth wireless technology is activated on your

handle, the Bluetooth symbol on the radio

transmission display (7) illuminates. Once the handle

is paired, the Smart Ring (2) flashes briefly.

• Keep your smartphone in close proximity (within

5m/16ft distance) when using it with the handle.

Make sure the smartphone is safely positioned in a

dry place.

Note: Your smartphone must support Bluetooth 4.0 (or

higher)/Bluetooth Smart in order to pair your handle.

Cleaning

recommendations

After brushing, rinse your brush head under running

water with the handle switched on. Switch off and

remove the brush head. Clean handle and brush head

separately; wipe them dry before reassembling. Unplug

the charging unit before cleaning. Brush head

compartment and protective cover are dishwasher-

safe. Basic charger should be cleaned with a damp

cloth only (picture ➄).

Accessories

Smartphone Holder

• Before each use, make sure mirror, suction cup

surface (10d) and holding brackets (10a) are always

clean and dry (picture A1). Press your smartphone

holder (10) gently, centered at nose level on the

mirror. Then mount the holder by carefully pressing

the lever arm (10b) towards the mirror until it snaps

in (picture A2).

Note: Only affix on mirror to ensure safe and correct

conditions. For use in bathroom only. Do not use in

automobiles.

• Always make sure the smartphone holder is

securely mounted on the mirror before inserting

your smartphone. Place your smartphone (portrait)

sideways in between the holding brackets (10a) by

pressing against one bracket with your phone and

sliding the other bracket to the side (picture A2).

Follow the same procedure to remove your phone

again.

• Adjust the overall position for the required angle by

moving the ball joint of the holder (picture A3).

Instructions for the best angle will be given via app.

• Once done, remove your phone from the holder.

Take off the smartphone holder by flipping the lever

arm back and pulling the tab carefully (picture A4

1./2.). Affix smartphone holder with each use again.

• The smartphone holder should be cleaned with a

damp cloth only. Store in clean and dry place. If not

in use, always remove your smartphone from the

holder.

Note: Smartphone width required for usage:

minimum 58mm (2.28 in), maximum 83mm (3.27 in).

Caution: Small parts may come off, keep out of

reach of children.

Charging Travel Case

• To charge your handle (5) place it on the pin in the

charging travel case (11) and connect it to an

electric outlet, using the extra smart plug (12)

provided.

• The flashing light (11a) of the charging travel case

indicates that the handle is charging. Once the

handle is fully charged the light turns off. A full

charge can take up to 12 hours (picture B1).

Note: You may use the USB port (11b) to charge an

electric device while the charging travel case is

plugged in. The handle can only be charged with the

smart plug (12)/(11c) not via USB port.

• The inner lid of the travel case has a built-in

smartphone holder (11d), which can hold your

smartphone while using (picture B2). Before use,

make sure your phone fits the stand and keeps

stable.

• The removable inlay (11e) of the travel case is

dishwasher-safe (picture B3/➄). The outer case

should be cleaned with a damp cloth only. Make

sure that travel case parts are completely dry before

reassembling and toothbrush/brush heads are dry

before storing in the travel case.

Note: Clean stains on travel case surface

immediately. Store travel case in a clean and dry

place.

Subject to change without notice.

Environmental Notice

Product contains batteries and/or recyclable

electric waste. For environment protection

do not dispose in household waste, but for

recycling take to electric waste collection

points provided in your country.

Battery removal at the

end of the product’s

useful life

Do not disassemble the product except when

disposing of the battery. Run down battery before

removing. When taking out the battery for disposal, use

protective clothing (gloves, safety glasses, etc.) to omit

skin contact whilst leaking batteries. Use caution not to

short the positive (+) and negative (–) terminals. Insulate

terminals (e.g. with tape) and put the battery in a plastic

bag for disposal.

Open the handle as shown, remove the battery and

dispose of it according to local environmental

regulations.

Caution! Opening the handle will destroy the

appliance and invalidate the warranty.

Information

Bluetooth® radio module

Although all indicated functions on the Bluetooth

device are supported, Oral-B does not ensure 100%

reliability in connection, and feature operation

consistency.

Operation performance and connection reliability are

direct consequences of each individual Bluetooth

device, software version, as well as the operating

system of those Bluetooth devices and company

security regulations implemented on the device.

Oral-B adheres to and strictly implements the

Bluetooth standard by which Bluetooth devices can

communicate and function in Oral-B toothbrushes.

However, if device manufacturers fail to implement this

standard, Bluetooth compatibility and features will be

further compromised and the user may experience

functional and feature-related issues. Please note that

the software on the Bluetooth device can significantly

affect compatibility and operation.

1) Warranty – Exclusions and Limitations

This limited warranty applies only to the new products

manufactured by or for The Procter & Gamble

Company, its Affiliates or Subsidiaries (“P&G”) that can

be identified by the Braun/Oral-B trademark, trade

name, or logo affixed thereto. This limited warranty

does not apply to any non-P&G product including

hardware and software. P&G is not liable for any

damage to or loss of any programs, data, or other

information stored on any media contained within the

product, or any non-P&G product or part not covered

by this limited warranty. Recovery or reinstallation of

programs, data or other information is not covered

under this limited warranty.

This limited warranty does not apply to (i) damage

caused by accident, abuse, misuse, neglect,

misapplication, or non-P&G product; (ii) damage

caused by service performed by anyone other than

Braun or authorized Braun service location; (iii) a

product or part that has been modified without the

written permission of P&G, and (iv) damage arising out

of the use of or inability to use the Oral-B Smartphone

stand/puck, Smartphone mirror holder, or charging

travel case (“Accessories”).

2) Using your smartphone holder

The Oral-B Accessories included in the package has

been designed to provide you with a convenient way to

position your smartphone while you are using the

Oral-B app. Try multiple orientations of your

smartphone in the Oral-B smartphone holder prior to

use to determine the best positioning of your

smartphone in the holder. Be sure to try this in a

manner which will not harm your smartphone if it falls

out of the stand. Do not use in automobiles.

LIMITATION OF LIABILITY

TO THE EXTENT PERMITTED BY APPLICABLE LAW,

IN NO EVENT SHALL P&G, ITS DISTRIBUTORS OR

SUPPLIERS BE LIABLE TO YOU OR ANY THIRD

PARTY FOR ANY DIRECT, INDIRECT, INCIDENTAL,

CONSEQUENTIAL, SPECIAL, EXEMPLARY OR

PUNITIVE DAMAGES, OF ANY NATURE

WHATSOEVER, ARISING OUT OF THE USE OF OR

INABILITY TO USE THE ORAL-B ACCESSORIES,

INCLUDING, WITHOUT LIMITATION, INJURY TO

PERSONS, PROPERTY DAMAGE, LOSS OF VALUE OF

ANY THIRD PARTY PRODUCTS THAT ARE USED IN

OR WITH THE ORAL-B ACCESSORIES, OR LOSS OF

USE OF THE ORAL-B ACCESSORIES OR ANY THIRD

PARTY PRODUCTS THAT ARE USED IN OR WITH THE

ORAL-B ACCESSORIES, EVEN IF P&G HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

WITHOUT LIMITING THE FOREGOING, YOU

UNDERSTAND AND AGREE THAT P&G HAS NO

LIABILITY FOR ANY DAMAGE OR DESTRUCTION TO

CONSUMER ELECTRONICS DEVICES OR OTHER

PERSONAL PROPERTY THAT ARE CONTAINED ON

OR EXTERIOR TO THE ORAL-B ACCESSORIES, OR

ANY LOSS OF DATA CONTAINED IN THE FOREGOING

DEVICES. IN NO EVENT SHALL ANY RECOVERY

AGAINST ORAL-B EXCEED THE ACTUAL PRICE PAID

FOR THE PURCHASE OF THE PRODUCT.

Warranty replacement brush heads

Oral-B warranty will be voided if electric rechargeable

handle damage is found to be attributed to the use of

non-Oral-B replacement brush heads.

Oral-B does not recommend the use of non Oral-B

replacement brush heads.

• Oral-B has no control over the quality of non-Oral-B

replacement brush heads. Therefore, we cannot

ensure the cleaning performance of non-Oral-B

replacement brush heads, as communicated with

the electric rechargeable handle at time of initial

purchase.

• Oral-B cannot ensure a good fit of non-Oral-B

replacement brush heads.

• Oral-B cannot predict the long-term effect of

non-Oral-B replacement brush heads on handle

wear.

All Oral-B replacement brush heads carry the Oral-B

logo and meet Oral-B’s high quality standards. Oral-B

does not sell replacement brush heads or handle parts

under any other brand name.

Satisfaction Guaranteed

or Your Money Back!

Try Oral-B for 60 days, starting from the first day of

purchase. If you are not 100% satisfied, receive a full

refund via pre-paid card. No questions asked. Please

return your product along with your name, address,

contact phone number and the original cash register

receipt indicating purchase price and date to the

address below to receive a pre-paid card in the amount

of your purchase (refunds in Canada include tax and

Canada 1st class mail postage).

U.S. only: Oral-B 60 Day Satisfaction Guaranteed

4608 Appliance Drive Suite 2

Belcamp, MD 21017

Canada only: Attention: 60-Day Challenge Braun MBG

PO Box 12060

Saint John, NB E2L 5E7

Your Oral-B toothbrush must be returned in its original

packaging and be postmarked no later than 60 days

after the date of purchase. Please allow 6-8 weeks for

handling. In the U.S., the shipment return costs of the

product is the responsibility of the consumer. Sorry: No

refunds will be made for any Oral-B product damaged

by accident, neglect, unreasonable use or lost in the

post.

Terms and conditions apply. For further details please

contact our customer service.

Trouble Shooting

Problem Possible reason Remedy

APP

Handle does not

operate (properly)

with Oral-B™ app.

1. Oral-B™ App is turned off.

2. Bluetooth interface is not

activated on smartphone.

3. Radio transmission is

deactivated on handle;

radio transmission display

(7) is turned off.

4. Bluetooth connection to

smartphone has been lost.

5. Your smartphone does not

support Bluetooth 4.0 (or

higher)/Bluetooth Smart.

6. Handle on plugged-in

charger.

1. Turn on Oral-B™ App.

2. Activate Bluetooth interface on smartphone

(described in its user manual).

3. Activate radio transmission by simultaneously

pressing on/off (3) and mode button (4) for 2

seconds until radio transmission display (7) turns on.

4. Pair handle and smartphone again via app settings.

Keep your smartphone in close proximity when

using it with handle.

5. Your smartphone must support

Bluetooth 4.0 (or higher)/Bluetooth Smart in order to

pair handle.

6. Radio transmission is deactivated while handle is

placed on plugged-in charger.

Reset to factory

settings.

Original functionality wanted. Press and hold on/off button (3) for 10 seconds until all

indicator lights double blink simultaneously.

TOOTHBRUSH

Handle is not

operating (during

first use).

1. Handle has not been

activated.

2. Battery has a very low

charge level; no lights

illuminate.

1. Briefly place handle on plugged-in charging unit. It

may take up to 10 min., until charge level display (8)

flashes.

2. Charge at least for 30 min.

Handle does not

operate with

existing SmartGuide

in household.

1. Synchronizing with existing

SmartGuide failed.

2. Radio transmission is

deactivated; radio

transmission display (7) is

turned off.

3. SmartGuide is not

compatible with handle.

4. Two handles are already

assigned to SmartGuide.

5. Function is deactivated via

App feature.

1. Synchronize (existing) handle(s) (again) via

SmartGuide settings in SmartGuide’s battery

compartment: Press «h/min» for 3 seconds. Turn on

handle that you want to synchronize. Then turn on

second handle you want to synchronize. Press

«h/min» or «set» to exit synchronization mode.

2. Activate radio transmission by simultaneously

pressing on/off (3) and mode button (4) for 2

seconds until radio transmission display (7) turns on.

3. Handle cannot be used with excisting SmartGuide.

4. You can synchronize a total of 2 handles only.

Change handles via SmartGuide settings (see 1.)

5. During use of special App features, transmission to

SmartGuide may be deactivated. You can also

(de)activate any SmartGuide communication via App.

1. Short stuttering

sounds/flashing

light every 30

seconds or after

2 minutes.

2. Handle does not

operate any

timer.

1. «Professional timer» or

«2-Minute timer» activated.

2. Timer has been modified/

deactivated via App.

1. Set your timer to 2-Minute timer (stuttering sounds/

flashing light after 2min); or set your timer to

Professional timer (stuttering sounds/flashing light

every 30 seconds). Follow steps under «Timer

setup».

2. Use App to change timer settings or perform factory

reset (see App Trouble Shootings).

Handle does not

charge and blinks.

Ambient temperature for

charging is out of valid range

(< 0°C and > 60°C).

Recommended ambient temperature for charging is

5°C to 35°C.

FOR USA ONLY

Limited 2-Year Warranty

Oral-B warrants this appliance to be free of defects in material and workmanship for a period of

two years from the date of original purchase at retail. If the appliance exhibits such a defect,

Oral-B will, at its option, repair or replace it without cost for parts and labor. The product must be

carried in or shipped, prepaid and insured (recommended), to an authorized Oral-B Service

Center. Proof of date of original purchase is required. The cost to ship the product to an

authorized Service Center is the responsibility of the consumer, the cost to return the product to

the consumer is the responsibility of Oral-B. This warranty does not cover finishes or normal wear,

nor does it cover damage resulting from accident, misuse, dirt, water, tampering, unreasonable

use, service performed or attempted by unauthorized service agencies, failure to provide

reasonable and necessary maintenance, including recharging, or units that have been modified or

used for commercial purposes.

This appliance is equipped with a Bluetooth Smart approved radio module. Failure to establish a

Bluetooth Smart connection to specific smart phones is not covered under the device guarantee,

unless the Bluetooth radio module of this appliance is damaged. The Bluetooth devices are

warranted by their own manufacturers and not by Oral-B. Oral-B does not influence or make any

recommendations to device manufacturers, and therefore Oral-B does not assume any

responsibility for the number of compatible devices with our Bluetooth systems.

Oral-B reserves the right, without any prior notice, to make any technical modifications or

changes to system implementation of device features, interface, and menu structure changes that

are deemed necessary to ensure that Oral-B systems function reliably.

ALL IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR

FITNESS FOR ANY PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO TWO YEARS

FROM DATE OF ORIGINAL PURCHASE. IN NO EVENT WILL ORAL-B BE RESPONSIBLE FOR

CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so

the above limitation may not apply to you. This warranty gives you specific legal rights, and you

may have other legal rights which vary from state to state.

How to obtain service in the USA

Should this product require service, please call 1-800-566-7252 to be referred to the authorized

Oral-B Service Center closest to you.

To obtain service:

A. Carry the product in to the authorized Oral-B Service Center of your choice or,

B. Ship the product to the authorized Oral-B Service Center of your choice. Pack the product well.

Ship the product prepaid and insured (recommended). Include a copy of your proof of

purchase to verify warranty coverage, if applicable.

To obtain original Oral-B replacement parts and accessories:

Contact an authorized Oral-B Service Center.

Please call 1-800-566-7252 to be referred to the authorized Oral-B Service Center

closest to you.

To order original Oral-B replacement parts and accessories (including replacement brush heads)

by phone: Please call 1-800-566-7252.

To speak to an Oral-B Consumer Service Representative: Please call 1-800-566-7252.

FCC Compliance Statement

This device complies with Part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Section 15.21 Information to user:

Changes or modifications not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

Section 15.105 (b)

Note: This equipment has been tested and found to comply with the Limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

– Consult the dealer or an experienced radio/TV technician for help.

FOR CANADA ONLY

Limited 2-Year Warranty

In the event this appliance fails to function within the specified warranty period because of

defects in material or workmanship, and the consumer returns the unit to an authorized service

center, Braun Canada will, at its option either repair or replace the unit without additional charge

to the consumer. This warranty does not cover any product which has been damaged by

dropping, tampering, servicing performed or attempted by unauthorized service agencies, misuse

or abuse. This warranty excludes units which have been modified or used for commercial

purposes.