Transcripción de documentos

G60 - G100  AVVERTENZE PER L’INSTALLATORE OBBLIGHI GENERALI PER LA SICUREZZA 1) ATTENZIONE! È importante per la sicurezza delle persone seguire attentamente tutta l’istruzione. Una errata installazione o un errato uso del prodotto può portare a gravi danni alle persone. 2) Leggere attentamente le istruzioni prima di iniziare l’installazione del prodotto. 3) I materiali dell’imballaggio (plastica, polistirolo, ecc.) non devono essere lasciati alla portata dei bambini in quanto potenziali fonti di pericolo. 4) Conservare le istruzioni per riferimenti futuri. 5) Questo prodotto è stato progettato e costruito esclusivamente per l’utilizzo indicato in questa documentazione. Qualsiasi altro utilizzo non espressamente indicato potrebbe pregiudicare l’integrità del prodotto e/o rappresentare fonte di pericolo. 6) GENIUS declina qualsiasi responsabilità derivata dall’uso improprio o diverso da quello per cui l’automatismo è destinato. 7) Non installare l’apparecchio in atmosfera esplosiva: la presenza di gas o fumi infiammabili costituisce un grave pericolo per la sicurezza. 8) Gli elementi costruttivi meccanici devono essere in accordo con quanto stabilito dalle Norme EN 12604 e EN 12605. Per i Paesi extra-CEE, oltre ai riferimenti normativi nazionali, per ottenere un livello di sicurezza adeguato, devono essere seguite le Norme sopra riportate. 9) GENIUS non è responsabile dell’inosservanza della Buona Tecnica nella costruzione delle chiusure da motorizzare, nonché delle deformazioni che dovessero intervenire nell’utilizzo. 10) L’installazione deve essere effettuata nell’osservanza delle Norme EN 12453 e EN 12445. Il livello di sicurezza dell’automazione deve essere C+D. 11) Prima di effettuare qualsiasi intervento sull’impianto, togliere l’alimentazione elettrica e scollegare le batterie. 12) Prevedere sulla rete di alimentazione dell’automazione un interruttore onnipolare con distanza d’apertura dei contatti uguale o superiore a 3 mm. È consigliabile l’uso di un magnetotermico da 6A con interruzione onnipolare. 13) Verificare che a monte dell’impianto vi sia un interruttore differenziale con soglia da 0,03 A. 14) Verificare che l’impianto di terra sia realizzato a regola d’arte e collegarvi le parti metalliche della chiusura. 15) L’automazione dispone di una sicurezza intrinseca antischiacciamento costituita da un controllo di coppia. E' comunque necessario verificarne la sogli di intervento secondo quanto previsto dalle Norme indicate al punto 10. 16) I dispositivi di sicurezza (norma EN 12978) permettono di proteggere eventuali aree di pericolo da Rischi meccanici di movimento, come ad Es. schiacciamento, convogliamento, cesoiamento. 17) Per ogni impianto è consigliato l’utilizzo di almeno una segnalazione luminosa nonché di un cartello di segnalazione fissato adeguatamente sulla struttura dell’infisso, oltre ai dispositivi citati al punto “16”. 18) GENIUS declina ogni responsabilità ai fini della sicurezza e del buon funzionamento dell’automazione, in caso vengano utilizzati componenti dell’impianto non di produzione GENIUS. 19) Per la manutenzione utilizzare esclusivamente parti originali GENIUS. 20) Non eseguire alcuna modifica sui componenti facenti parte del sistema d’automazione. 21) L’installatore deve fornire tutte le informazioni relative al funzionamento manuale del sistema in caso di emergenza e consegnare all’Utente utilizzatore dell’impianto il libretto d’avvertenze allegato al prodotto. 22) Non permettere ai bambini o persone di sostare nelle vicinanze del prodotto durante il funzionamento. 23) Tenere fuori dalla portata dei bambini radiocomandi o qualsiasi altro datore di impulso, per evitare che l’automazione possa essere azionata involontariamente. 24) Il transito tra le ante deve avvenire solo a cancello completamente aperto. 25) L’Utente utilizzatore deve astenersi da qualsiasi tentativo di riparazione o d’intervento diretto e rivolgersi solo a personale qualificato. 26) Non mettere in corto circuito i poli delle batterie e non tentare di ricaricarle con alimentatori diversi dalle schede Master o Slave. 27) Non gettare le batterie esauste nei rifiuti ma smaltirle utilizzando gli appositi contenitori per consentirne il riciclaggio. I costi di smaltimento sono già stati pagati dalla casa costruttrice. 28) Tutto quello che non è previsto espressamente in queste istruzioni non è permesso IMPORTANT NOTICE FOR THE INSTALLER GENERAL SAFETY REGULATIONS 1) ATTENTION! To ensure the safety of people, it is important that you read all the following instructions. Incorrect installation or incorrect use of the product could cause serious harm to people. 2) Carefully read the instructions before beginning to install the product. 3) Do not leave packing materials (plastic, polystyrene, etc.) within reach of children as such materials are potential sources of danger. 4) Store these instructions for future reference. 5) This product was designed and built strictly for the use indicated in this documentation. Any other use, not expressly indicated here, could compromise the good condition/operation of the product and/or be a source of danger. 6) GENIUS declines all liability caused by improper use or use other than that for which the automated system was intended. 7) Do not install the equipment in an explosive atmosphere: the presence of inflammable gas or fumes is a serious danger to safety. 8) The mechanical parts must conform to the provisions of Standards EN 12604 and EN 12605. For non-EU countries, to obtain an adequate level of safety, the Standards mentioned above must be observed, in addition to national legal regulations. 9) GENIUS is not responsible for failure to observe Good Technique in the construction of the closing elements to be motorised, or for any deformation that may occur during use. 10) The installation must conform to Standards EN 12453 and EN 12445. The safety level of the automated system must be C+D. 11) Before attempting any job on the system, cut out electrical power and disconnect the batteries. 12) The mains power supply of the automated system must be fitted with an all-pole switch with contact opening distance of 3mm or greater. Use of a 6A thermal breaker with all-pole circuit break is recommended. 13) Make sure that a differential switch with threshold of 0.03 A is fitted upstream of the system. 14) Make sure that the earthing system is perfectly constructed, and connect metal parts of the means of the closure to it. 15) The automated system is supplied with an intrinsic anti-crushing safety device consisting of a torque control. Nevertheless, its tripping threshold must be checked as specified in the Standards indicated at point 10. 16) The safety devices (EN 12978 standard) protect any danger areas against mechanical movement Risks, such as crushing, dragging, and shearing. 17) Use of at least one indicator-light is recommended for every system, as well as a warning sign adequately secured to the frame structure, in addition to the devices mentioned at point “16”. 18) GENIUS declines all liability as concerns safety and efficient operation of the automated system, if system components not produced by GENIUS are used. 19) For maintenance, strictly use original parts by GENIUS. 20) Do not in any way modify the components of the automated system. 21) The installer shall supply all information concerning manual operation of the system in case of an emergency, and shall hand over to the user the warnings handbook supplied with the product. 22) Do not allow children or adults to stay near the product while it is operating. 23) Keep remote controls or other pulse generators away from children, to prevent the automated system from being activated involuntarily. 24) Transit through the leaves is allowed only when the gate is fully open. 25) The user must not attempt any kind of repair or direct action whatever and contact qualified personnel only. 26) Do not short-circuit the poles of the batteries and do not try to recharge the batteries with power supply units other than Master or Slave cards. 27) Do not throw exhausted batteries into containers for other waste but dispose of them in the appropriate containers to enable them to be recycled. Disposal costs have already been paid for by the manufacturer. 28) Anything not expressly specified in these instructions is not permitted. CONSIGNES POUR L'INSTALLATEUR RÈGLES DE SÉCURITÉ 1) ATTENTION! Il est important, pour la sécurité des personnes, de suivre à la lettre toutes les instructions. Une installation erronée ou un usage erroné du produit peut entraîner de graves conséquences pour les personnes. 2) Lire attentivement les instructions avant d'installer le produit. 3) Les matériaux d'emballage (matière plastique, polystyrène, etc.) ne doivent pas être laissés à la portée des enfants car ils constituent des sources potentielles de danger. 4) Conserver les instructions pour les références futures. 5) Ce produit a été conçu et construit exclusivement pour l'usage indiqué dans cette documentation. Toute autre utilisation non expressément indiquée pourrait compromettre l'intégrité du produit et/ou représenter une source de danger. 6) GENIUS décline toute responsabilité qui dériverait d'usage impropre ou différent de celui auquel l'automatisme est destiné. 7) Ne pas installer l'appareil dans une atmosphère explosive: la présence de gaz ou de fumées inflammables constitue un grave danger pour la sécurité. 8) Les composants mécaniques doivent répondre aux prescriptions des Normes EN 12604 et EN 12605. Pour les Pays extra-CEE, l'obtention d'un niveau de sécurité approprié exige non seulement le respect des normes nationales, mais également le respect des Normes susmentionnées. 9) GENIUS n'est pas responsable du non-respect de la Bonne Technique dans la construction des fermetures à motoriser, ni des déformations qui pourraient intervenir lors de l'utilisation. 10) L'installation doit être effectuée conformément aux Normes EN 12453 et EN 12445. Le niveau de sécurité de l'automatisme doit être C+D. 11) Couper l'alimentation électrique et déconnecter la batterie avant toute intervention sur l'installation. 12) Prévoir, sur le secteur d'alimentation de l'automatisme, un interrupteur omnipolaire avec une distance d'ouverture des contacts égale ou supérieure à 3 mm. On recommande d'utiliser un magnétothermique de 6A avec interruption omnipolaire. 13) Vérifier qu'il y ait, en amont de l'installation, un interrupteur différentiel avec un seuil de 0,03 A. 14) Vérifier que la mise à terre est réalisée selon les règles de l'art et y connecter les pièces métalliques de la fermeture. 15) L'automatisme dispose d'une sécurité intrinsèque anti-écrasement, formée d'un contrôle du couple. Il est toutefois nécessaire d'en vérifier le seuil d'intervention suivant les prescriptions des Normes indiquées au point 10. 16) Les dispositifs de sécurité (norme EN 12978) permettent de protéger des zones éventuellement dangereuses contre les Risques mécaniques du mouvement, comme l'écrasement, l'acheminement, le cisaillement. 17) On recommande que toute installation soit doté au moins d'une signalisation lumineuse, d'un panneau de signalisation fixé, de manière appropriée, sur la structure de la fermeture, ainsi que des dispositifs cités au point “16”. 18) GENIUS décline toute responsabilité quant à la sécurité et au bon fonctionnement de l'automatisme si les composants utilisés dans l'installation n'appartiennent pas à la production GENIUS. 19) Utiliser exclusivement, pour l'entretien, des pièces GENIUS originales. 20) Ne jamais modifier les composants faisant partie du système d'automatisme. 21) L'installateur doit fournir toutes les informations relatives au fonctionnement manuel du système en cas d'urgence et remettre à l'Usager qui utilise l'installation les "Instructions pour l'Usager" fournies avec le produit. 22) Interdire aux enfants ou aux tiers de stationner près du produit durant le fonctionnement. 23) Eloigner de la portée des enfants les radiocommandes ou tout autre générateur d'impulsions, pour éviter tout actionnement involontaire de l'automatisme. 24) Le transit entre les vantaux ne doit avoir lieu que lorsque le portail est complètement ouvert. 25) L'Usager qui utilise l'installation doit éviter toute tentative de réparation ou d'intervention directe et s'adresser uniquement à un personnel qualifié. 26) Ne pas mettre en court-circuit les pôles des batteries et ne pas tenter de les recharger avec d'autres platines d'alimentation que les platines Maître ou Esclave. 27) Ne pas jeter les batteries épuisées à la poubelle, mais les éliminer dans les conteneurs spécifiques pour le recyclage. Les coûts d'élimination des déchets ont déjà été payés par le constructeur. 28) Tout ce qui n'est pas prévu expressément dans ces instructions est interdit. ADVERTENCIAS PARA EL INSTALADOR REGLAS GENERALES PARA LA SEGURIDAD 1) ATENCION: Es sumamente importante para la seguridad de las personas seguir atentamente las presentes instrucciones. Una instalación incorrecta o un uso impropio del producto puede causar graves daños a las personas. 2) Lean detenidamente las instrucciones antes de instalar el producto. 3) Los materiales del embalaje (plástico, poliestireno, etc.) no deben dejarse al alcance de los niños, ya que constituyen fuentes potenciales de peligro. 4) Guarden las instrucciones para futuras consultas. 5) Este producto ha sido proyectado y fabricado exclusivamente para la utilización indicada en el presente manual. Cualquier uso diverso del previsto podría perjudicar el funcionamiento del producto y/o representar fuente de peligro. 6) GENIUS declina cualquier responsabilidad derivada de un uso impropio o diverso del previsto. ) No instalen el aparato en atmósfera explosiva: la presencia de gas o humos inflamables constituye un grave peligro para la seguridad. 8) Los elementos constructivos mecánicos deben estar de acuerdo con lo establecido en las Normas EN 12604 y EN 12605. Para los países no pertenecientes a la CEE, además de las referencias normativas nacionales, para obtener un nivel de seguridad adecuado, deben seguirse las Normas arriba indicadas.  ENGLISH ENGLISH AUTOMATIC SYSTEM G60 - G100 These instructions apply to the following models: G60 - G100 Automatic systems G60 and G100 allow the automation of sectional, overhead spring-balanced and counterbalanced (with special accessory) doors for residential garages. They consist of an electromechanical operator, electronic control equipment and courtesy light built into a single unit which, fitted to the ceiling, allows door opening by means of a chain or belt transmission. The non-reversing system guarantees mechanical door locking when the motor is not operating, therefore no lock is necessary; a manual release on the inside and one on the outside (optional) allow the door to be moved manually in case of a power failure or malfunction. The operator is equipped with an electronic device that detects any obstacles to door movement. These instructions refer to the operator with chain drive, but the same procedures, adjustments and application limits also apply to the operator with belt drive. The G60 and G100 automatic systems are designed and built for indoor use and for controlling vehicle entry. Any other use is improper. 1. TECHNICAL SPECIFICATIONS 2. DIMENSIONS Door max. height MODEL G60 Power supply (Vac +6 -10% 50Hz) 230 Electric motor (Vdc) 24 Maximum absorbed power (W) 220 Thrust force (N) 600 350 600 1000 Maximum cycles per hour at 20°C 20 Maximum consecutive cycles 6 Minimum distance from ceiling (mm) 35 Courtesy light (Vac-W) 230 - 25 max Courtesy light timer (sec) Carriage speed (load free) (m/min) 120 7,8 Deceleration speed (m/min) Deceleration travel length Dimensions in mm G100 11 1,7 Varies according to setup Intrinsic safety device Tipo 2 Max. overhead door width (mm) 3000 Sectional door max. width (mm) 5000 see useful travel Useful sliding guide travel (mm) 1900 - 2500 - 3100 Protection rating for indoor use only Ambient temperature (°C) -20 ÷ +55 2806 / 3406 / 4006 3. ANCILLARY ELECTRICAL EQUIPMENT 415       328 187 Fig. 1 13 Cable 2 x 0.5 (TX photocell) Cable 4 x 0.5 (RX photocell) Cable 3x0.5 (Radio receiver) Power tubing (230V) Low voltage tubing Cable 2 x 1.5 + earth (power supply) Fig. 2  ENGLISH ENGLISH 4. DESCRIPTION                Ceiling fixture Plastic housing Courtesy light Electronic equipment Motor Operator support Rear connection Operator fixing bracket Sliding guide Drive carriage Release knob Door connection bracket Transmission unit Front connection and chain adjuster Front connection bracket Fig. 3 5. PRELIMINARY CHECKS The door structure must be suitable for automation. In particular, check that the door dimensions conform to those given in the technical specifications and that the door is strong enough. Check the efficiency of the door bearings and joints. Make sure the door moves smoothly; if necessary, clean the guides and lubricate them with silicone-based products (do not use grease). Check correct balancing. Remove the door’s mechanical closing devices so that the door is closed by the automatic system. Check if there is an efficient earth plate for electrical connection of the operator. Make sure there is a clearance of at least 35 mm between the ceiling and the highest sliding point of the door (fig. 4 and 5). With sectional doors, check that the upper guide roller is in the horizontal part of the guide when the door is closed (fig. 6). Fig. 4 Fig. 5 14 Fig. 6  ENGLISH ENGLISH 3) Fit the front connection (fig. 8 ref. B) to the transmission unit (fig. 8 ref. A). 4) Tighten the chain a little by tightening the nut (fig. 8 ref. C). 5) Place the sliding guide on its side (fig. 9) 6) Push the carriage near the drive coupling unit (fig. 9 ref. C). 7) Adjust the tensioner (fig. 9 ref. A) so that the central part of the loop, formed of the upper section of the chain, coincides approximately with middle of the sliding guide (fig. 9 ref. B) Warning: overtightening can damage the transmission unit and drive coupling. 6. ASSEMBLY 6.1. SLIDING GUIDE When using the “two pieces sliding guide”, carry out assembly as described below. If an already assembled guide is available, go to par. 6.2. 1) Assemble the two parts of the sliding guide, inserting them in the central joint (fig. 7 ref. A) up to the metal reference stops (fig. 7 ref. B). 2) Slide the transmission unit all the way along the sliding guide (fig. 8 ref. A) bringing it near the front terminal. 6.2. REAR CONNECTION Fit the rear connection in the special seat on the drive coupling unit (fig. 10). If the operator has to be installed directly in contact with the ceiling, cut or bend the fixing brackets (fig. 10 ref. A) and, in the latter case, remove the cage nut. For fixing, the special holes are used (fig. 10 ref. B). Prepare a shim of approx. 5 mm for inserting between the rear connection and the ceiling. Fig. 7 Fig. 10 Fig. 8 Fig. 9 15  ENGLISH ENGLISH 6.3. OUTSIDE RELEASE DEVICE (optional) When using the outside release device, fit the cable in the seat before starting installation. 1) Release the carriage (see par. 7.4. point 3) and bring it to the slot located on the upper part of the sliding guide. 2) Insert the cable end in the special red seat (fig. 11). 3) Move the carriage back towards the drive coupling unit until the through hole on the carriage matches the slot and insert the unsheathed cable (fig. 12). 4) Pull the cable out from the bottom part of the carriage. 5) Wind the cable around so that it is not a hindrance when installing the sliding guide. 3) Position the front connection fixing bracket with bottom edge at least 5 mm above the intersection point of the lines and centred with the vertical line (fig. 13). See par. 7.2. for correct positioning of the bracket with respect to the connection point on the door. 4) Mark the two fixing points. 5) Drill the holes and proceed with installation. 6) Position the sliding guide on the ground, perpendicular to the door. 7) Lift the guide from the front connection and assemble the connection with the fixing bracket using the special through screw and nut (fig. 14). 7. INSTALLATION For safe work install the operator keeping the door completely closed; use adequate fixing systems and anchorage points and read all of this chapter before carrying out installation. 7.1. SLIDING GUIDE After completing the preliminary assembly operations, install the sliding guide, proceeding as follows: 1) Draw a vertical line on the lintel, corresponding to the centre of the door (fig. 13). 2) Draw a horizontal line on the lintel, corresponding to the max. height reached by the door during movement (see fig. 4 and 5). Fig. 13 Fig. 11 Fig. 12 Fig. 14 16  ENGLISH ENGLISH 8) Lift the sliding guide bringing the rear connection to the same level as the front one, or, with sectional doors, until reaching the same angle as the door horizontal rail. For direct fixing to the ceiling, go to point 12, after modifying the rear connection as indicated in par. 6.2. 9) Measure the distance between ceiling and the centre distance of the rear connection fixing nuts. 10) Bend the brackets (supplied) to the measurement made (measure from the centre of the first slot on the bracket). 11) Fit the brackets on the rear connection and reposition the sliding guide (fig. 15). 12) Mark the fixing points on the ceiling, drill (taking care to protect the sliding guide), position the front fixing bracket of the operator (fig. 10 ref. C and fig. 15) and complete guide installation. 13) If using a “two pieces sliding guide” with central connection (fig. 16 ref. A) or the central support for single rail (fig. 16 ref. B - optional), carry out ceiling fixing using the special brackets, proceeding as described in steps 9,10 and 12 (fig. 16). connection and front connection bracket fixing holes is not more than 20 cm (fig. 18). For correct working of the automatic system avoid arm angles of more than 30° with respect to the sliding guide. If using the curved arm for sectional doors (optional) carry out assembly with the straight arm of the carriage as indicated in fig. 19. To improve the efficiency of the anticrushing system it is advisable to fix the connection bracket on the sectional door in the lowest position possible, but not more than 40 cm from the front connection of the operator. 5) Mark, drill and fix the connection bracket to the door. 7.2. CONNECTION ON DOOR 1) Assemble the connection bracket with the carriage bar (fig. 17). If using the outside release device, position the connection bracket on the door so that the release wire loop is turned towards the left side of the door (fig. 17 and 18). 2) Close the door and bring the carriage near it. 3) Position the connection bracket on the door centred with the middle. 4) Check that the distance between centres of the door Fig. 17 Fig. 18 Fig. 15 Fig. 16 Fig. 19 17  ENGLISH ENGLISH 7.3. OPERATOR After installing the sliding guide, install the operator: 1) Remove the plastic housing. 2) Unscrew the courtesy light. 3) Insert the gear motor shaft in the coupling located in the sliding guide rear connection (fig. 20). 4) Fix the operator to the guide (fig. 21). 7.4. AUTOMATIC SYSTEM RELEASE 1) Establish the height of the release knob and cut off the excess cord. 2) Tie a knot in the end of the cord and assemble the release handle (fig. 22). 3) Pull the release lever downwards and make sure the door can be moved manually (fig. 23). 4) Pull the release handle sideways in the direction of the door (fig. 24). Check that, on releasing the handle, the LOCK window located under the carriage is red. Manually move the door until locating the carriage coupling point. Fig. 22 7.5. OUTSIDE RELEASE If the automatic system is equipped with an outside release device, conclude the installation already started (see par. 6.3.): 1) Cut the cable sheathing to size (fig. 25 ref. A). 2) Insert the cable in the sheath and through the special eyelet of the connection bracket on the door (fig. 25 ref. B). 3) Cut the cable to size and assemble it with the inside lever of the release handle (fig. 25 ref. C). Fig. 23 Fig. 20 Fig. 24 Fig. 21 Fig. 25 18  ENGLISH ENGLISH If the safety devices are activated when the door is locked or open, they prevent it from closing. To install several safety devices, connect the N.C. contacts in series. 8. G60 and G100 ELECTRONIC CARD 8.1. TECHNICAL SPECIFICATIONS 230 Vac 50 Hz Power supply Accessories power supply 24 Vdc Accessories max. load 200 mA Ambient temperature -20° ÷ +55°C Motor protection fuses Quick connector for 5-pin radio-receiver module Function logics Automatic/ Semiautomatic Terminal board connections Open/Stop/Safety devices/Failsafe/Flasher Courtesy light timer 2 min 8.2. 531MPS AND 576MPS CARD COMPONENTS F1 Motor fuse (G60=10A, G100=15A) F2 Accessories protection 0.25A automatic reset J1 Low voltage terminal board for inputs /accessories J2 Quick connector for 5-pin radio-receiver module J3 230V power supply input terminal board J4 Transformer primary connector J5 Courtesy light connector J6 Flashing light output terminal board J7 Transformer secondary connector J8 Motor output connector P1 Open pushbutton P2 Set-up pushbutton TR1 Closing force adjustment (G100 only)) TR2 Opening force adjustment (G100 only) DS1 Programming dip-switches LD1 OPEN input signalling LED LD2 STOP input signalling LED LD3 FSW input signalling LED Fig. 26 N.B.: if safety devices are not connected, jumper connect FSW to the terminal -TX FSW. CONNECTOR J2 (low voltage) Connector J2 is used for quick connection of 5-pin radioreceiver module Insert and remove the cards after disconnecting the power to the operator. TERMINAL BOARD J3 (high voltage) Terminal board for 230Vac 50Hz power supply on the support plate = Earth fixing screw (fig. 27 ref. A). TERMINAL BOARD J6 (high voltage) 230Vac terminal board for connection of flasher. 8.3.2. Programming Dip-Switches DS1 8.3. DESCRIPTION 1 No. Function Failsafe 2 Anticrushing sensitivity 3 Force adjustment (onlyG100) 4 Carriage speed 8.3.1. Terminal boards and connectors TERMINAL BOARD J1 (low voltage) OPEN=Open Command (N.O.) Any device (pushbutton, key selector, etc.) which, by closing a contact, supplies an opening (or closing) pulse to the door. To install several Open devices, connect N.O. contacts in parallel. STOP=Stop command (N.C.) Any device (e.g. a pushbutton) which, by opening a contact, stops door movement. To install several stop devices, connect the N.C. contacts in series. N.B.: if stop devices are not used, jumper connect STOP to the inputs common contact. =Inputs/negative accessories supply common contact. =Accessories supply positive pole (24Vdc 200mA max) FSW= Closing safety devices contact (N.C.) Safety devices are all devices (photocells, sensitive edges, etc.) with N.C. contact which, in case of an obstacle in the area they protect, cut in to reverse door closing movement. OFF Active ON Not active Low High Automatic Manual High Low Failsafe When activated it enables the photocell function test before any movement. Anticrushing sensitivity In the event of doors with an uneven movement, it allows the sensitivity of the anticrushing device to be reduced in order to avoid unwanted activations. Manual adjustment of force (G100 only) To use the manual force adjustment, before carrying out learning turn DS1 switch no.3 to ON and manually adjust the thrust force with TR1 (closing) and TR2 (opening). The max. deliverable force is 1000N. After adjusting, start the learning procedure corresponding to the required operation. If the force is inadequate the learning cycle will not be correctly concluded. The sensitivity of the anticrushing device depends 19  ENGLISH ENGLISH on the set force value: if the value is too low, unwanted interventions of the device could occur, whereas if the value is too high, efficiency will be excessively decreased. Speed adjustment If the door movement is too fast or uneven, the slow carriage speed can be selected. 8.3.3. Courtesy light The courtesy light stays on for 2 minutes from the end of the operation (not modifiable). During the self-learning cycle the lamp flashes rapidly (on for one second every two). In case of an anomaly in the equipment or if the self-learning cycle does not end correctly, the light flashes slowly (on for two seconds every four). 8.4. CONNECTIONS IMPORTANT: Always turn the power off before any intervention on the card (connections, programming, maintenance). The electrical system specifications are given in the chapter “Instructions for the installer”. Always separate power cables from the control cables. To prevent any electrical interference, use separate sheaths. The operator is equipped with a cable with Shuko plug already wired; if using a different cable make sure to connect the earth to the special anchoring point indicated in fig. 27 ref. A. For the cable passage, use the arrangement located on the back of the housing. If tubing is used, execute the slot as shown in fig. 27 ref. B. Carry out the electrical connections, referring to fig. 28. If theSTOP input is not used, jumper connect the input to the terminal . If the photocells are not used, connect the FSW input to the -TX FSW terminal. Input status LEDs DL Meaning On Off Not active Active 1 Input status OPEN 2 Input status STOP Active Not active Input status FSW Safety devices activated Safety devices deactivated 3 The status of automatic system stopped and at rest is indicated in bold-face for each input. Fig. 27 OPEN STOP OTHER SAFETY DEVICES Flashing light 230V~ 50-60Hz 230V~ 50-60Hz 20 Fig. 28  ENGLISH ENGLISH The procedure also determines the operational logic. The logic tables gives the behaviour of the automation in the various conditions and following commands or safety device intervention. Learning can be carried out in automatic or manual mode; in the latter case the deceleration points can be established in opening and closing, whereas in automatic, the equipment independently establishes the movement parameters. If the procedure does not conclude correctly (e.g. due to excessive friction during door movement), the equipment signals the anomaly status (the courtesy light flashes slowly). In this case, the procedure must be repeated after the cause has been eliminated. With the G100 operator it is possible to carry out a learning procedure with thrust of 1000N instead of 600 or use the thrust force manual adjustment. 8.5. PROGRAMMING 8.5.1. Card settings Carry out the equipment settings by means of the Dip-Switch DS1 to obtain the required operation. Max. thrust force can be manually set on the operator G100 by turning the dip-switch 3 of DS1 to ON and adjusting the potentiometers TR1 (closing) and TR2 (opening). 8.5.2. Learning During the learning procedure, the obstacle detection device is not operating. The STOP command and the closing safety devices (FSW) are active; their intervention causes interruption of the learning and anomaly signalling. Refit the courtesy light. The SET-UP cycle can be carried out even with the plastic housing already fitted (fig. 29). To access the programming button, remove the courtesy light ceiling fixture and insert a screwdriver in the special passage (fig. 30). If, on pressing the OPEN pushbutton during the learning phase, the operator does not carry out any movement, check the correct positioning of the housing. If the SET-UP is carried out without the housing fitted, pay maximum attention not to touch live parts and the courtesy light. The learning cycle defines: - the necessary force for moving the door. - deceleration points. - door opening and closing stop points. - pause time (in automatic logic). Learning can be started with the operator blocked, regardless of the door position. AUTOMATIC Logic DOOR STATUS OPEN STOP SAFETY DEVICES CLOSED Opens and closes after the pause time No effect** No effect OPEN FOR PAUSE Restarts pause time count* Stops * Restarts pause time count* CLOSING Reverses motion Stops ** Reverses motion OPENING No effect Stops ** No effect * STOPPED Closes No effect** No effect * SEMIAUTOMATIC Logic DOOR STATUS CLOSED OPEN Open STOP No effect** SAFETY DEVICES No effect OPEN Closes No effect** No effect * Reverses motion Stops ** Reverses motion CLOSING OPENING Locks Stops ** No effect * STOPPED Closes No effect** No effect * * Prevents closing if pulse is maintained ** Prevents closing and/or opening if pulse is maintained AUTOMATIC LEARNING WITH LOGIC “E” (SEMIAUTOMATIC) Press the SET-UP pushbutton for 1 second. The courtesy light starts to flash when the button is released. 1) After 8 seconds the operator automatically does a closing operation until detecting the ground stop. 2) The operator starts the opening movement. Wait until it reaches the opening end travel or effect an OPEN command in the position in which stopping of movement is required. 3) The operator closes the door. 4) Wait until the door reaches the ground stop and the operator stops. If the learning procedure was successful the courtesy light stops flashing and stays on for 5 seconds. During the 5 seconds, in order to reduce the load on the release system, OPEN pulses can be sent within 2 seconds of each other to reverse the carriage. One pulse equals 5 mm travel. N.B.: Carriage reversing is only visible during normal operation of the automatic system. The electronic equipment establishes the deceleration points. Fig. 29 MANUAL LEARNING WITH LOGIC “E” (SEMIAUTOMATIC) Press the SET-UP pushbutton for one second. The courtesy light starts flashing when the button is released. Carry out the following procedure within 8 seconds (otherwise the operator will carry out automatic learning). 1) Effect the 1st OPEN command: the operator carries out a closing operation until detecting the ground stop and stops. 2) Effect the 2nd OPEN command: the operator carries out an opening movement. Fig. 30 21  ENGLISH 3) Effect the 3rd OPEN command to establish the point at which the start of deceleration is required. 4) Effect the 4th OPEN command to establish the point of stopping in opening, or wait until the automatic system detects the opening end travel and stops. 5) Effect the 5th OPEN command: the automatic system starts the closing movement. 6) Effect the 6th OPEN command to establish the point at which the start of deceleration is required. 7) Wait until the door reaches the ground stop and the operator stops. If the learning procedure was successful, the courtesy light stops flashing and remains on for 5 seconds. During these 5 seconds, in order to reduce the load on the release system, OPEN pulses can be sent within 2 seconds of each other to reverse the carriage. A pulse equals 5 mm travel. N.B.: Carriage reversing is only visible during normal operation of the automatic system AUTOMATIC LEARNING WITH LOGIC “A” (AUTOMATIC) Hold down the SET-UP pushbutton until the courtesy light comes on (approx. 5 seconds). On releasing the button the courtesy light starts flashing. 1) After 4 seconds the operator automatically carries out closing until detecting the ground stop. 2) The operator moves the door in opening. Wait until it reaches the opening end travel or effect an OPEN command in the position in which stopping of movement is required. 3) The operator closes the door. 4) Wait until the door reaches the ground stop and the operator stops. If the learning procedure was successful, the courtesy light stops flashing and remains on for 5 seconds. During these 5 seconds, in order to reduce the load on the release system, OPEN pulses can be sent within 2 seconds of each other to reverse the carriage. A pulse equals 5 mm travel. N.B.: Carriage reversing is only visible during normal operation of the automatic system. The electronic equipment establishes the deceleration points. The pause time is set at 3 minutes. MANUAL LEARNING WITH LOGIC “A” (AUTOMATIC) Hold down the SET-UP pushbutton until the courtesy light comes on (approx. 5 seconds). On releasing the button the courtesy light starts flashing. Carry out the following procedure within 4 seconds (otherwise the operator carries out automatic SET-UP). 1) Effect the 1st OPEN command: the operator carries out a closing operation until detecting the ground stop. 2) Effect the 2nd OPEN command: the operator carries out an opening movement. 3) Effect the 3rd OPEN command to establish the point at which the start of deceleration is required. 4) Effect the 4th OPEN command to establish the point of stopping in opening, or wait until the automatic system detects the opening end travel. After stopping, the count of time when the automatic system is left open begins. This is the pause that will be respected in normal operation (max. 3 minutes). 5) Effect the 5th OPEN command: the pause time count is stopped and the closing movement starts. 6) Effect the 6th OPEN command to establish the point at which the start of deceleration is required. 7) Wait until the door reaches the stop and the operator stops. If the learning procedure was successful, the courtesy light stops flashing and remains on for 5 seconds. During these 5 seconds, in order to reduce the load on the release system, OPEN pulses can be sent within 2 seconds of each other to reverse the carriage. A pulse equals 5 mm travel. N.B.: Carriage reversing is only visible during normal operation of automatic system. ENGLISH LEARNING WITH THRUST FORCE 1000N (G100 only) If learning is not carried out correctly due to heaviness of the door or for problems in moving it, learning can be carried out with an increased thrust force (1000N max. thrust instead of 600N). To launch this type of learning: 1) Start the required learning cycle in the usual way. 2) While the automatic system is executing the required movements, repeat the launch of learning procedure. 3) The automatic system starts the learning cycle again, but with increased thrust. MANUAL SETTING OF GROUND STOP During the learning phase, the operator seeks the ground stop using the maximum deliverable force (600N for the G60, 600 or 1000N for the G100). To avoid excessive stress, the stopping point can also be established manually: when the automatic system executes the closing movements, effect an OPEN command when the stop is reached, If the stop commands are incongruous at the first and second closing, the automatic system will signal anomaly status and the learning cycle will have to be repeated. N.B.: at the end of the learning cycle make the automatic system do a complete cycle to allow it to acquire the correct stopping point in closing. After this cycle, if the automation reopens the door again, command its closing. N.B.: The sensitivity of the anticrushing device depends on the programming (anticrushing sensitivity, manual force adjustment) and the mechanical characteristics of the door. After installation and programming, always carry out the checks required by the rules given in the chapter “INSTRUCTIONS FOR THE INSTALLER” of this handbook. PRE-FLASHING The pre-flashing function can be activated and disabled (following an OPEN command, the unit ctivates the flashing lamp for 5 seconds before it starts the movement). Procedure: 1) Press and hold down the SETUP key. 2) Press the OPEN key too after about 3 seconds. If the courtesy lamp goes ON, pre-flashing was activated, if instead, it stays OFF, pre-flashing was disabled. 3) Release both push-buttons. 22  ENGLISH ENGLISH 9. START-UP Check the state of the equipment inputs and make sure all the safety devices are correctly connected (the relevant LEDs must be on). Do a few complete cycles to check correct operation of the automatic system and the accessories connected to it, with particular attention to the safety devices and the operator anticrushing device. Apply the stickers indicating the release device operation, and apply the danger sign in a clearly visible place on the door. Give the customer the “User’s Guide” page, illustrate system operation and the operator release and lock operations indicated in the Guide. 10. MAINTENANCE To ensure trouble-free operation and a constant safety level, an overall check of the system should be carried out every 6 months. A form for recording operations has been included in the “User’s Guide” booklet. Fig. 31 11. REPAIRS For possible repairs, contact authorized Repair Centres. 12. TROUBLESHOOTING GUIDE Fault Possible causes Cure The STOP and FSW safety devices are When starting the learning system the active even during the learning phase.. courtesy light flashes but the automatic Their incorrect connection or non-consystem does not carry out any operation. nection inhibits operator operation. The STOP command is active The automatic system does not perform any movement Check the status of the LEDS, following The Failsafe function is active but the NC the indications given in the “Input LEDs status” tables. Check the connections contact of the devices connected to the FSW input does not open during the given in fig. 28 test performed by the equipment before starting the operation The automatic system opens the door but does not close it The FSW safety devices are activated Check door balancing and make sure it moves without excessive friction. Move the door manually using the door bar The automatic system detects excessive attachment and make sure movement difficulty in door movement is smooth without requiring excessive pushing or pulling. When using operator The automatic system executes frequent G100 learning can be carried out with a reversals of motion during opening and/ thrust force at 1000N or the thrust force or closing can be manually adjusted (see chap. 8.5.) Learning is not correctly terminated and the courtesy light signals an anomaly Automatic system release is difficult with door closed The mechanical load on the release system with door closed is excessive Do a new learning cycle, then reduce the closing thrust commanding carriage reversal as described in par. 8.5.2 The courtesy light signals an anomaly The learning procedure was unsuccessful or (for model G100 only) switch no. 3 of DS1 was moved (automatic/manual force adjustment) and a new learning cycle was not carried out Do a new learning cycle 23  ENGLISH ENGLISH 13. ACCESSORIES Automatic systems G60 and G100 can automate overhead counterbalanced doors using the special accessory (fig. 32) Use of the safety edge with conductive element is facilitated by the possibility of housing the special control unit (fig. 33) on the operator. The outside release device can be installed with lever system (fig. 34 ref. A) or key (fig. 34 ref. B). The central support (fig. 35) offers a central fixing point also for the one-piece sliding guide. For installation, see the instructions for the individual accessories. Fig. 35 Fig. 32 Fig. 33 Fig. 34 24  9) GENIUS no es responsable del incumplimiento de las buenas técnicas de fabricación de los cierres que se han de motorizar, así como de las deformaciones que pudieran intervenir en la utilización. 10) La instalación debe ser realizada de conformidad con las Normas EN 12453 y EN 12445. Elnivel de seguridad de la automación debe ser C+D. 11) Quiten la alimentación eléctrica y desconecten las baterías antes de efectuar cualquier intervención en la instalación. 12) Coloquen en la red de alimentación de la automación un interruptor omnipolar con distancia de apertura de los contactos igual o superior a 3 mm. Se aconseja usar un magnetotérmico de 6A con interrupción omnipolar. 13) Comprueben que la instalación disponga línea arriba de un interruptor diferencial con umbral de 0,03 A. 14) Verifiquen que la instalación de tierra esté correctamente realizada y conecten las partes metálicas del cierre. 15) La automación dispone de un dispositivo de seguridad antiaplastamiento constituido por un control de par. No obstante, es necesario comprobar el umbral de intervención según lo previsto en las Normas indicadas en el punto 10. 16) Los dispositivos de seguridad (norma EN 12978) permiten proteger posibles áreas de peligro de Riesgos mecánicos de movimiento, como por ej. aplastamiento, arrastre, corte. 17) Para cada equipo se aconseja usar por lo menos una señalización luminosa así como un cartel de señalización adecuadamente fijado a la estructura del bastidor, además de los dispositivos indicados en el “16”. 18) GENIUS declina toda responsabilidad relativa a la seguridad y al buen funcionamiento de la automación si se utilizan componentes de la instalación que no sean de producción GENIUS. 19) Para el mantenimiento utilicen exclusivamente piezas originales GENIUS 20) No efectúen ninguna modificación en los componentes que forman parte del sistema de automación. 21) El instalador debe proporcionar todas las informaciones relativas al funcionamiento del sistema en caso de emergencia y entregar al usuario del equipo el manual de advertencias que se adjunta al producto. 22) No permitan que niños o personas se detengan en proximidad del producto durante su funcionamiento. 23) Mantengan lejos del alcance los niños los telemandos o cualquier otro emisor de impulso, para evitar que la automación pueda ser accionada involuntariamente. 24) Sólo puede transitarse entre las hojas si la cancela está completamente abierta. 25) El usuario no debe por ningún motivo intentar reparar o modificar el producto, debe siempre dirigirse a personal cualificado. 26) No pongan en cortocircuito los polos de las baterías y no intenten recargarlas con alimentadores diferentes de las tarjetas Master o Slave. 27) No abandonen las baterías agotadas en el ambiente, hay que eliminarlas utilizando los específicos contenedores para permitir el reciclaje de las mismas. Los costes de eliminación ya han sido pagados por el fabricante. 28) Todo lo que no esté previsto expresamente en las presentes instrucciones debe entenderse como no permitido HINWEISE FÜR DEN INSTALLATIONSTECHNIKER ALLGEMEINE SICHERHEITSVORSCHRIFTEN 1) ACHTUNG! Um die Sicherheit von Personen zu gewährleisten, sollte die Anleitung aufmerksam befolgt werden. Eine falsche Installation oder ein fehlerhafter Betrieb des Produktes können zu schwerwiegenden Personenschäden führen. 2) Bevor Stempel van de dealer:Bevor mit der Installation des Produktes begonnen wird, sollten die Anleitungen aufmerksam gelesen werden. 3) Das Verpackungsmaterial (Kunststoff, Styropor, usw.) sollte nicht in Reichweite von Kindern aufbewahrt werden, da es eine potentielle Gefahrenquelle darstellt. 4) Die Anleitung sollte aufbewahrt werden, um auch in Zukunft Bezug auf sie nehmen zu können. 5) Dieses Produkt wurde ausschließlich für den in diesen Unterlagen angegebenen Gebrauch entwickelt und hergestellt. Jeder andere Gebrauch, der nicht ausdrücklich angegeben ist, könnte die Unversehrtheit des Produktes beeinträchtigen und/oder eine Gefahrenquelle darstellen. 6) Die Firma GENIUS lehnt jede Haftung für Schäden, die durch unsachgemäßen oder nicht bestimmungsgemäßen Gebrauch der Automatik verursacht werden, ab. 7) Das Gerät sollte nicht in explosionsgefährdeten Umgebungen installiert werden: das Vorhandensein von entflammbaren Gasen oder Rauch stellt ein schwerwiegendes Sicherheitsrisiko dar. 8) Die mechanischen Bauelemente müssen den Anforderungen der Normen EN 12604 und EN 12605 entsprechen. Für Länder, die nicht der Europäischen Union angehören, sind für die Gewährleistung eines entsprechenden Sicherheitsniveaus neben den nationalen gesetzlichen Bezugsvorschriften die oben aufgeführten Normen zu beachten. 9) Die Firma GENIUS übernimmt keine Haftung im Falle von nicht fachgerechten Ausführungen bei der Herstellung der anzutreibenden Schließvorrichtungen sowie bei Deformationen, die eventuell beim Betrieb entstehen. 10) Die Installation muß unter Beachtung der Normen EN 12453 und EN 12445 erfolgen. Die Sicherheitsstufe der Automatik sollte C+D sein. 11) Vor der Ausführung jeglicher Eingriffe auf der Anlage sind die elektrische Versorgung und die Batterie abzunehmen. 12) Auf dem Versorgungsnetz der Automatik ist ein omnipolarer Schalter mit Öffnungsabstand der Kontakte von über oder gleich 3 mm einzubauen. Darüber hinaus wird der Einsatz eines Magnetschutzschalters mit 6A mit omnipolarer Abschaltung empfohlen. 13) Es sollte überprüft werden, ob vor der Anlage ein Differentialschalter mit einer Auslöseschwelle von 0,03 A zwischengeschaltet ist. 14) Es sollte überprüft werden, ob die Erdungsanlage fachgerecht ausgeführt wurde. Die Metallteile der Schließung sollten an diese Anlage angeschlossen werden. 15) Die Automation verfügt über eine eingebaute Sicherheitsvorrichtung für den Quetschschutz, die aus einer Drehmomentkontrolle besteht. Es ist in jedem Falle erforderlich, deren Eingriffsschwelle gemäß der Vorgaben der unter Punkt 10 angegebenen Vorschriften zu überprüfen. 16) Die Sicherheitsvorrichtungen (Norm EN 12978) ermöglichen den Schutz eventueller Gefahrenbereiche vor mechanischen Bewegungsrisiken, wie zum Beispiel Quetschungen, Mitschleifen oder Schnittverletzungen. 17) Für jede Anlage wird der Einsatz von mindestens einem Leuchtsignal empfohlen sowie eines Hinweisschildes, das über eine entsprechende Befestigung mit dem Aufbau des Tors verbunden wird. Darüber hinaus sind die unter Punkt “16” erwähnten Vorrichtungen einzusetzen. 18) Die Firma GENIUS lehnt jede Haftung hinsichtlich der Sicherheit und des störungsfreien Betriebs der Automatik ab, soweit Komponenten auf der Anlage eingesetzt werden, die nicht im Hause GENIUS hergestellt wurden. 19) Bei der Instandhaltung sollten ausschließlich Originalteile der Firma GENIUS verwendet werden. 20) Auf den Komponenten, die Teil des Automationssystems sind, sollten keine Veränderungen vorgenommen werden. 21) Der Installateur sollte alle Informationen hinsichtlich des manuellen Betriebs des Systems in Notfällen liefern und dem Betreiber der Anlage das Anleitungsbuch, das dem Produkt beigelegt ist, übergeben. 22) Weder Kinder noch Erwachsene sollten sich während des Betriebs in der unmittelbaren Nähe der Automation aufhalten. 23) Die Funksteuerungen und alle anderen Impulsgeber sollten außerhalb der Reichweite von Kindern aufbewahrt werden, um ein versehentliches Aktivieren der Automation zu vermeiden. 24) Der Durchgang oder die Durchfahrt zwischen den Flügeln darf lediglich bei vollständig geöffnetem Tor erfolgen. 25) Der Betreiber sollte keinerlei Reparaturen oder direkte Eingriffe auf der Automation ausführen, sondern sich hierfür ausschließlich an qualifiziertes Fachpersonal wenden. 26) Die Pole der Batterien sollten nicht kurzgeschlossen werden. Die Batterien sollten nicht mit Speisegeräten geladen werden, die von den Karten Master oder Slave abweichen. 27) Leere Batterien gehören nicht in den Hausmüll, sondern sind über die entsprechenden Behälter zu entsorgen, damit sie dem Recycling zugeführt werden können. Die Entsorgungskosten wurden bereits vom Hersteller bezahlt. 28) Alle Vorgehensweisen, die nicht ausdrücklich in der vorliegenden Anleitung vorgesehen sind, sind nicht zulässig WAARSCHUWINGEN VOOR DE INSTALLATEUR ALGEMENE VEILIGHEIDSVOORSCHRIFTEN 1) LET OP! Het is belangrijk voor de veiligheid dat deze hele instructie zorgvuldig wordt opgevolgd. Een onjuiste installatie of foutief gebruik van het product kunnen ernstig persoonlijk letsel veroorzaken. 2) Lees de instructies aandachtig door alvorens te beginnen met de installatie van het product. 3) De verpakkingsmaterialen (plastic, polystyreen, enz.) mogen niet binnen het bereik van kinderen worden gelaten, want zij vormen een mogelijke bron van gevaar. 4) Bewaar de instructies voor raadpleging in de toekomst. 5) Dit product is uitsluitend ontworpen en gebouwd voor het doel dat in deze documentatie wordt aangegeven. Elk ander gebruik, dat niet uitdrukkelijk wordt vermeld, zou het product kunnen beschadigen en/of een bron van gevaar kunnen vormen. 6) GENIUS aanvaardt geen enkele aansprakelijkheid voor schade die ontstaat uit oneigenlijk gebruik of ander gebruik dan waarvoor het automatische systeem is bedoeld. 7) Installeer het apparaat niet in een explosiegevaarlijke omgeving: de aanwezigheid van ontvlambare gassen of dampen vormt een ernstig gevaar voor de veiligheid. 8) De mechanische bouwelementen moeten in overeenstemming zijn met de bepalingen van de normen EN 12604 en EN 12605. Voor niet-EEG landen moeten, om een goed veiligheidsniveau te bereiken, behalve de nationale voorschriften ook de bovenstaande normen in acht worden genomen. 9) GENIUS is niet aansprakelijk als de regels der goede techniek niet in acht genomen zijn bij de bouw van het sluitwerk dat gemotoriseerd moet worden, noch voor vervormingen die zouden kunnen ontstaan bij het gebruik. 10) De installatie dient te geschieden in overeenstemming met de normen EN 12453 en EN 12445. Het veiligheidsniveau van het automatische systeem moet C+D zijn. 11) Alvorens ingrepen te gaan verrichten op de installatie moet de elektrische voeding worden weggenomen en moeten de batterijen worden afgekoppeld. 12) Zorg op het voedingsnet van het automatische systeem voor een meerpolige schakelaar met een opening tussen de contacten van 3 mm of meer. Het wordt geadviseerd een magnetothermische schakelaar van 6A te gebruiken met meerpolige onderbreking. 13) Controleer of er bovenstrooms van de installatie een differentieelschakelaar is geplaatst met een limiet van 0,03 A. 14) Controleer of de aardingsinstallatie vakkundig is aangelegd en sluit er de metalen delen van het sluitsysteem op aan. 15) Het automatische systeem beschikt over een intrinsieke beveiliging tegen inklemming, bestaande uit een controle van het koppel. De inschakellimiet hiervan dient echter te worden gecontroleerd volgens de bepalingen van de normen die worden vermeld onder punt 10. 16) De veiligheidsvoorzieningen (norm EN 12978) maken het mogelijk eventuele gevaarlijke gebieden te beschermen tegen Mechanische gevaren door beweging, zoals bijvoorbeeld inklemming, meesleuren of amputatie. 17) Het wordt voor elke installatie geadviseerd minstens één lichtsignaal te gebruiken alsook een waarschuwingsbord dat goed op de constructie van het hang- en sluitwerk dient te worden bevestigd, afgezien nog van de voorzieningen die genoemd zijn onder punt “16”. 18) GENIUS aanvaardt geen enkele aansprakelijkheid voor wat betreft de veiligheid en de goede werking van het automatische systeem, als er in de installatie gebruik gemaakt wordt van componenten die niet door GENIUS zijn geproduceerd. 19) Gebruik voor het onderhoud uitsluitend originele GENIUS-onderdelen. 20) Verricht geen wijzigingen op componenten die deel uitmaken van het automatische systeem. 21) De installateur dient alle informatie te verstrekken over de handbediening van het systeem in noodgevallen, en moet de gebruiker van de installatie het bij het product geleverde boekje met aanwijzingen overhandigen. 22) Sta het niet toe dat kinderen of volwassenen zich ophouden in de buurt van het product terwijl dit in werking is. 23) Houd radio-afstandsbedieningen of alle andere impulsgevers buiten het bereik van kinderen, om te voorkomen dat het automatische systeem onopzettelijk kan worden aangedreven. 24) Ga alleen tussen de vleugels door als het hek helemaal geopend is. 25) De gebruiker mag geen pogingen tot reparatie doen of directe ingrepen plegen, en dient zich uitsluitend te wenden tot gekwalificeerd personeel. 26) Breng de polen van de batterijen niet in kortsluiting en probeer niet de batterijen op te laden met andere voeders dan de Master- of Slave-kaarten. 27) Gooi lege batterijen niet weg bij het gewone afval, maar maak gebruik van de speciale verzamelbakken om recycling mogelijk te maken. De kosten voor afvalverwerking zijn al betaald door de fabrikant. 28) Alles wat niet uitdrukkelijk in deze instructies wordt aangegeven, is niet toegestaan  DICHIARAZIONE CE DI CONFORMITÁ PER CE DECLARATION OF MACHINE CONFORMITY MACCHINE (DIRECTIVE 89/392/EEC, ANNEX II, PART B) (DIRETTIVA 98/37/CE) DECLARATION CE DE CONFORMITÉ POUR MACHINES (DIRECTIVE 89/392/CEE, ANNEXE II, PARTIE B) Manufacturer : GENIUS S.r.l. Address: Via Padre Elzi, 32 24050 Grassobbio, BG, ITALY Declares that: Operator mod. G60 and G100 Fabricant: GENIUS S.r.l. Adresse: Via Padre Elzi, 32 24050 Grassobbio, BG, ITALIE Déclare que: L’opérateur mod. G60 et G100 •è costruito per essere incorporato in una macchina o per essere assemblato con altri macchinari per CE costituire una macchina ai sensi della Direttiva 98/37/CE; •is manufactured to be incorporated in a machine or for assembly with other machines to constitute a machine under the provisions of Directive 89/392/EEC, and subsequent amendments 91/368/EEC, 93/44/EEC, 93/68/EEC; •est construit pour être incorporé dans une machine et pour être assemblé à d’autres machines en vue de constituer une machine conformément à la Directive 89/392/CEE et modifications 91/368/ CEE, 93/44/CEE 93/68/CEE successives; •è conforme ai requisiti essenziali di sicurezza delle seguenti altre direttive CEE: •conforms to the essential safety requirements of the following further EEC Directives: •est conforme aux exigences essentielles de sécurité des autres directives CEE suivantes: 73/23/EEC and subsequent amendment 93/68/EEC. 89/336/EEC and subsequent amendment 92/31/EEC and 93/68/ EEC 73/23/CEE et modification 93/68/CEE successive, 89/336/CEE et modifications 92/31/CEE et 93/68/CEE successives. and, furthermore, declares that putting the machine into service is forbidden until the machine in which it will be incorporated or of which it will become a part has been identified and it has been declared as conforming to the conditions of Directive 89/392/ EEC and subsequent amendments enacted by the national implementing legislation. Et déclare, en outre, qu’il est interdit de mettre en service l’appareillage jusqu’à ce que la machine dans laquelle il sera incorporé ou dont il deviendra un composant ait été identifiée et jusqu’à ce que la conformité aux conditions de la Directive 89/392/CEE et des décrets de transposition de la directive. Fabbricante: GENIUS S.r.l. Indirizzo: Via Padre Elzi, 32 24050 Grassobbio, BG, ITALIA Dichiara che: L'operatore mod. G60 e G100 73/23/CEE e successiva modifica 93/68/CEE. 89/336/CEE e successiva modifica 92/31/CEE e 93/68/CEE e inoltre dichiara che non è consentito mettere in servizio il macchinario fino a che la macchina in cui sarà incorporato o di cui diverrà componente sia stata identificata e ne sia stata dichiarata la conformità alle condizioni della Direttiva 89/392/CEE e successive modifiche trasposta nella legislazione nazionale dal DPR n° 459 del 24 luglio 1996. Grassobbio, 1 Marzo 2004 Grassobbio, le 1 Mars 2004 Grassobbio, 1 March 2004 L’Administrateur Délégué D. Gianantoni L’Amministratore Delegato D. Gianantoni Managing Director D. Gianantoni DECLARACIÓN CE DE CONFORMIDAD PARA MAQUINAS KONFORMITÄTSERKLÄRUNG CE FÜR MASCHINEN (RICHTLINIE 89/392/EWG, ANLAGE II, TEIL B) (DIRECTIVA 89/392/CEE, ANEXO II, PARTE B) Fabricante: GENIUS S.r.l. Dirección: Via Padre Elzi, 32 24050 Grassobbio, BG, ITALIA Declara que: El operador mod. G60 y G100 •ha sido fabricado para ser incorporado a una máquina o para ser ensamblado con otras maquinarias para constituir una máquina según lo establecido por la Directiva 89/392/CEE y sucesivas modificaciones 91/368/CEE, 93/68/CEE; •cumple con los requisitos esenciales de seguridad de las siguientes directivas CEE: 73/23/CEE y sucesiva modificación 93/68/CEE 89/336/CEE y sucesiva modificación 92/31/CEE y 93/68/CEE así mismo declara que no está permitido poner en funcionamiento la maquinaria hasta que la máquina en la cual será acoplada o de la cual entrará a formar parte haya sido identificada y se haya declarado su conformidad con lo establecido por la Directiva 89/392/CEE y sus sucesivas modificaciones, y a la ley que la incorpora en la legislación nacional. CE VERKLARING VAN OVEREENSTEMMING VOOR MACHINES (RICHTLIJN 89/392/EEG, BIJLAGE II, DEEL B) Der Hersteller: GENIUS S.r.l. Anschrift: Via Padre Elzi, 32 24050 Grassobbio, BG, ITALIEN erklärt, daß: der Getriebemotor Mod. G60 G100, und Fabrikant: GENIUS S.r.l. Adres: Via Padre Elzi, 32 24050 Grassobbio, BG, ITALIE Verklaart dat: de aandrijving mod. G60 en G100 •für den Einbau in eine Maschine oder für den Zusammenbau mit anderen Geräten zu einer vollständigen Maschine gemäß der Richtlinie 89/392/EWG und den nachfolgenden Änderungen 91/368/EWG, 93/44/EWG, 93/68/EWG hergestellt wurde; •gebouwd is voor opname in een machine of voor assemblage met andere machines zodat een machine gevormd wordt in de zin van de Richtlijn 89/392/EEG en latere wijzigingen 91/368/EEG, 93/44/EEG, 93/68/EEG; •den wesentlichen Sicherheitsanforderungen der folgenden EWGRichtlinien entspricht: •in overeenstemming is met de fundamentele veiligheidseisen van de volgende andere EEG-richtlijnen: 73/23/EWG und nachfolgende Änderung 93/68/EWG. 89/336/EWG und nachfolgende Änderungen 92/31/EWG und 93/68/EWG 73/23/EEG en latere wijziging 93/68/EEG. 89/336/EEG en latere wijziging 92/31/EEG en 93/68/EEG und erklärt außerdem, daß die Inbetriebnahme solange untersagt ist, bis die Maschine, in welche diese Maschine eingebaut wird oder von der sie ein Bestandteil ist, den Bestimmungen der Richtlinie 89/392/ EWG sowie deren nachträglichen Änderungen entspricht. en verklaart bovendien dat het niet is toegestaan de machine in bedrijf te stellen voordat de machine waarin zij zal worden ingebouwd of waarvan zij onderdeel zal uitmaken geïdentificeerd is en in overeenstemming is verklaard met de voorwaarden van de Richtlijn 89/392/EEG en latere wijzigingen. Grassobbio, 1 März 2004 Grassobbio, 1 Maart 2004 Der Geschäftsführer D. Gianantoni Grassobbio, 1º de Marzo de 2004 Administrador Delegado D. Gianantoni President - directeur D. Gianantoni Le descrizioni e le illustrazioni del presente manuale non sono impegnative. GENIUS si riserva il diritto, lasciando inalterate le caratteristiche essenziali dell’apparecchiatura, di apportare in qualunque momento e senza impegnarsi ad aggiornare la presente pubblicazione, le modifiche che essa ritiene convenienti per miglioramenti tecnici o per qualsiasi altra esigenza di carattere costruttivo o commerciale. The descriptions and illustrations contained in the present manual are not binding. GENIUS reserves the right, whils leaving the main features of the equipments unaltered, to undertake any modifications to holds necessary for either technical or commercial reasons, at any time and without revising the present publication. Les descriptions et les illustrations du présent manuel sont fournies à titre indicatif. GENIUS se réserve le droit d’apporter à tout moment les modifications qu’elle jugera utiles sur ce produit tout en conservant les caractéristiques essentielles, sans devoir pour autant mettre à jour cette publication . GENIUS S.p.A. Via Padre Elzi, 32 24050 - Grassobbio BERGAMO-ITALY tel. 0039.035.4242511 fax. 0039.035.4242600 [email protected] www.geniusg.com Las descripciones y las ilustraciones de este manual no comportan compromiso alguno. GENIUS se reserva el derecho, dejando inmutadas las características esenciales de los aparatos, de aportar, en cualquier momento y sin comprometerse a poner al día la presente publicación, todas las modificaciones que considere oportunas para el perfeccionamiento técnico o para cualquier otro tipo de exigencia de carácter constructivo o comercial. Die Beschreibungen und Abbildungen in vorliegendem Handbuch sind unverbindlich. GENIUS behält sich das Recht vor, ohne die wesentlichen Eigenschaften dieses Gerätes zu verändern und ohne Verbindlichkeiten in Bezung auf die Neufassung der vorliegenden Anleitungen, technisch bzw, konstruktiv / kommerziell bedingte Verbesserungen vorzunehmen. De beschrijvingen en illustraties in deze handleiding zijn niet bindend. GENIUS behoudt zich het recht voor om op elk willekeurig moment, en zonder verplicht te zijn deze publicatie bij te werken, de wijzigingen aan te brengen die wenselijk geacht worden met het oog op technische verbeteringen of om andere redenen van technische of commerciële aard, waarbij de essentiële eigenschappen van de apparatuur ongewijzigd blijven. Timbro rivenditore / Distributor’s stamp / Timbre de l’agent / Sello del revendedor / Fachhändlerstempel / Stempel van de dealer 732522 REV.2