Emerson EMMC35881 Manual de usuario

Marca: Emerson

Modelo: EMMC35881

Categoría: Reproductores de CD

Tipo: Manual de usuario

La página se está cargando ...



Read this manual thoroughly before using!!!

INTRODUCTION

Thank you for purchasin g our produc t. You now p ossess a quality stereo Radio / Video

Compact Disc Player. Used c arefully and in accordance with th e instructions set out below

your stereo Radio/Video Compact Disc Player should give you many years of trouble free

serv ice. Please read the instructions carefully to obtain the best results from your

purchase.

FEATURES

Ĵ Top load VCD player with analog tu ner micro compo syste m with CFD display

Ĵ AM/FM radio

Ĵ 3 digit LCD display er for CD

Ĵ Programm able memories

Ĵ SVCD function

Ĵ Play –Pause /Stop/Skip-search/Repeat/Program

Ĵ Tape: single tape deck

Ĵ Auto stop cassette mechanism

Ĵ Soft eject cassette doo r

Ĵ Automatic recording level control

Ĵ Tuning control ,volume control

Ĵ Tact switch CD control buttons

Ĵ Telescopic antenna with remote control

Ĵ Wooden speaker

Ĵ With a pair of joy sticker

CONTROL OPERATIONS A ND FUNCTIONS

CONNECTING TO A TV SET AS FOLLOWING:

NOTE: When it can't work normally on first powering of this un it, please power i t off. And

turn on the power again after checking the corresponding connections whether they are

ok.

¡¡Lea este manual detenidamente antes de usar!!

INTRODUCCIÓN

Gracias por haber comprado nuestro producto. Ahora tiene en sus manos una Radio Estéreo

y Reproductor de Video y Discos Compactos CD de calidad. Si se usa cuidadosamente y de

acuerdo a las instrucciones descritas abajo, esta Radio Estéreo y Reproductor de Video y

Discos Compactos le ofrecerá años de buen funcionamiento sin ningún problema. Por favor

lea estas instrucciones cuidadosamente con el n de obtener los mejores resultados de su

compra.

CARACTERÍSTICAS

• Reproductor de VCD superior con sistema ligero componente de sintonizador análogo y

con pantalla CFD

• Radio AM / FM

• Pantalla LCD de tres dígitos para CD

• Memoria programable

• Función SVCD

• Reproducción - Pausa /Detener/Salto - Búsqueda/Repetición/Programa

• Casete: una casetera

• Mecanismo de detención automática del casete

• Eyección suave de la puerta del casete

• Control de nivel automático de grabación

• Control de sintonización, control de volumen

• Botones de control del CD al tacto

• Antena telescópica con control remoto

• Altavoz de madera

• Un par de mandos para juegos

Audio output jack(R)

Audio output jack(L)

Video output jack

Video/Audio Cable

Yellow

Video input jack

Audio input jack(L)

Audio input jack(R)

Red

White



Read this manual thoroughly before using!!!

INTRODUCTION

Thank you for purchasin g our produc t. You now possess a quality stereo Radio / Video

Compact Disc Player. Used c arefully and in accordance with th e instructions set out below

your stereo Radio/Video Compact Disc Player should give you many years of trouble free

serv ice. Please read the instructions carefully to obtain the best results from your

purchase.

FEATURES

Ĵ Top load VCD player with analog tu ner micro compo syste m with CFD display

Ĵ AM/FM radio

Ĵ 3 digit LCD display er for CD

Ĵ Programm able memories

Ĵ SVCD function

Ĵ Play –Pause /Stop/Skip-search/Repeat/Program

Ĵ Tape: single tape deck

Ĵ Auto stop cassette mechanism

Ĵ Soft eject cassette doo r

Ĵ Automatic recording level control

Ĵ Tuning control ,volume control

Ĵ Tact switch CD control buttons

Ĵ Telescopic antenna with remote control

Ĵ Wooden speaker

Ĵ With a pair of joy sticker

CONTROL OPERATIONS A ND FUNCTIONS

CONNECTING TO A TV SET AS FOLLOWING:

NOTE: When it can't work normally on first powering of this un it, please power i t off. And

turn on the power again after checking the corresponding connections whether they are

ok.

Video input jack

CONTROLES Y FUNCIONES

CÓMO CONECTAR A UN TELEVISOR

Entrada de audio (der.)

Entrada de audio (izq.)

Rojo

Amarillo

Blanco

Cable de Video / Audio

Salida de audio (der.)

Salida de audio (izq.)

Salida de video

NOTA: Si el aparato no funciona normalmente al encenderlo por primera vez, apáguelo.

Luego enciéndalo de nuevo después de revisar las conexiones correspondientes y vericar

si se encuentran bien.

NOTE:

1. If you want to conne ct the player at a scart jack to your Video recorder or TV, you have

to use an RCA-To- Scart adaptor. This adaptor is available at every Audio -Video-Retailer.

2. This player mu st be conne cted to a multi-system TV or NTS C TV for supporting NTSC

signal format.

3. En sure that this player and other equipment to b e connected are set to the standby

mode or off and disconnect the AC powe r cords before commencing connection.

4. Do not block ve ntilation holes of any o f the equipm ent a nd arrange them, so that air can

circula te freely.

5. Read th rough the instructions before connecting other equipment.

6. En sure that you observ e the color coding wh en con necting audio and video cables.

7. During PLAY, the TV volume may be at a lower level than during TV broadcasts, etc. If

this is the case, adjust the v olume to the desired level.

IMPORTANT SAFETY INSTRUC TIONS

1. Read these instructions. Keep these instructions.

2. Heed all w arnings.

3. Follow all instructions.

4. Do not use this app aratus near water.

5. Clean only with dry cloth.

6. Do not block any ventilation op enings. Install in accordance with the manufactu rer's

instructions.

7. Do not install near any heat sources such as radiators, heat registers, stoves, or

other apparatus (including amplifiers) that produce heat.

8. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized

plug has two blades. A grounding type plug has two blades and a third grounding

prong. The blades or the third prong is provided for you r safe ty. If the provided plug

does not fit into your outlet, con sult an e lectrician for replacement of the obsolete

outlet.

10ǃ Protect the power cord from being walked on or pinch particularly at plugs,

convenience receptacles, and the point w here they exit from the apparatus.

11ǃOnly use attachments/acc essories specified by the manufacturer.

12ǃUn plug this apparatus during lightening storms or when unused for long periods of

time.

13ǃRe fer all servicing to qualified servicing personnel. Servicing is required when the

apparatus has been damaged in any way, suc h as power supply cord or plug is

damage d, the appliance has been exposed to rain or moisture, does not operate

normally, or has been dropped.

14ǃThis appliance sh all not be exposed to dripping or splashing water, and that no object

filled with liquid such as vases shall be placed on the ap paratus

PRECAUTIONS

● When the set is not going to be used for a long time, plu g the AC lead

● Never open the covers or touch the inside or insert a metal object. Any of these

operations could cause a n electric shock or a fault.

● When thunder starts, u nplug the power cord from the AC outlet.

● Do not expose the unit to direct sunlight, extreme heat, and high humidity, or place it

near heat sources, the sea, or in a sandy or dusty place.

● Do not clean the cabinet of the set with strong detergents or solvents as these could

damage the surface finish.

● The apparatus should not be expose d to dripping or splashing.

● Discs which can be played on this player have the following mark on them:

● Do not move the set suddenly from a very cold room into a warm room. When a

chilled CD / MP3 player is moved suddenly to a warm location, moisture conde nsation

may form on the pick-up lens, prev enting proper o peration. In this case, wait 1 to 2

hours before resuming play.

● During playback, if the CD / MP3 player is subjected to a sudden shock or jo lt, some

noise may be produced, this is not a malfunction.

● Do not place any objects in the disc compartment, it may cause d amage to the

mec hanism.

● Remove the disc before moving the set. If the p layer is moved w ith the disc loade d,

the disc may be damaged.

● Do not store discs in high temperature, high-humidity locations. The discs may

develop warps and bec ome unable to play. Also, discs with moisture on them may be

unplayable.

● Wipe any moisture off with a soft, dry clothe, and be sure discs are fully dry before

using.

● Handle the discs carefully so that fingerprints and dust do not adhe re to the surfaces

of the discs. To clean off, use a soft cloth. Do not use a hard cloth since these will mark

the disc.

● If you switch a fluorescent lamp on or off near the se t, you may hear some

interference noise; this is no t a malfunction.

● Safety Check - Upon any completion of service or repairs to this product, ask service

technician to perform safety check to determine that the product is in proper operating

condition.

● Servicing - Do not attempt to service this product yourself as openings or removing

covers may expose you to dangerous voltage or othe r hazards. Refer all service to

qualified servicing personnel.

● serv ice to qualified servicing personnel.

LOCATION OF CONTROLS

1. CD DOOR

2. FUNCTION

SWITCH

3. POWER SWITCH

4. PHONE JACK

5. REPEAT

NOTA:

1.Si se desea conectar el reproductor a un grabador de video o televisor, se tiene que utilizar un

adaptador RCA. Este adaptador se encuentra disponible en cualquier tienda de audio y video.

2.Este reproductor debe conectarse a un sistema múltiple de TV o a un televisor NTSC con

formato de señal NTSC.

3.Asegúrese de que este reproductor y cualquier otro equipo que se conecte se encuentren

apagados o desconectados de la electricidad antes de efectuar las conexiones.

4.No obstruya los agujeros de ventilación de cualquier equipo y colóquelos de tal manera que el

aire pueda circular libremente.

5.Lea todas las instrucciones antes de efectuar las conexiones del equipo.

6.Asegúrese de prestar atención a los códigos de colores a la hora de conectar los cables de

audio y video.

7.Durante la reproducción, el volumen del televisor puede estar a un nivel más bajo que durante

los programas de televisión normales. Si este fuera el caso, regule el volumen a nivel deseado.

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

1.Lea estas instrucciones. Guarde estas instrucciones.

2.Obedezca todas las advertencias.

3.Siga todas las instrucciones.

4.No utilice este aparato cerca al agua.

5.Limpie solo con un paño seco.

6.No obstruya las aberturas de ventilación. Instale de acuerdo a las instrucciones del fabricante.

7.No lo instale cerca de fuentes de calor tales como estufas, termostatos, cocinas o cualquier

otro aparato (incluyendo amplicadores) que produzca calor.

8.No elimine el sistema de seguridad del enchufe polarizado o de tierra. El enchufe polarizado

tiene dos extremidades. El de tierra tiene, además de las dos extremidades, una pata o ex-

tremidad adicional a tierra. Estas extremidades especiales están diseñadas para su seguridad.

Si el enchufe no encaja en su tomacorriente, consulte a un electricista para que reemplace su

tomacorriente obsoleto.

9.Evite que se pise o se apriete el cordón, especialmente en la parte del enchufe y en la parte de

donde éste sale del aparato.

10.Utilice solamente los aditamentos o accesorios especicados por el fabricante.

11.Desenchufe este aparato durante las tormentas eléctricas o cuando no lo utilice por periodos

largos.

12.Todo servicio de mantenimiento debe de ser llevado a cabo por el personal calicado. Este

servicio es necesario cuando se ha dañado el aparato de cualquier forma, incluyendo el cordón o

enchufe, cuando se le ha expuesto a la lluvia o humedad, cuando no funcione de manera normal

o cuando haya sufrido una caída.

13.No debe de exponerse este aparato a goteras o salpicaduras de agua; no coloque objetos con

agua, tales como un orero, encima del aparato.

PRECAUCIONES

•Cuando no se vaya a usar el aparato por un periodo largo, desenchufe el cable AC.

•Nunca abra las tapas del aparato o toque el interior ni inserte un objeto de metal. Cualquiera de

estas cosas puede ocasionar una descarga eléctrica o desperfecto.

•Si hubiera una tormenta eléctrica, desenchufe del tomacorriente AC.

•No exponga el aparato a la luz solar directa, al calor extremo y a mucha humedad ni lo coloque

cerca de fuentes de calor, el mar o en lugares con arena o polvo.

NOTE:

1. If you want to conne ct the player at a scart jack to your Video recorder or TV, you have

to use an RCA-To- Scart adaptor. This adaptor is available at every Audio -Video-Retailer.

2. This player mu st be conne cted to a multi-system TV or NTS C TV for supporting NTSC

signal format.

3. En sure that this player and other equipment to b e connected are set to the standby

mode or off and disconnect the AC powe r cords before commencing connection.

4. Do not block ve ntilation holes of any o f the equipm ent a nd arrange them, so that air can

circula te freely.

5. Read th rough the instructions before connecting other equipment.

6. En sure that you observ e the color coding wh en con necting audio and video cables.

7. During PLAY, the TV volume may be at a lower level than during TV broadcasts, etc. If

this is the case, adjust the v olume to the desired level.

IMPORTANT SAFETY INSTRUC TIONS

1. Read these instructions. Keep these instructions.

2. Heed all w arnings.

3. Follow all instructions.

4. Do not use this app aratus near water.

5. Clean only with dry cloth.

6. Do not block any ventilation op enings. Install in accordance with the manufactu rer's

instructions.

7. Do not install near any heat sources such as radiators, heat registers, stoves, or

other apparatus (including amplifiers) that produce heat.

8. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized

plug has two blades. A grounding type plug has two blades and a third grounding

prong. The blades or the third prong is provided for you r safe ty. If the provided plug

does not fit into your outlet, con sult an e lectrician for replacement of the obsolete

outlet.

10ǃ Protect the power cord from being walked on or pinch particularly at plugs,

convenience receptacles, and the point w here they exit from the apparatus.

11ǃOnly use attachments/acc essories specified by the manufacturer.

12ǃUn plug this apparatus during lightening storms or when unused for long periods of

time.

13ǃRe fer all servicing to qualified servicing personnel. Servicing is required when the

apparatus has been damaged in any way, suc h as power supply cord or plug is

damage d, the appliance has been exposed to rain or moisture, does not operate

normally, or has been dropped.

14ǃThis appliance sh all not be exposed to dripping or splashing water, and that no object

filled with liquid such as vases shall be placed on the ap paratus

PRECAUTIONS

● When the set is not going to be used for a long time, plu g the AC lead

● Never open the covers or touch the inside or insert a metal object. Any of these

operations could cause a n electric shock or a fault.

● When thunder starts, u nplug the power cord from the AC outlet.

● Do not expose the unit to direct sunlight, extreme heat, and high humidity, or place it

near heat sources, the sea, or in a sandy or dusty place.

● Do not clean the cabinet of the set with strong detergents or solvents as these could

damage the surface finish.

● The apparatus should not be expose d to dripping or splashing.

● Discs which can be played on this player have the following mark on them:

● Do not move the set suddenly from a very cold room into a warm room. When a

chilled CD / MP3 player is moved suddenly to a warm location, moisture conde nsation

may form on the pick-up lens, prev enting proper o peration. In this case, wait 1 to 2

hours before resuming play.

● During playback, if the CD / MP3 player is subjected to a sudden shock or jo lt, some

noise may be produced, this is not a malfunction.

● Do not place any objects in the disc compartment, it may cause d amage to the

mec hanism.

● Remove the disc before moving the set. If the p layer is moved w ith the disc loade d,

the disc may be damaged.

● Do not store discs in high temperature, high-humidity locations. The discs may

develop warps and bec ome unable to play. Also, discs with moisture on them may be

unplayable.

● Wipe any moisture off with a soft, dry clothe, and be sure discs are fully dry before

using.

● Handle the discs carefully so that fingerprints and dust do not adhe re to the surfaces

of the discs. To clean off, use a soft cloth. Do not use a hard cloth since these will mark

the disc.

● If you switch a fluorescent lamp on or off near the se t, you may hear some

interference noise; this is no t a malfunction.

● Safety Check - Upon any completion of service or repairs to this product, ask service

technician to perform safety check to determine that the product is in proper operating

condition.

● Servicing - Do not attempt to service this product yourself as openings or removing

covers may expose you to dangerous voltage or othe r hazards. Refer all service to

qualified servicing personnel.

● serv ice to qualified servicing personnel.

LOCATION OF CONTROLS

1. CD DOOR

2. FUNCTION

SWITCH

3. POWER SWITCH

4. PHONE JACK

5. REPEAT

•No limpie el exterior con detergentes fuertes o solventes ya que estos pueden dañar el acabado

de la supercie.

•No debe exponerse el aparato a goteras o salpicaduras.

•Los discos que puedan reproducirse en este aparato deberán de portar la siguiente marca:

•No traslade el aparato repentinamente de un ambiente frío a uno caliente. Cuando un repro-

ductor de CD / MP3 que se encuentra frío es trasladado repentinamente a un lugar caliente, se

puede formar condensación de humedad en el lente de lectura, lo que puede interferir con su

normal funcionamiento. En este caso, espere de 1 a 2 horas antes de reanudar su uso.

•Durante la reproducción, si el reproductor de CD / MP3 es sometido a un golpe o sacudón

fuerte, se puede producir algo de ruido. Esto no indica que haya un desperfecto.

•No coloque ningún objeto dentro del compartimiento del disco ya que puede causar daños al

mecanismo.

•Retire el disco antes de trasladar el aparato. Si se traslada el aparato con el disco puesto, el

disco puede dañarse.

•No guarde o almacene los discos en lugares de alta temperatura o de gran humedad. Los

discos pueden desnivelarse o torcerse y volverse inservibles. Además, los discos con humedad

sobre la supercie quizá no puedan reproducirse.

•Limpie la humedad con un paño suave y seco y asegúrese de que los discos estén totalmente

secos antes de usarlos.

•Manipule los discos con cuidado para evitar que no se adhieran huellas digitales o polvo sobre

la supercie. Para limpiar use un paño suave. No utilice un paño áspero ya que puede arañar el

disco.

•Si se enciende o se apaga una lámpara uorescente cerca del aparato, se puede producir algo

de interferencia, lo cual no indica un desperfecto.

•Revisión de Seguridad – Al nal de una reparación o mantenimiento del aparato, solicite al

técnico que haga una prueba de seguridad para determinar que el producto esté en condiciones

óptimas de funcionamiento.

•Mantenimiento o Reparaciones – No intente reparar el aparato Ud. mismo ya que las aberturas

o el retiro de las tapas pueden exponerlo a voltajes peligrosos u otros riesgos. Todo manten-

imiento debe de ser llevado a cabo por el personal de servicio técnico calicado.

UBICACIÓN DE LOS CONTROLES

1. CD DOOR

2. FUNCTION SWITCH

3. POWER SWITCH

4. PHONE JACK

5. REPEAT

1. PUERTA DEL CD

2. BOTÓN DE FUNCIONES

3. BOTÓN DE ENCENDIDO

4. ENTRADA PARA EL MICRÓFONO

5. REPETIR

La página se está cargando ...

6. PROGRAM

7.CD PLAY/PAUSE

8.LCD DISPLAY

9.CFD

10. V OLUME CONTROL

11.CD STOP SWITCH

12.CD SKIP-

13. TUNING

14. CD SKIP+

15. B AND SWITCH

16 SPEAKER

17. CASSETTE RECO RD SWITCH

18. CASSETTE PLAY SWITCH

19. CASSETTE REW SWITCH

20. CASSETTE FWD SWITCH

21 CASSETTE STOP/EJECT SW ITCH

22. CASSETTE PAUSE SWITCH

23. CASSETTE HOLDER

24 .A NTENNA

25. B ACK COVER

26. S PEAKER OUTPU T

TERMINAL(RIGHT ).

27 SPEAKER OUTPUT

TERMINAL(LEFT)

28. A C SOC KET

29. A UDIO OUT

30. V IDEO OUT

31. JOYSTICK T ERMINAL

specifications

Frequency Range FM:88-108MHz,AM:530-1700KHz

Power Requirements 120V,60Hz

Specifications are subject to change for performance improvement without notice.

POWER SUPPLY

AC OPERATION

- THE AC POWER COR D IS LOCATED

- PLUG THE AC LINE CORD INTO ANY NORMAL HOUSEHOLD AC MAINS

OUTLET IN CORRECT VOLTAGE AND THE MAINS SOCKE T.

STANDBY INDICATOR

When the power is connected to AC outlet, the ST ANDBY LED indicator will ligh t up. You

have to press the POWER button on the unit or POWER button on the remote to turn on

the unit.

RADIO OPERATION

1. Connect the unit to the power source.

2. Slide the FUNCT ION SWITCH to "RADIO" position.

3. Se lect desired wave band with the BAND SWITCH.

4. Tune to desi red station by rotating the TUNING KNOB.

5. Gently rotate this con trol back & forth until you get the strongest, clearest sound.

6. The built-in MW(AM) or LW antenna and the SW antenna rod are directional. When

receiving SW broadcast, extend the SW ELESCOPIC ANTENNA in full length.

The strongest reception can be ach ieved by rotating the set for MW(AM) or LW or

Telescopic Antenna for FM or SW.

7. Ad just the VOLU ME KNO B to your listening preference.

8. To turn off the radio, slide the FUNCTION SW ITCH to "TAPE" position .

CASSETT E OPERATION

PLAYBAC K OF CASS ETTE

Be sure to tighten any slac k tape in the cassette before use, using either a pencil or a

ball-point pen, simply insert the pen or pencil into the centre of spool and rotate to remove

slackess.

Depress the S TOP/EJECT button to open the cassette door.

Insert the cassette into the compartment with the open end facing upward and the full reel

on the le ft hand side, push the cassette well down and close the door, be sure not to touc h

the tape surface. Set the Fun ction switch to "TAPE " position and press the cassette play

button. To stop playb ack, press the STOP/E JECT button again.

AUTO STOP

When the tape reaches the end during play back or recording, the built-in auto stop system

will release the depressed play, record keys. The auto stop system operate s while

recording from the built-in radio or CD player, only the cassette function is brought

automatically to stop mode and the radio or CD Player will continue to play.

TAPE RECORDING

A. Install a cassette tape.

B. Set FUNCT ION SWITCH to "RADIO" position. After selecting the desired band and

tune the T UNING KNOB to des ired broadcast station. Then push down RECORD

BUTTON and PLAY BUTTON simultaneously.

C. After recording the desired broadcast, depres s the STOP/EJECT BUT TON lightly, and

then set FUNCTION SWITCH to "TAPE" position in order to lis ten to the recorded

broadca st.

D. If you desire to play recorded broadcast, please follow the instructions explained in

playback section.

Note: Tape recording is also available for VCD/CD/MP3 playback (set FUNCTION

SWITCH to "VCD/CD/MP3" po sition). Similar as radio recording.

External MIC recording: Set FUNCTION SWITCH to "TAPE" position, press the RECORD

BUTTON and PLAY BUTTON simultaneously and speak thro ugh external MIC.

TYPES OF CASSETTE

Use only good quality cassettes (IEC TYPE 1) for making recordings. May be used to

replay other ty pes of cassette but is unable to make p roper recordings on thes e more

specialized tapes.

The us e of C120 cassettes is NOT recommended in this machine.

PROTECTING RECORDING

25 28

22 23

16 16

5.Suavemente gire el control de sintonización hacia adelante y hacia atrás hasta obtener un

sonido bueno y claro.

6.El cable incorporado de la antena MW (AM) o LW y la antena SW son direccionales. Si se

recibe señal SW, extienda la antena telescópica SW totalmente. La mejor recepción se puede

lograr agotando el aparato en el caso de MW (AM) o la antena telescópica en el caso de FM o

SW.

7.Regule el control de VOLUMEN al nivel deseado.

8.Para apagar la radio, deslice el selector de FUNCIONES a la posición de TAPE (casete).

FUNCIONAMIENTO DE LA CASETERA

REPRODUCCIÓN DE UN CASETE

Asegúrese de ajustar la cinta que se encuentre suelta dentro del casete antes de usarlo utili-

zando ya sea un lápiz o lapicero simplemente insertando el lápiz o lapicero dentro del centro

de carrete y girando para ajustar la cinta.

Presione el botón STOP / EJECT para abrir la puerta del casete.

Inserte el casete dentro del compartimiento con la parte que se encuentra abierta hacia arriba

y con el carrete lleno en el lado izquierdo. Empuje del casete hacia abajo y cierre la puerta.

Asegúrese de no tocar la supercie de la cinta. Coloque el selector de funciones en la posición

“TAPE” y presione el botón reproducir del casete. Para detener la reproducción, presione el

botón STOP / EJECT de nuevo.

DETENCIÓN AUTOMÁTICA

Cuando la cinta alcance el nal durante la reproducción o grabación, el sistema incorporado de

extensión automática hará que los botones de reproducción y de grabación salten. El sistema

de detención automática funciona mientras se esté grabando de la radio incorporada o del

reproductor de discos. Sólo la función de casete se detiene automáticamente ya que la radio o

el reproductor de discos continuarán funcionando.

GRABACIÓN DE CINTAS

A.Instale una cinta de casete

B.Coloque el selector de funciones en la posición “RADIO”. Después de seleccionar la banda

deseada sintonizara con el botón de sintonización la emisora deseada, presione el botón de

grabación (RECORD) y el botón de reproducción (PLAY) simultáneamente.

C.Después de grabar el programa deseado, presione el botón STOP / EJECT y coloque el

selector de funciones en la posición “TAPE” para escuchar lo que se ha grabado.

D.Si se desea reproducir un programa grabado, siguen las instrucciones que se explican en la

sección de reproducción.

Nota: También se puede grabar cintas de la reproducción de CVD/CD/MP3 (coloque el selector

de funciones en la posición “CVD/CD/MP3”. El procedimiento es similar a la grabación de la

radio.

Grabación de un micrófono externo: Coloque el botón de funciones en la posición “TAPE” y

luego presione los botones de reproducción y grabación simultáneamente y proceda a hablar a

través de micrófono externo.

TIPOS DE CASETE

Utilice solamente casetes de buena calidad (IEC TIPO 1) para efectuar grabaciones. Se puede

reproducir otros tipos de casetes pero las grabaciones no pueden ser las más apropiadas con

este tipo de casetes especializados.

NO se recomienda el uso de casetes C120 con este equipo.

CÓMO PROTEGER LA GRABACIÓN

Normally, anything recorded on the tap e is automatically erased when ne w recording is

made. It is possible to protect your record ing from accidental erasure b y removing the tabs

found on the rear of the cassette.

When the cassette is held with the recorded side upper-most and exposed tape facing the

front, the protective tab wi ll be found on the left rear of the cassette.

All pre-recorded cassette are protected in this way to prevent accidental erasure of th e

com mercial recording. "P rotected" cassette will prevent the record button from being

operated. If at an y time you atte mpt to rec ord and find that this button will not d epress,

never force the mechanism or it may b e damaged. Check that a cassette has been loaded

and that tab has not bee n remo ved.

Recording on a ca ssette from which the tabs h ave been removed can be done by covering

the tab openings with a piece of adhesive tape.

CARE OF CASSETTE MECHANISM

Gently clean the tape head and pinch wheel/capstan assemblies after every 10 hours of

using the unit. A range of casse tte care products are available.

PLAYING VCD/CD

Set FUNCTION SWITCH to "CD/VCD" position. Open the CD door to put in a compact

disc. Close i t and start reading. The LED display always shows the tracks of a disc which

are still to be played. Then it start p layback at first trac k. Total number of tracks of the

disc are shown in stop mode.

When playing, press REPEAT button onc e. REPEAT INDICATOR will light up and flash

for playing the same track only. If repeat all tracks, press the REPEAT button again,

REPEAT INDICATOR wi ll light up. To cancel repeat play, press the REPEAT button until

the repeat indicator disappea rs.

Playing Th e Entire Disc

1. Playback will start by pressing CD PLAY/PAUSE button, playback starts with the first

track.

The display will show the current track num ber.

2. To interrupt playback, p ress CD PLAY/PAUSE button. T he indicator "PAUSE" will light

up.

3. To resume playback, press CD PLAY/PAUSE button once again.

4. To stop playback, p ress CD ST OP button.

Selecting A Different Track During Play

1. Press C D SKIP FORWARD/BACKWARD button on the unit continuously until the

desired track number appears in the display.

2. Playback starts from the desired track.

Stopping p lay

1. Press C D STOP button if y ou wish to stop play. The to tal track number which can be

played will now appear in the display.

2. Open the CD doo r on the unit to remove the CD.

REPEAT PLAY

When playing, press REPEAT button onc e. REPEAT INDICATOR will light up and flash

for playing the same track only. If repeat all tracks, press the REPEAT button again,

REPEAT INDICATOR wi ll light up. To cancel repeat play, press the REPEAT button until

the repeat indicator disappea rs.

PROGRAM PLAY (APPLICABL E DURING REMOTE CONTROL OPERATION)

1. Press "PROG" button to make program memory in stop mode.

2. "PROG" and track pos itions will be shown on the TV screen.

3. Press nume ric button on remote to selec t a track number. The track number will show

on display.

4. Repeat step (3) to program other tracks. During programming, you can press "PROG"

button to canc el the entering proce dure.

5. Total programs available are 20.

6. After finishing programming, press CD PLAY/PAUSE button, playbac k will sta rt from the

first programmed track (Program indicator lights up).

7. Yo u can press CD SKIP FORWARD/BACKWARD button to select the track number in

memory.

8. In stop mode, press STOP button to cance l the program play and the program indicator

will disappear.

Note: For details of VCD/CD/MP 3 operation, please see the remote handset section.

HEA DPHONE JACK

For private listening, insert a 3.5mm hea dphone into the HEADPHONE JACK. The

SPEAKER output is automatically cut off.

CAUTION: LISTE NING AT HIGH POWER FOR A LONG MOMENT COULD DAMAGE

USERS' EARS.

COMPACT DISC MAINTENANCE

1. Always use a compact disc bea ring the mark as shown.

2. Notes on handling discs

* Removing the d isc from its storage case and loading it.

* Do not touch the reflective recorded surface.

* Do not stick paper or write anything on the surface.

* Do not bend the disc.

3. Storage

* Store the disc in its case.

* Do not expose d iscs to direct sunlight or high tempe ratu res, high humidity or dusty

places.

4. Cleaning a disc

* Should the disc become so iled, wipe off dust, dirt and fingerprints with a soft cloth.

* The disc sh ould be cleaned from the centre to the edg e.

* Never use benzene, thinners, record cleaner fluid or a nti-static spray.

CORRECT INCORRECT

Normalmente cualquier cosa que se grabe en una cinta se borra automáticamente cuando se

efectúa una nueva grabación. Es posible proteger una grabación de que será borrada acciden-

talmente retirando las lenguetas en la parte inferior del casete.

Si se sostiene el casete con el lado grabado hacia arriba y con la cinta expuesta hacia el

frente, la lengüeta protectora se encuentra en la parte trasera izquierda del casete.

Todos los casetes que ya vienen pregrabados bien protegidos de esta manera para evitar el

borrado accidental con una grabación comercial. Un casete “protegido” evitará que se pueda

presionar el botón de grabación. Si en cualquier momento que Ud. desee grabar no se puede

presionar este botón, no fuerce el mecanismo ya que puede dañarse. Verique que se haya

colocado un casete y que la lengüeta se haya retirado.

Se puede grabar en un casete cuyas lengüetas han sido retiradas cubriéndolas con un ped-

azo de cinta adhesiva.

CUIDADO DEL MECANISMO DEL CASETE

Suavemente limpie el cabezal y la rueda giratoria cada 10 horas de uso del equipo. Existe una

variedad de productos de limpieza disponibles.

CAPSTAIN

ERASE HEAD

PINCH ROLLER

RECORD/PLAY HEAD

LINGUETE

CABEZAL DE BORRADO

RUEDA GIRATORIA

CABEZAL

REPRODUCCIÓN DE VCD / CD

Coloque el botón de funciones en la posición “CD/VCD”. Abra la tapa del CD para colocar un

disco compacto. Ciérrela y el equipo empezará a leerlo. La pantalla mostrará el número de

pistas del disco por reproducirse. Empezará a reproducirse la primera pista. El número total de

pistas del disco se podrán ver cuando el disco se encuentre detenido.

Durante la reproducción, presione el botón REPEAT una vez. La luz indicadora de repetición

se iluminará de manera intermitente para repetir ésa misma pistas solamente. Si se desea

repetir todas las pistas, presione el botón REPEAT de nuevo. La luz indicadora de repetición se

iluminará. Para cancelar la función de repetición, presione el botón REPEAT hasta que la luz

indicadora desaparezca.

Cómo reproducir el disco completo

1.La reproducción comenzará presionando el botón CD PLAY / PAUSE. La reproducción co-

menzará con la primera pista.

La pantalla mostrará el número de la pista actual.

2.Para interrumpir la reproducción, presione el botón CD PLAY / PAUSE. La luz indicadora

“PAUSE” se iluminará.

3.Para reanudar la reproducción, presione el botón CD PLAY / PAUSE de nuevo.

4.Para detener la reproducción, presione el botón CD STOP.

Cómo seleccionar una pista diferente durante la reproducción

1.Presione el botón CD SKIP FORWARD/BACKWARD en el aparato de manera consecutiva

hasta que la pista deseada aparezca en la pantalla.

2.La reproducción comenzará desde la pista deseada.

Cómo detener la reproducción

1.Presione el botón CD STOP si se desea detener la reproducción. El número total de pistas

que pueden reproducirse aparecerá en la pantalla.

2.Abra la puerta del CD para retirar el disco.

Normally, anything recorded on the tap e is automatically erased when ne w recording is

made. It is possible to protect your record ing from accidental erasure b y removing the tabs

found on the rear of the cassette.

When the cassette is held with the recorded side upper-most and exposed tape facing the

front, the protective tab wi ll be found on the left rear of the cassette.

All pre-recorded cassette are protected in this way to prevent accidental erasure of th e

com mercial recording. "P rotected" cassette will prevent the record button from being

operated. If at an y time you atte mpt to rec ord and find that this button will not d epress,

never force the mechanism or it may b e damaged. Check that a cassette has been loaded

and that tab has not bee n remo ved.

Recording on a ca ssette from which the tabs h ave been removed can be done by covering

the tab openings with a piece of adhesive tape.

CARE OF CASSETTE MECHANISM

Gently clean the tape head and pinch wheel/capstan assemblies after every 10 hours of

using the unit. A range of casse tte care products are available.

PLAYING VCD/CD

Set FUNCTION SWITCH to "CD/VCD" position. Open the CD door to put in a compact

disc. Close i t and start reading. The LED display always shows the tracks of a disc which

are still to be played. Then it start p layback at first trac k. Total number of tracks of the

disc are shown in stop mode.

When playing, press REPEAT button onc e. REPEAT INDICATOR will light up and flash

for playing the same track only. If repeat all tracks, press the REPEAT button again,

REPEAT INDICATOR wi ll light up. To cancel repeat play, press the REPEAT button until

the repeat indicator disappea rs.

Playing Th e Entire Disc

1. Playback will start by pressing CD PLAY/PAUSE button, playback starts with the first

track.

The display will show the current track num ber.

2. To interrupt playback, p ress CD PLAY/PAUSE button. T he indicator "PAUSE" will light

up.

3. To resume playback, press CD PLAY/PAUSE button once again.

4. To stop playback, p ress CD ST OP button.

Selecting A Different Track During Play

1. Press C D SKIP FORWARD/BACKWARD button on the unit continuously until the

desired track number appears in the display.

2. Playback starts from the desired track.

Stopping p lay

1. Press C D STOP button if y ou wish to stop play. The to tal track number which can be

played will now appear in the display.

2. Open the CD doo r on the unit to remove the CD.

REPEAT PLAY

When playing, press REPEAT button onc e. REPEAT INDICATOR will light up and flash

for playing the same track only. If repeat all tracks, press the REPEAT button again,

REPEAT INDICATOR wi ll light up. To cancel repeat play, press the REPEAT button until

the repeat indicator disappea rs.

PROGRAM PLAY (APPLICABL E DURING REMOTE CONTROL OPERATION)

1. Press "PROG" button to make program memory in stop mode.

2. "PROG" and track pos itions will be shown on the TV screen.

3. Press nume ric button on remote to selec t a track number. The track number will show

on display.

4. Repeat step (3) to program other tracks. During programming, you can press "PROG"

button to canc el the entering proce dure.

5. Total programs available are 20.

6. After finishing programming, press CD PLAY/PAUSE button, playbac k will sta rt from the

first programmed track (Program indicator lights up).

7. Yo u can press CD SKIP FORWARD/BACKWARD button to select the track number in

memory.

8. In stop mode, press STOP button to cance l the program play and the program indicator

will disappear.

Note: For details of VCD/CD/MP 3 operation, please see the remote handset section.

HEA DPHONE JACK

For private listening, insert a 3.5mm hea dphone into the HEADPHONE JACK. The

SPEAKER output is automatically cut off.

CAUTION: LISTE NING AT HIGH POWER FOR A LONG MOMENT COULD DAMAGE

USERS' EARS.

COMPACT DISC MAINTENANCE

1. Always use a compact disc bea ring the mark as shown.

2. Notes on handling discs

* Removing the d isc from its storage case and loading it.

* Do not touch the reflective recorded surface.

* Do not stick paper or write anything on the surface.

* Do not bend the disc.

3. Storage

* Store the disc in its case.

* Do not expose d iscs to direct sunlight or high tempe ratu res, high humidity or dusty

places.

4. Cleaning a disc

* Should the disc become so iled, wipe off dust, dirt and fingerprints with a soft cloth.

* The disc sh ould be cleaned from the centre to the edg e.

* Never use benzene, thinners, record cleaner fluid or a nti-static spray.

CORRECT INCORRECT

REPETICIÓN DE LA REPRODUCCIÓN

Durante la reproducción, presione el botón REPEAT una vez. La luz indicadora de repetición

se iluminará de manera intermitente para repetir esa misma pista solamente. Si se desea

repetir todas las pistas, presione el botón REPEAT de nuevo. La luz indicadora de repetición se

iluminará. Para cancelar la función de repetición, presione el botón REPEAT hasta que la luz

indicadora desaparezca.

REPRODUCCIÓN DE PROGRAMA (SOLAMENTE UTILIZANDO EL

CONTROL REMOTO)

1.Presione el botón “PROG” para efectuar la memoria del programa mientras el equipo se

encuentre detenido.

2.Se mostrará en la pantalla la frase “PROG” y las posiciones de las pistas.

3.Presione los botones numéricos en el control remoto para seleccionar los números de las

pistas. El número de la pista se mostrará en la pantalla.

4.Repita el paso (3) para programar otras pistas. Durante la programación, se puede presionar

el botón “PROG” para cancelar lo que se ha ingresado.

5.El número total de programas disponibles es 20.

6.Después de terminar con la programación, presione el botón CD PLAY / PAUSE. La re-

producción comenzará con la primera pista programada (la luz indicadora de programa se

iluminará).

7.Se puede presionar el botón CD SKIP FORWARD/BACKWARD para seleccionar el número

la pista de la memoria.

8.Mientras el aparato se encuentre detenido, presione el botón STOP y el programa y la luz

indicadora desaparecerán.

Nota: Para más detalles sobre el funcionamiento de VCD/CD/MP3, véase la sección del control

remoto.

ENTRADA PARA AUDÍFONOS

Para escuchar el equipo en privado, inserte audífonos de 3.5mm en la entrada para audífonos.

La salida de audio de los altavoces quedará suprimirá automáticamente.

PRECAUCIÓN: EL USO PROLONGADO DE LOS AUDÍFONOS A NIVELES ALTOS DE VOLU-

MEN PUEDE DAÑAR LOS OÍDOS.

MANTENIMIENTO DE LOS DISCOS COMPACTOS

1.Siempre utilice un disco compacto que porten la marca:

2.Notas sobre cómo manipular los discos:

Al retirar el disco de su estuche y ponerlo en el equipo

•No toque la supercie reectora con la grabación

•No adhiera papel ni escriba sobre la supercie.

•No doble del disco.

3.Almacenamiento

•Guarde los discos en sus estuches

•No exponga los discos a la luz solar directa, altas temperaturas, humedad o lugares con polvo.

4.Limpieza del disco

•Si el disco se ensuciara, limpie el polvo, suciedad y huellas digitales con un paño suave.

•Debe limpiarse el disco desde el centro hacia afuera.

FRO M TH E CE NTR E TO TH E ED GE

C O R R E C T INCO R R E CT

CORRECT INCORRECT

FROM CENTRE TO THE EDGE

FRO M TH E CE NTR E TO TH E ED GE

C O R R E C T INCO R R E CT

CORRECTO INCORRECTO

DEL CENTRO HACIA AFUERA

•Nunca utilice bencina, diluentes, limpiadores de discos o aerosoles anti estática.

* Be sure to close the CD door, so the lens is not contamina ted by dust.

* Do not touch the lens.

HANDLING A DISC

LOA DING A DISC

1.Set the FUNC TION Switch to the CD position.

2.Press OPEN Button to open the CD Cover.

3.Insert a disc with the label side toward you if the disc is upside down, the Display will

show 3 dashes

4. Close the CD Door by hand.The Display wi ll show 3 dashes and then the total number

of tracks on the disc.

NOTE: Never touch the laser le ns inside the CD compartment. If it eve r gets dirty,

clean it with a CD cleaner disc.

Althou gh built to withstand a certain amount of the effe cts

from dust , soil an d scratches, discs should be treate d with

the care normally accorded to conventional analog discs

(records). Always protect a disc against scratches, soil and

dust etc. We recommend that during non-use periods the

discs should be store d in the original case.

Bear in mind the following points , since any dirt, scratches or

warping of the disc can cause broken or intermittent sound

and also noise.

● When holding the discs, take care not to touch the

playing surface.

● Store the discs in their cases. Return them to their

cases with the label surface facing up and push down

lightly on the label surface.

Do not place discs in the following locations:

Ĵ Near a heating device or a place where the temperature

is high or in dusty areas.

● Do not write on the label surface using a ballpoint pen

and do not stick labels on the MP3 / CD.

● Wipe away any fingerprints or dust on the p laying

surface of a disc using a soft cloth.

● Bear in mind the following points:

Ĵ Alway s wipe from the inside toward the outside of th e

disc.

Ĵ Never in a circular motion.

Ĵ Do not use conventional record clea ners, anti-static

agents, b enzene, thinner or othe r solvents.

REMOV I NG A DISC

1. Make sure the CD is not playing. If it is, press the CD STOP ( ) Button.

2. Press OPEN button to open the CD Do or.

3. Gently remove the disc .

4. Close the CD Door by hand.

5. Replace the disc in its protective storage box.

DISC PLAYING

NORMAL PLAYBACK

1.Set the FUNCTION Switch to CD position and wait about 5 seconds for CD disc will

need longer time (depended on the size & number of tracks of the disc). After the disc

read completely, the Display will then show the total number of tracks on your compact

disc.

2. Press the CD PLAY /PAUSE ( ) Button to start play, The first track number "001" will

appear in the Display an d the disc will start playing ( please wait for about 5 seconds for

mus ic to sta rt ).

3. Ad just the VOLU ME control to the desired volume level.

4.To stop the d isc temporarily, press the CD PLAY/PAUSE ( ) button once, and the

track “001” will flash. To re sume play, press the CD PLAY/PAUSE ( ) Button again.

5. To stop playing, press the CD STOP( ) Button , then the display will show the total

number tacks of the disc

6. To turn off the CD , rotate the FU NCTION Switch to TAPE or RADIO position.

NOTE: Never press the CD DOOR down during play, this may cause malfunction or

damage the disc. Always stop the CD player by using the CD STOP ( )

Button before you take the disc out of the compartment.

If you hit or move the CD durin g play, the music will stop for a second

or two a nd th en star t aga in. This is normal for portable CD players.

SKIPPING TRACKS (SKIP)

1.This function enables you to find the beginning of any desired track during playback. If

the CD FORWARD/BA CKWARD SKIP(+/-) Button is pressed once or repeatedly, the next

or the back track will be selected. This Display will show the track or song number.

2. If the CD FORWARD/BACKWARD SKIP (+/-) Button is pressed twice or more in rapid

succession, the play will go forward or backward 10 t rack per press.

3. When the set is in the PAUS E mode, it is also possible to select the beginning of a

certain track by using the CD SEARCH SKIP(+ /-) Butto n or CD

FORWARD/BACKWARD SKIP (+/-) Button to reach the desired track . After se lection,

press Play.

4. Press and Hold the FORWARD/BACKWARD SKIP (+ /- )Button to search forward or

backward at a high sp eed for a particular po int. Release the button to resume normal

play when the point is found.

REPEAT PLAY - SINGLE TRA CK (SONG)

To repeat the SAME song over and over again, do the following:

1. When the CD is stopped, press the FORWARD/BACK SKIP Button to select the song

you like.

2. Press the REPEAT Button.

3. The REPEAT Lamp will flash on and off.

Press PLAY B utton.

•Asegúrese de cerrar la puerta del CD para evitar que el lente se ensucie con el polvo.

•No toque el lente.

CÓMO MANIPULAR UN DISCO

CÓMO COLOCAR UN DISCO

1.Coloque el sector de funciones en la posición CD.

2.Presione el botón OPEN (abrir) para abrir la tapa del CD.

3.Inserte un disco con la etiqueta hacia arriba ya que si el disco se coloca de cabeza la pan-

talla mostrará 3 guiones.

4.Cierre la tapa del CD con la mano. La pantalla mostrará 3 guiones y luego el número total de

pistas del disco.

NOTA: Nunca toque el lente láser dentro del compartimiento del CD. Si se ensuciara, límpielo

con un disco limpiador.

Aunque los discos están fabricados para resistir en cierta

medida los efectos del polvo, suciedad y arañones, debe

de tratárselos con cuidado tal como se hace con los

discos análogos de vinilo. Siempre evite que los discos

no se arañen y protéjalos de la suciedad, del polvo, etc.

Recomendamos guardar los discos en sus estuches

originales mientras no estén en uso.

Tenga en cuenta lo siguiente, ya que la suciedad, araño-

nes o desniveles pueden causar sonidos entrecortados o

intermitentes además de ruidos.

•Cuando manipule los discos, preste atención de no

tocar la supercie de reproducción.

•Guarde los discos en sus estuches. Colóquelos en

sus estuches con la parte de la etiqueta hacia arriba y

presione ligeramente.

No coloque los discos en los siguientes lugares:

•Cerca de algún aparato de calor, en un lugar donde la

temperatura sea alta o en lugares con polvo.

•No escriba sobre la supercie con la etiqueta con un

bolígrafo ni pegue otras etiquetas sobre el CD.

•Limpie las huellas digitales en la supercie de reproduc-

ción utilizando un paño suave.

•Tenga en cuanta lo siguiente:

•Siempre limpie desde el centro hacia afuera del disco.

•Nunca limpie en forma circular.

•No utilice limpiadores de discos convencionales, agen-

tes anti estática, bencina, diluente u otros solventes.

NO LOS GUARDE CERCA AL CALOR

LIMPIE DEL CENTRO HACIA AFUERA

MANEJE EL DISCO COMO SE MUESTRA

DO NOT STORE NEAR HEAT

CÓMO RETIRAR UN DISCO

1.Asegúrese de que el disco no se encuentre reproduciéndose. Si fuera así, presione el botón

CD STOP ( ).

2.Presione el botón OPEN para abrir la tapa del CD.

3.Suavemente retire el disco.

4.Cierre de la tapa del CD con la mano.

5.Vuelva a colocar el disco en su estuche protector.

* Be sure to close the CD door, so the lens is not contamina ted by dust.

* Do not touch the lens.

HANDLING A DISC

LOA DING A DISC

1.Set the FUNC TION Switch to the CD position.

2.Press OPEN Button to open the CD Cover.

3.Insert a disc with the label side toward you if the disc is upside down, the Display will

show 3 dashes

4. Close the CD Door by hand.The Display wi ll show 3 dashes and then the total number

of tracks on the disc.

NOTE: Never touch the laser le ns inside the CD compartment. If it eve r gets dirty,

clean it with a CD cleaner disc.

Althou gh built to withstand a certain amount of the effe cts

from dust , soil an d scratches, discs should be treate d with

the care normally accorded to conventional analog discs

(records). Always protect a disc against scratches, soil and

dust etc. We recommend that during non-use periods the

discs should be store d in the original case.

Bear in mind the following points , since any dirt, scratches or

warping of the disc can cause broken or intermittent sound

and also noise.

● When holding the discs, take care not to touch the

playing surface.

● Store the discs in their cases. Return them to their

cases with the label surface facing up and push down

lightly on the label surface.

Do not place discs in the following locations:

Ĵ Near a heating device or a place where the temperature

is high or in dusty areas.

● Do not write on the label surface using a ballpoint pen

and do not stick labels on the MP3 / CD.

● Wipe away any fingerprints or dust on the p laying

surface of a disc using a soft cloth.

● Bear in mind the following points:

Ĵ Alway s wipe from the inside toward the outside of th e

disc.

Ĵ Never in a circular motion.

Ĵ Do not use conventional record clea ners, anti-static

agents, b enzene, thinner or othe r solvents.

REMOV I NG A DISC

1. Make sure the CD is not playing. If it is, press the CD STOP ( ) Button.

2. Press OPEN button to open the CD Do or.

3. Gently remove the disc .

4. Close the CD Door by hand.

5. Replace the disc in its protective storage box.

DISC PLAYING

NORMAL PLAYBACK

1.Set the FUNCTION Switch to CD position and wait about 5 seconds for CD disc will

need longer time (depended on the size & number of tracks of the disc). After the disc

read completely, the Display will then show the total number of tracks on your compact

disc.

2. Press the CD PLAY /PAUSE ( ) Button to start play, The first track number "001" will

appear in the Display an d the disc will start playing ( please wait for about 5 seconds for

mus ic to sta rt ).

3. Ad just the VOLU ME control to the desired volume level.

4.To stop the d isc temporarily, press the CD PLAY/PAUSE ( ) button once, and the

track “001” will flash. To re sume play, press the CD PLAY/PAUSE ( ) Button again.

5. To stop playing, press the CD STOP( ) Button , then the display will show the total

number tacks of the disc

6. To turn off the CD , rotate the FU NCTION Switch to TAPE or RADIO position.

NOTE: Never press the CD DOOR down during play, th is may cause malfunction or