Skyjacker 2.5in Dual Rate Long Travel Lift Kit Guía de instalación

Before beginning the installation, thoroughly & completely read these instructions & the enclosed

driver’s WARNING NOTICE. Affix the WARNING decal in the passenger compartment in clear view

of all occupants. Please refer to the Parts List to insure that all parts & hardware are received prior

to the disassembly of the vehicle. If any parts are found to be missing, contact SKYJACKER®

Customer Service at 318-388-0816 to obtain the needed items. If you have any questions or

reservations about installing this product, contact SKYJACKER® Technical Assistance at 318-388-

0816.

Make sure you park the vehicle on a level concrete or asphalt surface. Many times a vehicle is not

level (side-to-side) from the factory & is usually not noticed until a lift kit has been installed, which

makes the difference more visible. Using a measuring tape, measure the front & rear (both sides)

from the ground up to the center of the fender opening above the axle. Record this information

below for future reference.

Driver Side Front: Passenger Side Front:

Driver Side Rear: Passenger Side Rear:

Important Notes:

• If larger tires (10% more than the OEM diameter) are installed, speedometer recalibration will be

necessary. Contact your local Jeep dealer or an authorized dealer for details.

• After installation, a qualified alignment facility is required to align the vehicle to the OEM

specifications.

1997- 2006 Jeep TJ Wrangler

2.5" - 3" Suspension Lift

Installation Instructions

REQUIRED TOOL LIST:

• Safety Glasses

• Metric / Standard Wrenches & Sockets

• Drill / Assorted Drill Bits

• Floor Jack

• Jack Stands

• Measuring Tape

• Torque Wrench

I-TJ2530 REV2 3-20 Pg 1

www.skyjacker.com

Component Box Breakdown:

Part #: TJ25BPBLT / TJ25BPHLT / TJ25BPMLT / TJ25BPNLT / TJ30BPH

Hardware Bag Breakdown:

Part # HB-TJ25

Item # Description Qty Item # Description Qty

10MMX70MMB 10MM X 70MM METRIC BOLT 4 12FTN 1/2 FINE THREAD LOCK NUT 1

12X70MMB 12MM X 70MM METRIC BOLT 1 12SAEW 1/2 SAE WASHER 3

12MMN 12MM METRIC NUT 1 BPS20-B BUMP STOP SPACER 4

12X112FTB 1/2 X 1 1/2 FINE THREAD BOLT 1 SSTJRTB CRUSH SLEEVE 1

Item # Description Qty Item # Description Qty

TJ25FS-DR TJ FRONT DR/LT COIL SPRING 2 H7016 FRONT HYDRO SHOCK / RED BOOT 2

(Included With TJ25BPBLT, (Included With TJ25BPHLT, TJ30BPH)

TJ25BPHLT, TJ25BPMLT, H7018 REAR HYDRO SHOCK / RED BOOT 2

TJ25BPNLT) (Included With TJ25BPHLT, TJ30BPH)

TJ25RS-DR TJ REAR DR/LT COIL SPRING 2 M9516 M95 MONOTUBE SHOCK 2

(Included With TJ25BPBLT, (Included With TJ25BPMLT)

TJ25BPHLT, TJ25BPMLT, M9518 M95 MONOTUBE SHOCK 2

TJ25BPNLT) (Included With TJ25BPMLT)

TJ30FS TJ FRONT COIL SPRING 2 N8016 NITRO SHOCK / RED BOOT 2

(Included With TJ30BPH) (Included With TJ25BPNLT)

TJ30RS TJ REAR COIL SPRING 2 N8018 NITRO SHOCK / RED BOOT 2

(Included With TJ30BPH) (Included With TJ25BPNLT)

B8516 BLACK MAX SHOCK / BLACK BOOT 2 CAM500 CAM BOLT / UPPER REAR 1

(Included With TJ25BPBLT) TJRTB-B REAR TRACK BAR BRACKET 1

B8518 BLACK MAX SHOCK / BLACK BOOT 2 HB-TJ25 HDWR BAG: HB-TJ25 1

(Included With TJ25BPBLT) I-TJ2530 INST SHT: TJ250 / TJ25/30BPH 1

I-TJ2530 Pg 2

Front Installation:

1. Park the vehicle on a level concrete or asphalt surface, set the

emergency brake & block the rear tires / wheels.

2. Raise the front of the vehicle & support securely using jack stands.

3. Remove the front tires / wheels & OEM front shocks.

4. Disconnect the OEM front track bar from the passenger side axle

bracket. (See Photo # 1)

5. Disconnect the OEM drag link assembly from the OEM pitman arm.

Photo # 1

I-TJ2530 Pg 3

6. Disconnect the OEM sway bar end links from the axle brackets. (See

Photo # 2)

7. While supporting the front axle, lower the front axle until the OEM

front coil springs become loose & remove the OEM bottom bolt & clip

from the left front OEM coil spring. (See Photo # 3)

8. Remove the OEM front coil springs & OEM upper bump stops. Note:

Use channel lock pliers working the OEM bump stop back & forth to

remove.

9. Remove the OEM 10mm bolt from inside the OEM bump stop cups.

Install the new Skyjacker bump stop spacers & OEM bump stop cups

using the supplied 10mm x 70mm bolts. Reinstall the OEM bump

stops in the OEM bump stop cups. (See Photo # 4)

10. Install the new Skyjacker front coil springs & raise the front axle until

enough load is applied to hold the new front coil springs in place.

Reinstall the OEM spring bolt & clip at the bottom of the left front coil

spring.

11. Install the new Skyjacker front shocks using the supplied hardware &

OEM hardware. (See Photo # 5)

12. Attach the OEM drag link to the OEM pitman arm using the OEM

hardware.

13. Attach the OEM sway bar end links to the the axle brackets using the

OEM hardware.

14. Install the front tires / wheels & lower the front of the vehicle to the

ground.

Rear Installation:

15. Block the front tires / wheels, raise the rear of the vehicle, & support

securely using jack stands.

16. Remove the rear tires / wheels & OEM rear shocks.

17. Disconnect the OEM rear track bar & OEM sway bar end links from

the rear axle.

18. While supporting the rear axle, lower the rear axle until the OEM rear

coil springs become loose & remove the OEM rear coil springs & the

OEM upper bump stops. Note: Use channel lock pliers working the

OEM bump stop back & forth to remove.

Photo # 5

Photo # 3

Photo # 4

Photo # 2

Pg 4

19. Remove the OEM 10mm bolt from inside the OEM bump stop cups.

Install the new bump stop spacers & OEM bump stop cups using the

supplied 10mm x 70mm bolts. Reinstall the OEM bump stops in the

OEM bump stop cups. (See Photo # 6)

20. Install the new Skyjacker rear track bar bracket over the OEM rear

track bar bracket & place the OEM rear track bar in the new rear

track bar bracket. Install the supplied 12mm x 70mm bolt through the

OEM lower track bar location using the supplied spacer sleeve,

12mm nut & tighten the bolt to hold the new rear track bar bracket in

place. (See Photo # 7)

21. Drill a 1/2" hole through the hole in the end of the new Skyjacker rear

track bar bracket. Remove the 12mm x 70mm bolt (installed before

drilling) & install the supplied 1/2" x 1 1/2" bolt, with a washer on each

side, through the newly drilled hole & tighten the 1/2" nut. Reinstall

the supplied 12mm x 70mm bolt through the OEM rear track bar

location using the supplied crush sleeve & 12mm nut. Note: Do not

tighten at this time. (See Arrow in Photo # 8)

22. Install the new Skyjacker rear coil springs. Raise the rear axle until

enough load is applied to hold the new rear coil springs in place.

23. Attach the OEM rear track bar to the new Skyjacker rear track bar

bracket using the OEM hardware. Note: Do not tighten at this time.

24. Attach the OEM sway bar end links to the rear axle using the OEM

hardware.

25. Install the new Skyjacker rear shocks using the supplied hardware &

OEM hardware. (See Photo # 9)

26. One side at a time, disconnect the OEM rear upper link from the rear

axle. Note: The OEM hole is notched so it can become a slotted hole.

Knock out the notches on the front & rear half of the OEM hole of the

rear upper link mount. (See Arrows in Photo # 10)

I-TJ2530

Photo # 7

Photo # 8

Photo # 9

Photo # 10

Photo # 6

27. Attach the OEM rear upper link to the rear axle using the supplied

cam bolt, eccentric washers, & nut. Note: Do not tighten at this time.

(See Photo # 11) Repeat Step # 26 & # 27 for the opposite side.

28. Install the rear tires / wheels & lower the rear of the vehicle to the

ground.

29. Tighten the new Skyjacker rear track bar bracket hardware & OEM

rear track bar hardware.

30. Tighten the new Skyjacker rear upper link cam bolts. Note: These new

cam bolts can be rotated to adjust the rear axle pinion angle to

eliminate any driveline vibration.

Final Notes:

• After the installation is complete, double check that all nuts & bolts are tight. Refer to the following

chart for the proper torque specifications. (Do not retighten nuts & bolts where thread lock

compound was used.)

• With the vehicle placed on the ground, cycle the steering lock to lock & inspect the steering,

suspension, brake lines, front & rear drivelines, fuel lines, & wiring harnesses for proper operation,

tightness, & adequate clearance.

• Have the headlights readjusted to the proper settings.

• Have a qualified alignment center realign the vehicle to the OEM specifications.

• After the first 100 miles, check all hardware for the proper torque & periodically thereafter.

Seat Belts Save Lives, Please Wear Your Seat Belt.

Pg 5I-TJ2530

TORQUE SPECIFICATIONS

INCH SYSTEM

Bolt Size Grade 5 Grade 8

5/16 15 FT LB 20 FT LB

3/8 30 FT LB 35 FT LB

7/16 45 FT LB 60 FT LB

1/2 65 FT LB 90 FT LB

9/16 95 FT LB 130 FTLB

5/8 135 FT LB 175 FT LB

3/4 185 FT LB 280 FT LB

METRIC SYSTEM

Bolt Size Class 8.8 Class 10.9

6MM 5 FT LB 9 FT LB

8MM 18 FT LB 23 FT LB

10MM 32 FT LB 45 FT LB

12 MM 55 FT LB 75 FT LB

14MM 85 FT LB 120 FT LB

16MM 130 FT LB 165 FT LB

18MM 170 FT LB 240 FT LB

• The above specifications are not to be used when the bolt is being installed with a bushing.

Photo # 11

Check out our favorite ministries at:

www.innministries.org

www.familychurch.org

www.kcm.org

Jesus Forgives,

Rocks Don’t

Jesus Christ Died For You.

John 3:16

For God so loved the world that He gave His only Son, so that everyone who

believes in Him should not perish, but have everlasting life.

Romans 3:23

For all have sinned; all fall short of God’s glorious standard.

Ephesians 2:8

God saved you by his special favor when you believed. And you can’t take

credit for this; it is a gift from God.

Psalms 18:2

The Lord is my Rock, my fortress, and my savior; my God is my Rock, in

whom I find protection. He is my shield, the strength of my salvation, and

my stronghold.

Romans 10:9-10

That if you shall confess with thy mouth the Lord Jesus, and shall believe in

your heart that God hath raised him from the dead, you shall be saved.

For with the heart man believeth unto righteousness; and with the mouth

confession is made unto salvation.

Pray This Simple Prayer:

God, I come to You admitting I have sinned against You and I need you to

take control of my life. The Bible says anyone who calls on the name of the

Lord will be saved. I am calling on You, Jesus. I ask that You come live in

my heart and be the Lord over my life today. I do believe You died on the

cross for me and came back to life to give me life! Thank You, Lord Jesus

for a new life in You!

Now, go and tell somebody about your new life in Jesus, get a Bible, begin

to read it, and go to a Bible believing church.

If you would like someone to pray with you, call Kenneth Copeland

Ministries anytime at 800-600-7395.

To listen to commercial free Christian radio on the web, go to

www.887fm.org

Juan 3:16

“Porque tanto amó Dios al mundo, que dio a su Hijo unigénito, para que todo

el que cree en él no se pierda, sino que tenga vida eterna.”

Romanos 3:23

“Pues todos han pecado y están privados de la gloria de Dios.”

Efesios 2:8

“Porque por gracia ustedes han sido salvados mediante la fe; esto no procede

de ustedes, sino que es el regalo de Dios.”

Salmos 18:2

“El Señor es mi roca, mi amparo, mi libertador; es mi Dios, el peñasco

en que me refugio. Es mi escudo, el poder que me salva, ¡mi más alto

escondite!”

Romanos 10:9-10

“9 Que si confi esas con tu boca que Jesús es el Señor, y crees en tu corazón

que Dios lo levantó de entre los muertos, serás salvo. 10 Porque con el

corazón se cree para ser justifi cado, pero con la boca se confi esa para ser

salvo.”

Ahora dí esta simple oración:

Dios, vengo a Ti y admito que he pecado contra Ti, necesito que tomes el

control de mi vida. La Biblia dice que todo aquel que invoca el nombre del

Señor escapará con vida. En este momento yo clamo ante Ti, Jesús; te pido

que vengas a vivir en mi corazón y que tomes el control de mi vida. ¡Yo creo

que tu moriste en la cruz y resucitaste para darme vida! ¡Gracias Señor Jesús,

por una nueva vida que tengo en Ti! Amen.

Ahora ve y dile a alguien sobre la nueva vida que tienes en Cristo. Compra

una Biblia y empieza a leerla. Busca una Iglesia que cree en la Biblia y hazte

parte de esa Iglesia.

Si te gustaría orar con alguien, puedes llamar a este número 800-600-7395

Puedes ir a este sitio de Internet para escuchar música Cristiana sin anuncios,

www.887fm.org

Jesús murió por ti.

www.skyjacker.com

Skyjacker 2.5in Dual Rate Long Travel Lift Kit Guía de instalación

Skyjacker 2.5in Dual Rate Long Travel Lift Kit Guía de instalación

En otros idiomas

Documentos relacionados

Otros documentos