Black Horse Model BH129 Manual de usuario
- Categoría
- Juguetes
- Tipo
- Manual de usuario
SPECIFICATION
Instruction Manual book
Wingspan : 2,200 mm 86.61 in.
Length : 1,760 mm 69.29 in.
Weight : 7.4 kg 16.28 Lbs.
Parts listing required (not included)
Radio : 07 channes.
Servo : 09 Standard high torque servos.
Engine : O.S GT 22-33 CC Gas.
Made in Vietnam.
Item code:BH129
2
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
This instruction manual is designed to help you build a great flying aeroplane. Please read this
manual thoroughly before starting assembly of your Jodel Robin DR400. Use the parts listing below
to identify all parts.
WARNING.
Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is
capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & RESPONSIBILITY.
If you are inexperienced with basic R/C flight we strongly recommend you contact your R/C supplier
and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training
procedures designed to help the new pilot on his way to successful R/C flight. They will also be able
to advise on any insurance and safety regulations that may apply.
TOOLS & SUPPLIES NEEDED.
Thick cyanoacrylate glue.
30 minute epoxy.
5 minute epoxy.
Hand or electric drill.
Assorted drill bits.
Modelling knife.
Straight edge ruler.
2mm ball driver.
Phillips head screwdriver.
220 grit sandpaper.
90° square or builder’s triangle.
Wire cutters.
Masking tape & T-pins.
Thread-lock.
Paper towels.
Some more parts.
HARDWARE PACK
COWLING.
Landing gear.....
To avoid scratching your new airplane, do not
unwrap the pieces until they are needed for
assembly. Cover your workbench with an old
towel or brown paper, both to protect the air-
craft and to protect the table. Keep a couple of
jars or bowls handy to hold the small parts af-
ter you open the bag.
Please trial fit all the parts. Make sure you have
the correct parts and that they fit and are
aligned properly before gluing! This will assure
proper assembly.
Jodel Robin DR400 ARF is
hand made from natural materials, every plane
is unique and minor adjustments may have to
be made. However, you should find the fit su-
perior and assembly simple.
The painted and plastic parts used in this kit
are fuel proof. However, they are not tolerant
of many harsh chemicals including the follow-
ing: paint thinner, C/A glue accelerator, C/A glue
debonder and acetone. Do not let these chemi-
cals come in contact with the colors on the
covering and the plastic parts.
PARTS LISTING.
FUSELAGE ASSEMBLY
(1) Fuselage.
WING ASSEMBLY
(1) Right wing half with pre-installed
aileron.
(1) Left wing half with pre-installed
aileron.
Tail section assembly
(1) Vertical stabilizer with pre-
installed rudder.
(1) Horizontal stabilizer with pre-
installed elevator halves.
SUGGESTION.
NOTE.
3
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
Caution: this model is not a toy!
If you are a beginner to this type of powered model, please ask an experienced model flyer for help
and support. If you attempt to operate the model without knowing what you are doing you could
easily injure yourself or somebody else. Please keep your safety and well-being in mind at all
times.
Important: before you start construction
Even if you have already built a large number of RC models please read right through these
instructions and check all the kit components against the parts list. We have taken great trouble to
keep construction as simple as possible, without making any compromises in the area of safety.
Note regarding the film covering
Minor creases or bubbles may develop in the film covering due to major fluctuations in weather
conditions (temperature, humidity etc.); in rare cases you may even find a slight warp in a
component. These minor faults are in the nature of film-covered built-up wooden structures, and
can easily be corrected using a heat gun, as commonly used for modelling.
Creases: Blow warm air over the area and rub down with a soft cloth.
Wing warp: Hold the panel twisted gently in the opposite direction to the warp, and apply
warm air to remove the creases from the covering.
Caution! do not heat the film more than is absolutely necessary. If the air or the iron is too hot, the
film may melt and holes may be formed.
This model is highly pre-fabricated and can be built in a very short time. However, the work which
you have to carry out is important and must be done carefully. The model will only be strong and fly
well if you complete your tasks competently - so please work slowly and accurately.
When self-tapping screws have to be screwed into wood, apply a little white glue to prevent
them shaking loose: just squirt white glue into the hole and fit the screw.
+ This is not a toy
+ Be sure that no other flyers are using your radio frequency.
+ Do not smoke near fuel
+ Store fuel in a cool, dry place, away from children and pets.
+ Wear safety glasses.
+The glow plug clip must be securely attached to the glow plug.
+ Do not flip the propeller with your fingers.
+ Keep loose clothing and wires away from the propeller.
+ Do not start the engine if people are near. Do not stand in line with the side of the propeller.
+ Make engine adjustments from behind the propeller only. Do not reach around the spinning pro-
peller.
SAFETY PRECAUTION.
4
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
REPLACEMENT LARGE PARTS
5. Fuel tank.
REPLACEMENT SMALL PARTS
9.Plastic parts for elevator and rudder pushrod.
7. Antenna
4. Wheels.
1.Oleo struts landing gear.
2.Oleo strut nose gear.
3a.Wheel pant (Right)
6. Spinner.
F1. Aluminium tube wing.
E. Rudder
G. Decal sheets.
A.Cowling.
B.Wing panel(B1&B2).
C.Fuselage.
D.Horizontal stabilizer.
F2. Aluminium tube horizontal stabilizer.
3b.Wheel pant (Left )
3c.Wheel pant (nose)
8a.Fairing plastic for wing (right).
8b.Fairing plastic for wing (Left).
K.Pilot
1.
2.
4x15mm.
4x15mm.
4.
4.
5.
7.
8a.
6.
5x40mm.
3a.
3c.
9.
4x8mm.
3b.
4x8mm.
3x20mm.
8b.
B2.
B1.
C.
A.
F1.
E.
D2.
D1.
G.
F2.
A.
B.
K
5
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
1) Install the rubber grommets and brass
eyelets onto the aileron servos.
2. Using a modeling knife, remove the cov-
ering servo tray.
1.INSTALLING THE AILERON SERVOS.
Bottom side
Aileron
Top side
Remove
covering.
4. Drill 1,5mm pilot holes through the block
of wood for each of the four mounting screws
provided with the servo.
Install servo into aileron servo tray as same
as picture below.
Electric wire
Thread
Servo tray.
I. AILERON.
3) Using the thread as a guide and using
masking tape, tape the servo lead to the end
of the thread: carefully pull the thread out.
When you have pulled the servo lead out, re-
move the masking tape and the servo lead
from the thread.
Secure.
Servo tray.
Servo tray.
6
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
Aileron control horn
Repeat the procedure for the other wing
half.
Secure
A+B Epoxy
PLUS glue
A
B
INSTALLING THE AILERON CONTROL HORN.
A+B Epoxy
PLUS glue
Installing the aileron linkages as pictures
below.
INSTALLING THE AILERON
LINKAGES.
2x10mm.
Repeat the procedure for the other wing
half.
Control horn of
the aileron.
M3
M3 lock nut
70mm
3x15 mm
7
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
Secure.
Repeat the procedure for the other wing
half.
II. FLAP SERVO.
1.INSTALLING THE FLAP SERVOS.
Thread
Electric wire
Secure.
2x10mm.
Flap
8
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
Installing the flap linkages as pictures
below.
A+B Epoxy
PLUS glue
3. INSTALLING THE FLAP
LINKAGES.
Flap control
horn.
Flap control horn
2.INSTALLING THE FLAP CONTROL HORN.
M3
M3 lock nut
70mm
3x15 mm
Secure.
4x12mm
9
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
Repeat the procedure for the other wing
half.
Flap
Aileron
Secure
4x15mm
4x15mm
4x8mm
5x40mm
PARTS REQUIRED
MAIN GEAR INSTALATION.
4x15mm 4x8mm
4x 15mm
10
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
Secure.
4x 8mm
Secure.
Drill a hole
7mm
hole 7mm
5x 40mm
11
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
Repeat the procedure for the other gear.
Bottom side.
Secure
Secure.
Drill a hole
5mm diameter
Secure.
See pictures below:
INSTALLING THE ENGINE MOUNT.
5x 70mm
12
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
INSTALLING THE THROTTLE CABLE.
1. Install one adjustable metal connector
through the third hole out from the center of
one servo arm, enlarge the hole in the servo
arm using a 2mm drill bit to accommodate the
servo connector. Remove the excess mate-
rial from the arm.
After installing the adjustable metal con-
nector apply a small drop of thin C/A to
the bottom nut. This will prevent the con-
nector from loosening during flight.
Front view.
Throttle cable.
Throttle Servo.
Cut off the excess cable.
Throttle cable.
4. Carefully bend the third nylon tube down
at a 45 degree angle (using a cigarette lighter).
This tube will be vent tube to the fueling valve.
3. Carefully bend the second nylon tube up
at a 45 degree angle (using a cigarette lighter).
This tube will be the vent tube to the muffler.
INSTALLING THE STOPPER ASSEMBLY
1. The stopper has been pre-assembled at
the factory.
2. Using a modeling knife, cut one length of
silicon fuel line (the length of silicon fuel line is
calculated by how the weighted clunk should
rest about 8mm away from the rear of the tank
and move freely inside the tank). Connect one
end of the line to the weighted clunk and the
other end to the nylon pick up tube in the stop-
per.
FUEL TANK.
13
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
When the stopper assembly is installed in the
tank, the top of the vent tube should rest just
below the top surface of the tank. It should not
touch the top of the tank.
Tygon gas tubing not included.
Vent tube
Fuel pick- up tube
Fuel fill tube
5) Test fit the stopper assembly into the
tank. It may be necessary to remove some of
the flashing around the tank opening using
a modeling knife. If flashing is present, make
sure none of it falls into the tank.
6) When satisfied with the alignment of
the stopper assembly tighten the 3mm x 20mm
machine screw until the rubber stopper ex-
pands and seals the tank opening. Do not over
tighten the assembly as this could cause the
tank to split.
7) Using a modeling knife, cut 3 lengths of
fuel line 150mm long. Connect 2 lines to the 2
vent tubes and 1 line to the fuel pickup tube in
the stopper.
8) Feed three lines through the fuel tank
compartment and through the pre-drilled hole
in the firewall. Pull the lines out from behind
the engine, while guiding the fuel tank into
place. Push the fuel tank as far forward as
possible, the front of the tank should just about
touch the back of the firewall.
Blow through one of the lines to ensure
the fuel lines have not become kinked inside
the fuel tank compartment. Air should flow
through easily.
9) To secure the fuel tank in place, apply a
bead of silicon sealer to the forward area of
the tank, where it exits the fuselage behind the
engine mounting box and to the rear of the tank
at the forward bulkhead.
Do not secure the tank into place perma-
nently until after balancing the airplane. You
may need to remove the tank to mount the
battery in the fuel tank compartment
14
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
M2
pushrod choke.
pushrod choke.
Left side.
Right side.
Tie wrap.
Fuel tank.
15
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
Bottom side.
Front view.
INSTALLING THE NOSE GEAR.
See pictures below:
3x 20mm
4x8mm
5x 40mm
3x20mm
Secure.
Silicon
16
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
Secure
Drill a hole
7mm.
5x 40mm
Secure.
Servo nose
gear.
Secure.
INSTALLING THE SERVO NOSE GEAR.
17
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
Servo nose gear.
Pull-Pull cable
wire.
Pull-Pull cable
wire.
Pull-Pull cable
wire.
cut off the
excess cable.
18
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
1. Slide the fiberglass cowl over the en-
gine and line up the back edge of the cowl with
the marks you made on the fuselage.
2. While keeping the back edge of the
cowl flush with the marks, align the front of
the cowl with the crankshaft of the engine. The
front of the cowl should be positioned so the
crankshaft is in nearly the middle of the cowl
opening. Hold the cowl firmly in place using
pieces of masking tape.
3. Slide the cowl back over the engine
and secure it in place using four wood screws.
See picture below.
4. Install the muffler and muffler extension
onto the engine and make the cutout in the
cowl for muffler clearance. Connect the fuel
and pressure lines to the carburetor, muffler
and fuel filler valve.
COWLING.
Top side
bottom side.
Left side.
Trim and cut.
Left wing.
Bottom side.
Drill a hole
2.5mm
19
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
3 x 12mm
Secure
Machine screw
Install the spinner backplate, propeller and
spinner cone. The spinner cone is held in
place using two 3mm x 8mm machine screws.
Front view.
INSTALLING THE SPINNER.
Secure.
Secure.
20
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
2. Mount the servo to the tray using the
mounting screws provided with your radio sys-
tem.
1. Install the rubber grommets and brass
collets into the elevator servo. Test fit the servo
into the servo tray.
ELEVATOR SERVO INSTALLATION.
Elevator servo
Horizontal stabilizer installation .
See picture below.
Elevator servo
Elevator servo
Secure
Elevator control horn install as same as the
way of aileron control horn. Please see pic-
tures below.
Control horn of elevator
ELEVATOR CONTROL HORN INSTALLA-
TION.
4x12mm
HORIZONTAL STABILIZER
INSTALLATION.
21
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
A+B Epoxy
PLUS glue
305 mm
12 mm
Bottom side
Bottom side
Elevator
control horn
Elevator
control horn
22
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
Secure.
M3
M3 lock nut
Elevator pushrod install as same as the way
of aileron pushrod.
ELEVATOR PUSHROD INSTALLATION.
Rudder servo install as same as method of
elevator servo. See picture below:
Elevator
pushrod.
Rudder
servo
RUDDER INSTALLATION.
Bottom side.
Bottom side
Elevator
pushrod.
Elevator
pushrod.
M3
M3 lock nut
23
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
Rudder control horn install as same as the
way of aileron control horn. Please see pic-
tures below.
Control horn of Rudder.
Rudder servo
Elevator pushrod.
Elevator pushrod.
Aluminium.
Top side
Push.
Cut off the excess.
RUDDER CONTROL HORN
INSTALLATION.
A+BEpoxy
PLUS glue.
24
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
1. Rudder push - pull system install as
same as picture below.
RUDDER PUSHROD INSTALLATION.
A+B
Epoxy PLUS glue.
Rudder
control horn.
3x15mm
Secure.
Plastic parts of elevator and
rudder pushrod.
Elevator
pushrod
Rudder
cable.
Botom side
Cut.
25
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
C/A glue.
C/A glue
Bottom side.
cut
rudder cable.
Elevator pushrod.
Elevator pushrod.
1. Cut out the switch hole using a modeling
knife. Use a 2mm drill bit and drill out the two
mounting holes through the fuselage side.
2. Secure the switch in place using the
two machine screws provided with the radio
system.
INSTALLING THE SWITCH.
switch
switch of
engine
switch of
receiver.
26
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
1. Plug the servo leads and the switch
lead into the receiver. You may want to plug
an aileron extension into the receiver to make
plugging in the aileron servo lead easier
when you are installing the wing . Plug the
battery pack lead into the switch.
2. Wrap the receiver and battery pack in
the protective foam to protect them from vi-
bration. Use a rubber band or masking tape to
hold the foam in place.
3. Position the battery pack and receiver
behind the fuel tank. Use the two light plywood
pieces, placed over the battery and receiver
and glue to the fuselage sides to hold the bat-
tery and receiver securely in place. Use 15mm
triangle pieces glued between the fuselage
sides and the plywood pieces to reinforce the
joints.
Do not permanently secure the receiver and
battery until after balancing the model.
4. Using a 2mm drill bit, drill a hole through
the side of the fuselage, near the receiver, for
the antenna to exit.
INSTALLING THE RECEIVER AND BATTERY.
receiver
Tie wrap.
Battery of
receiver.
Battery of engine.
Locate the aluminium wing dihedral brace.
*** Test fit the aluminium tube dihedral brace
into each wing haft. The brace should slide in
easily. If not, use 220 grit sand around the
edges and ends of the brace until it fits prop-
erly.
WING ATTACHMENT.
32mm
790mm
Right wing.
Push.
27
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
Left wing.
Secure.
INSTALLING THE TOW SERVO.
Tow servo.
28
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
Secure.
Top side.
Plastic parts for Fairing
7. Antenna
8a.
8b.
29
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
C/A glue.
1) It is critical that your airplane be bal-
anced correctly. Improper balance will cause
your plane to lose control and crash.
THE CENTER OF GRAVITY IS LOCATED
114 MM BACK FROM THE LEADING EDGE
OF THE WING.
2) Mount the wing to the fuselage. Using a
couple of pieces of masking tape, place them
on the top side of the wing 114 mm back from
the leading edge, at the fuselage sides.
3. Turn the airplane upside down. Place
your fingers on the masking tape and care-
fully lift the plane .
BALANCING.
30
JODEL ROBIN DR400 - Item code: BH129 . INSTRUCTION MANUAL
Accurately mark the balance point on the top
of the wing on both sides of the fuselage. The
balance point is located 114 mm back from
the leading edge. This is the balance point at
which your model should balance for your first
flights. Later, you may wish to experiment by
shifting the balance up to 10mm forward or
back to change the flying characteristics. Mov-
ing the balance forward may improve the
smoothness and arrow- like tracking, but it may
then require more speed for take off and make
it more difficult to slow down for landing. Mov-
ing the balance aft makes the model more agile
with a lighter and snappier ”feel”. In any case,
please start at the location we recommend .
With the wing attached to the fuselage, all
parts of the model installed ( ready to fly), and
empty fuel tanks, hold the model at the
marked balance point with the stabilizer level.
Lift the model. If the tail drops when you
lift, the model is “tail heavy” and you must add
weigh* to the nose. If the nose drops, it is “nose
heavy” and you must add weight* to the tail to
balance.
*If possible, first attempt to balance the model
by changing the position of the receiver bat-
tery and receiver. If you are unable to obtain
good balance by doing so, then it will be nec-
essary to add weight to the nose or tail to
achieve the proper balance point.
1) Completely charge your transmitter and
receiver batteries before your first day of fly-
ing.
2) Check every bolt and every glue joint in
your plane to ensure that everything is tight
and well bonded.
3) Double check the balance of the
airplane.
4) Check the control surface.
5) Check the receiver antenna . It should
be fully extended and not coiled up inside the
fuselage.
6) Properly balance the propeller.
Ailerons : 15 mm up 15 mm down
Flap : 30 mm
Elevator : 15mm up 15mm down
Rudder : 20mm right 20 mm left
1) We highly recommend setting up a
plane using the control throws listed.
2) The control throws should be meas-
ured at the widest point of each control sur-
face.
3) Check to be sure the control surfaces
move in the correct directions.
CONTROL THROWS.
PRE-FLIGHT CHECK.
Flap control
Aileron control
Elevator control
Rudder control
15 mm
15mm
15mm
15mm
30mm
20mm
20mm
We wish you many safe and enjoyable
flights with your Jodel Robin DR400.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
Black Horse Model BH129 Manual de usuario
- Categoría
- Juguetes
- Tipo
- Manual de usuario
en otros idiomas
- English: Black Horse Model BH129 User manual
Artículos relacionados
Otros documentos
-
Merlin CESSNA T-206 Manual de usuario
-
Merlin pilot 500 Manual de usuario
-
-
MULTIPLEX 21 4193 Building Instructions
-
-
-
-
-
Cessna 150 1969 El manual del propietario