Moog FusionDome PFDW75T2N Installation And Operation Instructions Manual

Marca: Moog

Modelo: FusionDome PFDW75T2N

Categoría: Accesorios para cámaras de seguridad

Tipo: Installation And Operation Instructions Manual

Este manual también es adecuado para

PFDW75C2N

El Moog FusionDome PFDW75T2N es una carcasa de domo presurizada para exteriores de 7 pulgadas lista para red IP con un montaje en pared de cuello de cisne WM20G, con entrada de 24 Vca, calentador y soplador, para cámaras de red, transformador de 120 a 24 Vca, 96 vA, domo tintado. Está diseñado para usarse con cámaras de red y proporciona un entorno protegido para la cámara, incluso en condiciones climáticas adversas. El domo tintado ayuda a reducir el deslumbramiento y mejora la visibilidad en condiciones de luz brillante.

Moog Inc.

Sensor and Surveillance Systems

3650 Woodhead Drive Northbrook, IL. USA 60062

+1.847.498.0700 Fax: +1.847.498.1258 www.moogS3.com

PFDW75C2N

Pressurized FusionDome™ Network Outdoor Wall Mounted Camera Enclosure

PFDW75C2N............. IP Network Ready 7” outdoor pressurized dome housing with WM20G gooseneck wall mount, with 24Vac input, heater and blower, for

Network cameras, 120 to 24Vac, 96vA transformer, clear dome

PFDW75T2N.............. IP Network Ready 7” outdoor pressurized dome housing with WM20G gooseneck wall mount, with 24Vac input, heater and blower, for

Network cameras, 120 to 24Vac, 96vA transformer, tinted dome

PFDW78C2N.............. An extended trim ring model for larger cameras with a maximum camera depthof 243.3mm (9.58”)

Substitute “C” (Clear dome) for “T” (Tinted dome) version

To be used with the 81-IN5481 Instruction Manual.

Installation and Operation Instructions

Before attempting to connect or operate this product, please

read these instructions completely.

IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS

UNPACKING

SERVICE

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with damp cloth.

7 Do not block any of the ventilation openings. Install in accordance with the

manufacturers instructions.

8 Cable Runs- All cable runs must be within permissible distance.

9 Mounting - This unit must be properly and securely mounted to a supporting

structure capable of sustaining the weight of the unit.

Accordingly:

a. This installation should be made by a qualied service person and should conform

to all local codes.

b. Care should be exercised to select suitable hardware to install the unit, taking into

account both the composition of the mounting surface and the weight of the unit.

10 Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus ( including ampliers) that produce heat.

11 Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wide blade or the third

prong are provided for your safety. When the provided plug does not t into your

outlet, consult an electrician for replacement of the obsolete outlet.

12 Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

13 Only use attachment/ accessories specied by the manufacturer.

14 Use only with a cart, stand, tripod, bracket, or table specied by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

15 Unplug this apparatus during lighting storms or when unused for long periods of time.

16 Refer all servicing to qualied service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled of objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or

has been dropped.

Be sure to periodically examine the unit and the supporting structure to make sure that the integrity

of the installation is intact. Failure to comply with the foregoing could result in the unit separating

from the support structure and falling, with resultant damages or injury to anyone or anything struck

by the falling unit.

Unpack carefully. Electronic components can be

damaged if improperly handled or dropped. If an item

appears to have been damaged in shipment, replace

it properly in its carton and notify the shipper.

Be sure to save:

1 The shipping carton and packaging material.

They are the safest material in which to make future

shipments of the equipment.

2 These Installation and Operating Instructions.

If technical support or service is needed, contact us at

the following number:

The lightning ash with an arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of non-insulated

“dangerous voltage” within the product’s

enclosure that may be of sufcient magnitude

to constitute a risk to persons.

Este símbolo se piensa para alertar al usuario a la presencia

del “voltaje peligroso no-aisIado” dentro del recinto de los

productos que puede ser un riesgo de choque eléctrico.

Ce symbole est prévu pour alerter I’utilisateur à la presence

“de la tension dangereuse” non-isolée dans la clôture de

produits qui peut être un risque de choc électrique.

Dieses Symbol soll den Benutzer zum Vorhandensein der

nicht-lsolier “Gefährdungsspannung” innerhalb der

Produkteinschließung alarmieren die eine Gefahr des

elektrischen Schlages sein kann.

Este símbolo é pretendido alertar o usuário à presença “di

tensão perigosa non-isolada” dentro do cerco dos produtos

que pode ser um risco de choque elétrico.

Questo simbolo è inteso per avvertire I’utente alla presenza

“di tensione pericolosa” non-isolata all’interno della

recinzione dei prodotti che può essere un rischio di scossa

elettrica

The exclamation point within an equilateral

triangle is intended to alert the user to

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

Este símbolo del punto del exclamation se piensa para

alertar al usuario a la presencia de instrucciones importantes

en la literatura que acompaña la aplicación.

Ce symbole de point d’exclamation est prévu pour alerter

l’utilisateur à la presence des instructions importantes dans

la littérature accompagnant l’appareil.

Dieses Ausruf Punktsymbol soll den Benutzer zum

Vorhandensein de wichtigen Anweisungen in der Literatur

alarmieren, die das Gerät begleitet.

Este símbolo do ponto do exclamation é pretendido alertar o

usuário à presença de instruções importantes na literatura

que acompanha o dispositivo.

Questo simbolo del punto del exclamaton è inteso per

avvertire l’utente alla presenza delle istruzioni importanti nella

letteratura che accompagna l'apparecchio.

TECHNICAL SUPPORT

AVAILABLE 24 HOURS

1- 800-554 -1124

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER ( OR BACK). NO USER- SERVICE-

ABLE PARTS INSIDE. REFER SEVICING

TO QUALIFIED SERVICE PERSONNEL.

MADEIN

BUY AMERICA COMPLIANT • COUNTRY OF ORIGIN U.S.A.

USA

Product Warranty Registration

www.moogS3.com/technical-support/product-registration

Moog values your patronage. We are solely committed to providing you with the highest quality products and

superior customer service. With 3-Year and 5-Year warranties (depending on the product purchased) we stand

behind every product we sell.

• Simple and Trouble-Free RMA process

• Product / software updates

• Special promotions

• Eliminate the need to archive purchase documents such as receipts, purchase orders, etc.

See full warranty details at www.moogS3.com/technical-support/warranty-plan/

Limited Warranty for Moog Products

Moog - Decatur Operations, subsequently referred to as “Manufacturer,” warrants these products to be free from defects in material or workmanship as follows:

During the labor warranty period, to repair the Product, Purchaser will either return the defective product, freight prepaid, or deliver it to Manufacturer at Moog Decatur

Operations, 2525 Park Central Boulevard, Decatur, Georgia, 30035. The Product to be repaired is to be returned in either its original carton or a similar package affording

an equal degree of protection with a RMA # (Return Materials Authorization number) displayed on the outer box or packing slip. To obtain a RMA# you must contact our

Technical Support Team at 800.554.1124, extension 101. Manufacturer will return the repaired product freight prepaid to Purchaser. Manufacturer is not obligated to

provide Purchaser with a substitute unit during the warranty period or at any time. After the applicable warranty period, Purchaser must pay all labor and/or parts charges.

The limited warranty stated in these product instructions is subject to all of the following terms and conditions.

TERMS AND CONDITIONS

1. NOTIFICATION OF CLAIMS: WARRANTY SERVICE: If Purchaser believes that the Product is defective in material or workmanship, then written notice with an explanation

of the claim shall be given promptly by Purchaser to Manufacturer. All claims for warranty service must be made within the warranty period. If after investigation,

Manufacturer determines the reported problem was not covered by the warranty, Purchaser shall pay Manufacturer for the cost of investigating the problem at its then

prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall extend the warranty period of the entire Product. The specic warranty on

the repaired part only shall be in effect for a period of ninety (90) days following the repair or replacement of that part or the remaining period of the Product parts warranty,

whichever is greater.

2. EXCLUSIVE REMEDY: ACCEPTANCE: Purchaser’s exclusive remedy and Manufacturer’s sole obligation is to supply (or pay for) all labor necessary to repair any Product

found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts.

3. EXCEPTIONS TO LIMITED WARRANTY: Manufacturer shall have no liability or obligation to Purchaser with respect to any Product requiring service during the warranty

period which is subjected to any of the following: abuse, improper use, negligence, accident, or acts of God (i.e., hurricanes, earthquakes), modication, failure of the

end-user to follow the directions outlined in the product instructions, failure of the end-user to follow the maintenance procedures recommended by the International Security

Industry Organization, written in product instructions, or recommended in the service manual for the Product. Furthermore, Manufacturer shall have no liability where a

schedule is specied for regular replacement or maintenance or cleaning of certain parts (based on usage) and the end-user has failed to follow such schedule; attempted

repair by non-qualied personnel; operation of the Product outside of the published environmental and electrical parameters, or if such Product’s original identication

(trademark, serial number) markings have been defaced, altered, or removed. Manufacturer excludes from warranty coverage Products sold AS IS and/or WITH ALL FAULTS

and excludes used Products which have not been sold by Manufacturer to the Purchaser. All software and accompanying documentation furnished with, or as part of the

Product is furnished “AS IS” (i.e., without any warranty of any kind), except where expressly provided otherwise in any documentation or license agreement furnished with

the Product. ANY COST ASSOCIATED WITH REMOVAL OF DEFECTIVE PRODUCT AND INSTALLATION OF REPLACEMENT PRODUCT IS NOT INCLUDED IN THIS WARRANTY.

4. PROOF OF PURCHASE: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.

PRODUCT CATEGORY PARTS \ LABOR

All Enclosures and Electronics Five (5) Years

Accessory Brackets Five (5) Years

Controllers Three (3) Years

Power Supplies / IR Illuminators Three (3) Years

Poles / PolEvators™ / CamEvator Three (3) Years

Warrior Series™ / Q-View™Three (3) Years

SView Series™Three (3) Years 6 months if used in auto scan / tour operation

DeputyDome™, NiteTrac™, Igloo Dome, PurgeDome™Three (3) Years 6 months if used in auto scan / tour operation

EXO Series™ Dome and Fixed Camera Systems* Three (3) Years 6 months if used in auto scan / tour operation

EXO Series™ GeminEye Visible and Thermal Camera Systems One (1) Year

DISCLAIMER OF WARRANTY

EXCEPT FOR THE FOREGOING WARRANTIES, MANUFACTURER HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT

NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY WARRANTY WITH REGARD TO ANY

CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL CODE AND/OR IN ANY OTHER COMPARABLE STATE STATUTE.

MANUFACTURER HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-MANUFACTURER

PRODUCTS OR NON-MANUFACTURER RECOMMENDED PRODUCTS PURCHASER MAY CHOOSE TO CONNECT TO THE PRODUCT.

LIMITATION OF LIABILITY

THE LIABILITY OF Manufacturer, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER, REGARDLESS

OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE PRODUCT WITH RESPECT

TO WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL MANUFACTURER BE LIABLE TO PURCHASER FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL

DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION, REPLACEMENT LABOR COSTS, REIMBURSEMENT, OR DAMAGES ON ACCOUNT OF THE LOSS

OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.

* NOTE

Moog will repair or replace, at its option, any equipment which is damaged by transient voltage surge/spike or lightning strike (an “Occurrence”), while properly connected

to wired AC power line with protective ground. Any repair or modication of the equipment done by someone other than Moog voids the warranty.

Form 500-911 081913

24 VAC

3.3 Amps

Total Power: 80 Watts

Accessories: Heater: 50 Watts/Blower: 2 Watts

Camera Power: 28 Watts Max

Tools Required: .100” Flat Head Screwdriver

Phillips Head Screwdriver

7/16” Wrench or Socket

24 VAC

3.3 amperios

Energía Total: 80 vatios

Accesorios: Calentador: 50 Watts/Blower: 2 vatio

Energía De la Cámara fotográfica: 28 vatios Max

Las Herramientas Requirieron: Destornillador Principal Plano Del 100"

Destornillador Principal Phillips

24 VCA

3.3 ampères

Puissance Totale : 80 watts

Accessoires : Réchauffeur : 50 Watts/Blower : 2 watts

Puissance D'Appareil-photo : 28 watts Max

Les Outils besoin : Tournevis Principal Plat De 100"

Tournevis Principal Phillips

24 VAC

3.3 Ampere

Gesamtenergie: 80 Watt

Zusatzgeräte: Heizung: 50 Watt/Blower: 2 Watt

Kamera-Energie: 28 watts Max

Werkzeuge Erforderten: 100"Flacher Hauptschraubenzieher

Kreuzkopfhauptschraubenzieher

24 VAC

3.3 ampères

Poder Total: 80 watts

Acessórios: Calefator: 50 Watts/Blower: 2 watt

Poder Da Câmera: 28 watts Max

As Ferramentas Requereram: Chave de fenda Principal Lisa Do 100"

Chave de fenda Principal Phillips

24 VAC

3.3 ampère

Alimentazione Totale: 80 watt

Accessori: Riscaldatore: 50 Watts/Blower: 2 watt

Alimentazione Della

Macchina fotografica: 28 watts Max

Attrezzi Richiesti: Cacciavite Capo Piano Del 100"

Cacciavite Capo "phillips"

Electrical Specifications

Power 24VAC

Class 2 Only

PFDW75C2N

Français

Deutsch

Italiano

Portuguese

Español

English

Contents of Box

*** Pan Tilt boxed separately along with its instructions.

Securely mount bracket to wall. Pull wiring

through bracket and position grommet as shown.

• Con seguridad soporte del montaje a emparedar. Tire del cableado

a través del soporte y del ojal de la posición según lo demostrado.

• Solidement parenthèse de bâti à murer. Tirez le câblage par la

parenthèse et le canon isolant de position comme montré.

• Sicher Einfassung Haltewinkel wall. Ziehen Sie Verdrahtung durch

Haltewinkel und Position Gummimuffe, wie gezeigt.

• Firmemente suporte da montagem a wall. Puxe a fiação através do

suporte e do ilhó da posição como mostrado.

• Saldamente staffa del supporto da wall. Tiri i collegamenti tramite la

staffa ed il gommino di protezione di posizione come indicato.

Screw the (2) bolts into the coupling.

• Atornille (2) los pernos en el acoplador.

• Vissez (2) les boulons dans l'accouplement.

• Schrauben Sie die (2) Schraubbolzen in die

Koppelung.

• Parafuse (2) os parafusos no acoplamento.

• Avviti (2) i bulloni nell'accoppiamento.

Teflon tape™ is wrapped around the pipe threads to

ensure a tight seal and to prevent galling.

• Cinta de Teon ™ se envuelve alrededor de las roscas de la tubería para

asegurar un sello hermético y para evitar el gripado.

• Ruban téon ™ est enroulé autour des letages pour assurer une bonne

étanchéité et éviter tout grippage.

• Teonband ™ ist rund um die Rohrgewinde gewickelt, um eine Abdichtung

zu gewährleisten und zu verhindern Fressen.

• Fita de Teon ™ é enrolado em torno das roscas do tubo para assegurar uma

selagem apertada e para evitar escoriações.

• Teon ™ nastro è avvolto intorno le lettature per assicurare una buona tenuta

e per prevenire l'usura.

•Special anti-seize tape

“DO NOT REMOVE”

Screw the coupling tightly onto the pipe threads by

inserting a screwdriver through slots in coupling to

ease in final tightening.

• Atornillar el acoplamiento rmemente en las roscas de las tuberías mediante la inserción de un

destornillador a través de las ranuras de acoplamiento para facilitar el apriete nal.

• Vissez le couplage serré sur le letage de tuyaux en insérant un tournevis dans les fentes de

couplage à l'aise dans le serrage nal.

• Schrauben Sie die Kupplung fest auf die Rohrgewinde durch Einführen eines Schraubendrehers

durch die Schlitze in der Kopplung in dem endgültigen Anziehen zu erleichtern.

• Parafuse o acoplamento bem para as roscas pela inserção de uma chave de fenda através

ranhuras para facilitar o acoplamento no aperto nal.

• Avvitare l'attacco saldamente sulle lettature inserendo un cacciavite nelle fessure di

accoppiamento ad allentarsi nel serraggio nale.

Loop the lanyard over the screw

head to temporarily hold housing.

• Loop la cuerda de seguridad en la cabeza del tornillo para mantener

temporalmente la vivienda.

• Enroulez le cordon autour de la tête de vis pour maintenir temporairement

le logement.

• Loop the Lanyard über den Schraubenkopf vorübergehend zu

halten Gehäuse.

• Laço da corda sobre a cabeça do parafuso para reter

temporariamente habitação.

• Avvolgere il cordino sulla testa della vite per memorizzare

temporaneamente alloggi.

Make the appropriate wiring connections

from the dome to the pendant.

• Hacer las conexiones de cableado de la cúpula de la

pendiente.

• Faites le câblage de la coupole de la suspension.

• Nehmen Sie die entsprechenden Kabel-Verbindungen von der

Kuppel auf den Anhänger.

• Faça as conexões de cabos da cúpula para o pingente.

• Apportare le opportune connessioni cablaggio dalla cupola a

ciondolo.

Undo the lanyard, push housing up and twist. Secure

with the (2) locking bolts and washers. Add third

anti-twist screw if so equipped.

• Deshacer la cuerda de seguridad, empuje y gire hasta la vivienda. Asegure con los

tornillos de bloqueo (2) y las arandelas. Añadir tercero anti-torsión del tornillo si lo tiene.

• Défaire le cordon, appuyer sur le logement et torsion. Fixer avec les vis de blocage (2)

et les rondelles. Ajouter troisième anticorps anti-torsion vis si équipé.

• Lösen Sie die Leine, drücken Gehäuse und Touch. Sichern Sie mit den (2) Verriegelung

Schrauben und Unterlegscheiben. Fügen dritten anti-twist Schraube falls vorhanden.

• Desfazer o cordão, empurrar-se de habitação e torcer. Fixe com os parafusos (2) de

xação e arruelas. Adicionar parafuso anti-torção terceiro se assim equipado.

• Annulla il cordino, spingere abitazioni e torsione. Fissare con le (2) viti di bloccaggio

e le rondelle. Aggiungere un terzo anti-torsione vite se in dotazione.

•Third Anti-Twist

Screw

•Locking Screws

Slide the grommet down over the coupling to prevent

water from entering and complete the assembly.

• Resbale el ojal abajo sobre el acoplador para evitar que el agua

entre y para terminar a la asamblea.

• Glissez le canon isolant vers le bas au-dessus de l'accouplement

pour empêcher l'eau d'entrer et pour accomplir l'assemblée.

• Schieben Sie die Gummimuffe unten über der Koppelung, um zu

verhindern, daß Wasser und die Versammlung durchzuführen

hereinkommt.

• Deslize o ilhó para baixo sobre o acoplamento para impedir que a

água entre e para terminar o conjunto.

• Faccia scorrere il gommino di protezione giù sopra l'accoppiamento

per impedire l'acqua entrare e per completare il complessivo.

RJ45

24VAC

Camera

Heater/Blower

Yellow

Green

Yellow

Green

POWER

Max 80 Watts

26 Watts

1/0

Alarm 1

Alarm 2

Alarm 3

Common

Blue

Violet

Gray

White

Make the appropriate male and female connections. Indoor model does not include pre-run cables.

• Haga las conexiones masculinas y femeninas apropiadas. El modelo de interior no incluye pre-funciona los cables.

• Établissez les rapports masculins et femelles appropriés. Le modèle d'intérieur n'inclut pas pré-courent des câbles.

• Stellen Sie die passenden männlichen und weiblichen Beziehungen her. Innenmodell schließt nicht vor-laufen lassen Kabel

ein.

• Faça as conexões masculinas e fêmeas apropriadas. O modelo indoor não inclui pre-funciona cabos.

• Faccia i collegamenti maschii e femminili adatti. Il modello dell'interno non include pre-fa funzionare i cavi.

On board power supply provides 12VDC power

for camera

• A bordo fuente de alimentación proporciona la energía

12VDC para la cámara

• À bord de l'alimentation d'énergie fournit la puissance

12VDC pour l'appareil-photo

• An Bord des Spg.Versorgungsteils stellt Energie 12VDC für

Kamera zur Verfügung

• A bordo da fonte de alimentação fornece o poder 12VDC

para a câmera

• A bordo dell'alimentazione elettrica fornisce il potere 12VDC

per la macchina fotografica

Wire Gauge

Total vA

consumed

22 ,75

20 1,0

18 1,5

16 2,5

14 4

12 6

10 MM2

AWG

5.5 ft

400

121

600

182

960

292 ---

10 120

36.5

180

54.9

300

91.4

480

146

800

243

1300

396 -

20 86

27.1

141

43.0

225

68.6

358

109

571

174

905

275

1440

438

30 65

19.8

27.4

130

39.6

225

68.6

350

106

525

160

830

252

40 44

13.4

21.3

112

34.1

179

54.6

285

86.9

452

138

720

219

50 35

10.6

17.1

27.4

143

43.6

228

69.5

362

110

576

175

60 29

9.4

14.3

22.9

119

36.2

190

57.9

301

91.7

480

146

70 25

8.8

12.2

19.5

102

31.1

163

49.7

258

78.6

411

125

80 31

7.6

10.3

16.8

25.9

140

42.7

215

65.5

340

103

These are recommended maximum distances

for 24VAC with a 10% voltage drop.

• Éstos se recomiendan las distancias máximas para

24VAC con una caída de voltaje del 10%.

• Ceux-ci sont recommandés des distances maximum

pour 24VAC avec une chute de tension de 10%.

• Diese werden maximale Abstände für 24VAC mit

einem 10% Spannungsabfall empfohlen.

• Estes são recomendados distâncias máximas para

24VAC com uma queda de tensão de 10%.

• Questi sono suggeriti distanze massime per 24VAC con

una differenza de potenziale di 10%.

Hand tighten the screws on the dome.

Recommended torque 12 inches/lb (1.35Nm).

• La mano aprieta los tornillos en la bóveda. Esfuerzo de

torsión recomendado 12 inches/lb (el 1.35Nm).

• La main serrent les vis sur le dôme. Couple recom-

mandé 12 inches/lb (1.35Nm).

• Hand ziehen die Schrauben an der Haube fest.

Empfohlene Drehkraft 12 inches/lb (1.35Nm).

• A mão aperta os parafusos na abóbada. Torque

recomendado 12 inches/lb (1.35Nm).

• La mano stringe le viti sulla cupola. Coppia di torsione

suggerita 12 inches/lb (1.35Nm).

To install the dome align the tabs and twist

counter clockwise to secure.

• Para instalar la bóveda alinee las lengüetas y tuerza al revés

a la derecha para asegurar.

• Pour installer le dôme alignez les étiquettes et tordez contre

dans le sens des aiguilles d'une montre pour fixer.

• Um die Haube anzubringen richten Sie die Vorsprünge aus

und verdrehen Sie sich entgegengesetzt nach rechts um zu

sichern.

• Para instalar a abóbada alinhe as abas e torça-as contra no

sentido horário para fixar-se.

• Per installare la cupola allinei le linguette e torca contro in

senso orario per fissare.

Undo the lanyard, pull housing up and twist

secure with the locking bolt and washers.

• Deshaga el acollador, tire de contener para arriba y tuerza seguro

con el perno y las arandelas de fijación.

• Défaites la lanière, tirez loger vers le haut et tordez bloqué avec le

boulon et les rondelles de fermeture.

• Annulieren Sie die Abzuglinie, ziehen Sie oben unterbringen und

verdrehen Sie sicheres mit dem verriegelnschraubbolzen und den

Unterlegscheiben.

• Undo o colhedor, puxe abrigar acima e torça seguro com o

parafuso e as arruelas travando.

• Undo la cordicella, tiri l'alloggio in su e torca sicuro con il bullone e

le rondelle di bloccaggio.

Slide the grommet down over the coupling to prevent

water from entering and complete the assembly.

• Resbale el ojal abajo sobre el acoplador para evitar que el agua

entre y para terminar a la asamblea.

• Glissez le canon isolant vers le bas au-dessus de l'accouplement

pour empêcher l'eau d'entrer et pour accomplir l'assemblée.

• Schieben Sie die Gummimuffe unten über der Koppelung, um zu

verhindern, daß Wasser und die Versammlung durchzuführen

hereinkommt.

• Deslize o ilhó para baixo sobre o acoplamento para impedir que a

água entre e para terminar o conjunto.

• Faccia scorrere il gommino di protezione giù sopra l'accoppiamento

per impedire l'acqua entrare e per completare il complessivo.

1514

1312

When pressurizing unit be sure to set the

guage or regulator from 10-20psi (.7-1.4bar).

• Al presurizar la unidad sea seguro fijar la medida o el

regulador de 10-20psi (7-1.4bar).

• En pressurisant l'unité soyez sûr de placer la jauge ou le

régulateur de 10-20psi (7-1.4bar).

• Wenn Sie Maßeinheit unter Druck setzen, seien Sie sicher,

das Eichmaß oder den Regler von 10-20psi (7-1.4bar)

einzustellen.

• Ao pressurizar a unidade seja certo ajustar o guage ou o

regulador de 10-20psi (7-1.4bar).

• Nel pressurizzare l'unità sia sicuro regolare il misuratore o

il regolatore da 10-20psi (7-1.4bar).

PSI

100

150

200

250

300

Nitrogen

Tank

Hose

Regulator

Air Chuck

580

Fitting

Place the air chuck on the tank valve and

begin filling until pressure relief valve opens.

• Coloque la tirada del aire en la válvula del tanque y comience

a llenar hasta que la válvula de descarga de presión se abre.

• Placez le mandrin d'air sur la valve de réservoir et commencez

à remplir jusqu'à ce que la valve de décompression s'ouvre.

• Setzen Sie die Luftklemme auf das Behälterventil und fangen Sie

an zu füllen, bis Druckablaßventil sich öffnet.

• Coloque o mandril do ar na válvula do tanque e comece a

encher-se até que a válvula de escape de pressão abra.

• Disponga il mandrino dell'aria sulla valvola del carro armato e

cominci a riempirsi fino a che la valvola limitatrice della

pressione non si apra.

Air Chuck

Tank

Valve

Open the relief valve. Drain all air from the housing 3

times to remove all moisture.

• Abra la válvula de descarga. Drene todo el aire de la cubierta y

de la repetición 3 times dos veces para quitar toda la humedad.

• Ouvrez la soupape de sécurité. Évacuez tout l'air le logement et la

répétition 3 times pour enlever toute l'humidité.

• Öffnen Sie das Sicherheitsventil. Lassen Sie alle Luft aus dem

Gehäuse und der Wiederholung zweimal ab, um alle Feuchtigkeit

zu entfernen 3 times.

• Abra a válvula de escape. Drene todo o ar da carcaça e do

repeat 3 times para remover toda a umidade.

• Apra la valvola di sfiato. Vuoti due volte tutta l'aria 3 times

dall'alloggiamento e dalla ripetizione per rimuovere tutta l'umidità.

After purging check the housing pressure. It

should be around 5psi (.34bar).

• Después de purgar el cheque la presión de la cubierta.

Debe estar alrededor de 5psi (34bar).

• Après la purge du contrôle la pression de logement. Elle

devrait être autour de 5psi (34bar).

• Nachdem Überprüfung der Gehäusedruck bereinigt

worden ist. Sie sollte um 5psi (34bar) sein.

• Após ter removido a verificação a pressão da carcaça.

Deve ser em torno de 5psi (34bar).

• Dopo l'eliminazione dell'inceppo del controllo la pressione

dell'alloggiamento. Dovrebbe essere intorno a 5psi

(34bar).

PSI

18 19

PRESSURIZED HOUSING

Replacement Parts List

17 13

Part No. Description

1 RPPFD040 Housing Top

2 RPVL1938 Removable Pendent Coupling

3 RPVL1802 Plastic Rain Shroud

4 RPVL1795 Tank Valve Gasket

5 RP96RSORG11 Main O-Ring 9.25"

6 RPPFDTR01 Trim Ring w/o Dome

7 RCPFD7 Clear Dome with sealing O-Ring

7b RCTPFD7 Tinted Dome with sealing O-Ring

8 RPPFDT03 Internal Sealing Bracket Assembly

9 RP96RSORG10 Small O-Ring 4.5"

10 RP70PT07a Hermetic Connector, Gasket, Cable

11 RP95VALV08 5 to 7 psi Pressure Relief Valve

12 RP95VALV07 Tank Valve

13 RPFD072 24VAC Heater

14 RPVL1798a ½" Spacers (Set of 4)

15 RP40PCPPFD8 Connection PCB Assembly

16 RPFD060 Main Bracket Assembly

17 RPFD080 Blower

N/S RP40CAPPFD811 External Input Video/Power Cables

N/S RP46PKH2098 Packet Assembly-Hardware

N/S RP46PKH1100 Packet Assembly-Electrical

Moog FusionDome PFDW75T2N Installation And Operation Instructions Manual

Marca: Moog

Modelo: FusionDome PFDW75T2N

Categoría: Accesorios para cámaras de seguridad

Tipo: Installation And Operation Instructions Manual

Este manual también es adecuado para

PFDW75C2N

Descargar PDF

informe

Moog FusionDome PFDW75T2N Installation And Operation Instructions Manual

Este manual también es adecuado para

Moog FusionDome PFDW75T2N Installation And Operation Instructions Manual

En otros idiomas

Documentos relacionados

Otros documentos