Transcripción de documentos

UCA RX-V395 NATURAL SOUND AV RECEIVER AMPLI-TUNER AUDIO-VIDEO OWNER’S MANUAL MODE D’EMPLOI  SAFETY INSTRUCTIONS 8. Ventilation – The unit should be situated so that its location CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. ● Explanation of Graphical Symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. 1. Read Instructions – All the safety and operating instructions should be read before the unit is operated. 2. Retain Instructions – The safety and operating instructions should be retained for future reference. 3. Heed Warnings – All warnings on the unit and in the operating instructions should be adhered to. 4. Follow Instructions – All operating and other instructions should be followed. 5. Water and Moisture – The unit should not be used near water – for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc. 6. Carts and Stands – The unit should be used only with a cart or stand that is recommended by the manufacturer. 6A. A unit and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the unit and cart combination to overturn. 7. Wall or Ceiling Mounting – The unit should be mounted to a wall or ceiling only as recommended by the manufacturer. or position does not interfere with its proper ventilation. For example, the unit should not be situated on a bed, sofa, rug, or similar surface, that may block the ventilation openings; or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings. 9. Heat – The unit should be situated away from heat sources such as radiators, stoves, or other appliances that produce heat. 10. Power Sources – The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the unit. 11. Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the unit. 12. Cleaning – The unit should be cleaned only as recommended by the manufacturer. 13. Nonuse Periods – The power cord of the unit should be unplugged from the outlet when left unused for a long period of time. 14. Object and Liquid Entry – Care should be taken so that objects do not fall into and liquids are not spilled into the inside of the unit. 15. Damage Requiring Service – The unit should be serviced by qualified service personnel when: A. The power-supply cord or the plug has been damaged; or B. Objects have fallen, or liquid has been spilled into the unit; or C. The unit has been exposed to rain; or D. The unit does not appear to operate normally or exhibits a marked change in performance; or E. The unit has been dropped, or the cabinet damaged. 16. Servicing – The user should not attempt to service the unit beyond those means described in the operating instructions. All other servicing should be referred to qualified service personnel. 17. Power Lines – An outdoor antenna should be located away from power lines. 18. Grounding or Polarization – Precautions should be taken so that the grounding or polarization is not defeated.  Outdoor Antenna Grounding – If an outside antenna is connected to this unit, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. EXAMPLE OF ANTENNA GROUNDING MAST English 19. For US customers only: ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810–20) ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810–21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H) NEC – NATIONAL ELECTRICAL CODE FCC INFORMATION (for US customers only) 1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT : When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE : This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620. The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. We Want You Listening For A Lifetime YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels. 1  SUPPLIED ACCESSORIES ACCESSORIES FOURNIS ● ● ● ● After unpacking, check that the following parts are included. Après le déballage, vérifier que les pièces suivantes sont incluses. Indoor FM Antenna Antenne FM intérieure ● ● Remote Control Transmitter Emetteur de télécommande 6CH 2CH ● ● ● ● AM Loop Antenna Cadre-antenne AM Antenna adapter (U.S.A. and Canada models only) Adaptateur d’antenne (Modèles pour les États-Unis et le Canada seulement) ● ● 2 Batteries (size AAA, R03, UM-4) (4) Piles (taille AAA, R03, UM-4) (4)  English Thank you for selecting this YAMAHA AV receiver. FEATURES ● 5 Speaker Configuration (Power Amp. Section) ● 3 Center Channel Modes (NORMAL/WIDE/PHANTOM)V395RDS o Main: 60W + 60W (8Ω) RMS Output Power, 0.04% THD, 20–20,000 Hz Center: 60W (8Ω) RMS Output Power, 0.04% THD, 20–20,000 Hz Rear: 60W + 60W (8Ω) RMS Output Power, 0.04% THD, 20–20,000 Hz ● Digital Sound Field Processor ● Dolby Pro Logic Surround Decoder ● Theater-like Sound Experience by the Combination of Dolby Pro Logic and YAMAHA DSP Technology (CINEMA DSP) ● Automatic Input Balance Control for Dolby Pro Logic Surround ● Test Tone Generator for Easier Speaker Balance Adjustment ● 40-Station Random Access Preset Tuning ● Automatic Preset Tuning ● Preset Station Shifting Capability (Preset Editing) ● IF Count Direct PLL Synthesizer Tuning System ● 6-Channel External Decoder Input for Dolby Digital, DTS, and Other Future Formats ● Video Signal Input/Output Capability ● SLEEP Timer ● Universal Remote Control Transmitter with Preset Manufacturer Codes CONTENTS SUPPLIED ACCESSORIES ............................ 2 TUNING OPERATIONS ................................ 26 FEATURES ..................................................... 3 PRESET TUNING ......................................... 27 CAUTION ........................................................ 4 REMOTE CONTROL TRANSMITTER .......... 30 NOTES ABOUT THE REMOTE CONTROL TRANSMITTER ............................................... 5 USING DIGITAL SOUND FIELD PROCESSOR (DSP) .................................... 36 PROFILE OF THIS UNIT ................................ 6 SETTING THE SLEEP TIMER ...................... 40 SPEAKER SETUP .......................................... 7 SETUP CODES ............................................ 41 CONNECTIONS .............................................. 8 TROUBLESHOOTING .................................. 42 CONTROLS AND THEIR FUNCTIONS ........ 14 SPECIFICATIONS ........................................ 43 SPEAKER BALANCE ADJUSTMENT .......... 19 LIST OF MANUFACTURER’S CODES ......... 87 BASIC OPERATIONS ................................... 22 3  CAUTION : READ THIS BEFORE OPERATING YOUR UNIT. 1. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 2. Install this unit in a cool, dry, clean place – away from windows, heat sources, sources of excessive vibration, dust, moisture and cold. Avoid sources of humming (transformers, motors). To prevent fire or electrical shock, do not expose the unit to rain or water. 3. Never open the cabinet. If something drops into the set, contact your dealer. 4. Do not use force on switches, controls or connection wires. When moving the unit, first disconnect the power plug and the wires connected to other equipment. Never pull the wires themselves. 5. The openings on the unit cover assure proper ventilation of the unit. If these openings are obstructed, the temperature inside the unit will rise rapidly. Therefore, avoid placing objects against these openings, and install the unit in a well-ventilated area to prevent fire and damage. <China, U.K. and Europe models only> Be sure to allow a space of at least 20 cm behind, 20 cm on the both sides and 30 cm above the top panel of the unit to prevent fire and damage. 6. Always set the VOLUME control to “– ∞” before starting the audio source play. Increase the volume gradually to an appropriate level after playback has been started. IMPORTANT Please record the serial number of this unit in the space below. Model: Serial No.: The serial number is located on the rear of the unit. Retain this Owner’s Manual in a safe place for future reference. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power. FREQUENCY STEP switch <China and General models only> Because the interstation frequency spacing differs in different areas, set the FREQUENCY STEP switch (located on the rear panel) according to the frequency spacing in your area. Before setting this switch, disconnect the AC power plug of this unit from the AC outlet. 7. Do not attempt to clean the unit with chemical solvents; this might damage the finish. Use a clean, dry cloth. 8. Be sure to read the “TROUBLESHOOTING” section regarding common operating errors before concluding that the unit is faulty. 9. When not planning to use this unit for long periods of time (i.e., vacation, etc.), disconnect the AC power plug from the wall outlet. 10. To prevent lightning damage, disconnect the AC power plug and antenna cable when there is an electrical storm. 11. Grounding or polarization – Precautions should be taken so that the grounding or polarization of an appliance is not defeated. 12. Do not connect audio equipment to the AC outlet on the rear panel if the equipment requires more power than the outlet is rated to provide. 13. Voltage Selector <China and General models only> The voltage selector on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC power supply. Voltages are 110/120/220/240 V AC, 50/60 Hz. 4 For Canadian Customers To prevent electric shock, match wide blade of plug to wide slot and fully insert. This Class B digital apparatus complies with CANADIAN ICES-003  Special Instructions for U.K. Model If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described on the right. IMPORTANT THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: Note: The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live socket outlet. English For U.K. customers Blue: NEUTRAL Brown: LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Making sure that neither core is connected to the earth terminal of the three pin plug. NOTES ABOUT THE REMOTE CONTROL TRANSMITTER Battery installation Remote control transmitter operation range L 2 R Remote control sensor 1 3 Within approximately 6 m (19.7 feet) Battery replacement When you notice a decrease in the operating range of the remote control transmitter, the batteries are weak. Replace all batteries with new ones. Notes ● Use only AAA, R03, UM-4 batteries for replacement. ● Be sure the polarities are correct. (See the illustration inside the battery compartment.) ● Remove the batteries if the remote control transmitter will not be used for an extended period of time. ● If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries. ● When replacing batteries, try to install the new batteries within two minutes of removing the old batteries, or information stored in the remote control transmitter may be lost. Notes ● There should be no large obstacles between the remote control transmitter and the main unit. ● If the remote control sensor is directly illuminated by strong lighting (especially an inverter type of fluorescent lamp, etc.), it might cause the remote control transmitter not to work correctly. In this case, reposition the main unit to avoid direct lighting. 5  PROFILE OF THIS UNIT You are the proud owner of a Yamaha stereo receiver – an extremely sophisticated audio component. The Digital Sound Field Processor (DSP) built into this unit takes advantage of Yamaha’s undisputed leadership in the field of digital audio processing to bring you a whole new world of listening experiences. Follow the instructions in this manual carefully when setting up your system, and this unit will sonically transform your room into a wide range of listening environments – movie theater, concert hall, and so on. In addition, you get incredible realism from sources encoded with Dolby Surround using the built-in Dolby Pro Logic Surround decoder. Please read this owner’s manual carefully and store it in a safe place for later reference. Digital Sound Field Processing What is it that makes live music so good? Today’s advanced sound reproduction technology lets you get extremely close to the sound of a live performance, but chances are you’ll still notice something missing: the acoustic environment of the live concert hall. Extensive research into the exact nature of the sonic reflections that create the ambience of a large hall has made it possible for Yamaha engineers to bring you this same sound in your own listening room, so you’ll feel all the sound of a live concert. Furthermore, our technicians, armed with sophisticated measuring equipment, have even made it possible to capture the acoustics of a variety of venues such as an actual concert hall, theater, etc. to allow you to accurately recreate one of several actual live performance environments, all in your own home. Dolby Pro Logic Surround This unit employs a Dolby Pro Logic Surround decoder similar to professional Dolby Stereo decoders used in many movie theaters. By using the Dolby Pro Logic Surround decoder, you can experience the dramatic realism and impact of Dolby Surround movie theater sound in your own home. Dolby Pro Logic employs a four channel five speaker system. The Pro Logic Surround system divides the input signal into four levels: the left and right main channels, the center channel (used for dialog), and the rear surround sound channel (used for sound effects, background noise, and other ambient noises). The center channel allows listeners seated in even less-than-ideal positions to hear the dialog originating from the action on the screen while experiencing good stereo imaging. Dolby Surround is encoded on the sound track of pre-recorded video tapes, laser discs, and some TV/cable broadcasts. When you play a source encoded with Dolby Surround on this unit, the Dolby Pro Logic Surround decoder decodes the signal and distributes the surround-sound effects. This Dolby Pro Logic Surround Decoder employs a digital signal processing system. This system improves the stability of sound at each channel and minimizes crosstalk between channels, so that positioning of sounds around the room is more accurate compared with conventional analog signal processing systems. In addition, this unit features a built-in automatic input balance control. This always assures you the best performance without manual adjustment. Manufactured under license from Dolby Laboratories. “Dolby”, “AC-3”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. Dolby Pro Logic Surround + DSP A Dolby Surround sound system shows its full ability in a large movie theater, because movie sounds are originally designed to be reproduced in a large movie theater using many speakers. It is difficult to create a sound environment similar to that of a movie theater in your listening room, because the room size, materials of inside walls, the number of speakers, etc. of your listening room is much different from those of a movie theater. Yamaha DSP technology made it possible to present you with nearly the same sound experience as that of a large movie theater in your listening room by compensating for lack of presence and dynamics in your listening room with its original digital sound fields combined with Dolby Surround sound field. 6 The combination of Dolby Pro Logic Surround and DSP is used on the sound field program “ PRO LOGIC ENHANCED”. CINEMA DSP The YAMAHA “CINEMA DSP” logo indicates these programs are created by the combination of Dolby Pro Logic and YAMAHA DSP technology.  English SPEAKER SETUP SPEAKERS TO BE USED This unit is designed to provide the best sound-field quality with a 5 speaker configuration. The most effective speakers to use with this unit are main speakers, rear speakers and a center speaker. You may omit the center speaker. (Refer to the “4-Speaker Configuration” shown below.) The main speakers are used for the majority of the sound output as well as effect sounds. The rear speakers are used for the effect and surround sounds, and the center speaker is for the center sounds (dialog, etc.) within programs encoded with Dolby Surround. The center speaker needs to be equal in power to the main speakers, though the rear speakers should be slightly lower in power. However, all the speakers should have high enough power handling to accept the maximum output of this unit. SPEAKER CONFIGURATION 5-Speaker Configuration 4-Speaker Configuration This configuration is the most effective and recommended one. In this configuration, the center speaker is necessary as well as the rear speakers. If the program DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED is selected, conversations will be output from the center speaker and the ambience will be excellent. ● Set the center channel mode to the “NORMAL” or “WIDE” position. (For details, refer to page 20.) The center speaker is not used in this configuration. If the program DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED is selected, the center sound is output from the left and the right main speakers. However, the sound effect of other programs can be the same as that of the 5-speaker configuration. ● Be sure to set the center channel mode to the “PHANTOM” position. (For details, refer to page 20.) Main L Main R Center Main L Main R Dialogue Dialogue Surround sound Surround sound Rear L Rear L Rear R Rear R SPEAKER PLACEMENT The recommended 5-speaker configuration requires a pair of main speakers, a center speaker, and a pair of rear speakers (sometimes referred to as surround speakers). When arranging your speakers, refer to the illustration and information below. Main: Main R Center Main L TV set Rear R Position the main speakers at equal distances away from the listening position and at equal distances on either side of the center speaker. Rear: Position rear speakers directly behind the listening position at a height of approximately 1.8m (6 feet) up from the floor, facing slightly inward. If the speakers cannot be placed behind the listening position, they may also be placed at the side of the listening position, facing toward the listening position. Center: Position the center speaker directly in front of the listening position between the main speakers. (When placing on or near a television, use a magnetically shielded speaker to avoid unwanted interference.) Rear L 7  CONNECTIONS CONNECTIONS WITH OTHER COMPONENTS Never plug in this unit and other components until all connections are completed. When making connections between this unit and other components, be sure all connections are made correctly; that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit. * If you have YAMAHA components numbered as 1, 3, 4, etc. on the rear panel, connections can be made easily by connecting the output (or input) terminals of each component to the same-numbered terminals on this unit. *1 AUDIO IN VIDEO IN AUDIO OUT VIDEO OUT VIDEO OUT Video cassette recorder VIDEO IN GND OUTPUT TV/Satellite tuner AUDIO OUT Monitor TV Turntable *2 6CH DISCRETE INPUT MAIN CENTER VOLTAGE SELECTOR <General model> SURROUND 75ΩUNBAL. L FM ANT A L R *3 R SUB WOOFER IMPEDANCE SELECTOR B VIDEO SIGNAL GND GND MONITOR OUT DVD/LD TV/DBS IN VCR OUT CENTER REAR AM ANT AC OUTLETS SET BEFORE POWER ON MAIN A OR B: 4ΩMIN. /SPEAKER A B: 8ΩMIN. /SPEAKER : 6ΩMIN. /SPEAKER : 6ΩMIN. /SPEAKER REAR R (SURROUND) CENTER REAR AUDIO SIGNAL PHONO CD TAPE/MD IN OUT (PLAY) (REC) 3 4 DVD/LD TV/DBS MAIN A OR B: 8ΩMIN. /SPEAKER A B:16ΩMIN. /SPEAKER IN VCR : 8ΩMIN. /SPEAKER : 8ΩMIN. /SPEAKER OUT 50kHz / 9kHz 100kHz /10kHz FM / AM Tape deck, MD recorder, etc. *1 Ground (GND) terminal (For turntable use) Connecting the ground wire of the turntable to the GND terminal will normally minimize hum, but in some cases better results may be obtained with the ground wire disconnected. *2 Voltage Selector <China and General models only> The voltage selector on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC power supply. Voltages are 110/120/220/240 V AC, 50/60 Hz. 8 AUDIO OUT VIDEO OUT LINE IN OUTPUT CD player I00W MAX. TOTAL SWITCHED LINE OUT 1 FREQUENCY STEP To AC outlet LD player, DVD player, etc. *3 AC OUTLETS (SWITCHED) <Europe, Canada, U.S.A., China and General models> ..................................................... 2 SWITCHED OUTLETS <U.K. and Australia models> .......... 1 SWITCHED OUTLET Use these to connect the power cords from your components to this unit. The power to the SWITCHED AC OUTLETS is controlled by this unit’s STANDBY/ON switch or the provided remote control transmitter’s POWER /I key. These outlets will supply power to any component whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to the SWITCHED AC OUTLETS is 100 watts.  English Connecting an external decoder for Dolby Digital, DTS and other future formats or a DVD player, etc. If you have a separate Dolby Digital, DTS or other format decoder, or if you have a DVD player or other component which incorporates a Dolby Digital, DTS, or other format decoder, its 6 channel discrete outputs can be connected to the 6CH DISCRETE INPUT terminals of this unit. (Example) 6CH DISCRETE OUTPUT MAIN CENTER SURROUND Dolby Digital decoder DIGITAL IN SUB WOOFER 6CH DISCRETE INPUT MAIN CENTER SURROUND DIGITAL OUT 75ΩUNBAL. L L R FM ANT R SUB WOOFER GND VIDEO SIGNAL GND MONITOR OUT DVD/LD TV/DBS IN RF Demodulator VCR OUT AM ANT AUDIO SIGNAL PHONO CD TAPE/MD IN OUT (PLAY) (REC) 3 4 DVD/LD TV/DBS IN VCR DOLBY DIGITAL RF (AC-3 RF) IN OUT 50kHz / 9kHz 100kHz /10kHz FM / AM FREQUENCY STEP 1 DOLBY DIGITAL RF (AC-3 RF) OUT VIDEO OUT <General model> AUDIO OUT Laserdisc player or other unit with Dolby Digital RF (AC-3 RF) output Notes ● The laserdisc player (or other unit) must be also connected to the DVD/LD (or TV/DBS) AUDIO SIGNAL input terminals of this unit to play a source encoded with Dolby Pro Logic Surround or in normal stereo (or monaural). ● The discrete signals input to this unit cannot be recorded by a tape deck, MD recorder or VCR. To record a source played on the laserdisc player (or another unit), it must be connected to the DVD/LD (or TV/DBS) AUDIO/VIDEO SIGNAL input terminals of this unit. ● If you made no connection to the SUB WOOFER input terminal of this unit or you will not use a subwoofer, you should be able to make a setting on the decoder to distribute SUB WOOFER channel signals to the right and left MAIN output terminals. For details, refer to the owner’s manual supplied with the decoder. 9  CONNECTING SPEAKERS Main speakers A Right Main speakers B Left Left Right <General model> SPEAKERS MAIN A IMPEDANCE SELECTOR B Subwoofer system SET BEFORE POWER ON MAIN A OR B: 4ΩMIN. /SPEAKER A B: 8ΩMIN. /SPEAKER CENTER REAR REAR CENTER R (SURROUND) OUTPUT : 6ΩMIN. /SPEAKER : 6ΩMIN. /SPEAKER MAIN A OR B: 8ΩMIN. /SPEAKER A B:16ΩMIN. /SPEAKER CENTER REAR : 8ΩMIN. /SPEAKER : 8ΩMIN. /SPEAKER SUB WOOFER CAUTION SEE INSTRUCTION MANUAL FOR CORRECT SETTING. Right Center speaker Note Use speakers with the specified impedance shown on the rear of this unit. Note on main speaker connections: One or two speaker systems can be connected to this unit. If you use only one speaker system, connect it to either the SPEAKERS A or B terminals. Note on subwoofer connection: You may wish to add a subwoofer to reinforce low frequencies or to output low bass sound from the subwoofer channel when reproducing discrete signals. Connect the SUBWOOFER OUTPUT terminal of this unit to the input terminal of the subwoofer amplifier, and connect the speaker terminals of the subwoofer amplifier to the subwoofer. With some subwoofers, including the Yamaha Active Servo Processing Subwoofer System, the amplifier and subwoofer are in the same unit. 10 Left Rear speakers  Connect the SPEAKERS terminals to your speakers with wire of the proper gauge, cut as short as possible. If the connections are faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is the + and – markings are observed. If these wires are reversed, the sound will be unnatural and lack bass. English How to Connect: Caution Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or speakers. To connect to the MAIN SPEAKERS terminals Red: positive (+) Black: negative (–) 2 1 3 <U.S.A., Canada, Australia, China and General models only> Banana Plug connections are also possible. Simply insert the Banana Plug connector into the corresponding terminal. 1 Unscrew the knob. 2 Insert the bare wire. 3 [Remove approx. 5mm (1/4”) insulation from the speaker wires.] Tighten the knob and secure the wire. To connect to the REAR and CENTER SPEAKERS terminals Red: positive (+) Black: negative (–) 1 Press the tab. 2 Insert the bare wire. 1 3 3 2 [Remove approx. 5mm (1/4”) insulation from the speaker wires.] Release the tab and secure the wire. 11  SUBWOOFER OUTPUT terminal OUTPUT SUB WOOFER This terminal is for connecting to the input terminal of an amplifier driving a subwoofer. This terminal outputs low frequencies from the main and center channels. (The cut-off frequency of signals output from this terminal is 150 Hz.) When 6 channel discrete signals are input to this unit and are selected as the input source, this terminal outputs signals from the subwoofer channel. IMPEDANCE SELECTOR switch Be sure to switch this only when the power to this unit is not on. Select the position whose requirements your speaker system meets. WARNING Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise this unit may be damaged. IF THIS UNIT FAILS TO TURN ON WHEN THE STANDBY/ ON SWITCH IS PRESSED, the IMPEDANCE SELECTOR switch may not be set to either end closely. If so, set the switch to either end closely. (Left position) Main: If you use one pair of main speakers, the impedance of each speaker must be 4Ω or higher. If you use two pairs of main speakers, the impedance of each speaker must be 8Ω or higher. Center: The impedance of the speaker must be 6Ω or higher. Rear: The impedance of each speaker must be 6Ω or higher. (Right position) Main: <General model> VOLTAGE SELECTOR <Except for Canada model> If you use one pair of main speakers, the impedance of each speaker must be 8Ω or higher. If you use two pairs of main speakers, the impedance of each speaker must be 16Ω or higher. <Canada model only> The impedance of each speaker must be 8Ω or higher. Center: The impedance of the speaker must be 8Ω or higher. IMPEDANCE SELECTOR AC OUTLETS Rear: SET BEFORE POWER ON MAIN A OR B: 4ΩMIN. /SPEAKER A B: 8ΩMIN. /SPEAKER CENTER REAR : 6ΩMIN. /SPEAKER : 6ΩMIN. /SPEAKER MAIN A OR B: 8ΩMIN. /SPEAKER A B:16ΩMIN. /SPEAKER CENTER REAR : 8ΩMIN. /SPEAKER : 8ΩMIN. /SPEAKER I00W MAX. TOTAL SWITCHED IMPEDANCE SELECTOR 12 The impedance of each speaker must be 8Ω or higher.  ● ● Each antenna should be connected to the designated terminals correctly, referring to the following diagram. Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may result in improvement. Outdoor FM antenna English ANTENNA CONNECTIONS Outdoor AM antenna Indoor FM antenna (included) AM loop antenna (included) 75-ohm/300-ohm antenna adapter 75Ω UNBAL. FM ANT 75-ohm coaxial cable GND AM ANT 75-ohm/300-ohm antenna adapter 300-ohm feeder Ground Connecting the AM loop antenna 1 2 3 Orient so that the best reception is obtained. * The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall. * The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit. GND terminal For maximum safety and minimum interference, connect the GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth. Notes ● When connecting the indoor FM antenna, insert its connector into the FM ANT terminal firmly. ● If you need an outdoor FM antenna to improve FM reception quality, either 300-ohm feeder or coaxial cable may be used. In locations troubled by electrical interference, coaxial cable is preferable. 13  CONTROLS AND THEIR FUNCTIONS FRONT PANEL Ÿ ~ ! ⁄ @ ¤ # $ ‹ NATURAL SOUND AV RECEIVER VOLUME l6 20 VCR TV/DBS DVD/LD 2CH/6CH 2CH/6CH STANDBY/ON l2 28 8 60 2 4 40 TAPE/MD MONITOR CD PHONO TUNER 0 –dB A/B/C/D/E 2 1 4 3 5 6 7 8 MEMORY MAN'L/AUTO FM PHONES BASS 0 l l SPEAKERS A B 2 2 3 ON fi ^ 3 4 5 BALANCE 0 l l 2 3 4 5 › % 2 3 4 OFF TREBLE 0 l l 4 5 5 fl 2 TUNING MODE FM/AM DOWN DELAY/CENTER/ REAR/SWFR TIME/LEVEL ENHANCED CONCERT VIDEO MONO MOVIE CENTER MODE DISCO ROCK CONCERT TUNING UP AUTO/MAN'L MONO PRO LOGIC 2 3 3 4 TV SPORTS CONCERT HALL EFFECT 4 L5 5R & ~ STANDBY/ON switch Press this switch to turn the power to this unit on. Press it again to put this unit in the standby mode. In STANDBY, this unit consumes a very small quantity of power to receive infrared signals from the remote control transmitter. Ÿ Remote control sensor Receives signals from the remote control transmitter. ! Display panel Shows various information. (Refer to page 18.) ⁄ MEMORY (MAN’L/AUTO FM) button Press this button to preset AM and FM radio frequencies manually. (Refer to page 27.) When this button is pressed and held for more than 3 seconds, automatic preset tuning begins. (Refer to page 28.) @ EDIT button This button is used to exchange the places of two preset stations with each other. (Refer to page 29.) 14 EDIT ‡ * ° ( · ¤ TUNING MODE (AUTO/MAN’L MONO) button Press this button to switch the tuning mode to automatic or manual. To select the automatic tuning mode, press this button so that the AUTO indicator lights up on the display. To select the manual tuning mode, press this button so that the AUTO indicator goes off. (Refer to page 26.) # FM/AM button Press this button to switch the reception band to FM or AM. (Refer to page 26.) ‹ Input selector buttons Select a program source to listen to or watch. When a button is pressed, the name of selected source appears on the display. When either the TV/DBS or DVD/LD input source is selected, pressing the same selector button repeatedly switches the input signals between 2 channel stereo signals and 6 channel discrete signals. When switched to “6ch”, discrete signals from the unit connected to the 6CH DISCRETE INPUT terminals of this unit are selected as the input signals. $ VOLUME control Use to raise or lower the volume level.  & BALANCE control To listen with headphones, connect the headphones to the PHONES jack. The sound output from the PHONES jack is the same as that from the main speakers. When listening with headphones privately, set both the SPEAKERS A and B switches to the OFF position and switch off the digital sound field processor (so that no DSP program indicator is lit in the display) by pressing the EFFECT button. This control is effective only for the sound from the main speakers. Adjusts the balance of the output volume to the left and right speakers to compensate for sound imbalance caused by speaker location or listening room conditions. (Refer to page 25.) PHONES English › PHONES jack ‡ TUNING DOWN/UP button Use for tuning radio stations. Press the UP side to tune in to higher frequencies, and press the DOWN side to tune in to lower frequencies. * DSP program selector buttons Select a DSP program. When a button is pressed, the name of selected program lights up on the display. (Refer to page 36.) % SPEAKERS switches Set the switch A or B (or both A and B) for the main speaker system (connected to this unit) you will use to the ON position. Set the switch for the main speaker system you will not use to the OFF position. (Refer to page 25.) fi A/B/C/D/E button Press this button to select a desired group (A–E) of preset stations. (Refer to page 27.) ^ Preset station number selector buttons Press to select a preset station number (1 to 8). (Refer to page 27.) fl Tone controls These controls are effective only for the sound from the main speakers. (Refer to page 25.) BASS Used to increase or decrease the low frequency response. The 0 position produces flat response. TREBLE Used to increase or decrease the high frequency response. The 0 position produces flat response. ° EFFECT button Switches the digital sound field processor on and off (including the Dolby Pro Logic Surround decoder). (Refer to page 37.) ( CENTER MODE button Selects a center channel output mode (NORMAL, WIDE or PHANTOM). (Refer to page 20.) · DELAY/CENTER/REAR/SWFR and TIME/LEVEL +/– buttons Adjust the delay time (DELAY), the center channel output level (CENTER), the rear channel output level (REAR) and the output level to the SUBWOOFER OUTPUT terminal (SWFR). Select the item which you want to adjust by pressing the DELAY/CENTER/REAR/SWFR button and adjust its time or level by pressing the TIME/LEVEL +/– button. (Refer to pages 25, 38, and 39.) 15  REMOTE CONTROL TRANSMITTER The remote control transmitter provided with this unit is designed to control all the most commonly used functions of this unit as well as the components connected to it. The remote control transmitter is factory set to control this unit and most Yamaha components. To set up the remote control transmitter to control the components of other manufacturers, refer to “SETUP CODES” on page 41. 6CH 2CH 16  Press the button for the component you want to control with the remote control transmitter. (The proper code must be set for your component. See “SETUP CODES” on page 41.) When the component selector has been pressed, the remote control transmitter is set to operate that component. Ÿ POWER /I When you have preset the code for a YAMAHA component, this button switches between the power on and standby mode. When you have preset the code for another manufacturer’s component, this button turns on that component if it has a remote control transmitter with a power button. * Functions only when the component selector button AMP<TUNER>, TAPE/MD, CD, DVD/LD or DVD MENU has been pressed. ! TEST Press this button to output the test tone for each speaker. * Functions only when the component selector button AMP<TUNER> has been pressed. ⁄ MUTE Press this button to mute the sound. @ VOLUME These buttons are used to adjust the volume. : Turns up the volume. : Turns down the volume. ¤ SLEEP This button is used to set the SLEEP timer. # PRG+, PRG– These buttons are used to select a DSP program. * Function only when the component selector button AMP<TUNER> has been pressed. ‹ Indicator This flashes in red when a button on the remote control transmitter is pressed. When it flashes rapidly several times, press the selected button again. $ Input selector (1 to 7) › EFFECT 1) / CLEAR2)/ +1003) 1) This button is used to switch the DSP program on or off. * Functions only when AMP<TUNER>, TAPE/MD, CD, DVD/LD, VCR or TV on the component selector has been pressed. 2) This button is used to clear the settings. * Functions only when the component selector button DVD MENU has been pressed. 3) This button is used to select the channel. * Functions only when the component selector button CBL/ DBS has been pressed. English ~ Component selector % ENTER 1) / +102)/ A/B/C/D/E3) 1) This button is used to enter the channel. * Functions only when the component selector button VCR, CBL/DBS or TV has been pressed. 2) This button is used to select the menu. * Functions only when the component selector button DVD MENU has been pressed. 3) This button is used to select a group of presets. * Functions only when the component selector button AMP <TUNER> has been pressed. fi DISC SKIP +/– 1) / CH +/–2) / PRESET +/–3) 1) These buttons are used to skip to the next or previous disc. * Function only when the component selector button CD, DVD/LD or DVD MENU has been pressed. 2) These buttons are used to select the next or previous channel. * Function only when the component selector button VCR, CBL/DBS or TV has been pressed. 3) These buttons are used to select a preset station. * Functions only when the component selector button AMP <TUNER> has been pressed. ^ Operation buttons 1) / Setup buttons2) 1) These buttons function as play, stop, skip, etc. for operating the component. * Function only when the component selector button TAPE/ MD, CD, DVD/LD, VCR or TV has been pressed. 2) These buttons are for adjusting various settings. * Function only when the component selector button DVD MENU or CBL/DBS has been pressed. 1) / Numeric buttons2) 1) These buttons are used to select the program source to be played. * Function only when the component selector button AMP<TUNER>, TAPE/MD, CD or DVD/LD has been pressed. 2) These buttons are used to select the menu or channel. * Function only when the component selector button DVD MENU, VCR, CBL/DBS or TV has been pressed. 17  DISPLAY PANEL Ÿ ! ⁄ ~ PRESET @ ¤ SLEEP ms dB STEREO NORM WIDE PHANTOM l00 0 20 EFFECT OFF PRO LOGIC CONCERT MONO DISCO ROCK CONCERT ENHANCED VIDEO MOVIE TV SPORTS CONCERT HALL kHz MHz MEMORY AUTO # TAPE MON ‹ $ ~ Multi-information display Displays various information, for example station frequency, preset station number and name of selected input source. Ÿ STEREO indicator Lights up when an FM stereo broadcast with sufficient signal strength is received. # MEMORY indicator When the MEMORY button is pressed, this indicator flashes for about 5 seconds. During this period, the displayed station can be programmed to the memory by using the A/B/C/D/E button and the preset station number selector buttons. ‹ AUTO indicator ! Signal-level meter Lights up when this unit is in the automatic tuning mode. Indicates the signal level of the received station. If multipath interference is detected, the indication decreases. $ TAPE MON indicator ⁄ SLEEP indicator Lights up while the built-in SLEEP timer is functioning. @ Center channel mode indicators The name of a selected center channel mode lights up only when a program which uses Dolby Pro Logic Surround is selected. ¤ EFFECT OFF indicator Lights up if neither the digital sound field processor nor the Dolby Pro Logic Surround decoder is on. In this state, sound output is 2-channel stereo. 18 › Lights up when the tape deck (or MD recorder, etc.) is selected as the input source by pressing the TAPE/MD MONITOR button. › DSP program indicators The name of a selected DSP program lights up when the builtin digital sound field processor or the Dolby Pro Logic Surround decoder is on.  This procedure lets you adjust the sound output level balance between the main, center, and rear speakers using the built-in test tone generator. When this adjustment is performed, the level heard at the listening position should sound the same from each speaker. This is important for the best performance of the digital sound field processor and the Dolby Pro Logic Surround decoder. 2 English SPEAKER BALANCE ADJUSTMENT 1 2 L R 6CH 2CH 3 4 5 Press the component selector button AMP<TUNER> on the remote control transmitter. 3 Select the main speakers to be used. SPEAKERS A B ON OFF * If you use two main speaker systems, press both the A and B switches. 1 4 VOLUME l6 20 l2 28 BASS 0 l 2 2 3 44 40 TREBLE 0 l l l 8 3 4 4 5 5 2 BALANCE 0 l l 2 3 3 4 4 5 5 2 2 3 3 4 4 L5 5R 2 60 0 Set BASS, TREBLE and BALANCE to the “0” position. –dB Set VOLUME to the minimum level (– ∞ dB). 2 5 Press the TEST button so that “TEST LEFT” appears in the display. Turn the power on. STANDBY/ON 19  10 7 9 L R 8 6 9 67 Select the center channel output mode suitable for your speaker configuration. (Refer to “SPEAKER CONFIGURATION” on page 7.) 7 Turn up the volume. VOLUME l6 20 l2 28 8 44 40 CENTER MODE NORMAL 2 60 WIDE PHANTOM On the feature of each mode, refer to the “Note” shown below. 0 –dB You will hear a test tone (like pink noise) in order from the left main speaker, the center speaker, the right main speaker, and then the rear speakers for about two seconds each. The display changes as shown below. Main (L) Center Note In step 6, when you select a center channel output mode, note the following. For 5 speaker configuration NORMAL: Select this mode when you use a center speaker that is smaller than the main speakers. In this mode, the bass tone will be output from the main speakers. WIDE: Select this mode when you use a center speaker approximately the same size as the main speakers. For 4 speaker configuration PHANTOM: Select this mode when you do not use the center speaker. The center speaker sound will be output from the left and right main speakers. Rear (L and R) Main (R) * The test tone from the left rear speaker and the right rear speaker will be heard at the same time. 8 Adjust the BALANCE control so that the sound output level of the left main speaker and the right main speaker are the same. BALANCE 0 l l 2 2 3 3 4 4 L5 20 5R  Adjust the sound output levels of the center speaker and the rear speakers so that they sound as similar as possible to the level of the main speakers. English 9 Make the adjustment of each speaker output level at your listening position with the remote control transmitter. a) b) Press the TIME/LEVEL button once or more so that “CENTER” or “REAR” appears on the display. * Select “CENTER” to adjust the output level of the center speaker, and select “REAR” to adjust the output level of the rear speakers. Press the + and – operation buttons to adjust the level. 10 Press the TEST button again to cancel the test tone. Notes Once you have completed these adjustments, you can adjust the overall sound level of your audio system by using the VOLUME control (or the VOLUME keys on the remote control transmitter) only. ● If you use external power amplifiers, you may also use their volume controls to achieve proper balance. ● In step 9, if the center channel mode is in the “PHANTOM” position, the sound output level of the center speaker cannot be adjusted, because the center sound is automatically output from the left and right main speakers. ● 21  This manual describes how to operate this unit mainly by using the front panel control parts. To operate this unit on the remote control transmitter, use the corresponding keys on the remote control transmitter. BASIC OPERATIONS TO PLAY A SOURCE 2 3 L 4 1 R 7 5 VOLUME l6 20 l2 28 1, 6 Play the source. (For detailed information on tuning operations, refer to page 26.) 8 6 44 40 VOLUME l6 2 60 20 0 l2 28 8 –dB 44 40 Set VOLUME to the minimum level (– ∞ dB). 2 60 0 2 –dB Turn the power on. Adjust to the desired output level. STANDBY/ON 7 3 Select the desired input source by using the input selector buttons. (For video sources, turn the TV/monitor ON.) TUNER CD PHONO TAPE/MD MONITOR * The name of the selected input source will appear on the display. 4 Select the main speakers to be used. SPEAKERS A ON B OFF If desired, adjust BASS, TREBLE and BALANCE (refer to page 25), and/or use the digital sound field processor. (Refer to page 37.) Notes on using the input selector buttons Note that pressing each input selector button selects the source which is connected to the corresponding input terminals on the rear panel. ● The selection of TAPE/MD MONITOR cannot be canceled by pressing another input selector button. To cancel it, press TAPE/MD MONITOR again so that the TAPE MON indicator disappears from the display. When you select a button other than TAPE/MD MONITOR, make sure that the TAPE MON indicator is not illuminated on the display. ● If you select the input selector button for a video source without canceling the selection of TAPE/MD MONITOR, the playback result will be the video image from the video source and the sound from the audio tape (or MD, etc.). ● Once you play a video source, its video image will not be interrupted even if the input selector button for an audio source is selected. ● When you finish using this unit * If you use two main speaker systems, press both the A and B switches. 22 Press the STANDBY/ON switch on the front panel again or the POWER /I key on the remote control transmitter to put this unit in the standby mode.  In step 3 on page 22, press either the DVD/LD or TV/DBS button once or more so that “6ch” appears in the display. Discrete signals from the component connected to the 6CH DISCRETE INPUT terminals of this unit are selected as the input signals. TV/DBS DVD/LD 2CH/6CH 2CH/6CH VCR To stop listening to a decoded source with Dolby Digital, DTS, or other future format Press the DVD/LD or TV/DBS button again to switch the input from six channel input to two channel input or select another input source. When two channel input is selected, the 6CH DISCRETE INPUT terminals are not used. TV/DBS DVD 2CH/6CH 2CH/ or PHONO CD TAPE/MD MONITOR UNER PHONO CD English To listen to a source with Dolby Digital, DTS or other future format by reproducing the decoded signals input at the 6CH DISCRETE INPUT terminals of this unit. TA MO Notes on reproducing discrete signals with Dolby Digital, DTS, or other future format: 1. Your speaker system must include a center speaker. 2. Your speaker system should include a subwoofer. * Connect a subwoofer which has a built-in amplifier directly to the SUBWOOFER OUTPUT terminal of this unit. For more details on hooking up a subwoofer to this unit, refer to pages 10 and 12. * If you do not have a subwoofer in your system, it may be possible to make a setting on the Dolby Digital, DTS, or other future format decoder to distribute LFE channel signals to the right and left MAIN output terminals. For details, refer to the owner’s manual supplied with your decoder. Notes ● When you switch to the “6ch” mode, the built-in digital sound field processor (DSP) will not work and adjustments to delay time settings cannot be made. ● Switching this unit to the “6ch” mode will input no signal to this unit if there is no connection made to the 6CH DISCRETE INPUT terminals of this unit. 23  TO RECORD A SOURCE TO TAPE OR MD 1 L 1 2 R 3 Select the source to be recorded. 4 TAPE/MD MONITOR CD PHONO TUNER 4 2 Play the source and then turn the VOLUME control up to confirm the input source. (For detailed information on tuning operations, refer to the page 26.) Begin recording on the tape deck (or MD recorder, etc.) or VCR connected to this unit. If the tape deck (or MD recorder, etc.) is used for recording, you can monitor the sounds being recorded by pressing TAPE/MD MONITOR so that the “TAPE MON” indicator lights up on the display. TV/DBS DVD/LD 2CH/6CH 2CH/6CH PHONO CD TAPE/MD MONITOR VOLUME l6 20 l2 28 8 44 40 2 60 0 –dB 24 Notes The settings of DSP and the VOLUME, BASS, TREBLE and BALANCE controls have no effect on the material being recorded. ● In step 1, do not make an input source selection so that “6ch” appears on the display. Signals input to this unit’s 6CH DISCRETE INPUT terminals cannot be recorded by a tape deck, MD recorder or VCR. ●  Because one or two speaker systems (as main speakers) can be connected to this unit, the SPEAKERS switches allow you English to select speaker system A or B, or both at once. Adjusting the BASS and TREBLE controls BASS 0 l TREBLE 0 l l l SPEAKERS A 2 2 3 B 3 4 4 5 ON 5 English Selecting the SPEAKER system 2 2 3 3 4 4 5 5 OFF BASS Adjusting the BALANCE control Adjust the balance of the output volume to the left and right speakers to compensate for sound imbalance caused by speaker location or listening room conditions. : Turn this clockwise to increase (or counterclockwise to decrease) the low frequency response. TREBLE : Turn this clockwise to increase (or counterclockwise to decrease) the high frequency response. Note These controls are effective only for the sound from the main speakers. BALANCE 0 l l 2 2 3 3 4 4 L5 5R Note This control is effective only for the sound from the main speakers. Adjusting the subwoofer output level If your audio system includes a subwoofer, and an amplifier driving the subwoofer (or a subwoofer system including an amplifier) is connected to the SUBWOOFER OUTPUT terminal on the rear of this unit, you can adjust the subwoofer output level on this unit. 1 Press once or more so that “SWFR” appears on the display. DELAY/CENTER/ REAR/SWFR 2 By continuously pressing the “+” or “–” side of the TIME/ LEVEL button, the level value changes continuously. If you feel that bass tone is insufficient, increase the level, and if you feel that bass tone is overly emphasized, decrease the level. TIME/LEVEL Adjustable Control range: MIN, –20 to 0 dB 25  TUNING OPERATIONS Normally, if station signals are strong and there is no interference, quick automatic-search tuning (AUTOMATIC TUNING) is possible. However, if signals of the station you want to select are weak, you must tune to it manually (MANUAL TUNING). L R 1 MANUAL TUNING AUTOMATIC TUNING 1 Select “TUNER” as the input source. TUNER 2 1 Select “TUNER” as the input source. TAPE/MD MONITOR CD PHONO 3 24 Select the reception band (FM or AM) confirming it in the display. TUNER 2 PHONO TAPE/MD MONITOR CD Select the reception band (FM or AM) confirming it in the display. FM/AM FM/AM or or 3 3 TUNING MODE AUTO/MAN'L MONO 4 AUTO To tune to a higher frequency, press the right side once. To tune to a lower frequency, press the left side once. TUNING MODE Turn the “AUTO” indicator off. AUTO/MAN'L MONO 4 Tune to a desired station manually. DOWN DOWN TUNING * If the station where tuning search stops is not the desired one, press again. * If the tuning search does not stop at the desired station (because the signals of the station are weak), change to the MANUAL TUNING method. 26 TUNING UP UP * For a continuous tuning search, press and hold the button. Note If you tune to an FM station manually, it is received in monaural mode automatically to increase the signal quality.  English PRESET TUNING MANUAL PRESET TUNING English This unit can store station frequencies selected by tuning operation. With this function, you can recall any desired station by selecting the preset station number where it is stored. Up to 40 stations (5 groups of 8 stations) can be stored. L R 2,1 4,2 3 To store stations 1 2 To recall a preset station 1 Tune to a desired station. (Refer to the previous page for tuning procedure.) Select the group of preset stations. A/B/C/D/E Select a desired group (A – E) of preset stations confirming it in the display. A/B/C/D/E 2 PRESET Select the preset station number. 1 3 2 3 4 5 6 7 8 MEMORY MEMORY MAN'L/AUTO FM Flashes on and off for about 5 seconds. 4 Select a preset station number where you want to program the station while the “MEMORY” indicator appears in the display. 2 1 3 4 5 6 7 8 STEREO PRESET MHz AUTO 0 20 l00 Notes ● A new setting can be programmed to replace a former setting. ● For presets, the setting of the reception mode (stereo or monaural) is stored along with the station frequency. Memory back-up The memory back-up circuit prevents the programmed data from being lost even if this unit is put in the standby mode, the power plug is disconnected from the AC outlet, or the power is cut due to temporary power failure. If, however, the power is cut for more than one week, the memory may be erased. If so, it can be re-programmed by simply following the PRESET TUNING steps. CONCERT HALL Shows the displayed station has been programmed to A1. * In the same way, program other stations to A2, A3 ... A8. * You can program more stations to preset station numbers on other groups in the same way by selecting other groups in step 2. 27  AUTOMATIC PRESET TUNING You can also make use of an automatic preset tuning function for FM stations only. With this function, this unit performs automatic tuning and stores stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the manual preset tuning method on page 27. L R 2 1 3 To store stations 1 When the automatic preset tuning concludes The display shows the frequency of the last preset station. Check the contents and the number of preset stations by following the procedure of the section “To recall a preset station” on page 27. FM/AM To recall a preset station 2 MEMORY PRESET Follow the procedure in the section “To recall a preset station” on page 27. * A recalled station is shown by the frequency in the display. MAN'L/AUTO FM MEMORY AUTO Press and hold for more than 3 seconds. 3 DOWN TUNING Flashes. UP To tune to higher frequencies, press right side once. To tune to lower frequencies, press left side once. * If the TUNING button is not pressed for a while, automatic preset tuning begins automatically toward higher frequencies. Automatic preset tuning begins from the frequency currently displayed. Received stations are programmed to A1, A2 ... A8 sequentially. * If more than 8 stations are received, they are programmed to the preset station numbers in other groups in alphabetical order. If you want to store the first station received by the automatic preset tuning to a desired preset station number. If, for example, you want to store the first received station to C5, select “C5” by using the A/B/C/D/E button and the preset station number selector buttons after pressing the MEMORY button in step 2. Then press the TUNING button. The first received station is stored to C5, followed by C6, C7, etc. in sequence. If stations are stored up to E8, the automatic preset tuning is automatically concluded. 28 Notes ● You can replace a preset station with another FM or AM station manually by following the procedure in the section “To store stations” on page 27. ● If the number of received stations is not enough to be stored up to E8, the search is finished automatically after searching all frequencies. ● With this function, only stations with sufficient signal strength are stored automatically. If the station you want to program is weak in signal strength, tune to it in monaural manually and program it by following the procedure in the section “To store stations” on page 27.  English EXCHANGING PRESET STATIONS You can exchange the places of two preset stations with each other as shown below. English L R 2, 4 Example) If you want to shift the preset station on E1 to A5, and vice versa. 1 Recall the preset station on E1 (by following the method in “To recall a preset station” on page 27). 4 EDIT 2 PRESET EDIT MEMORY Flashes. 3 Next, recall the preset station on A5 by following the same method as step 1. PRESET Shows the exchange of stations is completed. MEMORY Flashes. 29  REMOTE CONTROL TRANSMITTER You can use the remote control transmitter to control not only this unit but also other components connected to it. The remote control transmitter is factory set to control this unit and most YAMAHA audio components. To control the components of other manufacturers, you must preset the remote control transmitter using the procedure on page 41 and the manufacturers’ codes listed on pages 87 to 91. Components which can be controlled There are eight buttons on the component selector that you can select to control connected components with this remote control transmitter. For example, if CD on the component selector is pressed, the remote control transmitter selects the CD operation mode, allowing the CD player to be operated by the buttons on the remote control transmitter. AMP<TUNER> You can perform the basic operations of this unit, set the speaker level, and set the DSP level and delay time in the AMP<TUNER> mode. CD The code for a YAMAHA CD player is preset. DVD/LD & DVD MENU An LD player can be controlled in the DVD/LD mode. A DVD player can be controlled in the DVD/LD and DVD MENU modes. The code for a YAMAHA DVD player is preset. If the remote control transmitter will not operate your YAMAHA DVD player, you need to preset code number “0048”. TAPE/MD The code for a YAMAHA tape deck is preset. (The code for the YAMAHA MD recorder can also be preset.) VCR A VCR can be controlled. CBL/DBS A cable television or DBS tuner can be controlled. TV A television can be controlled. Notes ● You can preset the code for the manufacturer of your component after pressing the shaded buttons in the illustration above. Note that you can preset only one code for each mode. See “SETUP CODES” on page 41 for details. ● In the DVD/LD and DVD MENU modes: * Be sure to press the component selector button DVD/LD on before presetting the code for the DVD/LD player. The code preset in the DVD/LD mode is also simultaneously preset in the DVD MENU mode. You cannot preset the code for a DVD player in the DVD MENU mode. * DVD MENU operations cannot be performed for some DVD players. ● When using a second (and third) VCR: (See “To use a second (and third) VCR” on page 41 for details.) * If you are not using a CBL/DBS (cable TV or DBS tuner), the second (or third) VCR can be preset in the CBL/DBS mode. * If you are not using a DVD player, the second (or third) VCR can be preset in the DVD MENU mode. Note that in this case you must preset the code for an LD player in the DVD/LD mode even if an LD player is not being used. 30  English The lightly marked buttons do not function. ■ AMP<TUNER> MODE English Press AMP<TUNER>. Input selector These buttons select the program source. CD: To play a CD TUNER: To listen to an FM or AM broadcast TAPE/MD: To play a tape or MD DVD/LD: To play a DVD or LD TV/DBS: To watch a television or satellite broadcast VCR: To play a video tape PHONO: To play an analog record POWER Each time this button is pressed, the unit will switch between the power on and standby modes. TEST This button outputs a test tone for adjusting the output levels of the speakers. 6CH 2CH A/B/C/D/E & PRESET +/– These buttons select a preset FM or AM broadcast. A/B/C/D/E: To select a group of preset stations. PRESET +/–: To select the preset station number. MUTE This button mutes the sound. To cancel mute, press this button once more, or press any operation buttons of this unit. EFFECT This button switches the DSP program on or off. TV VOLUME VOLUME ( ) These buttons adjust the volume level. SLEEP This button sets the SLEEP timer. +/– These buttons adjust the settings of the TIME/ LEVEL mode. TV INPUT PRG+/PRG– These buttons select a DSP program. TIME/LEVEL This button selects the item in the TIME/LEVEL mode. Note TV VOLUME and TV INPUT function if you have preset the code for your TV. 31  The lightly marked buttons do not function. Please refer to the owner’s manual for details of each component. ■ TAPE/MD MODE Press TAPE/MD. POWER (TAPE) When you have preset the code for a YAMAHA tape deck, this button turns the unit on. When you have preset the code for another manufacturer, this button turns on that component if it has a remote control transmitter with a power button. (MD) When you have preset the code for the YAMAHA MD recorder, this button turns the unit on. 6CH 2CH INPUT EFFECT VOLUME MUTE SLEEP REC/PAUSE This button pauses recording on a tape deck or MD recorder. PLAY This button plays a tape or an MD. DIR A (TAPE) This button selects the playing direction of deck A. SKIP – (MD) This button skips to the previous track. REWIND (TAPE) This button rewinds a tape. SEARCH (MD) This button initiates a backward search on the track that is playing to find the point from which you want to listen. Notes TV VOLUME function if you have preset the code for your TV. ● The code for the YAMAHA MD recorder can be preset. ● 32 TV VOLUME DISPLAY (MD) DECK A/B (TAPE) This button selects double-cassette tape deck A or B. PAUSE (MD) This button gives a pause in operation. DIR B (TAPE) This button selects the playing direction of deck B. SKIP + (MD) This button skips to the next track. STOP This button stops operation of a tape or MD. FAST FORWARD (TAPE) This button winds a tape fast forward. SEARCH (MD) This button initiates a fast-forward search on the track that is playing to find the point from which you want to listen.  ■ CD MODE English English The lightly marked buttons do not function. Please refer to the owner’s manual for details of each component. Press CD. POWER When you have preset the code for a YAMAHA CD player, this button turns the unit on. When you have preset the code for another manufacturer, this button turns on that component if it has a remote control transmitter with a power button. 6CH 2CH INPUT EFFECT DISC SKIP +/– (for the CD player with CD changer) These buttons skip to the next or previous CD. VOLUME MUTE SLEEP PLAY This button plays a CD. SKIP – This button skips to the previous track. SEARCH This button initiates a backward search on the track that is playing to find the point from which you want to listen. TV VOLUME DISPLAY TV INPUT PAUSE This button gives a pause in operation. The button functions as PAUSE/STOP* for operating YAMAHA CD player under factory setting. SKIP + This button skips to the next track. STOP This button stops operation. The button functions as PAUSE/STOP* for operating YAMAHA CD players. SEARCH This button initiates a fast-forward search on the track that is playing to find the point from which you want to listen. * PAUSE/STOP function ... Press once to give a pause an operation and once more to stop operation. Note TV VOLUME and TV INPUT function if you have preset the code for your TV. 33  The lightly marked buttons do not function. Please refer to the owner’s manual for details of each component. ■ DVD/LD MODE Press DVD/LD. POWER (DVD) When you have preset the code for a YAMAHA DVD player, this button turns the unit on. When you have preset the code for another manufacturer, this button turns on that component if it has a remote control transmitter with a power button. (LD) When you have preset the code for a YAMAHA LD player, this button turns the VOLUME unit on. When you have preset the code for another manufacturer, this button turns MUTE on that component if it has a remote control transmitter with a power button. SLEEP INPUT 6CH 2CH EFFECT DISC SKIP +/– TV VOLUME DISPLAY TV INPUT PAUSE SKIP+ PLAY SEARCH SKIP– STOP SEARCH Note TV VOLUME and TV INPUT function if you have preset the code for your TV. ■ DVD MENU MODE Press DVD MENU. POWER When you have preset the code for a YAMAHA DVD player, this button turns the unit on. When you have preset the code for another manufacturer, this button turns on that component if it has a remote control transmitter with a power button. 6CH 2CH Numeric buttons CLEAR +10 DISC SKIP +/– VOLUME MUTE RETURN MENU UP INDEX TV INPUT MENU LEFT MENU RIGHT MENU SELECT MENU DOWN TITLE Note TV VOLUME and TV INPUT function if you have preset the code for your TV. 34 TV VOLUME MENU  ■ VCR MODE ■ TV MODE English English The lightly marked buttons do not function. Please refer to the owner’s manual for details of each component. Press VCR. Press TV. VCR POWER TV POWER CHANNEL CHANNEL 6CH 2CH 6CH 2CH EFFECT VCR CHANNEL +/– VOLUME EFFECT CHANNEL ENTER MUTE TV VOLUME TV SLEEP VCR REC Press this button twice to start recording. DISPLAY TV INPUT VCR PAUSE VCR PLAY VCR REWIND CHANNEL ENTER TV CHANNEL +/– VOLUME TV MUTE TV SLEEP VCR REC Press this button twice. VCR PLAY VCR STOP VCR FAST FORWARD VCR REWIND Note TV VOLUME, TV INPUT and TV SLEEP function if you have preset the code for your TV. TV VOLUME DISPLAY TV INPUT VCR PAUSE VCR STOP VCR FAST FORWARD Note You can control your VCR if you have preset the code for it. ■ CBL/DBS MODE Press CBL/DBS. CBL/DBS POWER CHANNEL 6CH 2CH +100 CHANNEL ENTER CBL/DBS CHANNEL +/– VOLUME MUTE TV SLEEP TV VOLUME DISPLAY TV INPUT MENU LEFT MENU SELECT RECALL MENU UP MENU RIGHT MENU DOWN MENU Note TV VOLUME, TV INPUT and TV SLEEP function if you have preset the code for your TV. 35  USING DIGITAL SOUND FIELD PROCESSOR (DSP) This unit incorporates a sophisticated, multi-program digital sound field processor. The processor allows you to electronically expand and change the shape of the audio sound field from both audio and video sources, creating a theater-like experience in your listening room. You can create an excellent audio sound field by selecting a suitable sound field program (this will, of course, depend on what you will be listening to), and adding desired adjustments. In addition, this unit incorporates a Dolby Pro Logic Surround decoder for multi-channel sound reproduction of sources encoded with Dolby Surround. The operation of the Dolby Pro Logic Surround decoder can be controlled by selecting a corresponding DSP program including a combined operation of Yamaha DSP and Dolby Pro Logic Surround. Brief Overview of Digital Sound Field Programs The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in mind that most of these are precise digital recreations of actual acoustic environments. The data for these sound fields was recorded at actual locations using sophisticated sound field measurement equipment. Note The channel level balance between the left and right rear effect speakers may vary depending on the sound field you are listening to. This is due to the fact that most of these sound field recreations are actual acoustic environments. PROGRAM PRO LOGIC PRO LOGIC ENHANCED This program is used for playback of sources encoded with Dolby Surround. The application of a sophisticated digital signal processing system reduces crosstalk and directs or steers the sound source more smoothly and precisely, as compared to conventional types. This program is also used for playback of sources encoded with Dolby Surround. Enhancing the “Normal” Dolby Pro Logic, the DSP technology simulates the multi-surround speaker systems of a 35 mm movie theater. This effect creates a wide surround sound field, and expands the sound stage with an improved presence image. This program is used for musical based movies, as well as drama and comedy based movies. CONCERT VIDEO This program is effective for music videos and gives excellent depth and clarity for vocals. For opera, the orchestra and stage are ideally recreated, letting you feel as if you were in an actual concert hall. MONO MOVIE This program is designed specifically to enhance mono source programs. Compared to a strictly mono setting, the sound image created in this mode is wider and slightly forward of the speaker pair, lending an immediacy to the overall sound. It is particularly effective when used with old mono movies, news broadcasts and dialog. TV SPORTS 36 FEATURE This program is furnished with a tight sound field in which the sound will not spread excessively on the front side, but the rear surround side produces a dynamic sound expansion. This program is the most suitable for sports programs. DISCO This program recreates the acoustic environment of a lively disco in the heart of a very lively city. The sound is dense and highly concentrated. It is also characterized by a high-energy, “immediate” sound. ROCK CONCERT This program is ideally suited for rock music. You will experience a very dynamic or lively sound field. CONCERT HALL In this program, the center will appear to be deep behind the main speakers, creating an expansive large hall ambience. Orchestra and opera music are suited for this sound field.  English Applying a digital sound field processor (DSP) effect to an audio source l6 20 l2 28 8 4 40 2 60 0 –dB 2 2 Press the component selector button AMP<TUNER> on the remote control transmitter. 1 2 Follow steps 1 to 6 of the procedure shown in “TO PLAY A SOURCE” on page 22. Select a program that is suitable for the source. PRO LOGIC ENHANCED Notes ● Program selection can be made to individual input sources. Once you select a program, it is linked with the input source selected at that time. So, the next time you select the input source, the same program is automatically recalled. ● If you prefer to cancel the DSP, press the EFFECT button. The sound will be the normal 2-channel stereo without surround sound effect. ● When CONCERT VIDEO, MONO MOVIE, TV SPORTS, DISCO, ROCK CONCERT or CONCERT HALL is selected, no sound is heard from the center speaker. ● When a monaural sound source is played with DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED, no sound is heard from the rear speakers. ● When this unit’s Dolby Pro Logic Surround decoder is used, if the main-source sound is considerably altered by overadjustment of the BASS or TREBLE control, the relationship between the center and rear channels may produce an unnatural effect. ● To select a DSP program on the remote control transmitter, first turn the DSP on so that a program name lights up in the display by pressing the EFFECT button. Next, select a desired DSP program by pressing the PRG+ or PRG– operation buttons. PRO LOGIC The selected mode indicator lights in the display. 3 If desired, adjust the delay time and the output level of each speaker. (For details, refer to the descriptions on pages 38 and 39.) 37  Adjustment of the CENTER LEVEL If desired, you can adjust the sound output level of the center speaker even if the output level is already set in “SPEAKER BALANCE ADJUSTMENT” on page 19. 1 Notes ● This adjustment can be made only when the digital sound field program DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED is selected. ● Once the output level is adjusted, the level value will be the same in all of the digital sound field programs. Press repeatedly until “CENTER” appears on the display. DELAY/CENTER/ REAR/SWFR 2 Pressing and holding the “+” or “–” side of the TIME/LEVEL button continuously changes the level value. The value stops changing momentarily at the preset point (0 dB). TIME/LEVEL Adjustable Control range: MIN, –20 to +10 dB Adjustment of the REAR LEVEL If desired, you can adjust the sound output level of the rear speakers even if the output level is already set in “SPEAKER BALANCE ADJUSTMENT” on page 19. 1 Press repeatedly until “REAR” appears on the display. DELAY/CENTER/ REAR/SWFR 2 Pressing and holding the “+” or “–” side of the TIME/LEVEL button continuously changes the level value. The value stops changing momentarily at the preset point (0 dB). TIME/LEVEL Adjustable Control range: MIN, –20 to +10 dB 38 Notes ● This adjustment can be made only when the built-in digital sound field processor is on. ● Once the output level is adjusted, the level value will be the same in all the digital sound field programs.  You can adjust the time difference between the beginning of the sound from the main speakers and the beginning of the effect sound from the rear speakers. The larger the value, the later the effect sound is generated. This adjustment can be made to all programs individually. : from 15 to 30 milliseconds (Preset value: 20 milliseconds) PRO LOGIC : from 15 to 30 milliseconds ENHANCED (Preset value: 20 milliseconds) CONCERT VIDEO : from 1 to 100 milliseconds (Preset value: 28 milliseconds) MONO MOVIE : from 1 to 100 milliseconds (Preset value: 20 milliseconds) TV SPORTS : from 1 to 50 milliseconds (Preset value: 45 milliseconds) DISCO : from 1 to 100 milliseconds (Preset value: 14 milliseconds) ROCK CONCERT : from 1 to 100 milliseconds (Preset value: 17 milliseconds) CONCERT HALL : from 1 to 100 milliseconds (Preset value: 30 milliseconds) 1 Press repeatedly until “DELAY” appears on the display. English Adjustment of DELAY TIME DELAY/CENTER/ REAR/SWFR ms PRO LOGIC 2 Pressing and holding the “+” or “–” side of the TIME/LEVEL button continuously changes the value. The value stops changing momentarily at the preset point. TIME/LEVEL ms Adjustable Notes When the TIME/LEVEL button is pressed, sound is momentarily interrupted. ● Adding too much delay will cause an unnatural effect with some sources. ● To adjust the delay time of the selected DSP program on the remote control transmitter, press the + and – operation buttons. ● Note The values of the delay time, center level, rear level and subwoofer output level you set will remain memorized even when this unit is in the standby mode. However, if the power cord is kept disconnected for more than one week, these values will be automatically changed back to the original factory settings. 39  SETTING THE SLEEP TIMER If you use the SLEEP timer of this unit, you can have this unit automatically put in the standby mode after a set period of time. When you want to go to sleep while enjoying a broadcast or other desired input source, this timer function is helpful. Notes ● The SLEEP timer can be controlled only with the remote control transmitter. ● The components on which the SLEEP timer is effective are the sources connected to the SWITCHED AC OUTLET(S) on the rear panel of this unit. To set the SLEEP time To cancel the selected SLEEP time 1 Press repeatedly to select the desired SLEEP time. Press repeatedly until “SLEEP OFF” appears in the display. (It will soon disappear and the “SLEEP” indicator will go off from the display.) Indicates the SLEEP time. SLEEP CONCERT HALL Lights up. Whenever the SLEEP button is pressed, the SLEEP time will change as follows. (Minutes) 120 90 60 30 The SLEEP timer is off (OFF). (The state before the SLEEP button is pressed.) After a while, the display returns to the indication displayed before the SLEEP timer was set. 2 40 The unit will be turned into the standby mode automatically at the selected SLEEP time. Note The SLEEP timer setting can also be canceled by putting this unit into the standby mode with the STANDBY/ON switch on the front panel (or the POWER /I button on the remote control transmitter) or disconnecting the power plug of this unit from the AC outlet.  English SETUP CODES Presetting the remote control transmitter Perform the presetting procedure for each component you want to control with the remote control transmitter. Note If your component does not respond to any of the codes listed for the manufacturer, use the original remote control transmitter that was supplied with the component. To control your components (MD recorder, DVD player, TV, etc.) 1. Turn on the component to be used. 2. Press the component selector button that matches the component to be controlled (TAPE/MD, DVD/LD, TV etc.). To use a second (and third) VCR Returning to the factory-set codes You can control a second (and/or third) VCR in the CBL/DBS and DVD MENU modes if a CBL (or DBS) or DVD player is not being used. To return all components to the factory-set codes, follow these steps. 1. Press a component selector button other than AMP<TUNER>. ) 2. Press both VOLUME buttons ( for about four seconds at the same time so that the indicator flashes twice. 3. Enter the code number “9990”. 4. Make sure that the indicator flashes twice. If you want to control a second (and/or third) VCR in the DVD MENU mode, you must preset the code for an LD player in that mode. 1. Turn on the VCR to be used. 2. Press the component selector button CBL/DBS or DVD MENU. ) 3. Press both VOLUME buttons ( at the same time for about four seconds so that the indicator flashes twice. ) 3. Press both VOLUME buttons ( at the same time for about four seconds so that the indicator flashes twice. 4. Use the numeric buttons to enter the four-digit manufacturer’s code for the component to be used. Make sure that the indicator flashes twice. If the indicator does not flash, repeat step 3 and re-enter the code. 6CH 2CH 5. Press POWER (or any other button) on the remote control transmitter to check if you have preset the code correctly. If the component cannot be controlled by the remote control transmitter, try entering another code for the same manufacturer. To return each component to the factoryset codes, follow these steps. 1. Press the component selector that matches the component to be returned to the factory-set codes. 2. Press both VOLUME buttons ( ) at the same time for about four seconds so that the indicator flashes twice. 3. Enter the code number “0000”. 4. Make sure that the indicator flashes twice. The following codes are preset by the factory. Factory-set codes 4. Use the numeric buttons to enter the four-digit code for the second (or third) VCR. Make sure that the indicator flashes twice. If the indicator does not flash, repeat step 3 and re-enter the code. 6CH 2CH Component Component Code TV TV 0101 CBL/DBS DBS tuner 0006 VCR VCR 0002 selector DVD/LD DVD player 0008 YAMAHA CD CD player 0005 YAMAHA TAPE/MD Tape deck 0004 YAMAHA We recommend that you write all code numbers you have preset on the “Quick Reference Card”. 5. Press POWER (or any other button) on the remote control transmitter to check if you have preset the code correctly. If the VCR cannot be controlled by the remote control transmitter, try entering another code for the same manufacturer. 41  TROUBLESHOOTING If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service center for help. SYMPTOM Firmly plug in the power cord. The IMPEDANCE SELECTOR switch on the rear panel is not set to the right or the left end firmly. Set the switch to the right or the left end firmly. It happens that this unit does not work normally. There is an influence of strong external noise (lightning, excessive static electricity, etc.) or a misoperation on this unit while using this unit. Turn this unit into the standby mode and disconnect the AC power cord from the AC outlet. After about 30 seconds, connect the power and operate this unit again. No sound or no picture. Incorrect output cord connections. Connect the cords properly. If the problem persists, the cords may be defective. Appropriate input source is not selected. Select an appropriate input source with the input selector buttons. The SPEAKERS switches are not set properly. Set the SPEAKERS switch which corresponds to the speakers to be used to the ON position. Speaker connections are not secure. Secure the connections. The protection circuit has been activated because of short circuit etc. Turn this unit into the standby mode, and then turn on to reset the protection circuit. Amplifier The SLEEP timer has functioned. Cancel the SLEEP timer function. Only one side speaker outputs the sound. Incorrect setting of the BALANCE control. Adjust it to the appropriate position. Incorrect cord connections. Connect the cords properly. If the problem persists, the cords may be defective. Sound “hums”. Incorrect cord connections. Firmly connect the audio plugs. If the problem persists, the cords may be defective. No connection from the turntable to the GND terminal. Make the GND connection between the turntable and this unit. The volume level is low while playing a record. The record is being played on a turntable with an MC cartridge. The player should be connected to the unit through the MC head amplifier. The volume level cannot be increased, or sound is distorted. The component connected to the REC OUT terminals of this unit is turned off. Turn the power to the component on. No sound from the rear speakers. The sound output level to the rear speakers is set to minimum. Raise the sound output level to the rear speakers. The monaural sound source is played in DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED mode. Select another program suitable for the monaural sound source. The sound output level to the center speaker is set to minimum. Raise the sound output level to the center speaker. The center channel mode is in PHANTOM mode. Select NORMAL or WIDE. Incorrect sound field program selection. Select the appropriate program. FM stereo reception is noisy. Because of the characteristics of FM stereo broadcasts, this is limited to cases where the transmitter is too far away or the antenna input is poor. Check the antenna connections. Try using a high quality directional FM antenna. Set the TUNING MODE button to the manual tuning mode. There is distortion and clear reception cannot be obtained even with a good FM antenna. There is multipath interference. Adjust antenna placement to eliminate multipath interference. A desired station cannot be tuned in with the automatic tuning method. The station is too weak. Use the manual tuning method. Use a high quality directional FM antenna. Previously preset stations can no longer be tuned in. This unit has been unplugged for a long period. Repeat the presetting procedure. A desired station cannot be tuned in with the automatic tuning method. Weak signal or loose antenna connections. Tighten the AM loop antenna connections and rotate it for best reception. There are continuous crackling and hissing noises. Noises will result from lightning, fluorescent lamps, motors, thermostats and other electrical equipment. Use an outdoor antenna and a ground wire. This will help somewhat but it is difficult to eliminate all noise. There are buzzing and whining noises (especially in the evening). A television set is being used nearby. Relocate this unit away from the TV. The remote control transmitter does not work. Direct sunlight or lighting (of an inverter type of fluorescent lamp etc.) is striking the remote control sensor of the main unit. Change the position of the main unit. The batteries of this remote control transmitter are too weak. Replace the batteries with new ones. The component to be controlled has not been selected. Press the component selector which matches the component to be controlled. The proper manufacturer’s code for the component to be controlled has not been set. Try entering another code for the same manufacturer. The manufacturer’s code has not been set properly. Set the code again. This unit is in the standby mode. Turn the power to this unit on. Remote control transmitter AM FM No sound from the center speaker. Others REMEDY Power cord is not plugged in or is not completely inserted. The sound suddenly goes off. 42 CAUSE The unit fails to turn on when the STANDBY/ON switch is pressed, or turns into the standby mode suddenly soon after the power is turned on. Use the manual tuning method. The sound is degraded when listening with the headphones connected to the compact disc player or cassette deck that are connected with this unit.  AUDIO SECTION Minimum RMS Output Power per Channel (Power Amp. Section) (When both channels are driven) Main L, R 8 ohms, 20 Hz to 20 kHz, 0.04% THD ......................... 60 W + 60 W Center 8 ohms, 20 Hz to 20 kHz, 0.04% THD ...................................... 60 W Rear L, R 8 ohms, 20 Hz to 20 kHz, 0.04% THD ......................... 60 W + 60 W Minimum RMS Output Power per Channel (Power Amp. Section) (When both channels are driven) Main L, R 8 ohms, 1 kHz, 0.07% THD ......................................... 70 W + 70 W Center 8 ohms, 1 kHz, 0.07% THD ...................................................... 70 W Rear L, R 8 ohms, 1 kHz, 0.07% THD ......................................... 70 W + 70 W Input Sensitivity/Impedance PHONO (MM) ...................................................... 2.5 mV/47 k-ohms CD/TAPE·MD/DVD·LD/TV·DBS/VCR ................. 150 mV/47 k-ohms 6CH DISCRETE INPUT (EXTERNAL DECODER) MAIN L/R ......................................................... 150 mV/47 k-ohms CENTER ......................................................... 150 mV/40 k-ohms REAR L/R ........................................................ 150 mV/40 k-ohms SUBWOOFER ................................................. 150 mV/40 k-ohms Maximum Input Signal PHONO (MM) 1 kHz, 0.1% THD ................................................ 100 mV or more CD/TAPE·MD/DVD·LD/TV·DBS/VCR (EFFECT ON) 1 kHz, 0.5% THD .................................................... 2.2 V or more Output Level/Impedance REC OUT ........................................................... 150 mV/2.7 k-ohms SUBWOOFER (EFFECT OFF) ................................. 5 V/1.2 k-ohms Maximum Power (EIAJ) [China and General models only] (When both channels are driven) Main L, R 8 ohms, 1 kHz, 10% THD ............................................ 95 W + 95 W Center 8 ohms, 1 kHz, 10% THD ......................................................... 95 W Rear L, R 8 ohms, 1 kHz, 10% THD ............................................ 95 W + 95 W Headphone Jack Rated Output Level/Impedance (1 kHz, 8 ohms, 150 mV) ...................................... 0.43 V/ 330 ohms Dynamic Power per Channel (by IHF Dynamic Headroom measuring method) Main L, R 8 ohms ......................................................................... 80 W + 80 W 6 ohms ..................................................................... 100 W + 100 W 4 ohms ..................................................................... 120 W + 120 W 2 ohms .................................................................... 145 W + 145 W Total Harmonic Distortion (20 Hz to 20 kHz) PHONO (MM) to REC OUT 1 V ........................................................................... 0.02% or less CD/TAPE·MD/DVD·LD/TV·DBS/VCR (EFFECT OFF) to SP OUT 30 W/8 ohms ......................................................... 0.025% or less DIN Standard Output Power per Channel [Europe model only] Main L, R 4 ohms, 1 kHz, 0.7% THD ....................................... 100 W + 100 W Center 4 ohms, 1 kHz, 0.7% THD ...................................................... 100 W Rear L, R 4 ohms, 1 kHz, 0.7% THD ....................................... 100 W + 100 W Dynamic Headroom [U.S.A. and Canada models only] 8 ohms .................................................................................. 1.55 dB IEC Power [Europe model only] Main L, R 8 ohms, 1 kHz, 0.04% THD ......................................... 65 W + 65 W Power Band Width Main L, R 8 ohms, 30 W, 0.1% THD ....................................... 10 Hz to 50 kHz Damping Factor (SPEAKERS A) Main L, R 8 ohms, 20 Hz to 20 kHz .................................................. 60 or more English SPECIFICATIONS Frequency Response (20 Hz to 20 kHz) CD/TAPE·MD/DVD·LD/TV·DBS/VCR ............................... 0 ± 0.5 dB RIAA Equalization Deviation PHONO (MM) ................................................................... 0 ± 0.5 dB Signal-to-Noise Ratio (IHF-A Network) PHONO (MM) to REC OUT (5 mV Input Shorted) [U.S.A., Canada, China, and General models] ...... 86 dB or more [Australia, U.K., and Europe models] ..................... 81 dB or more CD/TAPE·MD/DVD·LD/TV·DBS/VCR to MAIN SP OUT (150 mV Input Shorted, EFFECT OFF) .................. 96 dB or more Residual Noise (IHF-A Network) MAIN L/R to SP OUT ................................................. 150 µV or less Channel Separation (Vol. –30 dB, EFFECT OFF) PHONO (Input Shorted, 1 kHz/10 kHz) ........ 60 dB or more/55 dB or more CD/TAPE·MD/DVD·LD/TV·DBS/VCR (Input 5.1 k-ohms shorted, 1 kHz/10 kHz) ....................................................... 60 dB or more/45 dB or more Tone Control Characteristics BASS: Boost/cut ................................................. ±10 dB, 50 Hz Turnover Frequency ............................................ 350 Hz TREBLE: Boost/cut ............................................... ±10 dB, 20 kHz Turnover Frequency ........................................... 3.5 kHz Filter Characteristics Subwoofer (L.P.F.) ......................................... fc = 150 kHz, 6 dB/oct. 43  VIDEO SECTION AM SECTION Video Signal Level ........................................................ 1 Vp-p/75 ohms Tuning Range [U.S.A. and Canada models] ....................................... 530 to 1710 kHz [China and General models] (frequency step 10 kHz) .......................................... 530 to 1710 kHz (frequency step 9 kHz) ............................................ 531 to 1611 kHz [Australia, U.K., and Europe models] ........................... 531 to 1611 kHz Maximum Input Level .................................................. 1.5 Vp-p or more Signal-to-Noise Ratio ...................................................... 50 dB or more Monitor Output Frequency Response ................ 5 Hz to 10 MHz, –3 dB Usable Sensitivity ................................................................... 300 µV/m FM SECTION Tuning Range [U.S.A. and Canada models] .................................... 87.5 to 107.9 MHz [China and General models] (frequency step 100 kHz) ..................................... 87.5 to 108.0 MHz (frequency step 50 kHz) ................................... 87.50 to 108.00 MHz [Australia, U.K., and Europe models] ................... 87.50 to 108.00 MHz Output Level (30% mod., 1 kHz) ................................................................ 150 mV 50 dB Quieting Sensitivity (S/N 50 dB, 1 kHz, 100% Mod.) [U.S.A., Canada, China and General models only] IHF, Mono ............................................................................... 1.6 µV IHF, Stereo .............................................................................. 23 µV GENERAL Usable Sensitivity (75 ohms) [Australia, U.K., and Europe models only] DIN, Mono (S/N 26 dB) .......................................................... 0.9 µV DIN, Stereo (S/N 46 dB) ......................................................... 28 µV Signal-to-Noise Ratio .................................................................... 52 dB Antenna Input ................................................................... Loop antenna Power Supply [U.K. and Europe models] ........................................... AC 230 V, 50 Hz [U.S.A. and Canada models] ...................................... AC 120 V, 60 Hz [Australia model] ......................................................... AC 240 V, 50 Hz [China model] .............................................................. AC 220 V, 50 Hz [General model] ................................. AC 110/120/220/240 V, 50/60 Hz Alternate Channel Selectivity (±400 kHz) [U.S.A., Canada, China and General models only] ....................... 75 dB Power Consumption [U.K., Europe, China, Australia and General models] .................. 260 W [U.S.A. model] .............................................................................. 240 W [Canada model] ............................................................... 260 W/340 VA Selectivity (two signals, 40 kHz Dev. ±300 kHz) [Australia, U.K., and Europe models only] .................................... 55 dB Maximum Power Consumption (10% THD, When 5 channels are driven) [General model only] .................................................................... 630 W Signal-to-Noise Ratio (DIN-Weighted, 40 kHz Dev.) [Australia, U.K., and Europe models only] Mono/Stereo ................................................................. 75 dB/69 dB AC Outlets 2 SWITCHED OUTLETS [Europe, Canada, U.S.A., China and General models] ........................................................................... 100 W max. total 1 SWITCHED OUTLET [U.K. and Australia models] .................................... 100 W max. total Signal-to-Noise Ratio (IHF) [U.S.A., Canada, China and General models only] Mono/Stereo ................................................................. 81 dB/75 dB Harmonic Distortion Mono/Stereo (1 kHz) ....................................................... 0.1%/0.2% Dimensions (W x H x D) ........................................ 435 x 151 x 391 mm (17-1/8” x 5-15/16” x 15-3/8”) Weight ................................................................. 10.5 kg (23 lbs. 2 oz.) Stereo Separation (1 kHz) ............................................................ 48 dB Frequency Response (20 Hz to 15 kHz) .................................................................. 0 ±1 dB Output Level [Australia, U.K., and Europe models] (40 kHz Dev., 1 kHz) ............................................................. 550 mV [U.S.A., Canada, China and General models] (100% mod., 1 kHz) .............................................................. 550 mV Antenna Input ........................................................ 75 ohms unbalanced 44 Accessories ................................................................. AM loop antenna Indoor FM Antenna 75-ohm/300-ohm antenna adapter [U.K. model only] Antenna adapter [U.S.A. and Canada models only] Remote control transmitter Batteries Specifications are subject to change without notice.  TV 1001 0941, 1031 0271, 1001 0331, 1001, 1071 0891, 1031 0881 0951, 1011 0941 0941 1001 0331 0001, 0021, 0061, 0071, 0081, 0091, 0111, 0811, 0821, 0831, 0841, 0851, 0861, 0871, 0901, 0921, 0941, 0981, 1011, 1031, 1051, 1081, 1091 Envision 0361, 1111 Erres 1001 Etron 0331 Ferguson 1001 Finlux 1001 Fisher 0171, 0801, 0981 Formenti 0441 Formonti 1001 Fortress 1141 Fujitsu 1091 Funai 1051, 1091, 1341, 1361, 1411, 1451, 1501, 1521 Futuretech 1051 GE 0131, 0161, 0201, 0751, 0761, 0771, 0781, 0791, 0811, 0861, 1041 GEC 0271, 1001 Gemini 0391 Genexxa 0431 Gibralter 0891, 1031, 1111 GoldStar 0031, 0121, 0351, 0411, 0731, 0741, 0861, 0941, 0971, 1001, 1031, 1111, 1151 Goodmans/Tashiko 0271, 0661, 1001 Granada 1001 Grundig 1781, 1791, 1801, 1811, 1821, 1831, 1841, 1851, 1861, 1871, 1881 Gunpy 1051, 1091 H/K 0721 Hallmark 0861 Hanseatic 1001 Harvard 1051, 1061 Hinari 1001, 1091 Hitachi 0181, 0351, 0671, 0681, 0691, 0701, 0711, 0871, 0941, 0971, 1351 Hypson 1001 Ima 1051 Indiana 1001 Infinity Reference 0101 Interfunk 1001 ITT 0611 Janeil 1131 JBL 0101 JCB 0951 Jensen 0311 Jinxing 1531, 1541, 1551, 1561, 1571, 1621, 1631, 1641, 1651, 1691, 1731 JVC 0261, 0281, 0641, 0651, 0661, 0841 Kawasho 0901 Kaypani 1021 Kenwood 0361, 1031, 1111 Kloss 0631, 0721, 1131 KTV 0921, 0941, 1011, 1051, 1111 Leyco 1001 Liesenk & Tter 1001 Lloytron 0941 Loewe 1001 Logik 0991, 1771 Luxman 0351, 0971 Lxi 0101, 0621, 0761, 0861, 0981 Magnavox 0101, 0341, 0391, 0401, 0411, 0421, 0581, 0591, 0601, 0611, 0631, 0661, 0961, 1111 Majestic 0991 Marantz 0101, 0221, 0361, 1001, 1111 Mark 1001 Matsui 0271, 0331, 1001 Mediator 1001 Megatron 0691, 0861, 1161 MEI 1011 M Electronic 1001 Memorex 0331, 0571, 0861, 0971, 0981, 0991, 1771 Metz 1791, 1831, 1891, 1901, 1911, 1921, 1931, 1941 MGA 0361, 0561, 0571, 0861, 1031, 1111 Midland 0751, 0761, 0891, 0941, 1151 Mitsubishi 0221, 0321, 0561, 0571, 0661, 0861, 1031, 1101, 1381 Montgomery 1091 Motorola 1041, 1141 MTC 0351, 0361, 0881, 0931, 0971, 1011, 1031, 1111 Multitech 0881, 1051 NAD 0551, 0621, 0861 NEC 0241, 0351, 0361, 0661, 0971, 1031, 1111, 1321, 1711 Français A-Mark 1161 A Tandy 0941 Abex 1151 Admira 1141 Adventura 1131 Aiko 1121 Akai 0331, 1101, 1111 Alba 0431 Alleron 1091 Ambassador 1081 Amstrad 0481, 1081 Anam 0251, 1041, 1051, 1061, 1071 Anam National 1041 AOC 0361, 1021, 1031, 1111, 1161 Archer 1161 Audiosonic 1001 Audiovox 1051, 1161 Awai 1481 Bauer 0441 Baur 1001 Beijing 1511, 1551, 1561 Belcor 1031 Bell & Howell 0981, 0991 Beon 1001 Bradford 1051 Brockwood 1031 Broksonic 1161 Bush 1001 Candle 0351, 0361, 0961, 0971, 1111, 1131 Capehart 1021 Carver 0101 Cathay 1001 Celebrity 0951 Centurion 0411 Changhong 1541, 1551, 1561, 1621 Citizen 0351, 0361, 0921, 0931, 0941, 0961, 0971, 1111, 1121, 1131 Clairtone 1011 Clarivox 1001 Concerto 0351, 0971 Conrowa 1751 Contec 0901, 0911, 1011, 1051 Corando 0941 Craig 0251, 1051 Crown 0941, 1051 Curtis Mathes 0161, 0361, 0931, 0941, 0981, 1111 CXC 1051 Daewoo 0291, 0301, 0331, 0721, 0941, 1001, 1031, 1121, 1191, 1531, 1581, 1591, 1601 Dansai Daytron Decca Dixi Dumont Dynatech Electroband Electrohome Electron Elin Elta Emerson English LIST OF MANUFACTURER’S CODES LISTES DES CODES FABRICANT 87  Neckermann Nei Nikkai Nikko Novabeam NTC Onwa Optimus Optonica Orion Osaki Otto Versand Panasonic 1001 1001 0271, 0431, 1001, 1151 0861, 1111, 1121 0721 1121 1051 0551 0541, 1141 0831, 1001 0271, 1151 1001 0101, 0191, 0251, 0751, 1041, 1311, 1371, 1431 Panda 1541, 1721 Penny 0161, 0361, 0521, 0531, 0621, 0731, 0751, 0761, 0781, 0791, 0861, 0931, 0941, 1031, 1041, 1111, 1151, 1161 Peony 1561, 1621 Philco 0361, 0581, 0591, 0601, 0611, 0631, 0961, 1031, 1111 Philips 0101, 0401, 1001 Phonola 1001 Pilot 0941, 1031, 1111 Pioneer 0511, 0551, 0871, 1331 Portland 0941, 1031, 1121 Priceclub 0931 Prism 0751 Proscan 0761 Protech 1001 Proton 0501, 0861, 0941, 1021, 1161 Pulsar 0891 Pulser 1031 Quasar 0251, 0751, 1041 Quelle 1001 Radio Shack 0541, 0941, 1031, 1051, 1151 Radiola 1001 RCA 0051, 0141, 0151, 0181, 0411, 0491, 0531, 0761, 0771, 0871, 1031 Realistic 0541, 0861, 0941, 0971, 0981, 1031, 1051, 1111, 1151 Rhapsody 1011 R-line 1001 Runco 0891, 1111 Saisho 0331, 1081 Sampo 0361, 0941, 1021, 1111, 1151 Samsung 0331, 0341, 0351, 0361, 0861, 0931, 0941, 0971, 1001, 1031, 1111, 1151, 1461 Samsux 0941 Sanyo 0171, 0231, 0271, 0661, 0801, 0911, 0981, 1231, 1251, 1261 88 SBR Schneider Scimitsu Scotch Scott 1001 1001 1031 0861 0831, 0861, 0941, 1031, 1051, 1091 Sears 0101, 0161, 0171, 0351, 0481, 0521, 0621, 0761, 0801, 0861, 0971, 0981, 1091 Shanghai 1561, 1681 Sharp 0461, 0471, 0541, 0661, 0911, 0941, 1141, 1241, 1271 Shogun 1031 Signature 0991, 1771 Simpson 0581, 0961 Solavox 1151 Sonoko 1001 Sontec 1001 Sony 0371, 0451, 0661, 0841, 0951, 1281, 1441 Soundesign 0861, 0961, 1051, 1091 Soundwave 1001 Spectricon 1161 Squareview 0481 SSS 1031, 1051 Star-lite 1051 Suprem 0951 Supre-macy 1131 Surpa 0351, 0971 Sylvania 0101, 0361, 0441, 0581, 0591, 0601, 0611, 0631, 0961, 1111 Symphonic 0481 Sysline 1001 Tandy 0271, 0431, 1141 Tatung 0271, 0881, 1001, 1041, 1161 Tcl 1561, 1631, 1701 Technics 0751 Techwood 0351, 0751, 0971 Teknika 0101, 0351, 0571, 0931, 0941, 0961, 0971, 0991, 1031,1051, 1091, 1121, 1131, 1771 Teletech 0331 Tera 0501 Thakral 1671 Thorm 1001 TMK 0351, 0861, 0971, 1081 Toshiba 0381, 0521, 0621, 0661, 0931, 0981, 1301 Tosonic 1011 Totevision 0941 Trical 0911 Universal 0781, 0791 Universum 1001 Vector Research 0361, 1111 Vestel 1001 Victor 0651, 1201, 1211, 1221 Video Concept 1101 Vidikron 0101, 0211 Vidtech 0861, 1031 Viking 1131 Wards 0101, 0361, 0451, 0541, 0581, 0591, 0601, 0611, 0771, 0781, 0791, 0861, 0971, 0991, 1031, 1091, 1111, 1771 Watson 1001 Xogego 1611, 1621, 1661, 1741, 1761 Yamaha 0221, 0361, 0571, 1031, 1111, 1141, 1381 Yoko 1001 Zenith 0011, 0041, 0891, 0991, 1771 Zonda 1161 CABLE ABC Antronix Archer BBT Cabletime Cablevision Colour Voice Comtronics Eagle Comronics Eastern Electricord Electus GE GEC Cable System Hamlin H5 Hamlin H6 Hamlin H6S Hamlin H8 Hamlin H9 Jerrold Jerrold 400L Jerrold 450L Jerrold 550 Jerrold Osd Catv Jerrold Sprucer Magnavox/Philips Mamm Memorex Movie Time Northcoast NSC Oak Oak Sigma 450 Oak Sigma 550 Panasonic TZ 120/130 Panasonic TZ 170/180 Panasonic TZ140 Panasonic TZ150/160 Paragon 0256, 0376 0136 0136, 0286 0076 0166 0196 0306, 0346 0216, 0276 0276 0066 0206 0266 0116, 0126 0196 0676 0666 0656 0646 0636 0256 0626 0616 0606 0596 0436 0416, 0426 0296 0386 0146, 0206 0016 0146 0106 0546 0536 0476 0446 0466 0456 0386  DBS TUNER Alpha Star Chaparral Echostar General Instrument HTS Hughes Network Systems Jerrold Panasonic Primestar RCA Sony 0826 0756 0836 0776 0836 0816 0776, 0786 0806 0776, 0786 0766 0796 VCR A Tandy 0902 Adventura 0992 Aiko 0982 Aiwa 0992 Akai 0262, 0942, 0952, 0962, 0972 American High 0932 Amstrad 0992 ASA 0002, 0912 Asha 0922 Audio Dynamics 0202 Audiovox 0912 Beaumark 0922 Bell & Howell 0902 Blaupunkt 0412 Broksonic 0872, 0882, 0892 Bush 0852 Calix 0912 Canon 0862, 0932 CCE 0852, 0982 Citizen 0912, 0982 Colt 0852 Craig 0832, 0842, 0852, 0912, 0922 Curtis Mathes 0662, 0822, 0932 Cybernex 0922 Daewoo 0802, 0812, 0982 DBX 0202 Dynatech 0472, 0992 Electrohome 0912 Electrophonic 0912 Emerex 0792 Emerson 0072, 0132, 0142, 0152, 0162, 0172, 0182, 0192, 0212, 0702, 0712, 0722, 0732, 0742, 0752, 0762, 0772, 0782, 0872, 0882, 0892, 0912, 0952, 0992, 1072 Finlux 0002, 0992 Fisher 0682, 0692, 0842, 0902 Fuji 0672, 0932 Funai 0992 Garrard 0992 GE 0662, 0822, 0932 Go Video 0642, 0652 GoldStar 0082, 0632, 0912 Goodmans 0402 Gradiente 0992 Granda 0612, 0902 Grundig 0002 H/K 1082 Harley Davidson 0992 Harmon/Kardon 0632, 1082 Harwood 0752, 0852 Headquarter 0612 HI-Q 0842 Hinari Hitachi 0852 0102, 0562, 0572, 0582, 0592, 0602, 0992 ITT 0942 JVC 0202, 0522, 0532, 0542, 0552 Kenwood 0202, 0542, 0612, 0632, 0902 KLH 0852 Kodak 0912, 0932 Lloyd 0992 Logik 0852 Luxor 0942 LXI 0022, 0912 Magnavox 0002, 0482, 0492, 0502, 0512, 0932 Magnin 0922 Marantz 0002, 0202, 0402, 0632, 0932 Marta 0912 Matsui 0722 Matsushita 0932 MEI 0222, 0932 Memorex 0232, 0242, 0472, 0512, 0612, 0842, 0902, 0912, 0922, 0932, 0992 MGA 0762, 0952 MGA Technology 0922 Minolta 0592, 0602 Mitsubishi 0452, 0462, 0542, 0762, 0952, 1082 Motorola 0472, 0932 MTC 0922, 0992 Multitech 0852, 0992 NAD 0442 NEC 0122, 0202, 0292, 0422, 0432, 0542, 0632 Nikko 0912 Noblex 0922 Olympus 0412, 0932 Optimus 0442, 0472, 0912 Optonica 0402 Orion 0212, 0722, 0742, 0772 Osaki 0912 Panasonic 0012, 0052, 0092, 0222, 0372, 0382, 0392, 0412, 0932 Penny 0202, 0432, 0602, 0632, 0692, 0912, 0922, 0932 Pentax 0592, 0602 Perdio 0992 Philco 0002, 0932 Philips 0002, 0282, 0402, 0492, 0932 Pilot 0912 Pioneer 0442, 0542 Proscan 1002, 1012, 1022, 1032, 1042, 1052, 1062 Pulsar 0512 Quarter 0612 Français 0036, 0216, 0306, 0316, 0326, 0336, 0346 Pioneer 0006, 0086 Pioneer BR50 0846 Pioneer BR60/70/80/81/82 0696 Pioneer BR90 0556 Pulsar 0386 RCA Digital Satellite System 0396, 0406 Realistic 0136 Regency/Eastern 0686 Runco 0386 Samsung 0276 Scientific Atlanta 175/475 0576 Scientific Atlanta 75 0366, 0586 Scientific Atlanta 8650 0566 Signal 0276 SL Marx 0276 Spectavision 0236 Standard Components 0186 Starcom V 0256 Stargate 0276 Sylvania/Texscan 0376, 0496 Teknika 0176 Teleservice 0056 Teleview 0276 Texscan 0186, 0376 TFC 0026 Tocom 0226, 0356 Tocom 5503A 0526 Tocom 5503VIP/5507 0516 Tocom TC56 0506 Toshiba 0386 Tudi 0046 Unika 0136 Universal 0136, 0156, 0206, 0286 Videoway 0096 Viewstar 0216 Zenith 0246, 0386, 0486 English Philips 89  Quartz 0272, 0612 Quasar 0382, 0392, 0932 Radio Shack 0912, 0992 Radix 0912 Randex 0912 RCA 0112, 0382, 0392, 0482, 0592, 0602, 0662, 0822, 0942 Realistic 0402, 0472, 0612, 0682, 0842, 0902, 0912, 0922, 0932, 0992 Ricoh 0352, 0362 Saisho 0212, 0582, 0722, 0732, 0742, 0772 Salora 0612, 0762 Samsung 0212, 0312, 0922, 0962 Sanky 0472, 0512 Sansui 0292, 0542, 0832 Sanyo 0242, 0612, 0842, 0902, 0922 SBR 0002, 0282 Schneider 0852 Scott 0342, 0712, 0762, 0872, 0882, 0892 Sears 0302, 0592, 0602, 0612, 0682, 0692, 0842, 0902, 0912, 0932 Sharp 0402, 0472 Shintom 0852 Shogun 0922 Singer 0852 Sony 0032, 0332, 0352, 0362, 0672, 0792, 0932 STS 0602 Sunpak 0352 Sylvania 0002, 0492, 0502, 0762, 0932, 0992 Symphonic 0992 Tandy 0992 Tashiko 0712, 0992 Teac 0992 Technics 0932 Teknika 0322, 0912, 0932, 0992 Telefunken 0252 TMK 0212, 0732, 0772, 0922 Toshiba 0062, 0302, 0342, 0622, 0682, 0712, 0762 Totevision 0912, 0922 Unitech 0922 Vector Research 0202, 0432, 0632 Victor 0532, 0542, 0552 Video Concepts 0202, 0432, 0632, 0952 Wards 0322, 0402, 0472, 0482, 0602, 0712, 0842, 0852, 0922, 0932, 0992 Yamaha 0202, 0632, 0762 Zenith 0042, 0362, 0512, 0672 90 DVD PLAYER Akai JVC Onkyo Panasonic Philips Pioneer Samsung Sharp Sony Toshiba Yamaha 0108 0168 0128 0048 0188 0208, 0228 0148 0068 0028 0088 0008, 0048 LD PLAYER Aiwa Denon Disco Vision Funai Hitachi (E) Kenwood Magnavox Marantz Mitsubishi NAD Panasonic Philips Pioneer RCA Realistic Sharp Sony Victor Yamaha 0157 0147 0017 0157 0017 0087, 0107 0027 0027 0137 0137 0077, 0177 0027 0037, 0017, 0137 0167 0157 0127 0047, 0057, 0117 0097 0007 CD PLAYER Acoustic Research 1295 ADC 0025, 0065 Adcom 0205, 0255, 1015 ADS 0265 Aiwa 0295, 0945, 1035, 1055 Akai 0175, 0485, 0535 Alpine 1215, 1305 Audio-Technica 0545 BSR 0245, 0655, 0775 California Audio Lab 0055 Capetronic 1205 Carrera 0245 Carver 0285, 1135 Casio 0345 Crown 0185 Curtis Maths 0345 Denon 0275, 0875, 0885 Deual (E) 0505 Dynamic Bass (H) 0555 Emerson 0205, 0325, 1105 Eroica 1275 Fisher 0095, 0555, 0925, 1005 Garrard 0365 Genexxa 0305, 0325, 1105 GoldStar 1225, 1265, 1135, 1335 H/K 0105, 0175, 0465, 0995 Hitachi 0195, 0505, 0205, 0815 Inkel 0115, 0395 JVC 0315 Kenwood 0045, 0095, 0405, 0585, 0725, 0735, 0745, 0755, 0895 Kyocera 0025 Luxman 0075, 0425, 0675, 0705, 0715, 0985 Magnavox 0165, 0215, 0645, 0955 Marantz 0215, 0235, 0375, 0785, 1345 McIntosh 0355, 1085 MCS 0905, 1315 Memorex 0205, 0225, 0235, 0305, 0325, 1105 MGA 0135 Mission 0215 Mitsubishi 0135, 0445 MTC 1255 NAD 0035, 0615, 0685, 0695 Nakamichi 0125, 0435, 0515 NEC 0255, 0905, 0965 Nikko 0545, 1005 Onkyo 0155, 0455, 0495, 0805, 1155 Optimus 0225, 0245, 0555, 0595, 0845, 0855, 0865, 0895, 0935 Panasonic 0055, 0825, 1095, 1125 Penny 0905 Philips 0165, 0215 Pioneer 0305, 0935, 1045 Proton 0215, 1185 Quasar 0055 RCA 0205, 0915, 1115 Realistic 0205, 0225, 0235, 0325, 0555, 0845 Revox 1175 Rotel 0215 Saba Telecommander (E) 0505 SAE 0215 Samsung 1285 Sansui 0215, 0625, 0975, 1025, 1105 Sanyo 0145, 0555, 0635, 0765 Scott 0325, 1105 Sears 0345 Sharp 0235, 0665, 0895, 1065, 1075 Sherwood 0115, 0235, 0395, 0475 Siements Garrard 1245 Signature 0175 Sontec 1165  MD RECORDER Yamaha 0024 TAPE DECK Aiwa Akai Carver Denon Fisher Garrard JVC Kenwood Magnavox Marantz Mitsubishi Onkyo Optimus Philips Pioneer Revox Sansui Sharp Sherwood Sony Teac Technics Victor Wards Yamaha 0094, 0214, 0224 0184 0094 0304 0144 0194, 0204 0274, 0284, 0294 0124, 0134, 0154, 0234, 0244, 0264 0094 0094, 0344 0184 0364, 0374 0034, 0064, 0204, 0334 0094 0034, 0044, 0064 0354 0094, 0344 0264 0334 0054, 0084, 0324 0194, 0254 0074, 0314 0294 0034 0004, 0014 Français 0065, 0565, 0865, 1145 1235 0025 0215 0335 0305 1195 0235, 0335, 0385, 0525, 0795, 0835, 1355 Technics 0055, 0605, 1095 Techwood 1325 Telefunken (E) 0505 Thomson (E) 0505 Toshiba 0035, 0685 Vector Research 0065, 1135 Victor 0315 Wards 0175 Yamaha 0005, 0015, 0575, 1065 English Sony Staron STS Sylvania Symphonic Tandy Tangberg Teac 91  94 YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA Printed in Malaysia V338160