Yamaha RX-V493RDS El manual del propietario

Categoría
Reproductores de casete
Tipo
El manual del propietario

Este manual también es adecuado para

OWNER’S MANUAL
MODE D’EMPLOI
Natural Sound AV Receiver
Récepteur audiovisuel “Son Naturel”
RX-V493
RX-V393
Thank you for selecting this YAMAHA AV receiver.
Nous vous remercions d’avoir porté votre choix sur ce récepteur audiovisuel YAMAHA.
U C A
1 Read Instructions – All the safety and operating
instructions should be read before the unit is operated.
2 Retain Instructions – The safety and operating instructions
should be retained for future reference.
3 Heed Warnings – All warnings on the unit and in the
operating instructions should be adhered to.
4 Follow Instructions – All operating and other instructions
should be followed.
5 Water and Moisture – The unit should not be used near
water – for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming
pool, etc.
6 Carts and Stands – The unit should be used only with a
cart or stand that is recommended by the
manufacturer.
6A A unit and cart combination should be
moved with care. Quick stops, excessive
force, and uneven surfaces may cause
the unit and
cart combination to overturn.
7 Wall or Ceiling Mounting – The unit should be mounted to
a wall or ceiling only as recommended by the
manufacturer.
8 Ventilation – The unit should be situated so that its
location or position does not interfere with its proper
ventilation. For example, the unit should not be situated
on a bed, sofa, rug, or similar surface, that may block the
ventilation openings; or placed in a built-in installation,
such as a bookcase or cabinet that may impede the flow
of air through the ventilation openings.
9 Heat – The unit should be situated away from heat
sources such as radiators, stoves, or other appliances
that produce heat.
10 Power Sources – The unit should be connected to a
power supply only of the type described in the operating
instructions or as marked on the unit.
11 Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the unit.
12 Cleaning – The unit should be cleaned only as
recommended by the manufacturer.
13 Nonuse Periods – The power cord of the unit should be
unplugged from the outlet when left unused for a long
period of time.
14 Object and Liquid Entry – Care should be taken so that
objects do not fall into and liquids are not spilled into the
inside of the unit.
15 Damage Requiring Service – The unit should be serviced
by qualified service personnel when:
A. The power-supply cord or the plug has been
damaged; or
B. Objects have fallen, or liquid has been spilled into the
unit; or
C. The unit has been exposed to rain; or
D. The unit does not appear to operate normally or
exhibits a marked change in performance; or
E. The unit has been dropped, or the cabinet damaged.
16 Servicing – The user should not attempt to service the unit
beyond those means described in the operating
instructions. All other servicing should be referred to
qualified service personnel.
17 Power Lines – An outdoor antenna should be located
away from power lines.
18 Grounding or Polarization – Precautions should be taken
so that the grounding or polarization is not defeated.
SAFETY INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
Explanation of Graphical Symbols
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert you to the presence
of uninsulated “dangerous voltage”
within the product’s enclosure that may
be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
you to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
1
English
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
SPECIAL NOTES FOR FCC COMPOSITE
DEVICE (for US customers only)
This device is a composite system. The digital device
component may not cause harmful interference.
19 For US customers only:
Outdoor Antenna Grounding – If an outside antenna is
connected to this unit, be sure the antenna system is
grounded so as to provide some protection against
voltage surges and built-up static charges. Article 810 of
the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to
grounding electrodes, and requirements for the grounding
electrode.
EXAMPLE OF ANTENNA GROUNDING
MAST
GROUND
CLAMP
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)
GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
ELECTRIC
SERVICE
EQUIPMENT
NEC – NATIONAL ELECTRICAL CODE
1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product
MUST be used. Follow all installation instructions.
Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC Regulations,
Part 15 for Class “B” digital devices. Compliance with
these requirements provides a reasonable level of
assurance that your use of this product in a residential
environment will not result in harmful interference with
other electronic devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product
is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try
to eliminate the problem by using one of the following
measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
FCC INFORMATION (for US customers only)
YAMAHA and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the
sound come through loud and clear without annoying blaring
or distortion – and, most importantly, without affecting your
sensitive hearing.
Since hearing damage from loud sounds is often
undetectable until it is too late, YAMAHA and the
Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid
prolonged exposure from excessive volume levels.
We Want You Listening For A Lifetime (for US customers only)
2
Safety Instructions ..............Inside the Front Cover
Supplied Accessories .....................................2
Features .........................................................3
Caution ...........................................................4
Notes about the Remote Control Transmitter
.......................................................................5
Profile of This Unit ..........................................6
Speaker Setup ................................................7
Connections ...................................................8
Controls and Their Functions .......................16
Speaker Balance Adjustment .......................22
Basic Operations ..........................................25
Tuning Operations ........................................29
Preset Tuning ...............................................30
Using Digital Sound Field Processor (DSP)
.....................................................................33
Setting the SLEEP Timer .............................37
Troubleshooting ............................................38
Specifications ...............................................39
After unpacking, check that the following parts are included.
Indoor FM Antenna
AM Loop Antenna
Antenna adapter (U.S.A. and Canada models only)
Batteries (size AA, R6, UM-3)
Remote Control Transmitter
2CH
/6CH
REC/PAUSE
DIR BDIR A
PLAY
DISC
VOLUME
PLAY
PRESET
A/B/C/D/E
–+
TESTDELAY TIME
EFFECT
PROGRAM
PROLOGIC
ENHANCED
–+
SLEEP
TAPE
A/B
ON/OFF
TUNER
CD
PHONO
VIDEO
VCR
POWER /I
REC/PAUSE
DIR BDIR A
PLAY
DISC
POWER /I
VOLUME
PLAY
PRESET
A/B/C/D/E
–+
TIME/
LEVEL
TEST
EFFECT
PROGRAM
PROLOGIC
ENHANCED
–+
SLEEP
TAPE
A/B
ON/OFF
2CH
/6CH
TUNER
CD
PHONO
DELAY/CENTER
/REAR/SWFR
DVD/LD
VCR
TV/DBS
RX-V493 RX-V393
CONTENTS
SUPPLIED ACCESSORIES
3
English
5 Speaker Configuration
RX-V493
Main: <U.S.A. and Canada models>
70W + 70W (8) RMS Output
Power, 0.04% THD, 20–20,000 Hz
<Europe, Australia, China
and General models
>
65W + 65W (8) RMS Output
Power, 0.04% THD, 20–20,000 Hz
Center: <U.S.A. and Canada models>
70W (8) RMS Output Power,
0.04% THD, 1 kHz
<Europe, Australia, China
and General models
>
65W (8) RMS Output Power,
0.04% THD, 1 kHz
Rear: 20W + 20W (8) RMS Output
Power, 0.04% THD, 1 kHz
RX-V393
Main: 50W + 50W (8) RMS Output
Power, 0.04% THD, 20–20,000 Hz
Center: 50W (8) RMS Output
Power, 0.04% THD, 1 kHz
Rear: 20W + 20W (8) RMS Output
Power, 0.04% THD, 1 kHz
Digital Sound Field Processor
Dolby Pro Logic Surround Decoder
Theater-like Sound Experience by the
Combination of Dolby Pro Logic and
YAMAHA DSP Technology (CINEMA DSP)
Automatic Input Balance Control for
Dolby Pro Logic Surround
Test Tone Generator for Easier Speaker
Balance Adjustment
3 Center Channel Modes
(NORMAL/WIDE/PHANTOM)
40-Station Random Access Preset Tuning
Automatic Preset Tuning
Preset Station Shifting Capability (Preset
Editing)
IF Count Direct PLL Synthesizer Tuning
System
6-Channel Discrete Input Terminals for
Connecting with a Dolby Digital (AC-3)
Decoder
Video Signal Input/Output Capability
SLEEP Timer
Remote Control Capability
FEATURES
4
1. To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2. Install this unit in a cool, dry, clean place – away from
windows, heat sources, sources of excessive vibration,
dust, moisture and cold. Avoid sources of humming
(transformers, motors). To prevent fire or electrical shock,
do not expose the unit to rain or water.
3. Never open the cabinet. If something drops into the set,
contact your dealer.
4. Do not use force on switches, controls or connection wires.
When moving the unit, first disconnect the power plug and
the wires connected to other equipment. Never pull the
wires themselves.
5. The openings on the cabinet assure proper ventilation of
the unit. If these openings are obstructed, the temperature
inside the cabinet will rise rapidly. Therefore, avoid placing
objects against these openings, and install the unit in well-
ventilated condition. Make sure to allow a space of at least
20 cm behind, 20 cm on the both sides and 30 cm above
the top panel of the unit. Otherwise it may not only damage
the unit, but also cause fire.
6. Always set the VOLUME control to “–
” before starting
the audio source play. Increase the volume gradually to an
appropriate level after playback has been started.
7. Do not attempt to clean the unit with chemical solvents;
this might damage the finish. Use a clean, dry cloth.
8. Be sure to read the “TROUBLESHOOTING” section
regarding common operating errors before concluding that
the unit is faulty.
9. When not planning to use this unit for long periods of time
(ie., vacation, etc.), disconnect the AC power plug from the
wall outlet.
10.To prevent lightning damage, disconnect the AC power
plug and disconnect the antenna cable when there is an
electrical storm.
11.Grounding or polarization – Precautions should be taken
so that the grounding or polarization of an appliance is not
defeated.
12.AC outlet
Do not connect audio equipment to the AC outlet on the
rear panel if that equipment requires more power than the
outlet is rated to provide.
13.Voltage Selector (China and General Models only)
The voltage selector on the rear panel of this unit must
be set for your local main voltage BEFORE plugging
into the AC main supply.
Voltages are 110/120/220/240 V AC, 50/60 Hz.
IMPORTANT
Please record the serial number of this unit in the space
below.
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
FOR CANADIAN CUSTOMERS
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE
OF PLUG TO WIDE SLOT AND FULLY INSERT.
THIS CLASS B DIGITAL APPARATUS MEETS ALL
REQUIREMENTS OF THE CANADIAN INTERFERENCE-
CAUSING EQUIPMENT REGULATIONS.
This unit is not disconnected from the AC power source as
long as it is connected to the wall outlet, even if this unit
itself is turned off. This state is called the standby mode.
In this state, this unit is designed to consume a very small
quantity of power.
WARNING
Do not change the IMPEDANCE SELECTOR switch
setting while the power to this unit is on, otherwise
this unit may be damaged.
IF THIS UNIT FAILS TO TURN ON WHEN THE
STANDBY/ON SWITCH IS PRESSED
The IMPEDANCE SELECTOR switch may not be set to
either end closely. If so, set the switch to either end
closely.
IMPEDANCE SELECTOR
(U.S.A. model)
REAR
CENTER
MAIN
6
MIN. /SPEAKER
SINGLE
:
6
MIN. /SPEAKER
DUAL
:3
MIN. /SPEAKER
A OR B
:4
MIN. /SPEAKER
A B
:8
MIN. /SPEAKER
REAR
CENTER
MAIN
8
MIN. /SPEAKER
SINGLE
:
8
MIN. /SPEAKER
DUAL
:4
MIN. /SPEAKER
A OR B
:8
MIN. /SPEAKER
A B
:16
MIN. /SPEAKER
IMPEDANCE SELECTOR
SET BEFORE POWER ON
CAUTION : READ THIS BEFORE OPERATING YOUR UNIT.
FREQUENCY STEP switch (China and General Models
only)
Because the interstation frequency spacing differs in
different areas, set the FREQUENCY STEP switch (located
at the rear) according to the frequency spacing in your area.
Before setting this switch, disconnect the AC power plug of
this unit from the AC outlet.
5
English
Battery installation
Battery replacement
If you find that the remote control transmitter must be used
closer to the main unit, the batteries are weak. Replace both
batteries with new ones.
Notes
Use only AA, R6, UM-3 batteries for replacement.
Be sure the polarities are correct. (See the illustration inside
the battery compartment.)
Remove the batteries if the remote control transmitter will not
be used for an extended period of time.
If batteries leak, dispose of them immediately. Avoid
touching the leaked material or letting it come in contact with
clothing, etc. Clean the battery compartment thoroughly
before installing new batteries.
Remote control transmitter operation range
Notes
There should be no large obstacles between the remote
control transmitter and the main unit.
If the remote control sensor is directly illuminated by strong
lighting (especially an inverter type of fluorescent lamp etc.),
it might cause the remote control transmitter not to work
correctly. In this case, reposition the main unit to avoid direct
lighting.
1
3
2
l6
20
28
40
60
l2
8
4
2
0
–dB
l6
20
28
40
60
l2
8
4
2
0
–dB
30°
30°
Remote control
sensor
Within approximately
6 m (19.7 feet)
RX-V393
RX-V493
NOTES ABOUT THE REMOTE CONTROL TRANSMITTER
6
PROFILE OF THIS UNIT
You are the proud owner of a Yamaha stereo receiver –an extremely sophisticated audio component. The Digital Sound Field
Processor (DSP) built into this unit takes advantage of Yamaha’s undisputed leadership in the field of digital audio processing to
bring you a whole new world of listening experiences. Follow the instructions in this manual carefully when setting up your system,
and this unit will sonically transform your room into a wide range of listening environments –movie theater, concert hall, and so on.
In addition, you get incredible realism from sources encoded with Dolby Surround using the built-in Dolby Pro Logic Surround
Decoder.
Please read this operation manual carefully and store it in a safe place for later reference.
Digital Sound Field Processing
What is it that makes live music so good? Today’s advanced
sound reproduction technology lets you get extremely close to
the sound of a live performance, but chances are you’ll still
notice something missing: the acoustic environment of the live
concert hall. Extensive research into the exact nature of the
sonic reflections that create the ambience of a large hall has
made it possible for Yamaha engineers to bring you this same
sound in your own listening room, so you’ll feel all the sound of
a live concert.
Furthermore, our technicians, armed with sophisticated
measuring equipment, have even made it possible to capture
the acoustics of a variety of venues such as an actual concert
hall, theater, etc. to allow you to accurately recreate one of
several actual live performance environments, all in your own
home.
Dolby Pro Logic Surround
This unit employs a Dolby Pro Logic Surround decoder similar
to professional Dolby Stereo decoders used in many movie
theaters. By using the Dolby Pro Logic Surround decoder, you
can experience the dramatic realism and impact of Dolby
Surround movie theater sound in your own home. Dolby Pro
Logic employs a four channel five speaker system. The Pro
Logic Surround system divides the input signal into four levels:
the left and right main channels, the center channel (used for
dialog), and the rear surround sound channels (used for sound
effects, background noise, and other ambient noises). The
center channel allows listeners seated in even less-than-ideal
positions to hear the dialog originating from the action on the
screen while experiencing good stereo imaging.
Dolby Surround is encoded on the sound track of pre-recorded
video tapes, laser discs, and some TV/cable broadcasts. When
you play a source encoded with Dolby Surround on this unit,
the Dolby Pro Logic Surround decoder decodes the signal and
distributes the surround-sound effects.
This Dolby Pro Logic Surround Decoder employs a digital
signal processing system. This system improves the stability of
sound at each channel and minimizes crosstalk between
channels, so that positioning of sounds around the room is
more accurate compared with conventional analog signal
processing systems.
In addition, this unit features a built-in automatic input balance
control. This always assures you the best performance without
manual adjustment.
Manufactured under license from Dolby Laboratories Licensing
Corporation. “Dolby”, “AC-3”, “Pro Logic” and the double-D
symbol are trademarks of Dolby Laboratories Licensing
Corporation.
Dolby Pro Logic Surround + DSP
Dolby Surround sound system shows its full ability in a large
movie theater, because movie sounds are originally designed
to be reproduced in a large movie theater using many
speakers. It is difficult to create a sound environment similar to
that of a movie theater in your listening room, because the
room size, materials of inside walls, the number of speakers,
etc. of your listening room is much different from those of a
movie theater.
Yamaha DSP technology made it possible to present you with
nearly the same sound experience as that of a large movie
theater in your listening room by compensating for lack of
presence and dynamics in your listening room with its original
digital sound fields combined with Dolby Surround sound field.
The combination of Dolby Pro Logic Surround and DSP is used
on the sound field program “ PRO LOGIC ENHANCED”.
The YAMAHA “CINEMA DSP” logo indicates these programs are
created by the combination of Dolby Pro Logic and YAMAHA
DSP technology.
CINEMA DSP
7
English
SPEAKER SETUP
SPEAKERS TO BE USED
This unit is designed to provide the best sound-field quality with a 5 speaker configuration. The most effective speakers to use with
this unit are main speakers, rear speakers and a center speaker. You may omit the center speaker. (Refer to the “4-Speaker
Configuration” shown below.)
The main speakers are used for the main source sound plus the effect sounds. They will probably be the speakers from your
present stereo system. The rear speakers are used for the effect and surround sounds, and the center speaker is for the center
sounds (dialog etc.) within programs encoded with Dolby Surround. The center speaker needs to be equal in power to the main
speakers, although the rear speakers should not be equal. However, all the speakers should have high enough power handling to
accept the maximum output of this unit.
SPEAKER CONFIGURATION
5-Speaker Configuration
This configuration is the most effective and recommended one.
In this configuration, the center speaker is necessary as well as
the rear speakers. If the program DOLBY PRO LOGIC or
DOLBY PRO LOGIC ENHANCED is selected, conversations
will be output from the center speaker and the ambience will be
excellent.
Set the center channel mode to the “NORMAL” or “WIDE
position. (For details, refer to page 23.)
4-Speaker Configuration
The center speaker is not used in this configuration. If the
program DOLBY PRO LOGIC or DOLBY PRO LOGIC
ENHANCED is selected, the center sound is output from the
left and the right main speakers. However, the sound effect of
other programs can be the same as that of the 5-speaker
configuration.
Be sure to set the center channel mode to the “PHANTOM
position. (For details, refer to page 23.)
SPEAKER PLACEMENT
The recommended speaker configuration, the 5-speaker configuration, will require two speaker pairs: main speakers (your normal
stereo speakers), and rear speakers, plus a center speaker. When you place these speakers, refer to the following.
Main: In normal position. (The position of your present
stereo speaker system.)
Rear: Behind your listening position, facing slightly inward.
Nearly 1.8m (approx. 6 feet) up from the floor.
Center: Precisely between the main speakers. (To avoid
interference with TV sets, use a magnetically shielded
speaker.)
Front R
Center
Front L
TV set
Rear R
Rear L
Main L
Main R
Main L
Main R
Main L
Main R
8
CONNECTIONS
Never plug in this unit and other components until all connections are completed.
CONNECTIONS WITH OTHER COMPONENTS
When making connections between this unit and other components, be sure all connections are made correctly, that is to say L (left)
to L, R (right) to R, “+” to “+” and “” to “”. Also, refer to the owner’s manual for each component to be connected to this unit.
* If you have YAMAHA components numbered as 1, 2, 3, etc. on the rear panel, connections can be made easily by making sure
to connect the output (or input) terminals of each component to the same-numbered terminals of this unit.
*
1
,
*
2
: See the next page.
FM
ANT
AM
ANT
GND
75
UNBAL.
GND
MONITOR OUT
DVD/LD TV/DBS
IN OUT
VCR
IN OUT
VCR
PHONO
CD
DVD/LD TV/DBS
TAPE
PB
REC
OUT
1
3 4
REAR
CENTER
MAIN
6
MIN. /SPEAKER
SINGLE
:
6
MIN. /SPEAKER
DUAL
:3
MIN. /SPEAKER
A OR B
:4
MIN. /SPEAKER
A B
:8
MIN. /SPEAKER
REAR
CENTER
MAIN
8
MIN. /SPEAKER
SINGLE
:
8
MIN. /SPEAKER
DUAL
:4
MIN. /SPEAKER
A OR B
:8
MIN. /SPEAKER
A B
:16
MIN. /SPEAKER
DVD/LD
TV/DBS
MAIN
R L
SURROUND
R L
CENTER
SUB
WOOFER
6CH
DISCRETE
INPUT
VIDEO
SIGNAL
TAPE
/MD
AUDIO SIGNAL
IMPEDANCE SELECTOR
SET BEFORE POWER ON
SEE INSTRUCTION MANUAL FOR CORRECT SETTING
.
MAIN
A
B
CENTER
REAR
(SURROUND)
OUTPUT
SUB
WOOFER
SPEAKERS
GND
OUTPUT
AUDIO IN
VIDEO IN
AUDIO OUT
VIDEO OUT
VIDEO IN
AUDIO OUT
VIDEO OUT
LINE OUT
LINE IN
OUTPUT
VIDEO OUT
AUDIO OUT
I20V 60Hz
I00W MAX. TOTAL
SWITCHED
AC OUTLETS
(U.S.A. model)
To AC outlet
Turntable
LD player,
DVD player, etc.
Video cassette recorder
TV/Satellite tuner
Tape deck,
MD recorder, etc.
CD player
Monitor TV
*
2
*
1
RX-V493
9
English
AC OUTLET(S) (SWITCHED)
Except Australia model.......................2 SWITCHED OUTLETS
Australia model.....................................1 SWITCHED OUTLET
Use these to connect the power cords from your components
to this unit.
The power to the SWITCHED outlets is controlled by this unit’s
STANDBY/ON switch or the provided remote control
transmitter’s POWER /I key. These outlets will supply power
to any component whenever this unit is turned on.
The maximum power (total power consumption of components)
that can be connected to the SWITCHED AC OUTLET(S) is
100 watts.
GND terminal (For turntable use)
Connecting the ground wire of the turntable to the GND
terminal will normally minimize hum, but in some cases better
results may be obtained with the ground wire disconnected.
*
1
*
2
RX-V393
FM
ANT
AM
ANT
GND
75
UNBAL.
GND
MONITOR OUT
VIDEO
IN OUT
VCR
IN OUT
VCR
PHONO
CD
VIDEO
TAPE
PB
REC
OUT
1
3 4
REAR
CENTER
MAIN
6
MIN. /SPEAKER
SINGLE
:
6
MIN. /SPEAKER
DUAL
:3
MIN. /SPEAKER
A OR B
:4
MIN. /SPEAKER
A B
:8
MIN. /SPEAKER
REAR
CENTER
MAIN
8
MIN. /SPEAKER
SINGLE
:
8
MIN. /SPEAKER
DUAL
:4
MIN. /SPEAKER
A OR B
:8
MIN. /SPEAKER
A B
:16
MIN. /SPEAKER
VIDEO
MAIN
R L
SURROUND
R L
CENTER
SUB
WOOFER
6CH
DISCRETE
INPUT
VIDEO
SIGNAL
TAPE
/MD
AUDIO SIGNAL
IMPEDANCE SELECTOR
SET BEFORE POWER ON
SEE INSTRUCTION MANUAL FOR CORRECT SETTING
.
MAIN
A
B
CENTER
REAR
(SURROUND)
OUTPUT
SUB
WOOFER
SPEAKERS
GND
OUTPUT
AUDIO IN
VIDEO IN
AUDIO OUT
VIDEO OUT
VIDEO IN
LINE OUT
LINE IN
OUTPUT
VIDEO OUT
AUDIO OUT
I20V 60Hz
I00W MAX. TOTAL
SWITCHED
AC OUTLETS
(U.S.A. model)
To AC outlet
Turntable
LD player,
DVD player, etc.
Video cassette recorder
Tape deck,
MD recorder, etc.
CD player
Monitor TV
*
2
*
1
*
1
,
*
2
: See below.
10
Connecting with a Dolby Digital (AC-3) Decoder
If you have a Dolby Digital (AC-3) Decoder unit or an LD player etc. which incorporates a Dolby Digital (AC-3) Decoder, its discrete
outputs can be connected to this unit.
Notes for RX-V493
The laserdisc player (or another unit) must be also
connected to the DVD/LD (or TV/DBS) AUDIO SIGNAL input
terminals of this unit for playing a source with the Dolby Pro
Logic Surround decoded or in normal stereo (or monaural).
The discrete signals input to this unit cannot be recorded by
a tape deck, MD recorder or VCR. To record a source played
on the laserdisc player (or another unit), it must be
connected to the DVD/LD (or TV/DBS) AUDIO/VIDEO
SIGNAL input terminals of this unit.
If you made no connection to the SUBWOOFER input
terminal of this unit or you will not use a subwoofer, you
should make a setting for distributing signals at the LFE
channel to the right and left MAIN output terminals on the
Dolby Digital (AC-3) Decoder unit.
For details, refer to the owner’s manual for the Dolby Digital
(AC-3) Decoder unit.
FM
ANT
AM
ANT
GND
75
UNBAL.
GND
MONITOR OUT
DVD/LD TV/DBS
IN OUT
VCR
IN OUT
VCR
PHONO
CD
DVD/LD TV/DBS
TAPE
PB
REC
OUT
1
3 4
DVD/LD
TV/DBS
MAIN
R L
SURROUND
R L
CENTER
SUB
WOOFER
6CH
DISCRETE
INPUT
VIDEO
SIGNAL
TAPE
/MD
AUDIO SIGNAL
AC-3 RF
OUT
AC-3 RF
IN
DIGITAL
IN
DIGITAL
OUT
VIDEO OUT
AUDIO OUT
6CH DISCRETE OUTPUT
CENTER SURROUNDMAIN
SUB
WOOFER
Dolby Digital (AC-3) Decoder unit
RF Demodulator
Laserdisc player with AC-3 RF output or
another unit with AC-3 RF output
RX-V493
11
English
Notes for RX-V393
The laserdisc player (or another unit) must be also
connected to the VIDEO AUDIO SIGNAL input terminals of
this unit for playing a source with the Dolby Pro Logic
Surround decoded or in normal stereo (or monaural).
The discrete signals input to this unit cannot be recorded by
a tape deck, MD recorder or VCR. To record a source played
on the laserdisc player (or another unit), it must be
connected to the VIDEO AUDIO/VIDEO SIGNAL input
terminals of this unit.
If you made no connection to the SUBWOOFER input
terminal of this unit or you will not use a subwoofer, you
should make a setting for distributing signals at the LFE
channel to the right and left MAIN output terminals on the
Dolby Digital (AC-3) Decoder unit.
For details, refer to the owner’s manual for the Dolby Digital
(AC-3) Decoder unit.
FM
ANT
AM
ANT
GND
75
UNBAL.
GND
MONITOR OUT
VIDEO
IN OUT
VCR
IN OUT
VCR
PHONO
CD
VIDEO
TAPE
PB
REC
OUT
1
3 4
VIDEO
MAIN
R L
SURROUND
R L
CENTER
SUB
WOOFER
6CH
DISCRETE
INPUT
VIDEO
SIGNAL
TAPE
/MD
AUDIO SIGNAL
AC-3 RF
OUT
AC-3 RF
IN
DIGITAL
IN
DIGITAL
OUT
VIDEO OUT
AUDIO OUT
6CH DISCRETE OUTPUT
CENTER SURROUNDMAIN
SUB
WOOFER
Dolby Digital (AC-3) Decoder unit
RF Demodulator
Laserdisc player with AC-3 RF output or
another unit with AC-3 RF output
RX-V393
12
CONNECTING SPEAKERS
CENTER
REAR
(SURROUND)
OUTPUT
SUB
WOOFER
REAR
CENTER
CD
DUAL
SINGLE
CAUTION
SEE INSTRUCTION MANUAL FOR CORRECT SETTING
.
MAIN
A
B
REAR
CENTER
MAIN
6
MIN. /SPEAKER
SINGLE
:
6
MIN. /SPEAKER
DUAL
:3
MIN. /SPEAKER
A OR B
:4
MIN. /SPEAKER
A B
:8
MIN. /SPEAKER
REAR
CENTER
MAIN
8
MIN. /SPEAKER
SINGLE
:
8
MIN. /SPEAKER
DUAL
:4
MIN. /SPEAKER
A OR B
:8
MIN. /SPEAKER
A B
:16
MIN. /SPEAKER
SPEAKERS
IMPEDANCE SELECTOR
SET BEFORE POWER ON
Rear speaker Rear speaker
Center speaker
Main speakers B
Left
Right
Left
Right
Main speakers A
Subwoofer system
Left
Right
Note
Use speakers with the specified impedance shown on the rear
of this unit.
Note on main speaker connections:
One or two speaker systems can be connected to this unit. If
you use only one speaker system, connect it to either the
SPEAKERS A or B terminals.
Note on a subwoofer connection:
You may wish to add a subwoofer to reinforce low frequencies
or to output low bass sound from the subwoofer channel when
reproducing discrete signals.
Connect the SUBWOOFER OUTPUT terminal of this unit to
the INPUT terminal of the subwoofer amplifier, and connect the
speaker terminals of the subwoofer amplifier to the subwoofer.
With some subwoofers, including the Yamaha Active Servo
Processing Subwoofer System, the amplifier and subwoofer
are in the same unit.
Note on center speaker connection:
One or two center speakers can be connected to this unit. If
you cannot place the center speaker on or under the TV, it is
recommended to use two center speakers and place them on
both sides of the TV to orient the center sound at the center
position. For connecting two center speakers, follow the
method shown below.
REAR
CENTER
CD
DUAL
SINGLE
Center speaker
Center speaker
(U.S.A. model)
<U.S.A., Canada, China and General models only>
Banana Plug connections are also possible. Simply insert the
Banana Plug connector into the corresponding terminal.
13
English
For connecting to the MAIN SPEAKERS terminals
Red: positive (+)
Black: negative (–)
Unscrew the knob.
Insert the bare wire.
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
Tighten the knob and
secure the wire.
For connecting to the REAR and CENTER SPEAKERS
terminals
Red: positive (+)
Black: negative (–)
Press the tab.
Insert the bare wire.
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
Release the tab and
secure the wire.
1
2
3
How to Connect:
Connect the SPEAKERS terminals to your speakers with wire of the proper gauge, cut as short as possible. If the connections are
faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is the + and –
markings are observed. If these wires are reversed, the sound will be unnatural and lack bass.
Caution
Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could damage
this unit and/or speakers.
14
CENTER OUTPUT terminal
This terminal is for center channel line output. There is no
connection to this terminal when you use the built-in amplifier.
However, if you drive a center speaker with an external power
amplifier, connect the input terminal of the external amplifier to
this terminal.
SUBWOOFER OUTPUT terminal
This terminal is for connecting with the input terminal of an
amplifier for driving a subwoofer.
When the input signals to this unit are in normal 2-channel
stereo, this terminal outputs only frequencies below 150 Hz
from the main and center channels. When discrete signals are
input to this unit and are selected as the input source, this
terminal outputs signals from the subwoofer channel.
REAR (SURROUND) OUTPUT terminals
These terminals are for rear channel line output. There is no
connection to these terminals when you use the built-in
amplifier.
However, if you drive rear speakers with an external stereo
power amplifier, connect the input terminals of the external
amplifier (MAIN IN or AUX terminals of a power amplifier or an
integrated amplifier) to these terminals.
Note
Output level of signals from these terminals are adjusted
by the use of VOLUME control on the front panel or VOLUME
keys on the remote control transmitter.
OUTPUT terminals (for driving speakers with external amplifiers)
Be sure to switch this only when the power to this unit is not on.
Select the position whose requirements your speaker system
meets.
(Upper position)
Rear: The impedance of each speaker must be 6or
higher.
Center: If you use one center speaker, the impedance of the
speaker must be 6or higher.
If you use two center speakers, the impedance of
each speaker must be 3or higher.
Main: If you use one pair of main speakers, the impedance
of each speaker must be 4or higher.
If you use two pairs of main speakers, the impedance
of each speaker must be 8or higher.
(Lower position)
Rear: The impedance of each speaker must be 8or
higher.
Center: If you use one center speaker, the impedance of the
speaker must be 8or higher.
If you use two center speakers, the impedance of
each speaker must be 4or higher.
Main:
<Except Canada model>
If you use one pair of main speakers, the impedance
of each speaker must be 8or higher.
If you use two pairs of main speakers, the
impedance of each speaker must be 16or higher.
<For Canada model only>
The impedance of each speaker must be 8or
higher.
IMPEDANCE SELECTOR switch
REAR
CENTER
MAIN
6
MIN. /SPEAKER
SINGLE
:
6
MIN. /SPEAKER
DUAL
:3
MIN. /SPEAKER
A OR B
:4
MIN. /SPEAKER
A B
:8
MIN. /SPEAKER
REAR
CENTER
MAIN
8
MIN. /SPEAKER
SINGLE
:
8
MIN. /SPEAKER
DUAL
:4
MIN. /SPEAKER
A OR B
:8
MIN. /SPEAKER
A B
:16
MIN. /SPEAKER
IMPEDANCE SELECTOR
SET BEFORE POWER ON
CENTER
REAR
(SURROUND)
OUTPUT
SUB
WOOFER
(U.S.A. model)
WARNING
Do not change the IMPEDANCE SELECTOR switch
setting while the power to this unit is on, otherwise
this unit may be damaged.
IF THIS UNIT FAILS TO TURN ON WHEN THE
STANDBY/ON SWITCH IS PRESSED
The IMPEDANCE SELECTOR switch may not be set to
either end closely. If so, set the switch to either end
closely.
15
English
ANTENNA CONNECTIONS
Each antenna should be connected to the designated terminals correctly, referring to the following diagram.
Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal
strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience
poor reception quality, an outdoor antenna may result in improvement.
Connecting the AM loop antenna
* The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall.
* The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit.
GND terminal
For maximum safety and minimum interference, connect the
GND terminal to a good earth ground. A good earth ground is
a metal stake driven into moist earth.
Notes
When connecting the indoor
FM antenna, insert its
connector into the FM ANT
terminal firmly.
If you need an outdoor
FM antenna to improve
FM reception quality, either
300-ohm feeder or coaxial cable may be used. In locations
troubled by electrical interference, coaxial cable is
preferable.
FM
ANT
AM
ANT
GND
75
UNBAL.
Orient so that the best
reception is obtained.
1 2 3
Outdoor FM antenna
Outdoor AM antenna
AM loop
antenna
(included)
Ground
75-ohm/300-ohm
antenna adapter
75-ohm/300-ohm
antenna adapter
75-ohm coaxial cable
300-ohm feeder
Indoor FM
antenna
(included)
16
CONTROLS AND THEIR FUNCTIONS
FRONT PANEL
PRO LOGIC
ENHANCED
CONCERT
VIDEO
MONO
MOVIE
STADIUM
STANDBY/ON
NATURAL SOUND AV RECEIVER
RX–V493
SPEAKERSPHONES
A
ON
B
OFF
BASS TREBLE BALANCE
VOLUME
55
4
3
2
l
0
l
2
3
4
55
4
3
2
l
0
l
2
3
4
LR
l6
20
28
40
60
l2
8
4
2
0
–dB
CINEMA DSP
55
4
3
2
l
0
l
2
3
4
DELAY/CENTER
/REAR/SWFR
FM
/
AM
MAN'L
/
AUTO FM
TUNING
MODE
AUTO
/
MAN'L MONO
CENTER
MODE
DISCO
CONCERT
HALL
ROCK
CONCERT
EFFECT
DOWN
TUNING
UP
MEMORY
EDIT
TIME
/
LEVEL
A
/
B
/
C
/
D
/
E
1
2 3 4 5 6 7 8
VCR DVD
/
LDTV
/
DBS
TAPE/MD MON 2CH/6CH
TUNER
CD
PHONO
1
89 0 A B C EFH IJ
D
G
23 45 7
6
STANDBY/ON
NATURAL SOUND AV RECEIVER
RX–V393
SPEAKERSPHONES
A
ON
B
OFF
BASS TREBLE BALANCE
VOLUME
55
4
3
2
l
0
l
2
3
4
55
4
3
2
l
0
l
2
3
4
LR
l6
20
28
40
60
l2
8
4
2
0
–dB
CINEMA DSP
55
4
3
2
l
0
l
2
3
4
FM
/
AM
MAN'L
/
AUTO FM
TUNING
MODE
AUTO
/
MAN'L MONO
CENTER
MODE
DOWN
TUNING
UP
EFFECT
MEMORY
EDIT
PROGRAM
A
/
B
/
C
/
D
/
E
1
2 3 4 5 6 7 8
TAPE/MD
MONITOR
VIDEO
2CH/6CH
VCR
TUNER
CD
PHONO
REAR
LEVEL
CENTER
LEVEL
0l0 0l0
1
89 0 A B C EFH K
L MJ
D
6G
23 4 7
RX-V493
RX-V393
17
English
1 STANDBY/ON switch
Press this switch to turn the power to this unit on. Press it
again to turn this unit into the standby mode.
Standby mode
In this state, this unit consumes a very small quantity of
power to receive infrared-signals from the remote control
transmitter.
2 Remote control sensor
Receives signals from the remote control transmitter.
3 Display panel
Shows various information. (For details, refer to page 19.)
4 Input selector buttons
Select a program source to listen to or watch. When a button is
pressed, the name of selected source appears on the display.
RX-V493 only
When the TV/DBS or DVD/LD input source is selected,
pressing the same button (TV/DBS or DVD/LD) switches the
input signals between 2 channel stereo signals and 6 channel
discrete signals. When switched to “6ch”, discrete signals from
the unit connected to the 6CH DISCRETE INPUT DVD/LD
TV/DBS terminals of this unit are selected as the input signals.
RX-V393 only
When the VIDEO input source is selected, pressing the same
button (VIDEO) switches the input signals between 2 channel
stereo signals and 6 channel discrete signals. When switched
to “6ch”, discrete signals from the unit connected to the 6CH
DISCRETE INPUT VIDEO terminals of this unit are selected as
the input signals.
5 DSP program selector buttons
RX-V493 only
Select a DSP program. When a button is pressed, the name of
selected program lights up on the display.
6 EFFECT button
Switches on/off the digital sound field processor (including the
Dolby Pro Logic Surround decoder).
7 VOLUME control
Used to raise or lower the volume level.
8 PHONES jack
When you listen with headphones, connect the headphones to
the PHONES jack. You can listen to the sound to be output
from the main speakers through headphones.
When listening with headphones privately, set both the
SPEAKERS A and B switches to the OFF position and switch
off the digital sound field processor (so that no DSP program
name is illuminated on the display) by pressing the EFFECT
button.
9 SPEAKERS switches
Set the switch A or B (or both A and B) for the main speaker
system (connected to this unit) you will use to the ON position.
Set the switch for the main speaker system you will not use to
the OFF position.
0 A/B/C/D/E button
Press this button to select a desired group (A–E) of preset
stations.
A Preset station number selector buttons
Select a preset station number (1 to 8).
B Tone controls
These controls are effective only for the sound from the main
speakers.
BASS
Used to increase or decrease the low frequency response.
The 0 position produces flat response.
TREBLE
Used to increase or decrease the high frequency response.
The 0 position produces flat response.
C BALANCE control
Adjusts the balance of the output volume to the left and right
speakers to compensate for sound imbalance caused by
speaker location or listening room conditions.
D FM/AM button
Press this button to switch the reception band to FM or AM.
PHONES
18
E MEMORY (MAN’L/AUTO FM) button
When this button is pressed, the
MEMORY” indicator flashes
for about 5 seconds. During this period, select a desired
preset station number by pressing the corresponding preset
station number selector button to enter the displayed station
into the memory.
When this button is pressed and held for about 3 seconds, the
automatic preset tuning begins. (For details, refer to page 31.)
F EDIT button
This button is used to exchange the places of two preset
stations with each other.
G TUNING DOWN/UP button
Used for tuning. Press the “UP” side to tune in to higher
frequencies, and press the “DOWN” side to tune in to lower
frequencies.
H TUNING MODE (AUTO/MAN’L MONO) button
Press this button to switch the tuning mode to automatic or
manual. To select the automatic tuning mode, press this
button so that the “AUTO” indicator lights up on the display. To
select the manual tuning mode, press this button so that the
“AUTO” indicator goes off.
I DELAY/CENTER/REAR/SWFR and TIME/LEVEL +/–
buttons
RX-V493 only
Adjust the delay time (DELAY), the center channel output level
(CENTER), the rear channel output level (REAR) and the
output level to the SUBWOOFER OUTPUT terminal (SWFR).
Select the item which you want to adjust by pressing the
DELAY/CENTER/REAR/SWFR button and adjust its time or
level by pressing the TIME/LEVEL +/– button.
J CENTER MODE button
Selects a center channel output mode (NORMAL, WIDE or
PHANTOM). (For details, refer to page 23.)
K PROGRAM selector button
RX-V393 only
When the built-in digital sound field processor (including the
Dolby Pro Logic Surround decoder) is on, this button changes
the currently selected DSP program whenever the right or left
side of this button is pressed.
L CENTER LEVEL control
RX-V393 only
Adjusts the sound output level of the center speaker.
M REAR LEVEL control
RX-V393 only
Adjusts the sound output level of the rear speakers.
19
English
DISPLAY PANEL
PRESET
kHz
MHz
MEMORY
AUTO
SLEEP
TAPE MON
STEREO
0
20
l00
ms dB
PRO LOGIC
ENHANCED
CONCERT
VIDEO
MONO
MOVIE
STADIUM
DISCO
ROCK CONCERT
CONCERT HALL
NORM
WIDE
PHANTOM
EFFECT OFF
123
56
0978
4
1 Multi-information display
Displays various information, for example station frequency,
preset station number and name of selected input source.
2 STEREO indicator
Lights up when an FM stereo broadcast with sufficient signal
strength is received.
3 Signal-level meter
Indicates the signal level of the received station.
If multipath interference is detected, the indication decreases.
4 SLEEP indicator
Lights up while the built-in SLEEP timer is functioning.
5 Center channel mode indicators
The name of a selected center channel mode lights up only
when a program which uses the Dolby Pro Logic Surround
decoder is selected.
6 EFFECT OFF indicator
Lights up if neither the digital sound field processor nor the
Dolby Pro Logic Surround decoder is on. In this state, sound
output is 2-channel stereo.
7 MEMORY indicator
When the MEMORY button is pressed, this indicator flashes
for about 5 seconds. During this period, the displayed station
can be programmed to the memory by using the A/B/C/D/E
button and the preset station number selector buttons.
8 AUTO indicator
Lights up when this unit is in the automatic tuning mode.
9 TAPE MON indicator
Lights up when the tape deck (or MD recorder etc.) is selected
as the input source by pressing the TAPE/MD MONITOR
(MON) button.
0 DSP program indicators
The name of a selected DSP program lights up when the built-
in digital sound field processor and/or the Dolby Pro Logic
Surround decoder is on.
20
REMOTE CONTROL TRANSMITTER
The remote control transmitter provided with this unit is designed to control all the most commonly used functions of this unit. If the
CD player and tape deck connected to this unit are YAMAHA components designed for remote control compatibility, then this
remote control transmitter will also control various functions of each component.
REC/PAUSE
DIR BDIR A
PLAY
DISC
POWER /I
VOLUME
PLAY
PRESET
A/B/C/D/E
–+
TIME/
LEVEL
TEST
EFFECT
PROGRAM
PROLOGIC
ENHANCED
–+
SLEEP
TAPE
A/B
ON/OFF
2CH
/6CH
TUNER
CD
PHONO
DELAY/CENTER
/REAR/SWFR
DVD/LD
VCR
TV/DBS
2
3
4
2
8
9
6
7
5
1
1
2CH
/6CH
REC/PAUSE
DIR BDIR A
PLAY
DISC
VOLUME
PLAY
PRESET
A/B/C/D/E
–+
TESTDELAY TIME
EFFECT
PROGRAM
PROLOGIC
ENHANCED
–+
SLEEP
TAPE
A/B
ON/OFF
TUNER
CD
PHONO
VIDEO
VCR
2
3
4
2
8
9
6
7
5
1
1
POWER /I
RX-V393
RX-V493
21
English
For Control of This Unit
1 DELAY/CENTER/REAR/SWFR and TIME/LEVEL +/–
keys
RX-V493 only
Adjust the delay time (DELAY), the center channel output level
(CENTER), the rear channel output level (REAR) and the
output level to the SUBWOOFER OUTPUT terminal (SWFR).
Select the item which you want to adjust by pressing the
DELAY/CENTER/REAR/SWFR key and adjust its time or level
by pressing the TIME/LEVEL +/– key.
(For details, refer to page 28, 35 and 36.)
DELAY TIME +/– key
RX-V393 only
Adjusts the delay time, or the time difference between the
begining of source sound and the begining of effect sound.
(For details, refer to page 36.)
2 Tuner keys
Controls tuner.
+: Selects higher preset station number.
: Selects lower preset station number.
A/B/C/D/E: Selects the group (A – E) of preset station
numbers.
3 SLEEP timer key
This key is used to turn the built-in SLEEP timer on and off,
and to set the SLEEP time. (For details, refer to page 37.)
4 POWER /I key
Turns the power to this unit on and turns this unit into the
standby mode alternately.
5 VOLUME +/– keys
Turns the volume level up/down.
6 Input selector keys
Selects input source.
RX-V493 only
When the TV/DBS or DVD/LD input source is selected,
pressing the same key (TV/DBS or DVD/LD) switches the input
signals between 2 channel stereo signals and 6 channel
discrete signals. When switched to “6ch”, discrete signals from
the unit connected to the 6CH DISCRETE INPUT DVD/LD
TV/DBS terminals of this unit are selected as the input signals.
RX-V393 only
When the VIDEO input source is selected, pressing the same
key (VIDEO) switches the input signals between 2 channel
stereo signals and 6 channel discrete signals. When switched
to “6ch”, discrete signals from the unit connected to the 6CH
DISCRETE INPUT VIDEO terminals of this unit are selected as
the input signals.
7 Program selector keys
PROGRAM:
When the built-in digital sound field processor (including the
Dolby Pro Logic Surround decoder) is on, this key changes the
currently selected DSP program whenever the right or left side
of this key is pressed.
PROLOGIC:
Directly selects the PRO LOGIC program.
ENHANCED:
Directly selects the PRO LOGIC ENHANCED program.
8 EFFECT ON/OFF key
Switches on/off the digital sound field processor (including the
Dolby Pro Logic Surround decoder).
9 TEST key
Used for speaker balance adjustment. (For details, refer to
page 22–24.)
For Other Component Control
Identify the remote control transmitter keys with your
component’s keys. If these keys are identical, their functions
will be the same. On each key function, refer to the
corresponding instruction on your component’s manual.
1 Tape deck keys
Controls tape deck.
* DIR A, B and A/B are applicable only to double
cassette tape deck.
* For a single cassette deck with automatic reverse
function, pressing DIR A will reverse the direction of
tape running.
2 CD player keys
Controls compact disc player.
* DISC is applicable only to compact disc changer.
REC/PAUSE
DIR BDIR A
PLAY
DISC
POWER /I
VOLUME
PLAY
PRESET
A/B/C/D/E
–+
TIME/
LEVEL
TEST
EFFECT
PROGRAM
PROLOGIC
ENHANCED
–+
SLEEP
TAPE
A/B
ON/OFF
2CH
/6CH
TUNER
CD
PHONO
DELAY/CENTER
/REAR/SWFR
DVD/LD
VCR
TV/DBS
22
1
Set to the “
” position.
2 Turn the power on.
3 Select the main speakers to be used.
* If you use two main speaker systems, press both the A
and B switches.
4
Set to the “0” position.
5
SPEAKER BALANCE ADJUSTMENT
This procedure lets you adjust the sound output level balance between the main, center, and rear speakers using the built-in test
tone generator. When this adjustment is performed, the sound output level heard at the listening position will be the same from
each speaker. This is important for the best performance of the digital sound field processor and the Dolby Pro Logic Surround
decoder.
SPEAKERS
A
ON
OFF
B
BASS TREBLE
55
4
3
2
l
0
l
2
3
4
55
4
3
2
l
0
l
2
3
4
BALANCE
55
4
3
2
l
0
l
2
3
4
LR
l6
20
28
40
60
l2
8
4
2
0
–dB
VOLUME
STANDBY/ON
2CH
/6CH
REC/PAUSE
DIR BDIR A
PLAY
DISC
VOLUME
PLAY
PRESET
A/B/C/D/E
–+
TESTDELAY TIME
EFFECT
PROGRAM
PROLOGIC
ENHANCED
–+
SLEEP
TAPE
A/B
ON/OFF
TUNER
CD
PHONO
VIDEO
VCR
POWER /I
1
2
3
l6
20
28
40
60
l2
8
4
2
0
–dB
RX-V393
RX-V493
4
5
5
TEST
23
English
l6
20
28
40
60
l2
8
4
2
0
–dB
6 Select the center channel output mode suitable for your
speaker configuration.
(Refer to “SPEAKER CONFIGURATION” on page 7.)
On the feature of each mode, refer to the “Note” shown
below.
Note
In step 6, when you select a center channel output mode, note
the following.
For 5 speaker configuration)
NORMAL: Select this mode when you use a center speaker
that is smaller than the main speakers. In this
mode, the bass tone will be output from the main
speakers.
WIDE: Select this mode when you use the center speaker
approximately same sized as the main speakers.
For 4 speaker configuration)
PHANTOM: Select this mode when you do not use the center
speaker. The center sound will be output from the
left and right main speakers.
7 Turn up the volume.
You will hear a test tone (like pink noise) from the left main
speaker, then the center speaker, then the right main
speaker, and then the rear speakers, for about two seconds
each. The display changes as shown below.
* The test tone from the left rear speaker and the right
rear speaker will be heard at the same time.
8 Adjust the BALANCE control so that the effect sound
output level of the left main speaker and the right main
speaker are the same.
l6
20
28
40
60
l2
8
4
2
0
–dB
VOLUME
CENTER
MODE
NORMAL
WIDE
PHANTOM
6
8
7
BALANCE
55
4
3
2
l
0
l
2
3
4
LR
2CH
/6CH
REC/PAUSE
DIR BDIR A
PLAY
DISC
VOLUME
PLAY
PRESET
A/B/C/D/E
–+
TESTDELAY TIME
EFFECT
PROGRAM
PROLOGIC
ENHANCED
–+
SLEEP
TAPE
A/B
ON/OFF
TUNER
CD
PHONO
VIDEO
VCR
POWER /I
RX-V393
RX-V493
REC/PAUSE
DIR BDIR A
PLAY
DISC
POWER /I
VOLUME
PLAY
PRESET
A/B/C/D/E
–+
TIME/
LEVEL
TEST
EFFECT
PROGRAM
PROLOGIC
ENHANCED
–+
SLEEP
TAPE
A/B
ON/OFF
2CH
/6CH
TUNER
CD
PHONO
DELAY/CENTER
/REAR/SWFR
DVD/LD
VCR
TV/DBS
7 7
CONTINUED
Main (L)
Main (R)
Center
Rear (L and R)
9 Adjust the sound output levels of the center speaker and
the rear speakers so that they become almost as same
as that of the main speakers.
Make the adjustment of each speaker output level at your
listening position with the remote control transmitter.
a) Press once or more so that “CENTER” or “REAR”
appears on the display.
* Select “CENTER” to adjust the output level of the
center speaker, and select “REAR” to adjust the
output level of the rear speakers.
b) Adjust its level.
* Pressing the + side raises and the side lowers the
level.
10 Cancel the test tone.
Notes
Once you have completed these adjustments, you can
adjust whole sound level on your audio system by using
the VOLUME control (or the VOLUME keys on the remote
control transmitter) only.
If you use external power amplifiers, you may also use
their volume controls to achieve proper balance.
RX-V493 only
In step 9, if the center channel mode is in the
“PHANTOM” position, the sound output level of the center
speaker cannot be adjusted. This is because in this
mode, the center sound is automatically output from the
left and right main speakers.
24
2CH
/6CH
REC/PAUSE
DIR BDIR A
PLAY
DISC
VOLUME
PLAY
PRESET
A/B/C/D/E
–+
TESTDELAY TIME
EFFECT
PROGRAM
PROLOGIC
ENHANCED
–+
SLEEP
TAPE
A/B
ON/OFF
TUNER
CD
PHONO
VIDEO
VCR
POWER /I
RX-V393
RX-V493
REC/PAUSE
DIR BDIR A
PLAY
DISC
POWER /I
VOLUME
PLAY
PRESET
A/B/C/D/E
–+
TIME/
LEVEL
TEST
EFFECT
PROGRAM
PROLOGIC
ENHANCED
–+
SLEEP
TAPE
A/B
ON/OFF
2CH
/6CH
TUNER
CD
PHONO
DELAY/CENTER
/REAR/SWFR
DVD/LD
VCR
TV/DBS
10
10
9
RX-V393
TIME/
LEVEL
–+
RX-V493
DELAY/CENTER
/REAR/SWFR
Disappears.
TEST
CENTER
LEVEL
0l0
REAR
LEVEL
0l0
l6
20
28
40
60
l2
8
4
2
0
–dB
9
25
English
1
Set to the “
” position.
2 Turn the power on.
3 Select the desired input source by using the input
selector buttons.
(For video sources, turn the TV/monitor ON.)
* The name of the selected input source will appear on
the display.
4 Select the main speakers to be used.
* If you use two main speaker systems, press both the A
and B switches.
5 Play the source. (For detailed information on the
tuning operation, refer to page 29.)
6
Adjust to the desired output level.
7 If desired, adjust the BASS, TREBLE and BALANCE
controls (refer to page 28), and use the digital sound
field processor. (Refer to page 34.)
Notes on using the input selector buttons
Note that pressing on each input selector button selects
the source which is connected to the corresponding input
terminals on the rear panel.
The selection of TAPE/MD MONITOR (MON) cannot be
canceled by pressing another input selector button. To
cancel it, press TAPE/MD MONITOR (MON) again so that
the “TAPE MON” indicator disappears from the display.
When you select a button other than TAPE/MD
MONITOR (MON), make sure that the “TAPE MON”
indicator is not illuminated on the display.
If you select the input selector button for a video source
without canceling the selection of TAPE/MD MONITOR
(MON), the playback result will be the video image from
the video source and the sound from the audio tape (or
MD etc.).
Once you play a video source, its video image will not be
interrupted even if the input selector button for an audio
source is selected.
When you finish using this unit
Press the STANDBY/ON switch again to turn this unit into the
standby mode.
BASIC OPERATIONS
TO PLAY A SOURCE
l6
20
28
40
60
l2
8
4
2
0
–dB
VOLUME
SPEAKERS
A
ON
OFF
B
l6
20
28
40
60
l2
8
4
2
0
–dB
VOLUME
TUNER
CD
PHONO
STANDBY/ON
1, 6
2
4
7
l6
20
28
40
60
l2
8
4
2
0
–dB
3
26
In step 3, press the button (shown below) once or more so that
“6ch” appears on the display.
Discrete signals from the unit connected to the 6CH
DISCRETE INPUT terminals of this unit are selected as the
input signals.
To cancel listening to a decoded source using Dolby
Digital (AC-3)
Press the same button again or select another input source.
Note for reproducing discrete signals with Dolby Digital
(AC-3) decoded:
1. Your speaker system must include a center speaker.
2. Your speaker system must include a subwoofer.
* Connect a subwoofer which has a built-in amplifier to the
SUBWOOFER OUTPUT terminal of this unit.
* You can do without using a subwoofer. If you do so, you
should make a setting for distributing signals at the LFE
channel to the right and left MAIN output terminals on the
Dolby Digital (AC-3) Decoder unit.
For details, refer to the owner’s manual for the Dolby
Digital (AC-3) Decoder unit.
Notes
When you switch to the “6ch” mode, the built-in Digital
Sound Field processor will not work and adjustment of delay
time cannot be made.
Switching this unit to the “6ch” mode will input no signal to
this unit if there is no connection to the 6CH DISCRETE
INPUT terminals of this unit.
To listen to a decoded source using Dolby Digital (AC-3) by reproducing the signals input to
the 6CH DISCRETE INPUT terminals of this unit.
RX-V393
RX-V493
DVD
/
LDTV
/
DBS
TAPE/MD MON 2CH/6CH
VIDEOVCR
2CH/6CH
DVD
/
LDTV
/
DBS
TAPE/MD MON 2CH/6CH
or
27
English
1 Select the source to be recorded.
2 Play the source and then turn the VOLUME control up
to confirm the input source. (For detailed information
on the tuning operations, refer to the page 29.)
3 Begin recording on the tape deck (or MD recorder etc.)
or VCR connected to this unit.
4 If the tape deck (or MD recorder etc.) is used for
recording, you can monitor the sounds being recorded
by pressing TAPE/MD MONITOR (MON) so that the
“TAPE MON” indicator lights up on the display.
Notes
The settings of DSP and the VOLUME, BASS, TREBLE
and BALANCE controls have no effect on the material
being recorded.
In step 1, do not make an input source selection so that
“6ch” appears on the display. Signals input to this unit’s
6CH DISCRETE INPUT terminals cannot be recorded by a
tape deck, MD recorder or VCR.
l6
20
28
40
60
l2
8
4
2
0
–dB
VOLUME
TO RECORD A SOURCE TO TAPE (OR MD)
2
l6
20
28
40
60
l2
8
4
2
0
–dB
1 4
TUNER
CD
PHONO
DVD
/
LDTV
/
DBS
CD
PHONO
TAPE/MD MON 2CH/6CH
2
l6
20
28
40
60
l2
8
4
2
0
–dB
14
RX-V393
RX-V493
RX-V393RX-V493
TAPE/MD
MONITOR
VCR
TUNER PHONO
1 Press once or more so that “SWFR” appears on the
display.
2 By continuously pressing the “+” or “–” side of the
TIME/LEVEL button, the level value changes continuously.
If you feel that bass tone is insufficient, increase the level,
and if you feel that bass tone is overly emphasized,
decrease the level.
Control range: MIN, –20 to 0 dB
28
Selecting the SPEAKER system
Because one or two speaker systems (as main speakers) can
be connected to this unit, the SPEAKERS switches allow you
to select speaker system A or B, or both at once.
Adjusting the BALANCE control
Adjust the balance of the output volume to the left and right
speakers to compensate for sound imbalance caused by
speaker location or listening room conditions.
Note
This control is effective only for the sound from the main
speakers.
Adjusting the BASS and TREBLE
controls
BASS : Turn this clockwise to increase (or counter-
clockwise to decrease) the low frequency
response.
TREBLE : Turn this clockwise to increase (or counter-
clockwise to decrease) the high frequency
response.
Note
These controls are effective only for the sound from the main
speakers.
SPEAKERS
A
ON
OFF
B
BALANCE
55
4
3
2
l
0
l
2
3
4
LR
BASS TREBLE
55
4
3
2
l
0
l
2
3
4
55
4
3
2
l
0
l
2
3
4
Adjusting the subwoofer output level
RX-V493 only
RX-V493 only
If your audio system includes a subwoofer, and an amplifier driving the subwoofer (or a subwoofer system including an amplifier) is
connected to the SUBWOOFER OUTPUT terminal on the rear of this unit, you can adjust the subwoofer output level on this unit.
DELAY/CENTER
/REAR/SWFR
TIME
/
LEVEL
Adjustable
29
English
1 Select “TUNER” as the input source.
2 Select the reception band (FM or AM) confirming it on
the display.
3
4 Tune to a desired station manually.
* To continue tuning search, press and hold the button.
1 Select “TUNER” as the input source.
2 Select the reception band (FM or AM) confirming it on
the display.
3
4
To tune to a higher frequency, press the right side once.
To tune to a lower frequency, press the left side once.
* If the station where tuning search stops is not the desired
one, press again.
* If the tuning search does not stop at the desired station
(because the signals of the station are weak), change to
the MANUAL TUNING method.
TUNING OPERATIONS
Normally, if station signals are strong and there is no interference, quick automatic-search tuning (AUTOMATIC TUNING) is
possible. However, if signals of the station you want to select are weak, you must tune to it manually (MANUAL TUNING).
Note
If you tune to an FM station manually, it is received in monaural
mode automatically to increase the signal quality.
AUTOMATIC TUNING MANUAL TUNING
FM
/
AM
TUNING
MODE
AUTO
/
MAN’L MONO
TUNING
MODE
AUTO
/
MAN’L MONO
DOWN
TUNING
UP
DOWN
TUNING
UP
Turn the “AUTO”
indicator off.
21
l6
20
28
40
60
l2
8
4
2
0
–dB
34
or
FM
/
AM
or
AUTO
TUNER
CD
PHONO
TUNER
CD
PHONO
30
1 Tune to a desired station.
(Refer to the previous page for tuning procedure.)
2 Select a desired group (A – E) of preset stations
confirming it on the display.
3
4 Select a preset station number where you want to
program the station before the “MEMORY” indicator
goes off from the display.
* In the same way, program other stations to A2, A3 ... A8.
* You can program more stations to preset station numbers
on other groups in the same way by selecting other groups
in step 2.
11 Select the group of preset stations.
22 Select the preset station number.
Notes
A new setting can be programmed in place of the former
one.
For presets, the setting of the reception mode (stereo or
monaural) is stored along with the station frequency.
Memory back-up
The memory back-up circuit prevents the programmed data
from being lost even if this unit is turned into the standby
mode or the power plug is disconnected from the AC outlet or
the power is cut due to temporary power failure. If, however,
the power is cut for more than one week, the memory may be
erased. If so, it can be re-programmed by simply following
the PRESET TUNING steps.
MANUAL PRESET TUNING
This unit can store station frequencies selected by tuning operation. With this function, you can recall any desired station by only
selecting the preset station number where it is stored. Up to 40 stations (8 stations x 5 groups) can be stored.
PRESET TUNING
To store stations
To recall a preset station
2, 11 34, 22
MAN’L
/
AUTO FM
MEMORY
MEMORY
A
/
B
/
C
/
D
/
E
PRESET
A
/
B
/
C
/
D
/
E
Flashes on and off
for about 5 seconds.
PRESET
MHz
AUTO
STEREO
0
20
l00
CONCERT HALL
Shows the displayed station has been
programmed to A1.
l6
20
28
40
60
l2
8
4
2
0
–dB
1
2 3 4 5 6 7 8
1
2 3 4 5 6 7 8
31
English
1
2
3
To tune to higher frequencies, press right side once.
To tune to lower frequencies, press left side once.
* If the TUNING button is not pressed, in a while, the
automatic preset tuning begins automatically toward higher
frequencies.
The automatic preset tuning begins from the frequency
currently displayed. Received stations are programmed to
A1, A2 ... A8 sequentially.
* If more than 8 stations are received, they are also
programmed to the preset station numbers on other groups
(B, C, D and E) in that order.
If you want to store the first station received by the
automatic preset tuning to a desired preset station
number.
If, for example, you want to store the first received station to
C5, select “C5” by using the A/B/C/D/E button and the preset
station number selector buttons after pressing the MEMORY
button in step 2. Then press the TUNING button. The first
received station is stored to C5, and next stations to C6, C7 ...
sequentially.
If stations are stored up to E8, the automatic preset tuning is
finished automatically.
When the automatic preset tuning is finished
The display shows the frequency of the last preset station.
Check the contents and the number of preset stations by
following the procedure of the section “To recall a preset
station” on page 30.
To recall a preset station
Simply follow the procedure of the section “To recall a preset
station” on page 30.
Notes
You can replace a preset station by another FM or AM
station manually by simply following the procedure of the
section “To store stations” on page 30.
If the number of received stations is not enough to be stored
up to E8, the search is finished automatically after searching
all frequencies.
With this function, only FM stations with sufficient signal
strength are stored automatically. If the station you want to
program is weak in signal strength, tune to it in monaural
manually and program it by following the procedure of the
section “To store stations” on page 30.
AUTOMATIC PRESET TUNING
You can also make use of an automatic preset tuning function for FM stations only. By this function, this unit performs automatic
tuning and stores FM stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the
manual preset tuning method on page 30.
To store stations
Press and hold for
about 3 seconds.
FM
/
AM
MAN’L
/
AUTO FM
MEMORY
l6
20
28
40
60
l2
8
4
2
0
–dB
132
Flashes.
DOWN
TUNING
UP
PRESET
MEMORY
AUTO
32
EXCHANGING PRESET STATIONS
You can exchange the places of two preset stations with each other as shown below.
Example)
If you want to shift the preset station on E1 to A5, and vice
versa.
1 Recall the preset station on E1 (by following the method
of “To recall a preset station” on page 30).
2
3 Next, recall the preset station on A5 by following the
same method with step 1.
4
Shows the exchange of stations is completed.
Flashes.
Flashes.
EDIT
EDIT
MEMORY
PRESET
MEMORY
PRESET
2, 4
l6
20
28
40
60
l2
8
4
2
0
–dB
33
English
Brief Overview of Digital Sound Field Programs
The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in mind that most of
these are precise digital recreations of actual acoustic environments. The data for these sound fields was recorded at actual
locations using sophisticated sound field measurement equipment.
Note
The channel level balance between the left and right rear effect speakers may vary depending on the sound field you are
listening to. This is due to the fact that most of these sound field recreations are actual acoustic environments.
PROGRAM FEATURE
This program is used for playback of sources encoded with Dolby Surround.
PRO LOGIC The application of a sophisticated digital signal processing system reduces crosstalk and directs or steers
the sound source more smoothly and precisely, as compared to conventional types.
This program is also used for playback of sources encoded with Dolby Surround.
PRO LOGIC
Enhancing the “Normal” Dolby Pro Logic, the DSP technology simulates the multi-surround speaker
ENHANCED
systems of a 35 mm movie theater. This effect creates a wide surround sound field, and expands the
sound stage with an improved presence image. This program is used for musical based movies, as well as
drama and comedy based movies.
CONCERT VIDEO
This program is effective for music videos and gives excellent depth and clarity for vocals. For opera, the
orchestra and stage are ideally recreated, letting you feel as if you were in an actual concert hall.
MONO MOVIE
This program is designed specifically to enhance mono source programs. Compared to a strictly mono
setting, the sound image created in this mode is wider and slightly forward of the speaker pair, lending an
immediacy to the overall sound. It is particularly effective when used with old mono movies, news
broadcasts and dialog.
STADIUM
This program gives you long delays between direct sounds and effect sounds, and extraordinarily
spacious feel of a large stadium.
DISCO
This program recreates the acoustic environment of a lively disco in the heart of a very lively city. The
sound is dense and highly concentrated. It is also characterized by a high-energy, “immediate” sound.
ROCK CONCERT This program is ideally suited for rock music. You will experience a very dynamic or lively sound field.
CONCERT HALL
In this program, the center will appear to be deep behind the main speakers, creating an expansive large
hall ambience. Orchestra and opera music are suited for this sound field.
USING DIGITAL SOUND FIELD PROCESSOR (DSP)
This unit incorporates a sophisticated, multi-program digital sound field processor. The processor allows you to electronically expand
and change the shape of the audio sound field from both audio and video sources, creating a theater-like experience in your
listening room. You can create an excellent audio sound field by selecting a suitable sound field program (this will, of course, depend
on what you will be listening to), and adding desired adjustments.
In addition, this unit incorporates a Dolby Pro Logic Surround decoder for multi-channel sound reproduction of sources encoded with
Dolby Surround. The operation of the Dolby Pro Logic Surround decoder can be controlled by selecting a corresponding DSP
program including a combined operation of the Yamaha DSP and the Dolby Pro Logic Surround.
34
1 Follow steps 1 – 6 shown in “BASIC OPERATIONS” on
page 25.
2 Select the desired program that is suitable for the
source.
a)
Turn the DSP on so that a
program name lights up on
the display.
b)
Select a desired program
confirming it on the display.
The selected program name is shown on the display.
3 If desired, adjust the delay time and the output level of
each speaker. (For details, refer to the corresponding
descriptions on page 35 and 36.)
Notes
Program selection can be made to individual input sources.
Once you select a program, it is linked with the input source
selected at that time. So, when you select the input source
next time, the same program is automatically called.
If you prefer to cancel the DSP, press the EFFECT button.
The sound will be the normal 2-channel stereo without
surround sound effect.
When CONCERT VIDEO, MONO MOVIE, STADIUM,
DISCO, ROCK CONCERT or CONCERT HALL is selected,
no sound is heard from the center speaker.
When a monaural sound source is played with DOLBY PRO
LOGIC or DOLBY PRO LOGIC ENHANCED, no sound is
heard from the main speakers and the rear speakers.
Sound is heard only from the center speaker. However, if
the center channel mode is in PHANTOM, the main
speakers output the sound of the center channel.
When this unit’s Dolby Pro Logic Surround decoder is used,
if the main-source sound is considerably altered by
overadjustment of the BASS or TREBLE control, the
relationship between the center and rear channels may
produce an unnatural effect.
To select a DSP program on the remote control transmitter,
first turn the DSP on so that a program name lights up on
the display by pressing the EFFECT key. Next, select a
desired DSP program by pressing the or side of
PROGRAM key.
* Pressing the PROLOGIC or ENHANCED key turns
the DSP on and selects the corresponding program
directly.
To play a source with the digital sound field processor
PROGRAM
PRO LOGIC
l6
20
28
40
60
l2
8
4
2
0
–dB
2
EFFECT
ON/OFF
PROLOGIC
ENHANCED
l6
20
28
40
60
l2
8
4
2
0
–dB
2
2CH
/6CH
REC/PAUSE
DIR BDIR A
PLAY
DISC
VOLUME
PLAY
PRESET
A/B/C/D/E
–+
TESTDELAY TIME
EFFECT
PROGRAM
PROLOGIC
ENHANCED
–+
SLEEP
TAPE
A/B
ON/OFF
TUNER
CD
PHONO
VIDEO
VCR
POWER /I
RX-V393
RX-V493
REC/PAUSE
DIR BDIR A
PLAY
DISC
POWER /I
VOLUME
PLAY
PRESET
A/B/C/D/E
–+
TIME/
LEVEL
TEST
EFFECT
PROGRAM
PROLOGIC
ENHANCED
–+
SLEEP
TAPE
A/B
ON/OFF
2CH
/6CH
TUNER
CD
PHONO
DELAY/CENTER
/REAR/SWFR
DVD/LD
VCR
TV/DBS
2
2
RX-V393RX-V493
PRO LOGIC
PRO LOGIC
ENHANCED
EFFECT
PROGRAM
35
English
If desired, you can adjust the sound output level of the center
speaker even if the output level is already set in “SPEAKER
BALANCE ADJUSTMENT” on page 24.
1 Press once or more so that “CENTER” appears on the
display.
2 By continuously pressing the “+” or “–” side of the
TIME/LEVEL button, the level value changes continuously.
The value stops changing momentarily at the preset point
(0 dB).
Control range: MIN, –20 to +10 dB
Notes
This adjustment can be made only when the digital sound
field program DOLBY PRO LOGIC or DOLBY PRO LOGIC
ENHANCED is selected.
Once the output level is adjusted, the level value will be the
same in all the digital sound field programs mentioned
above.
Note
This adjustment is useful only when the digital sound field
program DOLBY PRO LOGIC or DOLBY PRO LOGIC
ENHANCED is selected.
Adjustment of the CENTER LEVEL
TIME
/
LEVEL
DELAY/CENTER
/REAR/SWFR
Adjustable
Adjustment of the REAR LEVEL
If desired, you can adjust the sound output level of the rear
speakers even if the output level is already set in “SPEAKER
BALANCE ADJUSTMENT” on page 24.
1 Press once or more so that “REAR” appears on the display.
2 By continuously pressing the “+” or “–” side of the
TIME/LEVEL button, the level value changes continuously.
The value stops changing momentarily at the preset point
(0 dB).
Control range: MIN, –20 to +10 dB
Notes
This adjustment can be made only when the built-in digital
sound field processor is on.
Once the output level is adjusted, the level value will be the
same in all the digital sound field programs.
Note
If no digital sound field program is used, this adjustment is
useless.
TIME
/
LEVEL
DELAY/CENTER
/REAR/SWFR
Adjustable
RX-V493
RX-V393
RX-V493
RX-V393
CENTER
LEVEL
0l0
REAR
LEVEL
0l0
36
Adjustment of DELAY TIME
You can adjust the time difference between the beginning of
the sound from the main speakers and the beginning of the
effect sound from the rear speakers.
The larger the value, the later the effect sound is generated.
This adjustment can be made to all programs individually.
PRO LOGIC : from 15 to 30 milliseconds
(Preset value: 20 milliseconds)
PRO LOGIC : from 15 to 30 milliseconds
ENHANCED (Preset value: 20 milliseconds)
CONCERT VIDEO : from 1 to 100 milliseconds
(Preset value: 28 milliseconds)
MONO MOVIE : from 1 to 100 milliseconds
(Preset value: 20 milliseconds)
STADIUM : from 1 to 50 milliseconds
(Preset value: 45 milliseconds)
DISCO : from 1 to 100 milliseconds
(Preset value: 14 milliseconds)
ROCK CONCERT : from 1 to 100 milliseconds
(Preset value: 17 milliseconds)
CONCERT HALL : from 1 to 100 milliseconds
(Preset value: 30 milliseconds)
1 Press once or more so that “DELAY” appears on the
display.
2 By continuously pressing the “+” or “–” side of the
TIME/LEVEL button, the value changes continuously.
The value stops changing momentarily at the preset point.
Notes
When the TIME/LEVEL button is pressed, sound is
momentarily interrupted.
Adding too much delay will cause an unnatural effect with
some sources.
This adjustment can be made by only using the remote control
transmitter.
Notes
When the DELAY TIME key is pressed, sound is
momentarily interrupted.
Adding too much delay will cause an unnatural effect with
some sources.
Notes
RX-V493 only
The values of the delay time, center level, rear level and
subwoofer output level you set the last time will remain
memorized even when this unit is in the standby mode.
However, if the power cord is kept disconnected for more than
one week, these values will be automatically changed back to
the original factory settings.
RX-V393 only
The value of the delay time you set the last time will remain
memorized even when this unit is in the standby mode.
However, if the power cord is kept disconnected for more than
one week, these values will be automatically changed back to
the original factory settings.
TIME
/
LEVEL
DELAY/CENTER
/REAR/SWFR
Adjustable
RX-V493
RX-V393
ms
ms
DELAY TIME
Adjustable
ms
37
English
1
Whenever the SLEEP key is pressed, the SLEEP time will
change as follows.
After a while, the display returns to the indication before
the SLEEP timer is set.
2 The unit will be turned into the standby mode
automatically at the selected SLEEP time.
SETTING THE SLEEP TIMER
If you use the SLEEP timer of this unit, you can make this unit turn into the standby mode. When you are going to sleep while
enjoying a broadcast or other desired input source, this timer function is helpful.
Notes
The SLEEP timer can be controlled only with the remote control transmitter.
The components on which the SLEEP timer is effective are the sources connected to the SWITCHED AC OUTLET(S) on the rear
panel of this unit.
To set the SLEEP time
Press once or more to select the desired
SLEEP time.
To cancel the selected SLEEP time
Press once or more so that “SLEEP OFF” appears on the
display. (It will soon disappear and the “SLEEP” indicator will
go off from the display.)
Note
The SLEEP timer setting can also be canceled by turning this
unit into the standby mode with the STANDBY/ON switch or
disconnecting the power plug of this unit from the AC outlet.
Indicates the SLEEP time.
Lights up.
120 90 60 30
The SLEEP timer is off (OFF).
(The state before the SLEEP key
is pressed.)
(Minutes)
SLEEP
SLEEP
SLEEP
CONCERT HALL
38
AmplifierFMAMOthers
Remote control
transmitter
If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple
measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and
contact your authorized YAMAHA dealer or service center for help.
SYMPTOM
The unit fails to turn on when the STANDBY/ON
switch is pressed, or turns into the standby
mode suddenly soon after the power is turned
on.
It happens that this unit does not work
normally.
No sound or no picture.
The sound suddenly goes off.
Only one side speaker outputs the sound.
Sound “hums”.
The volume level is low while playing a record.
The volume level cannot be increased, or
sound is distorted.
No sound from the rear speakers.
No sound from the center speaker.
FM stereo reception is noisy.
There is distortion and clear reception cannot
be obtained even with a good FM antenna.
A desired station cannot be tuned in with the
automatic tuning method.
Previously preset stations can no longer be
tuned in.
A desired station cannot be tuned in with the
automatic tuning method.
There are continuous crackling and hissing
noises.
There are buzzing and whining noises
(especially in the evening).
The remote control transmitter does not work.
The sound is degraded when listening with the
headphones connected to the compact disc
player or cassette deck that are connected with
this unit.
CAUSE
Power cord is not plugged in or is not completely
inserted.
The IMPEDANCE SELECTOR switch on the rear
panel is not set to the upper or the lower end
closely.
There is an influence of strong external noise
(lightning, excessive static electricity, etc.) or a
misoperation on this unit while using this unit.
Incorrect output cord connections.
Appropriate input source is not selected.
The SPEAKERS switches are not set properly.
Speaker connections are not secure.
The protection circuit has been activated because
of short circuit etc.
The SLEEP timer has functioned.
Incorrect setting of the BALANCE control.
Incorrect cord connections.
Incorrect cord connections.
No connection from the turntable to the GND
terminal.
The record is being played on a turntable with an
MC cartridge.
The component connected to the REC OUT
terminals of this unit is in the standby mode.
The sound output level to the rear speakers is set
to minimum.
The monaural sound source is played in DOLBY
PRO LOGIC or DOLBY PRO LOGIC ENHANCED
mode.
The sound output level to the center speaker is set
to minimum.
The center channel mode is in PHANTOM mode.
Incorrect sound field program selection.
Because of the characteristics of FM stereo
broadcasts, this is limited to cases where the
transmitter is too far away or the antenna input is
poor.
There is multipath interference.
The station is too weak.
This unit has been unplugged for a long period.
Weak signal or loose antenna connections.
Noises will result from ligtning, fluorescent lamps,
motors, thermostats and other electrical equipment.
A television set is being used nearby.
Direct sunlight or lighting (of an inverter type of
fluorescent lamp etc.) is striking the remote control
sensor of the main unit.
The batteries of this remote control transmitter are
too weak.
This unit is in the standby mode.
REMEDY
Firmly plug in the power cord.
Set the switch to the upper or the lower end closely.
Turn this unit into the standby mode and disconnect
the AC power cord from the AC outlet. After about
30 seconds have passed, connect the power and
operate this unit again.
Connect the cords properly. If the problem persists,
the cords may be defective.
Select an appropriate input source with the input
selector buttons.
Set the SPEAKERS switch which corresponds to
the speakers to be used to the ON position.
Secure the connections.
Turning the unit into the standby mode and then on
will reset the protection circuit.
Cancel the SLEEP timer function.
Adjust it to the appropriate position.
Connect the cords properly. If the problem persists,
the cords may be defective.
Firmly connect the audio plugs. If the problem
persists, the cords may be defective.
Make the GND connection between the turntable
and this unit.
The player should be connected to the unit through
the MC head amplifier.
Turn the power to the component on.
Raise the sound output level to the rear speakers.
Select another program suitable for the monaural
sound source.
Raise the sound output level to the center speaker.
Select NORMAL or WIDE.
Select the appropriate program.
Check the antenna connections.
Try using a high quality directional FM antenna.
Set the TUNING MODE button to the manual tuning
mode.
Adjust antenna placement to eliminate multipath
interference.
Use the manual tuning method.
Use a high quality directional FM antenna.
Repeat the presetting procedure.
Tighten the AM loop antenna connections and
rotate it for best reception.
Use the manual tuning method.
Use an outdoor antenna and a ground wire. This
will help somewhat but it is difficult to eliminate all
noise.
Relocate this unit away from the TV.
Change the position of the main unit.
Replace the batteries with new ones.
Turn the power to this unit on.
TROUBLESHOOTING
39
English
AUDIO SECTION
Minimum RMS Output Power per Channel
Main L, R
8 ohms, 20 Hz to 20 kHz, 0.04% THD
<RX-V493>
[U.S.A. and Canada models]
.................................................70W+70W
[Europe, Australia, China and General
models] ....................................65W+65W
<RX-V393>...............................50W+50W
Center
8 ohms, 1 kHz, 0.04% THD
<RX-V493>
[U.S.A. and Canada models]
..........................................................70W
[Europe, Australia, China and General
models]..............................................65W
<RX-V393>........................................50W
Rear L, R
8 ohms, 1 kHz, 0.04% THD ..........20W+20W
Maximum Power [China and General models
only]
8 ohms, 1 kHz, 10% THD
Main L, R
<RX-V493>........................100W+100W
<RX-V393>............................75W+75W
Center
<RX-V493>....................................100W
<RX-V393>......................................75W
Rear L, R.......................................30W+30W
Dynamic Power per Channel
(by IHF Dynamic Headroom measuring
method)
<RX-V493>
8/6/4/2 ohms
[U.S.A. and Canada models]
...................................100/120/150/175W
[Europe, Australia, China and General
models].........................95/115/145/165W
<RX-V393>
8/6/4/2 ohms
[U.S.A. and Canada models]
.......................................80/95/120/140W
[Europe, Australia, China and General
models].........................80/100/120/135W
DIN Standard Output Power per Channel
[Europe model only]
4 ohms, 1 kHz, 0.7% THD
<RX-V493>......................................95W
<RX-V393>......................................75W
Dynamic Headroom (8 ohms)
[U.S.A. and Canada models only]
<RX-V493>...................................1.55 dB
<RX-V393>...................................2.04 dB
IEC Power [Europe model only]
8 ohms, 1 kHz, 0.1% THD
<RX-V493>........................................80W
<RX-V393>........................................60W
Power Band Width
<RX-V493>
8 ohms, 30W, 0.1% THD
...........................................10 Hz to 50 kHz
<RX-V393>
8 ohms, 25W, 0.1% THD
...........................................10 Hz to 50 kHz
Damping Factor (SPEAKERS A)
8 ohms, 20 Hz to 20 kHz
...............80 or more
Input Sensitivity/Impedance
<RX-V493>
PHONO MM...................2.5 mV/47 k-ohms
CD/TAPE·MD/DVD·LD/TV·DBS/VCR
......................................150 mV/47 k-ohms
6CH DISCRETE INPUT
MAIN...........................150 mV/56 k-ohms
CENTER.....................150 mV/40 k-ohms
SURROUND...............100 mV/40 k-ohms
SUBWOOFER............150 mV/40 k-ohms
<RX-V393>
PHONO MM...................2.5 mV/47 k-ohms
CD/TAPE·MD/VIDEO/VCR
......................................150 mV/47 k-ohms
6CH DISCRETE INPUT
MAIN...........................150 mV/56 k-ohms
CENTER.....................150 mV/11 k-ohms
SURROUND...............100 mV/11 k-ohms
SUBWOOFER............150 mV/40 k-ohms
Maximum Input Signal
<RX-V493>
PHONO MM
1 kHz, 0.5% THD..........................100 mV
CD/TAPE·MD/DVD·LD/TV·DBS/VCR
(EFFECT OFF)
1 kHz, 0.5% THD...............................2.5V
<RX-V393>
PHONO MM
1 kHz, 0.5% THD..........................100 mV
CD/TAPE·MD/VIDEO/VCR (EFFECT OFF)
1 kHz, 0.5% THD...............................2.5V
Output Level/Impedance
REC OUT........................150 mV/2.5 k-ohms
CENTER OUTPUT.................2V/1.2 k-ohms
REAR OUTPUT...................1.2V/1.2 k-ohms
SUBWOOFER OUTPUT (EFFECT OFF)
................................................4V/1.2 k-ohms
Headphones Jack Rated Output/Impedance
Output Level (8 ohms, 0.04% THD) .....0.45V
Impedance .....................................330 ohms
Frequency Response (20 Hz to 20 kHz)
<RX-V493>
CD/TAPE·MD/DVD·LD/TV·DBS/VCR
......................................................0±0.5 dB
<RX-V393>
CD/TAPE·MD/VIDEO/VCR
............0±0.5 dB
RIAA Equalization Deviation
PHONO MM....................................0±0.5 dB
Total Harmonic Distortion (20 Hz to 20 kHz)
<RX-V493>
PHONO MM to REC OUT
1V...................................................0.02%
CD/TAPE·MD/DVD·LD/TV·DBS/VCR
to SP OUT
30W/8 ohms ...................................0.03%
<RX-V393>
PHONO MM to REC OUT
1V...................................................0.02%
CD/TAPE·MD/VIDEO/VCR
to SP OUT
30W/8 ohms ...................................0.03%
Signal-to-Noise Ratio (IHF-A Network)
<RX-V493>
PHONO MM to REC OUT
(5 mV Input Shorted)..........................80 dB
CD/TAPE·MD/DVD·LD/TV·DBS/VCR
to SP OUT (Shorted)..........................93 dB
<RX-V393>
PHONO MM to REC OUT
(5 mV Input Shorted)..........................80 dB
CD/TAPE·MD/VIDEO/VCR
to SP OUT
(Shorted)............................................93 dB
Residual Noise (IHF-A Network)
MAIN L/R............................................140 µV
Channel Separation (Vol. –30 dB, EFFECT
OFF)
<RX-V493>
PHONO MM
(Input Shorted, 1 kHz).....................60 dB
CD/TAPE·MD/DVD·LD/TV·DBS/VCR
(Input 5.1 k-ohms Terminated, 1 kHz)
........................................................60 dB
<RX-V393>
PHONO MM
(Input Shorted, 1 kHz).....................60 dB
CD/TAPE·MD/VIDEO/VCR
(Input 5.1 k-ohms Terminated, 1 kHz)
........................................................60 dB
Tone Control Characteristics
BASS: Boost/cut...............±10 dB (50 Hz)
Turnover Frequency...........350 Hz
TREBLE: Boost/cut.............±10 dB (20 kHz)
Turnover Frequency..........3.5 kHz
Gain Tracking Error (0 to –60 dB).............3 dB
VIDEO SECTION
Video Signal Level ..................1 Vp-p/75 ohms
Maximum Input Level ............1.5 Vp-p or more
Signal-to-Noise Ratio.................50 dB or more
Monitor Out Frequency Response
.....................................5 Hz to 10 MHz, –3 dB
SPECIFICATIONS
40
FM SECTION
Tuning Range
[U.S.A. and Canada models]
..........................................87.5 to 107.9 MHz
[Europe, Australia, China and General
models]..............................87.5 to 108.0 MHz
50 dB Quieting Sensitivity (IHF, 75 ohms)
[U.S.A., Canada, Australia, China and
General models only]
Mono...............................1.55 µV (15.1 dBf)
Stereo................................21 µV (37.7 dBf)
Usable Sensitivity (75 ohms)
[Europe and Australia models only]
DIN, Mono (S/N 26 dB)......................0.9 µV
DIN, Stereo (S/N 46 dB).....................24 µV
Image Response Ratio
[U.S.A., Canada, China and General models]
..............................................................45 dB
[Europe and Australia models] .............80 dB
IF Response Ratio
[U.S.A., Canada, China and General models]
..............................................................70 dB
[Europe and Australia models] .............80 dB
Spurious Response Ratio.........................70 dB
AM Suppression Ratio..............................55 dB
Capture Ratio ..........................................1.5 dB
Alternate Channel Selectivity
[
U.S.A., Canada, China and General models
only] .......................................................85 dB
Selectivity (two signals, 40 kHz Dev.
±300
kHz)
[Europe and Australia models only]
...............................................................70 dB
Signal-to-Noise Ratio
(IHF) Mono/Stereo
[U.S.A., Canada, China and General
models] .....................................80 dB/75 dB
(DIN-Weighted, 40 kHz Dev.) Mono/Stereo
[
Europe and Australia models
]
..................................................75 dB/70 dB
Harmonic Distortion (1 kHz)
[U.S.A., Canada
, Australia,
China and
General models]
Mono/Stereo...................................0.1/0.2%
[
Europe model
]
Mono/Stereo (40 kHz Dev.)............0.1/0.2%
Stereo Separation (1 kHz)
[U.S.A., Canada
, Australia,
China and
General models
]...................................50 dB
[
Europe model (40 kHz Dev.)]..............50 dB
Frequency Response
20 Hz to 15 kHz..............................0 ±1.5 dB
AM SECTION
Tuning Range
[U.S.A., Canada, China and General models]
.............................................530 to 1,710 kHz
[
Europe and Australia models
]
.............................................531 to 1,611 kHz
Usable Sensitivity..............................100 µV/m
Selectivity................................................32 dB
Signal-to-Noise Ratio..............................50 dB
Image Response Ratio ...........................40 dB
Spurious Response Ratio .......................50 dB
Harmonic Distortion (1 kHz).....................0.3%
AUDIO SECTION
Output Level/Impedance
FM (100% mod., 1 kHz)
[U.S.A., Canada
, Australia,
China and
General models]............500 mV/2.2 k-ohms
[
Europe model
(40 kHz Dev.)]
......................................400 mV/2.2 k-ohms
AM (30% mod., 1 kHz)
.........................................150 mV/2.2 k-ohms
GENERAL
Power Supply
[U.S.A. and Canada models]
..............................................AC 120V, 60 Hz
[Europe model]......................AC 230V, 50 Hz
[Australia model]...................AC 240V, 50 Hz
[China and General models]
....................AC 110/120/220/240V, 50/60 Hz
Power Consumption
<RX-V493>
[U.S.A. model]....................................220W
[Except U.S.A. model]........................230W
<RX-V393>
[U.S.A. model]....................................190W
[Canada model]..................................210W
[Europe, Australia, China and General
models] ..............................................200W
Maximum Power Consumption [General model
only] (
8 ohms, 1 kHz, 10% THD, When 5
channels are driven:)
<RX-V493>.........................................540W
<RX-V393>.........................................430W
AC Outlets
2 SWITCHED OUTLETS
[U.S.A., Canada, Europe, China and
General models]................100W max. total
1 SWITCHED OUTLET
[Australia model]................100W max. total
Dimensions (W x H x D)
......................................435 x 151 x 308.5 mm
(17-1/8” x 5-15/16” x 12-1/8”)
Weight
<RX-V493>.................8.7 kg (19 lbs. 2 oz.)
<RX-V393>.................7.8 kg (17 lbs. 3 oz.)
Accessories...........................AM loop antenna
Indoor FM antenna
Remote control transmitter
Batteries
Antenna adapter
(U.S.A. and Canada models only)
Specifications are subject to change without
notice.
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
VZ38280 Printed in Malaysia

Transcripción de documentos

UCA RX-V493 RX-V393 Natural Sound AV Receiver Récepteur audiovisuel “Son Naturel” Thank you for selecting this YAMAHA AV receiver. Nous vous remercions d’avoir porté votre choix sur ce récepteur audiovisuel YAMAHA. OWNER’S MANUAL MODE D’EMPLOI SAFETY INSTRUCTIONS 7 Wall or Ceiling Mounting – The unit should be mounted to a wall or ceiling only as recommended by the manufacturer. 8 Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation. For example, the unit should not be situated on a bed, sofa, rug, or similar surface, that may block the ventilation openings; or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings. 9 Heat – The unit should be situated away from heat sources such as radiators, stoves, or other appliances that produce heat. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. • Explanation of Graphical Symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. 10 Power Sources – The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the unit. 11 Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the unit. 12 Cleaning – The unit should be cleaned only as recommended by the manufacturer. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. 1 Read Instructions – All the safety and operating instructions should be read before the unit is operated. 2 Retain Instructions – The safety and operating instructions should be retained for future reference. 3 Heed Warnings – All warnings on the unit and in the operating instructions should be adhered to. 4 Follow Instructions – All operating and other instructions should be followed. 5 Water and Moisture – The unit should not be used near water – for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc. 6 Carts and Stands – The unit should be used only with a cart or stand that is recommended by the manufacturer. 6A A unit and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the unit and cart combination to overturn. 13 Nonuse Periods – The power cord of the unit should be unplugged from the outlet when left unused for a long period of time. 14 Object and Liquid Entry – Care should be taken so that objects do not fall into and liquids are not spilled into the inside of the unit. 15 Damage Requiring Service – The unit should be serviced by qualified service personnel when: A. The power-supply cord or the plug has been damaged; or B. Objects have fallen, or liquid has been spilled into the unit; or C. The unit has been exposed to rain; or D. The unit does not appear to operate normally or exhibits a marked change in performance; or E. The unit has been dropped, or the cabinet damaged. 16 Servicing – The user should not attempt to service the unit beyond those means described in the operating instructions. All other servicing should be referred to qualified service personnel. 17 Power Lines – An outdoor antenna should be located away from power lines. 18 Grounding or Polarization – Precautions should be taken so that the grounding or polarization is not defeated. English 19 For US customers only: Outdoor Antenna Grounding – If an outside antenna is connected to this unit, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. EXAMPLE OF ANTENNA GROUNDING MAST ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810–20) ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810–21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H) NEC – NATIONAL ELECTRICAL CODE SPECIAL NOTES FOR FCC COMPOSITE DEVICE (for US customers only) This device is a composite system. The digital device component may not cause harmful interference. FCC INFORMATION (for US customers only) 1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT : When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE : This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620. The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. We Want You Listening For A Lifetime (for US customers only) YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels. 1 CONTENTS Safety Instructions ..............Inside the Front Cover Speaker Balance Adjustment .......................22 Supplied Accessories .....................................2 Basic Operations ..........................................25 Features .........................................................3 Tuning Operations ........................................29 Caution ...........................................................4 Preset Tuning ...............................................30 Notes about the Remote Control Transmitter Using Digital Sound Field Processor (DSP) .......................................................................5 .....................................................................33 Profile of This Unit ..........................................6 Setting the SLEEP Timer .............................37 Speaker Setup ................................................7 Troubleshooting ............................................38 Connections ...................................................8 Specifications ...............................................39 Controls and Their Functions .......................16 SUPPLIED ACCESSORIES After unpacking, check that the following parts are included. Indoor FM Antenna Remote Control Transmitter RX-V493 AM Loop Antenna TIME/ LEVEL – + DELAY/CENTER /REAR/SWFR TEST PROGRAM PROLOGIC ENHANCED VCR RX-V393 EFFECT – DELAY TIME + ON/OFF PROGRAM TV/DBS DVD/LD TEST VCR DIR B REC/PAUSE – + PLAY A/B PRESET A/B/C/D/E DISC PLAY 2CH /6CH DIR A DIR B REC/PAUSE – + TAPE TUNER PLAY A/B PRESET A/B/C/D/E DISC CD PLAY PHONO POWER SLEEP Antenna adapter (U.S.A. and Canada models only) Batteries (size AA, R6, UM-3) 2 /I ON/OFF VIDEO 2CH /6CH DIR A EFFECT PROLOGIC ENHANCED TAPE TUNER CD PHONO VOLUME POWER SLEEP /I VOLUME ● 5 Speaker Configuration RX-V493 Main: <U.S.A. and Canada models> 70W + 70W (8Ω) RMS Output Power, 0.04% THD, 20–20,000 Hz <Europe, Australia, China and General models> 65W + 65W (8Ω) RMS Output Power, 0.04% THD, 20–20,000 Hz Center: <U.S.A. and Canada models> 70W (8Ω) RMS Output Power, 0.04% THD, 1 kHz <Europe, Australia, China and General models> 65W (8Ω) RMS Output Power, 0.04% THD, 1 kHz Rear: 20W + 20W (8Ω) RMS Output Power, 0.04% THD, 1 kHz RX-V393 Main: 50W + 50W (8Ω) RMS Output Power, 0.04% THD, 20–20,000 Hz Center: 50W (8Ω) RMS Output Power, 0.04% THD, 1 kHz Rear: 20W + 20W (8Ω) RMS Output Power, 0.04% THD, 1 kHz ● Digital Sound Field Processor English FEATURES ● Dolby Pro Logic Surround Decoder ● Theater-like Sound Experience by the Combination of Dolby Pro Logic and YAMAHA DSP Technology (CINEMA DSP) ● Automatic Input Balance Control for Dolby Pro Logic Surround ● Test Tone Generator for Easier Speaker Balance Adjustment ● 3 Center Channel Modes (NORMAL/WIDE/PHANTOM) ● 40-Station Random Access Preset Tuning ● Automatic Preset Tuning ● Preset Station Shifting Capability (Preset Editing) ● IF Count Direct PLL Synthesizer Tuning System ● 6-Channel Discrete Input Terminals for Connecting with a Dolby Digital (AC-3) Decoder ● Video Signal Input/Output Capability ● SLEEP Timer ● Remote Control Capability 3 CAUTION : READ THIS BEFORE OPERATING YOUR UNIT. 1. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 2. Install this unit in a cool, dry, clean place – away from windows, heat sources, sources of excessive vibration, dust, moisture and cold. Avoid sources of humming (transformers, motors). To prevent fire or electrical shock, do not expose the unit to rain or water. 3. Never open the cabinet. If something drops into the set, contact your dealer. 4. Do not use force on switches, controls or connection wires. When moving the unit, first disconnect the power plug and the wires connected to other equipment. Never pull the wires themselves. 5. The openings on the cabinet assure proper ventilation of the unit. If these openings are obstructed, the temperature inside the cabinet will rise rapidly. Therefore, avoid placing objects against these openings, and install the unit in wellventilated condition. Make sure to allow a space of at least 20 cm behind, 20 cm on the both sides and 30 cm above the top panel of the unit. Otherwise it may not only damage the unit, but also cause fire. 6. Always set the VOLUME control to “– ∞” before starting the audio source play. Increase the volume gradually to an appropriate level after playback has been started. 7. Do not attempt to clean the unit with chemical solvents; this might damage the finish. Use a clean, dry cloth. IMPORTANT Please record the serial number of this unit in the space below. Serial No.: The serial number is located on the rear of the unit. Retain this Owner’s Manual in a safe place for future reference. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. FOR CANADIAN CUSTOMERS TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT AND FULLY INSERT. THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCECAUSING EQUIPMENT REGULATIONS. This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power. 8. Be sure to read the “TROUBLESHOOTING” section regarding common operating errors before concluding that the unit is faulty. 9. When not planning to use this unit for long periods of time (ie., vacation, etc.), disconnect the AC power plug from the wall outlet. 10. To prevent lightning damage, disconnect the AC power FREQUENCY STEP switch (China and General Models only) Because the interstation frequency spacing differs in different areas, set the FREQUENCY STEP switch (located at the rear) according to the frequency spacing in your area. Before setting this switch, disconnect the AC power plug of this unit from the AC outlet. plug and disconnect the antenna cable when there is an electrical storm. 11. Grounding or polarization – Precautions should be taken so that the grounding or polarization of an appliance is not defeated. 12. AC outlet Do not connect audio equipment to the AC outlet on the rear panel if that equipment requires more power than the outlet is rated to provide. 13. Voltage Selector (China and General Models only) The voltage selector on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply. Voltages are 110/120/220/240 V AC, 50/60 Hz. WARNING Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise this unit may be damaged. IF THIS UNIT FAILS TO TURN ON WHEN THE STANDBY/ON SWITCH IS PRESSED The IMPEDANCE SELECTOR switch may not be set to either end closely. If so, set the switch to either end closely. IMPEDANCE SELECTOR (U.S.A. model) IMPEDANCE SELECTOR SET BEFORE POWER ON REAR 6ΩMIN. /SPEAKER CENTER SINGLE:6ΩMIN. /SPEAKER DUAL:3ΩMIN. /SPEAKER MAIN A OR B:4ΩMIN. /SPEAKER A B:8ΩMIN. /SPEAKER REAR 8ΩMIN. /SPEAKER CENTER SINGLE:8ΩMIN. /SPEAKER DUAL:4ΩMIN. /SPEAKER MAIN A OR B:8ΩMIN. /SPEAKER A B:16ΩMIN. /SPEAKER 4 Battery installation Remote control transmitter operation range RX-V493 2 English NOTES ABOUT THE REMOTE CONTROL TRANSMITTER RX-V393 l6 l6 20 20 l2 28 4 2 60 l2 28 8 40 8 4 40 2 60 0 0 –dB –dB 1 3 Remote control sensor Within approximately 6 m (19.7 feet) 30° 30° Battery replacement If you find that the remote control transmitter must be used closer to the main unit, the batteries are weak. Replace both batteries with new ones. Notes ● Use only AA, R6, UM-3 batteries for replacement. ● Be sure the polarities are correct. (See the illustration inside the battery compartment.) ● Remove the batteries if the remote control transmitter will not be used for an extended period of time. ● If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries. Notes ● There should be no large obstacles between the remote control transmitter and the main unit. ● If the remote control sensor is directly illuminated by strong lighting (especially an inverter type of fluorescent lamp etc.), it might cause the remote control transmitter not to work correctly. In this case, reposition the main unit to avoid direct lighting. 5 PROFILE OF THIS UNIT You are the proud owner of a Yamaha stereo receiver –an extremely sophisticated audio component. The Digital Sound Field Processor (DSP) built into this unit takes advantage of Yamaha’s undisputed leadership in the field of digital audio processing to bring you a whole new world of listening experiences. Follow the instructions in this manual carefully when setting up your system, and this unit will sonically transform your room into a wide range of listening environments –movie theater, concert hall, and so on. In addition, you get incredible realism from sources encoded with Dolby Surround using the built-in Dolby Pro Logic Surround Decoder. Please read this operation manual carefully and store it in a safe place for later reference. Digital Sound Field Processing What is it that makes live music so good? Today’s advanced sound reproduction technology lets you get extremely close to the sound of a live performance, but chances are you’ll still notice something missing: the acoustic environment of the live concert hall. Extensive research into the exact nature of the sonic reflections that create the ambience of a large hall has made it possible for Yamaha engineers to bring you this same sound in your own listening room, so you’ll feel all the sound of a live concert. Furthermore, our technicians, armed with sophisticated measuring equipment, have even made it possible to capture the acoustics of a variety of venues such as an actual concert hall, theater, etc. to allow you to accurately recreate one of several actual live performance environments, all in your own home. Dolby Pro Logic Surround This unit employs a Dolby Pro Logic Surround decoder similar to professional Dolby Stereo decoders used in many movie theaters. By using the Dolby Pro Logic Surround decoder, you can experience the dramatic realism and impact of Dolby Surround movie theater sound in your own home. Dolby Pro Logic employs a four channel five speaker system. The Pro Logic Surround system divides the input signal into four levels: the left and right main channels, the center channel (used for dialog), and the rear surround sound channels (used for sound effects, background noise, and other ambient noises). The center channel allows listeners seated in even less-than-ideal positions to hear the dialog originating from the action on the screen while experiencing good stereo imaging. Dolby Surround is encoded on the sound track of pre-recorded video tapes, laser discs, and some TV/cable broadcasts. When you play a source encoded with Dolby Surround on this unit, the Dolby Pro Logic Surround decoder decodes the signal and distributes the surround-sound effects. This Dolby Pro Logic Surround Decoder employs a digital signal processing system. This system improves the stability of sound at each channel and minimizes crosstalk between channels, so that positioning of sounds around the room is more accurate compared with conventional analog signal processing systems. In addition, this unit features a built-in automatic input balance control. This always assures you the best performance without manual adjustment. Manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby”, “AC-3”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. Dolby Pro Logic Surround + DSP Dolby Surround sound system shows its full ability in a large movie theater, because movie sounds are originally designed to be reproduced in a large movie theater using many speakers. It is difficult to create a sound environment similar to that of a movie theater in your listening room, because the room size, materials of inside walls, the number of speakers, etc. of your listening room is much different from those of a movie theater. Yamaha DSP technology made it possible to present you with nearly the same sound experience as that of a large movie theater in your listening room by compensating for lack of presence and dynamics in your listening room with its original digital sound fields combined with Dolby Surround sound field. 6 The combination of Dolby Pro Logic Surround and DSP is used on the sound field program “ PRO LOGIC ENHANCED”. CINEMA DSP The YAMAHA “CINEMA DSP” logo indicates these programs are created by the combination of Dolby Pro Logic and YAMAHA DSP technology. English SPEAKER SETUP SPEAKERS TO BE USED This unit is designed to provide the best sound-field quality with a 5 speaker configuration. The most effective speakers to use with this unit are main speakers, rear speakers and a center speaker. You may omit the center speaker. (Refer to the “4-Speaker Configuration” shown below.) The main speakers are used for the main source sound plus the effect sounds. They will probably be the speakers from your present stereo system. The rear speakers are used for the effect and surround sounds, and the center speaker is for the center sounds (dialog etc.) within programs encoded with Dolby Surround. The center speaker needs to be equal in power to the main speakers, although the rear speakers should not be equal. However, all the speakers should have high enough power handling to accept the maximum output of this unit. SPEAKER CONFIGURATION 5-Speaker Configuration 4-Speaker Configuration This configuration is the most effective and recommended one. In this configuration, the center speaker is necessary as well as the rear speakers. If the program DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED is selected, conversations will be output from the center speaker and the ambience will be excellent. • Set the center channel mode to the “NORMAL” or “WIDE” position. (For details, refer to page 23.) The center speaker is not used in this configuration. If the program DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED is selected, the center sound is output from the left and the right main speakers. However, the sound effect of other programs can be the same as that of the 5-speaker configuration. • Be sure to set the center channel mode to the “PHANTOM” position. (For details, refer to page 23.) Front Main L Center FrontRR Main Front Main L Dialogue Dialogue Surround sound Surround sound Rear L Rear R Rear L Main FrontRR Rear R SPEAKER PLACEMENT The recommended speaker configuration, the 5-speaker configuration, will require two speaker pairs: main speakers (your normal stereo speakers), and rear speakers, plus a center speaker. When you place these speakers, refer to the following. Main: In normal position. (The position of your present stereo speaker system.) Rear: Behind your listening position, facing slightly inward. Nearly 1.8m (approx. 6 feet) up from the floor. Center: Precisely between the main speakers. (To avoid interference with TV sets, use a magnetically shielded speaker.) Front R Main R Center Main FrontLL TV set Rear R Rear L 7 CONNECTIONS Never plug in this unit and other components until all connections are completed. CONNECTIONS WITH OTHER COMPONENTS When making connections between this unit and other components, be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit. * If you have YAMAHA components numbered as 1, 2, 3, etc. on the rear panel, connections can be made easily by making sure to connect the output (or input) terminals of each component to the same-numbered terminals of this unit. RX-V493 VIDEO OUT AUDIO IN VIDEO IN VIDEO OUT AUDIO OUT VIDEO IN 2 TV/Satellite tuner Video cassette recorder * AUDIO OUT Monitor TV GND OUTPUT Turntable (U.S.A. model) IMPEDANCE SELECTOR DVD/LD TV/DBS 75Ω UNBAL. R MAIN L R SURROUND L CENTER SUB WOOFER SET BEFORE POWER ON 6CH DISCRETE INPUT OUTPUT CENTER REAR REAR (SURROUND) MAIN A OR B:4ΩMIN. /SPEAKER A B:8ΩMIN. /SPEAKER GND REAR MONITOR OUT DVD/LD IN VCR OUT 8ΩMIN. /SPEAKER CENTER SINGLE:8ΩMIN. /SPEAKER DUAL:4ΩMIN. /SPEAKER VIDEO SIGNAL FM ANT 6ΩMIN. /SPEAKER CENTER SINGLE:6ΩMIN. /SPEAKER DUAL:3ΩMIN. /SPEAKER MAIN A OR B:8ΩMIN. /SPEAKER A B:16ΩMIN. /SPEAKER TV/DBS 1 SUB WOOFER GND AM ANT * A PHONO TAPE TAPE REC /MD OUT PB 3 DVD/LD IN VCR OUT TV/DBS 4 B MAIN CD 1 2 ** , 8 : See the next page. AUDIO OUT SPEAKERS VIDEO OUT LINE IN LINE OUT Tape deck, MD recorder, etc. I20V 60Hz I00W MAX. TOTAL SWITCHED SEE INSTRUCTION MANUAL FOR CORRECT SETTING. LD player, DVD player, etc. AC OUTLETS OUTPUT 1 AUDIO SIGNAL CD player To AC outlet English RX-V393 Monitor TV * AUDIO IN VIDEO IN VIDEO OUT VIDEO IN 2 AUDIO OUT Video cassette recorder GND OUTPUT Turntable (U.S.A. model) IMPEDANCE SELECTOR VIDEO 75Ω UNBAL. R SURROUND L R MAIN L CENTER SUB WOOFER SET BEFORE POWER ON 6CH DISCRETE INPUT OUTPUT CENTER REAR REAR (SURROUND) MAIN A OR B:4ΩMIN. /SPEAKER A B:8ΩMIN. /SPEAKER GND REAR MONITOR OUT VIDEO 8ΩMIN. /SPEAKER CENTER SINGLE:8ΩMIN. /SPEAKER DUAL:4ΩMIN. /SPEAKER VIDEO SIGNAL FM ANT 6ΩMIN. /SPEAKER CENTER SINGLE:6ΩMIN. /SPEAKER DUAL:3ΩMIN. /SPEAKER MAIN A OR B:8ΩMIN. /SPEAKER A B:16ΩMIN. /SPEAKER IN VCR OUT 1 * SUB WOOFER GND AM ANT A PHONO VIDEO TAPE TAPE REC /MD OUT PB 3 IN VCR OUT 4 B MAIN 1 CD SPEAKERS AC OUTLETS OUTPUT AUDIO OUT VIDEO OUT LINE IN LINE OUT Tape deck, MD recorder, etc. I20V 60Hz I00W MAX. TOTAL SWITCHED SEE INSTRUCTION MANUAL FOR CORRECT SETTING. AUDIO SIGNAL LD player, DVD player, etc. To AC outlet CD player 1 , 2 ** 1 * : See below. 2 * AC OUTLET(S) (SWITCHED) GND terminal (For turntable use) Except Australia model.......................2 SWITCHED OUTLETS Australia model .....................................1 SWITCHED OUTLET Connecting the ground wire of the turntable to the GND terminal will normally minimize hum, but in some cases better results may be obtained with the ground wire disconnected. Use these to connect the power cords from your components to this unit. The power to the SWITCHED outlets is controlled by this unit’s STANDBY/ON switch or the provided remote control transmitter’s POWER /I key. These outlets will supply power to any component whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to the SWITCHED AC OUTLET(S) is 100 watts. 9 Connecting with a Dolby Digital (AC-3) Decoder If you have a Dolby Digital (AC-3) Decoder unit or an LD player etc. which incorporates a Dolby Digital (AC-3) Decoder, its discrete outputs can be connected to this unit. RX-V493 6CH DISCRETE OUTPUT MAIN CENTER SURROUND Dolby Digital (AC-3) Decoder unit DIGITAL IN SUB WOOFER DVD/LD TV/DBS 75Ω UNBAL. R MAIN L R SURROUND L CENTER SUB WOOFER 6CH DISCRETE INPUT DIGITAL OUT GND VIDEO SIGNAL FM ANT MONITOR OUT DVD/LD IN VCR OUT TV/DBS DVD/LD IN VCR OUT TV/DBS RF Demodulator GND AM ANT PHONO TAPE TAPE REC PB /MD OUT 3 AC-3 RF IN 4 1 CD AUDIO SIGNAL AC-3 RF OUT VIDEO OUT AUDIO OUT Laserdisc player with AC-3 RF output or another unit with AC-3 RF output Notes for RX-V493 The laserdisc player (or another unit) must be also connected to the DVD/LD (or TV/DBS) AUDIO SIGNAL input terminals of this unit for playing a source with the Dolby Pro Logic Surround decoded or in normal stereo (or monaural). • The discrete signals input to this unit cannot be recorded by a tape deck, MD recorder or VCR. To record a source played on the laserdisc player (or another unit), it must be connected to the DVD/LD (or TV/DBS) AUDIO/VIDEO SIGNAL input terminals of this unit. • 10 • If you made no connection to the SUBWOOFER input terminal of this unit or you will not use a subwoofer, you should make a setting for distributing signals at the LFE channel to the right and left MAIN output terminals on the Dolby Digital (AC-3) Decoder unit. For details, refer to the owner’s manual for the Dolby Digital (AC-3) Decoder unit. English RX-V393 6CH DISCRETE OUTPUT MAIN CENTER SURROUND Dolby Digital (AC-3) Decoder unit DIGITAL IN SUB WOOFER VIDEO 75Ω UNBAL. R MAIN L R SURROUND L CENTER SUB WOOFER 6CH DISCRETE INPUT DIGITAL OUT GND VIDEO SIGNAL FM ANT MONITOR OUT VIDEO IN VCR OUT VIDEO IN VCR OUT RF Demodulator GND AM ANT PHONO TAPE TAPE REC PB /MD OUT 3 AC-3 RF IN 4 1 CD AUDIO SIGNAL AC-3 RF OUT VIDEO OUT AUDIO OUT Laserdisc player with AC-3 RF output or another unit with AC-3 RF output Notes for RX-V393 • The laserdisc player (or another unit) must be also connected to the VIDEO AUDIO SIGNAL input terminals of this unit for playing a source with the Dolby Pro Logic Surround decoded or in normal stereo (or monaural). • The discrete signals input to this unit cannot be recorded by a tape deck, MD recorder or VCR. To record a source played on the laserdisc player (or another unit), it must be connected to the VIDEO AUDIO/VIDEO SIGNAL input terminals of this unit. • If you made no connection to the SUBWOOFER input terminal of this unit or you will not use a subwoofer, you should make a setting for distributing signals at the LFE channel to the right and left MAIN output terminals on the Dolby Digital (AC-3) Decoder unit. For details, refer to the owner’s manual for the Dolby Digital (AC-3) Decoder unit. 11 CONNECTING SPEAKERS Subwoofer system Rear speaker Rear speaker Left Right Center speaker (U.S.A. model) IMPEDANCE SELECTOR SET BEFORE POWER ON OUTPUT CENTER REAR REAR 6ΩMIN. /SPEAKER CENTER SINGLE:6ΩMIN. /SPEAKER DUAL:3ΩMIN. /SPEAKER REAR (SURROUND) MAIN A OR B:4ΩMIN. /SPEAKER A B:8ΩMIN. /SPEAKER 8ΩMIN. /SPEAKER REAR CENTER SINGLE:8ΩMIN. /SPEAKER DUAL:4ΩMIN. /SPEAKER CENTER MAIN A OR B:8ΩMIN. /SPEAKER A B:16ΩMIN. /SPEAKER C D DUAL SUB WOOFER SINGLE Main speakers B A Right Left B Left Right MAIN CAUTION SEE INSTRUCTION MANUAL FOR CORRECT SETTING. SPEAKERS Main speakers A Note Note on center speaker connection: Use speakers with the specified impedance shown on the rear of this unit. One or two center speakers can be connected to this unit. If you cannot place the center speaker on or under the TV, it is recommended to use two center speakers and place them on both sides of the TV to orient the center sound at the center position. For connecting two center speakers, follow the method shown below. Note on main speaker connections: One or two speaker systems can be connected to this unit. If you use only one speaker system, connect it to either the SPEAKERS A or B terminals. Note on a subwoofer connection: You may wish to add a subwoofer to reinforce low frequencies or to output low bass sound from the subwoofer channel when reproducing discrete signals. Connect the SUBWOOFER OUTPUT terminal of this unit to the INPUT terminal of the subwoofer amplifier, and connect the speaker terminals of the subwoofer amplifier to the subwoofer. With some subwoofers, including the Yamaha Active Servo Processing Subwoofer System, the amplifier and subwoofer are in the same unit. REAR CENTER C SINGLE Center speaker 12 D DUAL Center speaker English How to Connect: Connect the SPEAKERS terminals to your speakers with wire of the proper gauge, cut as short as possible. If the connections are faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is the + and – markings are observed. If these wires are reversed, the sound will be unnatural and lack bass. Caution Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could damage this unit and/or speakers. For connecting to the MAIN SPEAKERS terminals Red: positive (+) Black: negative (–) 2 1 3 For connecting to the REAR and CENTER SPEAKERS terminals Red: positive (+) Black: negative (–) ➀ Unscrew the knob. ➁ Insert the bare wire. [Remove approx. 5mm (1/4”) insulation from the speaker wires.] ➂ Tighten the knob and secure the wire. <U.S.A., Canada, China and General models only> ➀ Press the tab. ➁ Insert the bare wire. ➀ ➂ [Remove approx. 5mm (1/4”) insulation from the speaker wires.] ➂ Release the tab and secure the wire. ➁ Banana Plug connections are also possible. Simply insert the Banana Plug connector into the corresponding terminal. 13 OUTPUT terminals (for driving speakers with external amplifiers) SUBWOOFER OUTPUT terminal OUTPUT CENTER REAR (SURROUND) This terminal is for connecting with the input terminal of an amplifier for driving a subwoofer. When the input signals to this unit are in normal 2-channel stereo, this terminal outputs only frequencies below 150 Hz from the main and center channels. When discrete signals are input to this unit and are selected as the input source, this terminal outputs signals from the subwoofer channel. SUB WOOFER REAR (SURROUND) OUTPUT terminals CENTER OUTPUT terminal This terminal is for center channel line output. There is no connection to this terminal when you use the built-in amplifier. However, if you drive a center speaker with an external power amplifier, connect the input terminal of the external amplifier to this terminal. These terminals are for rear channel line output. There is no connection to these terminals when you use the built-in amplifier. However, if you drive rear speakers with an external stereo power amplifier, connect the input terminals of the external amplifier (MAIN IN or AUX terminals of a power amplifier or an integrated amplifier) to these terminals. Note Output level of signals from these terminals are adjusted by the use of VOLUME control on the front panel or VOLUME keys on the remote control transmitter. IMPEDANCE SELECTOR switch Be sure to switch this only when the power to this unit is not on. Select the position whose requirements your speaker system meets. WARNING Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise this unit may be damaged. (Upper position) Rear: The impedance of each speaker must be 6Ω or higher. Center: If you use one center speaker, the impedance of the speaker must be 6Ω or higher. If you use two center speakers, the impedance of each speaker must be 3Ω or higher. Main: IF THIS UNIT FAILS TO TURN ON WHEN THE STANDBY/ON SWITCH IS PRESSED The IMPEDANCE SELECTOR switch may not be set to either end closely. If so, set the switch to either end closely. If you use one pair of main speakers, the impedance of each speaker must be 4Ω or higher. If you use two pairs of main speakers, the impedance of each speaker must be 8Ω or higher. (Lower position) IMPEDANCE SELECTOR Rear: SET BEFORE POWER ON REAR 6ΩMIN. /SPEAKER The impedance of each speaker must be 8Ω or higher. CENTER SINGLE:6ΩMIN. /SPEAKER DUAL:3ΩMIN. /SPEAKER MAIN A OR B:4ΩMIN. /SPEAKER A B:8ΩMIN. /SPEAKER REAR 8ΩMIN. /SPEAKER CENTER SINGLE:8ΩMIN. /SPEAKER DUAL:4ΩMIN. /SPEAKER MAIN A OR B:8ΩMIN. /SPEAKER A B:16ΩMIN. /SPEAKER (U.S.A. model) 14 Center: If you use one center speaker, the impedance of the speaker must be 8Ω or higher. If you use two center speakers, the impedance of each speaker must be 4Ω or higher. Main: <Except Canada model> If you use one pair of main speakers, the impedance of each speaker must be 8Ω or higher. If you use two pairs of main speakers, the impedance of each speaker must be 16Ω or higher. <For Canada model only> The impedance of each speaker must be 8Ω or higher. English ANTENNA CONNECTIONS ● ● Each antenna should be connected to the designated terminals correctly, referring to the following diagram. Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may result in improvement. Outdoor FM antenna Outdoor AM antenna Indoor FM antenna (included) AM loop antenna (included) 75-ohm/300-ohm antenna adapter 75Ω UNBAL. FM ANT 75-ohm coaxial cable GND AM ANT 75-ohm/300-ohm antenna adapter 300-ohm feeder Ground Connecting the AM loop antenna 1 2 ➀ ➂ ➁ 3 Orient so that the best reception is obtained. * The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall. * The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit. GND terminal For maximum safety and minimum interference, connect the GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth. Notes ● When connecting the indoor FM antenna, insert its connector into the FM ANT terminal firmly. ● If you need an outdoor FM antenna to improve FM reception quality, either 300-ohm feeder or coaxial cable may be used. In locations troubled by electrical interference, coaxial cable is preferable. 15 CONTROLS AND THEIR FUNCTIONS FRONT PANEL RX-V493 1 2 3 NATURAL SOUND AV RECEIVER 4 CINEMA DSP RX–V493 6 7 5 PRO LOGIC ENHANCED CONCERT VIDEO DISCO ROCK CONCERT CONCERT HALL MONO MOVIE STADIUM EFFECT VOLUME l6 VCR TV/DBS 20 DVD/LD l2 28 8 STANDBY/ON TUNER A/B/C/D/E 1 2 3 4 5 6 7 TAPE/MD MON 2CH/6CH PHONO CD 4 40 2 60 8 0 –dB PHONES BASS 0 l SPEAKERS A 2 2 3 ON 3 4 5 2 FM/AM 3 4 5 DELAY/CENTER CENTER /REAR/SWFR MODE MEMORY EDIT TUNING MODE TIME/LEVEL 4 L5 B DOWN TUNING UP 2 3 4 5 A BALANCE 0 l l 2 3 4 5 0 2 3 4 OFF 8 9 TREBLE 0 l l l B 5R MAN'L/AUTO FM C AUTO/MAN'L MONO D EF H G IJ RX-V393 2 1 3 NATURAL SOUND AV RECEIVER 4 7 CINEMA DSP RX–V393 VOLUME l6 TAPE/MD MONITOR VCR 20 VIDEO l2 28 8 60 2 STANDBY/ON 2CH/6CH TUNER A/B/C/D/E 1 2 3 4 5 6 7 PHONO CD 4 40 8 0 –dB PHONES BASS 0 l l SPEAKERS A B 2 2 3 ON 4 5 8 9 16 0 A 2 3 4 OFF TREBLE 0 l l 2 3 3 4 5 4 5 B BALANCE 0 l l 5 2 FM/AM DOWN TUNING UP EFFECT CENTER MODE CENTER LEVEL REAR LEVEL 2 3 3 4 MEMORY EDIT TUNING MODE PROGRAM 4 L5 5R C 0 MAN'L/AUTO FM l0 0 l0 AUTO/MAN'L MONO D EF H K J G6 L M Standby mode In this state, this unit consumes a very small quantity of power to receive infrared-signals from the remote control transmitter. 8 PHONES jack When you listen with headphones, connect the headphones to the PHONES jack. You can listen to the sound to be output from the main speakers through headphones. When listening with headphones privately, set both the SPEAKERS A and B switches to the OFF position and switch off the digital sound field processor (so that no DSP program name is illuminated on the display) by pressing the EFFECT button. 2 Remote control sensor Receives signals from the remote control transmitter. English 1 STANDBY/ON switch Press this switch to turn the power to this unit on. Press it again to turn this unit into the standby mode. PHONES 3 Display panel Shows various information. (For details, refer to page 19.) 4 Input selector buttons Select a program source to listen to or watch. When a button is pressed, the name of selected source appears on the display. RX-V493 only 9 SPEAKERS switches When the TV/DBS or DVD/LD input source is selected, pressing the same button (TV/DBS or DVD/LD) switches the input signals between 2 channel stereo signals and 6 channel discrete signals. When switched to “6ch”, discrete signals from the unit connected to the 6CH DISCRETE INPUT DVD/LD TV/DBS terminals of this unit are selected as the input signals. Set the switch A or B (or both A and B) for the main speaker system (connected to this unit) you will use to the ON position. Set the switch for the main speaker system you will not use to the OFF position. 0 A/B/C/D/E button RX-V393 only Press this button to select a desired group (A–E) of preset stations. When the VIDEO input source is selected, pressing the same button (VIDEO) switches the input signals between 2 channel stereo signals and 6 channel discrete signals. When switched to “6ch”, discrete signals from the unit connected to the 6CH DISCRETE INPUT VIDEO terminals of this unit are selected as the input signals. 5 DSP program selector buttons RX-V493 only Select a DSP program. When a button is pressed, the name of selected program lights up on the display. 6 EFFECT button Switches on/off the digital sound field processor (including the Dolby Pro Logic Surround decoder). 7 VOLUME control Used to raise or lower the volume level. A Preset station number selector buttons Select a preset station number (1 to 8). B Tone controls These controls are effective only for the sound from the main speakers. BASS Used to increase or decrease the low frequency response. The 0 position produces flat response. TREBLE Used to increase or decrease the high frequency response. The 0 position produces flat response. C BALANCE control Adjusts the balance of the output volume to the left and right speakers to compensate for sound imbalance caused by speaker location or listening room conditions. D FM/AM button Press this button to switch the reception band to FM or AM. 17 E MEMORY (MAN’L/AUTO FM) button When this button is pressed, the “MEMORY” indicator flashes for about 5 seconds. During this period, select a desired preset station number by pressing the corresponding preset station number selector button to enter the displayed station into the memory. When this button is pressed and held for about 3 seconds, the automatic preset tuning begins. (For details, refer to page 31.) F EDIT button This button is used to exchange the places of two preset stations with each other. G TUNING DOWN/UP button Used for tuning. Press the “UP” side to tune in to higher frequencies, and press the “DOWN” side to tune in to lower frequencies. H TUNING MODE (AUTO/MAN’L MONO) button Press this button to switch the tuning mode to automatic or manual. To select the automatic tuning mode, press this button so that the “AUTO” indicator lights up on the display. To select the manual tuning mode, press this button so that the “AUTO” indicator goes off. I DELAY/CENTER/REAR/SWFR and TIME/LEVEL +/– buttons RX-V493 only Adjust the delay time (DELAY), the center channel output level (CENTER), the rear channel output level (REAR) and the output level to the SUBWOOFER OUTPUT terminal (SWFR). Select the item which you want to adjust by pressing the DELAY/CENTER/REAR/SWFR button and adjust its time or level by pressing the TIME/LEVEL +/– button. J CENTER MODE button Selects a center channel output mode (NORMAL, WIDE or PHANTOM). (For details, refer to page 23.) K PROGRAM selector button RX-V393 only When the built-in digital sound field processor (including the Dolby Pro Logic Surround decoder) is on, this button changes the currently selected DSP program whenever the right or left side of this button is pressed. L CENTER LEVEL control RX-V393 only Adjusts the sound output level of the center speaker. M REAR LEVEL control RX-V393 only Adjusts the sound output level of the rear speakers. 18 English DISPLAY PANEL 1 2 3 4 PRESET 5 6 SLEEP ms dB STEREO NORM WIDE PHANTOM l00 0 20 MHz EFFECT OFF PRO LOGIC CONCERT MONO DISCO ROCK CONCERT ENHANCED VIDEO MOVIE STADIUM CONCERT HALL kHz MEMORY AUTO 7 TAPE MON 8 9 1 Multi-information display Displays various information, for example station frequency, preset station number and name of selected input source. 2 STEREO indicator Lights up when an FM stereo broadcast with sufficient signal strength is received. 3 Signal-level meter Indicates the signal level of the received station. If multipath interference is detected, the indication decreases. 4 SLEEP indicator Lights up while the built-in SLEEP timer is functioning. 5 Center channel mode indicators The name of a selected center channel mode lights up only when a program which uses the Dolby Pro Logic Surround decoder is selected. 0 7 MEMORY indicator When the MEMORY button is pressed, this indicator flashes for about 5 seconds. During this period, the displayed station can be programmed to the memory by using the A/B/C/D/E button and the preset station number selector buttons. 8 AUTO indicator Lights up when this unit is in the automatic tuning mode. 9 TAPE MON indicator Lights up when the tape deck (or MD recorder etc.) is selected as the input source by pressing the TAPE/MD MONITOR (MON) button. 0 DSP program indicators The name of a selected DSP program lights up when the builtin digital sound field processor and/or the Dolby Pro Logic Surround decoder is on. 6 EFFECT OFF indicator Lights up if neither the digital sound field processor nor the Dolby Pro Logic Surround decoder is on. In this state, sound output is 2-channel stereo. 19 REMOTE CONTROL TRANSMITTER The remote control transmitter provided with this unit is designed to control all the most commonly used functions of this unit. If the CD player and tape deck connected to this unit are YAMAHA components designed for remote control compatibility, then this remote control transmitter will also control various functions of each component. RX-V393 RX-V493 9 1 TIME/ LEVEL – DELAY/CENTER + /REAR/SWFR TEST PROGRAM PROLOGIC ENHANCED VCR EFFECT ON/OFF 8 7 9 1 – DELAY TIME + PROGRAM TV/DBS DVD/LD TEST PROLOGIC ENHANCED VCR DIR B REC/PAUSE 1 2 – PRESET + A/B/C/D/E DISC PLAY 2 4 20 /I DIR B REC/PAUSE 1 TAPE 6 2 PLAY A/B – PRESET + A/B/C/D/E DISC CD PLAY 2 PHONO POWER 3 DIR A TUNER 8 7 2CH /6CH PLAY A/B ON/OFF VIDEO 2CH /6CH DIR A EFFECT POWER 3 5 4 TUNER 6 CD PHONO VOLUME SLEEP TAPE /I VOLUME SLEEP 5 1 DELAY/CENTER/REAR/SWFR and TIME/LEVEL +/– keys RX-V493 only Adjust the delay time (DELAY), the center channel output level (CENTER), the rear channel output level (REAR) and the output level to the SUBWOOFER OUTPUT terminal (SWFR). Select the item which you want to adjust by pressing the DELAY/CENTER/REAR/SWFR key and adjust its time or level by pressing the TIME/LEVEL +/– key. (For details, refer to page 28, 35 and 36.) DELAY TIME +/– key RX-V393 only 7 Program selector keys PROGRAM: When the built-in digital sound field processor (including the Dolby Pro Logic Surround decoder) is on, this key changes the currently selected DSP program whenever the right or left side of this key is pressed. PROLOGIC: Directly selects the PRO LOGIC program. ENHANCED: Directly selects the PRO LOGIC ENHANCED program. 8 EFFECT ON/OFF key Switches on/off the digital sound field processor (including the Dolby Pro Logic Surround decoder). Adjusts the delay time, or the time difference between the begining of source sound and the begining of effect sound. (For details, refer to page 36.) 9 TEST key 2 Tuner keys Used for speaker balance adjustment. (For details, refer to page 22–24.) Controls tuner. +: Selects higher preset station number. –: Selects lower preset station number. A/B/C/D/E: Selects the group (A – E) of preset station numbers. 3 SLEEP timer key This key is used to turn the built-in SLEEP timer on and off, and to set the SLEEP time. (For details, refer to page 37.) 4 POWER /I key Turns the power to this unit on and turns this unit into the standby mode alternately. 5 VOLUME +/– keys Turns the volume level up/down. English For Control of This Unit For Other Component Control Identify the remote control transmitter keys with your component’s keys. If these keys are identical, their functions will be the same. On each key function, refer to the corresponding instruction on your component’s manual. 1 Tape deck keys Controls tape deck. * DIR A, B and A/B are applicable only to double cassette tape deck. * For a single cassette deck with automatic reverse function, pressing DIR A will reverse the direction of tape running. 6 Input selector keys Selects input source. 2 CD player keys RX-V493 only Controls compact disc player. * DISC is applicable only to compact disc changer. When the TV/DBS or DVD/LD input source is selected, pressing the same key (TV/DBS or DVD/LD) switches the input signals between 2 channel stereo signals and 6 channel discrete signals. When switched to “6ch”, discrete signals from the unit connected to the 6CH DISCRETE INPUT DVD/LD TV/DBS terminals of this unit are selected as the input signals. RX-V393 only When the VIDEO input source is selected, pressing the same key (VIDEO) switches the input signals between 2 channel stereo signals and 6 channel discrete signals. When switched to “6ch”, discrete signals from the unit connected to the 6CH DISCRETE INPUT VIDEO terminals of this unit are selected as the input signals. 21 SPEAKER BALANCE ADJUSTMENT This procedure lets you adjust the sound output level balance between the main, center, and rear speakers using the built-in test tone generator. When this adjustment is performed, the sound output level heard at the listening position will be the same from each speaker. This is important for the best performance of the digital sound field processor and the Dolby Pro Logic Surround decoder. RX-V493 1 2 5 TIME/ LEVEL – + DELAY/CENTER /REAR/SWFR TEST PROGRAM l6 20 l2 28 RX-V393 PROLOGIC ENHANCED 5 – DELAY TIME + EFFECT ON/OFF PROGRAM TEST EFFECT PROLOGIC ENHANCED ON/OFF 8 VCR TV/DBS DVD/LD 4 40 VCR VIDEO 2CH /6CH 2CH /6CH 2 60 0 DIR A DIR B REC/PAUSE – + PLAY DIR A DIR B REC/PAUSE – + PLAY –dB A/B PRESET A/B/C/D/E DISC 3 TAPE A/B TUNER PLAY PRESET CD A/B/C/D/E DISC PLAY PHONO 4 POWER /I 3 VOLUME l6 20 CD PHONO VOLUME POWER SLEEP 1 TAPE TUNER /I VOLUME SLEEP Select the main speakers to be used. l2 SPEAKERS 28 8 A B 4 40 ON OFF 2 60 0 –dB Set to the “∞” position. 2 * If you use two main speaker systems, press both the A and B switches. 4 Turn the power on. BASS 0 l TREBLE 0 l l l 2 2 3 3 4 4 5 STANDBY/ON 5 2 BALANCE 0 l l 2 3 3 4 4 5 5 2 2 3 3 4 4 L5 Set to the “0” position. 5 22 TEST 5R TIME/ LEVEL – + RX-V393 DELAY/CENTER /REAR/SWFR TEST PROGRAM PROLOGIC ENHANCED VCR EFFECT – DELAY TIME + ON/OFF PROGRAM TEST 8 DIR A DIR B REC/PAUSE – + ON/OFF VIDEO 2CH /6CH 2CH /6CH l2 EFFECT PROLOGIC ENHANCED VCR TV/DBS DVD/LD l6 20 28 English RX-V493 PLAY DIR A DIR B REC/PAUSE – + PLAY 4 40 TAPE A/B 2 60 A/B TAPE 0 –dB PRESET A/B/C/D/E TUNER PLAY DISC PRESET A/B/C/D/E DISC CD PLAY 6 8 /I POWER VOLUME /I 7 6 Select the center channel output mode suitable for your speaker configuration. (Refer to “SPEAKER CONFIGURATION” on page 7.) 7 7 Turn up the volume. VOLUME l6 20 l2 28 CENTER MODE VOLUME SLEEP SLEEP 7 CD PHONO PHONO POWER TUNER NORMAL 8 4 40 2 60 WIDE 0 –dB PHANTOM On the feature of each mode, refer to the “Note” shown below. You will hear a test tone (like pink noise) from the left main speaker, then the center speaker, then the right main speaker, and then the rear speakers, for about two seconds each. The display changes as shown below. Center Main (L) Note In step 6, when you select a center channel output mode, note the following. For 5 speaker configuration) NORMAL: Select this mode when you use a center speaker that is smaller than the main speakers. In this mode, the bass tone will be output from the main speakers. WIDE: Select this mode when you use the center speaker approximately same sized as the main speakers. For 4 speaker configuration) PHANTOM: Select this mode when you do not use the center speaker. The center sound will be output from the left and right main speakers. Rear (L and R) * 8 Main (R) The test tone from the left rear speaker and the right rear speaker will be heard at the same time. Adjust the BALANCE control so that the effect sound output level of the left main speaker and the right main speaker are the same. BALANCE 0 l l 2 2 3 3 4 4 L5 5R CONTINUED 23 RX-V493 RX-V393 10 10 9 TIME/ LEVEL – + DELAY/CENTER /REAR/SWFR TEST PROGRAM PROLOGIC ENHANCED – DELAY TIME + EFFECT ON/OFF PROGRAM TEST EFFECT ON/OFF PROLOGIC ENHANCED l6 VCR 20 TV/DBS DVD/LD 2CH /6CH DIR A A/B – PRESET + A/B/C/D/E 8 60 2 VIDEO 2CH /6CH 4 DIR A DIR B REC/PAUSE – + 0 TAPE PLAY A/B –dB TUNER PLAY DISC 28 40 PLAY DIR B REC/PAUSE VCR l2 PRESET A/B/C/D/E DISC CD PLAY /I VOLUME 9 SLEEP 9 Adjust the sound output levels of the center speaker and the rear speakers so that they become almost as same as that of the main speakers. 10 Press once or more so that “CENTER” or “REAR” appears on the display. * Select “CENTER” to adjust the output level of the center speaker, and select “REAR” to adjust the output level of the rear speakers. DELAY/CENTER /REAR/SWFR Adjust its level. * Pressing the + side raises and the – side lowers the level. TIME/ – LEVEL + RX-V393 CENTER LEVEL 0 24 l0 REAR LEVEL 0 l0 /I VOLUME TEST Disappears. Notes Once you have completed these adjustments, you can adjust whole sound level on your audio system by using the VOLUME control (or the VOLUME keys on the remote control transmitter) only. ● If you use external power amplifiers, you may also use their volume controls to achieve proper balance. ● ● b) POWER SLEEP Cancel the test tone. RX-V493 Make the adjustment of each speaker output level at your listening position with the remote control transmitter. a) CD PHONO PHONO POWER TAPE TUNER RX-V493 only In step 9, if the center channel mode is in the “PHANTOM” position, the sound output level of the center speaker cannot be adjusted. This is because in this mode, the center sound is automatically output from the left and right main speakers. English BASIC OPERATIONS TO PLAY A SOURCE 3 2 1, 6 l6 20 l2 28 8 4 40 2 60 0 –dB 4 1 7 5 VOLUME l6 20 l2 28 8 6 4 40 Play the source. (For detailed information on the tuning operation, refer to page 29.) VOLUME l6 20 28 2 60 l2 8 0 4 40 –dB Set to the “∞” position. 2 60 0 –dB 2 Adjust to the desired output level. Turn the power on. STANDBY/ON 7 3 Select the desired input source by using the input selector buttons. (For video sources, turn the TV/monitor ON.) TUNER PHONO CD * The name of the selected input source will appear on the display. 4 Select the main speakers to be used. SPEAKERS A ON B If desired, adjust the BASS, TREBLE and BALANCE controls (refer to page 28), and use the digital sound field processor. (Refer to page 34.) Notes on using the input selector buttons Note that pressing on each input selector button selects the source which is connected to the corresponding input terminals on the rear panel. ● The selection of TAPE/MD MONITOR (MON) cannot be canceled by pressing another input selector button. To cancel it, press TAPE/MD MONITOR (MON) again so that the “TAPE MON” indicator disappears from the display. When you select a button other than TAPE/MD MONITOR (MON), make sure that the “TAPE MON” indicator is not illuminated on the display. ● If you select the input selector button for a video source without canceling the selection of TAPE/MD MONITOR (MON), the playback result will be the video image from the video source and the sound from the audio tape (or MD etc.). ● Once you play a video source, its video image will not be interrupted even if the input selector button for an audio source is selected. ● OFF * If you use two main speaker systems, press both the A and B switches. When you finish using this unit Press the STANDBY/ON switch again to turn this unit into the standby mode. 25 To listen to a decoded source using Dolby Digital (AC-3) by reproducing the signals input to the 6CH DISCRETE INPUT terminals of this unit. In step 3, press the button (shown below) once or more so that “6ch” appears on the display. Discrete signals from the unit connected to the 6CH DISCRETE INPUT terminals of this unit are selected as the input signals. RX-V493 TV/DBS DVD/LD TAPE/MD MON 2CH/6CH TV/DBS DVD/LD TAPE/MD MON 2CH/6CH or To cancel listening to a decoded source using Dolby Digital (AC-3) Press the same button again or select another input source. Note for reproducing discrete signals with Dolby Digital (AC-3) decoded: 1. Your speaker system must include a center speaker. 2. Your speaker system must include a subwoofer. * Connect a subwoofer which has a built-in amplifier to the SUBWOOFER OUTPUT terminal of this unit. * You can do without using a subwoofer. If you do so, you should make a setting for distributing signals at the LFE channel to the right and left MAIN output terminals on the Dolby Digital (AC-3) Decoder unit. For details, refer to the owner’s manual for the Dolby Digital (AC-3) Decoder unit. Notes ● When you switch to the “6ch” mode, the built-in Digital Sound Field processor will not work and adjustment of delay time cannot be made. ● RX-V393 VCR VIDEO 2CH/6CH 26 Switching this unit to the “6ch” mode will input no signal to this unit if there is no connection to the 6CH DISCRETE INPUT terminals of this unit. English TO RECORD A SOURCE TO TAPE (OR MD) RX-V493 RX-V393 1 4 2 4 1 2 l6 l6 20 20 l2 28 8 4 40 4 2 60 2 60 l2 28 8 40 0 0 –dB –dB 1 TUNER 2 3 Select the source to be recorded. PHONO CD 4 Begin recording on the tape deck (or MD recorder etc.) or VCR connected to this unit. If the tape deck (or MD recorder etc.) is used for recording, you can monitor the sounds being recorded by pressing TAPE/MD MONITOR (MON) so that the “TAPE MON” indicator lights up on the display. RX-V493 Play the source and then turn the VOLUME control up to confirm the input source. (For detailed information on the tuning operations, refer to the page 29.) RX-V393 TV/DBS DVD/LD TAPE/MD MON 2CH/6CH PHONO CD TAPE/MD MONITOR VCR TUNER PHONO VOLUME l6 20 l2 28 8 4 40 2 60 0 –dB Notes The settings of DSP and the VOLUME, BASS, TREBLE and BALANCE controls have no effect on the material being recorded. ● In step 1, do not make an input source selection so that “6ch” appears on the display. Signals input to this unit’s 6CH DISCRETE INPUT terminals cannot be recorded by a tape deck, MD recorder or VCR. ● 27 Selecting the SPEAKER system Because one or two speaker systems (as main speakers) can be connected to this unit, the SPEAKERS switches allow you to select speaker system A or B, or both at once. Adjusting the BASS and TREBLE controls BASS 0 l TREBLE 0 l l l 2 SPEAKERS 2 3 A 3 4 4 5 ON 2 2 3 3 B 5 4 4 5 5 OFF BASS Adjusting the BALANCE control Adjust the balance of the output volume to the left and right speakers to compensate for sound imbalance caused by speaker location or listening room conditions. BALANCE 0 l l 2 : Turn this clockwise to increase (or counterclockwise to decrease) the low frequency response. TREBLE : Turn this clockwise to increase (or counterclockwise to decrease) the high frequency response. Note These controls are effective only for the sound from the main speakers. 2 3 3 4 4 L5 5R Note This control is effective only for the sound from the main speakers. RX-V493only only Adjusting the subwoofer output level RX-V493 If your audio system includes a subwoofer, and an amplifier driving the subwoofer (or a subwoofer system including an amplifier) is connected to the SUBWOOFER OUTPUT terminal on the rear of this unit, you can adjust the subwoofer output level on this unit. 1 Press once or more so that “SWFR” appears on the display. DELAY/CENTER /REAR/SWFR 2 By continuously pressing the “+” or “–” side of the TIME/LEVEL button, the level value changes continuously. If you feel that bass tone is insufficient, increase the level, and if you feel that bass tone is overly emphasized, decrease the level. TIME/LEVEL Adjustable Control range: MIN, –20 to 0 dB 28 English TUNING OPERATIONS Normally, if station signals are strong and there is no interference, quick automatic-search tuning (AUTOMATIC TUNING) is possible. However, if signals of the station you want to select are weak, you must tune to it manually (MANUAL TUNING). l6 20 l2 28 8 4 40 2 60 0 –dB 1 2 AUTOMATIC TUNING 1 2 MANUAL TUNING 1 Select “TUNER” as the input source. TUNER PHONO 4 3 Select “TUNER” as the input source. CD TUNER Select the reception band (FM or AM) confirming it on the display. 2 FM/AM PHONO CD Select the reception band (FM or AM) confirming it on the display. FM/AM or 3 3 TUNING MODE AUTO/MAN’L MONO 4 or Turn the “AUTO” indicator off. AUTO/MAN’L MONO AUTO DOWN TUNING UP TUNING MODE 4 Tune to a desired station manually. DOWN TUNING UP To tune to a higher frequency, press the right side once. To tune to a lower frequency, press the left side once. * If the station where tuning search stops is not the desired one, press again. * If the tuning search does not stop at the desired station (because the signals of the station are weak), change to the MANUAL TUNING method. * To continue tuning search, press and hold the button. Note If you tune to an FM station manually, it is received in monaural mode automatically to increase the signal quality. 29 PRESET TUNING MANUAL PRESET TUNING This unit can store station frequencies selected by tuning operation. With this function, you can recall any desired station by only selecting the preset station number where it is stored. Up to 40 stations (8 stations x 5 groups) can be stored. l6 20 l2 28 8 4 40 2 60 0 –dB 2, 1 4, 2 To recall a preset station To store stations 1 2 3 1 Tune to a desired station. (Refer to the previous page for tuning procedure.) Select the group of preset stations. A/B/C/D/E Select a desired group (A – E) of preset stations confirming it on the display. A/B/C/D/E 2 PRESET Select the preset station number. 1 3 2 3 4 5 6 7 8 MEMORY MEMORY MAN’L/AUTO FM Flashes on and off for about 5 seconds. 4 Select a preset station number where you want to program the station before the “MEMORY” indicator goes off from the display. 1 2 3 4 5 6 7 8 Memory back-up The memory back-up circuit prevents the programmed data from being lost even if this unit is turned into the standby mode or the power plug is disconnected from the AC outlet or the power is cut due to temporary power failure. If, however, the power is cut for more than one week, the memory may be erased. If so, it can be re-programmed by simply following the PRESET TUNING steps. STEREO PRESET MHz AUTO 0 20 l00 CONCERT HALL Shows the displayed station has been programmed to A1. * In the same way, program other stations to A2, A3 ... A8. * You can program more stations to preset station numbers on other groups in the same way by selecting other groups in step 2. 30 Notes A new setting can be programmed in place of the former one. • For presets, the setting of the reception mode (stereo or monaural) is stored along with the station frequency. • English AUTOMATIC PRESET TUNING You can also make use of an automatic preset tuning function for FM stations only. By this function, this unit performs automatic tuning and stores FM stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the manual preset tuning method on page 30. l6 20 l2 28 8 4 40 2 60 0 –dB 1 23 To store stations 1 When the automatic preset tuning is finished The display shows the frequency of the last preset station. Check the contents and the number of preset stations by following the procedure of the section “To recall a preset station” on page 30. FM/AM To recall a preset station 2 Simply follow the procedure of the section “To recall a preset station” on page 30. MEMORY PRESET MAN’L/AUTO FM MEMORY AUTO Press and hold for about 3 seconds. 3 Flashes. DOWN TUNING UP To tune to higher frequencies, press right side once. To tune to lower frequencies, press left side once. * If the TUNING button is not pressed, in a while, the automatic preset tuning begins automatically toward higher frequencies. Notes ● You can replace a preset station by another FM or AM station manually by simply following the procedure of the section “To store stations” on page 30. ● If the number of received stations is not enough to be stored up to E8, the search is finished automatically after searching all frequencies. ● With this function, only FM stations with sufficient signal strength are stored automatically. If the station you want to program is weak in signal strength, tune to it in monaural manually and program it by following the procedure of the section “To store stations” on page 30. The automatic preset tuning begins from the frequency currently displayed. Received stations are programmed to A1, A2 ... A8 sequentially. * If more than 8 stations are received, they are also programmed to the preset station numbers on other groups (B, C, D and E) in that order. If you want to store the first station received by the automatic preset tuning to a desired preset station number. If, for example, you want to store the first received station to C5, select “C5” by using the A/B/C/D/E button and the preset station number selector buttons after pressing the MEMORY button in step 2. Then press the TUNING button. The first received station is stored to C5, and next stations to C6, C7 ... sequentially. If stations are stored up to E8, the automatic preset tuning is finished automatically. 31 EXCHANGING PRESET STATIONS You can exchange the places of two preset stations with each other as shown below. l6 20 l2 28 8 4 40 2 60 0 –dB 2, 4 Example) If you want to shift the preset station on E1 to A5, and vice versa. 1 Recall the preset station on E1 (by following the method of “To recall a preset station” on page 30). 4 EDIT 2 EDIT PRESET MEMORY Flashes. 3 Next, recall the preset station on A5 by following the same method with step 1. PRESET MEMORY Shows the exchange of stations is completed. Flashes. 32 This unit incorporates a sophisticated, multi-program digital sound field processor. The processor allows you to electronically expand and change the shape of the audio sound field from both audio and video sources, creating a theater-like experience in your listening room. You can create an excellent audio sound field by selecting a suitable sound field program (this will, of course, depend on what you will be listening to), and adding desired adjustments. English USING DIGITAL SOUND FIELD PROCESSOR (DSP) In addition, this unit incorporates a Dolby Pro Logic Surround decoder for multi-channel sound reproduction of sources encoded with Dolby Surround. The operation of the Dolby Pro Logic Surround decoder can be controlled by selecting a corresponding DSP program including a combined operation of the Yamaha DSP and the Dolby Pro Logic Surround. Brief Overview of Digital Sound Field Programs The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in mind that most of these are precise digital recreations of actual acoustic environments. The data for these sound fields was recorded at actual locations using sophisticated sound field measurement equipment. Note The channel level balance between the left and right rear effect speakers may vary depending on the sound field you are listening to. This is due to the fact that most of these sound field recreations are actual acoustic environments. PROGRAM FEATURE PRO LOGIC This program is used for playback of sources encoded with Dolby Surround. The application of a sophisticated digital signal processing system reduces crosstalk and directs or steers the sound source more smoothly and precisely, as compared to conventional types. PRO LOGIC ENHANCED This program is also used for playback of sources encoded with Dolby Surround. Enhancing the “Normal” Dolby Pro Logic, the DSP technology simulates the multi-surround speaker systems of a 35 mm movie theater. This effect creates a wide surround sound field, and expands the sound stage with an improved presence image. This program is used for musical based movies, as well as drama and comedy based movies. CONCERT VIDEO This program is effective for music videos and gives excellent depth and clarity for vocals. For opera, the orchestra and stage are ideally recreated, letting you feel as if you were in an actual concert hall. MONO MOVIE This program is designed specifically to enhance mono source programs. Compared to a strictly mono setting, the sound image created in this mode is wider and slightly forward of the speaker pair, lending an immediacy to the overall sound. It is particularly effective when used with old mono movies, news broadcasts and dialog. STADIUM This program gives you long delays between direct sounds and effect sounds, and extraordinarily spacious feel of a large stadium. DISCO This program recreates the acoustic environment of a lively disco in the heart of a very lively city. The sound is dense and highly concentrated. It is also characterized by a high-energy, “immediate” sound. ROCK CONCERT This program is ideally suited for rock music. You will experience a very dynamic or lively sound field. CONCERT HALL In this program, the center will appear to be deep behind the main speakers, creating an expansive large hall ambience. Orchestra and opera music are suited for this sound field. 33 To play a source with the digital sound field processor RX-V493 RX-V393 2 TIME/ LEVEL – + DELAY/CENTER /REAR/SWFR TEST PROGRAM PROLOGIC ENHANCED VCR ON/OFF – DELAY TIME + 2 PROGRAM l6 20 VCR DIR B REC/PAUSE ON/OFF 2 VIDEO 4 2CH /6CH 2 60 DIR A 8 EFFECT 8 40 2CH /6CH l2 28 TEST PROLOGIC ENHANCED l2 28 TV/DBS DVD/LD l6 20 EFFECT DIR A PLAY DIR B REC/PAUSE PLAY 0 –dB 4 40 A/B 2 60 TAPE A/B TAPE 0 –dB – PRESET + A/B/C/D/E DISC PLAY – TUNER PRESET + A/B/C/D/E DISC CD PLAY /I VOLUME 2 Follow steps 1 – 6 shown in “BASIC OPERATIONS” on page 25. Select the desired program that is suitable for the source. RX-V493 RX-V393 a) PRO LOGIC EFFECT ENHANCED Turn the DSP on so that a program name lights up on the display. PRO LOGIC PRO LOGIC b) PROGRAM Select a desired program confirming it on the display. The selected program name is shown on the display. 3 If desired, adjust the delay time and the output level of each speaker. (For details, refer to the corresponding descriptions on page 35 and 36.) POWER 2 SLEEP 1 /I VOLUME SLEEP Notes Program selection can be made to individual input sources. Once you select a program, it is linked with the input source selected at that time. So, when you select the input source next time, the same program is automatically called. ● If you prefer to cancel the DSP, press the EFFECT button. The sound will be the normal 2-channel stereo without surround sound effect. ● When CONCERT VIDEO, MONO MOVIE, STADIUM, DISCO, ROCK CONCERT or CONCERT HALL is selected, no sound is heard from the center speaker. ● When a monaural sound source is played with DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED, no sound is heard from the main speakers and the rear speakers. Sound is heard only from the center speaker. However, if the center channel mode is in PHANTOM, the main speakers output the sound of the center channel. ● When this unit’s Dolby Pro Logic Surround decoder is used, if the main-source sound is considerably altered by overadjustment of the BASS or TREBLE control, the relationship between the center and rear channels may produce an unnatural effect. ● To select a DSP program on the remote control transmitter, first turn the DSP on so that a program name lights up on the display by pressing the EFFECT key. Next, select a desired DSP program by pressing the or side of PROGRAM key. ● PROGRAM EFFECT ON/OFF * Pressing the PROLOGIC or ENHANCED key turns the DSP on and selects the corresponding program directly. PROLOGIC 34 CD PHONO PHONO POWER TUNER ENHANCED English Adjustment of the CENTER LEVEL If desired, you can adjust the sound output level of the center speaker even if the output level is already set in “SPEAKER BALANCE ADJUSTMENT” on page 24. RX-V493 1 Notes ● This adjustment can be made only when the digital sound field program DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED is selected. ● Once the output level is adjusted, the level value will be the same in all the digital sound field programs mentioned above. Press once or more so that “CENTER” appears on the display. DELAY/CENTER /REAR/SWFR RX-V393 2 CENTER LEVEL By continuously pressing the “+” or “–” side of the TIME/LEVEL button, the level value changes continuously. The value stops changing momentarily at the preset point (0 dB). TIME/LEVEL Adjustable 0 l0 Note This adjustment is useful only when the digital sound field program DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED is selected. Control range: MIN, –20 to +10 dB Adjustment of the REAR LEVEL If desired, you can adjust the sound output level of the rear speakers even if the output level is already set in “SPEAKER BALANCE ADJUSTMENT” on page 24. Notes ● This adjustment can be made only when the built-in digital sound field processor is on. ● RX-V493 1 Once the output level is adjusted, the level value will be the same in all the digital sound field programs. Press once or more so that “REAR” appears on the display. DELAY/CENTER /REAR/SWFR RX-V393 REAR LEVEL 2 By continuously pressing the “+” or “–” side of the TIME/LEVEL button, the level value changes continuously. The value stops changing momentarily at the preset point (0 dB). 0 l0 Note If no digital sound field program is used, this adjustment is useless. TIME/LEVEL Adjustable Control range: MIN, –20 to +10 dB 35 Adjustment of DELAY TIME You can adjust the time difference between the beginning of the sound from the main speakers and the beginning of the effect sound from the rear speakers. The larger the value, the later the effect sound is generated. This adjustment can be made to all programs individually. RX-V493 1 Press once or more so that “DELAY” appears on the display. DELAY/CENTER /REAR/SWFR ms PRO LOGIC PRO LOGIC ENHANCED CONCERT VIDEO MONO MOVIE STADIUM DISCO ROCK CONCERT CONCERT HALL : from 15 to 30 milliseconds (Preset value: 20 milliseconds) : from 15 to 30 milliseconds (Preset value: 20 milliseconds) : from 1 to 100 milliseconds (Preset value: 28 milliseconds) : from 1 to 100 milliseconds (Preset value: 20 milliseconds) : from 1 to 50 milliseconds (Preset value: 45 milliseconds) : from 1 to 100 milliseconds (Preset value: 14 milliseconds) : from 1 to 100 milliseconds (Preset value: 17 milliseconds) : from 1 to 100 milliseconds (Preset value: 30 milliseconds) 2 By continuously pressing the “+” or “–” side of the TIME/LEVEL button, the value changes continuously. The value stops changing momentarily at the preset point. TIME/LEVEL ms Adjustable Notes ● When the TIME/LEVEL button is pressed, sound is momentarily interrupted. ● Adding too much delay will cause an unnatural effect with some sources. RX-V393 This adjustment can be made by only using the remote control transmitter. DELAY TIME ms Adjustable Notes ● When the DELAY TIME key is pressed, sound is momentarily interrupted. ● Adding too much delay will cause an unnatural effect with some sources. Notes RX-V493 only RX-V393 only The values of the delay time, center level, rear level and subwoofer output level you set the last time will remain memorized even when this unit is in the standby mode. However, if the power cord is kept disconnected for more than one week, these values will be automatically changed back to the original factory settings. The value of the delay time you set the last time will remain memorized even when this unit is in the standby mode. However, if the power cord is kept disconnected for more than one week, these values will be automatically changed back to the original factory settings. 36 English SETTING THE SLEEP TIMER If you use the SLEEP timer of this unit, you can make this unit turn into the standby mode. When you are going to sleep while enjoying a broadcast or other desired input source, this timer function is helpful. Notes ● The SLEEP timer can be controlled only with the remote control transmitter. ● The components on which the SLEEP timer is effective are the sources connected to the SWITCHED AC OUTLET(S) on the rear panel of this unit. To set the SLEEP time To cancel the selected SLEEP time 1 SLEEP SLEEP Press once or more to select the desired SLEEP time. Press once or more so that “SLEEP OFF” appears on the display. (It will soon disappear and the “SLEEP” indicator will go off from the display.) Note The SLEEP timer setting can also be canceled by turning this unit into the standby mode with the STANDBY/ON switch or disconnecting the power plug of this unit from the AC outlet. Indicates the SLEEP time. SLEEP CONCERT HALL Lights up. Whenever the SLEEP key is pressed, the SLEEP time will change as follows. (Minutes) 120 90 60 30 The SLEEP timer is off (OFF). (The state before the SLEEP key is pressed.) After a while, the display returns to the indication before the SLEEP timer is set. 2 The unit will be turned into the standby mode automatically at the selected SLEEP time. 37 TROUBLESHOOTING If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service center for help. SYMPTOM Amplifier REMEDY Power cord is not plugged in or is not completely inserted. Firmly plug in the power cord. The IMPEDANCE SELECTOR switch on the rear panel is not set to the upper or the lower end closely. Set the switch to the upper or the lower end closely. It happens that this unit does not work normally. There is an influence of strong external noise (lightning, excessive static electricity, etc.) or a misoperation on this unit while using this unit. Turn this unit into the standby mode and disconnect the AC power cord from the AC outlet. After about 30 seconds have passed, connect the power and operate this unit again. No sound or no picture. Incorrect output cord connections. Connect the cords properly. If the problem persists, the cords may be defective. Appropriate input source is not selected. Select an appropriate input source with the input selector buttons. The SPEAKERS switches are not set properly. Set the SPEAKERS switch which corresponds to the speakers to be used to the ON position. Speaker connections are not secure. Secure the connections. The protection circuit has been activated because of short circuit etc. Turning the unit into the standby mode and then on will reset the protection circuit. The SLEEP timer has functioned. Cancel the SLEEP timer function. Incorrect setting of the BALANCE control. Adjust it to the appropriate position. Incorrect cord connections. Connect the cords properly. If the problem persists, the cords may be defective. Incorrect cord connections. Firmly connect the audio plugs. If the problem persists, the cords may be defective. No connection from the turntable to the GND terminal. Make the GND connection between the turntable and this unit. The volume level is low while playing a record. The record is being played on a turntable with an MC cartridge. The player should be connected to the unit through the MC head amplifier. The volume level cannot be increased, or sound is distorted. The component connected to the REC OUT terminals of this unit is in the standby mode. Turn the power to the component on. No sound from the rear speakers. The sound output level to the rear speakers is set to minimum. Raise the sound output level to the rear speakers. The monaural sound source is played in DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED mode. Select another program suitable for the monaural sound source. The sound output level to the center speaker is set to minimum. Raise the sound output level to the center speaker. The center channel mode is in PHANTOM mode. Select NORMAL or WIDE. Incorrect sound field program selection. Select the appropriate program. FM stereo reception is noisy. Because of the characteristics of FM stereo broadcasts, this is limited to cases where the transmitter is too far away or the antenna input is poor. Check the antenna connections. Try using a high quality directional FM antenna. Set the TUNING MODE button to the manual tuning mode. There is distortion and clear reception cannot be obtained even with a good FM antenna. There is multipath interference. Adjust antenna placement to eliminate multipath interference. A desired station cannot be tuned in with the automatic tuning method. The station is too weak. Use the manual tuning method. Use a high quality directional FM antenna. Previously preset stations can no longer be tuned in. This unit has been unplugged for a long period. Repeat the presetting procedure. A desired station cannot be tuned in with the automatic tuning method. Weak signal or loose antenna connections. Tighten the AM loop antenna connections and rotate it for best reception. There are continuous crackling and hissing noises. Noises will result from ligtning, fluorescent lamps, motors, thermostats and other electrical equipment. Use an outdoor antenna and a ground wire. This will help somewhat but it is difficult to eliminate all noise. There are buzzing and whining noises (especially in the evening). A television set is being used nearby. Relocate this unit away from the TV. The remote control transmitter does not work. Direct sunlight or lighting (of an inverter type of fluorescent lamp etc.) is striking the remote control sensor of the main unit. Change the position of the main unit. The batteries of this remote control transmitter are too weak. Replace the batteries with new ones. This unit is in the standby mode. Turn the power to this unit on. The sound suddenly goes off. Only one side speaker outputs the sound. Sound “hums”. No sound from the center speaker. FM CAUSE The unit fails to turn on when the STANDBY/ON switch is pressed, or turns into the standby mode suddenly soon after the power is turned on. Others Remote control transmitter AM Use the manual tuning method. 38 The sound is degraded when listening with the headphones connected to the compact disc player or cassette deck that are connected with this unit. AUDIO SECTION Minimum RMS Output Power per Channel Main L, R 8 ohms, 20 Hz to 20 kHz, 0.04% THD <RX-V493> [U.S.A. and Canada models] .................................................70W+70W [Europe, Australia, China and General models] ....................................65W+65W <RX-V393>...............................50W+50W Center 8 ohms, 1 kHz, 0.04% THD <RX-V493> [U.S.A. and Canada models] ..........................................................70W [Europe, Australia, China and General models]..............................................65W <RX-V393> ........................................50W Rear L, R 8 ohms, 1 kHz, 0.04% THD ..........20W+20W Maximum Power [China and General models only] 8 ohms, 1 kHz, 10% THD Main L, R <RX-V493> ........................100W+100W <RX-V393> ............................75W+75W Center <RX-V493>....................................100W <RX-V393>......................................75W Rear L, R.......................................30W+30W Dynamic Power per Channel (by IHF Dynamic Headroom measuring method) <RX-V493> 8/6/4/2 ohms [U.S.A. and Canada models] ...................................100/120/150/175W [Europe, Australia, China and General models].........................95/115/145/165W <RX-V393> 8/6/4/2 ohms [U.S.A. and Canada models] .......................................80/95/120/140W [Europe, Australia, China and General models].........................80/100/120/135W DIN Standard Output Power per Channel [Europe model only] 4 ohms, 1 kHz, 0.7% THD <RX-V493>......................................95W <RX-V393>......................................75W Dynamic Headroom (8 ohms) [U.S.A. and Canada models only] <RX-V493> ...................................1.55 dB <RX-V393> ...................................2.04 dB IEC Power [Europe model only] 8 ohms, 1 kHz, 0.1% THD <RX-V493> ........................................80W <RX-V393> ........................................60W Power Band Width <RX-V493> 8 ohms, 30W, 0.1% THD ...........................................10 Hz to 50 kHz <RX-V393> 8 ohms, 25W, 0.1% THD ...........................................10 Hz to 50 kHz Damping Factor (SPEAKERS A) 8 ohms, 20 Hz to 20 kHz ...............80 or more Input Sensitivity/Impedance <RX-V493> PHONO MM ...................2.5 mV/47 k-ohms CD/TAPE·MD/DVD·LD/TV·DBS/VCR ......................................150 mV/47 k-ohms 6CH DISCRETE INPUT MAIN...........................150 mV/56 k-ohms CENTER.....................150 mV/40 k-ohms SURROUND...............100 mV/40 k-ohms SUBWOOFER ............150 mV/40 k-ohms <RX-V393> PHONO MM ...................2.5 mV/47 k-ohms CD/TAPE·MD/VIDEO/VCR ......................................150 mV/47 k-ohms 6CH DISCRETE INPUT MAIN...........................150 mV/56 k-ohms CENTER.....................150 mV/11 k-ohms SURROUND...............100 mV/11 k-ohms SUBWOOFER ............150 mV/40 k-ohms Maximum Input Signal <RX-V493> PHONO MM 1 kHz, 0.5% THD..........................100 mV CD/TAPE·MD/DVD·LD/TV·DBS/VCR (EFFECT OFF) 1 kHz, 0.5% THD...............................2.5V <RX-V393> PHONO MM 1 kHz, 0.5% THD..........................100 mV CD/TAPE·MD/VIDEO/VCR (EFFECT OFF) 1 kHz, 0.5% THD...............................2.5V Output Level/Impedance REC OUT........................150 mV/2.5 k-ohms CENTER OUTPUT .................2V/1.2 k-ohms REAR OUTPUT ...................1.2V/1.2 k-ohms SUBWOOFER OUTPUT (EFFECT OFF) ................................................4V/1.2 k-ohms Headphones Jack Rated Output/Impedance Output Level (8 ohms, 0.04% THD) .....0.45V Impedance .....................................330 ohms Frequency Response (20 Hz to 20 kHz) <RX-V493> CD/TAPE·MD/DVD·LD/TV·DBS/VCR ......................................................0±0.5 dB <RX-V393> CD/TAPE·MD/VIDEO/VCR ............0±0.5 dB RIAA Equalization Deviation PHONO MM ....................................0±0.5 dB English SPECIFICATIONS Total Harmonic Distortion (20 Hz to 20 kHz) <RX-V493> PHONO MM to REC OUT 1V ...................................................0.02% CD/TAPE·MD/DVD·LD/TV·DBS/VCR to SP OUT 30W/8 ohms ...................................0.03% <RX-V393> PHONO MM to REC OUT 1V ...................................................0.02% CD/TAPE·MD/VIDEO/VCR to SP OUT 30W/8 ohms ...................................0.03% Signal-to-Noise Ratio (IHF-A Network) <RX-V493> PHONO MM to REC OUT (5 mV Input Shorted)..........................80 dB CD/TAPE·MD/DVD·LD/TV·DBS/VCR to SP OUT (Shorted)..........................93 dB <RX-V393> PHONO MM to REC OUT (5 mV Input Shorted)..........................80 dB CD/TAPE·MD/VIDEO/VCR to SP OUT (Shorted) ............................................93 dB Residual Noise (IHF-A Network) MAIN L/R............................................140 µV Channel Separation (Vol. –30 dB, EFFECT OFF) <RX-V493> PHONO MM (Input Shorted, 1 kHz) .....................60 dB CD/TAPE·MD/DVD·LD/TV·DBS/VCR (Input 5.1 k-ohms Terminated, 1 kHz) ........................................................60 dB <RX-V393> PHONO MM (Input Shorted, 1 kHz) .....................60 dB CD/TAPE·MD/VIDEO/VCR (Input 5.1 k-ohms Terminated, 1 kHz) ........................................................60 dB Tone Control Characteristics BASS: Boost/cut ...............±10 dB (50 Hz) Turnover Frequency...........350 Hz TREBLE: Boost/cut .............±10 dB (20 kHz) Turnover Frequency..........3.5 kHz Gain Tracking Error (0 to –60 dB) .............3 dB VIDEO SECTION Video Signal Level ..................1 Vp-p/75 ohms Maximum Input Level ............1.5 Vp-p or more Signal-to-Noise Ratio.................50 dB or more Monitor Out Frequency Response .....................................5 Hz to 10 MHz, –3 dB 39 FM SECTION Tuning Range [U.S.A. and Canada models] ..........................................87.5 to 107.9 MHz [Europe, Australia, China and General models]..............................87.5 to 108.0 MHz 50 dB Quieting Sensitivity (IHF, 75 ohms) [U.S.A., Canada, Australia, China and General models only] Mono...............................1.55 µV (15.1 dBf) Stereo ................................21 µV (37.7 dBf) Usable Sensitivity (75 ohms) [Europe and Australia models only] DIN, Mono (S/N 26 dB)......................0.9 µV DIN, Stereo (S/N 46 dB) .....................24 µV Image Response Ratio [U.S.A., Canada, China and General models] ..............................................................45 dB [Europe and Australia models] .............80 dB IF Response Ratio [U.S.A., Canada, China and General models] ..............................................................70 dB [Europe and Australia models] .............80 dB Spurious Response Ratio.........................70 dB AM Suppression Ratio..............................55 dB Capture Ratio ..........................................1.5 dB Alternate Channel Selectivity [U.S.A., Canada, China and General models only] .......................................................85 dB Selectivity (two signals, 40 kHz Dev. ±300 kHz) [Europe and Australia models only] ...............................................................70 dB Signal-to-Noise Ratio (IHF) Mono/Stereo [U.S.A., Canada, China and General models] .....................................80 dB/75 dB (DIN-Weighted, 40 kHz Dev.) Mono/Stereo [Europe and Australia models] ..................................................75 dB/70 dB Harmonic Distortion (1 kHz) [U.S.A., Canada, Australia, China and General models] Mono/Stereo ...................................0.1/0.2% [Europe model] Mono/Stereo (40 kHz Dev.) ............0.1/0.2% Stereo Separation (1 kHz) [U.S.A., Canada, Australia, China and General models] ...................................50 dB [Europe model (40 kHz Dev.)]..............50 dB Frequency Response 20 Hz to 15 kHz..............................0 ±1.5 dB AM SECTION Tuning Range [U.S.A., Canada, China and General models] .............................................530 to 1,710 kHz [Europe and Australia models] .............................................531 to 1,611 kHz Usable Sensitivity..............................100 µV/m Selectivity ................................................32 dB Signal-to-Noise Ratio ..............................50 dB Image Response Ratio ...........................40 dB Spurious Response Ratio .......................50 dB Harmonic Distortion (1 kHz) .....................0.3% AUDIO SECTION Output Level/Impedance FM (100% mod., 1 kHz) [U.S.A., Canada, Australia, China and General models]............500 mV/2.2 k-ohms [Europe model (40 kHz Dev.)] ......................................400 mV/2.2 k-ohms AM (30% mod., 1 kHz) .........................................150 mV/2.2 k-ohms GENERAL Power Supply [U.S.A. and Canada models] ..............................................AC 120V, 60 Hz [Europe model]......................AC 230V, 50 Hz [Australia model] ...................AC 240V, 50 Hz [China and General models] ....................AC 110/120/220/240V, 50/60 Hz Power Consumption <RX-V493> [U.S.A. model]....................................220W [Except U.S.A. model]........................230W <RX-V393> [U.S.A. model]....................................190W [Canada model]..................................210W [Europe, Australia, China and General models] ..............................................200W Maximum Power Consumption [General model only] (8 ohms, 1 kHz, 10% THD, When 5 channels are driven:) <RX-V493>.........................................540W <RX-V393>.........................................430W AC Outlets 2 SWITCHED OUTLETS [U.S.A., Canada, Europe, China and General models] ................100W max. total 1 SWITCHED OUTLET [Australia model]................100W max. total Dimensions (W x H x D) ......................................435 x 151 x 308.5 mm (17-1/8” x 5-15/16” x 12-1/8”) Weight <RX-V493> .................8.7 kg (19 lbs. 2 oz.) <RX-V393> .................7.8 kg (17 lbs. 3 oz.) Accessories ...........................AM loop antenna Indoor FM antenna Remote control transmitter Batteries Antenna adapter (U.S.A. and Canada models only) Specifications are subject to change without notice. 40 YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA VZ38280 Printed in Malaysia
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43

Yamaha RX-V493RDS El manual del propietario

Categoría
Reproductores de casete
Tipo
El manual del propietario
Este manual también es adecuado para