ASROCK FATAL1TY B250M PERFORMANCE Manual de usuario
- Tipo
- Manual de usuario
Version 1.0
Published October 2016
Copyright©2016 ASRock INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.
Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identication or explanation and to the owners’ benet, without intent to
infringe.
Disclaimer:
Specications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or tness for a particular
purpose.
In no event shall ASRock, its directors, ocers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of prots, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.
is device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/
perchlorate”
ASRock Website: http://www.asrock.com
AUSTRALIA ONLY
Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and compensation for
any other reasonably foreseeable loss or damage caused by our goods. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure. If you require assistance please call ASRock Tel
: +886-2-28965588 ext.123 (Standard International call charges apply)
e terms HDMI™ and HDMI High-Denition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.
Who knew that at age 19, I would be a World Champion PC gamer. When I was 13, I actually
played competitive billiards in professional tournaments and won four or ve games o guys
who played at the highest level. I actually thought of making a career of it, but at that young
age situations change rapidly. Because I’ve been blessed with great hand-eye coordination and
a grasp of mathematics (an important element in video gaming) I gravitated to that activity.
GOING PRO
I started professional gaming in 1999 when I entered the CPL (Cyberathlete Professional
League) tournament in Dallas and won $4,000 for coming in third place. Emerging as one
of the top players in the United States, a company interested in sponsoring me ew me to
Sweden to compete against the top 12 players in the world. I won 18 straight games, lost
none, and took rst place, becoming the number one ranked Quake III player in the world
in the process. Two months later I followed that success by traveling to Dallas and defending
my title as the world’s best Quake III player, winning the $40,000 grand prize. From there
I entered competitions all over the world, including Singapore, Korea, Germany, Australia,
Holland and Brazil in addition to Los Angeles, New York and St. Louis.
WINNING STREAK
I was excited to showcase my true gaming skills when defending my title as CPL
Champion of the year at the CPL Winter 2001 because I would be competing in a totally
dierent rst person shooter (fps) game, Alien vs. Predator II. I won that competition and
walked away with a new car. e next year I won the same title playing Unreal Tournament
2003, becoming the only three-time CPL champion of the year. And I did it playing a
different game each year, something no one else has ever done and a feat of which I am
extremely proud.
At QuakeCon 2002, I faced o against my rival ZeRo4 in one of the most highly
anticipated matches of the year, winning in a 14 to (-1) killer victory. Competing at Quakecon
2004, I became the World’s 1st Doom3 Champion by defeating Daler in a series of very
challenging matches and earning $25,000 for the victory.
Since then Fatal1ty has traveled the globe to compete against the best in the world, winning
prizes and acclaim, including the 2005 CPL World Tour Championship in New York City for
a $150,000 rst place triumph. In August 2007, Johnathan was awarded the rst ever Lifetime
Achievement Award in the four year history of the eSports-Award for “showing exceptional
sportsmanship, taking part in shaping eSports into what it is today and for being the prime
representative of this young sport. He has become the gurehead for eSports worldwide”.
Fatal1ty Story
LIVIN’ LARGE
Since my rst big tournament wins, I have been a “Professional Cyberathlete”, traveling the
world and livin’ large with lots of International media coverage on outlets such as MTV,
ESPN and a 60 Minutes segment on CBS to name only a few. It's unreal - it's crazy. I’m living
a dream by playing video games for a living. I’ve always been athletic and took sports like
hockey and football very seriously, working out and training hard. is discipline helps me
become a better gamer and my drive to be the best has opened the doors necessary to become
a professional.
A DREAM
Now, another dream is being realized – building the ultimate gaming computer, made
up of the best parts under my own brand. Quality hardware makes a huge difference in
competitions…a couple more frames per second and everything gets really nice. It’s all about
getting the computer processing faster and allowing more uid movement around the maps.
My vision for Fatal1ty hardware is to allow gamers to focus on the game without worrying
about their equipment, something I’ve preached since I began competing. I don’t want to
worry about my equipment. I want to be there – over and done with - so I can focus on
the game. I want it to be the fastest and most stable computer equipment on the face of the
planet, so quality is what Fatal1ty Brand products represent.
Johnathan “Fatal1ty” Wendel
e Fatal1ty name, Fatal1ty logos and the Fatal1ty likeness are registered trademarks of Fatal1ty, Inc., and are used
under license. © 2016 Fatal1ty, Inc. All rights reserved. All other trademarks are the property of their respective
owners.
1
English
Fatal1ty B250M Performance Series
Motherboard Layout
Intel
B250
ATXPWR1
HDLE D R ESET
PLED PWR BTN
PANEL 1
1
COM1
1
B250M Performance
RoHS
CPU _FAN 1
PCIE1
TPM S1
1
1
USB3 _4
SPK_ CI1
1
PCIE2
CMOS
Battery
DDR4_A 2 (64 bit, 2 88-pin mod ule)
DDR4_A 1 (64 bit, 2 88-pin mod ule)
DDR4_B 2 (64 bit, 2 88-pin mod ule)
DDR4_B 1 (64 bit, 2 88-pin mod ule)
ATX1 2V 1
SATA3 _ 2
SATA3 _ 3
USB 3_ 5_6
SATA3 _ 4
SATA3 _ 5
CLRM OS1
1
1
HD_A UDI O1
M2_1
CT3CT4 CT2
Top:
RJ-45
HDMI1
CHA _FA N 1
Top:
LIN E IN
Cen te r:
FRO NT
Bot to m:
MIC I N
USB 3 .0
T: U SB3 _TA_ 1
B: US B3_ TC _1
PCIE4
SATA3 _ 1
CHA _FA N 2
Ultra M. 2
PCIe Gen 3 x4
PS2
Keyb oard
PS2
Mous e
DVI1
VGA1
USB 3 .0
T: US B3
B: US B4
CPU _FAN 2
Ct1
1
LPT1
1
USB5 _6
1
BIOS
ROM
M2_2
CT3CT4 CT2 Ct1
SATA3 _ 0
Optane Ready
PCIE3
USB 2 .0
T: U SB1
B: U S B2
FAT AL TY
1
RGB _HE AD ER1
1
2
English
No. Description
1 ATX 12V Power Connector (ATX12V1)
2 Chassis Fan Connector (CHA_FAN1)
3 CPU Fan Connector (CPU_FAN1)
4 CPU Fan Connector (CPU_FAN2)
5 2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_B1)
6 2 x 288-pin DDR4 DIMM Slots (DDR4_A2, DDR4_B2)
7 AURA RGB LED Header (RGB_HEADER1)
8 ATX Power Connector (ATXPWR1)
9 USB 3.0 Header (USB3_5_6)
10 SATA3 Connector (SATA3_0)
11 SATA3 Connector (SATA3_1)
12 Chassis Fan Connector (CHA_FAN2)
13 SATA3 Connector (SATA3_2)
14 SATA3 Connector (SATA3_3)
15 SATA3 Connector (SATA3_5)
16 SATA3 Connector (SATA3_4)
17 Clear CMOS Jumper (CLRMOS1)
18 Chassis Intrusion and Speaker Header (SPK_CI1)
19 System Panel Header (PANEL1)
20 USB 2.0 Header (USB5_6)
21 USB 2.0 Header (USB3_4)
22 TPM Header (TPMS1)
23 Print Port Header (LPT1)
24 COM Port Header (COM1)
25 Front Panel Audio Header (HD_AUDIO1)
3
English
Fatal1ty B250M Performance Series
I/O Panel
No. Description No. Description
1 PS/2 Mouse Port 8 USB 2.0 Port (USB2)
2 D-Sub Port 9 USB 3.0 Ports (USB3_3_4)
3 LAN RJ-45 Port* 10 USB 3.0 Type-A Port (USB3_TA_1)
4 Line In (Light Blue)** 11 USB 3.0 Type-C Port (USB3_TC_1)
5 Front Speaker (Lime)** 12 HDMI Port
6 Microphone (Pink)** 13 DVI-D Port
7 Fatal1ty Mouse Port (USB1) 14 PS/2 Keyboard Port
* ere are two LEDs on the LAN port. Please refer to the table below for the LAN port LED indications.
Activity / Link LED Speed LED
Status Description Status Description
O No Link O 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Link Green 1Gbps connection
ACT/LINK LED
SPEED LED
LAN Port
14 6712
13
5
4
1 3
9
2
11
10
8
4
English
** To congure 7.1 CH HD Audio, it is required to use an HD front panel audio module and enable the multi-
channel audio feature through the audio driver.
Please set Speaker Conguration to “7.1 Speaker”in the Realtek HD Audio Manager.
Function of the Audio Ports in 7.1-channel Conguration:
Port Funct ion
Light Blue (Rear panel) Rear Speaker Out
Lime (Rear panel) Front Speaker Out
Pink (Rear panel) Central /Subwoofer Speaker Out
Lime (Front panel) Side Speaker Out
How to Remove the I/O Cover?
Certain graphics cards with extra thickness of the back plate may collide with the pre-installed I/O cover.
Before installing such a wider graphics card, please loosen the screws to remove the I/O cover, as the picture
shown below.
1
2
5
English
Fatal1ty B250M Performance Series
Chapter 1 Introduction
ank you for purchasing ASRock Fatal1ty B250M Performance Series
motherboard, a reliable motherboard produced under ASRock’s consistently
stringent quality control. It delivers excellent performance with robust design
conforming to ASRock’s commitment to quality and endurance.
1.1 Package Contents
•
ASRock Fatal1ty B250M Performance Series Motherboard (Micro ATX Form Factor)
•
ASRock Fatal1ty B250M Performance Series Quick Installation Guide
•
ASRock Fatal1ty B250M Performance Series Support CD
•
2 x Serial ATA (SATA) Data Cables (Optional)
•
2 x Screws for M.2 Sockets (Optional)
•
1 x I/O Panel Shield
Because the motherboard specications and the BIOS soware might be updated, the
content of this documentation will be subject to change without notice. In case any
modications of this documentation occur, the updated version will be available on
ASRock’s website without further notice. If you require technical support related to
this motherboard, please visit our website for specic information about the model
you are using. You may nd the latest VGA cards and CPU support list on ASRock’s
website as well. ASRock website http://www.asrock.com.
6
English
1.2 Specications
Platform
•
Micro ATX Form Factor
CPU
•
Supports 7
th
and 6
th
Generation Intel® Core
TM
i7/i5/i3/
Pentium®/Celeron® Processors (Socket 1151)
•
Digi Power design
•
6 Power Phase design
•
Supports Intel® Turbo Boost 2.0 Technology
Chipset
•
Intel® B250
Memory
•
Dual Channel DDR4 Memory Technology
•
4 x DDR4 DIMM Slots
•
Supports DDR4 2400/2133 non-ECC, un-buered memory*
* 7
th
Gen Intel® CPU supports DDR4 up to 2400; 6
th
Gen Intel®
CPU supports DDR4 up to 2133.
•
Supports ECC UDIMM memory modules (operate in non-
ECC mode)
•
Max. capacity of system memory: 64GB
•
Supports Intel® Extreme Memory Prole (XMP) 2.0
•
15μ Gold Contact in DIMM Slots
Expansion
Slot
•
2 x PCI Express 3.0 x16 Slots (PCIE1: x16 mode; PCIE4: x4
mode)*
* Supports NVMe SSD as boot disks
•
2 x PCI Express 3.0 x1 Slots (Flexible PCIe)
•
Supports AMD Quad CrossFireX
TM
and CrossFireX
TM
•
15μ Gold Contact in VGA PCIe Slot (PCIE1)
Graphics
•
Intel® HD Graphics Built-in Visuals and the VGA outputs
can be supported only with processors which are GPU
integrated.
•
Supports Intel® HD Graphics Built-in Visuals : Intel® Quick
Sync Video with AVC, MVC (S3D) and MPEG-2 Full
HW Encode1, Intel® InTru
TM
3D, Intel® Clear Video HD
Technology, Intel® Insider
TM
, Intel® HD Graphics
•
Gen9 LP, DX11.3, DX12
7
English
Fatal1ty B250M Performance Series
•
HWAEncode/Decode: VP8, HEVC 8b, VP9, HEVC 10b (For
7
th
Gen Intel® CPU)
•
HWA Encode/Decode: VP8 , HEVC 8b; GPU/SWEncode/
Decode: VP9, HEVC 10b (For 6
th
Gen Intel® CPU)
•
Max. shared memory 1024MB
* e size of maximum shared memory may vary from dierent
operating systems.
•
ree graphics output options: D-Sub, DVI-D and HDMI
•
Supports Triple Monitor
•
Supports HDMI with max. resolution up to 4K x 2K
(4096x2160) @ 24Hz / (3840x2160) @ 30Hz
•
Supports DVI-D with max. resolution up to 1920x1200 @
60Hz
•
Supports D-Sub with max. resolution up to 1920x1200 @
60Hz
•
Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and
HBR (High Bit Rate Audio) with HDMI Port (Compliant
HDMI monitor is required)
•
Supports HDCP with DVI-D and HDMI Ports
•
Supports Full HD 1080p Blu-ray (BD) playback with DVI-D
and HDMI Ports
Audio
•
7.1 CH HD Audio with Content Protection (Realtek ALC892
Audio Codec)
* To congure 7.1 CH HD Audio, it is required to use an HD
front panel audio module and enable the multi-channel audio
feature through the audio driver.
•
Premium Blu-ray Audio support
•
Supports Surge Protection (ASRock Full Spike Protection)
•
Nichicon Fine Gold Series Audio Caps
•
Supports Creative SoundBlaster Cinema3
LAN
•
Gigabit LAN 10/100/1000 Mb/s
•
Giga PHY Intel® I219V
•
Supports Wake-On-LAN
•
Supports Lightning/ESD Protection (ASRock Full Spike
Protection)
•
Supports Energy Ecient Ethernet 802.3az
•
Supports PXE
8
English
Rear Panel
I/O
•
1 x PS/2 Mouse Port
•
1 x PS/2 Keyboard Port
•
1 x D-Sub Port
•
1 x DVI-D Port
•
1 x HDMI Port
•
1 x USB 2.0 Port (Supports ESD Protection (ASRock Full
Spike Protection))
•
1 x Fatal1ty Mouse Port (USB 2.0) (Supports ESD Protection
(ASRock Full Spike Protection))
•
3 x USB 3.0 Type-A Ports (Supports ESD Protection (ASRock
Full Spike Protection))
•
1 x USB 3.0 Type-C Port (Supports ESD Protection (ASRock
Full Spike Protection))
•
1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED
LED)
•
HD Audio Jacks: Line in / Front Speaker / Microphone
Storage
•
6 x SATA3 6.0 Gb/s Connectors, support NCQ, AHCI and
Hot Plug*
* If M2_1 is occupied by a SATA-type M.2 device, SATA3_0 will
be disabled.
•
1 x Ultra M.2 Socket (M2_1), supports type
2230/2242/2260/2280 M.2 SATA3 6.0 Gb/s module and M.2
PCI Express module up to Gen3 x4 (32 Gb/s)**
•
1 x Ultra M.2 Socket (M2_2), supports type
2230/2242/2260/2280 M.2 PCI Express module up to Gen3
x4 (32 Gb/s)**
** If PCIE2 slot or PCIE3 slot is occupied, the PCIe-type M.2
device on M2_1 socket will run at Gen3 x2 (16 Gb/s).
** Supports Intel® Optane
TM
Technology (M2_2 only)
** Supports NVMe SSD as boot disks
** Supports ASRock U.2 Kit
Connector
•
1 x Print Port Header
•
1 x COM Port Header
•
1 x TPM Header
•
1 x Chassis Intrusion and Speaker Header
•
1 x AURA RGB LED Header
•
2 x CPU Fan Connectors (1 x 4-pin, 1 x 3-pin)
* e CPU Fan Connector supports the CPU fan of maximum
1A (12W) fan power.
9
English
Fatal1ty B250M Performance Series
•
2 x Chassis Fan Connectors (4-pin) (Smart Fan Speed Con-
trol)
* CHA_FAN1 and CHA_FAN2 can auto detect if 3-pin or 4-pin
fan is in use.
•
1 x 24 pin ATX Power Connector
•
1 x 8 pin 12V Power Connector
•
1 x Front Panel Audio Connector
•
2 x USB 2.0 Headers (Support 4 USB 2.0 ports) (Supports
ESD Protection (ASRock Full Spike Protection))
•
1 x USB 3.0 Header (Supports 2 USB 3.0 ports) (Supports
ESD Protection (ASRock Full Spike Protection))
BIOS
Feature
•
AMI UEFI Legal BIOS with multilingual GUI support
•
ACPI 6.0 Compliant wake up events
•
SMBIOS 2.7 Support
•
CPU, GT_CPU, DRAM, PCH 1.0V, VCCIO, VCCSA, VCCST
Voltage Multi-adjustment
Hardware
Monitor
•
CPU/Chassis temperature sensing
•
CPU/Chassis Fan Tachometer
•
CPU/Chassis Quiet Fan (Auto adjust chassis fan speed by
CPU temperature)
•
CPU/Chassis Fan multi-speed control
•
CASE OPEN detection
•
Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore, DRAM,
PCH 1.0V
OS
•
Microso® Windows® 10 64-bit (For 7
th
Gen Intel® CPU)
•
Microso® Windows® 10 64-bit / 8.1 64-bit / 7 32-bit / 7 64-
bit (For 6
th
Gen Intel® CPU)
* To install Windows® 7 OS, a modied installation disk with
xHCI drivers packed into the ISO le is required. Please refer to
page 153 for more detailed instructions.
* For the updated Windows® 10 driver, please visit ASRock’s
website for details: http://www.asrock.com
Certica-
tions
•
FCC, CE, WHQL, RCM, BSMI
•
ErP/EuP Ready (ErP/EuP ready power supply is required)
* For detailed product information, please visit our website:
http://www.asrock.com
10
English
Please realize that there is a certain risk involved with overclocking, including
adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using
third-party overclocking tools. Overclocking may aect your system’s stability, or
even cause damage to the components and devices of your system. It should be done
at your own risk and expense. We are not responsible for possible damage caused by
overclocking.
11
English
Fatal1ty B250M Performance Series
is is a Micro ATX form factor motherboard. Before you install the motherboard,
study the conguration of your chassis to ensure that the motherboard ts into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard components
or change any motherboard settings.
•
Make sure to unplug the power cord before installing or removing the motherboard
components. Failure to do so may cause physical injuries and damages to motherboard
components.
•
In order to avoid damage from static electricity to the motherboard’s components,
NEVER place your motherboard directly on a carpet. Also remember to use a grounded
wrist strap or touch a safety grounded object before you handle the components.
•
Hold components by the edges and do not touch the ICs.
•
Whenever you uninstall any components, place them on a grounded anti-static pad or
in the bag that comes with the components.
•
When placing screws to secure the motherboard to the chassis, please do not over-
tighten the screws! Doing so may damage the motherboard.
Chapter 2 Installation
12
English
2.1 Installing the CPU
1. Before you insert the 1151-Pin CPU into the socket, please check if the PnP cap
is on the socket, if the CPU surface is unclean, or if there are any bent pins in the
socket. Do not force to insert the CPU into the socket if above situation is found.
Otherwise, the CPU will be seriously damaged.
2. Unplug all power cables before installing the CPU.
1
2
A
B
13
English
Fatal1ty B250M Performance Series
4
5
3
14
English
Please save and replace the cover if the processor is removed. e cover must be
placed if you wish to return the motherboard for aer service.
15
English
Fatal1ty B250M Performance Series
2.2 Installing the CPU Fan and Heatsink
1 2
CPU_
FAN
16
English
2.3 Installing Memory Modules (DIMM)
is motherboard provides four 288-pin DDR4 (Double Data Rate 4) DIMM slots,
and supports Dual Channel Memory Technology.
Dual Channel Memory Conguration
e DIMM only ts in one correct orientation. It will cause permanent damage to
the motherboard and the DIMM if you force the DIMM into the slot at incorrect
orientation.
Priority DDR4_A1 DDR4_A2 DDR4_B1 DDR4_B2
1 Populated Populated
2 Populated Populated
3 Populated Populated Populated Populated
1. For dual channel conguration, you always need to install identical (the same
brand, speed, size and chip-type) DDR4 DIMM pairs.
2. It is unable to activate Dual Channel Memory Technology with only one or three
memory module installed.
3. It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4
slot; otherwise, this motherboard and DIMM may be damaged.
17
English
Fatal1ty B250M Performance Series
1
2
3
18
English
1. For a better thermal environment, please connect a chassis fan to the mother-
board’s chassis fan connector (CHA_FAN1 or CHA_FAN2) when using multiple
graphics cards.
2. If PCIE2 slot or PCIE3 slot is occupied, the PCIe-type M.2 device on M2_1 socket
will run at Gen3 x2 (16 Gb/s).
2.4 Expansion Slots (PCI Express Slots)
ere are 4 PCI Express slots on the motherboard.
PCIe slots:
PCIE1 (PCIe 3.0 x16 slot) is used for PCI Express x16 lane width graphics cards.
PCIE2 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.
PCIE3 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.
PCIE4 (PCIe 3.0 x16 slot) is used for PCI Express x4 lane width graphics cards.
PCIe Slot Congurations
Before installing an expansion card, please make sure that the power supply is
switched o or the power cord is unplugged. Please read the documentation of the
expansion card and make necessary hardware settings for the card before you start
the installation.
PCIE1 PCIE4
Single Graphics Card x16 N/A
Two Graphics Cards in
CrossFireX
TM
Mode
x16 x4
19
English
Fatal1ty B250M Performance Series
2.5 Onboard Headers and Connectors
System Panel Header
(9-pin PANEL1)
(see p.1, No. 19)
Connect the power
switch, reset switch and
system status indicator on
the chassis to this header
according to the pin
assignments below. Note
the positive and negative
pins before connecting
the cables.
PWRBTN (Power Switch):
Connect to the power switch on the chassis front panel. You may congure the way to
turn o your system using the power switch.
RESET (Reset Switch):
Connect to the reset switch on the chassis front panel. Press the reset switch to restart
the computer if the computer freezes and fails to perform a normal restart.
PLED (System Power LED):
Connect to the power status indicator on the chassis front panel. e LED is on when
the system is operating. e LED keeps blinking when the system is in S1/S3 sleep
state. e LED is o when the system is in S4 sleep state or powered o (S5).
HDLED (Hard Drive Activity LED):
Connect to the hard drive activity LED on the chassis front panel. e LED is on
when the hard drive is reading or writing data.
e front panel design may dier by chassis. A front panel module mainly consists
of power switch, reset switch, power LED, hard drive activity LED, speaker and etc.
When connecting your chassis front panel module to this header, make sure the wire
assignments and the pin assignments are matched correctly.
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over
these headers and connectors. Placing jumper caps over the headers and connectors
will cause permanent damage to the motherboard.
GND
R ESET#
P WRBTN#
P LED-
P LED+
GND
H DLED-
H DLED+
1
GND
20
English
Chassis Intrusion and
Speaker Header
(7-pin SPK_CI1)
(see p.1, No. 18)
Please connect the
chassis intrusion and the
chassis speaker to this
header.
Serial ATA3 Connectors
(SATA3_0:
see p.1, No. 10)
(SATA3_1:
see p.1, No. 11)
(SATA3_2:
see p.1, No. 13)
(SATA3_3:
see p.1, No. 14)
(SATA3_4:
see p.1, No. 16)
(SATA3_5:
see p.1, No. 15)
ese six SATA3
connectors support SATA
data cables for internal
storage devices with up to
6.0 Gb/s data transfer rate.
If M2_1 is occupied by a
SATA-type M.2 device,
SATA3_0 will be disabled.
USB 2.0 Headers
(9-pin USB3_4)
(see p.1, No. 21)
(9-pin USB5_6)
(see p.1, No. 20)
ere are two headers
on this motherboard.
Each USB 2.0 header can
support two ports.
USB 3.0 Header
(19-pin USB3_5_6)
(see p.1, No. 9)
ere is one header on
this motherboard. is
USB 3.0 header can
support two ports.
1
IntA_ PB_D +
Dummy
IntA_ PB_D -
GND
IntA_ PB_S ST X +
GND
IntA_ PB_S ST X -
IntA_ PB_S SR X +
IntA_ PB_S SR X -
VbusVbus
Vbus
IntA_ PA_S SR X -
IntA_ PA_S SR X +
GND
IntA_ PA_S ST X -
IntA_ PA_S ST X +
GND
IntA_ PA_D -
IntA_ PA_D +
1
+5V
DUMMY
SIGNAL
GND
DUMMY
SPEAKER
DUMMY
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
USB_PWR
1
SATA3_4
SATA3_5
SATA3_2
SATA3_3
SATA3_1
SATA3_0
21
English
Fatal1ty B250M Performance Series
Front Panel Audio Header
(9-pin HD_AUDIO1)
(see p.1, No. 25)
is header is for
connecting audio devices
to the front audio panel.
Chassis Fan Connectors
(4-pin CHA_FAN1)
(see p.1, No. 2)
(4-pin CHA_FAN2)
(see p.1, No. 12)
Please connect fan cables
to the fan connector and
match the black wire to
the ground pin.
CPU Fan Connectors
(4-pin CPU_FAN1)
(see p.1, No. 3)
(3-pin CPU_FAN2)
(see p.1, No. 4)
is motherboard pro-
vides a 4-Pin CPU fan
(Quiet Fan) connector.
If you plan to connect a
3-Pin CPU fan, please
connect it to Pin 1-3.
1. High Denition Audio supports Jack Sensing, but the panel wire on the chassis
must support HDA to function correctly. Please follow the instructions in our
manual and chassis manual to install your system.
2. If you use an AC’97 audio panel, please install it to the front panel audio header by
the steps below:
A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for the HD audio panel only. You don’t need to
connect them for the AC’97 audio panel.
E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel
and adjust “Recording Volume”.
GND
FAN_VOLTAGE_ CONTROL
FAN_SPEE D
FAN_SPEE D_CONTROL
J _SENSE
O UT2_L
1
M IC_RET
P RESENCE#
GN D
O UT2_R
M IC2_R
M IC2_L
OUT_RET
GND
FAN_VOLTAGE_CO NTROL
FAN_SPEED
FAN_SPEED _CONTROL
FAN_VOLTAGE
GND
FAN_SPEED
FAN_SPEED_CONTROL
1
2
3
4
GND
FA N_VOLTAGE
FA N_SPEED
22
English
ATX Power Connector
(24-pin ATXPWR1)
(see p.1, No. 8)
is motherboard pro-
vides a 24-pin ATX power
connector. To use a 20-pin
ATX power supply, please
plug it along Pin 1 and Pin
13.
ATX 12V Power
Connector
(8-pin ATX12V1)
(see p.1, No. 1)
is motherboard pro-
vides an 8-pin ATX 12V
power connector. To use a
4-pin ATX power supply,
please plug it along Pin 1
and Pin 5.
Serial Port Header
(9-pin COM1)
(see p.1, No. 24)
is COM1 header
supports a serial port
module.
TPM Header
(17-pin TPMS1)
(see p.1, No. 22)
is connector supports Trusted
Platform Module (TPM) system,
which can securely store keys,
digital certicates, passwords,
and data. A TPM system also
helps enhance network security,
protects digital identities, and
ensures platform integrity.
Print Port Header
(25-pin LPT1)
(see p.1, No. 23)
is is an interface
for print port cable
that allows convenient
connection of printer
devices.
1
GN D
SM B _DATA_MAIN
LA D 2
LA D 1
GN D
S_ P WRDWN #
SE R IRQ #
GN
D
P C I C L K
P C I R ST #
LA D 3
+3 V
LA D 0
+3VS B
GN D
FR A M E
SM B _CLK_MAIN
12
1
24
13
5
1
8
4
1
AF D #
ER R OR#
PI N IT#
GN D
SL I N#
ST B #
SP D 0
SP D 1
SP D 2
SP D 3
SP D 4
SP D 5
SP D 6
SP D 7
AC K #
BU S Y
PE
SL C T
23
English
Fatal1ty B250M Performance Series
AURA RGB LED Header
(4-pin RGB_HEADER1)
(see p.1, No. 7)
AURA RGB LED header is used
to connect RGB LED exten-
sion cable which allows users to
choose from various LED light-
ing eects.
24
English
2.6 M.2_SSD (NGFF) Module Installation Guide
The M.2, also known as the Next Generation Form Factor (NGFF), is a small size and
versatile card edge connector that aims to replace mPCIe and mSATA. The Ultra M.2
Socket (M2_1) supports type 2230/2242/2260/2280 M.2 SATA3 6.0 Gb/s module and M.2
PCI Express module up to Gen3 x4 (32 Gb/s). e Ultra M.2 Socket (M2_2) supports type
2230/2242/2260/2280 M.2 PCI Express module up to Gen3 x4 (32 Gb/s).
* Please be noted that if M2_1 is occupied by a SATA-type M.2 device, SATA3_0 will be
disabled.
* If PCIE2 slot or PCIE3 slot is occupied, the PCIe-type M.2 device on M2_1 socket will
run at Gen3 x2 (16 Gb/s).
Installing the M.2_SSD (NGFF) Module
Step 1
Prepare a M.2_SSD (NGFF) module
and the screw.
BCD
E
A
Step 2
Depending on the PCB type and
length of your M.2_SSD (NGFF)
module, nd the corresponding nut
location to be used.
No. 1 2 3 4
Nut Location A B C D
PCB Length 3cm 4.2cm 6cm 8cm
Module Type Type2230 Type 2242 Type2260 Type 2280
25
English
Fatal1ty B250M Performance Series
3
2
4
5
BCDE
A
1
Step 3
Move the stando based on the
module type and length.
e stando is placed at the nut
location D by default. Skip Step 3 and
4 and go straight to Step 5 if you are
going to use the default nut.
Otherwise, release the stando by
hand.
BCD
E
A
Step 4
Peel o the yellow protective lm on
the nut to be used. Hand tighten the
stando into the desired nut location
on the motherboard.
ABCDE
BC
A
Step 5
Align and gently insert the M.2
(NGFF) SSD module into the M.2
slot. Please be aware that the M.2
(NGFF) SSD module only ts in one
orientation.
NUT1NUT2D
E
Step 6
Tighten the screw with a screwdriver
to secure the module into place.
Please do not overtighten the screw as
this might damage the module.
26
English
M.2_SSD (NGFF) Module Support List
For the latest updates of M.2_SSD (NFGG) module support list, please visit our website
for details: http://www.asrock.com
Vendor Size Interface Length P/N
ADATA 128GB SATA3 2280 AXNS381E-128GM-B
ADATA 256GB SATA3 2280 AXNS381E-256GM-B
ADATA 32GB SATA3 2230 AXNS330E-32GM-B
Crucial 120GB SATA3 2280 CT120M500SSD4
Crucial 240GB SATA3 2280 CT240M500SSD4
Intel 80GB SATA3 2280 Intel SSDSCKGW080A401/80G
Intel 256GB PCIe3 x4 2280 SSDPEKKF256G7
Intel 512GB PCIe3 x4 2280 SSDPEKKF512G7
Kingston 120GB SATA3 2280 SM2280S3
Kingston 480GB PCIe2 x4 2280 SH2280S3/480G
OCZ 512GB PCIe3 x4 2280 RVD400 -M2280-512G (NVME)
Plextor 128GB PCIe3 x4 2280 PX-128M8PeG
Plextor 1TB PCIe3 x4 2280 PX-1TM8PeG
Plextor 256GB PCIe3 x4 2280 PX-256M8PeG
Plextor 256GB PCIe 2280 PX-G256M6e
Plextor 512GB PCIe3 x4 2280 PX-512M8PeG
Plextor 512GB PCIe 2280 PX-G512M6e
Samsung 256GB PCIe3 x4 2280 SM951 (MZHPV256HDGL)
Samsung 256GB PCIe3 x4 2280 SM951 (NVME)
Samsung 512GB PCIe3 x4 2280 SM951 (MZHPV512HDGL)
Samsung 512GB PCIe3 x4 2280 SM951 (NVME)
Samsung 512GB PCIe x4 2280 XP941-512G (MZHPU512HCGL)
SanDisk 128GB PCIe 2260 SD6PP4M-128G
SanDisk 256GB PCIe 2260 SD6PP4M-256G
Team 128GB SATA3 2242 TM4PS4128GMC105
Team 128GB SATA3 2280 TM8PS4128GMC105
Team 256GB SATA3 2280 TM8PS4256GMC105
Team 256GB SATA3 2242 TM4PS4256GMC105
Transcend 256GB SATA3 2242 TS256GMTS400
Transcend 512GB SATA3 2260 TS512GMTS600
Transcend 512GB SATA3 2280 TS512GMTS800
V-Color 120GB SATA3 2280 VLM100-120G-2280B-RD
V-Color 240GB SATA3 2280 VLM100-240G-2280B-RD
V-Color 240GB SATA3 2280 VSM100-240G-2280
27
Deutsch
Fatal1ty B250M Performance Series
1 Einleitung
Vielen Dank, dass Sie sich für das Fatal1ty B250M Performance Series von ASRock
entschieden haben – ein zuverlässiges Motherboard, das konsequent unter der
strengen Qualitätskontrolle von ASRock hergestellt wurde. Es liefert ausgezeichnete
Leistung mit robustem Design, das ASRock Streben nach Qualität und Beständigkeit
erfüllt.
1.1 Lieferumfang
•
ASRock Fatal1ty B250M Performance Series-Motherboard (Micro-ATX-Formfaktor)
•
ASRock Fatal1ty B250M Performance Series-Schnellinstallationsanleitung
•
ASRock Fatal1ty B250M Performance Series-Support-CD
•
2 x Serial-ATA- (SATA) Datenkabel (optional)
•
2 x Schrauben für M.2-Sockel (optional)
•
1 x E/A-Blendenabschirmung
Da die technischen Daten des Motherboards sowie die BIOS-Soware aktualisiert
werden können, kann der Inhalt dieser Dokumentation ohne Ankündigung geändert
werden. Falls diese Dokumentation irgendwelchen Änderungen unterliegt, wird die aktu-
alisierte Version ohne weitere Hinweise auf der ASRock-Webseite zur Verfügung gestellt.
Sollten Sie technische Hilfe in Bezug auf dieses Motherboard benötigen, erhalten Sie auf
unserer Webseite spezischen Informationen über das von Ihnen verwendete Modell.
Auch nden Sie eine aktuelle Liste unterstützter VGA-Karten und Prozessoren auf der
ASRock-Webseite: ASRock-Website http://www.asrock.com.
28
Deutsch
1.2 Technische Daten
Plattform
•
Micro-ATX-Formfaktor
Prozessor
•
Unterstützt Intel®-Core
TM
-i7/i5/i3/Pentium®/Celeron®-Prozessoren
der 7. und 6. Generation (Sockeö 1151)
•
Digi Power design
•
6-Leistungsphasendesign
•
Unterstützt Intel® Turbo Boost 2.0-Technologie
Chipsatz
•
Intel® B250
Speicher
•
Dualkanal-DDR4-Speichertechnologie
•
4 x DDR4-DIMM-Steckplätze
•
Unterstützt ungepuerten DDR4-2400/2133-Non-ECC-Speicher*
* Intel®-Prozessor der 7. Generation unterstützt DDR4 bis 2400;
Intel®-Prozessor der 6. Generation unterstützt DDR4 bis 2133.
•
Unterstützt ECC-UDIMM-Speichermodule (Betrieb im non-
ECC-Modus)
•
Systemspeicher, max. Kapazität: 64GB
•
Unterstützt Intel® Extreme Memory Prole (XMP) 2.0
•
15-μ-Goldkontakt in DIMM-Steckplätze
Erweiter-
ungs-
steckplatz
•
2 x PCI-Express 3.0-x16-Steckplatz (PCIE1:x16-Modus;
PCIE4:x4-Modus)*
* Unterstützt NVMe-SSD als Bootplatte
•
2 x PCI-Express 3.0-x1-Steckplatz (Flexible PCIe)
•
Unterstützt AMD Quad CrossFireX
TM
und CrossFireX
TM
•
15-μ-Goldkontakt in VGA-PCIe-Steckplatz (PCIE1)
Grakkarte
•
Integrierte Intel® HD Graphics-Visualisierung und VGA-
Ausgänge können nur mit Prozessoren unterstützt werden, die
GPU-integriert sind.
•
Unterstützt integrierte Intel® HD Graphics-Visualisierung: Intel®
Quick Sync Video mit AVC, MVC (S3D) und MPEG-2 Full HW
Encode1, Intel® InTru
TM
3D, Intel® Clear Video HD Technology,
Intel® Insider
TM
, Intel® HD Graphics
•
Gen9 LP, DX11.3, DX12
•
HWA encodieren/decodieren: VP8, HEVC 8b, VP9, HEVC 10b
(bei Intel®-Prozessor der 7. Generation)
29
Deutsch
Fatal1ty B250M Performance Series
•
HWA encodieren/decodieren: VP8, HEVC 8b; GPU/SW
encodieren/decodieren: VP9, HEVC 10b (bei Intel®-Prozessor der
6. Generation)
•
Max. geteilter Speicher: 1024 MB
* Die Größe des maximalen Freigabespeichers kann je nach
Betriebssystem variieren.
•
Drei Grakkarten-Ausgangsoptionen: D-Sub, DVI-D und HDMI
•
Unterstützt drei Monitore
•
Unterstützt HDMI mit maximaler Auösung von 4K x 2K (4096 x
2160) bei 24 Hz / (3840 x 2160) bei 30 Hz
•
Unterstützt DVI-D mit maximaler Auösung von 1920 x 1200 bei
60 Hz
•
Unterstützt D-Sub mit maximaler Auösung von 1920 x 1200 bei
60 Hz
•
Unterstützt Auto-Lippensynchronizität, hohe Farbtiefe (12 bpc),
xvYCC und HBR (Audio mit hoher Bitrate) mit HDMI-Port
(konformer HDMI-Monitor erforderlich)
•
Unterstützt HDCP mit DVI-D- und HDMI-Ports
•
Unterstützt Blu-ray- (BD) Wiedergabe (Full HD/1080p) mit
DVI-D- und HDMI-Ports
Audio
•
7.1-Kanal-HD-Audio mit Inhaltsschutz (Realtek ALC892-Audi-
ocodec)
* Zur Konguration von 7.1-Kanal-HD-Audio müssen Sie ein HD-
Frontblenden-Audiomodul nutzen und den Mehrkanalton über den
Audiotreiber aktivieren.
•
Erstklassige Blu-ray-Audiounterstützung
•
Unterstützt Überspannungsschutz (ASRock Full Spike Protection)
•
Nichicon-Audiokappen der Fine Gold-Serie
•
Unterstützt Creative SoundBlaster Cinema3
LAN
•
Gigabit LAN 10/100/1000 Mb/s
•
Giga PHY Intel® I219V
•
Unterstützt Wake-On-LAN
•
Unterstützt Blitzschutz/Schutz gegen elektrostatische Entladung
(ASRock Full Spike Protection)
•
Unterstützt energieezientes Ethernet 802.3az
•
Unterstützt PXE
30
Deutsch
Rückblende,
E/A
•
1 x PS/2-Mausanschluss
•
1 x PS/2-Tastaturanschluss
•
1 x D-Sub-Port
•
1 x DVI-D-Port
•
1 x HDMI-Port
•
1 x USB 2.0-Port (unterstützt Schutz gegen elektrostatische
Entladung (ASRock Full Spike Protection))
•
1 x Fatal1ty-Mausport (USB 2.0) (unterstützt Schutz gegen
elektrostatische Entladung (ASRock Full Spike Protection))
•
3 x USB 3.0-Typ-A-Ports (unterstützt Schutz gegen
elektrostatische Entladung (ASRock Full Spike Protection))
•
1 x USB 3.0-Typ-C-Port (unterstützt Schutz gegen elektrostatische
Entladung (ASRock Full Spike Protection))
•
1 x RJ-45-LAN-Port mit LED (Aktivität/Verbindung-LED und
Geschwindigkeit-LED)
•
HD-Audioanschlüsse: Line-in / Vorderer Lautsprecher / Mikrofon
Speicher
•
6 x SATA-III-6,0-Gb/s-Abschluss, unterstützt NCQ, AHCI und
Hot-Plugging*
* Wenn M2_1 durch ein SATA-Typ-M.2-Gerät belegt ist, wird
SATA3_0 deaktiviert.
•
1 x Ultra-M.2-Sockel (M2_1), unterstützt
2230-/2242-/2260-/2280-M.2-SATA-III-6,0-Gb/s-Modul und
M.2-PCI-Express-Modul bis Gen3 x 4 (32 Gb/s)**
•
1 x Ultra-M.2-Sockel (M2_2), unterstützt
2230-/2242-/2260-/2280-M.2-PCI-Express-Modul bis Gen3 x 4
(32 Gb/s)**
** Falls der PCIE2- oder PCIE3-Steckplatz belegt ist, läu das PCIe-
M.2-Gerät am M2_1-Steckplatz bei Gen. 3 x 2 (16 Gb/s).
** Unterstützt Intel® Optane
TM
-Technologie (M2_2)
** Unterstützt NVMe-SSD als Bootplatte
** Unterstützt ASRock U.2-Kit
31
Deutsch
Fatal1ty B250M Performance Series
Anschluss
•
1 Druckerport-Anschlussleiste
•
1 x COM-Anschluss-Stileiste
•
1 x TPM-Stileiste
•
1 x Gehäuseeingri- und Lautsprecher-Stileiste
•
2 x CPU-Lüeranschlüsse (1 x 4-polig, 1 x 3-polig)
* Der CPU-Lüeranschluss unterstützt einen CPU-Lüer mit einer
maximalen Lüerleistung von 1 A (12 W).
•
2 x Gehäuselüeranschlüsse (4-polig) (intelligente Lüerge-
schwindigkeitssteuerung)
* CHA_FAN1 und CHA_FAN2 können automatisch erkennen, ob
ein 3- oder 4-poliger Lüer verwendet wird.
•
1 x 24-poliger ATX-Netzanschluss
•
1 x 8-poliger 12-V-Netzanschluss
•
1 x Audioanschluss an Frontblende
•
2 x USB-2.0-Stileiste (unterstützen 4 USB-2.0-Ports) (unterstützt
Schutz gegen elektrostatische Entladung (ASRock Full Spike
Protection))
•
1 x USB-3.0-Stileiste (unterstützt 2 USB-3.0-Ports) (unterstützt
Schutz gegen elektrostatische Entladung (ASRock Full Spike
Protection))
BIOS-Funk-
tion
•
AMI-UEFI-Legal-BIOS mit Unterstützung mehrsprachiger
grascher Benutzerschnittstellen
•
ACPI 6.0-konforme Aufweckereignisse
•
SMBIOS 2.7-Unterstützung
•
CPU, GT_CPU, DRAM, PCH 1.0V, VCCIO, VCCSA, VCCST
Mehrfachspannungsanpassung
Hard-
wareüber-
wachung
•
CPU-/Gehäusetemperaturerkennung
•
CPU-/Gehäuselüertachometer
•
Lautloser CPU-/Gehäuselüer (automatische Anpassung der
Gehäuselüergeschwindigkeit durch CPU-Temperatur)
•
CPU-/Gehäuselüer-Mehrfachgeschwindigkeitssteuerung
•
Gehäuse-oen-Erkennung
•
Spannungsüberwachung: +12 V, +5 V, +3,3 V, CPU Vcore,
DRAM, PCH 1,0V
32
Deutsch
* Detaillierte Produktinformationen nden Sie auf unserer Webseite: http://www.asrock.com
Bitte beachten Sie, dass mit einer Übertaktung, zu der die Anpassung von BIOS-
Einstellungen, die Anwendung der Untied Overclocking Technology oder die Nutzung
von Übertaktungswerkzeugen von Drittanbietern zählen, bestimmte Risiken verbunden
sind. Eine Übertaktung kann sich auf die Stabilität Ihres Systems auswirken und sogar
Komponenten und Geräte Ihres Systems beschädigen. Sie sollte auf eigene Gefahr und
eigene Kosten durchgeführt werden. Wir übernehmen keine Verantwortung für mögliche
Schäden, die durch eine Übertaktung verursacht wurden.
Betriebssys-
tem
•
Microso® Windows® 10, 64 Bit (nur bei Intel®-Prozessor der 7.
Generation)
•
Microso® Windows® 10, 64 Bit / 8.1, 64 Bit / 7, 32 Bit / 7, 64 Bit
(nur bei Intel®-Prozessor der 6. Generation)
* Zur Installation des Windows® 7-Betriebssystems wird ein modi-
ziertes Installationslaufwerk mit xHCI-Treibern in der ISO-Datei
benötigt. Detaillierte Anweisungen nden Sie auf Seite 153.
* Einzelheiten zum aktualisierten Windows® 10-Treiber entnehmen
Sie bitte der ASRock-Webseite:http://www.asrock.com
Zerti-
zierungen
•
FCC, CE, WHQL, RCM, BSMI
•
ErP/EuP ready (ErP/EuP ready-Netzteil erforderlich)
33
Deutsch
Fatal1ty B250M Performance Series
1.3 Integrierte Stiftleisten und Anschlüsse
Systemblende-Stileiste
(9-polig, PANEL1)
(siehe S. 1, Nr. 19)
Verbinden Sie Netzschalter,
Reset-Taste und
Systemstatusanzeige am
Gehäuse entsprechend
der nachstehenden
Pinbelegung mit dieser
Stileiste. Beachten Sie vor
Anschließen der Kabel die
positiven und negativen
Kontakte.
PWRBTN (Ein-/Austaste):
Mit der Ein-/Austaste an der Frontblende des Gehäuses verbinden. Sie können die
Abschaltung Ihres Systems über die Ein-/Austaste kongurieren.
RESET (Reset-Taste):
Mit der Reset-Taste an der Frontblende des Gehäuses verbinden. Starten Sie den Compu-
ter über die Reset-Taste neu, wenn er abstürzt oder sich nicht normal neu starten lässt.
PLED (Systembetriebs-LED):
Mit der Betriebsstatusanzeige an der Frontblende des Gehäuses verbinden. Die LED
leuchtet, wenn das System läu. Die LED blinkt, wenn sich das System im S1/S3-Ruhe-
zustand bendet. Die LED ist aus, wenn sich das System im S4-Ruhezustand bendet
oder ausgeschaltet ist (S5).
HDLED (Festplattenaktivitäts-LED):
Mit der Festplattenaktivitäts-LED an der Frontblende des Gehäuses verbinden. Die LED
leuchtet, wenn die Festplatte Daten liest oder schreibt.
Das Design der Frontblende kann je nach Gehäuse variieren. Ein Frontblendenmodul
besteht hauptsächlich aus Ein-/Austaste, Reset-Taste, Betrieb-LED, Festplattenaktivität-
LED, Lautsprecher etc. Stellen Sie beim Anschließen Ihres Frontblendenmoduls an diese
Stileiste sicher, dass Kabel- und Pinbelegung richtig abgestimmt sind.
Integrierte Stileisten und Anschlüsse sind KEINE Jumper. Bringen Sie KEINE Jumper-
Kappen an diesen Stileisten und Anschlüssen an. Durch Anbringen von Jumper-
Kappen an diesen Stileisten und Anschlüssen können Sie das Motherboard dauerha
beschädigen.
GND
R ESET#
P WRBTN#
P LED-
P LED+
GND
H DLED-
H DLED+
1
GND
34
Deutsch
Gehäuseeingris- und
Lautsprecher-Stileiste
(7-polig, SPK_CI1)
(siehe S. 1, Nr. 18)
Bitte verbinden Sie Gehäu-
seeingrisvorrichtung und
den Gehäuselautsprecher
mit dieser Stileiste.
Serial-ATA-III-Anschlüsse
(SATA3_0:
siehe S. 1, Nr. 10)
(SATA3_1:
siehe S. 1, Nr. 11)
(SATA3_2:
siehe S. 1, Nr. 13)
(SATA3_3:
siehe S. 1, Nr. 14)
(SATA3_4:
siehe S. 1, Nr. 16)
(SATA3_5:
siehe S. 1, Nr. 15)
Diese sechs SATA-III-
Anschlüsse unterstützen
SATA-Datenkabel für
interne Speichergeräte mit
einer Datenübertragungsge
schwindigkeit bis 6,0 Gb/s.
Wenn M2_1 durch ein
SATA-Typ-M.2-Gerät
belegt ist, wird SATA3_0
deaktiviert.
USB 2.0-Stileisten
(9-polig, USB3_4)
(siehe S. 1, Nr. 21)
(9-polig, USB5_6)
(siehe S. 1, Nr. 20)
Es gibt zwei Stileisten an
diesem Motherboard. Jede
USB 2.0-Stileiste kann
zwei Ports unterstützen.
USB 3.0-Stileiste
(19-polig, USB3_5_6)
(siehe S. 1, Nr. 9)
Es gibt eine Stileiste an
diesem Motherboard. Jede
USB 3.0-Stileiste kann
zwei Ports unterstützen.
1
IntA_ PB_D +
Dummy
IntA_ PB_D -
GND
IntA_ PB_S ST X +
GND
IntA_ PB_S ST X -
IntA_ PB_S SR X +
IntA_ PB_S SR X -
VbusVbus
Vbus
IntA_ PA_S SR X -
IntA_ PA_S SR X +
GND
IntA_ PA_S ST X -
IntA_ PA_S ST X +
GND
IntA_ PA_D -
IntA_ PA_D +
1
+5V
DUMMY
SIGNAL
GND
DUMMY
SPEAKER
DUMMY
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
USB_PWR
1
SATA3_4
SATA3_5
SATA3_2
SATA3_3
SATA3_1
SATA3_0
35
Deutsch
Fatal1ty B250M Performance Series
Audiostileiste
(Frontblende)
(9-polig, HD_AUDIO1)
(siehe S. 1, Nr. 25)
Diese Stileiste dient
dem Anschließen von
Audiogeräten an der
Frontblende.
Gehäuselüeranschlüsse
(4-polig, CHA_FAN1)
(siehe S. 1, Nr. 2)
(4-polig, CHA_FAN2)
(siehe S. 1, Nr. 12)
Bitte verbinden Sie das
Lüerkabel mit dem
Lüeranschluss; der
schwarze Draht gehört zum
Erdungskontakt.
CPU-Lüeranschlüsse
(4-polig, CPU_FAN1)
(siehe S. 1, Nr. 3)
(3-polig, CPU_FAN2)
(siehe S. 1, Nr. 4)
Dieses Motherboard
bietet einen 4-poligen
CPU-Lüeranschluss
(lautloser Lüer). Falls Sie
einen 3-poligen CPU-Lüer
anschließen möchten,
verbinden Sie ihn bitte mit
Kontakt 1 bis 3.
1. High Denition Audio unterstützt Anschlusserkennung, der Draht am Gehäuse muss
dazu jedoch HDA unterstützt. Bitte befolgen Sie zum Installieren Ihres Systems die
Anweisungen in unserer Anleitung und der Anleitung zum Gehäuse.
2. Bei Nutzung eines AC’97-Audiopanels dieses bitte anhand folgender Schritte an der
Audiostileiste der Frontblende installieren:
A. Mic_IN (Mikrofon) mit MIC2_L verbinden.
B. Audio_R (RIN) mit OUT2_R und Audio_L (LIN) mit OUT2_L verbinden.
C. Erde (GND) mit Erde (GND) verbinden.
D. MIC_RET und OUT_RET sind nur für das HD-Audiopanel vorgesehen. Sie müssen
sie nicht für das AC’97-Audiopanel verbinden.
E. Rufen Sie zum Aktivieren des vorderen Mikrofons das „FrontMic (Vorderes
Mikrofon)“-Register in der Realtek-Systemsteuerung auf und passen „Recording
Volume (Aufnahmelautstärke)“ an.
GND
FAN_VOLTAGE_ CONTROL
FAN_SPEE D
FAN_SPEE D_CONTROL
J _SENSE
O UT2_L
1
M IC_RET
P RESENCE#
GN D
O UT2_R
M IC2_R
M IC2_L
OUT_RET
GND
FAN_VOLTAGE_CO NTROL
FAN_SPEED
FAN_SPEED _CONTROL
FAN_VOLTAGE
GND
FAN_SPEED
FAN_SPEED_CONTROL
1
2
3
4
GND
FA N_VOLTAGE
FA N_SPEED
36
Deutsch
ATX-Netzanschluss
(24-polig, ATXPWR1)
(siehe S. 1, Nr. 8)
Dieses Motherboard bietet
einen 24-poligen ATX-Net-
zanschluss. Bitte schließen
Sie es zur Nutzung eines
20-poligen ATX-Netzteils
entlang Kontakt 1 und
Kontakt 13 an.
ATX-12-V-Netzanschluss
(8-polig, ATX12V1)
(siehe S. 1, Nr. 1)
Dieses Motherboard bietet
einen 8-poligen ATX-12-
V-Netzanschluss. Bitte
schließen Sie es zur Nut-
zung eines 4-poligen ATX-
Netzteils entlang Kontakt 1
und Kontakt 5 an.
Serieller-Port-Stileiste
(9-polig, COM1)
(siehe S. 1, Nr. 24)
Diese COM1-Stileiste
unterstützt ein Modul für
serielle Ports.
TPM-Stileiste
(17-polig, TPMS1)
(siehe S. 1, Nr. 22)
Dieser Anschluss unterstützt das
Trusted Platform Module- (TPM)
System, das Schlüssel, digitale
Zertikate, Kennwörter und Daten
sicher auewahren kann. Ein
TPM-System hil zudem bei der
Stärkung der Netzwerksicherheit,
schützt digitale Identitäten und
gewährleistet die Plattforminteg-
rität.
Druckanschluss-
Stileiste
(25-polig, LPT1)
(siehe S. 1, Nr. 23)
Diese Schnittstelle ist für
Druckerkabel vorgesehen
und ermöglicht bequemes
Anschließen von Druckern.
1
GN D
SM B _DATA_MAIN
LA D 2
LA D 1
GN D
S_ P WRDWN #
SE R IRQ #
GN
D
P C I C L K
P C I R ST #
LA D 3
+3 V
LA D 0
+3VS B
GN D
FR A M E
SM B _CLK_MAIN
12
1
24
13
5
1
8
4
1
AF D #
ER R OR#
PI N IT#
GN D
SL I N#
ST B #
SP D 0
SP D 1
SP D 2
SP D 3
SP D 4
SP D 5
SP D 6
SP D 7
AC K #
BU S Y
PE
SL C T
37
Deutsch
Fatal1ty B250M Performance Series
AURA RGB-LED-
Stileiste
(4-polig, RGB_
HEADER1)
(siehe S. 1, Nr. 7)
AURA RGB-Stileiste
dient dem Anschließen
eines RGB-LED-
Erweiterungskabels, das
dem Nutzer die Auswahl
zwischen verschiedenen
LED-Lichteekten
ermöglicht.
38
Français
1 Introduction
Nous vous remercions d’avoir acheté cette carte mère ASRock Fatal1ty B250M
Performance Series, une carte mère able fabriquée conformément au contrôle de
qualité rigoureux et constant appliqué par ASRock. Fidèle à son engagement de qualité
et de durabilité, ASRock vous garantit une carte mère de conception robuste aux
performances élevées.
1.1 Contenu de l’emballage
•
Carte mère ASRock Fatal1ty B250M Performance Series (facteur de forme Micro ATX)
•
Guide d’installation rapide ASRock Fatal1ty B250M Performance Series
•
CD d’assistance ASRock Fatal1ty B250M Performance Series
•
2 x câbles de données Serial ATA (SATA) (Optionnel)
•
2 x vis pour sockets M.2 (Optionnel)
•
1 x panneau de protection E/S
Les spécications de la carte mère et du logiciel BIOS pouvant être mises à jour, le
contenu de ce document est soumis à modication sans préavis. En cas de modications
du présent document, la version mise à jour sera disponible sur le site Internet ASRock
sans notication préalable. Si vous avez besoin d’une assistance technique pour votre
carte mère, veuillez visiter notre site Internet pour plus de détails sur le modèle que vous
utilisez. La liste la plus récente des cartes VGA et des processeurs pris en charge est égale-
ment disponible sur le site Internet de ASRock. Site Internet ASRock http://www.asrock.
com.
39
Français
Fatal1ty B250M Performance Series
1.2 Spécications
Plateforme
•
Facteur de forme Micro ATX
Processeur
•
Prend en charge les 7
ème
et 6
ème
Générations de processeurs Intel®
Core
TM
i7/i5/i3/Pentium®/Celeron® (Socket 1151)
•
Digi Power design
•
Alimentation à 6 phases
•
Prend en charge la technologie Intel® Turbo Boost 2.0
Chipset
•
Intel® B250
Mémoire
•
Technologie mémoire double canal DDR4
•
4 x fentes DIMM DDR4
•
Prend en charge les mémoires sans tampon non ECC DDR4
2400/2133*
* La 7
ème
Génération de CPU Intel® prend en charge DDR4 jusqu'à
2400 ; la 6
ème
Génération de CPU Intel® prend en charge DDR4
jusqu'à 2133.
•
Prend en charge les modules mémoire UDIMM ECC (fonctionne
en mode non-ECC)
•
Capacité max. de la mémoire système : 64Go
•
Prend en charge Intel® Extreme Memory Prole (XMP) 2.0
•
Contacts dorés 15μ sur fentes DIMM
Fented’-
expansion
•
2 x fentes PCI Express 3.0 x 16 (PCIE1:mode x16 ;
PCIE4:mode x4)*
* Prend en charge les SSD NVMe comme disques de démarrage
•
2 x fentes PCI Express 3.0 x 1 (Flexible PCIe)
•
Prend en charge AMD Quad CrossFireX
TM
et CrossFireX
TM
•
Contact doré 15μ dans fente VGA PCIe (PCIE1)
40
Français
Graphiques
•
La technologie Intel® HD Graphics Built-in Visuals et les sorties
VGA sont uniquement prises en charge par les processeurs
intégrant un contrôleur graphique.
•
Prend en charge la technologie Intel® HD Graphics Built-in
Visuals : Intel® Quick Sync Video avec AVC, MVC (S3D) et
MPEG-2 Full HW Encode1, Intel® InTru
TM
3D, Intel® Clear Video
HD Technology, Intel® Insider
TM
, Intel® HD Graphics
•
Gen9 LP, DX11.3, DX12
•
Codage/Décodage HWA : VP8, HEVC 8b, VP9, HEVC 10b (Pour
la 7
ème
Génération de CPU Intel®)
•
Codage/Décodage HWA : VP8 , HEVC 8b ; Codage/Décodage
GPU/SW : VP9, HEVC 10b (Pour la 6
ème
Génération de CPU
Intel®)
•
Mémoire partagée max. 1024 Mo
* La taille de la mémoire partagée maximale peut varier selon les
diérents systèmes d'exploitation.
•
Trois options de sortie graphique : D-Sub, DVI-D et HDMI
•
Prend en charge la conguration à triple moniteurs
•
Prend en charge la technologie HDMI avec résolution maximale
de 4K x 2K (4096x2160) @ 24Hz / (3840x2160) @ 30Hz
•
Prend en charge le mode DVI-D avec une résolution maximale de
1920x1200 @ 60Hz
•
Prend en charge le mode D-Sub avec une résolution maximale de
1920x1200 @ 60Hz
•
Prend en charge les technologies Auto Lip Sync, Deep Color
(12bpc), xvYCC et HBR (High Bit Rate Audio) avec port HDMI
(un écran compatible HDMI est requis)
•
Prend en charge HDCP via ports DVI-D et HDMI
•
Prend en charge la lecture Blu-ray (BD) Full HD 1080p via ports
DVI-D et HDMI
Audio
•
Audio 7.1 CH HD avec protection du contenu (codec audio
Realtek ALC892)
*Pour congurer l’audio 7.1 CH HD, il est nécessaire d’utiliser un
module audio HD pour panneau frontal et d’activer la fonction audio
multicanal via le pilote audio.
•
Compatible audio Blu-ray Premium
•
Protection contre les surtensions (Protection complète contre les
pics ASRock)
•
Couvercles audio série en or n Nichicon
•
Prend en charge Creative SoundBlaster Cinema3
41
Français
Fatal1ty B250M Performance Series
Réseau
•
Gigabit LAN 10/100/1000 Mo/s
•
Giga PHY Intel® I219V
•
Prend en charge la fonction Wake-On-LAN
•
Protection contre les orages/décharges électrostatiques
(Protection complète contre les pics ASRock)
•
Prend en charge la fonction d’économie d’énergie Ethernet 802.3az
•
Prend en charge PXE
Connectique
du panneau
arrière
•
1 x port souris PS/2
•
1 x port clavier PS/2
•
1 x port D-Sub
•
1 x port DVI-D
•
1 x port HDMI
•
1 x port USB 2.0 (Protection contre les décharges électrostatiques
(Protection complète contre les pics ASRock))
•
1 x port souris Fatal1ty (USB 2.0) (Protection contre les décharges
électrostatiques (Protection complète contre les pics ASRock))
•
3 x ports USB 3.0 type A (Protection contre les décharges
électrostatiques (Protection complète contre les pics ASRock))
•
1 x port USB 3.0 type C (Protection contre les décharges
électrostatiques (Protection complète contre les pics ASRock))
•
1 x port RJ-45 LAN avec LED (LED ACT/LIEN et LED VITESSE)
•
Connecteurs jack audio HD : Entrée ligne / haut-parleur avant /
microphone
Stockage
•
6 x connecteurs SATA3 6,0 Go/s, compatibles NCQ, AHCI et Hot
Plug*
* Si M2_1 est occupé par un périphérique M.2 type SATA, SATA3_0
est désactivé.
•
1 x socket Ultra M.2 (M2_1), prend en charge les modules M.2
SATA3 6,0 Gb/s type 2230/2242/2260/2280 et M.2 PCI Express
jusqu'à Gen3 x4 (32 Gb/s)**
•
1 x socket Ultra M.2 (M2_2), prend en charge les modules M.2
PCI Express type 2230/2242/2260/2280 jusqu'à Gen3 x4 (32 Gb/s)**
** Si l’emplacement PCIE2 ou l’emplacement PCIE3 est occupé,
l’appareil PCIe-type M.2 sur le socket M2_1 fonctionnera à Gen3 x2
(16 Gbit/s).
** Prend en charge Intel® Optane
TM
Technology (M2_2)
** Prend en charge les SSD NVMe comme disques de démarrage
** Prend en charge le kit ASRock U.2
42
Français
Connecteur
•
1 x embase pour port d’impression
•
1 x embase pour port COM
•
1 x embase TPM
•
1 x prise DEL d’alimentation et emplacement sur châssis
•
2 x connecteurs pour ventilateur de processeur (1 x 4 broches,
1 x 3 broches)
* Le connecteur pour ventilateur de CPU prend en charge un
ventilateur de CPU d'une puissance maximale de 1 A (12 W).
•
2 x connecteurs pour ventilateur du châssis (4 broches) (contrôle
de vitesse de ventilateur intelligent)
* CHA_FAN1 et CHA_FAN2 peuvent détecter automatiquement si
un ventilateur 3 broches ou 4 broches est utilisé.
•
1 x connecteur d’alimentation ATX 24 broches
•
1 x connecteur d’alimentation 12V 8 broches
•
1 x connecteur audio panneau frontal
•
2 x embases USB 2.0 (4 ports USB 2.0 pris en charge)
(Protection contre les décharges électrostatiques (Protection
complète contre les pics ASRock))
•
1 x embases USB 3.0 (2 ports USB 3.0 pris en charge)
(Protection contre les décharges électrostatiques (Protection
complète contre les pics ASRock))
Caractéris-
tiques du
BIOS
•
BIOS UEFI AMI avec prise en charge d’interface graphique multi-
lingue
•
Compatible ACPI 6.0 Wake Up Events
•
Compatible SMBIOS 2.7
•
Réglage de la tension CPU, GT_CPU, DRAM, PCH 1.0V,
VCCIO, VCCSA, VCCST
Surveillance
du matériel
•
Détection de la température du processeur/châssis
•
Tachéomètre ventilateur processeur/châssis
•
Ventilateur silencieux processeur/châssis (réglage automatique
de la vitesse du ventilateur du châssis d’après la température du
processeur)
•
Contrôle simultané des vitesses des ventilateurs processeur/châs-
sis
•
Détection CHASSIS OUVERT
•
Surveillance de la tension d’alimentation : +12V, +5V, +3,3V, CPU
Vcore, DRAM, PCH 1,0V
43
Français
Fatal1ty B250M Performance Series
Il est important de signaler que l’overcloking présente certains risques, incluant des
modications du BIOS, l’application d’une technologie d’overclocking déliée et l’utilisation
d’outils d’overclocking développés par des tiers. La stabilité de votre système peut être
aectée par ces pratiques, voire provoquer des dommages aux composants et aux
périphériques du système. L’overclocking se fait à vos risques et périls. Nous ne pour-
rons en aucun cas être tenus pour responsables des dommages éventuels provoqués par
l’overclocking.
Système
d’exploitation
•
Microso® Windows® 10 64 bits (Pour la 7
ème
Génération de CPU
Intel®)
•
Microso® Windows® 10 64 bits / 8.1 64 bits / 7 32 bits / 7 64 bits
(Pour la 6
ème
Génération de CPU Intel®)
* Pour installer Windows® 7, un disque d'installation modié avec
les pilotes xHCI intégrés au chier ISO est requis. Reportez-vous à la
page 153 pour des instructions plus détaillées.
* Pour le pilote mis à jour pour Windows® 10, veuillez visiter le site
Web d'ASRock pour plus de détails: http://www.asrock.com
Certications
•
FCC, CE, WHQL, RCM, BSMI
•
ErP/EuP Ready (alimentation ErP/EuP ready requise)
* pour des informations détaillées de nos produits, veuillez visiter notre site: http://www.asrock.com
44
Français
1.3 Embases et connecteurs de la carte mère
Embase du panneau
système
(PANNEAU1 à 9 broches)
(voir p.1, No. 19)
Branchez le bouton de
mise en marche, le bouton
de réinitialisation et le
témoin d’état du système
présents sur le châssis
sur cette embase en
respectant la conguration
des broches illustrée
ci-dessous. Repérez
les broches positive et
négative avant de brancher
les câbles.
PWRBTN (bouton d’alimentation):
pour brancher le bouton d’alimentation du panneau frontal du châssis. Vous pouvez
congurer la façon dont votre système doit s’arrêter à l’aide du bouton de mise en marche.
RESET (bouton de réinitiélisation):
pour brancher le bouton de réinitialisation du panneau frontal du châssis. Appuyez
sur le bouton de réinitialisation pour redémarrer l’ordinateur en cas de plantage ou de
dysfonctionnement au démarrage.
PLED (LED d’alimentation du système) :
pour brancher le témoin d’état de l’alimentation du panneau frontal du châssis. Le LED
est allumé lorsque le système fonctionne. Le LED clignote lorsque le système se trouve en
mode veille S1/S3. Le LED est éteint lorsque le système se trouve en mode veille S4 ou
hors tension (S5).
HDLED (LED d’activité du disque dur) :
pour brancher le témoin LED d’activité du disque dur du panneau frontal du châssis. Le
LED est allumé lorsque le disque dur lit ou écrit des données.
La conception du panneau frontal peut varier en fonction du châssis. Un module de
panneau frontal est principalement composé d’un bouton de mise en marche, bouton de
réinitialisation, LED d’alimentation, LED d’activité du disque dur, haut-parleur etc. Lor-
sque vous reliez le module du panneau frontal de votre châssis sur cette embase, veillez à
parfaitement faire correspondre les ls et les broches.
Les embases et connecteurs situés sur la carte NE SONT PAS des cavaliers. Ne placez
JAMAIS de capuchons de cavaliers sur ces embases ou connecteurs. Placer un capuchon
de cavalier sur ces embases ou connecteurs endommagera irrémédiablement votre carte
mère.
GND
R ESET#
P WRBTN#
P LED-
P LED+
GND
H DLED-
H DLED+
1
GND
45
Français
Fatal1ty B250M Performance Series
Prise DEL d’alimentation
et emplacement sur châssis
(SPK_CI1 7à broches)
(voir p.1, No. 18)
Veuillez brancher
l'emplacement sur le châs-
sis et le haut-parleur du
châssis sur ce connecteur.
Connecteurs Serial ATA3
(SATA3_0:
voir p.1, No. 10)
(SATA3_1:
voir p.1, No. 11)
(SATA3_2:
voir p.1, No. 13)
(SATA3_3:
voir p.1, No. 14)
(SATA3_4:
voir p.1, No. 16)
(SATA3_5:
voir p.1, No. 15)
Ces six connecteurs
SATA3 sont compatibles
avec les câbles de données
SATA pour les appareils de
stockage internes avec un
taux de transfert maximal
de 6,0 Go/s.
Si M2_1 est occupé par
un périphérique M.2
type SATA, SATA3_0 est
désactivé.
Embases USB 2.0
(USB3_4 à 9 broches)
(voir p.1, No. 21)
(USB5_6 à 9 broches)
(voir p.1, No. 20)
Cette carte mère comprend
deux connecteurs. Chaque
embase USB 2.0 peut
prendre en charge deux
ports.
Embases USB 3.0
(USB3_5_6 à 19 broches)
(voir p.1, No. 9)
Cette carte mère est
dotée d’une embase
supplémentaire. Chaque
embase USB 3.0 peut
prendre en charge deux
ports.
1
IntA_ PB_D +
Dummy
IntA_ PB_D -
GND
IntA_ PB_S ST X +
GND
IntA_ PB_S ST X -
IntA_ PB_S SR X +
IntA_ PB_S SR X -
VbusVbus
Vbus
IntA_ PA_S SR X -
IntA_ PA_S SR X +
GND
IntA_ PA_S ST X -
IntA_ PA_S ST X +
GND
IntA_ PA_D -
IntA_ PA_D +
1
+5V
DUMMY
SIGNAL
GND
DUMMY
SPEAKER
DUMMY
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
USB_PWR
1
SATA3_4
SATA3_5
SATA3_2
SATA3_3
SATA3_1
SATA3_0
46
Français
GND
FAN_VOLTAGE_ CONTROL
FAN_SPEE D
FAN_SPEE D_CONTROL
GND
FA N_VOLTAGE
FA N_SPEED
Embase audio du panneau
frontal
(HD_AUDIO1 à 9
broches)
(voir p.1, No. 25)
Cette embase sert au
branchement des appareils
audio au panneau audio
frontal.
Connecteurs du ventila-
teur du châssis
(CHA_FAN1 à 4 broches)
(voir p.1, No. 2)
(CHA_FAN2 à 4 broches)
(voir p.1, No. 12)
Veuillez brancher les
câbles du ventilateur sur le
connecteur du ventilateur,
puis reliez le l noir à la
broche de mise à terre.
Connecteurs du
ventilateur du
processeur
(CPU_FAN1 à 4 broches)
(voir p.1, No. 3)
(CPU_FAN2 à 3 broches)
(voir p.1, No. 4)
Cette carte mère est dotée
d’un connecteur pour
ventilateur de processeur
(Quiet Fan) à 4 broches.
Si vous envisagez de con-
necter un ventilateur de
processeur à 3 broches,
veuillez le brancher sur la
Broche 1-3.
1. L’audio haute dénition prend en charge la technologie Jack Sensing (détection de la
che), mais le panneau grillagé du châssis doit être compatible avec la HDA pour
fonctionner correctement. Veuillez suivre les instructions gurant dans notre manuel et
dans le manuel du châssis pour installer votre système.
2. Si vous utilisez un panneau audio AC’97, veuillez le brancher sur l’embase audio du
panneau frontal en procédant comme suit :
A. branchez Mic_IN (MIC) sur MIC2_L.
B. branchez Audio_R (RIN) sur OUT2_R et Audio_L (LIN) sur OUT2_L.
C. branchez la mise à terre (GND) sur mise à terre (GND).
D. MIC_RET et OUT_RET sont exclusivement réservés au panneau audio HD. Il est
inutile de les brancher avec le panneau audio AC’97.
E. Pour activer le micro frontal, sélectionnez l’onglet «FrontMic» du panneau de
contrôle Realtek et réglez le paramètre «Volume d’enregistrement».
J _SENSE
O UT2_L
1
M IC_RET
P RESENCE#
GN D
O UT2_R
M IC2_R
M IC2_L
OUT_RET
GND
FAN_VOLTAGE_CO NTROL
FAN_SPEED
FAN_SPEED _CONTROL
FAN_VOLTAGE
GND
FAN_SPEED
FAN_SPEED_CONTROL
1
2
3
4
47
Français
Fatal1ty B250M Performance Series
Connecteur d’alimentation
ATX
(ATXPWR1 à 24 broches)
(voir p.1, No. 8)
Cette carte mère est
dotée d’un connecteur
d’alimentation ATX à 24
broches. Pour utiliser une
alimentation ATX à 20
broches, veuillez eectuer
les branchements sur la
Broche 1 et la Broche 13.
Connecteur d’alimentation
ATX 12V
(ATX12V1 à 8 broches)
(voir p.1, No. 1)
Cette carte mère est
dotée d’un connecteur
d’alimentation ATX 12V
à 8 broches. Pour utiliser
une alimentation ATX à 4
broches, veuillez eectuer
les branchements sur la
Broche 1 et la Broche 5.
Embase pour port série
(COM1 à 9 broches)
(voir p.1, No. 24)
Cette embase COM1 prend
en charge un module de
port série.
Embase TPM
(TPMS1 à 17 broches)
(voir p.1, No. 22)
Ce connecteur prend en charge un
module TPM (Trusted Platform
Module – Module de plateforme
sécurisée), qui permet de sauve-
garder clés, certicats numériques,
mots de passe et données en toute
sécurité. Le système TPM permet
également de renforcer la sécurité
du réseau, de protéger les identités
numériques et de préserver
l’intégrité de la plateforme.
Embase de port
d’impression
(LPT1 à 25 broches)
(voir p.1, No. 23)
Il s’agit d’une interface
pour le câble du port
d’impression qui permet
un branchement aisé
des périphériques
d’impression.
1
GN D
SM B _DATA_MAIN
LA D 2
LA D 1
GN D
S_ P WRDWN #
SE R IRQ #
GN
D
P C I C L K
P C I R ST #
LA D 3
+3 V
LA D 0
+3VS B
GN D
FR A M E
SM B _CLK_MAIN
12
1
24
13
5
1
8
4
1
AF D #
ER R OR#
PI N IT#
GN D
SL I N#
ST B #
SP D 0
SP D 1
SP D 2
SP D 3
SP D 4
SP D 5
SP D 6
SP D 7
AC K #
BU S Y
PE
SL C T
48
Français
Embase LED RGB AURA
(RGB_HEADER1 à 4
broches)
(voir p.1, No. 7)
L'embase RGB sert
à connecter le câble
d'extension LED RVB qui
permet aux utilisateurs de
choisir parmi plusieurs
eets lumineux LED.
49
Italiano
Fatal1ty B250M Performance Series
1 Introduzione
Congratulazioni per l’acquisto della scheda madre ASRock Fatal1ty B250M
Performance Series, una scheda madre adabile prodotta secondo i severissimi
controlli di qualità ASRock. La scheda madre ore eccellenti prestazioni con un
design robusto che si adatta all'impegno di ASRock di orire sempre qualità e durata.
1.1 Contenuto della confezione
•
Scheda madre ASRock Fatal1ty B250M Performance Series (fattore di forma Micro ATX)
•
Guida all'installazione rapida di ASRock Fatal1ty B250M Performance Series
•
CD di supporto ASRock Fatal1ty B250M Performance Series
•
2 x cavi dati Serial ATA (SATA) (opzionali)
•
2 x viti per Socket M.2 (opzionali)
•
1 x mascherina metallica posteriore I/O
Dato che le speciche della scheda madre e del soware BIOS possono essere aggiornate,
il contenuto di questa documentazione sarà soggetto a variazioni senza preavviso. Nel
caso di eventuali modiche della presente documentazione, la versione aggiornata sarà
disponibile sul sito Web di ASRock senza ulteriore preavviso. Per il supporto tecnico
correlato a questa scheda madre, visitare il nostro sito Web per informazioni speciche
relative al modello attualmente in uso. È possibile trovare l'elenco di schede VGA più
recenti e di supporto di CPU anche sul sito Web di ASRock. Sito Web di ASRock http://
www.asrock.com.
50
Italiano
1.2 Speciche
Piattaforma
•
Fattore di forma Micro ATX
CPU
•
Supporta processori 7
th
and 6
th
Generation Intel® Core
TM
i7/i5/i3/
Pentium®/Celeron® (Socket 1151)
•
Digi Power design
•
Potenza a 6 fasi
•
Supporta la tecnologia Intel® Turbo Boost 2.0
Chipset
•
Intel® B250
Memoria
•
Tecnologia memoria DDR4 Dual Channel
•
4 alloggi DIMM DDR4
•
Supporto di memoria DDR4 2400/2133 non-ECC, un-buered*
* 7
th
Gen Intel® CPU supporta DDR4 no a 2400; 6
th
Gen Intel® CPU
supporta DDR4 no a 2133.
•
Supporta moduli di memoria ECC UDIMM (funziona in
modalità non ECC)
•
Capacità max. della memoria di sistema: 64GB
•
Supporto di XMP (Extreme Memory Prole) Intel® 2.0
•
Contatti d’oro 15μ negli alloggi DIMM
Alloggio
diespansione
•
2 x alloggi PCI Express 3.0 x16 (PCIE1:modalità x 16;
PCIE4:modalità x4)*
* Supporto di SSD NVMe come disco d’avvio
•
2 x alloggi PCI Express 3.0 x1 (Flexible PCIe)
•
Supporta AMD Quad CrossFireX
TM
e CrossFireX
TM
•
Contatti d’oro 15μ nell’alloggio VGA PCIe (PCIE1)
51
Italiano
Fatal1ty B250M Performance Series
Graca
•
La videograca integrata della scheda video HD Intel® e le uscite
VGA possono essere supportate soltanto con processori con GPU
integrata.
•
Supporta la videograca integrata della scheda video HD Intel®:
Intel® Quick Sync Video con AVC, MVC (S3D) e MPEG-2
Full HW Encode1, Intel® InTru
TM
3D, Intel® Clear Video HD
Technology, Intel® Insider
TM
, Intel® HD Graphics
•
Gen9 LP, DX11.3, DX12
•
Codica/decodica HWA: VP8, HEVC 8b, VP9, HEVC 10b (per
7
th
Gen Intel® CPU)
•
Codica/decodica HWA: VP8 , HEVC 8b; Codica/decodica
GPU/SW: VP9, HEVC 10b (per 6
th
Gen Intel® CPU)
•
Memoria condivisa max. 1.024MB
* Le dimensioni massime della memoria condivisa possono variare
tra i diversi sistemi operativi.
•
Tre opzioni di output graco: D-Sub, DVI-D e HDMI
•
Supporto di tre monitor
•
Supporta HDMI con risoluzione massima no a 4K x 2K
(4096x2160) a 24Hz / (3840x2160) a 30Hz
•
Supporta DVI-D con una risoluzione max. no a 1920 x 1200 a 60
Hz
•
Supporta D-Sub con una risoluzione max. no a 1920 x 1200 a 60
Hz
•
Supporto delle funzioni Auto Lip Sync, Deep Color (12bpc),
xvYCC e HBR (High Bit Rate Audio) con porta HDMI (è
necessario un monitor compatibile HDMI)
•
Supporto di HDCP con le porte DVI-D e HDMI
•
Supporto di riproduzione Full HD 1080p Blu-ray (BD) con le
porte DVI-D e HDMI
Audio
•
Audio HD a 7.1 canali con Content Protection (codec audio
Realtek ALC892)
* Per congurare l’audio HD 7.1 canali, è necessario utilizzare un
modulo pannello frontale audio HD ed attivare la funzione audio
multicanale tramite il driver audio.
•
Supporto audio Blu-ray Premium
•
Supporto protezione da sovratensione (protezione completa
ASRock dai picchi di corrente)
•
Cappucci audio Nichicon serie Fine Gold
•
Supporta Creative SoundBlaster Cinema3
52
Italiano
LAN
•
LAN Gigabit 10/100/1000 Mb/s
•
Giga PHY Intel® I219V
•
Supporto WOL (Wake-On-LAN)
•
Supporto protezione da fulmini/scariche elettrostatiche (ASRock
Full Spike Protection)
•
Supporto Energy Ecient Ethernet 802.3az
•
Supporto PXE
I/O pannello
posteriore
•
1 x porta mouse PS/2
•
1 x porta tastiera PS/2
•
1 x porta D-Sub
•
1 x porta DVI-D
•
1 x porta HDMI
•
1 x porta USB 2.0 (supporto protezione da scariche elettrostatiche
(ESD) (protezione completa ASRock dai picchi di corrente))
•
1 x Porta mouse Fatal1ty (USB 2.0) (supporto protezione da
scariche elettrostatiche (ESD) (protezione completa ASRock dai
picchi di corrente))
•
3 x porte USB 3.0 di tipo A (supporto protezione da scariche
elettrostatiche (ESD) (protezione completa ASRock dai picchi di
corrente))
•
1 x porta USB 3.0 di tipo C (supporto protezione da scariche
elettrostatiche (ESD) (protezione completa ASRock dai picchi di
corrente))
•
1 x porta LAN RJ-45 con LED (ACT/LINK LED e SPEED LED)
•
Connettori audio HD: Ingresso linea / altoparlante frontale /
microfono
Archiviazione
•
6 x connettori SATA3 6,0 Gb/s, supportano NCQ, AHCI e Hot
Plug*
* Se M2_1 è occupato da un dispositivo M.2 di tipo SATA, SATA3_0
sarà disabilitato.
•
1 x socket Ultra M.2 (M2_1), supporta il modulo M.2 SATA3 6,0
Gb/s di tipo 2230/2242/2260/2280 ed il modulo M.2 PCI Express
no a Gen3 x4 (32 Gb/s)**
•
1 x Socket Ultra M.2 (M2_2), supporta di tipo
2230/2242/2260/2280 il modulo M.2 PCI Express no a Gen3 x4
(32 Gb/s)**
** Se l’alloggio PCIE2 o PCIE3 è occupato, il dispositivo M.2 di tipo
PCIe installato su socket M2_1 sarà eseguito a Gen3 x2 (16 Gb/s).
** Supporta la tecnologia Intel® Optane
TM
(M2_2)
** Supporto di SSD NVMe come disco d’avvio
** Supporta kit ASRock U.2
53
Italiano
Fatal1ty B250M Performance Series
Connettore
•
1 x header porta stampa
•
1 x connettore porta COM
•
1 x connettore TMP
•
1 x collegamento altoparlante e intrusione telaio
•
2 x connettori ventola CPU (1 x 4 pin, 1 x 3 pin)
* Il connettore ventola CPU supporta ventole CPU con potenza
massima di 1A (12W).
•
2 x connettori ventola telaio (4 pin) (Smart Fan Speed Control)
* CHA_FAN1 e CHA_FAN2 sono in grado di rilevare se è in uso una
ventola a 3 pin o 4 a pin.
•
1 x connettore alimentazione ATX 24 pin
•
1 x connettore alimentazione 12V 8-pin
•
1 x connettore audio pannello frontale
•
2 x connettori USB 2.0 (supporto di 4 porte USB 2.0) (supporto
protezione da scariche elettrostatiche (ASRock Full Spike
Protection))
•
1 x connettori USB 3.0 (supporto di 2 porte USB 3.0) (supporto
protezione da scariche elettrostatiche (ASRock Full Spike
Protection))
Funzionalità
BIOS
•
AMI UEFI Legal BIOS con interfaccia di supporto multilingue
•
Eventi di riattivazione conformi a ACPI 6.0
•
Supporto di SMBIOS 2.7
•
Regolazione variabile tensione CPU, GT_CPU, DRAM, PCH 1,0V,
VCCIO, VCCSA, VCCST
Hardware
Monitor
•
Rilevamento temperatura CPU/telaio
•
Tachimetro ventola CPU/telaio
•
Ventola silenziosa CPU/telaio (regolazione automatica velocità in
base alla temperatura della CPU)
•
Ventola CPU/telaio con controllo di varie velocità
•
Rilevamento CASE OPEN
•
Monitoraggio tensione: +12V, +5V, +3,3V, CPU Vcore, DRAM,
PCH 1,0V
54
Italiano
* Per informazioni dettagliate sul prodotto, visitare il nostro sito Web: http://www.asrock.com
Prestare attenzione al potenziale rischio previsto nella pratica di overclocking, inclusa
la regolazione delle impostazioni nel BIOS, l'applicazione di tecnologia di Untied
Overclocking o l'utilizzo di strumenti di overclocking di terze parti. L'overclocking può in-
uenzare la stabilità del sistema o perno provocare danni ai componenti e ai dispositivi
del sistema. Occorre eseguirlo a proprio rischio e spese. Non ci riterremo responsabili per
possibili danni provocati da overclocking.
SO
•
Microso® Windows® 10 64-bit (per 7
th
Gen Intel® CPU)
•
Microso® Windows® 10 64-bit / 8.1 64-bit / 7 32-bit / 7 64-bit
(per 6
th
Gen Intel® CPU)
* Per installare Windows® 7, è necessario un disco di installazione
modicato con i driver xHCI integrati nel le ISO. Fare riferimento a
pagina 153 per altre istruzioni dettagliate.
* Per il driver aggiornato di Windows® 10, visitare il sito ASRock
all’indirizzo: http://www.asrock.com
Certicazioni
•
FCC, CE, WHQL, RCM, BSMI
•
ErP/EuP Ready (è necessaria alimentazione ErP/EuP ready)
55
Italiano
Fatal1ty B250M Performance Series
1.3 Header e connettori sulla scheda
Header sul pannello del
sistema
(PANEL1 a 9 pin)
(vedere pag. 1, n. 19)
Collegare l'interruttore
dell'alimentazione,
l'interruttore di reset e
l'indicatore dello stato del
sistema sullo chassis su
questo header secondo
la seguente assegnazione
dei pin. Annotare i pin
positivi e negativi prima di
collegare i cavi.
PWRBTN (interruttore di alimentazione):
collegare all'interruttore dell'alimentazione sul pannello anteriore dello chassis. È
possibile congurare il modo in cui spegnere il sistema utilizzando l'interruttore
dell'alimentazione.
RESET (interruttore di reset):
collegare all'interruttore di reset sul pannello anteriore dello chassis. Premere
l'interruttore di reset per riavviare il computer se il computer si blocca e non riesce ad
eseguire un normale riavvio.
PLED (LED alimentazione del sistema):
collegare all'indicatore di stato dell'alimentazione sul pannello anteriore dello chassis. Il
LED è acceso quando il sistema è in funzione. Il LED continua a lampeggiare quando
il sistema si trova nello stato di sospensione S1/S3. Il LED è spento quando il sistema si
trova nello stato di sospensione S4 o quando è spento (S5).
HDLED (LED di attività disco rigido):
collegare al LED di attività disco rigido sul pannello anteriore dello chassis. Il LED è
acceso quando il disco rigido sta leggendo o scrivendo dati.
Il design del pannello anteriore può cambiare a seconda dello chassis. Un modulo di pan-
nello anteriore è composto principalmente da interruttore di alimentazione, interruttore
di reset, LED di alimentazione, LED di attività disco rigido, altoparlante, ecc. Quando
si collega il modulo del pannello anteriore dello chassis a questo header, accertarsi che le
assegnazioni del lo e le assegnazioni del pin corrispondano correttamente.
Gli header e i connettori sulla scheda NON sono jumper. NON posizionare cappucci del
jumper su questi header e connettori. Il posizionamento di cappucci del jumper su header
e connettori provocherà danni permanenti alla scheda madre.
GND
R ESET#
P WRBTN#
P LED-
P LED+
GND
H DLED-
H DLED+
1
GND
56
Italiano
Collegamento altoparlante
e intrusione telaio
(SPK_CI1 a 7 pin)
(vedere pag. 1, n. 18)
Collegare l’intrusione tel-
aio e l’altoparlante a questo
collegamento.
Connettori Serial ATA3
(SATA3_0:
vedere pag. 1, n. 10)
(SATA3_1:
vedere pag. 1, n. 11)
(SATA3_2:
vedere pag.1, n. 13)
(SATA3_3:
vedere pag.1, n. 14)
(SATA3_4:
vedere pag.1, n. 16)
(SATA3_5:
vedere pag.1, n. 15)
Questi sei connettori
SATA3 supportano cavi
dati SATA per dispositivi
di archiviazione interna,
con una velocità di
trasferimento dati no a 6,0
Gb/s.
Se M2_1 è occupato da
un dispositivo M.2 di
tipo SATA, SATA3_0 sarà
disabilitato.
Header USB 2.0
(9-pin USB3_4)
(vedere pag. 1, n. 21)
(9-pin USB5_6)
(vedere pag. 1, n. 20)
Ci sono due connettori
su questa scheda madre.
Ciascun header USB 2.0
può supportare due porte.
Header USB 3.0
(USB3_5_6 a 19 pin)
(vedere pag. 1, n. 9)
Questa scheda madre è
dotata di un collettore.
Ciascun header USB 3.0
può supportare due porte.
1
IntA_ PB_D +
Dummy
IntA_ PB_D -
GND
IntA_ PB_S ST X +
GND
IntA_ PB_S ST X -
IntA_ PB_S SR X +
IntA_ PB_S SR X -
VbusVbus
Vbus
IntA_ PA_S SR X -
IntA_ PA_S SR X +
GND
IntA_ PA_S ST X -
IntA_ PA_S ST X +
GND
IntA_ PA_D -
IntA_ PA_D +
1
+5V
DUMMY
SIGNAL
GND
DUMMY
SPEAKER
DUMMY
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
USB_PWR
1
SATA3_4
SATA3_5
SATA3_2
SATA3_3
SATA3_1
SATA3_0
57
Italiano
Fatal1ty B250M Performance Series
Header audio pannello
anteriore
(AUDIO1_HD a 9 pin)
(vedere pag. 1, n. 25)
Questo header serve a
collegare i dispositivi
audio al pannello audio
anteriore.
Connettori ventola telaio
(CHA_FAN1 a 4 pin)
(vedere pag. 1, n. 2)
(CHA_FAN2 a 4 pin)
(vedere pag. 1, n. 12)
Collegare il cavo della
ventola al connettore della
ventola e far corrispondere
il lo nero al pin di terra.
Connettori della ventola
della CPU
(CPU_FAN1 a 4 pin)
(vedere pag. 1, n. 3)
(CPU_FAN2 a 3 pin)
(vedere pag. 1, n. 4)
Questa scheda madre è
dotata di un connettore per
la ventola della CPU (Ven-
tola silenziosa) a 4 pin. Se
si decide di collegare una
ventola della CPU a 3 pin,
collegarla al pin 1-3.
1. L'audio ad alta denizione supporta le funzioni Jack sensing, ma il lo del pannello
sullo chassis deve supportare HDA per funzionare correttamente. Seguire le istruzioni
presenti nel nostro manuale e nel manuale dello chassis per installare il sistema.
2. Se si utilizza un pannello audio AC’97, installarlo sull'header audio del pannello
anteriore seguendo le fasi di seguito:
A. Collegare Mic_IN (MIC) a MIC2_L.
B. Collegare Audio_R (RIN) a OUT2_R e Audio_L (LIN) a OUT2_L.
C. Collegare Ground (GND) a Ground (GND).
D. MIC_RET e OUT_RET servono soltanto per il pannello audio HD. Non è neces-
sario collegarli per il pannello audio AC’97.
Per attivare il microfono anteriore, andare alla scheda “FrontMic” nel pannello di
controllo Realtek e regolare il “Volume di registrazione”.
GND
FAN_VOLTAGE_ CONTROL
FAN_SPEE D
FAN_SPEE D_CONTROL
J _SENSE
O UT2_L
1
M IC_RET
P RESENCE#
GN D
O UT2_R
M IC2_R
M IC2_L
OUT_RET
GND
FAN_VOLTAGE_CO NTROL
FAN_SPEED
FAN_SPEED _CONTROL
FAN_VOLTAGE
GND
FAN_SPEED
FAN_SPEED_CONTROL
1
2
3
4
GND
FA N_VOLTAGE
FA N_SPEED
58
Italiano
Connettore di
alimentazione ATX
(ATXPWR1 a 24 pin)
(vedere pag. 1, n. 8)
Questa scheda madre è
dotata di un connettore
di alimentazione ATX
a 24 pin. Per utilizzare
un'alimentazione ATX a
20 pin, collegarla lungo il
pin 1 e il pin 13.
Connettore di
alimentazione ATX da
12 V
(ATX12V1 a 8 pin)
(vedere pag. 1, n. 1)
Questa scheda madre è
dotata di un connettore
di alimentazione ATX da
12 V a 8 pin. Per utilizzare
un'alimentazione ATX a 4
pin, collegarla lungo il pin
1 e il pin 5.
Header porta seriale
(COM1 a 9 pin)
(vedere pag. 1, n. 24)
Questo header COM1
supporta un modulo di
porta seriale.
Header TPM
(TPMS1 a 17 pin)
(vedere pag. 1, n. 22)
Questo connettore supporta il
sistema Trusted Platform Module
(TPM), che può archiviare in
modo sicuro chiavi, certi-
cati digitali, password e dati. Un
sistema TPM permette anche di
potenziare la sicurezza della rete,
di proteggere identità digitali e
di garantire l'integrità della piat-
taforma.
Header porta di stampa
(LPT1 a 25 pin)
(vedere pag. 1, n. 23)
Si tratta di un'interfaccia
per il cavo della porta di
stampa che consente una
comoda connessione ai
dispositivi della stampante.
1
GN D
SM B _DATA_MAIN
LA D 2
LA D 1
GN D
S_ P WRDWN #
SE R IRQ #
GN
D
P C I C L K
P C I R ST #
LA D 3
+3 V
LA D 0
+3VS B
GN D
FR A M E
SM B _CLK_MAIN
12
1
24
13
5
1
8
4
1
AF D #
ER R OR#
PI N IT#
GN D
SL I N#
ST B #
SP D 0
SP D 1
SP D 2
SP D 3
SP D 4
SP D 5
SP D 6
SP D 7
AC K #
BU S Y
PE
SL C T
59
Italiano
Fatal1ty B250M Performance Series
Collettore LED RGB
AURA
(RGB_HEADER1 a 4 pin)
(vedere pag. 1, n. 7)
Il collettore RGB AURA
viene utilizzato per
collegare la prolunga LED
RGB, che consente agli
utenti di scegliere tra vari
eetti di illuminazione a
LED.
60
Español
1 Introducción
Gracias por comprar la placa base ASRock Fatal1ty B250M Performance Series, una
placa base able fabricada según el rigurosísimo control de calidad de ASRock. Ofrece
un rendimiento excelente con un diseño resistente de acuerdo con el compromiso de
calidad y resistencia de ASRock.
1.1 Contenido del paquete
•
Placa base ASRock Fatal1ty B250M Performance Series (Factor de forma Micro ATX)
•
Guía de instalación rápida de ASRock Fatal1ty B250M Performance Series
•
CD de soporte de ASRock Fatal1ty B250M Performance Series
•
2 x cables de datos Serie ATA (SATA) (Opcional)
•
2 x tornillos para sockets M.2 (Opcional)
•
1 x escudo panel I/O
Ya que las especicaciones de la placa base y el soware del BIOS podrán ser actualiza-
dos, el contenido que aparece en esta documentación estará sujeto a modicaciones sin
previo aviso. Si esta documentación sufre alguna modicación, la versión actualizada
estará disponible en el sitio web de ASRock sin previo aviso. Si necesita asistencia técnica
relacionada con esta placa base, visite nuestro sitio web para obtener información
especíca sobre el modelo que esté utilizando. Podrá encontrar las últimas tarjetas VGA,
así como la lista de compatibilidad de la CPU, en el sitio web de ASRock. Sitio web de
ASRock http://www.asrock.com.
61
Español
Fatal1ty B250M Performance Series
1.2 Especicaciones
Plataforma
•
Factor de forma Micro ATX
CPU
•
Admite la familia de procesadores Intel® Core
TM
i7/i5/i3/Pentium®/
Celeron® (zócalo 1151) de la 7
ª
y 6
ª
generación
•
Digi Power design
•
Diseño de 6 fases de alimentación
•
Admite la tecnología Intel® Turbo Boost 2.0
Conjunto de
chips
•
Intel® B250
Memoria
•
Tecnología de memoria DDR4 de doble canal
•
4 x Ranuras DIMM DDR4
•
Admite memoria sin búfer DDR4 2400/2133 no ECC*
* CPU Intel® de 7
a
generación compatible con DDR4 de hasta 2400;
CPU Intel® de 6
a
generación compatible con DDR4 de hasta 2133.
•
Admite módulos de memoria UDIMM ECC (funcionamiento en
modo no ECC)
•
Capacidad máxima de memoria del sistema: 64GB
•
Admite Perl de memoria extremo de Intel® (XMP) 2.0
•
Contacto 15μ Gold en ranuras DIMM
Expansión
Ranura
•
2 x ranuras PCI Express 3.0 x16 (PCIE1:modo x16; PCIE4:modo
x4)*
* Admite unidad de estado sólido de NVMe como disco de arranque
•
2 x ranuras PCI Express 3.0 x1 (Flexible PCIe)
•
Compatible con AMD Quad CrossFireX
TM
y CrossFireX
TM
•
Contacto 15μGold en ranura VGA PCIe (PCIE1)
62
Español
Grácos
•
Intel® HD Graphics Built-in Visuals y las salidas de VGA son
compatibles únicamente con procesadores con GPU integrado.
•
Admite Intel® HD Graphics Built-in Visuals: Intel® Quick Sync
Video con AVC, MVC (S3D) y MPEG-2 Full HW Encode1, Intel®
InTru
TM
3D, Intel® Clear Video HD Technology, Intel® Insider
TM
,
Intel® HD Graphics
•
Gen9 LP, DX11.3, DX12
•
Codicación y descodicación HWA: VP8, HEVC 8b, VP9,
HEVC 10b (para CPU Intel® de la 7
ª
generación)
•
Codicación y descodicación HWA: VP8, HEVC 8b;
codicación y descodicación GPU/SW: VP9, HEVC 10b (para
CPU Intel® de la 6
ª
generación)
•
Memoria máxima compartida de 1.024MB
* El tamaño de memoria compartida máxima puede variar en función
de los sistemas operativos.
•
Tres opciones de salida de grácos: D-Sub, DVI-D y HDMI
•
Compatible con tres monitores
•
Admite la tecnología HDMI con una resolución máxima de
4K x 2K (4096x2160) a 24Hz / (3840x2160) a 30Hz
•
Compatible con DVI-D con máxima resolución hasta
1920x1200 @ 60Hz
•
Admite D-Sub con una resolución máxima de 1920x1200 a 60 Hz
•
Admite Sincronización automática entre audio y vídeo, color
profundo (12 bpc), xvYCC y HBR (audio de alta tasa de bits) con
puerto HDMI (se necesita un monitor compatible con HDMI)
•
Compatible con función HDCP con puertos DVI-D y HDMI
•
Compatible con reproducción Blu-ray (BD) Full HD de 1080p
con puertos DVI-D y HDMI
Audio
•
7.1 Audio CH HD con Protección de contenido (Realtek ALC892
Audio Codec)
*Para congurar 7.1 Audio CH HD, deberá utilizar un módulo del
panel frontal de audio HD y habilitar la característica de audio
multicanal a través del controlador de audio.
•
Compatible con audio Blu-ray Premium
•
Compatible con protección por sobretensión (protección ASRock
Full Spike)
•
Tapas de audio Nichion de la serie Fine Gold
•
Admite Creative SoundBlaster Cinema3
63
Español
Fatal1ty B250M Performance Series
LAN
•
Gigabit LAN 10/100/1000 Mb/s
•
Giga PHY Intel® I219V
•
Admite la función Reactivación de LAN
•
Admite protección contra rayos y ESD (protección total contra
picos ASRock)
•
Admite Ethernet 802.3az de eciencia energética
•
Admite PXE
E/S en panel
posterior
•
1 x puerto de ratón PS/2
•
1 x puerto de teclado PS/2
•
1 x puerto D-Sub
•
1 x puerto DVI-D
•
1 x puerto HDMI
•
1 x puerto USB 2.0 (compatible con protección contra electricidad
estática (protección ASRock Full Spike))
•
1 x puerto de ratón Fatal1ty (USB 2.0) (compatible con protección
contra electricidad estática (protección ASRock Full Spike))
•
3 x puertos USB 3.0 de tipo A (compatible con protección contra
electricidad estática (protección ASRock Full Spike))
•
1 x puerto USB 3.0 de tipo C (compatible con protección contra
electricidad estática (protección ASRock Full Spike))
•
1 x puerto LAN RJ-45 con LED (LED DE ACTIVIDAD/ENLACE
y LED DE VELOCIDAD)
•
Conector de audio HD: Entrada de línea / Altavoz frontal /
Micrófono
Almacenami-
ento
•
6 x Conectores SATA3 de 6,0 Gb/s, compatibilidad con NCQ,
AHCI y conexión en caliente*
* Si M2_1 se ocupa con un dispositivo M.2 de tipo SATA, SATA3_0
se deshabilitará.
•
1 x Zócalo Ultra M.2 (M2_1) que admite el módulo SATA3 6,0
Gb/s M.2 de tipo 2230/2242/2260/2280 y el módulo PCI Express
M.2 hasta Gen3 x4 (32 Gb/s)**
•
1 x socket Ultra M.2 (M2_1), compatible con el módulo express
M.2 PCI de tipo 2230/2242/2260/2280 hasta Gen3 x4 (32 Gb/s)**
** Si la ranura PCIE2 o la ranura PCIE3 está ocupada, el dispositivo
M.2 de tipo PCIe en el zócalo M2_1 funcionará a Gen3 x2 (16 Gb/s).
** Compatible con la tecnología Optane
TM
de Intel® (M2_2)
** Admite unidad de estado sólido de NVMe como disco de arranque
** Admite el kit U.2 de ASRock
64
Español
Conector
•
1 x Base de conexiones de puerto de impresión
•
1 x Base de conexiones de puerto COM
•
1 x Conector TPM
•
1 x Cabezal de intrusión de chasis y de altavoces
•
2 x Conectores para ventilador de la CPU (1 x 4 contactos, 1 x 3
contactos)
* El conector para ventilador de la CPU admite ventilador de la CPU
con una potencia de ventilador de 1 A (12 W) máxima.
•
2 x Conectores (4 contactos) para el ventilador del chasis (control
de velocidad de ventilador inteligente)
* CHA_FAN1 y CHA_FAN2 se pueden detectar automáticamente si
se usa el ventilador de 3 o 4 pines.
•
1 x Conector de alimentación ATX de 24 contactos
•
1 x Conector de alimentación de 12V de 8 pines
•
1 x Conector de audio en el panel frontal
•
2 x Bases de conexiones USB 2.0 (admite 4 puertos USB 2.0).
Admite protección contra ESD (protección total contra picos
ASRock)
•
1 x Bases de conexiones USB 3.0 (admite 2 puertos USB 3.0).
Admite protección contra ESD (protección total contra picos
ASRock)
Función del
BIOS
•
BIOS legal UEFI AMI compatible con interfaz gráca de usuario
multilingüe
•
Eventos de reactivación compatibles con ACPI 6.0
•
Admite SMBIOS 2.7
•
Multi-ajuste de voltaje de CPU, GT_CPU, DRAM, PCH 1,0V,
VCCIO, VCCSA y VCCST
Monitor de
hardware
•
Método de sensor de temperatura de la CPU/Chasis
•
Tacómetro del ventilador de la CPU/Chasis
•
CPU/Chasis Ventilador silencioso (Ajuste automático de veloci-
dad del ventilador del chasis por temperatura de la CPU)
•
Control multivelocidad del ventilador de la CPU/Chasis
•
Detección de CARCASA ABIERTA
•
Supervisión del voltaje: +12V, +5V, +3,3V, CPU Vcore, DRAM,
PCH 1,0V
65
Español
Fatal1ty B250M Performance Series
* Para obtener información detallada del producto, visite nuestro sitio Web: http://www.asrock.com
Tenga en cuenta que hay un cierto riesgo implícito en las operaciones de aumento de la
velocidad del reloj, incluido el ajuste del BIOS, aplicando la tecnología de aumento de
velocidad liberada o utilizando las herramientas de aumento de velocidad de otros fab-
ricantes. El aumento de la velocidad puede afectar a la estabilidad del sistema e, incluso,
dañar los componentes y dispositivos del sistema. Esta operación se debe realizar bajo su
propia responsabilidad y usted debe asumir los costos. No asumimos ninguna responsabi-
lidad por los posibles daños causados por el aumento de la velocidad del reloj.
SO
•
Microso® Windows® 10 64 bits (para CPU Intel® de la 7
a
)
•
Microso® Windows® 10 64 bits / 8.1 64 bits / 7 32 bits / 7 64 bits
(para CPU Intel® de la 6
a
generación)
* Para instalar el sistema operativo Windows® 7, se necesita un disco
de instalación modicado con los controladores xHCI empaquetados
en el archivo ISO. Consulte la página 153 para obtener información
más detallada.
* Para obtener el controlador actualizado para Windows® 10, visite el
sitio Web desde ASRock para obtener detalles:
http://www.asrock.com
Certica-
ciones
•
FCC, CE, WHQL, RCM y BSMI
•
Compatible con ErP/EuP (requiere toma de alimentación
compatible con ErP/EuP)
66
Español
1.3 Conectores y cabezales incorporados
Cabezal del panel del
sistema
(PANEL1 de 9 pines)
(consulte la pág.1, n.º 19)
Conecte el interruptor de
alimentación, restablezca el
interruptor y el indicador
del estado del sistema del
chasis a los valores de este
cabezal, según los valores
asignados a los pines como
se indica a continuación.
Cerciórese de cuáles son
los pines positivos y los
negativos antes de conectar
los cables.
PWRBTN (Interruptor de alimentación):
Conéctelo al interruptor de alimentación del panel frontal del chasis. Deberá congurar
la forma en la que su sistema se apagará mediante el interruptor de alimentación.
RESET (Interruptor de reseteo):
Conéctelo al interruptor de reseteo del panel frontal del chasis. Pulse el interruptor de
reseteo para resetear el ordenador si éste está bloqueado y no se puede reiniciar de forma
normal.
PLED (Indicador LED de la alimentación del sistema):
Conéctelo al indicador de estado de la alimentación del panel frontal del chasis. El indi-
cador LED permanece encendido cuando el sistema está funcionando. El indicador LED
parpadea cuando el sistema se encuentra en estado de suspensión S1/S3. El indicador
LED se apaga cuando el sistema se encuentra en estado de suspensión S4 o está apagado
(S5).
HDLED (Indicador LED de actividad en el disco duro):
Conéctelo al indicador LED de actividad en el disco duro del panel frontal del chasis. El
indicador LED permanece encendido cuando el disco duro está leyendo o escribiendo
datos.
El diseño del panel frontal puede ser diferente dependiendo del chasis. Un módulo de
panel frontal consta principalmente de: interruptor de alimentación, interruptor de
reseteo, indicador LED de alimentación, indicador LED de actividad en el disco duro,
altavoz, etc. Cuando conecte su módulo del panel frontal del chasis a este cabezal, aseg-
úrese de que las asignaciones de los cables y los pines coinciden correctamente.
Los cabezales y conectores incorporados NO son puentes. NO coloque tapas de puente so-
bre estos cabezales y conectores. Si coloca tapas de puente sobre los cabezales y conectores
dañará de forma permanente la placa base.
GND
R ESET#
P WRBTN#
P LED-
P LED+
GND
H DLED-
H DLED+
1
GND
67
Español
Fatal1ty B250M Performance Series
Cabezal de intrusión de
chasis y de altavoces
(SPK_CI1 de 7 pines)
(consulte la pág.1, nº 18)
Conecte la intrusión de
chasis y el altavoz del
chasis a este cabezal.
Conectores Serie ATA3
(SATA3_0:
consulte la pág.1, n.º 10)
(SATA3_1:
consulte la pág.1, n.º 11)
(SATA3_2:
consulte la pág.1, n.º 13)
(SATA3_3:
consulte la pág.1, n.º 14)
(SATA3_4:
consulte la pág.1, n.º 16)
(SATA3_5:
consulte la pág.1, n.º 15)
Estos seis conectores
SATA3 son compatibles
con cables de datos SATA
para dispositivos de
almacenamiento interno
con una velocidad de
transferencia de datos de
hasta 6,0 Gb/s.
Si M2_1 se ocupa con
un dispositivo M.2 de
tipo SATA, SATA3_0 se
deshabilitará.
Cabezales USB 2.0
(USB3_4 de 9 pines)
(consulte la pág.1, nº 21)
(USB5_6 de 9 pines)
(consulte la pág.1, nº 20)
Hay dos bases de
conexiones en esta placa
base. Cada cabezal USB 2.0
admite dos puertos.
Cabezal USB 3.0
(USB3_5_6 de 19 pines)
(consulte la pág.1, nº 9)
Esta placa base contiene un
cabezal. Cada cabezal USB
3.0 admite dos puertos.
1
IntA_ PB_D +
Dummy
IntA_ PB_D -
GND
IntA_ PB_S ST X +
GND
IntA_ PB_S ST X -
IntA_ PB_S SR X +
IntA_ PB_S SR X -
VbusVbus
Vbus
IntA_ PA_S SR X -
IntA_ PA_S SR X +
GND
IntA_ PA_S ST X -
IntA_ PA_S ST X +
GND
IntA_ PA_D -
IntA_ PA_D +
1
+5V
DUMMY
SIGNAL
GND
DUMMY
SPEAKER
DUMMY
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
USB_PWR
1
SATA3_4
SATA3_5
SATA3_2
SATA3_3
SATA3_1
SATA3_0
68
Español
GND
FAN_VOLTAGE_ CONTROL
FAN_SPEE D
FAN_SPEE D_CONTROL
GND
FA N_VOLTAGE
FA N_SPEED
Cabezal de audio del panel
frontal
(HD_AUDIO1 de 9 pines)
(consulte la pág.1, nº 25)
Este cabezal se utiliza para
conectar dispositivos de
audio al panel de audio
frontal.
Conectores para el venti-
lador del chasis
(CHA_FAN1 de 4 pines)
(consulte la pág.1, n.º 2)
(CHA_FAN2 de 4 pines)
(consulte la pág.1, n.º 12)
Conecte el cable del
ventilador al conector del
ventilador y haga coincidir
el cable negro con el pin de
conexión a tierra.
Conectores del ventilador
de la CPU
(CPU_FAN1 de 4 pines)
(consulte la pág.1, n.º 3)
(CPU_FAN2 de 3 pines)
(consulte la pág.1, N.º 4)
Esta placa base contiene
un conector de ventilador
(ventilador silencioso) de
CPU de 4 pines. Si tiene
pensando conectar un ven-
tilador de CPU de 3 pines,
conéctelo al Pin 1-3.
1. El Audio de Alta Denición (HDA, en inglés) es compatible con el método de sensor de
conectores, sin embargo, el cable del panel del chasis deberá ser compatible con HDA
para que pueda funcionar correctamente. Siga las instrucciones que se indican en
nuestro manual y en el manual del chasis para instalar su sistema.
2. Si utiliza un panel de audio AC’97, colóquelo en el cabezal de audio del panel frontal
siguiendo los pasos que se describen a continuación:
A. Conecte Mic_IN (MIC) a MIC2_L.
B. Conecte Audio_R (RIN) a OUT2_R y Audio_L (LIN) a OUT2_L.
C. Conecte Ground (Conexión a tierra) (GND) a Ground (GND).
D. MIC_RET y OUT_RET se utilizan únicamente con el panel de audio HD. No es
necesario que los conecte en el panel de audio AC’97.
E. Para activar el micrófono frontal, vaya a la cha “micrófono frontal” (FrontMic) en
el panel de control de Realtek y ajuste el “Volumen de grabación” (Recording Volume).
J _SENSE
O UT2_L
1
M IC_RET
P RESENCE#
GN D
O UT2_R
M IC2_R
M IC2_L
OUT_RET
GND
FAN_VOLTAGE_CO NTROL
FAN_SPEED
FAN_SPEED _CONTROL
FAN_VOLTAGE
GND
FAN_SPEED
FAN_SPEED_CONTROL
1
2
3
4
69
Español
Fatal1ty B250M Performance Series
Conector de alimentación
ATX
(ATXPWR1 de 24 pines)
(consulte la pág.1, nº 8)
Esta placa base contiene
un conector de aliment-
ación ATX de 24 pines.
Para utilizar una toma
de alimentación ATX de
20 pines, conéctela en los
Pines del 1 al 13.
Conector de alimentación
ATX de 12V
(ATX12V1 de 8 pines)
(consulte la pág.1, nº 1)
Esta placa base contiene
un conector de aliment-
ación ATX de 12V y 8
pines. Para utilizar una
toma de alimentación ATX
de 4 pines, conéctela en los
Pines del 1 al 5.
Cabezal de puerto serie
(COM1 de 9 pines)
(consulte la pág.1, nº 24)
Este cabezal COM1 admite
un módulo de puerto serie.
Cabezal TPM
(TPMS1 de 17 pines)
(consulte la pág.1, nº 22)
Este conector es compatible con el
sistema Módulo de Plataforma
Segura (TPM, en inglés), que
puede almacenar de forma
segura claves, certicados
digitales, contraseñas y datos.
Un sistema TPM también ayuda
a aumentar la seguridad en la red,
protege las identidades digitales
y garantiza la integridad de la
plataforma.
Cabezal de puerto de
impresión
(LPT1 de 25 pines)
(consulte la pág.1, nº 23)
Ésta es una interfaz para
el cable del puerto de
impresión que permite
una cómoda conexión de
dispositivos de impresión.
1
GN D
SM B _DATA_MAIN
LA D 2
LA D 1
GN D
S_ P WRDWN #
SE R IRQ #
GN
D
P C I C L K
P C I R ST #
LA D 3
+3 V
LA D 0
+3VS B
GN D
FR A M E
SM B _CLK_MAIN
12
1
24
13
5
1
8
4
1
AF D #
ER R OR#
PI N IT#
GN D
SL I N#
ST B #
SP D 0
SP D 1
SP D 2
SP D 3
SP D 4
SP D 5
SP D 6
SP D 7
AC K #
BU S Y
PE
SL C T
70
Español
Cabezal de LED RGB
AURA
(RGB_HEADER1 de 4
pines)
(consulte la pág.1, nº 7)
El cabezal RGB AURA se
utiliza para conectar el
alargador de LED RGB
que permite a los usuarios
elegir entre varios efectos
de iluminación de LED.
71
Русский
Fatal1ty B250M Performance Series
1 Введение
Благодарим вас за приобретение надежной материнской платы ASRock Fatal1ty
B250M Performance Series, выпускаемой под постоянным строгим контролем
компании ASRock. Эта материнская плата обеспечивает великолепную
производительность и характеризуется прочной конструкцией в соответствии с
требованиями компании ASRock в отношении качества и долговечности.
1.1 Комплект поставки
•
Материнская плата ASRock Fatal1ty B250M Performance Series (форм-фактор Micro
ATX)
•
Краткое руководство по установке ASRock Fatal1ty B250M Performance Series
•
Диск с ПО для ASRock Fatal1ty B250M Performance Series
•
2 х кабеля передачи данных Serial ATA (SATA) (приобретаются отдельно)
•
2 x Винт для гнезда M.2 (приобретаются отдельно)
•
1 х экран панели с портами ввода-вывода
По причине обновления спецификации на материнскую платформу и
программного обеспечения BIOS содержимое настоящей документации может
быть изменено без предварительного уведомления. При изменении содержимого
настоящего документа его обновленная версия будет доступна на веб-сайте
ASRock без предварительного уведомления. При необходимости технической
поддержки, связанной с материнской платой, посетите веб-сайт и найдите
на нем информацию о модели используемой вами материнской платы. На веб-
сайте ASRock также можно найти самый последний перечень поддерживаемых
VGA-карт и ЦП. Веб-сайт ASRock http://www.asrock.com.
72
Русский
1.2. Технические характеристики
Платформа
•
Форм-фактор Micro ATX
ЦП
•
Поддерживаются процессоры Intel® Core
TM
7/i5/i3/Pentium®/
Celeron® (разъем 1151) 7-го и 6-го поколений.
•
Digi Power design
•
Система питания 6
•
Поддерживается технология Intel® Turbo Boost 2.0
Чипсет
•
Intel® B250
Память
•
Двухканальная память DDR4
•
4 x гнезда DDR4 DIMM
•
Поддерживаются модули небуферизованной памяти DDR4
2400/2133 без ECC*
* ЦП Intel® 7-го поколения поддерживают память DDR4 с
частотой до 2400МГц; ЦП Intel® 6-го поколения поддерживают
память DDR4 с частотой до 2133МГц.
•
Поддержка модулей памяти ECC UDIMM (работа в режиме,
отличном от ЕСС)
•
Максимальный объем ОЗУ: 64 Гб
•
Поддерживается Intel® Extreme Memory Prole (XMP) 2.0
•
Гнезда DIMM с золочеными контактами 15мк
Гнезда
расширения
•
2 x слота PCI Express 3.0 x16 (PCIE1:режим x16;
PCIE4:режим x4)*
* Поддерживаются в качестве загрузочных SSD-диски типа
NVMe.
•
2 x PCI Express 3.0 x1 гнезд (Flexible PCIe)
•
Поддержка AMD Quad CrossFireX
TM
и CrossFireX
TM
•
15μ Золоченые контакты разъема VGA PCIe (PCIE1)
73
Русский
Fatal1ty B250M Performance Series
Графическая
подсистема
•
Встроенный видеоадаптер Intel® HD Graphics и выходы
VGA поддерживаются только при использовании ЦП со
встроенными графическими процессорами.
•
Поддерживаемые встроенные технологии визуализации Intel®
HD Graphics: Intel® Quick Sync Video с полностью аппаратным
кодированием1 в форматах AVC, MVC (S3D) и MPEG-2, Intel®
InTru
TM
3D, технология Intel® Clear Video HD, Intel® Insider
TM
,
Intel® HD Graphics
•
Gen9 LP, DX11.3, DX12
•
Программно-аппаратное кодирование-декодирование: VP8,
HEVC 8b, VP9, HEVC 10b (для ЦП Intel® 7-го поколения)
•
Программно-аппаратное кодирование-декодирование:
VP8 , HEVC 8b. Кодирование-декодирование с помощью
графического процессора и программных средств: VP9,
HEVC 10b (для ЦП Intel® 6-го поколения)
•
Максимальный объем общей памяти: 1024МБ
* Максимальный объем общей памяти зависит от операционной
системы.
•
Три видеовыхода: D-Sub, DVI-D и HDMI
•
Поддержка работы с тремя мониторами
•
Поддерживается HDMI с максимальным разрешением до
4K x 2K (4096x2160) при частоте обновления 24 Гц
(3840x2160 при 30Гц)
•
Поддержка DVI-D с максимальным разрешением до
1920x1200 при 60 Гц
•
Поддерживается D-Sub с максимальным разрешением до
1920x1200 при 60 Гц
•
Поддерживаются Auto Lip Sync, Deep Color (12 бит/цвет),
xvYCC и HBR (High Bit Rate Audio) через порт HDMI
(требуется соответствующий HDMI-монитор)
•
Поддержка функции защиты HDCP через порты DVI-D и
HDMI
•
Поддержка воспроизведения в режиме Full HD 1080p Blu-ray
(BD) через порты DVI-D и HDMI
Звук
•
7.1-канальный звук высокой четкости HD Audio с защитой
данных (аудиокодек Realtek ALC892)
*Для настройки 7.1-канального звук высокой четкости HD
Audio используйте переднюю аудиопанель HD и активируйте
функцию многоканального звука в аудиодрайвере.
•
Поддержка Premium Blu-ray Audio
•
Защита от перенапряжения (ASRock Full Spike Protection)
•
Конденсаторы для аудиосистем серии Nichicon Fine Gold
•
Поддержка Creative SoundBlaster Cinema3
74
Русский
ЛВС
•
Gigabit Ethernet 10/100/1000 Мбит/с
•
Giga PHY Intel® I219V
•
Поддерживается пробуждение по ЛВС
•
Молниезащита и защита от электростатических разрядов
(ASRock Full Spike Protection)
•
Поддерживается Energy Ecient Ethernet 802.3az
•
Поддерживается PXE
Порты ввода-
вывода
на задней
панели
•
1 x порт PS/2 для мыши
•
1 x PS/2 для клавиатуры
•
1 x порт D-Sub
•
1 x порт DVI-D
•
1 x порт HDMI
•
1 x порты USB 2.0 с защитой от электростатического
напряжения (ASRock Full Spike Protection)
•
1 x Порт для мыши Fatal1ty (USB 2.0) с защитой от
электростатического напряжения (ASRock Full Spike
Protection)
•
3 x порты USB 3.0 тип А с защитой от электростатического
напряжения (ASRock Full Spike Protection)
•
1 x порт USB 3.0 типа С с защитой от электростатических
разрядов (ASRock Full Spike Protection)
•
1 x порт ЛВС RJ-45 с индикаторами («Активность/
Соединение» и «Скорость»)
•
Разъемы HD Audio: Линейный вход / передние динамики /
микрофон
Запоминающие
устройства
•
6 x разъемов SATA3 с пропускной способностью 6,0Гбит/с,
поддержка NCQ, AHCI и «горячего» подключения*
* Если слот M2_1 занят устройством М.2 типа SATA, интерфейс
SATA3_0 будет отключен.
•
1 x слот Ultra M.2 (M2_1), поддерживает модуль M.2 SATA3
типа 2230/2242/2260/2280 с пропускной способностью
6,0Гбит/с и модуль M.2 PCI Express до версии Gen3 x4
(32Гбит/с)**
•
1 x Ultra M.2 Socket (M2_2), поддержка модуля M.2 PCI Ex-
press типа 2230/2242/2260/2280 до версии Gen3 x4 (32 ГБ/с)**
** Если слот PCIE2 или слот PCIE3 занят, устройство типа PCIe
M.2 в слоте M2_1 будет работать в режиме Gen3 x2 (16 Гбит/с).
** Поддержка технологии Intel® Optane
TM
(M2_2)
** Поддерживаются в качестве загрузочных SSD-диски типа
NVMe.
** Поддерживается комплект ASRock U.2.
75
Русский
Fatal1ty B250M Performance Series
Разъемы
•
1 x колодка порта принтера
•
1 x колодка СОМ-порта
•
1 x колодка ТРМ
•
1 x колодка с разъемами датчика вскрытия корпуса и
динамика
•
2 x разъема для вентилятора ЦП (1 х 4-контактный,
1 х 3-контактный)
* Разъем процессорного вентилятора поддерживает вентилятор
с потребляемым током не более 1А (12Вт).
•
2 x Разъемы для вентилятора корпуса (4-контактный)
("Умный" регулятор скорости вентилятора)
* Для разъемов CHA_FAN1 и CHA_FAN2 автоматически
определяется тип подключенного вентилятора: 3- или
4-контактный.
•
1 x разъем питания АТХ (24-контактный)
•
1 x 8-контактный разъем питания 12 В
•
1 x аудиоразъем на передней панели
•
2 x колодки USB 2.0 (4 порта USB 2.0) с защитой от
электростатических разрядов (ASRock Full Spike Protection)
•
1 x колодки USB 3.0 (2 порта USB 3.0) с защитой от
электростатических разрядов (ASRock Full Spike Protection)
Параметры
BIOS
•
AMI UEFI Legal BIOS с поддержкой многоязычного
графического интерфейса
•
Поддержка функций пробуждения по стандарту ACPI 6.0
•
Поддерживается SMBIOS 2.7
•
Регулировка напряжений ЦП, GT_CPU, DRAM, PCH 1.0V,
VCCIO, VCCSA, VCCST
Контроль
оборудования
•
Датчик температуры процессора/корпуса
•
Тахометр вентилятора процессора/корпуса
•
Бесшумный вентилятор охлаждения процессора/корпуса
(с автоматической регулировкой скорости вращения в
зависимости от температуры нагрева процессора)
•
Управление скоростью вращения вентилятора охлаждения
процессора/корпуса
•
Датчик вскрытия корпуса
•
Контроль напряжений: +12В, +5В, +3,3В, напряжение ядра
ЦП, DRAM, PCH 1,0В
76
Русский
* С дополнительной информацией об изделии можно ознакомиться на веб-сайте: http://www.asrock.com
Следует учитывать, что разгон процессора, включая изменение настроек BIOS,
применение технологии Untied Overclocking и использование инструментов
разгона независимых производителей, сопряжен с определенным риском. Разгон
процессора может снизить стабильность системы или даже привести к
повреждению ее компонентов и устройств. Разгон процессора осуществляется
пользователем на собственный риск и за собственный счет. Мы не несем
ответственность за возможный ущерб, вызванный разгоном процессора.
Операционные
системы
•
Microso® Windows® 10 64-разрядная (для ЦП Intel® 7-го
поколения)
•
Microso® Windows® 10 64-разрядная / 8.1 64-разрядная/ 7
32-разрядная/ 7 64-разрядная (для ЦП Intel® 6-го поколения)
* Для установки ОС Windows® 7 потребуется измененный
установочный диск с драйверами xHCI, упакованными в файл
ISO. Более подробные инструкции представлены на стр. 153.
* Подробные сведения об обновлении драйвера для Windows® 10
представлены на веб-сайте ASRock: http://www.asrock.com
Сертификация
•
FCC, CE, WHQL, RCM, BSMI
•
Совместимость с ErP/EuP (необходим блок питания,
соответствующий стандарту ErP/EuP)
77
Русский
Fatal1ty B250M Performance Series
1.3 Колодки и разъемы, расположенные на
материнской плате
Колодка системной
панели
(9-контактная, PANEL1)
(См. стр. 1, № 19)
Подключите
расположенные на
корпусе выключатель
питания, кнопку
перезагрузки и
индикатор состояния
системы к этой колодке
в соответствии с
распределением
контактов,
приведенным ниже.
Перед подключением
кабелей определите
положительный
и отрицательный
контакты.
PWRBTN (кнопка питания):
Подключение кнопки питания, расположенной на передней панели корпуса.
Можно настроить порядок выключения системы с использованием кнопки
питания.
RESET (кнопка перезагрузки):
Подключение кнопки перезагрузки системы, расположенной на передней панели
корпуса. Нажмите кнопку перезагрузки, чтобы перезапустить компьютер, если
он завис и нормальный запуск невозможен.
PLED (светодиодный индикатор питания системы):
Подключение индикатора состояния, расположенного на передней панели
корпуса. Светодиодный индикатор горит, когда система работает. Когда
система находится в режиме ожидания S1/S3, светодиод мигает. Когда система
находится в режиме ожидания S4 или выключена (S5), светодиод не горит.
HDLED (светодиодный индикатор работы жесткого диска):
Подключение светодиодного индикатора работы жесткого диска,
расположенного на передней панели. Светодиодный индикатор горит, когда
жесткий диск выполняет считывание или запись данных.
Передняя панель может быть разной на разных корпусах. В основном передняя
панель включает в себя кнопку питания, кнопку перезагрузки, светодиодный
индикатор питания, светодиодный индикатор работы жесткого диска,
динамик и т. д. При подключении передней панели к этой колодке правильно
подключайте провода к контактам.
Расположенные на материнской плате колодки и разъемы перемычками
НЕ являются. НЕ устанавливайте на эти колодки и разъемы колпачковые
перемычки. Установка колпачковых перемычек на эти колодки и разъемы может
вызвать неустранимое повреждение материнской платы.
GND
R ESET#
P WRBTN#
P LED-
P LED+
GND
H DLED-
H DLED+
1
GND
78
Русский
Колодка с разъемами
датчика вскрытия
корпуса и динамика
(7-контактный SPK_CI1)
(См. стр. 1, № 18)
Предназначена для
подключения датчика
вскрытия корпуса и
корпусного динамика.
Разъемы Serial ATA3
(SATA3_0:
См. стр. 1, № 10)
(SATA3_1:
См. стр. 1, № 11)
(SATA3_2:
см. стр.1, № 13)
(SATA3_3:
см. стр.1, № 14)
(SATA3_4:
см. стр.1, № 16)
(SATA3_5:
см. стр.1, № 15)
Эти шесть
разъемов SATA3
предназначены для
подключения кабелей
SATA внутренних
запоминающих
устройств для передачи
данных со скоростью до
6,0 Гб/с.
Если разъем M2_1 занят
устройством М.2 типа
SATA, разъем SATA3_0
будет отключен.
Колодки USB 2.0
(9-контактная USB3_4)
(См. стр. 1, № 21)
(9-контактная USB5_6)
(См. стр. 1, № 20)
На системной плате
размещены две колодки.
Каждая колодка USB 2.0
может поддерживать два
порта.
Колодка USB 3.0
(19-контактная,
USB3_5_6)
(См. стр. 1, № 9)
На системной плате
размещены одна
колодки. Каждая
колодка USB 3.0 может
поддерживать два порта.
1
IntA_ PB_D +
Dummy
IntA_ PB_D -
GND
IntA_ PB_S ST X +
GND
IntA_ PB_S ST X -
IntA_ PB_S SR X +
IntA_ PB_S SR X -
VbusVbus
Vbus
IntA_ PA_S SR X -
IntA_ PA_S SR X +
GND
IntA_ PA_S ST X -
IntA_ PA_S ST X +
GND
IntA_ PA_D -
IntA_ PA_D +
1
+5V
DUMMY
SIGNAL
GND
DUMMY
SPEAKER
DUMMY
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
USB_PWR
1
SATA3_4
SATA3_5
SATA3_2
SATA3_3
SATA3_1
SATA3_0
79
Русский
Fatal1ty B250M Performance Series
GND
FAN_VOLTAGE_ CONTROL
FAN_SPEE D
FAN_SPEE D_CONTROL
GND
FA N_VOLTAGE
FA N_SPEED
Аудиоколодка передней
панели
(9-контактная, HD_
AUDIO1)
(См. стр. 1, № 25)
Эта колодка
предназначена
для подключения
аудиоустройств к
передней аудиопанели.
Разъемы вентиляторов
корпуса
(4-контактный,
CHA_FAN1)
(См. стр. 1, № 2)
(4-контактный,
CHA_FAN2)
(См. стр. 1, № 12)
Предназначен для
подключения кабеля
разъема вентилятора и
подключения черного
провода к заземлению.
Разъемы вентиляторов
ЦП
(4-контактный,
CPU_FAN1)
(См. стр. 1, № 3)
(3-контактный,
CPU_FAN2)
(См. стр. 1, № 4)
Эта материнская
плата снабжена
4-контактным разъемом
для малошумящего
вентилятора ЦП. Если вы
собираетесь подключить
3-контактный
вентилятор охлаждения
процессора, подключайте
его к контактам 1-3.
1. Аудиосистема высокого разрешения поддерживает функцию распознавания
разъема, но для е правильной работы необходимо, чтобы провод панели
корпуса поддерживал передачу сигналов HDA. Инструкции по установке
системы см. в этом руководстве и руководстве на корпус.
2. При использовании аудиопанели AC’97 подключите ее к аудиоколодке передней
панели, как указано далее:
A. Подключите Mic_IN (MIC) к MIC2_L.
B. Подключите Audio_R (RIN) к OUT2_R, Audio_L (LIN) к OUT2_L.
C. Подключите провод заземления (GND) к контакту заземления (GND).
D. Контакты MIC_RET и OUT_RET используются только для аудиопанели
высокого разрешения. При использовании аудиопанели AC’97 их подключать не
нужно.
E. Чтобы активировать передний микрофон, перейдите на вкладку FrontMic
панели управления Realtek и отрегулируйте параметр Recording Volume
(Громкость записи).
J _SENSE
O UT2_L
1
M IC_RET
P RESENCE#
GN D
O UT2_R
M IC2_R
M IC2_L
OUT_RET
GND
FAN_VOLTAGE_CO NTROL
FAN_SPEED
FAN_SPEED _CONTROL
FAN_VOLTAGE
GND
FAN_SPEED
FAN_SPEED_CONTROL
1
2
3
4
80
Русский
Разъем питания АТХ
(24-контактный,
ATXPWR1)
(См. стр. 1, № 8)
Эта материнская плата
снабжена 24-контактным
разъемом питания АТХ.
Чтобы использовать
20-контактный
разъем питания ATX,
подключите его вдоль
контакта 1 и контакта 13.
Разъем питания АТХ 12 В
(8-контактный, ATX
12В 1)
(См. стр. 1, № 1)
Эта материнская плата
снабжена 8-контактным
разъемом питания АТХ
12 В. Чтобы использовать
4-контактный
разъем питания ATX,
подключите его вдоль
контакта 1 и контакта 5.
Колодка
последовательного порта
(9-контактная, COM1)
(См. стр. 1, № 24)
Колодка COM1
поддерживает
подключение модуля
последовательного
порта.
Колодка ТРМ
(17-контактная, TPMS1)
(См. стр. 1, № 22)
Этот разъем обеспечивает
поддержку системы Trusted
Platform Module (TPM), которая
способна обеспечить надежное
хранение ключей, цифровых
сертификатов, паролей и
данных. Система ТРМ также
повышает уровень сетевой
безопасности, защищает
цифровые идентификаторы
и обеспечивает целостность
платформы.
Колодка порта принтера
(25-контактная, LPT1)
(См. стр. 1, № 23)
Это — интерфейс для
подключения кабеля
порта принтера,
обеспечивающий
удобное подключение
устройств печати.
1
GN D
SM B _DATA_MAIN
LA D 2
LA D 1
GN D
S_ P WRDWN #
SE R IRQ #
GN
D
P C I C L K
P C I R ST #
LA D 3
+3 V
LA D 0
+3VS B
GN D
FR A M E
SM B _CLK_MAIN
12
1
24
13
5
1
8
4
1
AF D #
ER R OR#
PI N IT#
GN D
SL I N#
ST B #
SP D 0
SP D 1
SP D 2
SP D 3
SP D 4
SP D 5
SP D 6
SP D 7
AC K #
BU S Y
PE
SL C T
81
Русский
Fatal1ty B250M Performance Series
Колодка светодиодной
RGB-подсветки AURA
(4-контактная, RGB_
HEADER1)
(См. стр. 1, № 7)
Колодка RGB-
подсветки AURA служит
для подключения
удлинительного кабеля
светодиодной RGB-
подсветки, которая
позволяет реализовать
различные световые
эффекты.
82
Português
1 Introdução
Obrigado por adquirir a placa mãe ASRock Fatal1ty B250M Performance Series, uma
conável placa mãe ASRock produzida sob rigoroso controle de qualidade consistente.
Esta placa principal oferece um excelente desempenho com um design robusto em
conformidade com o compromisso da ASRock em fabricar produtos de qualidade e
resistentes.
1.1 Conteúdo da embalagem
•
Placa-mãe ASRock Fatal1ty B250M Performance Series (Micro ATX Form Factor)
•
Guia de Instalação Rápida da ASRock Fatal1ty B250M Performance Series
•
CD de Suporte ASRock Fatal1ty B250M Performance Series
•
2 x Cabos de dados Serial ATA (SATA) (Opcional)
•
2 x Parafusos para Soquetes M.2 (Opcional)
•
1 x Painel de E/S
Como as especicações da placa-mãe e do soware do BIOS podem ser atualizadas, o
conteúdo desta documentação estará sujeito a alterações sem aviso prévio. Caso ocor-
ram modicações a esta documentação, a versão atualizada estará disponível no site
da ASRock sem aviso prévio. Se precisar de assistência técnica relacionada a esta placa
principal, visite o nosso site para obter informações especícas sobre o modelo que estiver
utilizando. Você também poderá encontrar a lista de placas VGA e CPU mais recentes
suportadas no site da ASRock. Site da ASRock http://www.asrock.com.
83
Português
Fatal1ty B250M Performance Series
1.2 Especicações
Plataforma
•
Micro ATX Form Factor
CPU
•
Suporta Processadores 7
ª
e 6
ª
Geração Intel® Core
TM
i7/i5/i3/
Pentium®/Celeron® (Soquete 1151)
•
Digi Power design
•
Design com 6 fases de alimentação
•
Suporta a tecnologia Intel® Turbo Boost 2.0
Chipset
•
Intel® B250
Memória
•
Tecnologia de memória DDR4 de dois canais
•
4 x Slots DIMM DDR4
•
Suporta memória DDR4 2400/2133, não ECC, sem memória
intermediária*
* 7
ª
Ger Intel® CPU suporta DDR4 2400 originalmente; 6
ª
Ger Intel®
CPU suporta DDR4 2133 por overclocking.
•
Suporta módulos de memória ECC UDIMM (opera em modo
não-ECC)
•
Capacidade máxima da memória do sistema: 64GB
•
Suporta Extreme Memory Prole (XMP) 2.0 da Intel®
•
Contato em Ouro 15μ nos slots DIMM
Slotde
expansão
•
2 x Slots PCI Express 3.0 x16 (PCIE1:modo x16; PCIE4:modo
x4)*
* Suporta NVMe SSD nos discos de inicialização
•
2 x Slots PCI Express 3.0 x1 (Flexible PCIe)
•
Suporta AMD Quad CrossFireX
TM
e CrossFireX
TM
•
Contato em Ouro 15μ no Slot PCIe VGA (PCIE1)
84
Português
Grácos
•
Os grácos incorporados Intel® HD e as saídas VGA só podem ser
suportados com processadores com GPU integrada.
•
Suporta grácos incorporados Intel® HD: Intel® Quick Sync Video
com AVC, MVC (S3D) e MPEG-2 Full HW Encode1, Intel®
InTru
TM
3D, Tecnologia Intel® Clear Video HD, Intel® Insider
TM
,
Grácos Intel® HD
•
Gen9 LP, DX11.3, DX12
•
HWAEncode/Decode: VP8, HEVC 8b, VP9, HEVC 10b (Para 7
ª
Ger Intel® CPU)
•
Codicador/decodicador HWA: VP8 , HEVC 8b; Codicador/
decodicador GPU/SW: VP9, HEVC 10b (Para 6
ª
Ger Intel® CPU)
•
Memória compartilhada máxima de 1.024MB
* O tamanho da memória compartilhada máxima pode variar de
diferentes sistemas operacionais.
•
Três opções de saída de grácos: D-Sub, DVI-D e HDMI
•
Suporta conguração com três monitores
•
Suporta HDMI com resolução máx. até 4K x 2K (4096x2160) @
24Hz / (3840x2160) @ 30Hz
•
Suporta DVI-D com resolução máxima de até 1920x1200 @ 60Hz
•
Suporta D-Sub com resolução máxima de até 1920x1200 @ 60Hz
•
Suporta Auto sincronização labial, Deep Color (12bpc), xvYCC e
HBR (High Bit Rate Audio) com porta HDMI (É necessário um
monitor compatível com HDMI)
•
Suporta HDCP com Portas DVI-D e HDMI
•
Suporta reprodução Full HD 1080p Blu-ray (BD) com Portas
DVI-D e HDMI
Áudio
•
Áudio HD de 7.1 canais com proteção de conteúdo (Codec de
áudio Realtek ALC892)
*Para congurar Áudio 7.1 CH HD, é necessário usar um módulo de
áudio de painel frontal HD e habilitar o recurso de áudio multi-canal
pelo driver de áudio.
•
Suporte áudio Blu-ray superior
•
Suporta proteção contra sobretensão (Proteção Total Contra Picos
ASRock)
•
Capacitor de Áudio Série Ouro Fino Nichicon
•
Suporta Creative SoundBlaster Cinema3
85
Português
Fatal1ty B250M Performance Series
LAN
•
LAN Gigabit a 10/100/1000 Mb/s
•
Giga PHY Intel® I219V
•
Suporta Wake-On-LAN
•
Suporta Proteção contra Relâmpago/ESD (Proteção Total Contra
Picos ASRock)
•
Suporta Energy Ecient Ethernet 802.3az
•
Suporta PXE
E/S do
painel
posterior
•
1 x Porta PS/2 para mouse
•
1 x Porta PS/2 para Teclado
•
1 x Porta D-Sub
•
1 x Porta DVI-D
•
1 x Porta HDMI
•
1 x Porta USB 2.0 (Suporta Proteção ESD (Proteção Total Contra
Picos ASRock))
•
1 x Porta de Mouse Fatal1ty (USB 2.0) (Suporta Proteção ESD
(Proteção Total Contra Picos ASRock))
•
3 x Portas USB 3.0 Tipo A (Suporta Proteção ESD (Proteção Total
Contra Picos ASRock))
•
1 x Porta USB 3.0 Tipo C (Suporta Proteção ESD (Proteção Total
Contra Picos ASRock))
•
1 x Porta LAN RJ-45 com LED (LED ACT/LINK e LED DE
VELOCIDADE)
•
Fichas de áudio HD: Entrada de Linha / Autofalante Frontal /
Microfone
Armazena-
mento
•
6 x Conectores SATA3 6,0 Gb/s, suporte NCQ, AHCI e Conexão
a Quente*
* Se M2_1 é ocupado por um dispositivo tipo M2 SATA, SATA3_0
será desativado.
•
1 x Soquete Ultra M.2 (M2_1), suporta módulo M.2 SATA3 6,0
Gb/s tipo 2230/2242/2260/2280 e módulo M.2 PCI Express até
Gen3 x4 (32 Gb/s)**
•
1 x Soquete Ultra M.2 (M2_2), suporta módulo tipo
2230/2242/2260/2280 M.2 PCI Express até Gen3 x4 (32 Gb/s)**
** Se o slot PCIE2 ou slot PCIE3 estiver ocupado, o dispositivo tipo
PCIe M.2 no soquete M2_1 operará em Gen3 x2 (16 Gb/s).
** Suporta a tecnologia Intel® Optane
TM
(M2_2)
** Suporta NVMe SSD como discos de inicialização
** Suporta Kit ASRock U.2
86
Português
Conector
•
1 x Suporte Porta Impressão
•
1 x Suporte porta COM
•
1 x Plataforma TPM
•
1 x Intrusão do Chassi e Cabeçote de Autofalante
•
2 x Conectores ventilador CPU (1 x 4 pinos, 1 x 3 pinos)
* O Conector do Ventilador de CPU suporta o ventilador de CPU de
alimentação máxima 1A do ventilador (12W).
•
2 x Conectores de Ventoinha de Chassi (4 pinos) (Controle de
Velocidade de Ventoinha Inteligente)
* CHA_FAN1 e CHA_FAN2 podem detectar automaticamente se
ventoinha de 3 pinos ou 4 pinos está em uso.
•
1 x Conector alimentação ATX 24 pinos
•
1 x Conector de energia 8-pinos 12V
•
1 x Conector de áudio do painel frontal
•
2 x Plataformas USB 2.0 (Suporta 4 portas USB 2.0) (Suporta
Proteção ESD (Proteção Total Contra Picos ASRock))
•
1 x Plataformas USB 3.0 (Suporta 2 portas USB 3.0) (Suporta
Proteção ESD (Proteção Total Contra Picos ASRock))
Funções da
BIOS
•
AMI Legal UEFI BIOS com suporte multilingue GUI
•
ACPI 6.0 compatível com eventos de despertar
•
Suporte SMBIOS 2.7
•
CPU, GT_CPU, DRAM, PCH 1.0V, VCCIO, VCCSA, VCCST
Multi ajuste de tensão
Monitor de
hardware
•
Sensor de temperatura da CPU/Gabinete
•
Tacômetro da Ventoinha da CPU/Gabinete
•
Ventoinha silenciosa da CPU/Gabinete (Auto ajusta velocidade da
ventoinha do gabinete pela temperatura da CPU)
•
Controle de multi velocidade da Ventoinha da CPU/Gabinete
•
Detecção de ABERTURA da CAIXA
•
Monitoramento da tensão: +12V, +5V, +3.3V, CPU Vcore, DRAM,
PCH 1.0V
SO
•
Microso® Windows® 10 64-bit (Para 7
a
Ger Intel® CPU)
•
Microso® Windows® 10 64-bit / 8.1 64-bit / 7 32-bit / 7 64-bit
(Para 6
a
Ger Intel® CPU)
*Para instalar o SO Windows 7, um disco de instalação modicado
com condutores xHCI no arquivo ISO é necessário. Favor consultar a
página 153 para mais instruções detalhadas.
* Para o driver atualizado do Windows® 10, por favor, visite o website
da ASRock para mais detalhes: http://www.asrock.com
87
Português
Fatal1ty B250M Performance Series
* Para obter informações detalhadas sobre o produto, por favor, visite o nosso site: http://www.asrock.com
Por favor, observe que existe um certo risco envolvendo overclocking, incluindo o ajuste
das denições na BIOS, a aplicação de tecnologia Untied Overclocking ou a utilização
de ferramentas de overclocking de terceiros. O overclocking poderá afetar a estabilidade
do sistema ou mesmo causar danos nos componentes e dispositivos do seu sistema. Ele
deve ser realizado por sua conta e risco. Não nos responsabilizamos por possíveis danos
causados pelo overclocking.
Certicações
•
FCC, CE, WHQL, RCM, BSMI
•
Preparada para ErP/EuP (é necessária uma fonte de alimentação
preparada para ErP/EuP)
88
Português
1.3 Suportes e conectores onboard
Suporte do painel de
sistema
(PAINEL1 de 9 pinos)
(ver p.1, N.º 19)
Ligue o botão de
alimentação, o botão
de reinicialização e o
indicador do estado do
sistema no chassi deste
suporte, de acordo com a
descrição abaixo. Observe
os pinos positivos e
negativos antes de conectar
os cabos.
PWRBTN (Botão de alimentação):
Conecte o botão de alimentação no painel frontal do chassi. Você pode congurar a
forma para desligar o seu sistema através do botão de alimentação.
RESET (Botão de reinicialização):
Conecte o botão de reinicialização no painel frontal do chassi. Pressione o botão de
reinicialização para reiniciar o computador, se ele congela e falha ao realizar um reinício
normal.
PLED (LED de alimentação do sistema):
Conecte o indicador do estado da alimentação no painel frontal do chassi. O LED cará
aceso quando o sistema estiver em funcionamento. O LED cará piscando quando o
sistema estiver nos estados de suspensão S1/S3. O LED cará desligado quando o sistema
estiver no estado de suspensão S4 ou desligado (S5).
HDLED (LED de atividade do disco rígido):
Conecte o LED de atividade do disco rígido no painel frontal do chassi. O LED cará
aceso quando o disco rígido estiver lendo ou registrando dados.
O design do painel frontal poderá variar dependendo do chassi. Um módulo de painel
frontal consiste principalmente em um botão de alimentação, um botão de reinicializa-
ção, um LED de alimentação, um LED de atividade do disco rígido, um alto-falante, etc.
Ao conectar seu módulo de painel frontal do chassi a este conector, certique-se de que os
os e os pinos correspondem de forma correta.
Os conectores e suportes onboard NÃO são jumpers. NÃO coloque tampas de jumpers
sobre estes terminais e conectores Colocar tampas de jumpers sobre os terminais e conec-
tores irá causar danos permanentes à placa-mãe.
GND
R ESET#
P WRBTN#
P LED-
P LED+
GND
H DLED-
H DLED+
1
GND
89
Português
Fatal1ty B250M Performance Series
Intrusão do Chassi e
Cabeçote de Autofalante
(SPK_CI1 de 7 pinos)
(ver p.1, N.º 18)
Conecte a instrusão do
chassi e autofalante do
chassi a este cabeçote.
Conectores série ATA3
(SATA3_0:
ver p.1, N.º 10)
(SATA3_1:
ver p.1, N.º 11)
(SATA3_2:
ver p.1, N.º 13)
(SATA3_3:
ver p.1, N.º 14)
(SATA3_4:
ver p.1, N.º 16)
(SATA3_5:
ver p.1, N.º 15)
Estes seis conectores
SATA3 suportam
cabos de dados SATA
para dispositivos de
armazenamento interno
com uma taxa de
transferência de dados de
até 6,0 Gb/s.
Se M2_1 é ocupado por
um dispositivo tipo M.2
SATA, SATA3_0 será
desativado.
Suportes USB 2.0
(USB3_4 de 9-pinos)
(ver p.1, N.º 21)
(USB5_6 9-pinos)
(ver p.1, N.º 20)
Há dois cabeçotes nesta
placa-mãe. Cada suporte
USB 2.0 pode suportar
duas portas.
Suporte USB 3.0
(USB3_5_6 de 19 pinos)
(ver p.1, N.º 9)
Existe uma plataforma
nesta placa-mãe. Cada
suporte USB 3.0 pode
suportar duas portas.
1
IntA_ PB_D +
Dummy
IntA_ PB_D -
GND
IntA_ PB_S ST X +
GND
IntA_ PB_S ST X -
IntA_ PB_S SR X +
IntA_ PB_S SR X -
VbusVbus
Vbus
IntA_ PA_S SR X -
IntA_ PA_S SR X +
GND
IntA_ PA_S ST X -
IntA_ PA_S ST X +
GND
IntA_ PA_D -
IntA_ PA_D +
1
+5V
DUMMY
SIGNAL
GND
DUMMY
SPEAKER
DUMMY
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
USB_PWR
1
SATA3_4
SATA3_5
SATA3_2
SATA3_3
SATA3_1
SATA3_0
90
Português
GND
FAN_VOLTAGE_ CONTROL
FAN_SPEE D
FAN_SPEE D_CONTROL
GND
FA N_VOLTAGE
FA N_SPEED
Suporte de áudio do painel
frontal
(HD_AUDIO1 de 9 pinos)
(ver p.1, N.º 25)
Este suporte destina-se à
conexão dos dispositivos
de áudio no painel de
áudio frontal.
Conectores da Ventoinha
do Chassi
(CHA_FAN1 de 4 pinos)
(ver p.1, N.º 2)
(CHA_FAN2 de 4 pinos)
(ver p.1, N.º 12)
Ligue o cabo do ventilador
aos conectores do
ventilador e corresponda o
cabo preto com o pino de
ligação à terra.
Conectores do ventilador
da CPU
(CPU_FAN1 de 4 pinos)
(ver p.1, N.º 3)
(CPU_FAN2 de 3 pinos)
(ver p.1, N.º 4)
Esta placa mãe inclui um
conector de ventilador
da CPU (Ventilador
silencioso) de 4 pinos. Se
você pretende conectar um
ventilador da CPU de 3
pinos, por favor, conecte-o
ao Pino 1-3.
1. O Áudio de alta denição suporta Sensor de Adaptador, mas o o do painel no chassi
deverá suportar HDA para funcionar corretamente. Por favor, siga as instruções no
nosso manual e no manual do chassi para instalar o seu sistema.
2. Se utilizar um painel de áudio AC’97, instale-o no terminal de áudio do painel frontal
de acordo com os passos abaixo:
A. Ligue Mic_IN (MIC) a MIC2_L.
B. Conecte o Audio_R (RIN) a OUT2_R e Audio_L (LIN) a OUT2_L.
C. Conecte a ligação Terra (GND) à Terra (GND).
D. MIC_RET e OUT_RET destinam-se apenas ao painel de áudio HD. Você não
precisa ligá-los ao painel de áudio AC’97.
E. Para ativar o microfone frontal, vá à guia “Microfone Frontal” no painel de controle
Realtek e ajuste o “Volume de gravação”.
J _SENSE
O UT2_L
1
M IC_RET
P RESENCE#
GN D
O UT2_R
M IC2_R
M IC2_L
OUT_RET
GND
FAN_VOLTAGE_CO NTROL
FAN_SPEED
FAN_SPEED _CONTROL
FAN_VOLTAGE
GND
FAN_SPEED
FAN_SPEED_CONTROL
1
2
3
4
91
Português
Fatal1ty B250M Performance Series
Conector de alimentação
ATX
(ATXPWR1 de 24 pinos)
(ver p.1, N.º 8)
Esta placa-mãe inclui um
conector de alimentação
ATX de 24 pinos. Para
utilizar uma fonte de
alimentação ATX de 20
pinos, introduza-a no Pino
1 e Pino 13.
Conector de alimentação
de 12V ATX
(ATX12V1 de 8 pinos)
(ver p.1, N.º 1)
Esta placa-mãe inclui um
conector de alimentação
de 12V ATX de 8 pinos.
Para utilizar uma fonte
de alimentação ATX de 4
pinos, introduza-a no Pino
1 e Pino 5.
Suporte da porta serial
(COM1 de 9 pinos)
(ver p.1, N.º 24)
Este suporte COM1 recebe
um módulo da porta serial.
Suporte TPM
(TPMS1 de 17 pinos)
(ver p.1, N.º 22)
Este conector suporta um sistema
com Módulo de Plataforma Con-
ável (TPM), que pode armazenar
com segurança chaves, certica-
dos digitais, senhas e dados. Um
sistema TPM também ajuda a
melhorar a segurança de rede, a
proteger identidades digitais e a
garantir a integridade da plata-
forma.
Suporte Porta Impressão
(LPT1 de 25 pinos)
(ver p.1, N.º 23)
Esta é uma interface para o
cabo da porta de impressão
que permite uma
conexão conveniente dos
dispositivos da impressora.
1
GN D
SM B _DATA_MAIN
LA D 2
LA D 1
GN D
S_ P WRDWN #
SE R IRQ #
GN
D
P C I C L K
P C I R ST #
LA D 3
+3 V
LA D 0
+3VS B
GN D
FR A M E
SM B _CLK_MAIN
12
1
24
13
5
1
8
4
1
AF D #
ER R OR#
PI N IT#
GN D
SL I N#
ST B #
SP D 0
SP D 1
SP D 2
SP D 3
SP D 4
SP D 5
SP D 6
SP D 7
AC K #
BU S Y
PE
SL C T
92
Português
Cabeçote de LED RGB
AURA
(RGB_HEADER1 de 4
pinos)
(ver p.1, N.º 7)
Cabeçote RGB é usado
para conectar o cabo de
extensão de LED RGB
que permite aos usuários
escolher entre vários
efeitos de iluminação LED.
93
Türkçe
Fatal1ty B250M Performance Series
1 Giriş
ASRock'ın zorlu kalite kontrol süreçlerinden geçmiş olan ASRock Fatal1ty B250M
Performance Series anakartını satın aldığınız için teşekkür ederiz. Sağlam tasarımı ile
ASRock'ın kalite ve dayanıklılık taahhüdüne uygun şekilde mükemmel performans
sağlar.
1.1 Ambalaj İçeriği
•
ASRock Fatal1ty B250M Performance Series Anakartı (Micro ATX Form Faktörü)
•
ASRock Fatal1ty B250M Performance Series Hızlı Kurulum Kılavuzu
•
ASRock Fatal1ty B250M Performance Series Destek CD'si
•
2 x Seri ATA (SATA) Veri Kablosu (İsteğe Bağlı)
•
2 x M.2 Yuvası için vida (İsteğe Bağlı)
•
1 x I/O Panel Kalkanı
Anakart özellikleri ve BIOS yazılımı güncellenebileceğinden, bu dokümantasyonun
içeriği herhangi bir bildirimde bulunulmaksızın değiştirilebilir. Bu dokümantasyon
üzerinde herhangi bir değişiklik yapılması halinde, güncellenmiş sürüm, herhangi bir
bildirim yapılmaksızın ASRock'ın web sitesinde yer alacaktır.. Bu anakart ile ilgili olarak
teknik destek almak istiyorsanız, lütfen kullandığınız model hakkında özel bilgiler için
web sitemizi ziyaret edin. En güncel VGA kartları ve CPU destek listelerini de ASRock'ın
web sitesinden bulabilirsiniz. ASRock web sitesi http://www.asrock.com.
94
Türkçe
1.2 Özellikler
Platform
•
Micro ATX Form Faktörü
CPU
•
7. ve 6. Nesil Intel® Core
TM
i7/i5/i3/Pentium®/Celeron®
İşlemcileri destekler (Yuva 1151)
•
Digi Power design
•
6 Güç Saası tasarımı
•
Intel® Turbo Boost 2.0 Teknolojisini destekler
Yonga kümesi
•
Intel® B250
Bellek
•
Çi Kanallı DDR4 Bellek Teknolojisi
•
4 x DDR4 DIMM Yuvası
•
DDR4 2400/2133 ECC olmayan, arabelleksiz bellek destekler*
* 7. Nesil Intel® işlemci 2400'e kadar DDR4 destekler; 6. Nesil
Intel® işlemci 2133'e kadar DDR4 destekler.
•
ECC UDIMM bellek modüllerini destekler (ECC dışı modda
çalışır)
•
Maksimum sistem belleği kapasitesi: 64GB
•
Intel® Üstün Bellek Proli (XMP) 2.0 destekler
•
DIMM Yuvalarında 15μ Altın Temas
Genişletme
Yuvası
•
2 x PCI Express 3.0 x16 Yuva (PCIE1:x16 modu; PCIE4:x4
modu)*
* Önyükleme diskleri olarak NVMe SSD destekler
•
2 x PCI Express 3.0 x1 yuva (Flexible PCIe)
•
AMD Quad CrossFireX
TM
ve CrossFireX
TM
desteğine sahiptir
•
VGA PCIe Yuvasında (PCIE1) 15μ Altın Temas
95
Türkçe
Fatal1ty B250M Performance Series
Grakler
•
Intel® HD Graphics Dahili Görselleri ile VGA çıktıları,
yalnızca GPU entegre edilmiş işlemciler ile desteklenir.
•
Intel® HD Graphics Dahili Görsellerini destekler: AVC, MVC
(S3D) ve MPEG-2 Full HW Encode1, Intel® InTru
TM
3D,
Intel® Net Video HD Teknolojisi, Intel® Insider
TM
, Intel® HD
Graphics ile Intel® Quick Sync Video
•
Gen9 LP, DX11.3, DX12
•
HWA Kodlama/Kod Çözme: VP8, HEVC 8b, VP9, HEVC 10b
(7. Nesil Intel® işlemci için)
•
HWA Kodlama/Kod Çözme: VP8 , HEVC 8b; GPU/SW
Kodlama/Kod Çözme: VP9, HEVC 10b (6. Nesil Intel® işlemci
için)
•
Maksimum paylaşılan bellek 1.024MB
* En fazla paylaşılan bellek boyutu işletim sistemlerine göre
değişiklik gösterebilir.
•
Üç grak çıkışı seçeneği: D-sub, DVI-D ve HDMI
•
Üçlü Monitör Desteği
•
4K x 2K (4096x2160) @ 24Hz / (3840x2160) @ 30Hz
değerlerine kadar en fazla çözünürlükle HDMI destekler
•
1920x1200 @ 60Hz'ye kadar DVI-D işlevini destekler
•
1920x1200 @ 60Hz'ye kadar çözünürlükle D-Sub işlevini
destekler
•
HDMI Bağlantı Noktasıyla Otomatik Dudak Senkronizasyonu,
Derin Renk (12bpc), xvYCC ve HBR (Yüksek Bit Oranlı
Ses) özelliklerini destekler (Uyumlu bir HDMI monitörü
kullanılmalıdır)
•
DVI-D ve HDMI Bağlantı Noktalarıyla HDCP destekler
•
DVI-D ve HDMI Bağlantı Noktalarıyla Tam HD 1080p Blu-
ray (BD) kayıttan yürütme destekler
Ses
•
İçerik Koruma Özelliği ile 7.1 CH HD Ses (Realtek ALC892
Ses Codec Bileşeni)
*7.1 CH HD Ses kongürasyonu için bir HD ön panel ses
modülü kullanılmalı ve çok kanallı ses özelliği ses sürücüsüsü ile
etkinleştirilmelidir.
•
Üstün Blu-ray Ses desteği
•
Dalgalanma Koruması Destekler (ASRock Tam Ani Gerilim
Koruması)
•
Nichicon Fine Gold Serisi Ses Kapakları
•
Creative SoundBlaster Cinema3’ü destekler
96
Türkçe
LAN
•
Gigabit LAN 10/100/1000 Mb/s
•
Giga PHY Intel® I219V
•
Yerel Ağ Üzerinden Açmayı destekler
•
Yıldırım/ESD Koruması destekler (ASRock Tam Ani Gerilim
Koruması)
•
Enerji Verimliliğine Sahip Ethernet 802.3az işlevini destekler
•
PXE özelliğini destekler
Arka Panel I/O
•
1 x PS/2 Fare Bağlantı Noktası
•
1 x PS/2 Klavye Bağlantı Noktası
•
1 x D-Sub Bağlantı Noktası
•
1 x DVI-D Bağlantı Noktası
•
1 x HDMI Bağlantı Noktası
•
1 x Bağlayıcısı USB 2.0 Bağlantı Noktası (ESD Koruması
Destekler (ASRock Tam Ani Gerilim Koruması))
•
1 x Fatal1ty Fare Bağlantı Noktası (USB 2.0) (ESD Koruması
Destekler (ASRock Tam Ani Gerilim Koruması))
•
3 x tane USB 3.0 Tip A Bağlantı Noktası (ESD Koruması
Destekler (ASRock Tam Ani Gerilim Koruması))
•
1 x tane USB 3.0 Tip C Bağlantı Noktası (ESD Koruması
Destekler (ASRock Tam Ani Gerilim Koruması))
•
LED'e sahip 1 x RJ-45 LAN Bağlantı Noktası (ACT/LINK
LED ve SPEED LED)
•
HD Ses Jakları: Hat Girişi / Ön Hoparlör / Mikrofon
Depolama
•
6 x tane SATA3 6,0 Gb/sn. Bağlayıcı, NCQ, AHCI ve Tak
Çıkar* destekler*
* M2_1 bir SATA tipi M.2 aygıtı tarafından kullanılıyorsa,
SATA3_0 devre dışı bırakılacaktır.
•
1 x tane Ultra M.2 Yuvası(M2_1), 2230/2242/2260/2280 M.2
SATA3 6,0 Gb/sn. modülünü ve Gen3 x4 (32 Gb/sn.) değerine
kadar M.2 PCI Express modülünü destekler**
•
1 x Ultra M.2 Yuva (M2_2), Gen3 x4 (32 Gb/sn.) değerine
kadar tip 2230/2242/2260/2280 M.2 PCI Express modülü
destekler**
** PCIE2 veya PCIE3 yuvası doluysa, M2_1 yuvasındaki PCIe tipi
M.2 aygıtı Gen3 x2 (16 Gb/sn.) hızında çalışacaktır.
** Intel® Optane
TM
Teknolojisini destekler (M2_2)
** Önyükleme diskleri olarak NVMe SSD destekler
** ASRock U.2 Takımını destekler
97
Türkçe
Fatal1ty B250M Performance Series
Bağlayıcı
•
1 x Yazdırma Bağlantı Noktası Bağlantısı
•
1 x tane COM Bağlantı Noktası Bağlantısı
•
1 x tane TPM Bağlantısı
•
1 x Kasa Yetkisiz Erişim ve Hoparlör Bağlantısı
•
2 x İşlemci Fan Bağlayıcıları (1 x 4 pimli, 1 x 3 pimli)
* İşlemci Fan Bağlayıcı, en fazla 1 A (12 W) fan gücünde işlemci
fanı destekler.
•
2 x Kasa Fanı Bağlayıcısı (4 pimli) (Akıllı Fan Hızı Kontrolü)
* CHA_FAN1 ve CHA_FAN2, 3 pimli fanın mı yoksa 4 pimli
fanın mı kullanımda olduğunu otomatik olarak algılayabilir.
•
1 x tane 24 pim ATX Güç Bağlayıcısı
•
1 x 8 pim 12V Güç Bağlayıcısı
•
1 x tane Ön Panel Ses Bağlayıcısı
•
2 x tane USB 2.0 Bağlantısı (4 USB 2.0 bağlantı noktası
destekler) (ESD Koruması destekler (ASRock Tam Ani
Gerilim Koruması))
•
1 x tane USB 3.0 Bağlantısı (2 USB 3.0 bağlantı noktası
destekler) (ESD Koruması destekler (ASRock Tam Ani
Gerilim Koruması))
BIOS Özelliği
•
Çok dilli GUI desteği ile AMI UEFI Legal BIOS
•
ACPI 6.0 Uyumlu uyandırma olayları
•
SMBIOS 2.7 Desteği
•
CPU, GT_CPU, DRAM, PCH 1.0V, VCCIO, VCCSA, VCCST
Gerilimi Çoklu Ayarlama
Donanım
Monitörü
•
CPU/Kasa sıcaklığı tespiti
•
CPU/Kasa Fanı Devirölçer
•
CPU/Kasa Sessiz Fan (İşlemci sıcaklığıyla otomatik ayarlı kasa
fanı hızı)
•
CPU/Kasa Fanı çoklu hız kontrolü
•
KASA AÇIK algılaması
•
Voltaj izleme: +12V, +5V, +3,3V, İşlemci Vcore, DRAM,
PCH 1,0V
OS
•
Microso® Windows® 10 64 bit (7. Nesil Intel® işlemci için)
•
Microso® Windows® 10 64 bit / 8.1 64 bit / 7 32 bit / 7 64 bit
(6. Nesil Intel® işlemci için)
* Windows® 7 işletim sistemini yüklemek için, ISO dosyasında
sıkıştırılmış xHCI sürücülerine sahip değiştirilmiş yükleme
diski gereklidir. Daha ayrıntılı talimatlar için lütfen 153. sayfaya
başvurun.
* Güncellenmiş Windows® 10 sürücüsü konusunda ayrıntılar için
lütfen ASRock web sitesini ziyaret edin: http://www.asrock.com
98
Türkçe
Lütfen, BIOS ayarlarını düzenleme, Bağımsız Hız Aşırtma Teknolojinin uygulanması
ya da üçüncü kişilerin hız aşırtma araçlarının kullanılması da dahil olmak üzere tüm
hız aşırtma işlemlerinin belirli bir risk taşıdığını unutmayın. Hız aşırtma, sisteminizin
dayanıklılığını etkileyebilir, hatta sisteminizde yer alan bileşen ve aygıtlara zarar vere-
bilir. Bu, riski ve masraarı size ait olmak üzere gerçekleştirilmelidir. Hız aşırtmadan
doğabilecek zararlar konusunda sorumlu olmayacağız.
* Detaylı ürün bilgisi için, lütfen web sitemizi ziyaret edin: http://www.asrock.com
Belgeler
•
FCC, CE, WHQL, RCM, BSMI
•
ErP/EuP için hazır (ErP/EuP için hazır güç beslemesi
gereklidir)
99
Türkçe
Fatal1ty B250M Performance Series
1.3 Ekli Bağlantılar ve Bağlayıcılar
Sistem Paneli Bağlantısı
(9-pin PANEL1)
(bkz sf.1, No. 19)
Güç anahtarını bağlayın,
kasa üzerindeki anahtar ile
sistem durumu belirtecini
aşağıdaki pim düzenine
göre sıfırlayın. Kabloları
bağlarken pozitif ve negatif
pimleri not edin.
PWRBTN (Güç Anahtarı):
Güç anahtarını kasa ön paneline bağlayın. Güç anahtarını kullanarak sistemin hangi
yöne hareketle kapanacağını seçebilirsiniz.
RESET (Sıfırlama Anahtarı):
Sıfırlama anahtarını kasa ön paneline bağlayın. Bilgisayarın kilitlenmesi ve normal
şekilde yeniden başlatılamaması halinde reset (sıfırla) düğmesine basın.
PLED (Sistem Güç LED'i):
Güç durumu göstergesini kasa ön paneline bağlayın. Sistem çalışırken LED ışığı
yanacaktır. Sistem S1/S3 uyku durumdayken LED ışığı yanıp söner. Sistem S4 uyku
durumunda ya da kapalıyken (S5) LED ışık kapanır.
HDLED (Sabit Disk Etkinlik LED'i):
Sabit sürücü etkinlik LED'ini kasa ön paneline bağlayın. Sabit sürücü veri okur ya da
yazarken LED ışığı yanar.
Ön panel tasarımı kasaya göre değişiklik gösterebilir. Bir ön panel modülü, temel olarak
bir güç anahtarı, sıfırlama anahtarı, güç LED'i, sabit sürücü aktivitesi LED'i, hoparlör
gibi birimlerden oluşur. Kasanızın ön panel modülünü bu bağlantıya takmadan önce,
kablo düzenlemeleri ile pin düzenlemelerinin düzgün şekilde yapıldığından emin olun.
Ekli bağlantılar ve bağlayıcılar bağlantı teli değildir. Bağlantı teli kapaklarını bu
bağlantı ve bağlayıcılar üzerine yerleştirmeyin. Bağlantı teli kapaklarının bağlantılar ile
bağlayıcılar üzerine yerleştirilmesi, anakarta kalıcı hasar verebilir.
GND
R ESET#
P WRBTN#
P LED-
P LED+
GND
H DLED-
H DLED+
1
GND
100
Türkçe
Kasa Yetkisiz Erişim ve
Hoparlör Bağlantısı
(7-pin SPK_CI1)
(bkz. s.1, No. 18)
Lütfen kasa yetkisiz erişim
ve kasa hoparlörünü bu
bağlantıya takın.
Seri ATA3 Bağlayıcıları
(SATA3_0:
bkz. sf.1, No. 10)
(SATA3_1:
bkz. sf.1, No. 11)
(SATA3_2:
bkz. sf.1, No. 13)
(SATA3_3:
bkz. sf.1, No. 14)
(SATA3_4:
bkz. sf.1, No. 16)
(SATA3_5:
bkz. sf.1, No. 15)
Bu altı SATA3 bağlayıcısı,
veri aktarım hızı 6,0 Gb/
sn'ye kadar olan dahili
depolama aygıtları için
tasarlanmış SATA veri
kablolarını destekler.
M2_1 bir SATA tipi
M.2 aygıtı tarafından
kullanılıyorsa, SATA3_0
devre dışı bırakılacaktır.
USB 2.0 Bağlantıları
(9-pin USB3_4)
(bkz. s.1, No. 21)
(9 pimli USB5_6)
(bkz. s.1, No. 20)
Bu anakartta iki başlık
vardır. Her USB 2.0
bağlantısı, iki adet bağlantı
noktasını destekleyebilir.
USB 3.0 Bağlantı
(19-pin USB3_5_6)
(bkz. s.1, No. 9)
Bu anakartta bir başlık
vardır. Her USB 3.0
bağlantısı, iki adet bağlantı
noktasını destekleyebilir.
1
IntA_ PB_D +
Dummy
IntA_ PB_D -
GND
IntA_ PB_S ST X +
GND
IntA_ PB_S ST X -
IntA_ PB_S SR X +
IntA_ PB_S SR X -
VbusVbus
Vbus
IntA_ PA_S SR X -
IntA_ PA_S SR X +
GND
IntA_ PA_S ST X -
IntA_ PA_S ST X +
GND
IntA_ PA_D -
IntA_ PA_D +
1
+5V
DUMMY
SIGNAL
GND
DUMMY
SPEAKER
DUMMY
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
USB_PWR
1
SATA3_4
SATA3_5
SATA3_2
SATA3_3
SATA3_1
SATA3_0
101
Türkçe
Fatal1ty B250M Performance Series
Ön Panel Ses Bağlantısı
(9-pin HD_AUDIO1)
(bkz. s.1, No. 25)
Bu bağlantı, ses aygıtlarının
ön ses paneline bağlanması
içindir.
Kasa Fanı Bağlayıcıları
(4-pin CHA_FAN1)
(bkz sf.1, No. 2)
(4-pin CHA_FAN2)
(bkz sf.1, No. 12)
Lütfen fan kablosunu fan
konektörüne takın ve siyah
teli topraklama pinine
bağlayın.
CPU Fan Bağlayıcıları
(4-pin CPU_FAN1)
(bkz sf.1, No. 3)
(3-pin CPU_FAN2)
(bkz sf.1, No. 4)
Bu anakart, 4-Pin CPU
fan (Sessiz Fan) bağlayıcısı
sağlamaktadır. 3-Pin CPU
fan bağlamak istiyorsanız,
lütfen Pin 1-3'ü kullanın.
1. Yüksek Tanımlı Ses, Jak Algılama özelliğini destekler, ancak bu işlevin düzgün
çalışabilmesi için kasa üzerindeki panel kablosunun HDA işlevini desteklemesi
gerekmektedir. Sisteminizi kurarken, lütfen kılavuzumuzdaki talimatlar ile kasa
kılavuzundaki talimatları izleyin.
2. AC'97 ses paneli kullanıyorsanız, lütfen aşağıdaki adımları uygulayarak ön panel ses
bağlantısına takın:
A. Mic_IN'i (MIC) MIC2_L'ye bağlayın.
B. Audio_R'yi (RIN) OUT2_R'ye ve Audio_L'yi (LIN) OUT2_L'ye bağlayın.
C. Toprak'ı (GND) Toprak'a (GND) bağlayın.
D. MIC_RET ve OUT_RET yalnızca HD ses paneli içindir. AC'97 ses paneli için
bunları bağlamanıza gerek yoktur.
E. Ön mikrofonu etkinleştirmek için, Realtek Kontrol panelinde “FrontMic” sekmesine
gidin ve “Kayıt Ses Seviyesi”ni ayarlayın.
GND
FAN_VOLTAGE_ CONTROL
FAN_SPEE D
FAN_SPEE D_CONTROL
J _SENSE
O UT2_L
1
M IC_RET
P RESENCE#
GN D
O UT2_R
M IC2_R
M IC2_L
OUT_RET
GND
FAN_VOLTAGE_CO NTROL
FAN_SPEED
FAN_SPEED _CONTROL
FAN_VOLTAGE
GND
FAN_SPEED
FAN_SPEED_CONTROL
1
2
3
4
GND
FA N_VOLTAGE
FA N_SPEED
102
Türkçe
ATX Güç Bağlayıcısı
(24-pin ATXPWR1)
(bkz. s.1, No. 8)
Bu anakart, 24-pin
ATX güç bağlayıcısı
sağlamaktadır. 20-pin ATX
güç beslemesi kullanmak
için, lütfen Pin 1 ve Pin
13'e bağlayın.
ATX 12V Güç Bağlayıcısı
(8-pin ATX12V1)
(bkz. s.1, No. 1)
Bu anakart, 8-pin ATX
12V güç bağlayıcısı
sağlamaktadır. 4-pin ATX
güç beslemesi kullanmak
için, lütfen Pin 1 ve Pin 5'e
bağlayın.
Seri Bağlantı Noktası
Bağlantısı
(9-pin COM1)
(bkz. s.1, No. 24)
Bu COM1 bağlantısı seri
bağlantı yuvası modülünü
destekler.
TPM bağlantısı
(17-pin TPMS1)
(bkz. s.1, No. 22)
Bu bağlayıcı, anahtarlar, dijital
sertikalar, parolalar ve verileri
güvenli bir şekilde saklama özelliği
bulunan Güvenilir Platform
Modülü (TPM) sistemini destek-
ler. TPM sistemleri, aynı zamanda
ağ güvenliğinin artırılması, dijital
kimliklerin korunması ve platform
bütünlüğünün sağlanmasına da
yardımcıdır.
Yazdırma Bağlantı Noktası
Bağlantısı
(25-pin LPT1)
(bkz. s.1, No. 23)
Bu, yazıcı aygıtların
uyumlu bir şekilde
takılmasını sağlayan bir
yazdırma bağlantı noktası
arabirimidir.
1
GN D
SM B _DATA_MAIN
LA D 2
LA D 1
GN D
S_ P WRDWN #
SE R IRQ #
GN
D
P C I C L K
P C I R ST #
LA D 3
+3 V
LA D 0
+3VS B
GN D
FR A M E
SM B _CLK_MAIN
12
1
24
13
5
1
8
4
1
AF D #
ER R OR#
PI N IT#
GN D
SL I N#
ST B #
SP D 0
SP D 1
SP D 2
SP D 3
SP D 4
SP D 5
SP D 6
SP D 7
AC K #
BU S Y
PE
SL C T
103
Türkçe
Fatal1ty B250M Performance Series
AURA RGB LED
Bağlantısı
(4-pin RGB_HEADER1)
(bkz. s.1, No. 7)
AURA RGB bağlantısı,
kullanıcıların çeşitli LED
aydınlatma efektleri
arasında seçim yapmasına
izin veren RGB LED
uzatma kablosunu
bağlamak için kullanılır.
104
한 국 어
1 개요
ASRock Fatal1ty B250M Performance Series 마더보드를 구입해 주셔서 감사합니
다 . 이 마더보드는 ASRock 의 일관되고 엄격한 품질관리 하에 생산되어 신뢰성
이 우수합니다 . 품질과 내구성에 대한 ASRock 의 기준에 부합하는 우수한 성능
과 견고한 설계를 제공합니다 .
1.1 포장 내용물
• ASRock Fatal1ty B250M Performance Series 마더보드 (Micro ATX 폼 팩터 )
• ASRock Fatal1ty B250M Performance Series 간편 설치 안내서
• ASRock Fatal1ty B250M Performance Series 지원 CD
• 시리얼 ATA (SATA) 데이터 케이블 2 개 ( 선택 품목 )
• M.2 소켓용 나사 2 개 ( 선택 품목 )
• I/O 패널 실드 1 개
마더보드 규격과 BIOS 소프트웨어를 업데이트할 수도 있기 때문에 , 이 문서의
내용은 예고 없이 변경될 수 있습니다 . 이 설명서가 변경될 경우 , 업데이트된 버
전은 ASRock 의 웹사이트에서 추가 통지 없이 제공됩니다 . 이 마더보드와 관련
하여 기술적 지원이 필요한 경우 , 당사의 웹사이트를 방문하여 사용 중인 모델
에 대한 구체적 정보를 구하십시오 . ASRock 의 웹사이트에서는 최신 VGA 카드
와 CPU 지원 목록도 찾을 수 있습니다 . ASRock 웹사이트 http://www.asrock.com.
105
한 국 어
Fatal1ty B250M Performance Series
1.2 규격
플랫폼
• Micro ATX 폼 팩터
CPU
• 7 세대 및 6 세대 Intel® Core
TM
i7/i5/i3/Pentium®/Celeron® 프
로세서 ( 소켓 1151) 지원
•
Digi Power design
• 6 개 전원 위상 구조
• Intel® Turbo Boost 2.0 기술 지원
칩세트
• Intel® B250
메모리
• 듀얼 채널 DDR4 메모리 기술
• DDR4 DIMM 슬롯 4 개
• DDR4 2400/2133 비 -ECC, 비버퍼링 메모리 지원 *
* 7 세대 Intel® CPU 는 최대 2400 까지 DDR4 를 지원하고 , 6 세
대 Intel® CPU 는 2133 까지 DDR4 를 지원합니다 .
• ECC UDIMM 메모리 모듈 ( 비 ECC 모드에서 작동함 ) 지
원
• 시스템 메모리 최대 용량 : 64GB
• Intel® Extreme Memory Prole (XMP) 2.0 지원
• DIMM 슬롯에 15 μ Gold Contact 장착
확장슬롯
• PCI Express 3.0 x16 슬롯 2 개 (PCIE1:x16 모드 , PCIE4:x4 모
드 )*
* NVMe SSD 를 부팅 디스크로 사용 가능하도록 지원
• PCI Express 3.0 x1 슬롯 2 개 (Flexible PCIe)
• AMD Quad CrossFireX
TM
및 CrossFireX
TM
지원
• VGA PCIe 슬롯에 15 μ Gold Contact 장착 (PCIE1)
106
한 국 어
그래픽
• Intel® HD 그래픽스 빌트 - 인 비주얼과 VGA 출력은 GPU
통합 프로세서로만 지원할 수 있습니다 .
• Intel® HD 그래픽스 빌트 - 인 비주얼 지원 : AVC, MVC (S3D)
및 MPEG-2 풀 HW Encode1 지원 Intel® Quick Sync Video,
Intel® InTru
TM
3D, Intel® 클리어 비디오 HD 기술 , Intel®
Insider
TM
, Intel® HD 그래픽스
• Gen9 LP, DX11.3, DX12
• HWA 인코드 / 디코드 : VP8, HEVC 8b, VP9, HEVC 10b
(7 세대 Intel® CPU 의 경우 )
• HWA 인코드 / 디코드 : VP8 , HEVC 8b; GPU/SW 인코드 /
디코드 : VP9, HEVC 10b(6 세대 Intel® CPU 의 경우 )
• 최대 공유 메모리 1,024MB
* 최대 공유 메모리 크기는 운영 체제에 따라 다를 수 있습니
다 .
• 그래픽 출력 옵션 세 개 : D-Sub, DVI-D 및 HDMI
• 삼중 모니터 지원
• HDMI 지원 ( 최대 해상도 4K x 2K (4096x2160) @ 24Hz /
(3840x2160) @ 30Hz)
• DVI-D 지원 ( 최대 해상도 1920x1200 @ 60Hz)
• D-Sub 지원 ( 최대 해상도 1920x1200 @ 60Hz)
• Auto Lip Sync, Deep Color (12bpc), xvYCC 및 HBR (High Bit
Rate Audio)(HDMI 포트 포함 ) 지원 (HDMI 호환 모니터 필
요 )
• DVI-D 및 HDMI 포트를 이용한 HDCP 지원
• DVI-D 및 HDMI 포트를 이용한 Full HD 1080p Blu-ray (BD)
재생 지원
오디오
• 7.1 CH HD 오디오 콘텐츠 보호를 이용한 지원 (Realtek
ALC892 오디오 코덱 )
*7.1 CH HD 오디오를 구성하려면 HD 전면 패널 오디오 모듈
을 사용하고 다채널 오디오 기능을 오디오 드라이버로 활성화
해야 합니다 .
• 프리미엄 Blu-ray 오디오 지원
• 서지 보호 지원 (ASRock 풀 스파이크 보호 )
• Nichicon Fine Gold 시리즈 오디오 캡
• Creative SoundBlaster Cinema3 지원
107
한 국 어
Fatal1ty B250M Performance Series
LAN
• Gigabit LAN 10/100/1000 Mb/s
• Giga PHY Intel® I219V
• Wake-On-LAN 지원
• 번개 /ESD 보호 지원 (ASRock 풀 스파이크 보호 )
• 절전형 이더넷 802.3az 지원
• PXE 지원
후면 패널
I/O
• PS/2 마우스 포트 1 개
• PS/2 키보드 포트 1 개
• D-Sub 포트 1 개
• DVI-D 포트 1 개
• HDMI 포트 1 개
• USB 2.0 포트 1 개 (ESD 보호 지원 (ASRock 풀 스파이크
보호 ))
• Fatal1ty 마우스 포트 1 개 (USB 2.0) (ESD 보호 지원 (ASRock
풀 스파이크 보호 ))
• USB 3.0 타입 A 포트 3 개 (ESD 보호 지원 (ASRock 풀 스파
이크 보호 ))
• USB 3.0 타입 C 포트 1 개 (ESD 보호 지원 (ASRock 풀 스파
이크 보호 ))
• LED 장착 RJ-45 LAN 포트 1 개 (ACT/LINK LED 및 SPEED
LED)
• HD 오디오 잭 : 라인 입력 / 전면 스피커 / 마이크
저장 장치
• SATA3 6.0 Gb/s 커넥터 6 개가 NCQ, AHCI 및 핫 플러그 지
원 *
* SATA- 타입 M.2 장치에서 M2_1 을 사용 중이면 , SATA3_0 이
비활성화됩니다 .
• 울트라 M.2 소켓 (M2_1) 1개 , 타입 2230/2242/2260/2280 M.2
SATA3 6.0 Gb/s 모듈 및 Gen3 M.2 PCI Express 모듈을 4 개
(32 Gb/s) 까지 지원 **
• Ultra M.2 Socket (M2_2) 1 개 , 타입 2230/2242/2260/2280 최
대 Gen3 M.2 PCI Express 모듈 4 개 지원 (32 Gb/s)**
** PCIE2 슬롯 또는 PCIE3 슬롯이 사용 중인 경우 , M2_1 소켓
상의 PCIe 타입 M.2 장치가 Gen3 x2(16 Gb/s) 로 실행됩니다 .
** Intel® Optane
TM
기술 지원 (M2_2)
** NVMe SSD 를 부팅 디스크로 사용 가능하도록 지원
** ASRock U.2 키트 지원
108
한 국 어
커넥터
• 인쇄 포트 헤더 1 개
• COM 포트 헤더 1 개
• TPM 헤더 1 개
• 섀시 침입 및 스피커 헤더 1 개
• CPU 팬 커넥터 2 개 (4 핀 1 개 , 3 핀 1 개 )
* CPU 팬 커넥터는 팬 전력이 최대 1A(12W) 인 CPU 팬을 지원
합니다 .
• 섀시 팬 커넥터 (4 핀 ) 2 개 ( 스마트 팬 속도 제어 )
* 3 핀 또는 4 핀 팬이 사용 중인 경우 , CHA_FAN1 과 CHA_
FAN2 가 자동으로 감지할 수 있습니다 .
• 24 핀 ATX 전원 커넥터 1 개
• 8 핀 12V 전원 커넥터 1 개
• 전면 패널 오디오 커넥터 1 개
• USB 2.0 헤더 2 개 (USB 2.0 포트 4 개 지원 ) (ESD 보호 지원
(ASRock 풀 스파이크 보호 ))
• USB 3.0 헤더 1 개 (USB 3.0 포트 2 개 지원 ) (ESD 보호 지원
(ASRock 풀 스파이크 보호 ))
BIOS 기능
• 다국어 GUI 지원을 제공하는 AMI UEFI 적합형 BIOS
• ACPI 6.0 준수 웨이크 업 이벤트
• SMBIOS 2.7 지원
• CPU, GT_CPU, DRAM, PCH 1.0V, VCCIO, VCCSA, VCCST
전압 다중 조정
하드웨어
모니터
• CPU/ 섀시 온도 감지
• CPU/ 섀시 팬 타코미터
• CPU/ 섀시 저소음 팬 (CPU 온도에 의한 섀시 팬 속도 자동
조절 )
• CPU/ 섀시 팬 다중 속도 조절
• 케이스 열림 감지
• 전압 모니터링 : +12V, +5V, +3.3V, CPU Vcore, DRAM, PCH
1.0V
109
한 국 어
Fatal1ty B250M Performance Series
* 자세한 제품 정보에 대해서는 당사 웹사이트를 참조하십시오 : http://www.asrock.com
BIOS 설정을 조정하거나 Untied Overclocking Technology 를 적용하거나 타업체
의 오버클로킹 도구를 사용하는 것을 포함하는 오버클로킹에는 어느 정도의 위
험이 따른다는 것을 유념하십시오 . 오버클로킹은 시스템 안정성에 영향을 주거
나 심지어 시스템의 구성 요소와 장치에 손상을 입힐 수도 있습니다 . 오버클로
킹은 사용자 스스로 위험과 비용을 감수하고 해야 합니다 . 당사는 오버클로킹
에 의해 발생할 수 있는 손상에 대해서 책임이 없습니다 .
OS
• Microso® Windows® 10 64 비트 (7 세대 Intel® CPU 의 경우 )
• Microso® Windows® 10 64 비트 /8.1 64 비트 /7 32 비트 /7 64
비트 (6 세대 Intel® CPU 의 경우 )
* Windows® 7 OS 를 설치하려면 , xHCI 드라이버를 ISO 파일에
포함시킨 수정된 설치 디스크가 필요합니다 . 자세한 사용법
은 153 페이지를 참조하십시오 .
* 업데이트된 Windows® 10 드라이브의 자세한 내용은 다음의
ASRock 웹사이트를 참조하십시오 . http://www.asrock.com
인증
• FCC, CE, WHQL, RCM, BSMI
• ErP/EuP 사용 가능 (ErP/EuP 사용 가능 전원공급장치 필요 )
110
한 국 어
1.3 온보드 헤더 및 커넥터
시스템 패널 헤더
(9 핀 PANEL1)
(1 페이지 , 19 번 항목 참조 )
섀시의 전원 스위치 , 리
셋 스위치 , 시스템 상태
표시등을 아래의 핀 할당
에 따라 이 헤더에 연결
합니다 . 케이블을 연결
하기 전에 양극 핀과 음
극 핀을 기록합니다 .
PWRBTN( 전원 스위치 ):
섀시 전면 패널의 전원 스위치에 연결합니다 . 전원 스위치를 이용해 시스템을
끄는 방법을 구성할 수 있습니다 .
RESET( 리셋 스위치 ):
섀시 전면 패널의 리셋 스위치에 연결합니다 . 컴퓨터가 정지하고 정상적 재시
작을 수행하지 못할 경우 리셋 스위치를 눌러 컴퓨터를 재시작합니다 .
PLED( 시스템 전원 LED):
섀시 전면 패널의 전원 상태 표시등에 연결합니다 . 시스템이 작동하고 있을 때
는 LED 가 켜져 있습니다 . 시스템이 S1/S3 대기 상태에 있을 때는 LED 가 계속
깜박입니다 . 시스템이 S4 대기 상태 또는 전원 꺼짐 (S5) 상태에 있을 때는 LED
가 꺼져 있습니다 .
HDLED( 하드 드라이브 동작 LED):
섀시 전면 패널의 하드 드라이브 동작 LED 에 연결합니다 . 하드 드라이브가 데
이터를 읽거나 쓰고 있을 때 LED 가 켜져 있습니다 .
전면 패널 디자인은 섀시별로 다를 수 있습니다 . 전면 패널 모듈은 주로 전원 스
위치 , 리셋 스위치 , 전원 LED, 하드 드라이브 동작 LED, 스피커 등으로 구성되
어 있습니다 . 섀시 전면 패널 모듈을 이 헤더에 연결할 때 와이어 할당과 핀 할당
이 정확히 일치하는지 확인합니다 .
온보드 헤더와 커넥터는 점퍼가 아닙니다 . 점퍼 캡을 온보드 헤더와 커넥터에
씌우지 마십시오 . 점퍼 캡을 온보드 헤더와 커넥터에 씌우면 마더보드가 영구
적으로 손상됩니다 .
GND
R ESET#
P WRBTN#
P LED-
P LED+
GND
H DLED-
H DLED+
1
GND
111
한 국 어
Fatal1ty B250M Performance Series
섀시 침입 및 스피커 헤더
(7 핀 SPK_CI1)
(1 페이지 , 18 번 항목 참조 )
섀시 침입 및 섀시 스피
커를 이 헤더에 연결하십
시오 .
시리얼 ATA3 커넥터
(SATA3_0:
1 페이지 , 10 번 항목 참조 )
(SATA3_1:
1 페이지 , 11 번 항목 참조 )
(SATA3_2:
1 페이지 , 13 번 항목 참조 )
(SATA3_3:
1 페이지 , 14 번 항목 참조 )
(SATA3_4:
1 페이지 , 16 번 항목 참조 )
(SATA3_5:
1 페이지 , 15 번 항목 참조 )
이들 6 개의 SATA3 커넥
터는 최대 6.0 Gb/s 데이
터 전송 속도를 제공하는
내부 저장 장치용 SATA
데이터 케이블을 지원합
니다 .
SATA- 타입 M.2 장치에
서 M2_1 을 사용 중이면 ,
SATA3_0 이 비활성화됩
니다 .
USB 2.0 헤더
(9 핀 USB3_4)
(1 페이지 , 21 번 항목 참조 )
(9 핀 USB5_6)
(1 페이지 , 20 번 항목 참조 )
이 마더보드에는 헤더 두
개가 있습니다 . 각 USB
2.0 헤더는 포트 두 개를
지원할 수 있습니다 .
USB 3.0 헤더
(19 핀 USB3_5_6)
(1 페이지 , 9 번 항목 참조 )
이 마더보드에는 헤더 한
개가 있습니다 . 각 USB
3.0 헤더는 포트 두 개를
지원할 수 있습니다 .
1
IntA_ PB_D +
Dummy
IntA_ PB_D -
GND
IntA_ PB_S ST X +
GND
IntA_ PB_S ST X -
IntA_ PB_S SR X +
IntA_ PB_S SR X -
VbusVbus
Vbus
IntA_ PA_S SR X -
IntA_ PA_S SR X +
GND
IntA_ PA_S ST X -
IntA_ PA_S ST X +
GND
IntA_ PA_D -
IntA_ PA_D +
1
+5V
DUMMY
SIGNAL
GND
DUMMY
SPEAKER
DUMMY
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
USB_PWR
1
SATA3_4
SATA3_5
SATA3_2
SATA3_3
SATA3_1
SATA3_0
112
한 국 어
전면 패널 오디오 헤더
(9 핀 HD_AUDIO1)
(1 페이지 , 25 번 항목 참조 )
이 헤더는 오디오 장치를
전면 오디오 패널에 연결
하는 데 사용됩니다 .
섀시 팬 커넥터
(4 핀 CHA_FAN1)
(1 페이지 , 2 번 항목 참조 )
(4 핀 CHA_FAN2)
(1 페이지 , 12 번 항목 참조 )
팬 케이블을 팬 커넥터에
연결하고 검은색 와이어
를 접지핀에 연결하십시
오 .
CPU 팬 커넥터
(4 핀 CPU_FAN1)
(1 페이지 , 3 번 항목 참조 )
(3 핀 CPU_FAN2)
(1 페이지 , 4 번 항목 참조 )
이 마더보드에는 4 핀
CPU 팬 ( 저소음 팬 ) 커
넥터가 탑재되어 있습니
다 . 3 핀 CPU 팬을 연결
하려는 경우 핀 1-3 에 연
결하십시오 .
1.
고음질 오디오는 잭 감지를 지원하지만 올바르게 작동하려면 섀시의 패널 와
이어가 HDA 를 지원해야 합니다 . 설명서 및 섀시 설명서에 나와 있는 지침을
따라 시스템을 설치하십시오 .
2.
AC’97 오디오 패널을 사용할 경우 아래와 같은 절차를 따라 전면 패널 오디오
헤더에 설치하십시오 :
A. Mic_IN (MIC) 를 MIC2_L 에 연결합니다 .
B. Audio_R (RIN) 을 OUT2_R 에 연결하고 Audio_L (LIN) 을 OUT2_L 에 연결
합니다 .
C. 접지 (GND) 를 접지 (GND) 에 연결합니다 .
D. MIC_RET 및 OUT_RET 는 HD 오디오 패널에만 사용됩니다 . AC’97 오디오
패널용으로 연결할 필요가 없습니다 .
E. 전면 마이크를 활성화하려면 Realtek 제어판에서 “FrontMic” 탭으로 가서
“Recording Volume( 녹음 볼륨 )”을 조정합니다 .
GND
FAN_VOLTAGE_ CONTROL
FAN_SPEE D
FAN_SPEE D_CONTROL
J _SENSE
O UT2_L
1
M IC_RET
P RESENCE#
GN D
O UT2_R
M IC2_R
M IC2_L
OUT_RET
GND
FAN_VOLTAGE_CO NTROL
FAN_SPEED
FAN_SPEED _CONTROL
FAN_VOLTAGE
GND
FAN_SPEED
FAN_SPEED_CONTROL
1
2
3
4
GND
FA N_VOLTAGE
FA N_SPEED
113
한 국 어
Fatal1ty B250M Performance Series
ATX 전원 커넥터
(24 핀 ATXPWR1)
(1 페이지 , 8 번 항목 참조 )
이 마더보드에는 24 핀
ATX 전원 커넥터가 탑
재되어 있습니다 . 20 핀
ATX 전원공급장치를 사
용하려면 핀 1 과 핀 13 을
따라 연결하십시오 .
ATX 12V 전원 커넥터
(8 핀 ATX12V1)
(1 페이지 , 1 번 항목 참조 )
이 마더보드에는 8 핀
ATX 12V 전원 커넥터가
탑재되어 있습니다 . 4 핀
ATX 전원공급장치를 사
용하려면 핀 1 과 핀 5 을
따라 연결하십시오 .
시리얼 포트 헤더
(9 핀 COM1)
(1 페이지 , 24 번 항목 참조 )
이 COM1 헤더는 시리얼
포트 모듈을 지원합니다 .
TPM 헤더
(17 핀 TPMS1)
(1 페이지 , 22 번 항목 참조 )
이 커넥터는 키 , 디지털
인증서 , 암호 및 데이터를
안전하게 보관할 수 있는
TPM(Trusted Platform Module)
시스템을 지원합니다 .
TPM 시스템은 네트워크
보안을 강화하고 , 디지털
신원을 보호하며 플랫폼
무결성을 유지합니다 .
인쇄 포트 헤더
(25 핀 LPT1)
(1 페이지 , 23 번 항목 참조 )
프린터 장치의 간편한 연
결을 가능하게 하는 인쇄
포트 케이블용 인터페이
스입니다 .
1
GN D
SM B _DATA_MAIN
LA D 2
LA D 1
GN D
S_ P WRDWN #
SE R IRQ #
GN
D
P C I C L K
P C I R ST #
LA D 3
+3 V
LA D 0
+3VS B
GN D
FR A M E
SM B _CLK_MAIN
12
1
24
13
5
1
8
4
1
AF D #
ER R OR#
PI N IT#
GN D
SL I N#
ST B #
SP D 0
SP D 1
SP D 2
SP D 3
SP D 4
SP D 5
SP D 6
SP D 7
AC K #
BU S Y
PE
SL C T
114
한 국 어
AURA RGB LED 헤더
(4 핀 RGB_HEADER1)
(1 페이지 , 7 번 항목 참조 )
AURA RGB 헤더는 다양
한 LED 조명 효과를 선택
할 수 있는 RGB LED 연
장 케이블을 연결하는 데
사용됩니다 .
115
日本語
Fatal1ty B250M Performance Series
1 はじめに
ASRock
ASRock Fatal1ty B250M Performance Series
ASRock
1.1 パッケージの内容
• ASRock Fatal1ty B250M Performance Series ATX
• ASRock Fatal1ty B250M Performance Series
• ASRock Fatal1ty B250M Performance Series CD
• 2 x ATA SATA
• 2 x M.2
• 1 x I/O
BIOS
ASRock
ASRock VGA CPU
ASRock http://www.asrock.com.
116
日本語
1.2 仕様
プラット
フォーム
• ATX
CPU
• 7
6 I ntel® Core
TM
i7/i5/i3/Pentium®/
Celeron® 1151
•
Digi Power design
• 6
• Intel® 2.0
チップセット
• Intel® B250
メモリ
• D DR4
• 4 x DDR4 DIMM
• DDR4 2400/2133 ECC *
* 7 I ntel® CPU 2400 DDR4
6 I ntel® CPU 2133 DDR4
• ECC UDIMM non-ECC
• 64GB
• Intel® XMP 2.0
• DIMM 15
拡張スロット
• 2 x PCI Express 3.0 x16 PCIE1: 16 PCIE4:
4 *
* NVMe SSD
• 2 x PCI Express 3.0 x1 (Flexible PCIe)
• AMD Quad CrossFireX
TM
CrossFireX
TM
• VGA PCIe 15 PCIE1
117
日本語
Fatal1ty B250M Performance Series
グラフィッ
クス
• Intel®HD VGA
GPU
• Intel®HD AVC
MVC (S3D) MP EG-2 Full HW Encode1
Intel® Intel® InTru
TM
3D, Intel®
HD Intel® Insider
TM
, Intel® HD
• Gen9 LP DX11.3 DX12
• HWA / : VP8 HEVC 8b VP9 HEVC 10b
7 I ntel® CPU
• HWA / : VP8 HEVC 8b GPU/SW
/ : VP9 HEVC 10b 6 I ntel® CPU
• 1,024MB
*
• 3 : D-Sub DVI-D HDMI
• 3
• HDMI 4K x 2K (4096x2160) @ 24H z /
(3840x2160) @ 30Hz
• DVI-D 1920x1200 @60Hz
• D-Sub 1920x1200 @60Hz
• HDMI 12bpc
xvYCC HBR
HDMI
• DVI-D HDMI HDCP
• DVI-D HDMI Full HD 1080p Blu-ray (BD)
オーディオ
• 7.1 CH HD Realtek
ALC892
*7.1 CH HD HD
•
• ASRock
•
• Creative SoundBlaster Cinema3
118
日本語
LAN
• LAN 10/100/1000 Mb/s
• P HY Intel® I219V
• Wake-On-LAN
• / ESD ASRock
• 802.3az
• PXE
リアパネル
I/O
• 1 x PS/2
• 1 x PS/2
• 1 x D-Sub
• 1 x DVI-D
• 1 x HDMI
• 1 x USB 2.0 ESD ASRock
• 1 x Fatal1ty USB 2.0 ESD
ASRock
• 3 x USB 3.0 Type-A ESD
ASRock
• 1 x USB 3.0 Type-C ESD
ASRock
• LED 1 x RJ-45 LAN ACT/LINK LED SPEED
LED
• HD : / /
ストレージ
• 6 x SATA3 6.0 Gb/s NCQ AHCI
*
* SATA M.2 M2_1
SATA3_0
• 1 x M.2 (M2_1) 2230/2242/2260/2280
M.2 SATA3 6.0 Gb/s G en3 x4 (32 Gb/s)
M.2 PCI Express *
• 1 x M.2 (M2_2) G en3 x4 (32 Gb/s)
2230/2242/2260/2280 M.2 PCI E xpress
**
** PCIE2 PCIE3
M2_1 PCIe M.2 Gen3 x2
(16 Gb/s)
** Intel® Optane
TM
(M2_2)
** NVMe SSD
** ASRock U.2
119
日本語
Fatal1ty B250M Performance Series
コネクタ
• 1 x
• 1 x COM
• 1 x TPM
• 1 x
• 2 x CPU 1 x 4 1 x 3
* CPU 1A (12W ) CPU
• 2 x 4
* CPU_FAN1 CH A_FAN2 3 4
• 1 x 24 ATX
• 1 x 8 12V
• 1 x
• 2 x USB 2.0 4 USB 2.0
ESD ASRock
• 1 x USB 3.0 2 USB 3.0
ESD ASRock
BIOS 機能
• AMI UEFI Legal BIOS GUI
• ACPI 6.0
• SMBIOS 2.7
• CPU GT_CPU DRAM PCH 1.0V VCCIO VCCSA VCCST
ハードウェア
モニター
• CPU/
• CPU /
• CPU/ CPU
• CPU/
•
• : +12V +5V +3.3V CPU Vcore DRAM PCH 1.0V
OS
• Microso® Windows® 10 64-bit 7 I ntel® CPU
• Microso® Windows® 10 64-bit / 8.1 64-bit / 7 32-bit / 7 64-bit
6 I ntel® CPU
* Windows® 7 OS xHCI
ISO
153
* Windows® 10 ASRock
: http://www.asrock.com
120
日本語
* http://www.asrock.com
BIOS
認証
• FCC CE WHQL RCM BSMI
• ErP/EuP Ready ErP/EuP
121
日本語
Fatal1ty B250M Performance Series
1.3 オンボードのヘッダーとコネクター
9 1
p.1 No. 19
PWRBTN
RESET
PLED LED
LED S1/S3 LED
S4 S5
LED
HDLED LED
LED
LED
LED
LED
GND
R ESET#
P WRBTN#
P LED-
P LED+
GND
H DLED-
H DLED+
1
GND
122
日本語
7 SPK_CI1
p.1 No. 18
ATA3
(SATA3_0:
p.1 No. 10
(SATA3_1:
p.1 No. 11
(SATA3_2:
p.1 No. 13
(SATA3_3:
p.1 No. 14
(SATA3_4:
p.1 No. 16
(SATA3_5:
p.1 No. 15
6 SATA3
6.0 Gb/
SATA
SATA M.2
M2_1
SATA3_0
USB 2.0
9 USB3_4
p.1 No. 21
9 USB5_6
p.1 No. 20
2
USB 2.0
2
USB 3.0
19 USB3_5_6
p.1 No. 9
1
USB 3.0
2
1
IntA_ PB_D +
Dummy
IntA_ PB_D -
GND
IntA_ PB_S ST X +
GND
IntA_ PB_S ST X -
IntA_ PB_S SR X +
IntA_ PB_S SR X -
VbusVbus
Vbus
IntA_ PA_S SR X -
IntA_ PA_S SR X +
GND
IntA_ PA_S ST X -
IntA_ PA_S ST X +
GND
IntA_ PA_D -
IntA_ PA_D +
1
+5V
DUMMY
SIGNAL
GND
DUMMY
SPEAKER
DUMMY
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
USB_PWR
1
SATA3_4
SATA3_5
SATA3_2
SATA3_3
SATA3_1
SATA3_0
123
日本語
Fatal1ty B250M Performance Series
9 HD_AUDIO1
p.1 No. 25
4 CHA_FAN1
p.1 No. 2
4 CHA_FAN2
p.1 No. 12
CPU
4 CPU_FAN1
p.1 No. 3
3 CPU_FAN2
p.1 No. 4
4
CPU
3 CPU
1-3
1.
HDA
2.
AC97
A. Mic_IN (MIC) MIC2_L
B. Audio_R (RIN) OUT2_R Audio_L (LIN) OUT2_L
C. (GND) (GND)
D. MIC_RET OUT_RET HD AC97
E. Realtek FrontMic
GND
FAN_VOLTAGE_ CONTROL
FAN_SPEE D
FAN_SPEE D_CONTROL
J _SENSE
O UT2_L
1
M IC_RET
P RESENCE#
GN D
O UT2_R
M IC2_R
M IC2_L
OUT_RET
GND
FAN_VOLTAGE_CO NTROL
FAN_SPEED
FAN_SPEED _CONTROL
FAN_VOLTAGE
GND
FAN_SPEED
FAN_SPEED_CONTROL
1
2
3
4
GND
FA N_VOLTAGE
FA N_SPEED
124
日本語
ATX
24 ATXPWR1
p.1 No. 8
24
ATX
20 ATX
1 13
ATX 12V
8 ATX12V1
p.1 No. 1
8
ATX12V
4
ATX
1 5
9 COM1
p.1 No. 24
COM1
TPM
17 TPMS1
p.1 No. 22
TPM
TPM
25 LPT1
p.1 No. 23
1
GN D
SM B _DATA_MAIN
LA D 2
LA D 1
GN D
S_ P WRDWN #
SE R IRQ #
GN
D
P C I C L K
P C I R ST #
LA D 3
+3 V
LA D 0
+3VS B
GN D
FR A M E
SM B _CLK_MAIN
12
1
24
13
5
1
8
4
1
AF D #
ER R OR#
PI N IT#
GN D
SL I N#
ST B #
SP D 0
SP D 1
SP D 2
SP D 3
SP D 4
SP D 5
SP D 6
SP D 7
AC K #
BU S Y
PE
SL C T
125
日本語
Fatal1ty B250M Performance Series
AURA RGB LED
4 RGB_HEADER1
p.1 No. 7
AURA RGB
RGB LED
LED
126
�简体中文
1 简介
感谢您购买华擎 Fatal1ty B250M Performance Series 主板，这是按照华擎 一贯严
格质量控制标准生产的性能可靠的主板。它提供符合华擎质量和耐久性承诺的
精良设计和卓越性能。
1.1 包装清单
• 华擎 Fatal1ty B250M Performance Series 主板（Micro ATX 规格尺寸）
• 华擎 Fatal1ty B250M Performance Series 快速安装指南
• 华擎 Fatal1ty B250M Performance Series 支持光盘
• 2 x 串行 ATA (SATA) 数据线（选购）
• 2 x 螺丝（供 M.2 插座使用）（选购）
• 1 x I/O 面板
由于主板规格和 BIOS 软件可能已更新，因此，本文档的内容可能会随时更改，
恕不另行通知。如果本文档有任何修改，则更新的版本将发布在华擎网站上，
我们不会另外进行通知。如果您需要与此主板相关的技术支持，请访问我们的
网站以具体了解所用型号的信息。您也可以在华擎网站上找到最新 VGA 卡和
CPU 支持列表。华擎网站 http://www.asrock.com。
127
�简体中文
Fatal1ty B250M Performance Series
1.2 规格
平台
• Micro ATX 规格尺寸
CPU
• 支持第 7
代和第 6 代 Intel® Core
TM
i7/i5/i3/Pentium®/Celeron®
处理器 (Socket 1151)
•
Digi Power design
• 6 电源相设计
• 支持 Intel® Turbo Boost 2.0 技术
芯片集
• Intel® B250
内存
• 双通道 DDR4 内存技术
• 4 x DDR4 DIMM 槽
• 支持 DDR4 2400/2133 非 ECC，非缓冲内存 *
* 第 7 代 Intel® CPU 支持 DDR4 最高达 2400，第 6 代 Intel®
CPU 支持 DDR4 最高达 2133。
• 支持 ECC UDIMM 内存模块（非 ECC 模式操作）
• 支持系统内存最大容量： 64GB
• 支持 Intel® Extreme Memory Prole (XMP) 2.0
• DIMM 插槽中 15μ 金触点
扩充槽
• 2 x PCI Express 3.0 x16 槽 (PCIE1:x16 模式；PCIE4:x4 模式 )*
* 支持 NVMe SSD 用作启动盘
• 2 x PCI Express 3.0 x1 槽 (Flexible PCIe)
• 支持 AMD Quad CrossFireX
TM
和 CrossFireX
TM
• VGA PCIe 插槽 (PCIE1) 中 15μ 金触点
128
�简体中文
图形
• 只有 GPU 集成的处理器才支持 Intel® HD Graphics 内置视
效和 VGA 输出。
• 支持 Intel® HD Graphics 内置视效 : Intel® 快速同步视频，采
用 AVC、MVC (S3D) 和 MPEG-2 Full HW Encode1、Intel®
InTru
TM
3D、Intel® Clear Video HD 技术、Intel® Insider
TM
、
Intel® HD Graphics
• Gen9 LP, DX11.3, DX12
• HWA 编码 / 解码 : VP8, HEVC 8b, VP9, HEVC 10b ( 适用于
第 7 代 Intel® CPU)
• HWA 编码 / 解码 : VP8 , HEVC 8b; GPU/SW 编码 / 解码 :
VP9, HEVC 10b ( 适用于第 6 代 Intel® CPU)
• 最大共享内存 1,024MB
* 最大共享内存大小视操作系统而定。
• 3 个图形输出选项： D-Sub、DVI-D 和 HDMI
• 支持三台显示器
• 支持 HDMI，24Hz 时最大分辨率可达 4K x 2K
(4096x2160)/30Hz 时可达 (3840x2160)
• 支持 DVI-D，60Hz 时最大分辨率达 1920x1200
• 支持 D-Sub，60Hz 时最大分辨率达 1920x1200
• 通过 HDMI 端口（需要兼容的 HDMI 显示器）支持 Auto
Lip Sync、Deep Color (12bpc), xvYCC 和 HBR（高位速率音
频）
• 通过 DVI-D 和 HDMI 端口支持 HDCP
• 通过 DVI-D 和 HDMI 端口支持全高清 1080p Blu-ray (BD)
播放
音频
• 具有内容保护功能的 7.1 CH 高清音频（Realtek ALC892 音
频编解码器）
* 要配置 7.1 CH 高清音频，需要使用高清前面板模块和通过
音频驱动程序启用多通道音频功能。
• 优质 Blu-ray 音频支持
• 支持电涌保护（华擎全防护）
• Nichicon Fine Gold 系列音频电容
• 支持 Creative SoundBlaster Cinema3
LAN
• Gigabit LAN 10/100/1000 Mb/s
• Giga PHY Intel® I219V
• 支持 Wake-On-LAN（网上唤醒）
• 支持雷电 /ESD 保护（华擎全防护）
• 支持高能效以太网 802.3az
• 支持 PXE
129
�简体中文
Fatal1ty B250M Performance Series
后面板 I/O
• 1 x PS/2 鼠标端口
• 1 x PS/2 键盘端口
• 1 x D-Sub 端口
• 1 x DVI-D 端口
• 1 x HDMI 端口
• 1 x USB 2.0 端口（支持 ESD 保护，即华擎全防护）
• 1 x Fatal1ty 鼠标端口（USB 2.0，支持 ESD 保护，即华擎全
防护）
• 3 x USB 3.0 类型 A 端口（支持 ESD 保护，即华擎全防护）
• 1 x USB 3.0 类型 C 端口（支持 ESD 保护，即华擎全防护）
• 1 x RJ-45 LAN 端口，带 LED（ACT/LINK LED 和 SPEED
LED）
• 高清音频插孔 : 线路输入 / 前扬声器 / 麦克风
存储
• 6 x SATA3 6.0 Gb/s 接口，支持 NCQ、AHCI 和热插 拔 *
* 如果 M2_1 被 SATA 型 M.2 设备占用，SATA3_0 将被禁用。
• 1 x 超级 M.2 接口 (M2_1)，支持 2230/2242/2260/2280 M.2
SATA3 6.0 Gb/s 类型模块和 M.2 PCI Express 模块（最高
Gen3 x4 (32 Gb/s)）**
• 1 x 超级 M.2 接口 (M2_1)，支持 2230/2242/2260/2280 M.2
PCI Express 类型模块（最高 Gen3 x4，32 Gb/s）**
** 如果占用 PCIE2 插槽或 PCIE3 插槽，M2_1 插座上的 PCIe
式 M.2 装置将以 Gen3 x2 (16 Gb/s) 运行。
** 支持 Intel® Optane
TM
Technology (M2_2)
** 支持 NVMe SSD 用作启动盘
** 支持华擎 U.2 套件
接口
• 1 x 打印端口接脚
• 1 x COM 端口接头
• 1 x TPM 接脚
• 1 x 机箱侵入和扬声器接脚
• 2 x CPU 风扇接口（1 x 4 针 , 1 x 3 针）
* CPU 风扇接口支持最高 1A (12W) 功率的 CPU 风扇。
• 2 x 机箱风扇接口（4 针）（智能风扇速度控制）
* CHA_FAN1 和 CHA_FAN2 可以自动检测 3 针脚或 4 针脚风
扇是否在使用
• 1 x 24 针 ATX 电源接口
• 1 x 8 针 12V 电源接口
• 1 x 前面板音频接口
130
�简体中文
* 有关详细产品信息，请访问我们的网站： http://www.asrock.com
• 2 x USB 2.0 接脚（支持 4 个 USB 2.0 端口，支持 ESD 保护，
即华擎全防护）
• 1 x USB 3.0 接脚（支持 2 个 USB 3.0 端口，支持 ESD 保护，
即华擎全防护）
BIOS 功能
特点
• AMI UEFI Legal BIOS，支持多语言 GUI
• ACPI 6.0 兼容唤醒事件
• SMBIOS 2.7 支持
• CPU、GT_CPU、DRAM、PCH 1.0V、VCCIO、VCCSA、
VCCST 电压多次调整
硬件监控
• CPU/ 机箱温度感测
• CPU/ 机箱风扇转速计
• CPU/ 机箱静音风扇（根据 CPU 温度自动调整机箱风扇速
度）
• CPU/ 机箱风扇多种速度控制
• CASE OPEN（机箱打开）检测
• 电压监控： +12V、+5V、+3.3V、CPU Vcore、DRAM、
PCH 1.0V
操作系统
• Microso® Windows® 10 64-bit ( 适用于第 7
代 Intel® CPU)
• Microso® Windows® 10 64-bit / 8.1 64-bit / 7 32-bit / 7 64-bit
( 适用于第 6 代 Intel® CPU)
* 要安装 Windows® 7 OS，需要 xHCI 驱动程序已封装到 ISO
文件的经修改的安装盘。请参考第 153 页了解详情。
* 有关已更新的 Windows® 10 驱动程序，请访问华擎网站了解
详情 :http://www.asrock.com
认证
• FCC, CE, WHQL, RCM, BSMI
• ErP/EuP 支持（需要支持 ErP/EuP 的电源）
131
�简体中文
Fatal1ty B250M Performance Series
须认识到超频会有一定风险，包括调整 BIOS 设置，应用“自由超频技术”，
或使用第三方超频工具。超频可能会影响到系统的稳定性，甚至对系统的组件
和设备造成损坏。执行这项工作您应自担风险和自己承担费用。我们对由于超
频而造成的损坏概不负责。
132
�简体中文
1.3 板载接脚和接口
系统面板接脚
(9 针 PANEL1)
（见第 1 页， 第 19 个）
按照下面的针脚分配，
将机箱上的电源开关、
重置开关和系统状态指
示灯连接到此接脚。在
连接线缆前请记下正负
针脚。
PWRBTN（电源开关）:
连接到机箱前面板上的电源开关。您可以配置使用电源开关关闭系统的方式。
RESET（重置开关）:
连接到机箱前面板上的重置开关。如果计算机死机，无法执行正常重新启动，
按重置开关重新启动计算机。
PLED（系统电源 LED）:
连接到机箱前面板上的电源状态指示灯。系统操作操作时，此 LED 亮起。系统
处在 S1/S3 睡眠状态时，此 LED 闪烁。系统处在 S4 睡眠状态或关机 (S5) 时，
此 LED 熄灭。
HDLED（硬盘活动 LED）:
连接到机箱前面板上的硬盘活动 LED 指示灯。硬盘正在读取或写入数据时，此
LED 亮起。
前面板设计根据机箱不同而有所差异。前面板模块主要包括电源开关、重置开
关、电源 LED、硬盘活动 LED 指示灯、扬声器等。将机箱前面板模块连接到此
接脚时，确保连线分配和针脚分配正确匹配。
板载接脚和接口不是跳线。不要将跳线帽装到这些接脚和接口上。将跳线帽装
到这些接脚和接口上将会对主板造成永久性损坏。
GND
R ESET#
P WRBTN#
P LED-
P LED+
GND
H DLED-
H DLED+
1
GND
133
�简体中文
Fatal1ty B250M Performance Series
机箱侵入和扬声器接脚
(7 针 SPK_CI1)
（见第 1 页，第 18 个）
请将机箱侵入和机箱扬
声器连接到到此接脚。
串行 ATA3 接口
(SATA3_0:
见第 1 页， 第 10 个）
(SATA3_1:
见第 1 页， 第 11 个）
(SATA3_2:
见第 1 页，第 13 个）
(SATA3_3:
见第 1 页，第 14 个）
(SATA3_4:
见第 1 页，第 16 个）
(SATA3_5:
见第 1 页，第 15 个）
这六个 SATA3 接口支持
最高 6.0 Gb/s 数据传输
速率的内部存储设备的
SATA 数据线。
如果 M2_1 被 SATA 型
M.2 设备占用，SATA3_0
将被禁用。
USB 2.0 接脚
（9- 针 USB3_4）
（见第 1 页，第 21 个）
（9- 针 USB5_6）
（见第 1 页，第 20 个）
此主板上有 2 个接脚。
每个 USB 2.0 接脚可以支
持两个端口。
USB 3.0 接脚
(19 针 USB3_5_6)
（见第 1 页，第 9 个）
此主板上有 1 个接脚。
每个 USB 3.0 接脚可以支
持两个端口。
1
IntA_ PB_D +
Dummy
IntA_ PB_D -
GND
IntA_ PB_S ST X +
GND
IntA_ PB_S ST X -
IntA_ PB_S SR X +
IntA_ PB_S SR X -
VbusVbus
Vbus
IntA_ PA_S SR X -
IntA_ PA_S SR X +
GND
IntA_ PA_S ST X -
IntA_ PA_S ST X +
GND
IntA_ PA_D -
IntA_ PA_D +
1
+5V
DUMMY
SIGNAL
GND
DUMMY
SPEAKER
DUMMY
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
USB_PWR
1
SATA3_4
SATA3_5
SATA3_2
SATA3_3
SATA3_1
SATA3_0
134
�简体中文
前面板音频接脚
(9 针 HD_AUDIO1)
（见第 1 页，第 25 个）
此接脚用于将音频设备
连接到前音频面板。
机箱风扇接口
(4 针 CHA_FAN1)
（见第 1 页， 第 2 个）
(4 针 CHA_FAN2)
（见第 1 页， 第 12 个）
请将风扇线连接到风扇
接口并使黑线匹配接地
针脚。
CPU 风扇接口
(4 针 CPU_FAN1)
（见第 1 页， 第 3 个）
(3 针 CPU_FAN2)
（见第 1 页， 第 4 个）
此主板提供 4 针 CPU 风
扇（静音风扇）接口。如
果您打算连接 3 针 CPU
风扇，请将它连接到针
脚 1-3。
1.
高清音频支持插孔感测，但机箱上的面板连线必须支持 HDA 才能正常工作。
请按照我们的手册和机箱手册的说明安装系统。
2.
如果您使用 AC’97 音频面板，请按照以下步骤将它安装到前面板音频接脚：
A. 将 Mic_IN (MIC) 连接到 MIC2_L。
B. 将 Audio_R (RIN) 连接到 OUT2_R，将 Audio_L (LIN) 连接到 OUT2_L。
C. 将接地端 (GND) 连接到接地端 (GND)。
D. MIC_RET 和 OUT_RET 只用于高清音频面板。您不需要针对 AC’97 音频
面板连接它们。
E. 要启用前麦克风，请转到 Realtek 控制面板上的“FrontMic”（前麦克风）
选项卡，调整 “Recording Volume”（录音音量）。
GND
FAN_VOLTAGE_ CONTROL
FAN_SPEE D
FAN_SPEE D_CONTROL
J _SENSE
O UT2_L
1
M IC_RET
P RESENCE#
GN D
O UT2_R
M IC2_R
M IC2_L
OUT_RET
GND
FAN_VOLTAGE_CO NTROL
FAN_SPEED
FAN_SPEED _CONTROL
FAN_VOLTAGE
GND
FAN_SPEED
FAN_SPEED_CONTROL
1
2
3
4
GND
FA N_VOLTAGE
FA N_SPEED
135
�简体中文
Fatal1ty B250M Performance Series
ATX 电源接口
(24 针 ATXPWR1)
（见第 1 页，第 8 个）
此主板提供 24 针 ATX
电源接口。要使用 20 针
ATX 电源，请沿针脚 1
和针脚 13 插接它。
ATX 12V 电源接口
(8 针 ATX12V1)
（见第 1 页，第 1 个）
此主板提供 8 针 ATX
12V 电源接口。要使用 4
针 ATX 电源，请沿针脚
1 和针脚 5 插接它。
串行端口接脚
(9 针 COM1)
（见第 1 页，第 24 个）
此 COM1 接脚支持串行
端口模块。
TPM 接脚
(17 针 TPMS1)
（见第 1 页，第 22 个）
此接口支持 Trusted Platform
Module（信任平台模块，
TPM）系统，可以安全地存储
密钥、数字证书、密码和数据。
TPM 系统也可以帮助增强网络
安全，保护数字身份和确保平
台完整性。
打印端口接脚
(25 针 LPT1)
（见第 1 页，第 23 个）
这是一个打印端口线缆
接口，通过它可以方便
地连接到打印机设备。
AURA RGB LED 接脚
(4 针 RGB_HEADER1)
（见第 1 页，第 7 个）
AURA RGB LED 接脚用
于连接 RGB LED 延长
线，可让用户选择不同
的 LED 灯光效果。
1
GN D
SM B _DATA_MAIN
LA D 2
LA D 1
GN D
S_ P WRDWN #
SE R IRQ #
GN
D
P C I C L K
P C I R ST #
LA D 3
+3 V
LA D 0
+3VS B
GN D
FR A M E
SM B _CLK_MAIN
12
1
24
13
5
1
8
4
1
AF D #
ER R OR#
PI N IT#
GN D
SL I N#
ST B #
SP D 0
SP D 1
SP D 2
SP D 3
SP D 4
SP D 5
SP D 6
SP D 7
AC K #
BU S Y
PE
SL C T
136
�简体中文
电子信息产品污染控制标示
依据中国发布的「电子信息产品污染控制管理办法」及 SJ/T 11364-2006「电子
信息产品污染控制标示要求」，电子信息产品应进行标示，藉以向消费者揭露
产品中含有的有毒有害物质或元素不致发生外泄或突变从而对环境造成污染或
对人身、财产造成严重损害的期限。依上述规定，您可于本产品之印刷电路板
上看见图一之标示。图一中之数字为产品之环保使用期限。由此可知此主板之
环保使用期限为 10 年。
图一
有毒有害物质或元素的名称及含量说明
若您欲了解此产品的有毒有害物质或元素的名称及含量说明，请参照以下表格
及说明。
有害物质或元素
铅 (Pb) 镉 (Cd) 汞 (Hg) 六价铬 (Cr(VI)) 多溴联苯 (PBB) 多溴二苯醚 (PBDE)
印刷电路板
及电子组件
外部信号连
接头及线材
部件名称
X O O O O O
X O O O O O
O: 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定
的限量要求以下。
X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准
规定的限量要求，然该部件仍符合欧盟指令 2002/95/EC 的规范。
备注 : 此产品所标示之环保使用年限，系指在一般正常使用状况下。
137
繁體中文
Fatal1ty B250M Performance Series
1 簡介
感謝您購買華擎 Fatal1ty B250M Performance Series 主機板，本主機板經華擎嚴
格品管製作，是一套讓人信賴的可靠產品。本產品採耐用設計所展現的優異效
能，完全符合華擎對品質及耐用度的承諾。
1.1 包裝內容
• 華擎 Fatal1ty B250M Performance Series 主機板（Micro ATX 尺寸）
• 華擎 Fatal1ty B250M Performance Series 快速安裝指南
• 華擎 Fatal1ty B250M Performance Series 支援光碟
• 2 x Serial ATA (SATA) 資料纜線（選用）
• 2 x 螺絲（適用於 M.2 插座）（選用）
• 1 x I/O 面板外罩
由於主機板規格及 BIOS 軟體可能會更新，所以本文件內容如有變更，恕不另
行通知。如本文件有任何修改，可至華擎網站逕行取得更新版本，不另外通知。
若您需要與本主機板相關的技術支援，請上我們的網站瞭解有關您使用機型的
特定資訊。您也可以在華擎網站找到最新的 VGA 卡及 CPU 支援清單。華擎網
站 http://www.asrock.com。
138
繁體中文
1.2 規格
平台
• Micro ATX 尺寸
CPU
• 支援第 7 代與第 6 代 Intel® Core
TM
i7/i5/i3/Pentium®/Celeron®
處理器（插座 1151）
•
Digi Power design
• 6 電源相位設計
• 支援 Intel® Turbo Boost 2.0 技術
晶片組
• Intel® B250
記憶體
• 雙通道 DDR4 記憶體技術
• 4 x DDR4 DIMM 插槽
• 支援 DDR4 2400/2133 非 ECC、無緩衝記憶體 *
* 第 7 代 Intel® CPU 支援最高 2400 DDR4；第 6 代 Intel® CPU
支援最高 2133 DDR4。
• 支援 ECC UDIMM 記憶體模組 ( 於非 ECC 模式下運作 )
• 最大系統記憶體容量： 64GB
• 支援 Intel® Extreme Memory Prole (XMP) 2.0
• 15μ 特厚鍍金插槽
擴充插槽
• 2 x PCI Express 3.0 x16 插槽（PCIE1：x16 模式；PCIE4：
x4 模式 )*
* 支援 NVMe SSD 作為開機磁碟
• 2 x PCI Express 3.0 x1 插槽 (Flexible PCIe)
• 支援 AMD Quad CrossFireX
TM
及 CrossFireX
TM
• VGA PCIe 插槽採用 15μ 金接點 (PCIE1)
139
繁體中文
Fatal1ty B250M Performance Series
顯示卡
• 僅限整合 GPU 的處理器才可支援 Intel® HD Graphics
Built-in Visuals 及 VGA 輸出。
• 支援 Intel® HD Graphics Built-in Visuals： 轉換 AVC、
MVC (S3D) 及 MPEG-2 Full HW Encode1 的 Intel® 高速影
像同步轉檔技術、Intel® InTru
TM
3D, Intel® Clear Video HD
Technology、Intel® Insider
TM
、Intel® HD Graphics
• Gen9 LP、DX11.3、DX12
• HWA 編碼 / 解碼： VP8、HEVC 8b、VP9、HEVC 10b ( 適
用於第 7 代 Intel® CPU)
• HWA 編碼 / 解碼： VP8、HEVC 8b；GPU/SW 編碼 / 解碼：
VP9、HEVC 10b ( 適用於第 6 代 Intel® CPU)
• 最大共用記憶體 1024MB
* 最大共用記憶體的大小可能會隨著作業系統的不同而改變。
• 三個圖形輸出選項： D-Sub、DVI-D 及 HDMI
• 支援三台顯示器
• 支援最高可達 4K x 2K (4096x2160) @ 24Hz / (3840x2160) @
30Hz 解析度的 HDMI
• 支援最高達 1920x1200 @ 60Hz 解析度的 DVI-D
• 最高支援 1920x1200 @ 60Hz 解析度的 D-Sub
• 支援使用 HDMI 連接埠（需相容於 HDMI 監視器）的
Auto Lip Sync、Deep Color (12bpc)、xvYCC 及 HBR（高位
元率音訊）
• 支援含 DVI-D 及 HDMI 連接埠的 HDCP
• 支援透過 DVI-D 及 HDMI 連接埠的 Full HD 1080p 藍光
(BD) 播放
音訊
• 7.1 CH HD 音訊含內容保護（Realtek ALC892 音訊轉碼器）
功能
* 若要設定 7.1 CH HD 音訊，必須使用 HD 前面板音訊模組，
並透過音訊驅動程式啟用多聲道音訊功能。
• 高階藍光音訊支援
• 支援突波保護（華擎全防護）
• Nichicon Fine Gold 系列音響級電容
• 支援 Creative SoundBlaster Cinema3
LAN
• Gigabit LAN 10/100/1000 Mb/s
• Giga PHY Intel® I219V
• 支援網路喚醒
• 支援雷擊／靜電保護（華擎全防護）
• 支援 Energy Ecient Ethernet 802.3az
• 支援 PXE
140
繁體中文
後面板 I/O
• 1 x PS/2 滑鼠連接埠
• 1 x PS/2 鍵盤連接埠
• 1 x D-Sub 連接埠
• 1 x DVI-D 連接埠
• 1 x HDMI 連接埠
• 1 x USB 2.0 連接埠（支援靜電保護（華擎全防護））
• 1 x Fatal1ty 滑鼠連接埠 (USB 2.0)（支援靜電保護（華擎全
防護））
• 3 x USB 3.0 Type-A 連接埠（支援靜電保護（華擎全防護））
• 1 x USB 3.0 Type-C 連接埠（支援靜電保護（華擎全防護））
• 1 x RJ-45 LAN 連接埠，含 LED（ACT/LINK LED 及 SPEED
LED）
• HD 音訊插孔： 線路輸入／前置喇叭／麥克風
儲存裝置
• 6 x SATA3 6.0 Gb/s 接頭支援 NCQ、AHCI 及熱插拔 *
* 若 M2_1 為 SATA 類型的 M.2 裝置佔用，將會停用
SATA3_0。
• 1 x Ultra M.2 插座 (M2_1)，支援 2230/2242/2260/2280 M.2
SATA3 6.0 Gb/s 模組與 M.2 PCI Express 模組（最高可達
Gen3 x4 (32 Gb/s)）類型 **
• 1 x Ultra M.2 插座 (M2_2)，支援 2230/2242/2260/2280 M.2
PCI Express 模組（最高可達 Gen3 x4 (32 Gb/s)）**
** 若佔用 PCIE2 插槽或 PCIE3 插槽，M2_1 插座上的 PCIe 式
M.2 裝置將以 Gen3 x2 (16 Gb/s) 執行。
** 支援 Intel® Optane
TM
技術 (M2_2)
** 支援 NVMe SSD 作為開機磁碟
** 支持華擎 U.2 套件
接頭
• 1 x 列印連接埠標頭
• 1 x COM 連接埠排針
• 1 x TPM 排針
• 1 x 機殼防護排針
• 2 x CPU 風扇接頭 (1 x 4-pin、1 x 3-pin)
* CPU 風扇接頭支援最高 1A (12W) 風扇功率的 CPU 風扇。
• 2 x 機殼風扇接頭 (4-pin)（智慧型風扇速度控制）
* 如果 3-pin 或 4-pin 風扇使用中，可自動偵測 CHA_FAN1 和
CHA_FAN2。
• 1 x 24 pin ATX 電源接頭
• 1 x 8 pin 12V 電源接頭
• 1 x 前面板音訊接頭
141
繁體中文
Fatal1ty B250M Performance Series
* 如需產品詳細資訊，請上我們的網站： http://www.asrock.com
• 2 x USB 2.0 排針（支援 4 個 USB 2.0 連接埠）（支援靜電
保護 ( 華擎全防護 )）
• 1 x USB 3.0 排針（支援 2 個 USB 3.0 連接埠）（支援靜電
保護（華擎全防護））
BIOS 功能
• AMI UEFI Legal BIOS 含多語 GUI 支援
• ACPI 6.0 符合喚醒自動開機
• 支援 SMBIOS 2.7
• CPU、GT_CPU、DRAM、PCH 1.0V、VCCIO、VCCSA、
VCCST 電壓多重調整
硬體監視器
• CPU ／機殼溫度感應
• CPU ／機殼風扇轉速計
• CPU ／機殼靜音風扇（依 CPU 溫度自動調整機殼風扇速
度）
• CPU ／機殼風扇多重速度控制
• 機殼開啟偵測
• 電壓監控： +12V、+5V、+3.3V、CPU Vcore、DRAM、
PCH 1.0V
作業系統
• Microso® Windows® 10 64 位元 ( 適用於第 7 代 Intel® CPU)
• Microso® Windows® 10 64 位元／ 8.1 64 位元／ 7 32 位元／
7 64 位元 ( 適用於第 6 代 Intel® CPU)
* 若要安裝 Windows® 7 作業系統，需要使用修改過的安裝光
碟（已將 xHCI 驅動程式封裝至 ISO 檔案）。如需詳細說明，
請查看第 153 頁。
* 關於最新 Windows® 10 驅動程式的詳細資訊，請瀏覽華擎網
站：http://www.asrock.com
認證
• FCC、CE、WHQL、RCM、BSMI
• ErP/EuP Ready（需具備 ErP/EuP ready 電源供應器）
142
繁體中文
請務必理解，超頻可能產生某種程度的風險，其中包括調整 BIOS 中的設定、
採用自由超頻技術或使用協力廠商的超頻工具。超頻可能會影響您系統的穩定
性，或者甚至會對您系統的元件及裝置造成傷害。您應自行負擔超頻風險及成
本。我們對於因超頻所造成的可能損害概不負責。
143
繁體中文
Fatal1ty B250M Performance Series
1.3 板載排針及接頭
系統面板排針
(9-pin PANEL1)
（請參閱第 1 頁， 編號 19）
請依照以下的針腳
排列將機殼上的電
源開關、重設開關
及系統狀態指示燈
連接至此排針。在
連接纜線之前請注
意正負針腳。
PWRBTN ( 電源開關 )：
連接至機殼前面板上的電源開關。您可設定使用電源開關關閉系統電源的方
式。
RESET ( 重設開關 )：
連接至機殼前面板上的重設開關。若電腦凍結且無法執行正常重新啟動，按下
重設開關即可重新啟動電腦。
PLED ( 系統電源 LED)：
連接至機殼前面板上的電源狀態指示燈。系統正在運作時，此 LED 會亮起。系
統進入 S1/S3 睡眠狀態時，LED 會持續閃爍。系統進入 S4 睡眠狀態或關機 (S5)
時，LED 會熄滅。
HDLED ( 硬碟活動 LED)：
連接至機殼前面板上的硬碟活動 LED。硬碟正在讀取或寫入資料時，LED 會亮
起。
各機殼的前面板設計各有不同。前面板模組主要是由電源開關、重設開關、電
源 LED、硬碟活動 LED、喇叭及其他裝置組成。將機殼前面板模組連接至此排
針時，請確定佈線及針腳指派皆正確相符。
板載排針及接頭都不是跳線。請勿將跳線帽套在這些排針及接頭上。將跳線帽
套在排針及接頭上，將造成主機板永久性的受損。
GND
R ESET#
P WRBTN#
P LED-
P LED+
GND
H DLED-
H DLED+
1
GND
144
繁體中文
機殼防護排針
(7-pin SPK_CI1)
（請參閱第 1 頁，編號 18）
機殼防護排針連接
至此排針。
Serial ATA3 接頭
(SATA3_0:
請參閱第 1 頁，編號 10）
(SATA3_1:
請參閱第 1 頁，編號 11）
(SATA3_2:
請參閱第 1 頁，編號 13）
(SATA3_3:
請參閱第 1 頁，編號 14）
(SATA3_4:
請參閱第 1 頁，編號 16）
(SATA3_5:
請參閱第 1 頁，編號 15）
這六組 SATA3 接頭
皆支援內部儲存裝
置的 SATA 資料纜
線，最高可達 6.0
Gb/s 資料傳輸率。
若 M2_1 為 SATA
類型的 M.2 裝置
佔用，將會停用
SATA3_0。
USB 2.0 排針
(9-pin USB3_4)
（請參閱第 1 頁，編號 21）
(9-pin USB5_6)
（請參閱第 1 頁，編號 20）
本主機板上含有兩
組排針。各 USB 2.0
排針皆可支援兩個
連接埠。
USB 3.0 排針
(19-pin USB3_5_6)
（請參閱第 1 頁，編號 9）
本主機板上含有一
組排針。各 USB 3.0
排針皆可支援兩個
連接埠。
1
IntA_ PB_D +
Dummy
IntA_ PB_D -
GND
IntA_ PB_S ST X +
GND
IntA_ PB_S ST X -
IntA_ PB_S SR X +
IntA_ PB_S SR X -
VbusVbus
Vbus
IntA_ PA_S SR X -
IntA_ PA_S SR X +
GND
IntA_ PA_S ST X -
IntA_ PA_S ST X +
GND
IntA_ PA_D -
IntA_ PA_D +
1
+5V
DUMMY
SIGNAL
GND
DUMMY
SPEAKER
DUMMY
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
USB_PWR
1
SATA3_4
SATA3_5
SATA3_2
SATA3_3
SATA3_1
SATA3_0
145
繁體中文
Fatal1ty B250M Performance Series
前面板音訊排針
(9-pin HD_AUDIO1)
（請參閱第 1 頁，編號 25）
本排針適用於連接
音訊裝置至前面板
音訊。
機殼風扇接頭
(4-pin CHA_FAN1)
（請參閱第 1 頁， 編號 2）
(4-pin CHA_FAN2)
（請參閱第 1 頁， 編號 12）
請將風扇纜線連接
至風扇接頭，並比
對黑線及接地針
腳。
CPU 風扇接頭
(4-pin CPU_FAN1)
（請參閱第 1 頁， 編號 3）
(3-pin CPU_FAN2)
（請參閱第 1 頁， 編號 4）
本主機板配備 4-Pin
CPU 風扇 ( 靜音風
扇 ) 接頭。若您計
畫連接 3-Pin CPU
風扇，請接至 Pin
1-3。
1.
高解析度音訊支援智慧型音效介面偵測 (Jack Sensing)，但機殼上的面板線必
須支援 HDA 才能正確運作。請依本手冊及機殼手冊說明安裝系統。
2.
若您使用 AC’97 音訊面板，請按照以下步驟安裝至前面板音訊排針：
A. 將 Mic_IN (MIC) 連接至 MIC2_L。
B. 將 Audio_R (RIN) 連接至 OUT2_R 且將 Audio_L (LIN) 連接至 OUT2_L。
C. 將接地 (GND) 連接至接地 (GND)。
D. MIC_RET 及 OUT_RET 僅供 HD 音訊面板使用。您不需要在 AC’97 音訊
面板上連接。
E. 若要啟動前側麥克風，請前往 Realtek 控制面板中的「FrontMic」標籤調整
「錄音音量」。
GND
FAN_VOLTAGE_ CONTROL
FAN_SPEE D
FAN_SPEE D_CONTROL
J _SENSE
O UT2_L
1
M IC_RET
P RESENCE#
GN D
O UT2_R
M IC2_R
M IC2_L
OUT_RET
GND
FAN_VOLTAGE_CO NTROL
FAN_SPEED
FAN_SPEED _CONTROL
FAN_VOLTAGE
GND
FAN_SPEED
FAN_SPEED_CONTROL
1
2
3
4
GND
FA N_VOLTAGE
FA N_SPEED
146
繁體中文
ATX 電源接頭
(24-pin ATXPWR1)
（請參閱第 1 頁，編號 8）
本主機板配備一組
24-pin ATX 電源接
頭。若要使用 20-
pin ATX 電源供應
器，請插入 Pin 1
及 Pin 13。
ATX 12V 電源接頭
(8-pin ATX12V1)
（請參閱第 1 頁，編號 1）
本主機板配備一組
8-pin ATX 12V 電
源接頭。若要使用
4-pin ATX 電源供
應器，請插入 Pin 1
及 Pin 5。
序列連接埠排針
(9-pin COM1)
（請參閱第 1 頁，編號 24）
此 COM1 排針支援
序列連接埠模組。
TPM 標頭
(17-pin TPMS1)
（請參閱第 1 頁，編號 22）
此接頭支援信賴平台模組
(TPM) 系統，可確保儲存
金鑰、數位憑證、密碼及
資料的安全。TPM 系統
也能強化網路安全、保護
數位身分並確定平台完整
性。
列印連接埠標頭
(25-pin LPT1)
（請參閱第 1 頁，編號 23）
這是供列印連接埠
纜線使用的介面，
可方便印表機裝置
連線。
1
GN D
SM B _DATA_MAIN
LA D 2
LA D 1
GN D
S_ P WRDWN #
SE R IRQ #
GN
D
P C I C L K
P C I R ST #
LA D 3
+3 V
LA D 0
+3VS B
GN D
FR A M E
SM B _CLK_MAIN
12
1
24
13
5
1
8
4
1
AF D #
ER R OR#
PI N IT#
GN D
SL I N#
ST B #
SP D 0
SP D 1
SP D 2
SP D 3
SP D 4
SP D 5
SP D 6
SP D 7
AC K #
BU S Y
PE
SL C T
147
繁體中文
Fatal1ty B250M Performance Series
AURA RGB LED 排針
(4-pin RGB_HEADER1)
（請參閱第 1 頁，編號 7）
AURA RGB LED 排
針用於連接 RGB
LED 延長線，可
供使用者選擇各種
LED 照明效果。
148
Bahasa Indonesia
Spesikasi
Platform
•
Bentuk dan Ukuran Micro ATX
CPU
•
Mendukung Prosesor Intel® Core
TM
i7/i5/i3/Pentium®/Celeron®
(Soket 1151) Generasi ke-7 dan ke-6
•
Digi Power design
•
Desain 6 Fase Daya
•
Mendukung Teknologi Intel® Turbo Boost 2.0
Chipset
•
Intel® B250
Memori
•
Teknologi Memori DDR4 Kanal Ganda
•
4 x Slot DDR4 DIMM
•
Mendukung DDR4 2400/2133 non-ECC, memori tanpa buer*
* Generasi ke-7 untuk CPU Intel® mendukung DDR4 hingga 2400;
Generasi ke-6 untuk CPU Intel® CPU mendukung DDR4 hingga
2133.
•
Mendukung modul memori ECC UDIMM (berjalan dalam
mode non-ECC)
•
Kapasitas maksimum memori sistem: 64GB
•
Mendukung Intel® Extreme Memory Prole (XMP) 2.0
•
15μ Bidang Kontak berwarna Emas di Slot DIMM
Slot
Ekspansi
•
2 x Slot PCI Express 3.0 x16 (PCIE1:x16 mode; PCIE4:x4
mode)*
* Mendukung NVMe SSD sebagai disk boot
•
2 x slot PCI Express 3.0 x1 (Flexible PCIe)
•
Mendukung AMD Quad CrossFireX
TM
dan CrossFireX
TM
•
15μ Bidang Kontak berwarna Emas di Slot VGA PCIe (PCIE1)
Gras
•
Intel® HD Graphics Built-in Visuals dan output VGA hanya
didukung dengan prosesor yang terintegrasi GPU.
•
Mendukung Intel® HD Graphics Built-in Visuals: Intel® Quick
Sync Video dengan AVC, MVC (S3D) dan MPEG-2 Full HW
Encode1, Intel® InTru
TM
3D, Intel® Clear Video HD Technology,
Intel® Insider
TM
, Intel® HD Graphics
•
LP Generasi ke-9, DX11.3, DX12
•
Encode/Decode HWA: VP8, HEVC 8b, VP9, HEVC 10b (untuk
CPU Intel® Generasi ke-7)
149
Bahasa Indonesia
Fatal1ty B250M Performance Series
•
Encode/Decode HWA: VP8, HEVC 8b; Encode/Decode GPU/
SW: VP9, HEVC 10b, (untuk CPU Intel® Generasi ke-6 )
•
Memori bersama maksimum 1.024MB
* Ukuran memori bersama maksimum bervariasi di berbagai
sistem operasi.
•
Tiga pilihan output gras: D-Sub, DVI-D, dan HDMI
•
Mendukung Tiga Monitor
•
Mendukung HDMI dengan resolusi maksimum hingga
4K x 2K (4096x2160) @ 24Hz/(3840x2160) @ 30Hz
•
Mendukung DVI-D dengan resolusi maksimum hingga
1920x1200 @ 60Hz
•
Mendukung D-Sub dengan resolusi maksimum hingga
1920x1200 @ 60Hz
•
Mendukung Lip Sync Otomatis, Kedalaman Warna (12bpc),
xvYCC, dan HBR (High Bit Rate Audio) dengan Port HDMI
(memerlukan monitor HDMI yang kompatibel)
•
Mendukung HDCP dengan port DVI-D dan HDMI
•
Mendukung pemutaran 1080p Blu-ray HD Penuh (BD) dengan
Port DVI-D dan HDMI
Audio
•
Audio HD 7.1 CH dengan Perlindungan Konten (Realtek
ALC892 Audio Codec)
*Untuk mengkongurasi Audio HD 7.1 CH, modul audio panel
depan HD harus digunakan dan tur audio multisaluran harus
diaktian melalui driver audio.
•
Mendukung Audio Blu-ray Premium
•
Mendukung Perlindungan Lonjakan Arus (ASRock Full Spike
Protection)
•
Nichicon Fine Gold Series Audio Caps
•
Mendukung Cinema3 SoundBlaster Creative
LAN
•
Gigabit LAN 10/100/1000 Mb/s
•
Giga PHY Intel® I219V
•
Mendukung Wake-On-LAN
•
Mendukung Perlindungan Petir/ESD (Perlindungan ASRock
Full Spike)
•
Mendukung Energy Ecient Ethernet 802.3az
•
Mendukung PXE
150
Bahasa Indonesia
Panel I/O
Belakang
•
1 x Port Mouse PS/2
•
1 x Port Keyboard PS/2
•
1 x Port D-Sub
•
1 x Port DVI-D
•
1 x Port HDMI
•
1 x Port USB 2.0 (Mendukung Perlindungan ESD (ASRock Full
Spike Protection))
•
1 x Port Mouse Fatal1ty (USB 2.0) (Mendukung Perlindungan
ESD (ASRock Full Spike Protection))
•
3 x Port USB 3.0 Tipe A (Mendukung Perlindungan ESD
(Perlindungan ASRock Full Spike))
•
1 x Port USB 3.0 Tipe C (Mendukung Perlindungan ESD
(Perlindungan ASRock Full Spike))
•
1 x Port LAN RJ-45 dengan LED (ACT/LINK LED dan SPEED
LED)
•
Soket Audio HD: Saluran Masuk/Speaker Depan/Mikrofon
Penyimpanan
•
6 x Konektor SATA3 6.0 Gb/s, mendukung NCQ, AHCI, dan
Hot Plug*
* Jika M2_1 digunakan oleh perangkat SATA tipe M.2, maka
SATA3_0 akan dinonaktian.
•
1 x Soket Ultra M.2 (M2_1), mendukung jenis modul
2230/2242/2260/2280 M.2 SATA3 6,0 Gb/s dan modul M.2 PCI
Express hingga Gen3 x4 (32 Gb/s)**
•
1 x Ultra M.2 Socket (M2_2), mendukung jenis modul 2230/
2242/2260/2280 M.2 PCI Express hingga Gen3 x4 (32 Gb/s)**
** Jika slot PCIE2 atau slot PCIE3 digunakan, perangkat M.2 tipe
PCIe pada soket M2_1 akan berjalan pada Gen3 x2 (16 Gb/detik)
** Mendukung Intel® Optane
TM
Technology (M2_2)
** Mendukung NVMe SSD sebagai disk boot
** Mendukung Kit U.2 ASRock
Konektor
•
1 x Header Port Cetak
•
1 x Header Port COM
•
1 x Header TPM
•
1 x Intrusi Chassis dan Header Speaker
•
2 x Konektor Kipas CPU (1 x 4-pin, 1 x 3-pin)
* Konektor Kipas CPU mendukung kipas CPU dengan daya kipas
maksimum 1A (12W).
•
2 x Konektor Kipas Chassis (4-pin) (Kontrol Kecepatan Kipas
Pintar)
* CHA_FAN1 dan CHA_FAN2 dapat mendeteksi otomatis jika
kipas 3-pin atau 4-pin sedang digunakan.
151
Bahasa Indonesia
Fatal1ty B250M Performance Series
* Untuk informasi tentang produk rinci, kunjungi situs web kami: http://www.asrock.com
•
1 x Konektor Daya ATX 24 pin
•
1 x Konektor Daya 8 pin 12V
•
1 x Konektor Audio Panel Depan
•
2 x Header USB 2.0 (Mendukung 4 port USB 2.0) (Mendukung
Perlindungan ESD (Perlindungan ASRock Full Spike))
•
1 x Header USB 3.0 (Mendukung 2 port USB 3.0) (Mendukung
Perlindungan ESD (Perlindungan ASRock Full Spike))
Fitur BIOS
•
AMI UEFI Legal BIOS dengan dukungan GUI multibahasa
•
ACPI 6.0 Kompatibel dengan aktivitas pengaktifan
•
Dukungan SMBIOS 2.7
•
Multipengatur Tegangan CPU, GT_CPU, DRAM, PCH 1,0V,
VCCIO, VCCSA, dan VCCST
Monitor
Perangkat
Keras
•
Sensor suhu CPU/Chassis
•
Takometer Kipas CPU/Chassis
•
Kipas Hening CPU/Chassis (Penyesuaian otomatis kecepatan
kipas berdasarkan suhu CPU)
•
Kontrol multikecepatan Kipas CPU/Chassis
•
Deteksi CASE OPEN
•
Pemantauan tegangan: +12V, +5V, +3,3V, CPU Vcore, DRAM,
PCH 1,0V
OS
•
Microso® Windows® 10 64-bit (Untuk Intel® CPU Generasi
ke-7)
•
Microso® Windows® 10 64-bit / 8.1 64-bit / 7 32-bit / 7 64-bit
(Untuk CPU Intel® Generasi ke-6)
* Untuk menginstal OS Windows® 7, diperlukan disk instalan
termodikasi dengan driver xHCI dalam le ISO. Untuk petunjuk
lebih rinci, lihat halaman 153.
* Untuk driver Windows® 10 terbaru, kunjungi situs web ASRock
untuk mendapatkan info rinci: http://www.asrock.com
Sertikasi
•
FCC, CE, WHQL, RCM, BSMI
•
Siap untuk ErP/EuP (memerlukan catu daya untuk ErP/EuP)
152
Bahasa Indonesia
Perlu diketahui, overclocking memiliki risiko tertentu, termasuk menyesuaikan
pengaturan pada BIOS, menerapkan Teknologi Untied Overclocking, atau menggunakan
alat overclocking pihak ketiga. Overclocking dapat mempengaruhi stabilitas sistem,
atau bahkan dapat mengakibatkan kerusakan komponen dan perangkat sistem. Risiko
dan biaya apapun menjadi tanggungan Anda. Kami tidak bertanggung jawab atas
kemungkinan kerusakan karena overclocking.
153
English
Fatal1ty B250M Performance Series
Enabling USB Ports for Windows® 7 Installation
Intel® new processors have removed their support for the Enhanced Host Controller
Interface (EHCI – USB2.0) and only kept the eXtensible Host Controller Interface
(XHCI – USB3.0). Due to that fact that XHCI is not included in the Windows 7
inbox drivers, users may nd it dicult to install Windows 7 operating system
because the USB ports on their motherboard won’t work. In order for the USB ports
to function properly, please create a Windows® 7 installation disk with the Intel®
USB 3.0 eXtensible Host Controller (xHCI) drivers packed into the ISO le.
Requirements
•
A Windows® 7 installation disk or USB drive
•
A Windows® PC
•
Win7 USB Patcher (included in the ASRock Support CD or downloaded from
website)
Scenarios
You have an ODD and PS/2 ports:
If there is an optical disc drive, PS/2 ports and PS/2 Keyboard or mouse on your computer,
you can skip the instructions below and go ahead to install Windows® 7 OS.
You’ve got nothing:
If you do not have an optical disc drive, please nd another computer and follow the
instructions below to create a new ISO le with the “Win7 USB Patcher”. en use the new
patched Windows® 7 installation USB drive to install Windows® 7 OS.
154
English
Instructions
Step 1
Insert the Windows® 7 installation disk or USB drive to your system.
Step 2
Extract the tool (Win7 USB Patcher) and launch it.
Step 3
Select how you want to install Windows 7 later.
Step 4
Locate your Win7 source folder or your ISO le.
155
English
Fatal1ty B250M Performance Series
Step 5
Select the USB storage, compact disk or destination folder for the new Windows 7
installation le.
Step 6
Click “Start” to begin.
Step 7
Now you are able to install Windows® 7 on Intel® new processors with the new burned CD.
Or please use the patched ISO image to make an OS USB drive to install the OS.
Contact Information
If you need to contact ASRock or want to know more about ASRock, you’re welcome
to visit ASRock’s website at http://www.asrock.com; or you may contact your dealer
for further information. For technical questions, please submit a support request
form at http://www.asrock.com/support/tsd.asp
ASRock Incorporation
2F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District,
Taipei City 112, Taiwan (R.O.C.)
ASRock EUROPE B.V.
Bijsterhuizen 11-11
6546 AR Nijmegen
e Netherlands
Phone: +31-24-345-44-33
Fax: +31-24-345-44-38
ASRock America, Inc.
13848 Magnolia Ave, Chino, CA91710
U.S.A.
Phone: +1-909-590-8308
Fax: +1-909-590-1026
EC-Declaration of Conformity
For the following equipment:
Motherboard
(Product Name)
Fatal1ty B250M Performance Series / ASRock
(Model Designation / Trade Name)
ASRock Incorporation
(Manufacturer Name)
2F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District, Taipei City 112, Taiwan (R.O.C.)
(Manufacturer Address)
is herewith conrmed to comply with the requirements set out in the Council
Directive on the Approximation of the Laws of the Member States relating to
Electromagnetic Compatibility Directive (2004/108/EC) and Safety Directive (2006/95/
EC), the following standards are applied:
☑
EN 55022: 2006+A1:2007
☑
EN 61000-3-2: 2009
☑
EN 61000-3-3: 2008
☑
EN 55024: 1998 + A1:2001 + A2:2003
IEC 61000-4-2: 2008;
IEC 61000-4-3: 2010; IEC 61000-4-4: 2010;
IEC 61000-4-5: 2005; IEC 61000-4-6: 2008;
IEC 61000-4-8: 2009; IEC 61000-4-11: 2004;
☑
EN 60950-1: 2005 + A1:2009
IEC 60950-1: 2006 + A11:2009 + A1:2010 + A12:2011
e following manufacturer / importer or authorized representative established within
the EUT is responsible for this declaration:
ASRock EUROPE B.V.
(Company Name)
Bijsterhuizen 1111 6546 AR Nijmegen e Netherlands
(Company Address)
Person responsible for making this declaration:
(Name, Surname)
A.V.P
(Position / Title)
Nov. 18, 2016
(Date)
P/N: 15G062002000AK V1.0
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
ASROCK FATAL1TY B250M PERFORMANCE Manual de usuario
- Tipo
- Manual de usuario
en otros idiomas
- français: ASROCK FATAL1TY B250M PERFORMANCE Manuel utilisateur
- italiano: ASROCK FATAL1TY B250M PERFORMANCE Manuale utente
- English: ASROCK FATAL1TY B250M PERFORMANCE User manual
- Deutsch: ASROCK FATAL1TY B250M PERFORMANCE Benutzerhandbuch
- русский: ASROCK FATAL1TY B250M PERFORMANCE Руководство пользователя
- português: ASROCK FATAL1TY B250M PERFORMANCE Manual do usuário
- 日本語: ASROCK FATAL1TY B250M PERFORMANCE ユーザーマニュアル
- Türkçe: ASROCK FATAL1TY B250M PERFORMANCE Kullanım kılavuzu
Artículos relacionados
-
ASROCK E3V5 Performance Gaming Manual de usuario
-
-
-
-
ASROCK Fatal1ty Guía de inicio rápido
-
-
-
ASROCK Fatal1ty Manual de usuario
-
ASROCK B450 Pro4 Guía de instalación
-
Otros documentos
-
DeLOCK 89370 Ficha de datos
-
DeLOCK 89381 Ficha de datos
-
TooQ TQE-2200 Manual de usuario
-
NZXT N5 Z690 Manual de usuario
-
OCZ Fatal1ty 550W El manual del propietario
-
TooQ TQE-2201B Manual de usuario
-
Akasa USB 3.0 PCIe card Manual de usuario
-
-
-
OCZ Technology Fatal1ty 750W Especificación