Avanti WCR5404DZD Model WCR5404DZD - Built-In or Free Standing Dual Zone Wine Cooler

Marca: Avanti

Modelo: WCR5404DZD

Categoría: Enfriadores de bebidas

Tipo: Model WCR5404DZD - Built-In or Free Standing Dual Zone Wine Cooler

BUILT-IN DUAL ZONE WINE CHILLER / VINERA CON 2 ZONAS

INSTRUCTION MANUAL

MANUAL DE INSTRUCCIONES

Model Number / No. de Modelo:

WCR5404DZD

(Picture may vary)

BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING

INSTRUCTIONS.

La sección en español empieza en la página 16.

Avanti Products has a policy of continuous improvement on its products and reserves the right to change materials and

specifications without notice.

Avanti Products, A Division of The Mackle Co., Inc.

P.O. Box 520604 - Miami, Florida 33152

www.avantiproducts.com

TABLE OF CONTENTS

Appliance Safety 3

Important Safeguides 4

Help Us Help You … 5

Parts and Features 6

Important Safety Instructions 7

Installation Instructions 7

Before Using Your Wine Chiller 7

Installation of Your Wine Chiller 7

Electrical Connection 8

Extension Cord 8

Reversing the Door Swing of Your Wine Appliance 8

Installing Stainless Steel Handle 9

Operating Your Wine Chiller 9

ON/OFF Power 10

Setting the Temperature Control 10

Storage 11

Interior Light 11

Door Lock 11

Shelves 11

Care and Maintenance 12

Cleaning Your Wine Chiller 12

Power Failure 12

Movin

Your Wine Chille

Energy Saving Tips 12

Troubleshooting Guide 13

Service for Your Appliance 14

Wiring Diagram 14

Your Avanti Products Warranty 15

Instrucciones en Español 16 ~ 18

Registration Information and Registration Card 19

APPLIANCE SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always

read and obey all safety messages.

This is the Safety Alert Symbol. This symbol alerts you to potential hazards that

can kill or injure you and others. All safety messages will follow the Safety

Alert Symbol and either the words “DANGER”, “WARNING” or “CAUTION”.

Danger means that failure to heed this

safety statement may result in severe

personal injury or death.

Warning means that failure to heed this

safety statement may result in extensive

product damage, serious personal injury, or

death.

Caution means that failure to heed this

safety statement may result in minor or

moderate personal injury, or property or

equipment damage.

All safety messages will alert you do what the potential hazard is, tell you how to reduce the chance of

injury, and let you know what can happen if the instructions are not followed.

IMPORTANT SAFEGUIDES

Before the appliance is used, it must be properly positioned and installed as

described in this manual, so read the manual carefully. To reduce the risk of fire,

electrical shock or injury when using the appliance, follow basic precaution,

including the following:

 Plug into a grounded 3-prong outlet, do not remove grounding prong, do not use an adapter, and

do not use an extension cord.

 Replace all panels before operating.

 It is recommended that a separate circuit, serving only your appliance be provided. Use

receptacles that cannot be turned off by a switch or pull chain.

 Never clean appliance parts with flammable fluids. These fumes can create a fire hazard or

explosion. And do not store or use gasoline or other flammable vapors and liquids in the vicinity of

this or any other appliance. The fumes can create a fire hazard or explosion.

 Before proceeding with cleaning and maintenance operations, make sure the power line of the

unit is disconnected.

 Do not connect or disconnect the electric plug when your hands are wet.

 Unplug the appliance or disconnect power before cleaning or servicing. Failure to do so can result

in electrical shock or death.

 Do not attempt to repair or replace any part of your appliance unless it is specifically

recommended in this material. All other servicing should be referred to a qualified technician.

FOLLOW WARNING CALL OUTS BELOW ONLY WHEN APPLICABLE TO YOUR MODEL

 Use two or more people to move and install appliance. Failure to do so can result in back or other

injury.

 To ensure proper ventilation for your appliance, the front of the unit must be completely

unobstructed. Choose a well-ventilated area with temperatures above 60°F (16°C) and below

90°F (32°C). This unit must be installed in an area protected from the element, such as wind, rain,

water spray or drips.

 The appliance should not be located next to ovens, grills or other sources of high heat.

 The appliance must be installed with all electrical connections in accordance with state and local

codes. A standard electrical supply (115 V AC only, 60 Hz), properly grounded in accordance with

the National Electrical Code and local codes and ordinances is required.

 Do not kink or pinch the power supply cord of appliance.

 The fuse (or circuit breaker) size should be 15 amperes.

 It is important for the appliance to be leveled in order to work properly. You may need to make

several adjustments to level it.

 Never allow children to operate, play with or crawl inside the appliance.

 Do not use solvent-based cleaning agents of abrasives on the interior. These cleaners may

damage or discolor the interior.

 Do not use this apparatus for other than its intended purpose.

HELP US HELP YOU...

Read this guide carefully.

It is intended to help you operate and maintain

your new Wine Chiller properly.

Keep it handy to answer your questions.

If you don't understand something or you

need more assistance, please call:

Avanti Customer Service

800-220-5570

Keep proof of original purchase date (such as

your sales slip) with this guide to establish the

warranty period.

Write down the model and serial numbers.

You'll find them on a plate located on the rear

outside wall of the Wine Chiller.

Please write these numbers here:

____________________________________

Date of Purchase

____________________________________

Model Number

____________________________________

Serial Number

Use these numbers in any correspondence or

service calls concerning your Wine Chiller.

If you received a damaged Wine Chiller,

immediately contact the dealer (or builder) that

sold you the Wine Chiller.

Save time and money. Before you call for

service, check the Troubleshooting Guide. It

lists causes of minor operating problems that

you can correct yourself.

IF YOU NEED SERVICE

We're proud of our service and want you to be

pleased. If for some reason you are not happy

with the service you receive, here are some

steps to follow for further assistance.

FIRST, contact the people who serviced your

Wine Chiller. Explain why you are not pleased.

In most cases, this will solve the problem.

NEXT, if you are still not pleased, write all the

details, including your telephone number, and

send it to:

Customer Service

Avanti Products

10880 NW 30 Street

Miami, FL 33172 USA

CAUTION:

THIS WINE CHILLER IS NOT

DESIGNED FOR THE STORAGE

OF MEDICINE OR OTHER

MEDICAL PRODUCTS.

PARTS & FEATURES

1 Control Panel

2 Security Lock

3 Stainless Steel Door Frame

4 Stainless Steel Door Handle

5 Large Shelves (Total 5)

6 Zone Partition

7 Small Bottom Shelf (Total 1)

8 Bottom Grille

9 Leveling Legs (4)

10 Cabinet

IMPORTANT SAFETY INSTRUCTIONS

WARNING

To reduce the risk of fire, electrical shock,

or injury when using your appliance, follow

these basic precautions:

 Read all instructions before using the Wine Chiller.

 DANGER or WARNING: Risk of child entrapment.

Child entrapment and suffocation are not problems of the past. Junked or abandoned

appliances are still dangerous . . . even if they will “just sit in the garage a few days”.

 Before you throw away your old Wine Chiller: Take off the door. Leave the

shelves in place so that children may not easily climb inside.

 Never allow children to operate, play with, or crawl inside the appliance.

 Never clean appliance parts with flammable fluids. The fumes can create a fire

hazard or explosion.

 Do not store or use gasoline or any other flammable vapors and liquids in the vicinity

of this or any other appliance. The fumes can create a fire hazard or explosion.

-Save these instructions-

INSTALLATION INSTRUCTIONS

 BEFORE USING YOUR WINE CHILLER

 Remove the exterior and interior packing. Read the Installer’s Directions.

 Check to be sure you have all of the following parts:

 5 Roll-out Shelves

 1 Small Bottom Shelf

 2 Keys

 1 Stainless Steel Handle Assembly with 2 Screws, 2 Flat Washers and 2 Lock Washers

 1 Door Lower Hinge Bracket for Door Opening from the Right Side

 1 Instruction Manual

 Before connecting the Wine Chiller to the power source, let it stand upright for approximately 2

hours. This will reduce the possibility of a malfunction in the cooling system from handling during

transportation.

 Clean the interior surface with lukewarm water using a soft cloth.

 Install the handle on the left side of the door.

 INSTALLATION OF YOUR WINE CHILLER

 This appliance is designed to be for free standing installation or built-in (fully recessed).

 Place your Wine Chiller on a floor that is strong enough to support it when it is fully loaded. To

level your Wine Chiller, adjust the front leveling legs at the bottom of the Wine Chiller.

 Locate the Wine Chiller away from direct sunlight and sources of heat (stove, heater, radiator,

etc.). Direct sunlight may affect the acrylic coating and heat sources may increase electrical

consumption. Extreme cold ambient temperatures may also cause the unit not to perform

properly.

 Avoid locating the unit in moist areas.

 Plug the Wine Chiller into an exclusive, properly installed-grounded wall outlet. Do not under any

circumstances cut or remove the third (ground) prong from the power cord. Any questions

concerning power and/or grounding should be directed toward a certified electrician or an

authorized Avanti Products service center.

 ELECTRICAL CONNECTION

This appliance should be properly grounded for your safety. The power cord of this appliance is

equipped with a three-prong plug which mates with standard three prong wall outlets to minimize the

possibility of electrical shock.

Do not under any circumstances cut or remove the third ground prong from the power cord supplied.

For personal safety, this appliance must be properly grounded.

This appliance requires a standard 115/120 Volt AC ~/60Hz electrical ground outlet with three-prong.

Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly

grounded. When a standard 2-prong wall outlet is encountered, it is your responsibility and obligation

to have it replaced with a properly grounded 3-prong wall outlet.

The cord should be secured behind the appliance and not left exposed or dangling to prevent

accidental injury.

The appliance should always be plugged into its own individual electrical outlet which has a voltage

rating that matches the rating label on the appliance. This provides the best performance and also

prevent overloading house wiring circuits that could cause a fire hazard from overheated. Never

unplug the appliance by pulling the power cord. Always grip the plug firmly and pull straight out from

the receptacle. Repair or replace immediately all power cords that have become frayed or otherwise

damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.

When moving the appliance, be careful not to damage the power cord.

 EXTENSION CORD

Because of potential safety hazards under certain conditions, it is strongly recommended that you do

not use an extension cord with this appliance. However, if you must use an extension cord it is

absolutely necessary that it be a UL/CUL-Listed, 3-wire grounding type appliance extension cord

having a grounding type plug and outlet and that the electrical rating of the cord be 115 volts and at

least 10 amperes.

 REVERSING THE DOOR SWING OF YOUR APPLIANCE

This appliance has the capability of the door opening from either the left or right side. The unit is

delivered to you with the door opening from the left side. Should you desire to reverse the opening

direction, please call service for reversal instructions.

Warning

Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is

damaged, have it replaced by an authorized Avanti Products service center.

 INSTALLING STAINLESS STEEL HANDLE

This wine chiller includes a stainless steel handle that is not required to operate this unit. To install the

handle please follow the below instructions:

1. Pull away the door gasket in the area where the handle is to be installed on the left side as

shown below in Illustration # 1. The gasket is easily displaced by hand, no tools are

necessary.

2. Using a Flat head screwdriver remove the two (2) pre-installed decorative plugs from the

backside of the door as shown below in Illustration #1. Save the decorative plugs for future

use.

3. Insert the two (2) Phillips head handle screws with the lock washers and flat washers

attached through the gasket side of the door frame until the screws pass through the door

frame. Follow the sequence shown below in Illustration # 2.

4. Align the handle with the screws installed in the above step # 3. Tighten the screws using a

Phillips head screwdriver until the handle sets both flush and secured tightly against the door

frame. (DO NOT overtighten as this will cause damage to the handle assembly).

5. Replace the door gasket to its original position.

 Gasket  Decorative Screw  Phillips Head Screw

 Lock Washer  Flat Washer

 S/S Handle

OPERATING YOUR WINE CHILLER

It is recommended you install the Wine Chiller in a place where the ambient temperature is between

72-78 degrees Fahrenheit. If the ambient temperature is above or below recommended

temperatures, the performance of the unit may be affected. For example, placing your unit in extreme

cold or hot conditions may cause interior temperatures to fluctuate. The range of 40-65 degrees

Fahrenheit may not be reached.

Recommended Temperatures for Chilling Wine.

Red Wines 58-65 F

Dry/White Wines 48-57 F

Rose Wines 49-51 F

Sparkling Wines 40-47 F

 ON/OFF POWER

To turn ON or OFF the appliance, press the

button/mark and hold for 2 seconds.

 Control Panel Lock.

 Your Wine chiller is equipped with an automatic Control panel lock function. This

function will prevent any unwanted changes to your temperature or power settings.

 The lock function will activate automatically 12 seconds after the last time a button is

pushed on the control panel.

 To unlock the control panel lock press and hold the (↑)andthe(↓)buttonsfor3

secondsthecontrolpanelwillbeepandblinkonceindicatingthatthecontrolpanelisactive

andthesettingscanbechanged.

 SETTING THE TEMPERATURE CONTROL

You can press the left side UP and DOWN buttons/marks to control the internal temperature of the

upper zone and press the right side UP and DOWN buttons/marks to control the internal temperature

of the lower zone.

The degrees indicators will appear in the display window marked UPPER ZONE and LOWER ZONE.

The temperature range of LOWER ZONE is 55 ~ 65 ºF which is suitable for storing white and red

wines. The temperature range of UPPER ZONE is 40 ~ 55ºF which is suitable for storing sparkling

and white wines.

 The temperature that you desire to set will increase 1ºF or 1ºC if you push the UP button/mark

once, on the contrary the temperature will decrease 1ºF or 1ºC if you push the DOWN

button/mark once.

 When you store mostly red wines, you should store them in the LOWER ZONE, the temperature

which you control by pushing the above UP and DOWN buttons/marks need to be set at between

58 to 65 F and the red LED lamp under “RED” marking will be lit

 When you store mostly white wines, you can store them in the UPPER ZONE or LOWER ZONE.

When you use the LOWER ZONE, the temperature can be set at between 55 to 57 F and the

green LED lamp under “WHITE” marking will be lit. When you use the UPPER ZONE, the

temperature can be set at between 48 to 55 F and the green LED lamp under “WHITE” marking

will be lit.

 When you store mostly sparkling wines, you should store them in the UPPER ZONE, the

temperature needs to be set at between 40 to 47 F and the yellow LED lamp under “SPARKL”

marking will be lit.

NOTE:

 If the unit is unplugged, power lost, or turned off, you must wait 3 to 5 minutes before restarting

the unit. If you attempt to restart before this time delay, the Wine Chiller will not start.

 When you use the wine chiller for the first time or restart the wine chiller after having been shut off

The LED readout will show the original temperature set previously (the preset temperature at the

factory for UPPER ZONE is 50ºF and for LOWER ZONE is 60ºF).

You can select temperature display setting from Fahrenheit to Celsius degree by pushing the ºF/ºC

button/mark. Fahrenheit or Celsius degrees indicator will appear in blue color in the temperature

display window for each zone.

for a long time, there could be a few degrees variance between the temperature you select and

the one indicated on the LED readout. This is normal and it is due to the length of the activation

time. Once the wine chiller is running for a few hours everything will be back to normal.

 STORAGE

Many bottles may differ in size and dimensions. As such the actual number of bottles you may be able

to store may vary.

NOTE: You can place 16 standard bottles in the upper zone and 30 standard bottles in the lower

zone.

Bottle capacities are approximate maximums when storing traditional Bordeaux 750 ML bottles and

include bulk storage.

 INTERIOR LIGHT

 Interior lights are available in both upper and lower zones.

 You can turn the interior light on in each zone by pushing the button marked with the “bulb”

symbol

or touch the mark .

 The lights will turn off automatically if it remains ON for 10 minutes or more. You have to push the

button marked with the “bulb” symbol

or touch the mark again and the light will turn

back on.

 DOOR LOCK

Your unit is provided with a lock and key combination.

The keys are located inside the plastic bag that contains the User’s Guide. Insert the key into the lock

and turn it counterclockwise to unlock the door. To lock the door do the reverse operation making

sure metal pin is engaged completely. Remove the key and place it in a secure place for safekeeping.

 SHELVES

This appliance is equipped with a pull-out roller assembly (except for the bottom shelf) and you can

move the wooden shelves out and in smoothly.

Pull-out Roller Shelves (Total 5)

 To prevent damaging the door gasket, make sure to have the door all the way opened when

pulling shelves out of the rail compartment.

 For easy access to the bottles, you must pull the shelves approximately 1/3 out of the rail

compartment.

 To remove the shelves out of the rail pull each shelf approximately 1/3 out. Use a long flat

screwdriver to press down the right plastic notch as shown in Figure A and at the same time lift

the left plastic notch as shown in Figure B. Then proceed to pull out the shelf slowly. Contact our

service department if assistance is needed.

Figure A Figure B

CARE AND MAINTENANCE

 CLEANING YOUR WINE CHILLER

 Turn off the power, unplug the appliance, and remove all items including shelves.

 Wash the inside surfaces with a warm water and baking soda solution. The solution should be

about 2 tablespoons of baking soda to a quart of water.

 Wash the shelves with a mild detergent solution.

 Wring excess water out of the sponge or cloth when cleaning area of the controls, or any

electrical parts.

 Wash the outside cabinet with warm water and mild liquid detergent. Rinse well and wipe dry with

a clean soft cloth.

 Do not use steel wool or steel brush on the stainless steel. These will contaminate the stainless

steel with steel particles and rusting may occur.

 POWER FAILURE

 Most power failures are corrected within a few hours and should not affect the temperature of

your appliance if you minimize the number of times the door is opened. If the power is going to be

off for a longer period of time, you need to take the proper steps to protect your contents.

 MOVING YOUR WINE CHILLER

 Remove all items.

 Securely tape down all loose items (shelves) inside your appliance.

 Turn the adjustable legs up to the base to avoid damage.

 Tape the door shut.

 Be sure the appliance stays secure in the upright position during transportation. Also protect

outside of appliance with a blanket, or similar item.

 ENERGY SAVING TIPS

 The Wine Chiller should be located in the coolest area of the room, away from heat producing

appliances, and out of the direct sunlight.

PROBLEMS WITH YOUR WINE CHILLER?

You can solve many common Wine Chiller problems easily, saving you the cost of a possible service

call. Try the suggestions below to see if you can solve the problem before calling the servicer.

TROUBLESHOOTING GUIDE

PROBLEM POSSIBLE CAUSE

Wine Chiller does not operate.

Not plugged in.

The appliance is turned off.

The circuit breaker tripped or a blown fuse.

Wine Chiller is not cold enough. Check the temperature control setting.

External environment may require a higher

setting.

The door is opened too often.

The door is not closed completely.

The door gasket does not seal properly.

Turns on and off frequently. The room temperature is hotter than normal.

A large amount of contents has been added to

the wine chiller.

The door is opened too often.

The door is not closed completely.

The temperature control is not set correctly.

The door gasket does not seal properly.

The light does not work.

Not plugged in.

The circuit breaker tripped or a blown fuse.

The light button is “OFF”.

Vibrations. Check to assure that the Wine Chiller is level.

The Wine Chiller seems to make too much noise.

The rattling noise may come from the flow of the

refrigerant, which is normal.

As each cycle ends, you may hear gurgling

sounds caused by the flow of refrigerant in your

Wine Chiller.

Contraction and expansion of the inside walls

may cause popping and crackling noises.

The Wine Chiller is not level.

The door will not close properly.

The Wine Chiller is not level.

The door was reversed and not properly installed.

The gasket is dirty.

The shelves are out of position.

SERVICE FOR YOUR WINE CHILLER

We are proud of our customer service organization and the network of professional service

technicians that provide service on your Avanti appliances. With the purchase of your Avanti

appliance, you can have the confidence that if you ever need additional information or assistance, the

Avanti Products Customer Service team will be here for you. Just call us toll-free.

AVANTI PRODUCTS CUSTOMER SERVICES

Product Information

800-323-5029

Whatever your questions are about our products,

help is available.

Part Orders

800-220-5570

You may order parts and accessories that will be

delivered directly to your home by personal

check, money order, Master Card, or Visa.

In-Home Repair Service

800-220-5570

An Avanti Products authorized service center will

provide expert repair service, scheduled at a time

that is convenient for you. Our trained servicers

know your appliance inside and out.

WIRING DIAGRAM

YOUR Avanti Products WARRANTY Staple your sales receipt here. Proof of

original purchase date is needed to obtain

service under warranty.

WHAT IS COVERED

LIMITED ONE-YEAR

WARRANTY

For one year from the date of

purchase by the original owner, Avanti

Products will, at its option, repair or

replace any part of the unit, which

proves to be defective in material or

workmanship under normal use.

During this period Avanti Products will

provide all parts and labor necessary

to correct such defects free of charge,

so long as the unit has been installed

and operated in accordance with the

written instructions in this manual.

Avanti Products will provide you with a

reasonably similar replacement

product that is either new or factory

refurbished. In rental or commercial

use, the warranty period is 90 days.

All Avanti Appliances of 3.5 cubic feet

capacity or less must be brought/sent

to the appliance service shop for

repair.

 Content losses of food or other, due to

spoilage.

 Incidental or consequential damages.

 Parts and labor costs for the following will

not be considered as warranty:

 Door springs, and/or frames.

 Inner door panels, door rails and/or door

supports.

 Light bulbs and/or plastic housing.

 Plastic cabinet liners.

 Punctured evaporator that voids the

warranty on the complete sealed system.

 Repairs performed by unauthorized

servicers.

 Shipping and handling costs associated

with the replacement of the unit.

LIMITED SECOND THROUGH

FIFTH YEAR WARRANTY

For the second through the fifth year from date

of original purchase, Avanti Products will

provide a replacement compressor free of

charge due to a failure. You are responsible

for the service labor and freight charges. In

rental or commercial use, the limited

compressor warranty is one year and nine

months. Cost to move the appliance to the

servicers’ shop and back to the user's home,

as may be required, are the user's

responsibility.

 Service calls that do not involve defects in

material or workmanship such as

customer education, door reversal, or

proper installation.

 Service calls that are related to external

problems, such as abuse, misuse,

inadequate electrical power, accidents,

fire, floods, or acts of God.

 Surcharges including, but not limited to,

any after hour, weekend, or holiday

service calls, tolls, ferry trip charges, or

mileage expenses for service calls to

remote areas, including the State of

Alaska.

 Replacement of house fuses or resetting

circuit breakers.

 Failure of the product if it is used for other

than its intended purpose.

 This warranty does not apply outside the

Continental USA.

WHAT IS NOT COVERED

INSTRUCCIONES DE SEGURIDAD

ATENCION

INSTRUCCIONES PARA

LA CONEXION A TIERRA

Este aparato electrodoméstico debe estar conectado a tierra. En caso de un cortocircuito eléctrico, la

conexión a tierra reduce el riesgo de choque eléctrico proporcionando un cable a tierra con una

enchufe de conexión a tierra. Este enchufe debe estar conectado en un tomacorriente instalado

correctamente y conectado a tierra.

ADVERTENCIA – El uso inadecuado del enchufe de conexión a tierra puede resultar en un riesgo de

choque eléctrico. Consulte con un electricista o persona de reparaciones competente si no

comprenden bien las instrucciones de conexión a tierra o si existe alguna duda sobre si el aparato

esta conectado a tierra correctamente.

NO USE UN CORDON DE

PROLONGACION ELECTRICA

Use un tomacorriente de pared exclusivo. No conecte su vinera a cordones de prolongación eléctrica

o junto a cualquier otro electrodoméstico en el mismo tomacorriente de pared.

ADVERTENCIA IMPORTANTE:

Una vinera vacía es una atracción muy peligrosa para los niños. Saque todas las juntas,

pestillos, tapas o puerta de todo electrodoméstico que no esté en uso, o tome alguna

medida para asegurar que no presente peligro.

INSTRUCCIONES DE INSTALACION

Saque los embalajes exteriores, limpie bien el exterior con un paño suave seco, y el interior con un

paño húmedo y tibio. Evite colocar la vinera cerca de una fuente de calor, luz de sol directa, o lugar

húmedo.

UBICACION

1. Seleccione un lugar con su piso fuerte y nivelado.

2. Evite la luz directa del sol o calor. La luz directa del sol puede afectar la capa de acrílico.

Las fuentes de calor en su proximidad provocarán un consumo mayor de electricidad.

OPERACION

Para evitar vibraciones, el compartimiento interior debe estar bien nivelado. La temperatura variará

dependiendo de la cantidad de botellas almacenadas y la frecuencia con que se abre la puerta.

Cuando la vinera no se use por un período largo, desconecte el enchufe y deje la puerta entreabierta.

Nota: Espere entre 3 a 5 minutos antes de volver a encender si el funcionamiento ha sido

interrumpido.

Se recomienda que Ud coloque su vinera en un lugar donde la temperatura ambiental se mantenga

entre 23-25 grados centígrados.

Si la temperatura ambiental oscila afuera de esos límites, pueda afectar la temperatura de la caja.

Por ejemplo, si su unidad está situada en lugares donde hay temperaturas muy frías o calientes

también puede afectar la temperatura de la caja.

Temperaturas recomendadas para enfriar vinos:

Vinos tintos: 58 - 65ºF (14-18ºC)

Vinos blanco/seco: 48 - 57ºF (9-14ºC)

Vinos rosé/Zinfandel:

49 - 51ºF (9-11ºC)

Vinos blanco/espumante: 40 - 47ºF (4- 8ºC)

ENCENDIDO/APAGADO

Para apagar el refrigerador de vino, presione el botón (

) y manténgalo presionado por un mínimo

de 3 segundos.

PANEL DE CONTROL DE SEGURIDAD

 Su refrigeradora de vino está equipada con un Panel de Control de Seguridad de función

automática. Esta función previene cualquier cambio no deseado en el control de

temperatura.

 La función de seguridad se activara automáticamente 12 segundos después de la última vez

que cualquier botón del Panel de Control sea presionado.

 Para poder hacer cambios en el Panel de Control, presione y mantenga presionados los

botones (

↑ ) y (↓ ) por 3 segundos, el Panel del Control emitirá un sonido de “Beep” y

parpadeara una vez, indicando que el Panel de Control ha sido activado y que puede

efectuar cambios en los controles.

OPERACION

Oprima los botones marcado “

“ y “ “ localizados en el lado izquierdo del panel de

controles para programar la temperatura interna de la zona superior. Repita esa operación pero con

los botones localizados en el lado derecho para programar la temperatura interna de la zona inferior.

La pantalla mostrará los grados respectivamente para cada zona en color rojo. La temperatura en la

zona inferior varia entre 55~65ºF (13~18ºC) y es la indicada para los vinos rojos o blancos.

La temperatura en la zona superior varia entre 40~55ºF (5~13ºC) y es la indicada para los vinos

blancos o espumosos.

Al presionar los botones marcados “

“ o “ “ por primera vez, el indicador en la pantalla

mostrará la temperatura programada de fábrica o la más reciente.

Oprima el botón marcado (

) una vez y la temperatura aumentará un grado. Si Ud oprime el

botón marcado (

) una vez la temperatura bajará un grado.

Si en su mayoría Usted solamente guarda vinos rojos, debe colocarlos en la zona inferior.

El indicador marcado (RED) se alumbrará en color rojo. Ud necesita programar esa temperatura

entre los 58~65ºF (15~18ºC).

Si Ud solamente guarda vinos blancos, usted puede colocarlos en cualquier zona pero tendrá que

mantener una temperatura entre 55~57ºF (13~14ºC) en la zona inferior y una temperatura de

48~55ºF (9~13ºC) en la zona superior.

El indicador marcado “WHITE” se alumbrará en color verde.

Cuando Ud guarda vinos espumosos, deberá colocar las botellas en la zona superior y marcar la

temperatura entre los 40~47ºF (5~8ºC).

El indicador marcado “SPARKL” se alumbrará en color amarillo.

En la fábrica se programa la zona superior a los 50ºF (10ºC).

La zona inferior se programa a los 60ºF (16ºC).

Ud puede cambiar de grados Centígrados a Fahrenheit o viceversa, oprimiendo el boton marcado

ºF/C. En la pantalla digital para cada zona aparecerán los grados en color azul.

LUZ INTERIOR

La luz interior para cada zona se controla manualmente y no funciona al abrir ni cerrar la puerta.

Para prender o apagár la luz, presione el botón marcado (

) de la luz ubicado en el panel de

control. Si la luz está prendida, por más de 10 minutos, se apagará automáticamente.

CERRADURA DE LA PUERTA

Su unidad viene equipada con una combinación de cerradura y llave.

Las llaves (2) están dentro de la bolsa plástica junto al manual de instrucciones.

Introduzca la llave en la cerradura y gírela hacia la izquierda para abrir la puerta.

Para cerrarla, gire la llave hacia la derecha.

Quite la llave y colóquela en un lugar seguro para evitar que se pierda.

COMO INSTALAR LA MANIJA

Su nevera viene equipada con una manija de acero inoxidable que no es necesario instalar

para operar la unidad.

Para instalarla, remueva los tornillos decorativos del frente de la puerta.

Coloque la manija en su lugar designado utilizando los tornillos Phillips incluídos en la bolsa.

Apriete los tornillos utilizando un destornillador Phillips (+).

DESCONGELACION

Su refrigerador para vinos ha sido diseñado con un sistema de descongelación de “ciclo automático”.

Las superficies refrigeradas del compartimiento para vinos se descongela automáticamente, durante

el ciclo “apagado” del control de enfriamiento (termostato). El agua descongelada del compartimiento

es eliminada automáticamente, encauzándola hacia una bandeja de goteo ubicado en el compresor.

La transferencia de calor del compresor evapora el agua.

ADVERTENCIA

Asegúrese de tener la puerta abierta completamente se Ud desea remover los estantes de madera o

moverlos hacia adelante para extraer una botella.

NOTA:

Para remover los estantes de madera corredizos, mueva cada uno de ellos aproximadamente una

tercera parte fuera de los raíles.

Presione el lado plástico derecho usando un destornillador plano (siga la flecha) como se muestra en

el dibujo “A” de la página 14 y a la misma vez haga lo mismo con el plástico del lado izquierdo como

se muestra en el dibujo “B” de la página 14.

Saque el estante corredizo suavemente.

CUIDADO Y MANTENIMIENTO

LIMPIEZA

Para limpiar el interior, use un paño suave con una solución de una cucharada de bicarbonato de

sodio por cada cuarto de agua, o una solución de espuma de jabón suave, o un detergente suave.

Para lavar las rejillas, sáquelas deslizándolas con cuidado, y use una solución de detergente suave;

luego séquelas con un paño suave. Limpie el exterior con un paño húmedo suave y un poco de

detergente suave o productos de limpieza para electrodomésticos.

CORTE DE CORRIENTE

La mayoría de los cortes de corriente se corrigen en una o dos horas y no afectarán las temperaturas

de su vinera. Sin embargo, Ud. deberá reducir la cantidad de veces que abra la puerta cuando la

corriente esté apagada.

SI UD. SE MUDA

Saque o asegure todos los artículos dentro de su vinera. Para evitar que los tornillos nivelantes se

averíen, gírelos completamente hacia la base.

REGISTRATION INFORMATION

Thank you for purchasing this fine Avanti products. Please fill out this form and return it within 100

days of purchase and receive these important benefits to the following address:

Avanti Products, A Division of The Mackle Co., Inc.

P.O. Box 520604 - Miami, Florida 33152 USA

 Protect your product:

We will keep the model number and date of purchase of your new Avanti Products product on

file to help you refer to this information in the event of an insurance claim such as fire or theft.

 Promote better products:

We value your input. Your responses will help us develop products designed to best meet

your future needs.

----------------------------------------------------------(detach here)----------------------------------------------------------

Avanti Registration Form

__________________________________ _____________________________________

Name Model # Serial #

__________________________________ _____________________________________

Address Date Purchased Store/Dealer Name

__________________________________ ______________________________________

City State Zip Occupation

__________________________________ As Your Primary Residence, Do You:

Area Code Phone Number Own Rent

Did You Purchase An Additional Warranty:

Your Age:

Extended Food Loss None under 18 18-25 26-30

Reason For Choosing This Avanti Product: 31-35 36-50 over 50

Please indicate the most important factors Marital Status:

that influenced your decision to purchase Married Single

this product. Is This Product Used In The:

Price Home Business

Product Features How Did You Learn About This Product:

Avanti Products Reputation Advertising

Product Quality In Store Demo Personal Demo

Salesperson Recommendation Other_______________________________

Friend/Relative Recommendation Comments____________________________

Warranty _____________________________________

Other_______________________ _____________________________________

PRINTED IN CHINA

Avanti WCR5404DZD Model WCR5404DZD - Built-In or Free Standing Dual Zone Wine Cooler

Marca: Avanti

Modelo: WCR5404DZD

Categoría: Enfriadores de bebidas

Tipo: Model WCR5404DZD - Built-In or Free Standing Dual Zone Wine Cooler

Descargar PDF

informe

en otros idiomas

English: Avanti WCR5404DZD

Avanti WCR5404DZD Model WCR5404DZD - Built-In or Free Standing Dual Zone Wine Cooler

Avanti WCR5404DZD Model WCR5404DZD - Built-In or Free Standing Dual Zone Wine Cooler

en otros idiomas

Artículos relacionados

Otros documentos