Swann ALPHA Manual de usuario

Marca: Swann

Modelo: ALPHA

Tipo: Manual de usuario

Wireless

Motion Sensor

3-Head Spotlight

with Remote Control

Instruction Manual

1200 Lumens

LED Light Panels

Power OFF.

The spotlight will switch back to

auto mode after 1 hour if no other

button is pressed

Set LED Light to stay OFF

when motion is detected

Set Enforcer Lights to stay OFF

when motion is detected

Set motion sensor sensitivity to

Low. Detection range is up to

10ft/3m

Set motion sensor sensitivity

to Medium. Detection range is

up to 13ft/4m

Override sensor and manually

turn LED Light ON for an indenite

amount of time until you press the

Power OFF button

Infrared (IR) signal transmitter

Set LED Light to automatically turn

ON when motion is detected.

LED Light will turn off 20 seconds

after no motion is detected

Set Enforcer Lights to automatically

turn ON when motion is detected.

Enforcer Lights will turn off 20

seconds after no motion is detected

Set motion sensor sensitivity to

High. Detection range is up to

20ft/6m

Override sensor and manually

turn LED Light ON for 10 minutes.

(after 10 minutes the LED Light

will turn off and operate in auto

mode)

Blue Enforcer Flashing

LED Light

Light Sensor

Passive Infrared

Motion Sensor

The ambient light sensor prevents the

spotlight from automatically activating

during the daytime to preserve battery life.

Keeping the LED Light on continuously for prolonged periods

of time will signicantly shorten battery lifespan and reduce

operating time.

Spotlight

Remote Control

OVERVIEW

Red Enforcer Flashing

LED Light

Spotlight

The spotlight requires four D size batteries (not supplied). For reliable, long-lasting

performance, use only high quality alkaline batteries. To install batteries (see Figure 1):

Remote Control

1. Unscrew the battery compartment cover on the rear of the spotlight with a small

Philips screwdriver and lift it off.

2. Insert batteries according to the polarity markings (+ and -) indicated inside the

battery compartment.

3. Replace the battery compartment cover and screw it back into place with the

previously removed screws.

Figure 1

Figure 2

CR2025

PUSH

Locking Screw

BATTERY INSTALLATION

The remote control is powered by a CR2025 battery which comes pre-installed.

• To activate the battery, simply pull the plastic lm out from the bottom of the

remote control.

• To replace the battery, remove the locking screw on the back of the remote control

using a small Phillips screwdriver, then push the tab on the left of the battery tray

towards the right and pull out the battery tray from the remote control (see Figure

2). Place a new "CR2025" battery on the tray with the positive (+) side facing up.

Insert the tray back into the remote control and secure with the locking screw.

WARNING! This product contains a button/coin cell battery. If the button/coin cell battery is swallowed,

it can cause internal chemical burns in as little as two hours and lead to death. Dispose of used

batteries immediately. Keep new and used batteries away from children. If the battery compartment

does not close securely, stop using the product. If you think batteries might have been swallowed or

placed inside any part of the body, seek immediate medical attention.

Australia: If you think batteries might have been swallowed or placed inside any part of the body,

immediately call the 24-hour Poisons Information Centre on 13 11 26 for fast, expert advice and go

straight to the nearest hospital emergency room.

USING THE REMOTE CONTROL

PAIRING WITH THE INDOOR ALARM RECEIVER

• Point the remote control in the direction of the spotlight to operate it. Ensure the

distance is within 5 meters/16 ft and there is no obstruction between the remote

control and the spotlight.

• If you have more than one spotlight unit in the vicinity, the remote control should be

pointed, as close as possible, to the spotlight you want to operate. This will prevent

other spotlights from receiving unwanted IR signals. IR signals emitted by the

remote control may interfere with the operation of other nearby electronic devices.

• When pressing any button on the remote control, the spotlight will ash the Red

Enforcer LED light once to conrm it has received the command.

• If you set both "Light on Motion" and "Enforcer on Motion" to , the spotlight will

temporarily stop detecting motion for 1 hour. After 1 hour, the spotlight will revert to

automatic mode (i.e., spotlight will activate when motion is detected). You can re-

enable the motion sensor at any time by pressing the "Light on Motion" button.

• If you want the spotlight to activate only the red and blue Enforcer lights when

motion is detected, perform the steps below in the following order:

1. Press the "Light on Motion" button.

2. Press the "Enforcer on Motion" button.

3. Press the "Light on Motion" button.

1. Turn the front cover of the spotlight counter-clockwise to the unlock position

(see Figure 1 on previous page) so it is no longer powered. Leave the batteries

inside the battery compartment.

2. Decide which Sensor Channel (1, 2 or 3) you want to

assign to the spotlight, then press and hold the desired

Sensor Channel Number button on the side of the

Indoor Alarm Receiver until the corresponding Sensor

Channel LED indicator lights up and a beep is heard.

The Indoor Alarm Receiver is now in pairing mode.

3. Within 25 seconds, power up the spotlight by turning

the front cover clockwise to the lock position to secure the battery compartment

(see Figure 3 on previous page). The Sensor Channel melody sounds with the

corresponding Sensor Channel LED indicator blinking on the Indoor Alarm Receiver

to conrm successful pairing.

4. If pairing is not completed within 25 seconds, the Sensor Channel LED indicator

goes off and the Indoor Alarm Receiver is no longer in pairing mode. Repeat steps

above to pair the spotlight again.

TIP: For more information on operating the Indoor Alarm Receiver such as adjusting the

volume, refer to the instruction manual that came with your alarm system.

You can pair the spotlight with your existing Indoor Alarm Receiver to get sound alerts

when motion is detected.

Doorbell

Channel Button

Sensor Channel

1, 2, 3 Buttons

• The spotlight can be deployed outdoors, for example near the entry to your

driveway or garage, or mount it near a likely access point such as the front door/

entrance to your home or business.

• For optimal coverage, mount the spotlight approximately 2 meters/6.5 ft above the

ground, pointing slightly downwards at an angle where the most likely approach

path of visitors and vehicles is across the front of the spotlight. Motion detection

is less effective when movement is directly towards or away from the front of the

spotlight (see Figure 3).

• You can adjust the detection range of the spotlight using the Motion Sensitivity

- Low/Med/High buttons on the remote control. In general, the higher the Motion

Sensitivity setting, the greater the possibility of false triggering. To reduce false

triggering, choose a lower Motion Sensitivity setting.

MOUNTING THE SPOTLIGHT

To mount the spotlight:

1. Attach the mounting plate to the mounting surface using the supplied screws

(see Figure 4). If mounting on drywall/masonry, install wall anchors rst.

2. Align the slots on the rear of the spotlight with the tabs on the mounting bracket

then press and slide down into the bracket until it locks into place.

3. Adjust the angle and direction of the LED light panels as desired (see Figure 5).

More sensitive Less sensitive

Figure 4 Figure 5

Figure 3

20ft / 6m

LIMITED WARRANTY TERMS & CONDITIONS

Swann Communications warrants this product against defects in workmanship and

material for a period of one (1) year from its original purchase date. You must present

your receipt as proof of date of purchase for warranty validation. Any unit which proves

defective during the stated period will be repaired without charge for parts or labour or

replaced at the sole discretion of Swann. The end user is responsible for all freight charges

incurred to send the product to Swann’s repair centres. The end user is responsible for

all shipping costs incurred when shipping from and to any country other than the country

of origin.

The warranty does not cover any incidental, accidental or consequential damages arising

from the use of or the inability to use this product. Any costs associated with the tting

or removal of this product by a tradesman or other person or any other costs associated

with its use are the responsibility of the end user. This warranty applies to the original

purchaser of the product only and is not transferable to any third party. Unauthorized end

user or third party modications to any component or evidence of misuse or abuse of the

device will render all warranties void.

By law some countries do not allow limitations on certain exclusions in this warranty.

Where applicable by local laws, regulations and legal rights will take precedence.

Have Questions?

We are here to help! Visit us at

http://support.swann.com. You can also email us at

any time via: [email protected]

FCC Statement

This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Battery Safety Information

• Install only new batteries of the same type in your product.

• Failure to insert batteries in the correct polarity, as indicated in the battery compartment, may shorten the life of

the batteries or cause batteries to leak.

• Do not mix old and new batteries.

• Do not mix alkaline, standard (Carbon-Zinc), rechargeable (Nickel Cadmium/Nickel Metal Hydride) or lithium

batteries.

• Batteries should be recycled or disposed of as per state and local guidelines.

Declaración de la FCC

Este equipo se puso a prueba y se determinó que cumple con los límites de dispositivos digitales de Clase B, de

conformidad con la Parte 15 de las Normas de la FCC. Estos límites están diseñados para proporcionar una protección

razonable contra la interferencia dañina en las instalaciones residenciales. Este equipo genera, utiliza y puede irradiar

energía de radiofrecuencia y, en caso de no instalarse correctamente o de no usarse de acuerdo con las instrucciones,

podría causar interferencias dañinas en las radiocomunicaciones. No obstante, no se garantiza que no vayan a existir

interferencias en una instalación particular. Si el equipo causara una interferencia dañina para la recepción de radio o

televisión, que podrá determinarse mediante el apagado y encendido del equipo, se le recomienda al usuario intentar

corregir la interferencia con una o más de las siguientes medidas:

• Reorientar o ubicar en otro lado la antena receptora.

• Aumentar la separación entre el equipo y el receptor.

• Conectar el equipo a un tomacorriente de un circuito distinto al que está conectado el receptor.

• Consultar al distribuidor o a un técnico experimentado en radio/televisión para obtener asistencia.

Información de seguridad de la batería

• Instale solo baterías nuevas del mismo tipo en su producto.

• No colocar las baterías en la polaridad correcta, como se indica en el compartimiento de baterías, puede acortar

la vida de las baterías o producir ltraciones.

• No mezcle baterías nuevas con usadas.

• No mezcle baterías alcalinas, estándares (carbono-cinc), recargables (níquel-cadmio/hidruro de níquel metal) o

baterías de litio.

• Las baterías se deben reciclar o desechar según las directrices estatales y locales.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference,

and

(2) This device must accept any interference

received, including interference that may cause

undesired operation.

This device complies with Industry Canada

licence-exempt RSS standard(S).

Operation is subject to the following two conditions：

(1) this device may not cause interference, and

(2) this device must accept any interference, includ-

ing interference that may cause

undesired operation of the device.

Le présent apparel est conforme aux CNR. d'indus-

trie Canada applicables aux

apparels radioexempts de licence. L'exploitation est

autorisée aux deux conditions

suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de 'appareil doit accepter tout brouil-

lage radioélectrique subl, même

si le brouillage est susceptible d'en compromettre le

fonctionnement.

Swann ALPHA Manual de usuario

Marca: Swann

Modelo: ALPHA

Tipo: Manual de usuario

Descargar PDF

informe

En otros idiomas

English: Swann ALPHA User manual

Documentos relacionados

Swann SWIFI-SPOTCAM Manual de usuario

Swann ALPHA Manual de usuario

Swann ALPHA Manual de usuario

En otros idiomas

Documentos relacionados

Otros documentos