Intelligent Home Aiphone JO Manual de usuario
- Tipo
- Manual de usuario
JOS-1A
JO-DVF
JO-1MD
JOS-1V
JOS-1F
JO-DV
JO-DA
VIDEO DOOR STATION
MASTER MONITOR STATION
VIDEO DOOR STATION
VIDEO DOOR STATION
T hank y ou f or selecting A iphone f or y our com m unication and security needs. P lease read this m anual caref ully f or proper sy stem
operation. For f uture ref erence, k eep m anual in a saf e place.
INSTALLATION & OPERATION MANUAL
MANUEL D’INSTALLATION ET D’UTILISATION
MANUAL DE INSTALACIÓN Y OPERACIÓN
INSTALLATIE- EN BEDIENINGSHANDLEIDING
MANUALE D'INSTALLAZIONE E USO
INSTALLATIONS- UND BEDIENUNGSANLEITUNGHANDBUCH
FK1899 A P0713KD 55060
HANDS-FREE COLOR VIDEO INTERCOM
INTERPHONE VIDEO COULEUR MAINS LIBRES
INTERCOMUNICACIÓN CON VÍDEO A COLOR MANOS LIBRES
HANDENVRIJE KLEURENVIDEOFONIE
VIDEOCITOFONO A COLORI A VIVAVOCE
FREISPRECH-FARBVIDEO-SPRECHANLAGEN-HAUPTSTELLE
JOS-1A, JOS-1V, JOS-1F
EnglishFrançaisEspañolNederlandsItalianoDeutsch
2
PRECAUTIONS
P rohib ited Do not dism antle unit K eep unit aw ay f rom w ater G eneral precautions
WARNING
Negligence could result in death or serious injury.
1. Do not dismantle or alter the unit. Fire or electric shock could result.
2. Keep the unit away from water or any other liquid.
Fire or electric shock could result.
3. High voltage is present internally. Do not open the case.
Electric shock could result.
4. Do not connect any non-specied power source to the +, - terminals.
Also, do not install two power supplies in parallel to a single input.
Fire or damage to the unit could result.
5. Do not use power supply with a voltage other than specied.
Fire or electric shock could result.
6. Do not put any metal or ammable material into the unit through the openings.
Fire, electric shock, or unit trouble could result.
7. The unit must be installed and wired by a qualied technician.
CAUTION
Negligence could result in injury or damage to property.
1. Do not install or make any wire terminations while power supply is plugged in. It
can cause electrical shock or damage to the unit.
2. When mounting the unit on a wall, install the unit in a convenient location, but not
where it could be jarred or bumped. Injury could result.
3. Before turning on power, make sure wires are not crossed or shorted. Fire or
electric shock could result.
4. Do not install the unit in locations subject to frequent vibration or impact. It may
fall or tip over, resulting in damage to the unit or personal injury.
5. For power supply, use Aiphone power supply model specied for use with system.
If non-specied product is used, re or malfunction could result.
6. Do not put anything on the unit or cover the unit with cloth, etc.
Fire or unit trouble could result.
7. Do not install the unit in any of the following locations.
Fire, electric shock, or unit trouble could result.
* Places under direct sunlight or near heating equipment that varies in temperature.
* Places subject to dust, oil, chemicals, hydrogen sulde (hot spring).
* Places subject to moisture and humidity extremes, such as bathrooms, cellars,
greenhouses, etc.
* Places where the temperature is quite low, such as inside a refrigerated area or
in front of an air conditioner.
* Places subject to steam or smoke (near heating or cooking surfaces).
* Where noise generating devices such as dimmer switches or inverter electrical
appliances are closeby.
* Locations subject to frequent vibration or impact.
8. Do not apply high pressure on the screen. If fractured, injury could result.
9. If the LCD is punctured, do not allow skin contact with the liquid crystal inside.
Inammation could result.
* If liquid crystal is ingested, immediately gargle with water and seek medical
attention.
* If contact with the eyes or skin occurs, clean with pure water and seek medical
attention.
GENERAL PRECAUTIONS
1. Keep the unit more than 1m (3.3') away from radio or TV set.
2. Keep the intercom wires more than 30cm (12'') away from AC 100-240V wiring. AC
induced noise and/or unit malfunction could result.
3. Comply with all third party manufacturing specications that will be used with this
system (sensors, door releases, etc.).
4. If the unit is down or does not operate properly, unplug the power supply.
5. When wall-mounted, the top of the unit may darken. This does not indicate a
malfunction.
6. The unit case may become warm with use, but this is not a unit malfunction.
7. If the unit is used near a cellular phone, the unit may malfunction.
8. The unit can be damaged if dropped. Handle with care.
9. The unit will not work during power failure.
10. In areas where broadcasting station antennas are close by, the intercom system may be
affected by radio frequency interference.
11. All the units, except for door stations, are designed for indoor use only.
Do not use at outdoor locations.
12. This product, providing door release, should not be used as a crime prevention device.
13. Please note the LCD panel, though manufactured with very high precision techniques,
inevitably will have a very small portion of its image elements always lit or not lit at
all. This is not considered a unit malfunction.
14. Environmental sound around the unit may hinder smooth communication, but this is
not a malfunction.
15. At night, due to reduced lighting on the object, the screen sees more noise and faces
become more difcult to see, but this is not a malfunction.
16. For hands-free communication:
If you stand too far away, it may be difcult for the other person to hear the
communication.
17. If there are loud noises around the unit (such as music playing or children crying), the
sound may break up and be difcult to hear.
18. During communication, if you speak before the other person has nished talking, your
voice may not come through clearly.
Communication will proceed smoothly if you wait until the other person has nished
before speaking.
19. At a gate or porch illuminated by a uorescent lamp, the image may vary, but this is
not a malfunction.
20. The outline of video images displayed by the video door station may differ from that
of the actual person(s) or background, but this is not a malfunction.
21. If the surface of a video door station freezes during wintertime, the image may
become difcult to see or the call button may not move, but this is not a malfunction.
22. Warm-color lighting shining on the video door station may change the tint of the
image on the screen.
23. When outside temperature lowers sharply after rainfall, etc., the inside of the camera
may fog up slightly, causing a blurry images, but this is not a malfunction. Normal
operation will be restored when moisture evaporates.
24. When the unit’s screen is illuminated with strong light, the image looks white or
silhouetted, but this is not a malfunction.
NOTICES
* We will under no conditions be liable for damage occurring due to the inability to
communicate due to malfunctions, problems, or operational errors in this product.
* We will under no conditions be liable for any damages or losses resulting from this
product’s contents or specications.
* This manual was created by Aiphone Co., Ltd., all rights reserved. Copying, in part
or in whole, this manual without prior permission from Aiphone Co., Ltd. is strictly
forbidden.
* Please note that images and illustrations depicted in this manual may differ from the
actual ones.
* Please note that this manual may be revised or changed without prior notice.
* Please note that product specications may be changed for the sake of improvement
without prior notice.
* This system is not intended for life support or crime prevention. It is a supplementary
means of conveying information. Aiphone will under no conditions be liable for loss of
life or property which occurs while the system is being operated.
* Lighting adjustments are made automatically by the door station. Adjustment results
may vary depending on installation environment.
English Français Español Nederlands Italiano Deutsch
3
JO S - 1 A JO S - 1 V JO S - 1 F
JO - 1 M D
Front panel M ain unit
JO - DA
JO - DV
Flush m ount
b ack b ox S pecial screw
x4
JO - DV F
M anual
S pecial screw drive r
S pecial screw drive r ( H exa gonal w rench)
T ransparent nam e plate x2
PACKAGE CONTENTS
NO T ES :
• Mounting and Wood mounting screws
not included
• For details on the power supply, see
the installation manual separately.
EnglishFrançaisEspañolNederlandsItalianoDeutsch
4
Color LCD screen
Displays camera images during door
station call-ins, communication with door
station, and door station monitoring Status LED (orange)
Indicates the current status of this station by lighting up or blinking.
On: During communication sending, while the door release button is
being pressed, or while the option button is being pressed
Flashing: During communication reception in the PTT mode, during
short detection or during mute
Option button
To activate/trigger external device
Door release button
Unlocks door
Talk/off button
Starts or ends communication.
Speaker
Call tones, sounds from a door station.
RESET button
Press this button to reboot this
station when it is not responding.
Microphone
Sends sounds from this station
to other stations.
[Bottom View]
Monitor button
Monitor a door station
Volume control button
[During standby]
Adjust the calling volume.
Volume adjustment range: (mute), -
[During communication or monitoring]
Adjust the communication volume.
Volume adjustment range: -
Screen brightness control button
Adjusts LCD screen brightness
Brightness adjustment range: -
PART NAMES Remove protective film before use.
JO - 1 M D
Camera
Captures images to display on the screens of
the master and expansion monitor station.
Sends sounds from the door station to the
master and expansion monitor station.
Detects outside illuminance to recognize whether
it is daytime or nighttime.
These are for discharging rain water inside the unit.
Do not obstruct these holes.
Outputs sounds from the master or expansion monitor station.
Calls the preset master and expansion monitor station.
Lights up automatically when it gets dark around this station.
The backlight is always lit while
the power is on.
Camera
Microphone
Camera-angle
adjustment switch
Illumination sensor
Speaker
Call button with white light LED
Microphone
White light LED
Name plate
(with backlight)
Speaker
Vandal resistant front panel
Call button
Camera
Illumination
sensor Illumination
sensor
Microphone
White light LED
Name plate
(with backlight)
Speaker
Call button
Drainage holes
Vandal resistant front panel
Drainage holes
Camera-angle adjustment switch
The camera-angle adjustment switch is behind
the panel. Pushing the button changes the angle
of the camera.
+17° (Upward)
+7° (Upward)
0° (Center)
-7° (Downward)
JO - DA
JO - DV F
JO - DV
English Français Español Nederlands Italiano Deutsch
5
INSTALLATION
W iring m ethod, w iring distance
JO-1MD
JO-DA JO-DV
JO-DVF : PS-1820, PS-1820S, PS1820UL, PS-1820D
A
BC IER-2
PS18
Ø 0.65 mm 22 AWG Ø 0.8-1.2 mm 20-16 AWG
A 50 m 165'100 m 330'
B 5 m 16'10 m 33'
C 50 m 165'150 m 495'
C ab le
Use PE (polyethylene)-insulated PVC jacket cable.
Parallel or jacketed 2-conductor, mid-capacitance, non-shielded
cable is recommended.
Never use individual conductors, twisted pair cable, or
coaxial cable.
M ounting locations
JO - DA , JO - DV , JO - DV F
In direct sunlight
ab c
Under street lights or door lights Other locations subject to strong
lighting or backlighting
conditions
JO - 1 M D
In direct sunlight Avoid installing the master monitor
station in a concave space
of a wall to prevent
disconnection of
communication
Allow at least 15 cm (6") above
and 25cm (9") below center of
the mounting
bracket for
installation
of the station
15 cm (6
"
)
or more
25 cm (9
"
)
or more
ab c
Do not install door station and master monitor station in any of the following locations where lighting or the ambient environment
could impact the display on the video monitor.
M ounting positions and im age vi ew area
JO - DA , JO - DV , JO - DV F
Approx. 950 mm
500 mm
[Horizontally] [Vertically] [Vertically] [Vertically]Camera angle: 0°
Approx. 1,800 mm
1,500 mm
Unit
center
(5' 11")
(1' 9")
(3' 1")
(20")
(5')
(4' 1")
(20")
500
mm
Approx. 550 mm
Approx. 1,250 mm
Camera angle: 7°
Unit
center Unit
center
Unit
center
Approx. 1,750 mm
1,300 mm
Approx. 600 mm
Approx. 1,150 mm
(5' 9")
(3' 9") (4' 4")
(2')
(20")
500
mm
Camera angle: 17°
1,300 mm
Approx. 1,900 mm
Approx. 1,250 mm
Approx. 650 mm
(20")
500
mm
(6' 4")
(2' 2")
(4' 1") (4' 4")
[Vertically]Camera angle: -7°
(When the station is at a high position due to a step)
1,500
mm
Approx. 1,900 mm
150 mm
Approx. 1,300 mm
Approx. 600 mm
(20")
500
mm
(5')
(4' 4")
(6' 4")
(2')
(5")
JO-DA: Refer to below diagrams when the camera angle is changed with the
adjustment switch.
EnglishFrançaisEspañolNederlandsItalianoDeutsch
6
< B ack w iring>
83.5mm (3-5/16")
8mm
(3/8")
3 - gang b ox
M ounting screw × 4
(Screw shaft: Ø4.1)
(Slotted Head: Ø8.2 or less
Height 3.0mm or less)
(not included)
M ounting b racke t
(attached to the unit with shipment)
Mount the unit on the
mounting bracket.
3
Fasten the mounting
bracket to the wall
1
21. Press release button to insert or remove wire.
2. Insert wire into the terminal.
JO - 1 M D
MOUNTING
W ires
< S urf ace w iring>
When the wiring is not coming through the wall, the wires can be routed to the top or bottom of the unit. Remove cable inlet plate on
the upper part of the unit to allow passage of the wiring into the unit.
92mm (3-5/8")
83.5mm
(3-5/16")
M ounting b racke t
(attached to the unit with
shipment)
W ood m ounting screw × 4
(Screw shaft: Ø4.1)
(Slotted Head: Ø8.2 or less
Height 3.0mm or less)
(not included)
W ires
R em ove cab le inlet plate
English Français Español Nederlands Italiano Deutsch
7
Place " UP" upwards
Mounting screw x 2
(Screw shaft: Ø4.1)
(Slotted Head: Ø8.2 or less
Height 3.0mm or less)
(not included)
Mounting screw x 2
(Screw shaft: Ø4.1)
(Slotted Head: Ø8.2 or less
Height 3.0mm or less)
(not included)
Main unit
1-gang box
Mounting frame
83.5 mm
(3-5/16")
83.5 mm
(3-5/16")
Mount the main unit on
the mounting frame,
and fit the front panel on.
Pry off the front panel with
a flathead screwdriver.
Removing the front panel
Flathead screwdriver
Front panel Main unit
Remove the main unit from
the mounting frame by
loosening the locking screws
1
Fasten the mounting
frame to the wall.
2
Connect wires.
3
Tighten
Screwdriver
Loosen
Drainage hole
Do not block the holes.
Insert a wire from the lower side.
<Back wiring> <Bottom surface>
<Surface wiring>
Installation height
(center of the unit)
1,500 mm (5')
Wire slot
JO - DA
Loosen the special screw
with the special screwdriver,
and remove the front panel.
1
Fasten the unit to the mounting surface.
*Use board anchors or concrete plugs as needed.
4
Replace face plate and tighten
screw with included special
screwdriver.
5
75 mm
3''
Special
screwdriver
(included)
Loosen
Tighten
Vanda resistant
front panel
Anchor x 4
(Prepare anchors according to the size of the mounting screws.)
(not included)
The unit
Mounting screw × 4
(Screw shaft: Ø4.1)
(Slotted Head: Ø8.2 or less
Height 3.0mm or less)
(not included)
Special
screw
Insert the transparent name plate.
Peel off the protective seals on the plate (both sides).1.Fill in the name on the transparent name plate.
Be sure to leave 25 mm (1") of white space on the right
end to account for insertion.
2.
Insert the filled-in transparent name plate as below
(indicated with in diagram).
3.
2
ABCDEFG
2 mm (1/8")
25 mm
(1")
Insert transparent
name plate here.
150 mm
5-15/16''
Drainage hole
Do not block the holes.
(The diameter and the depth of the holes on the wall depend on
the anchors suitable for the mounting screws used.)
50 mm
1-31/32''
Connect wires to the unit.
3
70 mm
2-3/4''
JO - DV
110 mm
4-3/8''
180mm
7-3/32''
45 mm
1-25/32''
Vandal resistant front panel with the unit attached
Flush mount back box
(included)
Transparent name plate
Special
screw x 4
(included)
Hexagonal wrench (included)
Tighten
Loosen
Install the flush mount back box in
the wall, and then connect the wires to
the unit with the terminal cover open.
1
Insert the transparent name plate.
*See above JO-DV for details.
2
Fasten the front panel to the back
box with the special screws.
3
JO - DV F
EnglishFrançaisEspañolNederlandsItalianoDeutsch
8
WIRING
1
E
A1 A2
2
NP
2
NP
2
P
2
NP
PS-1820
PS-1820S
PS-1820UL
PS-1820D
PS18
PS18
IER-2
JO-DV JO-DVF
JO-1MD
: Power supply
IN 230V~ 50/60Hz
L
N
LN
-
++
-
+
-
230V AC
50/60 Hz 18V DC 2A
18V DC 2A
JO-DA
+
-
100V - 240V
50/60 Hz
Insert wires securely into each terminal as shown.
Door release
An EL-12S (AC 12 V, 0.125 A, DC 12 V, 0.2 A) or
equivalent part and a separate AC transformer (or
power supply) are required.
Door release contact: AC/DC 24 V, 0.5 A
(Minimum contact: 100 mV DC, 0.1 mA)
(N/O dry closure contact L, L).
*Run separate cables for audio/video and door release.
Call tone from door station.
Electric door
strike A C transf orm er
M aster m onitor station
( T o optional units)
(AC/DC 24V, 0.5A N/O dry closure contact)
(Minimum contact: 100mV DC, 0.1mA)
V ideo door station
C all ext ension speake r
IER - 2
EL - 1 2 S
P resence of sound f rom IER - 2
NP: Non-polarized
P: Polarized
NO T ES :
• To add an expansion monitor station, see the installation
manual of the expansion monitor station.
Without grounding, the units may not operate
normally.
English Français Español Nederlands Italiano Deutsch
9
OPERATIONS
1Press and hold for 2 seconds or more.
After approx. 2 seconds beep sounds, PTT mode is engaged.
• If is pressed briefly, PTT mode is not engaged.
2When communicating, keep pressed. To hear the caller’s voice,
release .
Status LED lights when you talk, and flashes slowly as you listen to caller
(or hear outside sounds).
NO T ES :
• It is not possible to switch back to hands-free mode (from PTT mode
during communication).
For loud outdoor areas, use P ress- to- T alk m ode ( P T T )
1Push Call button.
2The call tone sounds, an image appears on screen.
• The screen turns off after approx. 45 seconds if not answered.
3Push , and after the beep, communicate hands-free (hands-free mode).
4After finishing communication, push and communication
will end after the beep.
NO T ES :
• Communication ends automatically after approx. 1 minute.
• The communication volume can be adjusted during the monitoring or
the communication by pressing .
There are three communication volume settings to cycle through:
[
] (Minimum), [
] (Medium), and [
] (Maximum). The current
volume level is displayed on the screen and disappears in approx. 5
seconds. The default setting is [
] (Medium).
A nsw ering a door call
1Press .
2Door release is activated and door can be opened.
During release: Status LED lights.
A ctiva ting door release
A f ter 2 seconds or m ore
EnglishFrançaisEspañolNederlandsItalianoDeutsch
1 0
1Push in standby mode.
2The video image from the door station and the incoming audio is heard.
If you do not push , the caller will not hear sounds from the inside
station.
3Push to end monitoring.
NO T ES :
• To talk to door station during monitoring, momentarily push .
This allows communication with the door station.
• The monitoring turns off automatically after approx. 1 minute.
M onitoring door station
1Push in standby mode to adjust call tone volume and display the
volume level.
2Push until the desired call tone volume level is heard.
NO T ES :
• There are four call tone volume settings to cycle through:
[] (Mute), [
] (Minimum) - [
] (Maximum).
The current volume level is displayed on the screen and disappears
in approx. 5 seconds. The default setting is [
] (Medium).
A dj ust call tone vo lum e
< W hen a call is m ade f rom the door station>
If Call button is pushed, the White light LED lights up.
When communication ends, the White light LED will turn off.
< W hen the w hite light L ED is lit up during m onitoring door station>
When is pushed during monitoring door station, the White light LED
will light up.
When monitoring door station ends, the White light LED will turn off.
NO T ES :
• The door station evaluates lighting conditions to automatically turn
on the white light LED when necessary.
♪
♪
At night, the door station White light LED lights up during calling or monitoring door station.
Night illum ination
English Français Español Nederlands Italiano Deutsch
1 1
TECHNICAL PRECAUTIONS
SPECIFICATIONS
C leaning:
• Clean all units with a soft cloth and gentle cleaner. Do not spray cleaner directly on unit. Do not use an abrasive cleaner or cloth.
• Door stations are weather resistant.
W iring:
• When a short is detected between A1 and A2 of the door station, the unit stops functioning and the Status LED flashes rapidly until the
short is removed. Check the wires.
• If noise is heard from the master monitor station, the wiring is disconnected between the video door station and the master monitor
station.
T roub le:
• If the station does not respond, reboot this station by pressing the RESET button.
• When the power supply is turned off, power failure, or the RESET button is pressed, the setting of brightness, communication volume,
and call tone volume are returned to the default setting.
JO - 1 M D ( M aster m onitor station)
Power supply DC 18V (from power supply)
Current consumption (standby) 24mA (max) 410mA
Communication Hands-free: Auto-voice actuation
PTT: Press-to-talk, release to listen
Ambient temperature 0 - 40°C (+32°F - +104°F)
Monitor 7 inch color LCD screen
Mounting Wall-mount
Electrical box 3-gang box
Material Flame resistant ABS resin
Color White
Dimension 130 (H) x 230 (W) x 21 (D) (mm)
5-1/8 (H) x 9-1/16 (W) x 13/16 (D) (inches)
Weight Approx. 470g (1.04 lbs.)
JO - DA / JO - DV / JO - DV F ( V ideo door station)
Camera unit 1/4 - inch color CMOS
Ambient temperature -20 - 60°C (-4°F - +140°F)
Minimum illumination Approx. 5 lux at 50 cm (1'6'') distance
Dimensions (JO-DA) 129 (H) x 97 (W) x 36 (D) (mm)
5-3/32 (H) x 3-27/32 (W) x 1-13/32 (D) (inches)
(JO-DV) 173 (H) x 98 (W) x 27 (D) (mm)
6-13/16 (H) x 3-7/8 (W) x 1-3/8 (D) (inches)
(JO-DVF) 209 (H) x 135 (W) x exposed area 3.5 (D) (mm)
8-1/4 (H) x 5-5/16 (W) x 5/16 (D) (inches)
(Flush mount back box
for JO-DVF)
180 (H) x 110 (W) x 45 (D) (mm)
7-3/32 (H) X 4-3/8 (W) X 1-25/32 (D) (inches)
Weight (JO-DA) Approx. 200 g (0.44 lbs.)
(JO-DV) Approx. 650 g (1.43 lbs.)
(JO-DVF) Approx. 580 g (1.27 lbs.)
(Flush mount back box
for JO-DVF) Approx. 550 g (1.2 lbs.)
IP rating IP54 (JO-DA / JO-DV / JO-DVF)
IK rating IK08 (JO-DV)
IK07 (JO-DVF)
1Press to operate to the unit’s option output.
NO T ES :
• Optional devices must be installed and connected properly.
The can control lights, secondary doors, garages, etc.
• While the button is pressed, the N/O dry closure contact signal
is kept being output.
A ctiva ting/ T riggering ext ernal devi ces ( if installed)
1Push when the screen is difficult to see. The screen brightness
changes from [ 1] (the darkest) to [ 5] (the brightest) during
communication or monitoring.
NO T ES :
• The current brightness level is displayed on the screen and
disappears in approx. 5 seconds.
• The default setting is [ 3].
A dj ust screen b rightness
6 3
MEMO
Aiphone warrants its products to be free from defects of material and workmanship under normal
use and service for a period of two years after delivery to the ultimate user and will repair free of
charge or replace at no charge, should it become defective upon which examination shall disclose
to be defective and under warranty. Aiphone reserves unto itself the sole right to make the final
decision whether there is a defect in materials and/or workmanship; and whether or not the product
is within the warranty. This warranty shall not apply to any Aiphone product which has been
subject to misuse, neglect, accident, power surge, or to use in violation of instructions furnished,
nor extended to units which have been repaired or altered outside of the factory. This warranty does
not cover batteries or damage caused by batteries used in connection with the unit. This warranty
covers bench repairs only, and any repairs must be made at the shop or place designated in writing
by Aiphone. This warranty is limited to the standard specifications listed in the operation manual.
This warranty does not cover any supplementary function of a third party product that is added
by users or suppliers. Please note that any damage or other issues caused by failure of function
or interconnection with Aiphone products is also not covered by this warranty. Aiphone will not
be responsible for any costs incurred involving on site service calls. Aiphone will not provide
compensation for any loss or damage incurred by the breakdown or malfunction of its products
during use, or for any consequent inconvenience or losses that may result.
The object area of is the EU.
Aiphone garantiza que sus productos están libres de defectos de material y mano de obra, en uso y
servicio normal, por un período de dos años después de la entrega final al último usuario y reparará
sin costo, o reemplazará sin cargo, si llegara a resultar defectuoso, mediante una inspección que
determine que efectivamente está con defecto y en garantía. Aiphone se reserva para sí la facultad
única de tomar la decisión final para juzgar si existe una falla en materiales y/o mano de obra, y
si el producto está o no cubierto por la garantía. Esta garantía no se aplicará a ningún producto
Aiphone que haya sido sometido a maltrato, negligencia, accidente, sobrecarga de energía o que
haya sido usado de manera diferente a las instrucciones proporcionadas, o bien por las unidades que
hayan sido reparadas o alteradas fuera de fábrica. Esta garantía no cubre baterías o daños causados
por baterías usadas en conjunto con la unidad. La garantía cubre solo las reparaciones efectuadas
en la mesa de trabajo y cualquier reparación debe ser efectuada en el taller o lugar designado por
escrito por Aiphone. Esta garantía se limita a las especificaciones estándar indicadas en el manual
de funcionamiento. Esta garantía no cubre ninguna función adicional de un producto de terceros que
haya sido añadido por los usuarios o proveedores. Tenga en cuenta que los daños u otros problemas
causados por un fallo de funcionamiento o por la interconexión con los productos de Aiphone
tampoco están cubiertos por la garantía. Aiphone no se responsabilizará por costos incurridos en
cualquier llamada de servicio al sitio mismo en que se presente el defecto. Aiphone no indemnizará
por ninguna pérdida o daño en que se incurra debido a la avería o falla de sus productos durante su
uso, ni por ningún inconveniente o pérdida que se produzca como consecuencia.
El área de objeto de es la UE.
Aiphone garantit que ses produits ne sont affectés d'aucun défaut de matière ni de fabrication, en
cas d'utilisation normale et de réparations conformes, pendant une période de deux ans après la
livraison à l'utilisateur final, et s'engage à effectuer gratuitement les réparations nécessaires ou à
remplacer l'appareil gratuitement si celui-ci présente un défaut, à la condition que ce défaut soit
bien confirmé lors de l'examen de l'appareil et que l'appareil soit toujours sous garantie. Aiphone se
réserve le droit exclusif de décider s'il existe ou non un défaut de matière et/ou de fabrication et si
l'appareil est ou non couvert par la garantie. Cette garantie ne s'applique pas à tout produit Aiphone
qui a été l'objet d'une utilisation impropre, de négligence, d'un accident, d'une surtension ou qui a
été utilisé en dépit des instructions fournies ; elle ne couvre pas non plus les appareils qui ont été
réparés ou modifiés en dehors de l'usine. Cette garantie ne couvre pas les piles ni les dégâts infligés
par les piles utilisées dans l'appareil. Cette garantie couvre exclusivement les réparations effectuées
en atelier. Toute réparation doit être effectuée à l'atelier ou à l'endroit précisé par écrit par Aiphone.
Cette garantie est limitée aux spécifications standard répertoriées dans le manuel d'utilisation. Cette
garantie ne couvre pas les fonctions supplémentaires d'un produit tiers ajouté par les utilisateurs ou
fournisseurs. Veuillez noter que les dommages ou autres problèmes causés par l'échec de fonction
ou interconnexion avec les produits Aiphone ne sont pas non plus couverts par cette garantie.
Aiphone décline toute responsabilité en cas de frais encourus pour les dépannages sur site. Aiphone
n'indemnisera pas le client en cas de pertes, de dommages ou de désagréments causés par une
panne ou un dysfonctionnement d'un de ses produits lors de l'utilisation, ou pour toute perte ou tout
problème qui peut en résulter.
La zone d'application de est l'UE.
Aiphone waarborgt zijn producten tegen materiaal- en fabricagefouten bij normaal gebruik en
onderhoud gedurende een periode van twee jaar na levering aan de eindgebruiker, en zal het
product kosteloos herstellen of vervangen indien na onderzoek blijkt dat het toestel een defect
heeft dat onder de waarborg valt. Aiphone behoudt zich het recht voor als enige definitief te
bepalen of er al dan niet sprake is van een materiaal- en/of fabricagefout en of het product nog
onder waarborg is. Deze waarborg geldt niet voor ieder Aiphoneproduct dat is blootgesteld aan
verkeerd gebruik, verwaarlozing, een ongeval, stroomstoten, of verkeerde bediening en evenmin
voor toestellen die buiten de fabriek zijn hersteld of aangepast. Deze waarborg geldt niet voor
batterijen of schade veroorzaakt door batterijen die in het toestel zijn uitgebreid. Deze waarborg
dekt uitsluitend werkbankherstellingen en iedere herstelling moet worden uitgevoerd in een
schriftelijk door Aiphone aangewezen winkel of werkplaats. Deze waarborg beperkt zich tot de
standaardspecificaties die in de bedieningshandleiding staan vermeld. Deze waarborg beslaat
geen enkele aanvullende functie van een product van een externe partij dat door gebruikers of
leveranciers wordt toegevoegd. Gelieve op te merken dat schade of andere problemen die het
gevolg zijn van storing bij gebruik of verbinding met producten anders dan die van Aiphone,
eveneens niet door deze waarborg worden gedekt. Kosten die gepaard gaan met herstellingen ter
plaatse kunnen niet worden verhaald op Aiphone. Er kan geen schadeloosstelling van Aiphone
worden geëist voor enig verlies of schade als gevolg van een defect of storing tijdens het gebruik
van zijn producten, of voor enig ongemak of verlies dat hieruit voortvloeit.
Het toepassingsgebied van is de EU.
Aiphone garantiert, dass seine Produkte frei von Material- oder Verarbeitungsfehlern sind bei
normalem Gebrauch für die Dauer von zwei Jahren nach der Auslieferung an den Endnutzer
und wird kostenlose Reparaturen oder Austausche vornehmen, sollte das Gerät einen Defekt
aufweisen, der nach eingehender Überprüfung innerhalb der Garantie liegt. Aiphone behält sich
das alleinige Recht vor, endgültige Entscheidungen zu treffen, ob ein Defekt am Material und/oder
in der Verarbeitung vorliegt; und ob das Produkt innerhalb der Garantie liegt. Diese Garantie trifft
auf kein Aiphone-Produkt zu, welches Gegenstand von Missbrauch, Fahrlässigkeit, Unfall und
Stromüberladung gewesen ist oder in Verletzung geltender Vorschriften genutzt wurde, und wird
nicht auf Geräte ausgeweitet, die außerhalb des eigenen Werks repariert oder verändert wurden.
Die Garantie deckt keine Batterien oder Schäden, die durch Batterien in Verbindung mit dem
Gerät verursacht wurden, ab. Die Garantie deckt nur Werkstattreparaturen ab und alle Reparaturen
müssen in den von Aiphone schriftlich vorgesehenen Geschäften oder Orten durchgeführt werden.
Die Garantie ist auf die im Betriebshandbuch angegebenen Standardspezifikationen beschränkt.
Die Garantie deckt keinerlei ergänzenden Funktionen von Drittanbieter-Produkten, die vom Nutzer
oder Händler hinzugefügt wurden, ab. Beachten Sie, dass jegliche Schäden oder andere Probleme,
die durch eine Verwendung des Geräts mit anderen Produkten als Aiphone-Produkten entstehen,
nicht von der Garantie abgedeckt sind. Aiphone ist für alle anfallenden Kosten hinsichtlich örtlicher
Service-Anrufe nicht verantwortlich. Aiphone bietet keinerlei Kompensation für jegliche Verluste
oder Schäden, die aufgrund eines Ausfalls oder einer Fehlfunktion seines Produkts verursacht
wurden, noch für etwaige Unannehmlichkeiten oder Verluste.
Das Anwendungsgebiet von ist die EU.
Aiphone garantisce che i suoi prodotti sono privi di difetti nei materiali o nella lavorazione, in
condizioni di utilizzo normali e per un periodo di due anni dalla consegna all'utente fi nale. Aiphone
eseguirà la riparazione o la sostituzione gratuita del prodotto qualora tale prodotto risulti difettoso
e la garanzia sia applicabile al difetto rilevato. Aiphone si riserva il diritto esclusivo di stabilire in
via defi nitiva se sono presenti difetti nei materiali e/o nella lavorazione e se il prodotto è coperto
dalla garanzia oppure no. La presente garanzia non è applicabile ad alcun prodotto Aiphone che sia
stato sottoposto ad uso improprio, negligenza, incidente, sovracorrente o che sia stato utilizzato in
violazione alle istruzioni fornite, né può essere estesa alle unità che sono state riparate o manomesse
al di fuori della fabbrica. Questa garanzia non copre le batterie né i danni causati dalle batterie
usate in connessione con l'unità. Questa garanzia copre solo le riparazioni del prodotto consegnato
presso il punto designato. Le eventuali riparazioni devono essere eseguite presso il punto vendita
o il luogo designato per iscritto da Aiphone. Questa garanzia è limitata alle specifi che standard
elencate nel manuale d'uso. Questa garanzia non copre le funzioni supplementari di prodotti di altre
aziende aggiunti dagli utenti o dai fornitori. Eventuali danni o altri problemi causati da problemi
di funzionamento o interconnessione con prodotti Aiphone non sono coperti da questa garanzia.
Aiphone non potrà essere ritenuta responsabile di eventuali costi sostenuti in caso di chiamata per
l'assistenza sul posto. Aiphone non offrirà alcun compenso per gli eventuali danni o perdite subiti
a causa della rottura o del guasto dei suoi prodotti durante l'uso, o per qualsiasi disagio o perdita
conseguente che si dovesse verifi care.
L'area oggetto di è l'UE.
WARRANTY GARANTÍA
GARANTIE WAARBORG
GARANTIE GARANZIA
English Español
Français Nederlands
Deutsch Italiano
P rinted in T hailand
A IP H O NE C O . , L T D. , NA G O Y A , J A P A N
http://www.aiphone.net/
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
Intelligent Home Aiphone JO Manual de usuario
- Tipo
- Manual de usuario
En otros idiomas
- français: Intelligent Home Aiphone JO Manuel utilisateur
- English: Intelligent Home Aiphone JO User manual
- Deutsch: Intelligent Home Aiphone JO Benutzerhandbuch
- Nederlands: Intelligent Home Aiphone JO Handleiding