Samsung DV484ETHAWR/A1-0001 Manual de usuario

Marca: Samsung

Modelo: DV484ETHAWR/A1-0001

Categoría: Secadoras

Tipo: Manual de usuario

Este manual también es adecuado para

100%

Recycled Paper

the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service or accessor

Dar!:s. iolease register your product at or contact

www.samsung.comiregister

1-800-SAMSUNG (726-78641

DVDV476 484 03022E-01 EN 20120710.indd 1 2012-07-10 z- 5:27:13 I

1. Extra Large Capacity

Ultra drying capabilities are at your fingertips! Now you can dry extra-large loads. Our

ultralarge 7.4cu.ft capacity dryer circulates more air through your clothes, drying them faster,

for a wrinkle-free result.

2. Steam Cycle

This cycle sprays a small amount of water into the dryer drum after several minutes of

tumbling with heat. It reduces bad odors from clothing that are difficult to remove when

washing with water, and also reduces wrinkles.

3. Sanitize Cycle

This cycle sanitizes garments by infusing high temperature heat deep into the fabric during

the drying cycle and eliminating 99.9% of certain bacteria.Use this cycle for clothing,

bedding, towels, or other items needing sanitization. The Sanitize cycle is certified by NSF

International, an independent third-party testing and certification organization.

_S_ NSF Protocol P154

Sanitization Performance of

Residential Clothes Dryers

4. Various Drying Cycles & Fuzzy Logic Algorithm

Simply turn the Jog Dial to select one of the 13 automatic drying cycles, including normal,

heavy duty and bedding, or let the Fuzzy Logic Control measure the degree of dampness

and automatically set the drying time. Precision drying has never been easier than with

Samsung.

5. Time Saving

Our cycles are designed with you in mind. All our dryers are designed to dry your clothes in

less time.., just 42 minutes! Giving you time for more important things in life.

6. Energy Saving

Samsung dryers are super energy efficient. You can dry up to 3.09 pounds of laundry with

1kWh. Also, both the large capacity and Fuzzy Logic Control save energy by automatically

drying your clothes the most efficient way.

2 Features

DVDV47d 484 03022E-01 EN 20120710.indd Sec9:2 2012-07-10 vv 5:27:21 I

7. Easy Reversible Door

The direction of our reversible door can be changed easily.

8. 4-way Vent (electric model only)

You can install the exhaust vent in the following four (4) positions: back, either side, bottom.

DVDV47d 484 03022E-01 EN 20120710.indd Sec9:3

Feat ur'es 3

2012-07-10 _ 5:27:21 I

s f tv nstrLActons

Congratulations on your new Samsung Dryer.This manual contains valuable

information on the installation, use, and care of your appliance. Please take the

time to read this manual to take full advantage of your dryer's many benefits and

features.

WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS

Warnings and Important Safety Instructions in this manual do not cover all possible conditions and

situations that may occur. It is your responsibility to use common sense, caution, and care when installing,

maintaining, or operating your dryer.

Always contact your manufacturer about problems or conditions you do not understand.

IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS

What the icons and signs in this user manual mean:

z£

WARNING

Hazards or unsafe practices that may result in severe personal injury

or death.

Follow the information in this manual to minimize the risk of fire or

explosion or to prevent property damage, personal injury, or death.

Do not store or use gasoline or other flammable vapors and liquids near

this or any other appliance.

Hazards or unsafe practices that may result in minor personal injury or

CAUTION property damage.

Do NOT attempt.

Do NOT disassemble.

[_ Do NOT touch.

Follow directions explicitly.

Unplug the power plug from the wall socket.

Make sure the machine is grounded to prevent electric shock.

Call the service center for help.

(_ Note

These warning signs are here to prevent injury to you and others.

Please follow them explicitly.

After reading this section, keep it in a safe place for future reference.

(_ Read all instructions before using the appliance.

SAVE THESE INSTRUCTIONS

4 safety ir_structior_s

DVDV47d 484 03022E-01 EN 20120710.indd Secll:4 2012-07-10 _ 5:27:21 I

WARNING: To reduce the risk of fire, electric shock, or injury to when using

persons your

....... appliance, follow basic precautions, including the following:

1. Read all instructions before using this appliance.

2. Do not dry articles that have been previously cleaned in, washed in, soaked in,

or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive

substances, as they give off vapors that could ignite or explode.

3. Do not use the dryer to dry clothes which have traces of any flammable substance,

such as vegetable oil, cooking oil, machine oil, flammable chemicals, thinner, etc., or

anything containing wax or chemicals, such as mops and cleaning cloths. Flammable

substances may cause the fabric to catch fire by itself.

4. Do not store or use gasoline or other flammable vapors and liquids near this or any

other appliance.

5. Do not allow children to play on or in the appliance. Close supervision of children is

necessary when the appliance is used near children.

6. Before the appliance is removed from service or discarded, remove the door to the

drying compartment.

7. Do not reach into the appliance if the drum is moving.

8. Do not install or store this appliance where it will be exposed to the weather.

9. Do not tamper with controls.

10. Do not repair or replace any part of the appliance or attempt any servicing unless

specifically recommended in the user-maintenance instructions or in published user-

repair instructions that you understand and have the skills to carry out.

11. Do not use fabric softeners or products to eliminate static unless recommended by the

manufacturer of the fabric softener or product.

12. Clean the lint screen before or after each load.

13. Do not use heat to dry articles containing foam rubber or similarly textured rubber-like

materials.

14. Keep area around the exhaust opening and adjacent surrounding areas free from the

accumulation of lint, dust, and dirt.

15. The interior of the appliance and exhaust duct should be cleaned periodically by

qualified service personnel.

16. Do not place items exposed to cooking oils in your dryer. Items contaminated with

cooking oils may contribute to a chemical reaction that could cause a load to catch fire.

WARNING

State of California Preposition 65 Warnings:

The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of

California to publish a list of substances known to the State of California to cause cancer,

birth defects, or other reproductive harm, and requires businesses to warn of potential

exposure to such substances.

This product contains a chemical known to the State of California to cause cancer, birth

defects, or other reproductive harm. This appliance can cause low-level exposure to some

of the substances listed, including benzene, formaldehyde, and carbon monoxide.

Gas appliances may cause low-level exposure to some of the substances listed including

benzene, formaldehyde, carbon monoxide, and soot; as a result of possible incomplete

combustion of natural gas or LP fuels. Exposure to these substances can be minimized

further by properly venting the dryer to the outdoors.

SAVE THESE INSTRUCTIONS

safety instructions 5

DVDV47d 484 03022E-01 EN 20120710.indd Secll:5 2012-07-10 _ 5:27:21 I

WARNING - Risk of Fire

Clothes dryer installation must be performed by a qualified installer.

• Install the clothes dryer according to the manufacturer's instructions and local codes.

Do not install a clothes dryer with flexible plastic venting materials. If flexible metal

(foil type) duct is installed, it must be of a specific type identified by the appliance

manufacturer as suitable for use with clothes dryers. Flexible venting materials are

known to collapse, be easily crushed, and trap lint. These conditions will obstruct

clothes dryer airflow and increase the risk of fire.

To reduce the risk of severe injury or death, follow all installation instructions.

reduce the risk of fire or explosion:

Do not dry items that have been previously cleaned, washed, soaked, or spotted with

gasoline, dry cleaning solvents, or other flammable or explosive substances. They

emit vapors that could ignite or explode. Any material that has been in contact with a

cleaning solvent or flammable liquids or solids should not be placed in the dryer until all

traces of these flammable liquids or solids and their fumes have been removed.

There are many highly flammable items used in homes, such as acetone, denatured

alcohol, gasoline, kerosene, some liquid household cleaners, some spot removers,

turpentine, waxes, and wax removers

Items containing foam rubber (may be labeled latex foam) or similarly textured rubber-

like materials must not be dried on a heat setting. Heated foam rubber materials can,

under certain circumstances, produce fire by spontaneous combustion.

w_.,._What to do if you smell gas:

• Do not try to light any appliance.

• Do not turn on the appliance.

Do not touch any electrical switch.

Do not use any phone in your building.

• Clear the room, building or area of all occupants.

Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

• Installation and service must be performed by a qualified installer, service agency, or the

gas supplier.

SAVE THESE INSTRUCTIONS

safety instructior_s

DVDV47d 484 03022E-01 EN 20120710.indd Secll:6 2012-07-10 vv 5:27:21 I

Do not allow children or pets to play on, in, or in front of the appliance. Close supervision is

necessary when the appliance is used near children and pets.

Before discarding or removing your dryer from service, remove the door to the drying

compartment to prevent children or animals from becoming trapped inside.

Do not reach into the appliance when the drum is moving.

Do not install or store this appliance where it will be exposed to the weather.

Do not tamper with controls.

Do not repair, replace, or attempt to service any part of the appliance unless specifically

instructed to in the user-repair instructions and you have the understanding and skills to

carry out the procedure.

Do not use fabric softeners or products to eliminate static unless the softener or product is

recommended for dryer use by the manufacturer of the fabric softener or product.

Clean the lint screen before or after each load.

Keep the area around the exhaust opening and surrounding areas free from lint, dust, and dirt.

The interior of the dryer and exhaust duct should be cleaned periodically by qualified service

personnel.

This appliance must be properly grounded. Never plug the power cord into a receptacle

that is not grounded adequately and in accordance with local and national codes. See

installation instructions for information about grounding this appliance.

Do not sit on top of the dryer.

Z_ Ensure pockets are free from small, irregularly shaped hard objects, foreign material, etc. ie.

....... coins, knives, pins, etc. These objects could damage your dryer.

Do not wash clothing with large buckles, buttons, or other heavy metal or solid objects.

/_ Gas leaks may occur in your system, resulting in a dangerous situation.

WARNIN_

Gas leaks may not be detected by smell alone.

Gas suppliers recommend you purchase and install a UL-approved gas detector.

Install and use in accordance with the manufacturer's instructions.

Do not place items in your dryer that have been spotted or soaked with vegetable oil or cooking

oil. Even after being washed, these items may contain significant amounts of these oils.

Residual oil on clothing can ignite spontaneoulsy. The potential for spontaneous

combustion increases when items containing vegetable oil or cooking oil are exposed to

heat. Heat sources such as your dryer can warm these items, allowing an oxidation reaction

in the oil to occur. Oxidation creates heat. If this heat cannot escape, the items can become

hot enough to catch fire. Piling, stacking, or storing these kinds of items may prevent heat

from escaping and can create a fire hazard.

All washed and unwashed fabrics that contain vegetable oil or cooking oil can be

dangerous. Washing these items in hot water with extra detergent will reduce, but not

eliminate, the hazard. Always use the Cool Down cycle for these items to reduce their

temperature. Never remove these items from the dryer hot or interrupt the drying cycle until

the items have run through the Cool Down cycle. Never pile or stack these items when they

are hot.

SAVE THESE INSTRUCTIONS

safety instructions 7

DVDV47d 484 03022E-01 EN 20120710.indd Secl:7 2012-07-10 _ 5:27:21 I

cont nt,s

iNSTALLiNG YOUR DRYER

OPERATING iNSTRUCTiONS, TIPS

CARE AND CLEANING

SPECIAL LAUNDRY TIPS

9 Unpacking your dryer

10 Basic requirments

11 Ducting requirements

12 Important to installer

12 Location considerations

12 Alcove or closet installation

13 Mobile home installation

13 Exhausting

14 Gas requirements

14 Commonwealth of Massachusetts

installation instructions

15 Electrical requirements

15 Grounding

16 Electrical connections

17 Installation - General procedure

19 Final installation checklist

20 Connecting the inlet hose

22 Dryer Exhaust Tips

23 Door Reversal

Overview of the control panel

Child lock

Drum Light

Rack Dry

Clean the lint filter

Load the dryer properly

Getting started

30 Control Panel

30 Tumbler

30 STAINLESS STEEL TUMBLER (DV476")/

Powder Coated Tumbler (DV484")

30 Dryer Exterior

30 Dryer Exhaust System

31 Special laundry tips

TROUBLESHOOTING

32 Check these points if your dryer...

33 Information codes

APPENDIX

.... ii

34 Fabric care chart

35 Protecting the environment

35 Declaration of conformity

35 Specifications

36 Cycle chart

8 Contents

DVDV47d 484 03022E-01 EN 20120710.indd Sec2:8 2012-07-10 _ 5:27:21 I

UNPACKING YOUR DRYER

Unpack your Dryer and inspect it for shipping damage. Make sure you have received all of the items

shown below. If your Dryer was damaged during shipping, or you do not have all of the items, contact

1-800-SAMSUNG (726-7864).

To prevent personal injury or strain, wear protective gloves whenever lifting or carrying the dryer.

Packing materials can be dangerous to children. Keep all packing material (plastic bags, polystyrene,

....... etc.) well out of childrens' reach

I Control panel

Top Cover

[ BACK]

Door

Filter

I Frame Front

Duct Exhaust

"Y'-connector Short inlet hose Rubber Washer Long inlet hose

DVDV476 484 03022E-01 EN 20120710.indd Sec3:9

installing your dryer 9

2012-07-10 _ 5:27:22 I

Tools needed

Pipe wrench

Pliers cutting knife {gas oNy) Nut drivers

Level Phillips Screwdriver Duct tape Wrench

BASIC REQUIRMENTS

Make sure you have everything necessary for proper installation

A GROUNDED ELECTRICAL OUTLET is required. See Electrical Requirements.

A POWER CORD for electric dryers (except in Canada).

GAS LINES (if installing a gas dryer). The gas lines must meet national and local codes.

EXHAUST SYSTEM - must be rigid metal or flexible stiff-walled metal exhaust ducting.

10 installing your dryer

DVDV47d 484 03022E-01 EN 20120710.indd Sec3:10 2012-07-10 _ 5:27:22 I

DUCTING REQUIREMENTS

Use a 4-inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct.

Do not use a smaller duct.

Ducts larger than 4 inches (10.2 cm) in diameter can cause increased lint accumulation.

Lint accumulation should be cleaned regularly.

If a flexible metal duct must be used, use the type with a stiff sheet metal wall. Do not use a flexible duct

with a thin foil wall. Serious blockage can result if the flexible metal duct is bent too sharply.

Never install any type of flexible duct in walls, ceilings, or other concealed spaces.

Keep the exhaust duct as straight and short as possible.

Secure joints with duct tape. Do not use screws.

Plastic flexible duct can kink, sag, be punctured, reduce airflow, extend drying times, and affect dryer

operation.

Exhaust systems longer than recommended can extend drying times, affect machine operation, and

may collect lint.

The exhaust duct should end with an exhaust hood with a swing-out damper to prevent back drafts and

the entry of wildlife. Never use an exhaust hood with a magnetic damper.

The hood should have at least 12 inches (30.5 cm) of clearance between the bottom of the hood and

the ground or other obstruction. The hood opening should point down.

Never install a screen over the exhaust outlet.

To avoid lint buildup, do not exhaust the dryer directly into a window well. Do not exhaust under a house

or porch.

If exhaust ductwork must run through an unheated area, the duct should be insulated and slope slightly

down towards the exhaust hood to reduce condensation and lint buildup.

Inspect and clean the interior of the exhaust system at least once a year. Unplug the power cord before

cleaning.

Check frequently to be sure the exhaust hood damper opens and closes freely.

Check once per month, and clean at least one time per year. Note: If clothes are not getting dry, then

check ducting for obstructions.

Do not exhaust dryer into any wall, ceiling, crawl space, or concealed space of a building, gas vent, or

any other common duct or chimney. This could create a fire hazard from lint expelled by the dryer.

Weather Hood Type

Use Onlyforshoat-runinsta,ation

4" (10.2 cm)

No. Of 90 ° elbows Rigid Metallic Flexible*

80 ft. (24.4 m) 41 ft. (12.4 m)

i 68 ft. (20.7 m) 37 ft. (11.2 m)

2 57 ft. (17.4 m) 33 ft. (10.1 m)

3 47ft. (14.3 m) 29ft. (8.8 m)

* Do not use non-metallic flexible duct.

2.5" (6.4 cm)

Rigid Metallic Flexible _

74 ft. (22.6 m) 33 ft. (10.1 m)

62 ft. (18.9 m) 29 ft. (8.8 m)

51 ft. (15.5 m) 25 ft. (7.6 m)

41 ft. (12.5 m) 21 ft. (6.5 m)

DVDV47d 484 03022E-01 EN 20120710.indd Sec3:ll

installing your dryer 11

2012-07-10 _ 5:27:22 I

If the new dryer is being installed into an existing exhaust system, you must

make sure:

• The exhaust system meets all local, state, and national codes.

• That a flexible plastic duct is not used.

• To Inspect and clean all lint buildup from inside the existing duct.

• The duct is not kinked or crushed.

• The exhaust hood damper opens and closes freely.

The static pressure in any exhaust system must not exceed 0.83 inches of water column, or be

less than 0.

This can be measured with the dryer running with a manometer at the point where the exhaust

duct connects to the dryer. A no-heat setting should be used. The dryer tumbler should be

empty and the lint filter clean.

IMPORTANT TO INSTALLER

Please read the following instructions carefully before installing the dryer. These instructions should be kept

for future reference.

Z_ Remove the door from all discarded appliances to avoid the danger of a child suffocating.

WARNINe

LOCATION CONSI DERATIONS

Locate the dryer where there is enough space at the front for loading the dryer, and enough space behind

for the exhaust system. This dryer is factory-ready for rear exhaust. To exhaust out the bottom or the right

or the left (electric model only), use the accessory exhaust kit (sold separately). Instructions are included

with the kit. It's important to make sure the room has enough fresh air. The dryer must be located where

there is no air-flow obstruction.

On gas dryers, adequate clearance as noted on the data plate must be maintained to ensure adequate air

for combustion and proper dryer operation.

Do not install or store the dryer in an area where it will be exposed to water and/or weather. Keep the dryer

area clear of combustible materials, casoline, and other flammable vapors and liquids. A dryer produces

combustible lint. The area around the dryer should be kept Lint-Free.

ALCOVE OR CLOSET INSTALLATION

Z_ You must exhaust the dryer to the outside to reduce the risk of fi re when installed in an alcove or

w,_.,._ closet.

• No other fuel-burning appliance should be installed in the same closet as the dryer.

• WARNING: To reduce the risk of fi re, you must exhaust the dryer to the outdoors.

See Exhaust information section.

• Minimum clearances between the dryer and adjacent walls or other surfaces are:

2" in front, 17" on top, 1" on either side, and 5" in the back.

• The closet front must have two unobstructed air openings for a combined minimum total area of 72 in2

with 3" minimum clearance on the top and bottom. A Iouvered door with equivalent space clearance is

acceptable.

12 installing your _dryer

DVDV47d 484 03022E-01 EN 20120710.indd Sec3:12 2012-07-10 vv 5:27:22 I

MOBILE HOME INSTALLATION

The installation of the dryer in mobile homes must conform to the Manufactured Home Construction and

Safety Standard Title 24 CFR, Part 3280 {formerly the Federal Standard for Mobile Home Construction and

Safety, Title 24, HUD (Part 280), 1975} for the United States) or CSA Standards Z240 (for Canada).

When installing a dryer in a mobile home, you must make provisions for anchoring the dryer to the floor.

Locate the dryer in an area that has adequate fresh air.

A minimum of 72 in2 (465 cm2) of unobstructed space is required.

Call 1-800-SAMSUNG(726-7864) for information on purchasing the Floor Anchoring Kit as an accessory.

All mobile home installations must be exhausted to the outside with the exhaust duct termination securely

fastened to the mobile home structure, using materials that wiii not support combustion.

The exhaust duct may not terminate underneath the mobile home.

See Exhausting section for more information.

EXHAUSTING

Exhausting the dryer to the outside will prevent large amounts of lint and moisture from being blown into the

room.

the United States:

All dryers must be exhausted to the outside.

The required exhaust duct is 4 inches (10.2 cm) in diameter.

Use only those foil-type flexible ducts, if any, specifically identified for use with the appliance

by the manufacturer and that comply with the Outline for Clothes Dryer Transition Duct,

Subject 2158A.

Do not assemble the duct with screws or other fastening means that extend into the duct

and catch lint.

In Canada:

• Use only those foil-type fl exible ducts, if any, specifically identified for use with the appliance

by the manufacturer.

• All dryers must be exhausted to the outside.

• The exhaust duct should be 4 inches (10.2 cm) in diameter.

Outside the U.S. and Canada:

• Refer to the local codes.

Z_ You must exhaust the dryer to the outside to reduce the risk of fi re when you install the

....... dryer in an alcove or closet.

NEVER USE A PLASTIC OR NON-METAL FLEXIBLE DUCT.

If your existing ductwork is plastic, non-metal, or combustible, replace it with metal.

Use only a metal exhaust duct that is non-flammable to ensure containment of exhaust air,

heat, and lint.

DVDV47d 484 03022E-01 EN 20120710.indd Sec3:13

installing your dryer 13

2012-07-10 _ 5:27:22 I

GAS REQUIREMENTS

Use only natural or LP (liquid propane) gases.

THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL

CODES, WITH THE NATIONAL FUEL GAS CODE ANSVZ223.1, LATEST REVISION (FOR THE UNITED

STATES), OR WITH THE CAN/CGA-B149 INSTALLATION CODES (FOR CANADA).

Gas dryers are equipped with a burner vent for use with natural gas. If you plan to use your dryer with LP

(liquid propane) gas, it must be converted for safe and proper performance by a qualified service technician.

A 1/2" (1.27 cm) gas supply line is recommended and must be reduced to connect to the 3/8" (1 cm) gas

line on your dryer. The National Fuel Gas Code requires that an accessible, approved manual gas shut-off

valve be installed within G" of your dryer.

Gas dryers installed in residential garages must be raised 18 inches (46 cm) above the floor.

Additionally, a 1/8" (0.3 cm) N.RT. (National Pipe Thread) plugged tapping, accessible for test gauge

connection, must be installed immediately upstream of your dryer's gas supply connection.

Your dryer must be disconnected from the gas supply pipe system during any pressure testing of the

system.

DO NOT reuse old flexible metal gas lines. Flexible gas lines must be design certified by the American Gas

Association (CGA in Canada).

, ny pipe joint compound used must be resistant to the action of any liquefied petroleum gas.

As a courtesy, most local gas utilities will inspect a gas appliance installation.

GAS IGNITION - Your dryer uses an automatic ignition system to ignite the burner.

There is no constant burning pilot.

COMMONWEALTH OF MASSACHUSETTS INSTALLATION

INSTRUCTIONS

Your dryer must be installed by a licensed plumber or gas fitter. A "T" handle manual gas valve must be

installed in the gas supply line to your dryer. If a flexible gas connector is used to install your dryer, the

connector can be no longer than 3' (36").

/_ * Gas leaks may occur in your system, creating a dangerous situation.

....... • Gas leaks may not be detected by smell alone.

Gas suppliers recommend you purchase and install a UL-approved gas detector.

Install and use in accordance with manufacturer's instructions.

14 installing your dryer

DVDV47d 484 03022E-01 EN 20120710.indd Sec3:14 2012-07-10 _ 5:27:22 I

ELECTRICAL REQUIREMENTS

[_ Wiring is located the below the control frame back.

diagram

plate panel

Z_* Improper connection of the equipment grounding conductor can result in a risk of electric shock.

....... Check with a qualified electrician or serviceman if you are in doubt as to whether your dryer is

properly grounded. Do not modify the plug provided with your dryer - if it doesn't fit the outlet,

have a proper outlet installed by a qualified electrician.

* To prevent unnecessary risk of fire, electrical shock, or personal injury, all wiring and grounding

must be done in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA No. 70-Latest Revision (for the U.S.) or the Canadian Electrical Code

CSA C22.1 - Latest Revisions and local codes and ordinances. It is your responsibility to provide

adequate electrical services for your dryer.

* All gas installations must be done in accordance with the national Fuel Code ANSI/Z2231 - Latest

Revision (for the U.S.) or CAN/CGA - B149 Installation Codes - Latest Revision (for Canada) and

local codes and ordinances.

GROUNDING

This dryer must be grounded. In the event of malfunction or breakdown, the ground will reduce the risk of

electrical shock by providing a path of least resistance for the electrical current.

Z_ Gas models

WARNING

Your dryer has a cord with an equipment-grounding conductor and a grounding plug.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

Do not modify the plug provided with your dryer - if it doesn't fit the outlet, have a proper outlet

installed by a qualified electrician.

Never connect the ground wire to plastic plumbing lines, gas lines, or hot water pipes.

WARNING

Electric models

Your dryer has a cord with an equipment-grounding conductor and a grounding plug, sold

separately.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

Do not modify the plug provided with your dryer - if it doesn't fit the outlet, have a proper outlet

installed by a qualified electrician.

If a power cord is not used and the electric dryer is to be permanently wired, the dryer must

be connected to a permanently grounded metal wiring system, or an equipment grounding

conductor must be run with the circuit conductors and connected to the equipment grounding

terminal.

DVDV47d 484 03022E-01 EN 20120710.indd Sec3:15

installing your dryer 15

2012-07-10 _m 5:27:23 I

ELECTRICAL CONNECTIONS

Before operating or testing, follow all grounding instructions in the Grounding section.

An individual branch (or separate) circuit serving only your dryer is recommended. DO NOT USE AN

EXTENSION CORD.

Gas models- U.S. and Canada

A 120 volt, 60 Hz AC approved electrical service, with a 15-ampere fuse or circuit breaker is

required.

Electric models- U.S. only

Most U.S. dryers require a 120 / 240 volt, 60 Hz AC approved electrical service. Some require

120 / 208 volt, 60 Hz approved electrical service. The electric service requirements can be found

on the data label located behind the door. A 30-ampere fuse or circuit breaker on both sides of

the line is required.

• If a power cord is used, the cord should be plugged into a 30-ampere receptacle.

• The power cord is NOT provided with U.S. electric model dryers.

IMPORTANT:

When local codes allow, the dryer electrical supply may be connected by means of a new power

supply cord kit, marked for use with a dryer, that is U.L. listed and rated at a minimum of120/240

volts, 30-ampere with three No. 10 copper wire conductors terminated with closed loop

terminals, open-end spade lugs with turned up ends, or with tinned leads.

• Do not reuse a power supply cord from an old dryer. The power cord electric supply wiring

must be retained at the dryer cabinet with a suitable UL-listed strain relief.

• Grounding through the neutral conductor is prohibited for (1) new branch-circuit installations,

(2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit

grounding through the neutral conductor. (Use 4-prong plug for 4 wire receptacle, NEMA

type 14-30R.)

Electric models - Canada Only

• A 120 / 240 volt, 60 Hz AC approved electrical service fused through a 30-ampere fuse or

circuit breaker on both sides of the line is required.

• All Canadian models are shipped with the power cord attached. The power cord should be

plugged into a 30-ampere receptacle.

_lt not permissible to convert a dryer to

is in Canada 2O8 volts.

16 installing your ' dryer

DVDV47d 484 03022E-01 EN 20120710.indd Sec3:16 2012-07-10 _ 5:27:23 I

INSTALLATION - GENERAL PROCEDURE

For proper installation, we recommend that you hire a qualified installer.

Read these instructions completely before you begin the installation.

To install the dryer, follow these steps:

1. Move your dryer to an appropriate location for installation. Consider installing the dryer and washer side-

by-side so you have easy access to both appliances.

To move the dryer easily, lay two of the carton cushion-tops on the floor. Tip your dryer on its side so it

lies across both cushion-tops. Push the dryer so that it is near its final location. Set your dryer upright.

Leave enough room around the dryer so you can attach the duct work, power cord, etc.

2. If you need to change the direction of the door, go to Door Reversal on page. When done, return to

Step 3 below.

3. Review the Exhausting section before installing the exhaust system. Install the duct work from your

dryer to the exhaust hood. The crimped end of the duct sections must point away from your dryer. DO

NOT use sheet metal screws when assembling ducting. These joints should be taped. Never use plastic

flexible exhaust material.

A tip for tight installations: Attach a section of the exhaust system to your dryer before putting it in

place. Use duct tape to secure this section to your dryer, but do not cover the ventilation slots at the

back of the dryer cabinet.

4. If you have an electric model, skip to Step 6. If you have a gas model, go to the next step.

5. Review the Gas Requirements section, then follow the lettered steps below.

a. Remove the pipe thread protective cap.

b. Apply pipe joint compound or about 1 1/2 wraps of Teflon tape over all threaded connections.

[_ The pipe joint compound must be resistant to the action of liquefied petroleum

any gas.

c. Connect the gas supply to your dryer. An additional fitting is required to connect the 3/4" (1.9 cm)

female thread end of a flexible connector to the 3/8" (1 cm) male threaded end on the dryer.

d. Securely tighten the gas line fitting over the threads.

e. Turn on the gas supply. Check all gas connections for leaks using a soap solution. If bubbles

appear, tighten the connections and recheck. DO NOT use an open flame to check for gas leaks.

f. Go to Step 6 on the next page

DVDV476 484 03022E-01 EN 20120710.indd Sec3:17

installing your dryer 17

2012-07-10 _ 5:27:23 I

6. Review the Electrical Requirements section, then follow the 3 Wire system connection instructions

(Step 7) or 4 Wire system instructions (Step 8) below.

7. Three Wire system instructions:

A° External ground connector

B° Neutral grounding wire (green/yellow)

¢. Center silver-colored terminal block screw

D. Neutral wire (white or center wire)

I_. r_A"(1.9 cm) UL-listed strain relief

t. Loosen or remove the center terminal block screw.

2. Connect the neutral wire (white or center wire) of the power

cord to the center, silver-colored terminal screw of the

terminal block. Tighten screw.

3. Connect the other wires to outer terminal block screws. Tighten screws.

4. Tighten the strain relief screws.

5. Insert the tab of the terminal block cover into your Dryer's rear panel slot.

Secure the cover with a hold-down screw.

If converting from a 4-wire electrical system to a 3-wire, you must connect the ground strap

_AR.,,_to the terminal block support to ground the dryer frame to the neutral conductor.

8°

We recommend using Ring terminals. If you use Strap terminals, please ensure you install

them perfectly.

System instructions:

External ground connector

Green or bare copper wire of power cord

r_A"(1.9 cm) UL-listed strain relief

Center silver-colored terminal block screw

Neutral Grounding wire (green/yellow)

Neutral wire (white or center wire)

t. Remove the External ground connector screw.

2. Connect the ground wire (green or unwrapped) of the

power cord to the external ground connector screw. If

you want to connect B (Green or bare copper wire of

power cord) to the Neutral Post without assembling with A

(cabinet ground), call the service technician.

3. Loosen or remove the center terminal block screw.

4. Connect the neutral wire (white or center wire) of the power cord and the appliance ground

wire (green with yellow stripes) under the central screw of the terminal block.

5. Connect the other wires to the outer terminal block screws. Tighten screws.

6. Tighten the strain relief screws.

7. Insert the tab of the terminal block cover into your Dryer's rear panel slot.

Secure the cover with a hold-down screw.

Four Wire

¢.

We recommend using Ring terminals. If you use Strap terminals, please ensure you install

them perfectly.

18 installing your' dryer

DVDV476 484 03022E-01 EN 20120710.indd Sec3:18 2012-07-10 _ 5:27:23 I

U.S. MODELS:

IMPORTANT - All U.S. models are designed for a 3-WIRE SYSTEM CONNECTION. The dryer frame is

grounded to the neutral conductor at the terminal block. A 4-WIRE SYSTEM CONNECTION is required for

new or remodeled construction, mobile homes, or if local codes do not permit grounding through neutral.

If you use the 4-wire system, you cannot ground the dryer frame to the neutral conductor at the terminal

block.

Remove the terminal block cover plate. Insert the power cord with a UL-listed strain relief through the hole

provided in the cabinet near the terminal block.

A strain relief must be used. Do not loosen the nuts already installed on the terminal block. Be sure they are

tight. Use a 3/8" (1cm) deep well socket.

9. Connect the Water Inlet Hose. For instructions, go to Connecting the

Inlet Hose on page Level

10. To ensure that the dryer provides optimal drying performance, it must

be level. To level the dryer, follow the lettered steps below:

ao Using a level, check if the dryer is level side to side and then front

to back.

bo If the dryer is not level, adjust the leveling feet on the bottom of

the dryer until the washer is level side to side and back to front.

Turning the feet clockwise retracts the feet. Turning the feet

clockwise loosens and extends them.

[_ To set the dryer to the same height as the washer, fully

retract the leveling feet by turning them counterclockwise,

then loosen the feet by turning them clockwise. Once

the dryer is the same height as the washer, follow the

directions above to level the dryer.

Leveling feet

Retract fully Then loosen

[_ djust the leveling feet only as much as necessary to level the dryer. Extending the leveling

feet more than necessary can cause the dryer to vibrate.

1t. Make sure all gas connections (on gas models), exhaust, and electrical connections are complete. Plug

in your dryer, and then check its operation by using the checklist below.

12. For GAS MODELS ONLY

The burner may not ignite initially due to air in the gas line. Allowing your dryer to operate on a heat

setting will purge the line. If the gas does not ignite within 5 minutes, turn your dryer off and wait 5

minutes. Be sure the gas supply to your dryer has been turned on. To confirm gas ignition, check the

exhaust for heat.

FINAL INSTALLATION CHECKLIST

[] The dryer is plugged into an electrical outlet and grounded properly.

[] The exhaust ductwork is hooked up and the joints are taped.

[] You have used rigid or stiff-walled flexible metal duct material, not plastic flexible duct.

[] The dryer is level and is sitting firmly on the floor.

[] For gas models: The gas is turned on and there are no gas leaks.

[] Start your dryer to confirm that it runs, heats, and shuts off.

DVDV47d 484 03022E-01 EN 20120710.indd Sec3:19

installing your dryer 19

2012-07-10 _ 5:27:23 I

CONNECTING THE INLET HOSE

Method1 - Using the Y Connector and Long Hose

The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old

hoses.

t. Turn off the cold water faucet. _ /

2. If you have a washer water hose attached to the cold water '1 _'_r"_ IY-C..... ,or

faucet, unscrew and remove the hose. _j<TL_--,_,

3. If space permits, attach the brass female end of the _,_

"Y"connector to the cold water faucet. Turn by hand until L_ -

tight 41

4. Attach the straight end of the long hose to the "Y' connector, water HOSe--S_%

Screw on the hose coupling by hand until it is tight.

DuctExhaust

5. Using pliers, tighten the hose coupling with an additional two_ Duo1 ' J

thirds turn. (_€__j___

r-_ Do not overtighten. You can damage the coupling. L"N_'_\ _ _ Frame

"_._\_ _ (back)

6. Attach the angled end of the long hose to the fill valve at the _'---_" _ I J

bottom of the dryer's rear frame. Screw on the coupling by f Z_' t I

hand until it is tight. _ -_'_ t t f'_

7. Using pliers, tighten the hose coupling with an additional two L-,/_ "-_ _ f /

thirds turn. f// .

. . / / _ Water Hose

L_ Do not overhghten. You can damage the couphng. / / /

8. Attach the water hose to the other side of the "Y" connector. Screw on the hose coupling until it

is tight. Using pliers, tighten the coupling with an additional two thirds turn.

{_Do not overtighten. You can damage the coupling.

9. Turn the water faucet on.

t0. Check for leaks around "Y" connector, faucets, and hoses.

20 installing your dryer

DVDV47d 484 03022E-01 EN 20120710.indd Sec3:20 2012-07-10 qv 5:27:23 I

Method2 - Using the Short Hose, Long Hose, and Y Connector

The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old

hoses.

If the "Y" connector cannot be attached directly to the cold water faucet, then you must use the

short hose.

1. Turn off the cold water faucet.

2. If you have a washer water hose attached to the cold water

faucet, unscrew and remove the hose.

3. Attach the short inlet hose to the cold water faucet. Screw

on the coupling by hand until it is tight.

4. Using pliers, tighten the coupling with an additional two

thirds turn.

Do not overtighten. You can damage the coupling.

5. Attach the 'Y" connector to the stainless male end of the

small hose. Screw on the coupling by hand until it is tight.

6. Using pliers, tighten the coupling with an additional two

thirds turn.

_Do overtighten, can damage coupling.

not You the

7. Attach the angled end of the long hose to the fill valve at the

bottom of the dryer rear frame. Screw on the coupling by

hand until it is tight.

8. Using pliers, tighten the coupling with an additional two

thirds turn.

_Do overtighten, can damage coupling.

not You the

9. Turn the water faucet on.

10. Check for leaks around "Y" connector, faucets, and hoses.

DVDV47d 484 03022E-01 EN 20120710.indd Sec3:21

installing your dryer 21

2012-07-10 vv 5:27:23 I

DRYER EXHAUST TiPS

Z_ Plastic or non-metal flexible duct presents a potential fire hazard.

WARNING

t. Make sure your dryer is installed properly so it exhausts air

easily.

2. Use 4" diameter rigid metal duct. Tape all joints, including at

the dryer.

Never use lint-trapping screws.

3. Keep ducts as straight as possible.

[ J

Clean all old ducts before installing your new dryer.

Be sure the vent flap opens and closes freely.

Inspect and clean the exhaust system annually.

Don't let a poor exhaust system slow drying by:

t. Restrict your dryer with a poor exhaust system. 1

2. Use a plastic, thin foil, or non-metal flexible duct.

3. Use unnecessarily long ducts that have many

elbows.

4. Use crushed or clogged vent or ducts.

22 installing your dryer

DVDV47d 484 03022E-01 EN 20120710.indd Sec3:22 2012-07-10 vv 5:27:23 I

DOOR REVERSAL

1. Unplug the power cord.

2. Remove the four hinge

screws from the door.

3. Remove the door by

lifting it.

4. Remove two Screws from

the Lever-Holder and then

remove two screws and

the Cover-Fronts on the

top and bottom of the

Frame-Front.

5. Remove two screws on

the Frame-Front and then

remove the screw and the

Cover-Holder on the right

of the Frame-Front.

6. After assembling the parts

removed in Step 4 into

the right of the Frame-

Front, tighten four screws.

7. Also after assembling

the parts removed in

Step 5 into the left of the

Frame-Front, tighten three

SCreWS.

8. Put the back of the parts

visible and remove the 15

SCreWS.

Remove the Holder-Glass

like a figure.

t0. First, the upper part of the

"A" component and "B"

please replace the parts

opposite each other.

(Remove two screws and

tighten two screws.)

t 1. Please replace the lower

regions equally.

t 2. If there have been placed

as shown, cover the

Holder-Glass.

t 3. Please install the Lever-

Door onto the other side

and tighten all the screws

remaining.

t4. Remove the Cushion-

Cover(F). Failure to do

so may result in the

malfunction.

(_ Store the removed

Cushion-Cover(F) in a

sale location. When you

change the direction in

which the door opens so

that the door opens to

the left, you have to install

the Cushion-Cover(F)

onto the door again.

t5. Install the door onto the

Frame-Front and tighten

the four screws that you

removed in Step 2.

i¸¸ ii!i¸

i.J?L,h

iiiiiiiiiiiiiiiiiill-y'_:_'<, Z

DVDV476 484 03022E-01 EN 20120710.indd Sec3:23

installing your dryer 23

2012-07-10 _ 5:27:23 I

OVERVIEW OF THE CONTROL PANEL

I I [] Sensor

cO @

Normal

HeavyDuty ._ Sanitize

PermPr Time Dry mveryo_ _ H_h _ 60_,,.

More_rl g Me_u_ u SOm_....

rowels .................. _ Air Fluff B Dal_p Dry ! Ex_a ow i 20nile. St e

Delkate _Refresh

Wool ..... -?.;._vJ .....................Winkle Away

_* Steam Cycles []

@ cO@@@@

i!ot! !i i!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!!!i iiiii!i ii!i!ii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

The display window shows the estimated time remaining in the cycle after you

have pressed the Start/Pause button. The estimated time remaining may fl

uctuate as the cycle progresses.

The Drying light will illuminate and remain lit until the cycle is complete.

When your dryer is in the cool-down phase, the Cooling light will illuminate. When

your dryer is in the wrinkle prevent phase, the Wrinkle Prevent light will illuminate.

When the cycle is complete, "END" will appear in the display panel until you

push the Start/Pause button or the Power button. If your dryer is paused during

a cycle, the indicator lights will blink until you press the Start/Pause button.

Adjust Time - You can add or subtract time from the automatically set times

in the Wrinkle Away cycle and the Manual Dry cycles (Time Dry, Quick Dry, or

Air Fluff cycles.)

To add or subtract time from the cycle, press the Adjust Time arrow pad up

or down until the desired time is displayed.

Wrinkle Prevent -Wrinkle Prevent provides approximately 180 minutes

of intermittent tumbling in unheated air at the end of the cycle to reduce

wrinkling. Press the Wrinkle Prevent button to activate this feature.

The indicator light above the pad will illuminate when you select Wrinkle Prevent.

The load is dry and you can remove it at any time during the Wrinkle Prevent cycle.

Rack Dry - Rack Dry is available at Time Dry cycle. Temperature will be set

only to Extra Low. (See page 28 for detail.)

Mixed Load Bell - The mixed load bell that notifies you when the average

dry level in a load is damp dry (80 % dried). This lets you take garments that

you don't want fully dried or that dry quickly out of the dryer early while letting

others continue to dry.

You can select this function in all Sensor Dry cycles except Wool and Sanitize.

The dry level selections are limited to Normal Dry, More Dry, and Very Dry.

Signal - When the cycle is complete, a chime will sound.

When you select the Wrinkle Prevent option, the chime will sound intermittently.

Adjust the volume of the chime or turn it off by pressing the Signal button.

Press the button repeatedly to scroll through the choices.

24 operating instructions, tips

DVDV47d 484 03022E-01 EN 20120710.indd 24 2012-07-10 vv 5:27:24 I

To select a cycle, rotate the Cycle Selector dial to the desired cycle.

The indicator light by the cycle name will illuminate. The Nomal, Heavy Duty,

Perm Press, Bedding, Towels, Delicates, Wool cycles are Sensor Dry cycles.

Sensor Dry automatically senses the moisture in the load and shuts the dryer

off when the load reaches the dryness level you have selected with the Dry

Level Selection Button (see below).

Normal - Use this cycle to dry loads of cotton, underwear, and linen.

Heavy Duty - Use this cycle to dry heavy fabrics such as jeans, corduroys, or

work clothes with high temperature heat.

Perm Press - Dry wrinkle-free cottons, synthetic fabrics, knits, and

permanent press fabrics automatically.

Bedding - For bulky items such as blankets, sheets and comforters.

Towels - To dry bath towels and similar items.

Delicates - The Delicates cycle is designed to dry heat-sensitive items at a

low drying temperature.

Wool - For machine washable and tumble dryable wool only.

Sanitize - Sanitizes garments by infusing high temperature heat deep into

the fabric during the drying cycle. Use this course to keep your bedding and

curtains clean through sanitization.

Time Dry - Time Dry allows you to select the desired cycle time in minutes.

Turn the Cycle Selector dial to Time Dry, then press the Adjust Time up arrow

to set the drying time. Press the arrow repeatedly to scroll through the time

settings.

Quick Dry - Provides a 30 minute drying cycle.

Air Fluff - The Air Fluff cycle tumbles the load at room temperature air.

Refresh - Use to smooth out wrinkles and reduce odors in loads of one to

four items. In this cycle a small amount of water is sprayed into the dryer

drum after several minutes of tumbling with heat.

Wrinkle Away - Reduce wrinkles in dry clothes that have been left in a

closet for a while by providing advanced wrinkle release performance through

optimized steam care. Reduced wrinkles in up to 3 items at a time.

You can change the drying time using the Adjust Time button.

You can increase or decrease the cycle time, but you cannot select a time

lower than the lowest pre-set automatic drying time (20 minutes).

You can set the drying time to 20 -e 30 _ 25 -e 33 in this order.

_lf you overload the dryer, you will get less than optimal results.

To select the dry level in the Normal, Heavy Duty, or other Sensor Dry cycles,

press the Dry Level button. An indicator light will illuminate next to the dryness

level you selected.

Press the button repeatedly to scroll through the settings. Larger or bulkier

loads may require the Very Dry or More Dry setting for complete dryness.

The Less Dry setting is best suited for lightweight fabrics or for leaving some

moisture in the clothing at the end of the cycle. Damp Dry is designed to

partially dry items. Use for items that lay flat or hang to dry.

DVDV47d 484 03022E-01 EN 20120710.indd Sec6:25

operating instructions, tips 25

2012-07-10 _ 5:27:24 I

iiiiiiiiiiiiililiiii!iii!i!i!!iiiii

iii!ii!ii ,

To select the temperature for the load, press the Temp button. An indicator

light will illuminate next to the temperature you selected. Press the button

repeatedly to scroll through the settings.

High - For sturdy cottons or those labeled Tumble Dry.

Medium - For permanent press, synthetics, lightweight cottons, or items

labeled Tumble Dry Medium.

Med Low - For heat lower than Medium. Use to dry synthetic or washable

knit fabrics.

Low - For heat sensitive items labeled Tumble Dry Low or Tumble Dry Warm.

Extra Low - Provides the lowest heated dry temperature possible.

When using Manual Dry cycles, you can adjust the drying time by pressing

the time selection button.

During the Sensory Dry cycle, the time light indicator is off because exact

drying times are determined by fluctuating humidity levels.

Press to pause and restart programs.

Press once to turn your dryer on, press again to turn it off. If you turn

your dryer on and do not touch any buttons for 10 minutes, the power

automatically turns off.

26 operating instructions, tips

DVDV47d 484 03022E-01 EN 20120710.indd Sec6:26 2012-07-10 vv 5:27:24 I

CHILD LOCK

A function to prevent children from playing with your dryer.

Setting/Releasing

If you want to set or release the Child Lock, )ress the Temp. and Time buttons simultaneously

for 3 seconds.

Child Lock Details

You can set Child Lock while your dryer is running.

Once you turn Child Lock on, no button, except for the Power button, will respond until you

release the Child Lock function.

The Child Lock indicator will be lit.

If you have not released Child Lock, and then turned the dryer off and on, the Child Lock

function will still be on. To release Child Lock, follow the instructions above.

When other buttons, except for the Power button, do not respond, check the Child Lock

indicator. If Child Lock is on, follow the instructions above to turn Child Lock off.

DRUM LIGHT

Lights the dryer drum while the dryer is running.

Turning On and Off

If you want turn on or turn off the Drum Light, press the Dry Level and Temp. buttons

simultaneously.

You can turn the Drum Light on and off while your dryer is running and when it is

stopped. If you do not turn the Drum Light off 5 minutes after turning it on, the Drum Light

automatically turns off.

DVDV47d 484 03022E-01 EN 20120710.indd Sec6:27

operating instructions, tips 27

2012-07-10 _ 5:27:24 I

op r t n tnA tion t

RACK DRY

Installing the drying rack

t. Open the dryer door.

2. Place the Drying Rack inside the product, and then align the holes of the filter handle of the

Drying Rack to the front projections.

3. Place the rear legs in the two recessed areas of the dryer's back wall, and then push down

the middle of the drying rack to fix it in place.

4. Place the items to be dried on the rack, leaving space between them so air can circulate.

5. Close the dryer door.

6. Press the RACK DRY button in Time Dry cycle, and then select the time according to the

moisture and weight of item.

Use the Time Dry cycle. Select the time according to the moisture and weight of the items.

Start the Dryer. it may be necessary to reset the timer if a longer time is needed.

}}

L,i _....">4:

_oor /

iii

Drying

Place the Drying Rack inside the dryer, align the holes of the filter handle of the Drying Rack

with the front projections, and then secure the back of the Drying Rack.

Washable sweaters

(block to shape and lay flat on rack)

Stuffed toys

(cotton or polyester fiberfilled)

Stuffed toys

(foam or rubber-filled)

Foam rubber pillows Air Fluff

Sneakers Air Fluff

Drying foam rubber, plastic, or rubber on a heat setting may cause damage to the items

....... and create a fire hazard.

[_ln case supplied Drying Rack, you can purchase through a

of Model is not it service center.

Extra Low (Time Dry cycle)

Air Fluff

28 operating instructions, tips

DVDV47d 484 03022E-01 EN 20120710.indd Sec6:28 2012-07-10 _ 5:27:25 I

CLEAN THE LINT FILTER

After each load.

To shorten drying time.

To operate more energy efficiently.

_Do not operate your dryer place.

without the lint filter in

Door

LOAD THE DRYER PROPERLY

Place only one washload in your dryer at a time.

In mixed loads, heavy and lightweight fabrics will dry differently. This may result in lightweight fabrics

being dry while heavy fabrics remain damp at the end of a drying cycle.

Add one or more additional similar items to your dryer when you are drying only one or two items. This

improves the tumbling action and drying efficiency.

Overloading restricts tumbling action, resulting in uneven drying as well as excessive wrinkling of some

fabrics.

GETTING STARTED

1. Load your dryer loosely- DO NOT overload.

2. Close the door.

3. Select the appropriate cycle and options for the load (see pages 24, 25, 26).

4. Press the Start/Pause button.

5. The dryer indicator light will illuminate.

6. The estimated cycle time will appear in the display.

The time may fluctuate as humidity levels fluctuate in the dryer.

. hen the cycle is complete, "End" will appear in the display.

Pressing Power cancels the cycle and stops your dryer.

The Drying, Cooling, and Wrinkle Prevent indicator lights will illuminate during those portions of the

cycle.

Do not place anything on top of your dryer while it is running.

WARNING

DVDV47d 484 03022E-01 EN 20120710.indd Sec6:29

operating instructions, tips 29

2012-07-10 vv 5:27:25 I

c re c na

CONTROL PANEL

Clean with a soft, damp cloth. Do not use abrasive substances.

Do not spray cleaners directly on the panel.

The control panel finish may be damaged by some laundry pre-treatment soil and stain remover products.

Apply such products away from your dryer and wipe up any spills or overspray immediately.

TUMBLER

Remove any stains such as crayon, ink, or fabric dye (from new items such as towels or jeans) with an all-

purpose cleaner.

Tumble old towels or rags to remove any excess stain or cleaning substance.

Once these steps are followed, stains may still be visible, but should not transfer to subsequent loads.

STAINLESS STEEL TUMBLER (DV476*)/POWDER COATED

TU M BLER (DV484")

To clean the stainless steel tumbler (DV476")/powder coated tumbler(DV484*), use a damp cloth with a

mild, non-abrasive cleaner suitable for stainless steel surfaces.

Remove the cleaner residue and dry with a clean cloth.

DRYER EXTERIOR

Clean with a soft, damp cloth. Do not use abrasive substances.

Protect the surface from sharp objects.

Do not place any heavy or sharp objects or a detergent box on the dryer. They can scratch or damage the

top cover of the dryer. Keep these items in the separately purchased pedestal or in a separate storage box.

The entire dryer has a high-gloss finish. Avoid scratching or damaging the surface when using the dryer.

DRYER EXHAUST SYSTEM

Inspect and clean the dryer exhaust system yearly to maintain optimum performance.

The outside exhaust hood should be cleaned more frequently to ensure proper operation.

30 care and cHeaning

DVDV47d 484 03022E-01 EN 20120710.indd 30 2012-07-10 vv 5:27:25 I

LAndrv

I J I

Special laundry tips

Please follow the care label or manufacturer's instructions for drying special

items. If care label instructions are not available, use the following information as

a guide.

Bedspreads & Comforters

Blankets

Curtains & Draperies

Cloth Diapers

Down-filled Items (jackets,

sleeping bags, comforters.

etc.)

Foam Rubber (rug backs,

stuffed toys, shoulder pads,

etc.)

Pillows

Plastics (shower curtains,

outdoor furniture covers,

etc.)

THINGS TO AVOID :

Follow the care label instructions or dry using the Bedding cycle.

Make sure the item is thoroughly dry before using or storing.

May require repositioning to ensure even drying.

Use the Normal cycle and dry only one blanket at a time for best

tumbling action.

Make sure the item is thoroughly dry before using or storing.

Use the Perm Press cycle and medium temperature to help minimize

wrinkling.

Dry these in small loads for best results and remove as soon as

possible.

Use the Normal cycle and the High temperature settings for soft,

fluffy diapers.

Use the Normal cycle and medium temperature setting.

Adding a couple of dry towels shortens drying time and absorbs

moisture.

DO NOT dry on a heat setting. Use the Air Fluff cycle (no heat).

WARNING - Drying a rubber item with heat may damage it or create

a fire hazard.

Use the Normal cycle.

Add a couple of dry towels and a pair of clean sneakers to help the

tumbling action and to fluff the item.

DO NOT dry kapok or foam pillows in the dryer. You can dry these

items in the dryer as long as you use the air fluff cycle.

Use the Air Fluff cycle or the Time Dry cycle and the Low or Extra

Low temperature settings depending on the care label instructions.

Fiberglass items (curtains, draperies, etc.).

Woolens, unless recommended on the label.

Items spotted or soaked with vegetable or cooking oils.

DVDV47d 484 03022E-01 EN 20120710.indd Secl0:31

special laundry tips 31

2012-07-10 vv 5:27:25 I

troL]beshootinG

CHECK THESE POINTS IF YOUR DRYER...

Doesn't run.

Doesn't heat.

Doesn't dry.

Is noisy.

Dries unevenly.

Has an odor.

Make sure the door is latched shut.

Be sure the power cord is plugged into a live electrical outlet.

Check your home's circuit breakers or fuses.

Press the Start/Pause button again ifthe door is opened during the

cycle.

Check your home's circuit breakers or fuses.

Select a heat setting other than Air Fluff.

On a gas dryer, check that the gas supply is on.

Clean the lint filter and exhaust duct.

Dryer may have moved into the cool-down phase of the cycle.

Check all of the above, plus...

Be sure the exhaust hood outside the home can open and close

freely.

Check the exhaust system for lint buildup. Ducting should be

inspected and cleaned annually.

Use a 4" rigid metal exhaust duct.

Do not overload. 1 wash load = 1 dryer load.

Sort heavy items from lightweight items.

o Large, bulky items like blankets or comforters may require

repositioning to ensure even drying.

Check that the washer is draining properly to extract adequate water

from the load.

Load may be too small to tumble properly. Add a few towels.

Check the load for objects such as coins, loose buttons, nails, etc.

Remove promptly.

It is normal to hear the dryer gas valve or heating element cycle on

and off during the drying cycle.

Be sure the dryer is leveled properly as outlined in the installation

instruction.

It is normal for the dryer to hum due to the high velocity of air moving

through the dryer drum and exhaust system.

Seams, pockets, and other similarly heavy areas may not be

completely dry when the rest of the load has reached the selected

dryness level. This is normal. Select the Very Dry setting if desired.

If one heavy item is dried with a lightweight load, such as one towel

with sheets, it is possible that the heavy item will not be completely

dry when the rest of the load has reached the selected dryness level.

Sort heavy items from lightweight items for best drying results.

Household odors from paint, varnish, strong cleaners, etc. may enter

the dryer with the surrounding room air. This is normal as the dryer

draws the air from the room, heats it, pulls it through the tumbler, and

exhausts it outside.

When these odors linger in the air, ventilate the room completely

before using the dryer.

32 troubleshooting

DVDV47d 484 03022E-01 EN 20120710.indd Sec5:32 2012-07-10 _ _ 5:27:25 I

Shuts off before load is dry •

Lint on clothes

Garments still wrinkled after

Wrinkle-Care

Odors remain in clothing

after Refresh.

Water drips from nozzle • This is steam condensation. The dripping water will stop after a short

when Steam-Care starts time.

Sprayed water is not visible • Sprayed water is difficult to see when the door is closed

during Steam-Care

INFORMATION CODES

Information codes may be displayed to help you understand what is occurring with your Dryer better.

The dryer load is too small. Add more items or a few towels and

restart the cycle.

The dryer load is too large. Remove some items and restart the dryer.

Make sure the lint filter is cleaned before every load. With some loads

that produce high amounts of lint, it may be necessary to clean the

filter during the cycle.

Some fabrics are lint producers (for example, a fuzzy white cotton

towel) and they should be dried separately from clothes that are lint

trappers (for example, a pair of lack linen pants).

Divide larger loads into smaller loads for drying

Check pockets thoroughly before washing and drying clothes.

Small loads of 1 to 4 items work best.

Load fewer garments. Load similar-type garments.

Fabrics containing strong odors should be washed in a normal cycle.

tE Clogged Lint Screen

Vent is restricted

HE Invalid heating Temp in running the

dryer

dE Running the dryer with door open

dF Door is not closing properly

Unit detects a button is being

)ressed for over 30secs or button is

stuck

Invalid power source Frequency

2E Electronic Control Problem

(Over Voltage Error)

AE Electronic Control Problem

Communication Error)

Clean the screen or vent.

If the problem continues, call for service.

Call for service.

Close the door and then restart.

If the problem continues, call for service.

Call for service.

Make sure a button is NOT being pressed

continuously. Try restarting the cycle.

If the problem continues, call for service.

Try restarting the cycle.

If the problem continues, call for service.

Call for service.

For any codes not listed above, call 1-800-726-7864 (1-800-SAMSUNG)

DVDV47d 484 03022E-01 EN 20120710.indd Sec4:33

troubleshooting 33

2012-07-10 _ 5:27:25 I

a.ppendx

FABRIC CARE CHART

The following symbols provide garment care directions. The Clothing care labels include symbols for

washing, bleaching, drying and ironing, or dry cleaning when necessary. The use of symbols ensures

consistency among garment manufacturers of domestic and imported items. Follow care label directions to

maximize garment life and reduce laundering problems.

iiii_i_i__?JJ__!!!!!i¸I_8_}_i_ _: il ¸i{ii_ __

!_ Normal

Permanent Press /

Wrinkle Resistant /

Wrinkle Control

Gentle/Delicates

HandWaah

• e_ Hot

Warm

• Cold

/b-q!ill

Any Bleach (when

needed)

Only Non-Chlorine

(color-sale)

Bleach (when needed)

Tumble Dry Cycle

Permanent Press/

Wrinkle Resistant/

Wrinkle Control

Gentle/Delicates

[]

Line Dry/Hang to Dry

Drip Dry

Dry Flat

High

Medium

Low

O Any Heat

No Heat/Air

High

Medium

Low

Do Not Wash

Do Not Wring

Do Not Bleach

Do Not Tumble Dry

No Steam (added to

iron)

Do Not Iron

O Dry Clean

Do Not Dry Clean

Line Dry/Hang to Dry

Drip Dry

[] Dry Flat

** The dot symbols represent appropriate wash water temperatures for various items. The temperature range

for Hot is 1050 - 125 °F / 41 o_ 52 °C, for Warm 850 - 105 °F / 290 - 41 °C and for Cold 60 ° - 85 °F /

16 ° - 29 °C. _/ash water temperature must be a minimum of 600 F/160 C for detergent activation and

effective cleaning.)

34 appendix

DVDV47d 484 03022E-01 EN 20120710.indd 34 2012-07-10 vv 5:27:25 I

PROTECTING THE ENVIRONMENT

This appliance is manufactured from recyclable materials. If you decide to dispose of this appliance, please

observe local waste disposal regulations. Cut off the power cord so that the appliance cannot be connected

to a power source. Remove the door so that animals and small children cannot get trapped inside the

appliance.

DECLARATION OF CONFORMITY

This appliance complies with UL2158.

SPECI FICATIONS

4...

" "C.

DIMENSIONS Div Inches (cm) Div Inches (cm)

A. Height

B.Width

WEIGHT

HEATER RATING

POWER NO HEAT

CONSUMPTION

HEATING

C. Depth with

44.8"(113.5)

door open 90 °

27"(68.6) D. Depth

125.5 Ib (57.0 kg)

5300 W (Elec.)

22000 BTU/hr (Gas)

49.6"(126.0)

29.4"(74.6)

268 W

5445 W (Elec.)

268 W (Gas)

DVDV47d 484 03022E-01 EN 20120710.indd Sec8:35

appendix 35

2012-07-10 _ 5:27:25 I

CYCLE CHART

EJec. Dryer Type

Heavy Duty

Perm Press

Bedding

Sensor Dry

Towels

Sanitize

Delicates

Wool

High

(Medium) Normal dry

High

(No change) Normal dry

Medium

(No change) Normal dry

High

(No change) Normal dry

High Normal dry

(Medium)

High Very dry

(No change) (No change)

Extra Low

(No change) Normal dry

Low Normal dry

(No change) (No change)

Air Fluff

(No chanqe)

High

Manual Cry Quick Dry (No change)

Time Dry High

High

Steam Wrinkle Away (Nochange)

Cycles High

(No change)

42 chin 39 chin 3 rain

58 min 55 min 3 Bin

32 min 29 min 3 min

50 min 47 min 3 min

60 min 55 min 5 min

34 min 33 min 1 min

21 min 20 min 1 min

20 min 20 min

30 min 27 min 3 min

40 min 37 min 3 min

20 min 19 min 1 min

15min 14min 1 min

180 min

Gas Dryer Type

Normal

Heavy Duty

Perm Press

Bedding

Sensor Dry

Towels

Sanitize

Delicates

, Wool

' Air Fluff

Manual Dry Quick Dr}'

Time Dr},

Wrinkle Away

Steam

cycles

High

(Medium) Normal dry

High Normal dry

(No change)

Medium

(No change) Normal dry

High Normal dry

(No change)

High Normal dry

(Medium)

High Very dry

(No change) (No change)

Extra Low

(No change) Normal dry

Low Normal dry

(No change) (No change)

(No change)

High

(No change)

High

(No change)

High

(No change)

42 min 39 min 3 rain

58 min 55 min 3 rain

32 min 29 min 3 min

50 min 47 min 3 min

60 min 55 min 5 min

34 min 33 min 1 rain 180 min

28 min 27 min 1 rain

20 min 20 min

30 min 27 min 3 min

40 min 37 min 3 min

20 min 19 min 1 min

15min 14min 1 min

36 appendix

DVDV47d 484 03022E-01 EN 20120710.indd Sec8:36 2012-07-10 7_ 5:27:25 I

SAMSUNG DRYER

LiMiTED WARRANTY TO ORiGiNAL PURCHASER

This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS AMERICA, INC.

(SAMSUNG) and delivered new, in the original carton to the original consumer purchaser, is warranted by

SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of:

One (1) Year All Parts and Labor

Two (2) Years Control Board Parts

This limited warranty begins on the original date of purchase, and is valid only on products purchased and

used in the United States.

To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service

procedures.

Warranty service can only be performed by a SAMSUNG authorized service center.

The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or

SAMSUNG's authorized service center.

SAMSUNG will provide in-home service during the warranty period at no charge, subject to availability

within the contiguous United States.

In-home service is not available in all areas.

To receive in-home service, product must be unobstructed and accessible to the service agent.

If service is not available, SAMSUNG may elect to provide transportation of the product to and from an

authorized service center.

SAMSUNG will repair, replace, or refund this product at our option and at no charge as stipulated herein,

with new or reconditioned parts or products if found to be defective during the limited warranty period

specified above.

All replaced parts and products become the property of SAMSUNG and must be returned to SAMSUNG.

Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is

longer.

This limited warranty covers manufacturing defects in materials and workmanship encountered in normal,

noncommercial use of this product and shall not apply to the following: damage that occurs in shipment;

delivew and installation; applications and uses for which this product was not intended; altered product or

serial numbers; cosmetic damage or exterior finish; accidents, abuse, neglect, fire, water, lightning, or other

acts of nature or God; use of products, equipment, systems, utilities, services, parts, supplies, accessories,

applications, installations, repairs, external wiring or connectors not supplied or authorized by SAMSUNG

that damage this product or result in service problems; incorrect electrical line voltage, fluctuations and

surges; customer adjustments and failure to follow operating instructions, maintenance and environmental

instructions that are covered and prescribed in the instruction book; product removal and reinstallation;

problems caused by pest infestations.

This limited warranty does not cover problems resulting from incorrect electric current, voltage or supply,

light bulbs, house fuses, house wiring, cost of a service call for instructions, or fixing installation errors.

SAMSUNG does not warrant uninterrupted or error-free operation of the product.

DVDV476 484 03022E-01 EN 20120710.indd 37

warranty 37

2012-07-10 _ _ 5:27:25 I

Except as set forth herein, there are no warranties on this product either express or implied, and samsung

disclaims all warranties including, but not limited to, any implied warranties of merchantability, infringement

or fitness for a particular purpose.

No warranty or guarantee given by any person, firm, or corporation with respect to this product shall be

binding on samsung.

Samsung shall not be liable for loss of revenue or profits, failure to realize savings or thter benefits, or any

other special, incidental or consequential damages caused by the use, misuse, or inability to use this

product, regardless of the legal theory on which the claim is based, and even if samsung has been advised

of the possibility of such damages.

Nor shall recovery of any kind against samsung be greater in amount than the purchase price of the product

sold by samsung and causing the alleged damage.

Without limiting the foregoing, purchaser assumes all risk and liability for loss, damage, or injury to

purchaser and purchaser's property and to others and their property arising out of the use, misuse,

or inability to use this product. This limited warranty shall not extend to anyone other than the original

purchaser of this product, is nontranderable and states your exclusive remedy.

Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation

of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This

warranty gives you specific rights, and you may also have other rights, which vary from state to state.

To obtain warranty service, please contact SAMSUNG at:

Samsung Electronics America, inc.

85 Challenger Road Ridgefield Park, NJ 07660

t-800-SAMSUNG (726-7864)

www.samsung.com

38 warranty

DVDV476 484 03022E-01 EN 20120710.indd 38 2012-07-10 _ _ 5:27:25 I

SAMSUNG DRYER

LiMiTED WARRANTY TO ORiGiNAL PURCHASER

This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS CANADA, INC.

(SAMSUNG) and delivered new, in the original carton to the original consumer purchaser, is warranted by

SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of:

One (1) year part and labor

This limited warranty begins on the original date of purchase, and is valid only on products purchased and

used in the Canada.

To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service

procedures.

Warranty service can only be performed by a SAMSUNG authorized service center.

The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or

SAMSUNG's authorized service center.

SAMSUNG will provide in-home service during the warranty period at no charge, subject to availability

within the Canada.