Titan 1140IX El manual del propietario

Marca: Titan

Modelo: 1140IX

Categoría: Rociador de pintura

Tipo: El manual del propietario

X-Lock Theft Deterrent System

Security Code

— — — —

Serial # _ _ _ _ _ _ _ _ _ _

Printed in the U. S. A.

Do not use this equipment before reading this manual!

1140ix Digital

Airless Sprayer

Owner’s Manual

For professional use only

NOTE: This manual

contains important

warnings and

instructions. Please

read and retain for

reference.

Model Number:

High Rider Bare 800-3030

High Rider Loaded 800-3035

Low Rider Bare 800-3040

Low Rider Loaded 800-3045

This symbol indicates a hazardous situation,

which, if not not avoided could result in death or

serious injury.

To reduce the risks of fire or explosion, electrical

shock and the injury to persons, read and under-

stand all instructions included in this manual. Be

familiar with the controls and proper usage of the

equipment.

HAZARD: INJECTION INJURY

A high pressure paint stream produced by this

equipment can pierce the skin and underlying

tissues, leading to serious injury and possible

amputation. See a physician immediately

DO NOT TREAT AN INJECTION INJURY AS A SIMPLE

CUT! Injection can lead to amputation. See a physician

immediately.

The maximum operating range of the sprayer is 3300 PSI / 22.8

MPa fluid pressure.

PREVENTION:

• NEVER aim the gun at any part of the body.

• Do not aim the gun at, or spray any person or animal.

• NEVER allow any part of the body to touch the fluid stream.

DO NOT allow body to touch a leak in the fluid hose.

• NEVER put your hand in front of the gun. Gloves will not

provide protection against an injection injury.

• ALWAYS lock the gun trigger, shut the pump off, and

release all pressure before servicing, cleaning the tip or

guard, changing tip, or leaving unattended. Pressure will

not be released by turning off the motor. The

PRIME/SPRAY valve or pressure bleed valve must be

turned to their appropriate positions to relieve system

pressure. Refer to the PRESSURE RELIEF

PROCEDURE described in this manual.

• ALWAYS keep the tip guard in place while spraying. The

tip guard provides some protection but is mainly a

warning device.

• ALWAYS remove the spray tip before flushing or cleaning

the system.

• Paint hose can develop leaks from wear, kinking and

abuse. A leak can inject material into the skin. Inspect

the hose before each use. Do not use hose to lift or pull

equipment.

• NEVER use a spray gun without a working trigger lock

and trigger guard in place.

• All accessories must be rated at or above 3300 PSI / 22.8

MPa. This includes spray tips, guns, extensions, and hose.

• Do not leave the unit energized or under pressure while

unattended. When the unit is not in use, turn off the unit

and relieve the pressure in accordance with the

PRESSURE RELIEF PROCEDURE described in this

manual.

• Verify that all connections are secure before operating the

unit. Unsecured parts may eject at great force or leak a

high pressure fluid stream causing severe injury.

• Always engage the trigger lock when not spraying. Verify

the trigger lock is functioning properly.

NOTE TO PHYSICIAN:

Injection into the skin is a traumatic injury. It is

important to treat the injury as soon as possible. DO

NOT delay treatment to research toxicity. Toxicity is a

concern with some coatings injected directly into the

blood stream. Consultation with a plastic surgeon or

reconstructive hand surgeon may be advisable.

HAZARD: HAZARDOUS VAPORS

Paints, solvents, insecticides, and other materials can

be harmful if inhaled or come in contact with the body

Vapors can cause severe nausea, fainting, or

poisoning.

PREVENTION:

• Use a respirator or mask if vapors can be

inhaled. Read all instructions supplied with the

mask to be sure it will provide the necessary

protection.

• W

ear protective eyewear.

• Wear protective clothing as required by coating

manufacturer.

HAZARD: EXPLOSION OR FIRE

Solvent and paint fumes can explode or ignite.

Property damage and/or severe injury can occur

PREVENTION:

• Provide extensive exhaust and fresh air introduction to

keep the air within the spray area free from accumulation

of flammable vapors. Solvent and paint fumes can

explode or ignite.

• Do not spray in a confined area.

• Avoid all ignition sources such as static electric

sparks, open flames, pilot lights, electrical

appliances, and hot objects. Connecting or disconnecting

power cords or working light switches can make sparks.

Paint or solvent flowing through the equipment is able to

result in static electricity.

• Do not smoke in spray area.

• Fire extinguisher must be present and in good working

order.

• Place pump at least 25 feet (7.62 meters) from the spray

object in a well ventilated area (add more hose if

necessary). Flammable vapors are often heavier than air.

Floor area must be extremely well ventilated. The pump

contains arcing parts that emit sparks and can ignite

vapors.

• The equipment and objects in and around the spray area

must be properly grounded to prevent static sparks.

• Keep area clean and free of paint or solvent containers,

rags and other flammable materials.

• Use only conductive or grounded high pressure fluid hose.

Gun must be grounded through hose connections.

• For electric units — power cord must be connected to a

grounded circuit.

• Always flush unit into a separate metal container, at low

pump pressure, with spray tip removed. Hold gun firmly

against side of container to ground container and prevent

static sparks.

• Follow the material and solvent manufacturer's warnings

and instructions. Know the contents of the paints and

solvents being sprayed. Read all Material Safety Data

Sheets (MSDS) and container labels provided with the

paints and solvents. Follow the paint and solvent

manufacturer’s safety instructions.

• Use extreme caution when using materials with a

flashpoint below 70ºF (21ºC). Flashpoint is the

temperature that a fluid can produce enough vapors to

ignite.

• Plastic can cause static sparks. Never hang plastic to

enclose a spray area. Do not use plastic drop cloths

when spraying flammable materials.

• Use lowest possible pressure to flush equipment.

• Do not spray onto pump assembly.

Important Safety Information • Read all safety information before

operating the equipment. Save these instructions.

HAZARD: EXPLOSION HAZARD DUE TO

INCOMPATIBLE MATERIALS

Will cause property damage or severe injury.

PREVENTION:

• Do not use materials containing bleach or chlorine.

• Do not use halogenated hydrocarbon solvents such as

bleach, mildewcide, methylene chloride and 1,1,1 -

trichloroethane. They are not compatible with aluminum.

• Contact your coating supplier about the compatibility of

material with aluminum.

HAZARD: GENERAL

Can cause severe injury or property damage.

•

Read all instructions and safety precautions before

operating equipment.

• Follow all appropriate local, state, and national codes

governing ventilation, fire prevention, and operation.

• The United States Government Safety Standards have

been adopted under the Occupational Safety and Health

Act (OSHA). These standards, particularly part 1910 of

the General Standards and part 1926 of the Construction

Standards should be consulted.

• Use only manufacturer authorized parts. User assumes

all risks and liabilities when using parts that do not meet

the minimum specifications and safety requirements of the

pump manufacturer.

• All hoses, fittings, and filter parts must be secured before

operating spray pump. Unsecured parts can eject at great

force or leak a high pressure fluid stream causing severe

injury.

• Before each use, check all hoses for cuts, leaks, abrasion

or bulging of cover. Check for damage or movement of

couplings. Immediately replace the hose if any of these

conditions exist. Never repair a paint hose. Replace it

with another grounded high-pressure hose.

• Do not kink or over-bend the hose. Airless hose can

develop leaks from wear, kinking and abuse. A leak can

inject material into the skin.

• Do not expose the hose to temperatures or pressures in

excess of those specified by manufacturer.

• Do not spray outdoors on windy days.

• Wear clothing to keep paint off skin and hair.

• Do not operate or spray near children. Keep children

away from the equipment at all times.

• Do not overreach or stand on an unstable support. Keep

effective footing and balance at all times.

• Use lowest possible pressure to flush equipment.

• Stay alert and watch what you are doing.

• Do not operate the unit when fatigued or under the

influence of drugs or alcohol.

• For electric units — Always unplug cord from outlet before

working on equipment.

• Do not use the hose as a strength member to pull or lift

the equipment.

• Do not lift by cart handle when loading or unloading.

Grounding Instructions

This product must be grounded. In the event of an electrical

short circuit, grounding reduces the risk of electric shock by

providing an escape wire for the electric current. This product

is equipped with a cord having a grounding wire with an

appropriate grounding plug. The plug must be plugged into an

outlet that is properly installed and grounded in accordance

with all local codes and ordinances.

Improper installation of the grounding plug

can result in a risk of electric shock.

If repair or replacement of the cord or plug is necessary, do not

connect the green grounding wire to either flat blade terminal.

The wire with insulation having a green outer surface with or

without yellow stripes is the grounding wire and must be

connected to the grounding pin.

Check with a qualified electrician or serviceman if the

grounding instructions are not completely understood, or if you

are in doubt as to whether the product is properly grounded.

Do not modify the plug provided. If the plug will not fit the

outlet, have the proper outlet installed by a qualified

electrician.

IMPORTANT: Use only a 3-wire extension cord that has a

3-blade grounding plug and a 3-slot receptacle that will

accept the plug on the product. Make sure your extension

cord is in good condition. When using an extension cord,

be sure to use one heavy enough to carry the current your

product will draw

. An undersized cord will cause a drop

in line voltage resulting in loss of power and overheating.

A 12 gauge cord is recommended. If an extension cord is

to be used outdoors, it must be marked with the suffix W-

A after the cord type designation. For example, a

designation of SJTW-A would indicate that the cord would

be appropriate for outdoor use.

IMPORTANT: When the sprayer is used with a generator

or uncontrolled line voltage, the use of Titan’s “Line Surge

Protector” (P/N 800-935) is recommended.

Specifications

Gallons per minute (GPM)...............1.2 (4.5 LPM)

Maximum tip sizes ...........................one gun = 0.034”

two guns = 0.023”

Maximum pressure ..........................3300 PSI (22.8 MPa)

Voltage .............................................100~120V AC, 50/60 Hz

Power................................................2.4 HP Infinity Plus

Brushless® DC Motor

Maximum current consumption........15 A

Weight..............................................95 lbs. (43.1 kg)

Maximum hose length......................300’ (91.4 m)

Grounded Outlet

Grounding Pin

Cover for grounded outlet box

Important Safety Information • Read all safety information before

operating the equipment. Save these instructions.

Table of Contents

Safety Precautions.................................................................2

Français ..............................................................................16

Español...............................................................................18

General Description ...............................................................4

Operation ................................................................................4

Setup ....................................................................................4

Preparing to Paint.................................................................5

Painting.................................................................................5

Control Panel Indicators .......................................................5

Xact Digital Control System Operation (if equipped)............6

Pressure Relief Procedure ...................................................7

Spraying ..................................................................................8

Spraying Technique ..............................................................8

Practice.................................................................................8

Cleanup ...................................................................................9

Maintenance............................................................................9

General Repair and Service Notes.......................................9

Replacing the Filters...........................................................10

Replacing the Motor Assembly...........................................10

Replacing the Gears ...........................................................11

Replacing the Transducer...................................................11

Replacing the PRIME/SPRAY Valve...................................12

Servicing the Fluid Section.................................................12

Troubleshooting ...................................................................14

Xact Digital Control System Error Messages .....................15

Parts Listings........................................................................20

Main Assembly....................................................................20

Drive Assembly...................................................................21

Fluid Section Assembly ......................................................22

High Rider Cart...................................................................23

Filter Assembly ...................................................................23

Low Rider Siphon Assembly...............................................24

Low Rider Cart....................................................................24

Labels .................................................................................24

PRIME/SPRAY Assembly ...................................................25

Electrical Schematic ...........................................................25

Accessories ........................................................................26

Warranty ................................................................................28

General Description

This airless sprayer is a precision power tool used for spraying

many types of materials. Read and follow this instruction

manual carefully for proper operating instructions,

maintenance, and safety information.

Operation

This equipment produces a fluid stream at

extremely high pressure. Read and understand

the warnings in the Safety Precautions section at

the front of this manual before operating this

equipment.

Return

Hose

Siphon

Tube

Pressure

Control

Knob

Control

Panel

Indicators

Xact Digital

Control

System

Fluid

Section

Filter

Motor

PRIME/

SPRAY

Valve

Outlet

Fitting

Setup

Perform the following procedure before plugging in the power

cord of an electric unit.

1. Ensure that the siphon tube and the return hose are

attached and secure.

2. Using a wrench, attach a minimum of 50’ of nylon airless

spray hose to the unit. Tighten securely.

3. Attach an airless spray gun to the spray hose. Using two

wrenches (one on the gun and one on the hose), tighten

securely.

Make sure all airless hoses and spray guns are

electrically grounded and rated at or above the

maximum operating pressure range of the airless

sprayer

4. Make sure the pressure control knob is in its OFF position

in the black zone.

Fill the oil cup with one tablespoon of piston seal lubricant

(Piston Lube).

IMPORTANT: Never operate unit for more than ten

seconds without fluid. Operating this unit without fluid

will cause unnecessary wear to the packings.

6. Make sure the electrical service is 120V, 15 amp

minimum.

Plug the power cord into a properly grounded outlet at

least 25’ from the spray area.

IMPORTANT: Always use a minimum 12 gauge, three-wire

extension cord with a grounded plug. Never remove the

third prong or use an adapter.

Preparing a New Sprayer

If this unit is new, it is shipped with test fluid in the fluid section

to prevent corrosion during shipment and storage. This fluid

must be thoroughly cleaned out of the system with mineral

spirits before you begin spraying.

IMPORTANT: Always keep the trigger lock on the spray

gun in the locked position while preparing the system.

1. Place the siphon tube into a container of mineral spirits.

2. Place the return hose into a metal waste container.

Set the pressure to minimum by turning the pressure

control knob to the “Min” setting in the yellow zone.

4. Move the PRIME/SPRAY valve down to

the PRIME position.

5. Turn on the sprayer by moving the

ON/OFF switch to the ON position.

6. Allow the sprayer to run for 15–30 seconds

to flush the test fluid out through the return

hose and into the waste container.

7. Turn off the sprayer by moving the ON/OFF switch to the

OFF position.

Min PSI

(Bar)

Max PSI

(Bar)

Blinking Yellow

0-200 PSI

Solid Yellow

201-1900 PSI

Solid Green

1901-3300 PSI

Motor Running

Pulse

Clean

Min. – 1900 PSI

(yellow zone)

1901 – 3300 PSI

(green zone)

Turbo PulseClean

(red zone)

OFF

(black

zone)

Pressure

Control Knob

NOTE: Do not attach the tip to the spray gun yet.

Remove the tip if it is already attached.

Preparing to Paint

Before painting, it is important to make sure that the fluid in the

system is compatible with the paint that is going to be used.

IMPORTANT: Always keep the trigger lock on the spray

gun in the locked position while preparing the system.

1. Place the siphon tube into a container of the appropriate

solvent. Examples of the appropriate solvent are water for

latex paint or mineral spirits for oil-based paints.

Place the return hose into a metal waste

container.

3. Set the pressure to minimum by turning

the pressure control knob to the “Min”

setting in the yellow zone.

4. Move the PRIME/SPRAY valve down to the

PRIME position.

5. Turn on the sprayer by moving the ON/OFF switch to the

ON position.

6. Allow the sprayer to run for 15–30 seconds to flush the old

solvent out through the return hose and into the metal

waste container.

7. Turn off the sprayer by moving the ON/OFF switch to the

OFF position.

8. Move the PRIME/SPRAY valve up to the

SPRAY position.

9. Turn on the sprayer.

10. Unlock the gun by turning the gun trigger

lock to the unlocked position.

Ground the gun by holding it

against the edge of the metal

container while flushing. Failure

to do so may lead to a static

electric discharge, which may

cause a fire.

11. Trigger the gun into the metal waste container until the old

solvent is gone and fresh solvent is coming out of the gun.

12.

Lock the gun by turning the gun trigger

lock to the locked position.

13. Set down the gun and increase the

pressure by turning the pressure control

knob slowly clockwise into the green

zone.

14. Check the entire system for leaks. If

leaks occur, follow the “Pressure Relief Procedure” in this

manual before tightening any fittings or hoses.

15. Follow the “Pressure Relief Procedure” in this manual

before changing from solvent to paint.

Be sure to follow the pressure relief procedure

when shutting down the sprayer for any purpose,

including servicing or adjusting any part of the

spray system, changing or cleaning spray tips, or

preparing for cleanup.

Trigger lock in

locked position.

NOTE: Make sure that the spray gun does not have a

tip or tip guard installed.

NOTE: Hold the return hose in the waste

container when moving the

PRIME/SPRAY valve to PRIME in

case the sprayer is pressurized.

Min PSI

(Bar)

Max PSI

(Bar)

Pulse

Clean

NOTE: Incompatible fluids and paint may cause the

valves to become stuck closed, which would

require disassembly and cleaning of the

sprayer’s fluid section.

Painting

1. Place the siphon tube into a container of paint.

2. Place the return hose into a metal waste

container.

3. Set the pressure to minimum by turning

the pressure control knob to the “Min”

setting in the yellow zone.

4. Move the PRIME/SPRAY valve down to the

PRIME position.

5. Turn on the sprayer by moving the ON/OFF

switch to the ON position.

6. Allow the sprayer to run until paint is

coming through the return hose into the

metal waste container.

7. Turn off the sprayer by moving the ON/OFF switch to the

OFF position.

8. Remove the return hose from the waste container and

place it in its operating position above the container of

paint.

9. Move the PRIME/SPRAY valve up to the

SPRAY position.

10. Turn on the sprayer.

11. Unlock the gun by turning the gun trigger

lock to the unlocked position.

Ground the gun by holding it

against the edge of the metal

container while flushing. Failure

to do so may lead to a static

electric discharge, which may

cause a fire.

12. Trigger the gun into the metal waste container until all air

and solvent is flushed from the spray hose and paint is

flowing freely from the gun.

13. Lock the gun by turning the gun trigger

lock to the locked position.

14. Turn off the sprayer

15. Attach tip guard and tip to the gun as

instructed by the tip guard or tip manuals.

POSSIBLE INJECTION HAZARD.

Do not spray without the tip guard

in place. Never trigger the gun

unless the tip is in either the spray or the unclog

position.

Always engage the gun trigger lock

before removing, replacing or cleaning tip.

16. Turn on the sprayer.

17. Increase the pressure by turning the pressure control knob

slowly clockwise toward the green zone and test the spray

pattern on a piece of cardboard. Adjust the pressure

control knob until the spray from the gun is completely

atomized. Try to keep the pressure control knob at the

lowest setting that maintains good atomization.

Control Panel Indicators

The following is a description of the control panel indicators.

Min PSI

(Bar)

Max PSI

(Bar)

Blinking Yellow

0-200 PSI

Solid Yellow

201-1900 PSI

Solid Green

1901-3300 PSI

Motor Running

Pulse

Clean

Pressure

Indicator

Motor Running

Indicator

NOTE: Turning the pressure up higher then needed to

atomize the paint will cause premature tip wear

and additional overspray.

Trigger lock in

locked position.

Min PSI

(Bar)

Max PSI

(Bar)

Pulse

Clean

Pressure Indicator

The pressure indicator shows the current operating pressure of

the sprayer. It has three different indications: blinking yellow,

solid yellow, and solid green.

Blinking Yellow

When the pressure indicator is blinking yellow, the sprayer is

operating between 0 and 200 PSI. A blinking yellow pressure

indicator means:

• The sprayer is plugged in and turned “ON”.

• The sprayer is at priming pressure (little or no pressure).

• It is safe to move the PRIME/SPRAY valve between

positions.

• It is safe to change or replace the spray tip.

Solid Yellow

When the pressure indicator is solid yellow, the sprayer is

operating between 200 and 1800 PSI.

A solid yellow pressure

indicator means:

• The sprayer is at the proper pressure setting for spraying

stain, lacquer, varnish, and multi-colors.

• If the pressure indicator goes to solid yellow when the

pressure is set so that it starts at solid green, it indicates

one of the following:

a. Tip Wear Indicator — when spraying with latex or at

high pressure the solid yellow appears. This means

the tip is worn and needs to be replaced.

b. Tip Too Large — when a tip that is too large for the

sprayer is put in the gun, the pressure indicator will turn

from solid green to solid yellow.

c. Fluid Section Wear — if a solid yellow pressure

indicator appears when using a new tip and the

pressure is set at maximum, service may be required

(worn packings, worn piston, stuck valve, etc...).

Solid Green

When the pressure indicator is solid green, the sprayer is

operating between 1800 and 3300 PSI.

A solid green pressure

indicator means:

• The sprayer is at the proper pressure setting for spraying

oil-based and latex house paints.

• The sprayer is operating at peak performance at a high

pressure setting.

Motor Running Indicator

The Motor Running indicator is on when the motor is

commanded to run. This indicator is used by service centers

to troubleshoot motor problems.

Xact Digital Control System Operation

(if equipped)

The Xact Digital Control System is an optional add-on that

increases the functionality of the sprayer. It is installed directly

below the pressure control knob on the control panel. It consists

of a display and four function keys. The display shows various

menu screens that allow the user to customize and monitor

sprayer operation using the function keys.

SET PSI 3000

ACTUAL PSI 2950

MENU +–SELECT

4321

Display

Function

Keys

NOTE: If the pressure indicator begins blinking yellow

when the pressure control knob is set at a

higher pressure and the PRIME/SPRAY valve is

in the SPRAY position, either the spray tip is

worn or the sprayer is in need of service/repair.

Function Keys

The function keys are numbered 1–4. Each key is labeled with

an additional function as well.

#1/Menu Key

Pressing the #1 key scrolls through the available menu

screens or performs a function described on the active menu

screen.

#2/+ Key

Pressing the #2 key performs a function described on the

active menu screen or increases a value.

#3/- Key

Pressing the #3 key performs a function described on the

active menu screen or decrease a value.

#4/Select Key

Pressing the #4 key selects the active menu screen or

performs a function described on the active menu screen.

Menu Screens

Several menu screens are available for the user to customize

and monitor sprayer operation. They include Main Screen,

User Pre-Sets, Volume Pumped, Job Volume, Unit Serial #,

TImers, Job Timers, Service Time, Pressure, Security Code,

Prime, and Pulse Clean.

Main Screen

The Main Screen is the default

screen for the control system

at sprayer startup. Pressing the #2 key switches between PSI

and MPa units of measure. Press the #1 key to scroll through

the remaining menu screens.

User Pre-Sets Screen

The User Pre-Sets screen

allows the user to set four

different pressure settings and save them for future use. To

select the User Pre-Sets screen, press the #4 key.

Press keys 1 through 4 from

the Select screen to select or

change a pre-set pressure.

Press the #4 key to select the

setting and the Main Screen

will appear.

Press the #2 key to change

the setting. On the following

screen, use the #2/+ key to

increase the setting or the #3/- screen to decrease the setting.

Once the desired setting has been reached, press the #4 key

to set and the Main Screen will appear. To select or change

the remaining three pre-sets, scroll to the User Pre-Sets

screen and repeat the above procedure.

Volume Pumped Screen

The Volume Pumped screen

shows the total number of

gallons or liters sprayed by the

sprayer

To select the Volume Pumped

screen, press the #4 key.

Job Volume Screen

The Job Volume screen allows

the user to reset a gallon

counter to track usage on

specific jobs.

o select the Job Volume

screen, press the #4 key.

JOB GALLONS XXXX

MENU-1 RESET-3

JOB VOLUME

SELECT-4 MENU-1

GALLONS XXXXXX

PRESS 1 FOR MENU

VOLUME PUMPED

SELECT-4 MENU-1

PRE-SET #1 750

PRESS +/- TO CHG

PSI SETTING 750

SELECT-4 CHG-2

SELECT

PRE-SETS 1-4

USER PRE-SETS

SELECT-4 MENU-1

SET PSI 3000

ACTUAL PSI 2950

NOTE: The pressure control knob overrides the Xact

Digital Control System settings. Anytime the

pressure control knob is turned, the sprayer

pressure will change accordingly.

Unit Serial # Screen

The Unit Serial # screen

shows the sprayers serial

number

To select the Unit Serial #

screen, press the #4 key.

Timers Screen

The Timers screen shows the

total time the sprayer has been

turned on as well as the total

time the sprayer has been running (pumping).

To select the

Timers screen,

press the #4 key.

Job Timers Screen

The Job Timers screen allows

the user to reset the “ON

TIME” and “RUN

TIME” to

track time on specific jobs.

To select the Job TImers

screen, press the #4 key. The

screen will toggle between the

timers and a screen that allows the user to reset the timers.

Service Time Screen

The Service Time screen

allows the user to set a service

time interval (in hours). Below

the set time, the screens shows the current amount of hours

on the sprayer

. To select the Service TImer screen, press the

#4 key.

The screen will toggle between

the service hours and a screen

that allows the user to change

the service time interval.

When the service time interval is set and met by the run hours,

the display will toggle between the "Main screen" and a

"Service Required" screen at sprayer startup. To stop the

toggling, scroll to the "Service Time" screen and either set a

new service time interval or set the service time to "0".

Pressure Screen

The Pressure screen allows

the user to see the current set

point pressure as well as the

actual working pressure.

o select the Pressure screen,

press the #4 key. This screen

is also the Main Screen.

Security Code Screen

The Security Code screen

allows the user to set a four

digit security code to prevent

unauthorized use of the sprayer. If a security code has been

set, the control system display will ask for the code at startup.

If the correct code is entered, the display will show the Main

Screen and the sprayer will operate. If the wrong code is

entered, the display will continue to ask for the correct code

and the sprayer will be disabled. To set or change the security

code, press the #2 key.

Enter the old security code

number to access the screen

that allows the code change.

If the wrong code is entered, the display will continue to ask

for the correct code and the security code cannot be changed.

ENTER OLD CODE

NUMBER

NOTE: If the sprayer is new, no security code is set

and the Main Screen will appear at startup.

Also, when setting a security code for the first

time, the “Enter Old Code Number” screen will

not appear.

SECURITY CODE

SELECT-4 MENU-1

SET PSI 3000

ACTUAL PSI 2950

PRESSURE

SELECT-4 MENU-1

SERVICE @ XXXHR

RUN HOURS XX

SERVICE TIME

SELECT-4 MENU-1

ON TIME XXXXX:XX

RUN TIME XXXX:XX

JOB TIMERS

SELECT-4 MENU-1

ON TIME XXXXX:XX

RUN TIME XXXX:XX

TIMERS

SELECT-4 MENU-1

SER # XXXXXXXXXX

PRESS 1 FOR MENU

UNIT SERIAL #

SELECT-4 MENU-1

Enter the new security code.

Once the new code is entered,

the display will automatically

ask that the new code be re-entered for verification. If the

same new code is re-entered, the display will confirm that the

new code has been accepted and return to the Main Screen.

If the new code is re-entered incorrectly, the display will return

to the “Enter New Code Number” screen and the process will

repeat.

Prime Screen

The Prime screen appears

when the pressure control

knob is set at the “Min” setting

in the yellow zone.

Pulse Clean Screen

The Pulse Clean screen

appears when the pressure

control knob is set at the

PULSE CLEAN position in the red zone and the

PRIME/SPRA

Y valve is in the PRIME position.

Pressure Relief Procedure

Be sure to follow the pressure relief procedure

when shutting the unit down for any purpose,

including servicing or adjusting any part of the

spray system, changing or cleaning spray tips, or

preparing for cleanup.

1. Lock the gun by turning the gun trigger

lock to the locked position.

Turn off the sprayer by moving the

ON/OFF switch to the OFF position.

3. Turn the pressure control knob

counterclockwise to its OFF position in

the black zone.

4. Unlock the gun by turning the gun trigger lock to the

unlocked position.

5. Hold the metal part of the gun firmly to

the side of a metal container to ground

the gun and avoid a build up of static

electricity.

6. Trigger the gun to remove any pressure

that may still be in the hose.

7. Lock the gun by turning the gun trigger lock

to the locked position.

8. Move the PRIME/SPRAY valve down to the

PRIME position.

Trigger lock in

locked position.

NOTE: If there is no action at any menu screen for 30

seconds, the display will go back to the Main

Screen.

PULSE CLEAN

ACTUAL PSI XXXX

PRIME

NOTE: To inactivate the X-Lock security function,

enter “1111” at the “Enter New Code Number”

screen (this is the default code that leaves the

sprayer unlocked). As a result, the Main

Screen will appear at sprayer startup.

ENTER NEW CODE

NUMBER

Spraying

POSSIBLE INJECTION HAZARD. Do not spray

without the tip guard in place. Never trigger the

gun unless the tip is in either the spray or the

unclog position. Always engage the gun trigger

lock before removing, replacing, or cleaning tip.

Spraying Technique

The following techniques, if followed, will assure professional

painting results.

Hold the gun perpendicular to the surface and always at equal

distance from the surface. Depending on the type of material,

surface, or desired spray pattern, the gun should be held at a

distance of 12 to 14 inches (30 to 35 cm).

Move the gun either across or up and down the surface at a

steady rate. Moving the gun at a consistent speed conserves

material and provides even coverage. The correct spraying speed

allows a full, wet coat of paint to be applied without runs or sags.

Holding the gun closer to the surface deposits more paint on

the surface and produces a narrower spray pattern. Holding

the gun farther from the surface produces a thinner coat and

wider spray pattern. If runs, sags, or excessive paint occur,

change to a spray tip with a smaller orifice. If there is an

insufficient amount of paint on the surface or you desire to

spray faster, a larger orifice tip should be selected.

Maintain uniform spray stroke action. Spray alternately from

left to right and right to left. Begin movement of the gun before

the trigger is pulled.

Avoid arcing or holding the gun at an angle. This will result in

an uneven finish.

Too Thick

Offspray

Arcing Gun at angle

start

stroke

release

trigger

pull

trigger

end

stroke

Proper lapping (overlap of spray pattern) is essential to an

even finish. Lap each stroke. If you are spraying horizontally,

aim at the bottom edge of the preceding stroke, so as to lap

the previous pattern by 50%.

For corners and edges, split the

center of the spray pattern on the

corner or edge and spray vertically

so that both adjoining sections

receive approximately even

amounts of paint.

When spraying with a shield, hold it firmly against the surface.

Angle the spray gun slightly away from the shield and toward

the surface. This will prevent paint from being forced

underneath.

Shrubs next to houses should be tied back and covered with a

canvas cloth. The cloth should be removed as soon as possible.

Titan gun extensions are extremely helpful in these situations.

Nearby objects such as automobiles, outdoor furniture, etc.

should be moved or covered whenever in the vicinity of a

spray job. Be careful of any other surrounding objects that

could be damaged by overspray.

Practice

1. Make sure that the paint hose is free of kinks and clear of

objects with sharp cutting edges.

3. Set the pressure to minimum by turning the pressure

control knob to the “Min” setting in the yellow zone.

3. Move the PRIME/SPRAY valve up to its SPRAY position.

4. Turn the pressure control knob clockwise to its highest

setting in the green zone. The paint hose should stiffen

as paint begins to flow through it.

5. Unlock the gun trigger lock.

6. Trigger the spray gun to bleed air out of the hose.

7. When paint reaches the spray tip, spray a test area to

check the spray pattern.

8. Use the lowest pressure setting

necessary to get a good spray

pattern. If the pressure is set too

high, the spray pattern will be too

light. If the pressure is set too

low, tailing will appear or the paint

will spatter out in gobs rather than

in a fine spray.

Good spray pattern

Paint tailing pattern

Overlap edges

1st

pass

2nd

pass

3rd

pass

4th

pass

5th

pass

Cleanup

Special cleanup instructions for use with

flammable solvents:

• Always flush spray gun preferably outside and at least one

hose length from spray pump.

• If collecting flushed solvents in a one gallon metal

container, place it into an empty five gallon container, then

flush solvents.

• Area must be free of flammable vapors.

• Follow all cleanup instructions.

IMPORTANT: The sprayer, hose, and gun should be

cleaned thoroughly after daily use. Failure to do so

permits material to build up, seriously affecting the

performance of the unit.

Always spray at minimum pressure with the gun

nozzle tip removed when using mineral spirits or

any other solvent to clean the sprayer, hose, or

gun. Static electricity buildup may result in a fire

or explosion in the presence of flammable vapors.

1. Follow the “Pressure Relief Procedure” found in the

Operation section of this manual.

Remove the gun tip and tip guard and clean with a brush

using the appropriate solvent.

3. Place the siphon tube into a container of the appropriate

solvent. Examples of the appropriate solvent are water for

latex paint or mineral spirits for oil-based paints.

4. Place the return hose into a metal waste container.

5. Move the PRIME/SPRAY valve down to its

PRIME position.

6. Set the pressure to Turbo PulseClean by

turning the pressure control knob to its

PULSE CLEAN position in the red zone.

7. Turn on the sprayer by moving the ON/OFF

switch to the ON position.

8. Allow the solvent to circulate through the unit and flush the

paint out of the return hose into the metal waste container.

9. Turn off the sprayer by moving the

ON/OFF switch to the OFF position.

10. Move the PRIME/SPRAY valve up to its

SPRAY position.

11. Turn on the sprayer.

Ground the gun by holding it

against the edge of the metal

container while flushing. Failure to

do so may lead to a static electric

discharge, which may cause a fire.

12. Trigger the gun into the metal waste container until the

paint is flushed out of the hose and solvent is coming out

of the gun.

13. Continue to trigger the spray gun into the waste container

until the solvent coming out of the gun is clean.

14.

Follow the “Pressure Relief Procedure” found in the

Operation section of this manual.

15. Unplug the sprayer and store in a clean, dry area.

IMPORTANT: Do not store the unit under pressure.

NOTE: For long-term or cold weather storage, pump

mineral sprits through the entire system.

For short-term storage when using latex paint,

pump water mixed with Titan Liquid Shield Plus

through the entire system (see the Accessories

section of this manual for part number).

Min PSI

(Bar)

Max PSI

(Bar)

Pulse

Clean

NOTE: Hold the return hose in the waste

container when moving the

PRIME/SPRAY valve to PRIME in

case the sprayer is pressurized.

Maintenance

Before proceeding, follow the Pressure Relief

Procedure outlined previously in this manual.

Additionally, follow all other warnings to reduce

the risk of an injection injury, injury from moving

parts or electric shock. Always unplug the

sprayer before servicing!

General Repair and Service Notes

The following tools are needed when repairing this sprayer:

Phillips Screwdriver 3/8" Hex Wrench

Needle Nose Pliers 5/16" Hex Wrench

Adjustable Wrench 1/4" Hex Wrench

Rubber Mallet 3/16" Hex Wrench

Flat-blade Screwdriver 5/32” Hex Wrench

1. Before repairing any part of the sprayer, read the

instructions carefully, including all warnings.

IMPORTANT: Never pull on a wire to disconnect it. Pulling

on a wire could loosen the connector from the wire.

2. Test your repair before regular operation of the sprayer to

be sure that the problem is corrected. If the sprayer does

not operate properly

, review the repair procedure to

determine if everything was done correctly. Refer to the

Troubleshooting Charts to help identify other possible

problems.

3. Make certain that the service area is well ventilated in

case solvents are used during cleaning. Always wear

protective eyewear while servicing. Additional protective

equipment may be required depending on the type of

cleaning solvent. Always contact the supplier of solvents

for recommendations.

4. If you have any further questions concerning your TITAN

Airless Sprayer, call TITAN:

Customer Service (U.S.) .......................1-800-526-5362

Fax ................................................1-800-528-4826

Customer Service (Canada)..................1-800-565-8665

Fax ................................................ 1-905-856-8496

Customer Service (International)...........1-201-337-1240

Fax ................................................1-201-405-7449

Replacing the Filters

Pump Filter

1. Loosen and remove the filter

body by hand.

2. Slip the filter off of the core

spring.

3. Inspect the filter. Based on

inspection, clean or replace

the filter.

4. Inspect the o-ring. Based on

inspection, clean or replace

the o-ring.

5. Slide the new or cleaned

filter over the core spring

with the filter spring adapter

in place. Push the filter into

the center of the filter

housing.

6. Slide the filter body over the

filter and thread it into the

filter housing until secure.

Gun Filter

1. Move the gun trigger lock to the unlocked position.

2. Loosen and remove the handle from the gun body.

3. Turning clockwise, unscrew the filter from the gun body.

4. Turning counterclockwise, screw the new or cleaned filter

into the gun body.

5. Make sure the handle seal is in position and thread the

handle into the gun body until secure.

6. Move the gun trigger lock to the locked position.

NOTE: For more detail, part number information, and

complete assembly drawings, please see the

LX-80

Professional Airless Gun Owner's

Manual (P/N 313-2293).

Handle

Seal

Filter

Gun

Body

NOTE: Left-handed threads require turning the filter

clockwise to remove.

NOTE: The filter body

should be hand-

tightened, but make

sure it is seated

fully into the filter

housing.

Filter Body

Filter Spring

Adapter

Core Spring

Filter

O-ring

Filter Housing

Replacing the Motor Assembly

1. Unplug the unit.

2. Loosen and remove the four motor shroud screws.

Remove the motor shroud.

3. Release the tie wrap on the top of the baffle assembly and

slip the baffle assembly down off of the motor.

4. Loosen and remove the three electronic cover screws.

Lift the electronic cover off of the electronic control

assembly on the motor.

5. Disconnect all wires between the motor and the sprayer.

6. Loosen and remove the three motor mounting screws.

7. Pull the motor out of the gearbox housing.

8. With the motor removed, inspect the gears in the gearbox

housing for damage or excessive wear. Replace the

gears, if necessary.

9. Install the new motor into the gearbox housing. Make

sure the housing gasket is positioned properly.

10. Secure the motor with the three motor mounting screws.

11. Reconnect the wires between the sprayer and the new

motor. (refer to the electrical schematic in the Parts List

section of this manual).

12. Position the electronic cover over the electronic control

assembly. Secure the electronic cover with the three

electronic cover screws.

13. Slip the baffle assembly up and around the motor. Secure

the baffle assembly with the tie wrap.

14. Slide the motor shroud over the motor. Make sure the

shroud gasket is positioned properly.

15. Secure the motor shroud with the four motor shroud

screws.

Electronic Cover

Motor Shroud

Motor Shroud Screws

Motor

Baffle Assembly

Housing Gasket

Shroud Gasket

Electronic Control

Assembly

Motor Mounting

Screw

Electronic Cover

Screw

Gearbox

Housing

Replacing the Gears

1. Unplug the unit.

2. Loosen and remove the four motor shroud screws.

Remove the motor shroud.

3. Release the tie wrap on the top of the baffle assembly and

slip the baffle assembly down off of the motor.

4. Loosen and remove the three electronic cover screws.

Lift the electronic cover off of the electronic control

assembly on the motor.

5. Disconnect all wires between the motor and the sprayer.

6. Loosen and remove the three motor mounting screws.

7. Pull the motor out of the gearbox housing.

8. Inspect the armature gear on the end of the motor for

damage or excessive wear. If this gear is completely

worn out, replace the front end bell assembly.

9. Remove and inspect the 1st stage gear and 2nd stage

gear assemblies for damage or excessive wear. Replace,

if necessary.

10. Remove and inspect the front gear box assembly for

damage or excessive wear. If damaged or worn, replace

the front gear box assembly.

11. Install the motor into the gearbox housing. Make sure the

housing gasket is positioned properly.

12. Secure the motor with the three motor mounting screws.

13. Reconnect the wires between the sprayer and the motor.

(refer to the electrical schematic in the Parts List section

of this manual).

14. Position the electronic cover over the electronic control

assembly. Secure the electronic cover with the three

electronic cover screws.

15. Slip the baffle assembly up and around the motor. Secure

the baffle assembly with the tie wrap.

16. Slide the motor shroud over the motor. Make sure the

shroud gasket is positioned properly.

17. Secure the motor shroud with the four motor shroud

screws.

Front End Bell

Assembly

Armature Gear

1st Stage Gear

2nd Stage Gear

Front Gear Box

Assembly

Housing

Gasket

Shroud

Gasket

NOTE: Clean and refill the gear box cavity up to the rear

face of each gear with Lubriplate (P/N 314-171).

Replacing the Transducer

1. Unplug the unit.

2. Loosen and remove the four motor shroud screws.

Remove the motor shroud.

3. At the electronic control assembly, disconnect the wire

coming from the transducer.

4. Pull the grommet out of the mounting plate and slide it up

the shaft of the transducer until it is clear of the mounting

plate.

5. Using a wrench, loosen and remove the transducer from

the filter housing. Carefully thread the transducer wire out

through the mounting plate.

6. Slide the grommet off of the old transducer and onto the

new transducer.

7. Thread the new transducer wire through the mounting

plate and up to the electronic control assembly.

8. Thread the new transducer into the filter housing and

tighten securely with a wrench.

9. Push the grommet into the mounting plate.

10. Connect the transducer wire to the electronic control

assembly (refer to the electrical schematic in the Parts List

section of this manual).

11. Slide the motor shroud over the motor. Make sure the

shroud gasket is positioned properly.

12. Secure the motor shroud with the four motor shroud

screws.

Motor Shroud

Transducer

Grommet

Motor Shroud Screws

Electronic Control

Assembly

Mounting Plate

To Filter

NOTE: Make sure the o-ring on the transducer is in

place before threading the transducer into the

filter housing.

Replacing the PRIME/SPRAY Valve

Perform the following procedure using PRIME/SPRAY valve

replacement kit P/N 800-915.

1. Push the groove pin out of the valve handle.

2. Remove the valve handle and the cam base.

3. Using a wrench, loosen and remove the valve housing

assembly.

4. Make sure the gasket is in place and thread the new valve

housing assembly into the filter block. Tighten securely

with a wrench.

5. Place the cam base over the valve housing assembly.

Lubricate the cam base with grease and line up the cam

with the filter block using the dowel pin.

6. Line up the hole on the valve stem with the hole in the

valve handle.

7. Insert the groove pin into the valve handle and through

the valve stem to secure the valve handle in position.

Servicing the Fluid Section

Use the following procedures to service the valves and repack

the fluid section. Perform the following steps before

performing any maintenance on the fluid section.

1. Loosen and remove the four front cover screws. Remove

the front cover.

2. Position the crankshaft/slider assembly at the bottom,

dead-center of its stroke so that the connecting pin and

retaining ring are visible below the slider assembly. This

is done by turning the sprayer on and off in short bursts

until the connecting pin is visible below the slider housing.

3. Turn off and unplug the unit.

Before proceeding, follow the Pressure Relief

Procedure outlined previously in this manual.

Additionally, follow all other warnings to reduce

the risk of an injection injury

, injury from moving

parts or electric shock. Always unplug the

sprayer before servicing!

4. Remove the return hose from the clamp on the siphon

tube.

5. Unscrew the siphon tube/siphon set from the foot valve.

Loosen and remove the high-pressure hose from the

nipple on the back of the upper housing of the fluid

section.

Gasket

Dowel Pin

Cam Base

Valve Stem

Filter

Housing

Valve Housing

Assembly

Valve

Handle

Groove Pin

Servicing the Valves

The design of the fluid section

allows access to the foot valve and

seat as well as the outlet valve and

seat without completely

disassembling the fluid section. It

is possible that the valves may not

seat properly because of debris

stuck in the foot valve seat or outlet

valve seat. Use the following

instructions to clean the valves and

reverse or replace the seats.

1. Loosen and remove the foot

valve housing from the lower

housing.

2. Clean out any debris in the foot

valve housing and examine the

housing and the foot valve

seat. If the seat is damaged,

reverse or replace the seat.

3. Using two wrenches, hold the

upper housing at the wrench

flats with one wrench and loosen the lower housing with

the other. Remove the lower housing.

4. Using a 3/4” wrench, loosen and

remove the outlet valve retainer

from the piston rod.

5. Clean out any debris and

examine the retainer and outlet

valve seat. If the seat is

damaged, reverse or replace the

seat.

6. Remove, clean, and inspect the

outlet valve cage and outlet

valve ball. Replace if they are

worn or damaged.

7. Reassemble the valves by reversing the steps above.

NOTE: During reassembly, make sure the Viton o-rings

and the PTFE back-up rings between the upper

housing and lower housing as well as between

the lower housing and the foot valve housing

are lubricated with grease and in position.

NOTE: Always service the

outlet valve with the

piston rod attached to

the pump. This will

prevent the piston rod

from rotating during

disassembly of the

outlet valve.

Outlet Valve

Retainer

Nylon

Washer

Outlet Valve

Seat

Outlet Valve

Ball

Outlet Valve

Cage

Outlet Valve

Seal

Piston Rod

Upper

Housing

Lower

Housing

Foot Valve

Housing

Viton

O-Ring

O-ring

PTFE

Back-Up

Ring

Foot Valve

Seat

Foot Valve

Ball

Foot Valve

Cage

Lower

Housing

Upper

Housing

Repacking the Fluid Section

1. Remove the foot valve

assembly and the lower

housing using the steps in the

“Servicing the Valves”

procedure above.

2. Slide the retaining ring up on

the slider assembly to expose

the connecting pin.

3. Push the connecting pin

forward through the slider

assembly and piston. The

connecting pin will fall into a

recessed area of the gear box

housing where it can be

retrieved.

4. Tap the knock-off nut with a

soft hammer so that it turns

counterclockwise and loosens.

5. Turn the fluid section

counterclockwise to remove it

from the gear box housing.

6. Place the upper housing

upright in a vise by clamping

on the wrench flats.

7. Using a wrench, remove the

upper seal retainer.

8. Slide the piston rod out through

the bottom of the upper

housing.

9. Inspect the piston rod for wear

and replace if necessary.

10. Remove the upper and lower packings from the upper

housing.

11. Clean the upper housing. Inspect the upper housing for

damage and replace if necessary.

12. Locate the new upper and lower packings and pack the

areas between the packing lips with grease. Lubricate the

o-rings on the exterior of the packings with grease.

13. Insert the upper packing into the

top of the upper housing with

the raised lip on the packing

facing down.

14. Insert the spacer on top of the

upper packing.

15. Thread the upper seal retainer

into the upper housing and

torque to 25-30 ft. lbs.

Install upper packing

with raised lip

facing down.

Raised Lip

NOTE: Be careful not to scratch, score, or otherwise

damage the upper housing during removal of

the packings.

NOTE: Do not over-tighten

the vise. Damage to

the upper housing

may occur.

NOTE: The outlet valve does

not need to be

disassembled from

the piston rod for this

procedure.

Retaining

Ring

Connecting

Slider

Assembly

Crankshaft

Knock-Off

Nut

Upper Seal

Retainer

Spacer

Upper

Packing

Lower

Packing

Upper

Housing

Piston Rod

Wear Ring

NOTE: The factory-installed packings are black in

color. The replacement packings in the

packing replacement kit are white.

16. Pre-form the lower packing using

the lower packing sizing tool

(included in the repacking kit).

17.

Insert the lower packing partially

nto the bottom of the upper

housing so that the side that

has the o-ring closest to the

face of the packing faces up.

18. Push the lower packing into

position using the lower packing

insertion tool (see Fluid Section

Assembly parts list for lower packing insertion tool P/N).

19. Place the piston insertion tool (included in the repacking

kit) over the top of the piston rod.

20. Insert the piston rod into the bottom of the upper housing,

through the lower packing, through the upper packing, and

out through the upper seal retainer.

21. Remove the piston insertion tool from the top of the piston

rod.

22. Turn the knock-off nut counterclockwise until it is flush

against the upper housing.

23. Lubricate the threads on the upper housing with anti-seize

compound. Remove the upper housing from the vise.

24. Thread the upper housing into the gear box housing,

turning clockwise. When the connecting pin hole on the

piston rod lines up with the hole in the slider assembly,

insert the connecting pin.

25. Slide the retaining ring down over the connecting pin.

26. Continue to turn the upper housing clockwise until the

knock-off nut is flush against the gear box housing.

27. Once the nipple is positioned, turn the knock-off nut

clockwise until it contacts the gear box housing.

28. Tap the knock-off nut with a soft hammer to tighten it

against the gear box housing.

29. Making sure that the Viton o-ring and PTFE back-up ring

are lubricated and in place, thread the lower housing into

the upper housing. Using two wrenches, hold the upper

housing at the wrench flats with one wrench and tighten

the lower housing with the other.

30. Attach the high-pressure hose to the nipple on the back of

the housing and tighten with a wrench. Do not kink the hose.

31. Making sure that the Viton o-ring and PTFE back-up ring

are lubricated and in place, reassemble the foot valve

assembly and and thread it into the lower housing.

Tighten securely.

32. Thread the siphon tube/siphon set into the foot valve and

tighten securely. Make sure to wrap the threads on the down

tube/siphon tube adapter with PTFE tape before assembly.

33. Replace the return hose into the clamp on the siphon tube.

34. Place the front cover on the gearbox housing and secure

in position using the four front cover screws.

35. Turn on the sprayer by following the procedure in the

“Operation” section of this manual and check for leaks.

NOTE: Repacking kit P/N 800-273 is available. For

best results use all parts supplied in this kit.

NOTE: For low rider units, make sure the hose does

not touch the cart frame. If it does, reposition

the nipple by turning the upper housing until

the hose is clear of the frame and the nipple is

within 45º of the back of the unit.

NOTE: If the nipple on the upper housing does not

face the back of the unit, turn the upper

housing counterclockwise until the nipple

faces the back of the unit. Do not turn the

upper housing more than one full turn.

NOTE: When repacking the fluid section, make sure

the raised lip on the bottom of the lower

packing is fully outside the packing around the

piston rod after insertion of the piston rod.

Install lower packing with

the side that has the o-ring

closest to the face of the

packing facing up.

Closer

Top

Solution

1. Plug the unit in.

2. Reset the breaker.

3. Turn the pressure control knob clockwise to

supply power to the unit and increase the

pressure setting.

4. Inspect or take to a Titan authorized service

center.

5. Allow motor to cool.

6. Replace the ON/OFF switch.

1. Rotate the PRIME/SPRAY valve clockwise

to the PRIME position.

2. Check the siphon tube/siphon assembly

connection and tighten or re-tape the

connection with PTFE tape.

3. Remove the pump filter element and clean.

Remove the inlet screen and clean.

4. Remove the siphon tube/siphon assembly

and clean.

1. Replace the spray tip following the

instructions that came with the spray gun.

2. Replace the spray tip with a tip that has a

smaller orifice following the instructions that

came with the spray gun.

3. Turn the pressure control knob clockwise to

increase the pressure setting.

4. Remove the pump filter element and clean.

Remove the gun filter and clean. Remove

the inlet screen and clean.

5. Clean or replace the PRIME/SPRAY valve.

6. Check the siphon tube/siphon assembly

connection and tighten or re-tape the

connection with PTFE tape.

7. Check for external leaks at all connections.

Tighten connections, if necessary.

8. Clean the valves and service the fluid

section following the “Servicing the Fluid

Section” procedure in the Maintenance

section of this manual.

9. Reverse or replace the valve seats

following the “Servicing the Fluid Section”

procedure in the Maintenance section of

this manual.

10. Take unit to a Titan authorized service

center.

1. Repack the pump following the “Servicing

the Fluid Section” procedure in the

Maintenance section of this manual.

2. Replace the piston rod following the

“Servicing the Fluid Section” procedure in

the Maintenance section of this manual.

1. Replace hose with a minimum of 50’ of 1/4”

grounded textile braid airless paint spray

hose.

2. Replace the spray tip following the

instructions that came with the spray gun.

3. Rotate the pressure control knob

counterclockwise to decrease spray

pressure.

Cause

1. The unit is not plugged in.

2. Tripped breaker.

3. The pressure is set too low (pressure

control knob set at minimum setting

does not supply power to unit).

4. Faulty or loose wiring.

5. Excessive motor temperature.

6. ON/OFF switch is defective.

1. The PRIME/SPRAY valve is in the

SPRAY position.

2. Air leak in the siphon tube/siphon

assembly.

3. The pump filter and/or inlet screen is

clogged.

4. The siphon tube/siphon assembly is

clogged.

1. The spray tip is worn.

2. The spray tip is too large.

3. The pressure control knob is not set

properly.

4. The pump filter, gun filter, or inlet

screen is clogged.

5. Material flows from the return hose

when the PRIME/SPRAY valve is in the

SPRAY position.

6. Air leak in the siphon tube/siphon

assembly.

7. There is external fluid leak.

8. There is an internal fluid section leak

(packings are worn and/or dirty, valve

balls are worn).

9. Worn valve seats

10. Motor powers but fails to rotate

1. The upper packings are worn.

2. The piston rod is worn.

1. Wrong type of airless spray hose.

2. The spray tip worn or too large.

3. Excessive pressure.

Problem

The unit will not run.

The unit will not prime.

The unit will not build or

maintain pressure.

Fluid leakage at the upper end

of the fluid section.

Excessive surge at the spray

gun.

Troubleshooting

Problem

Poor spray pattern.

The unit lacks power.

Cause

1. The spray tip is too large for the

material being used.

2. Incorrect pressure setting.

3. Insufficient fluid delivery.

4. The material being sprayed is too

viscous.

1. The pressure adjustment is too low.

2. Improper voltage supply.

Solution

1. Replace the spray tip with a new or smaller

spray tip following the instructions that

came with the spray gun.

2. Rotate the pressure control knob to adjust

the pressure for a proper spray pattern.

3. Clean all screens and filters.

4. Add solvent to the material according to the

manufacturer's recommendations.

1. Rotate the pressure control knob clockwise

to increase the pressure setting.

2. Reconnect the input voltage for 120V AC.

Xact Digital Control System Error Messages

The following error message screens appear whenever the

Xact Digital Control System detects a problem with the

sprayer. Once a problem occurs and the error message

appears, the sprayer will shut down.

Before proceeding, follow the Pressure Relief

Procedure outlined previously in this manual.

Additionally

, follow all other warnings to reduce

the risk of an injection injury, injury from moving

parts or electric shock. Always unplug the

sprayer before servicing!

Check Paint Screen (E1)

The Check Paint screen

appears when the pump

pressure drops to a very low

level and the pressure control knob has not been adjusted.

Check the paint level and refill. Restart the sprayer by

following the “Painting” procedure in the Operation section of

this manual.

Check Transducer Screen (E2)

The Check Transducer screen

appears when the transducer

has become disconnected or

is defective. T

ake the sprayer to a Titan authorized service

center for repair.

Check Motor Screen (E3)

The Check Motor screen

appears when the motor or

motor sensor is defective.

Take the sprayer to a

Titan authorized service center for repair.

Low Voltage Screen (E4)

The Low Voltage screen

appears when the sprayer

shuts down because of low

input voltage. Check the power supply and correct the

problem. Restart the sprayer by following the “Painting”

procedure in the Operation section of this manual.

High Motor Temperature Screen (E5)

The High Motor Temperature

screen appears when the

temperature of the motor has

risen too high.

Take the sprayer to a Titan authorized service

center for repair.

HIGH MOTOR

TEMPERATURE

LOW VOLTAGE

CHECK MOTOR

CHECK TRANSDUCER

CHECK PAINT

High Control Temperature Screen (E6)

The High Control Temperature

screen appears when the

temperature of the Xact Digital

Control System has risen too high.

Take the sprayer to a Titan

authorized service center for repair.

High Load Check Mechanism Screen (E7)

The High Load Check

Mechanism screen appears

when the sprayer shuts down

because of high current or when the sprayer goes into current

fold back mode..

Take the sprayer to a Titan authorized

service center for repair.

Exceeded Pressure Limit Screen (E8)

The Exceeded Pressure Limit

screen appears when the

sprayer pressure exceeds

3300 PSI / 22.8 MPa. Take the sprayer to a

Titan authorized

service center for repair.

Communication Error Screen (E9)

The Communication Error

screen appears when the Xact

Digital Control System loses

communication with the control panel.

Take the sprayer to a

Titan authorized service center for repair.

COMMUNICATION

ERROR

EXCEEDED

PRESSURE LIMIT

HIGH LOAD

CHECK MECHANISM

HIGH CONTROL

TEMPERATURE

Français

Importantes consignes de sécurité • Lire toutes ces consignes

avant d’utiliser l’appareil. Garder ces consignes.

Indique une situation à risque, laquelle, si elle n'est pas

évitée, peut entraîner des blessures graves, voire la

mort.

Pour réduire les risques d’incendie ou d’explosion, de

choc électrique et de blessure, vous devez lire et

comprendre les directives figurant dans ce manuel.

Familiarisez-vous avec les commandes et l’utilisation

adéquate de l’équipement.

DANGER : INJECTION CUTANÉE

Le jet de haute pression produit par cet appareil peut

transpercer la peau et les tissus sous-jacents, causant des

blessures graves pouvant entraîner l'amputation.

NE PAS TRAITER CE TYPE DE BLESSURE COMME UNE SIMPLE

COUPURE! Une amputation peut en résulter

. ON DOIT

CONSULTER UN MÉDICIN SUR-LE-CHAMP.

La pression maximale de ce pulvérisateur est d’environ 3 300 PSI /

22,8 MPa.

MESURES PRÉVENTIVES :

• Ne pas pointer le pistolet vers une partie du corps.

•

Ne pas pointer le pistolet vers une personne ou un animal; ne

pas pulvériser non plus de produit dessus.

• NE JAMAIS mettre une partie du corps devant le jet de produit.

NE JAMAIS toucher les fuites du flexible de pulvérisation.

• NE JAMAIS mettre la main, même gantée, devant le pistolet (les

gants n’offrent aucune protection contre les blessures par

injection).

• TOUJOURS verrouiller la détente, arrêter la pompe et relâcher toute

la pression avant d’effectuer la maintenance de l’appareil ou de le

laisser sans surveillance, d’en nettoyer le protège-embout ou

l’embout, ou de remplacer ce dernier. La pression ne sera pas

relâchée par le simple arrêt du moteur; pour ce faire, on doit se servir

du bouton PRIME/SPRAY (se reporter à la section COMMENT

LIBÉRER LA PRESSION, du présent manuel).

• TOUJOURS s'assurer que le protège-embout est en place avant de

pulvériser. Il est cependant à noter que, s’il assure une certaine

protection, ce dispositif joue surtout un rôle préventif.

• TOUJOURS retirer l’embout avant de vidanger ou de nettoyer

l’appareil.

• TOUJOURS inspecter le flexible avant de commencer; celui-ci

peut présenter des fuites attribuables à l’usure, à une flexion

excessibe ou à un traitement abusif, lesquelles fuites présentent

des risques d’injection cutanée. Ne pas utiliser le flexible pour

soulever ou tirer l’équipement.

• NE JAMAIS utiliser de pistolet sans verrou de détente et protège-

doigts.

• Tous les accessoires (pistolets, embouts, rallonges, flexibles etc.)

doivent pouvoir subir une pression nominale de 3 300 PSI / 22,8

MPa ou plus.

• Ne laissez pas l’appareil sous tension ou sous pression quand vous

vous en éloignez. Quand vous n’utilisez pas l’appareil, éteignez-le

et libérez la pression conformément aux instructions COMMENT

LIBÉRER LA PRESSION, du présent manuel.

• Vérifiez que toutes les connexions sont bien serrées avant

d’utiliser l’appareil. Toute pièce qui n’est pas fixée solidement

risque d’être projetée violemment ou d’entraîner la fuite d’un jet

de liquide à une pression extrêmement élevée, ce qui pourrait

causer des blessures graves.

• Verrouillez toujours la détente quand vous ne pulvérisez pas.

Vérifiez que le verrou de la détente fonctionne correctement.

REMARQUE À L’INTENTION DES MÉDECINS :

Les injections cutanées sont des lésions traumatiques; il

importe donc de les traiter sans délai. On NE DOIT PAS retarder

ce traitement sous prétexte de vérifier la toxicité du produit en

cause, celle-ci n’étant conséquente que dans le cas d’injection

directe de certains produits dans le système sanguin. Il pourrait

s’avérer nécessaire de consulter un plasticien ou un spécialiste

en chirurgie reconstructive de la main.

DANGER : ÉMANATIONS DANGEREUSES

Certains produits (peintures, solvants, insecticides ou autres)

peuvent être nocifs s’ils sont inhalés ou entrent en contact

avec l’organisme. Les émanations de ces produits peuvent

provoquer de graves nausées, évanouissements ou

empoisonnements.

MESURES PRÉVENTIVES :

• Se servir d’un masque ou d’un respirateur s’il y a

risque d’inhalation (lire toutes les directives concernant

ces dispositifs afin de s’assurer qu’ils offrent la

protection requise).

• Porter des lunettes de protection.

• Porter les vêtements de protection prescrits par le fabricant du

produit utilisé.

DANGER : EXPLOSION OU INCENDIE

Les émanations de certains produits peuvent exploser ou

s’enflammer, et risquent d’entraîner des dommages matériels

ou de graves blessures.

MESURES PRÉVENTIVES :

• S’assurer que l’aire de travail est dotée de moyens d’évacuation

d’air vicié et d’introduction d’air frais pour éviter l’accumulation de

vapeurs inflammables. Les vapeurs dégagées par la peinture ou

les solvants peuvent provoquer une explosion ou s’enflammer.

•

Ne pas pulvériser de produit dans un endroit clos.

• Ne pas travailler près de sources d’ignition (décharges

électrostatiques ou étincelles provoquées par le

branchement/ débranchement d’appareils ou la

commutation d’interrupteurs, d'appareils électriques, flammes

nues, veilleuses, objets chauds, etc.). La peinture ou le solvant

s’écoulant dans l’équipement peut générer de l’électricité statique.

• Ne pas fumer dans l’aire de travail.

• L’aire de travail doit être munie d’un extincteur en bon état de

marche.

• Prévoir un espace d’au moins 7.62 mètres entre la pompe et

l’objet à pulvériser s’ils sont dans la même pièce bien ventilée

(rallonger le flexible au besoin). Les vapeurs inflammables étant

souvent plus lourdes que l’air, l’espace au-dessus du plancher

doit être particulièrement bien aéré. La pompe contient des

pièces qui produisent des arcs et émettent des étincelles pouvant

enflammer les vapeurs.

• Les appareils et objets à l’intérieur ou à proximité de l’aire de

travail doivent être adéquatement mis à la terre pour éviter les

décharges électrostatiques.

• Veillez à ce que la zone soit propre et exempte de contenants de

peinture ou de solvant, chiffons ou autres matériaux

inflammables.

• Les flexibles dont on se sert doivent être conçus pour subir les

pressions élevées et faits de matériaux conducteurs ou mis à la

terre adéquatement; le pistolet sera mis à la terre par le biais de

ses raccords aux flexibles.

• Pour les appareils électriques — Le cordon d’alimentation doit

être branché à un circuit trifilaire.

• L’appareil doit toujours être vidangé à basse pression, embout

retiré, dans un contenant métallique distinct. Tenir le pistolet

contre la paroi du contenant de manière à mettre ce dernier à la

terre et à prévenir les décharges électrostatiques.

• Toujours respecter les mises en garde et les directives du

fabricant des produits et solvants utilisés. On doit connaître les

produits contenus dans les peintures et solvants qu'on pulvérise.

Lire les fiches techniques santé-sécurité (FTSS) et les étiquettes

des contenants fournies avec les peintures et solvants. Suivres

les consignes de sécurité du fabricant de peinture et de solvant.

• S’entourer de toutes les précautions possibles lorsqu’on utilise

des produits ayant un point d’éclair inférieur à 21°C (70°F). Le

point d'éclair est la température à laquelle le liquide peut créer

suffisamment de vapeurs et s'enflammer.

• Le plastique est générateur de décharges électrostatiques; ne

jamais en suspendre pour fermer une aire de travail ou en utiliser

en guise de toile de protection lorsqu’on pulvérise un produit

inflammable.

• Se servir de la pression la plus basse possible pour vidanger

l’appareil.

• Ne pas pulvériser de produit sur la pompe.

Français

Importantes consignes de sécurité • Lire toutes ces consignes

avant d’utiliser l’appareil. Garder ces consignes.

DANGER : EXPLOSION CAUSÉE PAR DES PRODUITS

INCOMPATIBLES

Ce type d’explosion peut entraîner des dommages matériels

ou des blessures graves.

MESURES PRÉVENTIVES :

• Ne pas utiliser de produits contenant du chlore ou du javellisant.

• Ne pas utiliser de solvants à base de halons comme l’eau de

javel, les agents antimoisissure, le chlorure de méthylène et le

trichloroéthane-1-1-1, lesquels ne sont pas compatibles avec

l’aluminium.

• Communiquer avec le fournisseur du produit concerné pour en

connaître la compatibilité avec l’aluminium.

DANGER : GÉNÉRALITÉS

D’autres dangers peuvent entraîner des dommages matériels ou des

blessures graves.

• Lire toutes les directives et consignes de sécurité avant d’utiliser

l’appareil.

• Observer tous les codes locaux, provinciaux, d’état et nationaux

régissant la ventilation, la prévention des incendies et le

fonctionnement de l’appareil.

• Aux États-Unis, le gouvernement a adopté des normes de

sécurité en vertu de l’Occupational Safety and Health

Act (OSHA).

Le cas échéant, on doit les consulter, notamment les parties 1910

des normes générales et 1926 des normes de construction.

• N’utiliser que les pièces autorisées par le fabricant; les utilisateurs

qui choisiront d’utiliser des composants dont les caractéristiques

techniques et les exigences en matière de sécurité sont

inférieures devront en assumer tous les risques et responsabilités.

• Tous les raccords, les tuyaux et les bouchons de remplissage

doivent être fixés solidement en place avant d’utiliser la pompe

de pulvérisation. Toute pièce qui n’est pas fixée solidement

risque d’être projetée violemment ou d’entraîner la fuite d’un jet

de liquide à une pression extrêmement élevée, ce qui pourrait

causer des blessures graves.

• Avant chaque utilisation, examiner tous les flexibles afin de

confirmer l’absence de coupures, de fuites, d’abrasions ou de

renflements. Vérifier également l’intégrité des raccords. Remplacer

sans délai les pièces qui semblent présenter des défectuosités. Ne

jamais tenter de réparer un flexible; remplacer ceux qui font défaut

par des modèles haute pression, avec mise à la terre.

•. Ne faites pas de nouer avec le tuyau et ne le tordez pas trop. Le

tuyau à vide peut présenter des fuites suite à l’usure, les nouer

ou les mauvais traitements. Une fuite risque d’injecter du produit

dans la peau.

•. N’exposez pas le tuyau à des températures ou des pressions

supérieures à celles spécifiées par le fabricant.

• Ne pas pulvériser à l’extérieur par grands vents.

• Porter des vêtements aptes à protéger la peau et les cheveux du

produit utilisé.

• Ne pas utiliser le pistolet ou ne pas pulvériser de produits en

présence d’enfants à proximité. Éloigner les enfants de

l’équipement en tout temps.

• Ne pas s'étirer ni ne travailler sur un support instable. Toujours

garder les deux pieds au sol pour rester en équilibre.

• Se servir de la pression la plus basse possible pour vidanger

l’appareil.

• Rester vigilant et faire attention à ce que l'on fait.

• Ne pas se servir de l'équipement en cas de fatigue ou si vos

aptitudes sont affaiblies par la consommation de drogues ou de

boissons alcoolisées.

• Pour les appareils électriques — Débranchez toujours le cordon

électrique de la prise avant de travailler sur l’équipement.

• N’utilisez pas le tuyau pour tirer ou soulever l’équipement.

• Ne pas soulever par la poignée de chariot en chargeant ou en

déchargeant.

Instructions de mise à la terre

Cet appareil doit être mis à la terre. La mise à la terre réduit

les risques d'électrocution lors d'un court-circuit en permettant

au courant de s'écouler par le fil de mise à la terre. Cet

appareil est muni d'un cordon électrique avec fil de mise à la

terre ainsi que d'une fiche de terre. La fiche doit être branchée

sur une prise installée correctement et mise à la terre

conformément à la réglementation et aux codes en vigueur.

Le fait de ne pas brancher correctement la

fiche trifilaire de l’appareil peut entraîner

des risques de choc électrique.

Si on doit réparer ou remplacer le cordon ou la fiche, ne pas

raccorder le fil de terre à la borne des broches plates (lames)

de cette dernière. Ce fil, normalement vert (avec ou sans

rayures jaunes), doit être relié à la broche de terre.

Consulter un technicien ou un électricien qualifié à défaut de

comprendre l’ensemble des présentes directives ou en cas

d’incertitude quant à la mise à terre de l’appareil. Ne pas

modifier la fiche de l’appareil; si elle ne s’adapte pas dans la

prise voulue, faire remplacer cette dernière par un électricien

qualifié.

IMPORTANT : Utiliser uniquement une rallonge à trois fils

munie d'une fiche de terre dans une prise secteur mise à

la terre correspondant au type de fiche de l'appareil.

S'assurer que votre rallonge est en bon état. Lorsque

vous utilisez une rallonge, assurez-vous qu'elle soit d'un

calibre suffisant pour supporter l'intensité du courant

requise par l'appareil. Une rallonge trop mince entraîne

une chute de tension, une diminution de l'intensité et une

surchauffe. Une rallonge de calibre 12 est recommandée.

Si vous devez utiliser une rallonge à l’extérieur, celle-ci

doit comprendre la marque W

-A après la désignation

indiquant le type de cordon. Par exemple, la désignation

SJTW-A indique que le cordon est conçu pour être utilisé

à l’extérieur.

Prise de terre

Goupille de mise à la terre

Couvercle du boîtier de prise de terre

Español

Información de seguridad importante • Lea toda la información de

seguridad antes de operar el equipo. Guarde estas instrucciones.

Indica una situación peligrosa que, de no evitarse,

puede causar la muerte o lesiones graves.

Para reducir los riesgos de incendios, explosiones,

descargas eléctricas o lesiones a las personas, lea y

entienda todas las instrucciones incluidas en este man-

ual. Familiarícese con los controles y el uso adecuado

del equipo.

PELIGRO: LESIÓN POR INYECCIÓN

El flujo de pintura a alta presión que produce este equipo

puede perforar la piel y los tejidos subyacentes,

ocasionando lesiones graves y posible amputación.

CONSUL

TE A UN MÉDICO INMEDIATAMENTE.

¡NO TRATE LA LESIÓN POR INYECCIÓN COMO UNA

CORT

ADURA SIMPLE! La inyección puede ocasionar

amputación. Consulte a un médico inmediatamente.

La gama operativa máxima de la pistola es de 3300 PSI / 22.8 MPa

de presión del líquido.

PREVENCIÓN:

• NUNCA apunte la pistola a ninguna parte del cuerpo.

• No apunte con la pistola ni rocíe a cualquier persona o animal.

• NUNCA deje que ninguna parte del cuerpo toque el flujo de

líquido. NO deje que el cuerpo toque una fuga de la manguera de

líquido.

• NUNCA ponga la mano frente a la pistola. Los guantes no

protegen contra una lesión por inyección.

• SIEMPRE ponga el seguro del gatillo, apague la bomba y libere

toda la presión antes de dar servicio, limpiar la boquilla o

protección, cambiar la boquilla o dejar la pistola sin supervisión. No

se libera la presión al apagar el motor. Debe girarse la perilla

PRIME/ SPRAY (CEBAR/ROCIAR) a PRIME (CEBAR) para aliviar

la presión. Consulte el PROCEDIMIENTO PARA ALIVIAR LA

PRESIÓN descrito en este manual.

• SIEMPRE mantenga la protección de la boquilla en su sitio al

rociar. La protección de la boquilla sirve principalmente de

dispositivo de advertencia.

• SIEMPRE retire la boquilla rociadora antes de enjuagar o limpiar

el sistema.

• La manguera de pintura puede presentar fugas por desgaste,

dobleces y maltrato. La fuga puede inyectar material traspasando

la piel. Inspeccione la manguera antes de cada uso. No use

mangueras para levantar o tirar del equipo.

• NUNCA use una pistola rociadora sin contar con el seguro y la

protección del gatillo.

• Todos los accesorios deben tener capacidades nominales de

3300 PSI / 22.8 MPa como mínimo. Esto incluye las boquillas

rociadoras, pistolas, extensiones y manguera.

• No deje el aparato con corriente ni con presión cuando nadie esté

pendiente de ella. Cuando no utilice el aparato, apáguelo y libere

la presión siguiendo las instrucciones del PROCEDIMIENTO

PARA ALIVIAR LA PRESIÓN descrito en este manual.

• Antes de utilizar el aparato, verifique que todas las conexiones

son seguras. Las partes no aseguradas pueden ser expulsadas

con gran fuerza o filtrar fluido a alta presión y provocar lesiones

severas.

• Ponga siempre el seguro del gatillo cuando no esté pulverizando.

Verifique que el seguro del gatillo funciona correctamente.

NOTA PARA EL MÉDICO: La inyección a través de la piel es una

lesión traumática. Es importante tratar la lesión tan pronto sea

posible. NO retrase el tratamiento para investigar la toxicidad. La

toxicidad es un factor a considerar con ciertos revestimientos

inyectados directamente en la corriente sanguínea. Puede ser

aconsejable consultar con un cirujano plástico o un cirujano

especialista en reconstrucción de las manos.

PELIGRO: VAPORES PELIGROSOS

Las pinturas, solventes, insecticidas y demás materiales

pueden ser nocivos si se inhalan o toman contacto con el

cuerpo. Los vapores pueden causar náuseas graves,

desmayos o envenamiento.

PREVENCIÓN:

• Use un respirador o mascarilla si pueden inhalarse los

vapores. Lea todas las instrucciones suministradas

con la mascarilla para revisar que brinde la protección

necesaria.

• Use lentes protectores.

• Use ropa protectora según lo indique el fabricante del

revestimiento.

PELIGRO: EXPLOSIÓN O INCENDIO

Los vapores de solventes y pinturas pueden explotar o

inflamarse. Pueden producirse daños materiales, lesiones

graves o ambos.

PREVENCIÓN:

• Cuente con escape y entrada de aire fresco para mantener el

aire dentro de la zona de aplicación sin acumulaciones de

vapores inflamables. Los gases producidos por solventes o

pinturas pueden causar explosiones o incendios.

•

No rocíe en lugares cerrados.

• Evite todas las fuentes de ignición como las chispas de

electricidad estática, las llamas expuestas, appliances

electricidad, las luces piloto y los objetos calientes. La conexión o

desconexión de cables eléctricos o interruptores de luz

operativos puede producir chispas. Si la pintura o el solvente

fluyen por el equipo se puede generar electricidad estática.

• No fume en el área de aplicación.

• Debe haber un extintor de incendios en buen estado.

• Coloque la bomba de pintura a un mínimo de 7.62 meters (25

pies) del objeto a pintar dentro de un área bien ventilada (añada

más manguera si es necesario). Los vapores inflamables son

generalmente más pesados que el aire. El área debe estar

sumamente bien ventilada.

• El equipo y los objetos dentro y alrededor del área a pintar deben

estar debidamente conectados a tierra para evitar las chispas de

estática.

• Mantenga el área limpia y libre de contenedores de pintura o

solvente, trapos y otros materiales inflamables.

• Use solamente una manguera conductora o conectada a tierra

para líquidos a alta presión. La pistola debe conectarse a tierra a

través de las conexiones de la manguera.

• Para las aparatos eléctricas — Debe conectarse el cable

eléctrico a un circuito a tierra.

• Siempre enjuague la unidad dentro de un recipiente metálico

separado, con la bomba a baja presión y habiendo sacado la

boquilla rociadora. Sostenga la pistola firmemente contra el

costado del recipiente para conectar a tierra el mismo y evitar

chispas de estática.

• Siga las advertencias e instrucciones del fabricante del material y

del solvente. Conozca los contenidos de las pinturas y los

solventes con los que rocía. Lea todas las Hojas de Datos sobre

Seguridad de Materiales (MSDS) y las etiquetas del contenedor

provistas con las pinturas y los solventes. Siga las instrucciones

de seguridad del fabricante de pinturas o solventes.

• Tenga muchísmo cuidado al usar materiales cuyo punto de

ignición sea inferior a 70°F (21°C). El punto de inflamación es la

temperatura a la que un fluido puede producir vapores suficientes

para encenderse.

• El plástico puede causar chispas de estática. Nunca cuelgue

plásticos para cerrar una zona a pintar. No use mantas plásticas

al aplicar materiales inflamables.

• Use la presión más baja posible para enjuagar el equipo.

• No rocíe el ensamblaje de la bomba.

Español

Información de seguridad importante • Lea toda la información de

seguridad antes de operar el equipo. Guarde estas instrucciones.

PELIGRO: POSIBLE EXPLOSIÓN DEBIDO A

MATERIALES INCOMPATIBLES

Causará daños materiales o lesiones graves.

PREVENCIÓN:

• No use materiales que contengan blanqueador o cloro.

• No use solventes de hidrocarburos halogenados como

blanqueador, mohocida, cloruro de metileno y 1,1,1 tricloroetano.

No son compatibles con el aluminio.

• Diríjase al proveedor de revestimientos para obtener los datos de

compatibilidad del material con el aluminio.

PELIGRO: GENERAL

Puede causar daños materiales o lesiones graves.

PREVENCIÓN:

• Lea todas las instrucciones y las precauciones de seguridad

antes de operar el equipo.

• Siga todos los códigos locales, estatales y nacionales

correspondientes que rijan la ventilación, prevención de

incendios y operación.

• Se han adoptado las normas de seguridad del Gobierno de los

Estados Unidos según la Ley de seguridad ocupacional y salud

(Occupational Safety and Health Act, OSHA). Deben consultarse

estas normas, particularmente el apartado 1910 de las Normas

generales y el apartado 1926 de las Normas de construcción.

• Utilice solamente componentes autorizados por el fabricante. El

usuario asume todo riesgo y responsabilidad al utilizar

componentes que no cumplan con las especificaciones mínimas

y requisitos de seguridad del fabricante de la bomba.

• Todos los acopladores, las mangueras y las tapas de los filtros

deben estar asegurados antes de operar la bomba de rocío. Las

partes no aseguradas pueden ser expulsadas con gran fuerza o

filtrar fluido a alta presión y provocar lesiones severas.

• Antes de cada uso, revise todas las mangueras en busca de

cortes, fugas, abrasión o hinchazón de la cubierta. Revise si hay

daños o movimiento de los acoplamiento. Cambie

inmediatamente la manguera si existe alguna de estas

condiciones. Nunca repare una manguera de pintura. Cámbiela

por otra manguera conectada a tierra apta para alta presión.

• No retuerza ni doble la manguera en exceso. En la manguera

airless pueden aparecer fugas a causa del desgaste, de

retorcimientos o de un mal uso. Una fuga puede inyectar material

en la piel.

• No exponga la manguera a temperaturas o presiones que

superen las especificadas por el fabricante.

• No pinte en exteriores en días con viento.

• Use ropa que mantenga la pintura alejada de la piel y el cabello.

• No lo opere ni rocíe cerca de los niños. Mantenga a los niños

alejados del equipo en todo momento.

• No se asome ni se pare sobre soportes inestables. Mantenga

siempre la posición firme y el equilibrio efectivos.

• Use la presión más baja posible para enjuagar el equipo.

• Manténgase alerta y mire lo que hace.

• No utilice la unidad cuando se encuentre cansado o bajo la

influencia de las drogas o el alcohol.

• Para las aparatos eléctricas — Desenchufe siempre el cable

antes de trabajar en el equipo.

• No utilice la manguera como elemento de fuerza para tirar del

equipo o levantarlo.

• No levantar por la manija del carro al cargar o descargando.

Instrucciones para conectar a tierra

Este producto se debe conectar a tierra. En caso de que

ocurra un corto circuito, la conexión a tierra reduce el riesgo

de choque eléctrico al proporcionar un alambre de escape

para la corriente eléctrica. Este producto está equipado con

un cable que tiene un alambre de conexión a tierra con un

enchufe de conexión a tierra apropiado. El enchufe se debe

enchufar en una toma de corriente que se haya instalado y

conectado a tierra debidamente, de acuerdo con todos los

códigos y estatutos locales.

La instalación incorrecta del enchufe a

tierra puede ocasionar un riesgo de

choque eléctrico.

Si es necesario reparar o cambiar el cable o el enchufe, no

conecte el cable verde a tierra a ninguno de las terminales de

espiga plana. El cable con aislamiento de color verde por

fuera con o sin rayas amarillas es el alambre a tierra y debe

conectarse a la espiga a tierra.

Consulte a un electricista o técnico de servicio capacitado si

las instrucciones para la conexión a tierra no se entienden

claramente o si tiene dudas en cuanto a que el producto esté

debidamente conectado a tierra. No modifique el enchufe que

se incluye. Si el enchufe no encaja en el receptáculo, pida a

un electricistas capacitado que instale un receptáculo

adecuado.

IMPORTANTE: Use solamente extensiones trifilares que

tengan un enchufe de conexión a tierra de 3 hojas y un

receptáculo de triple ranura que acepte el enchufe del

producto.

Asegúrese de que su extensión esté en buenas

condiciones. Cuando use una extensión, asegúrese de

usar una que sea lo suficientemente resistente como para

soportar la corriente que descargue su producto. Un cable

de un tamaño menor causará una caída de voltage en la

línea que dará como resultado una pérdida de energía y un

sobrecalenta|ôento. Se recomienda usar un cable de

calibre 12. Si se utiliza un cable de extensión en el exterior,

tiene que estar marcado con el sufijo W-A después de la

designación del tipo de cable. Por ejemplo, SJTW-A para

indicar que el cable es apropiado para uso en exteriores.

Tomacorriente aterrado

Terminal de tierra

Tapa de la caja del tomacorriente aterrado

Parts List

Main Assembly

Item Part # Description Quantity

1 800-600 Cart assembly.............................................1

2 800-036 Grommet.....................................................2

3 ---------- Drive assembly (see separate listing) ........1

4 761-178 Screw..........................................................4

5 800-324 Pail hook.....................................................1

6 763-551 Lock washer................................................2

7 858-625 Screw..........................................................2

8 800-328 Knock-off nut...............................................1

9 800-300 Fluid section assembly ...............................1

10 451-241 Siphon tube.................................................1

11 730-334 Hose clamp.................................................1

12 710-046 Inlet screen .................................................1

Item

Part # Description Quantity

14 800-904 Return hose ................................................1

15 800-900 Filter assembly............................................1

16 812-003 Outlet fitting.................................................1

17 800-915 PRIME/SPRAY valve assembly..................1

18 800-269 Fitting ..........................................................1

19 800-267 Fitting..........................................................1

20 860-002 Lock washer................................................2

21 860-535 Screw..........................................................2

22 800-266 Hose (not shown) .......................................1

800-590 Low rider cart

(not shown, see separate listing)

---------- Low rider siphon assembly

(not shown, see separate listing)

Item Part # Description Quantity

1 800-078 Electronic cover ..........................................1

2 800-205 Screw..........................................................3

3 800-984 Motor assembly ..........................................1

4 800-525 Housing gasket...........................................1

5 800-541 Shroud gasket.............................................1

6 800-261 1st stage gear assembly.............................1

7 800-262 2nd stage gear asembly .............................1

8 800-260 Front gearbox assembly)............................1

9 704-380 ON/OFF switch ...........................................1

10 800-510 Slider assembly ..........................................1

11 800-253 Slider housing.............................................1

12 700-283 Screw..........................................................4

13 800-406 Front cover..................................................1

14 800-284 Screw..........................................................4

15 800-382 Retaining ring..............................................1

16 800-753 Connecting pin............................................1

17 800-229 Ground screw .............................................1

18 779-568 Mounting plate ............................................1

19 800-077 Grommet.....................................................1

20 800-076 Screw..........................................................1

21 800-688 Control panel ..............................................1

22 704-486 Screw..........................................................4

23 704-488 Pressure control knob.................................1

24 704-469 Xact Digital Control System assembly

(optional).....................................................1

Item

Part # Description Quantity

25 704-467 Xact Digital Control system cover (optional) .1

26 704-487 Screw..........................................................2

27 779-567 Strain relief..................................................1

28 704-553 Power cord..................................................1

29 700-287 Screw..........................................................3

30 763-551 Lock washer................................................3

31 800-658 Electronic control assembly........................1

32 800-215 Fan shroud..................................................1

33 800-294 Fan assembly .............................................1

34 800-435 Baffle assembly ..........................................1

35 800-283 Screw..........................................................4

36 800-405 Motor shroud...............................................1

37 704-599 Dust cover (for sprayers without Xact

Digital Control System)...............................1

38 704-473 Control panel cover (for sprayers without

Xact Digital Control System).......................1

39 704-594 Surge suppressor (not shown) ...................1

40 800-929 Fuse, 15A (not shown)................................1

41 770-781 Electronic control mounting screw

(not shown).................................................4

42 765-060 Electronic control lock washer (not shown)..4

43 770-596 Electronic control washer (not shown) .......4

NOTE: All electrical work should be performed by a

Titan authorized service center.

Drive Assembly

Fluid Section Assembly (P/N 800-300)

Install lower packing with

the side that has the o-ring

closest to the top of the

packing facing up.

Install upper packing

with raised lip

facing down.

Raised Lip

Closer

Top

NOTE: When repacking the fluid section, make

sure the raised lip on the bottom of the

lower packing is fully outside the packing

around the piston rod after insertion of

the piston rod.

Item Part # Description Quantity

1 800-325 Upper seal retainer .....................................1

2 800-327 Spacer ........................................................1

3 800-248 Upper packing assembly ............................1

4 800-351 Upper housing ............................................1

5 800-250 Lower packing assembly ............................1

6 800-354 Wear ring ....................................................1

7 800-332 O-ring, Viton................................................2

8 800-333 Back-up ring, PTFE ....................................2

9 800-352 Lower housing ............................................1

10 800-246 Piston rod....................................................1

11 800-348 Outlet valve seal .........................................1

12 800-244 Outlet valve cage........................................1

13 800-247 Outlet valve ball ..........................................1

Item Part # Description Quantity

14 800-245 Washer, nylon .............................................1

15 800-243 Outlet valve seat.........................................1

16 800-336 Outlet valve retainer ...................................1

17 800-322 Foot valve cage ..........................................1

18 800-242 Foot valve ball ............................................1

19 800-241 Foot valve seat ...........................................1

20 762-058 O-ring..........................................................1

21 800-305 Foot valve housing .....................................1

22 800-365 Piston assembly (includes items 10–16) ....1

800-273 Repacking kit (includes items 2, 3, 5–8, 11,

13, 14, 18, and 20)

800-359 Lower packing insertion tool

High Rider Cart (P/N 800-600)

Item Part # Description Quantity

1 800-280 Handle

(includes items 2–5, 10, and 11) ................1

2 590-508 Roll pin........................................................2

3 590-507 Snap button ................................................2

4 590-504 Sleeve.........................................................2

5 590-506 Washer........................................................2

6 800-011 Spacer ........................................................2

7 710-199 Plug.............................................................2

8 800-279 Cart (includes items 7 and 9) .....................1

9 335-018 Plug.............................................................2

10 856-002 Washer........................................................4

11 856-921 Screw..........................................................4

12 800-007 Axle.............................................................1

13 670-109 Wheel..........................................................2

14 870-004 Washer........................................................2

15 800-019 Cap .............................................................2

Filter Assembly (P/N 800-900)

Item Part # Description Quantity

1 800-905 Filter body...................................................1

2 800-252 Filter spring.................................................1

3 730-067 Filter, 60 mesh ............................................1

4 702-251 Filter spring adapter....................................1

5 757-105 Core spring .................................................1

6 800-906 O-ring, PTFE ..............................................1

7 800-908 Plug, 3/8” ....................................................1

8 800-901 Filter housing ..............................................1

9 800-915 PRIME/SPRAY valve assembly..................1

10 800-907 Plug, 1/4” ....................................................1

11 800-437 Transducer..................................................1

Low Rider Cart (P/N 800-590)

Item Part # Description Quantity

1 590-506 Washer........................................................2

2 590-504 Sleeve.........................................................2

3 590-507 Snap button ................................................2

4 800-113 Handle assembly

(includes items 1–3 and 5–7) .....................1

5 590-508 Roll pin........................................................2

6 856-921 Screw..........................................................4

7 856-002 Washer........................................................4

8 700-674 Plug.............................................................2

Item

Part # Description Quantity

9 704-188 Screw..........................................................1

10 335-018 Plug.............................................................2

11 700-1041 Drip cup ......................................................1

12 704-291 Roll pin........................................................2

13 800-109 Wheel spacer..............................................2

14 800-593 Wheel..........................................................2

15 800-111 Cap .............................................................2

16 800-112 Cart weldment (includes items 8 and 10)...1

Low Rider Siphon Assembly

Item Part # Description Quantity

1 800-903 Return hose ................................................1

2 710-203 Siphon tube.................................................1

3 710-195 Swivel .........................................................1

4 710-046 Inlet screen .................................................1

5 730-334 Clamp .........................................................1

6 710-081 Siphon tube adapter ...................................1

7 700-742 Tie wrap (not shown) ..................................3

710-204 Siphon tube assembly

(includes items 2–6) ...................................1

Labels

Part # Description

313-1708 1140ix logo label

313-2641 “Titan” front label

313-1673 Warning label (injection/explosion)

313-1847 Shock hazard label

313-2395 Infinity logo label

313-2324 X-Lock label

313-2327 Xact Digital Control System label

313-2328 Xact Instruction label

313-2430 Transducer warning label

Transducer

Electronic Control

Assembly

Potentiometer

Motor

Plug

Control Panel

Board

Surge

Suppressor

Fuse

Switch

Ground

WHITE

BLACK

WHITE

AC-Motor

AC-NeutAC-Line

AC-Motor

J16 J9

J2 J1

J12 J7

WHITE

BLACK

GREEN

Electrical Schematic

NOTE: All electrical work should be performed

by a Titan authorized service center.

PRIME/SPRAY Valve Assembly

(P/N 800-915)

Item Part # Description Quantity

1 800-915 PRIME/SPRAY valve assembly..................1

2 700-537 Gasket ........................................................1

3 222-012 O-ring, PTFE ..............................................1

4 221-012 O-ring, Viton................................................1

5 700-721 Valve stem o-ring, Viton..............................1

700-897 Valve stem o-ring, PTFE (optional)

6 700-252 Cam base ...................................................1

7 700-759 Groove pin ..................................................1

8 700-697 Valve handle ...............................................1

NOTE: When using “hot” solvents, replace Viton

valve stem o-ring (item 5) with optional PTFE

valve stem o-ring (P/N 700-897). Install using

o-ring replacement tool (P/N 700-890).

Accessories

Airless Tip Selection

Tips are selected by the orifice size and fan width. The proper

selection is determined by the fan width required for a specific

job and by the orifice size that will supply the desired amount

of fluid and accomplish proper atomization.

For light viscosity fluids, smaller orifice tips generally are

desired. For heavier viscosity materials, larger orifice tips are

preferred. Please refer to the chart below.

The following chart indicates the most common sizes and the

appropriate materials to be sprayed.

Fan widths measuring 8" to 12" (20 to 30 cm) are preferred

because they offer more control while spraying and are less

likely to plug.

Liquid Shield Plus

Cleans and protects spray systems

against rust, corrosion and premature

wear. Now with -25º anti-freeze

protection.

Part #

Description

314-483...........4 ounce bottle

314-482...........1 quart bottle

Piston Lube

Specially formulated to prevent materials

from adhering to the piston rod, which

becomes abrasive to the upper seals.

Piston Lube will break down any material

that may accumulate in the oil cup and

keep it from drying.

Part #

Description

314-481...........4 ounce bottle

314-480...........8 ounce bottle

LX-80

Airless Gun

• 3600 PSI

• All metal construction

• In-handle filter

• High pressure swivel

Part No.

Description

580-100...........LX-80

— 4 Finger Gun

581-085...........LX-80

— 2 Finger Gun

580-050...........LX-80

— 4 Finger GTH Kit

581-150...........LX-80

— 2 Finger GTH Kit

S-3 Stainless Steel Airless Gun

• 3900 PSI

• Stainless Steel fluid passages

• High Pressure Swivel

• In-handle filter

• 4-finger trigger pull

Part No.

Description

550-250...........S-3 — 4 Finger Gun

Tip Size Spray Material Filter Type

.011 – .013 Lacquers and stains 100 mesh filter

.015 – .019 Oil and latex 60 mesh filter

.021 – .026 Heavy bodied latex and blockfillers 30 mesh filter

NOTE: Do not exceed the sprayer's recommended

maximum tip size.

Synergy Fine Finish Tips

• Perfect for all fine finish work

• Ideal for lacquers, stain, enamels, urethane, and clear top

coats

• Increases standard tip life up to 80%

• Delivers up to a 27% finer atomization at lower pressures

• Increases transfer efficiency resulting in less overspray

Part No.

Description

671-XXX ..........Synergy Fine Finish Tips

WideSpray Reversible Tips

• Designed for high production applications

• Increase production up to 100%

• WideSpray will save time and make you more money

Part No.

Description

661-XXXX .........WideSpray Reversible Tips

I-Remote Universal Remote Control System

• Operates your sprayer from over 100 feet away

• Works through walls, trees and other obstacles

• Increase or decrease the pressure of the sprayer without

climbing down off the ladder

Part No.

Description

800-690...........I-Remote Control System

800-691...........I-Remote Control Only

800-692...........I-Remote Receiver Only

Xact Digital Control System

The Xact Digital Control System is an optional add-on that

increases the functionality of the sprayer. It consists of a

display and four function keys. The display shows the user

menu features that enable the user to become more

productive and profitable

• X-Lock Security Features (Individualized Codes)

• Pressure Reading — Set Pressure and Working Pressure

• User Preset Keys

• Total Gallons Sprayed

• Resetable Job Gallon Counter

• Total On Time and Run Time

• Resetable On Time and Run Time

• Programmable Service Time (Hour Meter)

• Advanced Diagnostics

Part No.

Description

704-555...........Xact Digital Control System with Cover

Miscellaneous

Part No. Description

490-012...........Hose Coupling, 1/4" x 1/4"

730-397...........High Pressure Fl. Gauge

314-171...........Lubriplate, 14 ounce individual

314-172...........Lubriplate, 6 lb. can

700-1037..........Electrostatic discharge (ESD) wrist strap

Notes/Nota

United States Sales & Service

1770 Fernbrook Lane

Minneapolis, MN 55447

www.titantool.com

200 Trowers Road, Unit 7B

Woodbridge, Ontario L4L 5Z8

Tech Service/Order Entry:

Fax (Order Entry):

Fax (Tech Service):

1-800-526-5362

1-800-528-4826

1-800-525-9501

Phone:

Fax:

1-800-565-8665

1-800-856-8496

Canadian Branch

1770 Fernbrook Lane

Minneapolis, MN 55447

Phone:

Fax:

1-201-337-1240

1-201-405-7449

International

Material Safety Data Sheets (MSDS) are available on Titan’s website or by calling Customer Service.

Titan Tool, Inc., (“Titan”) warrants that at the time of delivery to the original purchaser for use (“End User”), the equipment

covered by this warranty is free from defects in material and workmanship. With the exception of any special, limited, or

extended warranty published by Titan, Titan’s obligation under this warranty is limited to replacing or repairing without charge

those parts which, to Titan’s reasonable satisfaction, are shown to be defective within twelve (12) months after sale to the End

User. This warranty applies only when the unit is installed and operated in accordance with the recommendations and

instructions of Titan.

This warranty does not apply in the case of damage or wear caused by abrasion, corrosion or misuse, negligence, accident,

faulty installation, substitution of non-Titan component parts, or tampering with the unit in a manner to impair normal operation.

Defective parts are to be returned to an authorized Titan sales/service outlet. All transportation charges, including return to the

factory, if necessary, are to be borne and prepaid by the End User. Repaired or replaced equipment will be returned to the End

User transportation prepaid.

THERE IS NO OTHER EXPRESS WARRANTY. TITAN HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES

INCLUDING, BUT NOT LIMITED TO, THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, TO

THE EXTENT PERMITTED BY LAW. THE DURATION OF ANY IMPLIED WARRANTIES WHICH CANNOT BE DISCLAIMED IS

LIMITED TO THE TIME PERIOD SPECIFIED IN THE EXPRESS WARRANTY. IN NO CASE SHALL TITAN LIABILITY EXCEED

THE AMOUNT OF THE PURCHASE PRICE. LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES

UNDER ANY AND ALL WARRANTIES IS EXCLUDED TO THE EXTENT PERMITTED BY LAW.

TITAN MAKES NO WARRANTY AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE WITH RESPECT TO ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT

MANUFACTURED BY TITAN. THOSE ITEMS SOLD, BUT NOT MANUFACTURED BY TITAN (SUCH AS GAS ENGINES,

SWITCHES, HOSES, ETC.) ARE SUBJECT TO THE WARRANTY, IF ANY, OF THEIR MANUFACTURER. TITAN WILL PROVIDE

THE PURCHASER WITH REASONABLE ASSISTANCE IN MAKING ANY CLAIM FOR BREACH OF THESE WARRANTIES.

Warranty

Patents

These products are covered by one or more of the following U.S. patents:

6,031,352 5,848,566 5,769,321 5,725,364 5,671,656 5,435,697 5,228,842

5,346,037 5,252,210 5,217,238 5,192,425 4,908,538 4,768,929 4,744,571

D384,676 6,179,222 5,934,883 4,723,892

Titan 1140IX El manual del propietario

Marca: Titan

Modelo: 1140IX

Categoría: Rociador de pintura

Tipo: El manual del propietario

Descargar PDF

informe

En otros idiomas

français: Titan 1140IX Le manuel du propriétaire
English: Titan 1140IX Owner's manual

Titan 1140IX El manual del propietario

Titan 1140IX El manual del propietario

En otros idiomas

Documentos relacionados

Otros documentos