Sharp FX-J80U El manual del propietario

Marca: Sharp

Modelo: FX-J80U

Categoría: Purificadores de aire

Tipo: El manual del propietario

ENGLISH

AIR PURIFIER

OPERATION MANUAL

PURIFICADOR DE AIRE

MANUAL DE OPERACIÓN

ESPAÑOL

“Plasmacluster” and “Device of a cluster of grapes” are

registered trademarks of Sharp Corporation in Japan,

USA and elsewhere.

FX-J80U

This product earned the ENERGY STAR label by

meeting strict energy e ciency guidelines set by the

U.S. EPA. Room air cleaners have demonstrated the

potential for improving air quality and providing health

bene ts. EPA does not endorse manufacturer claims

regarding the degree to which a speci c product will

produce healthier indoor air.

The energy e ciency of this ENERGY STAR certi ed

model is measured based on a ratio between the

model’s CADR for Smoke and the electrical energy it

consumes, or CADR/Watt.

Este producto obtuvo el sello de ENERGY STAR al

cumplir las estrictas pautas de e ciencia energética

establecidas por la EPA de EE. UU. Los puri cadores

del aire de la habitación han demostrado el potencial

para mejorar la calidad del aire y proporcionar

bene cios para la salud. La EPA no respalda las

a rmaciones del fabricante con respecto al grado en

que un producto especí co producirá aire interior más

saludable.

La e ciencia energética de este modelo con la

certi cación ENERGY STAR se mide en base a una

relación entre el CADR del modelo para el humo de

tabaco y la energía eléctrica que consume, o CADR/

vatio.

FX-J80U_3rd_EN.indd 1FX-J80U_3rd_EN.indd 1 2021/09/29 11:39:072021/09/29 11:39:07

ENGLISH

CONTENTS

FOR CUSTOMER ASSISTANCE ...................................... EN-2

CONSUMER LIMITED WARRANTY ................................ EN-3

IMPORTANT SAFETY INSTRUCTIONS .......................... EN-4

PART NAMES ................................................................... EN-7

FILTER INSTALLATION ................................................... EN-9

OPERATION ..................................................................... EN-10

CARE AND MAINTENANCE ............................................ EN-13

TROUBLESHOOTING ...................................................... EN-16

SPECIFICATIONS ............................................................. EN-17

OTHER SETTINGS ........................................................... EN-18

Intellectual property rights for this product .................. EN-22

Thank you for purchasing this SHARP Air Purifier.

Please read this manual carefully before using the product.

This manual should be kept in a safe place for future reference.

FX-J80U_3rd_EN.indd 2FX-J80U_3rd_EN.indd 2 2021/09/29 11:39:082021/09/29 11:39:08

ENGLISH

EN-1

The air purier draws in room air through

the air inlet, circulates it through a pre-lter,

an Active carbon deodorizing lter and a

true HEPA lter inside the main unit, and

then discharges it through the air outlet. The

True HEPA lter can remove 99.97% of dust

particles as small as 0.3 microns that pass

through the lter and also helps absorb

odors. The Active carbon deodorizing lter

gradually absorbs odors as they pass

through the lter.

Some odors absorbed by the lters will break down over time, causing additional odors.

Depending on usage conditions, and especially if the product is used in environments

signicantly more severe than a normal household, these odors may become noticeable sooner

than expected. If these odors persist, replace the lters. (Page 9,14)

• The air purifier is designed to remove air-suspended dust and the odors.

The air purifier is not designed to remove harmful gases such as carbon monoxide contained in cigarette smoke.

The air purifier may not completely remove an odor if the source of the odor is still present.

Please read before operating your new Air Purifier

NOTE

Declaration of Conformity

SHARP AIR PURIFIER FX-J80U

This device complies with Part 18 of FCC

rules.

Responsible Party:

SHARP ELECTRONICS CORPORATION

100 Paragon Drive, Montvale, NJ 07645,

U.S.A.

This Wi-Fi adapter complies with Part 15 of the

FCC rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any

interference received, including interference that

may cause undesired operation.

• Contains FCC: RX3-B01

True HEPA Filter

Active Carbon

Deodorizing Filter

Back Panel

(Pre-Filter)

FX-J80U_3rd_EN.indd 1FX-J80U_3rd_EN.indd 1 2021/09/29 11:39:092021/09/29 11:39:09

EN-2

FOR CUSTOMER ASSISTANCE

Registering your new product is easy and offers beneﬁ ts that help you get the most

out of your Sharp product including:

Convenience: If you ever need warranty support, your product information is already on ﬁ le.

Communication: Stay up to date with important notiﬁ cations and special offers from SHARP.

Support: Quickly access support content including Owners Manuals, FAQ’s,

How-to Videos, and much more.

3 EASY WAYS TO REGISTER TODAY!

PRODUCT SUPPORT

If you have questions about the setup or operation of your product, please refer to

the corresponding section within this manual.

Additionally, visit www.sharpusa.com/support to access exclusive content about your

product including:

FAQ’s and How-To Videos

Find or Request Service

Downloads including the Installation Guide, Spec Sheet, and Owner’s Manual

If at any time you have questions or comments concerning your SHARP product,

please contact the SHARP Customer Assistance Center. We are available to

assist you through multiple contact methods for your convenience:

Scan this QR Code on your smart phone Visit http://www.sharpusa.com/register

ONLINE

Visit our sites to

learn more about

your product at

sharpusa.com and

sbl.sharpusa.com

See the Contact Us section on our sites U.S. | www.sharpusa.com/support Contact a Sharp Advisor on the phone

Contact a Sharp Advisor on the phone

CALL US

US 800-BE-SHARP

800-237-4277

Mon-Fri: 7am-7pm CST

Sat-Sun: 9am-7pm CST

CALL US

US 800-BE-SHARP

800-237-4277

Mon-Fri: 7am-7pm CST

Sat-Sun: 9am-7pm CST

Available 24/7

US: sharpusa.com

CHAT ONLINE

Mon-Fri: 7am-7pm CST

Sat-Sun: 9am-7pm CST

SCAN

Use the camera or

QR code scanning

application on your

smart phone

customer_assistance_consumer_us(EN)_取説用_2021September_mono.indd 1customer_assistance_consumer_us(EN)_取説用_2021September_mono.indd 1 2021/09/01 13:13:172021/09/01 13:13:17

FX-J80U_3rd_EN.indd 2FX-J80U_3rd_EN.indd 2 2021/09/29 11:39:102021/09/29 11:39:10

EN-3

ENGLISH

CONSUMER LIMITED WARRANTY

CONSUMER LIMITED WARRANTY FOR U.S. USERS

SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand

product (the “Product”), when shipped in its original container, will be free from defective workmanship and

materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or

part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the

period(s) set forth below.

This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set

forth below nor to any Product the exterior of which has been damaged or defaced, which has been subjected

to improper voltage or other misuse, abnormal service or handling, or which has been altered or modified in

design or construction.

In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below

and provide proof of purchase to the servicer.

The limited warranty described herein is in addition to whatever implied warranties may be granted to

purchasers by law. ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR USE ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET

FORTH BELOW. Some states do not allow limitations on how long an implied warranty lasts, so the above

limitation may not apply to you.

Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than

those described herein, or to extend the duration of any warranties beyond the time period described herein

on behalf of Sharp.

The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be

the sole and exclusive remedy available to the purchaser. Correction of defects, in the manner and for the

period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of

Sharp to the purchaser with respect to the Product, and shall constitute full satisfaction of all claims, whether

based on contract, negligence, strict liability or otherwise. In no event shall Sharp be liable, or in any way

responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs

performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any way responsible

for any incidental or consequential economic or property damage. Some states do not allow the exclusion of

incidental or consequential damages, so the above exclusion may not apply to you.

THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF

COLUMBIA AND PUERTO RICO.

Your Product Model Number & Description:

Warranty Period for this Product:

Additional Item(s) Excluded From Warranty

Coverage:

Where to Obtain Service:

What to Do to Obtain Service:

FX-J80U Air Purier. Be sure to have this information

available when you need service for your Product.

One (1) year parts and labor from date of purchase.

Appearance items of the Product, lters, accessories, or

any printed materials. Product which has been used for

rental and/or commercial purposes.

From a Sharp Authorized Servicer located in the United

States. To nd the location of the nearest Sharp Authorized

Servicer, call Sharp Toll Free at 1-800-BE-SHARP.

Ship prepaid or carry in your Product to a Sharp Authorized

Servicer. Be sure to have Proof of Purchase available. If

you ship the Product, be sure it is insured and packaged

securely.

TO OBTAIN SERVICE, SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP,

OR VISIT OUR WEBSITE AT www.sharpusa.com

SAVE THE PROOF OF PURCHASE AS IT IS NEEDED SHOULD YOUR AIR PURIFIER EVER REQUIRE

WARRANTY SERVICE.

SHARP ELECTRONICS CORPORATION

100 Paragon Drive, Montvale, NJ 07645, U.S.A.

FX-J80U_3rd_EN.indd 3FX-J80U_3rd_EN.indd 3 2021/09/29 11:39:102021/09/29 11:39:10

EN-4

IMPORTANT SAFETY INSTRUCTIONS 1

Read and save these instructions

before using this product.

When using electrical appliances, basic

safety precautions should always be

followed to reduce the risk of fire, electric

shock, and injury to persons, including the

following:

WARNING

1. Read all instructions before using the

product.

2. Use the product only for intended

household use as described in

this manual. Any other use not

recommended by the manufacturer

may cause fire, electric shock, or injury

to persons.

3. This appliance is not intended for use

by persons (including children) with

reduced physical, sensory or mental

capabilities, or lack of experience

and knowledge, unless they have

been given supervision or instruction

concerning use of the appliance by a

person responsible for their safety.

Children should be supervised to

ensure they do not play with the

appliance.

4. Never operate the product if the power

cord or plug is damaged or the product

is malfunctioning or damaged.

5. If the power cord or plug is damaged, it

must be replaced by the manufacturer,

its service agent or a Sharp authorized

Service Center in order to avoid a

hazard.

Contact the nearest Service Center for

any problems, adjustments, or repairs.

6. Do not repair or disassemble the

product yourself.

7. Follow the instructions a to h below for

the power cord or plug. It may cause

short circuit, excessive heat, electric

shock or fire.

a. Use only AC 120 volt outlet.

b. Do not use the product if the power

code or plug is damaged or the

connection to the wall outlet is

loosened.

c. Always turn off the product before

unplugging the power plug.

d. Always unplug the product before

moving or maintaining it, opening the

back panel, changing the filters and

whenever the product is not in use.

e. Be sure to pull the power plug and

not the power cord.

f. Do not touch the power plug with wet

hands when inserting or unplugging

from the wall outlet.

g. Periodically remove dust from the

power plug.

h. Always observe the following not to

damage the power cord.

• Do not run cord under carpeting.

Do not cover the power cord with

throw rugs, runners, or similar

coverings.

• Do not put heavy things on the

power cord or pinch it.

• Do not run the power cord under

furniture or other appliances.

• Run the power cord away from

traffic area and where it will not be

tripped over.

8. The product has a polarized plug

(one blade is wider than the other). To

reduce the risk of electric shock, this

plug is intended to fit in a polarized

outlet only one way. If the plug does not

fit fully in the outlet, reverse the plug.

If it still does not fit, contact a qualified

electrician or service person. Do not

attempt to defeat this safety feature.

9. Do not use this product near gas

appliances, fire places, candle fire,

incense or sparks from lit cigarettes.

10. Do not operate the product in a room

with flammable gas, such as oily

residue or chemical fumes.

11. Do not expose the product to rain, or

use near water, in a bathroom, laundry

area or other damp location.

12. Do not insert fingers or foreign objects

into the air inlets or air outlets.

13. Do not look into the air outlets.

FX-J80U_3rd_EN.indd 4FX-J80U_3rd_EN.indd 4 2021/09/29 11:39:102021/09/29 11:39:10

EN-5

ENGLISH

NOTE - Radio or TV Interference

If the product should cause interference to

radio or television reception, try to correct

the interference by one or more of the

following measures:

1. Reorient or relocate the receiving

antenna.

2. Increase the separation between the

product and radio/TV receiver.

3. Connect the product into an outlet on

a circuit different from that to which the

receiver is connected.

4. Consult the dealer or an experienced

radio/TV technician for help.

CAUTIONS CONCERNING

INSTALLATION

1. Place the product on a level and stable

surface with sufficient air circulation.

When placed on heavy carpet, the

product may vibrate slightly.

2. Avoid a location where the sensors are

exposed to direct breeze or draft if the

product has sensors. The product may

not operate properly.

3. Avoid use in locations where furniture,

fabrics, or other items may come in

contact with and restrict the air inlets

and/or outlets.

4. Avoid locations exposed to direct

sunlight. It may cause to change shape

or color of the product.

5. Avoid locations where the product is

exposed to condensation or drastic

changes in temperature. Use under

appropriate conditions between 32 - 95

ºF (0 – 35 ºC).

6. Avoid use in locations where greasy

or oily smoke is generated. (such as in

a kitchen, etc.). The main unit surface

may crack and the sensors may

malfunction as a result.

7. The dust collecting ability of the product

is effective even when the product is

as close to 1.2 inches (3 cm) from the

wall, but the surrounding walls or floor

may get dirty. Please place the product

at a distance from the wall.

The wall directly behind the air outlets

and the floor or rug on which the

product placed may become dirty over

time. When using the product for an

extended period of time at the same

location, periodically clean the walls,

the floor or the rug.

CAUTIONS CONCERNING

FILTER

1. Follow the instructions in this manual

for filter installation and maintenance.

(Page 9,13,14)

2. Take out the filters from the plastic bag

before placing the filter in the main unit.

3. Do not operate the product without the

filters properly installed.

4. Do not wash and reuse the True HEPA

filter and the Active carbon deodorizing

filter.

Washing will not improve filter

performance and can also cause

electric shock or operating

malfunctions.

5. Do not operate the product in a rooms

where aerosol insecticides are present.

It may cause the odor of insecticide

may be remained in the product and

emitted from the air outlets.

CAUTIONS CONCERNING

OPERATION

1. Do not block the air inlets or air outlets.

2. Always operate the product in an

upright position.

3. Always hold the handle of the product

when moving it.

4. Always lift up the product when moving

it on easily damaged flooring, an

uneven surface, or carpet.

IMPORTANT SAFETY INSTRUCTIONS 2

FX-J80U_3rd_EN.indd 5FX-J80U_3rd_EN.indd 5 2021/09/29 11:39:102021/09/29 11:39:10

EN-6

CAUTIONS CONCERNING

MAINTENANCE

1. Follow the instructions in this manual

for maintenance. (Page 13 - 15)

2. Clean the exterior with a soft cloth only.

3. Do not use volatile fluids and/or

detergents.

The main unit surface may be

damaged or cracked with strong

corrosive cleansers, benzine, paint

thinner, polishing powder or grease. In

addition, the sensors may malfunction

as a result if the product has sensors.

4. Do not scrub the back panel (pre-filter)

hard during its maintenance.

5. When replacing filters or any

accessories, use specified parts in this

manual.

IMPORTANT SAFETY INSTRUCTIONS 3

FX-J80U_3rd_EN.indd 6FX-J80U_3rd_EN.indd 6 2021/09/29 11:39:112021/09/29 11:39:11

EN-7

ENGLISH

PART NAMES 1

(FRONT)

(BACK)

1514

1 2

1Operation Panel

2Air Outlet (Front / Back)

3Air Quality Monitor

4Front Display

5Main Unit

6Handle

(2 locations: Left and Right)

7Front Louver

8Back Panel (Pre-Filter)

9Air Inlet

10 Active Carbon Deodorizing Filter

11 True HEPA Filter

Sensor Filter

Sensor (Internal)

Odor / Sensitive dust /

Temperature / Humidity

13 Unit*

(Plasmacluster Ion Generating Unit)

14 Unit* Holder

15 Unit* Cover

16 Unit* Cleaning Brush

17 Power Cord, Plug

* The Unit refers to Plasmacluster Ion

Generating Unit.

FX-J80U_3rd_EN.indd 7FX-J80U_3rd_EN.indd 7 2021/09/29 11:39:122021/09/29 11:39:12

EN-8

FRONT DISPLAY

OPERATION PANEL Press either button with “ ” to start.

12345678

21 22201918171615141312

1POWER ON/OFF Button

2Wi-Fi Button ()

3AUTO Button, Indicator Light - white

4PLASMACLUSTER EXPRESS CLEAN

Button, Indicator Light - white

5Plasmacluster Ion SPOT Button,

Indicator Light - white

Fan Speed Button, Indicator Lights - white

(Press 3 sec.*)

Plasmacluster Ion ON/OFF Button

7TIMER Button

(Press 3 sec.*) FILTER RESET Button

8DISPLAY Button

(Press 3 sec.*) CHILD-LOCK Button

9Child-Lock Indicator Light - white

10 Light Sensor

Air Quality Monitor

Indicates the air purity of the room in 5 levels with

color changes.

12 Wi-Fi Indicator ()

SHARP CLOUD Indicator ( )

PM2.5 Monitor

Indicates the sensitive dust sensor detects microscopic

dust.

TURN OFF Orange Red

Clean Impure

Blue

Clean

Red

Impure

Dust Monitor

Odor Monitor

Continuously monitors dust or odor in the air and changes

color depending on purity.

TURN OFF Orange Red

Clean Impure

17 Unit Replacement Indicator

18 Filter Maintenance Indicator

19 ON Timer Indicator

20 OFF Timer Indicator

21 Plasmacluster Ion Indicator

DISPLAY

The displayed numbers are approximate values.

•PM2.5 Monitor

PM2.5 10μg/m3 to 499μg/m3 is displayed.

•Wattage Monitor

Indicates wattage by current operation.

•Humidity Monitor

Humidity 20% to 90% is displayed.

•Temperature Monitor

Temperature 32oF to 122oF is displayed.

• Timer Monitor

Indicates setting time or remaining

time of ON/OFF timer.

500μg/m3

or more

9μg/m3

or less

20%

or less 90%

or more

123oF

or more

31oF

or less

For details on items marked with ( ), refer to the Wi-Fi Connect Guide.

* Press and hold 3 seconds or longer.

PART NAMES 2

FX-J80U_3rd_EN.indd 8FX-J80U_3rd_EN.indd 8 2021/09/29 11:39:212021/09/29 11:39:21

EN-9

ENGLISH

4. Install the back panel.

5. Record the date when you start or

replace the filters on the back cover

of this manual.

Click

Active Carbon Deodorizing Filter

Filtro desodorizante de carbón activo

Model

Modelo

Starting date of use

Fecha de comienzo de uso

. . . .

True HEPA Filter

Filtro true HEPA

Model

Modelo

Starting date of use

Fecha de comienzo de uso

. . . .

FZ-J80HFU

FZ-J80DFU

1. Remove the back panel.

2. Take out the filters from the plastic

bag.

3. Install the filters in the correct order

as shown.

Back panel

True HEPA Filter

Active Carbon

Deodorizing Filter

•To maintain the quality of the filter, it is installed in the main unit and packaged in a

plastic bag.

•Be sure to stop operation and unplug the product before filter installation or replacement.

• Do not operate the product without the filters.

FILTER INSTALLATION

NOTE

True HEPA Filter

Active Carbon

Deodorizing Filter

FX-J80U_3rd_EN.indd 9FX-J80U_3rd_EN.indd 9 2021/09/29 11:39:262021/09/29 11:39:26

EN-10

• The product emits high density Plasmacluster ions

only in the forward direction.

• The product produces stronger air for 8 hours. When

the operation finishes, the product will return to its

prior operation mode.

• The Plasmacluster Ion Mode cannot be turned “OFF”.

PLASMACLUSTER ION

SPOT MODE

START/STOP

FAN SPEED BUTTON

SLEEP:

The product will operate quietly, and the fan speed

will automatically switch depending on the amount

of impurities in the air and room brightness.

The front display and air quality monitor automatically

switches dims or turns OFF based on room

brightness.

Room is bright: light is dimmed

Room is dark: light is OFF

POLLEN:

The dust sensor is automatically increased and

quickly detects impurities such as dust and pollen

and cleans the air powerfully.

START STOP

OPERATION 1

♪

AUTO MODE

The fan speed is automatically controlled

depending on the 3 detections. (Dust / Odor / Light)

• Unless the power plug has been unplugged, the

operation will Auto Resume in the previous mode

it was operating in.

Example: if the power is lost during operation, the

operation will resume to previous operation mode

and settings if power is restored.

♪

♪♪

POLLEN

SLEEP

LOW

MED

MAX

♪

The air purifier releases Plasmacluster ions at max

air flow for 10 minutes. After that, it operates for 50

minutes on high fan speed.

• When the operation finishes after 60 minutes, the

product will return to the prior operation mode.

It is able to change to other modes during this

operation.

• The Plasmacluster ion cannot be turned “OFF”.

PLASMACLUSTER

EXPRESS CLEAN

MODE

♪

OPERATION 1

NOTE

•When light control is set to “Auto”, front display,

air quality monitor will automatically switch ON or

dims based on room brightness. (Page 12)

NOTE

♪

FX-J80U_3rd_EN.indd 10FX-J80U_3rd_EN.indd 10 2021/09/29 11:39:382021/09/29 11:39:38

EN-11

ENGLISH

OPERATION 2

♪

♪♪

Humidity

Wattage

PM2.5 level

Temperature

CHILD LOCK

PLASMACLUSTER ION

ON/OFF

The operation panel will be locked.

When the Plasmacluster function is ON, the

Plasmacluster ion indicator light is on. (Page 8)

(with the product ON)

Press for 3 sec.

♪

Press for 3 sec.

♪

Press for 3 sec.

♪♪

Press for 3 sec.

♪♪

CANCELLATION

OFF

SELECTING DISPLAY

Set the ON TIMER when you would like to schedule

the air purifier to turn on after a certain number of

hours.

• If you have already set the timer using the App,

you cannot set the timer using the product.

• If you have already set the timer using the App,

you cannot set the timer using the product.

Set the OFF TIMER when you would like to

schedule the air purifier to turn off after a certain

number of hours.

ON TIMER

OFF TIMER

(with the product OFF)

(with the product ON)

Front Display

……

♪ ♪ ♪ ♪ ♪♪

1hour 2hour 3hour 12hour

Cancellation

……

♪ ♪ ♪ ♪ ♪♪

1hour 2hour 3hour 12hour

Cancellation

NOTE

• Every time you press the TIMER button, it

will change the auto start time in the following

sequence:

•Every time you press the TIMER button, it will

change the auto shutdown time in the following

sequence: • It is possible to turn Wi-Fi off while in Child Lock

Mode.

NOTE

FX-J80U_3rd_EN.indd 11FX-J80U_3rd_EN.indd 11 2021/09/29 11:39:502021/09/29 11:39:50

EN-12

1. Turn the product OFF.

2. Select

Set

Press for 3 sec.

♪

HOW TO CHANGE VARIOUS SETTINGS

You can change the functions listed in the table below.

Function ( ) Setting ( )

Light control

You can select the brightness of the front display

and air quality monitor.

Turn off *

Dim

Auto (default)

Light automatically switches based on room brightness.

Room

brightness

Front Display and Air Quality Monitor

ALL MODE

(Except SLEEP) SLEEP MODE

Bright ON Dim

Dark Dim Turn o

Auto resume

This model has Auto Resume function, where

the operation resumes at the previous operation

mode and settings if the power is restored.

Cancellation

ON (default)

Adjusting sensor sensitivity (F3-F5)

For details, refer to Page 16.

Light sensor Low

Sensitive dust sensor Standard (default)

Odor sensor High

*When set to “Turn off”, the “Dim” light illuminates for 8 seconds after operation starts and then the light turns off.

3. Select “Function Number”.

GO BACK GO FORWARD

Set ♪

4. Select “Setting Number”.

GO BACK GO FORWARD

Set ♪～

5. Finish the setting.

♪♪

････

♪♪

Turn off

♪～

OPERATION 3

For details on selecting A, refer to

Page 19 - 21.

See below table for

functions.

See below table for

settings.

♪

♪*

Product

setting

Wi-Fi

setting

• You can select F or A.

FX-J80U_3rd_EN.indd 12FX-J80U_3rd_EN.indd 12 2021/09/29 11:40:132021/09/29 11:40:13

EN-13

ENGLISH

Wipe with a dry, soft cloth

Remove the dust gently with a

cleaning tool such as a vacuum

cleaner.

MAIN UNIT / BACK PANEL

Back panel

(Pre-filter)

•To maintain optimum performance of this air puri er, please clean the product including

the  lter periodically.

• Be sure to stop operation and unplug the product before any maintenance or replacing

accessories.

FILTER MAINTENANCE INDICATOR

The filter maintenance indicator light will turn on* when it is time to maintain the back panel (pre-filter) .

*This indicator light will turn on after approximately 720 hours operating. (30 days × 24 hours = 720 hours)

After maintenance, connect the power plug to the wall outlet and press POWER ON/OFF button, then TIMER

button for 3 seconds.

MAINTENANCE

RESET

Press for 3 sec.

Turn off

How to clean hard to remove dirt.

Back panel

1. Add a small amount of neutral detergent to

water and soak for about 10 minutes.

Do not apply excessive pressure when

scrubbing the back panel.

2. Rinse off the neutral detergent with clean water.

3. Completely dry the filter in a wellventilated area.

Sensor  lter

1. Remove the back panel.

2. Remove the sensor filter.

3. If the sensor filter is very dirty, wash it

with water and dry it thoroughly.

Sensor

filter

NOTE

CARE AND MAINTENANCE 1

♪

When the filter maintenance

indicator light turns on.

FX-J80U_3rd_EN.indd 13FX-J80U_3rd_EN.indd 13 2021/09/29 11:40:222021/09/29 11:40:22

EN-14

TRUE HEPA FILTER /

ACTIVE CARBON DEODORIZING FILTER

CARE AND MAINTENANCE 2

Remove the dust on the filters.

Some odors absorbed by the filters will break down over time, causing additional odors. Depending on usage conditions, and

especially if the product is used in environments significantly more severe than a normal household, these odors may become

noticeable sooner than expected.

Replace the filter in those cases or if dust is unable to be removed after maintenance.

Disposal of Filters

Please dispose of the replaced filter according to the local disposal laws and regulations.

Filter Name Maintenance Cycle Max Service Life Replacement Filter Model

True HEPA Filter Whenever dust accumulates, when

odor emanates from the air outlet, or

once a month.

2 years*1, 2

FZ-J80HFU

Active Carbon

Deodorizing Filter FZ-J80DFU

*¹ According to Japan Electric Manufacture’s Association JEM 1467, the Max service life is based on the equivalent condition

of the smoke from 5 cigarettes per day whereby the dust collection/deodorization power is reduced by half compared with

that of new filter. It is recommended to replace the filter more frequently under more severe conditions.

*² Designated App notifies when filters or Plasmacluster ion generating unit should be replaced according to usage.

NOTE

See page 9 for directions on how to

install the lter when replacing.

• Please consult your dealer for purchase of

replacement lter.

• Use only lter designed for this product.

FZ-J80HFU: 1 unit FZ-J80DFU: 1 unit

Record the date when you replace the lters on

the back cover of this manual.

REPLACEMENT AND MAINTENANCE CYCLE

MAINTENANCE

REPLACEMENT

Do not wash the lters. Do not expose to sunlight.

(Otherwise these lters may lose ecacy.)

Tag

TRUE HEPA FILTER

Maintain only the tagged

surface. Do not clean up

the opposite surface.

The filter is fragile, so be

careful not to apply too

much pressure.

ACTIVE CARBON DEODORIZING FILTER

Both surfaces can be

maintained.

The filter is fragile, so be

careful not to apply too much

pressure.

Scan the QR code for

product information and

accessories.

FX-J80U_3rd_EN.indd 14FX-J80U_3rd_EN.indd 14 2021/09/29 11:40:262021/09/29 11:40:26

EN-15

ENGLISH

CARE AND MAINTENANCE 3

When the total operation time exceeds 17,500 hours, the unit replacement indicator will ash to indicate that the

Plasmacluster ion generating unit needs replacement.

Operating time

17,500 hours

Flash slowly

Replace the Plasmacluster ion generating unit

19,000 hours

Flash quickly

Stop the emission of the Plasmacluster ions.

* The replacement time is not related to the selected operation mode.

Consult your dealer when purchasing a replacement Plasmacluster ion generating unit.

Model: IZ-C90MU

Disposal of Plasmacluster Ion Generating Unit

Dispose of used Plasmacluster ion generating unit according to local laws and regulations.

①

②

①

1. Remove the unit cover,

and pull out the unit

holder.

2. Remove dusts from the

electrode section.

3. Insert the unit holder

in the main unit, and

install the unit cover.

• Do not clean with anything other than the unit cleaning brush. Doing so could lead to failures in the unit.

• A bent electrode could be cut off and dropped during the cleaning process, but it will not change the performance.

• Do not touch the electrode directly. Doing so could lead to pain/itching.

• Do not transform the electrode section. Doing so can damage it.

• Do not touch the connection terminals. Doing so can damage them.

PLASMACLUSTER ION GENERATING UNIT

(electrode section)

Unit cleaning brush

Electrode Around the base

Before cleaning After

cleaning

MAINTENANCE

UNIT REPLACEMENT INDICATOR

REPLACEMENT

Remove the claw of unit holder (

and remove the Plasmacluster ion

generating unit (

NOTE

FX-J80U_3rd_EN.indd 15FX-J80U_3rd_EN.indd 15 2021/09/29 11:40:312021/09/29 11:40:31

EN-16

TROUBLESHOOTING

Odor and smoke persists.

• Check the filters. If they appear to be extremely

dirty, clean or replace them.

Air discharged from the product

has an odor.

• Check to see if the filters are extremely dirty.

Clean or replace the filters.

The product does not operate

when cigarette smoke is in the air.

• Make sure the product is installed in a location in

which the sensors can detect cigarette smoke.

•Check to see if the sensitive dust sensor openings

are blocked or clogged. If they are blocked or

clogged, clean the sensor filter or the back panel.

Smell from a new filter.

• Immediately after removing the plastic bag, a

slight odor may occur.

This odor is not harmful for filter performance or

human exposure.

The product makes a clicking or

ticking sound.

• The product may make clicking or ticking sounds

when it is generating ions.

The air quality monitor is blue

even when the air is not clean.

• The air may have been dirty when the product

was plugged in. Unplug the product, wait one

minute, and then plug the product in again.

The air quality monitor is red even

when the air is clean.

• Dirty or clogged the sensitive dust sensor

openings interfere with sensor operation. Gently

clean the sensor filter or the back panel.

The air quality monitor changes

color frequently.

• The air quality monitor automatically changes

color when the sensitive dust sensor and odor

sensor detect impurities. If you are concerned

about the change, you can change sensor

sensitivity. (Page 12)

The filter maintenance indicator

light is on.

• Whenever after performing maintenance of the

filters, connect the power cord to an outlet and

press POWER ON/OFF button, then press the

FILTER RESET button. (Page 13)

The front display is turned off.

• When light control is set to “Turn off”, the light is

always off. If you do not want the light to be off,

set light control to “Auto” or “Dim” setting.

(Page 12)

The product’s display does not

match weather report or another

hygrometer or thermometer in the

room.

• Outdoor and indoor as well as the home

environment (the volume of traffic nearby, number

of stories in home, etc.) may cause a reading

different than those data.

• There is a difference in the level within the same

room.

When should sensor sensitivity be

changed?

Please change sensor sensitivity as follows according

to each case.

Light sensor

• Change to “Low” when the front display still

lights up brightly even if it turns dark in the

room.

• Change to “High” when the front display lights

up dark even if it is bright in the room.

Sensitive dust sensor

• Change to “Low” when PM2.5, Dust or Air

Quality Monitor displays in red frequently.

• Change to “High” when PM2.5 or Dust Monitor

doesn’t light up or Air Quality Monitor stays in

blue even if it is dusty in the room.

Odor sensor

• Change to “Low” when Odor Monitor displays in

red frequently.

• Change to “High” when Odor Monitor doesn’t

light up even if there is some odor in the room.

Before calling for service, please review the list below, since the problem may not be the

product malfunction.

FX-J80U_3rd_EN.indd 16FX-J80U_3rd_EN.indd 16 2021/09/29 11:40:312021/09/29 11:40:31

EN-17

ENGLISH

ERROR DISPLAY

Flash quickly

• The communication between

SHARP server and the air purifier is

not available.

Please check the Wi-Fi Connect

Guide for details.

• Is the Plasmacluster ion generating

unit inserted properly?

⇒Pull out the Plasmacluster ion

generating unit and insert it to the

end again, and then operate again.

• The concentration of Plasmacluster

ion is descending.

⇒Maintain the electrode section of

the Plasmacluster ion generating

unit. (Page 15)

•Unplug the product, wait one minute,

and then plug the product in again.

Model FX-J80U

Power supply 120 V / 60 Hz

Fan Speed Operation

Fan Speed Adjustment MAX MED SLEEP

Rated Power (W) 70 27 3.2

Fan Speed (CFM) 321 170 35

Noise Level (dBA)*1 49 45 15

Standby Power (W) 0.9 (When Wi-Fi adapter is ON.)

0.7 (When Wi-Fi adapter is OFF.)

Recommended Room Size*2 502 sq. ft. (47 m2)

CADR (Dust / Smoke / Pollen) 334 / 324 / 361

Filter type Dust collection True HEPA Filter

Deodorization Active Carbon Deodorizing Filter

Cord Length 6.6 ft. (2.0m)

Dimensions 16.4 in. (W) × 11.5 in. (D) × 28.7 in. (H)

(416 mm (W) × 291 mm (D) × 728 mm (H))

Weight 23.8 lbs. (10.8 kg)

Standby Power This product consumes a minimal amount of power while in standby mode.

For energy saving, unplug the power cord when the product is not in use.

*1 Noise level is measured based on the JEM 1467 standard of the Japan Electrical

Manufacturers’ Association.

*2 Size of a room which is appropriate for operating the product at maximum fan speed.

SPECIFICATIONS

FX-J80U_3rd_EN.indd 17FX-J80U_3rd_EN.indd 17 2021/09/29 11:40:372021/09/29 11:40:37

EN-18

OTHER SETTINGS 1

SAFETY / PRECAUTIONS

WARNING

In case of remote operation from outside, you

may not be able to check air purier current

condition or the area around it and the situation

concerning anyone possibly staying there, so

please adequately conrm safety before use.

• Make sure the electric plug is fully inserted into a

power socket, and there is no dust on the plug or in

the socket hole. (It may cause heat, combustion,

re, etc., due to poor contact or contact failure)

• Make sure beforehand that although there are

some wind changes, no negative impact will occur to

the environment inside the room. (such as whether

there is anything ying easily in the wind)

Because the wind may cause something to fall

down, resulting in res, wounds, defacement of

household belongings.

CAUTION FOR USE

• Agreement with “Terms of Service” is needed to use

App.

• App will be periodically revised because of version

upgrade.

• Screens and illustrations in this book are for

explanation, there are some dierences to the real

product.

• In the case of bad connection, the App may not be

able to control the air purier. The current operation

of the air purier may not be accurately reected on

the App.

• Locking smartphone display is recommended to

avoid wrong operation.

•Although the App is free, communications expenses

for download of dedicated App and operation with

smartphone or tablet are customer’s obligation.

CAUTION FOR Wi-Fi

Caution for usage about electrical wave

• In case of the usage at the following place, the

operation cannot be guaranteed : Near Bluetooth®

wireless communications device using the same

frequency (2.4GHz) as this product or specied

low power wireless device. Also in the place like

magnetic eld of the device such as microwave

oven, or the place with static electricity or the

place radio disturbance is occurred, it may not be

available temporarily due to weak electrical wave.

• Wireless connection and performance cannot be

guaranteed for all routers or housing environment.

At the following places, it is likely electrical wave

cannot reach or is disconnected: Inside of the

building made with concrete, reinforcing steel or

metal / near the obstruction / near the wireless

communications device applying the same

frequency.

• Wi-Fi of this product corresponds to channel 1 - 13.

It’s not available to communicate with the routers

set up to other channels.

Caution for personal information

(related to Security)

•Using Wi-Fi device has the possibility of interception

as long as using electrical wave regardless of

secret code setting.

• Wi-Fi has the advantage of free LAN connection

in the service area because of the communication

between this product and the router applying

electrical wave. On the other side, intercept of

communication or unfair intrusion are likely to occur

because electrical wave reaches everywhere in the

certain area through the obstructions (e.g. walls).

• Do not connect to the device or network without

App to authority.

• The Wi-Fi function of this product should be

initialized in case of disposal or handover to a third

person.

• The Wi-Fi function of the unit should be initialized in

case of handover from a third person to avoid illegal

access of outsider.

Please refer to the Wi-Fi Connect Guide

for how to connect and pair your smart

device to your product.

How to set Wi-Fi ON / OFF after

completing the initial settings

When turning off Wi-Fi

When turning on Wi-Fi again

Refer to Page 4 - 7 of the air purifier Wi-Fi

Connect Guide and set up the connection with the

router again.

•If the product is already registered to your smartphone,

you do not need to register again.

• Wi-Fi ON / OFF can also be set from

“ : Wi-Fi adapter ON/OFF”. (Page 19)

In this case, Wi-Fi connection with the router will

be automatically restored.

• Reconnection to the Wireless Router may take a

few minutes to complete, after turning Wi-Fi on

again.

Press for 3 sec.

♪～

Go off

NOTE

FX-J80U_3rd_EN.indd 18FX-J80U_3rd_EN.indd 18 2021/09/29 11:40:412021/09/29 11:40:41

EN-19

ENGLISH

OTHER SETTINGS 2

HOW TO CHANGE VARIOUS SETTINGS 1

Step 1. Turn the

product OFF.

Step 2.

Step 3. Select .

Step 4. Select “Function Number”.

GO BACK GO FORWARD

No Function Page

Wi-Fi adapter ON/OFF 19

Wi-Fi connection with a router 19

Link settings with a smartphone 20

Initialization of Wi-Fi function 20

Update 20

Confirmation of MAC address 20

Display Wi-Fi network status 21

AP(Access Point) mode 21

Step 5. Please refer to page 19 - 21

for the detail of each functions.

Step 6. Finish the setting.

♪

Press for

3 sec.

♪

････

Turn off

♪～

You can change the functions in the table below.

Follow Steps 1 - 4 to select the Function.

♪ ♪

1. Select by following Steps 1 - 4.

2. Select “Setting Number”.

3. Complete ♪

♪

OFF: Stoppage of Wi-Fi function

ON: Start the Wi-Fi function

1. Select by following Steps 1 - 4.

2. After is displayed, press the

Wi-Fi Protected Setup (WPS) button

of the router.

Once connected, receiver level will be displayed.

A connection error is occuring if is displayed.

Please confirm the router and try again.

3. Complete

♪

weak strong Light up

• When is selected, the square rotates

on the display until the setting is completed.

When setting is completed, is displayed.

Wi-Fi adapter ON/OFF

Wi-Fi connection with a

router

Set ♪

♪Set ♪

Blink Blink

FX-J80U_3rd_EN.indd 19FX-J80U_3rd_EN.indd 19 2021/09/29 11:41:102021/09/29 11:41:10

EN-20

OTHER SETTINGS 3

1. Select by following Steps 1 - 4

on page 19.

2. After is displayed, start the App

and register the air purifier.

A connection error is occuring if is displayed.

Please confirm the router and try again.

3. Complete ♪

♪～

Complete

Blink

Setting up

1. Start the App then tap “ ” at the

“Home” screen and select “Update”.

2. Select by following Steps 1 - 4

on page 19.

3. will be displayed.

4. Follow instructions on the App

screen.

will be blinking during update.

A connection error is occuring if is displayed.

Please confirm the router and try again.

5. Air purifier will automatically

go off after completion of the

update. Go off

It may take a few minutes to complete the update.

1. Select by following Steps 1 - 4

on page 19.

2. After is displayed press “AUTO”

button.

A connection error is occuring if is displayed.

Please confirm the router and try again.

3. Complete

• Please delete the device registration from the

App when initializing the air purifier which is

already connected to the Wi-Fi.

♪～

Complete

Blink

Initializing

♪

1. Select by following Steps 1 - 4

on page 19.

2. Press Plasmacluster Express Clean

button to display MAC address.

3. Complete ♪

Initialization of Wi-Fi

function

Link settings with a

smartphone Update

Confirmation of MAC

address

HOW TO CHANGE VARIOUS SETTINGS 2

For example :

In case MAC address is “12 : 34 : 56 : AB : CD : EF”

♪♪♪♪♪♪♪ ♪～

FX-J80U_3rd_EN.indd 20FX-J80U_3rd_EN.indd 20 2021/09/29 11:41:362021/09/29 11:41:36

ENGLISH

EN-21

OTHER SETTINGS 4

1. Select by following Steps 1 - 4

on page 19.

2. After displaying for a few

seconds, network status of Wi-Fi

adapter will be displayed.

3. Complete

♪

Connection is stable

Wi-Fi adapter is off

Please turn on Wi-Fi adapter.

Router is not registered

Please perform the Wi-Fi connection with

the router.

Link settings with the App is not performed

Please perform the link setting with the

smartphone.

Wi-Fi adapter network error

Please turn off Wi-Fi adapter and turn on

again after a while.

Network error between the air purifier and

the router

Please confirm the network status of the

router.

Network service error

Please turn off the air purifier and confirm

the internet status, then try again.

1. Select by following Steps 1 - 4

on page 19.

2. Perform Wi-Fi connection of the air

purifier and the router based on the

App screen.

Refer to the App or the Wi-Fi Connect

Guide for further operations.

and blinks while setting the

connection between the product and the router.

Once connected, receiver level will be displayed.

A connection error is occuring if is displayed.

Please confirm the router and try again.

weak strong Light up

Display Wi-Fi network

status AP (Access Point) mode

HOW TO CHANGE VARIOUS SETTINGS 3

SPECIFICATIONS

Wireless LAN: IEEE802.11b/g/n

Frequency range: 2.4GHz frequency band

FX-J80U_3rd_EN.indd 21FX-J80U_3rd_EN.indd 21 2021/09/29 11:41:522021/09/29 11:41:52

Intellectual property rights for this product

ⅰ

■ Software structure

Software installed in this product is structured with multiple independent

software components, each of them has our or third-party's copyright.

■ Software of our development and free software

Among the software components of this product, for software we

developed or created and incidental documents has our copyright. And

they are protected

by copyright law, international regulation and other related laws.

Also this product uses software components distributed as free software

with third-party's copyright.

■ Obligation of license indication

Some software components installed in this product are required to

indicate the license by those copyright holders.

License indications of such software components are as below:

●Expat

Cooper

Permission is hereby granted, free of charge, to any person obtaining a copy of

this software and associated documentation les (the "Software"), to deal in the

Software without restriction, including without limitation the rights to use, copy,

modify, merge, publish, distribute, sublicense, and/or sell copies of the Software,

and to permit persons to whom the Software is furnished to do so, subject to the

following conditions:

The above copyright notice and this permission notice shall be included in all

copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,

EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES

OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND

NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT

HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,

WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING

FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR

OTHER DEALINGS IN THE SOFTWARE.

●Wslay

The MIT License

Permission is hereby granted, free of charge, to any person obtaining a copy of

this software and associated documentation les (the "Software"), to deal in the

Software without restriction, including without limitation the rights to use, copy,

modify, merge, publish, distribute, sublicense, and/or sell copies of the Software,

and to permit persons to whom the Software is furnished to do so, subject to the

following conditions:

The above copyright notice and this permission notice shall be included in all

copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,

EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES

OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND

NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT

HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,

WHETHER IN AN ACTION OF CONTRACT,TORT OR OTHERWISE, ARISING

FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR

OTHER DEALINGS IN THE SOFTWARE.

●libFLAC

Redistribution and use in source and binary forms, with or without modication,

are permitted provided that the following conditions are met:

- Redistributions of source code must retain the above copyright notice, this list of

conditions and the following disclaimer.

- Redistributions in binary form must reproduce the above copyright notice, this

list of conditions and the following disclaimer in the documentation and/or other

materials provided with the distribution.

- Neither the name of the Xiph.org Foundation nor the names of its contributors

may be used to endorse or promote products derived from this software without

specic prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND

CONTRIBUTORS ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS

BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,

OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,

PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,

DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED

AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT

LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN

ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE

POSSIBILITY OF SUCH DAMAGE.

●Iw-IP

Redistribution and use in source and binary forms, with or without modication,

are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list

of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this

list of conditions and the following disclaimer in the documentation and/or other

materials provided with the distribution.

3. The name of the author may not be used to endorse or promote products

derived from this software without specic prior written permission.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS

OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE

LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,

OR CONSEQUENTIAL DAMAGES(INCLUDING, BUT NOT LIMITED TO,

PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,

DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED

AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT

LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN

ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE

POSSIBILITY OF SUCH DAMAGE.

This le is part of the lwIP TCP/IP stack.

Author: Adam Dunkels <[email protected]>

●JSMN

Permission is hereby granted, free of charge, to any person obtaining a copy of

this software and associated documentation les (the "Software"), to deal in the

Software without restriction, including without limitation the rights to use, copy,

modify, merge, publish, distribute, sublicense, and/or sell copies of the Software,

and to permit persons to whom the Software is furnished to do so, subject to the

following conditions:

The above copyright notice and this permission notice shall be included in all

copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,

EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES

OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND

NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT

HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,

WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING

FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR

OTHER DEALINGS IN THE SOFTWARE.

●mbedTLS

Licensed under the Apache License, Version 2.0 (the "License");

you may not use this le except in compliance with the License.

You may obtain a copy of the License at

http://www.apache.org/licenses/LICENSE-2.0

Unless required by applicable law or agreed to in writing, software distributed

under the License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES

OR CONDITIONS OF ANY KIND, either express or implied. See the License for

the specic language governing permissions and limitations under the License.

●wpa supplicant

Redistribution and use in source and binary forms, with or without modication,

are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of

conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this

list of conditions and the following disclaimer in the documentation and/or other

materials provided with the distribution.

3. Neither the name(s) of the above-listed copyright holder(s) nor the names of

its contributors may be used to endorse or promote products derived from this

software without specic prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND

CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE

ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR

CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,

SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT

NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;

LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)

HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN

CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR

OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,

EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

●newLib

(1) Red Hat Incorporated

FP-J80_WIRELESS_知的財産権.indd 2 2018/09/26 14:07:56

Intellectual property rights for this product 1

EN-22

FX-J80U_3rd_EN.indd 22FX-J80U_3rd_EN.indd 22 2021/09/29 11:41:532021/09/29 11:41:53

ENGLISH

ⅱ

This copyrighted material is made available to anyone wishing to use, modify,

copy, or redistribute it subject to the terms and conditions of the BSD License.

This program is distributed in the hope that it will be useful, but WITHOUT

ANY WARRANTY expressed or implied, including the implied warranties of

MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. A copy of this

license is available at

http://www.opensource.org/licenses. Any Red Hat trademarks that are incorporated

in the source code or documentation are not subject to the BSD License and may

only be used or replicated with the express permission of Red Hat, Inc.

(2) University of California, Berkeley

Redistribution and use in source and binary forms, with or without modication,

are permitted provided that the following conditions are met:

* Redistributions of source code must retain the above copyright notice, this list

of conditions and the following disclaimer.

* Redistributions in binary form must reproduce the above copyright notice,

this list of conditions and the following disclaimer in the documentation and/or

other materials provided with the distribution.

* Neither the name of the University nor the names of its contributors may

be used to endorse or promote products derived from this software without

specic prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND

CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE

ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR

CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,

SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT

NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;

LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)

HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN

CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR

OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,

EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

(3) David M. Gay (AT&T 1991, Lucent 1998)

The author of this software is David M. Gay.

Permission to use, copy, modify, and distribute this software for any purpose

without fee is hereby granted, provided that this entire notice is included in all

copies of any software which is or includes a copy or modication of this software

and in all copies of the supporting documentation for such software.

THIS SOFTWARE IS BEING PROVIDED "AS IS", WITHOUT ANY EXPRESS OR

IMPLIED WARRANTY. IN PARTICULAR, NEITHER THE AUTHOR NOR AT&T

MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND CONCERNING

THE MERCHANTABILITY OF THIS SOFTWARE OR ITS FITNESS FOR ANY

PARTICULAR PURPOSE.

-------------------------------------------------------------------

The author of this software is David M. Gay.

Permission to use, copy, modify, and distribute this software and its documentation

for any purpose and without fee is hereby granted, provided that the above

permission notice and warranty disclaimer appear in supporting documentation,

and that the name of Lucent or any of its entities not be used in advertising or

publicity pertaining to distribution of the software without specic, written prior

permission.

LUCENT DISCLAIMS ALL WARRANTIES WITH REGARD TO THIS SOFTWARE,

INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS. IN NO EVENT SHALL LUCENT OR ANY OF ITS ENTITIES BE

LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR

ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA

OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR

OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH

THE USE OR PERFORMANCE OF THIS SOFTWARE.

(4) Advanced Micro Devices

This software is the property of Advanced Micro Devices, Inc (AMD) which

specically grants the user the right to modify, use and distribute this software

provided this notice is not removed or altered. All other rights are reserved by

AMD.

AMD MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH

REGARD TO THIS SOFTWARE. IN NO EVENT SHALL AMD BE LIABLE FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH OR

ARISING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS

SOFTWARE.

So that all may benet from your experience, please report any problems or

suggestions about this software to the 29K Technical Support Center at 800-29-

29-AMD (800-292-9263) in the USA, or 0800-89-1131 in the UK, or 0031-11-1129

in Japan, toll free. The direct dial number is 512-462-4118.

Advanced Micro Devices, Inc.

29K Support Products

Mail Stop 573

5900 E. Ben White Blvd.

Austin, TX 78741

800-292-9263

(7) Sun Microsystems

Developed at SunPro, a Sun Microsystems, Inc. business. Permission to use,

copy, modify, and distribute this software is freely granted, provided that this notice

is preserved.

(8) Hewlett Packard

To anyone who acknowledges that this le is provided "AS IS" without any express

or implied warranty:

permission to use, copy, modify, and distribute this le for any purpose is hereby

granted without fee, provided that the above copyright notice and this notice

appears in all copies, and that the name of Hewlett-Packard Company not be used

in advertising or publicity pertaining to distribution of the software without specic,

written prior permission. Hewlett-Packard Company makes no representations

about the suitability of this software for any purpose.

(9) Hans-Peter Nilsson

Permission to use, copy, modify, and distribute this software is freely granted,

provided that the above copyright notice, this notice and the following disclaimer

are preserved with no changes.

THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR

IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE.

(11) Christopher G. Demetriou

Redistribution and use in source and binary forms, with or without modication,

are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of

conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this

list of conditions and the following disclaimer in the documentation and/or other

materials provided with the distribution.

3. The name of the author may not be used to endorse or promote products

derived from this software without specic prior written permission.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS

OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE

LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,

OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,

PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,

DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED

AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT

LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN

ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE

POSSIBILITY OF SUCH DAMAGE.

(12) SuperH, Inc.

This software is the property of SuperH, Inc (SuperH) which specically grants the

user the right to modify, use and distribute this software provided this notice is not

removed or altered. All other rights are reserved by SuperH.

SUPERH MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,

WITH REGARD TO THIS SOFTWARE. IN NO EVENT SHALL SUPERH BE

LIABLE FOR INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL

DAMAGES IN CONNECTION WITH OR ARISING FROM THE FURNISHING,

PERFORMANCE, OR USE OF THIS SOFTWARE.

So that all may benet from your experience, please report any problems or

suggestions about this software to the SuperH Support Center via e-mail at

[email protected] .

SuperH, Inc.

405 River Oaks Parkway

San Jose

CA 95134

USA

(13) Royal Institute of Technology

(Royal Institute of Technology, Stockholm, Sweden).

FP-J80_WIRELESS_知的財産権.indd 3 2018/09/26 14:07:56

Intellectual property rights for this product 2

EN-23

FX-J80U_3rd_EN.indd 23FX-J80U_3rd_EN.indd 23 2021/09/29 11:41:542021/09/29 11:41:54

Intellectual property rights for this product

ⅲ

Redistribution and use in source and binary forms, with or without modication,

are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of

conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this

list of conditions and the following disclaimer in the documentation and/or other

materials provided with the distribution.

3. Neither the name of KTH nor the names of its contributors may be used to

endorse or promote products derived from this software without specic prior

written permission.

THIS SOFTWARE IS PROVIDED BY KTH AND ITS CONTRIBUTORS ``AS

IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT

LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT

SHALL KTH OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,

INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES

(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE

GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS

INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,

WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING

NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE

OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH

DAMAGE.

(14) Alexey Zelkin

Redistribution and use in source and binary forms, with or without modication,

are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list

of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this

list of conditions and the following disclaimer in the documentation and/or

other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS

``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT

NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT

SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,

INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL

DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF

SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;

OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY

OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT

(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF

THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGE.

(15) Andrey A. Chernov

Redistribution and use in source and binary forms, with or without modication,

are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of

conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this

list of conditions and the following disclaimer in the documentation and/or other

materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS

OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR

CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,

SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT

NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;

LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)

HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN

CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR

OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,

EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

(16) FreeBSD

Redistribution and use in source and binary forms, with or without modication,

are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of

conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this

list of conditions and the following disclaimer in the documentation and/or other

materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS

``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT

NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT

SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,

INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL

DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF

SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;

OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY

OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT

(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF

THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGE.

(17) S. L. Moshier

Author: S. L. Moshier.

Permission to use, copy, modify, and distribute this software for any purpose

without fee is hereby granted, provided that this entire notice is included in all

copies of any software which is or includes a copy or modication of this software

and in all copies of the supporting documentation for such software.

THIS SOFTWARE IS BEING PROVIDED "AS IS", WITHOUT ANY EXPRESS

OR IMPLIED WARRANTY. IN PARTICULAR, THE AUTHOR MAKES NO

REPRESENTATION OR WARRANTY OF ANY KIND CONCERNING THE

MERCHANTABILITY OF THIS SOFTWARE OR ITS FITNESS FOR ANY

PARTICULAR PURPOSE.

(18) Citrus Project

Redistribution and use in source and binary forms, with or without modication,

are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of

conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this

list of conditions and the following disclaimer in the documentation and/or other

materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS

``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT

NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT

SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,

INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL

DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF

SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;

OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY

OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT

(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF

THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGE.

(19) Todd C. Miller

Redistribution and use in source and binary forms, with or without modication,

are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of

conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this

list of conditions and the following disclaimer in the documentation and/or other

materials provided with the distribution.

3. The name of the author may not be used to endorse or promote products

derived from this software without specic prior written permission.

THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED

WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE

LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,

OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,

PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,

DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED

AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT

LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN

ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE

POSSIBILITY OF SUCH DAMAGE.

(26) Mike Barcroft

Redistribution and use in source and binary forms, with or without modication,

are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of

conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this

list of conditions and the following disclaimer in the documentation and/or other

materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS

``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT

NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT

SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,

INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL

DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF

FP-J80_WIRELESS_知的財産権.indd 4 2018/09/26 14:07:56

Intellectual property rights for this product 3

EN-24

FX-J80U_3rd_EN.indd 24FX-J80U_3rd_EN.indd 24 2021/09/29 11:41:552021/09/29 11:41:55

ENGLISH

ⅳ

SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;

OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY

OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT

(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF

THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGE.

(35) - ARM Ltd (arm and thumb variant targets only)

Redistribution and use in source and binary forms, with or without modication,

are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list

of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this

list of conditions and the following disclaimer in the documentation and/or other

materials provided with the distribution.

3. The name of the company may not be used to endorse or promote products

derived from this software without specic prior written permission.

THIS SOFTWARE IS PROVIDED BY ARM LTD ``AS IS'' AND ANY EXPRESS OR

IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL ARM LTD BE LIABLE

FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,

OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,

PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,

DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED

AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT

LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN

ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE

POSSIBILITY OF SUCH DAMAGE.

(41) Ed Schouten - Free BSD

Redistribution and use in source and binary forms, with or without modication,

are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of

conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this

list of conditions and the following disclaimer in the documentation and/or other

materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS

``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT

NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT

SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,

INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL

DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF

SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;

OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY

OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT

(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF

THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGE.

●libgloss

(1) Red Hat Incorporated

This copyrighted material is made available to anyone wishing to use, modify,

copy, or redistribute it subject to the terms and conditions of the BSD License. This

program is distributed in the hope that it will be useful,

but WITHOUT ANY WARRANTY expressed or implied, including the implied

warranties of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.

A copy of this license is available at http://www.opensource.org/licenses. Any Red

Hat trademarks that are incorporated in the source code or documentation are not

subject to the BSD License and may only be used or replicated with the express

permission of Red Hat, Inc.

(2) University of California, Berkeley

Redistribution and use in source and binary forms, with or without modication,

are permitted provided that the following conditions are met:

* Redistributions of source code must retain the above copyright notice, this list

of conditions and the following disclaimer.

* Redistributions in binary form must reproduce the above copyright notice,

this list of conditions and the following disclaimer in the documentation and/or

other materials provided with the distribution.

* Neither the name of the University nor the names of its contributors may

be used to endorse or promote products derived from this software without

specic prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND

CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE

ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR

CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,

SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT

NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;

LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)

HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN

CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR

OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,

EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

(3) DJ Delorie

Redistribution, modication, and use in source and binary forms is permitted

provided that the above copyright notice and following paragraph are duplicated in

all such forms.

This le is distributed WITHOUT ANY WARRANTY; without even the implied

warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.

(4) (formerly GPL for fr30)

The GPL is no longer applicable to the fr30 platform. The piece of code (syscalls.c)

referencing the GPL has been ofcially relicensed.

(5) Advanced Micro Devices

This software is the property of Advanced Micro Devices, Inc (AMD) which

specically grants the user the right to modify, use and distribute this software

provided this notice is not removed or altered. All other rights are reserved by

AMD.

AMD MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH

REGARD TO THIS SOFTWARE. IN NO EVENT SHALL AMD BE LIABLE FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH OR

ARISING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS

SOFTWARE.

So that all may benet from your experience, please report any problems or

suggestions about this software to the 29K Technical Support Center at

800-29-29-AMD (800-292-9263) in the USA, or 0800-89-1131 in the UK,

or 0031-11-1129 in Japan, toll free. The direct dial number is 512-462-4118.

Advanced Micro Devices, Inc.

29K Support Products

Mail Stop 573

5900 E. Ben White Blvd.

Austin, TX 78741

800-292-9263

(8) Sun Microsystems

Developed at SunPro, a Sun Microsystems, Inc. business.

Permission to use, copy, modify, and distribute this software is freely granted,

provided that this notice is preserved.

(9) Hewlett Packard

To anyone who acknowledges that this le is provided "AS IS" without any express

or implied warranty:

permission to use, copy, modify, and distribute this le for any purpose is hereby

granted without fee, provided that the above copyright notice and this notice

appears in all copies, and that the name of Hewlett-Packard Company not be used

in advertising or publicity pertaining to distribution of the software without specic,

written prior permission. Hewlett-Packard Company makes no representations

about the suitability of this software for any purpose.

(10) Hans-Peter Nilsson

Permission to use, copy, modify, and distribute this software is freely granted,

provided that the above copyright notice, this notice and the following disclaimer

are preserved with no changes.

THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR

IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE.

(14) - National Semiconductor Corporation

The authors hereby grant permission to use, copy, modify, distribute, and license

this software and its documentation for any purpose, provided that existing

in any distributions. No written agreement, license, or royalty fee is required for

any of the authorized uses.

Modications to this software may be copyrighted by their authors and need not

follow the licensing terms described here, provided that the new terms are clearly

indicated on the rst page of each le where they apply.

FP-J80_WIRELESS_知的財産権.indd 5 2018/09/26 14:07:56

Intellectual property rights for this product 4

EN-25

FX-J80U_3rd_EN.indd 25FX-J80U_3rd_EN.indd 25 2021/09/29 11:41:562021/09/29 11:41:56

ESPAÑOL

CONTENIDO

INSTRUCCIONES DE SEGURIDAD IMPORTANTES ..... ES-2

NOMBRE DE LAS PARTES ............................................. ES-5

INSTALACIÓN DEL FILTRO ............................................ ES-7

OPERACIÓN ..................................................................... ES-8

CUIDADO Y MANTENIMIENTO ....................................... ES-11

EN ESTA SITUACIÓN ....................................................... ES-14

ESPECIFICACIONES ....................................................... ES-15

OTROS AJUSTES ............................................................ ES-16

Gracias por comprar este Purificador de aire SHARP.

Lea este manual detenidamente antes de utilizar el producto.

Este manual debe guardarse en un lugar seguro para consultarlo en el futuro.

FX-J80U_3rd_SP.indd 1FX-J80U_3rd_SP.indd 1 2021/09/29 11:48:002021/09/29 11:48:00

ESPAÑOL

Declaración de conformidad

PURIFICADOR DE AIRE SHARP

FX-J80U

Este dispositivo cumple con la Parte 18

del reglamento FCC.

Parte responsable:

SHARP ELECTRONICS CORPORATION

100 Paragon Drive, Montvale, NJ 07645,

U.S.A

Este adaptador Wi-Fi cumple con la Parte 15 del

reglamento FCC. Su funcionamiento está sujeto a

las dos condiciones siguientes: (1) Este dispositivo

puede no causar interferencias perjudiciales y

(2) debe aceptar cualquier interferencia recibida,

incluyendo interferencias que puedan causar un

funcionamiento no deseado.

• Contiene FCC: RX3-B01

ES-1

El puricador de aire absorbe el aire de la

entrada de aire y éste pasa a través del

pre-ltro, un Filtro desodorizante de carbón

activo y un Filtro True HEPA en la parte

interna de la unidad, y luego lo descargar

a través del oricio de descarga de aire. El

Filtro True HEPA puede eliminar el 99,97%

de las partículas de polvo de tamaño tan

pequeño como 0,3 micrones que atraviesan

el ltro y también ayuda a absorber los

olores. El ltro desodorizante de carbón

activo absorbe gradualmente los olores a

medida que atraviesan el ltro.

Algunos olores absorbidos por los ltros pueden descomponerse con el paso del tiempo,

causando olores adicionales. Dependiendo del ambiente en el que se use el producto,

especialmente cuando es usado en ambientes considerablemente más severo que el uso

doméstico normal, estos olores pueden volverse más perceptibles antes de lo esperado. Si los

olores persisten, debe reemplazar los ltros. (Página 7,12)

•El purificador de aire está diseñado para eliminar el polvo en suspensión en el aire y los olores.

El purificador de aire no está diseñado para eliminar gases nocivos como el monóxido de carbono contenido en el

humo de un cigarrillo.

Si aún continúa la fuente de los olores, el purificador de aire no los podrá eliminar completamente.

Lea antes de operar su nuevo Purificador de aire

NOTA

Filtro True HEPA

Filtro

desodorizante de

carbón activo

Panel

posterior

(Pre-ltro)

FX-J80U_3rd_SP.indd 1FX-J80U_3rd_SP.indd 1 2021/09/29 11:48:012021/09/29 11:48:01

ES-2

INSTRUCCIONES DE SEGURIDAD IMPORTANTES 1

Lea y guarde estas instrucciones

antes de utilizar este producto.

Al usar artefactos eléctricos, se deben

cumplir precauciones de seguridad

básicas, para reducir el riesgo de choques

eléctricos, incendios o lesiones a personas

incluyendo las siguientes:

ADVERTENCIA

1. Lea todas las instrucciones antes de

usar el producto.

2. Utilice este producto solo para uso

doméstico previsto como se describe

en este manual. Cualquier otro uso no

recomendado por el fabricante puede

causar choques eléctricos, incendios o

lesiones a personas.

3. Este dispositivo no está hecho para

ser utilizado por personas (incluyendo

a niños) con capacidades físicas,

sensoriales o mentales disminuidas,

o con falta de experiencia y

conocimiento, a no ser que hayan sido

supervisados o instruidos con respecto

al uso del dispositivo por una persona

responsable de su seguridad.

Los niños deben supervisarse para

asegurar que no jueguen con el

dispositivo.

4. No opere nunca el producto si el cable

de alimentación o el enchufe están

dañados o si el producto funciona mal

o está dañado.

5. Si el cable de alimentación está

dañado, debe ser reemplazado por

el fabricante, su agente de servicio,

centro de servicio autorizado Sharp

o una persona calificada para evitar

peligros.

Comuníquese con el Centro de servicio

autorizado más cercano para cualquier

problema, ajuste o reparación.

6. No repare o desmonte el producto

usted.

7. Siga las instrucciones a continuación

para el cable de alimentación o el

enchufe. Puede causar cortocircuito,

calor excesivo, choques eléctricos o

incendios.

a. Use únicamente en un tomacorriente

de 120 voltios.

b. No use el producto si el cable de

alimentación o el enchufe están

dañados o si la conexión en el

tomacorriente no es segura.

c. Apague siempre el producto

antes de desenchufar el cable de

alimentación.

d. Desenchufe siempre el producto

antes de moverlo o mantenerlo, abrir

el panel posterior, cambiar los filtros

y siempre que no esté usando el

producto.

e. Asegúrese de tirar del enchufe y no

del cable de alimentación.

f. No toque el enchufe con las

manos húmedas cuando inserte o

desenchufe del tomacorriente de

pared.

g. Elimine periódicamente el polvo del

enchufe.

h. Siempre tenga en cuenta lo

siguiente para no dañar el cable de

alimentación.

• No coloque el cable debajo de

una alfombra No cubra el cable de

alimetación con alfombras, tapetes

u otros cobertores similares.

•No coloque cosas pesadas encima

del cable de alimentación o lo

pellizque.

• No conduzca el cable de

alimentación debajo de muebles u

otros artefactos.

• Coloque el cable de manera

que quede alejado de zonas

transitadas o donde pueda

ocasionar tropiezos.

8. El producto tiene un enchufe polarizado

(una espiga es más ancha que la

otra). Para reducir el riesgo de choque

eléctrico, este enchufe solo encaja

en una toma polarizada en una sola

dirección. Si el enchufe no encaja en el

tomacorriente, invierta el sentido.

Si aún así no cabe, póngase en

contacto con un electricista calificado

o proveedor de servicio. No intente

superar esta función de seguridad.

9. No utilice este producto cerca de

artefactos de gas, hogueras, velas

encendidas, incienso o chispas de

cigarrillos encendidos.

10. No opera el producto en una habitación

con gases inflamables, como residuos

de aceite o vapores químicos.

FX-J80U_3rd_SP.indd 2FX-J80U_3rd_SP.indd 2 2021/09/29 11:48:012021/09/29 11:48:01

ES-3

ESPAÑOL

11. No exponga el producto a la lluvia, o

lo utilice cerca del agua, en un baño,

lavandería u otra ubicación mojada.

12. No introduzca los dedos ni objetos

extraños en la entrada o la salida de

aire.

13. No mire en las descargas de aire.

NOTA - Interferencia de radio o televisión

Si el producto causa alguna interferencia

con la recepción de la radio o televisión,

intente corregir la interferencia por medio

de una o más de las medidas siguientes:

1. Reoriente o reubique la antena de

recepción.

2. Aumente la separación entre el

producto y el receptor de radio/TV.

3. Conecte el producto en un

tomacorriente de un circuito diferente

al circuito en el cual se conecta el

receptor.

4. Consulte al distribuidor o a un técnico

de radio/TV con experiencia si requiere

ayuda.

PRECAUCIONES

RELACIONADAS CON LA

INSTALACIÓN

1. Coloque el producto sobre una

superficie estable con circulación de

aire suficiente.

Al colocar la unidad en una zona muy

alfombrada, puede hacer que la unidad

vibre ligeramente.

2. Evite lugares donde el sensor esté

expuesto a la corriente directa de la

brisa o el proyecto. En caso contrario

el producto podría no funcionar

correctamente.

3. Evite usar la unidad en lugares donde

las cortinas, etc. puedan entrar en

contacto con la entrada y/o salidas de

aire.

4. Evite lugares expuestos a la luz directa

del sol. Puede causar que cambie la

forma o el color del producto.

5. Evite sitios en donde la unidad esté

expuesta a una condensación, debido

a cambios de temperatura rápidos.

Utilice la unidad en condiciones

apropiadas que estén entre 32 -95 ºF (0

– 35 ºC).

6. Evite los lugares donde se genere

grasa o humo aceitoso. (como por

ejemplo en la cocina, etc.). Esto

puede causar grietas en la superficie

de la unidad principal y fallas en el

funcionamiento del sensor.

7. La capacidad del producto de recoger

polvo es efectiva incluso si el producto

está tan cerca de 1,2 pulgadas (3 cm)

de la pared, pero las paredes alrededor

o el suelo se puede poner sucia.

Por favor, coloque el producto a una

distancia de la pared.

La pared directamente detrás de las

descargas de aire y el suelo o tapete

sobre el que el producto está colocado

se pone sucio con el paso del tiempo.

Al usar el producto durante un periodo

de tiempo ampliado en el mismo lugar,

limpie periódicamente las paredes, el

suelo o el tapete.

PRECAUCIONES

RELACIONADAS CON EL

FILTRO

1. Siga las instrucciones en este

manual para la instalación del

filtro y el mantenimiento. (Página

7,11,12)

2. Retire la bolsa plástica del filtros

antes de colocar el filtro en la unidad

principal.

3. No opere el producto sin los filtros

instalados correctamente.

4. No lave ni reutilice el filtro True HEPA y

el filtro desodorizante de carbón activo.

Lavarlo no mejorará el rendimiento del

filtro y también puede provocar choque

eléctrico o mal funcionamiento.

5. No opere el producto en una habitación

donde haya insecticidas en aerosol.

Puede causar que el olor de insecticida

permanezca en el producto y se emita

desde las descargas de aire.

PRECAUCIONES

RELACIONADAS CON LA

OPERACIÓN

1. No bloquee la entrada y/o salida de

aire.

INSTRUCCIONES DE SEGURIDAD IMPORTANTES 2

FX-J80U_3rd_SP.indd 3FX-J80U_3rd_SP.indd 3 2021/09/29 11:48:012021/09/29 11:48:01

ES-4

2. Siempre opere el producto en posición

vertical.

3. Siempre sujete la agarradera de el

producto al moverla.

4. Eleve siempre el producto cuando lo

mueva en suelo dañado fácilmente,

superficie irregular y alfombras.

PRECAUCIONES

RELACIONADAS CON EL

MANTENIMIENTO

1. Siga las instrucciones para

mantenimiento en este manual.

(Página 11 - 13)

2. Sólo limpie la parte externa con un

paño suave.

3. No utilice líquidos volátiles y/o

detergentes.

Puede causar daños o grietas en

la superficie de la unidad principal

si se usan limpiadores fuertes de

tipo corrosivo, benceno, diluyente

de pintura, polvo de pulido o grasa.

Además, puede dañar los sensores

como resultado si el producto tiene

sensores.

4. No fregar el panel posterior (pre-filtro)

fuerte durante su mantenimiento.

5. Cuando reemplace filtros o cualquier

accesorio, utiliza las partes

especificadas en este manual.

INSTRUCCIONES DE SEGURIDAD IMPORTANTES 3

FX-J80U_3rd_SP.indd 4FX-J80U_3rd_SP.indd 4 2021/09/29 11:48:012021/09/29 11:48:01

ES-5

ESPAÑOL

NOMBRE DE LAS PARTES 1

(PARTE FRONTAL)

(PARTE POSTERIOR)

1514

1 2

1Panel de operación

2Salida de aire (Frontal / Posterior)

3Monitor de calidad de aire

4Pantalla frontal

5Unidad principal

6Manija

(2 ubicaciones: izquierda y derecha)

7Rejilla frontal

8Panel posterior (Pre-filtro)

9Toma de aire

10 Filtro desodorizante de carbón

activo

11 Filtro True HEPA

Filtro de sensor

Sensor (Interno) Olor / Sensible al

polvo / Temperatura / Humedad

13 Unidad*

(Unidad generadora de

iones Plasmacluster)

14 Unidad* Soporte

15 Unidad* Cubierta

16 Unidad* Cepillo de limpieza

17 Cable de alimetación, Enchufe

* La unidad se refiere a la unidad

generadora de iones Plasmacluster.

FX-J80U_3rd_SP.indd 5FX-J80U_3rd_SP.indd 5 2021/09/29 11:48:022021/09/29 11:48:02

ES-6

PANTALLA FRONTAL

PANEL DE OPERACIONES Pulse cualquier botón con “ ” para iniciar.

12345678

21 22201918171615141312

1Botón ENCENDIDO / APAGADO

2Botón Wi-Fi ()

3Botón AUTO, Luz de indicador - blanco

Botón LIMPIEZA RÁPIDA PLASMACLUSTER,

Luz de indicador - blanco

5Botón ión Plasmacluster SPOT,

Luz de indicador - blanco

Botón velocidad del ventilador, Luz de

indicador - blanco

(Pulsar 3 seg.*) Botón Plasmacluster

ENCENDIDO / APAGADO

7Botón TEMPORIZADOR

(Pulsar 3 seg.*)

Botón REESTABLECER FILTRO

Botón PANTALLA

(Pulsar 3 seg.*)

Botón BLOQUEO PARA NIÑOS

9Luz indicadora de bloqueo para niños

- blanco

10 Sensor de luz

Monitor de calidad de aire

Indica la pureza del aire de la habitación en 5 niveles

concambios de color.

12 Indicador Wi-Fi ()

13 Indicador SHARP CLOUD ( )

Monitor PM2.5

Indica que el sensor de polvo sensible detecta polvo

microscópico.

APAGAR Naranja Rojo

Limpio Impuro

Azul

Limpio

Rojo

Impuro

Monitor de polvo

Monitor de olor

Monitorea continuamente el polvo u olor en el aire y cambia

de color dependiendo de la pureza.

APAGAR Naranja Rojo

Limpio Impuro

17 Indicador de sustitución de unidad

18 Indicador de mantenimiento de filtro

19 Indicador de temporizador ENCENDIDO

20 Indicador de temporizador APAGADO

21 Indicador de ión Plasmacluster

PANTALLA

Los números visualizados son valores

aproximados.

•Monitor PM2.5

Se visualiza de PM2.5 10μg/m3 a 499μg/m3.

•Monitor de potencia

Indica la potencia según la operación en curso.

•Monitor de humedad

Se muestra la humedad entre el 20% y el 90%.

•Monitor de temperatura

Se muestra Temperatura 32oF a 122oF.

• Monitor de temporizador

Indica el tiempo de ajuste el tiempo restante

del temporizador ENCENDIDO / APAGADO.

500μg/m3

o más

9μg/m3

o menos

20%

o menos

90%

o más

123oF

o más

31oF

o menos

Para obtener detalles sobre objetos marcados con ( ), consulte la Guía de conexión Wi-Fi.

* Mantenga presionado 3 segundos o más.

NOMBRE DE LAS PARTES 2

FX-J80U_3rd_SP.indd 6FX-J80U_3rd_SP.indd 6 2021/09/29 11:48:102021/09/29 11:48:10

ES-7

ESPAÑOL

4. Instale el panel posterior.

5. Registre la fecha en la que inició

o reemplazó los filtros en la

contraportada de este manual.

Clic

Active Carbon Deodorizing Filter

Filtro desodorizante de carbón activo

Model

Modelo

Starting date of use

Fecha de comienzo de uso

. . . .

True HEPA Filter

Filtro true HEPA

Model

Modelo

Starting date of use

Fecha de comienzo de uso

. . . .

FZ-J80HFU

FZ-J80DFU

1. Retire el panel posterior.

2. Retire los filtros de la bolsa de

plástico.

3. Instale los filtros en el orden

correcto como se muestra.

Panel posterior

Filtro True HEPA

Filtro desodorizante

de carbón activo

•Para mantener la calidad de los filtros, estos están instalados en la unidad principal y

empacados en bolsas plásticas.

•Asegúrese de detener la operación y desenchufar el producto antes de instalación o

reemplazo el filtro.

• No opere el producto sin el filtros.

INSTALACIÓN DEL FILTRO

NOTA

Filtro True HEPA

Filtro desodorizante

de carbón activo

FX-J80U_3rd_SP.indd 7FX-J80U_3rd_SP.indd 7 2021/09/29 11:48:142021/09/29 11:48:14

ES-8

• El producto emite iones Plasmacluster de alta

densidad solo en la dirección hacia adelante.

• El producto produce aire más fuerte durante 8

horas. Cuando la operación finaliza, el producto

volverá a su modo de operación anterior.

•El ión Plasmacluster no puede ponerse en

“APAGADO”.

MODO SPOT IÓN

PLASMACLUSTER

INICIAR/DETENER

BOTÓN VELOCIDAD

DEL VENTILADOR

SLEEP:

El producto funcionará silenciosamente y la

velocidad del ventilador cambiará automáticamente

según la cantidad de impurezas en el aire de la

habitación y el brillo.

La pantalla frontal y el monitor de calidad del aire

cambian automáticamente su atenuación o se

APAGA según el brillo de la habitación.

La habitación es luminosa: la luz se atenúa

La habitación está oscura: la luz está APAGADA

POLEN:

El sensor de polvo aumenta automáticamente y

detecta rápidamente las impurezas, como el polvo

y el polen, y limpia el aire con potencia.

INICIAR DETENER

OPERACIÓN 1

♪

MODO AUTOMÁTICO

La velocidad de ventilador es controlada

automáticamente dependiendo de 3 detecciones.

(Polvo / Olor / Luz)

• A no ser que se haya desconectado el cable

de alimentación, la operación se reanudará

automáticamente en el modo anterior en el que

estaba funcionando.

Ejemplo: si se pierde la energía durante la operación,

se reanudará al modo de operación y configuración

anteriores una vez que se restaura la energía.

♪

♪♪

POLEN

SLEEP

BAJO

MED

MAX

♪

El producto libera iones Plasmacluster a un flujo de

aire máximo durante 10 minutos. Después de eso,

el purificador de aire funciona durante 50 minutos a

alta velocidad del ventilador.

NOTA

•Cuando la operación finaliza después de

60 minutos, el producto volverá al modo de

operación anterior. Es capaz de cambiar a otros

modos durante esta operación.

•El ión Plasmacluster no puede ponerse en

“APAGADO”.

MODO LIMPIEZA

RÁPIDA PLASMACLUSTER

♪

OPERACIÓN 1

NOTA

• Cuando el control de luz está configurado en

“Automático”, la pantalla frontal, el monitor de calidad

del aire se encenderá automáticamente o se atenuará

según el brillo de la habitación. (Página 10)

NOTA

♪

FX-J80U_3rd_SP.indd 8FX-J80U_3rd_SP.indd 8 2021/09/29 11:48:232021/09/29 11:48:23

ES-9

ESPAÑOL

OPERACIÓN 2

♪

♪♪

Humedad

Potencia

Nivel PM2.5

Temperatura

BLOQUEO INFANTIL

PLASMACLUSTER

ENCENDIDO/APAGADO

El panel de operación estará bloqueado.

Cuando la función Plasmacluster está en

ENCENDIDO, la luz indicadora de iones

Plasmacluster está encendida. (Página 6)

(con el producto ENCENDIDO)

Pulsar durante 3 seg.

♪

Pulsar durante 3 seg.

♪

Pulsar durante 3 seg.

♪♪

Pulsar durante 3 seg.

♪♪

ENCENDIDO

CANCELACIÓN

APAGADO

SELECCIONAR

PANTALLA

Configure el TEMPORIZADOR DE ENCENDIDO

cuando desee programar el encendido del

purificador de aire después de un determinado

número de horas.

•Si ya configuró el temporizador con la aplicación,

no puede configurar el temporizador con el

producto.

•Si ya configuró el temporizador con la aplicación,

no puede configurar el temporizador con el

producto.

Configure el TEMPORIZADOR DE APAGADO

cuando desee programar el purificador de aire para

que se apague después de un determinado número

de horas.

TEMPORIZADOR DE

ENCENDIDO

TEMPORIZADOR DE

APAGADO

(con el producto APAGADO)

(con el producto ENCENDIDO)

Pantalla frontal

……

♪ ♪ ♪ ♪ ♪♪

1 hora 2 horas 3 horas 12 horas

Cancelación

……

♪ ♪ ♪ ♪ ♪♪

1 hora 2 horas 3 horas 12 horas

Cancelación

NOTA

•Cada vez que pulse el botón TEMPORIZADOR,

cambiará la hora de inicio automático en la

siguiente secuencia:

•Cada vez que pulse el botón TEMPORIZADOR,

en la siguiente secuencia cambiará el tiempo de

apagado automático:

• Es posible desactivar el Wi-Fi mientras está en el

modo de bloqueo para niños.

NOTA

FX-J80U_3rd_SP.indd 9FX-J80U_3rd_SP.indd 9 2021/09/29 11:48:322021/09/29 11:48:32

ES-10

1. Poner el producto en

APAGADO.

2. Seleccionar

Establecer

Pulsar durante 3 seg.

♪

CÓMO CAMBIAR VARIOS AJUSTES

Puede cambiar las funciones listadas en las tabla a continuación.

Función ( ) Ajuste ( )

Control de luces

Puede seleccionar el brillo de la pantalla frontal y

el monitor de calidad del aire.

Apagar *

Atenuar

Automático (por defecto)

La luz se conmuta automáticamente según el

brillo de la habitación.

Brillo de la

habitación

Pantalla frontal y monitor de calidad de aire

MODO TOTAL

(Excepto en SUSPENSIÓN)

MODO SUSPENSIÓN

Brillo ENCENDIDO Atenuar

Oscuro Atenuar Apagar

Reanudación automática

Este modelo tiene la función de Reanudación automática,

la operación se reanuda en el modo y configuración

anteriores una vez que se restaura la energía.

CANCELACIÓN

ENCENDIDO (por defecto)

Ajustar la sensibilidad del sensor (F3-F5)

Para obtener información, consulte la Página 14.

Sensor de luz Baja

Sensor de polvo sensible Estándar(por defecto)

Sensor de olor Alto

Cuando se establece en “Apagar”, la luz “Atenuar” se ilumina durante 8 segundos después de que comience la operación y luego se apaga.

3. Seleccionar “Número de función”.

IR ATRÁS IR ADELANTE

Establecer ♪

4. Seleccionar “Número de ajuste”.

IR ATRÁS IR ADELANTE

Establecer ♪～

5. Finalizar el ajuste.

♪♪

････

♪♪

Apagar

♪～

OPERACIÓN 3

Para obtener la información sobre

seleccionar A, consulte la Página

17 - 19.

Ver las funciones en la

tabla a continuación.

Consulte los ajustes en la

tabla a continuación.

♪

♪*

Ajuste de

producto

Ajuste

Wi-Fi

• Puede seleccionar F o A.

FX-J80U_3rd_SP.indd 10FX-J80U_3rd_SP.indd 10 2021/09/29 11:48:542021/09/29 11:48:54

ES-11

ESPAÑOL

Limpie con un paño seco y suave

Elimine el polvo suavemente con una

herramienta de limpieza tal como una

aspiradora.

UNIDAD PRINCIPAL /

PANEL POSTERIOR

Panel

posterior

(Pre-filtro)

•Para mantener el rendimiento óptimo de este puri cador de aire, limpie el producto

incluyendo el puri cador periódicamente.

• Antes de cualquier mantenimiento o sustituir accesorios, asegúrese de dejar de operar o

desconectar el producto.

INDICADOR DE MANTENIMIENTO DE FILTRO

El indicador de mantenimiento del filtro se volverá rojo* cuando sea el momento de dar mantenimiento el panel

posterior (prefiltro) .

*Este indicador se volverá rojo después de aproximadamente 720 horas de funcionamiento. (30 años × 24 horas

= 720 horas)

Después del mantenimiento, conecte el enchufe al tomacorriente de pared y pulse el botón ENCENDIDO /

APAGADO, luego pulse el botón TEMPORIZADOR durante 3 segundos.

MANTENIMIENTO

REESTABLECER

Pulsar durante 3 seg.

Apagar

Cómo limpiar fuerte para retirar suciedad

Panel posterior

1. Añada una pequeña cantidad de

detergente neutro al agua y remojar

durante unos 10 minutos.

No aplique una presión excesiva al cepillar el

panel posterior.

2. Aclare el detergente neutro con agua limpia.

3. Seque completamente el filtro en una

zona bien ventilada.

Filtro de sensor

1. Retire el panel posterior.

2. Retire el filtro del sensor.

3. Si el filtro del sensor está muy sucio,

lávelo con agua y séquelo bien.

Filtro de

sensor

NOTA

CUIDADO Y MANTENIMIENTO 1

♪

Cuando la luz del indicador del filtro de

mantenimiento se enciende.

FX-J80U_3rd_SP.indd 11FX-J80U_3rd_SP.indd 11 2021/09/29 11:49:002021/09/29 11:49:00

ES-12

FILTRO TRUE HEPA /

FILTRO DESODORIZANTE DE CARBÓN ACTIVO

CUIDADO Y MANTENIMIENTO 2

Eliminar el polvo de los filtros.

Algunos olores absorbidos por los filtros pueden descomponerse con el paso del tiempo, causando olores adicionales.

Dependiendo del ambiente en el que se use el producto, especialmente cuando es usado en ambientes considerablemente

más severo que el uso doméstico normal, estos olores pueden volverse más perceptibles antes de lo esperado.

En esos casos sustituya el filtro o si no se puede eliminar el polvo después del mantenimiento.

Eliminación de ltros

Deseche los filtros reemplazados en conformidad con las leyes y regulaciones de desecho locales.

Nombre del filtro Aproximadamente ciclo de

mantenimiento Máxima vida del

uso Modelo para reemplazar

filtro

Filtro True HEPA Cada vez que se acumule el polvo,

cuando el mal olor se libera de la salida

de aire, o una vez al mes. 2 años*1, 2

FZ-J80HFU

Filtro desodorizante

de carbón activo FZ-J80DFU

*¹ Según la norma JEM 1467 de la asociaciòn de Fabricación eléctrica de Japón, la vida de servicio màxima se basa en la

condición equivalente del humo producido por 5 cigarrillos al día. Bajo dicha condiciòn, la capacidad de recolecciòn de

polvo se reducen hasta la mitad a comparaciòn con el filtro nuevo. Se recomienda reemplazar el filtro con mayor frecuencia

encondiciones de uso màs severas.

*² La aplicación designada notifica cuándo se deben reemplazar los filtros o la unidad generadora de iones Plasmacluster de

acuerdo con el uso.

NOTA

Consulte la página 7 para ver las

pautas sobre cómo instalar el ltro al

reemplazar.

• Consulte a su distribuidor para comprar el ltro de

reemplazo.

• Use solo el ltro diseñado para este producto.

FZ-J80HFU: 1 unidad FZ-J80DFU: 1 unidad

Registre la fecha en la que reemplazó los ltros

en la contraportada de este manual.

REEMPLAZO Y CICLO DE MANTENIMIENTO

MANTENIMIENTO

REEMPLAZO

No lavar los ltros. No exponer a la luz del sol. (De

lo contrario, estos ltros pueden perder su ecacia).

Etiqueta

FILTRO TRUE HEPA

Mantener solo la

superficie etiquetada.

No limpie la superficie

opuesta.

El filtro es frágil, por lo

tanto tenga cuidado de no

aplicar demasiado presión.

FILTRO DESODORIZANTE DE CARBÓN ACTIVO

Se pueden mantener ambas

superfícies.

El filtro es frágil, por lo tanto

tenga cuidado de no aplicar

demasiado presión.

Escanee el código

QR para obtener la

información de producto

y accesorios.

FX-J80U_3rd_SP.indd 12FX-J80U_3rd_SP.indd 12 2021/09/29 11:49:042021/09/29 11:49:04

ES-13

ESPAÑOL

CUIDADO Y MANTENIMIENTO 3

Cuando el tiempo total de operación supera las 17.500 horas, el indicador de reemplazo de la unidad parpadeará

para indicar que la unidad generadora de iones Plasmacluster necesita reemplazo.

Tiempo de operación

17.500 horas

Parpadea lentamente

Reemplace la unidad generadora de iones Plasmacluster

19.000 horas

Parpadea rápidamente

Detenga la emisión de los iones Plasmacluster.

*El tiempo de reemplazo no está relacionado con el modo de operación seleccionado.

Consulte a su distribuidor cuando compre una unidad generadora de iones Plasmacluster de repuesto.

Modelo: IZ-C90MU

Eliminación de la unidad generadora de iones Plasmacluster

Deseche la unidad generadora de iones Plasmacluster usada de acuerdo con las leyes y regulaciones locales.

①

②

①

1. Retire la cubierta de la

unidad, y extraiga el

soporte de la unidad.

2. Retire polvos de la sección

de electrodo.

3. Introduzca el soporte de

la unidad en la unidad

principal e instale la

cubierta de la unidad.

• No limpie con ninguna otra cosa que no sea el cepillo de limpieza de la unidad. Hacerlo podría provocar fallos en la unidad.

• Un electrodo doblado podría cortarse y soltarse durante el proceso de limpieza, pero eso no cambiará el rendimiento.

•No toque el electrodo directamente.Hacerlo podría provocar dolor / picazón.

•No transforme la sección del electrodo. Hacerlo puede dañarlo.

•No toque los terminales de conexión. Hacerlo puede dañarlos.

UNIDAD GENERADORA DE IÓN PLASMACLUSTER

(sección de electrodo)

Cepillo de limpieza de unidad

Electrodo Alrededor de la base

Antes de la limpieza Después

de la

limpieza

MANTENIMIENTO

INDICADOR DE REEMPLAZO DE UNIDAD

REEMPLAZO

Retire el gancho del soporte de la unidad

(

), y retire la unidad generadora de

iones Plasmacluster (

NOTA

FX-J80U_3rd_SP.indd 13FX-J80U_3rd_SP.indd 13 2021/09/29 11:49:092021/09/29 11:49:09

ES-14

EN ESTA SITUACIÓN

El olor y el humo persisten.

• Compruebe los filtros. Si parecen estar

extremadamente sucios, límpielos o

reemplácelos.

El aire descargado del producto

tiene un olor.

•Compruebe si los filtros están extremadamente

sucios.

Limpie o reemplace los filtros.

El producto no funciona cuando

hay humo de cigarrillo en el aire.

• Asegúrese de que el producto esté instalado en

un lugar en el que los sensores puedan detectar

humo de cigarrillo.

• Compruebe si las aberturas del sensor de polvo

sensible están bloqueadas u obstruidas. Si están

bloqueados u obstruidos, limpie el filtro del sensor

o el panel posterior.

Olor de un filtro nuevo.

• Inmediatamente después de retirar la bolsa de

plástico, puede ocurrir un leve olor.

Este olor no es nocivo para el rendimiento del

filtro o la exposición humana.

El producto emite un sonido de

clic o tictac.

• El producto puede emitir sonidos de clic o tictac

cuando genera iones.

El monitor de calidad del aire es

azul incluso cuando el aire no está

limpio.

• El aire puede haber estado sucio cuando se

enchufó el producto. Desenchufe el producto,

espere un minuto y luego vuelva a enchufarlo.

El monitor de calidad del aire es

rojo incluso cuando el aire está

limpio.

• Sucias u obstruidas las aberturas del sensor de

polvo sensible interfieren con el funcionamiento

del sensor. Limpie suavemente el filtro del sensor

o el panel posterior.

El monitor de calidad del aire

cambia de color frecuentemente.

• El monitor de calidad del aire cambia

automáticamente de color cuando el sensor

de polvo sensible y el sensor de olor detectan

impurezas. Si le preocupa el cambio, puede

cambiar la sensibilidad del sensor. (Página 10)

La luz indicadora de

mantenimiento del filtro está

encendida.

• Siempre después de realizar el mantenimiento

de los filtros, conecte el cable de alimentación

a un tomacorriente y presione el botón de

ENCENDIDO / APAGADO, luego presione el

botón de REINICIO DEL FILTRO. (Página 11)

La pantalla frontal se apaga.

•Cuando el control de la luz esté en “Apagar”, la

luz siempre está apagada. Si no desea que la luz

esté apagada, establezca el control de luz en el

ajuste “Automático” o “Atenuar”.

(Página 10)

La pantalla del producto

no coincide con el informe

meteorológico u otro higrómetro o

termómetro en la habitación.

•Tanto exterior como interior, así como el entorno

del hogar (el volumen de tráfico cercano, la

cantidad de historias en el hogar, etc.) pueden

causar una lectura diferente a esos datos.

• Hay una diferencia en el nivel dentro de la misma

habitación.

¿Cuándo se debe cambiar la

sensibilidad del sensor?

Cambie la sensibilidad del sensor de la siguiente

manera según cada caso.

Sensor de luz

•Cambie a “Baja” cuando la pantalla frontal aún

se ilumine brillantemente incluso si se oscurece

en la habitación.

•Cambie a “Alta” cuando la pantalla frontal se

ilumine oscura incluso si hay mucha luz en la

habitación.

Sensor de polvo sensible

•Cambie a “Baja” cuando PM2.5, el monitor de

polvo o calidad del aire se muestre en rojo con

frecuencia.

•Cambie a “Alta” cuando PM2.5 o el monitor de

polvo no se encienda o el monitor de calidad

del aire permanece en azul incluso si hay polvo

en la habitación.

Sensor de olor

•Cambie a “Bajo” cuando el monitor de olor se

muestre en rojo con frecuencia.

•Cambie a “Alta” cuando el monitor de olor no

se encienda, incluso si hay algo de olor en la

habitación.

Antes de llamar a mantenimiento, por favor revise la lista a continuación, ya que el problema

puede no ser un mal funcionamiento de la unidad.

FX-J80U_3rd_SP.indd 14FX-J80U_3rd_SP.indd 14 2021/09/29 11:49:092021/09/29 11:49:09

ES-15

ESPAÑOL

PANTALLA DE ERROR

Parpadea rápido

•La comunicación entre el servidor

SHARP y el purificador de aire no

está disponible.

Consulte la Guía de conexión Wi-Fi

para obtener más información.

• ¿Se ha introducido correctamente

la unidad generadora de iones

Plasmacluster?

⇒Saque la unidad generadora

de iones Plasmacluster e insértela

hasta el final de nuevo, y luego

vuelva a ponerla en funcionamiento.

•La concentración de iones

Plasmacluster está descendiendo.

⇒Mantenga la sección del

electrodo de la unidad generadora

del ión Plasmacluster. (Página 13)

• Desenchufe el producto, espere un

minuto y luego vuelva a enchufarlo.

Modelo FX-J80U

Fuente de alimentación 120 V / 60 Hz

Manejo de la velocidad

del ventilador

Ajuste de velocidad del ventilador MAX MED SLEEP

Potencia nominal (Vatios) 70 27 3,2

Velocidad del ventilador (CFM) 321 170 35

Nivel de ruido (dBA)*1 49 45 15

Energía de reserva (Vatios) 0,9 (Cuando el adaptador Wi-Fi está encendido.)

0,7 (Cuando el adaptador Wi-Fi está apagado.)

Tamaño recomendado de habitación*2 502 sq. ft. (47 m2)

CADR (Polvo/Humo/Polen) 334 / 324 / 361

Tipo de filtro Recolección de polvo Filtro True HEPA

Desodorización Filtro desodorizante de carbón activo

Longitud del cable 6,6 ft. (2,0 m)

Dimensiones 16,4 in. (W) × 11,5 in. (D) × 28,7 in. (H)

(416 mm (W) × 291 mm (D) × 728 mm (H))

Peso 23,8 lbs. (10,8 kg)

Energía de reserva Este producto consume una cantidad mínima de energía mientras está en

modo de espera.

Para ahorrar energía eléctrica, desenchufe el cable de energía cuando no

esté usando el producto.

*1 El nivel de ruido se mide basado en norma JEM 1467 de la asociaciòn de Fabricación eléctrica

de Japón.

*2 Tamaño de una habitación adecuado para el funcionamiento del producto a la velocidad

máxima del ventilador.

ESPECIFICACIONES

FX-J80U_3rd_SP.indd 15FX-J80U_3rd_SP.indd 15 2021/09/29 11:49:142021/09/29 11:49:14

ES-16

OTROS AJUSTES 1

SEGURIDAD / PRECAUCIONES

ADVERTENCIA

En caso de una operación remota desde el exterior,

es posible que no pueda vericar la condición actual

del puricador de aire o el área a su alrededor

y la situación relacionada con la posibilidad de

que alguien se quede allí, por lo tanto, conrme

adecuadamente la seguridad antes de usarlo.

• Asegúrese de que el enchufe eléctrico esté

completamente insertado en un tomacorriente y que

no haya polvo en el enchufe o en el oricio de la toma.

(Puede causar calor, combustión, fuego, etc., debido a

un mal contacto o fallo de contacto)

• Asegúrese por adelantado de que, aunque haya

algunos cambios de viento, no se producirá ningún

impacto negativo en el medio ambiente dentro de la

habitación. (como ... si hay algo volando fácilmente en

el viento) Debido a que el viento puede hacer que algo

se caiga, dando como resultado incendios, heridas,

desguración de enseres domésticos.

PRECAUCIONES DE USO

•Se necesita estar de acuerdo con los “Términos de

servicio” para usar la aplicación.

•La aplicación se revisará periódicamente debido a la

actualización de la versión.

• Las pantallas e ilustraciones en este libro son para la

explicación, hay algunas diferencias con el producto real.

•En el caso de una mala conexión, es posible que la

aplicación no pueda controlar el puricador de aire. Es

posible que el funcionamiento actual del puricador de

aire no se reeje con precisión en la aplicación.

• Se recomienda bloquear la pantalla del teléfono

inteligente para evitar una operación errónea.

•Aunque la aplicación es gratuita, el cliente tiene que

pagar los gastos de comunicaciones para la descarga

de la aplicación dedicada y el funcionamiento con un

teléfono inteligente o tableta.

PRECAUCIÓN PARA Wi-Fi

Precaución para el uso sobre onda

eléctrica

•En caso de uso en la siguiente ubicación, no se puede

garantizar la operación: Cerca del dispositivo de

comunicaciones inalámbricas Bluetooth® que utiliza

la misma frecuencia (2,4GHz) que este producto o

dispositivo inalámbrico de baja potencia especicado.

También en la ubicación como el campo magnético del

dispositivo, como el horno de microondas, o el lugar con

electricidad estática o donde hay una perturbación de

radio, es posible que no esté disponible temporalmente

debido a una onda eléctrica débil.

•La conexión inalámbrica y el rendimiento no se pueden

garantizar para todos los enrutadores o entornos de

vivienda. En los siguientes lugares, es probable que no

se pueda alcanzar la onda eléctrica o se desconecte:

Dentro del edicio hecho de hormigón, acero reforzado

o metal / cerca de la obstrucción / cerca del dispositivo

de comunicaciones inalámbricas que aplica la misma

frecuencia.

•La conexión Wi-Fi de este producto se corresponde con

el canal 1 - 13. No está disponible para comunicarse

con los enrutadores congurados para otros canales.

Precaución para la información personal

(relacionada con la seguridad)

• Si se utiliza el dispositivo Wi-Fi es posible que sea

interceptada siempre que se utilice una onda eléctrica

independientemente de la conguración del código secreto.

•El Wi-Fi tiene la ventaja de una conexión LAN gratuita

en el área de servicio porque la comunicación entre

este producto y el enrutador aplica una onda eléctrica.

Por otra parte, se podría interceptar la comunicación

o la intrusión injusta porque la onda eléctrica llega a

todas partes en una área determinada a través de las

obstrucciones (p. ej., paredes).

•No conecte el dispositivo o a la red sin que la aplicación

lo autorice.

•La función Wi-Fi para este producto debe inicializarse

en caso de eliminación o que se entregue a una tercera

persona.

•La función Wi-Fi de la unidad debe inicializarse en caso

de que se entregue a una tercera persona para evitar el

acceso ilegal de extraños.

Consulte la Guía de conexión Wi-Fi

para saber cómo conectar y vincular su

dispositivo inteligente con su producto.

Cómo configurar Wi-Fi

ENCENDIDO / APAGADO después

de completar la configuración

inicial

Al apagar el Wi-Fi

Al encender el Wi-Fi de nuevo

Consulte la página 4 - 7 de la Guía de conexión

Wi-Fi del purificador de aire y configure de nuevo

la conexión con el router.

• Si el producto ya está registrado en su teléfono

inteligente, no necesita registrarse de nuevo.

• Wi-Fi ENCENDIDO / APAGADO también se

puede configurar desde

“ :

Adaptador Wi-Fi ENCENDIDO / APAGADO”.

(Página 17)

En este caso, la conexión Wi-Fi con el router se

restaurará automáticamente.

•La reconexión al enrutador inalámbrico puede

tardar unos minutos en completarse, después de

volver a encender el Wi-Fi.

Pulsar durante 3 seg.

♪～

Salir

NOTA

FX-J80U_3rd_SP.indd 16FX-J80U_3rd_SP.indd 16 2021/09/29 11:49:172021/09/29 11:49:17

ES-17

ESPAÑOL

OTROS AJUSTES 2

CÓMO CAMBIAR VARIOS AJUSTES 1

Paso 1. Ponga el producto

en APAGADO.

Paso 2.

Paso 3. Seleccionar .

Paso 4. Seleccionar “Número de función”

IR ATRÁS IR ADELANTE

No Función

Página

Adaptador Wi-Fi ENCENDIDO /

APAGADO 17

Conexión Wi-Fi con enrutador 17

Vincular ajustes con un teléfono

inteligente 18

Inicialización de función Wi-Fi 18

Actualizar 18

Confirmación de dirección MAC 18

Visualizar estado de red Wi-Fi 19

Modo PA (Punto de acceso) 19

Paso 5. Consulte la página 17 - 19

para el detalle de cada función.

Paso 6. Finalizar el ajuste.

♪

Pulse durante 3 seg.

♪

････

Apagar

♪～

Puede cambiar las funciones en la tabla a continuación.

Siga los pasos del 1 al 4 para seleccionar la función.

♪ ♪

1. Seleccionar siguiendo los Pasos 1 - 4.

2. Seleccionar “Establecer número”.

3. Completar ♪

♪

APAGADO:

Parar la función Wi-Fi

ENCENDIDO: Iniciar la

función Wi-Fi

1. Seleccionar siguiendo los Pasos 1 - 4.

2. Después de que se muestre,

presione el botón de configuración

protegida de Wi-Fi (WPS) del router.

Una vez conectado, se visualizará el nivel del

receptor.

Se está produciendo un error de conexión si

se visualiza. Confirme el router e inténtelo de nuevo.

3. Completar ♪

débil fuerte Iluminar

• Cuando está seleccionado, el cuadrado

gira en la pantalla hasta que se completa

la configuración. Cuando se completa la

configuración, se muestra .

Adaptador Wi-Fi

ENCENDIDO / APAGADO

Conexión Wi-Fi con un

router

Establecer ♪

♪Establecer ♪

Parpadeo Parpadeo

FX-J80U_3rd_SP.indd 17FX-J80U_3rd_SP.indd 17 2021/09/29 11:49:392021/09/29 11:49:39

ES-18

OTROS AJUSTES 3

1. Seleccione siguiendo los pasos

1 - 4 en la página 17.

2. Después se visualiza, inicie la

aplicación y registre el purificador

de aire.

Se está produciendo un error de conexión si

se visualiza. Confirme el router e inténtelo

de nuevo.

3. Completar ♪

♪～

Completar

Parpadeo

Configuración

1. Inicie la aplicación y luego pulse

“” en la pantalla “Home” y

seleccione “Update”.

2. Seleccione siguiendo los pasos

1 - 4 en la página 17.

3. Se visualizará .

4. Siga las instrucciones en la pantalla

de la aplicación.

estará parpadeando durante la actualización.

Se producirá un error de conexión si se

visualiza. Confirme el router e inténtelo de nuevo.

El purificador de aire se apagará

automáticamente después de que

se complete la actualización.

Salir

La actualización tardará unos minutos.

1. Seleccione siguiendo los pasos

1 - 4 en la página 17.

2. Después de que se visualice

pulse el botón “AUTOMÁTICO”.

Se produce un error de conexión si se visualiza

. Confirme el router e inténtelo de nuevo.

3. Completar

•Elimine el registro del dispositivo de la aplicación

cuando se inicialice el purificador de aire que ya

está conectado a Wi-Fi.

♪～

Completar

Parpadeo

Inicializando

♪

1. Seleccione siguiendo los pasos

1 - 4 en la página 17.

Pulse el botón Plasmacluster Express

Clean para mostrar la dirección MAC.

3. Completar ♪

Inicialización de la

función Wi-Fi

Vincular ajustes con un

teléfono inteligente Actualizar

Confirmación de la

dirección MAC

CÓMO CAMBIAR VARIOS AJUSTES 2

Por ejemplo :

En caso de que la dirección MAC sea “12 : 34 : 56 : AB : CD : EF”

♪♪♪♪♪♪♪ ♪～

FX-J80U_3rd_SP.indd 18FX-J80U_3rd_SP.indd 18 2021/09/29 11:49:582021/09/29 11:49:58

ESPAÑOL

ES-19

OTROS AJUSTES 4

1. Seleccione siguiendo los pasos

1 - 4 en la página 17.

2. Después de visualizar durante

unos segundos, se visualizará el

estado de red en el adaptador Wi-Fi.

3. Completar ♪

La conexión es estable

El adaptador Wi-Fi está apagado

Encienda el adaptador Wi-Fi.

El router no está registrado

Realice la conexión Wi-Fi con el router.

No se ha realizado la configuración del

enlace con la aplicación .

Realice la configuración de la vinculación

con el teléfono inteligente.

Error de red del adaptador Wi-Fi

Apague el adaptador de Wi-Fi y enciéndalo

de nuevo después de un tiempo.

Error de red entre el purificador de aire y el

router

Confirme el estado de la red del router.

Error de servicio de red

Apague el purificador de aire y confirme el

estado de Internet, luego inténtelo de

nuevo.

1. Seleccione siguiendo los pasos

1 - 4 en la página 17.

2. Realice la conexión Wi-Fi del

purificador de aire y el router según

la pantalla de la aplicación.

Consulte la aplicación o la Guía de

conexión Wi-Fi para conocer más

operaciones.

y parpadea mientras se configura la

conexión entre el producto y el router.

Una vez conectado, se visualizará el nivel del

receptor.

Se produce un error de conexión si se

visualiza. Confirme el router e inténtelo de

nuevo.

débil fuerte Iluminar

Visualizar estado de red

Wi-Fi Modo PA (punto de

acceso)

CÓMO CAMBIAR VARIOS AJUSTES 3

ESPECIFICACIONES

LAN inalámbrica: IEEE802.11b/g/n

Rango de frecuencia: Banda de

frecuencia 2.4GHz

FX-J80U_3rd_SP.indd 19FX-J80U_3rd_SP.indd 19 2021/09/29 11:50:072021/09/29 11:50:07

TINS-B437KKRZ 21K 3

SHARP ELECTRONICS CORPORATION

100 Paragon Drive, Montvale, NJ 07645, U.S.A.

Record the date when you start or replace the filters

Replace the filters when they are no longer removing odor or dust.

Reemplace el filtro cuando éste remueva olor o polvo.

Active Carbon Deodorizing Filter

Filtro desodorizante de carbón activo

Model

Modelo

Starting date of use

Fecha de comienzo de uso

. . . .

True HEPA Filter

Filtro true HEPA

Model

Modelo

Starting date of use

Fecha de comienzo de uso

. . . .

FZ-J80HFU

FZ-J80DFU

Registre la fecha cuando inicie o sustituya los filtros

EPA Est. No. 088806-THA-001

FX-J80U_3rd_EN.indd 26FX-J80U_3rd_EN.indd 26 2021/09/29 11:41:572021/09/29 11:41:57

Sharp FX-J80U El manual del propietario

Marca: Sharp

Modelo: FX-J80U

Categoría: Purificadores de aire

Tipo: El manual del propietario

Descargar PDF

informe

en otros idiomas

English: Sharp FX-J80U Owner's manual

Sharp FX-J80U El manual del propietario

Sharp FX-J80U El manual del propietario

en otros idiomas

Artículos relacionados

Otros documentos