Cooper Lighting ECS-Z-M05-LV Manual de usuario
- Tipo
- Manual de usuario
General Information
Overview
The WaveLinx Pro Insights ceiling sensor is an integral part of the WaveLinx
Pro System and offers Occupant count, Passive Infra-Red (PIR) occupancy
sensing, daylighting, temperature, and humidity capability. This sensor has
Occupant count and Occupancy coverage patterns of up to 600 square feet, it
is low voltage powered and is one of the smartest ceiling mounted sensors for
multi-sensing in the market. The sensor operates on a wireless mesh network
based on IEEE802.15.4 standards.
Plenum rating
The WaveLinx Pro Insights ceiling sensor components intended for installation
above ceiling are plenum rated.
Specifications
Compatible only with Cooper Lighting Solutions Lighting WaveLinx Pro
Wireless Systems.
Power Input power: 120/277VAC
Connections: Hot, Neutral
Indicators LED functionality
• Indication of wireless network connection
• Indication of daylight hold-off
Environmental
Specifications Operating Temperature Range:
-4°F - 131°F (-20°C - 55°C)
Storage Temperature Range:
-40°F - 158°F (-40°C - 70°C)
Relative Humidity: 5% to 95% non-condensing,
for indoor use only
Standards Listings: UL/cUL Listed, FCC, IC
UL244A - Appliance Control /Creepage and Clearance
UL 508/NEMA 410 Industrial Control Equipment
UL 2043 (Plenum installation)
Meets latest ASHRAE Standard 90.1 requirements
Meets latest IECC requirements
Meets latest CEC Title 24 requirements
Wireless
Specifications
Radio 2.4GHz
Standard IEEE 802.15.4
Configuration type Router, End Point
Range 75ft (25m) LOS
2 interior walls of standard construction
Best practice: 100 devices per
Wireless Area Controller
Mounting
Height 8-12ft (2.4 - 3.7m)
www.cooperlighting.com
WaveLinx Pro
Insights Ceiling Sensor
(ECS-Z-M05-LV)
Installation Instructions
WaveLinx Pro
Insights Ceiling Sensor
(ECS-Z-M05-LV)
Instructions d’installation
WaveLinx Pro
Insights Ceiling Sensor
(ECS-Z-M05-LV)
Instrucciones de Instalación
Wiring
The unit is powered by a 24VDC power supply. Please make sure the correct
polarity is used for the power supply connections.
6 WaveLinx Pro Insights Sensors connected to 1 power supply
24 Volt
Power Supply
+
-
Insights Ceiling Sensor Installation
There are various methods that may be used to affix the Wavelinx Insights
Sensor to a ceiling surface.
Tilemount installation
1. Cut 3.8” (95.3mm) diameter hole in ceiling tile.
2. Snap sensor body into ceiling trim.
3. Torsion spring clips secure the Insights Sensor to a recessed ceiling tile.
ceiling tile ceiling tile
2
3
1
Surface Mount / J-Box installation
1. Attach junction box adapter plate to 4” (101.6mm) square junction box.
(screws not included)
2. Align sensor with keyhole pattern.
3. The Wireless Sensor may be installed directly to a ceiling surface via
a 4” (101.6mm) square junction box adapter plate.
4” (101.6mm)
square junction box
adapter plate
Installation Notes
Consult www.cooperlighting.com for the most up-to-date revision of the
Insights Ceiling system design guide and install this product according to the
guidelines described.
The Sensor is to be installed in dry, indoor locations ONLY. Do not install the
Sensor in damp locations. Damp locations are defined as: interior locations
subject to moderate degrees of moisture, such as some basements, some
barns, some cold-storage warehouses, and the like, and partially protected
locations under canopies, marquees, roofed open porches, and the like.
Camera and Sensor Location Notes
The Sensor provides 360° coverage pattern. It is recommended to install the
sensor more than 4ft (1.2m) away from air supply vents.
Canada Sales
5925 McLaughlin Road
Mississauga, Ontario L5R 1B8
P: 905-501-3000
F: 905-501-3172
Cooper Lighting Solutions is a
registered trademark.
All trademarks are property
of their respective owners.
Product availability, specifications,
and compliances are subject to
change without notice.
Cooper Lighting Solutions
1121 Highway 74 South
Peachtree City, GA 30269
www.cooperlighting.com
For service or technical
assistance:
1-800-553-3879
© 2022 Cooper Lighting Solutions
All Rights Reserved
Printed in Mexico
Publication No. IL50372722
August 2022
Single Sensor Setup
1. The imaginary “+” made with the vent holes and LEDs should be
approximately perpendicular with walls when possible.
Imaginary “+” made with the vent holes and LED
room walls
Single camera room
CORRECT orientation
Single camera room
INCORRECT orientation
room walls room walls
✗✔
Multi Sensor Setup
1. The imaginary “+” made with the vent holes and LEDs should be
approximately perpendicular with the walls when possible
2. The lens as a reference point should be facing the same way in all those
included in a multi-sensor setup
3. Best practice for rectangular rooms: The camera side of the sensor
should point at one of the “longer” walls of the room, and as previously
mentioned, the two cameras should both point the same direction. See
image below
longer dimension
Sensor 1 Sensor 2
shorter
dimension
overlap
area
Multi Sensor Camera Orientation
All cameras oriented the SAME direction
All cameras oriented DIFFERENT directions
conference room walls
conference room walls
✗
✔
LED and Button Definitions
• One press and release will reboot the unit
• Press and release 6 times, for 5 seconds each, for a factory reset
Sensor Status LED Indication while in out-of-box mode
There are two LED indicators on this sensor, one positioned above the camera
lens (People count sensor status LED or BLE LED), and one on the other side
below the reset button (Zigbee LED).
On power up
• Zigbee LED blink momentarily in red and once after that it will blink green
on detecting occupancy/motion.
• BLE LED/Occupant Count LED momentarily in Amber and will remain OFF
until sensor is claimed to WAC and registered under license.
Reset button to enable pairing mode
On power up the sensor will not be in pairing mode, it requires two-time power
cycle or IR remote command or press the reset button two times (equivalent
to power cycle) to get the sensor to pairing mode to get join a WAC which is
in pairing/commissioning mode.
Out-of-box functionality
As Insights CS is a ceiling sensor without own light fixture associated to it
there is no user functionality before it is added to the WAC.
Troubleshooting
• There are no user-serviceable parts inside of the Sensor Interface
Module. Please return the device to Cooper Lighting Solutions if service
is required.
• The device is ONLY intended for use with WAC and Trellix releases of SR9
and beyond? (If the device is claimed to a WAC prior to SR9, it will not be
represented correctly and Occupany Counting will not work unless it is
completely reset after the WAC is upgraded to SR9 or later.)
NEED to re-word this.
If still having trouble, call Technical Services at 1-800-553-3879.
AVERTISSEMENT
IMPORTANTE: Lea atentamente antes de instalar la luminaria. Conserve estas instrucciones para tenerlas como referencia
futura.
Riesgo de incendio, descarga eléctrica, cortes u otros riesgos de accidentes: la instalación y el mantenimiento de este
producto deben ser realizados por un electricista calificado. Este producto debe ser instalado de acuerdo con el código de
instalación correspondiente por una persona familiarizada con la construcción y la operación del producto y los peligros
involucrados. Para una protección continua contra el riesgo de electrocución, reemplace todas las cubiertas y protectores
después de que se haya completado el cableado de campo.
Riesgo de incendio y descarga eléctrica: asegúrese de que el suministro eléctrico esté desconectado antes de comenzar
la instalación o intentar realizar cualquier tarea de mantenimiento. Desconecte el suministro eléctrico en el fusible o
disyuntor. Todas las instalaciones deben cumplir con el Código Eléctrico Nacional y todos los códigos estatales y locales.
Riesgo de quemaduras: desconecte el suministro eléctrico y espere que la luminaria se enfríe antes de manipularla o
repararla.
Riesgo de lesiones personales: debido a bordes filosos, manipúlela con cuidado.
El incumplimiento de estas instrucciones puede provocar lesiones graves (incluida la muerte) y daños a la propiedad.
RENUNCIA DE RESPONSABILIDAD: Cooper LIghting Solutions no asume ninguna responsabilidad por daños o pérdidas de ningún tipo
que puedan surgir por la instalación, manipulación o uso inadecuado, descuidado o negligente de este producto.
AVISO: La luminaria puede dañarse y/o ser inestable si no se instala correctamente.
Nota: Las especificaciones y dimensiones están sujetas a cambios sin previo aviso.
ATENCIÓN Departamento de recepción: Observe que la descripción real de la luminaria no carezca de piezas ni presente
daños notorios al momento de su entrega. Presente el reclamo directamente al transportista de carga (LTL). Los reclamos por daños
ocultos deben presentarse dentro de los 15 días posteriores a la entrega. Se debe retener todo el material dañado, completo con el
embalaje original.
AVISO: Diseñado solo para su instalación y uso en interiores
.
Do not mount near gas or electric heaters.
Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel.
The use of accessory equipment is not recommended by Cooper Lighting Solutions as it may cause an unsafe condition.
Do not use this equipment for other than the intended use.
Garantías y Limitación de Responsabilidad
Visite www.cooperlighting.com para conocer nuestros términos y condiciones.
Declaración de la FCC
Nota: El equipo ha sido probado y cumple con los límites para un dispositivo digital de Clase B, de conformidad con la parte 15 de las Normas de la FCC. Estos
límites están diseñados para proporcionar una protección razonable contra las interferencias dañinas en una instalación residencial. Este equipo genera, usos y
puede emitir energía de radiofrecuencia y, si no se instala y utiliza de acuerdo con las instrucciones, puede causar interferencia dañina en las comunicaciones
de radio. Sin embargo, no se puede garantizar que dicha interferencia no ocurra en una instalación determinada. Si este equipo causa interferencia dañina en
la recepción de radio o televisión, lo que puede determinarse apagando y encendiendo el equipo, se recomienda al usuario que intente corregir la interferencia
mediante una o más de las siguientes medidas:
• Reorientar o reubicar la antena receptora.
• Aumentar la separación entre el equipo y el receptor.
• Conectar el equipo a una toma de corriente en un circuito diferente al que está conectado el receptor
• Consultar con el distribuidor o con un técnico de radio/TV experimentado para obtener ayuda.
Declaración de la FCC parte 15 cláusula 15.21
Los cambios o modificaciones no aprobados expresamente por la parte responsable del cumplimiento podrían anular la autoridad del usuario para operar el
equipo.
Declaración de la FCC parte 15.19a
Este dispositivo cumple con la parte 15 de las Reglas de la FCC. El funcionamiento está sujeto a las siguientes dos condiciones: (1) este dispositivo no puede
causar interferencias perjudiciales, y (2) este dispositivo debe aceptar cualquier interferencia recibida, incluidas las interferencias que puedan causar un
funcionamiento no deseado.
Declaración de la FCC parte 2.1093 / RSS102
Este producto cumple con el límite de exposición a RF establecido para un entorno no controlado y es seguro para el funcionamiento previsto como se describe
en este manual.
ISED RSS
Este dispositivo cumple con los RSS exentos de licencia de Industry Canada. El funcionamiento está sujeto a las dos condiciones siguientes: (1) Este dispositivo
no puede causar interferencias; y (2) Este dispositivo debe aceptar cualquier interferencia, incluida la interferencia que pueda causar un funcionamiento no
deseado del dispositivo. CAN ICES-3 (B) / NMB-3 (B).
Las modificaciones no aprobadas expresamente por el fabricante podrían anular la autoridad del usuario para operar el equipo según las normas de la FCC.
ADVERTENCIA
IMPORTANT: Read carefully before installing product. Retain for future reference.
Risk of Fire, Electrical Shock, Cuts or other Casualty Hazards- Installation and maintenance of this product must be
performed by a qualified electrician. This product must be installed in accordance with the applicable installation code
by a person familiar with the construction and operation of the product and hazards involved. For continued protection
against shock hazard replace all covers and guards after field wiring is completed.
Risk of Fire and Electric Shock- Before installing or performing any service, the power MUST be turned OFF. All
installations should be in compliance with the National Electric Code and all state local codes.
Risk of Burn- Disconnect power and allow product to cool before handling or servicing.
Risk of Personal Injury- Due to sharp edges, handle with care.
Failure to comply with these instructions may result in death, serious bodily injury and property damage.
DISCLAIMER OF LIABILITY: Cooper LIghting Solutions assumes no liability for damages or losses of any kind that may arise from the
improper, careless, or negligent installation, handling or use of this product.
NOTICE: Product may become damaged and/or unstable if not installed properly.
Note: Specifications and dimensions subject to change without notice.
ATTENTION Receiving Department: Note actual product description of any shortage or noticeable damage on delivery receipt. File
claim for common carrier (LTL) directly with carrier. Claims for concealed damage must be filed within 15 days of delivery. All damaged
material, complete with original packing must be retained.
NOTICE: Designed for indoor installation and use only. Dry location rated.
Do not mount near gas or electric heaters.
Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel.
The use of accessory equipment is not recommended by Cooper Lighting Solutions as it may cause an unsafe condition.
Do not use this equipment for other than the intended use.
Warranties and Limitation of Liability
Please refer to www.cooperlighting.com for our terms and conditions.
FCC Statement
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Part 15 Clause 15.21 Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
FCC Part 15.19a This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC 2.1093/RSS-102 This product complies with the RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described
in this manual.
ISED RSS
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the
device. CAN ICES-003(B)/NMB-003(B).
Modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment under FCC rules.
WARNING
IMPORTANT: Lire attentivement avant d’installer le luminaire. À conserver pour consultation ultérieure.
Risque d’incendie, de décharge électrique, de coupure ou d’autres risques – L’installation et l’entretien de ce produit
doivent être effectués par un électricien qualifié. Ce produit doit être installé conformément aux règles d’installation en
vigueur par une personne familière avec la construction et le fonctionnement du produit ainsi qu’avec les risques inhérents.
Pour une protection continue contre les décharges électriques, réinstallez tous les couvercles et protecteurs en place une
fois le câblage terminé.
Risque d’incendie et de décharge électrique – Assurez-vous que l’alimentation électrique est HORS TENSION avant de
commencer l’installation ou de tenter d’en faire l’entretien. Mettez l’alimentation électrique hors tension au niveau du fusible
ou du disjoncteur. Toutes les installations doivent être conformes au Code national de l’électricité, ainsi qu’à tous les codes
nationaux et locaux.
Risque de brûlure– Débranchez la source d’alimentation et laissez refroidir le luminaire avant de procéder à son entretien
ou à sa manipulation.
Risque de blessures – À cause des arêtes tranchantes, manipulez ce produit avec précaution.
La désobéissance aux instructions suivantes représente un risque de blessures (y compris la mort) et de dommages
matériels.
EXONÉRATION DE RESPONSABILITÉ: Cooper LIghting Solutions n’assume aucune responsabilité pour les dommages ou pertes de
quelque nature que ce soit pouvant découler d’une installation, d’une manipulation ou d’une utilisation inappropriée, imprudente ou
négligente de ce produit.
AVIS: Ce produit peut s’endommager ou devenir instable s’il n’est pas installé correctement.
Remarque: Les caractéristiques techniques et les dimensions peuvent changer sans préavis.
ATTENTION Service de la réception: Veuillez fournir une description de tout élément manquant ou de tout dommage constaté au
bordereau de réception. Soumettez une réclamation de transporteur public (chargement partiel) directement auprès du transporteur.
Les demandes pour les dommages cachés doivent être présentées dans les 15 jours suivants la livraison. Tout matériel endommagé doit
être conservé avec tout l’emballage d’origine.
AVIS: Produit conçu uniquement pour une installation et un usage à l’intérieur.
Do not mount near gas or electric heaters.
Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel.
The use of accessory equipment is not recommended by Cooper Lighting Solutions as it may cause an unsafe condition.
Do not use this equipment for other than the intended use.
Garanties et limitation de responsabilité
Veuillez consulter le site www.cooperlighting.com pour obtenir les conditions générales.
Énoncé de la FCC
Remarque: Cet équipement a été mis à l’essai et déclaré conforme aux limites établies pour un dispositif numérique de catégorie B en vertu de la section 15 des
règlements de la FCC. Ces limites sont conçues pour assurer une protection raisonnable contre toute interférence nuisible dans une installation résidentielle.
Cet équipement génère, utilise et peut émettre de l’énergie radiofréquence et, s’il n’est pas installé et utilisé conformément aux instructions, peut provoquer des
interférences nuisibles aux communications radio. Toutefois, il n’est absolument pas garanti qu’aucune interférence ne se produira dans une installation donnée.
Si cet équipement provoque des interférences nuisibles à la réception de la radio ou de la télévision, ce qui peut être déterminé en éteignant et en rallumant
l’équipement, l’utilisateur est encouragé à essayer de corriger les interférences par une ou plusieurs des mesures suivantes:
• Réorientez ou déplacez l’antenne réceptrice.
• Augmentez la distance entre l’équipement et le récepteur.
• Branchez l’équipement sur la prise électrique d’un circuit autre que celui sur lequel le récepteur est branché.
• Demandez de l’aide au distributeur ou à un technicien radio ou TV qualifié.
ID du FCC (Commission fédérale des communications des États-Unis) 15 : Clause 15.21
Tout changement ou modification non expressément approuvé par la partie responsable de la conformité pourrait annuler le droit de l’utilisateur à utiliser
l’équipement.
Ce dispositif est conforme à la section 15 des règlements de la FCC. ID du FCC (Commission fédérale des communications des États-Unis) 15.19a
Son fonctionnement est assujetti aux deux conditions suivantes :
1) cet appareil ne doit pas provoquer d’interférences nuisibles et 2) cet appareil doit accepter toutes les interférences reçues, même celles qui pourraient provoquer
un fonctionnement indésirable.
ID du FCC (Commission fédérale des communications des États-Unis) 2.1093 / RSS-102
Ce produit est conforme à la limite d’exposition RF définie pour un environnement non contrôlé et est sans danger pour le fonctionnement prévu tel que décrit dans
ce manuel.
ISED RSS
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes : 1) l’appareil ne doit pas produire de brouillage; 2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement. CAN ICES-003(B)/NMB-003(B).
Les modifications non expressément approuvées par le fabricant peuvent annuler le droit de l’utilisateur à faire fonctionner l’équipement conformément aux règles
de la FCC.
Spanish
English
French
English
General Information
Vue d’ensemble
The WaveLinx Pro Insights ceiling sensor is an integral part of the WaveLinx
Pro System and offers Occupant count, Passive Infra-Red (PIR) occupancy
sensing, daylighting, temperature, and humidity capability. This sensor has
Occupant count and Occupancy coverage patterns of up to 600 square feet, it
is low voltage powered and is one of the smartest ceiling mounted sensors for
multi-sensing in the market. The sensor operates on a wireless mesh network
based on IEEE802.15.4 standards.
Caractéristiques nominales du plénum
The WaveLinx Pro Insights ceiling sensor components intended for installation
above ceiling are plenum rated.
Spécifications
Compatible only with Cooper Lighting Solutions Lighting WaveLinx Pro
Wireless Systems.
Alimentation Puissance d’entrée : 120/277 VCA
Connexions : Chargé, neutre
Indicateurs Fonctionnalité DEL
• Indication de la connexion au réseau sans fil
• Indication de blocage de lumière du jour
Spécifications
environnementales
Plage de température de fonctionnement :
-20°C à 55°C (-4°F à 131°F)
Plage de température de stockage :
-40°C à 70°C (-40°F à 158°F)
Humidité relative : 5% à 95% sans condensation,
pour usage intérieur uniquement
Normes Caractéristiques nominales : Homologué UL/cUL,
FCC, IC
UL244A – Commande d’appareil/sels grimpants
et espace
UL508/NEMA410 – Équipement de commande
industriel
UL2043 (installation de plénum)
Répond aux exigences de la norme90.1 de la
ASHRAE
Répond aux exigences de la IECC
Répond aux exigences du chapitre24 de la CEC
Sans fil
Spécifications
Radio 2,4GHz
Protocole IEEE802.15.4
Configuration de type routeur, point limite
Portée de perte de signal de 25m (75pi)
2 murs intérieurs d’une construction standard
Meilleure pratique : 100 dispositifs par
contrôleur de zone sans fil
Hauteur de
montage 8-12ft (2.4 - 3.7m)
Wiring
The unit is powered by a 24VDC power supply. Please make sure the correct
polarity is used for the power supply connections.
6 WaveLinx Pro Insights Sensors connected to 1 power supply
24 Volt
Power Supply
+
-
Insights Ceiling Sensor Installation
There are various methods that may be used to affix the Wavelinx Insights
Sensor to a ceiling surface.
Tilemount installation
1. Cut 3.8” (95.3mm) diameter hole in ceiling tile.
2. Snap sensor body into ceiling trim.
3. Torsion spring clips secure the Insights Sensor to a recessed ceiling tile.
carreau de plafond carreau de plafond
2
3
1
Surface Mount / J-Box installation
1. Attach junction box adapter plate to 4” (101.6mm) square junction box.
(screws not included)
2. Align sensor with keyhole pattern.
3. The Wireless Sensor may be installed directly to a ceiling surface via
a 4” (101.6mm) square junction box adapter plate.
4” (101.6mm)
square junction box
adapter plate
Installation Notes
Consult www.cooperlighting.com for the most up-to-date revision of the
Insights Ceiling system design guide and install this product according to the
guidelines described.
The Sensor is to be installed in dry, indoor locations ONLY. Do not install the
Sensor in damp locations. Damp locations are defined as: interior locations
subject to moderate degrees of moisture, such as some basements, some
barns, some cold-storage warehouses, and the like, and partially protected
locations under canopies, marquees, roofed open porches, and the like.
Camera and Sensor Location Notes
The Sensor provides 360° coverage pattern. It is recommended to install the
sensor more than 4ft (1.2m) away from air supply vents.
Single Sensor Setup
1. The imaginary “+” made with the vent holes and LEDs should be
approximately perpendicular with walls when possible.
Imaginary “+” made with the vent holes and LED
room walls
Single camera room
CORRECT orientation
Single camera room
INCORRECT orientation
room walls room walls
✗✔
Multi Sensor Setup
1. The imaginary “+” made with the vent holes and LEDs should be
approximately perpendicular with the walls when possible
2. The lens as a reference point should be facing the same way in all those
included in a multi-sensor setup
3. Best practice for rectangular rooms: The camera side of the sensor
should point at one of the “longer” walls of the room, and as previously
mentioned, the two cameras should both point the same direction. See
image below
longer dimension
Sensor 1 Sensor 2
shorter
dimension
overlap
area
Multi Sensor Camera Orientation
All cameras oriented the SAME direction
All cameras oriented DIFFERENT directions
conference room walls
conference room walls
✗
✔
LED and Button Definitions
• One press and release will reboot the unit
• Press and release 6 times, for 5 seconds each, for a factory reset
Sensor Status LED Indication while in out-of-box mode
There are two LED indicators on this sensor, one positioned above the camera
lens (People count sensor status LED or BLE LED), and one on the other side
below the reset button (Zigbee LED).
On power up
• Zigbee LED blink momentarily in red and once after that it will blink green
on detecting occupancy/motion.
• BLE LED/Occupant Count LED momentarily in Amber and will remain OFF
until sensor is claimed to WAC and registered under license.
Reset button to enable pairing mode
On power up the sensor will not be in pairing mode, it requires two-time power
cycle or IR remote command or press the reset button two times (equivalent
to power cycle) to get the sensor to pairing mode to get join a WAC which is
in pairing/commissioning mode.
Out-of-box functionality
As Insights CS is a ceiling sensor without own light fixture associated to it
there is no user functionality before it is added to the WAC.
Troubleshooting
• There are no user-serviceable parts inside of the Sensor Interface
Module. Please return the device to Cooper Lighting Solutions if service
is required.
• The device is ONLY intended for use with WAC and Trellix releases of SR9
and beyond? (If the device is claimed to a WAC prior to SR9, it will not be
represented correctly and Occupany Counting will not work unless it is
completely reset after the WAC is upgraded to SR9 or later.)
If still having trouble, call Technical Services at 1-800-553-3879.
General Information
Descripción General
The WaveLinx Pro Insights ceiling sensor is an integral part of the WaveLinx
Pro System and offers Occupant count, Passive Infra-Red (PIR) occupancy
sensing, daylighting, temperature, and humidity capability. This sensor has
Occupant count and Occupancy coverage patterns of up to 600 square feet, it
is low voltage powered and is one of the smartest ceiling mounted sensors for
multi-sensing in the market. The sensor operates on a wireless mesh network
based on IEEE802.15.4 standards.
Plenum rating
The WaveLinx Pro Insights ceiling sensor components intended for installation
above ceiling are plenum rated.
Especificaciones
Compatible only with Cooper Lighting Solutions Lighting WaveLinx Pro
Wireless Systems.
Corriente Corriente de entrada: 120/277 VCA
Conexiones: Caliente, neutro
Indicadores Funcionalidad LED
• Indicación de conexión a la red inalámbrica
• Indicación de retraso de la luz del día
Especificaciones
ambientales Rango de temperatura de funcionamiento:
-4°F - 131°F (-20°C - 55°C)
Rango de temperatura de almacenamiento:
-40°F - 158°F (-40°C - 70°C)
Humedad relativa: 5% a 95% sin condensación, solo
para uso en interiores.
Estándares Listados: Listado UL/cUL, FCC, IC
UL244A - Control de dispositivo /líneas de fuga
y distancia en el aire
Equipo de control industrial UL 508/NEMA 410
UL 2043 (instalación plenum)
Cumple con los requisitos
del estándar 90.1 de ASHRAE
Cumple con los requisitos de IECC
Cumple con los requisitos del Título 24 de CEC
Dispositivo i
nalámbrico
Especificaciones
Radio 2,4GHz
Estándar IEEE 802.15.4
Tipo de configuración Enrutador, Nodo final
Alcance 75 pies (25 m) LOS
2 paredes interiores de construcción estándar.
Mejores prácticas: 100 dispositivos por
controlador de área inalámbrico
Altura de
montaje 8-12ft (2.4 - 3.7m)
Wiring
The unit is powered by a 24VDC power supply. Please make sure the correct
polarity is used for the power supply connections.
6 WaveLinx Pro Insights Sensors connected to 1 power supply
24 Volt
Power Supply
+
-
Insights Ceiling Sensor Installation
There are various methods that may be used to affix the Wavelinx Insights
Sensor to a ceiling surface.
Tilemount installation
1. Cut 3.8” (95.3mm) diameter hole in ceiling tile.
2. Snap sensor body into ceiling trim.
3. Torsion spring clips secure the Insights Sensor to a recessed ceiling tile.
placa del cielo rasoplaca del cielo raso
2
3
1
Surface Mount / J-Box installation
1. Attach junction box adapter plate to 4” (101.6mm) square junction box.
(screws not included)
2. Align sensor with keyhole pattern.
3. The Wireless Sensor may be installed directly to a ceiling surface via
a 4” (101.6mm) square junction box adapter plate.
4” (101.6mm)
square junction box
adapter plate
Installation Notes
Consult www.cooperlighting.com for the most up-to-date revision of the
Insights Ceiling system design guide and install this product according to the
guidelines described.
The Sensor is to be installed in dry, indoor locations ONLY. Do not install the
Sensor in damp locations. Damp locations are defined as: interior locations
subject to moderate degrees of moisture, such as some basements, some
barns, some cold-storage warehouses, and the like, and partially protected
locations under canopies, marquees, roofed open porches, and the like.
Camera and Sensor Location Notes
The Sensor provides 360° coverage pattern. It is recommended to install the
sensor more than 4ft (1.2m) away from air supply vents.
Single Sensor Setup
1. The imaginary “+” made with the vent holes and LEDs should be
approximately perpendicular with walls when possible.
Imaginary “+” made with the vent holes and LED
room walls
Single camera room
CORRECT orientation
Single camera room
INCORRECT orientation
room walls room walls
✗✔
Multi Sensor Setup
1. The imaginary “+” made with the vent holes and LEDs should be
approximately perpendicular with the walls when possible
2. The lens as a reference point should be facing the same way in all those
included in a multi-sensor setup
3. Best practice for rectangular rooms: The camera side of the sensor
should point at one of the “longer” walls of the room, and as previously
mentioned, the two cameras should both point the same direction. See
image below
longer dimension
Sensor 1 Sensor 2
shorter
dimension
overlap
area
Multi Sensor Camera Orientation
All cameras oriented the SAME direction
All cameras oriented DIFFERENT directions
conference room walls
conference room walls
✗
✔
LED and Button Definitions
• One press and release will reboot the unit
• Press and release 6 times, for 5 seconds each, for a factory reset
Sensor Status LED Indication while in out-of-box mode
There are two LED indicators on this sensor, one positioned above the camera
lens (People count sensor status LED or BLE LED), and one on the other side
below the reset button (Zigbee LED).
On power up
• Zigbee LED blink momentarily in red and once after that it will blink green
on detecting occupancy/motion.
• BLE LED/Occupant Count LED momentarily in Amber and will remain OFF
until sensor is claimed to WAC and registered under license.
Reset button to enable pairing mode
On power up the sensor will not be in pairing mode, it requires two-time power
cycle or IR remote command or press the reset button two times (equivalent
to power cycle) to get the sensor to pairing mode to get join a WAC which is
in pairing/commissioning mode.
Out-of-box functionality
As Insights CS is a ceiling sensor without own light fixture associated to it
there is no user functionality before it is added to the WAC.
Troubleshooting
• There are no user-serviceable parts inside of the Sensor Interface
Module. Please return the device to Cooper Lighting Solutions if service
is required.
• The device is ONLY intended for use with WAC and Trellix releases of SR9
and beyond? (If the device is claimed to a WAC prior to SR9, it will not be
represented correctly and Occupany Counting will not work unless it is
completely reset after the WAC is upgraded to SR9 or later.)
If still having trouble, call Technical Services at 1-800-553-3879.
Servicio de ventas de Canada
5925 McLaughlin Road
Mississauga (Ontario) L5R 1B8
T: 905501-3000
T: 905501-3172
Cooper Lighting Solutions es una
marca registrada.
Todas las marcas registradas
son propiedad de sus respectivos
propietarios.
La disponibilidad de productos,
las especificaciones y los
cumplimientos están sujetos a
cambio sin previo aviso.
Cooper Lighting Solutions
1121 Highway 74 South
Peachtree City, GA 30269
www.cooperlighting.com
Para servicio o
asistencia técnica:
1-800-553-3879
© 2022 Cooper Lighting Solutions
Todos los derechos reservados
Impreso en México
Publicación No.IL50372722
Agosto 2022
Service des ventes du Canada
5925 McLaughlin Road
Mississauga (Ontario) L5R 1B8
Tél.: 905501-3000
Téléc.: 905501-3172
Cooper Lighting Solutions est une
marque déposée.
Toutes les autres marques de commerce
sont la propriété de leur propriétaire
respectif.
La disponibilité du produit, les
spécifications et les conformités
peuvent être modifiées sans préavis.
Cooper Lighting Solutions
1121 Highway 74 South
Peachtree City, GA 30269
www.cooperlighting.com
Pour obtenir de l’aide technique
ou un service:
1800553-3879
© Cooper Lighting Solutions, 2022.
Tous droits réservés.
Imprimé en Mexique
Publication no IL50372722
Aout 2022
French
Spanish
-
1
-
2
Cooper Lighting ECS-Z-M05-LV Manual de usuario
- Tipo
- Manual de usuario
En otros idiomas
Documentos relacionados
-
Cooper Lighting SCMA0401 Manual de usuario
-
Cooper Lighting WIM-WH-SKIT Manual de usuario
-
Cooper Lighting WWLBLEWaveLinx Lite Wallstation Bluetooth Low Energy Manual de usuario
-
Cooper Lighting WWBZIG WaveLinx Wireless Wallstation Battery Powered Guía de instalación
-
Cooper Lighting Loft WaveStream LED Guía de instalación
-
Cooper Lighting WaveLinx OEM Manual de usuario
-
-
-
Otros documentos
-
Cooper 1255874 WaveLinx Lite Wallstation Manual de usuario
-
Cooper Lighting Solutions IB50533821 Manual de usuario
-
Airzone AZAI6WSCDA1 Aidoo Wi-Fi Control Instrucciones de operación
-
Cooper Metalux WaveLinx Installation Instructions Manual
-
nanit N301pro Baby Monitor Manual de usuario
-
Eaton Metalux WaveLinx Installation Instructions Manual
-
Lutron Electronics PowPak FC-SENSOR Manual de usuario
-
Halo IB517057ML LED Downlight Manual de usuario
