ASROCK H81M-ITX/WiFi Manual de usuario

Marca: ASROCK

Modelo: H81M-ITX/WiFi

Tipo: Manual de usuario

Version 1.0

Published May 2014

No part of this documentation may be reproduced, transcribed, transmitted, or

translated in any language, in any form or by any means, except duplication of

documentation by the purchaser for backup purpose, without written consent of

ASRock Inc.

Products and corporate names appearing in this documentation may or may not

be registered trademarks or copyrights of their respective companies, and are used

only for identication or explanation and to the owners’ benet, without intent to

infringe.

Disclaimer:

Specications and information contained in this documentation are furnished for

informational use only and subject to change without notice, and should not be

constructed as a commitment by ASRock. ASRock assumes no responsibility for

any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock does not provide

warranty of any kind, either expressed or implied, including but not limited to

the implied warranties or conditions of merchantability or tness for a particular

purpose.

In no event shall ASRock, its directors, ocers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for

loss of prots, loss of business, loss of data, interruption of business and the like),

even if ASRock has been advised of the possibility of such damages arising from any

defect or error in the documentation or product.

e terms HDMI

and HDMI High-Denition Multimedia Interface, and the HDMI

logo are trademarks or registered trademarks of HDMI Licensing LLC in the United

States and other countries.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance

controlled in Perchlorate Best Management Practices (BMP) regulations passed by the

California Legislature. When you discard the Lithium battery in California, USA, please

follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/

perchlorate”

ASRock Website: http://www.asrock.com

H81M-ITX/WiFi

English

Motherboard Layout

Intel

H81

DDR3_B1 (64 bit, 240-pin module)

DDR3_A1 (64 bit, 240-pin module)

CMOS

Battery

ATXPWR1

Top:

RJ-45

USB 2.0

T: USB0

B: USB1

CLRCMOS1

HDL ED RES ET

PLE D PWRBT N

PANE L1

HD_AUDIO1

H81M-ITX/WiFi

RoHS

CHA_FAN1

32Mb

BIOS

HDMI1

VGA1

DVI1

Audio

CODEC

PCIE1

USB 3.0

TPMS1

SATA_ 3

USB 3.0

T: USB1

B: USB2

Top:

LINE IN

Cent er:

FRON T

Bott om:

MIC IN

USB_6_7

ATX12V1

SATA_ 2

SATA3 _1 SATA3 _0

USB_4_5

MPCIE1

CPU_FAN1

CI1

USB 2.0

T: USB2

B: USB3

PS2

Keyb oard

/Mou se

English

No. Description

1 CPU Fan Connector (CPU_FAN1)

2 ATX 12V Power Connector (ATX12V1)

3 2 x 240-pin DDR3 DIMM Slots (DDR3_A1, DDR3_B1)

4 Clear CMOS Jumper (CLRCMOS1)

5 Chassis Intrusion Header (CI1)

6 ATX Power Connector (ATXPWR1)

7 TPM Header (TPMS1)

8 USB 2.0 Header (USB_6_7)

9 System Panel Header (PANEL1)

10 USB 2.0 Header (USB_4_5)

11 SATA3 Connector (SATA3_0)

12 SATA3 Connector (SATA3_1)

13 SATA2 Connector (SATA_2)

14 SATA2 Connector (SATA_3)

15 Front Panel Audio Header (HD_AUDIO1)

16 Chassis Fan Connector (CHA_FAN1)

H81M-ITX/WiFi

English

I/O Panel

No. Description No. Description

1 USB 2.0 Ports (USB_2_3) 7 USB 2.0 Ports (USB_01)

2 D-Sub Port 8 USB 3.0 Ports (USB3_1_2)

3 LAN RJ-45 Port* 9 HDMI Port

4 Line In (Light Blue) 10 DVI-D Port

5 Front Speaker (Lime) 11 PS/2 Mouse/Keyboard Port

6 Microphone (Pink)

* ere are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10Mbps connection

Blinking Data Activity Orange 100Mbps connection

On Link Green 1Gbps connection

ACT/LINK LED

SPEED LED

LAN Port

1 2 3 5

67891011

English

WiFi-802.11n Module and ASRock WiFi 2.4GHz Antenna

WiFi-802.11n Module

WiFi-802.11n module is an easy-to-use wireless local area network (WLAN)

adapter to support WiFi function. With WiFi-802.11n module, you can easily create

a wireless environment and enjoy the convenience of wireless network connectivity.

erefore, from anywhere within the signal range, you will be able to play LAN

games, connect to the internet, access and share printers, and make Internet phone

calls easily.

WiFi-802.11n module supports Station mode. You can use the wireless function to

connect the access point (AP), or connect with other stations in the wireless range

instead. ere are two choices provided in station mode: Infrastructure mode

and Ad-hoc mode. Please read below introduction for the dierences of these two

modes.

Infrastructure Mode

If you have a present access point (AP) in your wireless network environment for

this station to join, you can set up WiFi-802.11n module in Infrastructure mode.

In this mode, WiFi-802.11n module acts as a wireless adapter. In other words, it is

centered on an AP that provides Internet access and LAN communication for the

wireless stations, such as PC, notebook and other devices.

Ad-hoc Mode

If you don’t have a present access point in your wireless network environment, you

can set up WiFi-802.11n module in Ad-hoc mode. e wireless network brings

together workstations, PC, notebook and other devices for wireless communication.

* e transmission speed may vary according to the environment.

ASRock WiFi 2.4GHz Antenna

Antenna Port

WiFi-802.11n Module

H81M-ITX/WiFi

English

WiFi Module and WiFi Antenna Installation Guide

Step 1

Prepare the WiFi Module, WiFi Module Bracket,

and the two screws that come with the package.

Prepare a Phillips #0 screwdriver.

Step 2

Attach the WiFi Module Bracket to the WiFi

card, aligning the screw hole on the WiFi card

with the screw hole on the bracket. Use the screw

to attach the bracket and the WiFi card, but do

not tighten the screw.

Step 3

Insert the WiFi Module Card into the vertical

mini PCI Express slot (MPCIE1).

Step 4

Tighten the screw that holds the card in place.

English

Step 5

Tighten the screw that attaches the WiFi

Module Bracket to the WiFi card (installed

in Step 2).

Step 6

Prepare the SMA Wi-Fi Antenna Cable and

WiFi 2.4 GHz Antenna that come with the

package.

Step 7

Attach the SMA Wi-Fi Antenna Cable to

the WiFi Module.

H81M-ITX/WiFi

English

Step 8

Insert the RP-SMA Wi-Fi Antenna Con-

nector to the antenna port on the I/O

shield.

Step 9

Fasten the screw nuts to secure the

antenna connector.

Step 10

Connect the two WiFi 2.4 GHz

Antenna to the antenna connector. Turn

the antenna clockwise until it is securely

connected.

English

Step 11

Set the WiFi 2.4 GHz Antenna at 90-degree

angle.

*You may need to adjust the direction of

the antenna for a stronger signal.

H81M-ITX/WiFi

English

Chapter 1 Introduction

ank you for purchasing ASRock H81M-ITX/WiFi motherboard, a reliable

motherboard produced under ASRock’s consistently stringent quality control.

It delivers excellent performance with robust design conforming to ASRock’s

commitment to quality and endurance.

1.1 Package Contents

•

ASRock H81M-ITX/WiFi Motherboard (Mini-ITX Form Factor)

•

ASRock H81M-ITX/WiFi Quick Installation Guide

•

ASRock H81M-ITX/WiFi Support CD

•

1 x I/O Panel Shield

•

2 x Serial ATA (SATA) Data Cables (Optional)

•

1 x WiFi-802.11n Module

•

1 x SMA WiFi Antenna Cable

•

1 x ASRock WiFi 2.4 GHz Antenna

•

1 x WiFi Module Bracket

•

2 x Screws for WiFi Module

Because the motherboard specications and the BIOS soware might be updated, the

content of this documentation will be subject to change without notice. In case any

modications of this documentation occur, the updated version will be available on

ASRock’s website without further notice. If you require technical support related to

this motherboard, please visit our website for specic information about the model

you are using. You may nd the latest VGA cards and CPU support list on ASRock’s

website as well. ASRock website http://www.asrock.com.

English

1.2 Specications

Platform

•

Mini-ITX Form Factor

•

Solid Capacitor design

•

High Density Glass Fabric PCB

CPU

•

Supports New 4

and 4

Generation Intel® Core

i7/i5/i3/

Xeon®/Pentium®/Celeron® Processors (Socket 1150)

•

Supports Intel® Turbo Boost 2.0 Technology

Chipset

•

Intel® H81

Memory

•

Dual Channel DDR3 Memory Technology

•

2 x DDR3 DIMM Slots

•

Supports DDR3 1600/1333/1066 non-ECC, un-buered

memory

•

Max. capacity of system memory: 16GB (see CAUTION)

•

Supports Intel® Extreme Memory Prole (XMP) 1.3 / 1.2

Expansion

Slot

•

1 x PCI Express 2.0 x16 Slot

•

1 x Vertical Half Mini-PCI Express Slot: For WiFi Module

Graphics

•

Intel® HD Graphics Built-in Visuals and the VGA outputs can

be supported only with processors which are GPU integrated.

•

Supports Intel® HD Graphics Built-in Visuals : Intel® Quick

Sync Video with AVC, MVC (S3D) and MPEG-2 Full

HW Encode1, Intel® InTru

3D, Intel® Clear Video HD

Technology, Intel® Insider

, Intel® HD Graphics 4400/4600

•

Pixel Shader 5.0, DirectX 11.1

•

Max. shared memory 1792MB

•

ree graphics output options: D-Sub, DVI-D and HDMI

Ports

•

Supports Triple Monitor

•

Supports HDMI with max. resolution up to 1920x1200 @

60Hz

•

Supports DVI-D with max. resolution up to 1920x1200 @

60Hz

•

Supports D-Sub with max. resolution up to 1920x1200 @

60Hz

H81M-ITX/WiFi

English

•

Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and

HBR (High Bit Rate Audio) with HDMI Port (Compliant

HDMI monitor is required)

•

Supports HDCP with DVI-D and HDMI Ports

•

Supports Full HD 1080p Blu-ray (BD) playback with DVI-D

and HDMI Ports

Audio

•

5.1 CH HD Audio (Realtek ALC662 Audio Codec)

•

Supports Surge Protection (ASRock Full Spike Protection)

•

ELNA Audio Caps

LAN

•

PCIE x1 Gigabit LAN 10/100/1000 Mb/s

•

Realtek RTL8111GR

•

Supports Wake-On-WAN

•

Supports Wake-On-LAN

•

Supports Lightning/ESD Protection (ASRock Full Spike

Protection)

•

Supports LAN Cable Detection

•

Supports Energy Ecient Ethernet 802.3az

•

Supports PXE

Wireless

LAN

WiFi-802.11n Module

•

1T1R 150Mbps IEEE 802.11n / 54Mbps IEEE 802.11g /

11Mbps IEEE 802.11b

•

Supports Station mode (Infrastructure mode and Ad-hoc

mode)

Rear Panel

I/O

•

1 x PS/2 Mouse/Keyboard Port

•

1 x D-Sub Port

•

1 x DVI-D Port

•

1 x HDMI Port

•

4 x USB 2.0 Ports (Supports ESD Protection (ASRock Full

Spike Protection))

•

2 x USB 3.0 Ports (Supports ESD Protection (ASRock Full

Spike Protection))

•

1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED

LED)

•

HD Audio Jacks: Line in / Front Speaker / Microphone

English

Storage

•

2 x SATA3 6.0 Gb/s Connectors, support NCQ, AHCI and

Hot Plug

•

2 x SATA2 3.0 Gb/s Connectors, support NCQ, AHCI and

Hot Plug

Connector

•

1 x Chassis Intrusion Header

•

1 x TPM Header

•

1 x CPU Fan Connector (4-pin)

•

1 x Chassis Fan Connector (4-pin)

•

1 x 24 pin ATX Power Connector

•

1 x 4 pin 12V Power Connector

•

1 x Front Panel Audio Connector

•

2 x USB 2.0 Headers (Support 4 USB 2.0 ports) (Supports ESD

Protection (ASRock Full Spike Protection))

BIOS

Feature

•

32Mb AMI UEFI Legal BIOS with multilingual GUI support

•

ACPI 1.1 Compliant wake up events

•

SMBIOS 2.3.1 support

•

CPU, DRAM, PCH 1.05V Voltage multi-adjustment

Hardware

Monitor

•

CPU/Chassis temperature sensing

•

CPU/Chassis Tachometer

•

CPU/Chassis Quiet Fan (Auto adjust chassis fan speed by

CPU temperature)

•

CPU/Chassis Fan multi-speed control

•

CASE OPEN detection

•

Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore

•

Microso® Windows® 8.1 32-bit / 8.1 64-bit / 8 32-bit / 8 64-

bit / 7 32-bit / 7 64-bit

Certica-

tions

•

FCC, CE, WHQL

•

ErP/EuP ready (ErP/EuP ready power supply is required)

* For detailed product information, please visit our website:

http://www.asrock.com

H81M-ITX/WiFi

English

Please realize that there is a certain risk involved with overclocking, including adjust-

ing the setting in the BIOS, applying Untied Overclocking Technology, or using third-

party overclocking tools. Overclocking may aect your system’s stability, or even cause

damage to the components and devices of your system. It should be done at your own

risk and expense. We are not responsible for possible damage caused by overclocking.

Due to limitation, the actual memory size may be less than 4GB for the reservation

for system usage under Windows® 32-bit operating systems. Windows® 64-bit operat-

ing systems do not have such limitations. You can use ASRock XFast RAM to utilize

the memory that Windows® cannot use.

English

is is a Mini-ITX form factor motherboard. Before you install the motherboard,

study the conguration of your chassis to ensure that the motherboard ts into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard components

or change any motherboard settings.

•

Make sure to unplug the power cord before installing or removing the motherboard

components. Failure to do so may cause physical injuries and damages to motherboard

components.

•

In order to avoid damage from static electricity to the motherboard’s components,

NEVER place your motherboard directly on a carpet. Also remember to use a grounded

wrist strap or touch a safety grounded object before you handle the components.

•

Hold components by the edges and do not touch the ICs.

•

Whenever you uninstall any components, place them on a grounded anti-static pad or

in the bag that comes with the components.

•

When placing screws to secure the motherboard to the chassis, please do not over-

tighten the screws! Doing so may damage the motherboard.

Chapter 2 Installation

H81M-ITX/WiFi

English

2.1 Installing the CPU

1. Before you insert the 1150-Pin CPU into the socket, please check if the PnP cap is on

the socket, if the CPU surface is unclean, or if there are any bent pins in the socket.

Do not force to insert the CPU into the socket if above situation is found. Otherwise,

the CPU will be seriously damaged.

2. Unplug all power cables before installing the CPU.

English

H81M-ITX/WiFi

English

Please save and replace the cover if the processor is removed. e cover must be placed

if you wish to return the motherboard for aer service.

English

2.2 Installing the CPU Fan and Heatsink

1 2

H81M-ITX/WiFi

English

2.3 Installing Memory Modules (DIMM)

is motherboard provides two 240-pin DDR3 (Double Data Rate 3) DIMM slots,

and supports Dual Channel Memory Technology.

e DIMM only ts in one correct orientation. It will cause permanent damage to

the motherboard and the DIMM if you force the DIMM into the slot at incorrect

orientation.

1. For dual channel conguration, you always need to install identical (the same

brand, speed, size and chip-type) DDR3 DIMM pairs.

2. It is unable to activate Dual Channel Memory Technology with only one memory

module installed.

3. It is not allowed to install a DDR or DDR2 memory module into a DDR3 slot;

otherwise, this motherboard and DIMM may be damaged.

English

H81M-ITX/WiFi

English

2.4 Expansion Slots (PCI Express Slots)

ere is 1 PCI Express slot and 1 mini-PCI Express slot on the motherboard.

PCIe slot:

PCIE1 (PCIe 2.0 x16 slot) is used for PCI Express x16 lane width graphics cards.

mini-PCIe slot:

MPCIE1 (mini-PCIe slot) is used for WiFi module.

Before installing an expansion card, please make sure that the power supply is

switched o or the power cord is unplugged. Please read the documentation of the

expansion card and make necessary hardware settings for the card before you start

the installation.

English

2.5 Jumpers Setup

e illustration shows how jumpers are setup. When the jumper cap is placed on

the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper

is “Open”. e illustration shows a 3-pin jumper whose pin1 and pin2 are “Short”

when a jumper cap is placed on these 2 pins.

Clear CMOS Jumper

(CLRCMOS1)

(see p.1, No. 4)

CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system

parameters to default setup, please turn o the computer and unplug the power

cord from the power supply. Aer waiting for 15 seconds, use a jumper cap to

short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear

the CMOS right aer you update the BIOS. If you need to clear the CMOS when

you just nish updating the BIOS, you must boot up the system rst, and then shut

it down before you do the clear-CMOS action. Please be noted that the password,

date, time, and user default prole will be cleared only if the CMOS battery is

removed.

Clear CMOS

Default

If you clear the CMOS, the case open may be detected. Please adjust the BIOS option

“Clear Status” to clear the record of previous chassis intrusion status.

H81M-ITX/WiFi

English

2.6 Onboard Headers and Connectors

System Panel Header

(9-pin PANEL1)

(see p.1, No. 9)

Connect the power

switch, reset switch and

system status indicator on

the chassis to this header

according to the pin

assignments below. Note

the positive and negative

pins before connecting

the cables.

GND

RESET#

PWRBTN#

PLED-

PLED+

GND

HDLED-

HDLED+

GND

PWRBTN (Power Switch):

Connect to the power switch on the chassis front panel. You may congure the way to

turn o your system using the power switch.

RESET (Reset Switch):

Connect to the reset switch on the chassis front panel. Press the reset switch to restart

the computer if the computer freezes and fails to perform a normal restart.

PLED (System Power LED):

Connect to the power status indicator on the chassis front panel. e LED is on when

the system is operating. e LED keeps blinking when the system is in S1/S3 sleep state.

e LED is o when the system is in S4 sleep state or powered o (S5).

HDLED (Hard Drive Activity LED):

Connect to the hard drive activity LED on the chassis front panel. e LED is on when

the hard drive is reading or writing data.

e front panel design may dier by chassis. A front panel module mainly consists

of power switch, reset switch, power LED, hard drive activity LED, speaker and etc.

When connecting your chassis front panel module to this header, make sure the wire

assignments and the pin assignments are matched correctly.

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over

these headers and connectors. Placing jumper caps over the headers and connectors

will cause permanent damage to the motherboard.

English

Serial ATA2 Connectors

(SATA_2:

see p.1, No. 13)

(SATA_3:

see p.1, No. 14)

ese two SATA2

connectors support SATA

data cables for internal

storage devices with up to

3.0 Gb/s data transfer rate.

Serial ATA3 Connectors

(SATA3_0:

see p.1, No. 11)

(SATA3_1:

see p.1, No. 12)

ese two SATA3

connectors support SATA

data cables for internal

storage devices with up to

6.0 Gb/s data transfer rate.

USB 2.0 Headers

(9-pin USB_4_5)

(see p.1, No. 10)

(9-pin USB_6_7)

(see p.1, No. 8)

Besides four USB 2.0 ports

on the I/O panel, there

are two headers on this

motherboard. Each USB

2.0 header can support

two ports.

Front Panel Audio Header

(9-pin HD_AUDIO1)

(see p.1, No. 15)

is header is for

connecting audio devices

to the front audio panel.

J_SENSE

OUT2_L

MIC_RET

PRESENCE#

GND

OUT2_R

MIC2_R

MIC2_L

OUT_RET

SATA3_1

SATA3_0

SATA_3

SATA_2

1. High Denition Audio supports Jack Sensing, but the panel wire on the chassis must

support HDA to function correctly. Please follow the instructions in our manual and

chassis manual to install your system.

2. If you use an AC’97 audio panel, please install it to the front panel audio header by

the steps below:

A. Connect Mic_IN (MIC) to MIC2_L.

B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.

C. Connect Ground (GND) to Ground (GND).

D. MIC_RET and OUT_RET are for the HD audio panel only. You don’t need to

connect them for the AC’97 audio panel.

E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel

and adjust “Recording Volume”.

DUMMY

GND GND

-B

-A

USB_PWR

H81M-ITX/WiFi

English

Chassis Fan Connector

(4-pin CHA_FAN1)

(see p.1, No. 16)

Please connect fan cable

to the fan connector and

match the black wire to

the ground pin.

CPU Fan Connector

(4-pin CPU_FAN1)

(see p.1, No. 1)

is motherboard pro-

vides a 4-Pin CPU fan

(Quiet Fan) connector.

If you plan to connect a

3-Pin CPU fan, please

connect it to Pin 1-3.

ATX Power Connector

(24-pin ATXPWR1)

(see p.1, No. 6)

is motherboard pro-

vides a 24-pin ATX power

connector. To use a 20-pin

ATX power supply, please

plug it along Pin 1 and Pin

13.

ATX 12V Power

Connector

(4-pin ATX12V1)

(see p.1, No. 2)

Please connect an ATX

12V power supply to this

connector.

Chassis Intrusion Header

(2-pin CI1)

(see p.1, No. 5)

is motherboard

supports CASE OPEN

detection feature that

detects if the chassis cove

has been removed. is

feature requires a chassis

with chassis intrusion

detection design.

FAN_SPEED

FAN_SPEED_CONTROL

+12V

GND

FAN_SPEED

FAN_SPEED_CONTROL

+12V

GND

Signal

GND

English

TPM Header

(17-pin TPMS1)

(see p.1, No. 7)

is connector supports

Trusted Platform Module

(TPM) system, which can

securely store keys, digital

certicates, passwords,

and data. A TPM system

also helps enhance

network security, protects

digital identities, and

ensures platform integrity.

GND

SMB_DATA_MAIN

LAD2

LAD1

GND

S_PWRDWN#

SERIRQ#

GND

PCICLK

PCIRST#

LAD3

+3V

LAD0

+3VSB

GND

FRAME

SMB_CLK_MAIN

Deutsch

H81M-ITX/WiFi

1 Einleitung

Vielen Dank, dass Sie sich für das H81M-ITX/WiFi von ASRock entschieden haben

– ein zuverlässiges Motherboard, das konsequent unter der strengen Qualitäts-

kontrolle von ASRock hergestellt wurde. Es liefert ausgezeichnete Leistung mit

robustem Design, das ASRocks Streben nach Qualität und Beständigkeit erfüllt.

1.1 Lieferumfang

• ASRock H81M-ITX/WiFi-Motherboard (Mini-ITX-Formfaktor)

• ASRock H81M-ITX/WiFi-Schnellinstallationsanleitung

• ASRock H81M-ITX/WiFi-Unterstützungs-CD

• 1 x E/A-Blendenabschirmung

• 2 x Serial-ATA- (SATA) Datenkabel (optional)

• 1 x WiFi-802.11ac-Modul

• 1 x SMA-WiFi-Antennenkabel

• 1 x ASRock-WiFi-2,4-GHz-Antennen

• 1 x WiFi-Modulhalterung

• 2 x Schrauben für WiFi-Modul

Da die technischen Daten des Motherboards sowie die BIOS-Soware aktualisiert

werden können, kann der Inhalt dieser Dokumentation ohne Ankündigung geändert

werden. Falls diese Dokumentation irgendwelchen Änderungen unterliegt, wird die

aktualisierte Version ohne weitere Hinweise auf der ASRock-Webseite zur Verfügung

gestellt. Sollten Sie technische Hilfe in Bezug auf dieses Motherboard benötigen,

erhalten Sie auf unserer Webseite spezischen Informationen über das von Ihnen

verwendete Modell. Auch nden Sie eine aktuelle Liste unterstützter VGA-Karten und

Prozessoren auf der ASRock-Webseite: ASRock-Webseite http://www.asrock.com.

Deutsch

1.2 Technische Daten

Plattform

• Mini-ITX-Formfaktor

• Solides Kondensatordesign

• PCB mit hochverdichtetem Glasfasergewebe

Prozessor

• Unterstützt Intel® Core

i7/i5/i3/Xeon®/Pentium®/Celeron®-

Prozessoren (Sockel 1150) der 4. und neuen 4. Generation

• Unterstützt Intel® Turbo Boost 2.0-Technologie

Chipsatz

• Intel® H81

Speicher

• Dualkanal-DDR3-Speichertechnologie

• 2 x DDR3-DIMM-Steckplätze

• Unterstützt DDR3 1600/1333/1066 non-ECC, ungepuerter

Speicher

• Systemspeicher, max. Kapazität: 16GB

(siehe ACHTUNG)

• Unterstützt Intel® Extreme Memory Prole (XMP)1.3/1.2

Erweiterungs-

steckplatz

• 1 x PCI-Express 2,0-x16-Steckplatz

• 1 x Mini-PCI Express-Steckplatz (vertikal, halbe Länge): Für

WiFi-Modul

Grakkarte

• Integrierte Intel® HD Graphics-Visualisierung und VGA-

Ausgänge können nur mit Prozessoren unterstützt werden,

die GPU-integriert sind.

• Unterstützt integrierte Intel® HD Graphics-Visualisierung:

Intel® Quick Sync Video mit AVC, MVC (S3D) und MPEG-2

Full HW Encode1, Intel® InTru

3D, Intel® Clear Video HD

Technology, Intel® Insider

, Intel® HD Graphics 4400/4600

• Pixel Shader 5.0, DirectX 11.1

• Max. geteilter Speicher: 1792 MB

• Drei VGA-Ausgangsoptionen: D-Sub, DVI-D und HDMI

• Unterstützt drei Monitore

• Unterstützt HDMI-Technologie mit maximaler Auösung

von 1920 x 1200 bei 60 Hz

• Unterstützt DVI-D mit maximaler Auösung von 1920 x

1200 bei 60 Hz

• Unterstützt D-Sub mit maximaler Auösung von 1920 x 1200

bei 60 Hz

Deutsch

H81M-ITX/WiFi

• Unterstützt Auto-Lippensynchronizität, hohe Farbtiefe (12

bpc), xvYCC und HBR (Audio mit hoher Bitrate) mit HDMI

(konformer HDMI-Monitor erforderlich)

• Unterstützt HDCP-Funktion mit DVI-D- und HDMI-Ports

• Unterstützt Blu-ray- (BD) Wiedergabe (Full HD/1080p) mit

DVI-D- und HDMI-Ports

Audio

• 5.1-Kanal-HD-Audio (Realtek ALC662-Audiocodec)

• Unterstützt Überspannungsschutz (ASRocks Komplettschutz

vor Spannungsspitzen)

• ELNA-Audiokondensatoren

LAN

• PCIE x1 Gigabit LAN 10/100/1000 Mb/s

• Realtek RTL8111GR

• Unterstützt Wake-On-WAN

• Unterstützt Wake-On-LAN

• Unterstützt Schutz vor Blitzschlag/elektrostatischer

Entladung (ASRocks Komplettschutz vor Spannungsspitzen)

• Unterstützt LAN-Kabelerkennung

• Unterstützt energiee zientes Ethernet 802.3az

• Unterstützt PXE

Wireless LAN

802.11n-Wi-Fi-Modul

• 1T1R 150 MBit/s – IEEE 802.11n / 54 MBit/s – IEEE 802.11g /

11 MBit/s – IEEE 802.11b

• Unterstützt Stationsmodus (Infrastruktur- und Ad-hoc-

Modus)

Rückblende,

E/A

• 1 x PS/2-Maus-/Tastaturanschluss

• 1 x D-Sub-Port

• 1 x DVI-D-Port

• 1 x HDMI-Port

• 4 x USB 2.0-Ports (Unterstützt Schutz vor elektrostatischer

Entladung (ASRocks Komplettschutz vor Spannungsspitzen))

• 2 x USB 3.0-Ports (Unterstützt Schutz vor elektrostatischer

Entladung (ASRocks Komplettschutz vor Spannungsspitzen))

• 1 x RJ-45-LAN-Port mit LED (Aktivität/Verbindung-LED

und Geschwindigkeit-LED)

• HD-Audioanschluss: Line-in / Vorderer Lautsprecher /

Mikrofon

Deutsch

Speicher

• 2 x SATA-III-6,0-Gb/s-Anschlüsse, unterstützt NCQ, AHCI

und Hot-Plugging

• 2 x SATA-II-3,0-Gb/s-Anschlüsse, unterstützt NCQ, AHCI

und Hot-Plugging

Anschluss

• 1 x Gehäuseeingri-Stileiste

• 1 x TPM-Stileiste

• 1 x CPU-Lüeranschluss (4-polig)

• 1 x Gehäuselüeranschluss (4-polig)

• 1 x 24-poliger ATX-Netzanschluss

• 1 x 4-poliger 12-V-Netzanschluss

• 1 x Audioanschluss an Frontblende

• 2 x USB 2.0-Stileisten (unterstützt vier USB 2.0-Ports)

(Unterstützt Schutz vor elektrostatischer Entladung (ASRocks

Komplettschutz vor Spannungsspitzen))

BIOS-

Funktion

• 32-Mb-AMI-UEFI-Legal-BIOS mit Unterstützung

mehrsprachiger grascher Benutzerschnittstellen

• ACPI 1.1-konforme Aufweckereignisse

• SMBIOS 2.3.1-Unterstützung

• CPU, DRAM, PCH 1,05 V / Mehrfachspannungsanpassung

Hardware-

überwachung

• CPU-/Gehäusetemperaturerkennung

• CPU/Gehäuse-Lüertachometer

• Lautloser CPU-/Gehäuselüer (ermöglicht automatische

Anpassung der Geschwindigkeit des Gehäuselüers über die

CPU-Temperatur)

• CPU/Gehäuselüer-Mehrfachgeschwindigkeitssteuerung

• Gehäuse-oen-Erkennung

• Spannungsüberwachung: +12 V, +5 V, +3,3 V, CPU Vcore

Betriebssy-

stem

• Microso® Windows® 8.1, 32 Bit / 8.1, 64 Bit / 8, 32 Bit / 8, 64

Bit / 7, 32 Bit / 7, 64 Bit

Zertizierun-

gen

• FCC, CE, WHQL

• ErP/EuP ready (ErP/EuP ready-Netzteil erforderlich)

* Detaillierte Produktinformationen nden Sie auf unserer Webseite: http://www.asrock.com

Deutsch

H81M-ITX/WiFi

Bitte beachten Sie, dass mit einer Übertaktung, zu der die Anpassung von BIOS-

Einstellungen, die Anwendung der Untied Overclocking Technology oder die

Nutzung von Übertaktungswerkzeugen von Drittanbietern zählen, bestimmte

Risiken verbunden sind. Eine Übertaktung kann sich auf die Stabilität Ihres Systems

auswirken und sogar Komponenten und Geräte Ihres Systems beschädigen. Sie sollte

auf eigene Gefahr und eigene Kosten durchgeführt werden. Wir übernehmen keine

Verantwortung für mögliche Schäden, die durch eine Übertaktung verursacht wurden.

Aufgrund von Beschränkungen kann die Größe des tatsächlich für die Systemnutzung

reservierten Speichers unter Windows®-Betriebssystemen mit 32 Bit weniger als

4 GB betragen. Windows®-Betriebssysteme mit 64 Bit haben keine derartigen

Beschränkungen. Mit ASRock XFast RAM können Sie den Speicher einsetzen, den

Windows® nicht nutzen kann.

Deutsch

1.3 Jumpereinstellung

Die Abbildung zeigt, wie die Jumper eingestellt werden. Wenn die Jumper-

Kappe auf den Kontakten angebracht ist, ist der Jumper „kurzgeschlossen“. Wenn

keine Jumper-Kappe auf den Kontakten angebracht ist, ist der Jumper „oen“.

Die Abbildung zeigt einen 3-poligen Jumper, dessen Kontakt 1 und Kontakt

2 „kurzgeschlossen“ sind, wenn eine Jumper-Kappe auf diesen 2 Kontakten

angebracht ist.

CMOS-löschen-Jumper

(CLRCMOS1)

(siehe S. 1, Nr. 4)

CLRCMOS1 ermöglicht Ihnen die Löschung der Daten im CMOS. Zum Löschen

und Rücksetzen der Systemparameter auf die Standardeinrichtung schalten Sie

den Computer bitte ab und ziehen das Netzkabel aus der Steckdose. Warten Sie 15

Sekunde, schließen Sie dann Kontakt 2 und Kontakt 3 an CLRCMOS1 5 Sekunden

lang mit einer Jumper-Kappe kurz. Löschen Sie den CMOS jedoch nicht direkt

nach der BIOS-Aktualisierung. Falls Sie den CMOS direkt nach Abschluss der

BIOS-Aktualisierung löschen müssen, starten Sie das System zunächst; fahren Sie

es dann vor der CMOS-Löschung herunter. Bitte beachten Sie, dass Kennwort,

Datum, Zeit und Benutzerstandardprol nur gelöscht werden, wenn die CMOS-

Batterie entfernt wird.

CMOS löschen

Standard

Falls Sie den CMOS löschen, wird möglicherweise ein Gehäuseeingri erkannt. Bitte

passen Sie die BIOS-Option „Status löschen“ zur Löschung der Aufzeichnung des

vorherigen Gehäuseeingristatus an.

Deutsch

H81M-ITX/WiFi

1.4 Integrierte Stiftleisten und Anschlüsse

Systemblende-Stileiste

(9-polig, PANEL1)

(siehe S. 1, Nr. 9)

Verbinden Sie

Netzschalter, Reset-Taste

und Systemstatusanzeige

am Gehäuse entsprechend

der nachstehenden

Pinbelegung mit dieser

Stileiste. Beachten Sie

vor Anschließen der

Kabel die positiven und

negativen Kontakte.

GND

RESET#

PWRBTN#

PLED-

PLED+

GND

HDLED-

HDLED+

GND

PWRBTN (Ein-/Austaste):

Mit der Ein-/Austaste an der Frontblende des Gehäuses verbinden. Sie können die

Abschaltung Ihres Systems über die Ein-/Austaste kongurieren.

RESET (Reset-Taste):

Mit der Reset-Taste an der Frontblende des Gehäuses verbinden. Starten Sie den

Computer über die Reset-Taste neu, wenn er abstürzt oder sich nicht normal neu

starten lässt.

PLED (Systembetrieb-LED):

Mit der Betriebsstatusanzeige an der Frontblende des Gehäuses verbinden. Die LED

leuchtet, wenn das System läu. Die LED blinkt, wenn sich das System im S1/S3-

Ruhezustand bendet. Die LED ist aus, wenn sich das System im S4-Ruhezustand

bendet oder ausgeschaltet ist (S5).

HDLED (Festplattenaktivität-LED):

Mit der Festplattenaktivität-LED an der Frontblende des Gehäuses verbinden. Die

LED leuchtet, wenn die Festplatte Daten liest oder schreibt.

Das Design der Frontblende kann je nach Gehäuse variieren. Ein Frontblendenmodul

besteht hauptsächlich aus Ein-/Austaste, Reset-Taste, Betrieb-LED,

Festplattenaktivität-LED, Lautsprecher etc. Stellen Sie beim Anschließen Ihres

Frontblendenmoduls an diese Stileiste sicher, dass Kabel- und Pinbelegung richtig

abgestimmt sind.

Integrierte Stileisten und Anschlüsse sind KEINE Jumper. Bringen Sie KEINE

Jumper-Kappen an diesen Stileisten und Anschlüssen an. Durch Anbringen von

Jumper-Kappen an diesen Stileisten und Anschlüssen können Sie das Motherboard

dauerha beschädigen.

Deutsch

Serial-ATA-II-Anschlüsse

(SATA_2:

siehe S. 1, Nr. 13)

(SATA_3:

siehe S. 1, Nr. 14)

Diese beiden SATA-II-

Anschlüsse unterstützen

SATA-Datenkabel für

interne Speichergeräte mit

einer Datenübertragungs-

geschwindigkeit bis 3,0

Gb/s.

Serial-ATA-III-

Anschlüsse

(SATA3_0:

siehe S. 1, Nr. 11)

(SATA3_1:

siehe S. 1, Nr. 12)

Diese beiden SATA-III-

Anschlüsse unterstützen

SATA-Datenkabel für

interne Speichergeräte mit

einer Datenübertragungs-

geschwindigkeit bis 6,0

Gb/s.

USB 2.0-Stileisten

(9-polig, USB_4_5)

(siehe S. 1, Nr. 10)

(9-polig, USB_6_7)

(siehe S. 1, Nr. 8)

Neben vier USB 2.0-Ports

an der E/A-Blende

benden sich zwei

Stileisten an diesem

Motherboard. Jede USB

2.0-Stileiste kann zwei

Ports unterstützen.

Audiostileiste

(Frontblende)

(9-polig, HD_AUDIO1)

(siehe S. 1, Nr. 15)

Diese Stileiste dient

dem Anschließen von

Audiogeräten an der

Frontblende.

J_SENSE

OUT2_L

MIC_RET

PRESENCE#

GND

OUT2_R

MIC2_R

MIC2_L

OUT_RET

SATA3_1

SATA3_0

SATA_3

SATA_2

DUMMY

GND GND

-B

-A

USB_PWR

Deutsch

H81M-ITX/WiFi

Gehäuse-

Lüeranschlüsse

(4-polig, CHA_FAN1)

(siehe S. 1, Nr. 16)

Bitte verbinden Sie die

Lüerkabel mit den

Lüeranschlüssen; der

schwarze Draht gehört

zum Erdungskontakt.

CPU-Lüeranschlüsse

(4-polig, CPU_FAN1)

(siehe S. 1, Nr. 1)

Dieses Motherboard bietet

einen 4-poligen CPU-

Lüeranschluss (lautloser

Lüer). Falls Sie einen

3-poligen CPU-Lüer

anschließen möchten,

verbinden Sie ihn bitte mit

Kontakt 1 bis 3.

ATX-Netzanschluss

(24-polig, ATXPWR1)

(siehe S. 1, Nr. 6)

Dieses Motherboard

bietet einen 24-poligen

ATX-Netzanschluss.

Bitte schließen Sie es zur

Nutzung eines 20-poligen

ATX-Netzteils entlang

Kontakt 1 und Kontakt 13

an.

1. High Denition Audio unterstützt Anschlusserkennung, der Draht am Gehäuse

muss dazu jedoch HDA unterstützt. Bitte befolgen Sie zum Installieren Ihres

Systems die Anweisungen in unserer Anleitung und der Anleitung zum Gehäuse.

2. Wenn Sie ein AC’97-Audiopanel nutzen, installieren Sie es bitte anhand der

nachstehenden Schritte an der Audiostileiste (Frontblende):

A. Verbinden Sie Mic_IN (MIC) mit MIC2_L.

B. Verbinden Sie Audio_R (RIN) mit OUT2_R und Audio_L (LIN) mit OUT2_L.

C. Verbinden Sie Erde (GND) mit Erde (GND).

D. MIC_RET und OUT_RET sind nur für das HD-Audio-Panel vorgesehen. Sie

müssen Sie nicht mit dem AC’97-Audiopanel verbinden.

E. Rufen Sie zur Aktivierung des vorderen Mikrofons das „FrontMic

(Frontmikrofon)“-Register in der Realtek-Systemsteuerung auf und passen

„Recording Volume (Aufnahmelautstärke)“ an.

FAN_SPEED

FAN_SPEED_CONTROL

+12V

GND

FAN_SPEED

FAN_SPEED_CONTROL

+12V

GND

Deutsch

ATX-12-V-Netzanschluss

(4-polig, ATX12V1)

(siehe S. 1, Nr. 2)

Bitte schließen Sie an

diesen Anschluss die ATX

12V Stromversorgung an.

Gehäuseeingri-

Stileiste

(2-polig, CI1)

(siehe S. 1, Nr. 5)

Dieses Motherboard unter-

stützt die Gehäuse-oen-

Erkennung, die erkennt,

wenn die Gehäuseabdek-

kung entfernt wurde. Diese

Funktion setzt ein Gehäuse

mit Gehäuseeingrierken-

nungsdesign voraus.

TPM-Stileiste

(17-polig, TPMS1)

(siehe S. 1, Nr. 7)

Dieser Anschluss

unterstützt das Trusted

Platform Module- (TPM)

System, das Schlüssel,

digitale Zertikate,

Kennwörter und Daten

sicher auewahren kann.

Ein TPM-System hil

zudem bei der Stärkung

der Netzwerksicherheit,

schützt digitale

Identitäten und

gewährleistet die

Plattformintegrität.

Signal

GND

SMB_DATA_MAIN

LAD2

LAD1

GND

S_PWRDWN#

SERIRQ#

GND

PCICLK

PCIRST#

LAD3

+3V

LAD0

+3VSB

GND

FRAME

SMB_CLK_MAIN

Français

H81M-ITX/WiFi

1 Introduction

Nous vous remercions d’avoir acheté cette carte mère ASRock H81M-ITX/WiFi,

une carte mère able fabriquée conformément au contrôle de qualité rigoureux et

constant appliqué par ASRock. Fidèle à son engagement de qualité et de durabilité,

ASRock vous garantit une carte mère de conception robuste aux performances

élevées.

1.1 Contenu de l’emballage

• Carte mère ASRock H81M-ITX/WiFi (facteur de forme Mini-ITX)

• Guide d’installation rapide ASRock H81M-ITX/WiFi

• CD d’assistance ASRock H81M-ITX/WiFi

• 1 x panneau de protection E/S

• 2 x câbles de données Serial ATA (SATA) (Optionnel)

• 1 x module Wi-Fi-802.11ac

• 1 x câble d’antenne SMA Wi-Fi

• 1 x antenne Wi-Fi 2,4 GHz ASRock

• 1 x crochet module WiFi

• 2 x vis pour module Wi-Fi

Les spécications de la carte mère et du logiciel BIOS pouvant être mises à jour,

le contenu de ce document est soumis à modication sans préavis. En cas de

modications du présent document, la version mise à jour sera disponible sur le site

Internet ASRock sans notication préalable. Si vous avez besoin d’une assistance

technique pour votre carte mère, veuillez visiter notre site Internet pour plus de

détails sur le modèle que vous utilisez. La liste la plus récente des cartes VGA et des

processeurs pris en charge est également disponible sur le site Internet de ASRock. Site

Internet ASRock http://www.asrock.com.

Français

1.2 Spécications

Plateforme

• Facteur de forme Mini-ITX

• Conception à condensateurs solides

• PCB High Density Glass Fabric

Processeur

• Prend en charge les processeurs Intel® Core

i7/i5/i3/Xeon®/

Pentium®/Celeron® 4e, nouvelle 4e génération (socket 1150)

• Prend en charge la technologie Intel® Turbo Boost 2.0

Chipset

• Intel® H81

Mémoire

• Technologie mémoire double canal DDR3

• 2 x fentes DIMM DDR3

• Prend en charge les mémoires sans tampon non ECC DDR3

1600/1333/1066

• Capacité max. de la mémoire système : 16Go

(voir AVERTISSEMENT)

• Prend en charge Intel® Extreme Memory Prole (XMP)1.3/1.2

Fente

d’expansion

• 1 x fente PCI Express 2.0 x 16

• 1 x demi-fente verticale mini-PCI Express pour module WiFi

Graphiques

• La technologie Intel® HD Graphics Built-in Visuals et les

sorties VGA sont uniquement prises en charge par les

processeurs intégrant un contrôleur graphique.

• Prend en charge la technologie Intel® HD Graphics Built-in

Visuals : Intel® Quick Sync Video with AVC, MVC (S3D) and

MPEG-2 Full HW Encode1, Intel® InTru

3D, Intel® Clear

Video HD Technology, Intel® Insider

, Intel® HD Graphics

4400/4600

• Pixel Shader 5.0, DirectX 11.1

• Mémoire partagée max. 1792Mo

• Trois options de sortie VGA : D-Sub, DVI-D et HDMI

• Prend en charge la conguration à triple moniteurs

• Prend en charge la technologie HDMI avec une résolution

maximale de 1920x1200 @ 60Hz

• Prend en charge le mode DVI-D avec une résolution

maximale de 1920x1200 @ 60Hz

• Prend en charge le mode D-Sub avec une résolution maximale

de 1920x1200 @ 60Hz

Français

H81M-ITX/WiFi

• Prend en charge les technologies Auto Lip Sync, Deep Color

(12bpc), xvYCC et HBR (High Bit Rate Audio) avec HDMI (un

écran compatible HDMI est requis)

• Prend en charge la fonction HDCP via ports DVI-D et HDMI

• Prend en charge la lecture Blu-ray (BD) Full HD 1080p via

ports DVI-D et HDMI

Audio

• Audio 5.1 CH HD (codec audio Realtek ALC662)

• Supporte la protection contre les surtensions (protection

complète contre surges ASRock)

• Capuchons ELNA Audio

Réseau

• PCIE x1 Gigabit LAN 10/100/1000 Mo/s

• Realtek RTL8111GR

• Supporte le réveil-sur-WAN

• Prend en charge la fonction Wake-On-LAN

• Supporte la protection contre la foudre/ESD (protection

complète contre surges ASRock)

• Prise en charge de la détection de câble LAN

• Prend en charge la fonction d’économie d’énergie Ethernet

802.3az

• Prend en charge PXE

Réseau sans-

l

Module WiFi-802.11n

• 1T1R 150Mbps IEEE 802.11n / 54Mbps IEEE 802.11g /

11Mbps IEEE 802.11b

• Prend en charge le mode Station (mode Infrastructure et

mode Ad-hoc)

Connectique

du panneau

arrière

• 1 x port souris/clavier PS/2

• 1 x port D-Sub

• 1 x port DVI-D

• 1 x port HDMI

• 4 x ports USB 2.0 (Supporte la protection ESD (protection

complète contre surges ASRock))

• 2 x ports USB 3.0 (Supporte la protection ESD (protection

complète contre surges ASRock))

• 1 x port RJ-45 LAN avec LED (LED ACT/LIEN et LED

VITESSE)

• Connecteurs jack audio HD : entrée ligne / haut-parleur avant

/ microphone

Français

Stockage

• 2 x connecteurs SATA3 6,0 Go/s, compatibles avec les

fonctions NCQ, AHCI et Hot Plug

• 2 x connecteurs SATA2 3,0 Go/s, compatibles avec les

fonctions NCQ, AHCI et Hot Plug

Connectique

• 1 x embase d’intrusion châssis

• 1 x embase TPM

• 1 x connecteur pour ventilateur de processeur (4 broches)

• 1 x connecteur pour ventilateur de châssis (4 broches)

• 1 x connecteur d’alimentation ATX 24 broches

• 1 x connecteur d’alimentation 12V 4 broches

• 1 x connecteur audio panneau frontal

• 2 x embases USB 2.0 (pour 4 ports USB 2.0) (Supporte la

protection ESD (protection complète contre surges ASRock))

BIOS

• BIOS UEFI AMI 32Mo avec prise en charge d’interface

graphique multilingue

• Compatible ACPI 1.1 Wake Up Events

• Prend en charge SMBIOS 2.3.1

• Réglage de la tension CPU, DRAM, PCH 1,05V

Surveillance

du matériel

• Détection de la température du processeur/châssis

• Tachéomètre processeur/châssis d’alimentation

• Fonction ventilateur silencieux processeur/châssis Quiet

Fan (permet au ventilateur du châssis d’adapter sa vitesse de

rotation automatiquement en fonction de la température du

processeur)

• Contrôle simultané des vitesse du ventilateur processeur/

châssis

• Détection CHASSIS OUVERT

• Surveillance de la tension d’alimentation : +12V, +5V, +3,3V,

CPU Vcore

Système

d’exploitation

• Microso® Windows® 8.1 32-bit / 8.1 64-bit / 8 32-bit / 8 64-

bit / 7 32-bit / 7 64-bit

Certications

• FCC, CE, WHQL

• ErP/EuP Ready (alimentation ErP/EuP ready requise)

* pour des informations détaillées de nos produits, veuillez visiter notre site:

http://www.asrock.com

Français

H81M-ITX/WiFi

Il est important de signaler que l'overcloking présente certains risques, incluant

des modications du BIOS, l’application d’une technologie d’overclocking déliée

et l'utilisation d'outils d'overclocking développés par des tiers. La stabilité de votre

système peut être aectée par ces pratiques, voire provoquer des dommages aux

composants et aux périphériques du système. L’overclocking se fait à vos risques et

périls. Nous ne pourrons en aucun cas être tenus pour responsables des dommages

éventuels provoqués par l’overclocking.

En raison de limitations dues au système d'exploitation, la capacité de mémoire

utilisée sous Windows® 32-bit peut être inférieure à 4 Go. Cette limitation ne

concerne pas les systèmes d'exploitation Windows® 64-bit. Vous pouvez utiliser

ASRock XFast RAM pour utiliser la mémoire dont Windows® ne peut se servir.

Français

1.3 Conguration des cavaliers (jumpers)

L’illustration ci-dessous vous renseigne sur la conguration des cavaliers (jumpers).

Lorsque le capuchon du cavalier est installé sur les broches, le cavalier est ‘court-

circuité’. Si le capuchon du cavalier n’est pas installé sur les broches, le cavalier est

‘ouvert’. L’illustration représente un cavalier à 3 broches dont les broches 1 et 2 sont

«court-circuitées» si un capuchon de cavalier est posé sur ces 2 broches.

Cavalier Clear CMOS

(CLRCMOS1)

(voir p.1, No. 4)

CLRCMOS1 vous permet d’eacer les donnés de la CMOS. Pour eacer les

paramètres du système et rétablir les valeurs par défaut, veuillez éteindre votre

ordinateur et débrancher son cordon d’alimentation. Patientez 15 secondes, puis

utilisez un capuchon de cavalier pour court-circuiter la broche 2 et la broche 3 sur

CLRCMOS1 pendant 5 secondes. Toutefois, n’eacez pas la CMOS immédiatement

après avoir mis à jour le BIOS. Si vous avez besoin d’eacer les données CMOS

après une mise à jour du BIOS, vous devez tout d’abord redémarrer le système,

puis l’éteindre avant de procéder à l’eacement de la CMOS. Veuillez noter que les

paramètres mot de passe, date, heure et prol de l’utilisateur seront uniquement

eacés en cas de retrait de la pile de la CMOS.

Fonction Clear CMOS

Par défaut

Si vous eacez la CMOS, l’alerte de châssis ouvert peut se déclencher. Veuillez régler

l’option du BIOS sur «Eacer » pour supprimer l’historique des intrusions de châssis

précédentes.

Français

H81M-ITX/WiFi

1.4 Embases et connecteurs de la carte mère

Embase du panneau

système

(PANNEAU1 à 9 broches)

(voir p.1, No. 9)

Branchez le bouton

de mise en marche, le

bouton de réinitialisation

et le témoin d’état du

système présents sur

le châssis sur cette

embase en respectant la

conguration des broches

illustrée ci-dessous.

Repérez les broches

positive et négative avant

de brancher les câbles.

GND

RESET#

PWRBTN#

PLED-

PLED+

GND

HDLED-

HDLED+

GND

PWRBTN (Bouton de mise en marche) :

pour brancher le bouton de mise en marche au panneau frontal du châssis. Vous

pouvez congurer la façon dont votre système doit s’arrêter à l’aide du bouton de

mise en marche.

RESET (Bouton de réinitialisation) :

pour brancher le bouton de réinitialisation au panneau frontal du châssis. Appuyez

sur le bouton de réinitialisation pour redémarrer l’ordinateur en cas de plantage ou

de dysfonctionnement au démarrage.

PLED (LED d’alimentation du système) :

pour brancher le témoin d’état de l’alimentation au panneau frontal du châssis. Le

LED est allumé lorsque le système fonctionne. Le LED clignote lorsque le système se

trouve en mode veille S1/S3. Le LED est éteint lorsque le système se trouve en mode

veille S4 ou hors tension (S5).

HDLED (LED d’activité du disque dur) :

pour brancher le témoin LED d’activité du disque dur au panneau frontal du

châssis. Le LED est allumé lorsque le disque dur lit ou écrit des données.

La conception du panneau frontal peut varier en fonction du châssis. Un module de

panneau frontal est principalement composé d'un bouton de mise en marche, bouton

de réinitialisation, LED d’alimentation, LED d’activité du disque dur, haut-parleur

etc. Lorsque vous reliez le module du panneau frontal de votre châssis sur cette

embase, veillez à parfaitement faire correspondre les ls et les broches.

Les embases et connecteurs situés sur la carte NE SONT PAS des cavaliers. Ne

placez JAMAIS de capuchons de cavaliers sur ces embases ou connecteurs. Placer un

capuchon de cavalier sur ces embases ou connecteurs endommagera irrémédiablement

votre carte mère.

Français

Connecteurs Serial ATA2

(SATA_2:

voir p.1, No. 13)

(SATA_3:

voir p.1, No. 14)

Ces deux connecteurs

SATA2 sont compatibles

avec les câbles de données

SATA pour les appareils

de stockage internes

avec un taux de transfert

maximal de 3,0 Go/s.

Connecteurs Serial ATA3

(SATA3_0:

voir p.1, No. 11)

(SATA3_1:

voir p.1, No. 12)

Ces deux connecteurs

SATA3 sont compatibles

avec les câbles de données

SATA pour les appareils

de stockage internes

avec un taux de transfert

maximal de 6,0 Go/s.

Embases USB 2.0

(USB_4_5 à 9 broches)

(voir p.1, No. 10)

(USB_6_7 à 9 broches)

(voir p.1, No. 8)

En plus des quatre ports

USB 2.0 sur le panneau

E/S, cette carte mère est

dotée de deux embases.

Chaque embase USB 2.0

peut prendre en charge

deux ports.

Embase audio du panneau

frontal

(HD_AUDIO1 à 9

broches)

(voir p.1, No. 15)

Cette embase sert au

branchement des appareils

audio au panneau audio

frontal.

J_SENSE

OUT2_L

MIC_RET

PRESENCE#

GND

OUT2_R

MIC2_R

MIC2_L

OUT_RET

SATA3_1

SATA3_0

SATA_3

SATA_2

DUMMY

GND GND

-B

-A

USB_PWR

Français

H81M-ITX/WiFi

Connecteurs du châssis

ventilateur

(CHA_FAN1 à 4 broches)

(voir p.1, No. 16)

Veuillez brancher les

câbles du ventilateur

sur les connecteurs du

ventilateur, puis reliez le

l noir à la broche de mise

à terre.

Connecteurs du

ventilateur du processeur

(CPU_FAN1 à 4 broches)

(voir p.1, No. 1)

Cette carte mère est dotée

d’un connecteur pour

ventilateur de processeur

(Quiet Fan) à 4 broches.

Si vous envisagez de

connecter un ventilateur

de processeur à 3 broches,

veuillez le brancher sur la

Broche 1-3.

Connecteur

d’alimentation ATX

(ATXPWR1 à 24 broches)

(voir p.1, No. 6)

Cette carte mère est

dotée d’un connecteur

d’alimentation ATX à 24

broches. Pour utiliser une

alimentation ATX à 20

broches, veuillez eectuer

les branchements sur la

Broche 1 et la Broche 13.

1. L’audio haute dénition prend en charge la technologie Jack Sensing (détection

de la che), mais le panneau grillagé du châssis doit être compatible avec la HDA

pour fonctionner correctement. Veuillez suivre les instructions gurant dans notre

manuel et dans le manuel du châssis pour installer votre système.

2. Si vous utilisez un panneau audio AC’97, veuillez le brancher sur l’embase audio du

panneau frontal en procédant comme suit :

A. branchez Mic_IN (MIC) sur MIC2_L.

B. branchez Audio_R (RIN) sur OUT2_R et Audio_L (LIN) sur OUT2_L.

C. branchez la mise à terre (GND) sur mise à terre (GND).

D. MIC_RET et OUT_RET sont exclusivement réservés au panneau audio HD. Il

est inutile de les brancher avec le panneau audio AC’97.

E. Pour activer le micro frontal, sélectionnez l’onglet « FrontMic » du panneau de

contrôle Realtek et réglez le paramètre « Volume d’enregistrement ».

FAN_SPEED

FAN_SPEED_CONTROL

+12V

GND

FAN_SPEED

FAN_SPEED_CONTROL

+12V

GND

Français

Connecteur

d’alimentation ATX 12V

(ATX12V1 à 4 broches)

(voir p.1, No. 2)

Veuillez connecter une

unité d’alimentation

électrique ATX 12V sur ce

connecteur.

Embase d’intrusion

châssis

(CI1 à 2 broches)

(voir p.1, No. 5)

Cette carte mère prend

en charge la fonction

de détection CHASSIS

OUVERT qui alerte

l’utilisateur en cas de

retrait du boîtier du

châssis. Cette fonction

requiert un châssis à

conception intégrant la

détection d’intrusion.

Embase TPM

(TPMS1 à 17 broches)

(voir p.1, No. 7)

Ce connecteur prend en

charge un module TPM

(Trusted Platform Module

– Module de plateforme

sécurisée), qui permet

de sauvegarder clés,

certicats numériques,

mots de passe et données

en toute sécurité. Le

système TPM permet

également de renforcer

la sécurité du réseau,

de protéger les identités

numériques et de

préserver l'intégrité de la

plateforme.

Signal

GND

SMB_DATA_MAIN

LAD2

LAD1

GND

S_PWRDWN#

SERIRQ#

GND

PCICLK

PCIRST#

LAD3

+3V

LAD0

+3VSB

GND

FRAME

SMB_CLK_MAIN

Italiano

H81M-ITX/WiFi

1 Introduzione

Grazie per aver acquistato la scheda madre H81M-ITX/WiFi ASRock, una scheda

madre adabile prodotta secondo i costanti e rigorosi controlli di qualità di

ASRock. La scheda madre ore eccellenti prestazioni con un design robusto che si

adatta all'impegno di ASRock di orire sempre qualità e durata.

1.1 Contenuto della confezione

• Scheda madre ASRock H81M-ITX/WiFi (Form Factor Mini-ITX)

• Guida all’installazione rapida di ASRock H81M-ITX/WiFi

• CD di supporto di ASRock H81M-ITX/WiFi

• 1 x mascherina metallica posteriore I/O

• 2 x cavi dati Serial ATA (SATA) (opzionali)

• 1 x modulo WiFi-802.11ac

• 1 x cavi antenna WiFi SMA

• 1 x antenne ASRock WiFi da 2,4 GHz

• 1 x staa per modulo WiFi

• 2 x viti per modulo WiFi

Dato che le speciche della scheda madre e del soware BIOS possono essere

aggiornate, il contenuto di questa documentazione sarà soggetto a variazioni senza

preavviso. Nel caso di eventuali modiche della presente documentazione, la versione

aggiornata sarà disponibile sul sito Web di ASRock senza ulteriore preavviso. Per

il supporto tecnico correlato a questa scheda madre, visitare il nostro sito Web per

informazioni speciche relative al modello attualmente in uso. È possibile trovare

l'elenco di schede VGA più recenti e di supporto di CPU anche sul sito Web di ASRock.

Sito Web di ASRock http://www.asrock.com.

Italiano

1.2 Speciche

Piattaforma

• Fattore di forma Mini-ITX

• Design di condensatore solido

• Circuito in vetro ad alta densità

CPU

• Supporta processori Intel® Core

i7/i5/i3/Xeon®/Pentium®/

Celeron® di nuova quarta e quarta generazione (Socket 1150)

• Supporta la tecnologia Intel® Turbo Boost 2.0

Chipset

• Intel® H81

Memoria

• Tecnologia con memoria DDR3 a doppio canale

• 2 x slot DIMM DDR3

• Supporta la memoria DDR3 1600/1333/1066 non ECC, senza

buer

• Capacità max. della memoria di sistema: 16GB

(si veda la sezione ATTENZIONE)

• Supporta Intel® Extreme Memory Prole (XMP)1.3/1.2

Slot di

espansione

• 1 x PCI Express 2.0 x16 slot

• 1 x alloggio di espansione verticale Half Mini-PCI Express:

Per il modulo WiFi

Graca

• La videograca integrata della scheda video HD Intel® e le

uscite VGA possono essere supportate soltanto con processori

con GPU integrata.

• Supporta la videograca integrata della scheda video HD

Intel®: Intel® Quick Sync Video con AVC, MVC (S3D) e

MPEG-2 Full HW Encode1, Intel® InTru

3D, tecnologia

Intel® Clear Video HD, Intel® Insider

, Intel® HD Graphics

4400/4600

• Pixel Shader 5.0, DirectX 11.1

• Memoria condivisa max. 1792 MB

• Tre opzioni uscita VGA: D-Sub, DVI-D e HDMI

• Supporta il triplo monitor

• Supporta la tecnologia HDMI con una risoluzione max. no a

1920 x 1200 a 60 Hz

• Supporta DVI-D con una risoluzione max. no a 1920 x 1200

a 60 Hz

• Supporta D-Sub con una risoluzione max. no a 1920 x 1200

a 60 Hz

Italiano

H81M-ITX/WiFi

• Supporta Auto Lip Sync, Deep Color (12 bpc), xvYCC e HBR

(High Bit Rate Audio) con HDMI (è necessario un monitor

conforme ad HDMI)

• Supporta la funzione HDCP con porte DVI-D e HDMI

• Supporta Blu-ray (BD) Full HD 1080p, riproduzione con

porte DVI-D e HDMI

Audio

• Audio HD a 5.1 canali (codec audio Realtek ALC662)

• Supporto protezione da sovratensione (protezione completa

ASRock dai picchi di corrente)

• Cappucci audio ELNA

LAN

• PCIE x 1 LAN Gigabit 10/100/1000 Mb/s

• Realtek RTL8111GR

• Supporto WOW (Wake-On-WAN)

• Supporta Wake-On-LAN

• Supporto la protezione da fulmini/scariche elettrostatiche

(ESD) (protezione completa ASRock dai picchi di corrente)

• Supporta il rilevamento cavo LAN

• Supporta Energy Ecient Ethernet 802.3az

• Supporta PXE

LAN wireless

Modulo WiFi-802.11n

• 1T1R 150Mbps IEEE 802.11n / 54Mbps IEEE 802.11g /

11Mbps IEEE 802.11b

• Supporta la modalità Stazione (infrastruttura e Ad-

I/O pannello

posteriore

• 1 x porta mouse/tastiera PS/2

• 1 x porta D-Sub

• 1 x porta DVI-D

• 1 x porta HDMI

• 4 x porte USB 2.0 (Supporto della protezione da scariche

elettrostatiche (ESD) (protezione completa ASRock dai picchi

di corrente))

• 2 x porte USB 3.0 (Supporto della protezione da scariche

elettrostatiche (ESD) (protezione completa ASRock dai picchi

di corrente))

• 1 x porta LAN RJ-45 con LED (ACT/LINK LED e SPEED

LED)

• Jack audio HD: ingresso linea/altoparlante anteriore/

microfono

Italiano

Archiviazione

• 2 x connettori SATA3 6,0 Gb/s, supporta le funzioni NCQ,

AHCI e “Hot Plug”

• 2 x connettori SATA2 3,0 Gb/s, supporta le funzioni NCQ,

AHCI e “Hot Plug”

Connettore

• 1 x header di intrusione nello chassis

• 1 x header TPM

• 1 x connettore ventola CPU (4 pin)

• 1 x connettore ventola chassis (4 pin))

• 1 x connettore alimentazione ATX a 24 pin

• 1 x connettore alimentazione da 12 V a 4 pin

• 1 x connettore audio pannello anteriore

• 2 x header USB 2.0 (supporto 4 porte USB 2.0) (Supporto

della protezione da scariche elettrostatiche (ESD) (protezione

completa ASRock dai picchi di corrente))

Caratteristi-

che del BIOS

• BIOS legale 32 Mb AMI UEFI con supporto GUI multilingue

• Eventi di wake up conformi ad ACPI 1.1

• Supporto SMBIOS 2.3.1

• Multiregolazione tensione CPU, DRAM, PCH 1,05 V

Hardware

Monitor

• Sensore temperatura CPU/chassis

• Tachimetro CPU/chassis alimentazione

• Ventola silenziosa CPU/chassis (consente l'autoregolazione

della velocità della ventola dello chassis mediante la

temperatura della CPU)

• Controllo multivelocità della ventola di CPU/chassis

• Rilevamento CASE OPEN

• Monitoraggio tensione: +12 V, +5 V, +3,3 V, CPU Vcore

• Microso® Windows® 8.1 32 bit / 8.1 64 bit / 8 32 bit / 8 64 bit

/ 7 32 bit / 7 64 bit

Certicazioni

• FCC, CE, WHQL

• ErP/EuP Ready (è necessaria alimentazione ErP/EuP ready)

* Per informazioni dettagliate sul prodotto, visitare il nostro sito Web: http://www.asrock.com

Italiano

H81M-ITX/WiFi

Prestare attenzione al potenziale rischio previsto nella pratica di overclocking, inclusa

la regolazione delle impostazioni nel BIOS, l'applicazione di tecnologia di Untied

Overclocking o l'utilizzo di strumenti di overclocking di terze parti. L'overclocking

può inuenzare la stabilità del sistema o perno provocare danni ai componenti e ai

dispositivi del sistema. Occorre eseguirlo a proprio rischio e spese. Non ci riterremo

responsabili per possibili danni provocati da overclocking.

A causa della limitazione, l'eettiva dimensione della memoria può essere inferiore

a 4 GB per riservare l'uso del sistema ai sistemi operativi di Windows® a 32 bit. I

sistemi operativi Windows® a 64 bit non possiedono tali limitazioni. È possibile

utilizzare la RAM XFast di ASRock per utilizzare la memoria che Windows® non può

utilizzare.

Italiano

1.3 Impostazione jumper

L'illustrazione mostra in che modo vengono impostati i jumper. Quando il

cappuccio del jumper è posizionato sui pin, il jumper è "cortocircuitato". Se sui pin

non è posizionato alcun cappuccio del jumper, il jumper è "aperto". L'illustrazione

mostra un jumper a 3 pin i cui pin1 e pin2 sono "cortocircuitati" quando un

cappuccio del jumper è posizionato su questi 2 pin.

Jumper per azzerare la

CMOS

(CLRCMOS1)

(vedere pag. 1, n. 4)

CLRCMOS1 consente di azzerare i dati presenti nella CMOS. Per azzerare e

reimpostare i parametri del sistema alla congurazione predenita, spegnere

il computer e scollegare il cavo di alimentazione dalla rete. Dopo aver atteso 15

secondi, utilizzare un cappuccio del jumper per cortocircuitare il pin2 e il pin3

su CLRCMOS1 per 5 secondi. Tuttavia, non azzerare la CMOS subito dopo aver

aggiornato il BIOS. Se è necessario azzerare la CMOS dopo l’aggiornamento del

BIOS, è necessario riavviare prima il sistema e in seguito spegnerlo prima di

eseguire l’operazione di azzeramento della CMOS. La password, la data, l’ora e il

prolo predenito dell’utente saranno azzerati solo se viene rimossa la batteria

della CMOS.

Azzerare la CMOS

predenito

Se si azzera la CMOS, può essere rilevato il case aperto. Regolare l'opzione del BIOS

"Azzerare stato" per azzerare il registro del precedente stato di intrusione nello chassis.

Italiano

H81M-ITX/WiFi

1.4 Header e connettori sulla scheda

Header sul pannello del

sistema

(PANEL1 a 9 pin)

(vedere pag. 1, n. 9)

Collegare l'interruttore

dell'alimentazione,

l'interruttore di reset e

l'indicatore dello stato

del sistema sullo chassis

su questo header secondo

la seguente assegnazione

dei pin. Annotare i pin

positivi e negativi prima

di collegare i cavi.

GND

RESET#

PWRBTN#

PLED-

PLED+

GND

HDLED-

HDLED+

GND

PWRBTN (interruttore alimentazione):

collegare all'interruttore dell'alimentazione sul pannello anteriore dello chassis. È

possibile congurare il modo in cui spegnere il sistema utilizzando l'interruttore

dell'alimentazione.

RESET (interruttore di reset):

collegare all'interruttore di reset sul pannello anteriore dello chassis. Premere

l'interruttore di reset per riavviare il computer se il computer si blocca e non riesce ad

eseguire un normale riavvio.

PLED (LED alimentazione del sistema):

collegare all'indicatore di stato dell'alimentazione sul pannello anteriore dello chassis.

Il LED è acceso quando il sistema è in funzione. Il LED continua a lampeggiare

quando il sistema si trova nello stato di sospensione S1/S3. Il LED è spento quando il

sistema si trova nello stato di sospensione S4 o quando è spento (S5).

HDLED (LED di attività disco rigido):

collegare al LED di attività disco rigido sul pannello anteriore dello chassis. Il LED è

acceso quando il disco rigido sta leggendo o scrivendo dati.

Il design del pannello anteriore può cambiare a seconda dello chassis. Un modulo

di pannello anteriore è composto principalmente da interruttore di alimentazione,

interruttore di reset, LED di alimentazione, LED di attività disco rigido, altoparlante,

ecc. Quando si collega il modulo del pannello anteriore dello chassis a questo

header, accertarsi che le assegnazioni del lo e le assegnazioni del pin corrispondano

correttamente.

Gli header e i connettori sulla scheda NON sono jumper. NON posizionare cappucci

del jumper su questi header e connettori. Il posizionamento di cappucci del jumper su

header e connettori provocherà danni permanenti alla scheda madre.

Italiano

Connettori Serial ATA2

(SATA_2:

vedere pag. 1, n. 13)

(SATA_3:

vedere pag. 1, n. 14)

Questi due connettori

SATA2 supportano i cavi

dati SATA per dispositivi

di archiviazione interna,

con una velocità di

trasferimento dati no a

3,0 Gb/s.

Connettori Serial ATA3

(SATA3_0:

vedere pag.1, n. 11)

(SATA3_1:

vedere pag. 1, n. 12)

Questi due connettori

SATA3 supportano cavi

dati SATA per dispositivi

di archiviazione interna,

con una velocità di

trasferimento dati no a 6,0

Gb/s.

Header USB 2.0

(USB_4_5 a 9 pin)

(vedere pag. 1, n. 10)

(USB_6_7 a 9 pin)

(vedere pag. 1, n. 8)

Oltre alle quattro porte

USB 2.0 sul pannello I/O,

su questa scheda madre

vi è due header. Ciascun

header USB 2.0 può

supportare due porte.

Header audio pannello

anteriore

(AUDIO1_HD a 9 pin)

(vedere pag. 1, n. 15)

Questo header serve a

collegare i dispositivi

audio al pannello audio

anteriore.

J_SENSE

OUT2_L

MIC_RET

PRESENCE#

GND

OUT2_R

MIC2_R

MIC2_L

OUT_RET

SATA3_1

SATA3_0

SATA_3

SATA_2

DUMMY

GND GND

-B

-A

USB_PWR

Italiano

H81M-ITX/WiFi

Connettori ventola dello

chassis

(CHA_FAN1 a 4 pin)

(vedere pag. 1, n. 16)

Collegare i cavi della

ventola ai connettori della

ventola e far corrispondere

il lo nero al pin di terra.

Connettori della ventola

della CPU

(CPU_FAN1 a 4 pin)

(vedere pag. 1, n. 1)

Questa scheda madre è

dotata di un connettore

per la ventola della CPU

(Ventola silenziosa) a

4 pin. Se si decide di

collegare una ventola della

CPU a 3 pin, collegarla al

pin 1-3.

Connettore di

alimentazione ATX

(ATXPWR1 a 24 pin)

(vedere pag. 1, n. 6)

Questa scheda madre è

dotata di un connettore

di alimentazione ATX

a 24 pin. Per utilizzare

un'alimentazione ATX a

20 pin, collegarla lungo il

pin1 e il pin 13.

1. L'audio ad alta denizione supporta le funzioni Jack sensing, ma il lo del pannello

sullo chassis deve supportare HDA per funzionare correttamente. Seguire le

istruzioni presenti nel nostro manuale e nel manuale dello chassis per installare il

sistema.

2. Se si utilizza un pannello audio AC’97, installarlo sull'header audio del pannello

anteriore seguendo le fasi di seguito:

A. Collegare Mic_IN (MIC) a MIC2_L.

B. Collegare Audio_R (RIN) a OUT2_R e Audio_L (LIN) a OUT2_L.

C. Collegare Ground (GND) a Ground (GND).

D. MIC_RET e OUT_RET servono soltanto per il pannello audio HD. Non è

necessario collegarli per il pannello audio AC’97.

E. Per attivare il microfono anteriore, andare alla scheda “MicAnt” nel pannello di

controllo Realtek e regolare il “Volume di registrazione”.

FAN_SPEED

FAN_SPEED_CONTROL

+12V

GND

FAN_SPEED

FAN_SPEED_CONTROL

+12V

GND

Italiano

Connettore di

alimentazione ATX da 12 V

(ATX12V1 a 4 pin)

(vedere pag. 1, n. 2)

Collegare un alimentatore

ATX 12 V a questo

connettore.

Header di intrusione nello

chassis

(CI1 a 2 pin)

(vedere pag. 1, n. 5)

Questa scheda madre

supporta la funzionalità di

rilevamento CASE OPEN

che rileva se il coperchio

dello chassis è stato

rimosso. Questa funzione

richiede uno chassis

con caratteristiche di

rilevamento di intrusione

nello chassis.

Header TPM

(TPMS1 a 17 pin)

(vedere pag. 1, n. 7)

Questo connettore

supporta il sistema

Trusted Platform Module

(TPM), che può archiviare

in modo sicuro chiavi,

certicati digitali,

password e dati. Un

sistema TPM permette

anche di potenziare la

sicurezza della rete, di

proteggere identità digitali

e di garantire l'integrità

della piattaforma.

Signal

GND

SMB_DATA_MAIN

LAD2

LAD1

GND

S_PWRDWN#

SERIRQ#

GND

PCICLK

PCIRST#

LAD3

+3V

LAD0

+3VSB

GND

FRAME

SMB_CLK_MAIN

Español

H81M-ITX/WiFi

1 Introducción

Gracias por comprar la placa base ASRock H81M-ITX/WiFi, una placa base

able fabricada según el rigurosísimo control de calidad de ASRock. Ofrece un

rendimiento excelente con un diseño resistente de acuerdo con el compromiso de

calidad y resistencia de ASRock.

1.1 Contenido del paquete

• Placa base ASRock H81M-ITX/WiFi (factor de forma Mini-ITX)

• Guía de instalación rápida de ASRock H81M-ITX/WiFi

• CD de soporte de ASRock H81M-ITX/WiFi

• 1 x escudo panel I/O

• 2 x cables de datos Serie ATA (SATA) (Opcional)

• 1 x Módulo WiFi-802.11ac

• 1 x Cables de antena WiFi SMA

• 1 x Antenas ASRock WiFi 2,4 GHz

• 1 x Soporte del módulo WiFi

• 2 x Tornillos para el módulo WiFi

Ya que las especicaciones de la placa base y el soware del BIOS podrán ser

actualizados, el contenido que aparece en esta documentación estará sujeto a

modicaciones sin previo aviso. Si esta documentación sufre alguna modicación,

la versión actualizada estará disponible en el sitio web de ASRock sin previo aviso.

Si necesita asistencia técnica relacionada con esta placa base, visite nuestro sitio

web para obtener información especíca sobre el modelo que esté utilizando. Podrá

encontrar las últimas tarjetas VGA, así como la lista de compatibilidad de la CPU, en

el sitio web de ASRock. Sitio web de ASRock http://www.asrock.com.

Español

1.2 Especicaciones

Plataforma

• Factor de forma Mini-ITX

• Diseño de los Condensadores: Solid

• PCB de bra de vidrio de alta densidad

CPU

• Admite procesadores Intel® Core

i7/i5/i3/Xeon®/Pentium®/

Celeron® (zócalo 1150) de la nueva 4ª y 4ª generación

• Compatible con la Tecnología de Intel® Turbo Boost 2.0

Conjunto de

chips

• Intel® H81

Memoria

• Tecnología de memoria de Doble Canal DDR3

• 2 ranuras DDR3 DIMM

• Compatible con memoria no-ECC, sin búfer DDR3

1600/1333/1066

• Capacidad máxima de la memoria del sistema: 16GB

(consulte la ADVERTENCIA)

• Compatible con Extreme Memory Prole (XMP)1.3/1.2 de

Intel®

Ranura de

expansión

• 1 ranura PCI Express 2.0 x16

• 1 x Ranura vertical media Mini-PCI Express: Para WiFi +

módulo

Grácos

• La Tecnología visual integrada de grácos HD de Intel® y las

salidas de VGA son compatibles únicamente con

procesadores con GPU integrado.

• Compatible con la Tecnología visual integrada de grácos

HD de Intel®: Intel® Quick Sync Video con AVC, MVC (S3D)

y MPEG-2 Full HW Encode1, Intel® InTru

3D, Intel® Clear

Video HD Technology, Intel® Insider

, Intel® HD Graphics

4400/4600

• Pixel Shader 5.0, DirectX 11.1

• Memoria compartida máxima: 1792MB

• Tres opciones de salida VGA: D-Sub, DVI-D y HDMI

• Compatible con monitores triples

• Compatible con Tecnología HDMI con máxima resolución

hasta 1920x1200 @ 60Hz

• Compatible con DVI-D con máxima resolución hasta

1920x1200 @ 60Hz

Español

H81M-ITX/WiFi

• Compatible con D-Sub con máxima resolución hasta

1920x1200 @ 60Hz

• Compatible con Auto Lip Sync, Deep Color (12bpc), xvYCC y

HBR (audio de alta velocidad de bits) con HDMI (requiere un

monitor compatible con HDMI)

• Compatible con función HDCP con puertos DVI-D y HDMI

• Compatible con reproducción Blu-ray (BD) Full HD de 1080p

con puertos DVI-D y HDMI

Audio

• 5.1 Audio CH HD (Realtek ALC662 Audio Codec)

• Admite protección contra subidas de tensión (Protección

Integral contra Picos de ASRock)

• Tapas de audio ELNA

LAN

• LAN Gigabit PCIE x1 10/100/1000 Mb/s

• Realtek RTL8111GR

• Admite Reactivación en WAN

• Compatible con Wake-On-LAN

• Admite protección contra rayos/ESD (Protección Integral

contra Picos de ASRock)

• Admite detección de conexión de cable LAN

• Compatible con Ethernet de consumo eciente de energía

802.3az

• Compatible con PXE

LAN

inalámbrica

Módulo WiFi-802.11n

• 1T1R 150 Mbps IEEE 802.11n / 54 Mbps IEEE 802.11g / 11

Mbps IEEE 802.11b

• Admite el modo de estación (modo Infraestructura y mod

Ad-hoc)

Panel trasero

I/O

• 1 puerto de ratón/teclado PS/2

• 1 puerto D-Sub

• 1 puerto DVI-D

• 1 puerto HDMI

• 4 puertos USB 2.0 (Admite protección ESD (Protección

Integral contra Picos de ASRock))

• 2 puertos USB 3.0 (Admite protección ESD (Protección

Integral contra Picos de ASRock))

• 1 puerto LAN RJ-45 con LED (ACT/LINK LED y SPEED

LED)

• Conector de audio HD: Entrada de línea / Altavoz frontal /

Micrófono

Español

Almace-

namiento

• 2 conectores SATA3 de 6,0 Gb/s, compatibles con las

funciones NCQ, AHCI y Hot Plug

• 2 conectores SATA2 de 3,0 Gb/s, compatibles con las

funciones NCQ, AHCI y Hot Plug

Conectores

• 1 cabezal de intrusión de chasis

• 1 cabezal TPM

• 1 conector de ventilador de la CPU (de 4 pines)

• 1 conector de ventilador del chasis (de 4 pines)

• 1 conector de alimentación ATX de 24 pines

• 1 conector de alimentación de 12V de 4 pines

• 1 conector de audio del panel frontal

• 2 cabezales USB 2.0 (compatibles con 4 puertos USB 2.0)

(Admite protección ESD (Protección Integral contra Picos de

ASRock))

Característi-

cas del BIOS

• BIOS legal UEFI AMI de 32Mb compatible con interfaz

gráca de usuario multilingüe

• Eventos de reactivación conformes con ACPI 1.1

• Compatible con SMBIOS 2.3.1

• Multiajuste de voltaje de CPU, DRAM, PCH 1,05V

Monitor del

hardware

• Método de sensor de temperatura de la CPU/Chasis

• Tacómetro del ventilador de CPU/Chasis

• Ventilador silencioso de la CPU/Chasis (permite ajustar

automáticamente la velocidad del ventilador del chasis

mediante la temperatura de la CPU)

• Control multivelocidad del ventilador de la CPU/Chasis

• Detección de CUBIERTA ABIERTA

• Control del voltaje: +12V, +5V, +3,3V, CPU Vcore

• Microso® Windows® 8.1 32 bits / 8.1 64 bits / 8 32 bits / 8 64

bits / 7 32 bits / 7 64 bits

Certicaciones

• FCC, CE, WHQL

• Compatible con ErP/EuP (requiere toma de alimentación

compatible con ErP/EuP)

* Para obtener más información acerca del producto, visite nuestro sitio web: http://www.asrock.com

Español

H81M-ITX/WiFi

Tenga en cuenta que existen ciertos riesgos relacionados con el overclocking

(sobreaceleración), incluyendo el ajuste de la conguración del BIOS, aplicando la

Tecnología overcloking no vinculada o utilizando las herramientas de overclocking

de tercera parte. El overclocking podría afectar la estabilidad de su sistema o incluso

dañar los componentes y dispositivos de su sistema. Si lo realiza, todos los riesgos y

gastos derivados del overclocking serán de su entera responsabilidad. No nos hacemos

responsables de posibles daños producidos por el overclocking.

Debido a las limitaciones, el tamaño real de la memoria podrá ser inferior a 4GB

para reservar espacio para el uso del sistema en sistemas operativos Windows® de

32 bits. Los sitemas operativos Windows® de 64 bits no tienen estas limitaciones.

Podrá utilizar XFast RAM de ASRock para usar la memoria que Windows® no puede

utilizar.

Español

1.3 Instalación de los puentes

La instalación muestra cómo deben instalarse los puentes. Cuando la tapa de puente

se coloca en los pines, el puente queda “Corto”. Si no coloca la tapa de puente en los

pines, el puente queda “Abierto”. La ilustración muestra un puente de 3 pines cuyo

pin 1 y pin 2 son “Cortos” cuando se coloca una tapa de puente en estos 2 pines.

Puente de borrado de

CMOS

(CLRCMOS1)

(consulte la pág.1, N.º 4)

CLRCMOS1 le permite borrar los datos del CMOS. Para borrar y restablecer los

parámetros del sistema a los valores predeterminados de instalación, apague el

ordenador y desenchufe el cable de alimentación de la toma de alimentación.

Después de esperar 15 segundos, utilice un tapa de puente para acortar el pin2 y

el pin3 en el CLRCMOS1 durante 5 segundos. Sin embargo, no borre el CMOS

justo después de que haya actualizado el BIOS. Si necesita borrar el CMOS cuando

acabe de actualizar el BIOS, deberá arrancar el sistema primero y, a continuación,

deberá apagarlo antes de que realice el borrado del CMOS. Tenga en cuenta

que la contraseña, la fecha, la hora y el perl de usuario predeterminado serán

eliminados únicamente si se retira la pila del CMOS.

Borrado de CMOS

Predeterminado

Si borra el CMOS, podrá detectarse la cubierta abierta. Ajuste la opción del BIOS “Clear

Status” (Borrar estado) para borrar el registro del estado de intrusión anterior del

chasis.

Español

H81M-ITX/WiFi

1.4 Conectores y cabezales incorporados

Cabezal del panel del

sistema

(PANEL1 de 9 pines)

(consulte la pág.1, N.º 9)

Conecte el interruptor de

alimentación, restablezca

el interruptor y el

indicador del estado del

sistema del chasis a los

valores de este cabezal,

según los valores

asignados a los pines

como se indica a

continuación. Cerciórese

de cuáles son los pines

positivos y los negativos

antes de conectar los

cables.

PWRBTN (Interruptor de alimentación):

conéctelo al interruptor de alimentación del panel frontal del chasis. Deberá

congurar la forma en la que su sistema se apagará mediante el interruptor de

alimentación.

RESET (Interruptor de reseteo):

conéctelo al interruptor de reseteo del panel frontal del chasis. Pulse el interruptor

de reseteo para resetear el ordenador si éste está bloqueado y no se puede reiniciar de

forma normal.

PLED (Indicador LED de alimentación del sistema):

conéctelo al indicador del estado de la alimentación del panel frontal del chasis.

El indicador LED permanece encendido cuando el sistema está funcionando. El

indicador LED parpadea cuando el sistema se encuentra en estado de suspensión S1/

S3. El indicador LED se apaga cuando el sistema se encuentra en estado de suspensión

S4 o está apagado (S5).

HDLED (Indicador LED de actividad en el disco duro):

conéctelo al indicador LED de actividad en el disco duro del panel frontal del

chasis. El indicador LED permanece encendido cuando el disco duro está leyendo o

escribiendo datos.

El diseño del panel frontal puede ser diferente dependiendo del chasis. Un módulo de

panel frontal consta principalmente de: interruptor de alimentación, interruptor de

reseteo, indicador LED de alimentación, indicador LED de actividad en el disco duro,

altavoz, etc. Cuando conecte su módulo del panel frontal del chasis a este cabezal,

asegúrese de que las asignaciones de los cables y los pines coinciden correctamente.

Los cabezales y conectores incorporados NO son puentes. NO coloque tapas de puente

sobre estos cabezales y conectores. Si coloca tapas de puente sobre los cabezales y

conectores dañará de forma permanente la placa base.

GND

RESET#

PWRBTN#

PLED-

PLED+

GND

HDLED-

HDLED+

GND

Español

Conectores Serie ATA2

(SATA_2:

consulte la pág.1, N.º 13)

(SATA_3:

consulte la pág.1, N.º 14)

Estos dos conectores

SATA2 son compatibles

con cables de datos SATA

para dispositivos de

almacenamiento interno

con una velocidad de

transferencia de datos de

hasta 3,0 Gb/s.

Conectores Serie ATA3

(SATA3_0:

consulte la pág.1, N.º 11)

(SATA3_1:

consulte la pág.1, N.º 12)

Estos dos conectores

SATA3 son compatibles

con cables de datos SATA

para dispositivos de

almacenamiento interno

con una velocidad de

transferencia de datos de

hasta 6,0 Gb/s.

Cabezales USB 2.0

(USB_4_5 de 9 pines)

(consulte la pág.1, N.º 10)

(USB_6_7 de 9 pines)

(consulte la pág.1, N.º 8)

Además de cuatro puertos

USB 2.0 en el panel I/O,

esta placa base contiene

dos cabezales. Cada

cabezal USB 2.0 admite

dos puertos.

Cabezal de audio del

panel frontal

(HD_AUDIO1 de 9 pines)

(consulte la pág.1, N.º 15)

Este cabezal se utiliza

para conectar dispositivos

de audio al panel de audio

frontal.

J_SENSE

OUT2_L

MIC_RET

PRESENCE#

GND

OUT2_R

MIC2_R

MIC2_L

OUT_RET

SATA3_1

SATA3_0

SATA_3

SATA_2

DUMMY

GND GND

-B

-A

USB_PWR

Español

H81M-ITX/WiFi

Conectores del ventilador

del chasis

(CHA_FAN1 de 4 pines)

(consulte la pág.1, N.º 16)

Conecte los cables del

ventilador a los conectores

del ventilador y haga

coincidir el cable negro

con el pin de conexión a

tierra.

Conectores del ventilador

de la CPU

(CPU_FAN1 de 4 pines)

(consulte la pág.1, N.º 1)

Esta placa base contiene

un conector de ventilador

(ventilador silencioso) de

CPU de 4 pines. Si tiene

pensando conectar un

ventilador de CPU de 3

pines, conéctelo al Pin 1-3.

Conector de alimentación

ATX

(ATXPWR1 de 24 pines)

(consulte la pág.1, N.º 6)

Esta placa base contiene

un conector de

alimentación ATX de 24

pines. Para utilizar una

toma de alimentación

ATX de 20 pines,

conéctela en los Pines del

1 al 13.

1. El Audio de Alta Denición (HDA, en inglés) es compatible con el método de sensor

de conectores, sin embargo, el cable del panel del chasis deberá ser compatible con

HDA para que pueda funcionar correctamente. Siga las instrucciones que se indican

en nuestro manual y en el manual del chasis para instalar su sistema.

2. Si utiliza un panel de audio AC’97, instálelo en el cabezal de audio del panel frontal

siguiendo los siguientes pasos:

A. Conecte Mic_IN (MIC) a MIC2_L.

B. Conecte Audio_R (RIN) a OUT2_R y Audio_L (LIN) a OUT2_L.

C. Conecte Ground (conexión a tierra) (GND) a Ground (GND).

D. MIC_RET y OUT_RET se utilizan únicamente para el panel de audio HD. No es

necesario que los conecte en el panel de audio AC’97.

E. Para activar el micrófono frontal, vaya a la cha “micrófono frontal” (FrontMic)

en el panel de control de Realtek y ajuste el “Volumen de grabación” (Recording

Volume).

FAN_SPEED

FAN_SPEED_CONTROL

+12V

GND

FAN_SPEED

FAN_SPEED_CONTROL

+12V

GND

Español

Conector de alimentación

ATX de 12V

(ATX12V1 de 4 pines)

(consulte la pág.1, N.º 2)

Conecte la fuente de

alimentación ATX 12V a

su cabezal.

Cabezal de intrusión de

chasis

(CI1 de 2 pines)

(consulte la pág.1, N.º 5)

Esta placa base es

compatible con la

función de detección de

CUBIERTA ABIERTA que

detecta si se ha retirado la

cubierta del chasis. Esta

función requiere un chasis

diseñado para la detección

de intrusión del chasis.

Cabezal TPM

(TPMS1 de 17 pines)

(consulte la pág.1, N.º 7)

Este conector es

compatible con el sistema

Módulo de Plataforma

Segura (TPM, en inglés),

que puede almacenar

de forma segura claves,

certicados digitales,

contraseñas y datos. Un

sistema TPM también

ayuda a aumentar la

seguridad en la red,

protege identidades

digitales y garantiza

la integridad de la

plataforma.

Signal

GND

SMB_DATA_MAIN

LAD2

LAD1

GND

S_PWRDWN#

SERIRQ#

GND

PCICLK

PCIRST#

LAD3

+3V

LAD0

+3VSB

GND

FRAME

SMB_CLK_MAIN



H81M-ITX/WiFi

1 

       ASRock

H81M-ITX/WiFi,     

 ASRock.     

      

   ASRock     .

1.1  

•   ASRock H81M-ITX/WiFi (- Mini-ITX)

•      ASRock H81M-ITX/WiFi

• -     ASRock H81M-ITX/WiFi

• 1      -

• 2     Serial ATA (SATA) ( )

• 1   WiFi-802.11ac

• 1   SMA  WiFi-

• 1 x ASRock WiFi- 2,4 

• 1    WiFi

• 2 x    WiFi

       

  BIOS   

     .  

       

 - ASRock   .  

 ,    , 

-         

 .  - ASRock    

   VGA-  . - ASRock http://

www.asrock.com.



1.2 



• - Mini-ITX

•   

• High Density Glass Fabric PCB



•    4-  4- 

Intel® Core

i7/i5/i3/Xeon®/Pentium®/Celeron® ( 1150)

•   Intel® Turbo Boost 2.0



• Intel® H81



•   DDR3

• 2   DDR3 DIMM

•    DDR3 1600/1333/1066 Non-

ECC Unbuered

•    : 16 

(. «»)

•  Intel® Extreme Memory Prole (XMP)1.3/1.2





• 1 x PCI Express 2.0 x16 

• 1 x   Half Mini-PCI Express: 

 WiFi





•    Intel® HD Graphics Built-

in Visuals  VGA    

   

.

•  Intel® HD Graphics Built-in Visuals: Intel® Quick

Sync Video  AVC, MVC (S3D)  MPEG-2 Full HW Encode1,

Intel® InTru

3D, Intel® Clear Video HD Technology, Intel®

Insider

, Intel® HD Graphics 4400/4600

• Pixel Shader 5.0, DirectX 11.1

•     :

1792 

•   VGA: D-Sub, DVI-D  HDMI

•     

•   HDMI  

  1920x1200  60 

•  DVI-D    

1920x1200  60 

•  D-Sub    

1920x1200  60 



H81M-ITX/WiFi

•  Auto Lip Sync, Deep Color (12bpc), xvYCC 

HBR (High Bit Rate Audio)  HDMI ( HDMI-

 )

•   HDCP   DVI-I  HDMI

•   Full HD 1080p Blu-ray (BD)

  DVI-D  HDMI



• 5.1 CH HD  HD (-  Realtek

ALC662)

•     ( 

(ASRock   ))

•    ELNA



• PCIE x1 Gigabit LAN 10/100/1000 /

• Realtek RTL8111GR

•  Wake-On-WAN

•  Wake-On-LAN

•    /

 (  (ASRock  

))

•    

•  Energy Ecient Ethernet 802.3az

•  PXE

-

 

 WiFi-802.11n

• 1T1R 150 /   IEEE 802.11n, 54 / 

 IEEE 802.11g, 11M /   IEEE 802.11b

•    ( 

  )



-



 



• 1 x PS/2  /

• 1 x D-Sub

• 1 x DVI-D

• 1 x HDMI

• 4 x USB 2.0 (   

 (  (ASRock  

))

• 2 x USB 3.0 (   

 (  (ASRock  

))

• 1 x RJ-45     ( ACT/LINK   SPEED)

•  HD Audio:   /  

/ 







• 2 x  SATA3 6,0 /,   NCQ,

AHCI   

• 2 x  SATA2 3,0 /,   NCQ,

AHCI   



• 1 x     

• 1 x  

• 1 x     (4-)

• 1 x     (4-)

• 1     (24-)

• 1 x 4-   12 

• 1 x    

• 2 x  USB 2.0 ( 4  USB

2.0) (   

 (  (ASRock  

))



BIOS

• 32  AMI UEFI Legal BIOS   



•     

ACPI 1.1

•  SMBIOS 2.3.1

•   , DRAM, PCH 1,05 





•   /

•   / 

•   /

(    

 )

•    /

•    

•  : +12 , +5 , +3,3 ,  Vcore



• Microso® Windows® 8.1 32-bit / 8.1 64-bit / 8 32-bit / 8 64-

bit / 7 32-bit / 7 64-bit



• FCC, CE, WHQL

•   ErP/EuP (  ,

  ErP/EuP)

*         -:

http://www.asrock.com



H81M-ITX/WiFi

 ,   ,   

BIOS,   Untied Overclocking Technology  

   ,  

 .      

         . 

          .  

    ,   .

       32-  Windows®

      4 .  64-

 Windows®   .    ,

  Windows®   ,  ASRock XFast

RAM.



1.3  

    .   

    «».   

   ,  «».   

3-     1  2   

  .

 

 CMOS

(CLRCMOS1)

(. . 1,  4)

CLRCMOS1     CMOS.  

       , 

        .

 15      2  3  CLRCMOS1

 5 .    CMOS    BIOS.

    CMOS   

BIOS   ,     

  CMOS. ,  , ,   

       , 

  CMOS.

  CMOS 

  CMOS      .

      ,

  Clear Status ( ) BIOS.



H81M-ITX/WiFi

1.4   ,   



 



(9-, PANEL1)

(. . 1,  9)



 

 

, 

 

 

   

  



,

 .

 

 



 

.

PWRBTN ( ):

  ,     .

       

.

RESET ( ):

   ,    

.   ,   ,

      .

PLED (   ):

  ,    

.   ,   . 

     S1/S3,  . 

     S4   (S5),  

.

HDLED (    ):

     ,

    .   ,

       .

       .   

     ,  , 

 ,     ,

  . .        

   .

       

 .        

.        

     .

GND

RESET#

PWRBTN#

PLED-

PLED+

GND

HDLED-

HDLED+

GND



 Serial ATA2

(SATA_2:

. . 1,  13)

(SATA_3:

. . 1,  14)

   SATA2

 

 

SATA 



  

   

3,0 /.

 Serial ATA3

(SATA3_0:

. .1,  11)

(SATA3_1:

. . 1,  12)

   SATA3

 

 

SATA 



  

   

6,0 /.

 USB 2.0.

(9-,

USB_4_5)

(. . 1,  10)

(9-,

USB_6_7)

(. . 1,  8)

  

USB 2.0   -

  

   

. 

 USB 2.0 

 

.

 



(9-, HD_

AUDIO1)

(. . 1,  15)

 



 

 

 .

J_SENSE

OUT2_L

MIC_RET

PRESENCE#

GND

OUT2_R

MIC2_R

MIC2_L

OUT_RET

SATA3_1

SATA3_0

SATA_3

SATA_2

DUMMY

GND GND

-B

-A

USB_PWR



H81M-ITX/WiFi

 

 

(4-, CHA_

FAN1)

(. . 1,  16)

 

 

 

  

  .

 



(4-, CPU_

FAN1)

(. . 1,  1)

 

 

4- 

 

 .  

 

3-

 ,

  

 1-3.

  

(24-,

ATXPWR1)

(. . 1,  6)

  

 24-

  .

 

20-

  ATX,

  

 1   13.

1.      

,      ,   

    HDA.   

 .       .

2.    AC’97    

 ,   :

A.  Mic_IN (MIC)  MIC2_L.

B.  Audio_R (RIN)  OUT2_R, Audio_L (LIN)  OUT2_L.

C.    (GND)    (GND).

D.  MIC_RET  OUT_RET    

 .    AC’97  

 .

E.    ,    FrontMic

  Realtek    Recording Volume

( ).

FAN_SPEED

FAN_SPEED_CONTROL

+12V

GND

FAN_SPEED

FAN_SPEED_CONTROL

+12V

GND



   12 

(4-,

ATX12V1)

(. . 1,  2)

  

  

ATX 12V.

  

 

(2-, CI1)

(. . 1,  5)

 

 



 

  

  .

  

  

 

.

 

(17-, TPMS1)

(. . 1,  7)

 



 

Trusted Platform

Module (TPM), 

 

 

, 

,

  .

  

 

 ,

 



 



.

Signal

GND

SMB_DATA_MAIN

LAD2

LAD1

GND

S_PWRDWN#

SERIRQ#

GND

PCICLK

PCIRST#

LAD3

+3V

LAD0

+3VSB

GND

FRAME

SMB_CLK_MAIN

Português

H81M-ITX/WiFi

1 Introdução

Obrigado por ter comprado a placa principal ASRock H81M-ITX/WiFi, uma placa

principal ável produzida sob os rigorosos critérios de controlo de qualidade da

ASRock. Esta placa principal oferece um excelente desempenho com um design

robusto em conformidade com o compromisso da ASRock em fabricar produtos de

qualidade e resistentes.

1.1 Conteúdo da embalagem

• Placa-mãe ASRock H81M-ITX/WiFi (Fator Mini-ITX Form)

• Guia de Instalação Rápida ASRock H81M-ITX/WiFi

• CD de Suporte da ASRock H81M-ITX/WiFi

• 1 x Painel de E/S

• 2 x Cabos de dados Serial ATA (SATA) (Opcional)

• 1 x Módulo WiFi-802.11ac

• 1 x Cabos de Antena SMA WiFi

• 1 x Antenas de 2,4 GHz da ASRock WiFi

• 1 x Suporte do Módulo WiFi

• 2 x Parafusos para Módulo WiFi

Dado que as especicações da placa principal e o soware do BIOS poderão ser

actualizados, o conteúdo desta documentação estará sujeito a alterações sem aviso

prévio. Caso ocorram modicações a esta documentação, a versão actualizada estará

disponível no Web site da ASRock sem aviso prévio. Se necessitar de assistência técnica

relacionada com esta placa principal, visite o nosso Web site para obter informações

especícas acerca do modelo que está a utilizar. Também poderá encontrar a lista

de placas VGA e CPU mais recentes suportadas no Web site da ASRock. Web site da

ASRock http://www.asrock.com.

Português

1.2 Especicações

Plataforma

• Formato Mini-ITX

• Design de condensador sólido

• PCB de Fibra de Vidro de Alta Densidade

CPU

• Suporta Processadores de 4ª Geração Nova e 4ª Geração Intel®

Core

i7/i5/i3/Xeon®/Pentium®/Celeron® (Soquete 1150)

• Suporta a tecnologia Intel® Turbo Boost 2.0

Chipset

• Intel® H81

Memória

• Tecnologia de memória DDR3 de dois canais

• 2 x ranhuras DIMM DDR3

• Suporta memória DDR3 1600/1333/1066, não ECC, sem

memória intermédia

• Capacidade máxima da memória do sistema: 16GB

(consultar AVISO)

• Suporta Extreme Memory Prole (XMP)1.3/1.2 da Intel®

Ranhuras de

expansão

• 1 x ranhura PCI Express 2.0 x16

• 1 x Slot Vertical Meio Mini-PCI Express: Para módulo WiFi

Grácos

• Os grácos incorporados Intel® HD e as saídas VGA

apenas podem ser suportados com processadores com GPU

integrada.

• Suporta grácos incorporados Intel® HD: Intel® Quick Sync

Video com AVC, MVC (S3D) e MPEG-2 Full HW Encode1,

Intel® InTru

3D, Tecnologia Intel® Clear Video HD, Intel®

Insider

, Grácos Intel® HD 4400/4600

• Pixel Shader 5.0, DirectX 11.1

• Memória partilhada máxima de 1792MB

• Três opções de saída VGA: D-Sub, DVI-D e HDMI

• Suporta conguração com três monitores

• Suporta tecnologia HDMI com resolução máxima de até

1920x1200 @ 60Hz

• Suporta DVI-D com resolução máxima de até 1920x1200 @

60Hz

• Suporta D-Sub com resolução máxima de até 1920x1200 @

60Hz

Português

H81M-ITX/WiFi

• Suporta Auto sincronização labial, Deep Color (12bpc),

xvYCC e HBR (High Bit Rate Audio) com HDMI (É

necessário um monitor compatível com HDMI)

• Suporta a função HDCP com portas DVI-D e HDMI

• Suporta reprodução Blu-ray (BD) Full HD a 1080p com

portas DVI-D e HDMI

Áudio

• Áudio HD de 5.1 canais (Codec de áudio Realtek ALC662)

• Suporta Proteção Contra Surto (Proteção Total contra Picos

ASRock)

• Fones de Áudio ELNA

LAN

• LAN Gigabit 10/100/1000 Mb/s PCIE x1

• Realtek RTL8111GR

• Suporta Wake-On-WAN

• Suporta Wake-On-LAN

• Suporta Proteção contta Relâmpago/ESD (Proteção Total

contra Picos ASRock)

• Suporta Detecção de cabo LAN

• Suporta IEEE 802.3az

• Suporta PXE

LAN sem os

Módulo WiFi-802.11n

• 1T1R 150Mbps IEEE 802.11n / 54Mbps IEEE 802.11g /

11Mbps IEEE 802.11b

• Suporta o modo de Estação (Modo de infra-estrutura e modo

Ad-hoc)

E/S do painel

traseiro

• 1 x Porta PS/2 para mouse/teclado

• 1 x Porta D-Sub

• 1 x Porta DVI-D

• 1 x Porta HDMI

• 4 x portas USB 2.0 (Suporta Proteção ESD (Proteção Total

contra Picos ASRock))

• 2 x portas USB 3.0 (Suporta Proteção ESD (Proteção Total

contra Picos ASRock))

• 1 x Porta LAN RJ-45 com LED (LED ACT/LIGAÇÃO e LED

DE VELOCIDADE)

• Ficha de áudio HD: Entrada de linha / Altifalante frontal /

Microfone

Português

Armazena-

mento

• 2 x conectores SATA3 a 6,0 Gb/s, com suporte para NCQ,

AHCI e Hot Plug

• 2 x conectores SATA2 a 3,0 Gb/s, com suporte para NCQ,

AHCI e Hot Plug

Conector

• 1 x Terminal de intrusão no chassis

• 1 x Terminal TPM

• 1 x Conector da ventoinha da CPU (4 pinos)

• 1 x Conector da ventoinha do chassis (4 pinos)

• 1 x conector de alimentação de 24 pinos ATX

• 1 x conector de alimentação de 12V de 4 pinos

• 1 x conector de áudio do painel frontal

• 2 x terminais USB 2.0 (suporte para 4 portas USB 2.0) (Suporta

Proteção ESD (Proteção Total contra Picos ASRock))

Funcionalida-

des da BIOS

• BIOS UEFI ocial da AMI com 32Mb com suporte de

interface multilíngue

• Eventos de reactivação compatíveis com ACPI 1.1

• Suporta SMBIOS 2.3.1

• Multi-ajuste de tensão de CPU, DRAM, PCH 1.05V

Monitor

de hardware

• Sensor de temperatura de CPU/Chassis

• Taquímetro de ventoinha de CPU/Chassis

• Ventoinha de CPU/Chassis silenciosa (Permite o ajuste

automático da velocidade da ventoinha do chassis através da

temperatura da CPU)

• Controlo de velocidade da ventoinha de CPU/Chassis

• Detecção de ABERTURA da CAIXA

• Monitorização da tensão: +12V, +5V, +3,3V, CPU Vcore

Sistema

Operativo

• Microso® Windows® 8.1 de 32 bits / 8.1 de 64 bits / 8 de 32

bits / 8 de 64 bits / 7 de 32 bits / 7 de 64 bits

Certicações

• FCC, CE, WHQL

• Preparada para ErP/EuP (é necessária uma fonte de

alimentação preparada para ErP/EuP)

* Para obter informações detalhadas acerca do produto, visite o nosso Web site:

http://www.asrock.com

Português

H81M-ITX/WiFi

Tenha em atenção que o overclocking inclui um determinado grau de risco, incluindo

o ajuste das denições na BIOS, a aplicação de tecnologia Untied Overclocking ou a

utilização de ferramentas de overclocking de terceiros. O overclocking poderá afectar

a estabilidade do sistema, ou mesmo causar danos aos componentes e dispositivos do

seu sistema. Overclocking deverá ser efectuado por sua conta e risco. Não nos respon-

sabilizamos por possíveis danos causados pelo overclocking.

Devido às limitações, o tamanho real da memória de 4GB reservada para utilização

em sistemas operativos Windows® 32-bits poderá ser inferior. Os sistemas operativos

Windows® 64-bits não possuem essas limitações. Pode utilizar o ASRock XFast RAM

para dar uso à memória que o Windows® não utiliza.

Português

1.3 Conguração dos jumpers

A imagem abaixo ilustra como os jumpers são congurados. Quando a tampa do

jumper é colocada nos pinos, o jumper é "Curto". Se não for colocada uma tampa

de jumper nos pinos, o jumper é "Aberto". A imagem ilustra um jumper de 3 pinos

cujos pino1 e pino2 estão "Curtos" quando a tampa do jumper é colocada nestes 2

pinos.

Jumper para limpar o

CMOS

(CLRCMOS1)

(consultar p.1, N.º 4)

CLRCMOS1 permite-lhe limpar os dados no CMOS. Para limpar e repor os

parâmetros do sistema para os valores predenidos, encerre o computador e

desligue a cha da tomada. Depois de aguardar 15 segundos, utilize uma tampa

de jumper para ligar o pino2 e o pino3 no CLRCMOS1 durante 5 segundos. No

entanto, não limpe o CMOS logo após ter efectuado a actualização da BIOS. Se

precisar de limpar o CMOS logo após ter terminado uma actualização da BIOS,

deverá primeiro iniciar o sistema e voltar a encerrá-lo antes de efectuar a acção

de limpeza do CMOS. Tenha em atenção que a palavra-passe, data, hora e perl

predenido de utilizador apenas serão limpos se a pilha do CMOS for retirada.

Limpar CMOS

Predenição

Se limpar o CMOS, poderá ser detectada a abertura da caixa. Ajuste a opção do BIOS

"Limpar estado" para limpar o registo anterior de estado de intrusão no chassis.

Português

H81M-ITX/WiFi

1.4 Terminais e conectores integrados

Terminal do painel de

sistema

(PAINEL1 de 9 pinos)

(consultar p.1, N.º 9)

Ligue o botão de

alimentação, o botão de

reposição e o indicador

do estado do sistema no

chassis a este terminal de

acordo com a descrição

abaixo. Tenha em atenção

os pinos positivos e

negativos antes de ligar os

cabos.

GND

RESET#

PWRBTN#

PLED-

PLED+

GND

HDLED-

HDLED+

GND

PWRBTN (Botão de alimentação):

Ligue ao botão de alimentação no painel frontal do chassis. Pode congurar a forma

para desligar o seu sistema através do botão de alimentação.

RESET (Botão de reposição):

Ligue ao botão de reposição no painel frontal do chassis. Prima o botão de reposição

para reiniciar o computador caso este bloqueie e não seja possível reiniciar

normalmente.

PLED (LED de alimentação do sistema):

Ligue ao indicador do estado da alimentação no painel frontal do chassis. O LED

cará acesso quando o sistema estiver em funcionamento. O LED cará intermitente

quando o sistema estiver nos estados de suspensão S1/S3. O LED cará desligado

quando o sistema estiver no estado de suspensão S4 ou desligado (S5).

HDLED (LED de actividade do disco rígido):

Ligue ao LED de actividade do disco rígido no painel frontal do chassis. O LED

cará acesso quando o disco rígido estiver a ler ou a escrever dados.

O design do painel frontal poderá variar dependendo do chassis. Um módulo de

painel frontal consiste principalmente em um botão de alimentação, um botão

de reposição, um LED de alimentação, um LED de actividade do disco rígido, um

altifalante, etc. Ao ligar o seu módulo de painel frontal do chassis a este conector,

certique-se de que os os e os pinos têm uma correspondência exacta.

Os terminais e conectores integrados NÃO são jumpers. NÃO coloque tampas de

jumpers sobre estes terminais e conectores. Colocar tampas de jumpers sobre os

terminais e conectores irá causar danos permanentes à placa principal.

Português

Conectores ATA2 de série

(SATA_2:

consultar p.1, N.º 13)

(SATA_3:

consultar p.1, N.º 14)

Estes dois conectores

SATA2 suportam

cabos de dados SATA

para dispositivos de

armazenamento interno

com uma velocidade de

transferência de dados de

até 3,0 Gb/s.

Conectores ATA3 de série

(SATA3_0:

consultar p.1, N.º 11)

(SATA3_1:

consultar p.1, N.º 12)

Estes dois conectores

SATA3 suportam

cabos de dados SATA

para dispositivos de

armazenamento interno

com uma velocidade de

transferência de dados de

até 6,0 Gb/s.

Terminais USB 2.0

(USB_4_5 de 9 pinos)

(consultar p.1, N.º 10)

(USB_6_7 de 9 pinos)

(consultar p.1, N.º 8)

Para além das quatro

portas USB 2.0 no painel

de E/S, existem duas

terminal nesta placa

principal. Cada terminal

USB 2.0 é capaz de

suportar duas portas.

Terminal de áudio do

painel frontal

(HD_AUDIO1 de 9 pinos)

(consultar p.1, N.º 15)

Este terminal destina-se

à ligação de dispositivos

áudio ao painel de áudio

frontal.

J_SENSE

OUT2_L

MIC_RET

PRESENCE#

GND

OUT2_R

MIC2_R

MIC2_L

OUT_RET

SATA3_1

SATA3_0

SATA_3

SATA_2

DUMMY

GND GND

-B

-A

USB_PWR

Português

H81M-ITX/WiFi

Conectores da ventoinha

do chassis

(CHA_FAN1 de 4 pinos)

(consultar p.1, N.º 16)

Ligue os cabos da

ventoinha aos conectores

da ventoinha colocando

o cabo preto no pino de

ligação à terra.

Conectores da ventoinha

da CPU

(CPU_FAN1 de 4 pinos)

(consultar p.1, N.º 1)

Esta placa principal inclui

um conector de ventoinha

de CPU (Ventoinha

silenciosa) de 4 pinos.

Se pretender ligar uma

ventoinha de CPU de 3

pinos, ligue-a ao Pino 1-3.

Conector de alimentação

ATX

(ATXPWR1 de 24 pinos)

(consultar p.1, N.º 6)

Esta placa principal

inclui um conector de

alimentação ATX de 24

pinos. Para utilizar uma

fonte de alimentação ATX

de 20 pinos, introduza-a

no Pino 1 o Pino 13.

1. O Áudio de alta denição suporta Detecção de cha, mas o cabo de painel no

chassis deverá suportar HDA para funcionar correctamente. Siga as instruções no

nosso manual e no manual do chassis para instalar o seu sistema.

2. Se utilizar um painel de áudio AC’97, instale-o no terminal de áudio do painel

frontal de acordo com os passos abaixo:

A. Ligue Mic_IN (MIC) a MIC2_L.

B. Ligue Audio_R (RIN) a OUT2_R e Audio_L (LIN) a OUT2_L.

C. Ligue Terra (GND) a Terra (GND).

D. MIC_RET e OUT_RET destinam-se apenas ao painel de áudio HD. Não precisa

de os ligar para o painel de áudio AC’97.

E. Para activar o microfone frontal, aceda ao separador “Microfone Frontal” no

painel de controlo Realtek e ajuste o “Volume de gravação”.

FAN_SPEED

FAN_SPEED_CONTROL

+12V

GND

FAN_SPEED

FAN_SPEED_CONTROL

+12V

GND

Português

Conector de alimentação

de 12V ATX

(ATX12V1 de 4 pinos)

(consultar p.1, N.º 2)

Ligue a fonte de

alimentação ATX 12V

neste conector.

Terminal de intrusão do

chassis

(CI1 de 2 pinos)

(consultar p.1, N.º 5)

Esta placa principal

suporta a função de

detecção de ABERTURA

da CAIXA que detecta

se a tampa do chassis foi

removida. Esta função

requer um chassis com

design de detecção de

intrusão.

Terminal TPM

(TPMS1 de 17 pinos)

(consultar p.1, N.º 7)

Este conector suporta

um sistema com Módulo

de Plataforma Conável

(TPM), que pode

armazenar com segurança

chaves, certicados

digitais, palavras-passe e

dados. Um sistema TPM

também ajuda a melhorar

a segurança de rede, a

proteger identidades

digitais e a garantir a

integridade da plataforma.

Signal

GND

SMB_DATA_MAIN

LAD2

LAD1

GND

S_PWRDWN#

SERIRQ#

GND

PCICLK

PCIRST#

LAD3

+3V

LAD0

+3VSB

GND

FRAME

SMB_CLK_MAIN

Türkçe

H81M-ITX/WiFi

1 Grş

ASRock'ın zorlu kalte kontrol süreçlernden geçmş olan ASRock H81M-ITX/WF

anakartını satın aldığınız çn teşekkür ederz. Sağlam tasarımı le ASRock'ın kalte

ve dayanıklılık taahhüdüne uygun şeklde mükemmel performans sağlar.

1.1 Ambalaj İçerğ

• ASRock H81M-ITX/WF Anakartı (Mn-ITX Form Faktörü)

• ASRock H81M-ITX/WF Hızlı Kurulum Kılavuzu

• ASRock H81M-ITX/WF Destek CD’s

• 1 x I/O Panel Kalkanı

• 2 x Ser ATA (SATA) Ver Kablosu (İsteğe Bağlı)

• 1 x WF-802.11ac Modülü

• 1 x SMA WF Anten Kabloları

• 1 x ASRock WF 2,4 GHz Antenler

• 1 x WF Modülü Desteğ

• 2 x WF Modülü çn Vda

Anakart özellkler ve BIOS yazılımı güncellenebleceğnden, bu dokümantasyonun

çerğ herhang br bldrmde bulunulmaksızın değştrleblr. Bu dokümantasyon

üzernde herhang br değşklk yapılması halnde, güncellenmş sürüm, herhang

br bldrm yapılmaksızın ASRock'ın web stesnde yer alacaktır.. Bu anakart le

lgl olarak teknk destek almak styorsanız, lütfen kullandığınız model hakkında

özel blgler çn web stemz zyaret edn. En güncel VGA kartları ve CPU destek

lstelern de ASRock'ın web stesnden bulablrsnz. ASRock'ın web stes http://

www.asrock.com.

Türkçe

1.2 Özellkler

Platform

• Mn-ITX Form Faktörü

• Katı Bağlayıcı tasarımı

• Yüksek Yoğunluklu Cam Elyaı Kumaş PCB

CPU

• Yen 4. ve 4. Nesl Intel® Core

7/5/3/Xeon®/Pentum®/

Celeron® İşlemclern destekler (Soket 1150)

• Intel® Turbo Boost 2.0 Teknolojsn destekler

Yonga kümes

• Intel® H81

Bellek

• Ç Kanallı DDR3 Bellek Teknolojs

• 2 x DDR3 DIMM yuvaları

• DDR3 1600/1333/1066 ECC olmayan, ara belleğe alınmamış

belleğ destekler

• Maksmum sstem belleğ kapastes: 16GB

(bkz. DİKKAT kazı)

• Intel® Üstün Bellek Profl (XMP)1.3/1.2 özellğn destekler

Genşletme

Yuvası

• 1 x PCI Express 2.0 x16 yuva

• 1 x Dkey Yarım Mn PCI Express Yuvası: WF Modülü çn

Grafkler

• Intel® HD Graphcs Dahl Görseller le VGA çıktıları,

yalnızca GPU entegre edlmş şlemcler le desteklenr.

• Intel® HD Graphcs Dahl Görsellern destekler : AVC,

MVC (S3D) ve MPEG-2 Full HW Encode1, Intel® InTru

3D,

Intel® Net Vdeo HD Teknolojs, Intel® Insder

, Intel® HD

Graphcs 4400/4600 le Intel® Quck Sync Vdeo

• Pxel Shader 5.0, DrectX 11.1

• Maksmum paylaşılan bellek 1792MB

• Üç VGA Çıkışı seçeneğ: D-sub, DVI-D ve HDMI

• Üçlü Monitör Desteği

• 1920x1200 @ 60Hz’ye kadar çözünürlükte HDMI

Teknolojsn destekler

• 1920x1200 @ 60Hz’ye kadar DVI-D şlevn destekler

• 1920x1200 @ 60Hz’ye kadar çözünürlükle D-Sub şlevn

destekler

• HDMI le Otomatk Dudak Senkronzasyonu (12bpc), xvYCC

ve HBR (Yüksek Bt Hızında Ses) özellklern destekler

(Uyumlu br HDMI montörü kullanılmalıdır)

Türkçe

H81M-ITX/WiFi

• DVI-D ve HDMI bağlantı noktaları le HDCP şlevn

destekler

• DVI-D, ve HDMI bağlantı noktalarıyla, Full HD 1080p Blu-

ray (BD) kayıttan yürütme özellklern destekler

Ses

• (Realtek ALC662 Ses Codec’) 5,1 Kanal HD Ses

• Dalgalanma Korumasını destekler (ASRock Tam An

Yükselş Koruması)

• ELNA Ses Kapakları

LAN

• PCIE x1 Ggabt LAN 10/100/1000 Mb/s

• Realtek RTL8111GR

• WAN üzerinden açma destekler

• LAN Açılışını Destekler

• Yıldırım/ESD Korumasını destekler (ASRock Tam An

Yükselş Koruması)

• LAN Kablo Algılama’yı destekler

• Enerj Vermllğne Sahp Ethernet 802.3az şlevn destekler

• PXE özellğn destekler

Kablosuz LAN

WF-802.11n modülü

• 1T1R 150Mbps IEEE 802.11n / 54Mbps IEEE 802.11g /

11Mbps IEEE 802.11b

• İstasyon modunu destekler (Altyapı modu ve Ad-hoc modu)

Arka Panel I/O

• 1 x PS/2 Fare/Klavye Bağlantı Noktası

• 1 x D-Sub Bağlantı Noktası

• 1 x DVI-D Bağlantı Noktası

• 1 x HDMI Bağlantı Noktası

• 4 x USB 2.0 Bağlantı noktası (ESD Korumasını destekler

(ASRock Tam An Yükselş Koruması))

• 2 x USB 3.0 Bağlantı noktası (ESD Korumasını destekler

(ASRock Tam An Yükselş Koruması))

• LED’e sahp 1 x RJ-45 LAN Bağlantı Noktası (ACT/LINK

LED ve SPEED LED)

• HD Ses Jakı: Hat Grş / Ön Hoparlör / Mkrofon

Türkçe

Depolama

• 2 x SATA3 6,0 Gb/s bağlayıcıları NCQ, AHCI ve Hot Plug

şlevlern destekler

• 2 x SATA2 3,0 Gb/s bağlayıcıları NCQ, AHCI ve Hot Plug

şlevlern destekler

Bağlayıcı

• 1 x Kasa Yetksz Erşm bağlantısı

• 1 x TPM bağlantısı

• 1 x CPU Fan bağlayıcısı (4-pn)

• 1 x Kasa Fanı bağlayıcısı (4-pn)

• 1 x 24 pn ATX güç bağlayıcısı

• 1 x 4 pn 12V güç bağlayıcısı

• 1 x Ön panel ses bağlayıcısı

• 2 x USB 2.0 bağlantısı (4 USB 2.0 bağlantı noktasını destekler)

(ESD Korumasını destekler (ASRock Tam An Yükselş

Koruması))

BIOS Özellğ

• Çok dll GUI Desteğ le 32Mb AMI UEFI Legal BIOS

• ACPI 1.1 Uyumluluğu Uyandırma Olayları

• SMBIOS 2.3.1 Desteğ

• CPU, DRAM, PCH 1,05V Voltaj Çoklu Ayarı

Donanım

Montörü

• CPU/Kasa Sıcaklığı Tespt

• CPU/Kasa Fanı Devrölçer

• CPU/Kasa Sessz Fan (Kasa Fan Hızının CPU Sıcaklığına

Göre Otomatk olarak Ayarlanmasını Sağlar)

• CPU/Kasa Fanı Çoklu Hız Kontrolü

• KASA AÇIK algılaması

• Voltaj Denetleme: +12V, +5V, +3,3V, CPU Vcore

• Mcroso® Wndows® 8.1 32-bt / 8.1 64-bt / 8 32-bt / 8 64-

bt / 7 32-bt / 7 64-bt

Belgeler

• FCC, CE, WHQL

• ErP/EuP çn hazır (ErP/EuP çn hazır güç beslemes

gerekldr)

* Detaylı ürün blgs çn, lütfen web stemz zyaret edn: http://www.asrock.com

Türkçe

H81M-ITX/WiFi

Lütfen, BIOS ayarlarını düzenleme, Bağımsız Hız Aşırtma Teknolojnn uygulanması

ya da üçüncü kşlern hız aşırtma araçlarının kullanılması da dahl olmak üzere

tüm hız aşırtma şlemlernn belrl br rsk taşıdığını unutmayın. Hız aşırtma, sste-

mnzn dayanıklılığını etkleyeblr, hatta sstemnzde yer alan bleşen ve aygıtlara

zarar vereblr. Bunu rsk ve masraarı sze at olmak üzere gerçekleştrlmeldr. Hız

aşırtmadan doğablecek zararlar konusunda sorumlu olmayacağız.

Sınırlamalar nedenyle, gerçek bellek boyutu Wndows® 32-bt şletm sstemler

çerçevesnde sstem kullanımına ayrıldığı çn 4GB'den az olablr. Wndows® 64-bt

şletm sstemlernde bu tür sınırlamalar yoktur. Wndows® tarafından kullanılma-

yan bellekten faydalanmak çn ASRock XFast RAM' kullanablrsnz.

Türkçe

1.3 Bağlantı Tel Kurulumu

Çzm, bağlantı tellernn kurulumunu göstermektedr. Tel kapağı, pmlern üzerne

yerleştrldğnde, tel "Kısa" olur. Pmlern üzernde tel kapağı bulunmadığında,

tel "Kısa" olur. Çzm, pn1 ve pn2 alanları "Kısa" olan ve bu k pm üzernde br

bağlantı tel kapağı bulunan 3-pn bağlantı teln göstermektedr.

CMOS'u Temzle Bağlantı

Tel

(CLRCMOS1)

(bkz. sf.1, No. 4)

CLRCMOS1, CMOS verlern temzlememz sağlar. Sstem parametrelern

temzlemek ve varsayılan kurulum ayarlarına sıfırlamak çn, lütfen blgsayarı

kapatın ve güç kablosunu güç beslemesnden çekn. 15 sanye bekledkten

sonra, CLRCMOS1 üzerndek pn2 ve pn3’ü 5 sanye boyunca kısaltmak çn

br bağlantı tel kullanın. Ancak, CMOS’u lütfen BIOS’u güncelledkten hemen

sonra temzlemeyn. BIOS’u güncelledkten hemen sonra CMOS’u temzlemenz

gerekrse, önce sstem başlatın ve ardından CMOS temzleme şlem öncesnde

yenden kapatın. Lütfen, parola, tarh, saat ve varsayılan kullanıcı proflnn

yalnızca CMOS bataryası çıkarıldığında temzleneceğn unutmayın.

CMOS'u Temzle

Varsayılan

CMOS'u temzlersenz, kasa açık uyarısı alablrsnz. Öncek kasa yetksz erşm

durumu kaydını slmek çn lütfen BIOS durumunu "Durumu Temzle" olarak

belrleyn.

Türkçe

H81M-ITX/WiFi

1.4 Ekl Bağlantılar ve Bağlayıcılar

Sstem Panel Bağlantısı

(9-pn PANEL1)

(bkz sf.1, No. 9)

Güç anahtarını bağlayın,

kasa üzerndek anahtar

le sstem durumu

belrtecn aşağıdak pm

düzenne göre sıfırlayın.

Kabloları bağlarken

poztf ve negatf pmler

not edn.

GND

RESET#

PWRBTN#

PLED-

PLED+

GND

HDLED-

HDLED+

GND

PWRBTN (Güç Anahtarı):

Güç anahtarını kasa ön panelne bağlayın. Güç anahtarını kullanarak sstemn hang

yöne hareketle kapanacağını seçeblrsnz.

RESET (Sıfırlama Anahtarı):

Sıfırlama anahtarını kasa ön panelne bağlayın. Blgsayarın kltlenmes ve normal

şeklde yenden başlatılamaması halnde reset (sıfırla) düğmesne basın.

PLED (Sstem Gücü LED):

Güç durumu belrtecn kasa ön panelne bağlayın. Sstem çalışırken LED ışığı

yanacaktır. Sstem S1/S3 uyku durumdayken LED ışığı yanıp söner. Sstem S4 uyku

durumunda ya da kapalıyken (S5) LED ışık kapanır.

HDLED (Sabt Dsk Aktvtes LED):

Sabt Dsk Aktvtes LED' kasanın ön panelne bağlayın. Sabt sürücü ver okur ya

da yazarken LED ışığı yanar.

Ön panel tasarımı kasaya göre değşklk göstereblr. Br ön panel modülü, temel

olarak br güç anahtarı, sıfırlama anahtarı, güç LED', sabt sürücü aktvtes LED',

hoparlör gb brmlerden oluşur. Kasanızın ön panel modülünü bu bağlantıya

takmadan önce, kablo düzenlemeler le pn düzenlemelernn düzgün şeklde

yapıldığından emn olun.

Ekl bağlantılar ve bağlayıcılar bağlantı tel değldr. Bağlantı tel kapaklarını bu

bağlantı ve bağlayıcılar üzerne yerleştrmeyn. Bağlantı tel kapaklarının bağlantılar

le bağlayıcılar üzerne yerleştrlmes, anakarta kalıcı hasar vereblr.

Türkçe

Ser ATA2 Bağlayıcıları

(SATA_2:

bkz. sf.1, No. 13)

(SATA_3:

bkz. sf.1, No. 14)

Bu k SATA2 bağlayıcısı,

ver aktarım hızı 3,0 Gb/

sn'ye kadar olan dahl

depolama aygıtları çn

tasarlanmış SATA ver

kablolarını destekler.

Ser ATA3 Bağlayıcıları

(SATA3_0:

bkz. sf.1, No. 11)

(SATA3_1:

bkz. sf.1, No. 12)

Bu k SATA3 bağlayıcısı,

ver aktarım hızı 6,0 Gb/

sn'ye kadar olan dahl

depolama aygıtları çn

tasarlanmış SATA ver

kablolarını destekler.

USB 2.0 Bağlantıları

(9-pn USB_4_5)

(bkz. sf.1, No. 10)

(9-pn USB_6_7)

(bkz. sf.1, No. 8)

Bu anakart üzernde,

I/O panel üzerndek

dört USB 2.0 bağlantı

noktasının yanı sıra,

k adet bağlantı

bulunmaktadır. Her

USB 2.0 bağlantısı, k

adet bağlantı noktasını

destekleyeblr.

Ön Panel Ses Bağlantısı

(9-pn HD_AUDIO1)

(bkz. sf.1, No. 15)

Bu bağlantı, ses

aygıtlarının ön ses

panelne bağlanması

çndr.

J_SENSE

OUT2_L

MIC_RET

PRESENCE#

GND

OUT2_R

MIC2_R

MIC2_L

OUT_RET

SATA3_1

SATA3_0

SATA_3

SATA_2

DUMMY

GND GND

-B

-A

USB_PWR

Türkçe

H81M-ITX/WiFi

Kasa Fanı Bağlayıcıları

(4-pn CHA_FAN1)

(bkz sf.1, No. 16)

Lütfen fan kablolarını

fan bağlayıcılarına takın

ve syah tel topraklama

pnne bağlayın.

CPU Fan Bağlayıcıları

(4-pn CPU_FAN1)

(bkz sf.1, No. 1)

Bu anakart, 4-Pn CPU

fan (Sessz Fan) bağlayıcısı

sağlamaktadır. 3-Pn CPU

fan bağlamak styorsanız,

lütfen Pn 1-3'ü kullanın.

ATX Güç Bağlayıcısı

(24-pn ATXPWR1)

(bkz. sf.1, No. 6)

Bu anakart, 24-pn

ATX güç bağlayıcısı

sağlamaktadır. 20-

pn ATX güç beslemes

kullanmak çn, lütfen Pn

1 ve Pn13'e bağlayın.

ATX 12V Güç Bağlayıcısı

(4-pn ATX12V1)

(bkz. sf.1, No. 2)

Lütfen br ATX 12V güç

kaynağını bu konektöre

bağlayın.

1. Yüksek Tanımlı Ses, Jak Algılama özellğn destekler, ancak bu şlevn düzgün

çalışablmes çn kasa üzerndek panel kablosunun HDA şlevn desteklemes

gerekmektedr. Sstemnz kurarken, lütfen kılavuzumuzdak talmatlar le kasa

kılavuzundak talmatları zleyn.

2. Br AC’97 ses panel kullanıyorsanız, lütfen bu panel aşağıdak adımları zleyerek

ön panel ses bağlantısına takın:

A. Mc_IN (MIC)' MIC2_L'ye bağlayın.

B. Audo_R (RIN)' OUT2_R'ye ve Audo_L (LIN)'y OUT2_L'ye bağlayın.

C. Topraklamayı (GND) Topraklamaya (GND) bağlayın.

D. MIC_RET ve OUT_RET, yalnızca HD ses panel çndr. Bunları AC'97 ses

panelnden bağlamanıza gerek yoktur.

E. Ön mkrofonu etknleştrmek çn Realtek Denetm panelnde yer alan "FrontMc

(Ön Mkrofon)" Sekmesne tıklayın ve "Recordng Volume (Kayıt Ses Düzey)"

değern ayarlayın.

FAN_SPEED

FAN_SPEED_CONTROL

+12V

GND

FAN_SPEED

FAN_SPEED_CONTROL

+12V

GND

Türkçe

Kasa Yetksz Erşm

Bağlantısı

(2-pn CI1)

(bkz. sf.1, No. 5)

Bu anakartın kasa

kapağının açılıp

açılmadığını tespt eden

br KASA AÇIK özellğ

bulunmaktadır. Bu

özellğn kullanılablmes

çn kasa yetksz erşm

tasarımına sahp br kasa

kullanılmalıdır.

TPM Bağlantısı

(17-pn TPMS1)

(bkz. sf.1, No. 7)

Bu bağlayıcı, anahtarlar,

djtal sertfkalar,

parolalar ve verler

güvenl br şeklde

saklama özellğ

bulunan Güvenlr

Platform Modülü (TPM)

sstemn destekler.

TPM sstemler, aynı

zamanda ağ güvenlğnn

artırılması, djtal

kmlklern korunması ve

platform bütünlüğünün

sağlanmasına da

yardımcıdır.

Signal

GND

SMB_DATA_MAIN

LAD2

LAD1

GND

S_PWRDWN#

SERIRQ#

GND

PCICLK

PCIRST#

LAD3

+3V

LAD0

+3VSB

GND

FRAME

SMB_CLK_MAIN

한 국 어

H81M-ITX/WiFi

1 개요

ASRock H81M-ITX/WiFi 마더보드를 구입해 주셔서 감사합니다 . 이 마더보드는

ASRock 의 일관되고 엄격한 품질관리 하에 생산되어 신뢰성이 우수합니다 . 품질

과 내구성에 대한 ASRock 의 기준에 부합하는 우수한 성능과 견고한 설계를 제공

합니다 .

1.1 포장 내용물

• ASRock H81M-ITX/WiFi 마더보드 (Mini-ITX 폼팩터 )

• ASRock H81M-ITX/WiFi 간편 설치 안내서

• ASRock H81M-ITX/WiFi 지원 CD

• I/O 패널 실드 1 개

• 시리얼 ATA (SATA) 데이터 케이블 2 개 ( 선택 품목 )

• WiFi-802.11ac 모듈 1 개

• SMA WiFi 안테나 케이블 1 개

• ASRock WiFi 2.4 GHz 안테나 1 개

• WiFi 모듈 브래킷 1 개

• WiFi 모듈 나사 2 개

마더보드 규격과 BIOS 소프트웨어를 업데이트할 수도 있기 때문에 , 이 문서의 내

용은 예고 없이 변경될 수 있습니다 . 이 설명서가 변경될 경우 , 업데이트된 버전은

ASRock 의 웹사이트에서 추가 통지 없이 제공됩니다 . 이 마더보드와 관련하여 기

술적 지원이 필요한 경우 , 당사의 웹사이트를 방문하여 사용 중인 모델에 대한 구체

적 정보를 구하십시오 . ASRock 의 웹사이트에서는 최신 VGA 카드와 CPU 지원 목

록도 찾을 수 있습니다 . ASRock 웹사이트 http://www.asrock.com.

한 국 어

1.2 규격

플랫폼

• Mini-ITX 폼 팩터

• 솔리드 콘덴서 구조

• 고 밀도 유리 직물 PCB

CPU

• 신형 4 세대 및 4 세대 Intel® Core

i7/i5/i3/Xeon®/Pentium®/

Celeron® 프로세서 ( 소켓 1150) 지원

• Intel

Turbo Boost 2.0 기술 지원

칩세트

• Intel

H81

메모리

• 듀얼 채널 DDR3 메모리 기술

• DDR3 DIMM 슬롯 2 개

• DDR3 1600/1333/1066 비 -ECC, 비버퍼링 메모리 지원

• 시스템 메모리 최대 용량 : 16GB

( 주의 참조 )

• Intel

Extreme Memory Prole (XMP)1.3/1.2 지원

확장 슬롯

• PCI Express 2.0 x16 슬롯 1 개

• 수직 하프 Mini-PCI Express 슬롯 1 개 : WiFi 모듈용

그래픽

• Intel

HD 그래픽스 빌트 - 인 비주얼과 VGA 출력은 GPU

통합 프로세서로만 지원할 수 있습니다 .

• Intel

HD 그래픽스 빌트 - 인 비주얼 지원 : AVC, MVC (S3D)

및 MPEG-2 풀 HW Encode1 지원 Intel

Quick Sync Video,

Intel

InTru

3D, Intel

클리어 비디오 HD 기술 , Intel

Insider

, Intel

HD 그래픽스 4400/4600

• Pixel Shader 5.0, DirectX 11.1

• 최대 공유 메모리 1792MB

• VGA 출력 옵션 세 개 : D-Sub, DVI-D 및 HDMI

• 삼중 모니터 지원

• HDMI 기술 지원 ( 최대 해상도 1920x1200 @ 60Hz)

• DVI-D 지원 ( 최대 해상도 1920x1200 @ 60Hz)

• D-Sub 지원 ( 최대 해상도 1920x1200 @ 60Hz)

• Auto Lip Sync, Deep Color (12bpc), xvYCC 및 HBR (High Bit

Rate Audio)(HDMI 포함 ) 지원 (HDMI 호환 모니터 필요 )

• DVI-D 및 HDMI 포트를 이용한 HDCP 기능 지원

한 국 어

H81M-ITX/WiFi

• DVI-D 및 HDMI 포트를 이용한 Full HD 1080p Blu-ray (BD)

재생 지원

오디오

• 5.1 CH HD 오디오 (Realtek ALC662 오디오 코덱 )

• 서지 보호 (ASRock 풀 스파이크 보호 ) 지원

• ELNA 오디오 캡

LAN

• PCIE 1 개 , Gigabit LAN 10/100/1000 Mb/s

• Realtek RTL8111GR

• Wake-On-WAN 지원

• Wake-On-LAN 지원

• 조명 /ESD 보호 (ASRock 풀 스파이크 보호 ) 지원

• LAN 케이블 감지 지원

• 절전형 이더넷 802.3az 지원

• PXE 지원

무선 LAN

WiFi-802.11n 모듈

• 1T1R 150Mbps IEEE 802.11n / 54Mbps IEEE 802.11g /

11Mbps IEEE 802.11b

• 스테이션 모드 지원 ( 인프라스트럭처 모드 및 애드혹 모드 )

후면 패널 I/O

• PS/2 마우스 / 키보드 포트 1 개

• D-Sub 포트 1 개

• DVI-D 포트 1 개

• HDMI 포트 1 개

• USB 2.0 포트 4 개 (ESD 보호 (ASRock 풀 스파이크 보호 ) 지

원 )

• USB 3.0 포트 2 개 (ESD 보호 (ASRock 풀 스파이크 보호 ) 지

원 )

• LED 장착 RJ-45 LAN 포트 1 개 (ACT/LINK LED 및 SPEED

LED)

• HD 오디오 잭 : 라인 입력 / 전면 스피커 / 마이크

저장 장치

• SATA3 6.0 Gb/s 커넥터 2 개 , NCQ, AHCI 및 핫 플러그 기능

지원

• SATA2 3.0 Gb/s 커넥터 2 개 , NCQ, AHCI 및 핫 플러그 기능

지원

100

한 국 어

커넥터

• 섀시 침입 헤더 1 개

• TPM 헤더 1 개

• CPU 팬 커넥터 1 개 (4 핀 )

• 섀시 팬 커넥터 1 개 (4 핀 )

• 24 핀 ATX 전원 커넥터 1 개

• 4 핀 12V 전원 커넥터 1 개

• 전면 패널 오디오 커넥터 1 개

• USB 2.0 헤더 2 개 (USB 2.0 포트 4 개 지원 ) (ESD 보호

(ASRock 풀 스파이크 보호 ) 지원 )

BIOS 기능

• 다국어 GUI 지원을 제공하는 32Mb AMI UEFI 적합형 BIOS

• ACPI 1.1 준수 웨이크 업 이벤트

• SMBIOS 2.3.1 지원

• CPU, DRAM, PCH 1.05V 전압 다중 조정

하드웨어

모니터

• CPU/ 섀시 온도 감지

• CPU/ 섀시 팬 타코미터

• CPU/ 섀시 저소음 팬 (CPU 온도에 의한 섀시 팬 속도 자동

조정 )

• CPU/ 섀시 팬 다중 속도 조절

• 케이스 열림 감지

• 전압 모니터링 : +12V, +5V, +3.3V, CPU Vcore

• Microso

Windows

8.1 32 비트 / 8.1 64 비트 / 8 32 비트 / 8

64 비트 / 7 32 비트 / 7 64 비트

인증

• FCC, CE, WHQL

• ErP/EuP 사용 가능 (ErP/EuP 사용 가능 전원공급장치 필요 )

BIOS 설정을 조정하거나 Untied Overclocking Technology 를 적용하거나 타업체의

오버클로킹 도구를 사용하는 것을 포함하는 오버클로킹에는 어느 정도의 위험이

따른다는 것을 유념하십시오 . 오버클로킹은 시스템 안정성에 영향을 주거나 심지

어 시스템의 구성 요소와 장치에 손상을 입힐 수도 있습니다 . 오버클로킹은 사용자

스스로 위험과 비용을 감수하고 해야 합니다 . 당사는 오버클로킹에 의해 발생할 수

있는 손상에 대해서 책임이 없습니다 .

* 자세한 제품 정보에 대해서는 당사 웹사이트를 참조하십시오 :

http://www.asrock.com

101

한 국 어

H81M-ITX/WiFi

1.3 점퍼 설정

그림은 점퍼를 어떻게 설정하는지 보여줍니다 . 점퍼 캡을 핀에 씌우면 점퍼가 ì 단

락î 됩니다 . 점퍼 캡을 핀에 씌우지 않으면 점퍼가 ì 단선î 됩니다 . 그림은 3 핀 점

퍼를 보여주며 핀 1 과 핀 2 는 점퍼 캡을 씌울 때 ì 단락î 됩니다 .

Clear CMOS 점퍼

(CLRCMOS1)

(1페이지, 4번 항목 참조)

CLRCMOS1 을 사용하여 CMOS 에 저장된 데이터를 지울 수 있습니다 . 시스

템 파라미터를 지우고 기본 설정으로 초기화하려면 컴퓨터를 끄고 전원 코

드를 전원공급장치에서 빼십시오 . 15 초 동안 기다린 후 점퍼 캡을 사용하여

CLRCMOS1 의 핀 2 와 핀 3 을 5 초 동안 단락시키십시오 . 그러나 BIOS 업데이

트 직후에는 CMOS 를 삭제하지 마십시오 . BIOS 업데이트를 완료한 직후 CMOS

를 지워야 할 경우 , 우선 시스템을 부팅한 후 바이오스 업데이트를 종료한 다음

CMOS 지우기 작업을 해야 합니다 . CMOS 배터리를 제거할 경우에만 암호 , 날

짜 , 시간 , 사용자 기본 프로파일이 지워집니다 .

Clear CMOS기본값

CMOS 를 지울 경우 케이스 열림이 감지될 수도 있습니다 . BIOS 옵션 ì Clear

Status( 상태 지우기 )î 를 조절하여 이전의 섀시 침입 상태에 대한 기록을 지우십시

오 .

제한 때문에 실제 메모리 크기는 Windows

32 비트 운영체제 하의 시스템 사용을

위한 예비 메모리용 4GB 보다 더 적을 수 있습니다 . Windows

64 비트 운영체제에

는 그러한 제한이 없습니다 . ASRock XFast RAM 을 사용하여 Windows

가 사용

할 수 없는 메모리를 이용할 수 있습니다 .

102

한 국 어

1.4 온보드 헤더 및 커넥터

시스템 패널 헤더

(9 핀 PANEL1)

(1 페이지 , 9 번 항목 참조 )

섀시의 전원 스위치 , 리

셋 스위치 , 시스템 상태

표시등을 아래의 핀 할

당에 따라 이 헤더에 연

결합니다 . 케이블을 연

결하기 전에 양극 핀과

음극 핀을 기록합니다 .

GND

RESET#

PWRBTN#

PLED-

PLED+

GND

HDLED-

HDLED+

GND

PWRBTN( 전원 스위치 ):

섀시 전면 패널의 전원 스위치에 연결합니다 . 전원 스위치를 이용해 시스템을 끄는

방법을 구성할 수 있습니다 .

RESET( 리셋 스위치 ):

섀시 전면 패널의 전원 스위치에 연결합니다 . 컴퓨터가 정지하고 정상적 재시작을

수행하지 못할 경우 리셋 스위치를 눌러 컴퓨터를 재시작합니다 .

PLED( 시스템 전원 LED):

섀시 전면 패널의 전원 상태 표시등에 연결합니다 . 시스템이 작동하고 있을 때는

LED 가 켜져 있습니다 . 시스템이 S1/S3 대기 상태에 있을 때는 LED 가 계속 깜박입

니다 . 시스템이 S4 대기 상태 또는 전원 꺼짐 (S5) 상태에 있을 때는 LED 가 꺼져 있

습니다 .

HDLED( 하드 드라이브 동작 LED):

섀시 전면 패널의 하드 드라이브 동작 LED 에 연결합니다 . 하드 드라이브가 데이

터를 읽거나 쓰고 있을 때 LED 가 켜져 있습니다 .

전면 패널 디자인은 섀시별로 다를 수 있습니다 . 전면 패널 모듈은 주로 전원 스위

치 , 리셋 스위치 , 전원 LED, 하드 드라이브 동작 LED, 스피커 등으로 구성되어 있

습니다 . 섀시 전면 패널 모듈을 이 헤더에 연결할 때 와이어 할당과 핀 할당이 정확

히 일치하는지 확인합니다 .

온보드 헤더와 커넥터는 점퍼가 아닙니다 . 점퍼 캡을 온보드 헤더와 커넥터에 씌우

지 마십시오 . 점퍼 캡을 온보드 헤더와 커넥터에 씌우면 마더보드가 영구적으로

손상됩니다 .

103

한 국 어

H81M-ITX/WiFi

시리얼 ATA2 커넥터

(SATA_2:

1 페이지 , 13 번 항목 참조 )

(SATA_3:

1 페이지 , 14 번 항목 참조 )

이들 두 개의 SATA2 커

넥터는 최대 3.0 Gb/s 데

이터 전송 속도를 제공

하는 내부 저장 장치용

SATA 데이터 케이블을

지원합니다 .

시리얼 ATA3 커넥터

(SATA3_0:

1 페이지 , 11 번 항목 참조 )

(SATA3_1:

1 페이지 , 12 번 항목 참조 )

이들 두 개의 SATA3 커

넥터는 최대 6.0 Gb/s 데

이터 전송 속도를 제공

하는 내부 저장 장치용

SATA 데이터 케이블을

지원합니다 .

USB 2.0 헤더

(9 핀 USB_4_5)

(1페이지, 10번 항목 참조)

(9 핀 USB_6_7)

(1 페이지 , 8 번 항목 참조 )

I/O 패널에 USB 2.0 포

트 네 개가 탑재되어 있

을 뿐 아니라 마더보드

에 헤더 두 개가 탑재되

어 있습니다 . 각 USB 2.0

헤더는 포트 두 개를 지

원할 수 있습니다 .

전면 패널 오디오 헤더

(9 핀 HD_AUDIO1)

(1페이지, 15번 항목 참조)

이 헤더는 오디오 장치

를 전면 오디오 패널에

연결하는 데 사용됩니

다 .

J_SENSE

OUT2_L

MIC_RET

PRESENCE#

GND

OUT2_R

MIC2_R

MIC2_L

OUT_RET

SATA3_1

SATA3_0

SATA_3

SATA_2

DUMMY

GND GND

-B

-A

USB_PWR

고음질 오디오는 잭 감지를 지원하지만 올바르게 작동하려면 섀시의 패널 와이어

가 HDA 를 지원해야 합니다 . 설명서 및 섀시 설명서에 나와 있는 지침을 따라 시

스템을 설치하십시오 .

ACí 97 오디오 패널을 사용할 경우 아래와 같은 절차를 따라 전면 패널 오디오

헤더에 설치하십시오 :

A. Mic_IN (MIC) 을 MIC2_L 에 연결합니다 .

B. Audio_R (RIN) 을 OUT2_R 에 연결하고 Audio_L (LIN) 을 OUT2_L 에 연결

합니다 .

C. 접지 (GND) 를 접지 (GND) 에 연결합니다 .

D. MIC_RET 및 OUT_RET 는 HD 오디오 패널에만 사용됩니다 . ACí 97 오디오

패널용으로 연결할 필요가 없습니다 .

E. 전면 마이크를 활성화하려면 Realtek 제어판에서 ì FrontMicî 탭으로 가서

ì Recording Volume( 녹음 볼륨 )î 을 조정합니다 .

104

한 국 어

섀시 팬 커넥터

(4 핀 CHA_FAN1)

(1페이지, 16 번 항목 참조)

팬 케이블을 팬 커넥터

에 연결하고 검은색 와

이어를 접지핀에 연결하

십시오 .

CPU 팬 커넥터

(4 핀 CPU_FAN1)

(1 페이지 , 1 번 항목 참조 )

이 마더보드에는 4 핀

CPU 팬 ( 저소음 팬 ) 커

넥터가 탑재되어 있습니

다 . 3 핀 CPU 팬을 연결

하려는 경우 핀 1-3 에 연

결하십시오 .

ATX 전원 커넥터

(24 핀 ATXPWR1)

(1 페이지 , 6 번 항목 참조 )

이 마더보드에는 24 핀

ATX 전원 커넥터가 탑

재되어 있습니다 . 20 핀

ATX 전원공급장치를 사

용하려면 핀 1 과 핀 13

을 따라 연결하십시오 .

ATX 12V 전원 커넥터

(4 핀 ATX12V1)

(1 페이지 , 2 번 항목 참조 )

ATX 12V 플러그가 달린

전원 공급장치를 이 커

넥터에연결해 야 충분한

전력을 공급할 수 있습

니다 . 그러지 않을 경우

전원을 켤 수 없습니다 .

섀시 침입 헤더

(2 핀 CI1)

(1 페이지 , 5 번 항목 참조 )

이 마더보드는 섀시 커

버가 제거될 경우 이를

감지하는 케이스 열림 감

지 기능을 지원합니다 .

이 기능을 사용하려면

섀시 침입 감지 설계가

적용된 섀시를 사용해야

합니다 .

FAN_SPEED

FAN_SPEED_CONTROL

+12V

GND

FAN_SPEED

FAN_SPEED_CONTROL

+12V

GND

Signal

GND

105

한 국 어

H81M-ITX/WiFi

TPM 헤더

(17 핀 TPMS1)

(1 페이지 , 7 번 항목 참조 )

이 커넥터는 키 , 디지

털 인증서 , 암호 및 데

이터를 안전하게 보관

할 수 있는 TPM(Trusted

Platform Module) 시스

템을 지원합니다 . TPM

시스템은 네트워크 보안

을 강화하고 , 디지털 신

원을 보호하며 플랫폼

무결성을 유지합니다 .

GND

SMB_DATA_MAIN

LAD2

LAD1

GND

S_PWRDWN#

SERIRQ#

GND

PCICLK

PCIRST#

LAD3

+3V

LAD0

+3VSB

GND

FRAME

SMB_CLK_MAIN

106

日本語

H81M-ITX/WiFi

1.1

• ASRock H81M-ITX/WiFi Mini-ITX

• ASRock H81M-ITX/WiFi

• ASRock H81M-ITX/WiFi CD

• 1 x I/O

• 2 x ATA SATA

• 1 x WiFi-802.11ac

• 1 x SMA Wi-Fi

• 1 x ASRock Wi-Fi 2.4 GHz

• 1 x Wi-Fi

• 2 x Wi-Fi

BIOS

VGA CPU

http://www.asrock.com.

107

日本語

H81M-ITX/WiFi

1.2

• Mini-ITX

•

• PCB

CPU

• 4 4 Intel® Core

i7/i5/i3/Xeon®/

Pentium®/Celeron® 1150

• Intel® 2.0

• Intel® H81

• DDR3

• 2 x DDR3 DIMM

• DDR3 1600/1333/1066 ECC

• 16GB (

• Intel® XMP 1.3/1.2

• 1 x PCI Express 2.0 x16

• 1 x PCI Express : WiFi

• Intel®HD VGA

GPU

• Intel®HD AVC

MVC (S3D) MPEG-2 HW 1 Intel® Quick

Sync Video Intel® InTru

3D Intel® HD

Intel®

Intel® HD

4400/4600

• 5.0 DirectX 11.1

• 1792MB

• 3 VGA D-Sub DVI-D HDMI

•

• HDMI 1920x1200

@60Hz

• DVI-D 1920x1200 @60Hz

• D-Sub 1920x1200 @60Hz

• HDMI HDMI

12bpc xvYCC HBR

108

日本語

• DVI-D HDMI HDCP

• DVI-D HDMI HD 1080p (BD)

• 5.1 CH HD (Realtek ALC662 Codec)

• ASRock

• ELNA

LAN

• PCIE x1 LAN 10/100/1000 Mb/

• Realtek RTL8111GR

• WAN

•

• /ESD (ASRock

• LAN

• 802.3az

• PXE

LAN

WiFi-802.11n

• 1T1R 150Mbps IEEE 802.11n / 54Mbps IEEE 802.11g /

11Mbps IEEE 802.11b

• (

)

I/O

• 1 x PS/2 /

• 1 x D-Sub

• 1 x DVI-D

• 1 x HDMI

• 4 x USB 2.0 ESD ASRock

• 2 x USB 3.0 ESD ASRock

• LED 1 x RJ-45 LAN ACT/LINK LED SPEED

LED

• HD / /

• 2 x SATA3 6.0 Gb/ NCQ AHCI

• 2 x SATA2 3.0 Gb/ NCQ AHCI

109

日本語

H81M-ITX/WiFi

• 1 x

• 1 x TPM

• 1 x CPU 4

• 1 x 4

• 1 x 24 ATX

• 1 x 4 12V

• 1 x

• 2 x USB 2.0 4 USB 2.0

ESD ASRock

BIOS

• GUI 32Mb AMI UEFI Legal BIOS

• ACPI 1.1

• SMBIOS 2.3.1

• CPU DRAM PCH 1.05V

• CPU/

• CPU/ CPU

• CPU/

•

• +12V +5V +3.3V CPU Vcore

• Microso® Windows® 8.1 32 / 8.1 64 / 8 32

/ 8 64 / 7 32 / 7 64

• FCC CE WHQL

• ErP/EuP Ready ErP/EuP ready

* http://www.asrock.com

110

日本語

BIOS

Windows® 32

4GB Windows®

Windows® XFast RAM

111

日本語

H81M-ITX/WiFi

1.3

1 2

CMOS

(CLRCMOS1)p.1 No. 4

CLRCMOS1 CMOS

15 CLRCMOS1

2 3 5

BIOS CMOS BIOS

CMOS

BIOS Clear

Status

112

日本語

1.4

9 1

p.1 No. 9

GND

RESET#

PWRBTN#

PLED-

PLED+

GND

HDLED-

HDLED+

GND

PWRBTN

RESET

PLED LED

LED S1/S3 LED

S4 S5

LED

HDLED LED

LED

113

日本語

H81M-ITX/WiFi

ATA2

(SATA_2:

p.1 No. 13

(SATA_3:

p.1 No. 14

2 SATA2

3.0 Gb/

SATA

ATA3

(SATA3_0:

p.1 No. 11

(SATA3_1:

p.1 No. 12 )

2 SATA3

6.0 Gb/

SATA

USB 2.0

9 USB_4_5

p.1 No. 10

9 USB_6_7

p.1 No. 8

I/O 4 USB

2.0

USB 2.0 2

9 HD_AUDIO1

p.1 No. 15

J_SENSE

OUT2_L

MIC_RET

PRESENCE#

GND

OUT2_R

MIC2_R

MIC2_L

OUT_RET

SATA3_1

SATA3_0

SATA_3

SATA_2

DUMMY

GND GND

-B

-A

USB_PWR

114

日本語

4 CHA_FAN1

p.1 No. 16

CPU

4 CPU_FAN1

p.1 No. 1

CPU

3 CPU

1-3

ATX

24 ATXPWR1

p.1 No. 6

ATX

1 13

ATX12V

4 ATX12V1

p.1 No. 2

ATX 12V

HDA

AC 97

A. Mic_IN (MIC) MIC2_L

B. Audio_R (RIN) OUT2_R Audio_L (LIN) OUT2_L

C. (GND) (GND)

D. MIC_RET OUT_RET HD AC 97

E. Realtek FrontMic

FAN_SPEED

FAN_SPEED_CONTROL

+12V

GND

FAN_SPEED

FAN_SPEED_CONTROL

+12V

GND

115

日本語

H81M-ITX/WiFi

2 CI1

p.1 No. 5

TPM

17 TPMS1

p.1 No. 7 TPM

TPM

Signal

GND

SMB_DATA_MAIN

LAD2

LAD1

GND

S_PWRDWN#

SERIRQ#

GND

PCICLK

PCIRST#

LAD3

+3V

LAD0

+3VSB

GND

FRAME

SMB_CLK_MAIN

116

簡体中文

1 简介

感谢您购买华擎 H81M-ITX/WiFi 主板，这是按照华擎一贯严格质量控制标准生

产的性能可靠的主板。它提供符合华擎质量和耐久性承诺的精良设计和卓越性

能。

1.1 包装清单

• 华擎 H81M-ITX/WiFi 主板（Mini-ITX 规格尺寸）

• 华擎 H81M-ITX/WiFi 快速安装指南

• 华擎 H81M-ITX/WiFi 支持光盘

• 1 x I/O 面板

• 2 x 串行 ATA (SATA) 数据线（选购）

• 1 x WiFi-802.11ac 模块

• 1 x SMA WiFi 天线线缆

• 1 x 华擎 WiFi 2.4 GHz 天线

• 1 x WiFi 模块支架

• 2 x WiFi 模块用螺丝

由于主板规格和 BIOS 软件可能已更新，因此，本文档的内容可能会随时更改，恕

不另行通知。如果本文档有任何修改，则更新的版本将发布在华擎网站上，我们不

会另外进行通知。如果您需要与此主板相关的技术支持，请访问我们的网站以具

体了解所用型号的信息。您也可以在华擎网站上找到最新 VGA 卡和 CPU 支持列

表。华擎网站 http://www.asrock.com。

117

簡体中文

H81M-ITX/WiFi

1.2 规格

平台

• Mini-ITX 规格

• 固态电容器设计

• 高密度防潮纤维电路板

CPU

• 支持新款第 4 代和第 4 代 Intel® Core

i7/i5/i3/Xeon®/

Pentium®/Celeron® 处理器 (Socket 1150)

• 支持 Intel® Turbo Boost 2.0 技术

芯片组

• Intel® H81

内存

• 双通道 DDR3 内存技术

• 配备 2 个 DDR3 DIMM 插槽

• 支持 DDR3 1600/1333/1066 non-ECC， un-buered 内存

• 系统内存最大容量 : 16GB （见“注意”）

• 支持 Intel® Extreme Memory Prole (XMP) 1.3 / 1.2 技术

扩充槽

• 1 x PCI Express 2.0 x16 插槽

• 1 x 垂直半高 Mini-PCI Express 插槽：供 WiFi 模块使用

图形

• 仅内置 GPU 的处理器可支持 Intel® HD Graphics Built-in

Visuals 与 VGA 输出。

• 支持 Intel® HD Graphics 内置视觉技术 (Built-in Visuals) :

Intel® 快速同步视频，采用 AVC、MVC (S3D) 和 MPEG-2

Full HW Encode1, Intel® InTru

3D, Intel® Clear Video HD

技术 , Intel® Insider

, Intel® HD Graphics 4400/4600

• Pixel Shader 5.0、DirectX 11.1

• 最大共享显示内存 1792 MB

• 三个 VGA 输出选项： D-Sub、DVI-D 和 HDMI

• 支持三台监视器

• 支持 HDMI 技术，60Hz 时最大分辨率达 1920x1200

• 支持 DVI-D，60Hz 时最大分辨率达 1920x1200

• 支持 D-Sub，60Hz 时最大分辨率达 1920x1200

• 通过 HDMI（需要符合规格的 HDMI 监视器）支持 Auto Lip

Sync、Deep Color (12bpc), xvYCC 和 HBR（高位速率音频）

• 通过 DVI-D and HDMI 端口支持 HDCP 功能

118

簡体中文

• 通过 DVI-D 和 HDMI 端口支持全高清 1080p Blu-ray (BD)

播放

音频

• 5.1 声道高保真音频 (Realtek ALC662 音频编码解码器 )

• 支持防突波 ( 华擎全防护 )

• ELNA 专业音效电容

LAN

• PCIE x1 千兆网卡 10/100/1000 Mb/s

• Realtek RTL8111GR

• 支持远端開机功能 (Wake-On-WAN)

• 支持网络唤醒功能 (Wake-On-LAN)

• 支持防雷击 / 防 ESD 静电 ( 华擎全防护 )

• 支持网线侦测

• 支持 Energy Ecient Ethernet 802.3az

• 支持 PXE

无线 LAN

WiFi-802.11n 模块

• 1T1R 150Mbps IEEE 802.11n / 54Mbps IEEE 802.11g /

11Mbps IEEE 802.11b

• 支持工作站模式（基础结构模式和 Ad-hoc 模式）

后面板 I/O

• 1 x PS/2 鼠标 / 键盘接口

• 1 x D-Sub 接口

• 1 x DVI-D 接口

• 1 x HDMI 接口

• 4 x USB 2.0 接口 ( 支持防 ESD 静电 ( 华擎全防护 ))

• 2 x USB 3.0 接口 ( 支持防 ESD 静电 ( 华擎全防护 ))

• 1 x RJ-45 网卡接口 LED 指示灯 (ACT/LINK LED 和 SPEED

LED)

• HD 音频插孔 : 线性输入 / 前置喇叭 / 麦克风

存储

• 2 x SATA3 6.0 Gb/s 接口，支持 NCQ、AHCI 和热插拔

• 2 x SATA2 3.0 Gb/s 接口，支持 NCQ、AHCI 和热插拔

接口

• 1 x 机箱侵入接脚

• 1 x TPM 接脚

• 1 x CPU 风扇接口 (4 针 )

• 1 x 机箱风扇接口 (4 针 )

119

簡体中文

H81M-ITX/WiFi

• 1 x 24 针 ATX 电源接口

• 1 x 4 针 12V 电源接口

• 1 x 前面板音频接口

• 2 x USB 2.0 接脚（支持 4 个 USB 2.0 端口）( 支持防 ESD 静

电 ( 华擎全防护 ))

BIOS 功能特点

• 32Mb AMI UEFI Legal BIOS、具有多语言 GUI 支持

• 符合 ACPI 1.1、支持唤醒与自动开机 (Wake Up Events)

• 支持 SMBIOS 2.3.1

• CPU、內存、PCH 1.05V 电压多功能调节器

硬件监控

• CPU / 机箱温度检测

• CPU / 机箱转速计

• CPU / 机箱静音风扇 ( 可根据处理器温度自动调节机箱风

扇转速 )

• CPU / 机箱风扇多速控制

• CASE OPEN（机箱打开）检测

• 电压实时监控 : +12V、+5V、+3.3V、核心电压

操作系统

• Microso® Windows® 8.1 32-bit / 8.1 64-bit / 8 32-bit / 8 64-

bit / 7 32-bit / 7 64-bit

认证

• FCC、CE、WHQL

• 支持 ErP/EuP ( 需要搭配支持 ErP/EuP 的电源供应器）

须认识到超频会有一定风险，包括调整 BIOS 设置，应用“自由超频技术”，或使用

第三方超频工具。超频可能会影响到系统的稳定性，甚至对系统的组件和设备造

成损坏。执行这项工作您应自担风险和自己承担费用。我们对由于超频而造成的

损坏概不负责。

* 有关详细产品信息，请访问我们的网站： http://www.asrock.com

由于限制原因，实际内存容量可能会小于 4GB，以保留给 Windows® 32-bit 操作系

统下的系统使用。Windows® 64-bit 操作系统没有此类限制。您可以使用 ASRock

XFast RAM 来利用 Windows® 不能使用的内存。

120

簡体中文

1.3 跳线设置

此图显示如何设置跳线。将跳线帽装到这些针脚上时，跳线 “短接”。如果这些

针脚上没有装跳线帽，跳线 “开路”。此图显示 3 针跳线，当跳线帽装在针脚 1 和

针脚 2“上，它们短接”。

清除 CMOS 跳线

(CLRCMOS1)

（见第 1 页，第 4 个）

CLRCMOS1 允许您清除 CMOS 中的数据。要清除和重置系统参数到默认设

置，请关闭计算机，从电源上拔下电源线插头。等候 15 秒后，使用跳线帽将

CLRCMOS1 上的针脚 2 和针脚 3 短接 5 秒。但是，请勿在更新 BIOS 后立即清

除 CMOS。如果您需要在刚完成 BIOS 更新后清除 CMOS，则必须先启动系统，

并在关闭后再执行清除 CMOS 操作。请注意，密码、日期、时间和用户默认配置

文件只在卸下 CMOS 电池后才会被清除。

清除 CMOS

默认

如果您清除 CMOS，机箱打开会被检测到。请将 BIOS 选项“Clear Status”（清除

状态）调整为清除前一个机箱侵入状态的记录。

121

簡体中文

H81M-ITX/WiFi

1.4 板载接脚和接口

系统面板接脚

(9 针 PANEL1)

( 见第 1 页，第 9 个）

按照下面的针脚分配，将

机箱上的电源开关、重置

开关和系统状态指示灯

连接到此接脚。在连接线

缆前请记下正负针脚。

PWRBTN ( 电源开关 ):

连接到机箱前面板上的电源开关。您可以配置使用电源开关关闭系统的方式。

RESET ( 重置开关 ):

连接到机箱前面板上的重置开关。如果计算机死机，无法执行正常重新启动，按重

置开关重新启动计算机。

PLED（系统电源 LED）：

连接到机箱前面板上的状态指示灯。系统操作操作时，此 LED 亮起。系统处在 S1/

S3 睡眠状态时，此 LED 闪烁。系统处在 S4 睡眠状态或关机 (S5) 时，此 LED 熄灭。

HDLED（硬盘活动指示灯）：

连接到机箱前面板上的硬盘活动 LED 指示灯。硬盘正在读取或写入数据时，此

LED 亮起。

前面板设计根据机箱不同而有所差异。前面板模块主要包括电源开关、重置开关、

电源 LED、硬盘活动 LED 指示灯、扬声器等。将机箱前面板模块连接到此接脚时，

确保连线分配和针脚分配正确匹配。

板载接脚和接口不是跳线。不要将跳线帽装到这些接脚和接口上。将跳线帽装到

这些接脚和接口上将会对主板造成永久性损坏。

GND

RESET#

PWRBTN#

PLED-

PLED+

GND

HDLED-

HDLED+

GND

122

簡体中文

SATA2 接口

(SATA_2:

见第 1 页，第 13 个）

(SATA_3:

见第 1 页，第 14 个）

这两个 SATA2 接口支持

最高 3.0 Gb/s 数据传输

速率的内部存储设备的

SATA 数据线。

SATA3 接口

(SATA3_0:

见第 1 页，第 11 个）

(SATA3_1:

见第 1 页，第 12 个）

这两个 SATA3 接口支持

最高 6.0 Gb/s 数据传输

速率的内部存储设备的

SATA 数据线。

USB 2.0 接脚

(9 针 USB_4_5)

（见第 1 页，第 10 个）

(9 针 USB_6_7)

（见第 1 页，第 8 个）

除 I/O 面板上的四个

USB 2.0 端口外，此主板

上还有两个接脚。這个

USB 2.0 接脚可以支持两

个端口。

前面板音频接脚

(9 针 HD_AUDIO1)

（见第 1 页，第 15 个）

此接脚用于将音频设备

连接到前音频面板。

J_SENSE

OUT2_L

MIC_RET

PRESENCE#

GND

OUT2_R

MIC2_R

MIC2_L

OUT_RET

SATA3_1

SATA3_0

SATA_3

SATA_2

DUMMY

GND GND

-B

-A

USB_PWR

123

簡体中文

H81M-ITX/WiFi

机箱风扇接口

(4 针 CHA_FAN1)

见第 1 页，第 16 个）

请将风扇线连接到风扇

接口并使黑线匹配接地

针脚。

CPU 风扇接口

(4 针 CPU_FAN1)

( 见第 1 页，第 1 个）

此主板提供 4 针 CPU 风

扇（静音风扇）接口。如果

您打算连接 3 针 CPU 风

扇，请将它连接到脚 1-3。

ATX 电源接口

(24 针 ATXPWR1)

（见第 1 页，第 6 个）

此主板提供 24 针 ATX

电源接口。要使用 20 针

ATX 电源，请沿针脚 1 和

针脚 13 插接它。

ATX 12V 电源接口

(4 针 ATX12V1)

（见第 1 页，第 2 个）

请

将

一個 ATX 12V 电源

供应器接到此接口。

高清音频支持插孔感测，但机箱上的面板连线必须支持 HDA 才能正常工作。请

按照我们的手册和机箱手册的说明安装系统。

如果您使用 AC’97 音频面板，请按照以下步骤安装到前面板音频接脚：

A. 将 Mic_IN (MIC) 连接到 MIC2_L.

B. 将 Audio_R (RIN) 连接到 OUT2_R，将 Audio_L (LIN) 连接到 OUT2_L.

C. 将接地端 (GND) 连接到接地端 (GND)。

D. MIC_RET 和 OUT_RET 只用于高清音频面板。您不需要针对 AC’97 音频面

板连接它们。

E. 要启用前麦克风，请转到 Realtek 控制面板上的“FrontMic”（前麦克风）选项

卡，调整 “Recording Volume”（录音音量）。

FAN_SPEED

FAN_SPEED_CONTROL

+12V

GND

FAN_SPEED

FAN_SPEED_CONTROL

+12V

GND

124

簡体中文

机箱侵入接脚

(2 针 CI1)

（见第 1 页，第 5 个）

此主板支持 CASE OPEN

（机箱打开）检测功能 -

检测机箱盖是否拆下。此

功能需要采用侵入检测

设计的机箱。

TPM 接脚

(17 针 TPMS1)

（见第 1 页，第 7 个）

此接口支持 Trusted

Platform Module（信任平

台模块，TPM）系统，可

以安全地存储密钥、数字

证书、密码和数据。TPM

系统也可以帮助增强网络

安全，保护数字身份和确

保平台完整性。

Signal

GND

SMB_DATA_MAIN

LAD2

LAD1

GND

S_PWRDWN#

SERIRQ#

GND

PCICLK

PCIRST#

LAD3

+3V

LAD0

+3VSB

GND

FRAME

SMB_CLK_MAIN

125

簡体中文

H81M-ITX/WiFi

電子信息產品污染控制標示

依據中國發布的「電子信息產品污染控制管理辦法」及 SJ/T 11364-2006「電

子信息產品污染控制標示要求」，電子信息產品應進行標示，藉以向消費者揭

露產品中含有的有毒有害物質或元素不致發生外洩或突變從而對環境造成污染

或對人身、財產造成嚴重損害的期限。依上述規定，您可于本產品之印刷電路

板上看見圖一之標示。圖一中之數字為產品之環保使用期限。由此可知此主板

之環保使用期限為 10 年。

圖一

有毒有害物質或元素的名稱及含量說明

若您慾了解此產品的有毒有害物質或元素的名稱及含量說明，請參照以下表格

及說明。

有害物質或元素

鉛 (Pb) 鎘(Cd) 汞 (Hg) 六价鉻 (Cr(VI)) 多溴聯苯(PBB) 多溴二苯醚 (PBDE)

印刷電路板

及電子組件

外部信號連

接頭及線材

部件名稱

X O O O O O

表示該有毒有害物質在該部件所有均質材料中的含量均在 SJ/T 11363-2006 標準規定

的限量要求以下。

表示該有毒有害物質至少在該部件的某一均質材料中的含量超出 SJ/T 11363-2006 標準

規定的限量要求，然該部件仍符合歐盟指令 2002/95/EC 的規範。

備註 : 此產品所標示之環保使用年限，系指在一般正常使用狀況下。

126

繁體中文

1 簡介

感謝您購買華擎 H81M-ITX/WiFi 主機板，本主機板經華擎嚴格品管製作，是一

套讓人信賴的可靠產品。本產品採耐用設計所展現的優異效能，完全符合華擎對

品質及耐用度的承諾。

1.1 包裝內容

• 華擎 H81M-ITX/WiFi 主機板（Mini-ITX 尺寸）

• 華擎 H81M-ITX/WiFi 快速安裝指南

• 華擎 H81M-ITX/WiFi 支援光碟

• 1 x I/O 面板外罩

• 2 x Serial ATA (SATA) 資料纜線（選用）

• 1 x WiFi-802.11ac 模組

• 1 x SMA WiFi 天線纜線

• 1 x 華擎 WiFi 2.4 GHz 天線

• 1 x WiFi 模組架

• 2 x 顆 WiFi 模組螺絲

由於主機板規格及 BIOS 軟體可能會更新，所以本文件內容如有變更，恕不另行通

知。如本文件有任何修改，可至華擎網站逕行取得更新版本，不另外通知。若您

需要與本主機板相關的技術支援，請上我們的網站瞭解有關您使用機型的特定資

訊。您也可以在華擎網站找到最新的 VGA 卡及 CPU 支援清單。華擎網站 http://

www.asrock.com.

127

繁體中文

H81M-ITX/WiFi

1.2 規格

平台

• Mini-ITX 尺寸

• 固態電容設計

• 高密度防潮纖維電路板

CPU

• 支援全新第 4 代及第 4 代 Intel® Core

i7/i5/i3/Xeon®/

Pentium®/Celeron® 處理器 (Socket 1150)

• 支援 Intel® Turbo Boost 2.0 技術

晶片組

• Intel® H81

記憶體

• 雙通道 DDR3 記憶體技術

• 2 x DDR3 DIMM 插槽

• 支援 DDR3 1600/1333/1066 非 ECC、無緩衝記憶體

• 最大系統記憶體容量： 16GB

（請參閱「注意」）

• 支援 Intel® Extreme Memory Prole (XMP)1.3/1.2

擴充插槽

• 1 x PCI Express 2.0 x16 插槽

• 1 x 直式半高迷你 PCI Express 插槽：適用於 WiFi 模組

顯示卡

• 僅限整合 GPU 的處理器才可支援 Intel® HD Graphics Built-

in Visuals 及 VGA 輸出。

• 支援 Intel® HD Graphics Built-in Visuals：轉換 AVC、MVC (S3D)

及 MPEG-2 Full HW Encode1 的 Intel® 高速影像同步轉檔技

術、Intel® InTru

3D、Intel® Clear Video HD Technology、

Intel® Insider

、Intel® HD Graphics 4400/4600

• Pixel Shader 5.0，DirectX 11.1

• 最大共用記憶體 1792MB

• 三個 VGA 輸出選項： D-Sub、DVI-D 及 HDMI

• 支援三台顯示器

• 支援最高達 1920x1200 @ 60Hz 解析度的 HDMI 技術

• 支援最高達 1920x1200 @ 60Hz 解析度的 DVI-D

• 支援最高達 1920x1200 @ 60Hz 解析度的 D-Sub

• 支援使用 HDMI（需相容於 HDMI 監視器）的 Auto Lip Sync、

Deep Color (12bpc)、xvYCC 及 HBR（高位元率音訊）

128

繁體中文

• 支援含 DVI-D 及 HDMI 連接埠的 HDCP 功能

• 支援透過 DVI-D 及 HDMI 連接埠的 Full HD 1080p Blu-ray

(BD) 播放

音訊

• 5.1 聲道高清晰音效（Realtek ALC662 音效編解碼器）

• 支援防突波 ( 華擎全防護 )

• ELNA 音效專用電容

LAN

• PCIE x1 Gigabit LAN 10/100/1000 Mb/s

• Realtek RTL8111GR

• 支援 Wake-On-WAN

• 支援網路喚醒

• 支援防雷擊 / 防 ESD 靜電 ( 華擎全防護 )

• 支援網路線偵測功能

• 支援 Energy Ecient Ethernet 802.3az

• 支援 PXE

無線網路

WiFi-802.11n 模組

• 1T1R 150Mbps IEEE 802.11n/54Mbps IEEE 802.11g/11Mbps

IEEE 802.11b

• 支援工作站模式（基礎結構模式和臨機操作模式）

後面板 I/O

• 1 x PS/2 滑鼠 / 鍵盤連接埠

• 1 x D-Sub 連接埠

• 1 x DVI-D 連接埠

• 1 x HDMI 連接埠

• 4 x USB 2.0 連接埠 ( 支援防 ESD 靜電 ( 華擎全防護 )

• 2 x USB 3.0 連接埠 ( 支援防 ESD 靜電 ( 華擎全防護 )

• 1 x RJ-45 LAN 連接埠，含 LED（ACT/LINK LED 及 SPEED

LED）

• HD 音訊插孔：線路輸入／前置喇叭／麥克風

儲存裝置

• 2 x SATA3 6.0 Gb/s 接頭，支援 NCQ、AHCI 及熱插拔

• 2 x SATA2 3.0 Gb/s 接頭，支援 NCQ、AHCI 及熱插拔

接頭

• 1 x 機殼防護標頭

• 1 x TPM 標頭

• 1 x CPU 風扇接頭 (4-pin)

129

繁體中文

H81M-ITX/WiFi

請務必理解，超頻可能產生某種程度的風險，其中包括調整 BIOS 中的設定、採用

自由超頻技術或使用協力廠商的超頻工具。超頻可能會影響您系統的穩定性，或

者甚至會對您系統的元件及裝置造成傷害。您應自行負擔超頻風險及成本。我們

對於因超頻所造成的可能損害概不負責。

* 如需產品詳細資訊，請上我們的網站： http://www.asrock.com

在 Windows® 32 位元作業系統下，因有保留供系統使用記憶體的限制，所以實際

記憶體大小可能低於 4GB。Windows® 64 位元作業系統則沒有此類限制。您可使

用華擎 XFast RAM 運用 Windows® 無法使用的記憶體。

• 1 x 機殼風扇接頭 (4-pin)

• 1 x 24 pin ATX 電源接頭

• 1 x 4 pin 12V 電源接頭

• 1 x 前面板音訊接頭

• 2 x USB 2.0 標頭（支援 4 USB 2.0 連接埠）( 支援防 ESD 靜電

( 華擎全防護 )

BIOS 功能

• 32Mb AMI UEFI Legal BIOS 含多語 GUI 支援

• ACPI 1.1 符合喚醒自動開機

• 支援 SMBIOS 2.3.1

• CPU、DRAM、PCH 1.05V 電壓多重調整

硬體

監視器

• CPU/ 機殼溫度感應

• CPU/ 機殼風扇轉速計

• CPU/ 機殼靜音風扇（允許按照 CPU 溫度自動調整機殼風扇

速度）

• CPU/ 機殼風扇多重速度控制

• 機殼開啟偵測

• 電壓監控： +12V、+5V、+3.3V、CPU Vcore

作業系統

• Microsoft® Windows® 8.1 32 位元 /8.1 64 位元 /8 32 位元 /8

64 位元 /7 32 位元 /7 64 位元

認證

• FCC、CE、WHQL

• ErP/EuP Ready（需具備 ErP/EuP ready 電源供應器）

130

繁體中文

1.3 跳線設定

圖例顯示設定跳線的方式。跳線蓋套在針腳上時，該跳線為「短路」。若沒有跳

線蓋套在針腳上，該跳線為「開啟」。圖例顯示 3-pin 跳線的跳線蓋套在 pin1 及

pin2 時，這兩個針腳皆為「短路」。

清除 CMOS 跳線

(CLRCMOS1)

（請參閱第 1 頁，編號 4）

您可利用 CLRCMOS1 清除 CMOS 中的資料。若要清除及重設系統參數為預設設

定，請先關閉電腦電源，再拔下電源供應器的電源線。在等待 15 秒後，請使用

跳線蓋讓 CLRCMOS1 上的 pin2 及 pin3 短路約 5 秒。不過，請不要在更新 BIOS

後立即清除 CMOS。若您需在更新 BIOS 後立即清除 CMOS，則必須先重新啟動

系統，然後於進行清除 CMOS 動作前關機。請注意，只有在取出 CMOS 電池時

才會清除密碼、日期、時間及使用者預設設定檔。

清除 CMOS

預設

若您清除 CMOS，可能會偵測到機殼開啟。請調整 BIOS 選項「清除狀態」，清除先

前機殼防護狀態的紀錄。

131

繁體中文

H81M-ITX/WiFi

1.4 板載標頭及接頭

系統面板標頭

(9-pin PANEL1)

（請參閱第 1 頁，編號 9）

請依照以下的針腳

排列將機殼上的電

源開關、重設開關及

系統狀態指示燈連

接至此標頭。在連接

纜線之前，請注意正

負針腳。

PWRBTN（電源開關）：

連接至機殼前面板上的電源開關。您可設定使用電源開關關閉系統電源的方式。

RESET（重設開關）：

連接至機殼前面板上的重設開關。若電腦凍結且無法執行正常重新啟動，按下重

設開關即可重新啟動電腦。

PLED（系統電源 LED）：

連接至機殼前面板上的電源狀態指示燈。系統正在運作時，此 LED 會亮起。系統

進入 S1/S3 睡眠狀態時，LED 會持續閃爍。系統進入 S4 睡眠狀態或關機 (S5) 時，

LED 會熄滅。

HDLED（硬碟活動 LED）：

連接至機殼前面板上的硬碟活動 LED。硬碟正在讀取或寫入資料時，LED 會亮起。

各機殼的前面板設計各有不同。前面板模組主要是由電源開關、重設開關、電源

LED、硬碟活動 LED、喇叭及其他裝置組成。將機殼前面板模組連接至此標頭時，

請確定佈線及針腳指派皆正確相符。

板載標頭及接頭都不是跳線，請勿將跳線蓋套在這些標頭及接頭上。將跳線蓋套

在標頭及接頭上，將造成主機板永久性的受損。

GND

RESET#

PWRBTN#

PLED-

PLED+

GND

HDLED-

HDLED+

GND

132

繁體中文

Serial ATA2 接頭

(SATA_2:

( 請參閱第 1 頁，編號 13)

(SATA_3:

( 請參閱第 1 頁，編號 14)

這兩組 SATA2 接頭皆

支援內部儲存裝置的

SATA 資料纜線，最高

可達 3.0 Gb/s 資料傳

輸率。

Serial ATA3 接頭

(SATA3_0:

( 請參閱第 1 頁，編號 11）

(SATA3_1:

( 請參閱第 1 頁，編號 12)

這兩組 SATA3 接頭皆

支援內部儲存裝置的

SATA 資料纜線，最高

可達 6.0 Gb/s 資料傳

輸率。

USB 2.0 標頭

(9-pin USB_4_5)

（請參閱第 1 頁，編號 10）

(9-pin USB_6_7)

（請參閱第 1 頁，編號 8）

除了 I/O 面板上的

四個 USB 2.0 連接埠

外，在本主機板上還

有另外兩組標頭。此

USB 2.0 標頭可支援

兩個連接埠。

前面板音訊標頭

(9-pin HD_AUDIO1)

（請參閱第 1 頁，編號 15）

本標頭適用於連接

音訊裝置至前面板

音訊。

J_SENSE

OUT2_L

MIC_RET

PRESENCE#

GND

OUT2_R

MIC2_R

MIC2_L

OUT_RET

SATA3_1

SATA3_0

SATA_3

SATA_2

DUMMY

GND GND

-B

-A

USB_PWR

133

繁體中文

H81M-ITX/WiFi

機殼風扇接頭

(4-pin CHA_FAN1)

（請參閱第 1 頁，編號 16）

請將風扇纜線連接

至風扇接頭，並比對

黑線及接地針腳。

CPU 風扇接頭

(4-pin CPU_FAN1)

（請參閱第 1 頁，編號 1）

本主機板配備 4-Pin

CPU 風扇（靜音風扇）

接頭。若您計畫連接

3-Pin CPU 風扇，請

接至 Pin 1-3。

ATX 電源接頭

(24-pin ATXPWR1)

（請參閱第 1 頁，編號 6）

本主機板配備一組

24-pin ATX 電源接

頭。若要使用 20-pin

ATX 電源供應器，

請插入 Pin 1 及 Pin

13。

ATX 12V 電源接頭

(4-pin ATX12V1)

（請參閱第 1 頁，編號 2）

請將 ATX 12V 電源

供應器連接到這個

接頭。

高解析度音訊支援智慧型音效介面偵測 (Jack Sensing)，但機殼上的面板線必須

支援 HDA 才能正確運作。請依本手冊及機殼手冊說明安裝系統。

若您使用 AC’97 音訊面板，請按照以下步驟安裝至前面板音訊標頭：

A. 將 Mic_IN (MIC) 連接至 MIC2_L。

B. 將 Audio_R (RIN) 連接至 OUT2_R 且將 Audio_L (LIN) 連接至 OUT2_L。

C. 將接地 (GND) 連接至接地 (GND)。

D. MIC_RET 及 OUT_RET 僅供 HD 音訊面板使用。您不需要在 AC’97 音訊面板

上連接。

E. 若要啟動前側麥克風，請前往 Realtek 控制面板中的「FrontMic」標籤調整「錄

音音量」。

FAN_SPEED

FAN_SPEED_CONTROL

+12V

GND

FAN_SPEED

FAN_SPEED_CONTROL

+12V

GND

134

繁體中文

機殼防護標頭

(2-pin CI1)

（請參閱第 1 頁，編號 5）

本主機板支援「機殼

開啟」偵測功能，可

偵測機殼外蓋是否

遭移除。若要使用本

功能，機殼必須採用

機殼防護偵測設計。

TPM 標頭

(17-pin TPMS1)

（請參閱第 1 頁，編號 7）

此接頭支援信賴平

台模組 (TPM) 系統，

可確保儲存金鑰、數

位憑證、密碼及資料

的安全。TPM 系統也

能強化網路安全、保

護數位身分並確定平

台完整性。

Signal

GND

SMB_DATA_MAIN

LAD2

LAD1

GND

S_PWRDWN#

SERIRQ#

GND

PCICLK

PCIRST#

LAD3

+3V

LAD0

+3VSB

GND

FRAME

SMB_CLK_MAIN

135

Bahasa Indonesia

H81M-ITX/WiFi

Spesikasi

Platform

• Bentuk dan Ukuran Mini-ITX

• Desain Kapasitor Solid

• PCB Struktur Kaca Kepadatan Tinggi

CPU

• Mendukung Prosesor Intel® Core

i7/i5/i3/Xeon®/Pentium®/

Celeron® Generasi ke-4 Baru, dan ke-4 (Soket 1150)

• Mendukung Teknologi Intel® Turbo Boost 2.0

Chipset

• Intel® H81

Memori

• Teknologi Memori DDR3 Kanal Ganda

• 2 x Slot DDR3 DIMM

• Mendukung DDR3 1600/1333/1066 non-ECC, memori tanpa

buer

• Kapasitas maksimum memori sistem: 16GB

• Mendukung Intel® Extreme Memory Prole (XMP)1.3/1.2

Slot Ekspansi

• 1 x Slot PCI Express 2.0 x16

• 1 x Slot Mini-PCI Express Separuh Vertikal: Untuk Modul

WiFi

Gras

• Intel® HD Graphics Built-in Visuals dan output VGA hanya

didukung dengan prosesor yang terintegrasi GPU.

• Mendukung Intel® HD Graphics Built-in Visuals: Intel® Quick

Sync Video dengan AVC, MVC (S3D), dan MPEG-2 Full HW

Encode1, Intel® InTru

3D, Teknologi Intel® Clear Video HD,

Intel® Insider

, Intel® HD Graphics 4400/4600

• Pixel Shader 5.0, DirectX 11.1

• Memori bersama maksimum 1792MB

• Tiga pilihan output VGA: D-Sub, DVI-D, dan HDMI

• Mendukung Tiga Monitor

• Mendukung Teknologi HDMI dengan resolusi maksimum

hingga 1920x1200 @ 60Hz

• Mendukung DVI-D dengan resolusi maksimum hingga

1920x1200 @ 60Hz

• Mendukung D-Sub dengan resolusi maksimum hingga

1920x1200 @ 60Hz

136

Bahasa Indonesia

• Mendukung Auto Lip Sync, Deep Color (12bpc), xvYCC, dan

HBR (High Bit Rate Audio) dengan HDMI (memerlukan

monitor HDMI yang kompatibel)

• Mendukung fungsi HDCP dengan port DVI-D dan HDMI

• Mendukung pemutaran Full HD 1080p Blu-ray (BD) dengan

port DVI-D dan HDMI

Audio

• Audio HD 5.1 CH (Realtek ALC662 Audio Codec)

• Mendukung Perlindungan Lonjakan Arus (ASRock Full

Spike Protection)

• ELNA Audio Caps

LAN

• PCIE x1 Gigabit LAN 10/100/1000 Mb/s

• Realtek RTL8111GR

• Menggunakan Wake-On-WAN

• Menggunakan Wake-On-LAN

• Mendukung Perlindungan Petir/ESD (Perlindungan Penuh

Lonjakan Tegangan ASRock)

• Mendukung Deteksi Kabel LAN

• Mendukung Energy E cient Ethernet 802.3az

• Mendukung PXE

LAN Nirkabel

Modul WiFi-802.11n

• 1T1R 150Mbps IEEE 802.11n / 54Mbps IEEE 802.11g /

11Mbps IEEE 802.11b

• Mendukung mode Stasiun (mode Infrastruktur dan mode

Ad-hoc)

Panel I/O

Belakang

• 1 x Port Mouse/Keyboard PS/2

• 1 x Port D-Sub

• 1 x Port DVI-D

• 1 x Port HDMI

• 4 x Port USB 2.0 (Mendukung Perlindungan ESD

(Perlindungan Penuh Lonjakan Tegangan ASRock))

• 2 x Port USB 3.0 (Mendukung Perlindungan ESD

(Perlindungan Penuh Lonjakan Tegangan ASRock))

• 1 x Port LAN RJ-45 dengan LED (ACT/LINK LED dan

SPEED LED)

• Soket Audio HD: Saluran masuk/Speaker Depan/Mikrofon

137

Bahasa Indonesia

H81M-ITX/WiFi

Penyimpanan

• 2 x Konektor SATA3 6,0 Gb/s, mendukung fungsi NCQ,

AHCI, dan Hot Plug

• 2 x Konektor SATA2 3,0 Gb/s, mendukung fungsi NCQ,

AHCI, dan Hot Plug

Konektor

• 1 x Header Intrusi Chassis

• 1 x Header TPM

• 1 x Konektor kipas CPU (4-pin)

• 1 x Konektor kipas chassis (4-pin)

• 1 x Konektor daya ATX 24 pin

• 1 x Konektor daya 12V 4 pin

• 1 x Konektor audio panel depan

• 2 x Header USB 2.0 (mendukung 4 port USB 2.0) (Mendukung

Perlindungan ESD (ASRock Full Spike Protection))

Fitur BIOS

• 32Mb AMI UEFI Legal BIOS dengan dukungan GUI

Multibahasa

• ACPI 1.1 Kompatibel dengan Aktivitas Pengaktifan

• Dukugan SMBIOS 2.3.1

• Multipengatur Tegangan CPU, DRAM, PCH 1,05V

Perangkat

Keras

Monitor

• Sensor Suhu CPU/Chassis

• Takometer CPU/Chassis Daya

• Kipas Hening CPU/Chassis (Memungkinkan Penyesuaian

Otomatis Kecepatan Kipas Chassis Berdasarkan Suhu CPU)

• Kontrol Multikecepatan Kipas CPU/Chassis

• Deteksi CASE OPEN

• Pemantauan Tegangan: +12V, +5V, +3,3V, CPU Vcore

• Microso® Windows® 8.1 32-bit / 8.1 64-bit / 8 32-bit / 8 64-

bit / 7 32-bit / 7 64-bit

Sertikasi

• FCC, CE, WHQL

• Siap untuk ErP/EuP (memerlukan catu daya untuk ErP/EuP)

* Untuk informasi tentang produk rinci, kunjungi situs web kami: http://www.asrock.com

Contact Information

If you need to contact ASRock or want to know more about ASRock, you’re welcome

to visit ASRock’s website at http://www.asrock.com; or you may contact your dealer

for further information. For technical questions, please submit a support request

form at http://www.asrock.com/support/tsd.asp

ASRock Incorporation

2F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District,

Taipei City 112, Taiwan (R.O.C.)

ASRock EUROPE B.V.

Bijsterhuizen 3151

6604 LV Wijchen

e Netherlands

Phone: +31-24-345-44-33

Fax: +31-24-345-44-38

ASRock America, Inc.

13848 Magnolia Ave, Chino, CA91710

U.S.A.

Phone: +1-909-590-8308

Fax: +1-909-590-1026

ASROCK H81M-ITX/WiFi Manual de usuario

Marca: ASROCK

Modelo: H81M-ITX/WiFi

Tipo: Manual de usuario

Descargar PDF

informe

En otros idiomas

français: ASROCK H81M-ITX/WiFi Manuel utilisateur
italiano: ASROCK H81M-ITX/WiFi Manuale utente
English: ASROCK H81M-ITX/WiFi User manual
Deutsch: ASROCK H81M-ITX/WiFi Benutzerhandbuch
русский: ASROCK H81M-ITX/WiFi Руководство пользователя
português: ASROCK H81M-ITX/WiFi Manual do usuário
日本語: ASROCK H81M-ITX/WiFi ユーザーマニュアル
Türkçe: ASROCK H81M-ITX/WiFi Kullanım kılavuzu

ASROCK H81M-ITX/WiFi Manual de usuario

ASROCK H81M-ITX/WiFi Manual de usuario

En otros idiomas

Documentos relacionados

Otros documentos