Maruyama MD830-1 El manual del propietario

Marca: Maruyama

Modelo: MD830-1

Categoría: Sopladores / secadores de aire

Tipo: El manual del propietario

Lisez et assimilez la totalité de ce manuel avant d'utiliser cet appareil.

Lea y entienda este manual a fondo, antes de usar este aparato.

Mister

Atomizadore

MD830-1

OWNER'S/OPERATOR'S MANUAL

MANUAL DEL PROPIETARIO U OPERADOR

— 1 —

English

TABLE OF CONTENTS

FOREWORD

This Owner’s/Operator’s Manual is designed to familiarize the operator with the various features

and component parts of the equipment and to assist you with the assembly, operation and

maintenance of your new Backpack Mist Blower.

It is essential that any operator of this Backpack Mist Blower product reads and

understands the contents of this manual before using the Backpack Mist Blower.

Important safety instructions will be identified by the following safety symbol:

Failure to comply with the instructions in this manual may result in serious injury or death.

For additional assistance, contact any local authorized Maruyama dealer or Maruyama U.S., Inc.,

4770 Mercantile Drive, suite100, Fort Worth, TX 76137 U.S.A.

phone : 940-383-7400

web : www.maruyama-us.com

MANUAL SAFETY SYMBOLS

Throughout this manual and on the product itself, you will find safety alerts and helpful, information

message preceded by symbols or key words. The following is an explanation of those symbols and

key words and what they mean to you.

Warning label

• Always remove dirt or mud to make the indications legible.

• The following alarm labels are attached.

Alarm label

Foreword ··························································1 Name of each part ·········································12

Safety symbols·················································1 Operating instructions····································15

Warning label ·················································· 1 Regular maintenance···································· 17

Warranty·························································· 2 Storage···························································19

Specifications················································ 11 Emission control information························· 19

Assembly instructions··································· 11

This symbol accompanied by the words WARNING and

DANGER calls attention to an act or condition that can lead

to serious personal injury to operator and bystanders.

Read Owner's/Operator's Manual thoroughly.

Make sure you read the Owner's/Operator's

Manual thoroughly prior to use.

Wear a protector.

Wear protectors such as hat, safety

glasses, ear plugs during work.

Cautions for high temperatures

Muffler of engine, fin of cylinder, etc. are at

high temperatures. Don't touch them.

Prohibition of fire

Don't put a naked flame close to a place

where supplying fuel or doing maintenance.

Cautions for exhaust gas.

Take care not to breathe in exhaust gas

from the engine.

English

— 2 —

Limited Warranty Statement

All Maruyama commercial/ industrial products are warranted to the original purchaser to be free from

defects in material and workmanship from the date of purchase for the time periods listed as follows:

Lifetime solid steel driveshaft and ignition coils.

5 years for qualified IRON 5-YR™commercial,institutional,or industrial use.

1 year for residential or 2 years for commercial use with competitor ’s oil.90 days for rental use.

Engine - Refer to engine manufacturer ’s warranty statement.Maruyama engines are

covered by this limited warranty statement.

This warranty will be in full effect provided the engine is operated for the initial 80 hour

optimization period using Maruyama Premium 2-Stroke oil. After the optimization period the

engine should always be run with either Maruyama Premium 2-Stroke oil or equivalent ISO-L-

EGD & JASO FC 2-Stroke oil.

Any part of a Maruyama product found to be defective within the applicable warranty period shall, at

Maruyama's option, be repaired or replaced without charge. Warranty consideration is obtained by

delivering any Maruyama product believed to be defective to an Authorized Maruyama Servicing Dealer

within the applicable warranty period.

The purchaser shall not be charged for diagnostic labor that leads to the determination that a warranted

part is defective, if the diagnostic work is performed at a Maruyama Dealer.

Any warranted part which is not scheduled for replacement as required maintenance, or which is

scheduled only for regular inspection to the effect of "repair or replace as necessary" shall be warranted

for the warranty period. Any warranted part, which is scheduled for replacement as, required maintenance

shall be warranted for the period of time up to the first scheduled replacement point for that part.

Maruyama Mfg. Co., Inc. is liable for damages to other engine components caused by the failure of a

warranted part still under warranty.

The purchaser is responsible for the performance of the required maintenance, as defined by Maruyama

Mfg. Co., Inc. in the Owner's/Operator's Manual.

EMISSION-RELATED PARTS WARRANTY: In addition to the above warranty coverage, Maruyama

Mfg. Co., Inc. will repair or replace, free of charge, for the original purchaser and each subsequent

purchaser any emission-related part or parts found to be defective in material and workmanship for two

(2) years from original retail delivery date except catalytic converter. Catalytic converter is warranted

one year from original retail delivery date. Emission-related parts are the carburetor assembly, the

ignition coil assembly, the ignition rotor, the spark plug, the catalytic converter and the

fuel tank.

Any replacement part that is equivalent in performance and durability may be used

in non-warranty maintenance or repairs, and shall not reduce the warranty obligations of Maruyama Mfg.

Co., Inc.

This warranty does not cover the following:

1. Maintenance items (excluding defects in materials and workmanship) including hoses, spark plugs,

starter rope, air and fuel filters, clutch shoes, vibration isolators, throttle cables and all cutting

attachments, etc.

2. Extra expenses including shipping and handling, travel, payment for lost time or pay and for any

inconvenience and storage.

3. Alterations or modifications including aftermarket parts not authorized by Maruyama U.S., Inc.

4. Wear, accident, abuse, neglect, misuse, negligence, improper fuels, lubricants, fuel mixtures (when

applicable), or failure to operate or maintain the product in accordance with instructions approved by

Maruyama, repair or replacement as provided under this warranty is the exclusive remedy of the

consumer.

— 3 —

English

Maruyama shall not be liable for any incidental or consequential damages for breach of any express or

implied warranty on these products except to the extent prohibited by applicable law. Any implied

warranty of merchantability or fitness for a particular purpose on these products is limited in duration to

the warranty period as defined in the limited warranty statement. Maruyama reserves the rights to

change or improve the design of the product without notice and does not assume obligation to update

previously manufactured products.

This warranty provides you with specific legal rights, which may vary from state to state.

It is the Owner's and Dealer's responsibility to make sure the Warranty Registration Card is properly filled

out and mailed to Maruyama U.S., Inc. Proof of purchase and registration will be required in order to

obtain warranty service.

To locate an Authorized Maruyama Servicing Dealer nearest you, contact:

Maruyama U.S., Inc.

4770 Mercantile Drive, suite100,

Fort Worth, TX 76137 U.S.A.

940-383-7400

maruyama@maruyama-us.com

www.maruyama-us.com

The engine exhaust from this product

contains chemicals known to the State

of California to cause cancer, birth

defects or other reproductive harm.

WARNING

English

— 4 —

EMISSION CONTROL SYSTEM WARRANTY STATEMENT

This warranty statement outlines the emission warranty coverage provided by Maruyama., U.S. INC. (hereinafter

“Maruyama”) for small off-road engines sold in the U.S. and its territories, as well as the 13 provinces and territories of

Canada. This warranty statement is divided into two parts. Part I warrants that a new Maruyama small off-road engine

complies with U.S. EPA and Environment Canada emissions regulations. Part II warrants that a new Maruyama small off-

road engine certified for sale in California also complies with the State of California’s emissions regulations.

Part I: United States and Canada

Your Warranty Rights and Obligations

Your new small off-road engine must be designed, built and equipped to meet the U.S. EPA emission standards

for small off-road engines with maximum engine power at or below 19 kilowatts or an engine displacement less than 1

liter. Maruyama must warrant the emission control system on your small off-road engine for the period of time listed

below, provided there has been no abuse, neglect, or improper maintenance of your small off-road engine. Where a

warrantable condition exists, Maruyama will repair your small off-road engine at no cost to you including diagnosis, parts,

and labor.

Your emission control system may include such parts as the carburetor or fuel injection system, the ignition

system, and catalytic converter. Also included may be hoses, connectors, and other emission-related assemblies. For a list

of the emission control system parts covered under this warranty, please contact your nearest Maruyama Dealer or contact

Maruyama directly at 1-866-783-7400 or [email protected].

Warranty Coverage

Maruyama warrants to the original retail purchaser, and each subsequent purchaser, that the small off-road

engine, including all parts of its emission control system, is:

1. designed, built, and equipped to conform to the U.S. EPA and Environment Canada emission standards at

the time of sale to the original retail purchaser; and

2. free from defects in materials and workmanship that may keep it from meeting the requirements under these

emission standards.

This warranty begins on the date the small off-road engine is delivered to the original retail purchaser and

extends for a period of five (5) years. This warranty covers all components whose failure would increase the emissions of

any regulated pollutant. This warranty does not cover components whose failure would not increase the engine’s

emissions of any regulated pollutants.

Owner’s Warranty Responsibility

As the small off-road engine owner, you are responsible for the performance of the required maintenance listed

in your owner’s manual. Maruyama recommends that you retain all receipts covering maintenance on your small off-road

engine, but Maruyama cannot deny warranty coverage solely for the lack of receipts or for your failure to ensure the

performance of all scheduled maintenance.

As the small off-road engine owner, you should, however, be aware that Maruyama may deny you warranty

coverage if your small off-road engine or a part has failed due to abuse, neglect, improper maintenance, or unapproved

modifications.

You are responsible for presenting your small off-road engine to a Maruyama dealer as soon as a problem exists.

The emission related warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your emission warranty rights and responsibilities, you should contact:

Maruyama.,U.S. INC.

4770 Mercantile Drive, suite 100

Fort Worth, TX 76137 U.S.A.

Telephone: 1-866-783-7400

Email: [email protected]

— 5 —

English

To Obtain Warranty Service

You must, at your own expense, take your Maruyama small off-road engine or the product on which it is

installed, along with proof of original purchase date, to any Maruyama Dealer who is authorized by Maruyama to sell and

service that Maruyama product during the Dealer’s normal business hours. Claims for repair or adjustments found to be

caused solely by defects in material or workmanship will not be denied because the engine was not properly maintained

and used.

If however, you reside more than 100 miles from an authorized service center in the contiguous states, excluding

certain high-altitude areas, Maruyama will either pay for shipping costs to and from an authorized service center, provide

for a service technician to come to the owner to make the warranty repair, or pay for the repair to be made at a local non-

authorized service center. If you are unable to obtain emission warranty service or are dissatisfied with the warranty

service you received, contact the owner of the dealership involved. However, if you require further assistance, contact

Maruyama directly via the contact information above.

Exclusions

Failures other than those resulting from defects in material or workmanship are not covered by this warranty.

This warranty does not extend to emission control systems and parts that are affected or damaged by owner abuse, misuse,

neglect, improper maintenance or repairs, misfueling, improper storage, collision, the use of unsuitable attachments, or the

unauthorized alteration of any part.

This warranty does not cover replacement of parts or other services and adjustments necessary for required

maintenance at and after the first scheduled replacement point.

Disclaimer of Consequential Damages and Limitation of Implied Warranties

Maruyama., U.S. INC. disclaims responsibility for incidental or consequential damages such as loss of time or

the use of the power equipment, or any commercial loss due to the failure of the equipment; and any implied warranties are

limited to the duration of this written warranty. This warranty is applicable only where the California, U.S. EPA, or

Environment Canada emission control system warranty regulation is in effect.

Part II: CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT

Your Warranty Rights and Obligations

The California Air Resources Board and Maruyama are pleased to explain the emission control system warranty

on your model year 2015/2016 small off-road engine. In California, new small off-road engines must be designed, built,

and equipped to meet the State’s stringent anti-smog standards. Maruyama must warrant the emission control system on

your small off-road engine for the periods of time listed below provided there has been no abuse, neglect or improper

maintenance of your small off-road engine.

Your emission control system may include such parts as the carburetor or fuel injection system, the ignition

system, and catalytic converter. Also included may be fuel tanks, fuel lines, fuel caps, canisters, hoses, belts, connectors,

and other emission-related assemblies.

Where a warrantable condition exists, Maruyama will repair your small off-road engine at no cost to you

including diagnosis, parts and labor.

Manufacturer’s Warranty Coverage

The 1995 and later small off-road engines are warranted for five (5) years. If any emission-related part on your

small off-road engine is defective, the part will be repaired or replaced by Maruyama.

Owner’s Warranty Responsibility

As the small off-road engine owner, you are responsible for the performance of the required maintenance listed

in your owner’s manual. Maruyama recommends that you retain all receipts covering maintenance on your small off-road

engine, but Maruyama cannot deny warranty coverage solely for the lack of receipts or for your failure to ensure the

performance of all scheduled maintenance.

As the small off-road engine owner, you should however be aware that Maruyama may deny you warranty

coverage if your small off-road engine or a part has failed due to abuse, neglect, improper maintenance, or unapproved

modifications.

You are responsible for presenting your small off-road engine to a Maruyama distribution center as soon as a

problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.

English

— 6 —

If you have any questions regarding your warranty rights and responsibilities, you should contact:

Maruyama.,U.S. INC.

4770 Mercantile Drive, suite 100

Fort Worth, TX 76137 U.S.A.

Telephone: 1-866-783-7400

Email: [email protected]

General Emissions Warranty Coverage

Maruyama warrants to the ultimate purchaser and each subsequent purchaser that the small off-road engine is:

1. designed, built, and equipped so as to conform with all applicable regulations adopted by the Air Resources

Board pursuant to its authority in Chapters 1 and 2, Part 5, Division 26 of the Health and Safety Code; and

2. free from defects in materials and workmanship that cause the failure of a warranted part to be identical in

all material respects to the part as described in Maruyama’s application for certification.

The warranty period begins on the date the engine or equipment is delivered to an ultimate purchaser or first

placed into service. The equipment or engine owner will not be charged for diagnostic labor that is directly associated with

diagnosis of a defective, emission-related warranted part, provided that such diagnostic work is performed at a Maruyama

warranty station.

Engine parts outlined in the Periodic Maintenance Chart found in the Owners Manual provided with this engine, are

warranted as follows:

1. Any warranted part that is not scheduled for replacement as required maintenance in the Periodic

Maintenance Chart, is warranted for the warranty period stated above. If any such part fails during the

warranty period, the part will be repaired or replaced by Maruyama at no charge to the owner provided the

repair or replacement is performed at a warranty station. Any such part repaired or replaced under the

warranty will be warranted for the remaining warranty period.

2. Any warranted part that is scheduled only for regular inspection in the Periodic Maintenance Chart is

warranted for the warranty period stated above. Any such part repaired or replaced under warranty will be

warranted for the remaining warranty period.

3. Any warranted part that is scheduled for replacement as required maintenance in the Periodic Maintenance

Chart is warranted for the period of time before the first scheduled replacement date for that part. If the part

fails before the first scheduled replacement, the part will be repaired or replaced by Maruyama at no charge

to the owner provided the repair or replacement is performed at a warranty station. Any such part repaired

or replaced under warranty will be warranted for the remainder of the period prior to the first scheduled

replacement point for the part.

Maruyama is liable for damages to other engine components proximately caused by a failure under warranty of

any warranted part.

Throughout the engine’s warranty period defined above, Maruyama will maintain a supply of warranted parts

sufficient to meet the expected demand for such parts. Any replacement part may be used in the performance of any

warranty maintenance or repairs and will be provided without charge to the owner. Such use will not reduce the warranty

obligations of Maruyama.

Add-on or modified parts, as defined in Section 1900(b)(1) and (b)(10), Title 13, that are not exempted by the

Air Resources Board may not be used. The use of any non-exempted add-on or modified parts by the ultimate purchaser

will be grounds for disallowing a warranty claim made in accordance with this article. Maruyama will not be liable under

this article to warrant failures of warranted parts caused by the use of a non-exempted add-on or modified part.

To Obtain Warranty Service

Notwithstanding the provisions herein, warranty services or repairs will be provided at all Maruyama

distribution centers that are franchised to service the subject engines.

You must, at your own expense, take your Maruyama small off-road engine or the product on which it is

installed, along with proof of original purchase date, to any Maruyama Dealer who is authorized by Maruyama to sell and

service that Maruyama product during the Dealer’s normal business hours. Claims for repair or adjustments found to be

caused solely by defects in material or workmanship will not be denied because the engine was not properly maintained

and used.

If you are unable to obtain emission warranty service or are dissatisfied with the warranty service you received,

contact the owner of the dealership involved. However, if you require further assistance, contact the Maruyama office in

your region:

— 7 —

English

Maruyama.,U.S. INC.

4770 Mercantile Drive, suite 100

Fort Worth, TX 76137 U.S.A.

Telephone: 1-866-783-7400

Email: [email protected]

Exclusions

(1) The repair or replacement of any warranted part otherwise eligible for warranty coverage as stated above

may be excluded from such warranty coverage if Maruyama demonstrates that the engine has been abused,

neglected, or improperly maintained, and that such abuse, neglect, or improper maintenance was the direct

cause of the need for repair or replacement of the part.

(2) Maruyama warrants your engine only for the warranty period specified above.

(3) Except as provided above, any adjustment of a component that has a factory installed, and properly

operating, adjustment limiting device (such as an idle limiter cap or plug) is eligible for warranty coverage as

stated above.

Disclaimer of Consequential Damage and Limitation of Implied Warranties:

Maruyama., U.S. INC. disclaims responsibility for incidental or consequential damages such as loss of time or

the use of the power equipment, or any commercial loss due to the failure of the equipment; and any implied warranties are

limited to the duration of this written warranty. This warranty is applicable only where the California, U.S. EPA, or

Environment Canada emission control system warranty regulation is in effect.

Warranted Parts List:

The following is the emission warranty parts list for your small off-road engine:

(i) Fuel Metering System

(A) Carburetor and internal parts (and/or pressure regulator or fuel injection system)

(B) Cold start enrichment system

(ii) Air Induction System

(A) Intake manifold

(B) Air filter

(iii) Ignition System

(A) Spark plugs

(B) Magneto or electronic ignition system

(D) Ignition coil and/or control module

(iv) Lubrication System

(A) Oil pump and internal parts

(v) Positive Crankcase Ventilation (PCV) System

(A) PCV valve

(B) Oil filler cap

(vi) Catalyst or Thermal Reactor System

(A) Catalytic converter

(B) Exhaust manifold

(vii) Evaporative Emissions System

(A) Fuel tank

(B) Fuel cap

(D) Carbon canister

(E) Purge port connector

(viii) Miscellaneous Items Used in Above Systems

(A) Hoses, clamps, fittings, tubing, sealing gaskets or devices, and mounting hardware

(B) Pulleys, belts and idlers

(D) Electronic Controls

Emissions related parts may vary from model to model. Certain models may not contain all of those parts and certain

models may contain functionally equivalent parts.

Effective 01/01/2015 P/N 99969-6291 (M)

English

— 8 —

FEDERAL EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The U.S. Environmental Protection Agency (EPA) and Maruyama Manufacturing Company, Inc. are pleased to

explain the emission control system warranty on your small off-road engine. New 1997 and later model year small

off-road engines must be designed, built and equipped, at the time of sale, to meet the U.S. EPA regulations for

small off-road engines. The equipment engine must be free from defects in materials and workmanship which

cause it to fail to conform with U.S. EPA standards for the first two years of engine use from the date of sale to the

ultimate purchaser. Maruyama Manufacturing Company, Inc. must warrant the emission control system on your

small off-road engine for the period of time listed above provided there has been no abuse, neglect or improper

maintenance of your small off-road engine.

Emission durability of 300 hours.

Your emission control system may include parts such as the carburetor or fuel injection system, the ignition

system, and catalytic converter. Also included may be hoses, belts, and connectors and other emission related

assemblies.

Where a warrantable condition exists, Maruyama Manufacturing Company, Inc. will repair your small off-road

engine at no cost to you, including diagnosis (if the diagnostic work is performed at an authorized dealer), parts,

and labor.

MANUFACTURER'S WARRANTY COVERAGE:

The 1997 and later model year small off-road engines are warranted for two years. If any emission-related part on

your engine is defective, the part will be repaired or replaced by Maruyama Manufacturing Company, Inc. free of

charge.

OWNER'S WARRANTY RESPONSIBILITIES:

(a) As the small off-road engine owner, you are responsible for the performance of the required maintenance

listed in your owner's manual.

(a) Maruyama Manufacturing Company, Inc. recommends that you retain all receipts covering maintenance on

your small off-road engine, but Maruyama Manufacturing Company, Inc. cannot deny warranty solely for the

lack of receipts or for your failure to ensure the performance of all scheduled maintenance. Any replacement

part or service that is equivalent in performance and durability may be used in non-warranty maintenance or

repairs, and shall not reduce the warranty obligations of the engine manufacturer.

(b) As the small off-road engine owner, you should be aware, however, that Maruyama Manufacturing Company

may deny you warranty coverage if your small off-road engine or a part has failed due to abuse, neglect,

improper maintenance or unapproved modifications.

service center as soon as a problem exists. The warranty repairs should be completed in a reasonable amount

of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should contact Maruyama U.S.,

Inc. at

1-866-783-7400, or [email protected].

COVERAGE

Maruyama Manufacturing Company, Inc. warrants to the ultimate purchaser and each subsequent purchaser that

your small off-road engine will be designed, built and equipped, at the time of sale, to meet all applicable

regulations. Maruyama Manufacturing Company, Inc. also warrants to the initial purchaser and each subsequent

purchaser that your small off-road engine is free from defects in materials and workmanship which cause the

engine to fail to conform with applicable regulations for a period of two years.

The 1997 and later model years, EPA requires manufacturers to small off-road engines for two years. These

warranty periods will begin on the date the small off-road engine is purchased by the initial purchaser. If any

emission-related part on your engine is defective, the part will be replaced by Maruyama Manufacturing Company,

Inc. at no cost to the owner.

Maruyama Manufacturing Company, Inc. shall remedy warranty defects at any authorized Maruyama

Manufacturing Company, Inc. engine dealer or warranty station. Any authorized work done at an authorized

dealer or warranty station shall be free of charge to the owner if such work determines that a warranted part is

defective. Any manufacturer-approved or equivalent replacement part may be used for any warranty maintenance

or repairs on emission-related parts, and must be provided free of charge to the owner if the part is still under

warranty, Maruyama Manufacturing Company, Inc. is liable for damages to other engine components caused by

the failure of a warranted part still under warranty.

EPA considers emission-related warranted parts to include all the parts listed below. These warranted parts are:

the carburetor assembly, the ignition coil assembly, the ignition rotor, the spark plug, the catalytic converter, and

the fuel tank.

English

— 9 —

MAINTENANCE REQUIREMENTS

The owner is responsible for the performance of the required maintenance as defined by the Maruyama

Manufacturing Company, Inc. in the owner's manual.

LIMITATIONS

This Emission Control System Warranty shall not cover any of the following:

(a) repair or replacement required because of misuse or neglect, lack of required maintenance, repairs improperly

performed or replacements not conforming to Maruyama Manufacturing Company, Inc. specifications that

adversely affect performance and/or durability, and alterations or modifications not recommended or approved

in writing by Maruyama Manufacturing Company, Inc., and

(b) replacement of parts and other services and adjustments necessary for required maintenance at and after the

first scheduled replacement point.

CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The California Air Resources Board (CARB), and Maruyama Manufacturing Company, Inc. are pleased to explain

the emission control system warranty on your 2015 small off-road engine. In California, new small off-road

engines must be designed, built and equipped to meet the State's stringent anti-smog standards. Maruyama

Manufacturing Company, Inc. must warrant the emission control system on your small off-road engine for the

period of time listed above provided there has been no abuse, neglect or improper maintenance of your small off-

road engine.

Your emission control system may include parts such as the carburetor or fuel injection system, the ignition

system, fuel tank and catalytic converter. Also included may be hoses, belts, and connectors and other emission

related assemblies.

Where a warrantable condition exists, Maruyama Manufacturing Company, Inc. will repair your small off-road

engine at no cost to you, including diagnosis, parts, and labor.

MANUFACTURER'S WARRANTY COVERAGE:

The 1995 and later small off-road engines are warranted for two years. If any emission-related part on your

engine is defective, the part will be repaired or replaced by Maruyama Manufacturing Company, Inc.

OWNER'S WARRANTY RESPONSIBILITIES:

(a) As the small off-road engine owner, you are responsible for the performance of the required maintenance

listed in your owner's manual.

(a) Maruyama Manufacturing Company, Inc. recommends that you retain all receipts covering maintenance on

your small off-road engine, but Maruyama Manufacturing Company, Inc. cannot deny warranty solely for the

lack of receipts or for your failure to ensure the performance of all scheduled maintenance

(b) As the small off-road engine owner, you should be aware, however, that Maruyama Manufacturing Company

may deny you warranty coverage if your small off-road engine or a part has failed due to abuse, neglect,

improper maintenance or unapproved modifications.

distribution center as soon as a problem exists. The warranty repairs should be completed in a reasonable

amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should contact Maruyama U.S.,

Inc. at

1-866-783-7400, or [email protected].

Emission System Parts

Exhaust Emission Evaporative Emission

Carburetor Fuel Tank

Muffler

Catalytic Converter

Ignition Coil / Magneto

Spark Plug

Air Filter

EGR Valve (piston)

Fuel Filter

— 10 —

English

WARNING

1. Read and understand this Owner's/Operator's Manual before using this product. Be thoroughly familiar with the

proper use of this product.

2. Do not allow children to operate this product. It is not a toy. Never allow adults to operate the unit without first reading

the Owner's / Operator's Manual.

3. Become familiar with the controls and know how to stop the engine quickly.

4. Always use eye protection and hearing protection.

5. Keep the area of operation clear of all persons, particularly small children and pets.

6. Do not point the pipe in the direction of people or pets.

7. Do not operate a product when you are fatigued, sickness, intoxicated, and pregnant.

8. Do not operate a product without proper guards or other protective safety devices in place.

9. Dress properly; do not wear loose clothing or jewelry that can be caught in moving parts. Always wear substantial

footwear, long pant, and long sleeved shirt.

10. Gasoline is highly flammable; handle it carefully.

A. Do not smoke while handling gasoline.

B. Use an approved fuel container for storing the gasoline/oil mixture.

C. Do not fill the fuel tank when the engine is hot or running

D. Fill the fuel tank outdoors and only up to one-half inch from the top of the tank. Do not fill the filler neck.

E. Wipe away any spilled gasoline before starting the engine.

11. Always be sure of your footing; keep a firm hold of the blower pipes, and walk, do not run while operating a mist

blower.

12. Use the correct accessories. Do not use this product for any job except that for which it is intended.

13. Keep all fasteners tight and be sure this product is in safe working condition. Follow the maintenance instructions

provided on page 10 - 11 of this manual.

14. Do not put hands or feet near or under the rotating parts. Keep clear at all times.

15. If this product should start to vibrate abnormally, stop the engine immediately and check for the cause. Vibration is

generally a warning of trouble.

16. Avoid using this product near rocks, gravel, stones and similar matter in order to avoid dangerous flying debris.

17. Use this product only in daylight or good artificial light.

18. Do not allow bystanders in work area.

19. Do not operate in unventilated area.

20. To reduce the risk of injury associated with the inhalation of dust, use a face filter mask in dusty conditions.

21. To reduce the risk of injury associated with contacting rotating part, stop the engine before installing or removing

attachments.

22. To reduce the risk of fire and burn injury:

-Move at least 10ft (3m) away from the fueling point before starting engine.

-Always store gasoline in approved container.

Operating techniques

A. Operate power equipment only at reasonable hours - not early in the morning or late at night when people might be

disturbed. Comply with times listed in local ordinances. Usual recommendations are 9:00 am. to 5:00 p.m., Monday

through Saturday.

B. To reduce noise levels, limit the number of pieces of equipment used at any one time.

C. To reduce noise levels, operate mist blowers at the lowest possible throttle speed to do the job.

D. Check your equipment before operation, especially the muffler, air intakes, and air filters.

E. Use rakes and brooms to loosen debris before blowing.

F. In dusty conditions, slightly dampen surfaces when water is available.

G. Conserve water by using mist blowers instead of hoses for many lawn and garden applications, including areas such

as gutters, screens, patios, grills, porches, and gardens.

H. Watch out for children, pets, open windows, or freshly washed cars, and blow debris safely away.

I. Use the full blower nozzle extension so the air stream can work close to the ground.

J. After using this product and other equipment, CLEAN UP! Dispose of debris in trash receptacles.

— 11 —

English

The MARUYAMA MIST BLOWER comes with an Owner's / Operator's Manual and a Warranty

Registration Card. Assembly and attachment of the throttle lever bracket and blower pipes are

required.

SPECIFICATIONS

Dimensions L x W x H

Dry Weight

Engine Type

Displacement

Ignition System

Carburetor

Chemical Tank Capacity

Fuel Tank Capacity

MD830-1

410 x 475 x 720 mm

11.7 kg

Kawasaki/2-Stroke Air cooled TK65 for EPA

64.7 cc

Electric

All position diaphragm

30 lit

2 lit

Fuel Mixture

50:1

Using MARUYAMA 50:1 2-stroke Engine Oil or any quality 2-stroke engine oil

designed for use in air-cooled, high performance 2-stroke engines.

Flexible Pipe, Swivel Pipe Straight Pipe, Mist PipeAttachiments (Standard)

SERIAL NIMBER

At the Rated Operation (Engine Rotational Speed : 6350 mn-1)

Vibration Value :3.87 m/s

(Shoulder Bearing Part)

Noise emissions Sound power level, measured, dB(A) 108

Sound power level, guaranteed, LWAG dB(A) 109

Safety Inclination Degree is within 10°.

ASSEMBLY INSTRUCTIONS

STEP #1) Locate and identify all the components (see sketch).

STEP #2) Using the BANDS, connect the FLEXIBLE PIPE to the blower, and the SWIVEL PIPE to

the flexible pipe (see sketch).

STEP #3) Assemble the STRAIGHT PIPE, and MIST PIPE, then connect them to the swivel pipe

(see sketch).

STEP #4) Slide handle over swivel pipe and tighten retainer knob. (see sketch).

STEP #5) Connect the Mist hose to the Mist cock and Mist pipe. (see sketch)

BANDS(S)

4.0 in.

FLEXIBLE

PIPE

OWNER'S/

OPERATOR'S

MANUAL

BOX SPANNER

SWIVEL

PIPE

STRAIGHT

PIPE

MIST PIPE

BANDS(S)

3.2 in.

HOSE BAND

HOSE CLAMP X 2 HOSE ASSY DIFFUSION SLIT

Models

OPTION PARTS

MIST DEFLECTOR CAP

DEFRECTOR CAP MIST PIPEMIST PIPEDEFRECTOR CAP

ONE WAY TYPE

DUAL TYPE

WARRANTY

REGISTRATION CARD

— 12 —

English

CHEMICAL TANK

RECOIL STARTER

BLOWER HOUSING

BAND

AIR CLEANER

PRIMER BULB

FUEL TANK

FLEXIBLE PIPE

HOSE BAND

MIST PIPE

SWIVEL PIPE

THROTTLE LEVER

LID

MIST PIPE ASSEMBLE

NAME OF EACH PART

STRAIGHT PIPE

ENGINE

MIST HOSE

HOSE BAND

MIST COCK

SHOULDER STRAP

SERIAL NUMBER

BACK PAD

LEVER BAND

MIST COCK

HOSE CONNECT

MIST HOSE

MIST COCK SETTING PROCEDURE

SET METAL FITTINGS OF "MIST COCK" IN THE

"LEVER BAND".

— 13 —

English

FUEL: MIXING GASOLINE AND OIL

CAUTION! The engine used on this product is of a 2-stroke design. The internal moving parts of the

engine, i.e., crankshaft bearings, piston pin bearings and piston to cylinder wall contact surfaces,

require oil mixed with the gasoline for lubrication. Failure to add oil to the gasoline or failure to mix oil

with the gasoline at the appropriate ratio will cause major engine damage which will void your warranty.

For your fuel premix, only use Maruyama 50:1 2-Stroke Oil or a quality oil designed for 2-stroke air-

cooled engine.

FUEL MIXTURE: When using genuine Maruyama 50:1 2-Stroke Oil, or a quality oil designed for 2-

stroke air-cooled engines, oil ratio is 50 parts gasoline to 1 part oil or 50:1.

CAUTION! If Maruyama brand oil is not used, never use a mixing ratio less than 50:1 regardless of

the oil package mixing instructions. Ratios less the 50:1, reduce the amount of lubrication to the

internal moving parts of the engine and can cause damage.

MIXING INSTRUCTIONS: Always mix fuel and oil in a clean container approved for gasoline.

Mark the container to identify it as fuel mix for the product. Use regular unleaded gasoline and fill

the container with half the required amount of gasoline. Pour the correct amount of oil into the

container then add the remaining amount of gasoline. Close the container tightly and shake it

momentarily to evenly mix the oil and the gasoline before filling the fuel tank on the product.

When refilling the fuel tank, clean around the fuel tank cap to prevent dirt and debris for entering

the tank during cap removal. Always shake the premix fuel container momentarily before filling the

fuel tank.

Always use a spout or funnel when fueling to reduce fuel spillage. Only fill the tank to within 1/2

inch from the top of the tank. Avoid filing to the top of the tank filler neck.

NOTE:

1. Do not mix gasoline and oil directly in the product fuel tank.

CAUTION!

1. Do not use National Marine Manufacturer’s Association (NMMA) or BIA certified oils. This type

or 2-stroke engine oil does not have the proper additives for air-cooled, 2-stroke engines and

can cause engine damage.

2. Do not use automotive motor oil. This type of oil does not have the proper additives for air

cooled, 2-stroke engines and can cause engine damage.

BEFORE OPERATION

GAS GAS

FILL MARK

HALF GASOLINE

ADD OIL

ADD REMAINING

GASOLINE

SHAKE

(MIX OIL AND GASOLINE)

OIL

— 14 —

English

CAUTION!

2.Shutting Engine Off

Before shutting the engine off, allow it to idle for a short

while.

• Never stop the engine by closing the choke.

• Never stop the engine during operation while running

above idle speed.

3.Transporting and Storage

• Shut off the engine and allow it to cool before transporting or storing the unit.

• Do not put the unit on dry grass or near any flammable object unless the engine is cold or cooled

down.

The lowest position of lever is "STOP" setting, and the highest position is the "FULL THROTTLE"

setting.

Be sure the mist blower is correctly assembled and all fasteners and fittings are properly secured.

THROTTLE LEVER

Before operating the mist blower, release the knob, knob the throttle grip to the

position in the illustration, and tighten knob to secure in place.

When the mist blower is strapped to the back of the operator, the throttle lever of

is located on the tube.

THROTTLE

LEVER

HIGH SPEED

IDLE SPEED

STOP

HIGH

KNOB

IDLE

Chemicals

*Read the labels of chemicals to be used carefully and understand the method of use and cautions.

Use the chemicals directly after opening the package. Chemicals left for a long time after the

package is open may cause poor discharging due to moisture absorption.

*Mistaking the discharge quantity re category of chemicals may cause damage.

*Do not leave the chemicals in the chemical tank for a long time. The machine might malfunction.

*Store chemicals in a safe place, and be careful not to break open their containers during

transportation.

*Treat chemical containers to ensure safety.

*Dispose the used chemical or fertilizer bags in a manner that will not cause injury.

*Pay attention to the handling of chemicals and fertilizer. If a chemical enters into eye or mouth, wash it

off with water immediately. If you feel ill, see a doctor immediately.

*According to wind direction, change the discharging method to protect workers and houses. When

discharging chemicals, work from upwind to downwind. Also give consideration to prevent chemicals

from drifting or scattering on crops, enclosures, fish-breeding ponds, and houses nearby.

*When preparing chemicals, prepare the necessary amount only in accordance with the established

spraying plan. If too much chemicals are left over, action is difficult.

— 15 —

English

OPERATING INSTRUCTIONS

STEP #5) Move the "CHOKE LEVER" fully up

ward to the closed position. If the

engine is already warm, only a

partial or open (no choke) choke

setting may be required.

Step#1) Move the “Mist cock” to the closed

position.

PRIMER

BULB

FUEL

RETURN LINE

CHOKE

LEVER

OPEN

STARTER GRIP

HIGH SPEED

IDLE SPEED

STOP

STARTING PROCEDURE

Step#2) Pour chemical into the chemical

tank.

Step#3) Close the lib tightly.

STEP #4) Pump the "PRIMER BULB" under

of the carburetor until fuel can be

seen flowing through the "FUEL-

RETURN LINE".

STEP #6) Set the throttle lever at 1/2 speed.

CAUTION! Pull the "STARTER GRIP" briskly

to start the engine.

NOTE: Only short pulls are necessary. Never

pull the starter cord to its fullest extension.

Never let go of the starter grip until it is at the

fully returned position.

Close the

cover tightly

Do not spill

the liquid

OPEN

STEP #7)

Warming up the engine. When the

engine has started, slowly move the

"CHOKE LEVER" fully upward to the

open position. Allow the engine to

"WARM-UP" at less than 1/2 speed.

If a MARUYAMA engine fails to start after following the above procedures, contact an authorized

MARUYAMA dealer.

— 16 —

English

OPERATION

When the engine has warmed-up, the mist blower can be positioned on the back of the operator.

When the mist blower is positioned and ready for operation, adjust the throttle to a speed required to

accomplish the task.

OPERATING POSITION

INTAKE GRILLE

OF THE BLOWER

HOUSING

2345

Discharging volume

Aperture

(Number on the dial

of volume switch)

The nozzle

being held

nlevel

CAUTION

• Avoid using too dense hydrate solution.

Discharging volume

( /min)

Nozzle holding

position

1. Mist cock 2. Adjustment of discharging volume

• Coincide the number on the dial of

volume switch with the market.

• Discharging volume will increase

accordingly as the number increases.

Volume switch

Open

Stop

mark

— 17 —

English

WARNING

• Never operate a mist blower when you are fatigued.

• Never operate a mist blower without proper guards or other protective safety devices in place.

WARNING

To prevent overheating and engine seizure, cooling air comes from the intake grille of the fan housing

and is pushed by the blower fan through an opening in the fan housing over the cylinder fin area,

taking away combustion heat. The grille and cylinder fins must be kept clean of grass, dust and any

debris. Engine failure due to lack of this "Normal Maintenance" is not covered by warranty.

STOPPING THE ENGINE

Close the Mist cock, and stop spraying.

Always run the engine at idle speed for a few minutes to allow cooling before stopping. To stop the

engine, move the throttle control lever all the way to the engine stop position.

CLEANING THE PRODUCTS

Remove Mist hose from Mist pipe, and discharge chemical from chemical tank.

After recovering the remnant chemical, clean the inside chemical tank using clean water.

Also wash the spray nozzle with clear water.

WASHING

DISCHARGING

MISTCOCK OPEN

DISCHARGING

REGULAR MAINTENANCE

Before each use, the mist blower should be inspected for proper assembly and fitness of all

components. All fasteners should be checked for correct tightness. Always inspect for fuel leaks.

WARNING

Do not attempt to start or operate a mist blower that indicates a fuel leak.

AIR FILTER

The air filter should be inspected each time the mist

blower is used (or more often with extreme conditions).

To inspect, remove the air filter cover and remove the

filter from the case.

Clean air filter(s) by gently tapping element or cleaning

with a suitabe solvent the filter should be completely dry

before using again.

AIR FILTER

(PAPER)

— 18 —

English

SPARK PLUG

The spark plug should be removed from the engine and checked

after each fifty (50) hours of use. The tips can be cleaned with a

stiff brush. Adjust the gap to 0.031 - 0.035 inches (see sketch).

Replace the spark plug if it is oil-fouled or damaged.

CAUTION!

The correct torque for the spark plug is 10 - 12 ft. lbs. Do not over-

tighten.

FUEL FILTER

The fuel filter should be cleaned and inspected for damage after each twenty (20) hours of use.

The fuel filter is attached to the fuel pick-up tube inside the fuel tank. Loosen the clamp and take out

the fuel filter.

To clean the fuel filter, remove it from the fuel tube and wash it with safety solvent. Inspect and clean

the fuel tank before re-installing the fuel filter.

Always replace a defective fuel filter.

TIPS

PROPER GAP

0.031 - 0.035 IN.

FUEL TUBE

GROMMET

FUEL FILTER

CLAMP WEIGHT

FUEL FILTER

COOLING FINS

Free passage of air flow through the cylinder cooling fins is required to prevent poor engine

performance and shortened engine life. Regularly check and clean all debris from the cooling fins by

removing the engine cover (see sketch).

MUFFLER AND EXHAUST PORTS

The muffler should be removed and serviced after each one fifty (50) hours of use. At the same time,

the exhaust ports should be cleaned and inspected. An AUTHORIZED MARUYAMA DEALER should

be contacted for this service.

ENGINE COVER

COOLING FINS

— 19 —

English

GENERAL CLEANING AND TIGHTENING

The MARUYAMA mist blower will provide maximum performance for many hours, if it is maintained

properly. Good maintenance includes regular checking of all fasteners for correct tightness, and cleaning

the entire machine. Contact an authorized MARUYAMA dealer for additional maintenance suggestions.

SPARK ARRESTER

1. Remove the screw from the muffler.

2. Take the spark arrester out off the muffler, and then clean by brushing it.

3. Return the spark arrester to the muffler.

4. Tighten the screw securely.

STORAGE

For long-term storage of the mist blower, first perform all regular maintenance procedures and needed

repairs. Empty the fuel tank. Disconnect the fuel supply line from the carburetor and depress the

primer bulb until fuel stops discharging from the fuel-return line.

Start the engine and allow it to run until it stops. Pull the starter cord a few times to remove any excess

fuel from the engine. Remove the spark plug and insert a small amount of oil into the cylinder. Slowly

pull the starter cord and bring the piston to a position closest to the spark plug hole. Re-install the

spark plug. Apply a thin coating of oil to all the metal surfaces and store the mist blower in a dry place.

EMISSION CONTROL INFORMATION

FUEL INFORMATION

THIS ENGINE IS CERTIFIED TO OPERATE ON UNLEADED REGULAR GRADE GASOLINE ONLY.

A minimum of 87 octane of the antiknock index is recommended.

EMISSION CONTROL INFORMATION

To protect the environment in which we all live, Kawasaki has incorporated an exhaust emission

control system.

EXHAUST EMISSION CONTROL SYSTEM (EM)

The system reduces the amount of pollutants discharged into the atmosphere by the exhaust of this

engine. The fuel, ignition and exhaust systems of this engine have been carefully designed and

constructed to ensure an efficient engine with low exhaust pollutant levels. The exhaust system of the

engine includes a catalytic converter system.

MAINTENANCE AND WARRANTY

Proper maintenance is necessary to ensure that your engine will continue to have low emission levels.

This Owner's/Operator's Manual contains those maintenance recommendations for your engine.

Those items identified by the Periodic Maintenance Chart are necessary to ensure compliance with

the applicable standards.

As the owner of the (Mist Blower, Blower, Trimmer, Hedge Trimmer), you have the responsibility to

make sure that the recommended maintenance is carried out according to the instructions in this

Owner's/Operator's Manual at your own expense.

The Maruyama Limited Emission Control System Warranty requires that you return your

(Mist Blower,Blower, Trimmer, Hedge Trimmer) to an authorized Maruyama (Mist Blower, Blower,

Trimmer, Hedge Trimmer) dealer for remedy under warranty. Please read the warranty carefully, and

keep it valid by complying with the owner's obligations it contains.

SCREW

SPARK

ARRESTER

MUFFLER

— 20 —

English

TAMPERING WITH EMISSION CONTROL SYSTEM PROHIBITED

Federal law and California State law prohibit the following acts or the causing there of:

(1) the removal or rendering inoperative by any person other than for purposes of maintenance, repair,

or replacement, of any device or element of design incorporated into any new engine for the purposes

of emission control prior to its sale or delivery to the ultimate purchaser or while it is in use, or (2) the

use of the engine after such device or element of design has been removed or rendered inoperative by

any person.

Among those acts presumed to constitute tampering are acts listed below:

Do not tamper with the original emission related parts.

• Carburetor and internal parts • Fuel tank

• Spark plug

• Magneto or electronic ignition system

• Fuel filter

• Muffler or any internal portion of the muffler

• Air cleaner element

FUEL RECOMMENDATIONS

FUEL

The Kawasaki TK series 2-stroke engines require a gasoline-oil mixture.

Use only clean, fresh, unleaded regular grade gasoline.

Octane Rating

The octane rating of a gasoline is a measure of its resistance to "knocking".

Use of a minimum of 87 octane of the antiknock index is recommended.

NOTE:

• If "knocking or pinging" occurs, use a different brand of gasoline or higher octane rating.

2-STROKE ENGINE OIL MIXING

Gasoline is extremely flammable and can be explosive under certain conditions.

Turn the engine switch OFF. Do not smoke. Make sure the area is well ventilated and free from any

source of flame of sparks : this includes any appliance with a pilot light.

NOTE:

• Do not mix gasoline and oil directly in the fuel tank.

• The lubricative quality of this mixture deteriorates rapidly.

• Do not use gasoline that has been stored longer than two months.

• To ensure proper starting at low ambient temperatures, fresh winter grade fuel must be used.

CAUTION: The engine is shipped without fuel.

Gasoline is extremely flammable and can be

explosive under certain conditions.

Turn the engine switch OFF. Do not smoke.

Make sure the area is well ventilated and

free from any source of flame of sparks :

this includes any appliance with a pilot light.

WARNING

— 21 —

English

ADJUSTMENT

IDLING SPEED ADJUSTMENT

1. Idle speed is the only available adjustment.

2. Do not tamper with the carburetor setting to increase the maximum engine speed.

3. If adjustment is needed, have it performed by your authorized MARUYAMA service dealer.

Carburetor adjustments are made at the factory and are not adjustable without disassembling the

carburetor.

MAINTENANCE

PERIODIC MAINTENANCE CHART

Note: The service intervals indicated are to be used as a guide. Service to be performed more

frequently as necessary by operating condition.

M: Service to be performed by an authorized Maruyama engine dealer.

★

: Service more frequently under dusty conditions.

Always remove the spark plug cap from

spark plug when servicing the engine to

prevent accidental starting.

WARNING

MAINTENANCE Interval

Daily First Every Every Every

20 hours 20 hours 50 hours 100 hours

Check and replenish fuel

●

Check for fuel leakage

●

Check bolts, nuts and screws

for looseness and loss

●

Clean fuel filter

●

★

Clean air filter element

●

Tighten bolts and nuts

●●

Clean spark plug and adjust electrode gap

●

★

Remove dust and dirt from cylinder fins

●

Remove carbon deposits on piston head

and inside cylinder

●

Remove carbon deposits in the exhaust pipe

of muffler

●

M Clean net of spark arrester (if equipped)

●

Check the sliding portion of crankshaft,

connecting rod etc.

●

Fuel tube It is recommended to replace every 3 years.

Spanish

— 22 —

INDICE

PREFACIO

Este Manual del Propietario u Operador está diseñado para familiarizar al operador con las

diversas características y piezas componentes del equipo, y también para ayudarle con el

armado, la operación y el mantenimiento de su nueva Atomizadore de cargar a la espalda.

Es esencial que todo operador de este producto, Atomizadore de Espalda, lea y entienda el

contenido de este manual antes de usar la Atomizadore de Espalda.

Las instrucciones importantes sobre seguridad se identificarán mediante el siguiente icono:

El no observar las instrucciones de este manual, puede producir lesiones graves o incluso la

muerte.

Para asistencia adicional, póngase en contacto con cualquier distribuidor local autorizado de

Maruyama o con Maruyama U.S., Inc. 4770 Mercantile Drive, suite100, Fort Worth, TX 76137 U.S.A.

Teléfono: 940-383-7400

Página de Internet: www.maruyama-us.com

SIMBOLOS DE SEGURIDAD DEL MANUAL

En este manual y en el producto mismo, usted encontrará alertas de seguridad y útiles mensajes

informativos precedidos por iconos o palabras claves. A continuación una explicación de esos

iconos y de las palabras claves y de lo que significan para usted.

Etiqueta de advertencia

• Limpie la suciedad o el barro de la unidad para que las indicaciones siempre estén legibles.

• Encontrará las siguientes etiquetas de alarma fijadas en la unidad.

Etiquetas de alarma

Prefacio ··························································22 Nombres de las partes ··································26

Etiqueta de advertencia·································22 Instrucciones de Operación···························29

Garantía ························································ 23 Mantenimiento Corriente ······························ 31

Instrucciones de Seguridad···························24 Almacenamiento ············································33

Especificaciones ··········································· 25 Información Sobre Control de Emisiones····· 33

Instrucciones de Armado·······························25

Este icono, acompañado de las palabras ADVERTENCIA y

PELIGRO llama su atención hacia un acto o una condición

que puede conducir a que el operador o quienes están

cerca, sufran lesiones graves.

Lea detenidamente el Manual del Propietario u Operador.

Asegúrese de haber leído completamente el Manual

del Propietario u Operador antes de operar la unidad.

Prevención de incendios.

Nunca maneje combustible o haga mantenimiento

de la unidad cerca de un fuego abierto.

Precauciones con las piezas calientes.

El silenciador del motor, las aletas de cilindro, y otras piezas

de la unidad funcionan a altas temperaturas. No las toque.

SUse elementos de protección.

Use en el trabajo elementos de protección tales como:

casco, gafas de seguridad, tapones para los oídos, etc,.

Precauciones con el gas de escape.

Tenga cuidado de no respirar el gas de

escape del motor de la unidad.

Spanish

— 23 —

Declaración de Garantía Limitada

Todos los productos Maruyama están garantizados al comprador original como libres de defectos en materiales y

mano de obra

desde la fecha de compra y por los períodos de tiempo que se relacionan a continuación:

Lifetime sólidos del eje de transmisión de acero y bobinas de encendido.

5 años para comercial IRON 5-YR™ calificado, institucional, o uso industrial.

1 año para residencial o 2 años para uso commercial con aceite de competidor. 90 días para uso de alquiler.

Motor - Consulte la declaración de garantía del fabricante del motor. Motores Maruyama están cubiertos

por esta declaración de garantía limitada.

Esta garantía estará en pleno efecto considerando que el motor sea operado por el período de optimización de 80

horas usando aceite de 2 tiempos Premium de Maruyama. Después del período de optimización, el motor siempre

debe ser operado con aceite de 2 tiempos Premium de Maruyama o equivalente a aceite de 2 tiempos ISO-L-EGD y

JASO FC 2.

Al comprador no se le cobrará la mano de obra de diagnóstico que conduzca a la determinación del defecto de una

parte garantizada, si el trabajo de diagnóstico lo realiza un distribuidor Maruyama.

Cualquier parte garantizada que no esté programada para reemplazo como mantenimiento requerido, o que esté

programada únicamente para inspección regular con el propósito de "reparar y reemplazar según sea necesario" se

garantizará durante el período de garantía. Cualquier parte garantizada que esté programada para reemplazo como

mantenimiento requerido, se garantizará por el período de tiempo hasta el primer reemplazo programado para esa

parte. Maruyama Mfg. Co. Inc. es responsable por los daños a otros componentes, causados por la falla de una parte

garantizada, todavía bajo garantía.

El comprador es responsable de cumplir con el mantenimiento requerido, según lo define Maruyama Mfg. Co., Inc. en

el Manual del Propietario u Operador.

GARANTIA DE LAS PARTES RELACIONADAS CON EMISION GASES DE ESCAPE : Además del cubrimiento de

la garantía anterior, Maruyama Mfg. Co., Inc. reparará o reemplazará, sin costo alguno para el comprador original y

cada comprador subsiguiente, cualquier parte o partes relacionadas con emisión de gases de escape, que se

encuentren defectuosas en material o mano de obra, durante dos (2) años a partir de la fecha de la entrega original al

detal.

Las partes relacionadas con la emisión son el conjunto del carburador, el conjunto de la bobina de

ignición, el rotor de ignición, la bujía, el convertidor catalítico y el estanque de combustible.

Se puede usar

cualquier repuesto equivalente en desempeño y durabilidad, en reparaciones o mantenimientos no de garantía y ello

no reducirá las obligaciones de garantía de Maruyama Mfg. Co., Inc.

Esta garantía no cubre lo siguiente :

1. Artículos de mantenimiento (excluyendo defectos en materiales y mano de obra) incluyendo mangueras, bujías,

cuerda de arranque, filtros de aire y gasolina, zapatas de embrague, aisladores de vibración, cables del regulador

y todos los aditamentos de corte, etc.

2. Gastos adicionales incluyendo despacho y manejo, transporte, pago por lucro cesante o falta de ingresos o

por cualquier inconveniencia y almacenamiento.

3. Alteraciones o modificaciones incluyendo partes pos mercadeo no autorizadas por Maruyama U.S., Inc.

4. Desgaste, accidente, abuso, descuido, mal uso, negligencia, combustibles, lubricantes, mezclas de combustible

inadecuados (cuando se aplique), o falla en la operación o mantenimiento del producto de acuerdo con las

instrucciones aprobadas por Maruyama.

La reparación o reemplazo según se dispone bajo esta garantía, es el remedio exclusivo del consumidor. Maruyama

no será responsable por ningún daño incidental o consecuencial por violación de cualquier garantía explícita o

implícita en estos productos, excepto en la medida prohibida por la ley. Toda garantía implícita de comerciabilidad o

adecuación para un propósito particular, sobre estos productos está limitada a la duración de los períodos de

garantía, según se definen en la declaración de garantía limitada. Maruyama se reserva el derecho de cambiar o

mejorar el diseño del producto sin aviso y no asume la obligación de actualizar los productos fabricados con

anterioridad. Esta garantía otorga a usted derechos legales específicos, que pueden variar de un estado a otro. Es

responsabilidad del Propietario y del Concesionario, asegurarse de que la Tarjeta de Registro de Garantía sea

adecuadamente llenada y despachada por correo a Maruyama U.S., Inc. Con el objeto de obtener servicio de

garantía, se requerirá prueba de la compra y del registro. Para encontrar un Centro de Servicio Autorizado

Maruyama, contacte Maruyama U.S., Inc. al 1-940-383-7400

Maruyama U.S., Inc.

4770 Mercantile Drive, suite100,

Fort Worth, TX 76137 U.S.A.

Spanish

— 24 —

ADVERTENCIA

1. Antes de usar el atomizador, lea cuidadosamente y entienda a cabalidad este Manual del Propietario u Operador.

Familiarícese a fondo con el uso adecuado del atomizador.

2. Nunca permita que los niños utilicen este atomizador. No es un juguete. Nunca permita que los adultos utilicen el

aparato sin haber leído antes el Manual del Propietario u Operador.

3. Familiarícese con los controles y aprenda cómo apagar el motor rápidamente.

4. Use siempre la protección para los ojos y la protección para los oídos.

5. Mantenga el área de funcionamiento libre de personas, particularmente de niños pequeños y de mascotas.

6. No dirija la boquilla del atomizador hacia personas o mascotas.

7. Nunca utilice un atomizador si usted está fatigado.

8. Nunca utilice un atomizador sin tener puestas o en su lugar, las protecciones adecuadas y los demás dispositivos

de seguridad.

9. Vístase adecuadamente; no use prendas de vestir muy amplias, ni joyas que puedan quedar atrapadas en las

piezas móviles. Siempre use calzado firme, pantalones largos, y camisa de manga larga.

10. La gasolina es altamente inflamable, manéjela cuidadosamente.

A. No fume mientras maneja gasolina.

B. Use un recipiente aprobado para combustibles, para almacenar la mezcla de gasolina y aceite.

C. No llene el depósito de combustible cuando el motor está caliente o en marcha.

D. Llene el depósito de combustible estando en el exterior y únicamente hasta media pulgada antes del borde

superior del depósito. No llene el cuello de llenado.

E. Antes de poner el motor en marcha, limpie la gasolina que se haya derramado.

11. Siempre asegúrese de estar bien calzado; sostenga con firmeza los tubos del atomizador, y camine, nunca corra,

cuando utilice un atomizador.

12. Use los accesorios correctos. No use el atomizador para realizar una labor diferente de aquellas para las cuales se

ha fabricado el atomizador.

13. Mantenga apretados todos los sujetadores y asegúrese de que el atomizador esté en condiciones seguras de

funcionamiento. Observe las instrucciones de mantenimiento que se suministran en las páginas 27 – 29 de este

manual.

14. No ponga las manos ni los pies cerca ni debajo de las piezas giratorias. Manténgase fuera de su alcance en todo

momento.

15. Si el atomizador empezara a vibrar en forma anormal, detenga el motor inmediatamente y revise la unidad para

descubrir la causa. Generalmente la vibración es la señal de un problema.

16. Evite el uso del soplador cerca de rocas, gravilla, piedras y material similar, con el objeto de evitar el peligro de

desechos lanzados.

17. Use el atomizador únicamente a la luz del día o bajo una buena luz artificial.

18. No permita la presencia de personas en el área de trabajo.

19. No utilice sin tener puestas las debidas protecciones.

20. No utilice en un área sin ventilación.

21. Para reducir el riesgo de lesiones asociadas con la inhalación de polvo, bajo condiciones polvorientas use máscara

con filtro facial.

22. Para reducir el riesgo de lesiones, asociadas con contactos con piezas giratorias, detenga el motor antes de

instalar o de remover accesorios.

23. Para reducir el riesgo de incendio y quemaduras:

- Antes de dar arranque al motor, aléjese por lo menos 3 metros del punto de abastecimiento de combustible.

- Siempre almacene la gasolina en un recipiente aprobado.

Técnicas de uso

A. Unicamente utilice el equipo en horas razonables – ni temprano en la mañana ni tarde en la noche, cuando puede

molestar a los demás. Cumpla los horarios que aparecen en las ordenanzas locales. Las recomendaciones usuales

son de 9:00 de la mañana a las 5:00 de la tarde, de lunes a sábado.

B. Para reducir los niveles de ruido, limite el número de piezas de equipo usadas al mismo tiempo.

C. Para reducir los niveles de ruido, utilice los atomizadores a la más baja velocidad posible para realizar el trabajo.

D. Revise su equipo antes de utilizarlo, especialmente el silenciador de ruido, las entradas de aire y los filtros de aire.

E. Use rastrillos y escobas para aflojar los desechos antes de soplar.

F. Bajo condiciones polvorientas, humedezca levemente las superficies o use el accesorio de rocío de neblina cuando

haya agua disponible.

G. Conserve el agua usando las sopladoras en lugar de mangueras y agua lanzada en muchas aplicaciones de

limpieza de césped y jardín, incluyendo áreas tales como cunetas, rejillas, patios, parrillas, porches y jardines.

H. Tenga cuidado con los niños, mascotas, ventanas abiertas, o carros recién lavados, y sople los desechos fijándose

que se alejen sin presentar peligro.

I. Use toda la extensión de la boquilla del soplador de manera que la corriente de aire pueda trabajar cerca del suelo.

J. Después de usar los sopladores y demás equipos, ¡LIMPIELOS! Bote los desechos en receptáculos para la basura.

— 25 —

Spanish

El ATOMIZADOR MARUYAMA viene con un Manual del Propietario u Operador y una Tarjeta de

Registro de Garantía. Se debe montar e instalar la ménsula de la palanca de aceleración y tubos

sopladores.

ESPECIFICAÇÕES

Dimensiones Pr. x An. x Al.

Peso en seco

Tipo de motor

Cilindrada

Sistema de ignición

Carburador

Capacidad del depósito de combustible

MD830-1

410 x 475 x 720 mm

11,7 kg

Kawasaki/2-Tiempos Enfriado al aire TK65 para EPA

64,7 cc

Eléctrico

Diafragma para todas posiciones

30 lit

2,1 galones (2,0 litros)

Mezcla de combustible

50:1

Utilizando aceite de motor de 2 ciclos 50:1 de Maruyama o cualquier otro aceite de motor de 2

ciclos diseñado para uso en motores de 2 ciclos de alto rendimiento, enfriados a aire.

TUBO FLEXIBLE, TUBO ORIENTABLE, TUBO RECTO, TUBO NEBULIZADOR

Accesorios (Estándar)

NUMERO DE SERIE

Bajo funcionamiento nominal (Velocidad rotacional del motor: 6350 mn-1)

Valor de vibración: 3,87 m/s2 (Parte del soporte de hombro)

Emisiones de ruido

Nivel de potencia sonora, medido, dB(A) 108

Nivel de potencia sonora, garantizado, LWAG dB(A) 109

*El grado de inclinación de seguridad está dentro de 10°

INSTRUCCIONES DE MONTAJE

PASO 1) Localice e identifique todos los componentes (vea la figura).

PASO 2) Utilizando las ABRAZADERAS, conecte el TUBO FLEXIBLE al soplador y, a

continuación, el TUBO ORIENTABLE al tubo flexible (vea la figura).

PASO 3) Monte el TUBO RECTO y TUBO NEBULIZADOR y, a continuación, conéctelos al tubo

orientable (vea la figura).

PASO 4) Deslice la palanca sobre el tubo orientable y apriete el botón de retención. (vea la figura)

PASO 5) Conecte la manguera nebulizadora al grifo nebulizador y al tubo nebulizador. (vea la

Modelos

OPCIÓN PARTES

NIEBLA DEFLECTOR PAC

DEFLECTOR TUBO NEBULIZADORTUBO NEBULIZADORDEFLECTOR

TIPO DE UNA

MANERA

TIPO DOBLE

ABRAZADERA(S)

4,0 pulg.

TUBO

FLEXIBLE

MANUAL DEL

PROPIETARIO

U OPERADOR

LLAVE DE TUBO

TUBO

ORIENTABLE

TUBO

RECTO

TUBO

NEBULIZADOR

ABRAZADERA(S)

3,2 pulg.

ABRAZADERA

DE MANGUERA

ABRAZADERA DE MANGUERA X 2

CONJUNTO DE MANGUERA

TARJETA DE

GARANTÍA

REGISTRO

ITSL DIFUSIÓN

— 26 —

Spanish

ESTANQUE QUÍMICO

ARRANCADOR DE REBOBINADO

ALOJAMIENTO DEL SOPLADOR

BANDA

FILTRO DE AIRE

BULBO DE IMPRIMADOR

ESTANQUE DE COMBUSTIBLE

TUBO FLEXIBLE

BANDA DE MANGUERA

TUBO DE ROCÍO

TUBO GIRATORIO

PALANCA DEL ESTRANGULADOR

TAPA

NOMBRES DE LAS PARTES

TUBO RECTO

MOTOR

MANGUERA DE ROCÍO

BANDA

GRIFO DE ROCÍO

CORREA DE HOMBRO

NÚMERO DE SERIE

COJÍN POSTERIOR

BANDA DE PALANCA

GRIFO DE ROCÍO

CONEXIÓN DE MANGUERA

MANGUERA DE ROCÍO

PROCEDIMIENTO DE AJUSTE DEL GRIFO DE ROCÍO

AJUSTE LOS ACCESORIOS METÁLICOS DEL “GRIFO

DE ROCÍO” EN LA “BANDA DE PALANCA”

ENSAMBLE DE TUBO DE ROCÍO

COMBUSTIBLE: MEZCLA DE GASOLINA Y ACEITE

PRECAUCION! Si no usa aceite marca

Maruyama, nunca use una proporción de

mezcla menor de 50:1, sin importar las

instrucciones de mezcla del empaque del

aceite. Las proporciones menores de 50:1

(por ejemplo, 60:1, 80:1, 100:1), reducen la

cantidad de lubricación de las piezas internas

móviles del motor y pueden causar daños.

INSTRUCCIONES DE MEZCLA: Siempre mezcla el combustible y el aceite en un recipiente

limpio, aprobado para gasolina. Marque el recipiente para identificarlo como mezcla de

combustible para Atomizadore de Espalda. Usando gasolina regular sin plomo, llene el recipiente

con la mitad de la cantidad de gasolina que se requiere. Agregue la cantidad correcta de aceite al

recipiente, luego agregue la cantidad restante de gasolina. Cierre el recipiente y agítelo

momentáneamente para mezclar bien el aceite y la gasolina antes de llenar el tanque de la

Atomizadore de Espalda.

Cuando llene de nuevo el tanque de combustible, limpie alrededor de la tapa del tanque para evitar

que mugre y desechos entren al tanque cuando está destapado. Siempre agite

momentáneamente el recipiente con la premezcla de combustible, antes de llenar el tanque.

Use siempre una boquilla o embudo cuando reabastezca el combustible, para reducir las

salpicaduras. Llene el tanque sólo hasta que falte 1/2 pulgada (6 – 12 mm) para llegar al borde. No

llene hasta el final del cuello del tanque.

NOTA:

1. Nunca mezcle gasolina y aceite directamente en el el tanque de la Atomizadore de espalda.

!CUIDADO!

1. No use aceites certificados por la Asociación Nacional de Fabricantes Marinos (NMMA) o BIA.

Estos tipos de aceites para motores de dos ciclos no tienen los aditivos adecuados para

motores de dos ciclos, enfriados por aire y pueden causar daño en el motor.

2. No use aceite motor para automóviles. Este tipo de aceite no tiene los aditivos adecuados

para motores de dos ciclos, enfriados por aire y puede causar daño al motor.

GASOLINA GASOLINA

MARCA DE

LLENADO

1/2 GASOLINA AGREGUE ACEITE AGREGUE EL RESTO

DE LA GASOLINA

AGITE

(MEZCLA DE ACEITE Y GASOLINA)

ACEITE

Gasolina

Aceite 50:1 para 2 Ciclos

1 galón (3,78 litros) 2.6 onzas (76 ml)

2-1/2 galones (9,46 litros)

6.4 onzas (189 ml)

5 galones (18,9 litros) 12.8 onzas (378 ml)

— 27 —

Spanish

— 28 —

Spanish

¡PRECAUCIÓN!

1. Apagado del motor

Antes de apagar el motor, póngalo en marcha al vacío por

un corto tiempo.

• Nunca apague el motor cerrando el regulador de aire.

• Nunca apague el motor mientras esté operando a

velocidad mayor de la de marcha al vacío.

2. Transporte y almacenamiento

• Apague el motor y déjelo enfriar antes de transportar o guardar la unidad.

• No coloque la unidad sobre grama seca o cerca de cualquier material inflamable antes de que el

motor se haya enfriado.

La posición más baja de la palanca de aceleración es la graduación de “MARCHA EN VACIO”, y la

posición más alta es la graduación de “ACELERACIÓN COMPLETA”.

Asegúrese de que el atomizador esté correctamente armado y de que todos los sujetadores y acoples

estén bien asegurados.

PALANCA DE ACELERACIÓN

Antes de utilizar el atomizador, suelte la perilla, haga girar el brazo del

acelerador hasta la posición que se muestra en la ilustración, y apriete la perilla.

PALANCA DE

ACELERACIÓN

ALTA VELOCIDAD

VELOCIDAD DE

MARCHA AL VACÍO

APAGADO

ALTA VELOCIDAD

PERILLA

MARCHA AL VACÍO

Sustancias químicas

*Lea cuidadosamente las etiquetas de los productos químicos que va a utilizar, y entienda bien el

modo de utilización y las precauciones a tomar. Pulverizar por tanque (1000 m2) o equivocarse de

sustancia química puede causar daños.

*Almacene los productos químicos en un lugar seguro, y evite que los contenedores se abran

durante el transporte de los mismos.

*Trate los contenedores o depósitos de manera que garantice seguridad.

*Preste atención a la manipulación de productos químicos. Si algún producto químico le salpica en

ojos o boca, aplique agua inmediatamente.

*Si se encuentra mal, visite un médico de inmediato.

*Cambie el método de pulverización según la dirección del viento, con el fin de proteger a otros

trabajadores y viviendas de los alrededores. Cuando pulverice productos químicos, colóquese de

espaldas al viento. Asimismo, evite que las sustancias químicas se esparzan a cosechas,

cercados, estanques y casas cercanas.

*Cuando pulverice en un invernadero, tenga en cuenta la ventilación del lugar.

*Al preparar las sustancias químicas, prepare únicamente la cantidad necesaria que vaya a utilizar

de acuerdo con el plan de pulverización establecido. El exceso de producto químico dificulta la

acción.

*No pulverice el disolvente. Éste puede causar el fallo de algunas piezas. En caso de que haya

utilizado disolvente en este aparato, limpie a fondo el pulverizador con abundante agua.

— 29 —

Spanish

INSTRUCCIONES DE OPERACIÓN

PASO 5) Desplace la "PALANCA DEL

ESTRANGUDOR" completamente

hacia la posición de cierre. Si el motor

ya está calentado, sólo se requiere un

ajuste parcial o abierto del

estrangulador (sin estrangulación).

PASO 1) Desplace el "Grifo nebulizador" a la

posición de cierre.

BULBO DE

CEBADO

LÍNEA DE RETORNO

DE COMBUSTIBLE

PALANCA DEL

ESTRANGUDOR

CERRAR

ABRIR

ASIDERO DEL ARRANCADOR

ALTA VELOCIDAD

MARCHA LENTA

DETENCIÓN

PROCEDIMIENTO DE ARRANQUE

PASO 2) Vierta el producto químico en el

depósito de producto químico.

PASO 3) Cierra la tapa firmemente.

PASO 4) Bombee el "BULBO DE CEBADO"

por debajo del carburador hasta que

se pueda ver el flujo de combustible

a través de la "LÍNEA DE RETORNO

DE COMBUSTIBLE".

PASO 6) Ajuste la palanca del acelerador a

1/2 velocidad.

¡PRECAUCIÓN! Tire vigorosamente del "ASIDERO

DEL ARRANCADOR" para arrancar el motor.

NOTA: Sólo se requieren tirajes cortos. No tire

nunca del cable del arrancador hasta toda su

extensión. No suelte nunca el asidero del arrancador

hasta que esté completamente en su posición de

retorno.

Cierra la cubierta

firmemente

No derrame el

líquido

ABRIR

PASO 7) Calentamiento del motor. Una vez

que arranque el motor, desplace lentamente

la "PALANCA DEL ESTRANGULADOR"

completamente hacia la posición de abertura.

Permita que el motor "SE CALIENTE" a

menos que 1/2 velocidad.

Si un motor MARUYAMA no arranca después de seguir los procedimientos precedentes, póngase

en contacto con un distribuidor MARUYAMA autorizado.

— 30 —

Spanish

OPERACIÓN

Una vez que el motor esté calentado, se puede posicionar el atomizador en la espalda del operador.

Cuando el atomizador está posicionado y listo para funcionamiento, ajuste el acelerador a la velocidad

necesaria para cumplir la tarea deseada.

POSICIÓN DE OPERACIÓN

REJA DE ADMISIÓN DEL

COMPARTIMIENTO DEL

SOPLADOR

2345

descargando volumen

Numere en el dial

de interruptor de

volumen

El cambio de la

descarga para el

ángulo de tubo.

PRECAUCIÓN

• No use el hidrato de la densidad alta.

descargando

volumen( /min)

ángulo del

tubo

1. Grifo de Rocio 2. El ajuste de descargando volumen

• Coincida el número en el dial de

interruptor de volumen con la marca.

•

Descargando el volumen aumentarán de

acuerdo con como los aumentos del número.

Dial de ajuste

cerca

abra

parad

mark

APAGADO

ALTA VELOCIDAD

MARCHA LENTA

ALTA VELOCIDAD

MARCHA AL VACÍO

GRIFO DE ROCÍO

ADVERTENCIA

• Nunca opere un atomizador cuando esté fatigado.

•

Nunca opere un atomizador sin los protectores apropiados u otros dispositivos de seguridad en posición.

ADVERTENCIA

Para prevenir el sobrecalentamiento y agarrotamiento del motor, el aire de enfriamiento sale de la reja

de admisión del compartimiento del ventilador y se impulsa por el ventilador centrífugo a través de una

abertura en el compartimiento del ventilador sobre el área de las aletas del cilindro, descargando el

calor de combustión. La reja y las aletas del cilindro deben mantenerse libres de césped, polvo y

cualesquiera residuos. Un fallo del motor debido a no observación de este "Mantenimiento Normal" no

está cubierto por la garantía.

APAGADO DEL MOTOR

Cierre el grifo nebulizador y detenga la pulverización. Siempre deje el motor en marcha lenta durante

algunos minutos para permitir que se enfríe antes de apagarlo. Para apagar el motor, desplace la

palanca de mando del acelerador completamente hacia la posición de detención del motor.

LIMPIEZA DE LOS PRODUCTOS

Quite la manguera nebulizadora del tubo nebulizador y, a continuación, descargue el producto químico del depósito de producto

químico. Después recuperar el producto químico remanente, limpie el interior del depósito de producto químico utilizando agua limpia.

Lave también la tobera rociadota con agua limpia.

LAVADO

DESCARGA

GRIFO NEBULIZADOR ABIERTO

DESCARGA

MANTENIMIENTO CORRIENTE

Antes de cada uso, es necesario inspeccionar la sopladora para asegurarse de que esté adecuadamente

armado y todos sus componentes estén firmemente colocados. Revise todos los sujetadores para verificar

que estén correctamente apretados. Siempre revise si hay fugas de combustible.

ADVERTENCIA No intente arrancar u operar una sopladora que muestre fuga de combustible.

FILTRO DE AIRE

El filtro de aire se debe inspeccionar cada vez que se usa la

sopladora (o con más frecuencia bajo condiciones extremas).

Para realizar la inspección, retire la tapa del filtro de aire y

retire el filtro de la caja.

Limpia un filtro (unos filtros) de aire, sacando un elemento

con cuidado o lo limpiando con un solvento apropiado. El filtro

debe ser complemente secado antes de usarlo otra vez.

FILTRO DE AIRE

(PAPEL)

— 31 —

Spanish

BUJÍA

La bujía debe retirarse del motor y revisarse después de cada

cincuenta (50) horas de uso. Los electrodos se pueden limpiar con

un cepillo metálico. Ajuste la tolerancia en 0,8 – 0,9 mm (ver

dibujo). Reemplace la bujía si se ha ensuciado con aceite.

PRECAUCION!

La torsión correcta de la bujía es entre 13,6 y 16,3 Nm. No la

apriete demasiado.

FILTRO DE COMBUSTIBLE

El filtro de combustible se debe limpiar e inspeccionar en busca de daños después de cada veinte (20)

horas de uso. El filtro de combustible está fijado en el tubo de captación, dentro del depósito de

combustible. Afloje la abrazadera y saque el filtro de aire.

Para limpiar el filtro de aire, retírelo del tubo de combustible y lávelo usando la mezcla de combustible

con la que funciona el motor.

Inspeccione y limpie el depósito de combustible antes de volver a instalar el filtro de combustible.

Siempre reemplace un filtro de combustible defectuoso.

ELECTRODOS

TOLERANCIA ADECUADA

DE 0,8 A 0,9 MM

TUBO DE

COMBUSTIBLE

ARO DE

REFUERZO

FILTRO DE

COMBUSTIBLE

ABRAZADERA PESO

FILTRO DE

COMBUSTIBLE

ALET

AS DE ENFRIAMIENTO

Se requiere el pasaje libre del flujo de aire a través de las aletas de enfriamiento del cilindro para

prevenir la reducción del rendimiento y el acortamiento de la vida de servicio del motor. Verifique y

limpie regularmente todos los residuos de las aletas de enfriamiento quitando la cubierta del motor

(vea la figura).

SILENCIOSO Y ORIFICIOS DE ESCAPE

Se debe quitar y reparar el silencioso después de cada cincuenta (50) horas de uso. Al mismo tiempo,

se debe limpiar e inspeccionar los orificios de escape. Póngase en contacto con un DISTRIBUIDOR

MARUYAMA AUTORIZADO para este servicio.

CUBIERTA DEL

MOTOR

ALETAS DE

ENFRIAMIENTO

— 32 —

Spanish

— 33 —

Spanish

LIMPIEZA Y APRIETE GENERAL

El atomizador MARUYAMA ofrecerá su rendimiento máximo durante muchas horas, si se realiza el

mantenimiento adecuado. El buen mantenimiento incluye la verificación regular del apriete correcto de

todos los sujetadores y la limpieza de toda la máquina. Póngase en contacto con un distribuidor

MARUYAMA autorizado para sugerencias de mantenimiento adicionales.

PARACHISPAS

1. Quite el tornillo del silenciador.

2. Saque el parachispas del silenciador y a continuación límpielo

cepillándolo.

3. Instale de nuevo el parachispas en el silenciador.

4. Apretar el tornillo.

ALMACENAJE

Para el almacenaje de largo tiempo del atomizador, primero realice todos los procedimientos del

mantenimiento regular y repare cuando sea necesario. Vacíe el depósito de combustible. Desconecte la

línea de suministro de combustible desde el carburador y presione el bulbo de cebado hasta que se

interrumpa la descarga de combustible desde la línea de retorno de combustible. Arranque el motor y

deje que funcione hasta parar. Tire algunas veces del cable del arrancador para sacar cualquier

combustible remanente del motor. Quite la bujía e inserte una pequeña cantidad de aceite en el cilindro.

Tire lentamente del cable del arrancador y traiga el pistón a la posición más cercana del orificio de la

bujía. Reinstale la bujía. Aplique una capa fina de aceite a todas las superficies metálicas y almacene el

atomizador en un lugar seco.

INFORMACIÓN SOBRE CONTROL DE EMISIONES

INFORMACIÓN SOBRE COMBUSTIBLE

ESTE MOTOR ESTA CERTIFICADO PARA FUNCIONAR UNICAMENTE CON GASOLINA GRADO

CORRIENTE. Se recomienda un mínimo de 87 octanos del índice antidetonante. Este índice

antidetonante aparece fijado en las estaciones de servicio.

INFORMACIÓN SOBRE CONTROL DE EMISIÓN DE GASES DE ESCAPE

Para proteger el Ambiente en el que vivimos todos, Kawasaki tiene incorporado un sistema de control

de emisiones (EM), en cumplimiento de las regulaciones aplicables expedidas por la Junta de

Recursos de Aire de California (California Air Resources Board). Si ha comprado su unidad (Soplador,

Recortadora de Césped, Podadora de Seto) en el Estado de California, el motor tiene una duración

asignada de 300 horas de operación.

SISTEMA DE CONTROL DE EMISIÓN DE GASES DE ESCAPE (EM)

El sistema reduce la cantidad de contaminantes que el escape del motor descarga en la atmósfera.

El combustible, el encendido y los sistemas de escape de este motor han sido cuidadosamente

diseñados y construidos para asegurar un motor eficiente con un nivel bajo de contaminantes en los

gases de escape. Si ha comprado su (Soplador, Recortadora de Césped, Podadora de Seto) en el

estado de California, el sistema de escape del motor incluye un sistema de convertidor catalítico.

TORNILLO

PARACHISPAS

SILENCIADOR

— 34 —

Spanish

MANTENIMIENTO Y GARANTÍA

Es necesario un mantenimiento adecuado para garantizar que su motor continuará teniendo bajos

niveles de emisión. Este Manual del Propietario u Operador. contiene tales recomendaciones de

mantenimiento para su motor. Esos procedimientos, identificados en el Cuadro de Mantenimiento

Periódico, son necesarios para asegurar el cumplimiento de los estándares aplicables.

Como propietario de esta unidad (Soplador, Recortadora de Césped, Podadora de Seto) usted tiene

la responsabilidad de asegurarse de que el mantenimiento recomendado se realiza, a su costo, de

acuerdo con las instrucciones contenidas en este Manual del Propietario u Operador.

La Garantía Limitada Maruyama del Sistema de Control de Emisiones, exige que usted devuelva su

uniddad (Soplador, Recortadora de Césped, Podadora de Seto) a un distribuidor autorizado

Maruyama para que se remedie cualquier defecto bajo garantía. Por favor lea cuidadosamente la

garantía y manténgala válida, y cumpla con las obligaciones de propietario que en ella se detallan.

LA MANIPULACIÓN INDEBIDA DEL SISTEMA DE CONTROL DE EMISIONES ESTÁ PROHIBIDA

La ley del Estado de California prohíbe los actos especificados a continuación, o que se cause

cualquiera de los siguientes hechos: (1) el que cualquier persona, para propósitos diferentes a

mantenimiento, reparación, o reemplazo, retire o deje inoperante cualquier dispositivo o elemento de

diseño incorporado a cualquier motor nuevo para propósitos de control de emisiones, antes de su

venta o entrega al comprador final o mientras tal motor está en uso, o (2) el uso del motor después de

que cualquier persona haya retirado o dejado inoperante tal dispositivo o elemento de diseño.

Los actos relacionados a continuación están entre los actos que se presume constituyen

manipulación indebida:

No manipule indebidamente las piezas originales relacionadas con Tanque de combustible la emisión:

• Carburador y piezas internas • Tanque de combustible

• Bujía

• Magneto o sistema de ignición electrónica

• Filtro de Combustible

• El silenciador ou cualquier otra parte interna del silenciador

• Filtro de aire

RECOMENDACIONES SOBRE COMBUSTIBLE

COMBUSTIBLE

Los motores Kawasaki de 2 tiempos, serie TK requieren mezcla de gasolina – aceite.

Use únicamente gasolina limpia, fresca, sin plomo y de grado corriente.

Grado de Octanaje

El grado de octanaje de una gasolina es la medida de su resistencia a la “detonación”.

Se recomienda usar un octanaje de por lo menos 87, según el índice antidetonante. Este índice

antidetonante se encuentra fijado en las carteleras de las estaciones de servicio.

NOTA:

• Si se presenta “golpeteo o martilleo de válvula”, use una marca diferente de gasolina o gasolina de

más alto octanaje.

La gasolina es extremadamente inflamable y puede ser

explosiva en ciertas condiciones. Gire el interruptor de

arranque del motor a la posición de APAGADO (OFF).

No fume. Asegúrese de que el área esté bien ventilada y

libre de cualquier fuente de llama o chispas: esto incluye

cualquier artefacto de gas con llama piloto.

ADVERTENCIA

— 35 —

Spanish

MEZCLA DE ACEITE PARA EL MOTOR DE 2 TIEMPOS

El aceite se debe mezclar con la gasolina para lubricar el pistón, el cilindro, el cigüeñal, los cojinetes y

los cojinetes de las bielas.

Aceite de Motor Recomendado: aceite formulado para motor de 2 tiempos, enfriado por aire.

Proporción de mezcla de la gasolina y el aceite motor: 1:50 (50 partes de gasolina por 1 parte de

Aceite para Motor de 2 tiempos).

NOTA:

• No mezcle directamente la gasolina y el aceite en el depósito de combustible.

• La calidad lubricante de esta mezcla se deteriora rápidamente.

• No use gasolina que haya estado guardada por más de dos meses.

• Para garantizar un arranque adecuado en ambientes a bajas temperaturas, debe usar combustible

fresco formulado para invierno.

PRECAUCION: El motor se despacha sin combustible.

AJUSTE

AJUSTE DE MARCHA EN VACIO

1. La marcha en vacío es el único ajuste posible.

2. No manipule indebidamente la graduación del carburador para aumentar la velocidad máxima del

motor.

3. Si necesita ajustarlo, hágalo a su comerciante autorizado de servicios de MARUYAMA. El

carburador es ajustado en la fábrica; por lo tanto, no puede hacerlo sin desarmar.

MANTENIMIENTO

CUADRO DE MANTENIMIENTO PERIODICO

Nota: Los intervalos de servicio indicados son para usarse como guía. Se puede dar servicio con más

frecuencia según la necesidad indicada por las condiciones de operación.

M: El servicio lo debe realizar un distribuidor autorizado de motores Maruyama.

★

: Servicio más frecuente bajo condiciones polvorientas.

Siempre retire de la bujía la tapa

cuando dé servicio al motor para evitar

que el motor arranque accidentalmente.

ADVERTENCIA

MANTENIMIENTO Intervalo

Diariamente Primeras Cada Cada Cada

20 horas 20 horas 50 horas 100 horas

Revise y reabastezca el combustible

●

Revise si hay alguna fuga de combustible

●

Revise los pernos, tuercas y tornillos para

asegurarse de que no estén flojos o sueltos

●

Limpie el filtro de combustible

●

★

Limpie el elemento del filtro de aire

●

Apriete los pernos y las tuercas

●●

Limpie la bujía y ajuste la separación de los electrodos

●

★

Limpie el polvo y la mugre acumulados en las aletas del cilindro

●

Remueva los depósitos de carbón en la

cabeza del pistón y dentro del cilindro

●

Remueva los depósitos de carbón del

tubo de salida del silenciador

●

M Limpie la malla del guarda chispas (si lo hay)

●

Revise la porción deslizante del

cigüeñal, la biela, etc.

●

Tubo de combustible Se recomienda reemplazar cada 3 años.

Spanish

— 36 —

Maruyama U.S., Inc.

4770 Mercantile Drive, suite100,

Fort Worth, TX 76137 U.S.A.

Phone 940-383-7400

Fax 940-383-7466

www.maruyama-us.com

P/N 275255-01 15.05 TAP/F

Maruyama MD830-1 El manual del propietario

Marca: Maruyama

Modelo: MD830-1

Categoría: Sopladores / secadores de aire

Tipo: El manual del propietario

Descargar PDF

informe

en otros idiomas

English: Maruyama MD830-1 Owner's manual

Maruyama MD830-1 El manual del propietario

Maruyama MD830-1 El manual del propietario

en otros idiomas

Artículos relacionados

Otros documentos