8 9
EN
Descaling
Please descale your appliance regularly using a high-quality commercial descaling agent. Follow the
manufacturer’s instructions, particularly with regard to the subsequent cleaning with clear water,
which is essential! Suitable descaling agents contain inhibitors that protect appliances against damage
to seals and surfaces, do not cause additional deposits and have no taste. Do not use descaling agents
that are unsuitable for your appliance (such as substances based purely on vinegar or citric acid). Our
warranty does not cover damage caused by using unsuitable descaling agents or failure to follow the
descaling instructions. Please keep descaling agents out of reach of children and make sure you do not
inhale any of the steam given off during descaling.
For UK use only
▪ This product is supplied with a 13 A plug conforming to BS 1363 fitted to the mains lead. If the
plug is unsuitable for your socket outlets or needs to be replaced, please note the following. If the
plug is a non-rewireable one, cut it from the mains lead and immediately dispose of it. Never insert
it into a socket outlet as there is a very great risk of an electric shock.
▪ The replacement of the plug at the mains lead has to be done according to the following instruc-
tions:
Important: The wires in this mains lead are coloured in accordance with the following code:
blue Neutral
brown Live
As the colours of the wires in the mains lead of this
appliance may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
⋅the wire which is coloured blue must be connected to the terminal which is marked with the
letter N or coloured black,
⋅the wire which is coloured brown must be connected to the terminal which is marked with
the letter L or coloured red.
Do not connect any wire to the terminal which is marked
with the letter E or by the earth symbol , or coloured green or green and yellow.
▪ If a 13 A (BS 1363) plug is used it must be fitted with a 13 A fuse conforming to BS 1362 and be
ASTA approved. If any other type of plug is used, the appliance must be protected by a 10 A fuse
either in the plug or adapter or at the distribution board.
If in doubt - consult a qualified electrician.
▪ Never use the plug without closing the fuse cover.
The appliance complies with European directives 2014/35/EU, 2014/30/EU and
2009/125/EU.
At the end of its life, this product may not be disposed of in normal household
waste, but must instead be taken to a collection point for recycling electrical and
electronic appliances.
The materials are recyclable in accordance with their labelling. Reuse, recycling
and other ways of reutilising old appliances make an important contribution to
protecting our environment.
Please ask your local authorities for information about the appropriate disposal
point.
End users are personally responsible for deleting any personal data that may be
stored on appliances they are disposing of.
Subject to change
Initial operation
Clean the inside of the kettle thoroughly before using it for the first time.
To do this, open the lid as shown in the picture.
A strainer in the pouring spout ensures that large pieces of limescale are
filtered out when pouring.
The part of the connection cable which is not required can be wound up
in the base unit.
Connect the mains plug to an earthed socket.
Fill with as much water as needed to be able to see the level on the
water level indicator, although do not go above the Max mark. Close the
lid. Only in this way will the automatic boil-stop function work reliably.
Place the kettle in any position on the base unit. Only after this has been
done can you press downwards on the on/off switch under the handle.
The on/off switch only functions when the kettle is standing on the base
unit.
Do not use the first quantity of boiled water for food preparation.
Automatic switch-off
Shortly after the water has started to boil, the automatic switch-off function will shut down the ket-
tle automatically. If the kettle is filled with only a small quantity of water, the switch-off period will
be increased.
If you require warm but not boiling water, the heating process can be interrupted at any time by
pressing the ON switch. The appliance will then shut down automatically as soon as the kettle is
removed from the base.
For functional reasons, a small amount of condensed water may run out through the openings at
the bottom of the handle and onto the rim of the base. This is due to technical reasons and does not
impair the safety of the appliance.
Safety system
If the kettle is accidentally operated without water, a thermostat protects the kettle from overheating
by switching off the appliance.
Make sure to allow the kettle to cool down before filling with water.
If the first thermostat should fail due to misuse, an additional temperature limiter offers reliable
protection.
Cleaning and maintenance
Disconnect the appliance from the mains and allow it to cool down. Never immerse the appliance in
water; simply wipe it over using a damp cloth with a drop of washing-up liquid and then rub dry.
Do not use harsh or abrasive cleaning agents.
The bottom of the kettle is made of stainless steel. If you notice rust stains all the same, these are only
deposits sticking to the surface. Remove these immediately with a cleaning agent for stainless steel.
The mesh filter in the spout can be pulled off to clean when the lid is open. To remove, press up the
top lug. When inserting, place the mesh filter centrally against the bar and then latch home to the
front.