Alamo Industrial Switchblade Sickle Bar Manual de usuario

Marca: Alamo Industrial

Modelo: Switchblade Sickle Bar

Categoría: Cortadoras de césped

Tipo: Manual de usuario

SWITCHBLADE

5/6

Published 06/19 Part No. 02982612C

OPERATOR’S MANUAL

ALAMO INDUSTRIAL

1502 E. Walnut

Seguin, Texas 78155

830-372-3551

Email: [email protected]

SICKLE BAR

This Operator's Manual is an

integral part of the safe operation of

this machine and must be

maintained with the unit at all times.

READ,

UNDERSTAND, and

FOLLOW the Safety and Operation

Instructions contained in this

manual before operating the

equipment. C01-Cover_A

Important Operating

and Safety

Instructions are found

in the Mower Safety

Video that can be

instantly accessed on

the internet at:

www.algqr.com/ave

To the Owner/Operator/Dealer

All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded

operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has

designed this implement to be used with all its safety equipment properly attached to minimize the chance of

accidents.

BEFORE YOU START! Read the safety messages on the implement and shown in your manual. Observe the rules

of safety and common sense!

WARRANTY INFORMATION:

Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration

Form in full and return it to within 30 Days. Make certain the Serial Number of the Machine is recorded on the

Warranty Card and on the Warranty Form that you retain.

In order to reduce accidents and enhance the safe operation of mowers, Alamo Industrial, in cooperation with other

industry manufacturers has developed the AEM/FEMA Industrial and Agricultural Mower Safety Practices video

and guide book.

The video will familiarize and instruct mower-tractor operators in safe practices when using industrial and

agricultural mowing equipment. It is important that Every Mower Operator

be educated in the operation of their

mowing equipment and be able to recognize the potential hazards that can occur while operating a mower. This

video, along with the mower operator’s manual and the warning messages on the mower, will significantly assist in

this important education.

Your Authorized Alamo Industrial Dealer may have shown this video and presented you a DVD Video when you

purchased your mower. If you or any mower operator have not seen this video, Watch the Video, Read this

Operator’s Manual, and Complete the Video Guidebook before operating your new mower. If you do not

understand any of the instructions included in the video or operator’s manual or if you have any questions

concerning safety of operation, contact your supervisor, dealer or Alamo Industrial.

If you would like a VHS video tape of the video, please email AEMVideo@alamo-group.com or Fax AEM VHS

Video at (830) 372-9529 or mail in a completed copy of the form on the back of this page to AEM VHS Video 1502

E Walnut Street, Seguin, TX 78155. and request the VHS video version. Please include your name, mailing

address, mower model and serial number.

Every operator should be trained for each piece of equipment (Tractor and Mower), Understand the intended use,

and the potential hazards before operating the equipment.

The information and material listed above along with this Operator’s Manual can assist you in meeting the OSHA

requirement for Operator annual training.

OSHA TRAINING REQUIREMENTS

The following training requirements have been taken from Title 29, Code of Federal Regulations Part

1928.57 (a)(6). www.osha.gov

Operator Instructions. At the time of initial assignment and at least annually thereafter, the employer shall instruct

every employee who operates an agricultural tractor or implement in the safe operating practices and servicing of

equipment with which they are or will be involved, and of any other practices dictated by the work environment.

Alamo Industrial will provide

one (1) AEM Mower Safety Practices Video

Please Send Me: VHS Format – AEM/FEMA Mower Operator Safety Video

DVD Format – AEM/FEMA Mower Operator Safety Video

Mower Operator’s Manual

AEM Mower Operator’s Safety Manual

Requester Name:_________________________________Phone:___________________________

Requester Address: ___________________________________________

City:_____________________________________

State: ____________________________________

Zip Code:_________________________________

Mower Model:___________________________Serial Number:_____________________________

Date Purchased:__________________________Dealer Salesperson:_________________________

Dealership Name:________________________ Dealership Location:________________________

Mail to:

AEM Video Services

1502 E. Walnut Street

Seguin, TX 78155

Or Fax to:

(830) 372-9529

Or Email to:

AEMV[email protected]

To the Owner/Operator/Dealer

This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the

implement at all times. A Manual canister is provided on the implement where this manual can be properly stored.

If you lose or damage this manual a free replacement manual can be obtained from an authorized Alamo Industrial

dealer or by down loading the manual from the Alamo Industrial website www.alamo-industrial.com

BEFORE YOU START! READ, UNDERSTAND, and FOLLOW the information provided in this manual, the AEM

Mower Safety manual and the tractor operator's manual carefully to learn how to operate and service your machine

properly. Failure to do so could result in personal injury to you and bystanders. All implements with moving parts

are potentially hazardous. Every effort has been made to ensure that the machine is safe but operators must avoid

engaging in unsafe practices and follow the written instructions provided. The manufacturer has designed this

implement to be used with all its safety equipment properly attached to minimize the chance of accidents.

SAFETY FIRST. Completely read and understand the safety section of this manual before operating this

equipment. Do not allow anyone to operate this equipment who has not fully read and understood this manual.

Contact your Dealer to explain any instructions that you do not fully understand.

The care you give your Alamo Industrial Implement will greatly determine your satisfaction with its performance and

its service life. Carefully read and follow the instructions in this manual to provide you with a thorough

understanding of your new implement and its intended use and service requirements.

All references made in this manual to right, left, front, rear, top or bottom are as viewed facing the direction of

forward travel with the implement properly attached to the tractor.

Replacement Parts information is located in a separate Parts Manual. Alamo Industrial mowers use balanced and

matched system components for blade carriers, blades, cuttershafts, knives, knife hangers, rollers, drivetrain

components, and bearings. These parts are made and tested to Alamo Industrial specifications. Non-genuine “will

fit” parts do not consistently meet these specifications. The use of “will fit” parts may reduce mower performance,

void warranties, and present a safety hazard. Use genuine Alamo Industrial mower parts for economy and safety.

For future reference, record your Alamo Industrial product model number and serial number.

Dealer Telephone Model Number

Owner Purchase Date Serial Number

SERIAL NUMBER PLATE

DEALER to CUSTOMER Pre-Delivery / Operation Instructions

Dealer should inform the Purchaser of this product of Warranty terms, provisions, and procedures that are

applicable. Dealer should also inform the Purchaser to review the contents of the Operator’s Manual including

safety equipment, safe operation and maintenance, to review the Safety Signs on the implement (and tractor if

possible) and of Purchaser’s responsibility to train his/her operators in safe operation procedures.

• IMPLEMENTS: I have explained that Deflectors, Chain Guards, or Solid Skirts must be installed and

maintained in good repair.

• DRIVELINES: I have made certain that all driveline, gearbox, and other shields are in good repair and fastened

securely in place to prevent injuries from entanglement or thrown objects.

• HYDRAULIC MACHINES: I have explained the necessity of using clean hydraulic oil, changing filters as

instructed, stopping leaks, damage caused by operating with over-heated oil, caring for hoses, using hoses of

proper rating, maintaining the specified operating pressure and the potential hazard of oil’s penetrating the

skin.

• FOLDING-TYPE IMPLEMENTS: I have explained that it is not possible to guard against thrown objects when

the head is lifted off ground and that operator is responsible to watch out for persons in the area. I have

explained that the lifted mower head or boom can contact overhead obstructions with damage to cables and

telephone lines and possible injury. I have explained that the extended head or boom or retracted boom can

contact power lines with resulting electrocution, injury or death and that operator is responsible for keeping

clear of such hazards.

PRE-DELIVERY SERVICE

CHECK AND ADJUST OR LUBRICATE AS REQUIRED

See Operator’s Manual for Details

Inspection Performed - Warranty and Safety Procedures Explained - Installation Complete

LUBRICATION & HYDRAULICS



Gearbox (Oil Levels)

 Hydraulic Oil Level (External Tank)

 Tractor Hydraulic Oil Level

 Hydraulic Hoses (Not Kinked Tighten Connections)

 Front Pump Drive (Assembly Is Tight And Shaft Properly

Aligned)

MOWER



Spindle And Motor Bolts Properly Torqued

 Spindle Oil Level

 Blade Carrier Bolts Properly Torqued/Retaining Pin In

Place

 Mower Cutting Height And Level Adjusted

 Cutting Shaft Bearings Lubricated

 All Hardware Properly Torqued

 Tire and Air Pressure/Lug Nuts (Correct Torque)

 Wheel Bearings (Check, Grease, and Preload)

ATTACHMENTS & INSTALLATION



Deflectors Front And Rear

 Shredding Attachments

 Correct Blade Rotation Direction

 Axle Arms And Beams

 Tongue And Control Rods (Installed And Adjusted)

 All Bolts - Pins And Nuts (Proper Torque)

MOWER TO TRACTOR CONNECTIONS



Draw Bar Length (Check And Set)

 A-Frame Pivot & Links

 Control Rods (Adjusted Equal)

 Axle Height (Adjusted)

 Cutting Height (Adjust)

 Mount Kit-Pre-Operation Check Complete

 Mower Wing (Adjust Level With The Center)

 Mower Wing (Check For Proper Raising Operation)

 C.V. Drivelines (Check Max Turn Radius)

 Pull Type Hitch (Height Adjustment)

 Mounting Hardware Properly Torqued

SAFETY ITEMS



Protective Shields (Operation And Installation)

 Driveline Clutch (Torque Limiter) (Adjust And Run In)

 Safety Decals (Installed)

 Operator’s Manual (Supplied)

 Tractor PTO Shield (Installed)

 S.M.V. Emblem (Installed If Needed)

 Tongue Jack (Installation and Operation)

 Safety Tow Chain (Installed)

 ADMA Driveline Safety Manual Supplied

 AEM Mower Safety Manual (Supplied in Canister)

 AEM Mower Safety Video has been shown to Purchaser

TABLE OF CONTENTS

SAFETY SECTION............................................................................................................... 1-1

General Safety Instructions and Practices ........................................................................................................ 1-2

Decal Location ................................................................................................................................................. 1-13

Decal Description ............................................................................................................................................ 1-15

Federal Laws and Regulations ........................................................................................................................ 1-20

INTRODUCTION SECTION ................................................................................................. 2-1

OPERATION SECTION ....................................................................................................... 3-1

OPERATOR REQUIREMENTS ........................................................................................................................ 3-3

TRACTOR REQUIREMENTS ........................................................................................................................... 3-4

ROPS and Seat Belt ...........................................................................................................................................3-4

Tractor Safety Devices .......................................................................................................................................3-4

Tractor Horsepower ............................................................................................................................................3-4

Tractor Hydraulics ..............................................................................................................................................3-5

Front End Weight ...............................................................................................................................................3-5

Power Take Off (PTO) ........................................................................................................................................3-5

GETTING ON AND OFF THE TRACTOR ......................................................................................................... 3-5

Boarding the Tractor ...........................................................................................................................................3-6

Dismounting the Tractor .....................................................................................................................................3-6

STARTING THE TRACTOR .............................................................................................................................. 3-7

PRE-OPERATION INSPECTION AND SERVICE ............................................................................................ 3-8

Tractor Pre-Operation Inspection/Service ..........................................................................................................3-9

Sickle Bar Pre-Operation Inspection/Service .....................................................................................................3-9

DRIVING THE TRACTOR AND IMPLEMENT ................................................................................................ 3-13

Starting the Tractor ...........................................................................................................................................3-14

Brake and Differential Lock Setting ..................................................................................................................3-14

Driving the Tractor and Switch Blade ...............................................................................................................3-15

OPERATING THE TRACTOR AND IMPLEMENT .......................................................................................... 3-16

Position Controls ..............................................................................................................................................3-17

MOTOR CONTROL .........................................................................................................................................3-17

KNIFE SPEED ..................................................................................................................................................3-17

TRACTOR MOWING SPEED ..........................................................................................................................3-18

CUTTER BAR BREAK-BACK ..........................................................................................................................3-18

Operating the Switch Blade ..............................................................................................................................3-19

Shutting Down the Switch Blade ......................................................................................................................3-20

TRANSPORTING THE TRACTOR AND IMPLEMENT ................................................................................... 3-21

Transporting on Public Roadways ..............................................................................................

......................3-22

Hauling the Tractor and Implement ..................................................................................................................3-25

MAINTENANCE SECTION .................................................................................................. 4-1

LUBRICATION INFORMATION ........................................................................................................................ 4-2

INITIAL HYDRAULIC SYSTEM CLEANING ..................................................................................................... 4-3

RESERVOIR OIL & FILTER MAINTENANCE .................................................................................................. 4-3

CUTTERBAR ADJUSTMENTS ......................................................................................................................... 4-4

CUTTERBAR ALIGNMENT .............................................................................................................................. 4-4

GUARD ADJUSTMENT .................................................................................................................................... 4-4

WEAR PLATE ................................................................................................................................................... 4-5

CLIPS ................................................................................................................................................................ 4-5

HYDRAULIC SYSTEM ...................................................................................................................................... 4-7

PUMP & MOTOR ...............................................................................................................................................4-7

VALVES .............................................................................................................................................................4-7

KNIFE REPAIR ..................................................................................................................................................4-7

KNIFE .................................................................................................................................................................4-7

LEDGER PLATES ............................................................................................................................................. 4-8

Cylinder Rod Maintenance ................................................................................................................................ 4-8

Safety Section 1-1

SAFETY SECTION

SAFETY

SB5/6 06/19 Safety Section 1-2

SAFETY

General Safety Instructions and Practices

A careful operator is the best operator. Safety is of primary importance to the manufacturer and should be to

the owner/operator. Most accidents can be avoided by being aware of your equipment, your surroundings, and

observing certain precautions. The first section of this manual includes a list of Safety Messages that, if

followed, will help protect the operator and bystanders from injury or death. Read and understand these Safety

Messages before assembling, operating or servicing this Implement. This equipment should only be operated

by those persons who have read the manual, who are responsible and trained, and who know how to do so

responsibly.

The Safety Alert Symbol combined with a Signal Word, as seen below, is used throughout this

manual and on decals which are attached to the equipment. The Safety Alert Symbol means:

“ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!” The Symbol and Signal Word

are intended to warn the owner/operator of impending hazards and the degree of possible injury

faced when operating this equipment.

Indicates an imminently hazardous situation that, if not avoided, WILL result in DEATH OR

VERY SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, COULD result in DEATH

OR SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, MAY result in MINOR

INJURY.

Identifies special instructions or procedures that, if not strictly observed, could result in

damage to, or destruction of the machine, attachments or the environment.

NOTE: Identifies points of particular interest for more efficient and convenient operation or repair.

(SG-1)

Practice all usual and customary safe working precautions and above all---remember safety is

up to YOU

. Only YOU can prevent serious injury or death from unsafe practices.

READ, UNDERSTAND, and FOLLOW the following Safety Messages. Serious injury or

death may occur unless care is taken to follow the warnings and instructions stated in the

Safety Messages. Always use good common sense to avoid hazards.

(SG-2)

Si no lee ingles, pida ayuda a alguien que si lo lea para que le traduzca las

medidas de seguridad.

(SG-3)

SAFETY

SB5/6 06/19 Safety Section 1-3

SAFETY

Never operate the Tractor or Implement until you have read and

completely understand this Manual, the Tractor Operator’s Manual, and

each of the Safety Messages found in the Manual or on the Tractor and

Implement. Learn how to stop the tractor engine suddenly in an

emergency. Never allow inexperienced or untrained personnel to

operate the Tractor or Implement without supervision. Make sure the

operator has fully read and understood the manuals prior to operation.

(SG-4)

Always maintain the safety signs in good readable condition. If the safety signs are missing,

damaged, or unreadable, obtain and install replacement safety signs immediately.

(SG-5)

Make certain that the “Slow Moving Vehicle” (SMV) sign is installed in

such a way as to be clearly visible and legible. When transporting the

Equipment use the Tractor flashing warning lights and follow all local

traffic regulations.

(SG-6)

Operate this Equipment only with a Tractor equipped with an approved roll-

over-protective system (ROPS). Always wear seat belts. Serious injury or even

death could result from falling off the tractor, particularly during a turnover when

the operator could be pinned under the ROPS.

(SG-7)

Do not modify or alter this Implement. Do not permit anyone to modify or alter this

Implement, any of its components or any Implement function.

(SG-8)

BEFORE leaving the tractor seat lower the implement, set the parking

brake and/or set the tractor transmission in parking gear, disengage the

PTO, stop the engine, remove the key, and wait for all moving parts to

stop. Place the tractor shift lever into a low range or parking gear to

prevent the tractor from rolling. Never dismount a Tractor that is moving

or while the engine is running. Operate the Tractor controls from the

tractor seat only.

(SG-9)

Never allow children or other persons to ride on the Tractor or Implement.

Falling off can result in serious injury or death.

(SG-10)

SAFETY

SB5/6 06/19 Safety Section 1-4

SAFETY

Never allow children to operate, ride on, or come close to the Tractor or

Implement. Usually, 16-17 year-old children who are mature and

responsible can operate the implement with adult supervision, if they

have read and understand the Operator’s Manuals, been trained in

proper operation of the tractor and Implement, and are physically large

enough to reach and operate the controls easily.

(SG-11)

Do not mount or dismount the Tractor while the tractor is moving. Mount

the Tractor only when the Tractor and all moving parts are completely

stopped.

(SG-12)

Start tractor only when properly seated in the Tractor seat. Starting a

tractor in gear can result in injury or death. Read the Tractor operators

manual for proper starting instructions.

(SG-13)

Never work under the Implement, the framework, or any lifted

component unless the Implement is securely supported or blocked up

to prevent sudden or inadvertent falling which could cause serious

injury or even death.

(SG-14)

Do not operate this Equipment with hydraulic oil or fuel leaking. Oil

and fuel are explosive and their presence could present a hazard. Do

not check for leaks with your hand! High-pressure oil streams from

breaks in the line could penetrate the skin and cause tissue damage

including gangrene. To check for a hose leak, SHUT the unit ENGINE

OFF and remove all hydraulic pressure. Wear oil impenetrable gloves,

safety glasses and use cardboard to check for evidence of oil leaks. If

you suspect a leak, REMOVE the HOSE and have it tested at a Dealer.

If oil does penetrate the skin, have the injury treated immediately by a

physician knowledgeable and skilled in this procedure.

(SG-15)

The operator and all support personnel should wear hard hats, safety

shoes, safety glasses, and proper hearing protection at all times for

protection from injury including injury from items that may be thrown by

the equipment.

(SG-16)

SAFETY

SB5/6 06/19 Safety Section 1-5

SAFETY

PROLONGED EXPOSURE TO LOUD NOISE MAY CAUSE

PERMANENT HEARING LOSS! Tractors with or without an Implement

attached can often be noisy enough to cause permanent hearing loss.

We recommend that you always wear hearing protection if the noise in

the Operator’s position exceeds 80db. Noise over 85db over an

extended period of time will cause severe hearing loss. Noise over 90db

adjacent to the Operator over an extended period of time will cause

permanent or total hearing loss. NOTE: Hearing loss from loud noise

[from tractors, chain saws, radios, and other such sources close to the

ear] is cumulative over a lifetime without hope of natural recovery.

(SG-I7)

Never attempt to lubricate, adjust, or remove material from the Implement while it is in

motion or while tractor engine is running.

(SG-20)

Periodically inspect all moving parts for wear and replace when

necessary with authorized service parts. Look for loose fasteners, worn

or broken parts, and leaky or loose fittings. Make sure all pins have

cotter pins and washers. Serious injury may occur from not maintaining

this machine in good working order.

(SG-21)

Do not put hands or feet near the cutter bar. Blade contact can result

in serious injury. Stay away until all motion has stopped and the

mower is securely blocked up.

(SSM-1)

SAFETY

SB5/6 06/19 Safety Section 1-6

SAFETY

Transport only at speeds where you can maintain control of the

equipment. Serious accidents and injuries can result from operating this

equipment at high speeds. Understand the Tractor and Implement and how it handles

before transporting on streets and highways. Make sure the Tractor steering and brakes

are in good condition and operate properly.

Before transporting the Tractor and Implement, determine the proper transport speeds for

you and the equipment. Make sure you abide by the following rules:

Test the tractor at a slow speed and increase the speed slowly. Apply the Brakes smoothly

to determine the stopping characteristics of the Tractor and Implement. As you increase

the speed of the Tractor the stopping distance increases. Determine the maximum

transport speed not to exceed 20 mph (30 kph) for transporting this equipment.

Test the equipment at a slow speed in turns. Increase the speed through the turn only after

you determine that the equipment can be operated at a higher speed. Use extreme care

and reduce your speed when turning sharply to prevent the tractor and implement from

turning over. Determine the maximum turning speed for you and this equipment before

operating on roads or uneven ground.

Only transport the Tractor and Implement at the speeds which allow you to properly control

the equipment.

Be aware of the operating conditions. Do not operate the Tractor with weak or faulty brakes

or worn tires. When operating down a hill or on wet or rain slick roads, the braking distance

increases: use extreme care and reduce your speed. When operating in traffic always use

the Tractor’s flashing warning lights and reduce your speed. Be aware of traffic around you

and watch out for the other guy.

(SG-19)

Always read carefully and comply fully with the manufacturer’s

instructions when handling oil, solvents, cleansers, and any other

chemical agent.

(SG-22)

Never run the Tractor engine in a closed building or without adequate ventilation. The

exhaust fumes can be hazardous to your health.

(SG-23)

KEEP AWAY FROM ROTATING ELEMENTS to prevent entanglement

and possible serious injury or death.

(SG-24)

Never allow children to play on or around Tractor or Implement. Children can slip or fall off

the Equipment and be injured or killed. Inadvertent contact with controls can cause the

Implement to shift or fall crushing themselves or others.

(SG-25)

SAFETY

SB5/6 06/19 Safety Section 1-7

SAFETY

DO NOT use drugs or alcohol immediately before or while operating the

Tractor and Implement. Drugs and alcohol will affect an operator’s

alertness and coordination and therefore affect the operator’s ability to

operate the equipment safely. Before operating the Tractor or Implement,

an operator on prescription or over-the-counter medication must consult

a medical professional regarding any side effects of the medication that

would hinder their ability to operate the Equipment safely. NEVER

knowingly allow anyone to operate this equipment when their alertness or

coordination is impaired. Serious injury or death to the operator or others

could result if the operator is under the influence of drugs or alcohol.

(SG-27)

Operate the Tractor and/or Implement controls only while properly seated in the Tractor seat

with the seat belt securely fastened around you. Inadvertent movement of the Tractor or

Implement may cause serious injury or death.

(SG-29)

Mow only in conditions where you have clear visibility in daylight or with adequate artificial

lighting. Never mow in darkness or foggy conditions where you cannot clearly see at least

300 feet (90 m) in front and to the sides of the tractor and mower. Make sure that you can

clearly see and identify passersby, steep slopes, ditches, drop-offs, overhead obstructions,

power lines, debris and foreign objects. If you are unable to clearly see these type of items

discontinue mowing.

(SGM-1)

Extreme care should be taken when operating near loose objects such

as gravel, rocks, wire, and other debris. Inspect the area before

mowing. Foreign objects should be removed from the site to prevent

machine damage and/or bodily injury or even death. Any objects that

cannot be removed must be clearly marked and carefully avoided by the

operator. Stop mowing immediately if blades strike a foreign object.

Repair all damage and make certain rotor or blade carrier is balanced

before resuming mowing.

(SGM-05)

Mow at the speed that you can safely operate and control the tractor and mower. The

correct mowing speed depends on terrain condition and grass type, density, and height of

cut. Normal ground speed range is from 2 to 5 mph(3-8 kph). Use slow mowing speeds

when operating on or near steep slopes, ditches, drop-offs, overhead obstructions, power

lines, or when debris and foreign objects are to be avoided.

(SGM-07)

Replace bent or broken blades with new blades. NEVER ATTEMPT TO STRAIGHTEN,

WELD, OR WELD HARDFACING ON BLADES SINCE THIS WILL LIKELY CRACK OR

OTHERWISE DAMAGE THE BLADE WITH SUBSEQUENT FAILURE AND POSSIBLY

CAUSE SERIOUS INJURY FROM THROWN BLADES.

(SGM-10)

SAFETY

SB5/6 06/19 Safety Section 1-8

SAFETY

Relieve hydraulic pressure prior to doing any maintenance or repair work on the Implement.

Place the Mower Head on the ground or securely supported on blocks or stands, disengage

the PTO, and turn off the engine. Push and pull the control Levers or Joystick several times

to relieve pressure prior to starting any maintenance or repair work.

(SBM-6)

Always disconnect the wire leads from the mower valve solenoid

before performing service on the Tractor or Mower. Use caution when

working on the Tractor or Mower. Tractor engine must be stopped

before working on Mower or Tractor. The Mower Blades could

inadvertently be turned on without warning and cause immediate

dismemberment, injury or death.

(SBM-12)

Do not back up with this implement. Backing could damage the machine or its components.

(S3PT-4)

Use extreme care when lowering or unfolding the implement’s wings. Make sure no

bystanders are close by or underneath the wings. Allow ample clearance around the

implement when folding or unfolding the wings. Use extreme caution around buildings or

overhead power lines.

(S3PT-05)

There are obvious and hidden potential hazards in the operation of this Implement as in all

power-driven or pulled equipment. REMEMBER! This machine is often operated in rough

terrain conditions that include tall grass, weeds, gullies, holes, slopes, hidden obstructions

and the like. Serious injury or even death may occur unless care is taken to assure the

safety of the operator and bystanders in the area. Do not operate this machine with anyone

in the immediate area.

(S3PT-07)

This Implement may be wider than the Tractor. Be careful when operating or transporting

this equipment to prevent the Implement from running into or striking sign posts, guard rails,

concrete abutments or other solid objects. Such an impact could cause the Implement and

Tractor to pivot violently resulting in loss of steering control, serious injury, or even death.

Never allow the Implement to contact obstacles.

(S3PT-12)

Never interfere with factory-set hydraulic calibrations. Any change in calibration could

cause a failure of the equipment and may result in injury.

(SBH-13)

Maintain adequate tractor stability to prevent lateral instability and

possible tip-over which could result in serious bodily injury or even

death. Widen the wheel tread and add wheel weights where necessary.

Refer to the mounting instructions or call Customer Service if you need

assistance with Counterweight Procedure.

(SSM-2)

SAFETY

SB5/6 06/19 Safety Section 1-9

SAFETY

Do not operate Mower if excessive vibration exists. In the case of extreme vibration, shut

down the Mower and the Tractor engine and wait until all motion has stopped. Inspect the

Mower to determine the source of the vibration. If any Mower blades are missing or

damaged replace them immediately. Operating the Mower with excessive vibration can

result in component failure and broken objects could be thrown outward. To reduce the

possibility of property damage and personal injury, never allow the Mower to be operated

with excessive vibration.

(SSM-3)

Never leave the mower unattended while the head is in the raised

position. The mower could fall causing serious injury to anyone who

might inadvertently be under the mower.

(SSM-4)

Always keep a careful lookout and use extreme care when working

around overhead obstructions. Never allow the Mower head or boom

within 10 feet of any power line. When working close to overhead

power lines consult your electric company for a safe code of operation.

(SBM-7)

Prolonged operation may cause operator boredom and fatigue affecting safe operation.

Take scheduled work breaks to help prevent these potentially impaired operating

conditions. Never operate the Implement and Tractor in a fatigued or bored mental state

which impairs proper and safe operation.

(SG-32)

Use extreme caution when getting onto the Implement to perform repairs, maintenance and

when removing accumulated material. Only stand on solid flat surfaces to ensure good

footing. Use a ladder or raised stand to access high spots which cannot be reached from

ground level. Slipping and falling can cause serious injury or death.

(SG-33)

Avoid contact with hot surfaces including hydraulic oil tanks, pumps, motors, valves and

hose connections. Relieve hydraulic pressure before performing maintenance or repairs.

Use gloves and eye protection when servicing hot components. Contact with a hot surface

or fluid can cause serious injury from burns or scalding.

(SG-34)

Perform service, repairs and lubrication according to the maintenance section. Ensure the

unit is properly lubricated as specified in the lubrication schedule and all bolts and nuts are

properly torqued. Failure to properly service, repair and maintain this Implement in good

operating condition could cause component failure and possible serious injury or even

death.

(SG-35)

DO NOT operate this Implement on a Tractor that is not properly maintained. Should a

mechanical or Tractor control failure occur while operating, immediately shut down the

Tractor and perform repairs before resuming operation. Serious injury and possible death

could occur from not maintaining this Implement and Tractor in good operating condition.

(SG-36)

SAFETY

SB5/6 06/19 Safety Section 1-10

SAFETY

The rotating parts of this machine have been designed and tested for rugged use.

However, the blades could fail upon impact with heavy, solid objects such as metal guard

rails and concrete structures. Such impact could cause the broken objects to be thrown

outward at very high velocities. To reduce the possibility of property damage, serious

injury, or even death, never allow the cutting blades to contact such obstacles.

(SGM-4)

Follow these guidelines to reduce the risk of equipment and grass fires

while operating, servicing, and repairing the Mower and Tractor:

-Equip the Tractor with a fire extinguisher in an accesible location.

-Do Not operate the Mower on a Tractor with an underframe exhaust.

-Do Not smoke or have an open flame near the Mower and Tractor.

-Do Not drive into burning debris or freshly burnt areas.

-Ensure slip clutches are properly adjusted to prevent excessive slippage and plate heating.

-Never allow clippings or debris to collect near drivelines, slip clutches, and gearboxes.

Periodically shut down the Tractor and Mower and clean clippings and collected debris from

the mower deck.

(SGM-12)

Wear gloves and exercise care when handling blades. Blades are SHARP and can cause

lacerations to hands and other parts of the body if not safely handled.

(SSM-09)

DO NOT weld or repair rotating mower components. Welds and other repairs may cause

severe vibration and/or component failure resulting in part being thrown from the mower

causing serious bodily injury. See your Authorized Dealer for proper repairs.

(SGM-13)

The Mower is designed for certain mowing applications and is rated to cut up to a specific

size vegetation (see Mower Standard Equipment and Specifications). DO NOT use this

mower to cut vegetation above the Mower’s rated capacity or to cut any type of non-

vegetative material. Only operate this Mower on a properly sized and equipped Tractor.

Operating this Mower in an application for which it is not designed and/or operating the

Mower with the wrong size Tractor can cause Mower component damage and equipment

failure resulting in possible serious injury or death.

(SGM-14)

Raise the mower head to the transport position and secure with the retaining pin before

traveling on public roads and when storing the mower in the upright position.

(SSM-05)

DO NOT stand in front of the mower head or perform service while the head is in the break

back position. The mower head could suddenly swing forward causing serious bodily injury.

Relieve all hydraulic pressure and secure the mower in position before performing

maintenance.

(SSM-06)

SAFETY

SB5/6 06/19 Safety Section 1-11

SAFETY

Operating, servicing and maintaining this equipment can expose you to chemicals including

gasoline, diesel fuel, lubricants, petroleum products, engine exhaust, carbon monoxide, and

phthalates, which are known to the State of California to cause cancer and birth defects or

other reproductive harm. To minimize exposure, avoid breathing exhaust, do not idle the

engine except as necessary, service your vehicle in a well-ventilated area and wear gloves

or wash your hands frequently when servicing your vehicle. Battery posts, terminals and

related accessories contain lead and lead compounds, chemicals known to the state of

California to cause cancer, birth defects or other reproductive harm. For more information go

to www.P65Warnings.ca.gov. This website, operated by California's Office of Environmental

Health Hazard Assessment, provides information about these chemicals and how

individuals may be exposed to them.

All Safety Shields, Guards and other safety devices including (but not limited to) -

Deflectors, Steel Guards and Gearbox Shields must be used and maintained in good

working condition. All safety devices should be inspected carefully at least daily for missing

or broken components. Missing, broken, or worn items must be replaced at once to reduce

the possibility of injury or death from thrown objects, entanglement, or blade contact.

(SSM-07)

Only replace the spring assembly as a complete unit. DO NOT attempt to remove or repair

the spring outside the assembly. Only allow a properly trained mechanic to disassemble the

spring assembly. Spring tension when released could cause serious bodily injury.

(SSM-08)

Do not operate the implement while wearing loose fitting clothing. Entanglement of the

clothing with the rotating elements can result in serious injury or even death. Stay clear of

all rotating elements at all times.

(SSP-03)

DO NOT allow any person under a folded wing unless wing is securely

locked up or supported. DO NOT approach the Implement unless the

Tractor is turned off and all motion has ceased. Never work under the

frame work, or any lifted component unless the implement is securely

supported or blocked up. A sudden or inadvertent fall by any of these

components could cause serious injury or even death.

(STI-03)

SAFETY

SB5/6 06/19 Safety Section 1-12

SAFETY

PARTS INFORMATION

Alamo Industrial mowers use balanced and matched system components for blade carriers, blades,

cuttershafts, knives, knife hangers, rollers, drivetrain components, and bearings. These parts are made and

tested to Alamo Industrial specifications. Non-genuine "will fit" parts do not consistently meet these

specifications. The use of “will fit” parts may reduce mower performance, void mower warranties, and present

a safety hazard. Use genuine Alamo Industrial mower parts for economy and safety.

(SPAM-1)

SEE YOUR ALAMO DEALER

In addition to the design and configuration of this Implement, including Safety Signs and Safety Equipment,

hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper

training of personnel involved in the operation, transport, maintenance, and storage of the machine. Refer

also to Safety Messages and operation instruction in each of the appropriate sections of the Tractor and

Equipment Manuals. Pay close attention to the Safety Signs affixed to the Tractor and Equipment.

(SG-18)

SAFETY

SB5/6 06/19 Safety Section 1-13

SAFETY

Decal Location

NOTE: Alamo Industrial supplies safety decals on this product to promote safe operation. Damage to the

decals may occur while in shipping, use, or reconditioning. Alamo Industrial cares about the safety of its

customers, operators, and bystanders, and will replace the safety decals on this product in the field, free of

charge (Some shipping and handling charges may apply). Contact your Alamo Industrial dealer to order

replacement decals.

SAFETY

SB5/6 06/19 Safety Section 1-14

SAFETY

ITEM PART NO. QTY. TYPE DESCRIPTION

1. D630 1 INSTRUCT Service with Universal Hyd Oil

2. 02974997 1 NAME Switch Blade

3. D617 1 WARNING Hydraulic Oil Leak

4. D628 1 DANGER Crushing Hazard & Pinch Points

5. D733 1 WARNING Not A Step

6. NFS 1 SER PLT Serial Number Plate

7. D726 1 INSTRUCT Grease Fitting Inside

8. D734 1 INSTRUCT Lubrication Chart

9. D881 1 DANGER Run Over Hazard

10. D731 1 DANGER Amputation Hazard

11. D725 1 IMPORTANT Blade Clearance

12. D732 1 IMPORTANT Actuate Control Handle to Reset

13. D635 1 WARNING Operate Machine at 540 RPM

14. 03200347 1 REFLECTOR SMV Symbol

15. 00776031 1 ___________ Canister, Parts Manual

16. 02982612C 1 ___________ Switch Blade Operator’s Manual

17. 10058000 3 ___________ Bolt

18. 00017000 3 ___________ Flatwasher

19. 02959924 3 ___________ Locknut

20. D564 1 WARNING Use Genuine Alamo Industrial Parts

SAFETY

SB5/6 06/19 Safety Section 1-15

SAFETY

Decal Description

SAFETY

SB5/6 06/19 Safety Section 1-16

SAFETY

SB5/6 06/19 Safety Section 1-17

SAFETY

SB5/6 06/19 Safety Section 1-18

SAFETY

SB5/6 06/19 Safety Section 1-19

SAFETY

SB5/6 06/19 Safety Section 1-20

SAFETY

FEDERAL LAWS AND REGULATIONS

This section is intended to explain in broad terms the concept and effect of federal laws and regulations concerning

employer and employee equipment operators. This section is not intended as a legal interpretation of the law and

should not be considered as such.

Employer-Employee Operator Regulations

U.S. Public Law 91-596 (The Williams-Steiger Occupational and Health Act of 1970) OSHA

This Act Seeks:

“...to assure so far as possible every working man and woman in the nation safe and healthful working

conditions and to preserve our human resources...”

DUTIES

Sec. 5 (a) Each employer-

(1) shall furnish to each of his employees employment and a place of employment which are free from

recognized hazards that are causing or are likely to cause death or serious physical harm to his employees;

(2) shall comply with occupational safety and health standards promulgated under this Act.

(b) Each employee shall comply with occupational safety and health standards and all rules, regulations and

orders issued pursuant to this Act which are applicable to his own actions and conduct.

OSHA Training Requirements

Title 29, Code of Federal Regulations Part 1928.57(a)(6). www.osha.gov

Operator instructions. At the time of initial assignment and at least annually thereafter, the employer shall

instruct every employee who operates an agricultural tractor and implements in the safe operating practices

and servicing of equipment with which they are or will be involved, and of any other practices dictated by the

work environment.

Keep all guards in place when the machine is in operation;

Permit no riders on equipment

Stop engine, disconnect the power source, and wait for all machine movement to stop before servicing,

adjusting, cleaning or unclogging the equipment, except where the machine must be running to be properly

serviced or maintained, in which case the employer shall instruct employees as to all steps and procedures

which are necessary to safely service or maintain the equipment.

Make sure everyone is clear of machinery before starting the engine, engaging power, or operating the

machine.

Employer Responsibilities:

To ensure employee safety during Tractor and Implement operation, it is the employer’s responsibility to:

1. Train the employee in the proper and safe operation of the Tractor and Implement.

2. Require that the employee read and fully understand the Tractor and Implement Operator’s manual.

3. Permit only qualified and properly trained employees to operate the Tractor and Implement.

4. Maintain the Tractor and Implement in a safe operational condition and maintain all shields and guards on the

equipment.

5. Ensure the Tractor is equipped with a functional ROPS and seat belt and require that the employee operator

securely fasten the safety belt and operate with the ROPS in the raised position at all times.

6. Forbid the employee operator to carry additional riders on the Tractor or Implement.

7. Provide the required tools to maintain the Tractor and Implement in a good safe working condition and provide the

necessary support devices to secure the equipment safely while performing repairs and service.

8. Require that the employee operator stop operation if bystanders or passersby come within 300 feet.

Child Labor Under 16 Years of Age

Some regulations specify that no one under the age of 16 may operate power machinery. It is your responsibility to

know what these regulations are in your own area or situation.

(Refer to U.S. Dept. of Labor, Employment Standard

Administration, Wage & Home Division, Child Labor Bulletin #102.)

Introduction Section 2-1

INTRODUCTION SECTION

INTRODUCTION

SB5/6 06/19 Introduction Section 2-2

INTRODUCTION

This Switch Blade is designed with care and built with quality materials by skilled workers. Proper assembly,

maintenance, and operating practices, as described in this manual, will help the owner/operator get years of

satisfactory service from the machine.

The purpose of this manual is to familiarize, instruct, and train. The Assembly manual instructs the owner/

operator in the correct assembly of the Mower using standard and optional equipment. The Parts Listing

section is designed to familiarize the owner/operator with replaceable parts on the Mower. This section

provides exploded assembly drawings of each mower component illustrating each piece and the

corresponding part number.

Careful use and timely service saves extensive repairs and costly downtime losses. The Operation and

Maintenance Sections of the manual train the owner/operator how to work the Mower correctly and attend to

appropriate maintenance. The Trouble Shooting Guide helps diagnose difficulties with mower and offers

solution to the problems.

Safety is of primary importance to the owner/operator and to the manufacturer. The first section of this manual

includes a list of Safety Messages, that, if followed, will help protect the operator and bystanders from injury or

death. Many of the Safety Messages will be repeated throughout the manual. The owner/operator/dealer

should know these Safety Messages before assembly and be aware of the hazards of operating this mower

during assembly, use, and maintenance. The Safety Alert Symbol combined with a Signal Word, as seen

below, is intended to warn the owner/operator of impending hazards and the degree of possible injury faced

when operating this machine.

Indicates an imminently hazardous situation that, if not avoided, WILL result in DEATH OR

VERY SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, COULD result in DEATH

OR SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, MAY result in MINOR

INJURY.

Identifies special instructions or procedures that, if not strictly observed, could result in

damage to, or destruction of the machine, attachments or the environment.

INTRODUCTION

SB5/6 06/19 Introduction Section 2-3

INTRODUCTION

The simplistic, time-tested design of the Switch Blade® offers its users a fast, efficient, cost-

effective method of vegetation maintenance. Designed for tractors with smaller horsepower

engines, it is both safe and reliable. Users can depend on the Switch Blade for high

production due to faster cutting as well as less maintenance than any other industrial mower

on the market today.

The Switch Blade cutter bar features a breakaway system allowing the unit to hinge when

obstructed. Also featured is a planetary drive system which allows for smoother operation

and cleaner cutting. An efficient motor, decreased in size and weight, helps to increase

speed control.

With a two-section front pump, the updated hydraulic system allows the unit to run cooler by

eliminating heat, thus running more efficiently. This translates into more cutting power and

less machine maintenance. The Switch Blade's proven blade design allows for precision

cutting. Built-in rock guards help to minimize blade damage.

INTRODUCTION

SB5/6 06/19 Introduction Section 2-4

INTRODUCTION

Attention Owner/Operator

BEORE OPERATING THIS MACHINE:

1. Carefully read the Operator’s Manual, completely understand the Safety Messages and instructions, and

know how to operate correctly both the tractor and implement.

2. Fill out the Warranty Card in full. Be sure to answer all questions, including the Serial Number of the

implement. Mail within 30 days of delivery date of this implement.

NOTE: Warranties are honored only if completed “Owner Registration and Warranty” forms are received by

Alamo Group within thirty days of delivery of the implement.

3. Record the Blade Model and Serial Numbers on the Warranty page at the front of the Operator’s Manual.

Keep this as part of the permanent maintenance file for the implement.

INTRODUCTION

SB5/6 06/19 Introduction Section 2-5

INTRODUCTION

ALAMO-INDUSTRIAL

LIMITED WARRANTY

1. LIMITED WARRANTIES

1.01. Alamo Industrial warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser

(“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”) that the goods purchased

are free from defects in material or workmanship.

1.02. Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be defective under

normal use and service due to defects in material or workmanship.

1.03. This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence,

alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, or which has served

its normal life. This limited warranty does not apply to any part of any internal combustion engine, or expendable items such as

blades, shields, guards, or pneumatic tires except as specifically found in your Operator’s Manual.

1.04. Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any nature on behalf of

Manufacturer.

2. REMEDIES AND PROCEDURES.

2.01. This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer within 30 days

of purchase.

2.02. Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased the goods or an

approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which the claim is based.

2.03. Purchaser is responsible for returning the goods in question to the Dealer.

2.04. If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and service due to

defects in material or workmanship, Manufacturer will:

(a)Repair or replace the defective goods or part(s) or

(b)Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer) if

Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty by

Manufacturer.

The choice of remedy shall belong to Manufacturer.

2.05. Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and for returning the

goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s)

from the Purchaser to the Dealer.

3. LIMITATION OF LIABILITY.

3.01. MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES WITH

RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE.

3.02. MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR USE OF THE

GOODS.

3.03. EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO PURCHASER OR

ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE CAUSED OR ALLEGED TO BE

CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOT LIMITED TO, ANY INDIRECT, SPECIAL,

CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROM THE USE OR OPERATION OF THE GOODS OR ANY

BREACH OF THIS WARRANTY. NOT WITHSTANDING THE ABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER’S

LIABILITY HEREUNDER FOR DAMAGES INCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE

GOODS.

3.04. NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER THIS WARRANTY

MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS OCCURRED.

4. MISCELLANEOUS.

4.01. Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County, Texas.

4.02. Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a

waiver of any other term.

4.03. If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such

provision shall not invalidate any other provisions herein.

4.04. Applicable law may provide rights and benefits to purchaser in addition to those provided herein.

KEEP FOR YOUR RECORDS

ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine identification

when applying for warranty.

Alamo Industrial Implement Model________________________________SerialNumber__________________

Date Purchased______________________________________ Dealer_______________________________

ATTENTION:

READ YOUR OPERATOR'S MANUAL

ALAMO INDUSTRIAL

An Alamo Group Company

Post Office Drawer 549

Seguin, Texas 78156

830-379-1480

Operation Section 3-1

OPERATION SECTION

OPERATION

SB5/6 06/19 Operation Section 3-2

OPERATION

ALAMO INDUSTRIAL SWITCH BLADE SICKLE BAR

OPERATING INSTRUCTIONS

Alamo Industrial Switch Blade are manufactured with quality material by skilled workers. The Switch Blade is

designed for cutting grass and weeds up to 1/2” diameter such as in rights-of-way and roadsides. The Switch

Blade is equipped with safety warning decals, protective guards, shields, and other safety features to provide

operator and passerby protection, however, no shielding is 100% accurate. ALL safety equipment and safety

warning decals must be maintained on the unit in good operational condition at all times.

It is the operator’s responsibility to be knowledgeable of all potential operating hazards and to take every

reasonable precaution to ensure oneself, others, animals, and property are not injured or damaged by the unit,

tractor or a thrown object. Do not operate the unit if bystanders, passersby, pets or livestock are within 300 feet

of the unit.

This section of the Operator’s Manual is designed to familiarize, instruct, and educate operators to the safe and

proper use of the Switch Blade. Pictures contained in this section are intended to be used as a visual aid to

assist in explaining the operation of a Switch Blade and are not specific to a Switch Blade. Some pictures may

show shields removed to enhance visual clarity. NEVER operate the unit without all safety equipment in place

and in good operational condition. The operator must be familiar with the unit and tractor operation and all

safety practices before beginning operation. Proper operation, as detailed in this manual, will help ensure

years of safe and satisfactory use of the Switch Blade.

READ AND UNDERSTAND THE ENTIRE OPERATING INSTRUCTIONS AND SAFETY SECTION OF THIS

MANUAL AND THE TRACTOR MANUAL BEFORE ATTEMPTING TO USE THE TRACTOR AND

IMPLEMENT. If you do not understand any of the instructions, contact your nearest authorized dealer for a

full explanation. Pay close attention to all safety signs and safety messages contained in this manual and

those affixed to the implement and tractor. OPS-U- 0001

READ, UNDERSTAND, and FOLLOW the following Safety Messages. Serious injury or

death may occur unless care is taken to follow the warnings and instructions stated in the

Safety Messages. Always use good common sense to avoid hazards.

(SG-2)

Si no lee ingles, pida ayuda a alguien que si lo lea para que le traduzca las

medidas de seguridad.

(SG-3)

OPERATION

SB5/6 06/19 Operation Section 3-3

OPERATION

1.OPERATOR REQUIREMENTS

Safe operation of the unit is the responsibility of a qualified operator. A qualified operator has read and

understands the implement and tractor Operator’s Manuals and is experienced in implement and tractor

operation and all associated safety practices. In addition to the safety messages contained in this manual,

safety signs are affixed to the implement and tractor. If any part of the operation and safe use of this

equipment is not completely understood, consult an authorized dealer for a complete explanation.

If the operator cannot read the manuals for themselves or does not completely understand the operation of the

equipment, it is the responsibility of the supervisor to read and explain the manuals, safety practices, and

operating instructions to the operator.

Safe operation of equipment requires that the operator wear approved Personal Protective Equipment (PPE)

for the job conditions when attaching, operating, servicing, and repairing the equipment. PPE is designed to

provide operator protection and includes the following safety wear:

PERSONAL PROTECTIVE EQUIPMENT (PPE)

• Always Wear Safety Glasses

•Hard Hat

• Steel Toe Safety Footwear

• Gloves

• Hearing Protection

• Close Fitting Clothing

• Respirator or Filter Mask (depends on

operating conditions) OPS-U- 0002