Alamo Industrial RX60 Manual de usuario

Marca: Alamo Industrial

Modelo: RX60

Categoría: Cortadoras de césped

Tipo: Manual de usuario

Este manual también es adecuado para

RX72
RX84

Published 10/12 Part No. 00785503C

OPERATOR’S MANUAL

ALAMO INDUSTRIAL

1502 E. Walnut

Seguin, Texas 78155

830-372-3551

E-mail: part[email protected]

This Operator's Manual is an

integral part of the safe operation of

this machine and must be

maintained with the unit at all times.

READ,

UNDERSTAND, and

FOLLOW the Safety and Operation

Instructions contained in this

manual before operating the

equipment. C01-Cover_A

Important Operating

and Safety Instructions

are found in the Mower

Safety Video that can

be instantly accessed

on the internet at:

www.algqr.com/ave

$0.00

RX60/72/84

ROTARY MOWER

RX60/72/84

In order to reduce accidents and enhance the safe operation of mowers, Alamo Industrial, in cooperation with

other industry manufacturers has developed the AEM/FEMA Industrial and Agricultural Mower Safety Practices

video and guide book.

The video will familiarize and instruct mower-tractor operators in safe practices when using industrial and

agricultural mowing equipment. It is important that Every Mower Operator

be educated in the operation of their

mowing equipment and be able to recognize the potential hazards that can occur while operating a mower. This

video, along with the mower operator’s manual and the warning messages on the mower, will significantly assist in

this important education.

Your Authorized Alamo Industrial Dealer may have shown this video and presented you a DVD Video when you

purchased your mower. If you or any mower operator have not seen this video, Watch the Video, Read this

Operator’s Manual, and Complete the Video Guidebook before operating your new mower. If you do not

understand any of the instructions included in the video or operator’s manual or if you have any questions

concerning safety of operation, contact your supervisor, dealer or Alamo Industrial.

If you would like a VHS video tape of the video, please e-mail AEMVideo@alamo-group.com or Fax AEM VHS

Video at (830) 372-9529 or mail in a completed copy of the form on the back of this page to AEM VHS Video 1502

E Walnut Street, Seguin, TX 78155. and request the VHS video version. Please include your name, mailing

address, mower model and serial number.

Every operator should be trained for each piece of equipment (Tractor and Mower), Understand the intended use,

and the potential hazards before operating the equipment.

The information and material listed above along with this Operator’s Manual can assist you in meeting the OSHA

requirement for Operator annual training.

OSHA TRAINING REQUIREMENTS

The following training requirements have been taken from Title 29, Code of Federal Regulations Part

1928.57 (a)(6). www.osha.gov

Operator Instructions. At the time of initial assignment and at least annually thereafter, the employer shall instruct

every employee who operates an agricultural tractor or implement in the safe operating practices and servicing of

equipment with which they are or will be involved, and of any other practices dictated by the work environment.

Alamo Industrial Division is willing to provide

one (1) AEM Mower Safety Practices Video

Please Send Me: VHS Format – AEM/FEMA Mower Operator Safety Video

DVD Format – AEM/FEMA Mower Operator Safety Video

Mower Operator’s Manual

AEM Mower Operator’s Safety Manual

Requester Name:_______________________________Phone:___________________________________

Requester Address:_________________________________________

City:_______________________________________

State:______________________________________

Zip Code:___________________________________

Mower Model:____________________________Serial Number:____________________________

Date Purchased:___________________________Dealer Salesperson:_________________________

Dealership Name:_________________________Dealership Location:________________________

Mail to:

AEM Video Services

1502 E. Walnut Street

Seguin, TX 78155

Or Fax to:

(830) 372-9529

Or E-mail to:

AEMV[email protected]

To the Owner/Operator/Dealer

This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the

implement at all times. A Manual canister is provided on the implement where this manual can be properly stored.

If you lose or damage this manual a free replacement manual can be obtained from an authorized Alamo Industrial

dealer or by down loading the manual from the Alamo Industrial website www.www.alamo-industrial.com

BEFORE YOU START! READ, UNDERSTAND, and FOLLOW the information provided in this manual, the AEM

Mower Safety manual and the tractor operator's manual carefully to learn how to operate and service your machine

properly. Failure to do so could result in personal injury to you and bystanders. All implements with moving parts

are potentially hazardous. Every effort has been made to ensure that the machine is safe but operators must avoid

engaging in unsafe practices and follow the written instructions provided. The manufacturer has designed this

implement to be used with all its safety equipment properly attached to minimize the chance of accidents.

SAFETY FIRST. Completely read and understand the safety section of this manual before operating this

equipment. Do not allow anyone to operate this equipment who has not fully read and understood this manual.

Contact your Dealer to explain any instructions that you do not fully understand.

The care you give your Alamo Industrial Implement will greatly determine your satisfaction with its performance and

its service life. Carefully read and follow the instructions in this manual to provide you with a thorough

understanding of your new implement and its intended use and service requirements.

All references made in this manual to right, left, front, rear, top or bottom are as viewed facing the direction of

forward travel with the implement properly attached to the tractor.

Replacement Parts information is located in a separate Parts Manual. Alamo Industrial mowers use balanced and

matched system components for blade carriers, blades, cuttershafts, knives, knife hangers, rollers, drivetrain

components, and bearings. These parts are made and tested to Alamo Industrial specifications. Non-genuine “will

fit” parts do not consistently meet these specifications. The use of “will fit” parts may reduce mower performance,

void warranties, and present a safety hazard. Use genuine Alamo Industrial mower parts for economy and safety.

For future reference, record your Alamo Industrial product model number and serial number.

Dealer Telephone Model Number

Owner Purchase Date: Serial Number

DEALER to CUSTOMER Pre-Delivery/ Operation Instructions

Dealer should inform the Purchaser of this product of Warranty terms, provisions, and procedures that are

applicable. Dealer should inform Purchaser to review the contents of the Operator’s Manual including safety

equipment, safe operation and maintenance, to review the Safety Signs on the implement (and tractor if possible)

and of Purchaser’s responsibility to train his/her operators of safe operation procedures.

• IMPLEMENTS: I have explained that Deflectors, Chain Guards, or Solid Skirts must be installed and

maintained in good repair.

• DRIVELINES: I have made certain that all driveline, gearbox, and other shields are in good repair and

fastened securely in place to prevent injuries from entanglement or thrown objects.

• HYDRAULIC MACHINES: I have explained the necessity of using clean hydraulic oil, changing filters as

instructed, stopping leaks, damage caused by operating with over-heated oil, caring for hoses, using hoses of

proper rating, maintaining the specified operating pressure and the potential hazard of oils penetrating the

skin.

• FOLDING-TYPE IMPLEMENTS: I have explained that it is not possible to guard against thrown objects when

the head is lifted off ground and that operator is responsible to watch out for persons in the area. I have

explained that the lifted mower head or boom can contact overhead obstructions with damage to cables and

telephone lines and possible injury. I have explained that the extended head or boom or retracted boom can

contact power lines resulting in electrocution, injury or death and that operator is responsible for keeping clear

of such hazards.

PRE-DELIVERY SERVICE

CHECK AND ADJUST OR LUBRICATE AS REQUIRED

See Operator’s Manual for Details

Inspection Performed - Warranty and Safety Procedures Explained - Installation Complete

LUBRICATION & HYDRAULICS



Gearbox (Oil Levels)

 Hydraulic Oil Level (External Tank)

 Tractor Hydraulic Oil Level

 Hydraulic Hoses (Not Kinked Tighten Connections)

 Front Pump Drive (Assembly Is Tight And Shaft Properly

Aligned)

MOWER



Spindle And Motor Bolts Properly Torqued

 Spindle Oil Level

 Blade Carrier Bolts Properly Torqued/Retaining Pin In

Place

 Mower Cutting Height And Level Adjusted

 Cutting Shaft Bearings Lubricated

 All Hardware Properly Torqued

 Tire and Air Pressure/Lug Nuts (Correct Torque)

 Wheel Bearings (Check, Grease, and Preload)

ATTACHMENTS & INSTALLATION



Deflectors Front And Rear

 Shredding Attachments

 Correct Blade Rotation Direction

 Axle Arms And Beams

 Tongue And Control Rods (Installed And Adjusted)

 All Bolts - Pins And Nuts (Proper Torque)

MOWER TO TRACTOR CONNECTIONS



Draw Bar Length (Check And Set)

 A-Frame Pivot & Links

 Control Rods (Adjusted Equal)

 Axle Height (Adjusted)

 Cutting Height (Adjust)

 Mount Kit-Pre-Operation Check Complete

 Mower Wing (Adjust Level With The Center)

 Mower Wing (Check For Proper Raising Operation)

 C.V. Drivelines (Check Max Turn Radius)

 Pull Type Hitch (Height Adjustment)

 Mounting Hardware Properly Torqued

SAFETY ITEMS



Protective Shields (Operation And Installation)

 Driveline Clutch (Torque Limiter) (Adjust And Run In)

 Safety Decals (Installed)

 Operator’s Manual (Supplied)

 Tractor PTO Shield (Installed)

 S.M.V. Emblem (Installed If Needed)

 Tongue Jack (Installation and Operation)

 Safety Tow Chain (Installed)

 ADMA Driveline Safety Manual Supplied

 AEM Mower Safety Manual (Supplied in Canister)

 AEM Mower Safety Video has been shown to Purchaser

Table of Contents

SAFETY SECTION ............................................................................................................. 1-1

GENERAL SAFETY INSTRUCTIONS AND PRACTICES ................................................................................ 1-2

OPERATOR SAFETY ....................................................................................................................................... 1-3

CONNECTION OR DISCONNECTING IMPLEMENT SAFETY ....................................................................... 1-4

CRUSHING HAZARDS ..................................................................................................................................... 1-5

THROWN OBJECTS HAZARDS ...................................................................................................................... 1-6

THROWN OBJECTS HAZARDS (CONTINUED) .............................................................................................1-7

RUN OVER HAZARDS ..................................................................................................................................... 1-8

PTO ENTANGLEMENT HAZARDS .................................................................................................................. 1-9

MOWER BLADE CONTACT HAZARDS ........................................................................................................ 1-10

HIGH PRESSURE OIL LEAK HAZARDS ....................................................................................................... 1-11

ELECTRICAL & FIRE HAZARDS ................................................................................................................... 1-12

TRANSPORTING HAZARDS ......................................................................................................................... 1-13

HAZARDS WITH MAINTENANCE OF IMPLEMENT ..................................................................................... 1-14

Decal Location ................................................................................................................................................ 1-16

Decal Description ............................................................................................................................................ 1-18

Federal Laws and Regulations ....................................................................................................................... 1-27

INTRODUCTION SECTION ................................................................................................ 2-1

Equipment Specifications .................................................................................................................................. 2-3

KEY OPERATION POINTS .............................................................................................................................. 2-4

Operating Noise Level/Sound Pressure ............................................................................................................ 2-4

Warranty information ......................................................................................................................................... 2-4

ASSEMBLY SECTION ....................................................................................................... 3-1

DEALER SETUP INSTRUCTIONS ................................................................................................................... 3-2

PULL TYPE (RX84 ONLY) INSTRUCTIONS ................................................................................................... 3-2

SHIELD ASSEMBLY (All Models) ..................................................................................................................... 3-3

TAIL WHEEL INSTALLATION (Model RX60 & RX72) ..................................................................................... 3-3

TAIL WHEEL INSTALLATION - LIFT TYPE (Model RX84 Only) ................................................................... 3-4

DUAL TAIL WHEEL INSTALLATION - LIFT TYPE (Model RX84 Only) ........................................................... 3-4

A-FRAME INSTALLATION (Quick Hitch) (Model RX60 & RX72) ..................................................................... 3-5

A-FRAME INSTALLATION (Model RX84) ........................................................................................................ 3-6

DRIVELINE ATTACHMENT ............................................................................................................................. 3-7

TONGUE (Pull Type) ........................................................................................................................................ 3-7

AXLE ASSEMBLY ............................................................................................................................................ 3-8

HYDRAULIC OR MANUAL LIFT (Model RX84 Only) ....................................................................................... 3-8

WHEELS (Model RX84 Only) ........................................................................................................................... 3-9

Front and Rear Deflectors (Standard Equipment) ......................................................................................... 3-10

Front Deflector .............................................................................................................................................. 3-10

Rear Deflector ................................................................................................................................................. 3-10

CHAIN GUARDS (Optional Equipment - All Models) ...................................................................................... 3-11

Front Chain Guards ........................................................................................................................................ 3-11

Rear Chain Guard ........................................................................................................................................... 3-11

HYDRAULIC OR MANUAL LIFT (Model RX84 Only) .....................................................................................3-12

CHECK CHAINS (Extra Equipment) ............................................................................................................... 3-12

OFFSET ADAPTER HITCH (EXTRA EQUIPMENT) ...................................................................................... 3-13

OPERATION SECTION ...................................................................................................... 4-1

OPERATOR REQUIREMENTS ........................................................................................................................ 4-3

TRACTOR REQUIREMENTS ........................................................................................................................... 4-4

ROPS and Seat Belt ......................................................................................................................................... 4-4

Tractor Safety Devices ...................................................................................................................................... 4-4

Tractor Horsepower .......................................................................................................................................... 4-5

3-Point Hitch ..................................................................................................................................................... 4-5

Front End Weight .............................................................................................................................................. 4-5

Drawbar-Pull Type Mower ................................................................................................................................ 4-6

Power Take Off (PTO) ...................................................................................................................................... 4-6

Tire Spacing ...................................................................................................................................................... 4-7

GETTING ON AND OFF THE TRACTOR ........................................................................................................ 4-7

Boarding the Tractor ......................................................................................................................................... 4-8

Dismounting the Tractor .................................................................................................................................... 4-8

STARTING THE TRACTOR ............................................................................................................................. 4-9

CONNECTING THE MOWER TO THE TRACTOR .......................................................................................... 4-9

Connecting the Mower-Lift Type ..................................................................................................................... 4-10

3-Point Quick Hitch ......................................................................................................................................... 4-10

Connecting Mower - Lift Type (Quick Hitch) ................................................................................................... 4-11

Safety Tow Chain ............................................................................................................................................ 4-11

SETTING THE MOWER ................................................................................................................................. 4-12

Setting Mower Height- Lift Type - (Standard or Quick Hitch) .......................................................................... 4-12

Connecting the Mower-Pull Type .................................................................................................................... 4-14

Setting Mowing Height-Pull Type .................................................................................................................... 4-15

Setting Deck Pitch ........................................................................................................................................... 4-16

DRIVELINE ATTACHMENT ........................................................................................................................... 4-16

Driveline Length Check ................................................................................................................................... 4-17

PRE-OPERATION INSPECTION AND SERVICE .......................................................................................... 4-18

Tractor Pre-Operation Inspection/Service ....................................................................................................... 4-19

Mower Pre-Operation Inspection/Service ....................................................................................................... 4-19

Cutting Component Inspection ........................................................................................................................ 4-23

Blade Bolt Inspection ...................................................................................................................................... 4-26

DRIVING THE TRACTOR AND IMPLEMENT ................................................................................................ 4-29

Starting the Tractor ......................................................................................................................................... 4-30

Brake and Differential Lock Setting ................................................................................................................. 4-30

Raising the Mower .......................................................................................................................................... 4-31

Driving the Tractor and Mower ........................................................................................................................ 4-31

Crossing Ditches and Steep Inclines .............................................................................................................. 4-32

OPERATING THE TRACTOR AND IMPLEMENT .......................................................................................... 4-33

Foreign Debris Hazards .................................................................................................................................. 4-34

Bystanders/Passersby Precautions ................................................................................................................ 4-34

Engaging the Power Take Off (PTO) .............................................................................................................. 4-35

PTO RPM and Ground Speed ........................................................................................................................ 4-36

Operating the Mower ...................................................................................................................................... 4-36

Cutting Material ............................................................................................................................................... 4-37

Right of Way (Highway) Mowing ..................................................................................................................... 4-40

Shutting Down the Implement ......................................................................................................................... 4-41

DISCONNECTING THE MOWER FROM THE TRACTOR ............................................................................ 4-41

MOWER STORAGE ....................................................................................................................................... 4-43

TRANSPORTING THE TRACTOR AND IMPLEMENT .................................................................................. 4-43

Transporting on Public

Roadways .................................................................................................................. 4-44

Hauling the Tractor and Implement ................................................................................................................. 4-46

TROUBLE SHOOTING GUIDE ...................................................................................................................... 4-47

MAINTENANCE SECTION ................................................................................................. 5-1

HAZARDS WITH MAINTENANCE OF IMPLEMENT ....................................................................................... 5-2

Lubrication ........................................................................................................................................................ 5-3

GEARBOX (Model RX60 & RX84) .................................................................................................................... 5-6

GEARBOX (Model RX72) ................................................................................................................................. 5-6

DRIVELINE LUBRICATION .............................................................................................................................. 5-7

LIFT TYPE DRIVELINE & PULL JACKSHAFT SHIELDS ................................................................................ 5-8

CV TYPE DRIVELINE ....................................................................................................................................... 5-9

MAIN CV DRIVELINE SAFETY SHIELD .......................................................................................................... 5-9

BLADE SERVICING ....................................................................................................................................... 5-11

BLADE SHARPENING ................................................................................................................................... 5-12

BLADE CARRIER REMOVAL ........................................................................................................................ 5-12

BLADE CARRIER INSPECTION .................................................................................................................... 5-12

BLADE CARRIER INSTALLATION ................................................................................................................ 5-13

BLADE REMOVAL .......................................................................................................................................... 5-14

SLIP CLUTCH ................................................................................................................................................. 5-14

SEASONAL CLUTCH MAINTENANCE .......................................................................................................... 5-15

STORAGE ...................................................................................................................................................... 5-16

PROPER TORQUE FOR FASTENERS ......................................................................................................... 5-16

GEARBOX SERVICING (Models RX60 & RX84) ........................................................................................... 5-18

GEARBOX DISASSEMBLY ............................................................................................................................ 5-19

RIGHT ANGLE GEARBOX (OUTBOARD) ASSEMBLY & DISASSEMBLY PROCEDURES ......................... 5-20

Input Shaft Removal ....................................................................................................................................... 5-20

Output Shaft Removal ..................................................................................................................................... 5-20

Parts Inspection .............................................................................................................................................. 5-21

Output Shaft Installation .................................................................................................................................. 5-21

Input Shaft Installation .................................................................................................................................... 5-22

GEARBOX SERVICING (Model RX72) .......................................................................................................... 5-23

Top Input Shaft Preload Setting ...................................................................................................................... 5-25

Right Angle Gearbox Assembly & Disassembly Procedures ..........................................................................5-25

Assembly Procedure ....................................................................................................................................... 5-26

Safety Section 1-1

SAFETY SECTION

SAFETY

RX60/72/84 10/12 Safety Section 1-2

SAFETY

GENERAL SAFETY INSTRUCTIONS AND PRACTICES

A careful operator is the best operator. Safety is of primary importance to the manufacturer and should be to

the owner/operator. Most accidents can be avoided by being aware of your equipment, your surroundings,

and observing certain precautions. The first section of this manual includes a list of Safety Messages that, if

followed, will help protect the operator and bystanders from injury or death. Read and understand these

Safety Messages before assembling, operating or servicing this Implement. This equipment should only be

operated by those persons who have read the manual, who are responsible and trained, and who know how

to do so responsibly.

The Safety Alert Symbol combined with a Signal Word, as seen below, is used throughout this

manual and on decals which are attached to the equipment. The Safety Alert Symbol means:

“ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!” The Symbol and Signal Word

are intended to warn the owner/operator of impending hazards and the degree of possible injury

faced when operating this equipment.

Indicates an imminently hazardous situation that, if not avoided, WILL result in DEATH OR

VERY SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, COULD result in DEATH

OR SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, MAY result in MINOR

INJURY.

Identifies special instructions or procedures that, if not strictly observed, could result in

damage to, or destruction of the machine, attachments or the environment.

NOTE: Identifies points of particular interest for more efficient and convenient operation or repair.

READ, UNDERSTAND, and FOLLOW the following Safety Messages. Serious injury or

death may occur unless care is taken to follow the warnings and instructions stated in this

Manual and in the Safety Messages on the implement. Always follow the instruction in this

manual and use good common sense to avoid hazards.

NOTE: If you want a translation of this safety section in one of the following Languages, please contact:

Translations at 1502 E. Walnut Street Seguin, TX 78155; Fax: (830) 372-9529; Safety Section Translations

are available in Spanish, Portuguese, French, German, Russian.

PN GS01

Practice all usual and customary safe working precautions and above all---

remember safety is up to YOU

. Only YOU can prevent serious injury or death

from unsafe practices.

SAFETY

RX60/72/84 10/12 Safety Section 1-3

SAFETY

OPERATOR SAFETY

TO AVOID SERIOUS INJURY OR DEATH DO THE FOLLOWING:

• READ, UNDERSTAND and FOLLOW Operator's Manual instructions, Warnings and Safety Messages.

• WEAR SAFETY GLASSES, safety shoes, hard hat, hearing protection and gloves when operating or

repairing equipment

• WEAR appropriate breathing respirator when operating in dusty conditions to avoid respiratory diseases.

• DO NOT WEAR loose clothing or jewelry to avoid rotating parts entanglement injury.

• DO NOT USE DRUGS or ALCOHOL before or while operating equipment.

• DO NOT ALLOW anyone to operate equipment under the influence of drug or alcohol.

• CONSULT medical professional for medication impairment side effects.

• STAY ALERT, prolonged operation can cause fatigue, STOP and REST.

GENERAL OPERATING SAFETY

VISIBILITY CONDITIONS WHEN MOWING:

• OPERATE IN DAYLIGHT or with lights that gives at least 100 yards clear visibility.

• BE ABLE TO SEE and identify passersby, steep slopes, ditches, drop-offs, overhead obstructions, power

lines, debris and foreign objects.

GROUND SPEED WHEN MOWING:

• NORMAL SPEED range is between 2 to 5mph.

• ADJUST MOWING SPEED for terrain conditions and grass type, density and cut height.

• REDUCE MOWING SPEED when near steep slopes, ditches, drop-offs, overhead obstructions, power

lines and to avoid debris and foreign objects.

INSECT INFESTATION

• Do Not operate in areas where bees or insects may attack unless you WEAR PROTECTIVE CLOTHING

or use enclosed tractor cab.

PTO SPEED:

• DO NOT EXCEED IMPLEMENT RATED PTO SPEED

• AVOID exceeding rated PTO speeds that may result in broken drivelines or blade failures.

SAFETY SIGNS:

• REPLACE missing, damaged or unreadable safety signs immediately.

PN OS01

SAFETY

RX60/72/84 10/12 Safety Section 1-4

SAFETY

CONNECTION OR DISCONNECTING IMPLEMENT SAFETY

TO AVOID SERIOUS INJURY OR DEATH FROM BEING CRUSHED BY TRACTOR OR

IMPLEMENT:

WHEN BACKING

tractor to implement hitch:

• DO NOT ALLOW BYSTANDERS between tractor and implement

BEFORE connecting and disconnecting implement hitch:

• STOP TRACTOR ENGINE, place transmission into park, engage parking brake and remove key.

WHEN

connecting and disconnecting implement hitch:

• DO NOT crawl or walk under raised mower or wing.

• USE tongue JACK to lift heavy implement tongues to control implement tongue movement.

• AVOID overloading jack to prevent jack failure and injury.

WHEN CONNECTING IMPLEMENT DRIVELINE:

TO AVOID

implement driveline coming loose during operation:

• LUBRICATE yoke spring locking collar to ensure it freely slides on PTO shaft

• SECURELY seat yoke locking balls in PTO shaft groove.

• PUSH and PULL DRIVELINE on both the tractor and implement PTO SHAFTS to ensure it is SECURELY

ATTACHED

TO AVOID

broken driveline during operations:

• CHECK driveline for proper length between PTO shaft and implement gearbox shaft.

• Drivelines too short can pull apart or disengage.

• Drivelines too long can bottom out.

• Bottoming driveline telescoping assembly will stop sliding and become solid.

• Driveline bottoming can push through support bearings and break off PTO shaft.

CONTACT DEALER

if implement driveline does not match Tractor PTO shaft:

• DO NOT USE PTO ADAPTER.

Using a PTO adapter can cause:

• Excessive vibration, thrown objects, blade and implement failures by doubling operating speed.

• Increased working length exposing unshielded driveline areas and entanglement hazards.

DO NOT connect the Mower to a tractor with the PTO directly connected to the Tractor transmission. PN CD02

SAFETY

RX60/72/84 10/12 Safety Section 1-5

SAFETY

CRUSHING HAZARDS

TO AVOID SERIOUS INJURY OR DEATH FROM FALLING OFF TRACTOR, EQUIPMENT RUN OVER,

ROLLOVER AND CRUSHING BY FALLING WING OR IMPLEMENT:

• USE ROPS and SEAT BELT equipped tractors for mowing operations.

• KEEP ROPS lock in up position.

• ALWAYS BUCKLE UP seat belt when operating tractor and equipment.

• ONLY OPERATE tractor and equipment while seated in tractor seat.

WHEN RAISING OR LOWERING IMPLEMENT:

•Raise or lower ONLY WHILE SEATED in tractor seat with seat belt buckled.

•Raise or lower ONLY when implement tongue is securely attached to tractor drawbar TO AVOID implement tip over.

• KEEP BYSTANDERS CLEAR of area TO AVOID crushing.

LIFTED Equipment can fall from mechanical or hydraulic failure or inadvertent Control Lever movement.

TO AVOID EQUIPMENT FALLING while working near or under lifted wings, components and

implements raised by 3-Pointed tractor hitch:

• SECURELY SUPPORT or block up raised equipment and components.

• BLOCK UP and securely support equipment before putting hands, feet or body under raised equipment or lifted compo-

nents.

WHEN PARKING Implement and Tractor:

• LOWER implement, LOCK or BLOCK lifted parts before leaving equipment.

• NEVER leave implement unattended in a raised position.

TO AVOID CHILDREN FALLING OFF OR BEING CRUSHED BY EQUIPMENT:

• NEVER ALLOW children to play on or around Tractor or Implement.

WHEN UNHITCHING IMPLEMENT:

• LOWER implement, LOCK or BLOCK lifted parts before leaving equipment.

• USE tongue jack to control implement tongue movement.

• USE tongue JACK to lift heavy implement tongues.

• AVOID overloading jack to prevent jack failure and injury.

PN CH02

SAFETY

RX60/72/84 10/12 Safety Section 1-6

SAFETY

THROWN OBJECTS HAZARDS

ROTARY MOWERS CAN THROW OBJECTS 300 FEET OR MORE UNDER ADVERSE

CONDITIONS.

TO AVOID SERIOUS INJURY OR DEATH TO OPERATOR OR BYSTANDERS FROM THROWN OBJECTS:

• KEEP bystanders 300 feet away

STOP MOWING IF PASSERSBY ARE WITHIN 300 FEET UNLESS:

• All THROWN OBJECT SHIELDING including, Front and Rear Deflectors, Chains Guards, Steel Guards, Bands,

Side Skirts and Skid Shoes in place and in good condition when mowing.

• Mower sections or wing are adjusted to be close and parallel to ground without exposing blades.

• MOWING AREA has been inspected and foreign materials and debris have been removed.

• PASSERSBY are inside enclosed vehicle.

INSPECT AREA FOR POTENTIAL THROWN OBJECTS BEFORE MOWING:

• REMOVE debris, rocks, wire, cable, metal objects and other foreign material from area.

Wire, cable, rope, chains and metal objects can be thrown or swing outside deck with great velocity:

1. MARK objects that cannot removed.

2. AVOID these objects when mowing.

HIGH GRASS and WEED AREA INSPECTION:

• INSPECT for and REMOVE any hidden large debris.

• MOW at Intermediate height

• INSPECT and remove remaining debris

• MOW at final height.

MOWER THROWN OBJECT SHIELDING:

• KEEP all thrown object shielding including, Front and Rear Deflectors, Chains Guards, Steel Guards, Bands, Side

Skirts and Skid Shoes in place and in good condition when mowing.

• DO NOT OPERATE with any thrown object shielding missing, damaged or removed.

RIGHT OF WAY (Highway) MOWING

• USE DOUBLE CHAIN GUARDS for highway, right-of-way, parks or greenbelt mowing or all other mowing where

human dwellings, vehicles, or livestock could be within 300 feet of the mower.

• No shielding is 100% effective in preventing thrown objects. To Reduce Possibility of Injury:

1. MAINTAIN MOWER SHIELDING, side skirts, skid shoes, and blades in good operational condition,

2. RAISE CUTTING HEIGHT to 6 INCHES minimum,

3. INSPECT AREA thoroughly before mowing to REMOVE potential THROWN OBJECT HAZARDS,

4. NEVER ALLOW BLADES to CONTACT SOLID OBJECTS like wire, rocks, post, curbs, guardrails, or ground

while mowing.

PN TO02

SAFETY

RX60/72/84 10/12 Safety Section 1-7

SAFETY

THROWN OBJECTS HAZARDS (CONTINUED)

MOWER OPERATION:

• DO NOT exceed mower's rated Cutting Capacity or cut non-vegetative material.

• USE ENCLOSED TRACTOR CABS when two or more mowers are operating in mowing area.

• ADJUST mower sections or wing close and parallel to ground without exposing blades

• ADJUST cutting HEIGHT to AVOID BLADE CONTACT with solid objects like wire, rocks, posts, curbs,

guard rails and fixed obstructions.

• DO NOT operate mower when mower is raised or in transport position

• STOP MOWING immediately if blades strike heavy objects, fixed structures, metal guard rails and con-

crete structures:

1. BLADES CAN FAIL from impact and objects can be thrown with great velocity.

2. INSPECT and REPLACE any damaged blades.

3. CHECK blade carrier balance and REPLACE if damaged.

• DO NOT mow in standing water TO AVOID possible BLADE FAILURE.

• AVOID MOWING in reverse:

1. STOP PTO and back up mower.

2. LOWER mower, engage PTO and mow forward.

• STOP PTO and BLADES when raising implement or the mower to transport position.

• DO NOT ENGAGE PTO with mower in transport position.

• STOP mowing when EXCESSIVE VIBRATION occurs:

1. STOP PTO and tractor ENGINE.

2. INSPECT mower for vibration source

3. REPLACE any damage parts and bent or damaged BLADES.

PN TO02-X

SAFETY

RX60/72/84 10/12 Safety Section 1-8

SAFETY

RUN OVER HAZARDS

TO AVOID SERIOUS INJURY OR DEATH FROM FALLING OFF TRACTOR OR

EQUIPMENT RUN OVER:

• USE ROPS and SEAT BELT equipped tractors for mowing operations.

• KEEP ROPS locked in UP position.

• ONLY start tractor while seated in tractor seat.

• ALWAYS BUCKLE UP seat belt when operating tractor and equipment.

• ONLY OPERATE tractor and equipment while seated in tractor seat.

• NEVER ALLOW RIDERS on tractor or implement.

WHEN MOUNTING AND DISMOUNTING TRACTOR:

• ONLY mount or dismount when tractor and moving parts are stopped.

• STOP ENGINE AND PTO, engage parking brake, lower implement, allow all moving parts to stop

and remove key before dismounting from tractor.

PN RO01

SAFETY

RX60/72/84 10/12 Safety Section 1-9

SAFETY

PTO ENTANGLEMENT HAZARDS

KEEP AWAY FROM ROTATING DRIVELINES AND ELEMENTS TO AVOID SERIOUS INJURY OR

DEATH:

STAY AWAY

and KEEP hands, feet and body AWAY from rotating blades, drivelines and parts until all moving

elements have stopped.

• STOP, LOOK and LISTEN before approaching the mower to make sure all rotating motion has stopped.

• ROTATING COMPONENTS CONTINUE to ROTATE after the PTO is shut off.

PTO SHIELDING:

TO AVOID SERIOUS INJURY OR DEATH FROM ENTANGLEMENT WHEN OPERATING IMPLEMENT:

• KEEP PTO shields, integral driveline shields and input shields installed

• DO NOT OPERATE mower without shields and guards in place or missing

• REPAIR OR REPLACE if damage, broken or missing

• ALWAYS REPLACE GUARDS that have been removed for service or maintenance.

• Do Not use PTO or PTO guard as a step.

TO AVOID

broken driveline during operations:

• CHECK driveline for proper length between PTO shaft and implement gearbox shaft.(Refer to Instructions in

Operation Section)

• Drivelines too short can pull apart or disengage.

• Drivelines too long can bottom out.

Bottoming driveline telescoping assembly will stop sliding and become solid.

• Driveline bottoming can push through support bearings and break off PTO shaft

• AVOID sharp turns or lift mower to heights to cause driveline "knocking".

• Lubricate driveshaft-telescoping components weekly.

CONTACT DEALER

if implement driveline does not match Tractor PTO shaft:

• DO NOT USE PTO ADAPTER.

Using a PTO adapter can cause excessive vibration, thrown objects, blade and implement failures by

doubling operating speed. Increased working length exposing unshielded driveline areas.

PN PE01

SAFETY

RX60/72/84 10/12 Safety Section 1-10

SAFETY

MOWER BLADE CONTACT HAZARDS

KEEP AWAY FROM ROTATING BLADES TO AVOID SERIOUS INJURY OR DEATH FROM

BLADE CONTACT:

• STAY AWAY and KEEP HANDS, FEET and BODY AWAY from rotating blades, drivelines and parts until all moving

elements have stopped.

• DO NOT put hands or feet under mower decks

• STOP rotating BLADES disengage PTO and wait for blade to stop rotating before raising mower deck or wings

• STOP LOOK and LISTEN before approaching the mower to make sure all rotating motion has stopped.

PN MB01

SAFETY

RX60/72/84 10/12 Safety Section 1-11

SAFETY

HIGH PRESSURE OIL LEAK HAZARDS

TO AVOID SERIOUS INJURY OR DEATH FROM HIGH PRESSURE HYDRAULIC OIL LEAKS

PENERATING SKIN:

• DO NOT OPERATE equipment with oil or fuel leaks.

• KEEP all hydraulic hoses, lines and connections in GOOD CONDITION and TIGHT before applying system

pressure.

• RELIEVE HYDRAULIC PRESSURE before disconnecting lines or working on the system.

• REMOVE and replace hose if you suspect it leaks. Have dealer test it for leaks.

HIGH PRESSURE FLUID LEAKS CAN BE INVISIBLE.

WHEN CHECKING FOR HYDRAULIC LEAKS AND WORKING AROUND HYDRAULIC SYSTEMS:

• ALWAYS WEAR safety glasses and impenetrable gloves.

• USE paper or cardboard to search for leaks.

• DO NOT USE hands or body parts to search for leak.

• KEEP hands and body AWAY from pin holes and nozzles ejecting hydraulic fluid.

• Hydraulic fluid may cause gangrene if not surgically removed immediately by a doctor familiar with this form of injury.

PN HP01

SAFETY

RX60/72/84 10/12 Safety Section 1-12

SAFETY

ELECTRICAL & FIRE HAZARDS

TO AVOID SERIOUS INJURY OR DEATH FROM ELECTRICAL CONTACT WHEN

WORKING AROUND ELECTRICAL POWER LINES, GAS LINES AND UTILITY LINES:

• INSPECT mowing area for overhead or underground electrical power lines, obstructions, gas lines,

cables and Utility, Municipal, or other type structure.

• DO NOT allow mower to contact with any Utility, Municipal, or type of structures and obstructions.

• CALL 811 and 1-800-258-0808 for identify buried utility lines.

FIRE PREVENTION GUIDELINES while Operating, Servicing, and Repairing Mower and Tractor to

reduce equipment and grass fire Risk:

• EQUIP Tractor with a FIRE EXTINGUISHER

• DO NOT OPERATE mower on a tractor equipped with under frame exhaust

• DO NOT SMOKE or have open flame near Mower or Tractor

• DO NOT DRIVE into burning debris or freshly burnt area

• AVOID FIRE IGNITION by not allowing mower blade to contact solid objects like metal or rock.

• ADJUST SLIP CLUTCHES to avoid excessive slippage and clutch plate heating.

• CLEAR any grass clippings or debris buildup around mower drivelines, slip clutches, and gearboxes.

• SHUT OFF ENGINE while refueling.

PN EF02

SAFETY

RX60/72/84 10/12 Safety Section 1-13

SAFETY

TRANSPORTING HAZARDS

TO AVOID SERIOUS INJURY AND DEATH WHEN TOWING OR TRANSPORTING EQUIPMENT:

• KEEP transport speed BELOW 20 mph to maintain control of equipment.

• REDUCE SPEED on inclines, on turns and in poor towing conditions.

• DO NOT TOW with trucks or other vehicles

• USE only properly sized and equipped tractor for towing equipment.

• FOLLOW all local traffic regulations.

TRACTOR REQUIREMENTS FOR TOWING OR TRANSPORTING IMPLEMENTS:

• ONLY TRANSPORT with tractor with ROPS in the raised position.

• USE properly sized and equipped tractor that exceeds implement weight by at least 20%

• KEEP 20% of tractor weight on front wheels to maintain safe steering.

BEFORE TRANSPORTING OR TOWING IMPLEMENT:

TRACTOR INSPECTION:

• CHECK steering and braking for proper operation and in good condition.

• CHECK SMV sign, reflectors and warning lights for proper operation and visibility behind unit.

• CHECK that your driving vision is not impaired by tractor, cab, or implement while seated in tractor seat.

• ADJUST your operating position, mirrors, and implement transport for clear vision for traveling and traffic conditions.

PREPARE IMPLEMENT FOR TRANSPORTING OR TOWING:

• DISENGAGE PTO

• RAISE MOWER

• REMOVE any cut material collected on mower deck.

TOWED MOWERS - ENGAGE TRANSPORT LOCKS AND SAFETY CHAINS:

• INSTALL center axle cylinder transport stops or pins

• ATTACH implement SAFETY CHAIN to tractor

DETERMINE STOPPING CHARACTERISTICS OF TRACTOR AND IMPLEMENT FOR TRANSPORTING OR

TOWING:

BRAKING TESTS:

• APPLY brakes at increasing speeds

• Observe STOPPING distances increases with increased speeds.

• DETERMINE the maximum safe transport speed that does not exceed 20 mph

DETERMINE MAXIMUM TURNING SPEED BEFORE OPERATING ON ROADS OR UNEVEN GROUND:

• TEST equipment in slowly increasing speed in turns to determine it can be operated at higher speeds.

• USE REDUCED turning speeds in sharp turns to avoid equipment turning over.

WHEN TOWING OR TRANSPORTING EQUIPMENT:

• Always WEAR SEAT BELT when operating or transporting mower.

• USE low speeds to avoid overturn with raised wings.

• USE low speeds and gradual steering on curves, hills, rough or uneven surfaces and on wet roads

• TURN ON tractor FLASHING WARNING LIGHTS.

• ALLOW cle

arance for implement swing while turning.

PN TH02

SAFETY

RX60/72/84 10/12 Safety Section 1-14

SAFETY

HAZARDS WITH MAINTENANCE OF IMPLEMENT

AVOID SERIOUS INJURY OR DEATH FROM COMPONENT FAILURE BY KEEPING IMPLEMENT IN

GOOD OPERATING CONDITION IN PERFORMING PROPER SERVICE, REPAIRS AND

MAINTENANCE.

BEFORE PERFORMING SERVICE, REPAIRS AND MAINTENANCE ON THE IMPLEMENT:

SECURE EQUIPMENT FOR SERVICE

BLOCK OUT POTENTIAL ENERGY HAZARDS; Rotating Parts, Raised Components, Hydraulic Pressure.

• STOP ENGINE AND PTO, engage parking brake, lower implement, allow all moving parts to stop and remove key before

dismounting from tractor.

•

PLACE implement on ground or securely block up raised equipment. Use large blocks on soft or wet soil.

• SECURELY LATCH and LOCK raised implement wings

• BLOCK UP IMPLEMENT TONGUE with large blocks and tongue jack. DO NOT crawl or work under implement supported only by

tongue jack.

•

PUSH and PULL Remote Hydraulic Cylinder lever to relieve hydraulic pressure.

• DISCONNECT IMPLEMENT Hydraulic HOSES from tractor

•

DISCONNECT IMPLEMENT driveline from tractor PTO SHAFT.

WEAR SAFETY GLASSES, PROTECTIVE GLOVES and follow SAFETY PROCEDURES when performing service, repairs

and maintenance on the implement:

•Always WEAR protective GLOVES when handling blades, knives, cutting edges or worn component with sharp edges.

•Always

WEAR GLOVES and SAFETY GLASSES when servicing hot components

•

AVOID CONTACT with hot hydraulic oil tanks, pumps, motors, valves and hose connection surfaces.

•

SECURELY support or BLOCK UP raised implement, framework and lifted components before working underneath equipment.

•

STOP any implement movements and SHUT-OFF TRACTOR engine before doing any work procedures.

•

USE ladder or raised stands to reach high equipment areas inaccessible from ground.

•

ENSURE good footing by standing on solid flat surfaces when getting on implement to perform work.

•

FOLLOW manufacturer's instructions in handling oils, solvents, cleansers, and other chemical agents.

•

DO NOT change any factory-set hydraulic calibrations to avoid component or equipment failures.

•

DO NOT modify or alter implement, functions or components.

•

DO NOT WELD or repair rotating mower components. These may cause vibrations and component failures being thrown from

mower.

PERFORM SERVICE, REPAIRS, LUBRICATION AND MAINTENANCE OUTLINED IN IMPLEMENT MAINTENANCE

SECTION:

• INSPECT for loose fasteners, worn or broken parts, leaky or loose fittings, missing or broken cotter keys and washers on pins, and

all moving parts for wear.

•

REPLACE any worn or broken parts with authorized service parts.

•

LUBRICATE unit as specified by lubrication schedule

•

NEVER lubricate, adjust or remove material while it is running or in motion.

•

TORQUE all bolts and nuts as specified.

BLADE INSPECTION:

• REPLACE bent, damage, cracked or broken blades immediately with new blades.

•

AVOID blade failures and thrown broken blades. DO NOT straighten, weld, or weld hard-facing blades.

SAFETY SHIELDS, GUARDS AND SAFETY DEVICES INSPECTION:

• KEEP all Deflectors, Chain Guards, Steel Guards, Gearbox Shields, and PTO integral shields, Bands, Side Skirts and Skid Shoes

in place and in good condition.

•

REPLACE any missing, broken or worn safety shields, guards and safety devices.

• Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the state of California

to cause cancer, birth defects or other reproductive harm.

• Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the state of California to

cause cancer, birth defects or other reproductive harm.

PN HM01

SAFETY

RX60/72/84 10/12 Safety Section 1-15

SAFETY

PARTS INFORMATION

Alamo Industrial mowers use balanced and matched system components for blade carriers, blades,

cuttershafts, knives, knife hangers, rollers, drivetrain components, and bearings. These parts are made and

tested to Alamo Industrial specifications. Non-genuine "will fit" parts do not consistently meet these

specifications. The use of “will fit” parts may reduce mower performance, void mower warranties, and present

a safety hazard. Use genuine Alamo Industrial mower parts for economy and safety.

(SPAM-1)

SEE YOUR ALAMO DEALER

SAFETY

RX60/72/84 10/12 Safety Section 1-16

SAFETY

Decal Location

NOTE: Alamo Industrial supplies safety decals on this product to promote safe operation. Damage to the

decals may occur while in shipping, use, or reconditioning. Alamo Industrial cares about the safety of its

customers, operators, and bystanders, and will replace the safety decals on this product in the field, free of

charge (Some shipping and handling charges may apply). Contact your Alamo Industrial dealer to order

replacement decals.

SAFETY

RX60/72/84 10/12 Safety Section 1-17

SAFETY

ITEM PART NO. QTY TYPE DESCRIPTION

1. D821 1 DANGER Multi Hazard

2. D388 1 WARNING Driveline Hazards

3. D534 1 WARNING Replace Blades in Pair/Torque 600ft/lbs

4. D816 1 WARNING Use Genuine Alamo Industrial Parts

5. 00785564 2 LOGO Alamo Industrial

6. 00771283 1 WARRANTY 5-Year

7. 03200347 * REFLECT SMV sign

8. 00785560 2 NAME RX60

00785561 2 NAME RX72

2 NAME RX84

9. 2738332 2 REFLECT Red Reflectors

10. nfs 1 SERIAL PLATE Serial Number Plate

11. 00756004 1 DANGER Shield Missing

12. 00756005 1** DANGER Rotating Driveline (Not Shown)

13. D454 1 WARNING Crushing Hazard

14. D518 1 WARNING Jack Positioning

15. D614 2 DANGER Thrown object shield missing

16. D137 1 INSTRUCT CCW Blade Rotation

17. D590 1 INSTRUCT Lube Chart

18. D817 1 DANGER Multi-Language General Safety

19. 00785565 2 LOGO Alamo Industrial

20. D390 1 WARNING Pull Type Unit Hazards

21. 00776031 1 Canister, Operators Manual

* Furnished by Tractor Manufacturer

** Furnished by Driveline Manufacturer

Decal Sheets

Name 00781352 (SAFETY)

Name 00785504 (RX60 LOGOS)

Name 00785507 (RX72 LOGOS)

Name 00785510 (RX84 LOGOS)

SAFETY

RX60/72/84 10/12 Safety Section 1-18

SAFETY

Decal Description

SAFETY

RX60/72/84 10/12 Safety Section 1-19

SAFETY

RX60/72/84 10/12 Safety Section 1-20

SAFETY

RX60/72/84 10/12 Safety Section 1-21

SAFETY

RX60/72/84 10/12 Safety Section 1-22

SAFETY

RX60/72/84 10/12 Safety Section 1-23

SAFETY

RX60/72/84 10/12 Safety Section 1-24

SAFETY

RX60/72/84 10/12 Safety Section 1-25

SAFETY

RX60/72/84 10/12 Safety Section 1-26

SAFETY

RX60/72/84 10/12 Safety Section 1-27

SAFETY

Federal Laws and Regulations

This section is intended to explain in broad terms the concept and effect of federal laws and regulations concerning

employer and employee equipment operators. This section is not intended as a legal interpretation of the law and

should not be considered as such.

Employer-Employee Operator Regulations

U.S. Public Law 91-596 (The Williams-Steiger Occupational and Health Act of 1970) OSHA

This Act Seeks:

“...to assure so far as possible every working man and woman in the nation safe and healthful working

conditions and to preserve our human resources...”

DUTIES

Sec. 5 (a) Each employer-

(1) shall furnish to each of his employees employment and a place of employment which are free from

recognized hazards that are causing or are likely to cause death or serious physical harm to his employees;

(2) shall comply with occupational safety and health standards promulgated under this Act.

(b) Each employee shall comply with occupational safety and health standards and all rules, regulations and

orders issued pursuant to this Act which are applicable to his own actions and conduct.

OSHA Training Requirements

Title 29, Code of Federal Regulations Part 1928.57(a)(6). www.osha.gov

Operator instructions. At the time of initial assignment and at least annually thereafter, the employer shall

instruct every employee who operates an agricultural tractor and implements in the safe operating practices

and servicing of equipment with which they are or will be involved, and of any other practices dictated by the

work environment.

Keep all guards in place when the machine is in operation;

Permit no riders on equipment

Stop engine, disconnect the power source, and wait for all machine movement to stop before servicing,

adjusting, cleaning or unclogging the equipment, except where the machine must be running to be properly

serviced or maintained, in which case the employer shall instruct employees as to all steps and procedures

which are necessary to safely service or maintain the equipment.

Make sure everyone is clear of machinery before starting the engine, engaging power, or operating the

machine.

Employer Responsibilities:

To ensure employee safety during Tractor and Implement operation, it is the employer’s responsibility to:

1. Train the employee in the proper and safe operation of the Tractor and Implement.

2. Require that the employee read and fully understand the Tractor and Implement Operator’s manual.

3. Permit only qualified and properly trained employees to operate the Tractor and Implement.

4. Maintain the Tractor and Implement in a safe operational condition and maintain all shields and guards on the

equipment.

5. Ensure the Tractor is equipped with a functional ROPS and seat belt and require that the employee operator

securely fasten the safety belt and operate with the ROPS in the raised position at all times.

6. Forbid the employee operator to carry additional riders on the Tractor or Implement.

7. Provide the required tools to maintain the Tractor and Implement in a good safe working condition and provide the

necessary support devices to secure the equipment safely while performing repairs and service.

8. Require that the employee operator stop operation if bystanders or passersby come within 300 feet.

Child Labor Under 16 Years of Age

Some regulations specify that no one under the age of 16 may operate power machinery. It is your responsibility to

know what these regulations are in your own area or situation. (Refer to U.S. Dept. of Labor, Employment Standard

Administration, Wage & Home Division, Child Labor Bulletin #102.)

Introduction Section 2-1

INTRODUCTION SECTION

INTRODUCTION

RX60/72/84 10/12 Introduction Section 2-2

INTRODUCTION

We are pleased to have you as an Alamo Industrial customer. Your Rotary Cutter has been carefully designed

with care and built with quality materials by skilled workers to give maximum service with minimum down time.

This manual is provided to give you the necessary operating and maintenance instructions for keeping your

rotary cutter in top operating condition. Careful use and timely service saves extensive repairs and costly

downtime losses. Please read this manual thoroughly. Understand what each control is for and how to use it.

Alamo Industrial typically offers three types of shielding to protect the operator, passerby, livestock, and

property from thrown objects... deflectors, single chain guards, and double chainguards. Shielding should be

selected based on the intended use of the mower. Double chainguards or deflectors should be used for

highway, right-of-way, parks or greenbelt mowing or all other mowing where human dwellings, vehicles, or

livestock could be within 300 feet of the mower. Chainguards are more durable, provide a longer service life

and require less maintenance and replacement than deflectors. Single chainguards may be sufficient for

agriculture and other mower use only where passersby or property are not within 300 feet of the mower during

operation.

No shielding is 100% effective in preventing thrown objects. The possibility of injury and property damage from

this hazard can be substantially reduce by selecting proper shielding, maintaining the mower and shielding in

good operational condition, inspecting the area for foreign debris before mowing, operating the mower at a

minimum cutting height of 4", and keep unprotected persons at a minimum distance of 300 feet from the

mower at all times during operation.

Safety is of primary importance to the owner/operator and to the manufacturer. Observe all safety precautions

decaled on the machine and noted throughout the manual for safe operation of implement. If any assistance or

additional information is needed, contact your authorized Alamo Industrial dealer. The owner/operator/dealer

should know and understand the Safety Messages before assembly and be aware of the hazards of operating

this cutter during assembly, use, and maintenance. The Safety Alert Symbol combined with a Signal Word, as

seen below, is intended to warn the owner/operator of impending hazards and the degree of possible injury

faced when operating this machine.

Indicates an imminently hazardous situation that, if not avoided, WILL result in DEATH OR

VERY SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, COULD result in DEATH

OR SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, MAY result in MINOR

INJURY.

Identifies special instructions or procedures that, if not strictly observed, could result in

damage to, or destruction of the machine, attachments or the environment.

INTRODUCTION

RX60/72/84 10/12 Introduction Section 2-3

INTRODUCTION

The Alamo Industrial RX60/72/84 Rotary Mower is designed for medium duty

applications such as weed, grass, corn stalks, and light brush to 2-1/2” diameter.

These mowers are single spindle with two free-swinging blades. Free swinging blades

reduce the shock of impact when a stationary object is hit. Additional protection is

provided by a slip clutch on the gearbox input shaft. A round blade holder allows the

mower to “ride over” stumps and similar immovable objects. These Mowers are

attached to the tractor using 3-point Cat I, Cat II or III standard or quick hitches or pull

hitches. Standard equipment includes driveline shields, clutch shields and front and

rear discharge shields.

Equipment Specifications

60 72 84 60 72 84

Cutting Width 60” 72” 84” PTO 540 PTO

540 PTO 540 PTO

Transport Width 67-1/2” 79-1/2” 89-1/2” Blade Tip Speed

Overall Width --------” ---------” ---------” Center 13,572 16,286 16,328

Overall Length 111” 123” 138-1/2” Center 1000 (PTO) --------- --------- 15,994

Cutting Height 1-1/2” Min. 1-1/2” Min. 1/1/2” Min. Gearbox

HP Required (min.) 35 Min.HP 45 Min. HP 65(lift) 30(pull) Gearbox Rating 130 HP 130HP 130HP

Cutting Capacity (max) 2-1/2” 2-1/2” 2-1/2” LImited Warranty 5 Year 5 Year 5 Year

Weight 998 lbs 1158 lbs 1540 lbs Driveline

Driveline Size CAT4 CAT4 CAT4

Limited Warranty 1 Year 1 Year 1 Year

INTRODUCTION

RX60/72/84 10/12 Introduction Section 2-4

INTRODUCTION

KEY OPERATION POINTS

• Cutting performance and distribution are best when cutter is level from side to side and front to rear.

• In extra heavy material, rear chains will allow better discharge and better distribution than solid rear bands.

• Never operate the Mower below full PTO speed of 540 or 1000 rpm.

• Corn should be cut at 5 to 6 mph. If full PTO rpm cannot be maintained, use one lower gear.

Operating Noise Level/Sound Pressure

The sound levels at the operator's ear from the attached machine (rotary cutter) are at least 10 dB(A) below the

levels from typical Agricultural tractors used to power and transport this machine. Therefore, the Noise

emission values given by the OEM of the Agricultural tractor used to power and transport this machine would

be valid when this machine is attached to and operated by that Agricultural tractor in all OEM recommended

applications.

Warranty information

In addition to the standard Limited Warranty shown on the facing page, Alamo Industrial also provides:

1. A FIVE-YEAR (60 months) LIMITED WARRANTY* on GEARBOX components provided they have been

properly maintained and have not been subjected to abuse or mis-use except as limited below.

* WARRANTY LIMITATIONS - GEARBOX

A. Warranty is ONE-YEAR (12 MONTHS) for Seals (After one year, seals are considered to be WEARING

PARTS and replacement is the users' responsibility.)

B. Users' Gearboxes may be rebuilt by Alamo Industrial or replaced by new or rebuilt Gearboxes at the option

of Alamo Industrial.

2. ONE-YEAR (12 months) LIMITED WARRANTY** on the DRIVELINE components provided they have been

properly maintained and have not been subjected to abuse or misuse.

* *WARRANTY LIMITATIONS - DRIVELINE

A. Warranty is ONE-YEAR (12 MONTHS) for DRIVELINE SHIELDS except that evidence of wear from contact

with other parts on the shield voids this warranty.

B. Shield Bearings are wearing parts and are not warrantable.

C. Slip-Clutch Disks are wearing parts and are not warrantable. Evidence of “burning up” Slip Clutch Plates

due to improper adjustment will void warranty on Slip Clutch Parts.

INTRODUCTION

RX60/72/84 10/12 Introduction Section 2-5

INTRODUCTION

ALAMO-INDUSTRIAL

LIMITED WARRANTY

1. LIMITED WARRANTIES

1.01. Alamo Industrial warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser

(“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”) that the goods purchased

are free from defects in material or workmanship.

1.02. Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be defective under

normal use and service due to defects in material or workmanship.

1.03. This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence,

alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, or which has served

its normal life. This limited warranty does not apply to any part of any internal combustion engine, or expendable items such as

blades, shields, guards, or pneumatic tires except as specifically found in your Operator’s Manual.

1.04. Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any nature on behalf of

Manufacturer.

2. REMEDIES AND PROCEDURES.

2.01. This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer within 30 days

of purchase.

2.02. Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased the goods or an

approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which the claim is based.

2.03. Purchaser is responsible for returning the goods in question to the Dealer.

2.04. If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and service due to

defects in material or workmanship, Manufacturer will:

(a)Repair or replace the defective goods or part(s) or

(b)Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer) if

Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty by

Manufacturer.

The choice of remedy shall belong to Manufacturer.

2.05. Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and for returning the

goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s)

from the Dealer to the designated factory.

3. LIMITATION OF LIABILITY.

3.01. MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES WITH

RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE.

3.02. MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR USE OF THE

GOODS.

3.03. EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO PURCHASER OR

ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE CAUSED OR ALLEGED TO BE

CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOT LIMITED TO, ANY INDIRECT, SPECIAL,

CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROM THE USE OR OPERATION OF THE GOODS OR ANY

BREACH OF THIS WARRANTY. NOT WITHSTANDING THE ABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER’S

LIABILITY HEREUNDER FOR DAMAGES INCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE

GOODS.

3.04. NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER THIS WARRANTY

MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS OCCURRED.

4. MISCELLANEOUS.

4.01. Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County, Texas.

4.02. Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a

waiver of any other term.

4.03. If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such

provision shall not invalidate any other provisions herein.

4.04. Applicable law may provide rights and benefits to purchaser in addition to those provided herein.

KEEP FOR YOUR RECORDS

ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine identification

when applying for warranty.

Alamo Industrial Implement Model________________________________SerialNumber__________________

Date Purchased______________________________________ Dealer_______________________________

ATTENTION:

READ YOUR OPERATOR'S MANUAL

ALAMO INDUSTRIAL

An Alamo Group Company

Post Office Drawer 549

Seguin, Texas 78156

830-379-1480

Assembly Section 3-1

ASSEMBLY SECTION

ASSEMBLY

RX60/72/84 10/12 Assembly Section 3-2

ASSEMBLY

DEALER SETUP INSTRUCTIONS

The mower as received from the factory is partially assembled and requires minimum time to complete

assembly and is ready for sale.

This mower is shipped vertically with shipping brackets. These shipping brackets are intended for use in

transporting the mower from the factory to dealer.

DO NOT use these brackets to store the unit. DO NOT store mower vertically, the mower

can fall over resulting in serious injury or death. To avoid injury always store mower lying

down on flat ground.

Assembly will be easier if components are aligned and loosely assembled before tightening hardware. Refer to

bolt torque chart in Maintenance Section. All bolts are grade 5 unless otherwise specified.

PULL TYPE (RX84 ONLY) INSTRUCTIONS

The standard Pull-Type Unit will be shipped from the factory in the following bundles: 1) Basic Assembly, 2)

Jack shaft Assembly, 3) Jackshaft Bearing Support, 4) Gearbox Protective Shield, 5) PTO Driveline, 6) Tongue

Assembly, 7) Control Rod Bundle, 8) Axle Arm Bundle and Lift Lug and or Spring Assembly, 9) Wheels, 10)

Jack, 11) Operator’s Manual and Flat Blades. Other optional bundles that may be shipped with your unit:

Ratchet Lift Screw or Hydraulic Cylinder with Hydraulic Hose and Hose Bracket, Puncture-Proof tires or 14” or

15” Wheels, Chain Guards. Extra Equipment items include: Chain Guards, Solid Guards, Dual Wheels, Hitch

and Spring Assembly (Axle).

The Components of these machines are quite heavy. Block all components up securely

before working under or putting extremities under such parts.

ASSEMBLY

RX60/72/84 10/12 Assembly Section 3-3

ASSEMBLY

SHIELD ASSEMBLY (All Models)

SLIP CLUTCH SHIELD

1. To attach the Slip Clutch Shield

Guide shield bracket (2) through weldment shield

(1) so that bracket stud screw protrudes through

weldment hole and retain in place with wingnut (3).

2. Align holes of shield bracket with gearbox holes

positioned around input shaft. Retain bracket to

gearbox with three 3/8” x 3/4” bolts (6), 3/8”

washers (4), and 3/8” lockwashers (5). Posi-

tion hardware as follows: gearbox, bracket, flat-

washer, lockwasher, bolt. Tighten bolts to

recommended torque. Figure Asm-R-0091.

TAIL WHEEL INSTALLATION

(Model RX60 & RX72)

Align Tail Wheel Beam Weldment (1) between pivot

brackets located behind gearbox mount on the

Mainframe Weldment. NOTE: Long side of caster

fork pivot tube is positioned up. Attach the Tail

Wheel Beam Weldment (1) to the Mainframe

Weldment with one 5/8” Bolt (4), and 5/8” nut (5).

Slide Tail Wheel Beam Weldment (1) into Gauge

Wheel Mount Weldment (3) and retain with two 1/2”

x 1-1/2” bolts (6), and locknuts (7).

1. Insert the Caster Fork Weldment (11) into the

Tail Wheel Beam (1) and retain with Flatwasher

(9) and Cotter Pin (10).

2. Tighten all bolts to the proper torque. Figure

Asm-R-0408.

ASSEMBLY

RX60/72/84 10/12 Assembly Section 3-4

ASSEMBLY

TAIL WHEEL INSTALLATION - LIFT TYPE (Model RX84 Only)

1. Slide bracket (2) onto beam (1).

2. Insert bolt (28) through lugs on end of beam (1)

and lug on deck.

NOTE: Insert spacer (10)into deck lug before

inserting bolt (28). Install locknut (3).

3. Install bracket (4) to rear center of deck using

bolt (24) and retain using locknut (23).

4. Insert bolt (24) through holes in brackets (2)

and (4) which will give approximately desired

cutting height. Install locknut (23) and tighten all

bolts. Figure Asm-R-0402.

DUAL TAIL WHEEL INSTALLATION - LIFT TYPE (Model RX84 Only)

1. Attach the tailwheel beam (1) to the lug toward

the outer edge of the deck just to the rear of the

cross reinforcement using bolt (2) and nut (3).

Note: Slide position bracket (4) onto beam

before installing.

2. Attach the brackets (5) to the deck using bolts

(29) and nuts (30). Insert bolt (29) through

holes in brackets (5) and (4) which will give

approximate desired cutting height. Install lock-

nut (30) and tighten all bolts.

ASSEMBLY

RX60/72/84 10/12 Assembly Section 3-5

ASSEMBLY

A-FRAME INSTALLATION (Quick Hitch) (Model RX60 & RX72)

1. Attach the A-Frame Bars (2) to the right and left Hitch Lugs (14 & 15) with two 5/8” x 2” bolts (16), 5/8”

washers (17), bushing (18) and 5/8” locknuts (19) Figure Asm-R-0342.

2. Attach the Lift Strap Bars (1) to the Mainframe with two 5/8” bolts (16), 5/8” flatwasher (17), bushing (18)

and 5/8” locknut (19) Figure Asm-R-0341.

3. Attach flex links (3) to A-Frame bars (2) with 5/8” x 3” carriage bolts (7), bushings (8), flatwasher (9) and

nut (10).

4. Insert quick hitch bushing (5) between A-Frame and insert 5/8” x 4-1/2” bolt (4) and 3/4” locknut (6).

5. Insert 5/8” x 2-3/4 bolt (11) through center holes in flex links (3) with bushing (12) through forward holes in

rear braces (1).

6. Insert bolt (13) through 2nd hole from front in rear braces (1) and secure with locknut (10).

7. Insert 5/8” x 2-3/4” bolt (11) through rear holes in flex links (3) through bushing (12) with bushing over or on

top of rear braces (1).

ASSEMBLY

RX60/72/84 10/12 Assembly Section 3-6

ASSEMBLY

A-FRAME INSTALLATION (Model RX84)

1. Attach the A-Frame Bars (2) to the right and left Hitch Lugs (14 & 15) with two 5/8” x 2” bolts (16), 5/8”

washers (17), bushing (18) and 5/8” locknuts (19).

2. Attach the Lift Strap Bars (1) to the Mainframe with two 5/8” bolts (16), 5/8” flatwasher (17), bushing (18)

and 5/8” locknut.

3. Attach flex links (3) to A-Frame bars (2) with 5/8” x 3” carriage bolts (7), bushings (8), flatwasher (9) and

nut (10).

4. Insert quick hitch bushing (5) between A-Frame and insert 5/8” x 4-1/2” bolt (4) and 3/4” locknut (6).

5. Insert 5/8” x 2-3/4 bolt (11) through center holes in flex links (3) with bushing (12) through forward holes in

rear braces (1).

6. Insert bolt (13) through 2nd hole from front in rear braces (1) and secure with locknut (10).

7. Insert 5/8” x 2-3/4” bolt (11) through rear holes in flex links (3) through bushing (12) with bushing over or on

top of rear braces (1). Figure Asm-R-0404

ASSEMBLY

RX60/72/84 10/12 Assembly Section 3-7

ASSEMBLY

DRIVELINE ATTACHMENT

Before starting assembly, make certain that all paint, dirt, and grease are removed from gearbox shaft (1). To

ease assembly apply a light coat of grease to splines and assemble. Do not assemble a driveline without a

shield. Entanglement in rotating shafts can kill. Figure Asm-R-0090

Attach slip clutch end of the driveline to the gearbox

input shaft securely. Make certain that the slip

clutch is fully onto the input shaft splines. Tighten

the locknuts (2) alternately until they have reached

the proper torque. Refer to Torque Chart in the

Maintenance Section.

TONGUE (Pull Type)

Insert tongue lugs (4) between mainframe uprights and retain using special pin (16). Insert retaining clip (17) to

retain pin. Be sure to install bushing (19) on each side to eliminate side movement. Figure Asm-R-0405

ASSEMBLY

RX60/72/84 10/12 Assembly Section 3-8

ASSEMBLY

AXLE ASSEMBLY

Attach rear axle (1) to the lugs on the rear of the mainframe using 3/4 x 3 (8) bolts, bushings (7), flatwashers

(4) and locknuts (6). Tighten all bolts. Attach level lift rod assemblies to axle (1) Figure Asm-R-0406 and

tongue (1) Figure Asm-R-0405 using clevis pin (15), flatwashers (31) and cotter pin (38). NOTE: The

adjusting nuts on control rods should be to rear of machine. Figure Asm-R-0406

HYDRAULIC OR MANUAL LIFT (Model RX84 Only)

Install the Hydraulic Cylinder or the manual Ratchet Lift Screw (Asm-0039) between the Axle Center Lug and

the Lug directly behind the Center Gearbox. Install cylinder pins provided and retain with cotter pins.

NOTE: Figure Asm-0038 shows optional spring shock installation.

ASSEMBLY

RX60/72/84 10/12 Assembly Section 3-9

ASSEMBLY

WHEELS (Model RX84 Only)

Install the Wheels on the Wheel Hubs. Note: If Laminated Tires are used, place the flat side of the Lug Nut

against the Wheel Asm-R-0127. Note direction of travel and curvature of rubber segments in tire and install as

shown in Asm-R-0127.

ASSEMBLY

RX60/72/84 10/12 Assembly Section 3-10

ASSEMBLY

Front and Rear Deflectors (Standard Equipment)

Deflectors: Front and Rear Deflectors (Standard Equipment) are recommended for the average user and will

provide protection from thrown objects with proper operation under normal conditions. Deflectors must be

maintained in good repair or replaced after no more than two inches of wear off lower edge.

Front Deflector

Attach the Front Deflector to the Mower with 1/2” x

1-1/2” bolts, flatwashers, and locknuts.

Rear Deflector

Attach Deflectors to deck using 1/2” x 1-1/4” bolts

and locknuts

Front and Rear rubber-fabric Deflectors are Standard Equipment and Front and Rear Chain

Guards are optional . One type of guard must be installed (and maintained in good repair)

except for agricultural purposes only in areas where persons, vehicles, livestock, or other

property will not be endangered by thrown objects and where such safety equipment would

prevent the mower's reasonable performance of its assigned agricultural task. Assy01-

Shielding

ASSEMBLY

RX60/72/84 10/12 Assembly Section 3-11

ASSEMBLY

CHAIN GUARDS (Optional Equipment - All Models)

CHAIN GUARDS: Front and Rear Chain Guards (Optional Equipment) are recommended for higher than

normal usage (100 hours or more per year) and will provide protection from thrown objects with careful

operation. Chain Guards must be maintained in good repair by replacing missing or worn sections or by being

replaced when seriously worn or damaged.

Front Chain Guards

Attach Bracket to deck using 1/2” x 1-1/2” bolts (1),

and washers (3).

Rear Chain Guard

Attach Chainguard to deck using 1/2” x 1-1/2” bolts

(2), flatwashers (3) and locknuts (4).

ASSEMBLY

RX60/72/84 10/12 Assembly Section 3-12

ASSEMBLY

HYDRAULIC OR MANUAL LIFT (Model RX84 Only)

Install the Hydraulic Cylinder or the manual Ratchet Lift Screw (Asm-0039) between the Axle Center Lug and

the Lug directly behind the Center Gearbox. Install cylinder pins provided and retain with cotter pins. NOTE:

Figure ASM-0038 shows optional spring shock installation.

CHECK CHAINS (Extra Equipment)

Check chains are available for attachment to front of cutter as an accessory. Check chains are used to control

cut height and especially allows cutter to always be lowered to the same preset cut height.

Drill a 11/16” hole through each lifting lug 2-1/2” below the lift pins and 5/8” from the front of the lug.

Install lower end of check chain (1) to hitch ears, through lower holes using bolts (2), washers (3) and locknuts

(4). Tighten securely.

Install chain lugs (5) on either side of tractor top link mounting using bolt or pin of required diameter and length.

Cat. I kit requires a 3/4” diameter bolt.

Cutting height is then set by placing proper chain link in keyhole slot. Cutting height is easily adjusted by

hooking chain higher or lower in the keyhole brackets.

Tractor attaches with Top Link Pin.

NOTE: For additional safety in transport, raise mower as high as possible without allowing the driveline to

contact the deck, and shorten the chains as much as possible to prevent inadvertent falling in transport.

NOTE: RX60 and RX72 units use a Cat I Kit and RX84 Units use a Cat II Kit.

ASSEMBLY

RX60/72/84 10/12 Assembly Section 3-13

ASSEMBLY

OFFSET ADAPTER HITCH (EXTRA EQUIPMENT)

1. Fasten the Offset Adapter Hitch Weldment to the lift lugs using the Hitch Pin holes. Fasten the Adjustable

Leg to the left side lug if the Mower is to offset to the left. The Mower will make a cleaner cut behind the

wheel tracks if it is offset to the left. Reverse the Assembly for right offset.

2. Install the Brace Bars. Fasten the chain end to the rear mounting hole in the Gearbox Base Plate. Adjust

the Brace Bar so the Hitch Assembly is nearly perpendicular.

3. Attach the Mower to the tractor. Install stabilizer bars or adjust sway chains to prevent side sway of the

mower.

Stabilizer Bars or Sway Chains must be installed and adjusted tightly. Without these bars or

chains, serious damage to the Driveline can occur, and broken parts could cause bodily

injury to the operator or bystanders. Stabilizer Bars or Sway Chains are available at most

tractor dealerships.

4. Raise the mower to check clearance between the Driveline and Mower Deck. Set the lift stop on the tractor

to ascertain that the Driveline does not strike the deck.

For additional safety in transport, raise mower as high as possible without having driveline

hit deck and shorten check chains as much as possible to prevent inadvertent falling in

transport.

Operation Section 4-1

OPERATION SECTION

OPERATION

RX60/72/84 10/12 Operation Section 4-2

OPERATION

ALAMO INDUSTRIAL RX60/72/84 ROTARY MOWER

OPERATION INSTRUCTIONS

Alamo Industrial mowers are manufactured with quality material by skilled workers. These mowers are

designed to cut grass, weeds, small brush and other vegetative material up to 2-1/2” diameter in areas such as

pastures, industrial areas, and roadsides. The mower is equipped with protective deflectors and/or chain

guards to prevent objects being thrown from the mower by the blades, however, no shielding is 100% effective.

All shields, guards, deflectors, and chains equipped on the unit must be maintained on the mower in good

operational condition.

It is the operator’s responsibility to be knowledgeable of all potential operating hazards and to take every

reasonable precaution to ensure oneself, others, animals, and property are not injured or damaged by the

mower, tractor, or a thrown object. Do not operate the mower if passersby, pets, livestock, or property are

within 300 feet of the unit unless:

• All THROWN OBJECT SHIELDING including, Front and Rear Deflectors, Chains Guards, Steel Guards,

Bands, Side Skirts and Skid Shoes in place and in good condition when mowing.

• Mower sections or wing are adjusted to be close and parallel to ground without exposing blades.

• MOWING AREA has been inspected and foreign materials and debris have been removed.

• PASSERSBY are inside enclosed vehicle.

This section of the Operator’s Manual is designed to familiarize, instruct, and educate safe and proper mower

use to the operator. Pictures contained in this section are intended to be used as a visual aid to assist in

explaining the operation of a rotary mower. Some pictures may show shields removed for purposes of clarity.

NEVER OPERATE this implement without all shields in place and in good operational condition. The operator

must be familiar with the mower and tractor operation and all associated safety practices before operating the

mower and tractor. Proper operation of the mower, as detailed in this manual, will help ensure years of safe

and satisfactory use of the mower.

IMPORTANT: To avoid mower damage, retorque all bolts after the first 10 hours of operation. Retighten blade

carrier retaining nut on gearbox lower shaft to 600 ft. lbs.

READ AND UNDERSTAND THE ENTIRE OPERATING INSTRUCTIONS AND SAFETY SECTION OF THIS

MANUAL AND THE TRACTOR MANUAL BEFORE ATTEMPTING TO USE THE TRACTOR AND

IMPLEMENT. If you do not understand any of the instructions, contact your nearest authorized dealer for a

full explanation. Pay close attention to all safety signs and safety messages contained in this manual and

those affixed to the implement and tractor. OPS-U- 0001

READ, UNDERSTAND, and FOLLOW the following Safety Messages. Serious injury or

death may occur unless care is taken to follow the warnings and instructions stated in the

Safety Messages. Always use good common sense to avoid hazards.

(SG-2)

Si no lee ingles, pida ayuda a alguien que si lo lea para que le traduzca las

medidas de seguridad.

(SG-3)

OPERATION

RX60/72/84 10/12 Operation Section 4-3

OPERATION

1. OPERATOR REQUIREMENTS

Safe operation of the unit is the responsibility of a qualified operator. A qualified operator has read and

understands the implement and tractor Operator’s Manuals and is experienced in implement and tractor

operation and all associated safety practices. In addition to the safety messages contained in this manual,

safety signs are affixed to the implement and tractor. If any part of the operation and safe use of this

equipment is not completely understood, consult an authorized dealer for a complete explanation.

If the operator cannot read the manuals for themselves or does not completely understand the operation of the

equipment, it is the responsibility of the supervisor to read and explain the manuals, safety practices, and

operating instructions to the operator.

Safe operation of equipment requires that the operator wear approved Personal Protective Equipment (PPE)

for the job conditions when attaching, operating, servicing, and repairing the equipment. PPE is designed to

provide operator protection and includes the following safety wear:

PERSONAL PROTECTIVE EQUIPMENT (PPE)

• Always Wear Safety Glasses

•Hard Hat

• Steel Toe Safety Footwear

• Gloves

• Hearing Protection

• Close Fitting Clothing

• Respirator or Filter Mask (depends on

operating conditions) OPS-U- 0002

DO NOT use drugs or alcohol immediately before or while operating the

Tractor and Implement. Drugs and alcohol will affect an operator’s

alertness and coordination and therefore affect the operator’s ability to

operate the equipment safely. Before operating the Tractor or Implement,

an operator on prescription or over-the-counter medication must consult

a medical professional regarding any side effects of the medication that

would hinder their ability to operate the Equipment safely. NEVER

knowingly allow anyone to operate this equipment when their alertness or

coordination is impaired. Serious injury or death to the operator or others

could result if the operator is under the influence of drugs or alcohol.

(SG-27)

OPERATION

RX60/72/84 10/12 Operation Section 4-4

OPERATION

2. TRACTOR REQUIREMENTS

The tractor used to operate the mower must have the power capacity to lift, pull, and operate the Power Take

Off (PTO) at the mower’s rated speed while traveling at a ground speed between 2 and 5 MPH. Operating the

mower with a tractor that does not meet the following requirements may cause tractor or mower damage and

be a potential danger to the operator and passersby.

Tractor Requirements and Capabilities

• ASABE approved Roll-Over Protective Structure (ROPS) or ROPS cab and seat belt.

• Tractor Safety Devices ..................... Slow Moving Vehicle (SMV) emblem, lighting, PTO master shield

• Tractor Horsepower:......................... RX60 Mower RX72 Mower RX84 Mower

-Minimum .................. 35 HP 45 HP Lift 60 HP, Pull 30 HP

-Maximum.................. 90 HP 100 HP 100 HP

• Hitch -Lift Type Mower:

- Lifting Capacity ........ 1000 lbs. 1200 lbs. 1300 lbs.

- 3-Point Hitch............ CAT I or CAT ll CAT l or CAT ll CAT II or CAT III

• Front End Weight ............................. --------As needed to maintain 20% weight on front axle--------

• Power Take Off................................. 540 RPM 6-spline 540 RPM 6-Spline 540 RPM 6-Spline or

1000 RPM 21-Spline

2.1 ROPS and Seat Belt

The tractor must be equipped with a Roll-Over-Protective-Structure (ROPS) (tractor cab or roll-bar) and seat

belt to protect the operator from falling off the tractor, especially during a roll over where the driver could be

crushed and killed. Only operate the tractor with the ROPS in the raised position and seat belt fastened.

Tractor models not equipped with a ROPS and seat belt should have these life saving features installed by an

authorized dealer. OPS-U- 0003

Operate this Equipment only with a Tractor equipped with an approved roll-

over-protective system (ROPS). Always wear seat belts. Serious injury or

even death could result from falling off the tractor--particularly during a turnover

when the operator could be pinned under the ROPS.

(SG-7)

2.2 Tractor Safety Devices

If transporting or operating the tractor and implement near a public roadway, the tractor must be equipped with

proper warning lighting and a Slow Moving Vehicle (SMV) emblem which are clearly visible from the rear of

the unit. Lights and a SMV emblem must be equipped directly on implements if the visibility of the tractor

warning signals are obscured.

Maintain all manufacturer equipped safety shields and guards. Always replace shields and guards that were

removed for access to connect, service, or repair the tractor or implement. Never operate the tractor PTO

with the PTO master shield missing or in the raised position. OPS-U- 0004

OPERATION

RX60/72/84 10/12 Operation Section 4-5

OPERATION

2.3 Tractor Horsepower

The power required to operate a mower is determined by the tractor PTO horsepower. For most mowing

conditions, the RX60 mower requires a tractor with at least 35 HP, the RX72 mower requires a tractor with at

least 45 HP and the RX84 mower requires a tractor with at least 65 HP. Operating the mower with a tractor that

does not have adequate power may damage the tractor engine. Exceeding 90 HP (Model RX60) and 100 HP

(Model RX72 & RX84) may cause mower damage by overpowering the unit in heavy cutting conditions.

2.4 3-Point Hitch

The tractor 3-point hitch must be rated to lift at least

1000 lbs. (Model RX60), 1200 lbs. (Model RX72)

and 1500 lbs. (Model RX84). The Model RX84 is

designed to be mounted on a tractor with CAT II or

CAT III 3-Point or CAT III Quick Hitch.

Refer to the tractor operator’s manual for the

category of the tractor being used. If the hitch does

not conform to ASABE dimensions, the mower may

not fit or raise properly. Consult an authorized

dealer for possible modification procedures to

mount non-conforming hitches.

Depending on the hitch category, certain size pins

are used to attach the mower to the tractor. CAT I

hitches require 7/8” lower and 3/4” upper diameter

hitch pins. Quick Hitch requires 1-7/16” diameter

lower pin and 1-1/4” diameter upper pin. CAT II

hitches require 1-1/8” lower pins and 1 inch upper

pins. CAT III hitches require 1-7/16” lower pins and

1-1/4” upper pin diameters.

Our 3-Point Quick Hitch is designed to connect to a

Quick-Attach coupler making mounting and

dismounting your mower easier. The 3-Point Quick

Hitch is also designed to connect the mower to a

tractor’s 3-point linkage without the use of a Quick-

Attach Coupler.

2.5 Front End Weight

A minimum of 20% total tractor weight must be maintained on the tractor front end at all times. Front end

weight is critical to maintain steering control and to prevent the tractor from rearing up while driving. If the

front end is too light, add weight until a minimum of 20% total weight is reached on the front tires. Front

weights and weight carriers can be purchased through an authorized tractor dealership. OPS-U- 0005

OPERATION

RX60/72/84 10/12 Operation Section 4-6

OPERATION

2.6 Drawbar-Pull Type Mower

For equipment operating at 540 RPM, the tractor

drawbar must be positioned at a 14” distance from the

hitch point to the PTO shaft end for proper operation

and minimal wear to the driveline.

If attaching the mower tongue clevis to a 3-point hitch drawbar supported by the lower lift arms, the attaching

point must be extended past the main bar to allow for turning without binding the clevis and bar. Lift arm

stabilizers must be used with this type of drawbar to prevent the mower from swaying from side to side.

OPS-R- 0061

2.7 Power Take Off (PTO)

This mower is designed to operate at a PTO speed of 540. Most tractors operate at either 540, or a

combination of 540 and 1000 RPM PTO speeds. The operating speed of the mower and tractor can be

determined by the number of splines on the driveline yoke and PTO output shaft. Those operating at 540 RPM

will have a 6-spline shaft and those operating at 1000 RPM will have a 21-spline shaft. Note: Only the 284

mower can be ordered to operate on tractors equipped with a 1000 RPM 21-spline shaft. Refer to the tractor

owner’s manual for instructions to change PTO speeds on models that operate at more than one speed.

If operating an older model tractor where the tractor’s transmission and PTO utilize one master clutch, an

over-running clutch must be used between the PTO output shaft and the driveline of the mower. An authorized

tractor dealer can provide the over-running clutch and its installation if needed. OPS-R- 0066_A

OPERATION

RX60/72/84 10/12 Operation Section 4-7

OPERATION

Do not connect the PTO driveline to the tractor or operate the implement unless the

implement is securely connected to the tractor.

DO NOT use a PTO adapter to attach a non-matching Implement driveline to a Tractor

PTO. Use of an adapter can double the operating speed of the Implement resulting in

excessive vibration, thrown objects, and blade and implement failure. Adapter use will also

change the working length of the driveline exposing unshielded driveline areas. Serious

bodily injury and/or equipment failure can result from using a PTO adapter. Consult an

authorized dealer for assistance if the Implement driveline does not match the Tractor PTO.

(S3PT-14)

Never operate the Tractor and Mower if the Implement input driveline is directly connected

to the Tractor transmission. Tractor braking distances can be substantially increased by

the momentum of the rotating Mower blades driving the Tractor transmission even though

the Tractor clutch has been disengaged. Install an over running clutch between the Tractor

PTO and the Mower driveline to prevent this potentially dangerous situation.

(S3PT-16)

2.8 Tire Spacing

Tractor tires should be set a minimum of 60”(1.5

mm) apart measured from inside of tire to inside of

tire. Refer to the tractor Operator’s Manual or

consult an authorized dealer for instructions to

change tractor tire spacing. OPS-R- 0062

3. GETTING ON AND OFF THE TRACTOR

Before getting onto the tractor, the operator must read and completely understand the implement and tractor

operator manuals. If any part of either manual is not completely understood, consult an authorized dealer for

a complete explanation. OPS-U- 0007

Do not mount or dismount the Tractor while the tractor is moving. Mount

the Tractor only when the Tractor and all moving parts are completely

stopped.

(SG-12)

OPERATION

RX60/72/84 10/12 Operation Section 4-8

OPERATION

3.1 Boarding the Tractor

Use both hands and equipped handrails and steps for support when boarding the tractor. Never use control

levers for support when mounting the tractor. Seat yourself in the operator’s seat and secure the seat belt

around you.

Never allow passengers to ride on the tractor or attached equipment. Riders can easily fall off and be

seriously injured or killed from falling off and being ran over. It is the operator’s responsibility to forbid all extra

riders at all times. OPS-U- 0008

Never allow children to operate, ride on, or come close to the Tractor or

Implement. Usually, 16-17 year-old children who are mature and

responsible can operate the implement with adult supervision, if they

have read and understand the Operator’s Manuals, been trained in

proper operation of the tractor and Implement, and are physically large

enough to reach and operate the controls easily.

(SG-11)

Never allow children or other persons to ride on the Tractor or Implement.

Falling off can result in serious injury or death.

(SG-10)

3.2 Dismounting the Tractor

Before dismounting, park the tractor and implement on a reasonably level surface, apply the parking brake,

idle the engine down, disengage the PTO, and lower the implement to the ground. Shut down the tractor

engine according to the operator’s manual, remove the key, and wait for all motion to completely stop. Never

leave the seat until the tractor, its engine and all moving parts have come to a complete stop.

Use hand rails and steps when exiting the tractor. Be careful of your step and use extra caution when mud,

ice, snow or other matter has accumulated on the steps or hand rails. Use all handrails and steps for support

and never rush or jump off the tractor. OPS-U- 0009

BEFORE leaving the tractor seat lower the implement, set the parking

brake and/or set the tractor transmission in parking gear, disengage the

PTO, stop the engine, remove the key, and wait for all moving parts to

stop. Place the tractor shift lever into a low range or parking gear to

prevent the tractor from rolling. Never dismount a Tractor that is moving

or while the engine is running. Operate the Tractor controls from the

tractor seat only.

(SG-9)

OPERATION

RX60/72/84 10/12 Operation Section 4-9

OPERATION

4. STARTING THE TRACTOR

The operator must have a complete understanding of the placement, function, and operational use of all

tractor controls before starting the tractor. Review the tractor operator’s manual and consult an authorized

dealer for tractor operation instructions if needed.

Essential Tractor Controls:

• Locate the light control switch.

• Locate the engine shut off control.

• Locate the brake pedals and the clutch.

• Locate the PTO control.

• Locate the 3-point hitch control lever.

• Locate the hydraulic remote control levers.

Before starting the tractor ensure the following:

• Conduct all pre-start operation inspection and service according to the tractor operator’s manual.

• Make sure all guards, shields, and other safety devices are securely in place.

• The parking brake is on.

• The PTO control lever is disengaged.

• The 3-point hitch control lever is in the lowered position.

• The hydraulic remote control levers are in the neutral position.

• The tractor transmission levers are in park or neutral.

Refer to the tractor owner’s manual for tractor starting procedures. Only start the tractor while seated and

belted in the tractor operator’s seat. Never bypass the ignition switch by short circuiting the starter solenoid.

After the tractor engine is running, avoid accidental contact with the tractor transmission to prevent sudden

and unexpected tractor movement. OPS-U-0028

Never run the Tractor engine in a closed building or without adequate ventilation. The

exhaust fumes can be hazardous to your health.

(SG-23)

Start tractor only when properly seated in the Tractor seat. Starting a

tractor in gear can result in injury or death. Read the Tractor operators

manual for proper starting instructions.

(SG-13)

5. CONNECTING THE MOWER TO THE TRACTOR

Use extreme caution when connecting the mower to the tractor. The mower should be securely resting at

ground level or setting on blocks. Keep hands and feet from under the mower deck and clear of pinch points

between the tractor hitch arms and mower pins. OPS-R-0001

Always shut the Tractor completely down, place the transmission in park, and set the

parking brake before you or anyone else attempts to connect or disconnect the Implement

and Tractor hitches.

(S3PT-15)

OPERATION

RX60/72/84 10/12 Operation Section 4-10

OPERATION

5.1 Connecting the Mower-Lift Type

1. Make sure the tractor is equipped with the

correct PTO shaft. Change shafts if needed.

2. Shorten or remove the tractor drawbar to avoid

interference when raising and lowering the

mower.

3. Board the tractor and start the engine. Position

the tractor to the mower with the 3-point lift

arms positioned at the same height and to the

outside of the mower hitch pins. Note: Set the

3-point lift control to “Position Control” so that

the lift arms maintain a constant height when

attaching the mower. See the tractor Operator’s

Manual for correct settings when attaching 3-

point equipment.

4. Turn off the tractor engine and dismount.

5. One lift arm at a time, align arm end hole

between the set of A-frame lift lugs. Insert hitch

pin through the lug and arm holes and insert

retaining pin into hitch pin.

6. Walk around to opposite side and repeat

procedure for remaining lift arm and hitch pin.

7. Extend or retract 3-point top link to align its end

hole with the holes of the mower’s top link.

Insert the top link hitch pin and insert retaining

pin into hitch pin.

8. Adjust any lower link check chains, guide

blocks, or sway blocks to prevent the mower

from swaying side to side and possible contact

with tractor rear tires.

NOTE: Offset Adaptor Hitches are available to position the mower to the left or right. Mowers with Offset

Adaptor hitches connect to the 3-Point hitch the same way as the mower A-frame. See Offset Adaptor Hitch in

the Assembly Section for details to equip the mower with this feature.

5.2 3-Point Quick Hitch

Our 3-Point Quick Hitch is designed to connect to a

Quick-Attach Coupler making mounting and

dismounting your mower easier. The 3-Point Quick

Hitch is also designed to connect the cutter to a

tractor’s three-point linkage without the use of a

Quick-Attach Coupler.

OPERATION

RX60/72/84 10/12 Operation Section 4-11

OPERATION

5.3 Connecting Mower - Lift Type (Quick Hitch)

Crushing Hazard between Quick-Hitch and Implement. Do not allow anyone to stand

between the Quick-Hitch and implement during hook-up operations. Never operate the

hydraulic 3-point lift controls while someone is directly behind the tractor.

1. Make certain the implement’s upper and lower

hitch pins are secured.

2. Lower the tractor’s 3-point lift until the three

Quick-Hitch hooks are lower than the

implements hitch pins. Carefully back the

tractor to align the Quick-Hitch hooks under the

implement’s hitch pins.

3. Slowly raise the tractor’s 3-point lift until the

lower Quick-hitch hooks lock into place over the

implement’s 3-point hitch pins.

IMPORTANT: Make certain the implement’s top 3-

point hitch pin is captured by the Quick-Hitch top 3-

point hook. If not consult your Quick Hitch manual

for required adjustment.

IMPORTANT: The Quick Hitch will move mower

further from tractor which will require checking the

following:

1. Driveline length

2. Tractor stability

NOTE: Offset Adapter Hitches are available to

position the mower to the left or right. Mowers with

Offset Adapter Hitches connect to the 3-point hitch

the same way as the mower A-frame. See Offset

Adapter Hitch in the Assembly Section for details to

equip the mower with this feature.

5.4 Safety Tow Chain

If the mower is towed on a public roadway, a safety chain with tensile strength equal to or greater than the

gross weight of the mower must be connected between the tractor and mower. This will help control the

implement in the event the tongue becomes disconnected from the drawbar. Make sure the chain is attached

to a secure location on the tractor and not to an intermediate support.

After connecting both ends of the safety chain, drive the tractor to the right and left to check for proper chain

length. Adjust length as necessary and allow only enough slack in the chain to make a maximum turn in both

directions. When not in use, store the safety chain to protect it from mud or standing water by wrapping the

chain around the tongue. Replace the safety chain if one or more links or end fittings are broken, stretched or

otherwise damaged or deformed. OPS-U-0039

OPERATION

RX60/72/84 10/12 Operation Section 4-12

OPERATION

6.1 Setting Mower Height- Lift Type - (Standard or Quick Hitch)

1. Park the tractor and mower on level ground.

2. Using the 3-point hitch control lever, position

the front of the mower with the side skids 1”

less off the ground than desired cut height. For

example, for a 3” cut, position the skids 2” from

the ground. Set the 3-point control lever stop at

this position to maintain this height when

raising and lowering the mower.

3. Shut down the tractor and remove the key.

4. Adjust the mower deck front to rear by

extending or retracting the 3-point top link.

Always set front of deck 3/4” lower than rear for

best performance.

IMPORTANT: Scan this QR Code with your smart phone to link to the PAMI Safe

Implement Hitching Manual for more information on correctly connecting

agricultural tractors to implements. Or type in your internet browser the following

web address: www.algqr.com/hme

Ops-0008-MISC

6. SETTING THE MOWER

Properly setting the cutting height is essential for efficient and safe operation. A properly set mower will make

a more uniform cut, distribute clippings more evenly, require minimal tractor work, and follow the contour of

uneven terrain. NOTE: Avoid very low cutting heights, striking the ground with the blades gives the most

damaging shock loads and will cause damage to the mower and drive. Blades contacting the ground may

cause objects to be thrown out from under the mower deck. Always avoid operating the mower at a height

which causes the blades to contact the ground. OPS-U- 0010

Never work under the Implement, the framework, or any lifted

component unless the Implement is securely supported or blocked up

to prevent sudden or inadvertent falling which could cause serious

injury or even death.

(SG-14)

OPERATION

RX60/72/84 10/12 Operation Section 4-13

OPERATION

5. Level the mower side to side by manipulating

one lower lift arm length. On most tractors, at

least one of the lift arms is designed to allow for

manipulation of its length. Shortening or

extending will allow for deck leveling from side

to side.

6. Securely block up the mower at this height.

7. Remove the bolts securing the tailwheel beam

in position and allow the tailwheel to rest at

ground level. Align tailwheel beam between

nearest sets of holes in beam support brackets

and reinstall support bolts on each side of

beam. Tighten all bolts and nuts.

8. Extend the tractor’s top 3-point link so that

when lifting the mower, the front of the deck will

raise 2 to 2½” before the tail wheel leaves the

ground. This will allow the mower to follow the

contour of uneven terrain.

Note: Install optional check chains when there is a

problem with the hydraulic 3-Point lift maintaining a

set height or when a constant pre-adjusted cut

height is required. See Check Chains in the

Assembly Section for this accessory.

OPERATION

RX60/72/84 10/12 Operation Section 4-14

OPERATION

6.2 Connecting the Mower-Pull Type

1. Make sure the tractor is equipped with the

correct PTO shaft and the drawbar is extended

14” from the end of the PTO shaft to the hitch

point.

2. Block the mower wheels in place and use the

attached parking jack to raise or lower the

tongue clevis to the height of the tractor

drawbar. The parking jack can be rotated 15

degrees in each direction to obtain a near

vertical position. Note: Always place jack foot on

firm surface or place board under jack for

support.

3. Board the tractor and start the engine. Back the

tractor to the mower aligning the drawbar hitch

hole with the mower hitch clevis. Turn off the

engine, secure the tractor in position, and

dismount.

4. To attach the mower, place two 1” flatwashers

(1) positioned under top lip of tongue clevis and

to the top of drawbar. Add additional 1”

flatwashers (2) between the bottom of drawbar

and bottom lip of clevis to fill open space. Insert

a 3/4” x 4-1/2” grade 5 or 8 bolt (3) through

clevis and drawbar and retain in position with a

1” locknut (4). The bolt and locknut should be

tightened securely to support the tongue

properly without springing of breaking the

clevis. Never attach mower to the tractor with a

pin not having a nut.

5. Securely attach mower safety chain from

mower tongue to tractor drawbar or drawbar

support frame.

6. Lower the jack until the tongue is completely

supported by the drawbar. Remove jack from

the tongue and place on storage bracket of

mower main frame.

7. If using a hydraulic cylinder, connect hydraulic

hose ends into tractor hydraulic ports. Pressure

may need to be relieved from the system to

allow for ease of attachment.

8. If the mower has been attached to a 3-point

hitch drawbar, adjust any tractor equipped

lower link check chains, guide blocks, or sway

blocks to prevent the hitch and mower from

swaying side to side. Note: Never raise the 3-

point lift with the mower attached as

catastrophic driveline damage will occur.

OPERATION

RX60/72/84 10/12 Operation Section 4-15

OPERATION

6.3 Setting Mowing Height-Pull Type

1. Park the tractor and mower on level ground.

2. Using the tailwheel ratchet jack or hydraulic

cylinder, position the mower so the skid shoes

are 1” less off the ground than the desired final

cut height. For example, if a 3” cut is desired,

raise or lower the mower until the skid shoes

are 2” off the ground. If a hydraulic cylinder is

used, stroke control spacers can be placed on

the hydraulic shaft to maintain a set cutting

height each time the mower is raised and

lowered.

3. Adjust the mower leveling rod so that the front

of the mower is approximately 3/4” lower than

the rear.

If the mower is attached to a 3-point hitch drawbar,

adjust any tractor equipped lower link check chains,

guide blocks, or sway blocks to prevent the hitch

and mower from swaying from side to side. Never

raise the 3-point lift with the mower attached as

catastrophic driveline damage will occur.

OPERATION

RX60/72/84 10/12 Operation Section 4-16

OPERATION

6.4 Setting Deck Pitch

Lower Horse Power - Better Fuel Efficiency

To increase fuel efficiency and lower horsepower

requirements for mower operation, the mower

should be operated with the deck approximately

3/4" LOWER IN THE FRONT THAN THE REAR.

Operating the mower at this pitch will allow the

mower to cut the grass only once and requires less

work from the tractor.

Increase Mulching

To increase mulching of the grass or crop material

during mower operation, the mower should be

operated with the deck approximately 3/4" HIGHER

IN THE FRONT THAN THE REAR.

Operating the mower at this pitch will allow the

mower to cut the grass twice and can result in a

more even cut and improved distribution of the cut

material.

IMPORTANT:

Adjust the leveling rods the same amount and

maintain equal tension in the rods. Improper

adjustment may cause rods to snap or bend.

Retighten the jamnuts after the deck pitch has been

set. OPS-U-0041

7. DRIVELINE ATTACHMENT

The driveline yoke and tractor PTO shaft must be

dirt free and greased for attachment.

To connect the mower driveline to the tractor PTO

output shaft, pull the driveline yoke collar back and

align the grooves and splines of the yoke with those

of the PTO shaft. Push the driveline yoke onto the

PTO shaft, release the locking collar, and position

the yoke until the locking collar balls are seated

onto the PTO shaft. Push and pull the driveline

back and forth several times to ensure a secure

attachment. OPS-R-0003_A

OPERATION

RX60/72/84 10/12 Operation Section 4-17

OPERATION

7.1 Driveline Length Check

When fitting the mower to the tractor, the telescoping driveline must be inspected to ensure that at its most

compressed position, the profiles do not “bottom out”, and when at its farthest extended position, there is

sufficient engagement between the profiles to operate safely. At its shortest length, there must be at least a 1”

clearance between each profile end and opposite profile universal joint. At its farthest operating extension, a

minimum profile engagement of 6” must be maintained.

When attaching the Implement input driveline to the Tractor PTO, it is important that the

connecting yoke spring activated locking collar slides freely and the locking balls are seated

securely in the groove on the Tractor PTO shaft. Push and pull the driveline back and forth

several times to ensure it is securely attached. A driveline not attached correctly to the

Tractor PTO shaft could come loose and result in personal injury and damage to the

Implement.

(S3PT-17)

Before operating the Implement, check to make sure the Implement input driveline will not

bottom out or become disengaged. Bottoming out occurs when the inner shaft penetrates

the outer housing until the assembly becomes solid-it can shorten no more. Bottoming out

can cause serious damage to the Tractor PTO by pushing the PTO into the Tractor and

through the support bearings or downward onto the PTO shaft, breaking it off. A broken

driveline can cause personal injury.

(S3PT-18)

“Bottoming Out” Check Procedure

• Disconnect driveline from the tractor and slide

the profiles together until fully compressed.

• Place a mark on the inner shield 1/8” from the

end of the outer shield.

• Reattach the driveline to the PTO Shaft.

• Raise the mower. Drive through a typical ditch

which the unit may encounter and watch marks

on the driveline. If the distance between the

mark and the outer shield becomes less than 2”

at any point there is a potential problem

bottoming out the driveline and the driveline

should be shortened. OPS-R-0004_F

OPERATION

RX60/72/84 10/12 Operation Section 4-18

OPERATION

Shorten the driveline profiles as follows:

• Remove the driveline from the tractor.

• Raise and lower the mower to find the position

with the shortest distance between the tractor

PTO shaft and cutter gearbox. Shut down the

tractor and securely block the mower in this

position.

• Pull driveline apart and reattach yoke to PTO

shaft.

• Hold driveline sections parallel to one another

and measure back 1” from yoke of each shaft

and place mark on opposite section. Cut this

length off with a saw.

• Round off all sharp edges and debur.

• Thoroughly grease then reinstall the driveline.

• Recheck for proper operation.

Engagement Check Procedure

• With the driveline attached, raise and lower the mower within its operating range. Position the mower to

the point where the telescoping driveline is at its maximum extension. Completely shut down the tractor

and secure in position.

• Mark the inner driveline shield 1/8” from the end of the outer shield.

• Disconnect the driveline from the tractor and separate the two driveline halves.

• Measure the distance from the mark to the end of the inner profile. This length is the amount the driveline

profiles were engaged.

• If the engaged length is less than 9”, the shaft is considered too short and should be replaced with a longer

shaft. Consult an authorized dealer to purchase the required driveline length.

NOTE: When raising the mower, at least 1” clearance must be maintained between the driveline and the

mower deck. If necessary, place an upper lift stop on the 3-point hitch control lever to limit the height the

mower can be raised. OPS-R-0005_E

8. PRE-OPERATION INSPECTION AND SERVICE

Before each use, a pre-operation inspection and service of the implement and tractor must be performed.

This includes routine maintenance and scheduled lubrication, inspecting that all safety devices are equipped

and functional, and performing needed repairs. DO NOT operate the unit if the pre-operation inspection

reveals any condition affecting safe operation. Perform repairs and replacement of damaged and missing

parts as soon as noticed. By performing a thorough pre-operation inspection and service, valuable down time

and repair cost can be avoided. OPS-U-0029

Always disconnect the main PTO Driveline from the Tractor before performing service on

the Implement. Never work on the Implement with the tractor PTO driveline connected and

running. Rotating Parts, Blades or Drivelines could turn without warning and cause

immediate entanglement, injury or death.

(S3PT-11)

OPERATION

RX60/72/84 10/12 Operation Section 4-19

OPERATION

Periodically inspect all moving parts for wear and replace when

necessary with authorized service parts. Look for loose fasteners, worn

or broken parts, and leaky or loose fittings. Make sure all pins have

cotter pins and washers. Serious injury may occur from not maintaining

this machine in good working order.

(SG-21)

8.1 Tractor Pre-Operation Inspection/Service

Refer to the tractor operator’s manual to ensure a

complete pre-operation inspection and scheduled

service is performed according to the

manufacturers recommendations. The following

are some of the items that require daily service and

inspection:

• Tire condition/air pressure

• Wheel lug bolts

• Steering linkage

• PTO shield

• SMV sign is clean and visible

• Tractor’s lights are clean and functional

• Tractor Seat belt is in good condition

• Tractor ROPS is in good condition

• ROPS is in the raised position

• No tractor oil leaks

• Radiator free of debris

• Engine oil level and condition

• Engine coolant level and condition

• Power brake fluid level

• Power steering fluid level

• Fuel condition and level

• Sufficient lubrication at all lube points

• Air filter condition OPS-U-0030

8.2 Mower Pre-Operation Inspection/Service

Before each mower use, a complete inspection and service is required to ensure the mower is in a good and

safe working condition. Damaged and/or broken parts should be repaired and/or replaced immediately. To

ensure the mower is ready for operation, conduct the following. OPS-R-0007

OPERATION

RX60/72/84 10/12 Operation Section 4-20

OPERATION

The operator’s manual and safety signs affixed on

the unit contain important instructions on the safe

and proper use of the equipment. Maintain these

important safety features on the implement in good

condition to ensure the information is available to

the operator at all times.

• Ensure the manual canister is secured to the

equipment with the operator’s manual inside.

• Ensure all safety signs are in place and legible.

Replace missing, damaged, and illegible

decals. OPS-U- 0011

• Perform scheduled lubrication as detailed in

the maintenance section.

• Ensure all decals are in place and legible.

• Ensure the driveline is securely attached to

tractor. Make sure the driveline yoke locking

collar is securely seated in the grooves of the

PTO shaft by pushing and pulling the yoke

several times.

• Lift Type-Inspect that the 3-point hitch pins are

the proper size, correctly installed, and secured

to the tractor lift arms with retaining pins

inserted.

• Pull Type-Inspect that the hitch pin is the

correct size. OPS-R-0008_E

• Ensure deflectors and/or chainguards are in

position and not damaged. Replace worn,

broken, and missing pieces. OPS-R-0068

OPERATION

RX60/72/84 10/12 Operation Section 4-21

OPERATION

All Safety Shields, Guards and Safety devices including (but not

limited to) - the Deflectors, Chain Guards, Steel Guards, Gearbox

Shields, PTO integral shields, and Retractable Door Shields should

be used and maintained in good working condition. All safety

devices should be inspected carefully at least daily for missing or

broken components. Missing, broken, or worn items must be

replaced at once to reduce the possibility of injury or death from

thrown objects, entanglement, or blade contact.

(SGM-3)

• Lift Type-Ensure the tailwheel beam position

support bolts are properly installed and

tightened.

• Inspect all bolts and screws and tighten to the

recommended torque. OPS-R-0039_H

• Ensure the tractor PTO master shield and the

mower slip clutch shield are in place, lowered,

and in good condition.

• Ensure the driveline integral shield is in good

condition and rotates freely.

• Ensure the driveline slip clutch (if equipped) is

properly adjusted. OPS-R-0039

OPERATION

RX60/72/84 10/12 Operation Section 4-22

OPERATION

• Inspect the gearbox oil level. A low oil level is a

warning sign that the gearbox may be cracked

or its seal is damaged and needs replacement.

• Ensure the gearbox vent is in place and free

from clogs. OPS-R-0040_B

• Inspect blades and blade bolts for looseness

and excessive wear. Make sure the mower is

securely blocked up before crawling beneath.

Replace damaged, worn and missing blades as

complete sets to maintain rotary balance during

operation.

• Ensure blade pan nut is tightened with the

cotter pin inserted and spread. OPS-R-0041

OPERATION

RX60/72/84 10/12 Operation Section 4-23

OPERATION

8.3 Cutting Component Inspection

Inspect blade pan and blade assembly for the following:

OPS-U-0031

OPERATION

RX60/72/84 10/12 Operation Section 4-24

OPERATION

Operating the mower with loose blade hardware will damage the blade holder or blades and

can result in blade breakage or blade fastener failure. Broken blades or bolts can be thrown

out from under the mower for distances up to 300 feet. When the blades are replaced, the

fastening hardware must be replaced. Check and retighten the blade hardware after the

first eight hours of operation. In severe cutting conditions, recheck the blade carrier and

blade bolt torque every 50 hours.

To help prevent structural damage caused by loose hardware, tighten gearbox mounting

hardware as specified. Check the fastener torque after first 8 hours of use and every 50

hours thereafter.

OPERATION

RX60/72/84 10/12 Operation Section 4-25

OPERATION

Inspect the Blades daily for abnormal wear. REPLACE BOTH BLADES on that carrier

IMMEDIATELY if either blade has:

• Become bent or deformed from it’s original shape or

• Any cracks are visible, or

• Deep gouges in the blade’s surface are present, or

• Gouges or chipped areas in the cutting edge are larger than 1/2”(12.7mm), or

• The material on the leading edge has been worn away by more than 1/2(12.7mm)”

Failure to replace abnormally worn blades may lead to catastrophic failure of the blades and ejection of the

broken part with tremendous force which may cause serious bodily injury or death. OPS-U-0032

OPERATION

RX60/72/84 10/12 Operation Section 4-26

OPERATION

8.4 Blade Bolt Inspection

Inspect Blade Bolt Head daily for wear as followed:

Inspect the Blade Bolt Heads daily for abnormal wear. REPLACE BOTH BLADE BOLTS on

the Blades IMMEDIATELY if either blade bolts has:

• Visible cracks or

• If the recessed area on blade bolt is worn off or

• If Blade Bolt has gouges or chipped areas.

Failure to replace abnormally worn blade bolts may lead to catastrophic failure of the blades and ejection of

the broken part which may cause serious bodily injury or death.

Always replace Blade Bolts with new bolts whenever replacing the Blades. OPS-U-0037

OPERATION

RX60/72/84 10/12 Operation Section 4-27

OPERATION

Rotary Mower PRE-OPERATION Inspection

Mower ID#___________________

Date:________________________

Before conducting the inspection, make sure the tractor engine is off, all rotation has stopped

and the tractor is in park with the parking brake engaged. Make sure the mower is resting on

the ground or securely blocked up and all hydraulic pressure has been relieved.

Make:___________________________________ Shift:_____________________________________

Operator’s Signature:___________________________________________________________________________

Item

Condition at

Start of Shift

Specific Comments if

not O.K.

The Operator’s Manual is in the canister on the mower

All safety decals are in place and legible

The tongue/hitch connection bolts & pins are tight

There are no cracks in tongue or hitch

The tow chain is secured to the tractor & mower

The hydraulic cylinders pins are tight

There are no leaking or damaged hoses

The mower deck is clear of cut grass and debris

Chain guards/deflectors are in place & in good condition

Driveline/gearbox shields are in good condition

Driveline clutches are in good condition; not frozen

Driveline telescoping members & U-joints are lubricated

Driveline yokes are securely attached to PTO & mower

Gearbox mounting bolts are tight

Gearbox oil is at the proper level

Blade carrier retaining nut is tight

Blades are not chipped, cracked or bent

Blade bolts are tight

Wheel lug nuts are tight

Transport locks are in good condition

IMPORTANT: Scan this QR

Code for an electronic copy

of this inspection sheet.

DO NOT OPERATE an UNSAFE TRACTOR or MOWER

OPERATION

RX60/72/84 10/12 Operation Section 4-28

OPERATION

Tractor PRE-OPERATION Inspection

Mower ID#________________ Make ____________________

Date: ________________ Shift ____________________

Before conducting the inspection, make sure the tractor engine is off, all

rotation has stopped and the tractor is in park with the parking brake

engaged. Make sure the mower is resting on the ground or securely blocked

up and all hydraulic pressure has been relieved.

Operator’s Signature:

Item

Condition at

Start of Shift

Specific Comments if

not O.K.

The flashing lights function properly

The SMV Sign is clean and visible

The tires are in good condition with proper pressure

The wheel lug bolts are tight

The tractor brakes are in good condition

The steering linkage is in good condition

There are no visible oil leaks

The hydraulic controls function properly

The ROPS or ROPS Cab is in good condition

The seatbelt is in place and in good condition

The 3-point hitch is in good condition

The drawbar pins are securely in place

The PTO master shield is in place

The engine oil level is full

The brake fluid level is full

The power steering fluid level is full

The fuel level is adequate

The engine coolant fluid level is full

The radiator is free of debris

The air filter is in good condition

DO NOT OPERATE an UNSAFE TRACTOR or MOWER

This Inspection Form may be freely duplicated for extra copies.

OPERATION

RX60/72/84 10/12 Operation Section 4-29

OPERATION

9. DRIVING THE TRACTOR AND IMPLEMENT

Safe tractor transport requires the operator possess a thorough knowledge of the model being operated and

precautions to take while driving with an attached implement. Ensure the tractor has the capacity to handle the

weight of the implement and the tractor operating controls are set for safe transport. To ensure safety while

driving the tractor with an attached implement, review the following. OPS-U- 0012

Never run the Tractor engine in a closed building or without adequate ventilation. The

exhaust fumes can be hazardous to your health.

(SG-23)

Transport only at speeds where you can maintain control of the

equipment. Serious accidents and injuries can result from operating this

equipment at high speeds. Understand the Tractor and Implement and

how it handles before transporting on streets and highways. Make sure the Tractor steering

and brakes are in good condition and operate properly.

Before transporting the Tractor and Implement, determine the proper transport speeds for

you and the equipment. Make sure you abide by the following rules:

Test the tractor at a slow speed and increase the speed slowly. Apply the Brakes smoothly

to determine the stopping characteristics of the Tractor and Implement. As you increase

the speed of the Tractor the stopping distance increases. Determine the maximum

transport speed not to exceed 20 mph (30 kph) for transporting this equipment.

Test the equipment at a slow speed in turns. Increase the speed through the turn only after

you determine that the equipment can be operated at a higher speed. Use extreme care

and reduce your speed when turning sharply to prevent the tractor and implement from

turning over. Determine the maximum turning speed for you and this equipment before

operating on roads or uneven ground.

Only transport the Tractor and Implement at the speeds which allow you to properly control

the equipment.

Be aware of the operating conditions. Do not operate the Tractor with weak or faulty brakes

or worn tires. When operating down a hill or on wet or rain slick roads, the braking distance

increases: use extreme care and reduce your speed. When operating in traffic always use

the Tractor’s flashing warning lights and reduce your speed. Be aware of traffic around you

and watch out for the other guy.

(SG-19)

OPERATION

RX60/72/84 10/12 Operation Section 4-30

OPERATION

9.1 Starting the Tractor

The procedure to start the tractor is model specific.

Refer to the tractor operator’s manual for starting

procedures for your particular tractor. Consult an

authorized dealer if the starting procedure is

unclear. Ensure the 3-point control lever is in the

lowered position and the PTO is disengaged before

starting the tractor. OPS-U-0033

9.2 Brake and Differential Lock Setting

Make sure the tractor brakes are in good operating

condition. Tractor brakes can be set to operate

independently allowing single rear wheel braking

action or locked together to provide simultaneous

rear wheel braking. FOR MOST DRIVING AND

OPERATING CONDITIONS, THE BRAKE PEDALS

SHOULD BE LOCKED TOGETHER TO PROVIDE

THE MOST EFFECTIVE BRAKING ACTION.

Always disengage the tractor differential lock when

turning. When engaged the differential lock will

prevent or limit the tractor from turning. During

normal cutting conditions, locking the differential

provides no benefit and should not be used. OPS-

U- 0013

Be aware of the operating conditions. Do not operate the Tractor with weak or faulty brakes.

When operating down a hill or on wet or rain slick roads, the braking distance increases; use

extreme care and reduce your speed in these conditions. When operating in traffic, always

use the Tractor’s flashing warning lights and reduce your speed. Be aware of traffic around

you and watch out for the other guy.

OPERATION

RX60/72/84 10/12 Operation Section 4-31

OPERATION

9.3 Raising the Mower

Using the tractor 3-point hitch control lever, raise

the mower off the ground about 6”, or just high

enough to clear any ground obstacles. When

raising the mower, make sure all connection points

are securely attached and at least 1” clearance is

maintained between the driveline and the deck. If

necessary, place an upper lift stop on the 3-point

hitch control lever to limit the height the mower can

be raised to avoid driveline damage

. OPS-R-0042

9.4 Driving the Tractor and Mower

Start off driving at a slow speed and gradually increase your speed while maintaining complete control of the

tractor and mower. Moving slowly at first will also prevent the tractor from rearing up and loss of steering

control. The tractor should never be operated at speeds that cannot be safely handled or which will prevent

the operator from stopping quickly during an emergency. If the power steering or engine ceases operating,

stop the tractor immediately as the tractor will be difficult to control.

Perform turns with the tractor and mower at slow

speeds to determine how the tractor with an

attached mower handles a turn. Determine the

safe speed to maintain proper control of the tractor

when making turns. When turning with a towed

implement, the overall working length of the unit is

increased. Allow additional clearance for the

mower when turning.

To avoid overturns, drive the tractor with care and

at safe speeds, especially when operating over

rough ground, crossing ditches or slopes, and

turning corners. Tractor wheel tread spacing

should be increased when working on inclines or

rough ground to reduce the possibility of tipping.

Use extreme caution when operating on steep

slopes. Keep the tractor in a low gear when going

downhill. DO NOT coast or free-wheel downhill.

OPS-R-0019

OPERATION

RX60/72/84 10/12 Operation Section 4-32

OPERATION

9.5 Crossing Ditches and Steep Inclines

When crossing ditches with steep banks or going up

sharp inclines, it is possible that the main driveline

inner profile will penetrate into the outer housing to its

maximum depth until the assembly becomes solid

(driveline is at its extreme shortest length). This type

of abusive operation can cause serious damage to

the tractor and mower drive by pushing the PTO into

the tractor and through the support bearings or

downward onto the PTO shaft, breaking it off.

Damage resulting from over-collapse of the driveline’s inner profile and its outer housing

may allow the driveline to come loose from the Tractor which could cause bodily injury to the

operator or bystanders and/or extensive damage to the Tractor or Implement. OPS-R-0020

When confronted with an incline or ditch, do not

approach from an angle which is perpendicular or

straight on as damage to or over-collapse of the

driveline may occur. OPS-R-0021_A

OPERATION

RX60/72/84 10/12 Operation Section 4-33

OPERATION

Inclines and ditches should be approached along a

line which is at an angle as shown. This type of

path will reduce the possibility of over-collapse of

the driveline and resulting damage. If the gradient

is so steep that such an approach increases the

possibility of a tractor roll-over, select an alternate

crossing path.

When operating the tractor and mower across

slopes and inclines, through ditches, and other

uneven terrain conditions, it is important to maintain

sufficient deck to ground clearance. Blade contact

with the ground may cause soil, rocks and other

debris to be thrown out from under the mower

resulting in possible injury and/or property damage.

Ground contact also produces a severe shock load

on the mower drive and to the mower blades

resulting in possible damage and premature wear.

OPS-R-0022

10. OPERATING THE TRACTOR AND IMPLEMENT

THE OPERATOR MUST COMPLETELY UNDERSTAND HOW TO OPERATE THE TRACTOR AND

IMPLEMENT AND ALL CONTROLS BEFORE ATTEMPTING TO OPERATE. The operator must read and

understand the Safety and Operation Sections of the implement and tractor operator’s manuals. These

manuals must be read and explained to any operator who cannot read. Never allow someone to operate the

implement and tractor without complete operating instructions.

Before starting any operation, the operator must become familiar with the area to be worked in and any

obstacles and hazards contained within to ensure safety to the operator, bystanders, and equipment. Special

attention should be paid to foreign debris, rough terrain, steep slopes, and passersby and animals in the area.

OPS-U- 0015

Extreme care should be taken when operating near loose objects such

as gravel, rocks, wire, and other debris. Inspect the area before

mowing. Foreign objects should be removed from the site to prevent

machine damage and/or bodily injury or even death. Any objects that

cannot be removed must be clearly marked and carefully avoided by the

operator. Stop mowing immediately if blades strike a foreign object.

Repair all damage and make certain rotor or blade carrier is balanced

before resuming mowing.

(SGM-05)

OPERATION

RX60/72/84 10/12 Operation Section 4-34

OPERATION

Many varied objects, such as wire, cable, rope, or chains, can become entangled in the

operating parts of the mower head. These items could then swing outside the housing at

greater velocities than the blades. Such a situation is extremely hazardous and could result

in serious injury or even death. Inspect the cutting area for such objects before mowing.

Remove any like object from the site. Never allow the cutting blades to contact such items.

(SGM-06)

10.1 Foreign Debris Hazards

Before mowing, inspect the area to make sure

there are no foreign objects that the mower blades

could hit or become entangled with. Remove all

foreign objects and debris. If objects are too big to

remove, mark them clearly and be sure to prevent

the mower blades from contacting them.

If you hit a solid object or foreign debris, stop the

mower and tractor at once. Immediately idle the

engine speed and disengage the PTO. Wait for all

mower rotating motion to stop, then raise the

mower and move the tractor and implement off the

object. Inspect the area and remove, or mark the

location of the debris. Inspect the condition of the

mower and make any needed repairs immediately.

Make sure the blades are not damaged and the

carrier is balanced before resuming operation.

Always wear your seat belt securely fastened and

only operate the tractor and mower with the ROPS

in the raised position. If the tractor or mower hits a

tree stump, rock, or bump, a sudden movement

could throw you off of the seat and under the

tractor and/or mower. The seat belt is your best

protection from falling off the tractor and the ROPS

provides protection from being crushed during a

tractor roll-over. OPS-R-0023

Remove Foreign Material

Raise Mower over solid objects

10.2 Bystanders/Passersby Precautions

If a bystander comes within 300 feet of the tractor while the mower is being operated, stop the tractor at once,

idle the engine and disengage the PTO. Do not engage the PTO again until all bystanders are well past the

300 foot distance. OPS-R-0024

OPERATION

RX60/72/84 10/12 Operation Section 4-35

OPERATION

Rotary Mowers are capable under adverse conditions of throwing

objects for great distances (300 ft (100 m) or more) and causing serious

injury or death. Follow safety messages carefully.

STOP MOWING IF PASSERSBY ARE WITHIN 300 Feet (100 m) UNLESS:

-Front and Rear Deflectors, Chain Guards, or Bands are installed and in good, workable

condition;

-Mower sections or Wings are running close to and parallel to the ground without exposed

Blades;

-Passersby are outside the existing thrown-object zone;

-All areas have been thoroughly inspected and all foreign material such as rocks, cans,

glass, and general debris has been removed.

NOTE: Where there are grass and weeds high enough to hide debris that could be struck

by the blades, the area should be: inspected and large debris removed, mowed at an

intermediate height, inspected, closely with any remaining debris being removed, and

mowed again at desired final height. (This will also reduce power required to mow, reduce

wear and tear on the Mower drivetrain, spread cut material better, reduce streaking, and

make the final cut more uniform).

(SRM-01)

10.3 Engaging the Power Take Off (PTO)

Before engaging the PTO, make certain that the area is clear of bystanders and passersby. The implement

must be completely lowered and the deck positioned at a safe operating height. NEVER engage the PTO with

the implement in the raised position.

Set the tractor engine speed at approximately 1,000 RPM before engaging the PTO. Shift the PTO control to

the on position, and slowly increase the engine speed until the PTO is operating at the rated speed. If you

hear unusual noises or see or feel abnormal vibrations, disengage the PTO immediately. Inspect the

implement to determine the cause of the noise or vibration and repair the abnormality. OPS-U- 0027

Do not let the Blades turn when the Mower Deck is raised for any

reason, including clearance or for turning. Raising the Mower deck

exposes the Cutting Blades which creates a potentially serious hazard

and could cause serious injury or even death from objects thrown from

the Blades.

(SRM-07)

Do not put hands or feet under mower decks. Blade Contact can result

in serious injury or even death. Stay away until all motion has stopped

and the decks are securely blocked up.

(SGM-09)

OPERATION

RX60/72/84 10/12 Operation Section 4-36

OPERATION

10.4 PTO RPM and Ground Speed

Ground speed for mowing will depend upon the height, type, and density of vegetation to be cut.

Recommended speed for efficient mower performance is between 2 and 5 mph(3-8 kph). Operate the mower

at its full rated PTO speed to maintain blade speed for a clean cut. Refer to the tractor operator’s manual or

the tractor instrument panel for the engine speed and gear to provide the required PTO and desired ground

speed. Make sure that the mower is operating at its full rated speed before entering the vegetation to be cut.

If it becomes necessary to temporarily regulate engine speed, increase or decrease the throttle gradually.

Ground speed is achieved by transmission gear selection and not by the engine operating speed. The

operator may be required to experiment with several gear range combinations to determine the best gear and

range which provides the most ideal performance from the mower and most efficient tractor operation. As the

severity of cutting conditions increase, the ground speed should be decreased by selecting a lower gear to

maintain the proper operating PTO speed. OPS-R-0025

Do not exceed the rated PTO speed for the Implement. Excessive PTO speeds can cause

Implement driveline or blade failures resulting in serious injury or death.

(SG-26)

Mow at the speed that you can safely operate and control the tractor and mower. The

correct mowing speed depends on terrain condition and grass type, density, and height of

cut. Normal ground speed range is from 2 to 5 mph(3-8 kph). Use slow mowing speeds

when operating on or near steep slopes, ditches, drop-offs, overhead obstructions, power

lines, or when debris and foreign objects are to be avoided.

(SGM-07)

10.5 Operating the Mower

Only operate the mower from the tractor operator’s seat with the seatbelt securely fastened. The tractor must

be equipped with a ROPS in the raised position or a ROPS cab.

The mower is designed to cut vegetation up to 2-1/2” in diameter. Sharp blades will produce a cleaner cut and

require less power. Travel at a speed that allows the mower sufficient time to cut through the vegetation and

maintain the PTO operating speed to prevent overloading the mower and tractor. Choose a driving pattern

that provides the maximum pass length and minimizes turning.

Under certain conditions, tractor tires may roll some grasses down preventing them from being cut at the

same height as the surrounding area. When this occurs, reduce the tractor ground speed while maintaining

the operating speed of the mower. A slower ground speed will permit grasses to at least partially rebound and

be cut. Taking a partial cut and/or reversing the direction of travel may also help produce a cleaner cut.

Avoid mowing in the reverse direction when possible. In situations where the mower must be backed to

access areas to be cut, make sure there are no persons or other foreign debris behind the mower before

mowing in reverse. When mowing in reverse, operate the tractor and mower at a reduced ground speed to

ensure tractor and mower control is maintained. OPS-R-0026_F

OPERATION

RX60/72/84 10/12 Operation Section 4-37

OPERATION

10.6 Cutting Material

When cutting trees and brush approach material to be

cut with the head perpendicular to the material. The

cutting edge of the blades should be the only

elements in contact with material. The blade bar

should not contact the material. Material should be

fed through the head rather than the head being

lowered on top of material. If the blade bar edges are

gouged or rounded from wear, the mower head is

being used incorrectly in an abusive manner. The

blade bar is not intended to cut material or to be a

wear item like the blades. Do Not allow the blades or

blade bar to contact the ground, rocks or other solid

objects. Contact with the ground can result in rocks

and solid objects being thrown out from under the

mower head which can cause serious injuries to the

operator or bystanders. This type of operation can

lead to bent or broken blade bars, broken blade bolts

and broken blade bar assembly bolts which can be

dangerous to the operator or bystanders.

Do not mow with two machines in the same area except with Cab tractors with the windows

closed.

(SGM-11)

Mow only in conditions where you have clear visibility in daylight or with adequate artificial

lighting. Never mow in darkness or foggy conditions where you cannot clearly see at least

300 feet (90 m) in front and to the sides of the tractor and mower. Make sure that you can

clearly see and identify passersby, steep slopes, ditches, drop-offs, overhead obstructions,

power lines, debris and foreign objects. If you are unable to clearly see these type of items

discontinue mowing.

(SGM-1)

Avoid mowing in reverse direction when possible. Check to make sure there are no

persons behind the mower and use extreme care when maneuvering in reverse. Mow only

at a slow ground speed where you can safely operate and control the tractor and mower.

Never mow an area that you have not inspected and removed debris or foreign material.

(SGM-08)

OPERATION

RX60/72/84 10/12 Operation Section 4-38

OPERATION

Follow these guidelines to reduce the risk of equipment and grass fires

while operating, servicing, and repairing the Mower and Tractor:

-Equip the Tractor with a fire extinguisher in an accesible location.

-Do Not operate the Mower on a Tractor with an underframe exhaust.

-Do Not smoke or have an open flame near the Mower and Tractor.

-Do Not drive into burning debris or freshly burnt areas.

-Ensure slip clutches are properly adjusted to prevent excessive slippage and plate heating.

-Never allow clippings or debris to collect near drivelines, slip clutches, and gearboxes.

Periodically shut down the Tractor and Mower and clean clippings and collected debris from

the mower deck.

(SGM-12)

When you get to the end of a pass, slightly raise the

mower (2-4”) before turning. Never raise the

mower entirely while the blades are turning. If the

mower must be raised higher than 12” from ground

level, disengage the tractor PTO and wait for all

mower rotation to come to a complete stop before

proceeding to raise the mower. OPS-R-0027_B

Do not let the Blades turn when the Mower Deck is raised for any

reason, including clearance or for turning. Raising the Mower deck

exposes the Cutting Blades which creates a potentially serious hazard

and could cause serious injury or even death from objects thrown from

the Blades.

(SRM-07)

OPERATION

RX60/72/84 10/12 Operation Section 4-39

OPERATION

Large, dense, or wet vegetation may need to be

mowed in two or more passes to achieve a uniform

cut. In such conditions, raise the cutting height to

12” or more on the first pass

. OPS-R-0043

Then lower the mower to the desired height and

mow the vegetation a second time. If possible,

select a mowing pattern that is at a 90 degree angle

to the first pass to reduce streaking for a more

uniform cut. OPS-R-0044

Stay alert and watch for trees, low hanging limbs,

power lines, and other overhead obstacles and solid

ground objects while you are operating. Use care

to avoid hitting these items

. OPS-R-0028_A

OPERATION

RX60/72/84 10/12 Operation Section 4-40

OPERATION

10.7 Right of Way (Highway) Mowing

Do not mow, or drive the tractor into material that is burning, or areas that recently burnt and may contain hot

spots. Burning material, sparks, and coals could be thrown from the mower to areas of vegetation that might

ignite. Tire damage can occur when driving over hot material. Oil and grease on the tractor and mower could

ignite resulting in equipment destruction. Carry a fire extinguisher on the tractor at all times to extinguish

possible fires encountered

• USE DOUBLE CHAIN GUARDS for highway, right-of-way, parks, greenbelt mowing, or all other mowing

where human dwellings, vehicles, or livestock could be within 300 feet of the mower.

• No shielding is 100% effective in preventing thrown objects. To Reduce Possibility of Injury:

1. MAINTAIN MOWER SHIELDING in good operational condition,

2. DAILY INSPECT the condition of the Thrown Object Guards, mower Side Skirts, and skid shoes:

Replace or repair worn or damaged guards.

3. DAILY INSPECT the condition of the Blades and Blade Bolts. Replace any cracked, worn, bent or

damage blades. Always replace blade bolts and nuts when replacing blades. Make sure the blade

bolts are properly tightened.

4. RAISE CUTTING HEIGHT to 6 INCHES minimum.

5. INSPECT AREA thoroughly before mowing to REMOVE potential THROWN OBJECT HAZARDS.

6. NEVER ALLOW BLADES to CONTACT SOLID OBJECTS like wire, rocks, posts, curbs, guardrails,

or ground while mowing.

ROTARY MOWERS CAN THROW OBJECTS 300 FEET OR MORE UNDER ADVERSE

CONDITIONS.

TO AVOID SERIOUS INJURY OR DEATH TO OPERATOR OR BYSTANDERS FROM THROWN

OBJECTS:

INSPECT AREA FOR POTENTIAL THROWN OBJECTS BEFORE MOWING:

• REMOVE debris, rocks, wire, cable, metal objects and other foreign material from area.

Wire, cable, rope, chains and metal objects can be thrown or swung outside deck with great velocity:

1. MARK objects that cannot be removed.

2. AVOID these objects when mowing.

STOP MOWING IF PASSERSBY IS WITHIN 300 FEET UNLESS:

• All THROWN OBJECT SHIELDING including Front and Rear Deflectors, Chain Guards, Steel Guards,

Bands, Side Skirts and Skid Shoes are in place and in good condition when mowing.

• Mower sections or wings are adjusted to be close and parallel to ground without exposing blades.

• MOWING AREA has been inspected and foreign materials and debris have been removed.

• PASSERSBY are inside enclosed vehicle. OPS-U-0040

OPERATION

RX60/72/84 10/12 Operation Section 4-41

OPERATION

Never stand or allow another person to stand between a running Tractor and the Mower

when disconnecting the Implement from the Tractor 3-point hitch.

10.8 Shutting Down the Implement

To shut down attached mower head, first bring the

tractor to a complete stop. Decrease engine RPM

to idle then disengage cutterhead. The mower head

will come to a complete stop within a suitable

amount of time. Do not engage or disengage the

cutterheads at a high RPM unless there is an

emergency situation.

Park the tractor on a level surface, place the

transmission in park or neutral and apply the

parking brake, lower the attached implement to the

ground, shut down the engine, remove the key, and

wait for all motion to come to a complete stop

before exiting the tractor. OPS-U- 0016

11. DISCONNECTING THE MOWER FROM THE TRACTOR

Before disconnecting the mower, the PTO must be

disengaged and blade rotation at a complete stop.

Move the mower to a level storage location and

lower it to the ground. If the mower is not resting

securely on the ground, block the mower up

securely before attempting to disconnect it from

the tractor.

Use extreme care to keep feet and hands from

under the mower and clear of any pinch points

caused by the tractor hitch arms and mower pins.

OPS-R-0030_A

OPERATION

RX60/72/84 10/12 Operation Section 4-42

OPERATION

Always shut the Tractor completely down, place the transmission in park, and set the

parking brake before you or anyone else attempts to connect or disconnect the Implement

and Tractor hitches.

(S3PT-15)

To disconnect the mower, first extend the tractor 3-

point hitch top link to remove tension on the top link

hitch pin. When the pin is loose and easy to rotate,

remove the pin from the mower. Next remove both

lower hitch pins.

After disconnecting the 3 lift points, remove the

mower driveline from the tractor PTO shaft. Lay

the driveline down carefully on support flat to avoid

damaging the driveline or its shield. Do not let the

driveline fall into mud or dirt, which can

contaminate the bearing and shorten the life of the

driveline. OPS-R-0031_B

OPERATION

RX60/72/84 10/12 Operation Section 4-43

OPERATION

12. MOWER STORAGE

Properly preparing and storing the mower at the end of the season is critical to maintaining its appearance

and to help ensure years of dependable service. The following are suggested storage procedures:

• Thoroughly clean all debris off the mower to

prevent damage from rotting grass and

standing water.

• Lubricate all mower grease points and fill

gearbox oil levels as detailed in the

maintenance section.

• Tighten all bolts and pins to the recommended

torque.

• Check the mower for worn and damaged

parts. Perform repairs and make

replacements immediately so that the mower

will be ready for use at the start of the next

season.

• Store the mower in a clean, dry place with the

mower housing resting securely on blocks or

at ground level.

• Keep the driveline yoke from sitting in water, dirt and other contaminants.

• Use spray touch-up enamel where necessary to prevent rust and maintain the appearance of the mower.

It is critical that driveline clutches slip when an obstacle or heavy load is encountered to avoid mower and/or

tractor damage. If the mower sits outside for an extended period of time or is exposed to rain and/or humid

air, the clutch lining plates must be inspected to ensure they are not frozen together from rust or corrosion. If

the mower has been exposed to such conditions, at the start of each mowing season, and any time it is

suspected that the slip clutch plates may be frozen together, readjust the slip clutch as detailed in Seasonal

Clutch Maintenance of the maintenance section in this manual. OPS-R-0032_A

Never allow children or other persons to ride on the Tractor or Implement.

Falling off can result in serious injury or death.

(SG-10)

13. TRANSPORTING THE TRACTOR AND IMPLEMENT

Inherent hazards of operating the tractor and implement and the possibility of accidents are not left behind

when you finish working in an area. Therefore, the operator must employ good judgement and safe operation

practices when transporting the tractor and implement between locations. By using good judgement and

following safe transport procedures, the possibility of accidents while moving between locations can be

substantially minimized. OPS-U- 0017

OPERATION

RX60/72/84 10/12 Operation Section 4-44

OPERATION

Before transporting the tractor and mower, idle the

tractor engine, disengage the PTO and wait for all

mower moving parts to come to a complete stop.

Once all mower parts are completely stopped, raise

the mower to transport height. NOTE: When

raising the mower, maintain 1” clearance between

the driveline and mower deck. If additional mower

deck height is needed for safe transport, disconnect

the driveline from the tractor and secure its end to

the mower deck. The mower can then be raised to

the maximum lift height. OPS-R-0033_A

If the tractor’s hydraulic pump is not independent of

the tractor PTO, or if the tractor PTO has to be run

to have hydraulic power, disconnect the mower

driveline from the tractor PTO output shaft. Secure

the driveline to the mower deck to prevent driveline

damage or loss during transport. OPS-R-0034

13.1 Transporting on Public Roadways

Extreme caution should be used when transporting the tractor and implement on public roadways. The tractor

must be equipped with all required safety warning features including a SMV emblem and flashing warning

lights to alert drivers of the tractor’s presence. Remember that roadways are primarily designed for

automotive drivers and most drivers will not be looking out for you, therefore, you must look out for them.

Check your side view mirrors frequently and remember that vehicles will approach quickly because of the

tractor’s slower speed. Be extremely cautious when the piece of equipment that you are towing is wider than

the tractor tire width and/or extends beyond your lane of the road.

Make sure that a proper size safety tow chain is secured between the tractor and implement before entering a

public road. OPS-U- 0019

Make certain that the “Slow Moving Vehicle” (SMV) sign is installed in

such a way as to be clearly visible and legible. When transporting the

Equipment use the Tractor flashing warning lights and follow all local

traffic regulations.

(SG-6)

OPERATION

RX60/72/84 10/12 Operation Section 4-45

OPERATION

The SMV (Slow-Moving Vehicle) emblem is

universal symbol used to alert drivers of the

presence of equipment traveling on roadways at a

slow speed. SMV signs are a triangular bright

orange with reflective red trim for both easy day

and night visibility. Make sure the SMV sign is

clean and visible from the rear of the unit before

transporting the tractor and implement on a public

roadway. Replace the SMV emblem if faded,

damaged, or no longer reflective. OPS-U- 0020

Make sure that all tractor flashing warning lights,

headlights, and brake/tail lights are functioning

properly before proceeding onto public roads. While

newer model tractors have plenty of lighting to

provide warning signals and operating lighting, most

older models are only equipped with operating lights.

Consult an authorized tractor dealer for lighting kits

and modifications available to upgrade the lighting on

older tractor models. OPS-U- 0021

When operating on public roads, have

consideration for other road users. Pull to the side

of the road occasionally to allow all following traffic

to pass. Do not exceed the legal speed limit set in

your country for agricultural tractors. Always stay

alert when transporting the tractor and implement

on public roads. Use caution and reduce speed if

other vehicles or pedestrians are in the area. OPS-

U- 0022_A

OPERATION

RX60/72/84 10/12 Operation Section 4-46

OPERATION

13.2 Hauling the Tractor and Implement

Before transporting a loaded tractor and implement, measure the height and width dimensions and gross

weight of the complete loaded unit. Ensure that the load will be in compliance with the legal limits set for the

areas that will be traveled through

Use adequately sized and rated trailers and equipment to transport the tractor and implement. Consult an

authorized dealer to determine the proper equipment required. Using adequately sized chains, heavy duty

straps, cables and/or binders, securely tie down both the front and rear of the tractor utilizing the proper tie

down locations as specified by the tractor manufacturer.

Arrange the chains so that when tightened, the chains are pulling downward and against themselves. Carefully

tighten the securing chains or other fasteners using boomers or binders to apply maximum tension. Use

extreme care when attaching and removing the securing devices as the extreme tension involved when

released has the potential to inflict serious injury.

While hauling the tractor and implement, make occasional stops to check that the tractor and implement have

not moved or shifted and that the securing chains have maintained tension. If during transport a hard braking,

sharp turning, or swerving action was performed, stop at the next safe location to inspect the security of the

load.

Reduce speed before turning or applying the brakes.

Ensure that both brake pedals are locked together

when operating on public roads. OPS-U- 0023

OPERATION

RX60/72/84 10/12 Operation Section 4-47

OPERATION

14. TROUBLE SHOOTING GUIDE

Problem Possible Cause Remedy

Uneven Cut Excessive ground speed. Reduce ground speed.

Blades worn, dull, or bent. Replace blades.

(Refer to “Maintenance” section).

Mower not level side to side. Adjust. (Refer to “Assembly” section)

Improper height adjustment. Adjust Mower height.

(Refer to “Assembly” section)

Low tractor tire pressure on Adjust tire pressure.

one side (Refer to your tractor operator's

manual)

Turning too fast. Reduce ground speed when turning.

Tractor tires push grass down. Adjust your tractor wheel spacing.

(Refer to “Operation” section)

Damaged Mower pan. Repair or replace as necessary.

Uncut Material Excessive ground speed Reduce ground speed.

RPM too low Use full PTO speed.

(Refer to your tractor operator's

manual)

Improper blade for direction of cut. Install blades so rotation is correct.

Poor Shredding Excessive ground speed. Raise the front of Mower relative to the

rear to hold and circulate material

longer. (Refer to the “Operation Section

Setting the Mower-Setting Deck

Height”) Reduce ground speed.

Cutting too high. Lower cutting height. (Refer to the

“Operation Section-Setting the Mower-

Setting Deck Pitch”)

Windrowing Material heavy and lush. Raise the front of Mower relative to the

or Uneven rear. (Refer to the “Operation Section-

Your Material Distribution Setting the Mower- Setting Deck

Height”)

Excessive ground speed Reduce ground speed.

Conditions too wet. Wait for conditions to dry. Reduce

ground speed.

OPERATION

RX60/72/84 10/12 Operation Section 4-48

OPERATION

Blade Bolts Working Loose Bolts not tightened. Tighten Bolts to 300 ft./lbs.

Bolt hole elongated or oversized. Replace Blade Carrier.

Locknut worn out. Replace Locknut.

Gearbox Noisy Low Lubricant. Check lubricant level.

Rough gears. Run in or change Gears.

Worn Bearing. Replace Bearing.

Gearbox Leaking Damaged Oil Seal. Replace Seal.

Bent Shaft. Replace Oil Seal and Shaft.

Oil Seal Race rough. Replace Shaft or repair Race.

Oil Seal installed wrong. Replace Seal.

Oil Seal not sealing in the housing. Replace Seal or use a sealant on O.D.

of Seal.

Oil level too high. Drain oil to proper level.

Gasket damaged. Replace Gasket.

Bolts loose. Tighten Bolts.

Sand hole in casting. Replace castings or gearbox.

Streaking Conditions Conditions too wet for cutting. Allow grass to dry before cutting. Slow

Blades unable to cut that part of ground speed of tractor but keep

grass pressed down by path of engine running at full PTO wpm.

tractor tires. Lowering the cutting height may help.

Dull blades. Sharpen or replace blades.

Height of cutter lower at rear or See Cutting Height Instructions.

front.

Gearbox Overheating Low on lubricant. Fill to level plug.

Improper type lubricant. Replace with proper lubricant.

Excessive trash build-up around Remove trash.

gearbox.

Bearing or gears set up improperly. Consult your Dealer.

Shear Pin Shears Tractor PTO not being run at Run at 540 RPM.

Excessively 540 RPM.

Heavy Material. Reduce ground speed. Raise cutting

height.

Not using proper pin. Replace only with recommended shear

pin.

PTO engaged at high engine RPM Idle engine to engage PTO

Cutting in rocky conditions Increase cutting height.

Blade carrier RPM too high. Check gearbox ratios.

Blades not properly heat treated. Consult your Dealer.

Maintenance Section 5-1

MAINTENANCE SECTION

MAINTENANCE

RX60/72/84 10/12 Maintenance Section 5-2

MAINTENANCE

HAZARDS WITH MAINTENANCE OF IMPLEMENT

AVOID SERIOUS INJURY OR DEATH FROM COMPONENT FAILURE BY KEEPING IMPLEMENT IN

GOOD OPERATING CONDITION IN PERFORMING PROPER SERVICE, REPAIRS AND

MAINTENANCE.

BEFORE PERFORMING SERVICE, REPAIRS AND MAINTENANCE ON THE IMPLEMENT:

SECURE EQUIPMENT FOR SERVICE

BLOCK OUT POTENTIAL ENERGY HAZARDS; Rotating Parts, Raised Components, Hydraulic Pressure.

• STOP ENGINE AND PTO, engage parking brake, lower implement, allow all moving parts to stop and remove key before

dismounting from tractor.

•

PLACE implement on ground or securely block up raised equipment. Use large blocks on soft or wet soil.

• SECURELY LATCH and LOCK raised implement wings

• BLOCK UP IMPLEMENT TONGUE with large blocks and tongue jack. DO NOT crawl or work under implement supported only by

tongue jack.

•

PUSH and PULL Remote Hydraulic Cylinder lever to relieve hydraulic pressure.

• DISCONNECT IMPLEMENT Hydraulic HOSES from tractor

•

DISCONNECT IMPLEMENT driveline from tractor PTO SHAFT.

WEAR SAFETY GLASSES, PROTECTIVE GLOVES and follow SAFETY PROCEDURES when performing service, repairs

and maintenance on the implement:

• Always WEAR protective GLOVES when handling blades, knives, cutting edges or worn component with sharp edges.

• Always

WEAR GLOVES and SAFETY GLASSES when servicing hot components

•

AVOID CONTACT with hot hydraulic oil tanks, pumps, motors, valves and hose connection surfaces.

•

SECURELY support or BLOCK UP raised implement, framework and lifted components before working underneath equipment.

•

STOP any implement movements and SHUT-OFF TRACTOR engine before doing any work procedures.

•

USE ladder or raised stands to reach high equipment areas inaccessible from ground.

•

ENSURE good footing by standing on solid flat surfaces when getting on implement to perform work.

•

FOLLOW manufacturer's instructions in handling oils, solvents, cleansers, and other chemical agents.

•

DO NOT change any factory-set hydraulic calibrations to avoid component or equipment failures.

•

DO NOT modify or alter implement, functions or components.

•

DO NOT WELD or repair rotating mower components. These may cause vibrations and component failures being thrown from

mower.

PERFORM SERVICE, REPAIRS, LUBRICATION AND MAINTENANCE OUTLINED IN IMPLEMENT MAINTENANCE

SECTION:

• INSPECT for loose fasteners, worn or broken parts, leaky or loose fittings, missing or broken cotter keys and washers on pins, and

all moving parts for wear.

•

REPLACE any worn or broken parts with authorized service parts.

•

LUBRICATE unit as specified by lubrication schedule

•

NEVER lubricate, adjust or remove material while it is running or in motion.

•

TORQUE all bolts and nuts as specified.

BLADE INSPECTION:

• REPLACE bent, damage, cracked or broken blades immediately with new blades.

•

AVOID blade failures and thrown broken blades. DO NOT straighten, weld, or weld hard-facing blades.

SAFETY SHIELDS, GUARDS AND SAFETY DEVICES INSPECTION:

• KEEP all Deflectors, Chain Guards, Steel Guards, Gearbox Shields, and PTO integral shields, Bands, Side Skirts and Skid Shoes

in place and in good condition.

•

REPLACE any missing, broken or worn safety shields, guards and safety devices.

• Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the state of California

to cause cancer, birth defects or other reproductive harm.

• Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the state of California to

cause cancer, birth defects or other reproductive harm.

PN HM01

MAINTENANCE

RX60/72/84 10/12 Maintenance Section 5-3

MAINTENANCE

Before operating your Rotary Cutter, make sure it is properly lubricated and thoroughly inspected. Only a mini-

mum of time and effort is required to regularly lubricate and maintain this machine to provide long life and trou-

ble free operation.

Always disengage the PTO before raising the Rotary Cutter for transporting or making

adjustments.

Lubrication

Do not let excess grease collect on or around parts, particularly when operating in sandy areas. The

illustrations below shows lubrication points (Figure Mnt-R-0080). The chart gives the frequency of lubrication

in hours, based on normal operating conditions. Severe or unusual conditions may require more frequent

lubrication.

Use an multi-purpose gear oil (PN 00786250) for all locations shown. Be sure to clean the fitting thoroughly

before using grease gun. Daily lubrication of the driveline slip joint is necessary. Failure to maintain proper

lubrication will result in damage to U-joints, gearbox, and/or driveshaft.

PARTS INFORMATION

Alamo Industrial mowers use balanced and matched system components for blade carriers, blades,

cuttershafts, knives, knife hangers, rollers, drivetrain components, and bearings. These parts are made and

tested to Alamo Industrial specifications. Non-genuine "will fit" parts do not consistently meet these

specifications. The use of “will fit” parts may reduce mower performance, void mower warranties, and present

a safety hazard. Use genuine Alamo Industrial mower parts for economy and safety.

(SPAM-1)

SEE YOUR ALAMO DEALER

MAINTENANCE

RX60/72/84 10/12 Maintenance Section 5-4

MAINTENANCE

RX60/72/84 10/12 Maintenance Section 5-5

MAINTENANCE

RX60/72/84 10/12 Maintenance Section 5-6

MAINTENANCE

GEARBOX (Model RX60 & RX84)

The gearbox should be full (3 quarts) and not

require additional lubricant unless the box is

cracked or a seal is leaking. It is recommended that

the oil level dipstick (Figure MntP-R-0056) be

removed to check oil level after every 8 hours of

operation. If required, oil should be added until it

comes to proper level.

Recommended lubricant is multi-purpose gear oil,

Alamo Industrial P/N 00786250.

NOTE: Make sure mower is level when checking oil

in the gearbox.

Gearbox capacity is 3 quarts.

NOTE: Overfilling of Gearbox will cause pressure

to build up and cause Grease Seals to leak.

GEARBOX (Model RX72)

Follow the same instructions as listed above for (Figure Op-1225)

MAINTENANCE

RX60/72/84 10/12 Maintenance Section 5-7

MAINTENANCE

TAIL WHEEL ASSEMBLY

Tail Wheel Bearings are packed at the factory with heavy-duty bearing grease. Grease Fittings are provided in

the Wheel Hub and Tail Wheel Beam. Grease after 10 hours of use. Figure Mnt-0004.

DRIVELINE LUBRICATION

Grease Fittings are located on the Cross Assembly of each U-Joint and on the telescoping tubes. Grease the

U-Joint after each 8 hours of use. Figure Mnt-R-0283. Do not force grease through the Needle Cup

Assemblies. Grease the telescoping tubes after every 8 hours use. Some PTO-to-Hitch connections may

necessitate cutting a hole in the shields to be able to align the Grease Fitting holes for lubrication. Lubricate the

shield bearings every 16 hours.

The Driveline Integral Shields should not become dented or otherwise damaged. The Integral Shield Assembly

has a Nylon Bearing at each end and should turn freely. This nylon bearing should require lubrication weekly.

To remove the Integral Shields for replacement or repair, remove the screws on the Shield. Slip the Shield

Cone Assembly off inner section of the Driveline. Install the new or repaired Shield on the Driveline. Place the

split Nylon Bearing over the Driveline Housing of Shaft against the Yoke and in the Bearing groove. Install

shield over the Housing so the Nylon Bearing fits into the Shield Bearing Retainer. Align holes on the Shield

and replace the screws in the Shield.

Make certain that the Driveline Integral Shields are free to telescope and rotate around the

Driveline without binding.

MAINTENANCE

RX60/72/84 10/12 Maintenance Section 5-8

MAINTENANCE

LIFT TYPE DRIVELINE & PULL JACKSHAFT SHIELDS

To remove the main inner driveline shield, Remove the locking screws. Align the bearing tabs with the cone

pockets. FIGURE Mnt-0026. Remove the half-guard and remove the bearing ring. FIGURE Mnt-R-0012.

Inspect the driveline shield for worn areas or cracks. If the shield has any dents or cracks, replace the Shield.

While the Shields are off, examine the Driveline for signs of abnormal wear, bent or twisted shafts, or cracks in

the shafts or tubes. Check to see that the Drivelines telescope easily. If the Drivelines do not telescope

properly or show signs of abnormal wear, the shaft should be repaired or replaced.

To assemble the main inner driveline shield, grease the yoke groove and inner profile tube. Attach the bearing

ring in groove with recesses facing profile tube. FIGURE Mnt-0027. Slide on the half shield. Turn the cone until

it engages correctly. Install locking screws. FIGURE Mnt-0028.

MAINTENANCE

RX60/72/84 10/12 Maintenance Section 5-9

MAINTENANCE

CV TYPE DRIVELINE

MAIN CV DRIVELINE SAFETY SHIELD

1. To remove the outer CV cone, remove the locking screws from shield cone. Remove cone over yoke.

Remove bearing ring and remove the locking screws from inner shield cone. Turn inner cone to assembly

position and remove half shield. Remove bearing ring. MNT-R-0038.

MAINTENANCE

RX60/72/84 10/12 Maintenance Section 5-10

MAINTENANCE

2. To assemble outer CV driveline, grease yoke groove and inner profile tube. Attach bearing ring on groove

with recesses facing profile tube. Slide on half shield with cone. Turn cone until it engages correctly.

Tighten locking screws. Grease bearing groove in double yoke. Insert bearing ring. Slide guard cone for

double yoke over cam from the connecting end. Make sure holes for screws are visible. Tighten locking

screws. MNT-R-0039.

IMPORTANT: Scan this QR Code with your smart phone to link to the ADMA

Driveline Safety Manual for more information on the safe use of a driveline during

normal operation and maintenance. Or type in your internet browser the following

web address: www.algqr.com/dme

Ops-0009-MISC

MAINTENANCE

RX60/72/84 10/12 Maintenance Section 5-11

MAINTENANCE

BLADE SERVICING

Inspect blades before each use to determine that they are properly installed and in good condition. Replace

any blade that is bent, excessively nicked, worn, or has any other damage. Small nicks can be ground out

when sharpening.

Use only original equipment blades on this cutter. They are made of special heat-treated

alloy steel. Substitute blades may not meet specifications and may fail in a hazardous

manner that could cause injury.

Replace bent or broken blade with new blades. NEVER ATTEMPT TO STRAIGHTEN OR

WELD ON BLADES SINCE THIS WILL LIKELY CRACK OR OTHERWISE DAMAGE THE

BLADE WITH SUBSEQUENT FAILURE AND POSSIBLE SERIOUS INJURY FROM

THROWN BLADES.

(SGM-10)

• Manually wiggle the blade carriers to check for any looseness.

• Retighten any loose parts.

• Recheck torque every 50 hours.

Operating with loose blade hardware will damage the blade holder and blades. Whenever

the blades have been removed or replaced, the hardware must be retightened after the first

eight hours of operation. On new units check blade hardware and the blade nut torque after

first 8 hours.

Operating with loose blade holder will damage the blade holder and output shaft, two initial

tightenings are required. Retighten after one hour and again after the day of operation. In

severe cutting conditions or commercial use, a daily inspection is required.

To help prevent structural damage caused by loose hardware, tighten gear case hardware

as specified. Check torque after first 8 hours of use and every 50 hours thereafter.

NOTE: Correct Blade Rotation is counter-clockwise viewed from the top.

Inspect Blades daily for normal wear. If Blades have a notch worn into the leading worn into

the leading edge at the lower bend more than 1/2” DEEP (due to running in gravel and/or

the ground), REPLACE BOTH BLADES ON THAT CARRIER IMMEDIATELY. Failure to

replace such abnormally worn blades may lead to catastrophic failure of the blade and

ejection of the broken part with tremendous force which may cause bodily injury or death.

NOTE: Replace Blades in pairs after no more than 1/2” notch wear.

MAINTENANCE

RX60/72/84 10/12 Maintenance Section 5-12

MAINTENANCE

BLADE SHARPENING

When sharpening blades, grind each blade the same amount to maintain balance. Follow

original sharpening pattern as shown in Figure Mnt-R-0008. Always sharpen blades by

grinding. Always sharpen both blades at same time to maintain balance. The difference in

blade weights should not exceed 1 ounce. Unbalanced blades will cause excessive

vibration which can damage gear box bearings. Vibration may also cause structural cracks

in cutter housing. DO NOT heat and pound out edge. Do not sharpen blade to a razor edge,

but leave a 1/16” blunt edge. Do not sharpen back side of blade.

Avoid personal injury. Always block the cutter up to prevent if from falling when the blades

and/ or carrier are being serviced.

BLADE CARRIER REMOVAL

Remove cotter pin and loosen slotted nut on gearbox shaft. Loosen but do not remove the nut until the blade

carrier is loosened. Use a suitable 2 jaw gear puller to pull carrier off tapered gearbox shaft. If gear puller is not

available use long bar inserted through blade bolt access hole with end against rotor bar. Strike opposite end of

bar with sledge hammer. Rotate blade carrier 180 degrees and repeat process until carrier breaks loose.

BLADE CARRIER INSPECTION

Blade bolt fit into carrier bushings should be checked every time blades are changed. The blade bolt should fit

into carrier bushings as a snug slip fit. If the blade bolt fit appears to be loose or sloppy, measure the square

hole in bushing. If the bottom of the square hole is 1/16” or greater than the square shoulder of the new blade

bolt the bushings should be replaced. Bushings can be removed by cutting bushing head where it is welded to

carrier bar. Once head is removed bushing can be pressed out of bar. Clean and grind top of blade bar so new

bushing can be installed and welded. Bushing should be pressed into bar as far as possible. Use low hydrogen

rod to weld bushing in place.

MAINTENANCE

RX60/72/84 10/12 Maintenance Section 5-13

MAINTENANCE

Failure to replace a worn blade carrier bushing as described above may lead to catastrophic

failure of the blade, blade bolt, and/or blade bolt nut resulting in the ejection of the broken

parts out from under the mower at tremendous speed and force which could result in serious

bodily injury or death.

BLADE CARRIER INSTALLATION

Clean the splines on both the blade carrier and output shaft. Position carrier on the gearbox output shaft and

install special washer nut.

Tighten nut holding blade carrier to minimum 450 ft. pounds, strike the carrier near the hub several times with a

heavy hammer to seat the hub. Use a suitable spacer over the nut to prevent damage to the nut and threads.

Retighten the nut to 450 ft. pounds. Install cotter pin and spread.

Always recheck gearbox output shaft slotted blade carrier retaining nut torque after a few

hours operation.

Avoid personal injury. Do not work under cutter without support blocks to keep frame from

falling.

Operating the mower with a loose blade pan or holder can damage the taper connection on

the gearbox output shaft. To ensure proper seating between the blade holder and output

shaft, check and tighten the retaining nut after the first day of operation. Recheck the blade

carrier attachment each morning before operating. Grasp the carrier firmly with both hands

and try to push and pull the carrier with one hand while pulling and pushing with the other

hand to try to rock or oscillate the blade carrier. If the carrier is loose, retighten the retaining

nut before operating the mower.

MAINTENANCE

RX60/72/84 10/12 Maintenance Section 5-14

MAINTENANCE

BLADE REMOVAL

Remove locknut from blade bolt through inspection hole in deck of mower near the gearbox to remove blades

for sharpening or replacement. See Figure MntP-R-0057. Always replace nut when replacing blade bolt.

When installing blades be sure and check blade bolt pivot diameter for wear. Replace bolt if worn more than 1/

4 inch at any point. Tighten lock nut to 300 ft. lbs.

SLIP CLUTCH

If a slip clutch is incorporated in the PTO driveline, it is designed to slip, absorb the shock load, and protect the

driveline. This clutch has single disc spring with 6 adjusting nuts.

After the first hour of operation, the slip clutch should be checked for overheating. After this first check, the slip

clutch should be checked weekly or anytime there is overheating. To adjust the disc clutch, tighten the 6 bolts

until Belleville Spring is flat and then loosen each of them 2 turns.

The slip clutch should be checked periodically and adjusted to compensate for wear. The lining plates are 1/8”

thick when new. Replace after 1/32” wear. If the mower has been idle for an extended period of time, or in wet

weather, before operating check to be sure the friction lining plates are not rusted/corroded together. Should

this occur refer to the procedure described in the “Seasonal Clutch Maintenance” section on the next page.

There are two friction lining plates in the slip clutch. These should be checked weekly for oil or grease, wear,

and moisture which could cause corrosion on the drive plates.

MAINTENANCE

RX60/72/84 10/12 Maintenance Section 5-15

MAINTENANCE

SEASONAL CLUTCH MAINTENANCE

It is important that the clutches slip when an obstacle or load heavier than the clutch setting is encountered.

Therefore, if the machine sits outside longer than 30 days and is exposed to rain and/or humid air it is

important to make sure that the clutch lining plates are not rusted/corroded together. Before using the cutter

use the following procedure to make sure the clutch will slip and give the overload protection required.

1. Loosen nuts (Figure Mnt-R-0090) on springs until the springs are free, yet remain secure on bolts.

2. Attach cutter to tractor and start the tractor. Set the engine speed at 1200 RPM.

3. Mark outer plates as shown in Figure Mnt-R-0090.

4. Engage the PTO (approximately one second) and then quickly disengage it. The friction lining plates

should break loose (check the mark).

5. Turn tractor off. Tighten the nuts on the disc spring clutch until Belleville spring is flat, then loosen each nut

2 turns

All Safety Shields, Guards and Safety devices including (but not

limited to) - the Deflectors, Chain Guards, Steel Guards, Gearbox

Shields, PTO integral shields, and Retractable Door Shields should

be used and maintained in good working condition. All safety

devices should be inspected carefully at least daily for missing or

broken components. Missing, broken, or worn items must be

replaced at once to reduce the possibility of injury or death from

thrown objects, entanglement, or blade contact.

(SGM-3)

MAINTENANCE

RX60/72/84 10/12 Maintenance Section 5-16

MAINTENANCE

STORAGE

Your rotary cutter represents an investment from which you should get the greatest possible benefit. Therefore,

when the season is over, the cutter should be thoroughly checked and prepared for storage so that a minimum

amount of work will be required to put it back into operation for the next season. The following are suggested

storage procedures:

1. Thoroughly clean the cutter.

2. Lubricate the cutter as covered in Maintenance Section.

3. Tighten all bolts and pins to the recommended torque.

4. Check the cutter for worn or damaged parts. Make replacements immediately.

5. Place driveline in storage position resting on bracket.

6. Store the cutter in a clean, dry place with the cutter housing resting on blocks.

7. Use spray touch-up enamel where necessary to prevent rust and maintain the appearance of the cutter.

PROPER TORQUE FOR FASTENERS

The chart lists the correct tightening torque for fasteners. When bolts are to be tightened or replaced, refer to

this chart to determine the grade of bolts and the proper torque except when specific torque values are

assigned in manual text.

RECOMMENDED TORQUE IN FOOT POUNDS UNLESS OTHERWISE STATED IN THE MANUAL*

NOTE: These values apply to fasteners as received from supplier, dry or when lubricated with normal engine

oil. They do not apply if special graphited or molydisulphide greases or other extreme pressure lubricants are

used. This applies to both UNF fine and UNC coarse threads.

MAINTENANCE

RX60/72/84 10/12 Maintenance Section 5-17

MAINTENANCE

RX60/72/84 10/12 Maintenance Section 5-18

MAINTENANCE

GEARBOX SERVICING (Models RX60 & RX84)

TOOLS NEEDED FOR DISASSEMBLY AND ASSEMBLY OF GEARBOX

1. Slide Hammer Puller

2. Locktite #5900

3. Punch - Long Drift

4. Needle Nose Pliers

5. Screw Driver

6. External Snap Ring Pliers

7. Socket Wrench

8. 9/16 Socket

9. Ball Pin Hammer

10. Pry Bar

Be certain to clamp or securely support the gearbox and sub-assemblies to prevent injuries

to hands and feet due to inadvertent dropping or falling over.

Always wear safety glasses and gloves to prevent eye and hand injury when chiseling or

hammering on metal components. Hardened metal will chip unexpectedly.

An assembled gearbox is quite heavy. Use a hoist or get help to handle them safely. Lift

carefully and properly using your legs to lift - not your back.

NOTICE: Refer to operator’s manual for instructions for proper re-assembly onto the mower deck. Tighten

correctly.

MAINTENANCE

RX60/72/84 10/12 Maintenance Section 5-19

MAINTENANCE

GEARBOX DISASSEMBLY

1. Remove 6 cover bolts from input shaft bearing housing (2).

2. Tap around circumference of bearing housing (2) to loosen housing and shims. Then pull complete shaft

(6) and housing assembly out of main housing.

3. Remove 4 capscrews (14), break gasket loose (11 & 12), and then remove the bearing retainer cap (18).

(Mnt-R-0211)

4. Output shaft assembly must be removed from main housing by driving or pulling shaft out bottom end.

NOTE: Once lower bearing is out of housing the complete assembly will drop.

5. The gearbox is now disassembled into four (4) sub-assemblies:

1. Input shaft assembly

2. Output shaft assembly

3. Lower bearing retainer assembly

4. Main housing assembly

1. Housing

2. Lockwasher

3. Bolt

4. Input Cap

5. Input Shaft

6. Input Oil Seal

7. Shim (0.30)

8. Shim (0.50)

9. Input Gasket (0.10)

10. Input Gasket (0.25)

11. Gear Mounting Spacer

12. Output Spacer

13. Output Cap

14. Lockwasher

15. Bolt

16. Cotter Pin

17. Flanged Nut

18. Output Oil Seal

19. Output Cap Gasket (0.10)

20. Output Cap Gasket (0.25)

21. Output Shaft

22. Bearing Assembly

23. 15 Tooth Gear

24. Bearing Adjusting Nut

25. Cotter Pin

26. Bearing Assembly

27. Drain Plug

28. Sealing Washer

29. Spacer

30. 24 Tooth Gear

31. Dip Stick

32. Output Seal Protector

MAINTENANCE

RX60/72/84 10/12 Maintenance Section 5-20

MAINTENANCE

RIGHT ANGLE GEARBOX (OUTBOARD) ASSEMBLY & DISASSEMBLY

PROCEDURES

Input Shaft Removal

Step I.

Place Gearbox on appropriate work surface.

Step II.

Remove Vent Plug (item #32) and Dipstick (item #31).

Step III.

Turn Gearbox upside down allowing Oil to drain from gearbox into catch pan for proper disposal.

Step IV.

Turn Gearbox right side up and drop bottom into a hole for support or lay it on its side laying flat.

Step V.

Remove Bolts (item # 3) from front Bearing Cap (item # 4), this will allow front cover to be removed, It may be

required to drive a wedge between front cover and main housing to loosen cover.

Step VI.

Remove Input shaft (item #5) and Input Gear (item #31), Input Shaft should pull out with Gear and Bearing

Cones (item #27) still on it, Inner Bearing Cone may stay in Housing and Outer Bearing Cone should come off

with front Bearing cover.

Step VII.

Remove Inner Bearing Cone, Inner Spacer (item # 30), Outer Bearing Cone, Input Gear, Check now for Shims

(item # 7& 8) always note quantity of Shims.

Step VIII

Remove Input Seal (item # 6), Bearing Cup (item #27) from front Cover and bearing Cup (item#20) from back

of Main Housing (Casing) (item # 1).

Output Shaft Removal

Step I.

Remove Cotter Pin (item # 26) from Nut (item # 25) and Output Shaft (item # 22) this can be done by reaching

through opening in front of Main Housing. NOTE: Nut is installed with Loctite and may require heating to

remove. Heat nut to approx. 200 F, to ease removal

Step II.

Slide Output (Pinion) Gear (item # 24) up off of Output Shaft and out of Main Housing.

Step lll.

Remove 4 bolts (item # 15), which will allow output cap (item # 13) to be removed. This allows output shaft to

be removed through bottom opening.

MAINTENANCE

RX60/72/84 10/12 Maintenance Section 5-21

MAINTENANCE

Step lV.

Reach in from front or top of Main Housing and remove upper Output Shaft Cone Bearing (item # 23)

Step V.

From the top of Main Housing drive out top and bottom Bearing Cups (item # 23). Spacer (item # 12) will fall out

once lower bearing cup comes out of housing.

Parts Inspection

Step I

Inspect and Clean all Parts. Check Bearings, Shafts, Gears, Housing and Covers. Shafts should be inspected

at Seal wear areas, Bearing areas, Splines, Threads and all surface areas. Check Housings for cracks and

condition of all holes that are threaded. Check Housing and covers where Seals drive in for Burrs and

scratches. If Bearing Cones are replaced always replace Cups with them. Gears should not have and rough

surfaces where the gears run together. On Main Housing remove any old Gasket Sealer, Scratches, Wash and

completely clean it.

Output Shaft Installation

STEP I

Install Upper Output Shaft Bearing Cup (item # 23) into Main Housing from the bottom. NOTE!: Direction

bearing cup must be installed. Insert spacer (item # 12). Install lower bearing cup (item #23) into main housing

and seat firmly against spacer (item # 12)

STEP II

Install Lower Bearing Cone (item #23) down over Output Shaft from top making sure it is firmly seated against

shoulder on Shaft.

STEP III

Insert Output Shaft (item # 22) into Main Housing from the bottom till Lower Bearing Cone is seated into Lower

Bearing Cup, Slide Upper Bearing Cone down over Output Shaft from the till it seats against and into upper

output Shaft Bearing Cup.

STEP IV

Slide Output Gear (item # 24) down over Output Shaft till it sits against upper Bearing Cone. NOTE!: Place one

shim (item # 7) between gear (item # 24) and top bearing.

STEP V

Install Output Shaft Bearing Adjusting nut (item # 25) Tighten Nut to set Pre-Load on Output Shaft Bearings.

Bearing Preload should be from 15 to 25 inch pounds of Rolling Torque.

STEP VI

Using Soft Metal (Brass or Aluminum) Pin, Strike both ends of Shaft with a hammer and recheck the Bearing

Pre-Load, This is to ensure Bearings and components are centered and seated. If Bearing Pre-Load is OK

insert Cotter Pin (item # 26) and Bend ends.

MAINTENANCE

RX60/72/84 10/12 Maintenance Section 5-22

MAINTENANCE

STEP VII

Press new output seal (item # 19) into output cap (item # 13). Using one gasket (item # 20) install lower output

cap into main housing. Retain using bolts and washers (items # 14 & 15). NOTE!: Use gasket sealant between

all parts!

Input Shaft Installation

STEP I

Install Inner Bearing Cup (item # 27) into back of main Housing (item # 1), Make sure Cup is seated into Main

Housing.

STEP II

Install Outer Bearing Cup (item # 27) into back of Front input cap (item # 4). Make sure Cup is Seated into front

cap.

STEP III

Install Spacer (item # 30) onto input Shaft (item # 5) from the front. Install Shims (item # 7 & 8) onto input Shaft

from the front. For quantity of Shims refer to Step 7. Under Input Shaft Removal.

STEP IV

Install Input Gear (item #31) on to Input Shaft from the front, Install Outer Bearing Cone (item # 27) on to input

shaft and slide down till it seats against Gear. Install Inner Bearing Cone (item # 27) Onto input shaft.

STEP V

Insert Input Shaft with all components down into Main Housing till Inner Bearing Cone is seated into Inner

Bearing Cup. Rotate output shaft back & forth slightly to determine approx. gear back lash. If backlash seems

large, it will be necessary to remove a shim (item # 7 or 8). If not enough backlash is present then add a shim

(item 7 or 8). Proper gear backlash is between 0.015" to 0.025".

STEP VI

Input Seal (item # 6) can be installed now or wait till later. With Shims (item # 9&10) lower Input Bearing Cap

(item # 4) down over Input Shaft. Install Bolts (item # 3) into Bearing Cap and tighten them, Check Bearing Pre-

Load. Bearing Preload should be from 12 to 14 pounds of Rolling Torque, if rolling torque is low remove shim

(item# 9 or 10) and if high, add shims. Check backlash of gears again to make sure they are set correctly.

Reshim using shims (items # 7 & 8) as required Once all shims are properly set remove input cap (item # 4)

and apply gasket sealer and reinstall cap and tighten all bolts to recommended torque levels.

STEP VII

Fill Gearbox with Oil, until proper oil level shows on dipstick, Stop and wait about 10 minutes so oil will have

time to run down around Output Shaft bearings then finish filling with oil, This procedure may take longer on

Cold days or Shorter on Hot days. Always recheck Oil Level after gearbox has been run approximately 1/2

hour.

MAINTENANCE

RX60/72/84 10/12 Maintenance Section 5-23

MAINTENANCE

GEARBOX SERVICING (Model RX72)

TOOLS NEEDED FOR DISASSEMBLY AND ASSEMBLY OF GEARBOX

1. Slide Hammer Puller

2. Locktite #5900

3. Punch - Long Drift

4. Needle Nose Pliers

5. Screw Driver

6. External Snap Ring Pliers

7. Socket Wrench

8. 9/16 Socket

9. Ball Pin Hammer

10. Pry Bar

Be certain to clamp or securely support the gearbox and sub-assemblies to prevent injuries

to hands and feet due to inadvertent dropping or falling over.

Always wear safety glasses and gloves to prevent eye and hand injury when chiseling or

hammering on metal components. Hardened metal will chip unexpectedly.

An assembled gearbox is quite heavy. Use a hoist or get help to handle them safely. Lift

carefully and properly using your legs to lift - not your back.

NOTICE: Refer to operator’s manual for instructions for proper re-assembly onto the mower deck. Tighten

correctly.

MAINTENANCE

RX60/72/84 10/12 Maintenance Section 5-24

MAINTENANCE

ITEM QTY DESCRIPTION

1. 1 Casing

1. 1 Crown Wheel

2. 2 Bearing

3. 1 Oil Seal

4. 1 Shaft

5. 2 Internal Clip

6. 2 Shim

7. 1 External Clip

8. 1 Nut

9. 1 Shim

10. 1 Protective Shield

11. 1 Oil Seal

12. 2 Bearing

13. 1 Shaft

14. 1 Bevel Pinion

15. 1 Cotter Pin

16. 1 Shim

17. 1 Plug

18. 1 Cap

19. 4 Hex Bolt

20. 1 Breather Dipstick

21. 1 Cover

22. 1 Shim

23. 1 Nut, Output Shaft

24. 1 Washer, Output Shaft

25. 1 Cotter Pin

MAINTENANCE

RX60/72/84 10/12 Maintenance Section 5-25

MAINTENANCE

Top Input Shaft Preload Setting

Step I.

Drive bearing cup #3 into place on side of gearbox closest to gear. Insert shim #17 if used and install retaining

ring #6. Drive bearing cup #3 back against shim #17 retaining ring #6.

Step II.

Insert bearing cone #3 and gear #2 into approximate locations. Install external clip #8 into proper groove in

shaft #5. Insert shaft #5 into gear #2 and press as far as external clip #8 allows.

Step III.

Press bearing cone #3 onto rear end of shaft #5 against shoulder on shaft. Insert bearing cup #3 and drive into

housing as far as possible. Insert shims #7 against bearing #3 and install internal clip #6.

Step IV.

Tap on input side of shaft #5 and check for end play in bearings. If end play is present additional shims must be

added to rear as in Step 3.

Step V.

Check gear backlash. BAcklash should always be present and should be between 0.12 and 0.020 inches. If

not then shims #7 and #17 must be exchanged between input and rear sides of gearbox. To increase backlash

place a thinner shim on input si9de and thicker shim at rear. To decrease backlash reverse procedure.

Step VI.

Press in all seals and caps and install top cover plate.

Right Angle Gearbox Assembly & Disassembly Procedures

Refer to FIGURE Mnt-R-0404 for location of all item numbers in procedure

REMOVE INPUT SHAFT

Step I.

Place gearbox on appropriate work surface. Remove bolts #20 retaining top cover plate. #22.

Step II.

Drive sharp object (chisel) through seal #4 and force out of housing #1. Repeat procedure for back cap #19.

Step III.

Remove retaining rings #6 from both sides of gearbox. NOTE: Location of shims between bearing and

retaining ring and mark for later installation.

Step IV.

Remove shaft from housing by pressing on splined end of shaft. Bearing cone #3 and gear #2 will remain in

housing. Remove by lifting out. Press bearing cone off rear end of shaft.

MAINTENANCE

RX60/72/84 10/12 Maintenance Section 5-26

MAINTENANCE

Output Shaft Removal

Step I.

Remove protective shield #11 by prying out.

Step II.

Remove cotter pin #16 and slotted nut #9 from top end of output shaft.

Step III.

Using long punch or bar inserted through top drive shaft #14 out bottom end. NOTE: Bearing will push seal out

bottom.

Step IV.

Remove gear #15, shim #10, #23, and bearing cone #13 from main housing. Note and mark shims #10 and

#23 so they may be reused during assembly.

Step V.

Using long punch or bar drive bearing cup #13 from both ends. Press bearing cone #13 from lower end of shaft

#14.

Assembly Procedure

Reassemble gearbox in the reverse order that it was disassembled.

OUTPUT SHAFT PRELOAD SETTING

Tighten nut on top of shaft using 2-3/16 or 55 mm socket. Using hammer tap both ends of shaft to seat parts and then

check preload. Rolling torque should be 15 to 20 inch pounds. Adjust nut to reach setting.

SEGURIDAD

RX60/72/84 10/12 Sección de Seguridad 1-27

SEGURIDAD

RX60/72/84 10/12 Sección de Seguridad 1-26

SEGURIDAD

RX60/72/84 10/12 Sección de Seguridad 1-25

SEGURIDAD

RX60/72/84 10/12 Sección de Seguridad 1-24

SEGURIDAD

RX60/72/84 10/12 Sección de Seguridad 1-23

SEGURIDAD

RX60/72/84 10/12 Sección de Seguridad 1-22

SEGURIDAD

RX60/72/84 10/12 Sección de Seguridad 1-21

SEGURIDAD

RX60/72/84 10/12 Sección de Seguridad 1-20

SEGURIDAD

RX60/72/84 10/12 Sección de Seguridad 1-19

SEGURIDAD

RX60/72/84 10/12 Sección de Seguridad 1-18

SEGURIDAD

RX60/72/84 10/12 Sección de Seguridad 1-17

SEGURIDAD

RX60/72/84 10/12 Sección de Seguridad 1-16

SEGURIDAD

Descripción de Calcomanía

SEGURIDAD

RX60/72/84 10/12 Sección de Seguridad 1-15

SEGURIDAD

INFORMACIÓN DE PARTES

NOTA: Si necessita un manual completamente en español por favor de ponerse en contacto a; Translations,

dirección 1502 E. Walnut Street Seguin, TX 78155; Fax: (830) 372-9529

INFORMACIÓN DE PARTES

Cortacéspedes de ALAMO INDUSTRIAL usan balanceado y componentes del sistema de igualdad para los

portadores de la lámina, las láminas, los cortador-ejes, los cuchillos, las suspensiones del cuchillo, los

rodillos, los componentes del engranajes de conducciòn

y los cojinetes. Estas piezas se hacen y se prueban

a las especificaciones de ALAMO INDUSTRIAL. Partes de No-genuino “caber” piezas no resuelven

constantemente estas especificaciones. El uso de “caber” piezas puede reducir el funcionamiento del

cortacéspedes, garantías vacías del cortacéspedes y presentar un peligro de seguridad. ¡Utilice las piezas

genuinas de cortacéspedes del ALAMO INDUSTRIAL para la economía y la seguridad!

(SPAM-1 SP)

VEA A SU VENDEDOR ALAMO INDUSTRIAL

SEGURIDAD

RX60/72/84 10/12 Sección de Seguridad 1-14

SEGURIDAD

RIESGOS CON EL MANTENIMIENTO DEL IMPLEMENTO

MANTENGA LOS IMPLEMENTOS EN BUENAS CONDICIONES DE FUNCIONAMIENTO, A TRAVÉS DE UN

SERVICIO, REPARACIÓN O MANTENIMIENTO APROPIADO.

ANTES DE REALIZAR TAREAS DE SERVICIO, REPARACIÓN Y MANTENIMIENTO DEL IMPLEMENTO:

ASEGURE EL EQUIPO PARA EL SERVICIO

BLOQUE LOS RIESGOS POTENCIALES DE ENERGÍA;piezas giratorias, componentes levantados, presión hidráulica.

• APAGUE EL MOTOR Y EL PTO, coloque el freno de mano, descienda el implemento, espere a que se detengan todas las partes

móviles y quite la llave antes de bajarse del tractor.

• COLOQUE el implemento sobre el suelo o trabe de manera segura los equipos elevados. Utilice bloques grandes sobre suelo

blando o húmedo.

• CIERRE FIRMEMENTE Y TRABE las alas del implemento levantado.

• TRABE LA LENGUA DEL IMPLEMENTO con bloques grandes y el gato de remolque. NO gateé o trabajar debajo del implemento

solo sostenido por el gato de remolque.

• EMPUJE y JALE la palanca del Cilindro Hidráulico Remoto para liberar la presión hidráulica.

• DESCONECTE las mangueras hidráulicas de implemento del tractor.

• DESCONECTE la línea de conducción del IMPLEMENTO del EJE DE PTO del tractor.

USE GAFAS DE SEGURIDAD y GUANTES PROTECTORES y siga todos los PROCEDIMIENTOS DE SEGURIDAD al realizar

tareas de servicio, reparación y mantenimiento sobre el implemento:

•Siempre USE GUANTES protectores al manipular las hojas, cuchillas, bordes filosos o un componente desgastado con bordes

filosos.

•Siempre USE GUANTES y GAFAS DE SEGURIDAD al reparar componentes en caliente

• EVITE EL CONTACTO con tanques de aceite hidráulico, bombas, motores, válvulas y superficies de conexión de mangueras

calientes.

• SUJETE FIRMEMENTE o TRABE EN POSICIÓN ELEVADA todos los implementos, bastidores y componentes elevados antes de

trabajar sobre los equipos que se encuentran debajo.

• DETENGA el movimiento de todos los implementos y APAGUE EL MOTOR DEL TRACTOR antes de realizar ninguna tarea.

• USE una escalera o gradas elevadas para alcanzar áreas altas del equipo a las que no se pueda acceder desde la tierra.

• ASEGÚRESE de estar bien apoyado sobre superficies sólidas planas al subirse al implemento para realizar tareas.

• SIGA las instrucciones del fabricante sobre cómo manipular los lubricantes, solventes, limpiadores y otros agentes químicos.

• NO cambie ninguna calibración hidráulica de fábrica para evitar fallas de los componentes o equipos.

• NO modifique o altere el implemento, las funciones o componentes.

• NO SUELDE o repare los componentes de la cortadora. Esto puede causar vibraciones y fallas de los componentes que se

desprendan de la cortadora.

REALICE LAS TAREAS DE SERVICIO, REPARACIÓN, LUBRICACIÓN Y MANTENIMIENTO QUE SE DESCRIBEN EN LA

SECCIÓN DE MANTENIMIENTO DEL IMPLEMENTO:

• INS

PECCIONE el implemento para detectar sujeciones sueltas, partes gastadas o rotas, ajustes sueltos o con filtraciones, que los

pasadores tengan chavetas y arandelas, y las partes móviles para detectar el desgaste.

• REEMPLACE todas las partes gastadas o rotas con repuestos autorizados.

• LUBRIQUE la unidad tal como se especifica en el cronograma de lubricación.

• NUNCA lubrique, ajuste o quite material mientras el equipo está en funcionamiento o movimiento.

• AJUSTE todas las tuercas y pernos tal como se especifica.

INSPECCIÓN DE CUCHILLAS:

• REEMPLACE las cuchillas dobladas, dañadas, agrietadas o rotas inmediatamente por cuchillas nuevas.

• EVITE fallas de las cuchillas y que vuelen trozos de cuchillas. NO enderece, suelde o suelde con superficies rígidas.

INSPECCIÓN DE PROTECTORES DE SEGURIDAD, GUARDAS Y DISPOSITIVOS DE SEGURIDAD:

• MANTENGA en su lugar y en buen estado todos los deflectores, protectores de cadena, protectores de acero, cubiertas de caja de

engranajes, cubiertas integrales de PTO, bandas, faldones laterales y zapatas antideslizantes.

• REEMPLACE cualquier protector, cubierta o dispositivo de seguridad faltante, roto o gastado.

• El escape del motor, al igual que algunos de sus componentes, y determinados elementos del vehículo contienen o emiten agentes

químicos que el estado de California ha determinado que causan cáncer, defectos de nacimiento y otros daños reproductivos.

• Las terminales de baterías y los accesorios relacionados contienen plomo y componentes de plomo, que el estado de California ha

determinado son químicos que causan cáncer, defectos de nacimiento u otros daños reproductivos.

PN HM01 SP

SEGURIDAD

RX60/72/84 10/12 Sección de Seguridad 1-13

SEGURIDAD

RIESGOS EN TRANSPORTE

PARA EVITAR LESIONES GRAVES O LA MUERTE AL REMOLCAR O TRANSPORTAR EQUIPOS:

• MANTENGA la velocidad de transporte POR DEBAJO DE 20 millas por hora para mantener el control del equipo.

• REDUZCA LA VELOCIDAD en terreno inclinado, en las curvas y en condiciones de remolque desfavorables.

• NO REMOLQUE camiones u otros vehículos

• USE un tractor de tamaño adecuado y equipado en función del equipo de remolque.

• SIGA todas las reglamentaciones de tránsito locales.

REQUISITOS DEL TRACTOR PARA REMOLCAR O TRANSPORTAR IMPLEMENTOS:

• SÓLO TRANSPORTE en el tractor con el mecanismo ROPS (antivuelco) en posición elevada.

• USE un tractor de tamaño adecuado y equipado, que supere el peso del implemento en al menos un 20%

• MANTENGA EL 20% del peso del tractor en las ruedas frontales para mantener la dirección en forma segura.

ANTES DE TRANSPORTAR O REMOLCAR EL IMPLEMENTO:

INSPECCIÓN DEL TRACTOR:

• VERIFIQUE la dirección y los frenos para asegurarse el correcto funcionamiento y las condiciones adecuadas.

• VERIFIQUE LLEVAR EL AVISO DE SMV, los reflectores y las luces de advertencia para la adecuada operación y

visibilidad detrás de la unidad.

• VERIFIQUE que no haya impedimentos a la visión mientras conduce, en el tractor, la cabina o el implemento,

sentado en el asiento del tractor.

• AJUSTE su posición de conducción, los espejos y el transporte del implemento para tener una visión clara para

condiciones de conducción y tránsito.

PREPARE EL IMPLEMENTO PARA EL TRANSPORTE O EL REMOLQUE:

• DESAPLIQUE EL PTO

• ELEVE LA CORTADORA

• QUITE todo material cortado que se acumule en la plataforma de la cortadora.

CORTADORA AL REMOLQUE-INSTALE

TRABAS DE TRANSPORTE Y CADENA DE SEGURIDAD:

• INSTALE los paradores o pernos de transporte en el cilindro de eje central.

• AJUSTE LA CADENA DE SEGURIDAD del implemento al tractor.

DETERMINAR LAS CARACTERÍSTICAS DE DETENCIÓN DEL TRACTOR Y EL IMPLEMENTO PARA EL

TRANSPORTE O REMOLQUE:

PRUEBAS DE FRENADO:

• FRENE a velocidades en aumento.

• Observe las distancias de DETENCIÓN con el aumento de velocidad.

• DETERMINE la velocidad de transporte máxima segura que no supere las 20 millas por hora

DETERMINE LA VELOCIDAD DE GIRO MÁXIMA ANTES DE OPERAR EN CARRETERAS O TERRENO

IRREGULAR:

• PONGA A PRUEBA el equipo aumentando lentamente la velocidad en las curvas para determinar si se puede

operar a mayor velocidad.

• USE MENORES velocidades de giro en las curvas pronunciadas para evitar el vuelco.

AL REMOLCAR O TRANSPORTAR EL EQUIPO:

• Siempre USE EL CINTURÓN DE SEGURIDAD al operar o transportar la cortadora.

• USE bajas velocidades para evitar el vuelco con el implemento elevado.

• USE bajas velocidades y dirección gradual en las curvas, colinas, o en superficies irregulares o poco uniformes, y en

carreteras mojadas.

• ENCIENDA LAS BALIZAS DE ADVERTENCIA del tractor.

•

TENGA EN CUENTA el espacio necesario para el vaivén del implemento en las curvas. PN TH02 SP

SEGURIDAD

RX60/72/84 10/12 Sección de Seguridad 1-12

SEGURIDAD

RIESGOS ELÉCTRICOS Y DE FUEGO

PARA EVITAR LESIONES GRAVES O LA MUERTE POR CONTACTO ELÉCTRICO AL

TRABAJAR CERCA DE CABLES ELÉCTRICOS, LÍNEAS DE GAS Y DE SERVICIOS:

• INSPECCIONE el área de corte para que no interfiera con cables de alimentación eléctricos subterráneos,

obstrucciones, líneas de gas, cables y servicios, estructuras municipales o de otro tipo.

• MANTENGA todas las alas elevadas a 3 metros (10 pies) o una mayor distancia de todos los cables de

alimentación y obstrucciones elevadas.

• NO ponga en contacto la cortadora con ninguna estructura u obstrucción de servicios o municipales.

• LLAME AL 811 y al 1-800-258-0808 para identificar cables de servicios subterráneos.

PAUTAS DE PREVENCIÓN DE INCENDIOS durante la operación, reparación y servicio de la cortadora y el

tractor, a fin de reducir el riesgo de incendio del equipo y de la vegetación:

• El tractor debe estar EQUIPADO CON MATAFUEGOS

• NO OPERE la cortadora sobre un tractor equipado con escape debajo del bastidor

• NO FUME ni acerque fuego directo a la cortadora o el tractor

• NO CONDUZCA sobre residuos encendidos o en áreas recientemente quemadas

• EVITE LA FORMACIÓN DE CHISPAS al no permitir que la hoja de la cortadora entre en contacto con objetos

sólidos como metal o roca.

• AJUSTE LOS EMBRAGUES DESLIZANTES para evitar el deslizamiento excesivo y el calentamiento de la

placa del embrague.

•

LIMPIE todo resto de hierba o residuo acumulado alrededor de las líneas de conducción de la cortadora, los

embragues deslizantes y cajas de cambios.

• APAGUE EL MOTOR al cargar combustible.

PN EF02 SP

SEGURIDAD

RX60/72/84 10/12 Sección de Seguridad 1-11

SEGURIDAD

RIESGO DE FILTRACION DE ACEITE HIDRÁULICO DE ALTA PRESIÓN

PARA EVITAR LESIONES GRAVES O LA MUERTE POR PENETRACIÓN DE FILTRACIONES DE

ACEITE HIDRÁULICO DE ALTA PRESIÓN:

•NO OPERE el equipo con filtraciones de aceite o combustible.

• MANTENGA todas las mangueras hidráulicas, líneas y conexiones en BUEN ESTADO y AJUSTADAS antes de

aplicar presión al sistema.

• LIBERE LA PRESIÓN HIDRÁULICA antes de desconectar las líneas o trabajar en el sistema.

• QUITE y reemplace la manguera si sospecha que tiene filtraciones. Solicite al distribuidor que verifique si hay

filtraciones.

LAS FILTRACIONES DE LÍQUIDO DE ALTA PRESIÓN PUEDEN NO SER VISIBLES.

AL VERIFICAR FILTRACIONES HIDRÁULICAS Y TRABAJAR CERCA DE LOS SISTEMAS HIDRÁULICOS:

• SIEMPRE USE gafas de seguridad y guantes impenetrables.

• USE papel o cartón para verificar si hay filtraciones.

• NO USE las manos o partes del cuerpo para detectar filtraciones.

• MANTENGA las manos y el cuerpo LEJOS de los orificios de clavijas y boquillas de eyección de fluido hidráulico.

• El fluido hidráulico puede causar gangrena si no es extirpado quirúrgicamente de inmediato por un médico

especializado en este tipo de lesiones.

PN HP01 SP

SEGURIDAD

RX60/72/84 10/12 Sección de Seguridad 1-10

SEGURIDAD

RIESGO DEL CONTACTO A LAS CUCHILLAS DE CORTADORA

MANTÉNGASE LEJOS DE LAS CUCHILLAS GIRATORIAS PARA EVITAR LESIONES GRAVES

O LA MUERTE POR CONTACTO CON LA CUCHILLA:

• MANTÉNGASE LEJOS y NO ACERQUE LAS MANOS, LOS PIES y EL CUERPO a las cuchillas giratorias, líneas

de conducción y partes hasta que todos los elementos móviles se hayan detenido.

• NO ponga las manos o los pies debajo de las plataformas de la cortadora

• DETENGA las CUCHILLAS giratorias antes de elevar la plataforma de la cortadora o las alas

• DETENGA la cortadora, EXAMÍNELA Y PRESTE ATENCIÓN A LOS SONIDOS antes de acercarse a la cortadora

para asegurarse de que se haya detenido todo el movimiento giratorio.

PN MB01 SP

SEGURIDAD

RX60/72/84 10/12 Sección de Seguridad 1-9

SEGURIDAD

RIESGO DE ENREDO POR EL PTO

MANTÉNGASE ALEJADO DE LAS LÍNEAS DE CONDUCCIÓN Y OTROS ELEMENTOS

GIRATORIOS PARA EVITAR LESIONES GRAVES O LA MUERTE:

MANTÉNGASE LEJOS

y NO ACERQUE las manos, los pies y el cuerpo a las cuchillas giratorias, líneas de

conducción y partes hasta que todos los elementos móviles se hayan detenido.

• DETENGA la cortadora, EXAMÍNELA Y PRESTE ATENCIÓN A LOS SONIDOS antes de acercarse a la cortadora

para asegurarse de que se haya detenido todo el movimiento giratorio.

• LOS ELEMENTOS GIRATORIOS SIGUEN ROTANDO una vez apagada la PTO.

PROTECCIÓN DE LA PTO:

PARA EVITAR LESIONES GRAVES O LA MUERTE POR ENREDO AL OPERAR EL IMPLEMENTO:

• MANTENGA instalados los protectores, las cubiertas integrales de las líneas de conducción y las cubiertas de

entrada

• NO OPERE la cortadora si los protectores o cubiertas no están bien colocados o faltan.

• REEMPLACE O REPÁRELOS si faltan, están dañados o rotos

• SIEMPRE REEMPLACE LOS PROTECTORES que se han quitado para tareas de reparación o mantenimiento.

PARA EVITAR que la línea de conducción se rompa durante las operaciones:

• VERIFIQUE que la línea de conducción tenga el largo adecuado entre el eje de PTO y el eje de la caja de cambios

del implemento.

• Las líneas de conducción demasiado cortas se pueden soltar o romper.

• Las líneas de conducción demasiado largas pueden tocar el suelo.

Un ensamblaje telescópico de la línea de conducción que toque el suelo no se deslizará y se solidificará.

• Si la línea de conducción toca el suelo, puede atravesar los cojinetes de soporte y romper el eje de PTO.

• EVITE hacer curvas pronunciadas o elevar la cortadora a alturas que puedan hacer caer la línea de conducción.

• Lubrique los componentes telescópicos del eje de transmisión en forma semanal.

COMUNÍQUESE CON EL DISTRIBUIDOR

si la línea de conducción del implemento no coincide con el eje de

PTO del tractor:

• NO UTILICE UN ADAPTADOR DE PTO.

El uso de un adaptador de PTO puede causar vibración excesiva, caída de objetos, fallas de las cuchillas y el

implemento como consecuencia de la duplicación de la velocidad operativa. El aumento de la longitud de trabajo

puede exponer áreas desprotegidas de la línea de conducción.

PN PE01 SP

SEGURIDAD

RX60/72/84 10/12 Sección de Seguridad 1-8

SEGURIDAD

RIESGO DE ATROPELLO

PARA EVITAR LESIONES GRAVES O LA MUERTE POR CAÍDA DEL TRACTOR O ATROPELLO

DEL EQUIPO:

• USE tractores equipados con SISTEMA ANTIVUELCO (ROPS) y CINTURONES DE SEGURIDAD para las

operaciones de corte.

• MANTENGA EL SISTEMA ROPS trabado en posición vertical.

• SÓLO ENCIENDA el tractor sentado en el asiento del tractor.

• SIEMPRE ABRÓCHESE el cinturón de seguridad al operar el tractor y los equipos.

• SÓLO OPERE el tractor y el equipo sentado en el asiento del tractor.

• NUNCA LLEVE A OTRAS PERSONAS en el tractor o implemento.

AL SUBIR Y BAJAR DEL TRACTOR:

• • SÓLO suba o baje del tractor cuando éste y sus partes móviles estén detenidos.

• • APAGUE EL MOTOR Y LA TDF, coloque el freno de mano, descienda del implemento, espere a que se detengan

todas las partes móviles y quite la llave antes de bajarse del tractor. PN RO01 SP

SEGURIDAD

RX60/72/84 10/12 Sección de Seguridad 1-7

SEGURIDAD

RIESGO DE OBJECTOS LANZADOS Continuado

OPERACIÓN DE LA CORTADORA:

• NO exceda la capacidad de corte nominal de la cortadora, ni corte elementos que no sean vegetación.

• USE CABINAS DE TRACTOR CERRADAS

cuando haya dos o más cortadoras operando en un mismo

sector.

• AJUSTE las secciones de la cortadora o la ala cercana y paralela al suelo sin exponer las cuchillas

• AJUSTE LA ALTURA de corte para EVITAR EL CONTACTO DE LAS CUCHILLAS con objetos sólidos,

como alambres, piedras, postes, cordones, guardarrailes y obstrucciones fijas.

• NO opere la cortadora con la(s) ala(s) elevada(s) o en posición de transporte.

• DETENGA LA CORTADORA de inmediato si las cuchillas entran en contacto con objetos pesados,

estructuras fijas, guardarrailes de metal y estructuras de cemento:

1. LAS CUCHILLAS PUEDEN FALLAR con el impacto y los objetos pueden ser arrojados a gran

velocidad.

2. INSPECCIONE y REEMPLACE las cuchillas dañadas.

3. VERIFIQUE el equilibrio del porta cuchillas y REEMPLÁCELO si está dañado.

• NO opere la cortadora en agua PARA EVITAR una posible FALLA DE LAS CUCHILLAS.

• EVITE OPERAR LA CORTADORA en reversa:

1. DETENGA EL PTO y retroceda la cortadora.

2. DESCIENDA la cortadora, encienda el PTO y corte hacia adelante.

• DETENGA EL PTO y las CUCHILLAS al elevar el implemento o la cortadora a posición de transporte.

• NO ENCIENDA EL PTO con la cortadora en posición de transporte.

• DETENGA la cortadora cuando se produzca VIBRACIÓN EXCESIVA:

1. DETENGA EL PTO Y EL MOTOR del tractor.

2. INSPECCIONE la cortadora para detectar la fuente de la vibración

3. REEMPLACE

toda parte dañada o las CUCHILLAS dobladas o dañadas. PN TO02-X SP

SEGURIDAD

RX60/72/84 10/12 Sección de Seguridad 1-6

SEGURIDAD

RIESGO DE OBJECTOS LANZADOS

LAS CORTADORAS GIRATORIAS PUEDEN ARROJAR OBJETOS A 90 METROS (300 PIES) O MÁS EN

CONDICIONES ADVERSAS.

PARA EVITAR LESIONES GRAVES O LA MUERTE AL OPERADOR O TRANSEÚNTES COMO CONSECUENCIA DE OBJETOS

ARROJADOS:

• MANTENGA a los transeúntes a 100 metros de distancia (300 pies)

NO OPERE LA CORTADORA SI HAY PERSONAS A MENOS DE 100 METROS(300 PIES), SALVO QUE:

• Todos los PROTECTORES CONTRA OBJETOS ARROJADOS estén colocados y en buen funcionamiento al operar la cortadora,

entre los que se incluyen los deflectores frontales y traseros, los protectores de cadena, los protectores de acero, las bandas, los

faldones laterales y las zapatas antideslizantes.

• Las partes de la cortadora o la ala estén ajustadas cerca y paralelas al suelo, sin exponer las cuchillas.

• Se ha inspeccionado el ÁREA DE CORTE y se han quitado todos los materiales extraños y residuos.

• LOS TRANSEÚNTES estén en el interior de un vehículo cerrado.

ANTES DE OPERAR LA CORTADORA, INSPECCIONE EL ÁREA PARA DETECTAR LA POSIBILIDAD DE OBJETOSQUE

PUEDAN SER LANZADOS:

• QUITE residuos, piedras, cables, alambres, objetos metálicos y cualquier otro objetos extraños del área.

Los alambres, cables, sogas, cadenas y objetos metálicos pueden ser arrojados o salir desprendidos de la plataforma a gran

velocidad:

1. MARQUE los objetos que no se puedan quitar.

2. EVITE estos objetos cuando use la cortadora.

INSPECCIÓN DEL ÁREA PARA DETECTAR HIERBA ALTA Y MALEZAS:

• INSPECCIONE Y QUITE cualquier residuo oculto de gran tamaño.

• PASE LA CORTADORA a una altura intermedia

• INSPECCIONE y quite el residuo restante

• PASE LA CORTADORA a la altura final

PROTECCIÓN CONTRA OBJETOS ARROJADOS DE LA CORTADORA:

• MANTENGA todos los protectores contra objetos arrojados en su lugar y en buen funcionamiento al operar la cortadora, entre los

que se incluyen los deflectores frontales y traseros, los protectores de cadena, los protectores de acero, las bandas, los faldones

laterales y las zapatas antideslizantes.

• NO OPERE LA CORTADORA si falta algún protector contra objetos arrojados, o si éstos están dañados.

DERECHO DE PASO (autopista) CON LA CORTADORA

• UTILICE PROTECTORES DE CADENA DOBLES para autopistas, derecho de paso, parques o cortes en cinturón verde donde

pueda haber viviendas, vehículos o ganado dentro de los 100 metros (300 pies) de la cortadora.

• Ninguna protección ofrece una eficacia del 100% en la prevención de objetos arrojados. Para reducir la posibilidad de que se pro-

duzcan lesiones:

1. MANTENGA LOS PROTECTORES DE LA CORTADORA, los faldones laterales, la zapatas antideslizantes y las cuchillas en

buen estado de funcionamiento,

2. ELEVE LA ALTURA DE CORTE a 15 CM (6 PULGADAS) como mínimo,

3. INSPECCIONE EL ÁREA con cuidado antes de pasar la cortadora para ELIMINAR el posible riesgo de OBJETOS

ARROJADOS,

4. NUNCA PERMITA QUE LAS CUCHILLAS EN MOVIMIENTO ENTREN EN CONTACTO CON OBJETOS SÓLIDOS como

alambres, piedras, postes, cordones, guardarrailes o el suelo.

PN TO02 SP

SEGURIDAD

RX60/72/84 10/12 Sección de Seguridad 1-5

SEGURIDAD

RIESGO DE APLASTAMIENTO

PARA EVITAR UNA LESIÓN GRAVE O LA MUERTE POR CAÍDA DEL TRACTOR, O EL APLASTAMIENTO,

VUELCO Y APLASTAMIENTO DE UN EQUIPO POR LA CAÍDA DE UNA ALA O UN IMPLEMENTO:

• USE tractores equipados con SISTEMA ANTIVUELCO (ROPS) y CINTURONES DE SEGURIDAD para las operaciones de

corte.

• MANTENGA EL SISTEMA ROPS trabado en posición vertical.

• SIEMPRE ABRÓCHESE el cinturón de seguridad al operar el tractor y los equipos.

• SÓLO OPERE el tractor y el equipo sentado en el asiento del tractor.

AL ELEVAR O DESCENDER EL IMPLEMENTO:

• Eleve o descienda SÓLO CUANDO ESTÉ SENTADO en el asiento del tractor, con el cinturón de seguridad ajustado.

• Eleve o descienda SÓLO cuando la lengüeta del implemento esté firmemente ajustada a la barra de tracción del tractor

PARA EVITAR el vuelco del implemento.

• MANTENGA A LOS TRANSEÚNTES FUERA del área de operación PARA EVITAR accidentes por aplastamiento.

Los equipos ELEVADOS se pueden caer por fallas mecánicas o hidráulicas o por un movimiento inesperado de la palanca de

control.

PARA EVITAR LA CAÍDA DEL EQUIPO al trabajar cerca o debajo de los componentes o implementos

elevados por un enganche de tractor de 3 puntos:

• SUJETE CON FIRMEZA o bloquee en posición vertical todos los equipos, alas y componentes elevados.

• BLOQUEE EN POSICIÓN VERTICAL y sujete con firmeza el equipo antes de poner las manos, los pies o el cuerpo debajo

de los equipos o componentes elevados.

AL ESTACIONAR el implemento y el tractor:

• DESCIENDA el implemento, TRABE o BLOQUEE las partes elevadas antes de alejarse del equipo.

• NUNCA deje un implemento sin atención en posición elevada.

PARA EVITAR LA CAÍDA O EL APLASTAMIENTO DE NIÑOS POR EL EQUIPO:

• NUNCA DEJE que los niños jueguen sobre el tractor o los implementos, ni en sus alrededores.

WHEN UNHITCHING IMPLEMENT:

AL DESENGANCHAR EL IMPLEMENTO:

• DESCIENDA el implemento, TRABE o BLOQUEE las partes elevadas antes de alejarse del equipo.

• USE el gato de la lengüeta para controlar el movimiento de la lengüeta del implemento

• USE el GATO de le lengüeta para elevar lengüetas de implementos pesados.

• EVITE recargar el gato para evitar falla al gato y una lesión al operador.

PN CH02 SP

SEGURIDAD

RX60/72/84 10/12 Sección de Seguridad 1-4

SEGURIDAD

SEGURIDAD DE CONECTAR O DESCONECTAR IMPLEMENTO

PARA EVITAR LESIONES GRAVES O LA MUERTE POR APLASTAMIENTO POR EL TRACTOR O

IMPLEMENTO:

• AL DAR MARCHA ATRÁS el tractor hacia el enganche del implemento:

• NO PERMITA QUE HAYA PERSONAS entre el tractor y el implemento

ANTES de conectar y desconectar el enganche del implemento:

• APAGUE EL MOTOR DEL TRACTOR, coloque la palanca en “estacionar", ponga el freno de mano y saque la llave.

Al conectar y desconectar el enganche del implemento:

• NO se agache o camine debajo de la cortadora o la ala en posición elevada.

• USE el GATO con lengüeta para elevar lengüetas de implementos pesados a fin de controlar el movimiento de la lengüeta del

implemento.

• EVITE recargar el gato para evitar una falla de éste y una lesión al operador.

AL CONECTAR LA LÍNEA DE CONDUCCIÓN DEL IMPLEMENTO:

PARA EVITAR que la línea de conducción del implemento se suelte durante la operación:

• LUBRIQUE el anillo de cierre del resorte del yugo para asegurarse de que se deslice libremente sobre el eje de PTO

• ASEGURE las bolas de cierre del yugo en la muesca del eje de PTO.

• PRESIONE y JALE DE LA LÍNEA DE CONDUCCIÓN del EJE DE TOMA DE FUERZA(PTO) del tractor y del implemento para

asegurarse de que estén FIRMEMENTE SUJETADOS

PARA EVITAR que la línea de conducción se rompa durante las operaciones:

• VERIFIQUE que la línea de conducción tenga el largo adecuado entre el eje de PTO y el eje de la caja de cambios del implemento.

• Las líneas de conducción demasiado cortas se pueden soltar o romper.

• Las líneas de conducción demasiado largas pueden tocar el suelo.

• Un ensamblaje telescópico de la línea de conducción que toque el suelo no se deslizará y se solidificará.

• Si la línea de conducción toca el suelo, puede atravesar los cojinetes de soporte y romper el eje de PTO.

COMUNÍQUESE CON EL DISTRIBUIDOR si la línea de conducción del implemento no coincide con el eje de TDF del tractor:

• NO UTILICE UN ADAPTADOR DE PTO.

• El uso de un adaptador de PTO puede ocasionar:

• Vibración excesiva, caída de objetos, fallas de la hoja y el implemento como consecuencia de la duplicación de la velocidad opera-

tiva.

• Mayor extensión de trabajo, lo que deja expuestas áreas desprotegidas de la línea de conducción e implica el riesgo de enredo con

otros objetos.

NO conecte la cortadora a un tractor con la TDF directamente conectada a la transmisión del tractor.

PN CD02 SP

SEGURIDAD

RX60/72/84 10/12 Sección de Seguridad 1-3

SEGURIDAD

SEGURIDAD DEL OPERADOR

PARA EVITAR LESIONES GRAVES O LA MUERTE, SIGA LAS SIGUIENTES INSTRUCCIONES:

• LEA, COMPRENDA y SIGA las instrucciones del Manual del Operador, al igual que las Advertencias y Mensajes de

Seguridad.

• USE GAFAS DE SEGURIDAD, calzado protector, casco, protección auditiva y guantes al operar o reparar el equipo

• USE un aparato de respiración apropiado al operar en condiciones polvorientas a fin de evitar contraer

enfermedades respiratorias.

• NO USE prendas sueltas o joyas que se puedan enredar con las partes giratorias y causar una lesión.

• NO CONSUMA DROGAS o ALCOHOL antes o durante la operación del equipo.

• NO PERMITA que nadie opere el equipo bajo los efectos negativos de las drogas o el alcohol.

• CONSULTE a un médico para conocer los efectos desfavorables de la medicación sobre los sentidos.

• MANTÉNGASE ALERTA, la operación prolongada puede causar fatiga. HAGA UNA PAUSA y DESCANSE.

SEGURIDAD DE OPERACIÓN GENERAL

CONDICIONES DE VISIBILIDAD AL USAR LA CORTADORA:

• OPERE LA CORTADORA CON LUZ SOLAR o con luz que aporte una visibilidad nítida de más de 90 metros (100

yardas).

• DEBE PODER VISUALIZAR e identificar transeúntes, terrenos empinados, pozos, desniveles, obstrucciones

elevadas, cables de alimentación, residuos y objetos extraños.

VELOCIDAD RESPECTO AL SUELO AL USAR LA CORTADORA:

• El rango de VELOCIDAD NORMAL es de entre 2 y 5 millas por hora.

• AJUSTE LA VELOCIDAD DE CORTE según las condiciones del terreno y el tipo de césped, la densidad y la altura

del corte.

• REDUZCA LA VELOCIDAD DE CORTE al acercarse a inclinaciones empinadas, pozos, desniveles, obstrucciones

elevadas, cables de alimentación y para evitar residuos y objetos extraños.

INFESTACIÓN CON INSECTOS

• No opere en áreas susceptibles al ataque de abejas o insectos, salvo que USE PRENDAS PROTECTORAS o una

cabina de tractor cerrada.

VELOCIDAD DE PTO:

• NO EXCEDA LA VELOCIDAD DE PTO NOMINAL DEL IMPLEMENTO

• EVITE superar las velocidades nominales de PTO, porque puede causar roturas en la línea de conducción o fallas

de las cuchillas.

SEÑALES DE SEGURIDAD:

• REEMPLACE cualquier señal de seguridad faltante, dañada o ilegible.

PN OS01 SP

SEGURIDAD

RX60/72/84 10/12 Sección de Seguridad 1-2

SEGURIDAD

INSTRUCCIONES DE SEGURIDAD Y PRÁCTICAS GENERALES

El mejor operador es un operador cuidadoso. La seguridad es de importancia fundamental para el fabricante,

y también debería serlo para el propietario u operador. La mayoría de los accidentes se pueden evitar

prestando suma atención al equipo, al ambiente circundante, y tomando algunas precauciones. La primera

sección de este manual incluye una lista de Mensajes de Seguridad que deben observarse para contribuir a

la protección del operador y otras personas frente a lesiones o la muerte. Lea con atención estos Mensajes

de Seguridad antes de ensamblar, operar o reparar este Implemento. Este equipo sólo debe ser operado por

personas que hayan leído el manual, responsables y calificadas, que sepan cómo hacerlo de manera

responsable.

El Símbolo de Alerta de Seguridad se utiliza en combinación con una Señal Verbal, tal como la

que se muestra a continuación, en todo este manual y en los autoadhesivos adheridos a los

equipos. El Símbolo de Alerta de Seguridad significa:

“¡ATENCIÓN! ¡MANTÉNGASE ALERTA! ¡SU SEGURIDAD ESTÁ EN JUEGO!” El Símbolo y

la Señal Verbal tienen el objetivo de advertir al propietario/operador sobre un riesgo inminente y

el grado de lesión que se puede producir al operar este equipo.

Indica una situación peligrosa inminente que, de no ser evitada, OCASIONARÁ la

MUERTE O UNA LESIÓN MUY GRAVE.

Indica una situación peligrosa inminente que, de no ser evitada, PODRÍA OCASIONAR la

MUERTE O UNA LESIÓN MUY GRAVE.

Indica una situación peligrosa inminente que, de no ser evitada, PODRÍA OCASIONAR

UNA LESIÓN MENOR.

Identifica instrucciones o procedimientos específicos que, de no observarse

estrictamente, podrían ocasionar daños o la destrucción de la maquinaria, los accesorios

o el entorno.

NOTA: Identifica aspectos de particular interés para lograr una operación o reparación más eficiente y

conveniente.

LEA CON ATENCIÓN Y RESPETE los siguientes Mensajes de Seguridad. Si no se

siguen cuidadosamente las advertencias e instrucciones indicadas en este Manual y en

los Mensajes de Seguridad del implemento, se pueden producir lesiones graves o la

muerte. Siempre siga las instrucciones de este manual y use el sentido común para evitar

situaciones peligrosas.

NOTA: Si desea obtener una traducción de esta sección de seguridad en alguno de los siguientes idiomas,

comuníquese con: Translations, a la dirección 1502 E. Walnut Street Seguin, TX 78155; Fax: (830) 372-

9529; La Sección de Seguridad está disponible en español, portugués, francés, alemán, ruso.

PN GS01 SP

Adopte todas las medidas habituales para trabajar en forma segura y, sobre

todo, recuerde que la seguridad depende de USTED. Sólo USTED puede

impedir una lesión grave o la muerte a causa de prácticas no seguras.

Sección de Seguridad 1-1

SECCIÓN DE SEGURIDAD

Instrucciones de operaciones antes de la entrega del DISTRIBUIDOR al CLIENTE

El distribuidor deberá informar al comprador de este producto las condiciones, disposiciones y procedimientos de

garantía aplicables; informar la responsabilidad del comprador de capacitar a sus operadores para la operación

segura; revisar el contenido del Manual del Operador, incluido el equipo de seguridad, la operación segura y el

mantenimiento; y revisar las Señales de Seguridad que se encuentran en el implemento (y en el tractor, de ser

posible).

• IMPLEMENTOS: He explicado que los deflectores, protectores de cadena o faldones sólidos se deben

mantener en buenas condiciones de reparación y se deben instalar, excepto en zonas donde personas,

vehículos, ganado u otros bienes no corran peligro por objetos arrojados, y en los casos en que dichos

equipos de seguridad impedirían un desempeño razonable de la cortadora en su tarea asignada.

• LÍNEAS DE CONDUCCIÓN: Me he asegurado de que todos los protectores de líneas de conducción, de caja

de engranajes y otros están en buenas condiciones de reparación y firmemente sujetados para prevenir

lesiones por enredo u objetos arrojados.

• MÁQUINAS HIDRÁULICAS: He explicado la necesidad de usar aceite hidráulico limpio, cambiar los filtros

según las instrucciones, detener filtraciones, prevenir daños por operar con aceite demasiado caliente, cuidar

las mangueras, usar mangueras del tipo correcto, mantener la presión operativa especificada y prevenir el

posible riesgo de que el aceite penetre en la piel.

• IMPLEMENTOS PLEGABLES: He explicado que no es posible proteger contra objetos arrojados cuando el

cabezal está elevado del suelo y que el operador es responsable de verificar que no existan personas en las

inmediaciones. He explicado que el brazo o cabezal de cortadora elevado puede entrar en contacto con

obstrucciones elevados y dañar cables y líneas telefónicas, y posiblemente causar lesiones. He explicado que

el brazo o cabezal extendido, o el brazo retraído, puede entrar en contacto con cables de alimentación y

causar lesiones o la muerte por electrocución, y que el operador es responsable de evitar dichos riesgos.

SERVICIO ANTES DE LA ENTREGA

VERIFIQUE Y AJUSTE O LUBRIQUE SEGÚN SEA NECESARIO

Consulte los detalles en el Manual del Operador

Inspección realizada – Garantía y procedimientos de seguridad explicados – Instalación realizada

LUBRICACIÓN E HIDRÁULICA

 Caja de engranajes (niveles de aceite)

 Nivel de aceite hidráulico (tanque externo)

 Nivel de aceite hidráulico del tractor

 Mangueras hidráulicas (no retorcidas y ajustadas)

 Propulsor de bomba frontal (conjunto ajustado y eje

bien alineado)

CORTADORA

 Pernos de husillo y motor bien ajustados

 Nivel de aceite del husillo

 Pernos de porta cuchillas bien ajustados/pasadores de

retención colocados

 Nivel y altura de corte de la cortadora ajustados

 Cojinetes del eje de corte lubricados

 Todas las piezas metálicas bien ajustadas

 Presión de aire y neumáticos/tuercas de rueda (bien

ajustadas)

 Cojinetes de rueda (verificar, engrasar y hacer carga

previa)

ACCESORIOS E INSTALACIÓN

 Deflectores frontales y traseros

 Accesorios de trituración

 Sentido de giro de las hojas correcto

 Vigas y brazos de eje

 Lengüeta y barras de control (instaladas y ajustadas)

 Todos los pernos, pasadores y tuercas (ajuste

correcto)

CONEXIONES DE CORTADORA A TRACTOR

 Longitud de barra de enganche (verificar y fijar)

 Pivote y conexiones de bastidor en A

 Barras de control (ajustadas iguales)

 Altura de eje (ajustar)

 Altura de corte (ajustar)

 Verificación de pre-operación de kit de montaje

 Aleta de cortadora (ajustar nivel con el centro)

 Aleta de cortadora (verificar operación de elevación

correcta)

 Líneas de conducción C.V. (verificar radio de giro máx.)

 Enganche de tracción (ajuste de altura)

 Piezas metálicas de montaje bien ajustadas

ELEMENTOS DE SEGURIDAD

 Protectores (operación e instalación)

 Embrague de línea de conducción (limitador de ajuste)

(ajustar y poner en marcha)

 Autoadhesivos de seguridad (colocados)

 Manual del Operador (entregado)

 Protector de TDF del tractor (instalado)

 Emblema S.M.V. (instalado de ser necesario)

 Gato con lengüeta (instalación y operación)

 Cadena de remolque de seguridad (instalada)

 Manual de Seguridad de Línea de Conducción ADMA

(entregado)

 Manual de Seguridad de Cortadora AEM (entregado en

porta manual)

 Se mostró el Video de Seguridad de Cortadora AEM al

comprador

Alamo Industrial está dispuesto a suministrar un (1) Video de Prácticas

de Seguridad para Cortadoras AEM

Por favor enviar: Video de Seguridad para el Operador de Cortadoras AEM/FEMA – formato VHS

Video de Seguridad para el Operador de Cortadoras AEM/FEMA – formato DVD

Manual del Operador de la Cortadora

Manual de Seguridad del Operador de la Cortadora AEM

Nombre del solicitante:______________________Teléfono:_________________________

Dirección del solicitante:__________________________________

Ciudad:_______________________________

Estado:_______________________________

Código postal:__________________________

Modelo de cortadora:__________________Número de serie:________________________

Fecha de compra:____________________ Vendedor del distribuidor:_________________

Nombre del distribuidor:________________Dirección del distribuidor:_________________

Enviar por correo a:

AEM Video Services

1502 E. Walnut Street

Seguin, TX 78155

O enviar por fax a:

(830) 372-9529

O enviar por correo electrónico a:

[email protected]

A fin de reducir la tasa de accidentes y mejorar la operación segura de las cortadoras, Alamo Industrial se ha

asociado con otros fabricantes de la industria para desarrollar el video y la guía de Prácticas de Seguridad para

Cortadoras Industriales y Agrícolas AEM/FEMA.

El video explica a los operadores de tractores y cortadoras las prácticas seguras que deben adoptar cuando

utilizan cortadoras industriales y agrícolas. Es importante que todos los operadores de cortadoras aprendan cómo

operar sus equipos de corte y puedan reconocer los posibles peligros que pueden surgir al operar una cortadora.

Este video, en conjunto con el manual del operador de la cortadora y los mensajes de advertencia que se

encuentran en la cortadora, serán muy útiles para complementar este aprendizaje tan importante.

Es posible que su distribuidor autorizado de Alamo Industrial le haya mostrado este video y le haya entregado una

copia en DVD cuando adquirió su cortadora. Si usted o algún operador de cortadora no vio el video: mire el video,

lea este Manual del Operador, y complete la Guía del Video antes de operar su cortadora nueva. Si no comprende

alguna de las instrucciones del video o del manual del operador, o si tiene alguna pregunta acerca de la operación

segura, comuníquese con su supervisor, con el distribuidor o con Alamo Industrial

Si desea recibir una copia del video en VHS, envíe un mensaje de correo electrónico a AEMVideo@alamo-

group.com o un fax al (830) 372-9529, o envíe por correo una copia rellenada del formulario que se encuentra al

dorso de esta página a AEM VHS Video 1502 E Walnut Street, Seguin, TX 78155, y solicite la versión en VHS.

Indique su nombre, dirección postal, modelo de cortadora y número de serie.

Cada uno de los operadores debe recibir capacitación para cada equipo (tractor y cortadora), comprender el uso

previsto, y comprender los posibles peligros antes de operar el equipo.

La informacion y material mecionado en la informacion anterior junto con el Manual de Operador puede asistir en

cumplir con los requisitos de OSHA para el entrenamiento anual del Operador.

REQUISITOS DE ENTRENAMIENTO DEL OSHA

Los seguientes requisitos de entrenamiento se an tomoda del Titulo 29, código de la pieza de regulaciones

federales 1928.57 (a) (6). www.osha.gov

Instrucciones del operador. A la hora de la asignación inicial y por lo menos anualmente después de eso, el

empleador mandará a cada empleado quien opera un tractor agricola o implemento en las practicas de operación

segura y el mantenimiento de el equipo con el cual el empleado esté, o estará implicado y de cualquier otras

prácticas dictados por el ambiente laboral.

Al propietario/operador/distribuidor

Este Manual del Operador es una parte esencial de la operación segura de esta máquina y se debe mantener con

la unidad siempre. El implemento incluye un porta manual donde se puede guardar el manual de manera

adecuada. Si el manual se extravía o se daña, puede solicitar otra copia sin cargo a un distribuidor autorizado de

Alamo Industrial o descargarlo del sitio web de Alamo Industrial (www.www.alamo-industrial.com).

ANTES DE COMENZAR LEA, COMPRENDA y SIGA la información incluida en este manual, el Manual de

Seguridad de la Cortadora AEM y el manual del operador del tractor para conocer cómo operar la máquina y

realizar tareas de servicio correctamente. De lo contrario, podría sufrir lesiones u ocasionar lesiones a terceros.

Todos los implementos con partes móviles son potencialmente peligrosos. Cada esfuerzo ha sido hecho para

asegurar que la màquina esté segura, pero los operadores deben evitar entrar en prácticas peligrosas y seguir las

instrucciones escritas que son proporcionadas. El fabricante ha diseñado este implemento para ser usado con

todos sus equipos de seguridad correctamente sujetados para minimizar la probabilidad de accidentes.

LA SEGURIDAD PRIMERO. Lea con atención la totalidad de la sección de seguridad de este manual antes de

operar el equipo. No permita que nadie opere el equipo sin haber leído y comprendido la totalidad de este manual.

Comuníquese con el distribuidor si necesita explicación sobre alguna instrucción que no haya comprendido del

todo.

Los cuidados que brinde a su Implemento Alamo Industrial determinarán en gran medida su satisfacción con el

desempeño y la vida útil del equipo. Lea con atención y siga las instrucciones de este manual para comprender

cabalmente su nuevo implemento, su uso previsto, y sus requisitos de servicio.

Todas las referencias que se hacen en este manual a derecha, izquierda, frontal, trasero, arriba y abajo

corresponden a la perspectiva en el sentido del desplazamiento hacia delante con el implemento correctamente

sujetado al tractor.

La información sobre repuestos se encuentra por separado en el Manual de Partes. Las cortadoras Alamo

Industrial utilizan componentes del sistema equilibrados y coincidentes para porta cuchillas, cuchillas, ejes de

corte, hojas, ganchos para hojas, rodillos, componentes de los engranajes, y cojinetes. Estas partes se fabrican y

se prueban según las especificaciones de Alamo Industrial. Las partes compatibles no genuinas no siempre

cumplen con estas especificaciones. El uso de partes no genuinas puede perjudicar el desempeño de la cortadora,

anular la garantía y presentar un riesgo para la seguridad. Use partes genuinas Alamo Industrial para ahorrar

dinero y maximizar la seguridad.

Para referencia futura, registre el número de modelo y el número de serie de Alamo Industrial que ha adquirido.

Distribuidor Teléfono Fecha de compra:

Due

ño

Fecha de compra: Número de serie

Placa de Número de serie

RX60/72/84

Publicado en 10/12 Parte nº. 00785503C

MANUAL DE OPERADOR

ALAMO INDUSTRIAL

1502 E. Walnut

Seguin, Texas 78155

830-372-3551

Email: part[email protected]

CORTADORA/TRITURADORA GIRATORIA

Este Manual del Operador es

una parte esencial de la

operación segura de esta

máquina y se debe mantener con

la unidad siempre. LEA

ENTIENDA

, y SIGA las

Instrucciones de Seguridad y

Operación contenidas en este

manual antes de operar el

equipo.

C01-Cover SP_A

Importantes instrucciones

de operación y las

instrucciones de seguridad

se encuentran en el video

Cortacésped Sobre

Seguridad que se puede

acceder instantáneamente

en el internet en:

www.algqr.com/avs

$0.00

Alamo Industrial RX60 Manual de usuario

Marca: Alamo Industrial

Modelo: RX60

Categoría: Cortadoras de césped

Tipo: Manual de usuario

Este manual también es adecuado para

RX72
RX84

Descargar PDF

informe

en otros idiomas

English: Alamo Industrial RX60 User manual

Alamo Industrial RX60 Manual de usuario

Este manual también es adecuado para

Alamo Industrial RX60 Manual de usuario

en otros idiomas

Artículos relacionados

Otros documentos