Yamaha CRX-330 Manual de usuario

Categoría
Receptores AV
Tipo
Manual de usuario
OWNER'S MANUAL
MODE D'EMPLOI
UA
AMPLI-TUNER CD
CD RECEIVER
i En
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert you to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert you to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in accordance with
the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9 Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided
for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
10 Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11 Only use attachments/accessories specified by the manufacturer.
12 Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
13 Unplug this apparatus during lightning storms or
when unused for long periods of time.
14 Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
IMPORTANT SAFETY INSTRUCTIONS
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
IMPORTANT
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
We Want You Listening For A Lifetime
Yamaha and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your
equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or
distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is
often undetectable until it is too late, Yamaha and the Electronic Industries Association’s Consumer Electronics Group
recommend you to avoid prolonged exposure from excessive volume levels.
ii En
FCC INFORMATION (for US customers)
1 IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC,
to use the product.
2
IMPORTANT: When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to
follow instructions could void your FCC authorization to
use this product in the USA.
3 NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15
for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will
not result in harmful interference with other electronic
devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions found
in the users manual, may cause interference harmful to the
operation of other electronic devices.
Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If
this product is found to be the source of interference,
which can be determined by turning the unit “OFF”
and “ON”, please try to eliminate the problem by using
one of the following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch
(circuit breaker or fuse) circuits or install AC line
filter/s.
In the case of radio or TV interference, relocate/
reorient the antenna. If the antenna lead-in is 300 ohm
ribbon lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce
satisfactory results, please contact the local retailer
authorized to distribute this type of product. If you can
not locate the appropriate retailer, please contact
Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe
Ave, Buena Park, CA 90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
The label is located on the bottom of the unit. (U.S.A and
Canada models only)
DANGER:
CAUTION:
AVOID DIRECT EXPOSURE TO THE BEAM
INVISIBLE LASER RADIATION WHEN OPEN
DO NOT STARE INTO BEAM
INVISIBLE LASER RADIATION WHEN OPEN
iii En
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this unit in a well ventilated, cool, dry, clean place with at
least 10 cm on the top, 10 cm on the left and right, and 10 cm at
the back of this unit — away from direct sunlight, heat sources,
vibration, dust, moisture, and/or cold.
3 Locate this unit away from other electrical appliances, motors, or
transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes from cold
to hot, and do not locate this unit in an environment with high
humidity (i.e. a room with a humidifier) to prevent condensation
inside this unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign object may fall onto this
unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
Other components, as they may cause damage and/or
discoloration on the surface of this unit.
Burning objects (i.e. candles), as they may cause fire, damage
to this unit, and/or personal injury.
Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to this
unit.
6 Do not cover this unit with a newspaper, tablecloth, curtain, etc.
in order not to obstruct heat radiation. If the temperature inside
this unit rises, it may cause fire, damage to this unit, and/or
personal injury.
7 Do not plug in this unit to a wall outlet until all connections are
complete.
8 Do not operate this unit upside-down. It may overheat, possibly
causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet, grasp
the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might damage
the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using this unit
with a higher voltage than specified is dangerous and may cause
fire, damage to this unit, and/or personal injury. Yamaha will not
be held responsible for any damage resulting from use of this unit
with a voltage other than specified.
13 To prevent damage by lightning, keep the power cord and
outdoor antennas disconnected from a wall outlet or this unit
during a lightning storm.
14 Do not attempt to modify or fix this unit. Contact qualified
Yamaha service personnel when any service is needed.
The cabinet should never be opened for any reasons.
15 When not planning to use this unit for long periods of time (i.e.
vacation), disconnect the AC power plug from the wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit is
faulty.
17 Before moving this unit, press STANDBY/ON to set this unit to
the standby mode, and disconnect the AC power plug from the
wall outlet.
18 Condensation will form when the surrounding temperature
changes suddenly. Disconnect the power cable from the outlet,
then leave this unit alone.
19 When using this unit for a long time, this unit may become warm.
Turn the power off, then leave this unit alone for cooling.
20 Install this unit near the AC outlet and where the AC power plug
can be reached easily.
21 The batteries shall not be exposed to excessive heat such as
sunshine, fire or the like.
22 Excessive sound pressure from earphones and headphones can
cause hearing loss.
LASER SAFETY
This unit employs a laser. Due to possible eye injury, only a
qualified service person should remove the cover or attempt to
service this device.
DANGER
This unit emits visible laser radiation when open. Avoid direct
eye exposure to beam.
When this unit is plugged into the wall outlet, do not place your
eyes close to the opening of the disc tray and other openings to
look into inside.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
This unit is not disconnected from the AC power source as
long as it is connected to the wall outlet, even if this unit itself
is turned off by STANDBY/ON. This state is called the
standby mode. In this state, this unit is designed to consume a
very small quantity of power.
The laser component in this product is capable of emitting
radiation exceeding the limit for Class 1.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
1 En
English
PREPARATIONINTRODUCTION
TUNER
OPERATIONS
OTHER
OPERATIONS
ADDITIONAL
INFORMATION
BASIC
OPERATIONS
FEATURES............................................................. 2
SUPPLIED ACCESSORIES ................................. 2
CONTROLS AND FUNCTIONS ......................... 3
Front panel.................................................................3
Front panel display .................................................... 4
Remote control........................................................... 5
CONNECTING SPEAKERS ................................ 9
Connecting a subwoofer .......................................... 10
CONNECTING ANTENNAS.............................. 11
Connecting the FM antenna..................................... 11
CONNECTING THE POWER CABLES .......... 11
CONNECTING HEADPHONES........................ 11
CONNECTING EXTERNAL COMPONENTS...12
Connecting a USB device........................................ 12
Connecting an iPod™.............................................. 12
BASIC RECEIVER OPERATIONS .................. 13
SETTING THE SLEEP TIMER......................... 14
BASIC PLAYBACK OPERATIONS FOR DISCS
AND USB DEVICES........................................ 15
Switching the playback information display ........... 16
Repeating playback (Repeat Play)........................... 17
Playing back randomly (Shuffle Play)..................... 17
FM TUNING......................................................... 18
Automatic tuning ..................................................... 18
Manual tuning.......................................................... 18
Automatic preset tuning........................................... 18
Manual preset tuning ............................................... 19
Selecting preset stations........................................... 19
CONTROLLING iPod™......................................20
Using iPod™ ........................................................... 20
TROUBLESHOOTING .......................................22
General..................................................................... 22
Radio reception........................................................ 22
iPod™...................................................................... 23
USB ......................................................................... 23
Disc Playback .......................................................... 24
Remote control ........................................................ 24
NOTES ABOUT DISCS/MP3, WMA FILES.....25
GLOSSARY...........................................................27
Audio information ................................................... 27
Copyright and logo marks ....................................... 27
SPECIFICATIONS...............................................27
CONTENTS
INTRODUCTION
PREPARATION
BASIC OPERATIONS
TUNER OPERATIONS
OTHER OPERATIONS
ADDITIONAL INFORMATION
FEATURES
2 En
Maximum RMS output power per channel
20W + 20W (10% THD, 1 kHz, 6Ω)
30-station FM preset tuning
iPod playability
Plays Audio CDs, MP3/WMA discs
CD Text data display
MP3/WMA file playability stored on USB
device
Multi function remote control
About this manual
This manual describes how to operate this unit using a remote control except when it is not available. Some of these operations are
also available using the front panel buttons.
The round shaped button on the center of the remote control is called Center in this manual.
y indicates a tip for your operation.
Notes contain important information about safety and operating instructions.
This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In
case of differences between the manual and the product, the product has priority.
This product includes the following accessories. Before connecting speakers, make sure you received all of the following parts.
FEATURES
SUPPLIED ACCESSORIES
STANDBY ON
CD iPod
FM
USB
SLEEP
FM
PRESET
FUNCTION
MENU
DISPLAY
FOLDER
SHUFFLE REPEAT
MUTE
VOLUME
TUNING
MEMORY
USB
iPod
Indoor FM antennaRemote
control
USB cap
*
Dock cover
*
*
The USB cap and the Dock cover are supplied with this unit to cover the USB port and the iPod terminal when not using.
When the USB cap and the Dock cover are covered.
(Other models)
(U.S.A and Canada
models)
3 En
English
INTRODUCTION
1 STANDBY/ON
Turns this unit on or sets it to the standby mode.
2 Disc Tray
Loads a disc to be played back.
3 Front panel display
Shows the various information such as the tuning
frequency.
4
Opens and closes the disc tray.
5 PHONES
Outputs audio signals for private listening with
headphones.
6 Remote control sensor
Receives signals from the remote control.
7 VOLUME
Adjusts the volume level.
8 INPUT
Selects an input source.
9
Stops playback (see page 15).
0
Starts or pauses playback (see page 15).
A USB port
Connect your USB device (see page 12).
B iPod terminal
Connect your iPod (see page 12).
CONTROLS AND FUNCTIONS
Front panel
USB
IPod
A
B
Top view
STANDBY ON
PHONES
VOLUME
INPUT
5
12
3 4
67 8
90
Front view
4 En
CONTROLS AND FUNCTIONS
1 SLEEP indicator
Lights up when the sleep timer is on (see page 14).
2 PRESET indicator
Lights up when you preset radio stations (see page 19).
3 STEREO indicator
Lights up when this unit is receiving a strong signal from
an FM stereo broadcast.
4 AUTO indicator
Lights up when this unit is in the Automatic Tuning mode
(see page 18).
5 SHUFFLE indicator
Lights up when you set your iPod/CD/USB in shuffle
mode.
6 REPEAT indicator
Lights up when you set your iPod/CD/USB in repeat
mode.
7 MUTE indicator
Lights up when the sound is muted.
8 Multi information display
Shows the various information such as the tuning
frequency.
9 TUNED indicator
Lights up when this unit is tuned into a station.
0 MEMORY indicator
Lights up when you preset radio stations automatically or
manually.
A Multi information indicator
Light up the menu currently selected (see page 20).
B Operation indicators
Show operable cursor keys when operating with the
FUNCTION or iPod menu with the menu browse mode
(see page 20).
Front panel display
GENRES
SONGS
ALBUMS
ARTISTSPLAYLISTS
MEMORY
TUNED
SLEEP
STEREO
AUTO
SHUFFLE
REPEAT
MUTE
PRESET
1 234 756
9A
B
8
0
5 En
CONTROLS AND FUNCTIONS
English
INTRODUCTION
This remote control can operate the system components
and an iPod stationed in a terminal on the top panel of this
unit.
To operate the CD, USB device, tuner functions, or an
iPod using the remote control, you need to set this unit to
the corresponding input mode.
To switch the input mode of this unit
Press the corresponding input selection key on the remote
control (or INPUT on the front panel). The input mode
automatically changes to iPod when you connect the iPod
during the playback (see page 12).
The name of the corresponding input source appears in the
front panel display of this unit.
Common functions
Operations common to all modes
The following operations are available for this unit when
it is set to any input mode.
1 Infrared signal transmitter
Sends signals to the component you want to control.
2 STANDBY/ON
Turns this unit on or sets it to the standby mode.
3 Input selection keys
Select the input source.
4 FUNCTION
By pressing FUNCTION, you can select DIMMER,
TREBLE, BASS, BALANCE, or ECO MODE.
5 DISPLAY
Switches the information shown in the front panel display
(see page 16).
6 MUTE
Turn off the sound. To restore the sound, press MUTE
again or press VOLUME (down)/ (up).
7 SLEEP
Sets the sleep timer (see page 14).
8 VOLUME (down) / (up)
Adjusts the overall volume level.
Remote control
STANDBY ON
CD iPod
FM
USB
SLEEP
FM
PRESET
FUNCTION
MENU
TUNING
MEMORY
Input
selection
keys
STANDBY ON
CD iPod
FM
USB
SLEEP
FM
PRESET
FUNCTION
MENU
DISPLAY
FOLDER
SHUFFLE REPEAT
MUTE
VOLUME
TUNING
MEMORY
3
2
1
4
7
6
8
5
6 En
CONTROLS AND FUNCTIONS
CD/USB mode Operations available in CD/USB mode
The following operations are available for this unit when
the CD or USB mode is selected.
1 ,
Skips to the beginning of the current track or next track.
Press and hold to fast reverse or fast forward (see
page 15). Press twice to skip to the beginning of the
previous track.
2 DISPLAY
Switches the disc/USB information shown in the front
panel display (see page 16).
3 FOLDER /
Press FOLDER / to playback a first file of
selected folder for an MP3 or a WMA folder recorded on
disc/USB device (see page 15).
*During Shuffle Play, these buttons cannot be used.
4
Starts or pauses playback (see page 15).
5
Stops playback (see page 15).
6 REPEAT
Selects the Repeat Play mode (see page 17).
7 SHUFFLE
Select the Shuffle Play feature (see page 17).
FM mode
Operations available in FM mode
The following operations are available for this unit when
the FM mode is selected.
1 TUNING /
Press TUNING / to Manual tuning and press and
hold TUNING / to Automatic tuning.
2 PRESET /
Press PRESET / to select a preset station (see
page 18).
3 MEMORY
Starts preset memory mode.
4 Center
Press Center to fix the current setting.
STANDBY ON
CD iPod
FM
USB
SLEEP
FM
PRESET
FUNCTION
MENU
DISPLAY
FOLDER
SHUFFLE REPEAT
MUTE
VOLUME
TUNING
MEMORY
3
2
1
7
5
6
4
STANDBY ON
CD iPod
FM
USB
SLEEP
FM
PRESET
FUNCTION
MENU
DISPLAY
FOLDER
SHUFFLE REPEAT
MUTE
VOLUME
TUNING
MEMORY
4
2
1
3
7 En
CONTROLS AND FUNCTIONS
English
INTRODUCTION
iPod mode
Operations available in iPod mode
The following operations are available for the iPod
stationed in the terminal. For details on iPod operations,
see “Using iPod™” on page 20.
1 FUNCTION
Switches between the simple remote mode and menu
browse mode.
2 Center
Press Center to enter the selected group. (Pressing Center
starts playback when a song is selected.)
3
Skips to the beginning of the current track. Press and hold
to fast reverse. Press twice to skip to the previous track.
4 DISPLAY
Displays the song information while iPod is in menu
browse mode (see page 16).
5
Starts or pauses playback.
6 SHUFFLE
Selects the shuffle playback mode (see page 21).
7 MENU
Returns to the upper level in the iPod menu.
8
Skips to the next track. Press and hold to fast forward.
9 /
Press or to select an item in the selected group.
0 REPEAT
Selects the repeat playback mode (see page 21).
The supplied remote control has the same function
keys with your iPod. So, these keys are corresponding
with each other.
STANDBY ON
CD iPod
FM
USB
SLEEP
FM
PRESET
FUNCTION
MENU
DISPLAY
FOLDER
SHUFFLE REPEAT
MUTE
VOLUME
TUNING
MEMORY
4
1
3
2
5
7
8
6
0
9
iPod Remote Control
8 En
CONTROLS AND FUNCTIONS
Preparing the remote control
The remote control comes with the battery already
installed. Before using the remote control for the very first
time, pull out the insulation sheet, as shown.
y
Remove the transparent sheet before using the remote control.
Using the remote control
Use the remote control within 6 m (20 feet) of the
component you want to control and point it toward its
remote control sensor (see page 3).
Be careful not to spill liquid on the remote control.
Be careful not to drop the remote control.
Do not leave the remote control in the following places:
hot or humid places, such as near a heater or in a bathroom
extremely cold places
dusty places
Replacing the battery in the remote control
Change the battery when the operation range of the remote control decreases.
Insert the battery according to the polarity markings (+ and -).
If the battery runs out, immediately remove it from the remote control to prevent an explosion or acid leak.
If the battery starts leaking, dispose of it immediately. Be careful not to let the leaking battery acid touch your skin or clothing.
Before inserting a new battery, wipe the compartment clean.
Dispose of batteries according to your regional regulations.
Insulation sheet
Notes
STANDBY ON
PHONES
VOLUME
INPUT
30˚ 30˚
STANDBY ON
CD iPod
FM
USB
SLEEP
FM
PRESET
FUNCTION
MENU
DISPLAY
FOLDER
SHUFFLE REPEAT
MUTE
VOLUME
TUNING
MEMORY
Within 6 m
(20 feet)
Notes
Use a straight pin to
remove the cover.
Replace the battery
with a new CR2025 battery.
Close the cover.
CONNECTING SPEAKERS
9 En
English
PREPARATION
Follow the procedure below to connect speakers to this unit. For information on your speakers, refer to the owner’s
manual supplied for the speakers.
Do not connect the power cable of this unit until all cable connections are completed.
Be sure to connect the left channel (L), right channel (R), “+”(red) “–”(black) properly. If the connections are faulty, no sound will be
heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lacks bass.
Do not let the bare speaker wires touch each other or do not let them touch any metal part of this unit. This could damage this unit and/
or the speakers.
Use speakers with the specified impedance shown on the rear panel of this unit.
CONNECTING SPEAKERS
CAUTION
Notes
SUBWOOFER
OUT
FM ANT
75 UNBAL
SPEAKERS
TUNER
MAINS
R L
Right speaker
Speaker cables
Left speaker
Rear panel
CONNECTING SPEAKERS
10 En
1 Remove approximately 10 mm (3/8 in) of
insulation from the end of each speaker
cable and then twist the exposed wires of the
cable together to prevent short circuits.
2 Press and hold the lever.
3 Insert one bare wire. By releasing the lever,
the lever is replaced.
Notes on the speaker cord
A speaker cord is actually a pair of insulated cables
running side by side. One cable is colored or shaped
differently, perhaps with a stripe, groove or ridge. Connect
the striped (grooved, etc.) cable to the “+”(red) terminals
on this unit and your speaker. Connect the plain cable to
the “–”(black) terminals on this unit and your speaker.
The low frequency range of the left channel and the right
channel are mixed to output at the SUBWOOFER OUT
jack.
Connect the SUBWOOFER OUT jack on this unit
to the INPUT jack on the subwoofer using the
subwoofer cable (commercially available).
Do not connect the power cable of this unit and the subwoofer
until all cable connections are completed.
10 mm (3/8 in)
Red: positive (+)
Black: negative (–)
Red: positive (+)
Black: negative (–)
Connecting a subwoofer
Note
SUBWOOFER
OUT
TUN
INPUT
INPUT
Subwoofer cable
(commercially
available)
Subwoofer
(commercially
available)
CONNECTING ANTENNAS
11 En
English
PREPARATION
To enjoy radio on this unit, connect the supplied FM antenna to the designated terminals. If there is a problem of weak
radio wave reception in your area or you want to improve radio reception, we recommend that you use commercially
available outdoor antennas. For details, consult the nearest authorized Yamaha dealer or service center.
1 Connect the supplied indoor FM antenna to
the FM jack of this unit.
2 Place the antenna away from this unit and
speaker cables.
After you made all connections, connect the power cables of this unit and subwoofer (optional).
You can connect your headphones to the PHONES jack on the front panel of this unit.
The sound from the speakers stops.
CONNECTING ANTENNAS
SUBWOOFER
OUT
FM ANT
75 UNBAL
TUNER
Indoor FM
antenna
(supplied)
Connecting the FM antenna
CONNECTING THE POWER CABLES
SUBWOOFER
OUT
FM ANT
75 UNBAL
SPEAKERS
TUNER
6 MIN. SPEAKER
MAINS
R L
To an AC wall outlet
CONNECTING HEADPHONES
STANDBY ON
PHONES
VOLUME
INPUT
CONNECTING EXTERNAL COMPONENTS
12 En
You can connect a USB device or an iPod to this unit. For information on your component, refer to the owner's manual
supplied with the component.
This unit has a USB port and can access MP3 or WMA
files saved on your USB device. Connect your USB
device to the USB port on the top panel of this unit.
For playback information of a USB device, see page 15.
Supported USB devices
This unit supports USB mass storage class devices (e.g.,
flash memories) using FAT16 or FAT32 format.
Some devices may not work properly even if they meet the
requirements.
If your USB device is not played back after you connected it to
this unit, follow any of the procedures below.
Set this unit to the standby mode, and turn it on again.
Disconnect the device while this unit is in the standby mode.
Then connect the device again and turn on this unit.
Connect an AC adapter if supplied with the device.
If the USB device is not played back even after you performed
the procedure(s) above, the device may not be playable on this
unit.
Do not connect devices other than USB mass storages class
devices.
Yamaha and suppliers accept no liability for the loss of data
saved on the USB devices connected to this unit.
As a precaution, it is recommended that the files are made
backup copies.
Playability of and power supply to all kind of USB devices are
not guaranteed.
Your USB device is automatically charged when your USB
device is connected to the USB port even when this unit is in
standby mode and ECO MODE is OFF.
To remove USB device safely, disconnect after the playback is
stopped.
This unit equips the iPod terminal on the top panel where
you can directly station your iPod and control playback of
your iPod using the supplied remote control.
Use this unit with the iPod dock adapter (supplied with
your iPod or commercially available) appropriate for your
iPod. If you use this unit without using an appropriate
iPod dock adapter, loose connection may result.
Only iPod (Click and Wheel), iPod nano, iPod mini, and iPod
touch are supported.
Do not connect any iPod accessories (such as headphones, a
wired remote control, or an FM transmitter) to our iPod when it
is stationed in the terminal.
Unless your iPod is firmly stationed in the terminal, audio
signals may not be output properly.
Once the connection between your iPod and this unit is
complete, “iPod” appears in the front panel display. If the
connection between your iPod and this unit fails, a status
message appears in the front panel display. For a complete list
of connection status message, see the iPod section in
“TROUBLESHOOTING” on page 23.
Your iPod is automatically charged when your iPod is stationed
in the terminal even when this unit is in standby mode and ECO
MODE is OFF.
To remove iPod safely, disconnect after the playback is
stopped.
CONNECTING EXTERNAL COMPONENTS
Connecting a USB device
Notes
STANDBY ON
PHONES
VOLUME
INPUT
USB
iPod
USB device
Connecting an iPod™
Notes
STANDBY ON
PHONES
VOLUME
INPUT
USB
iPod
iPod
BASIC RECEIVER OPERATIONS
13 En
English
BASIC
OPERATIONS
Follow the procedure below to select an input source and adjust the sound settings on this unit.
1 Press STANDBY/ON to turn on this unit.
The front panel display lights up.
2 Press one of the input selection keys or
press INPUT on the front panel to select the
desired input source. Each time you press
INPUT, the input source changes in order of
CD, iPod, FM and USB.
3 Start playback on the selected source
component or select a radio station.
For information on the disc playback, see page 15,
and for information on tuning, see page 18.
4 Press (down) / (up) to adjust the
volume to the desired output level.
To adjust the audio quality
1 Press FUNCTION to display the function
menu.
2 Press / repeatedly to select TREBLE,
BASS, or BALANCE and press Center.
3 Press / repeatedly to adjust the
setting and press Center.
TREBLE: Adjusts the high frequency response.
BASS: Adjusts the low frequency response.
BALANCE: Adjusts the volume level of each left
and right speaker channel.
y
TREBLE, BASS, and BALANCE are not adjustable when using
the headphones.
To dim the display
You can dim the front panel display of this unit.
1 Press FUNCTION to display the function
menu.
2 Press / repeatedly to select DIMMER
and press Center.
Press / to select the brightness and press
Center.
To use the ECO mode
This mode reduces power consumption during the standby
mode. Your iPod or USB device cannot be charged during
standby mode and ECO MODE is ON.
1 Press FUNCTION to display the function
menu.
2 Press / repeatedly to select ECO
MODE and press Center.
3 Press / to select ON or OFF and press
Center.
BASIC RECEIVER OPERATIONS
STANDBY ON
PHONES
VOLUME
INPUT
STANDBY ON
CD iPod
FM
USB
SLEEP
FM
PRESET
FUNCTION
MENU
DISPLAY
FOLDER
SHUFFLE REPEAT
MUTE
VOLUME
TUNING
MEMORY
VOLUME INPUT
STANDBY/ON
VOLUME
/
Input
selection
keys
FUNCTION
Center
/
STANDBY/ON
SETTING THE SLEEP TIMER
14 En
The sleep timer sets this unit to the standby mode after the specified time elapses.
Press SLEEP repeatedly to select the desired
duration.
Each time you press the key, the duration changes as
follows.
The SLEEP indicator lights up in the front panel display.
y
The sleep timer is canceled if you set this unit to the standby
mode.
If you press SLEEP while the sleep timer is set, the remaining
time appears in the front panel display.
To cancel the sleep timer
Press SLEEP repeatedly to select “SLEEP OFF”.
SETTING THE SLEEP TIMER
STANDBY ON
CD iPod
FM
USB
SLEEP
FM
PRESET
FUNCTION
MENU
DISPLAY
FOLDER
SHUFFLE REPEAT
MUTE
VOLUME
TUNING
MEMORY
SLEEP
SLEEP 30min
SLEEP 60min
SLEEP 90min
SLEEP 120min
SLEEP OFF
BASIC PLAYBACK OPERATIONS FOR DISCS AND USB DEVICES
15 En
English
BASIC
OPERATIONS
You can enjoy playback your audio CDs, USB devices, and MP3 or WMA files recorded on a disc/USB device. Some
operations may be different or restricted depending on the disc/USB device. Before playing back, check the
compatibility of your disc/USB device with this unit (see page 25).
To start disc playback
1 Select CD as the input source (see page 13).
2 Press while a disc is loaded.
For an audio CD, playback starts from the first track,
and for MP3 or WMA files, playback starts in
alphanumeric order by the filename.
y
You can open and close the disc tray by pressing on the
front panel of this unit.
You can also start disc playback by pressing on the front
panel.
When the input source is CD and this unit is turned on with a
disc loaded, disc playback starts automatically.
To start USB device playback
1 Select USB as the input source (see page 13).
2 Connect your USB device to the USB port on
this unit.
The reading time may exceed 30 seconds depending
on the number of files/folders.
For a USB device, playback starts automatically in
order by the date and time of creation if playable files
are in the USB device.
Total time does not appear on the front panel for USB device
playback.
If the USB device is partitioned, only the first partition is
displayed.
Some files may not work properly depending on the USB
device specification.
Copyright-protected files cannot be played back.
This unit can play back files of 4 GB in size or less.
When the input source is USB and this unit is turned on with the
USB device connected, playback starts automatically.
To stop playback
Press .
To pause playback
Press .
To return to normal playback, press .
To fast reverse or fast forward
To fast reverse, hold down .
To fast forward, hold down .
To skip tracks
To skip to the start of the current track, press .
To skip to the next track, press .
To skip to the previous track, quickly press twice.
To skip a folder for an MP3 or WMA file
To skip a folder, press FOLDER / .
About MP3 and WMA discs/USB device
You can play back MP3 or WMA files recorded on your
CD-R, CD-RW or USB device. This unit regards files in
the disc/USB device as tracks (as shown above).
BASIC PLAYBACK OPERATIONS FOR DISCS AND USB DEVICES
Notes
STANDBY ON
CD iPod
FM
USB
SLEEP
FM
PRESET
FUNCTION
MENU
DISPLAY
FOLDER
SHUFFLE REPEAT
MUTE
VOLUME
TUNING
MEMORY
FOLDER
/
/
Root
Folder
File
BASIC PLAYBACK OPERATIONS FOR DISCS AND USB DEVICES
16 En
You can switch the disc playback information shown in the front panel display of this unit. Available information differs
depending on the type of the disc/USB device.
Press DISPLAY repeatedly while playing back a
disc/USB device.
Each time you press the key, the information display
changes as described in “Playback information for audio
CDs” and “Playback information for MP3 or WMA files
recorded on discs/USB devices” on page 16.
Some special characters may not be shown properly.
Playback information for audio CDs
The following information is available during playback of an audio CD. “Track Title”, “Artist”, and “Album Title” are
available only for a CD TEXT disc.
You can switch the playback information 1 2 5 6 7 above during playback of your iPod in the menu browse mode (see page 21).
Playback information for MP3 or WMA files recorded on discs/USB devices
The following information is available during playback of an MP3 or WMA files recorded on discs/USB device.
Switching the playback information display
FM
PRE
S
ET
FUNCTION
MENU
DISPLAY
FOLDER
SHUFFLE REPEAT
TUNING
MEMORY
DISPLAY
Note
Note
SONGS
ARTISTS
ALBUMS
1 Elapsed time of the current track (Default)
2 Remaining time of the current track
3 Total time of the disc
4 Remaining time of the disc
7 Album Title
6 Artist
5 Track Title
SONGS
ARTISTS
ALBUMS
2 File Name
1 Elapsed time of the current file
4 Artist
5 Album Title
3 Track Title
BASIC PLAYBACK OPERATIONS FOR DISCS AND USB DEVICES
17 En
English
BASIC
OPERATIONS
You can repeat the playback of the selected item in your
disc/USB device.
1 Play back the disc or track you want to repeat.
2 Press REPEAT to select the desired Repeat
Play mode.
Each time you press the key, the Repeat Play mode in
the front panel display changes as follows.
To cancel Repeat Play
Press REPEAT repeatedly so that the Repeat Play mode
indicator disappears from the front panel display or press
.
You can play back tracks in your disc/USB device in
random order.
When playing back with Shuffle Play, the remaining time of the
disc cannot be displayed.
Press SHUFFLE.
Each time you press the key, the Shuffle play mode in the
front panel display changes as follows.
* The SHUFFLE FOLDER means tracks in the folder is play
back in randomly.
To cancel Shuffle Play
Press SHUFFLE repeatedly so that the SHUFFLE
indicator disappears from the front panel display or press
.
Repeating playback
(Repeat Play)
REPEAT
STANDBY ON
CD iPod
FM
USB
SLEEP
FM
PRESET
FUNCTION
MENU
DISPLAY
FOLDER
SHUFFLE REPEAT
MUTE
VOLUME
TUNING
MEMORY
Audio CD
REPEAT ONE (Repeat Play by track)
REPEAT ALL (Repeat Play by disc)
Off (Normal playback)
MP3/WMA disc/USB device
REPEAT ONE (Repeat Play by track)
REPEAT FOLDER (Repeat Play in the folder)
REPEAT ALL (Repeat Play by disc)
Off (Normal playback)
Playing back randomly
(Shuffle Play)
Note
STANDBY ON
CD iPod
FM
USB
SLEEP
FM
PRESET
FUNCTION
MENU
DISPLAY
FOLDER
SHUFFLE REPEAT
MUTE
VOLUME
TUNING
MEMORY
SHUFFLE
SHUFFLE FOLDER
*
SHUFFLE ALL
Off
Audio CD
SHUFFLE ALL
Off
MP3/WMA disc/USB device
FM TUNING
18 En
There are 2 tuning methods: automatic and manual. Automatic tuning is effective when station signals are strong and
there is no interference. If the signal from the station you want to select is weak, tune into it manually. You can also use
the automatic and manual preset tuning features to store up to 30 stations.
Automatic tuning is effective when station signals are
strong and there is no interference.
1
Press FM to set this unit to the FM mode.
2 Press and hold TUNING / to begin
automatic tuning.
The AUTO indicator lights up on the front panel
display.
This unit automatically detects radio stations that
have strong signals for your selection, and
automatically ends automatic tuning.
The AUTO indicator disappears from the front panel
display.
If the signal received from the station you want to select is
weak, tune into it manually.
1
Press FM to set this unit to the FM mode.
2 Press TUNING / repeatedly to tune into
the desired station manually.
y
Manually tuning into an FM station automatically switches the
tuner to monaural reception to increase the signal quality.
Follow the procedure below to preset radio stations
automatically.
1
Press FM to set the unit to the FM mode.
2 Press and hold MEMORY for more than 2
seconds.
The “AUTO PRESET” and “Push Center Key”
appear in the front panel display alternately.
To cancel, press MEMORY.
3 Press Center to start searching
automatically.
Auto Preset starts at the lowest frequency toward
the highest frequency.
This unit automatically applies a preset number to
each detected station.
4 Search will stop after finding appropriate
station and stores as a preset station.
5 Search will start again to find a next station.
You can preset up to 30 of FM stations with Auto Preset.
Any stored station data existing under a preset station number is
cleared when you store a new station under the same preset
station number.
FM TUNING
Automatic tuning
Manual tuning
STANDBY ON
CD iPod
FM
USB
SLEEP
FM
PRESET
FUNCTION
MENU
DISPLAY
FOLDER
SHUFFLE REPEAT
MUTE
VOLUME
TUNING
MEMORY
FM
TUNING
/
Automatic preset tuning
Notes
STANDBY ON
CD iPod
FM
USB
SLEEP
FM
PRESET
FUNCTION
MENU
DISPLAY
FOLDER
SHUFFLE REPEAT
MUTE
VOLUME
TUNING
MEMORY
MEMORY
Center
FM
19 En
FM TUNING
English
TUNER
OPERATIONS
You can also store up to 30 stations manually.
1 Tune into a radio station you want to preset.
See page 18 for tuning instructions.
2 Press MEMORY.
The MEMORY and PRESET indicators light up in
the front panel display until you cancel manual
preset.
To cancel, press MEMORY.
3 Press / repeatedly to select a preset
station number.
4 Press Center while the preset station number
you selected is flashing.
The MEMORY indicator disappears from the front
panel display.
5 Repeat steps 1 to 4 until all desired stations
are preset.
You can tune into any desired station simply by selecting
the preset station under which it was stored (see page 18).
1
Press FM to set the unit to the FM mode.
2 Press PRESET / to select a preset
station.
To delete the preset station
1
Press FM to set the unit to the FM mode.
2 Press FUNCTION to display the function
menu. Press / to select PRESET
DELETE and press Center.
3 Press / to select the preset number
you want to delete and press Center.
Manual preset tuning
STANDBY ON
CD iPod
FM
USB
SLEEP
FM
PRESET
FUNCTION
MENU
DISPLAY
FOLDER
SHUFFLE REPEAT
MUTE
VOLUME
TUNING
MEMORY
MEMORY
Center
/
Selecting preset stations
STANDBY ON
CD iPod
FM
USB
SLEEP
FM
PRESET
FUNCTION
MENU
DISPLAY
FOLDER
SHUFFLE REPEAT
MUTE
VOLUME
TUNING
MEMORY
PRESET /
FM
/
FUNCTION
Center
CONTROLLING iPod™
20 En
In addition to controlling this unit, you can operate your iPod stationed in a terminal using the supplied remote control.
Once you have stationed your iPod in a terminal on the top panel of this unit (see page 12), you can enjoy playback of
your iPod using the supplied remote control. The operations of your iPod are available with the aid of front panel display
(menu browse mode) or without it (simple remote mode).
Only iPod (Click and Wheel), iPod nano, iPod mini, and iPod touch are supported.
Some features may not be compatible depending on the model or the software version of your iPod.
y
For a complete list of the remote control functions used to control your iPod, refer to “iPod mode” (see page 7).
For a complete list of status messages that appear in the front panel display, refer to the “iPod™” section in “TROUBLESHOOTING”
(see page 23).
Simple remote mode
In the simple remote mode, you can operate the iPod menu
by viewing the iPod using the iPod controls or the
supplied remote control.
1 Press iPod to set this unit to the iPod mode.
2 Press FUNCTION and / to show iPod
MODE on the front panel display and press
Center.
3 Press / to select SIMPLE REMOTE.
Press Center while SIMPLE REMOTE is
blinking on the front panel display.
You can also select the menu browse mode by
pressing / so, MENU BROWSE appears
on the front panel display. For details, refer to page
24.
4 Use MENU/ / / Center to operate the
iPod menu, and then press Center to start
playback of the selected song (or group).
CONTROLLING iPod
Using iPod™
Notes
STANDBY ON
CD iPod
FM
USB
SLEEP
FM
PRESET
FUNCTION
MENU
DISPLAY
FOLDER
SHUFFLE REPEAT
MUTE
VOLUME
TUNING
MEMORY
/
MENU
iPod
FUNCTION
Center
21 En
CONTROLLING iPod™
English
OTHER
OPERATIONS
Menu browse mode
In the menu browse mode, you can operate the iPod menu
using the front panel display.
There are some characters that cannot be displayed in the front
panel display of this unit. Those characters are replaced with
underscore “_”.
iPod menu
1 Select the menu browse mode.
To choose the menu browse mode, please refer to
step 3 of "Simple remote mode" in page 20.
The top of the iPod menu appears in the front panel
display.
y
The operation indicators (see page 4) show the operable cursor
keys in each step
.
2 Press / to select the menu, and then
press Center to enter the selected menu.
The name of the first item stored in the selected menu
appears.
y
The Multi information indicators (see page 4) show the iPod
menu currently selected.
To return to the upper level in the iPod menu, press MENU.
3 Repeat step 2 until you select the desired
item, and then press Center to start playback
of the desired item (group or song).
y
While playing back a track (or group) with the menu browse
mode, you can switch the playback information (such as song
name, elapsed time, artist name, or album name) displayed in the
front panel display by pressing DISPLAY
.
Repeating playback (Repeat Play)
You can repeat playback of the selected items in your
iPod.
Press REPEAT to select the desired Repeat Play
mode.
Each time you press the key, the Repeat Play mode
changes as follows. To use properly, please check it with
your iPod.
Playing back randomly (Shuffle Play)
You can play back tracks in your iPod in random order.
Press SHUFFLE.
Each time you press the key, the Shuffle Play mode
changes as follows. To use properly, please check it with
your iPod.
Note
Operation indicators
ARTISTS
One (Repeat play by song)
All (Repeat play by selected group)
Off
Songs (Shuffle play by song)
Albums (Shuffle play by albums)
Off
TROUBLESHOOTING
22 En
Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized
Yamaha dealer or service center.
TROUBLESHOOTING
General
Problem Cause Remedy
See
page
This unit fails to turn
on or enters the
standby mode soon
after the power is
turned on.
The power cable is not connected or the
plug is not completely inserted.
Connect the power cable firmly.
11
This unit has been exposed to a strong
external electric shock (such as lightning
or strong static electricity).
Set this unit to the standby mode, disconnect the
power cable, plug it back in after 30 seconds and
then use it normally.
No sound No appropriate input source has been
selected.
Select an appropriate input source with the INPUT
on the front panel (or the input selection keys on the
remote control).
Speaker connections are not secure. Secure the connections.
9
The volume is turned down. Turn up the volume.
Signals this unit cannot reproduce are
being input from a source component,
such as a CD-ROM.
Play a source whose signals can be reproduced by
this unit.
Sound is heard from
the speaker on one
side only.
Incorrect cable connections. Connect the cables properly. If the problem persists,
the cables may be defective.
9
There is noise
interference from
digital or radio
frequency
equipment.
This unit is too close to the digital or
high-frequency equipment.
Move this unit further away from such equipment.
Radio reception
Problem Cause Remedy
See
page
FM
FM stereo reception is
noisy.
The characteristics of FM stereo
broadcasts may cause this problem
when the transmitter is too far away or
the antenna input is poor.
Check the antenna connections.
11
Try using a high-quality directional FM
antenna.
Use the manual tuning method.
18
There is distortion, and
clear reception cannot
be obtained even with a
good FM antenna.
There is multi-path interference. Adjust the antenna position to eliminate
multi-path interference.
The desired station
cannot be tuned into
with the automatic
tuning method.
The signal is too weak. Use a high-quality directional FM antenna.
Use the manual tuning method.
18
23 En
English
TROUBLESHOOTING
ADDITIONAL
INFORMATION
In case of a transmission error without a status message appearing in the front panel of this unit, check the connection to your iPod (see
page 12).
In case of a transmission error without a status message appearing in the front panel of this unit, check the connection to the USB device
(see page 12).
iPod
Note
Status message Cause Remedy
See
page
iPod Connecting
This unit is in the middle of recognizing
the connection with your iPod.
This unit is in the middle of acquiring
song lists from your iPod.
Connect error
There is a problem with the signal path
from your iPod to this unit.
Turn off this unit and reconnect the iPod.
12
Try resetting your iPod.
Unknown iPod
The iPod being used is not supported by
this unit.
Only iPod (Click and Wheel), iPod nano, iPod mini,
and iPod Touch are supported.
iPod
Your iPod is properly stationed in an
iPod terminal.
iPod Unplugged
Your iPod was removed from an iPod
terminal.
Station your iPod back in an iPod terminal.
12
USB
Note
Status message Cause Remedy
See
page
Not Connected
The USB device is not connected
firmly.
Connect the USB device again.
12
Not Supported
Connected the USB device not playable
on this unit.
Connect playable USB device.
12
Over Current
Connected the USB device not playable
on this unit.
Connected the USB device diagonally.
Disconnect the USB device. Change input source
other than USB and select USB as input source
again. Then connect playable USB device again.
12
24 En
TROUBLESHOOTING
Disc Playback
Problem Cause Remedy
See
page
Power turns on but
immediately shuts
off.
The power cable is not connected or the
plug is not completely inserted.
Connect the power cable firmly.
11
No sound or
distorted sound
The sampling rate of a MP3 or WMA file
may not be compatible with this unit.
Check the sampling rate and bit rate of an MP3 or
WMA file are compatible with this unit.
25
Disc playback does
not start.
You may use a CD-R/RW that is not
finalized.
Finalize the CD-R/RW.
The disc label may not be facing up. Check that the disc label is facing up.
The disc may be defective. Try to play back another disc. If the same problem
does not happen, the disc you want to play back is
defective.
MP3/WMA disc may not contain
sufficient music tracks to be played back.
Check that your MP3/WMA disc contains at least 5
MP3/WMA music files. If the number of files is
small, the disc may not be recognized.
The sampling rate of a MP3 or WMA file
may not be compatible with this unit.
Check the sampling rate and bit rate of an MP3 or
WMA file are compatible with this unit.
25
USB playback does
not start.
Improper USB device connections. Connect the USB device again.
12
The MP3 or WMA formats are not
compatible with this unit.
Replace the file with a correctly recorded file
playable with this unit.
25
Remote control
Problem Cause Remedy
See
page
The remote control
does not work nor
function properly.
The remote control may be operated
outside its operation range.
For information on the remote control operation
range, refer to “Using the remote control”.
8
The remote control sensor on this unit
may be exposed to direct sunlight or
lighting (invented fluorescent lamps).
Change the lighting or orientation of this unit.
The battery may be worn out. Replace the battery with new one.
8
There are obstacles between the sensor of
this unit and the remote control.
Remove the obstacles.
25 En
English
ADDITIONAL
INFORMATION
Discs (audio CDs) playable with this unit
This player is designed for playing back compact discs
bearing the marks shown below. Never attempt to load
any other type of disc into the unit. The unit can also play
back 8-cm (3-inch) compact discs.
About MP3 and WMA files
You can play back MP3 and WMA files recorded on a
CD-R/CD-RW and those stored on a USB device.
MP3
MP3 is a standard technology and format for compressing
an audio sequence into a small-sized file. However, the
original level of sound quality is preserved during
playback.
The playable formats are:
MPEG-1 Audio Layer-3
Bitrate*: 32-320 kbps
Sampling frequency: 44.1/48/32 kHz
MPEG-2 Audio Layer-3, 2
Bitrate*: 8-160 kbps
Sampling frequency: 24/22.05/16 kHz
* Variable bitrate is supported.
WMA
“WMA (Windows Media Audio)” is a Microsoft file
format for encoding digital audio files similar to MP3
though can compress files at a higher rate than MP3.
The playable formats are:
•Version 8
Version 9 (Standard and variable bitrates are
supported. Professional and Lossless are not
supported.)
High Profile
Bitrate*: 32-320 kbps
Sampling frequency: 48/44.1/32 kHz
Mid Profile
Bitrate: 16-32 kbps
Sampling frequency: 22.05/16 kHz
* Both constant and variable bitrates are supported.
Playback for Data Disc starts in alphanumeric order of files.
Playback for USB starts in order by date and time of file
creation.
Copyright-protected WMA (DRM) files cannot be played back
by this unit.
The disc must be ISO9660 compatible.
The maximum file and folder numbers are as follows.
* The root is counted as one of the folders.
NOTES ABOUT DISCS/MP3, WMA FILES
....
Compact discs (digital audio)
The most popular discs for commercially
available audio CDs.
....
CD-R,CD-RW digital audio discs
Music CDs made by copying onto a CD-R
or CD-RW (including MP3 or WMA
format files).
Be sure to use a CD-R or CD-RW disc made
by a reliable manufacture.
Be sure to use a CD-R or CD-RW disc which
has at least one of the following phrases on
the disc or disc case.
FOR CONSUMER
FOR CONSUMER USE
FOR MUSIC USE ONLY
Be sure to use a finalized CD-R or CD-RW
disc.
....
CD-TEXT discs
The discs recorded with text data such as
album titles, track titles and artist names.
This compact disc player may not be able to play back some
CD-RW discs or discs on which recording was not made
correctly.
To prevent a malfunction of this unit:
Do not use any nonstandard
shaped disc (heart, etc.) available
on the market because it might
damage the unit.
Do not use a disc with tape, stickers, or paste on it. If
you use such a disc, the disc may get stuck in the
unit, or damage to the unit may result.
Notes
Note
Notes
Data Disc USB
Maximum total number of file
and folder*
512 9,999
Maximum folder number* 255 255
Maximum file number per
folder
511 255
26 En
NOTES ABOUT DISCS/MP3, WMA FILES
Notes about handling compact discs
Always handle a disc with care so that its surface is not
scratched.
Compact discs are not subjected to wear during
playback, but damage to the disc surface when the disc
is being handled can adversely affect the disc playback.
Be sure to use a felt-tip pen or similar writing tool
when writing on the label side of the disc. Do not use a
ballpoint pen, pencil, or other hard-tipped writing tool,
as these may damage the disc and may adversely affect
the disc playback.
Do not warp discs.
When a disc is not being used, remove it from the unit
and store in an appropriate case.
When removing or storing a disc, be careful not to
scratch the playing surface.
Compact discs are not affected by small particles of
dust or fingerprints on their playing surface, but even
so they should be kept clean. Wipe by using a clean,
dry cloth.
Do not wipe with a circular motion; wipe straight
outward from the center.
Do not try to clean the disc’s surface by using any type
of disc cleaner, record spray, anti-static spray or liquid,
or any other chemical-based liquid because such
substances might irreparably damage the disc’s
surface.
Do not expose discs to direct sunlight, high
temperature or high humidity for a long period of time,
as these might warp or otherwise damage the disc.
To play back an 8-cm (3-inch) CD
Place it in the inner recessed area of the disc tray. Do not
put a normal (12-cm) CD on top of an 8-cm (3-inch) CD.
No!
Note: Do not use any lens cleaners as they may be a
cause of malfunction.
27 En
English
ADDITIONAL
INFORMATION
MP3 (MPEG Audio Layer-3)
One of the audio compression methods used by MPEG. It
employs the irreversible compression method, which
achieves a high compression rate by thinning out the data
of hardly audible part to the human ears. It is said to be
capable of compressing the data quantity by about 1/11
(128 kbps) while maintaining a similar audio quality to
music CD.
PCM (Pulse Code Modulation)
A signal that is changed to digital format without
compression. A CD is recorded with 16-bit sound at
44.1 kHz. This signal also has a type called Packed PCM
(PPCM) that can be compressed without any loss of data.
Sampling frequency
The number of sampling (process for digitalizing analog
signals) per second. In principle, the higher the sampling
rate, the wider the frequency range that can be played
back, and the higher the quantized bit rate, the finer the
sound that can be reproduced.
Track
A CD can be divided into a number of segments (tracks).
Each division is called a track number.
WMA (Windows Media Audio)
An audio compression method developed by Microsoft
Corporation. It employs the irreversible compression
method, which achieves a high compression rate by
thinning out the data of hardly audible part to the human
ears. It is said to be capable of compressing the data
quantity by about 1/22 (64 kbps) while maintaining a
similar audio quality to music CD.
MPEG Layer-3 audio decoding technology licensed from
Fraunhofer IIS and Thomson Multimedia.
PLAYER SECTION
Playback System
•CD, CD-R/RW
Laser
Type ...........................................Semiconductor laser GaAs/GaAlAs
Wave length............................................................................780 nm
Output power..........................................................................10 mW
Audio Performance
DAC............................................................................192 kHz/24 bit
AMPLIFIER SECTION
Maximum RMS output power per channel
(6 Ω , 1 kHz, 10% THD) ...........................................20 W + 20 W
Total harmonic distortion (1 kHz)
CD 10W, 6Ω ........................................................................ 0.03 %
Output level/Impedance
PHONES (volume max) ................................................0.6 V/32 Ω
TUNER SECTION
FM
Tuning Range
[U.S.A and Canada models]..............................87.5 to 107.9 MHz
[Other models] ..............................................87.50 to 108.00 MHz
Sensitivity
FM (S/N 30 dB) ................................................... 7dBμVm (EMF)
GENERAL
Power Supply
[U.S.A. and Canada models]...............................AC 120 V, 60 Hz
[Australia model] ................................................AC 240 V, 50 Hz
[Asia model]............................................AC 220-240 V, 50/60 Hz
[China model]......................................................AC 220 V, 50 Hz
[Korea model] ..................................................... AC 220 V, 60 Hz
[Taiwan model] ............................................AC 110-120 V, 60 Hz
Power consumption................................................................... 25 W
Standby Power consumption*.......................................... 1 W or less
Dimensions (W x H x D) ..................................180 x 117 x 303 mm
(7-
1
/16 x 4-
5
/8 x 11-
15
/16 in)
Weight............................................................... 3.1 kg (6 lbs. 13 oz.)
* When ECO MODE is ON.
Specifications are subject to change without notice.
GLOSSARY
Audio information
Copyright and logo marks
“iPod” is a trademark of Apple Inc., registered in the U.S. and
other countries.
iPod
SPECIFICATIONS
©
2008 Yamaha Corporation All rights reserved.
Printed in Malaysia WQ57120

Transcripción de documentos

UA CD RECEIVER AMPLI-TUNER CD OWNER'S MANUAL MODE D'EMPLOI IMPORTANT SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 1 2 3 4 5 6 7 8 9 • Explanation of Graphical Symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. IMPORTANT Please record the serial number of this unit in the space below. MODEL: Serial No.: The serial number is located on the rear of the unit. Retain this Owner’s Manual in a safe place for future reference. 10 11 12 13 14 Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. We Want You Listening For A Lifetime Yamaha and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often undetectable until it is too late, Yamaha and the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels. i En FCC INFORMATION (for US customers) 1 IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2 IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3 NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/ reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620. The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. DIRECT EXPOSURE TO THE BEAM DANGER: AVOID INVISIBLE LASER RADIATION WHEN OPEN NOT STARE INTO BEAM CAUTION:DO INVISIBLE LASER RADIATION WHEN OPEN ● The label is located on the bottom of the unit. (U.S.A and Canada models only) ii En CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. Install this unit in a well ventilated, cool, dry, clean place with at least 10 cm on the top, 10 cm on the left and right, and 10 cm at the back of this unit — away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds. Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in an environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury. Avoid installing this unit where foreign object may fall onto this unit and/or this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place: – Other components, as they may cause damage and/or discoloration on the surface of this unit. – Burning objects (i.e. candles), as they may cause fire, damage to this unit, and/or personal injury. – Containers with liquid in them, as they may fall and liquid may cause electrical shock to the user and/or damage to this unit. Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury. Do not plug in this unit to a wall outlet until all connections are complete. Do not operate this unit upside-down. It may overheat, possibly causing damage. Do not use force on switches, knobs and/or cords. When disconnecting the power cable from the wall outlet, grasp the plug; do not pull the cable. Do not clean this unit with chemical solvents; this might damage the finish. Use a clean, dry cloth. Only voltage specified on this unit must be used. Using this unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. Yamaha will not be held responsible for any damage resulting from use of this unit with a voltage other than specified. To prevent damage by lightning, keep the power cord and outdoor antennas disconnected from a wall outlet or this unit during a lightning storm. Do not attempt to modify or fix this unit. Contact qualified Yamaha service personnel when any service is needed. The cabinet should never be opened for any reasons. When not planning to use this unit for long periods of time (i.e. vacation), disconnect the AC power plug from the wall outlet. Be sure to read the “TROUBLESHOOTING” section on common operating errors before concluding that this unit is faulty. Before moving this unit, press STANDBY/ON to set this unit to the standby mode, and disconnect the AC power plug from the wall outlet. iii En 18 Condensation will form when the surrounding temperature changes suddenly. Disconnect the power cable from the outlet, then leave this unit alone. 19 When using this unit for a long time, this unit may become warm. Turn the power off, then leave this unit alone for cooling. 20 Install this unit near the AC outlet and where the AC power plug can be reached easily. 21 The batteries shall not be exposed to excessive heat such as sunshine, fire or the like. 22 Excessive sound pressure from earphones and headphones can cause hearing loss. This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off by STANDBY/ON. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power. LASER SAFETY This unit employs a laser. Due to possible eye injury, only a qualified service person should remove the cover or attempt to service this device. DANGER This unit emits visible laser radiation when open. Avoid direct eye exposure to beam. When this unit is plugged into the wall outlet, do not place your eyes close to the opening of the disc tray and other openings to look into inside. The laser component in this product is capable of emitting radiation exceeding the limit for Class 1. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. FOR CANADIAN CUSTOMERS To prevent electric shock, match wide blade of plug to wide slot and fully insert. This Class B digital apparatus complies with Canadian ICES-003. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. CONTENTS FEATURES............................................................. 2 SUPPLIED ACCESSORIES ................................. 2 CONTROLS AND FUNCTIONS ......................... 3 Front panel ................................................................. 3 Front panel display .................................................... 4 Remote control........................................................... 5 OTHER OPERATIONS CONTROLLING iPod™......................................20 Using iPod™ ........................................................... 20 ADDITIONAL INFORMATION INTRODUCTION INTRODUCTION TROUBLESHOOTING .......................................22 CONNECTING SPEAKERS ................................ 9 Connecting a subwoofer .......................................... 10 CONNECTING ANTENNAS.............................. 11 Connecting the FM antenna..................................... 11 CONNECTING THE POWER CABLES .......... 11 CONNECTING HEADPHONES........................ 11 CONNECTING EXTERNAL COMPONENTS ...12 NOTES ABOUT DISCS/MP3, WMA FILES.....25 GLOSSARY...........................................................27 Audio information ................................................... 27 Copyright and logo marks ....................................... 27 SPECIFICATIONS...............................................27 BASIC OPERATIONS BASIC RECEIVER OPERATIONS .................. 13 SETTING THE SLEEP TIMER......................... 14 BASIC PLAYBACK OPERATIONS FOR DISCS AND USB DEVICES........................................ 15 TUNER OPERATIONS Switching the playback information display ........... 16 Repeating playback (Repeat Play)........................... 17 Playing back randomly (Shuffle Play)..................... 17 BASIC OPERATIONS Connecting a USB device........................................ 12 Connecting an iPod™.............................................. 12 General..................................................................... 22 Radio reception........................................................ 22 iPod™ ...................................................................... 23 USB ......................................................................... 23 Disc Playback .......................................................... 24 Remote control ........................................................ 24 PREPARATION PREPARATION TUNER OPERATIONS FM TUNING ......................................................... 18 OTHER OPERATIONS Automatic tuning ..................................................... 18 Manual tuning.......................................................... 18 Automatic preset tuning........................................... 18 Manual preset tuning ............................................... 19 Selecting preset stations........................................... 19 ADDITIONAL INFORMATION English 1 En FEATURES FEATURES • Maximum RMS output power per channel 20W + 20W (10% THD, 1 kHz, 6Ω) • 30-station FM preset tuning • iPod playability • Plays Audio CDs, MP3/WMA discs • CD Text data display • MP3/WMA file playability stored on USB device • Multi function remote control ■ About this manual • This manual describes how to operate this unit using a remote control except when it is not available. Some of these operations are also available using the front panel buttons. • The round shaped button on the center of the remote control is called Center in this manual. • y indicates a tip for your operation. • Notes contain important information about safety and operating instructions. • This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In case of differences between the manual and the product, the product has priority. SUPPLIED ACCESSORIES This product includes the following accessories. Before connecting speakers, make sure you received all of the following parts. Remote control Indoor FM antenna USB cap* Dock cover* STANDBY ON SLEEP CD iPod FM USB PRESET FM TUNING MEMORY (U.S.A and Canada models) FUNCTION MENU DISPLAY FOLDER USB SHUFFLE REPEAT iPod (Other models) MUTE VOLUME When the USB cap and the Dock cover are covered. *The 2 En USB cap and the Dock cover are supplied with this unit to cover the USB port and the iPod terminal when not using. CONTROLS AND FUNCTIONS INTRODUCTION Front panel A B USB IPod Top view 1 2 3 4 VOLUME INPUT STANDBY ON PHONES Front view 5 6 7 8 9 0 1 STANDBY/ON Turns this unit on or sets it to the standby mode. 7 VOLUME Adjusts the volume level. 2 Disc Tray Loads a disc to be played back. 8 INPUT Selects an input source. 3 Front panel display Shows the various information such as the tuning frequency. 9 Stops playback (see page 15). 4 Opens and closes the disc tray. A USB port Connect your USB device (see page 12). English 5 PHONES Outputs audio signals for private listening with headphones. 0 Starts or pauses playback (see page 15). B iPod terminal Connect your iPod (see page 12). 6 Remote control sensor Receives signals from the remote control. 3 En CONTROLS AND FUNCTIONS Front panel display 1 2 3 4 SLEEP PRESET STEREO AUTO TUNED MEMORY 5 6 7 SHUFFLE REPEAT MUTE PLAYLISTS ARTISTS ALBUMS SONGS GENRES B 8 9 0 1 SLEEP indicator Lights up when the sleep timer is on (see page 14). 2 PRESET indicator Lights up when you preset radio stations (see page 19). 3 STEREO indicator Lights up when this unit is receiving a strong signal from an FM stereo broadcast. 4 AUTO indicator Lights up when this unit is in the Automatic Tuning mode (see page 18). 5 SHUFFLE indicator Lights up when you set your iPod/CD/USB in shuffle mode. 6 REPEAT indicator Lights up when you set your iPod/CD/USB in repeat mode. 7 MUTE indicator Lights up when the sound is muted. 4 En A 8 Multi information display Shows the various information such as the tuning frequency. 9 TUNED indicator Lights up when this unit is tuned into a station. 0 MEMORY indicator Lights up when you preset radio stations automatically or manually. A Multi information indicator Light up the menu currently selected (see page 20). B Operation indicators Show operable cursor keys when operating with the FUNCTION or iPod menu with the menu browse mode (see page 20). CONTROLS AND FUNCTIONS Remote control SLEEP CD FM iPod USB PRESET FM TUNING MEMORY Input selection keys FUNCTION MENU To switch the input mode of this unit INTRODUCTION STANDBY ON This remote control can operate the system components and an iPod stationed in a terminal on the top panel of this unit. To operate the CD, USB device, tuner functions, or an iPod using the remote control, you need to set this unit to the corresponding input mode. Press the corresponding input selection key on the remote control (or INPUT on the front panel). The input mode automatically changes to iPod when you connect the iPod during the playback (see page 12). The name of the corresponding input source appears in the front panel display of this unit. ■ Common functions Operations common to all modes 1 2 3 STANDBY ON SLEEP CD 4 FUNCTION 5 DISPLAY iPod FM 7 FM TUNING MEMORY 2 STANDBY/ON Turns this unit on or sets it to the standby mode. 3 Input selection keys Select the input source. MENU 4 FUNCTION By pressing FUNCTION, you can select DIMMER, TREBLE, BASS, BALANCE, or ECO MODE. FOLDER MUTE 1 Infrared signal transmitter Sends signals to the component you want to control. USB PRESET SHUFFLE 6 The following operations are available for this unit when it is set to any input mode. REPEAT VOLUME 8 5 DISPLAY Switches the information shown in the front panel display (see page 16). 6 MUTE Turn off the sound. To restore the sound, press MUTE again or press VOLUME (down)/ (up). 7 SLEEP Sets the sleep timer (see page 14). 8 VOLUME (down) / (up) Adjusts the overall volume level. English 5 En CONTROLS AND FUNCTIONS ■ CD/USB mode Operations available in CD/USB mode The following operations are available for this unit when the CD or USB mode is selected. STANDBY ON SLEEP CD 1 iPod FM 1 , Skips to the beginning of the current track or next track. Press and hold to fast reverse or fast forward (see page 15). Press twice to skip to the beginning of the previous track. USB PRESET FM TUNING MEMORY FUNCTION MENU 2 3 4 DISPLAY FOLDER SHUFFLE MUTE 5 6 7 REPEAT VOLUME 2 DISPLAY Switches the disc/USB information shown in the front panel display (see page 16). 3 FOLDER / Press FOLDER / to playback a first file of selected folder for an MP3 or a WMA folder recorded on disc/USB device (see page 15). *During Shuffle Play, these buttons cannot be used. 4 Starts or pauses playback (see page 15). 5 Stops playback (see page 15). 6 REPEAT Selects the Repeat Play mode (see page 17). 7 SHUFFLE Select the Shuffle Play feature (see page 17). ■ FM mode Operations available in FM mode The following operations are available for this unit when the FM mode is selected. STANDBY ON SLEEP CD iPod FM FM PRESET 1 USB MEMORY TUNING 2 3 FUNCTION MENU 4 DISPLAY FOLDER SHUFFLE 1 TUNING Press TUNING hold TUNING / 2 PRESET Press PRESET page 18). / / / to Manual tuning and press and to Automatic tuning. / to select a preset station (see 3 MEMORY Starts preset memory mode. REPEAT 4 Center Press Center to fix the current setting. MUTE 6 En VOLUME CONTROLS AND FUNCTIONS ■ iPod mode Operations available in iPod mode SLEEP CD 1 2 3 4 5 6 iPod FM USB PRESET FM TUNING MEMORY FUNCTION 7 8 MENU 9 DISPLAY FOLDER SHUFFLE MUTE REPEAT 0 VOLUME 1 FUNCTION Switches between the simple remote mode and menu browse mode. 2 Center Press Center to enter the selected group. (Pressing Center starts playback when a song is selected.) INTRODUCTION The following operations are available for the iPod stationed in the terminal. For details on iPod operations, see “Using iPod™” on page 20. STANDBY ON 3 Skips to the beginning of the current track. Press and hold to fast reverse. Press twice to skip to the previous track. 4 DISPLAY Displays the song information while iPod is in menu browse mode (see page 16). 5 Starts or pauses playback. 6 SHUFFLE Selects the shuffle playback mode (see page 21). iPod Remote Control 7 MENU Returns to the upper level in the iPod menu. 8 Skips to the next track. Press and hold to fast forward. 9 Press / or to select an item in the selected group. 0 REPEAT Selects the repeat playback mode (see page 21). The supplied remote control has the same function keys with your iPod. So, these keys are corresponding with each other. English 7 En CONTROLS AND FUNCTIONS ■ Preparing the remote control ■ Using the remote control The remote control comes with the battery already installed. Before using the remote control for the very first time, pull out the insulation sheet, as shown. Use the remote control within 6 m (20 feet) of the component you want to control and point it toward its remote control sensor (see page 3). Insulation sheet VOLUME INPUT STANDBY ON PHONES Within 6 m (20 feet) 30˚ y 30˚ STANDBY ON SLEEP CD iPod FM USB FM PRESET Remove the transparent sheet before using the remote control. MEMORY TUNING FUNCTION MENU DISPLAY FOLDER SHUFFLE MUTE REPEAT VOLUME Notes • Be careful not to spill liquid on the remote control. • Be careful not to drop the remote control. • Do not leave the remote control in the following places: – hot or humid places, such as near a heater or in a bathroom – extremely cold places – dusty places ■ Replacing the battery in the remote control Change the battery when the operation range of the remote control decreases. Use a straight pin to remove the cover. Replace the battery with a new CR2025 battery. Close the cover. Notes • • • • • Insert the battery according to the polarity markings (+ and -). If the battery runs out, immediately remove it from the remote control to prevent an explosion or acid leak. If the battery starts leaking, dispose of it immediately. Be careful not to let the leaking battery acid touch your skin or clothing. Before inserting a new battery, wipe the compartment clean. Dispose of batteries according to your regional regulations. 8 En CONNECTING SPEAKERS CONNECTING SPEAKERS Follow the procedure below to connect speakers to this unit. For information on your speakers, refer to the owner’s manual supplied for the speakers. CAUTION Do not connect the power cable of this unit until all cable connections are completed. Notes Right speaker PREPARATION • Be sure to connect the left channel (L), right channel (R), “+”(red) “–”(black) properly. If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lacks bass. • Do not let the bare speaker wires touch each other or do not let them touch any metal part of this unit. This could damage this unit and/ or the speakers. • Use speakers with the specified impedance shown on the rear panel of this unit. Left speaker Speaker cables MAINS TUNER SPEAKERS FM ANT 75 UNBAL R L SUBWOOFER OUT Rear panel English 9 En CONNECTING SPEAKERS 1 Remove approximately 10 mm (3/8 in) of insulation from the end of each speaker cable and then twist the exposed wires of the cable together to prevent short circuits. Connecting a subwoofer The low frequency range of the left channel and the right channel are mixed to output at the SUBWOOFER OUT jack. Connect the SUBWOOFER OUT jack on this unit to the INPUT jack on the subwoofer using the subwoofer cable (commercially available). 10 mm (3/8 in) TUN SUBWOOFER OUT 2 Press and hold the lever. Subwoofer cable (commercially available) Red: positive (+) Black: negative (–) INPUT INPUT 3 Insert one bare wire. By releasing the lever, the lever is replaced. Subwoofer (commercially available) Red: positive (+) Black: negative (–) Note Do not connect the power cable of this unit and the subwoofer until all cable connections are completed. ■ Notes on the speaker cord A speaker cord is actually a pair of insulated cables running side by side. One cable is colored or shaped differently, perhaps with a stripe, groove or ridge. Connect the striped (grooved, etc.) cable to the “+”(red) terminals on this unit and your speaker. Connect the plain cable to the “–”(black) terminals on this unit and your speaker. 10 En CONNECTING ANTENNAS CONNECTING ANTENNAS To enjoy radio on this unit, connect the supplied FM antenna to the designated terminals. If there is a problem of weak radio wave reception in your area or you want to improve radio reception, we recommend that you use commercially available outdoor antennas. For details, consult the nearest authorized Yamaha dealer or service center. Indoor FM antenna (supplied) Connecting the FM antenna 1 Connect the supplied indoor FM antenna to the FM jack of this unit. 2 Place the antenna away from this unit and speaker cables. FM ANT 75 UNBAL SUBWOOFER OUT PREPARATION TUNER CONNECTING THE POWER CABLES After you made all connections, connect the power cables of this unit and subwoofer (optional). MAINS TUNER SPEAKERS FM ANT 75 UNBAL To an AC wall outlet R L SUBWOOFER OUT 6 MIN. SPEAKER CONNECTING HEADPHONES You can connect your headphones to the PHONES jack on the front panel of this unit. The sound from the speakers stops. VOLUME INPUT STANDBY ON PHONES English 11 En CONNECTING EXTERNAL COMPONENTS CONNECTING EXTERNAL COMPONENTS You can connect a USB device or an iPod to this unit. For information on your component, refer to the owner's manual supplied with the component. Connecting a USB device This unit has a USB port and can access MP3 or WMA files saved on your USB device. Connect your USB device to the USB port on the top panel of this unit. For playback information of a USB device, see page 15. USB device Connecting an iPod™ This unit equips the iPod terminal on the top panel where you can directly station your iPod and control playback of your iPod using the supplied remote control. Use this unit with the iPod dock adapter (supplied with your iPod or commercially available) appropriate for your iPod. If you use this unit without using an appropriate iPod dock adapter, loose connection may result. iPod USB iPod USB iPod VOLUME INPUT STANDBY ON PHONES ■ Supported USB devices This unit supports USB mass storage class devices (e.g., flash memories) using FAT16 or FAT32 format. Notes • Some devices may not work properly even if they meet the requirements. • If your USB device is not played back after you connected it to this unit, follow any of the procedures below. – Set this unit to the standby mode, and turn it on again. – Disconnect the device while this unit is in the standby mode. – Then connect the device again and turn on this unit. – Connect an AC adapter if supplied with the device. • If the USB device is not played back even after you performed the procedure(s) above, the device may not be playable on this unit. • Do not connect devices other than USB mass storages class devices. • Yamaha and suppliers accept no liability for the loss of data saved on the USB devices connected to this unit. As a precaution, it is recommended that the files are made backup copies. • Playability of and power supply to all kind of USB devices are not guaranteed. • Your USB device is automatically charged when your USB device is connected to the USB port even when this unit is in standby mode and ECO MODE is OFF. • To remove USB device safely, disconnect after the playback is stopped. 12 En VOLUME INPUT STANDBY ON PHONES Notes • Only iPod (Click and Wheel), iPod nano, iPod mini, and iPod touch are supported. • Do not connect any iPod accessories (such as headphones, a wired remote control, or an FM transmitter) to our iPod when it is stationed in the terminal. • Unless your iPod is firmly stationed in the terminal, audio signals may not be output properly. • Once the connection between your iPod and this unit is complete, “iPod” appears in the front panel display. If the connection between your iPod and this unit fails, a status message appears in the front panel display. For a complete list of connection status message, see the iPod section in “TROUBLESHOOTING” on page 23. • Your iPod is automatically charged when your iPod is stationed in the terminal even when this unit is in standby mode and ECO MODE is OFF. • To remove iPod safely, disconnect after the playback is stopped. BASIC RECEIVER OPERATIONS BASIC RECEIVER OPERATIONS Follow the procedure below to select an input source and adjust the sound settings on this unit. 4 Press (down) / (up) to adjust the volume to the desired output level. ■ To adjust the audio quality VOLUME Press FUNCTION to display the function menu. STANDBY ON 2 Press / repeatedly to select TREBLE, BASS, or BALANCE and press Center. 3 Press / repeatedly to adjust the setting and press Center. PHONES STANDBY/ON STANDBY/ON Input selection keys VOLUME INPUT TREBLE: Adjusts the high frequency response. BASS: Adjusts the low frequency response. BALANCE: Adjusts the volume level of each left and right speaker channel. STANDBY ON SLEEP CD iPod FM USB PRESET FM TUNING MEMORY y TREBLE, BASS, and BALANCE are not adjustable when using the headphones. FUNCTION FUNCTION BASIC OPERATIONS 1 INPUT MENU / Center ■ To dim the display DISPLAY FOLDER SHUFFLE MUTE 1 2 3 You can dim the front panel display of this unit. REPEAT VOLUME VOLUME / Press STANDBY/ON to turn on this unit. The front panel display lights up. Press one of the input selection keys or press INPUT on the front panel to select the desired input source. Each time you press INPUT, the input source changes in order of CD, iPod, FM and USB. Press FUNCTION to display the function menu. 2 Press / repeatedly to select DIMMER and press Center. Press / to select the brightness and press Center. ■ To use the ECO mode This mode reduces power consumption during the standby mode. Your iPod or USB device cannot be charged during standby mode and ECO MODE is ON. 1 Press FUNCTION to display the function menu. 2 Press / repeatedly to select ECO MODE and press Center. 3 Press Center. / to select ON or OFF and press 13 En English Start playback on the selected source component or select a radio station. For information on the disc playback, see page 15, and for information on tuning, see page 18. 1 SETTING THE SLEEP TIMER SETTING THE SLEEP TIMER The sleep timer sets this unit to the standby mode after the specified time elapses. STANDBY ON SLEEP CD iPod FM SLEEP USB PRESET FM TUNING MEMORY FUNCTION MENU DISPLAY FOLDER SHUFFLE MUTE REPEAT VOLUME Press SLEEP repeatedly to select the desired duration. Each time you press the key, the duration changes as follows. The SLEEP indicator lights up in the front panel display. SLEEP 30min SLEEP 60min SLEEP 90min SLEEP 120min SLEEP OFF y • The sleep timer is canceled if you set this unit to the standby mode. • If you press SLEEP while the sleep timer is set, the remaining time appears in the front panel display. To cancel the sleep timer Press SLEEP repeatedly to select “SLEEP OFF”. 14 En BASIC PLAYBACK OPERATIONS FOR DISCS AND USB DEVICES BASIC PLAYBACK OPERATIONS FOR DISCS AND USB DEVICES You can enjoy playback your audio CDs, USB devices, and MP3 or WMA files recorded on a disc/USB device. Some operations may be different or restricted depending on the disc/USB device. Before playing back, check the compatibility of your disc/USB device with this unit (see page 25). STANDBY ON SLEEP CD / iPod FM USB PRESET FM TUNING MEMORY • Some files may not work properly depending on the USB device specification. • Copyright-protected files cannot be played back. • This unit can play back files of 4 GB in size or less. • When the input source is USB and this unit is turned on with the USB device connected, playback starts automatically. To stop playback FUNCTION MENU Press DISPLAY FOLDER FOLDER / SHUFFLE To pause playback REPEAT VOLUME Press . To return to normal playback, press BASIC OPERATIONS MUTE . . To fast reverse or fast forward To start disc playback 1 Select CD as the input source (see page 13). 2 Press while a disc is loaded. For an audio CD, playback starts from the first track, and for MP3 or WMA files, playback starts in alphanumeric order by the filename. y • You can open and close the disc tray by pressing on the front panel of this unit. • You can also start disc playback by pressing on the front panel. • When the input source is CD and this unit is turned on with a disc loaded, disc playback starts automatically. To fast reverse, hold down To fast forward, hold down . . To skip tracks To skip to the start of the current track, press To skip to the next track, press . To skip to the previous track, quickly press . twice. To skip a folder for an MP3 or WMA file To skip a folder, press FOLDER / . ■ About MP3 and WMA discs/USB device Root To start USB device playback Folder 1 Select USB as the input source (see page 13). File 2 Connect your USB device to the USB port on this unit. The reading time may exceed 30 seconds depending on the number of files/folders. For a USB device, playback starts automatically in order by the date and time of creation if playable files are in the USB device. You can play back MP3 or WMA files recorded on your CD-R, CD-RW or USB device. This unit regards files in the disc/USB device as tracks (as shown above). Notes English • Total time does not appear on the front panel for USB device playback. • If the USB device is partitioned, only the first partition is displayed. 15 En BASIC PLAYBACK OPERATIONS FOR DISCS AND USB DEVICES Switching the playback information display You can switch the disc playback information shown in the front panel display of this unit. Available information differs depending on the type of the disc/USB device. FM Press DISPLAY repeatedly while playing back a disc/USB device. Each time you press the key, the information display changes as described in “Playback information for audio CDs” and “Playback information for MP3 or WMA files recorded on discs/USB devices” on page 16. DISPLAY PRESET TUNING MEMORY FUNCTION MENU DISPLAY FOLDER SHUFFLE Note REPEAT Some special characters may not be shown properly. ■ Playback information for audio CDs The following information is available during playback of an audio CD. “Track Title”, “Artist”, and “Album Title” are available only for a CD TEXT disc. 7 Album Title 1 Elapsed time of the current track (Default) ALBUMS 2 Remaining time of the current track 6 Artist ARTISTS 3 Total time of the disc 5 Track Title 4 Remaining time of the disc SONGS Note You can switch the playback information 1 2 5 6 7 above during playback of your iPod in the menu browse mode (see page 21). ■ Playback information for MP3 or WMA files recorded on discs/USB devices The following information is available during playback of an MP3 or WMA files recorded on discs/USB device. 1 Elapsed time of the current file 5 Album Title ALBUMS 4 Artist 2 File Name ARTISTS 3 Track Title SONGS 16 En BASIC PLAYBACK OPERATIONS FOR DISCS AND USB DEVICES Repeating playback (Repeat Play) Playing back randomly (Shuffle Play) You can repeat the playback of the selected item in your disc/USB device. You can play back tracks in your disc/USB device in random order. Note STANDBY ON When playing back with Shuffle Play, the remaining time of the disc cannot be displayed. SLEEP CD iPod FM USB PRESET FM TUNING MEMORY STANDBY ON SLEEP FUNCTION MENU CD iPod FM USB PRESET FM TUNING MEMORY DISPLAY FOLDER SHUFFLE REPEAT FUNCTION REPEAT DISPLAY VOLUME BASIC OPERATIONS MUTE MENU FOLDER SHUFFLE REPEAT SHUFFLE MUTE 1 Play back the disc or track you want to repeat. 2 Press REPEAT to select the desired Repeat Play mode. Each time you press the key, the Repeat Play mode in the front panel display changes as follows. VOLUME Press SHUFFLE. Each time you press the key, the Shuffle play mode in the front panel display changes as follows. Audio CD Audio CD REPEAT ONE (Repeat Play by track) REPEAT ALL (Repeat Play by disc) Off (Normal playback) MP3/WMA disc/USB device REPEAT ONE (Repeat Play by track) REPEAT FOLDER (Repeat Play in the folder) REPEAT ALL (Repeat Play by disc) SHUFFLE ALL Off MP3/WMA disc/USB device SHUFFLE FOLDER* SHUFFLE ALL Off * The SHUFFLE FOLDER means tracks in the folder is play back in randomly. Off (Normal playback) To cancel Shuffle Play Press REPEAT repeatedly so that the Repeat Play mode indicator disappears from the front panel display or press . Press SHUFFLE repeatedly so that the SHUFFLE indicator disappears from the front panel display or press . 17 En English To cancel Repeat Play FM TUNING FM TUNING There are 2 tuning methods: automatic and manual. Automatic tuning is effective when station signals are strong and there is no interference. If the signal from the station you want to select is weak, tune into it manually. You can also use the automatic and manual preset tuning features to store up to 30 stations. Automatic tuning Automatic preset tuning Automatic tuning is effective when station signals are strong and there is no interference. Follow the procedure below to preset radio stations automatically. STANDBY ON STANDBY ON SLEEP SLEEP CD iPod FM USB FM CD FM USB FM FM PRESET TUNING / iPod PRESET FM TUNING MEMORY MEMORY TUNING MEMORY FUNCTION FUNCTION MENU MENU Center DISPLAY DISPLAY FOLDER FOLDER SHUFFLE REPEAT SHUFFLE MUTE REPEAT VOLUME MUTE VOLUME 1 Press FM to set this unit to the FM mode. 1 Press FM to set the unit to the FM mode. 2 Press and hold TUNING / to begin automatic tuning. The AUTO indicator lights up on the front panel display. This unit automatically detects radio stations that have strong signals for your selection, and automatically ends automatic tuning. The AUTO indicator disappears from the front panel display. 2 Press and hold MEMORY for more than 2 seconds. The “AUTO PRESET” and “Push Center Key” appear in the front panel display alternately. To cancel, press MEMORY. 3 Press Center to start searching automatically. • Auto Preset starts at the lowest frequency toward the highest frequency. • This unit automatically applies a preset number to each detected station. 4 Search will stop after finding appropriate station and stores as a preset station. 5 Search will start again to find a next station. Manual tuning If the signal received from the station you want to select is weak, tune into it manually. 1 Press FM to set this unit to the FM mode. 2 Press TUNING / repeatedly to tune into the desired station manually. y Manually tuning into an FM station automatically switches the tuner to monaural reception to increase the signal quality. 18 En Notes • You can preset up to 30 of FM stations with Auto Preset. • Any stored station data existing under a preset station number is cleared when you store a new station under the same preset station number. FM TUNING Manual preset tuning Selecting preset stations You can tune into any desired station simply by selecting the preset station under which it was stored (see page 18). You can also store up to 30 stations manually. STANDBY ON SLEEP STANDBY ON SLEEP CD iPod FM USB CD USB FM PRESET FM PRESET TUNING MEMORY iPod FM FM PRESET MEMORY TUNING MEMORY / FUNCTION MENU FUNCTION / Center FUNCTION MENU DISPLAY Center FOLDER / DISPLAY FOLDER SHUFFLE REPEAT SHUFFLE MUTE VOLUME VOLUME MUTE Tune into a radio station you want to preset. See page 18 for tuning instructions. 2 Press MEMORY. The MEMORY and PRESET indicators light up in the front panel display until you cancel manual preset. To cancel, press MEMORY. 3 Press / repeatedly to select a preset station number. 4 Press Center while the preset station number you selected is flashing. The MEMORY indicator disappears from the front panel display. 1 Press FM to set the unit to the FM mode. 2 Press PRESET station. / to select a preset TUNER OPERATIONS 1 5 REPEAT ■ To delete the preset station 1 Press FM to set the unit to the FM mode. 2 Press FUNCTION to display the function menu. Press / to select PRESET DELETE and press Center. 3 Press / to select the preset number you want to delete and press Center. Repeat steps 1 to 4 until all desired stations are preset. English 19 En CONTROLLING iPod™ CONTROLLING iPod™ In addition to controlling this unit, you can operate your iPod stationed in a terminal using the supplied remote control. Using iPod™ Once you have stationed your iPod in a terminal on the top panel of this unit (see page 12), you can enjoy playback of your iPod using the supplied remote control. The operations of your iPod are available with the aid of front panel display (menu browse mode) or without it (simple remote mode). Notes • Only iPod (Click and Wheel), iPod nano, iPod mini, and iPod touch are supported. • Some features may not be compatible depending on the model or the software version of your iPod. y • For a complete list of the remote control functions used to control your iPod, refer to “iPod mode” (see page 7). • For a complete list of status messages that appear in the front panel display, refer to the “iPod™” section in “TROUBLESHOOTING” (see page 23). ■ Simple remote mode In the simple remote mode, you can operate the iPod menu by viewing the iPod using the iPod controls or the supplied remote control. STANDBY ON SLEEP iPod CD iPod FM USB PRESET FM TUNING MEMORY MENU 1 Press iPod to set this unit to the iPod mode. 2 Press FUNCTION and / to show iPod MODE on the front panel display and press Center. 3 Press / to select SIMPLE REMOTE. Press Center while SIMPLE REMOTE is blinking on the front panel display. • You can also select the menu browse mode by pressing / so, MENU BROWSE appears on the front panel display. For details, refer to page 24. 4 Use MENU/ / / Center to operate the iPod menu, and then press Center to start playback of the selected song (or group). FUNCTION FUNCTION Center MENU / DISPLAY FOLDER SHUFFLE MUTE 20 En REPEAT VOLUME CONTROLLING iPod™ ■ Menu browse mode In the menu browse mode, you can operate the iPod menu using the front panel display. 3 Note There are some characters that cannot be displayed in the front panel display of this unit. Those characters are replaced with underscore “_”. iPod menu Repeat step 2 until you select the desired item, and then press Center to start playback of the desired item (group or song). y While playing back a track (or group) with the menu browse mode, you can switch the playback information (such as song name, elapsed time, artist name, or album name) displayed in the front panel display by pressing DISPLAY. ■ Repeating playback (Repeat Play) You can repeat playback of the selected items in your iPod. Press REPEAT to select the desired Repeat Play mode. Each time you press the key, the Repeat Play mode changes as follows. To use properly, please check it with your iPod. 1 Select the menu browse mode. To choose the menu browse mode, please refer to step 3 of "Simple remote mode" in page 20. The top of the iPod menu appears in the front panel display. One (Repeat play by song) All (Repeat play by selected group) Off ■ Playing back randomly (Shuffle Play) You can play back tracks in your iPod in random order. Operation indicators y The operation indicators (see page 4) show the operable cursor keys in each step. Press / to select the menu, and then press Center to enter the selected menu. The name of the first item stored in the selected menu appears. Songs (Shuffle play by song) OTHER OPERATIONS 2 Press SHUFFLE. Each time you press the key, the Shuffle Play mode changes as follows. To use properly, please check it with your iPod. Albums (Shuffle play by albums) Off ARTISTS y English • The Multi information indicators (see page 4) show the iPod menu currently selected. • To return to the upper level in the iPod menu, press MENU. 21 En TROUBLESHOOTING TROUBLESHOOTING Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center. General Problem This unit fails to turn on or enters the standby mode soon after the power is turned on. Cause Remedy See page The power cable is not connected or the plug is not completely inserted. Connect the power cable firmly. 11 This unit has been exposed to a strong external electric shock (such as lightning or strong static electricity). Set this unit to the standby mode, disconnect the power cable, plug it back in after 30 seconds and then use it normally. — No appropriate input source has been selected. Select an appropriate input source with the INPUT on the front panel (or the input selection keys on the remote control). — Speaker connections are not secure. Secure the connections. 9 The volume is turned down. Turn up the volume. — Signals this unit cannot reproduce are being input from a source component, such as a CD-ROM. Play a source whose signals can be reproduced by this unit. — Sound is heard from the speaker on one side only. Incorrect cable connections. Connect the cables properly. If the problem persists, the cables may be defective. 9 There is noise interference from digital or radio frequency equipment. This unit is too close to the digital or high-frequency equipment. Move this unit further away from such equipment. — No sound Radio reception Problem FM stereo reception is noisy. FM 22 En Cause The characteristics of FM stereo broadcasts may cause this problem when the transmitter is too far away or the antenna input is poor. Remedy See page Check the antenna connections. 11 Try using a high-quality directional FM antenna. — Use the manual tuning method. 18 There is distortion, and clear reception cannot be obtained even with a good FM antenna. There is multi-path interference. Adjust the antenna position to eliminate multi-path interference. — The desired station cannot be tuned into with the automatic tuning method. The signal is too weak. Use a high-quality directional FM antenna. — Use the manual tuning method. 18 TROUBLESHOOTING iPod™ Note In case of a transmission error without a status message appearing in the front panel of this unit, check the connection to your iPod (see page 12). Status message Cause iPod Connecting This unit is in the middle of recognizing the connection with your iPod. Remedy See page This unit is in the middle of acquiring song lists from your iPod. Connect error There is a problem with the signal path from your iPod to this unit. Unknown iPod The iPod being used is not supported by this unit. iPod Your iPod is properly stationed in an iPod terminal. iPod Unplugged Your iPod was removed from an iPod terminal. Turn off this unit and reconnect the iPod. 12 Try resetting your iPod. — Only iPod (Click and Wheel), iPod nano, iPod mini, and iPod Touch are supported. — Station your iPod back in an iPod terminal. 12 USB Note In case of a transmission error without a status message appearing in the front panel of this unit, check the connection to the USB device (see page 12). Status message Cause Remedy See page Not Connected The USB device is not connected firmly. Connect the USB device again. 12 Not Supported Connected the USB device not playable on this unit. Connect playable USB device. 12 Over Current Connected the USB device not playable on this unit. Connected the USB device diagonally. Disconnect the USB device. Change input source other than USB and select USB as input source again. Then connect playable USB device again. 12 ADDITIONAL INFORMATION English 23 En TROUBLESHOOTING Disc Playback Problem Cause Remedy See page Power turns on but immediately shuts off. The power cable is not connected or the plug is not completely inserted. Connect the power cable firmly. 11 No sound or distorted sound The sampling rate of a MP3 or WMA file may not be compatible with this unit. Check the sampling rate and bit rate of an MP3 or WMA file are compatible with this unit. 25 Disc playback does not start. You may use a CD-R/RW that is not finalized. Finalize the CD-R/RW. — The disc label may not be facing up. Check that the disc label is facing up. — The disc may be defective. Try to play back another disc. If the same problem does not happen, the disc you want to play back is defective. — MP3/WMA disc may not contain sufficient music tracks to be played back. Check that your MP3/WMA disc contains at least 5 MP3/WMA music files. If the number of files is small, the disc may not be recognized. — The sampling rate of a MP3 or WMA file may not be compatible with this unit. Check the sampling rate and bit rate of an MP3 or WMA file are compatible with this unit. 25 Improper USB device connections. Connect the USB device again. 12 The MP3 or WMA formats are not compatible with this unit. Replace the file with a correctly recorded file playable with this unit. 25 USB playback does not start. Remote control Problem The remote control does not work nor function properly. 24 En Cause Remedy See page The remote control may be operated outside its operation range. For information on the remote control operation range, refer to “Using the remote control”. 8 The remote control sensor on this unit may be exposed to direct sunlight or lighting (invented fluorescent lamps). Change the lighting or orientation of this unit. — The battery may be worn out. Replace the battery with new one. 8 There are obstacles between the sensor of this unit and the remote control. Remove the obstacles. — NOTES ABOUT DISCS/MP3, WMA FILES ■ Discs (audio CDs) playable with this unit MP3 This player is designed for playing back compact discs bearing the marks shown below. Never attempt to load any other type of disc into the unit. The unit can also play back 8-cm (3-inch) compact discs. MP3 is a standard technology and format for compressing an audio sequence into a small-sized file. However, the original level of sound quality is preserved during playback. The playable formats are: • MPEG-1 Audio Layer-3 Bitrate*: 32-320 kbps Sampling frequency: 44.1/48/32 kHz • MPEG-2 Audio Layer-3, 2 Bitrate*: 8-160 kbps Sampling frequency: 24/22.05/16 kHz * Variable bitrate is supported. .... Compact discs (digital audio) The most popular discs for commercially available audio CDs. .... CD-R,CD-RW digital audio discs Music CDs made by copying onto a CD-R or CD-RW (including MP3 or WMA format files). Notes • Be sure to use a CD-R or CD-RW disc made by a reliable manufacture. • Be sure to use a CD-R or CD-RW disc which has at least one of the following phrases on the disc or disc case. FOR CONSUMER FOR CONSUMER USE FOR MUSIC USE ONLY • Be sure to use a finalized CD-R or CD-RW disc. .... CD-TEXT discs The discs recorded with text data such as album titles, track titles and artist names. Note This compact disc player may not be able to play back some CD-RW discs or discs on which recording was not made correctly. To prevent a malfunction of this unit: • Do not use any nonstandard shaped disc (heart, etc.) available on the market because it might damage the unit. ■ About MP3 and WMA files You can play back MP3 and WMA files recorded on a CD-R/CD-RW and those stored on a USB device. “WMA (Windows Media Audio)” is a Microsoft file format for encoding digital audio files similar to MP3 though can compress files at a higher rate than MP3. The playable formats are: • Version 8 • Version 9 (Standard and variable bitrates are supported. Professional and Lossless are not supported.) • High Profile Bitrate*: 32-320 kbps Sampling frequency: 48/44.1/32 kHz • Mid Profile Bitrate: 16-32 kbps Sampling frequency: 22.05/16 kHz * Both constant and variable bitrates are supported. Notes • Playback for Data Disc starts in alphanumeric order of files. • Playback for USB starts in order by date and time of file creation. • Copyright-protected WMA (DRM) files cannot be played back by this unit. • The disc must be ISO9660 compatible. • The maximum file and folder numbers are as follows. Data Disc USB Maximum total number of file and folder* 512 9,999 Maximum folder number* 255 255 Maximum file number per folder 511 255 ADDITIONAL INFORMATION • Do not use a disc with tape, stickers, or paste on it. If you use such a disc, the disc may get stuck in the unit, or damage to the unit may result. WMA * The root is counted as one of the folders. English 25 En NOTES ABOUT DISCS/MP3, WMA FILES ■ Notes about handling compact discs To play back an 8-cm (3-inch) CD • Always handle a disc with care so that its surface is not scratched. Place it in the inner recessed area of the disc tray. Do not put a normal (12-cm) CD on top of an 8-cm (3-inch) CD. Note: Do not use any lens cleaners as they may be a cause of malfunction. • Compact discs are not subjected to wear during playback, but damage to the disc surface when the disc is being handled can adversely affect the disc playback. • Be sure to use a felt-tip pen or similar writing tool when writing on the label side of the disc. Do not use a ballpoint pen, pencil, or other hard-tipped writing tool, as these may damage the disc and may adversely affect the disc playback. • Do not warp discs. • When a disc is not being used, remove it from the unit and store in an appropriate case. • When removing or storing a disc, be careful not to scratch the playing surface. • Compact discs are not affected by small particles of dust or fingerprints on their playing surface, but even so they should be kept clean. Wipe by using a clean, dry cloth. Do not wipe with a circular motion; wipe straight outward from the center. • Do not try to clean the disc’s surface by using any type of disc cleaner, record spray, anti-static spray or liquid, or any other chemical-based liquid because such substances might irreparably damage the disc’s surface. • Do not expose discs to direct sunlight, high temperature or high humidity for a long period of time, as these might warp or otherwise damage the disc. No! 26 En GLOSSARY ■ Track Audio information A CD can be divided into a number of segments (tracks). Each division is called a track number. ■ MP3 (MPEG Audio Layer-3) One of the audio compression methods used by MPEG. It employs the irreversible compression method, which achieves a high compression rate by thinning out the data of hardly audible part to the human ears. It is said to be capable of compressing the data quantity by about 1/11 (128 kbps) while maintaining a similar audio quality to music CD. ■ PCM (Pulse Code Modulation) ■ WMA (Windows Media Audio) An audio compression method developed by Microsoft Corporation. It employs the irreversible compression method, which achieves a high compression rate by thinning out the data of hardly audible part to the human ears. It is said to be capable of compressing the data quantity by about 1/22 (64 kbps) while maintaining a similar audio quality to music CD. Copyright and logo marks A signal that is changed to digital format without compression. A CD is recorded with 16-bit sound at 44.1 kHz. This signal also has a type called Packed PCM (PPCM) that can be compressed without any loss of data. MPEG Layer-3 audio decoding technology licensed from Fraunhofer IIS and Thomson Multimedia. ■ Sampling frequency iPod™ The number of sampling (process for digitalizing analog signals) per second. In principle, the higher the sampling rate, the wider the frequency range that can be played back, and the higher the quantized bit rate, the finer the sound that can be reproduced. “iPod” is a trademark of Apple Inc., registered in the U.S. and other countries. SPECIFICATIONS ■ PLAYER SECTION ■ TUNER SECTION Playback System FM • CD, CD-R/RW Laser • Type ...........................................Semiconductor laser GaAs/GaAlAs • Wave length............................................................................780 nm • Output power ..........................................................................10 mW Audio Performance • DAC............................................................................192 kHz/24 bit ■ AMPLIFIER SECTION ■ GENERAL • Power Supply [U.S.A. and Canada models]............................... AC 120 V, 60 Hz [Australia model] ................................................ AC 240 V, 50 Hz [Asia model]............................................AC 220-240 V, 50/60 Hz [China model]...................................................... AC 220 V, 50 Hz [Korea model] ..................................................... AC 220 V, 60 Hz [Taiwan model] ............................................AC 110-120 V, 60 Hz • Power consumption................................................................... 25 W • Standby Power consumption*.......................................... 1 W or less • Dimensions (W x H x D) .................................. 180 x 117 x 303 mm (7-1/16 x 4-5/8 x 11-15/16 in) • Weight ............................................................... 3.1 kg (6 lbs. 13 oz.) * When ECO MODE is ON. ADDITIONAL INFORMATION • Maximum RMS output power per channel (6 Ω , 1 kHz, 10% THD) ...........................................20 W + 20 W • Total harmonic distortion (1 kHz) CD 10W, 6Ω ........................................................................ 0.03 % • Output level/Impedance PHONES (volume max) ................................................0.6 V/32 Ω • Tuning Range [U.S.A and Canada models]..............................87.5 to 107.9 MHz [Other models] .............................................. 87.50 to 108.00 MHz • Sensitivity FM (S/N 30 dB) ................................................... 7dBμVm (EMF) Specifications are subject to change without notice. English 27 En © 2008 Yamaha Corporation All rights reserved. Printed in Malaysia WQ57120
1 / 1

Yamaha CRX-330 Manual de usuario

Categoría
Receptores AV
Tipo
Manual de usuario