Yamaha PM5D-RH El manual del propietario

Marca: Yamaha

Modelo: PM5D-RH

Categoría: Mezcladores de audio

Tipo: El manual del propietario

Este manual también es adecuado para

PM5D
V2

PM5D/PM5D-RH V2

DSP5D

PM5D/PM5D-RH V2

DSP5D

Owner’s Manual

The above warning is located on the rear/top of the unit.

Explanation of Graphical Symbols

The lightning ﬂash with arrowhead symbol

within an equilateral triangle is intended to alert

the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufﬁcient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the product.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

ampliﬁers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If

the provided plug does not ﬁt into your outlet, consult

an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11 Only use attachments/accessories speciﬁed by the

manufacturer.

12 Use only with the cart, stand,

tripod, bracket, or table speciﬁed

by the manufacturer, or sold with

the apparatus. When a cart is

used, use caution when moving

the cart/apparatus combination

to avoid injury from tip-over.

13 Unplug this apparatus during

lightning storms or when unused for long periods of

time.

14 Refer all servicing to qualiﬁed service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug

is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally,

or has been dropped.

(98-6500)

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions con-

tained in this manual, meets FCC requirements. Modiﬁcations not

expressly approved by Yamaha may void your authority, granted by

the FCC, to use the product.

2. IMPORTANT:

When connecting this product to accessories and/

or another product use only high quality shielded cables. Cable/s

supplied with this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE:

This product has been tested and found to comply with the

requirements listed in FCC Regulations, Part 15 for Class “B” digital

devices. Compliance with these requirements provides a reason-

able level of assurance that your use of this product in a residential

environment will not result in harmful interference with other elec-

tronic devices. This equipment generates/uses radio frequencies

and, if not installed and used according to the instructions found in

the users manual, may cause interference harmful to the operation

of other electronic devices. Compliance with FCC regulations does

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

not guarantee that interference will not occur in all installations. If

this product is found to be the source of interference, which can be

determined by turning the unit “OFF” and “ON”, please try to elimi-

nate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker or

fuse) circuits or install AC line ﬁlter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type of

product. If you can not locate the appropriate retailer, please con-

tact Yamaha Corporation of America, Electronic Service Division,

6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by

Yamaha Corporation of America or its subsidiaries.

FCC INFORMATION (U.S.A.)

* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif.

90620

Telephone : 714-522-9011

Type of Equipment : Digital Mixing System

Model Name : DSP5D

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including

interference that may cause undesired operation.

See user manual instructions if interference to radio reception is

suspected.

(FCC DoC)

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (Perchlorate)

This product contains a battery that contains perchlorate material.

Perchlorate Material—special handling may apply,

See www.dtsc.ca.gov/hazardouswaste/perchlorate.

ADVARSEL!

Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering. Udskiftning

må kun ske med batteri af samme fabrikat og type. Levér det brugte

batteri tilbage til leverandoren.

VARNING

Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller

en ekvivalent typ som rekommenderas av apparattillverkaren.

Kassera använt batteri enligt fabrikantens instruktion.

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo

ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty

paristo valmistajan ohjeiden mukaisesti.

(lithium caution)

NEDERLAND / THE NETHERLANDS

• Dit apparaat bevat een lithium batterij voor geheugen back-up.

• This apparatus contains a lithium battery for memory back-up.

• Raadpleeg uw leverancier over de verwijdering van de batterij op het

moment dat u het apparaat ann het einde van de levensduur of

gelieve dan contact op te nemen met de vertegenwoordiging van

Yamaha in uw land.

•For the removal of the battery at the moment of the disposal at the

end of life please consult your retailer or Yamaha representative

ofﬁce in your country.

• Gooi de batterij niet weg, maar lever hem in als KCA.

• Do not throw away the battery. Instead, hand it in as small chemical

waste.

(lithium disposal)

This product contains a high intensity lamp that contains

a small amount of mercury. Disposal of this material

may be regulated due to environmental considerations.

For disposal information in the United States, refer to

the Electronic Industries Alliance web site:

www.eiae.org

(mercury)* This applies only to the PM5D (PM5D-RH) distributed by

YAMAHA CORPORATION OF AMERICA.

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

WARNING:

THIS APPARATUS MUST BE EARTHED

IMPORTANT. The wires in this mains lead are coloured in accordance

with the following code:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may not

correspond with the coloured markings identifying the terminals in

your plug proceed as follows:

The wire which is coloured GREEN-and-YELLOW must be connected

to the terminal in the plug which is marked by the letter E or by the

safety earth symbol or colored GREEN or GREEN-and-YELLOW.

The wire which is coloured BLUE must be connected to the terminal

which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the termi-

nal which is marked with the letter L or coloured RED.

(3 wires)• This applies only to the DSP5D distributed by

Yamaha-Kemble Music (U.K.) Ltd.

* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif.

90620

Telephone : 714-522-9011

Type of Equipment : Digital Mixing Console

Model Name : PM5D/PM5D-RH

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including

interference that may cause undesired operation.

See user manual instructions if interference to radio reception is

suspected.

(FCC DoC)

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, ﬁre or other hazards. These precautions include, but are not limited to, the following:

• Only use the voltage speciﬁed as correct for the device. The required voltage is

printed on the name plate of the device.

• Use only the speciﬁed power supply (PW800W or an equivalent recommended

by Yamaha).

• (DSP5D only) Use only the included power cord.

If you intend to use the device in an area other than in the one you purchased,

the included power cord may not be compatible. Please check with your Yamaha

dealer.

• Do not place the power cord near heat sources such as heaters or radiators, and

do not excessively bend or otherwise damage the cord, place heavy objects on

it, or place it in a position where anyone could walk on, trip over, or roll anything

over it.

• (DSP5D only) Be sure to connect to an appropriate outlet with a protective

grounding connection. Improper grounding can result in electrical shock.

• Do not open the device or attempt to disassemble the internal parts or modify

them in any way. The device contains no user-serviceable parts. If it should

appear to be malfunctioning, discontinue use immediately and have it inspected

by qualiﬁed Yamaha service personnel.

• Do not expose the device to rain, use it near water or in damp or wet conditions,

or place containers on it containing liquids which might spill into any openings.

If any liquid such as water seeps into the device, turn off the power immediately

and unplug the power cord from the AC outlet. Then have the device inspected

by qualiﬁed Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

• If the power cord or plug becomes frayed or damaged, or if there is a sudden

loss of sound during use of the device, or if any unusual smells or smoke

should appear to be caused by it, immediately turn off the power switch,

disconnect the electric plug from the outlet, and have the device inspected by

qualiﬁed Yamaha service personnel.

• If this device or power supply should be dropped or damaged, immediately turn

off the power switch, disconnect the electric plug from the outlet, and have the

device inspected by qualiﬁed Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the device or other property. These precautions include, but are not limited to, the following:

• Remove the electric plug from the outlet when the device is not to be used for

extended periods of time, or during electrical storms.

• When removing the electric plug from the device or an outlet, always hold the

plug itself and not the cord. Pulling by the cord can damage it.

•Turn the PM5D ON/OFF using only the power supply PW800W POWER switch.

Turning the PM5D ON/OFF by plugging or unplugging the power cord, using a

switch on a power tap, a breaker switch, or similar external means can result in

damage.

• When transporting or moving the device, always use four or more people

(PM5D), two or more people (DSP5D). Attempting to lift the device by yourself

may damage your back, result in other injury, or cause damage to the device

itself.

• Before moving the device, remove all connected cables.

• When setting up the DSP5D, make sure that the AC outlet you are using is easily

accessible. If some trouble or malfunction occurs, immediately turn off the

power switch and disconnect the plug from the outlet. Even when the power

switch is turned off, electricity is still ﬂowing to the product at the minimum

level. When you are not using the product for a long time, make sure to unplug

the power cord from the wall AC outlet.

• If the DSP5D is to be mounted in an EIA-standard rack, leave the back of the

rack open and make sure that it is at least 10 cm away from walls or surfaces.

Also, if the DSP5D is to be mounted with devices that tend to generate heat,

such as power ampliﬁers, be sure to keep an adequate gap between the DSP5D

and the heat-generating devices or install ventilation panels to prevent high

temperatures from developing inside the DSP5D. Inadequate ventilation can

result in overheating, possibly causing damage to the device(s), or even ﬁre.

• Do not use the DSP5D in a conﬁned, poorly-ventilated location. If the DSP5D is

to be used in a small space other than an EIA-standard rack, make sure that

there is adequate space between the device and surrounding walls or other

devices: at least 10 cm behind and 10 cm above. Inadequate ventilation can

result in overheating, possibly causing damage to the device(s), or even ﬁre.

Power supply/Power cord

Do not open

Water warning

If you notice any abnormality

Power supply/Power cord

Location

(5)-8

1/2

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual

•Avoid setting all equalizer controls and faders to their maximum. Depending on

the condition of the connected devices, doing so may cause feedback and may

damage the speakers.

• Do not expose the device to excessive dust or vibrations, or extreme cold or heat

(such as in direct sunlight, near a heater, or in a car during the day) to prevent

the possibility of panel disﬁguration or damage to the internal components.

• Do not place the device in an unstable position where it might accidentally fall

over.

• Do not block the vents. This device has ventilation holes at the front and rear to

prevent the internal temperature from becoming too high. In particular, do not

place the device on its side or upside down. Inadequate ventilation can result in

overheating, possibly causing damage to the device(s), or even ﬁre.

• Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile

phone, or other electric devices. Doing so may result in noise, both in the device

itself and in the TV or radio next to it.

• Before connecting the device to other devices, turn off the power for all devices.

Before turning the power on or off for all devices, set all volume levels to

minimum.

• Remove the power plug from the AC outlet when cleaning the device.

• During extreme changes in temperature or humidity, condensation may occur

and water may collect on the surface of the device. If water is left, the wooden

parts may absorb the water and be damaged. Make sure to wipe any water off

immediately with a soft cloth.

• When turning on the AC power in your audio system, always turn on the power

ampliﬁer LAST, to avoid speaker damage. When turning the power off, the power

ampliﬁer should be turned off FIRST for the same reason.

• Condensation can occur in the device due to rapid, drastic changes in ambient

temperature—when the device is moved from one location to another, or air

conditioning is turned on or off, for example. Using the device while

condensation is present can cause damage. If there is reason to believe that

condensation might have occurred, leave the device for several hours without

turning on the power until the condensation has completely dried out.

• Do not insert your ﬁngers or hands in any gaps or openings on the device

(vents, etc.).

•Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any

gaps or openings on the device (vents, etc.) If this happens, turn off the power

immediately and unplug the power cord from the AC outlet. Then have the

device inspected by qualiﬁed Yamaha service personnel.

• (DSP5D only) Do not apply oil, grease, or contact cleaner to the faders. Doing

so may cause problems with electrical contact or fader motion.

• Do not use the headphones for a long period of time at a high or uncomfortable

volume level, since this can cause permanent hearing loss. If you experience

any hearing loss or ringing in the ears, consult a physician.

• Do not rest your weight on the device or place heavy objects on it, and avoid use

excessive force on the buttons, switches or connectors.

• This device has a built-in backup battery. When you unplug the power cord from

the AC outlet, the internal data of current scene (see page 87) is retained.

However, if the backup battery fully discharges, this data will be lost. When the

backup battery is running low in the system using PM5D or PM5D/DSP5D

Editor, each LCD display indicates “Low Battery!” during operation or “NO

BATTERY!” when starting up the system (the BATTERY ﬁeld also indicates

“LOW” or “NO BATTERY” in the PREFERENCE2 screen).

When using only the DSP5D, the message such as “Low Battery!” cannot be

displayed because the DSP5D itself has no LCD display. When the DSP5D is

cascade-connected to the PM5D or online with the DSP5D Editor, these

messages will be displayed. In this case, have qualiﬁed Yamaha service

personnel replace the backup battery.

Always turn the power off when the device is not in use.

The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualiﬁed Yamaha service

personnel about replacing defective components.

Connections

Maintenance

Handling caution

Backup battery

XLR-type connectors are wired as follows (IEC60268 standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-).

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the device, or data that is lost or destroyed.

Included Accessories

PM5D/PM5D-RH

• Owner's Manual (this document)

• Gooseneck Lamps x 3

• Power Supply PW800W Connection Cable

DSP5D

• Owner's Manual (this document)

• AC Power Cord

• D-SUB 68-pin Cable 10 m x 2

(5)-8

2/2

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual

Table of Contents

Table of Contents — Operating section

Introduction.......................................... 10

Thank you ....................................................................... 10

An overview of the PM5D system .................................... 10

Differences between the PM5D model and

the PM5D-RH model ........................................... 11

About the channel structure of the PM5D ................................12

About the DSP5D ............................................................ 12

Differences with the PM5D.........................................................12

Regarding cascade connections between the PM5D and

DSP5D ................................................................................13

About PM5D Editor and DSP5D Editor ............................ 13

Firmware versions ............................................................ 14

Major new functionality in PM5D firmware V2.0 ............. 14

Regarding word clock synchronization ............................ 15

How this manual is organized.......................................... 15

Conventions in this manual........................................................15

Top, front, and rear panels.................. 16

Top panel ........................................................................ 16

Rear panel........................................................................ 18

Front panel ...................................................................... 20

DSP5D front panel........................................................... 21

DSP5D rear panel ............................................................ 22

Basic operation on the PM5D.............. 23

About the various types of user interface ......................... 23

User interface in the display........................................................23

DISPLAY ACCESS section..........................................................24

Data Entry section........................................................................24

External user interface .................................................................25

Basic operation ................................................................ 26

Click ..............................................................................................26

Drag...............................................................................................26

Drag and drop ..............................................................................26

Accessing a desired screen ...........................................................27

Moving the cursor........................................................................27

Scrolling the screen ......................................................................28

Operating the buttons .................................................................29

Adjusting the setting of a knob or fader.....................................29

Assigning a name .........................................................................30

Connections and setup ........................ 31

Examples of systems expanded with the DSP5D ............. 31

Example of simple input expansion

(PM5D + one DSP5D unit)..............................................31

PM5D + remotely connected input expansion

(PM5D + DCU5D + two DSP5D units)..........................31

Control from DSP5D Editor (one DSP5D unit + PC) .............32

Audio connections........................................................... 33

Analog audio connections...........................................................33

Analog output connections.........................................................34

Digital input/output connections...............................................36

Installing an option card .............................................................37

Word clock connections and settings .............................. 38

About word clock.........................................................................38

Selecting the word clock master..................................................38

Restoring the current scene to the default state............... 40

Switching the target of panel operations

(when cascade-connected with the DSP5D)........ 40

Input channel operations .....................41

About the input channels ................................................ 41

AD IN section .................................................................. 43

Items in the AD IN section......................................................... 43

Controlling the input sensitivity and phantom power

(+48V) of the head amp ................................................... 44

INPUT channel strip......................................................... 45

Items in the INPUT channel strip.............................................. 45

ST IN/FX RTN channel strip ............................................. 47

Items in the ST IN/FX RTN channel strip ................................ 47

FADER FLIP/ENCODER MODE section ............................. 48

Items in the FADER FLIP/ENCODER MODE section ........... 48

Various operations for input channels.............................. 49

Selecting the function of the encoders....................................... 49

Exchanging the fader and encoder functions............................ 49

Sending a signal from an input channel to the STEREO

bus ...................................................................................... 50

Sending the signal from the input channel to a MIX bus ........ 51

Enabling/disabling pairing.......................................................... 53

Output channel operations ..................55

About the output channels.............................................. 55

MIX section ..................................................................... 57

Items in the MIX section ............................................................ 57

Operations in the MIX section................................................... 57

STEREO A/B channel strip ................................................ 61

Items in the STEREO A/B channel strip ................................... 61

Operations in the STEREO A/B channel strip .......................... 62

MATRIX section ............................................................... 63

Items in the MATRIX section .................................................... 63

Operations in the MATRIX section........................................... 63

Using the Selected Channel section.....65

About the SELECTED CHANNEL section .......................... 65

Items in the SELECTED CHANNEL section ....................... 65

GROUP ........................................................................................ 65

CHANNEL SELECT ................................................................... 66

DELAY ......................................................................................... 66

GAIN/ATTENUATION/ø (Gain / Attenuation / Phase) ........ 67

NOISE GATE............................................................................... 67

STEREO ....................................................................................... 68

COMPRESSOR ........................................................................... 68

HPF (High Pass Filter)................................................................ 69

EQUALIZER................................................................................ 69

Operations in the SELECTED CHANNEL section .............. 70

Selecting a channel and editing its parameters ......................... 70

Compressor operations............................................................... 71

Gate operations ........................................................................... 72

EQ/HPF operations..................................................................... 73

Input Patch / Output Patch operations .74

Changing the input patch settings .................................. 74

Changing the output patch settings................................ 75

Inserting an external device into a channel...................... 77

Connecting an external device for insertion ............................. 77

Patching the insert-out and insert-in ........................................ 78

Directly outputting the signal of an input channel .......... 80

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual

Table of Contents

Grouping and linking............................81

About DCA Groups and Mute Groups ............................. 81

Items in the ASSIGN MODE section ................................. 81

Items in the DCA strip...................................................... 81

Using DCA Groups........................................................... 82

Assigning channels to DCA groups............................................82

Controlling DCA groups.............................................................83

Using mute groups .......................................................... 83

Assigning channels to mute groups............................................83

Controlling mute groups.............................................................84

Using the Mute Safe function .....................................................84

Using EQ Link and Compressor Link ................................ 85

Scene memory....................................87

About scenes ................................................................... 87

Items in the SCENE MEMORY section .............................. 88

Using scene memories ..................................................... 89

Storing a scene..............................................................................89

Recalling a scene...........................................................................90

Using PREVIEW mode ...................................................... 90

Using the Auto Store function.......................................... 91

Using the Direct Recall function ....................................... 91

Using the Selective Recall function................................... 92

Using the Recall Safe function.......................................... 94

Using the Fade function................................................... 95

Using the Tracking Recall function ................................... 96

Using the Global Paste function ....................................... 97

Monitor and Cue................................99

About the MONITOR and CUE sections........................... 99

Using the Monitor function ........................................... 100

Items in the MONITOR section...............................................100

Monitoring a signal....................................................................101

Using the Cue/Solo functions ........................................ 102

Items in the CUE section...........................................................102

About CUE mode and SOLO mode.........................................102

Cue and Solo groups..................................................................103

Using the Cue function .............................................................104

Using the Solo function.............................................................104

Talkback and Oscillator....................105

About the TALKBACK/OSCILLATOR sections.................. 105

Items in the TALKBACK/OSCILLATOR sections..................105

Using talkback ............................................................... 106

Using the oscillator ........................................................ 107

Meters...............................................108

Items in the meter section ............................................. 108

Switching the meter display........................................... 108

Switching the metering point ........................................ 109

Specifying the metering point for input channels...................109

Specifying the metering point for output channels ................109

Viewing the gain reduction of the internal gates and

compressors....................................................... 110

Viewing the gain reduction for input channels .......................110

Viewing the gain reduction for output channels.....................110

Effects ...............................................111

About the internal effects............................................... 111

Using an internal effect via a MIX bus ............................ 112

Inserting an internal effect into a channel ...................... 113

Basic operations in the effect screen .............................. 114

Recalling settings from the effect library..................................114

Editing the effect parameters ....................................................115

Storing settings in the effect library ..........................................115

Using the Tap Tempo function ...................................... 116

Using the Freeze effect................................................... 117

Graphic EQ and Parametric EQ .......118

Patching the GEQ modules............................................ 118

Expanding the GEQ modules......................................... 119

Basic graphic EQ operations .......................................... 119

Controlling the graphic EQ from the display ......................... 119

Controlling the graphic EQ from the DCA section................ 120

Basic parametric EQ operations ..................................... 121

Controlling the parametric EQ from the display.................... 121

Controlling the parametric EQ from the SELECTED

CHANNEL section.......................................................... 122

Remote control ................................123

MIDI on the PM5D ........................................................ 123

Using program changes to control events ..................... 123

Using control changes to control events........................ 125

Using the MIDI Remote function ................................... 127

Assigning MIDI messages to controllers ................................. 127

Using MIDI remote channels................................................... 131

Transmitting MIDI events when you switch scenes........ 132

Using GPI (General Purpose Interface) ........................... 133

Using GPI IN ............................................................................. 133

Calibrating the GPI IN ports .................................................... 135

Using GPI OUT......................................................................... 136

Using memory cards........................138

Using memory cards with the PM5D............................. 138

Saving files to a memory card........................................ 138

Loading files from a memory card ................................. 140

Surround pan ...................................142

About surround pan ...................................................... 142

Bus configuration and operation in surround mode ...... 143

About the surround buses ........................................................ 143

How the MIX section will operate ........................................... 143

Basic settings for surround buses ................................... 144

Controlling surround pan .............................................. 145

Notes regarding surround pan ...................................... 147

Other functions................................148

Using the user defined keys ........................................... 148

Items in the USER DEFINED section ..................................... 148

Assigning functions to the User Defined keys ........................ 148

Executing functions assigned to the User Defined keys......... 149

Using the FADER MODE section .................................... 149

Items in the FADER MODE section........................................ 149

Assigning the FADER MODE section layer ............................ 149

Switching the FADER MODE section layer............................ 150

Locking the PM5D (Security functions).......................... 151

Setting the System Password or Console Password................ 151

Using Parameter Lock or Console Lock.................................. 152

Using cascade connections ............................................ 153

Example of cascade connections between the PM5D and

DSP5D.............................................................................. 153

Example of cascade connections between PM5D units ......... 153

Specifying the DSP5D’s machine ID number......................... 153

Basic settings for cascade connection ...................................... 154

Selecting the buses used for cascade connection .................... 156

Connecting the PM5D to your computer via USB ......... 158

Caution when using the USB TO HOST connector .............. 158

Connecting the DSP5D to your computer via Ethernet . 159

Initializing the PM5D’s internal memory........................ 160

Initializing the DSP5D’s internal memory....................... 160

Adjusting the faders and input/output gain

(Calibration) ...................................................... 161

Calibrating the faders................................................................ 161

Adjusting the analog input gain (PM5D-RH model only).... 162

Adjusting the output gain......................................................... 162

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual

Table of Contents

Table of Contents — Reference section

Information shown in the display.......... 163

Upper part of the display (always visible)....................... 163

Main area of the display ................................................ 164

Lower part of the display (always visible) ....................... 164

Function menu........................................ 165

Global functions...................................... 166

EFFECT functions ........................................................... 166

EFFECT PARAM (Effect parameter) screen ...........................166

EFFECT ASSIGN screen............................................................168

EFFECT LIBRARY screen .........................................................169

PLUG-IN screen.........................................................................170

GEQ function................................................................. 170

GEQ PARAM (GEQ parameter) screen ..................................170

GEQ ASSIGN screen .................................................................173

GEQ LIBRARY screen ...............................................................174

SCENE function ............................................................. 175

SCENE screen.............................................................................175

EVENT LIST screen...................................................................177

SELECTIVE RECALL screen ....................................................180

RECALL SAFE screen ................................................................182

FADE TIME screen....................................................................184

TRACKING RECALL screen ....................................................186

GLOBAL PASTE screen ............................................................187

MIDI REMOTE function ................................................. 188

MIDI SETUP screen ..................................................................188

MIDI PGM CHANGE (MIDI program change) screen ........190

MIDI CTRL CHANGE (MIDI control change) screen..........191

MIDI REMOTE screen..............................................................192

GPI screen...................................................................................194

FADER START screen...............................................................196

TRANSPORT screen .................................................................198

DME CONTROL screen ...........................................................199

UTILITY function ............................................................ 204

PREFERENCE 1/2 screens ........................................................204

USER DEFINE screen................................................................208

SAVE screen ...............................................................................211

LOAD screen ..............................................................................215

FADER ASSIGN screen .............................................................217

SECURITY screen......................................................................218

SYS/W.CLOCK function ................................................. 219

WORD CLOCK screen..............................................................219

MIXER SETUP screen...............................................................221

CASCADE screen.......................................................................226

HA (Head Amp) screen.............................................................228

OUTPUT PORT ATT (Output port attenuation) screen ......229

DITHER screen ..........................................................................229

HA LIBRARY screen..................................................................230

METER function ............................................................. 231

INPUT METER screen ..............................................................231

OUTPUT METER screen..........................................................232

INPUT GR (Input Gain Reduction) screen.............................233

OUTPUT GR (Output Gain Reduction) screen .....................234

MON/CUE function ....................................................... 234

TALKBACK screen ....................................................................234

OSCILLATOR screen ................................................................236

2TR I/O screen ...........................................................................237

MONITOR screen .....................................................................238

CUE/SOLO screen .....................................................................240

Output functions .................................... 243

OUTPUT PATCH function .............................................. 243

OUTPUT PATCH screen ......................................................... 243

INSERT PATCH screen............................................................ 244

INSERT POINT screen............................................................. 246

NAME screen............................................................................. 247

OUTPUT PATCH LIBRARY screen ....................................... 247

OUTPUT INSERT function.............................................. 248

INSERT IN MIX 1-24 screen ................................................... 248

INSERT IN MATRIX/STEREO/MONITOR screen .............. 248

HA LIBRARY screen ................................................................. 249

OUTPUT EQ function .................................................... 250

EQ PARAM (EQ Parameter) screen........................................ 250

MIX 1-24 screen ........................................................................ 251

MATRIX/STEREO screen ........................................................ 251

OUTPUT EQ LIBRARY screen................................................ 252

OUTPUT COMP function............................................... 253

COMP PARAM (Compressor parameter) screen.................. 253

MIX 1-24 screen ........................................................................ 255

MATRIX/STEREO screen ........................................................ 255

COMP LIBRARY (Compressor library) screen...................... 256

OUTPUT DELAY function ............................................... 257

MIX 1-24 screen ........................................................................ 257

MATRIX/STEREO screen ........................................................ 257

OUTPUT DCA/GROUP function..................................... 258

DCA GROUP ASSIGN screen ................................................. 258

MUTE GROUP ASSIGN screen .............................................. 259

EQ LINK ASSIGN screen ......................................................... 260

COMP LINK ASSIGN (Compressor link assign) screen ....... 261

MATRIX/ST function...................................................... 262

MATRIX/ST ROUTING screen............................................... 262

MIX to MATRIX VIEW screen................................................ 264

LCR screen ................................................................................. 267

SURR SETUP screen................................................................. 268

OUTPUT VIEW function ................................................. 270

CH VIEW (Channel view) screen............................................ 270

SIGNAL FLOW screen ............................................................. 272

FADER VIEW screen ................................................................ 273

CH JOB (Channel job) screen.................................................. 274

OUTPUT CH LIBRARY screen ............................................... 275

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual

Table of Contents

Input functions ........................................277

INPUT PATCH function .................................................. 277

INPUT PATCH screen..............................................................277

DIRECT OUT PATCH screen..................................................278

INSERT PATCH screen ............................................................279

INSERT/DIRECT OUT POINT screen ...................................281

NAME screen .............................................................................282

INPUT PATCH LIBRARY screen ............................................283

INPUT HA/INSERT function............................................ 283

CH 1-24 (Input channel 1-24) screen ......................................283

CH 25-48 (Input channel 25-48) screen ..................................283

STIN/FXRTN (ST IN/FXRTN channel) screen ......................283

INSERT 1-24 screen...................................................................284

INSERT 25-48 screen.................................................................284

INSERT STIN screen .................................................................284

HA LIBRARY screen..................................................................285

INPUT ø/EQ function ..................................................... 286

EQ PARAM (EQ parameter) screen ........................................286

EQ 1-24 screen ...........................................................................287

EQ 25-48 switch .........................................................................287

EQ STIN/FXRTN screen...........................................................287

ø/ATT 1-48 (Phase/Attenuation 1-48) screen.........................288

ø/ATT STIN/FXRTN (Phase/Attenuation STIN/FXRTN)

screen ................................................................................288

INPUT EQ LIBRARY screen ....................................................289

INPUT GATE/COMP function......................................... 289

GATE PARAM (Gate parameter) screen.................................289

COMP PARAM (Compressor parameter) screen ..................291

CH 1-12 (Input channel 1–12) screen .....................................293

CH 13-24 (Input channel 13–24) screen .................................293

CH 25-36 (Input channel 25–36) screen .................................293

CH 37-48 (Input channel 37–48) screen .................................293

ST IN (ST IN channel) screen...................................................293

GATE LIBRARY screen.............................................................294

COMP LIBRARY (Compressor library) screen ......................295

INPUT DELAY function................................................... 295

CH 1-24 (Input channel 1–24) screen .....................................295

CH 25-48 (Input channel 25–48) screen .................................295

ST IN (ST IN channel) screen...................................................295

INPUT DCA/GROUP function......................................... 296

DCA GROUP ASSIGN screen ..................................................296

MUTE GROUP ASSIGN screen...............................................297

EQ LINK ASSIGN screen..........................................................298

COMP LINK ASSIGN (Compressor link assign) screen .......299

PAN/ROUTING function ................................................ 299

CH to MIX (Channel to mix) screen .......................................299

MIX SEND VIEW screen ..........................................................305

FIX ASSIGN VIEW screen ........................................................307

LCR screen..................................................................................308

SURR PARAM (Surround parameter) screen.........................309

SURR VIEW (Surround view) screen ......................................310

M/S screen ..................................................................................311

INPUT VIEW function ..................................................... 311

CH VIEW (Channel view) screen ............................................311

SIGNAL FLOW screen ..............................................................313

FADER VIEW screen.................................................................314

CH JOB screen ...........................................................................314

INPUT CH LIBRARY (Input channel library) screen............316

Appendices..............................................317

EQ Library List................................................................ 317

GATE Library List............................................................ 318

Compressor Library List ................................................. 319

Dynamics Parameters .................................................... 321

GATE section............................................................................. 321

COMP section ........................................................................... 322

Effect Library List............................................................ 324

Effects Parameters.......................................................... 325

Effects and tempo synchronization ......................................... 336

Scene Memory/Effect Library to Program Change Table

.. 337

Parameters that can be assigned to control changes ..... 341

Control change parameter assignments ........................ 343

NRPN parameter assignments ....................................... 360

Channel Library List ....................................................... 364

List of parameters available for Pair, Recall Safe or

OUTPUT ISOLATION operation ......................... 365

MIDI Data Format.......................................................... 368

Warning Messages......................................................... 377

Error Messages............................................................... 379

Troubleshooting ............................................................ 380

General Specifications.................................................... 381

PM5D/PM5D-RH..................................................................... 381

DSP5D........................................................................................ 383

Input/output characteristics........................................... 384

Electrical characteristics ................................................. 389

PM5D/PM5D-RH..................................................................... 389

DSP5D........................................................................................ 391

Mixer Basic Parameters .................................................. 393

Pin Assignment.............................................................. 394

Dimensions.................................................................... 395

MIDI Implementation Chart .......................................... 396

Index ............................................................................. 397

PM5D/PM5D-RH Block Diagram ...................End of Manual

DSP5D Block Diagram ...................................End of Manual

PM5D Level Diagram.....................................End of Manual

PM5D-RH Level Diagram ...............................End of Manual

DSP5D Level Diagram ...................................End of Manual

• The illustrations and screen displays as shown in this

Owner’s Manual are for instructional purposes only,

and may be different from the ones on your device.

• The company names and product names in this

Owner’s Manual are the trademarks or registered

trademarks of their respective companies.

10 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Operating section

Thank you

Thank you for purchasing the Yamaha PM5D digital mixing console and/or Yamaha DSP5D digital mixing system. In order

to take full advantage of the PM5D/DSP5D’s superior functionality and enjoy years of trouble-free use, please read this man-

ual before you begin using the product. After you have read the manual, keep it in a safe place.

An overview of the PM5D system

The PM5D is an expandable digital mixing console with the following features.

❏ Full digital SR mixing system

The PM5D is a full-digital SR mixing console that takes

advantage of cutting-edge digital audio processing technol-

ogy. 24-bit linear AD/DA converters are used to deliver up

to 110 dB of dynamic range and amazing sound quality. As

input channels, it provides 48 monaural channels, four ste-

reo channels, and four stereo channels for effect return. As

output channels, it provides 24 MIX channels, eight

MATRIX channels, and two STEREO channels. The PM5D

can be used in a wide range of applications. You can assign

desired channels to be controlled by the eight DCA faders

on the panel, and use them as group faders.

❏ PM5D model and PM5D-RH model

In addition to the standard PM5D model that provides

manual control of the head amp for each input, the

PM5D-RH model is also available, providing programma-

ble control of head amp input sensitivity and phantom

power settings. You can choose the model appropriate for

your situation and budget.

❏ Cutting-edge user interface

For the input channels and STEREO A/B channels, dedi-

cated channel strips are provided where you can operate

the fader, pan, cue, and on/off controls. For MIX channels

and MATRIX channels, encoders allow you to control the

send level and master level. The PM5D allows quick and

intuitive operation just as on an analog mixer. In addition,

you can use the SELECTED CHANNEL section to manu-

ally control the principal parameters (delay, EQ, gate,

compressor) of the desired channel.

❏ Eight effect modules / Twelve graphic

EQ modules

Eight high-quality multi-effect modules are built in. Effects

such as reverb, delay, multiband compressor, and various

modulation effects can be routed via internal buses or

inserted into the desired channel. 31-band graphic EQ

(alternatively, 8-band parametric EQ) can also be inserted

into any channel or any output.

❏ Add-On effects provided as standard

As effect types, the channel strip package (COMP276/276S,

COMP260/260S, EQ601), master strip package (OPEN

DECK), and reverb package (REV-X) are provided as

standard.

❏ Scene memories and libraries

Mix parameters and internal effect settings can be stored in

memory as up to 500 scenes for immediate recall. Effects,

input/output patching, input channel/output channel set-

tings, internal head amp (PM5D-RH model only) or

external head amp settings can be stored in various librar-

ies, independently of scenes.

❏ Digital cascade connection

Up to four PM5D units, or one PM5D and one Yamaha

DM2000/02R96 unit, can be cascade-connected to share

buses in the digital domain. In particular when PM5D

units are cascaded together, operations such as scene sav-

ing and recall can also be linked. DME64N can also be used

as inserts or as extended signal processors via a cascade

connection.

❏ Surround panning

Surround pan functionality allows multi-channel playback

systems to be used, letting you place the signal of an input

channel in two-dimensional space, or move the sound

image forward/backward and left/right. 3-1ch, 5.1ch, and

6.1ch surround modes are available.

❏ I/O card expansion

The rear panel provides four slots in which separately sold

mini-YGDAI cards can be installed. AD cards, DA cards, or

digital I/O cards can be installed in these slots to add inputs

and outputs.

❏ Expansion via the DSP5D

A maximum of two DSP5D digital mixing systems can be

cascade-connected to a PM5D to expand the inputs and

outputs. You can also connect a Yamaha DCU5D digital

cabling unit between the PM5D and DSP5D, and locate the

DSP5D remotely.

1 Introduction

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 11

Introduction

Differences between the PM5D model and the PM5D-RH

model

The PM5D is available as the standard PM5D model or as the PM5D-RH model which allows internal head amp settings to be

programmed. These models differ as follows.

❏ PM5D model

• Head amp adjustments (input sensitivity settings,

phantom power (+48V) on/off) for the analog inputs

(INPUT jacks 1–48, ST IN jacks 1–4) are performed

manually, using the controls of the top panel.

• Insert jacks (INSERT IN/OUT jacks) for the monaural

analog inputs (INPUT jacks 1–48) are provided on the

rear panel, allowing external effect processors to be

inserted in the analog domain.

• ST IN jacks 1–4 are only for line level.

• There is no +48V MASTER switch.

❏ PM5D-RH model

• Head amp adjustments (input sensitivity settings,

phantom power (+48V) on/off) for the analog inputs

are controlled from within the screen via software. For

this reason, the top panel does not have head amp con-

trols; instead, LEDs showing the presence or absence of

a signal are provided. Head amp settings can be saved

in a library and recalled at any time.

• Insert jacks for the analog inputs are not provided.

• ST IN jacks 1–4 support mic levels through line levels.

Phantom power can also be supplied to ST IN jacks 1–

• The +48V MASTER switch turns all phantom power

(+48V) on/off.

INPUT jacks 1–48ST IN jacks 1–4

INSERT IN/OUT jacks 1–48

INPUT jacks 1–48

ST IN jacks 1–4

1 Introduction

12 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

The PM5D provides the following input channels and out-

put channels.

❏ Input channels

This section processes input signals and sends them to the

STEREO bus or MIX buses. There are three types of input

channel, as follows.

• Input channels 1–48

These channels are used to process monaural signals.

By default, the input signals from the monaural analog

input jacks (INPUT jacks 1–48) are assigned to these

channels.

• ST IN channels 1–4

These channels are used to process stereo signals. By

default, the input signals from the stereo analog input

jacks (ST IN jacks 1–4) are assigned to these channels.

• FX RTN channels 1–4

These channels are used mainly to process the return

signals (stereo) from the internal effects. By default, the

left/right output channels of internal effects 1 through

4 are assigned to these channels.

Hint

Signal assignments to the input channels can be changed as

desired.

❏ Output channels

This section mixes the signals sent from input channels

etc., and sends them to the corresponding output jacks or

output buses. There are three types of output channel, as

follows.

• MIX channels 1–24

These channels process signals sent from input chan-

nels to MIX buses. In the initial state, output signals are

assigned to MIX OUT jacks 1–24. These channels are

used mainly for foldback or as sends to external effects.

The signals of MIX channels 1–24 can also be sent to

the STEREO bus or MATRIX buses.

• MATRIX channels 1–8

These process the signals sent from MIX channels or

STEREO A/B channels to MATRIX buses, and output

them from the MATRIX OUT jacks. This allows MIX

channels or STEREO A/B channels to be mixed at the

desired balance for output.

• STEREO A/B channels

These process the signals sent from input channels or

MIX channels, and output them to STEREO OUT

jacks A/B. These channels are used as the main stereo

outputs. Normally, the same signal is sent from the

STEREO A and B channels. However, it is also possible

to use the STEREO B channel as the center channel for

three-channel L/C/R playback.

About the DSP5D

The DSP5D is a digital signal processing (DSP) system

expanding the inputs and outputs of the PM5D.

• Its audio processing capability is equivalent to that of

the PM5D-RH. As analog audio input/output jacks, it

provides INPUT jacks 1–48, ST IN jacks 1–4, and

OMNI OUT jacks 1–24.

• Up to two DSP5D units can be cascade-connected to

one PM5D. By connecting it with DSP5D units, the

PM5D system can be expanded to a maximum of 168

channels of input (144 channels + 12 ST).

• By switching the control target on the PM5D, the

DSP5D can be seamlessly controlled in the same way as

the PM5D itself.

• You can use DSP5D Editor application software to

remotely control and edit the parameters of the

DSP5D. Only Windows computers are supported.

• The DSP5D can be connected to a Yamaha DCU5D

digital cabling unit and placed on stage, and operated

remotely from the PM5D.

• The front panel provides two slots in which you can

install separately sold mini-YGDAI cards to add inputs

and outputs in a variety of digital formats.

❏ Connectors and interfaces not found on

the DSP5D

• INSERT IN/OUT jacks, MIX OUT jacks, LAMP jacks,

MONITOR OUT jacks, CUE OUT jacks, STEREO

OUT A/B jacks, MATRIX OUT jacks, 2TR IN ANA-

LOG jacks, TIME CODE INPUT jack, USB TO HOST

connector, GPI connector, RS422 REMOTE connec-

tor, HA REMOTE connector, MIDI IN/THRU/OUT

connectors, 2TR OUT DIGITAL jack, 2TR IN DIGI-

TAL jack, SLOT 3–4, MEMORY CARD slot, MOUSE

connector, KEYBOARD connector, PHONES jack

• Controllers such as faders, display devices such as

meters. LCD display, +48V MASTER switch (PM5D-

RH), 75Ω ON/OFF switch

❏ Connectors and interfaces found only

the DSP5D

• OMNI OUT jacks, CASCADE IN/OUT RJ-45 connec-

tors, NETWORK connector, AC IN connector

• POWER switch, mode switch, FAN switch

About the connectors: Since the DSP5D does not have

the functionality for the connectors with which DSP5D

is not equipped, these functions and connectors are not

shown in the screen of the PM5D or DSP5D Editor.

About the channel structure of the

PM5D

Differences with the PM5D

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 13

Introduction

About the interface: Since the DSP5D does not have

controllers such as faders or the LCD display, it is oper-

ated from the PM5D or DSP5D Editor.

Note

• The explanations in chapter 5 and following of this Owner’s

Manual are based on the functionality and operating proce-

dures of the PM5D. Supplementary explanations regarding

the DSP5D are added only in cases where there is a signifi-

cant difference in functionality or operating procedure.

However, in cases where it is obvious that the above-

described differences would make clear differences in oper-

ation or in the on-screen display, explanations for the

DSP5D will be omitted.

• There are some differences between the PM5D and DSP5D

in the I/O cards that are supported. For the most recent

information regarding I/O cards, refer to the following

Yamaha website.

http://www.yamahaproaudio.com/

❏ Connection to a computer

The PM5D can be connected to a computer via a USB

cable from its USB TO HOST connector, but the DSP5D

can be connected to a computer via an Ethernet CAT5

cable from its NETWORK connector.

By bi-directionally cascade-connecting the PM5D and

DSP5D, you can share MIX buses 1–24, STEREO A/B

buses, and CUE buses.

For details on cascade connections, refer to p.153.

Note

• Cascade connection with the DSP5D is possible only for

PM5D V2.0 or later. If you’re using earlier version than V2.0,

you will need to upgrade to PM5D V2.0 or later. You can

download the most recent firmware from the following

Yamaha website.

http://www.yamahaproaudio.com/

• Connectors and interfaces not found on the DSP5D cannot

be controlled from the PM5D. For example, the MONITOR

[LEVEL] and MONITOR [PHONES] knobs found on the

PM5D’s top panel are always operated at the level of the

PM5D.

❏ Controlling the DSP5D

• As the target of control from the PM5D’s panel and

screen, you can recall machine #1 (PM5D), machine #2

(first DSP5D), or machine #3 (second DSP5D) as

desired. For details on operation, refer to p.153.

• Functions assigned to the user-defined keys or the

FADER MODE section can be used to select the

DSP5D as the target machine to be operated (➥ p.148,

149). Operations can be performed from the panel of

the PM5D itself or from DSP5D Editor connected to

the DSP5D.

❏ Operation when cascade-connected

• Output channels

In general, operations for the output channels of cas-

cade-connected buses will be linked between machines.

(You can also specify that they not be linked.) This

means that you can operate the system as if it were a

single console with an expanded number of inputs.

However, since the inserts to output channels will also

be duplicated, inserted GEQ modules and effects may

also be consumed in duplicate or triplicate. (Separate

GEQ modules or effects are inserted into the linked

buses on each machine.)

• Scene memories and libraries

Scene memory and library data is stored on each

machine. When a scene or a library associated with a

scene is stored or recalled, the same scene/library num-

ber will be stored/recalled on all machines. When the

cascade-connection becomes active, the PM5D’s

library data not associated with a scene will be sent to

each DSP5D to synchronize the libraries. The data on

cascade-connected machines can also be saved together

to a memory card.

• Effects

The DSP5D provides GEQ modules and effects that are

equivalent to those on the PM5D, but since the con-

nections between machines are bus cascade

connections, inserts into input channels are limited to

being within each machine.

• DCA groups / Mute groups

These will operate in tandem for cascade-connected

PM5D/DSP5D machines. (➥ p.156)

• CH JOB function

Channel copy operations between the PM5D/DSP5D

can be performed from the PM5D front panel. How-

ever, channels can be moved using the INPUT VIEW

function only within each machine. (➥ p.274, 314)

About PM5D Editor and DSP5D Editor

These programs are application software for operating the

PM5D/DSP5D’s functionality from a computer. You can

use this software to remotely control and edit the parame-

ters of the PM5D/DSP5D.

The USB-MIDI driver (for the PM5D) or DME-N Net-

work driver (for the DSP5D) required for connection with

a computer, as well as the PM5D/DSP5D editor, can be

downloaded from the following Yamaha website.

http://www.yamahaproaudio.com/

Note

DSP5D Editor supports only Windows computers.

Regarding cascade connections

between the PM5D and DSP5D

1 Introduction

14 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Firmware versions

You can download the most recent firmware from the following Yamaha website.

http://www.yamahaproaudio.com/

For either the PM5D or the DSP5D, you can check the firmware version in the UTILITY function PREFERENCE 2 screen

(➥ p.207).

Major new functionality in PM5D ﬁrmware V2.0

The major new functionality and improvements that were added in conjunction with the upgrade to firmware V2.0 are as

follows.

❏ Basic functionality and panel operations

• You can now control the DSP5D from the PM5D’s

panel. (➥ p.153)

• On/off operations of the channel selected in the

FADER MODE section can now be operated from the

DCA [MUTE] key.

• Even if the FADER [FLIP] key is on, you can now use

the encoders to control the panning of the signal sent

to the MIX buses, the head amp gain, or the attenua-

tors. (➥ p.49)

• If there is no vacant library number when you store the

selected scene as NEW, it will now be impossible to

save the scene; this prevents an existing library item

from being overwritten.

• Remote control of the DME64N/24N (firmware V2.0

and later) is now faster. In particular, operation is

faster when connected via an MY16-C or MY16-CII

card (supported from V1.2).

• As parameters that can be operated in the screen,

MONITOR LEVEL and CUE LEVEL have been added.

You can now assign these to the faders of the DCA strip

so that the monitor or cue levels can be adjusted.

(➥ p.149)

❏ EFFECT functions

• Add-On Effects (COMP276/276S, COMP260/260S,

EQ601, OPEN DECK) and DE-ESSER have been

added.

•A DSP CONFIGURATION option has been added to

the EFFECT ASSIGN screen and to the GEQ function

GEQ ASSIGN screen, allowing internal effects 1–8 to

be used as graphic EQ or parametric EQ.

(➥ p.168, 173)

• When the panel [SEL] key is pressed in the EFFECT

PARAM screen, or when a [SEL] key is turned on via a

linking setting, the effect module inserted in that chan-

nel will automatically be selected.

• If you’ve used the tap tempo function to specify the

tempo in the EFFECT PARAM screen and then edited

the DELAY parameter, the tempo will now stay

unchanged.

❏ GEQ functions

• Options have been added to the GEQ PARAM screen,

allowing you to switch a graphic EQ to a parametric

EQ. (➥ p.170)

• Not only when the panel [SEL] key is pressed in the

GEQ PARAM screen but also when a [SEL] key is

turned on via a linking setting, the GEQ module

inserted in that channel will automatically be selected.

• When you insert a GEQ in the GEQ PARAM screen,

insert-in will automatically be turned on for that chan-

nel, and will be automatically turned off when you

remove the GEQ.

❏ SCENE functions

• In the SCENE screen, you can now specify “read-only”

scenes that will not be overwritten when you load

scenes from a memory card. (➥ p.175)

• In the SCENE screen, a DELAY field has been added,

allowing you to specify the timing of the program

change or MIDI events that are transmitted when the

scene is recalled. (➥ p.175)

• In the SELECTIVE RECALL screen and the RECALL

SAFE screen, the ON parameter has been added as a

channel parameter that can be included in or excluded

from recall operations. (➥ p.180, 182)

• In the SELECTIVE RECALL screen and RECALL SAFE

screen, separately from the conventional Recall Safe

functionality, an OUTPUT ISOLATION field has been

added, so that output channels and parameters to be

excluded from recall operations can be stored in

SETUP memory (which is not affected by memory

card load operations). (➥ p.180, 182)

❏ SYS/W.CLOCK functions

• In the MIXER SETUP screen, a VIRTUAL SOUND-

CHECK button has been added, allowing you to

temporarily switch the input signals without affecting

the scene memory (input patching). For example, this

allows you to perform a sound check using pre-

recorded material played back by a DAW connected to

a slot, instead of the analog input material received via

the INPUT jacks. (➥ p.221)

• In the OUTPUT ATT PORT screen, a ø (phase) but-

ton has been added, allowing you to switch the phase

between normal and reverse for each output channel or

I/O channel output port.

❏ UTILITY functions

• In the PREFERENCE 1 screen, a DCA MUTE TAR-

GET option has been added, allowing you to specify

that the DCA [MUTE] key will mute the send to the

MIX bus. (➥ p.205)

• In the PREFERENCE 1 screen, an ATT OPERATION

ON PANEL option has been added, allowing you to

prevent the panel encoders from operating the attenua-

tors. (➥ p.206)

• In the PREFERENCE 1 screen, a MIX SEL/ENCODER

MODE LINK option has been added, allowing you to

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 15

Introduction

link selection of MIX channels with selection of MIX

SEND SELECT keys. (➥ p.206)

• In the USER DEFINE screen, functions such as DSP5D

CONTROL and ENCODER MODE KEY have been

added to the functions that can be assigned to user-

defined keys. (➥ p.208)

• In the FADER ASSIGN screen, options have been

added, allowing you to use the STEREO/DCA strip sec-

tion to control the monitor/cue level and on/off status.

(➥ p.217)

• In the FADER ASSIGN screen, you can now assign the

desired channels of the DSP5D as well. (➥ p.217)

• In the SECURITY screen, a LOAD LOCK function has

been added, allowing you to disable loading for each

type of file. (➥ p.218)

• In the SECURITY screen, a RECALL LOCK option has

been added, allowing you to lock parameters so that

they will not be changed when a scene or library is

recalled. (➥ p.218)

❏ Input/output functions

• In the OUTPUT PATCH function OUTPUT PATCH

screen, you can now change the patching of output

channels to MIX OUT jacks 1–24. (➥ p.243)

• In the OUTPUT PATCH function INSERT POINT

screen and the INPUT PATCH function INSERT/

DIRECT OUT POINT screen, a SET ALL button and

CLEAR ALL button have been added, allowing you to

turn all channels on/off in a single operation.

(➥ p.246, 281)

• In the OUTPUT PATCH function, a NAME screen has

been added, allowing you to assign names to output

channels for display in various screens (supported from

V1.2). (➥ p.247)

• In the INPUT VIEW function CH JOB screen, channel

settings can now be moved as well as copied. (➥ p.314)

• In the INPUT PATCH function INSERT/DIRECT

OUT POINT screen, PRE ATT has been added as a

direct output transmit location. (➥ p.282)

• In the PAN/ROUTING function MIX SEND VIEW

screen, the send position (PRE/POST) of the signal

sent to the MIX bus is now indicated by the color of the

bar graph. (➥ p.306)

• You can now set a Q of up to 16 for the parametric EQ

in the input channels, output channels, and GEQ

modules.

• You can now set a threshold level of down to –72 dB

for an input channel GATE.

Regarding word clock synchronization

The signal used to synchronize digital audio signal process-

ing is called “word clock.” Normally, one device transmits

a reference word clock signal, and the other devices receive

this word clock signal and synchronize to it.

In order to transmit or receive digital audio signals to or

from an external device via the PM5D/DSP5D’s digital

input/output jacks or via a digital I/O card installed in a

slot, the word clock must be synchronized between the

devices. Be aware that if the word clock is not synchro-

nized, the signals will not be transmitted correctly, and

unpleasant noise will occur.

Hint

• For details on synchronizing the word clock of the PM5D/

DSP5D and external devices, refer to the explanation of

word clock in Operating section “Chapter 4. Connections

and setup” (

➥

p.38), and to the Reference Section “WORD

CLOCK screen” (

➥

p.219).

• As an exception, digital signals that are not synchronized

with the PM5D/DSP5D can be input via a digital I/O card

that contains a sampling rate converter, or via the 2TR IN/

OUT DIGITAL jacks.

How this manual is organized

This owner’s manual is divided into the following three

sections.

❏ Operating section

This section explains the items on the front and rear pan-

els, connections and setup, and how to operate the PM5D’s

basic functionality. In particular if you have not operated a

digital console before, we recommend that you read chap-

ters 2 through 7 first.

❏ Reference section

This section explains the functionality and operation for all

of the PM5D’s screens. Refer to this section when you want

to learn about the items in the screens.

❏ Appendices

This contains various information such as library lists,

parameter lists for the internal effects, the MIDI data for-

mat, and lists of warning messages and error messages.

In this manual, non-locking panel switches that you press

are called “keys,” and those that change their on/off status

when you push them in (locking types) are called

“switches.” Of the control knobs on the panel, those that

turn from a minimum value to a maximum value are

called “knobs,” while those that turn endlessly are called

“encoders.”

Controls located on the panel are enclosed in square brack-

ets [ ] (e.g., [CUE] key, [PAD] switch) in order to

distinguish them from the buttons and knobs displayed in

the screen. For some controls, the section name is listed

before the [ ] (e.g., CH [ON] key, EQ [FREQUENCY]

encoder).

Unless otherwise specified, references to the PM5D apply

to both the PM5D model and the PM5D-RH model. If

specifications differ between the PM5D model and the

PM5D-RH model, such differences will be noted each time

they occur.

Conventions in this manual

2 Top, front, and rear panels

16 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

This chapter explains the names and functions of each part of the PM5D/DSP5D. Details for each

section of the top panel are explained in subsequent chapters of this operating section; refer to the

appropriate chapter for more information.

Top panel

A AD IN section (PM5D model)

In this section you can adjust the sensitivity of the ana-

log signals being input from the rear panel INPUT

jacks 1–48 and ST IN jacks 1–4, and switch pad, insert,

and phantom power (+48 V) on/off (➥ p.43).

B AD IN section (PM5D-RH model)

This area indicates the presence, peak level, and phan-

tom power (+48V) on/off status of the input signal

from rear panel INPUT jacks 1–48 and ST IN jacks 1–

Hint

For the PM5D-RH model, input sensitivity and phantom power

on/off are controlled by operations in the display (

➥

p.44).

C INPUT channel strip section

This section controls the principal parameters for input

channels 1–48 (➥ p.45).

D FADER FLIP/ENCODER MODE section

Here you can select the parameters controlled by the

faders/encoders of the INPUT channel strip (

(➥ p.48).

E MIX section

This section controls the on/off status and send level of

the signals sent from input channels to MIX buses, and

adjusts the master level of the MIX channels (➥ p.57).

F MATRIX section

This section controls the send level of the signals sent

from MIX channels to MATRIX buses, and adjusts the

master level of the MATRIX channels (➥ p.63).

G SELECTED CHANNEL section

In this section you can view and control the mix

parameters for the currently selected input channel or

output channel (➥ p.65).

H Meter section

This section contains peak level meters that indicate

the input levels of input channels and the output levels

of output channels and cue monitoring, as selected by

key operations (➥ p.108).

2 Top, front, and rear panels

(PM5D model)

(PM5D-RH model)

4 5

6 8

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 17

Top, front, and rear panels

I Display

This display shows the information you need to oper-

ate the PM5D, and lets you make system-wide settings

and control mix parameters for input and output

channels (➥ p.23).

Hint

You can adjust the angle of the display by moving the upper

part of the display frame forward or backward.

Note

Before moving the PM5D, you must lower the display all the

way back until it is fastened in place.

J FADER MODE section

Here you can select the combination of channels or

DCA groups that will be controlled by the faders of the

DCA strip section (

K) (➥ p.149).

K DCA strip section

From this section you can control the channels

assigned to DCA groups 1–8 (➥ p.81).

L ST IN/FX RTN (Stereo in / Effect return)

channel strip section

This section controls the principal parameters of ST IN

channels 1–4 or FX RTN channels 1–4 (➥ p.47).

M STEREO strip section

This section controls the principal parameters of the

STEREO A/B channels (➥ p.61).

N SCENE MEMORY section

This section stores/recalls mix parameters as scene

memories (➥ p.88). Mute operations for mute groups

1–8 are also performed in this section (➥ p.83).

O CUE/MONITOR section

This section selects the monitor source that is output

from the MONITOR OUT jacks, and adjusts the lev-

els. This section also determines the cue point and

monitoring method that will be used when you press a

[CUE] key for a channel (➥ p.99).

P OSCILLATOR/TALKBACK section

This section switches the oscillator or talkback on/off,

and adjusts the talkback level (➥ p.105).

Q DISPLAY ACCESS section

This section selects the functions or screen shown in

the display (➥ p.24).

R USER DEFINED KEYS sections

This section executes the functions that have been

assigned to the User Defined keys [1]–[25] (➥ p.148).

S Data entry section

This section lets you move the pointer (the arrow dis-

played in the screen) or cursor (the red frame

indicating a selection) in the display and edit the

parameter value (➥ p.24).

T ASSIGN MODE section

This section lets you assign mute groups and DCA

groups for control from the panel (➥ p.81).

N O P

K M L

2 Top, front, and rear panels

18 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Rear panel

A INPUT jacks 1–48 (PM5D model)

These are balanced XLR-3-31 type input jacks for

inputting analog audio signals from line level devices

or microphones. Nominal input level is

–60 dBu to +10 dBu.

B INSERT IN/OUT jacks 1–48 (PM5D model

only)

These are balanced TRS phone type input/output jacks

for inserting external effects or dynamics processors

etc. into INPUT jacks 1–48. Nominal input/output

level is +4 dBu.

C ST IN (Stereo input) jacks 1–4 (PM5D

model)

These are balanced XLR-3-31 type input jacks for

inputting analog audio signals from line level devices.

Nominal input level is –34 dBu to +10 dBu.

D +48V MASTER switch (PM5D-RH model

only)

This is the master phantom power (+48V) switch for

INPUT jacks 1–48 and ST IN jacks 1–4. If this switch is

off, the +48V buttons shown in the display are

unavailable.

E INPUT jacks 1–48 (PM5D-RH model)

These are balanced XLR-3-31 type input jacks for

inputting analog audio signals from line level devices

or microphones. Nominal input level is

–62 dBu to +10 dBu.

F ST IN (Stereo input) jacks 1–4 (PM5D-RH

model)

These are balanced XLR-3-31 type input jacks for

inputting analog audio signals from line level devices

or microphones. Nominal input level is

–62 dBu to +10 dBu.

3 1

(PM5D model)

Male XLR plug

1 (ground)

2 (hot)

3 (cold)

1/4" TRS

phone plug

Tip (hot)

Ring (cold)

Sleeve (ground)

Male XLR plug

1 (ground)

2 (hot)

3 (cold)

(PM5D-RH model)

Male XLR plug

1 (ground)

2 (hot)

3 (cold)

Male XLR plug

1 (ground)

2 (hot)

3 (cold)

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 19

Top, front, and rear panels

G MIX OUT jacks

These are XLR-3-32 (balanced) jacks that output ana-

log signals such as those that are patched from MIX

channels 1–24. Nominal output level is +4 dBu.

H LAMP connector

This is a four-pin female XLR output jack for supply-

ing power to a gooseneck lamp. (These jacks are

provided at three locations). The location of these jacks

differs between the PM5D model and the PM5D-RH

model.

I MONITOR OUT jacks

These are XLR-3-32 (balanced) jacks that output the

monitor signal selected in the MONITOR section of

the top panel. Nominal output level is +4 dBu.

Note

Although the various output jacks and 2TR IN ANALOG jacks

have a nominal input/output level of +4 dBu (maximum level is

+24 dBu), an internal switch allows this to be changed to

–2 dBu (maximum level +18 dBu) if necessary. For details,

contact your Yamaha dealer.

J CUE OUT jacks

These are XLR-3-32 (balanced) jacks that output the

cue monitor signal from the channel selected by its

[CUE] key. Nominal output level is +4 dBu.

K STEREO OUT A/B jacks

These are XLR-3-32 (balanced) jacks that output the

analog signals of the STEREO A/B channels. Nominal

output level is +4 dBu.

L MATRIX OUT jacks

These are XLR-3-32 (balanced) jacks that output the

analog signals of MATRIX channels 1–8. Nominal out-

put level is +4 dBu.

M DC POWER INPUT connector

This is a connector for connecting the PW800W power

supply. Use the dedicated cable included with the

PM5D to make the connection.

N 2TR IN ANALOG jacks 1/2

These are XLR-3-31 (balanced) jacks that input stereo

analog signals from an external source. Nominal input

level is +4 dBu.

O TIME CODE INPUT jack

This is an XLR-3-31 (balanced) jack that receives

SMPTE time code (LTC) from an external source.

P TO HOST connector

This is a USB (type B) connector that allows communi-

cation with a computer.

Note

PM5D Editor and the USB-MIDI driver required for connection

with your computer can be downloaded from the Yamaha

website listed below.

http://www.yamahaproaudio.com/

Female XLR plug

2 (hot)

1 (ground)

3 (cold)

RLRL

87654321

MJ9KL

Female XLR plug

2 (hot)

1 (ground)

3 (cold)

Female XLR plug

2 (hot)

1 (ground)

3 (cold)

Female XLR plug

2 (hot)

1 (ground)

3 (cold)

Female XLR plug

2 (hot)

1 (ground)

3 (cold)

SMPTE

USB

OUT IN

ON OFF

COAXIAL COAXIALAES/EBU AES/EBU AES/EBU AES/EBU

THRU OUT IN

N X YVUT

Q R S Z aWPO

Male XLR plug

1 (ground)

2 (hot)

3 (cold)

Male XLR plug

1 (ground)

2 (hot)

3 (cold)

2 Top, front, and rear panels

20 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Q GPI connector

This is a D-sub 25-pin female connector that allows

communication with a GPI-equipped external device.

R RS422 REMOTE connector

This is a D-sub 9-pin female connector for remotely

controlling an external device that supports the RS422

protocol.

S HA REMOTE connector

This is a D-sub 9-pin male connector for remotely con-

trolling an external head amp device (e.g., Yamaha

AD8HR or AD824) that supports a special protocol.

T WORD CLOCK IN connector

This is a BNC connector for supplying a word clock

from an external device to the PM5D.

U 75Ω ON/OFF switch

This switch terminates the word clock connection.

Normally you will leave this ON. If a device made by

another manufacturer is connected and word clock

cannot be received correctly, try turning this OFF.

V WORD CLOCK OUT connector

This is a BNC connector for supplying a word clock

from the PM5D to an external device.

W MIDI IN/THRU/OUT connectors

These connectors are used to transmit and receive

MIDI messages to and from external MIDI devices.

The MIDI IN connector receives messages from an

external device, and the MIDI OUT connector trans-

mits messages from the PM5D. Messages received at

the MIDI IN connector are retransmitted without

change from the MIDI THRU connector.

X 2TR OUT DIGITAL (2 track out digital) jacks

1–3

These jacks digitally output the signals of the STEREO

A/B channels. Two types are provided; AES/EBU

(XLR-3-32) jacks (1/2) which output AES/EBU format

signals, and a COAXIAL (RCA phono) jack (3) which

outputs consumer format signals (IEC60958).

Y 2TR IN DIGITAL (2 track in digital) jacks 1–3

These jacks input digital audio from external devices

such as CD players. Two types are provided; AES/EBU

(XLR-3-31) jacks (1/2) which receive AES/EBU format

signals, and a COAXIAL (RCA phono) jack (3) which

receives consumer format signals (IEC60958).

Z CASCADE OUT connector

This is a D-sub half-pitch 68-pin female connector that

can be connected to another PM5D, DSP5D, DCU5D

or DME64N for transmission/reception of control sig-

nals and transmission of audio signals.

a CASCADE IN connector

This is a D-sub half-pitch 68-pin female connector that

can be connected to another PM5D, DSP5D or

DCU5D for transmission/reception of control signals

and reception of audio signals.

b Cooling fan vent

This is the vent for the cooling fans inside the console

(two locations). When placing the unit, take care that

this vent is not obstructed.

c SLOT 1–4

These slots allow separately sold mini-YGDAI I/O

cards to be installed to expand the input/output ports.

Front panel

A MEMORY CARD slot

A memory card inserted in this slot can be used to

save/load scene memories or library data. You can use

PCMCIA Type II flash ATA cards, or CompactFlash

cards inserted into a PC card adaptor.

B MOUSE connector

A PS/2 mouse can be connected to this connector and

used to perform operations in the display.

C KEYBOARD connector

A PS/2 keyboard can be connected to this connector

and used to input text or perform operations in the

display.

D PHONES (Headphone) jack

This headphone jack lets you monitor the MONITOR

OUT or CUE signals.

PHONES

KEYBOARD

MOUSE

MEMORY CARD

PHONES

KEYBOARD

MOUSE

MEMORY CARD

1 2 3 4

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual

Operating section

Top, front, and rear panels

DSP5D front panel

INPUT jacks 1–48 / ST IN (stereo input)

jacks 1–4

These are balanced XLR-3-31 type input jacks for

inputting analog audio signals from line level devices

or microphones. The nominal input level is –62 dBu to

+10 dBu. A resettable head amp is provided on all

jacks, and head amp settings can be stored in scene

memory.

OMNI OUT jacks 1–24

These are XLR-3-32 (balanced) jacks for outputting

analog audio signals. These are used mainly for output-

ting the MIX/MATRIX/STEREO A/B channel signals.

The nominal output level is +4 dBu.

Note

The nominal output level of OMNI OUT jacks 1–24 is +4 dBu

(maximum level is +24 dBu), but if necessary, this can be

changed to –2 dBu (maximum level +18 dBu) by setting an

internal switch (a fee will be charged). For details, please con-

tact your Yamaha dealer.

CASCADE IN/OUT connectors

These are D-sub half-pitch 68-pin female connectors to

allow connection of the DSP5D, PM5D, DCU5D, and

DME64N so that audio signals and control signals can

be transmitted and received.

NETWORK connector

This connector allows the DSP5D to be connected to a

Windows computer via a CAT5 Ethernet cable.

This is used mainly when remotely controlling or edit-

ing the DSP5D from the dedicated “DSP5D Editor”

application software.

Note

• You should use a CAT5 STP (Shielded Twisted Pair) cable

to prevent electromagnetic interference.

• DSP5D Editor and the DME-N Network driver required for

connection with your computer can be downloaded from the

Yamaha website listed below.

http://www.yamahaproaudio.com/

WORD CLOCK IN/OUT connectors

These are BNC connectors used to input and output

word clock signals from and to an external device. The

input connector is terminated with 75 ohms.

CASCADE IN/OUT connectors

These are RJ-45 connectors that can be connected via a

CAT5 Ethernet cable to a DSP5D or DCU5D so that

audio signals and control signals can be transmitted

and received.

Note

• As connectors, use RJ-45 connectors that are compatible

with Neutrik’s etherCON

CAT5.

• As cables, you should use CAT5 STP cables (shielded

twisted pair cables) to prevent electromagnetic interference.

• To prevent electromagnetic interference, use conductive

tape etc. to firmly fasten the metal portion of the connector to

the shield of the cable.

• These connectors use EtherSound technology, but are only

for use with the PM5D system; they cannot be connected to

other EtherSound equipment. For details on the length of

cables that can be used, refer to the following website.

http://www.ethersound.com/technology/compatibility.php

IN/OUT [TX]/[RX] LED

When signals are transmitted (TX) or received (RX) via

the [CASCADE IN]/[CASCADE OUT] connectors, the

corresponding LED will light.

When you use the rear panel mode switch to set the

machine ID, the number of LEDs corresponding to the

machine ID number will light for five seconds

(

➥

p.153).

SLOT 1–2

The input/output ports can be expanded by installing

separately sold mini-YGDAI I/O cards in these slots.

DC POWER INPUT connector

A separately sold PW800W power supply can be con-

nected here as an external backup power supply. Use a

power supply link cable (PSL360) to make this

connection.

POWER LED

This will light if power is being supplied to the DSP5D.

POWER switch

This switch turns the power on/off.

AC IN connector

Use the included power cable to supply power to this

connector.

Grounding screw

For safe operation, be sure that the DSP5D is correctly

grounded. The included power cable has a three-pin

plug, and if the AC outlet is grounded, the DSP5D will

be grounded appropriately. If the AC outlet you’re

using is not grounded, you must be sure to connect

this screw to a valid electrical ground. Correct ground-

ing will effectively eliminate noises such as hum and

interference.

CASCADE IN

OUT OUT

OUT

TX RX TX RX

ININ

75Ω

TERMINATED

OUT OUT

OUT

TX RX TX RX

ININ

75Ω

TERMINATED

1 2

5 64

8 9 L M

7 KJ

2 Top, front, and rear panels

22 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

DSP5D rear panel

A Cooling fan vents

These are the vents for the DSP5D’s internal cooling

fans (two locations). When placing the unit, take care

that these vents are not obstructed.

B FAN switch

This switches the rotational speed of the DSP5D’s

internal cooling fans between HIGH and LOW.

For normal use, set this to LOW. However if the

DSP5D is in a location of high temperature or is out-

side in direct sunlight, set this to HIGH. You should

also set this to HIGH if you feel that the panel is

warmer than usual.

C Mode switch

This switch is used when initializing the settings of

internal memory, when updating the firmware in the

future, and when setting the machine ID number.

D POWER LED

This will light if power is being supplied to the DSP5D.

E Grounding screw

For safe operation, be sure that the DSP5D is correctly

grounded. The included power cable has a three-pin

plug, and if the AC outlet is grounded, the DSP5D will

be grounded appropriately. If the AC outlet you’re

using is not grounded, you must be sure to connect

this screw to a valid electrical ground. Correct ground-

ing will effectively eliminate noises such as hum and

interference.

FAN

HIGH LOW

POWER

FAN

HIGH LOW

POWER

2 3 4

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 23

Basic operation on the PM5D

This chapter explains the various types of user interface used to operate the PM5D.

About the various types of user interface

Basic parameters such as mixing and editing the sound of each channel can be controlled by the faders and encoders of the top

panel. However to make more detailed settings, you will need to access the appropriate “function” and edit the parameter val-

ues in the display. The section below explains the various user interface components shown in the display, and how to use

them.

The user interface in the PM5D’s display uses the follow-

ing components.

❏ Pointer

The arrow shown in the display is called the “pointer.” Use

the pointer to select the parameter you want to control

next.

❏ Cursor

The red frame shown in the display is called

the “cursor.” If the cursor encloses a parame-

ter on the screen, that parameter is selected

for operation.

❏ Tabs

The screen names shown in

the upper left of the display

are called “tabs.” Tabs are

used to switch between

screens within the same

function.

❏ Buttons

Buttons in the display are

used to switch parameters

on/off or to select one of

multiple choices. Buttons

that are currently on are dis-

played in green (some

buttons are displayed in red

or blue); buttons that are

turned off are displayed in

gray.

❏ Knobs/Faders/Boxes

Knobs/faders in the display are used to edit parameter val-

ues. The current value is shown in the box. Boxes for which

/ buttons are displayed at left and right allow you to

edit the parameter by using these buttons. (If editing is not

possible, the buttons will be gray.)

If you want to assign a name to a channel or scene, input

characters, numerals, and symbols into the box.

❏ Character palette

This is a “virtual” keyboard used to input characters,

numerals, and symbols into a text input box.

3 Basic operation on the PM5D

User interface in the display

Cursor

Ta b

Buttons turned

off (gray)

Buttons turned

on (green)

Fader

Box

Knob

/ buttons for

editing the value

Basic operation on the PM5D

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual

Operating section

❏

Scroll bar

If the displayed items are too numerous to fit into a single

screen, you can use the scroll bar to view the portion that is

not currently displayed.

The DISPLAY ACCESS section contains keys that access

the desired function or screen in the display.

Global functions

These keys access functions that affect the entire

PM5D.

Output functions

These keys access functions that are related to output

channels.

Input functions

These keys access functions that are related to input

channels.

When you press the key for the desired function, the screen

for that function will appear in the display. By repeatedly

pressing a key you can cycle through the screens included

in that function.

Hint

If you hold down the [SHIFT] key and press a key in the DIS-

PLAY ACCESS section, the screens included in that function

will appear in the reverse order (Previous Tab function). You

can also use the Previous Tab function by holding down a key

in the DISPLAY ACCESS section. If you rapidly press a key

twice, you will return to the first screen in that function.

Controllers used to edit settings and values in the display

are gathered into the data entry section.

[DEC/CANCEL]/[INC/OK] keys

Use these keys to increase or decrease the value of the

parameter where the cursor is located. If the PM5D has

displayed a window asking you to confirm an opera-

tion such as recall or store, these buttons can be used

instead of the CANCEL button and OK button shown

in the window.

CURSOR [

√

]/[

†

] keys

These keys are used to move the cursor to the desired

parameter.

[SHIFT] key

This key can be used in conjunction with the CUR-

SOR [

√

]/[

†

] keys to move the cursor

rapidly, or in conjunction with the [DATA] encoder or

[DEC]/[INC] keys to change the parameter value

rapidly.

If you hold down the [SHIFT] key and press the

[ENTER] key, the JOB SELECT window will appear,

allowing you to set multiple parameters in a single

operation. (When you move the cursor to a parameter

for which there is a JOB SELECT window, an indica-

tion of “Job Select = [SHIFT] + [ENTER]” will

appear.)

[ENTER] key

Use this key to switch a button at the cursor location

on/off, or to open a window.

[DATA] encoder

Use this to increase or decrease the value of the param-

eter where the cursor is located. The parameter value

will change more rapidly if you turn the [DATA]

encoder while holding down the [SHIFT] key.

Scroll bar

DISPLAY ACCESS section

Data Entry section

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 25

Basic operation on the PM5D

F Track pad and left/right buttons

These are used to move the pointer or select the desired

parameter. To adjust a knob-type parameter in the dis-

play, hold down the left button or right track pad

button while you operate the track pad.

G PHONES (Headphone) jack

This is a stereo phone jack for connecting a set of

headphones.

If desired, you can add the following external user inter-

face components.

❏ Mouse

A PS/2 compatible mouse can be connected to the MOUSE

connector located on the front panel of the PM5D and

used in the same way as the track pad.

❏ Keyboard

A PS/2 compatible keyboard can be connected to the KEY-

BOARD connector located on the front panel of the PM5D

and used in the same way as the character palette in the

display to input characters, numerals, and symbols. The

numeric key pad of the keyboard can be used to input

numerical values or to recall scenes.

Each key (or combination of keys) has the following

function.

Full keyboard

Numeric key pad

External user interface

Key Function

Same function as the [INS/OK] key of the Data

Entry section

Same function as the [DEC/CANCEL] key of

the Data Entry section

<←>, <→>,

<↑>, <↓>

Same function as the CURSOR [√]/[®]/[π]/

[†] keys

<Alt> +

Same function as moving the [DATA] encoder

clockwise

<Alt> +

Same function as moving the [DATA] encoder

counterclockwise

<Enter> Same function as the [ENTER] key

<Shift> Same function as the [SHIFT] key

<Ctrl> + <←>,

Same function as the buttons of the

character palette

Copies the text string in the box and clears the

copy-source character string (Cut)

Same function as the COPY button of the

character palette

Same function as the PASTE button of the

character palette

Same function as the INS button of the char-

acter palette

Same function as the DEL button of the char-

acter palette

<Home>

Moves the input location in the box to the

beginning

<End>

Moves the input location in the box to after the

last-input character

Deletes the preceding character that was

input in the box (Backspace)

<Tab>

Switches to the next screen within the same

function

Switches to the previous screen within the

same function

<Esc>

Accesses the function menu (if the function

menu is already displayed, recalls the last-dis-

played screen)

<Alt> +

<0>–<9>

Switch screens within the same function

Key Function

<0>–<9>

Input a scene number (if the PREFERENCE 1

screen item USE NUMERIC-KEYPAD is on),

input numerical values (if off)

<.>

Returns the scene selection number to the

number of the scene that was last recalled or

stored

<+>

Same function as the [π] key of the SCENE

MEMORY section

<->

Same function as the [†] key of the SCENE

MEMORY section

</>, <*> Not used

<Enter>

Same function as the [RECALL] key of the

SCENE MEMORY section (if the PREFER-

ENCE 1 screen item USE NUMERIC-KEY-

PAD is on), same function as the [ENTER] key

(when off)

Key Function

3 Basic operation on the PM5D

26 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Basic operation

This section explains the basic procedures you can perform in the PM5D’s display. In general, you will perform operations in

the PM5D’s display by combining the operations described here.

Moving the pointer to a specific parameter in the screen

and pressing the left/right track pad button (or the left/

right mouse button) is called “clicking.” Clicking is mainly

used to turn an on-screen button on/off, to move the cur-

sor, or to make fine adjustments to a value.

Using the CURSOR [√]/[®]/[π]/[†] keys of the data

entry section to move the cursor to a desired parameter

and then pressing the [ENTER] key is equivalent to click-

ing. If you are using a PS/2 keyboard, you can perform the

same action using the arrow keys and the <Enter> key.

Subsequently in this manual, this operation will simply be

called “clicking.”

Hint

When using the track pad, you can

move the pointer to the desired param-

eter and then tap the track pad to

obtain the same result as if you

pressed the left button. (This is called

the Tapping function.) If you want to

use the tapping function, you must

enable it in the PREFERENCE 2

screen (UTILITY function) (

➥

p.206).

Moving the pointer to a specific parameter in the screen

and then holding down the left/right track pad (or mouse)

button while moving up/down/left/right is called “drag-

ging.” Dragging is used mainly to adjust the value of a

knob or fader.

Using the CURSOR [√]/[®]/[π]/[†] keys of the data

entry section to move the cursor to a desired parameter

and then turning the [DATA ] encoder (or pressing the

[DEC/CANCEL]/[INC/OK] keys) is equivalent to drag-

ging. If you are using a PS/2 keyboard, you can perform the

same action using the arrow keys and the <PageUp>/

<PageDown> keys (or keys that have the same function).

Subsequently in this manual, this operation will simply be

called “dragging.”

Moving the mouse pointer to a specific parameter in the

screen, dragging to another location in the screen, and then

releasing your finger is called “dragging and dropping.”

Dragging and dropping is used to copy EQ or compressor

settings to another channel. Dragging and dropping can-

not be performed using the CURSOR keys or keyboard.

Subsequently in this manual, this operation will be called

“dragging and dropping.”

Click

• Track pad • Mouse

• Track pad

Tapping

Drag

While pressing

• Track pad • Mouse

Drag and drop

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 27

Basic operation on the PM5D

A desired function/screen can be accessed in the display

using either of the following two methods.

❏ Using the keys of the DISPLAY ACCESS

section

From the keys of the DISPLAY ACCESS section,

press the key corresponding to the desired

function.

The most recently operated screen for that function

will appear.

If you want to switch to another screen within

that function, press the same key you pressed

in step 1.

If you repeatedly press a key in the DISPLAY ACCESS

section, or hold down the [SHIFT] key of the data

entry section and press the same key as in step 1, you

will return to the preceding screen of the same

function.

❏ Using buttons within the display

In any screen, click the function name area

located in the upper left of the screen.

When you click the function name area, the function

menu screen will appear. This screen is the starting

point from which you can access the desired screen via

operations in the display.

In the function menu screen, click the button

corresponding to the desired function.

The most recently operated screen for that function

will appear.

Click a tab in the screen to select the desired

screen.

Hint

By clicking the buttons located below

the function name area you can switch backward through the

screens that had been previously displayed for at least two

seconds (not including the function menu). Up to the eight

most recent screens are remembered.

To select a parameter, use the data entry section’s control-

lers or a PS/2 keyboard to move the cursor (the red frame).

Hint

If you are using a mouse or the track pad, the cursor will move

when you click on the button or knob of the desired

parameter.

Use the CURSOR [√]/[®]/[π]/[†] keys to

move the cursor.

The cursor in the display will move in the direction of

the key you pressed. However, it will not move if there

is no parameter in the direction of that key.

Accessing a desired screen

Click the function name area

Click a tab

Moving the cursor

Move to the adjacent grid

3 Basic operation on the PM5D

28 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

To move quickly to the outer edge of the cur-

rent window or to a different window, hold

down the [SHIFT] key and use the CURSOR

[√]/[®]/[π]/[†] keys.

You will move from the scroll window in which the

cursor is currently located, in the direction of the key

you pressed.

Hint

If the cursor is located on a grid such as in a PATCH screen,

turning the [DATA] encoder clockwise will move the cursor

toward the right, and turning it counterclockwise will move the

cursor toward the left. If you are holding down the [SHIFT]

key, turning the [DATA] encoder clockwise will move the cur-

sor downward, and turning it counterclockwise will move the

cursor upward.

A scroll bar is displayed if there are more items than can be

shown in a single screen. To scroll the screen, drag the box

shown in the bar.

You can also scroll the screen by clicking the vacant por-

tion of the scroll bar or the / buttons or /

buttons located at the ends of the scroll bar.

If you move the cursor to the scroll bar

and press the [DEC/CANCEL] key or

turn the [DATA] encoder counterclock-

wise, the screen will scroll toward the left

(or upward, in the case of vertical scroll-

ing). If you press the [INC/OK] key or

turn the [DATA] encoder clockwise, the screen will scroll

toward the right (or downward, in the case of vertical

scrolling).

Hint

If the cursor is located at the scroll bar box, holding down the

[SHIFT] key and turning the [DATA] encoder will have the

same result as clicking the button or button, depend-

ing on the direction in which you turn the encoder.

[SHIFT] key

CURSOR [®] key

Scrolling the screen

➠

Drag

Click these buttons to move the

scroll bar box step-wise in the

direction indicated. Clicking the

/ buttons will move in larger

steps than clicking the /

buttons.

Click in these areas to

make the scroll bar box

move by a large step in the

corresponding direction;

the screen will scroll

accordingly.

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 29

Basic operation on the PM5D

Buttons in the display are used to switch parameters on/off

or to select one of multiple choices.

Move the pointer to the desired button, and

use the left/right buttons of the track pad (or

mouse) to click the button.

The button will be switched on/off (or the correspond-

ing button will be selected).

Hint

You can use the CURSOR [

√

]/[

†

] keys and the

[ENTER] key (or the arrow keys and <Enter> key of a PS/2

keyboard) to perform the equivalent operation.

Hint

When using the track pad, you can also click by tapping the

track pad if you have enabled tapping in the PREFERENCE 2

screen (UTILITY function

➥

p.206). In this case, the result will

be the same as if you pressed the left button of the track pad

(or mouse).

Knobs and faders in the display are used to adjust the value

of specific parameters.

Move the pointer to the desired knob/fader,

and use the left/right buttons of the track pad

(or mouse) to click the knob/fader.

The cursor will move to that location.

To increase or decrease the value in steps of 1,

click the right button or left button of the

track pad (or mouse).

Clicking the right button will raise the value by one

step, and clicking the left button will lower the value by

one step.

To raise or lower the value continuously, use

the track pad (or mouse) to drag the knob/

fader.

The value will change as you drag the knob or fader

left/right or up/down. For a parameter whose knob has

a wide range of adjustment, holding down the right

button of the track pad (or mouse) as you drag will

produce a larger range of change than when using the

left button.

Hint

You can also adjust the value by using the [DEC/CANCEL]/

[INC/OK] keys, the [DATA] encoder, or the <PageUp>/<Page-

Down> keys of a PS/2 keyboard. When adjusting a parameter

that has a wide range of adjustment, you can increase the rate

of change by holding down the [SHIFT] key while you press

the [DEC/CANCEL]/[INC/OK] keys (or turn the [DATA]

encoder).

Operating the buttons

➠

Click

Off On

Adjusting the setting of a knob or

fader

Adjust the

knob value

Adjust the

fader value

3 Basic operation on the PM5D

30 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

On the PM5D you can assign a four-character name to

each input channel or DCA group, and assign a title to

scene and library data when saving it.

For example, the screen shown below is the LIBRARY

STORE window that appears when you assign a name to

the INPUT EQ library. To input characters in this screen,

use the following procedure.

Use the character palette (or a PS/2 key-

board) to input a character.

When you click the character palette, a character will

be input in the box, and the highlighted area will move

to the right.

Input the subsequent characters in the same

way.

When inputting characters, you can use the following

buttons in the character palette.

Note

Copy/paste operations are not possible in some screens.

There are also cases in which the paste operation cannot be

performed due to the type of character string copied to the

buffer memory.

When you have finished inputting the name,

click the STORE button.

The name you input will be stored.

Hint

• In general, the same procedure applies in screens where

you enter names for scenes or other library items.

• If a PS/2 keyboard is connected, you can use it to enter

characters.

• If you move the cursor to the text input box and press the

[ENTER] key (or click), the input position will move to that

point. If the cursor is located at the text input box, you can

step through the available characters by turning the [DATA]

encoder. If the cursor is located elsewhere, turning the

[DATA] encoder will move the selected position. The [INC]/

[DEC] keys move the selected position regardless of where

the cursor is located.

Note

The number of characters that can be input will depend on the

type of data (scene/library) you are saving. You cannot input

more than the specified number of characters, or move the

highlighted area beyond that range.

INS button

Inserts a space (blank) at the high-

lighted position. Pressing the

<Insert> key of a PS/2 keyboard will

produce the same result.

DEL button

Deletes the character at the high-

lighted position. Pressing the

<Delete> key of a PS/2 keyboard will

produce the same result.

CLEAR button

Deletes all characters that have been

input in the text input box.

buttons

Move the highlighted area to left or

right.

PASTE button

Pastes the character string that was

copied to buffer memory by the

COPY button. Holding down the

<Ctrl> key and pressing the <V> key

of a PS/2 keyboard will produce the

same result.

COPY button

Copies the character string in the box

to a temporary buffer memory. Hold-

ing down the <Ctrl> key and pressing

the <C> key of a PS/2 keyboard will

produce the same result.

CAPS LOCK button

Switches between uppercase and

lowercase alphabetical characters.

Uppercase characters can be input

while this button is on.

Assigning a name

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 31

Connections and setup

This chapter describes examples of expanded systems using the DSP5D, audio input/output con-

nections, and the setup that will be necessary when starting up the PM5D/DSP5D for the first time.

Examples of systems expanded with the DSP5D

• In order to use “cascade connections” for expansion, you must first specify the machine ID (➥ p.153) and make cascade

connection settings (➥ p.154). If the PM5D and DSP5D are cascade-connected, you’ll be able to select the PM5D/DSP5D

that will be the target of control from the PM5D’s panel (➥ p.40).

• This system expands the number of input channels to

96 monaural + 8 stereo.

• To make cascade connections, use a D-sub half-pitch

68-pin cable to connect the CASCADE IN connector to

the OUT connector of each respective PM5D and

DSP5D unit.

• The connection between the PM5D located at FoH and

the DSP5D located on the stage is routed through the

DCU5D, via Ethernet CAT5 cable and the CASCADE

IN and OUT connectors.

• By using two DSP5D units, the number of input chan-

nels is expanded to 144 monaural + 12 stereo.

• To make cascade connections between the PM5D and

DCU5D, use D-sub half-pitch 68-pin cables to con-

nect the CASCADE IN connectors to the OUT

connectors of each respective unit.

• Connections between the two DSP5D units are made

using an Ethernet CAT5 cable and a D-sub half-pitch

68-pin cable, each connected from CASCADE IN to

OUT of the two units.

Note

If the PM5D and DSP5D are cascade-connected via the

DCU5D and you’re not synchronizing to an external word

clock being input to the PM5D, you should set the PM5D as

the word clock master and the DSP5D as the slave.

4 Connections and setup

Example of simple input expansion

(PM5D + one DSP5D unit)

FoH

CASCADE

PM5D

OUTINOUTIN

DSP5D

CASCADE IN

PM5D + remotely connected input

expansion

(PM5D + DCU5D + two DSP5D units)

Stage

FoH

DSP5D DSP5D

DCU5D

POWER

CASCADE

OUT

CASCADE IN CASCADE IN

Ethernet CAT5

Ethernet

CAT5

OUT

PM5D

Connections and setup

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual

Operating section

• One DSP5D unit is connected to a PC via an Ethernet

CAT5 cable, allowing the DSP5D to be controlled from

DSP5D Editor.

Control from DSP5D Editor

(one DSP5D unit + PC)

DSP5D PC

CASCADE IN

Ethernet CAT5

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 33

Connections and setup

Audio connections

PM5D model

INPUT jacks 1–48 are used mainly to connect micro-

phones or monaural line-level devices. ST IN jacks 1–4 are

used mainly to connect stereo line-level devices.

Input signal sensitivity, pad on/off, and phantom power

(+48V) on/off are controlled from the top panel AD IN

section (➥ p.44).

PM5D-RH model

INPUT jacks 1–48 and ST IN jacks 1–4 can both be used to

connect microphones or line-level devices.

Input signal sensitivity and phantom power (+48V) on/off

are controlled from within the display (➥ p.44). However,

all phantom power can be switched on/off as a whole by

the rear panel [+48V MASTER] switch.

DSP5D

INPUT jacks 1–48 and ST IN jacks 1–4 will accommodate

connections ranging from microphones to line level

devices.

Each connector is provided with phantom power (+48V),

and the input signal sensitivity and phantom power on/off

can be operated from the display as on the PM5D-RH

(➥ p.44). The +48V master switch is turned on/off in the

SYS/W.CLOCK function MIXER SETUP screen

(➥ p.221).

Analog audio connections

Synthesizer Microphone

Effect processor

Synthesizer

MicrophoneMicrophone

When the PM5D, PM5D-RH, or DSP5D are in the

default state, the input signal from INPUT jacks 1–48 is

patched to input channels 1–48, and the input signal

from ST IN jacks 1–4 is patched to the ST IN channels.

However, you may change this if desired (for details on

restoring the default patching ➥ p.40).

SynthesizerMicrophone

4 Connections and setup

34 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

PM5D/PM5D-RH

MIX OUT jacks 1–24, MATRIX OUT jacks 1–8, and STEREO OUT A/B jacks respectively output the signal from MIX chan-

nels 1–24, MATRIX channels 1–8, and the STEREO A/B channels.

The MONITOR OUT jacks output the monitor signal that is selected in the top panel MONITOR section.

The CUE OUT jacks output the cue monitor signal of the channel that is currently selected by its [CUE] key.

Analog output connections

RLRL

87654321

MIX OUT MATRIX OUT

MONITOR OUT DC POWER INPUTCUE OUT

STEREO OUT

Monitor speakers Monitor speakers

PW800W power supply

Monitor speakers

(foldback)

Main speakers

Recorder, relay

vehicle, etc.

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 35

Connections and setup

DSP5D

With the default settings, the signals of MIX channels 1–22 are output from OMNI OUT jacks 1–22, and the signals of the

STEREO A channel are output from OMNI OUT jacks 23–24. The desired output signal can be patched to each jack; the sig-

nals of MIX channels 1–24, MATRIX channels 1–8, STEREO A/B channels, or cue signals can be output from OMNI OUT

jacks 1–24.

CASCADE IN

OUT OUT

OUT

TX RX TX RX

ININ

75Ω

TERMINATED

Main speakers

Monitor speakers

(foldback)

PW800W power supply

(for backup external power supply)

4 Connections and setup

36 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

PM5D/PM5D-RH

Use 2TR IN DIGITAL jacks 1–3 to connect digital sources

such as CD players or DAT recorders. (To input analog

output signals from a CD player or DAT recorder, use 2TR

IN ANALOG jacks 1/2.)

Use 2TR OUT DIGITAL jacks 1–3 to send the STEREO A/

B channel signals to a DAT recorder or other digital device.

By installing separately sold mini-YGDAI I/O cards in slots

1–4 (1–2 on the DSP5D) you can add analog input/output

jacks to the PM5D/DSP5D or allow connection of digital

devices such as digital MTR or HDR units.

The following types of I/O card can be used.

For the most recent information regarding I/O cards, refer

to the following Yamaha website.

http://www.yamahaproaudio.com/

Note

• In order to send or receive digital audio via the 2TR IN DIGI-

TAL jacks, 2TR OUT DIGITAL jacks, or slots 1–4, the word

clock data of the respective signals must be synchronized

(

➥

p.38).

• In order to assign input signals from the 2TR IN DIGITAL

jacks, 2TR IN ANALOG jacks, or slots 1–4 to input channels

or ST IN channels, you will need to change the input patch-

ing (

➥

p.74).

Digital input/output connections

SMPTE

USB

OUT IN

ON OFF

COAXIAL COAXIALAES/EBU AES/EBU AES/EBU AES/EBU

THRU OUT IN

DAT

00.00.00.00

2TR IN

ANALOG

2TR OUT

DIGITAL

2TR IN

DIGITAL

SLOT

CD player DAT recorder

Digital MTR/HDR

Digital I/O card

Card type Model

Number of

channels

Digital

format

Bit

depth

AD card

MY4-AD 4

— 24 bit

MY8-AD*

8MY8-AD24

MY8-AD96

DA card

MY4-DA 4

—

20 bit

MY8-DA96 8 24 bit

AD/DA card MY8-ADDA96 8 — 24 bit

Digital I/O card

MY8-AE

AES/EBU

24 bit

MY8-AEB

MY8-AE96

MY8-AE96S

MY16-AE 16

MY8-AT 8

ADAT

MY16-AT 16

MY8-TD 8

TASCAM

MY16-TD 16

CobraNet card

MY16-C*

16 CobraNet 24 bit

MY16-CII

AVIOM

Yamaha output

card

AVIOM16/o-Y1 16 A-NET 24 bit

AudioService

MADI card

MY16MADI64 16 MADI 24 bit

AuviTran

EtherSound

card

AVY16-ES 16 EtherSound 24 bit

Waves plug-in

DSP card

Y96K* 8 ADAT 24bit

* is supported only by the PM5D.

Card type Model

Number of

channels

Digital

format

Bit

depth

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 37

Connections and setup

Before installing a card, you must check the Yamaha web-

site to make sure that this device is compatible with this

card, and to verify the number of cards that can be

installed in conjunction with other Yamaha or third-party

cards.

Yamaha website: http:www.yamahaproaudio.com

To install an optional mini-YGDAI card, proceed as

follows.

Make sure that the power is turned off.

Loosen the screws that hold the slot cover in

place, and remove the slot cover.

Keep the removed slot cover in a safe place.

Align the edges of the card with the guard

rails inside the slot, and insert the card into

the slot.

Push the card all the way into the slot so that the con-

nector at the end of the card is correctly mated with the

connector inside the slot.

Use the screws included with the card to fas-

ten the card in place.

Malfunctions or incorrect operation may occur if the

card is not fastened.

Installing an option card

COAXIAL

AES/EBU

AES/EBU AES/EBU

COAXIAL

AES/EBU

4 Connections and setup

38 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Word clock connections and settings

This section explains the word clock settings required in order to send or receive digital audio between the PM5D/DSP5D and

an external digital device.

When digital audio signals are being sent or received

between multiple devices, the devices must process the

audio signals at the matching timing. For example if the

audio signal processing is not synchronized, the signals will

not be transmitted correctly and unpleasant noise will

occur even if both devices are set to the same sampling

frequency.

The signal used to synchronize digital audio signal process-

ing is called “word clock.” Normally, one device transmits

a reference word clock signal, and the other devices receive

this word clock signal and synchronize to it. (The transmit-

ting device is called the “word clock master” and the

receiving devices are called “word clock slaves.”)

The word clock can be synchronized between the PM5D/

DSP5D and external devices in either of two ways; you can

send/receive a word clock signal by itself, or use the clock

data that is included in a digital audio signal.

The WORD CLOCK IN/OUT connectors on the rear

panel of the PM5D (front panel for the DSP5D) are used to

send/receive a word clock signal by itself. In general, word

clock connections can be made in either of the following

two ways.

Using daisy-chain connections

In this method, the signal is distributed sequentially; the

WORD CLOCK OUT connector of the first device is con-

nected to the WORD CLOCK IN connector of the second

device, and so on. Turn all of the PM5D’s 75Ω ON/OFF

switches ON. On the DSP5D, this is fixed at 75Ω ON. This

method is not recommended for large systems.

Using a word clock distribution box

In this method, a special word clock distribution box is

used to distribute the signal from the word clock master to

multiple word clock slaves. Turn ON all of the 75Ω ON/

OFF switches.

If an external device does not have WORD CLOCK IN/

OUT connectors, the clock data included in the digital

audio signal is used. In this case, both the digital audio sig-

nal and the clock data are sent from the DIGITAL OUT

jack of the word clock master to the DIGITAL IN jack of

the word clock slave.

When digitally connecting the PM5D/DSP5D to an exter-

nal device, you must select the source that will be the word

clock master for the system.

Repeatedly press the [SYS/W.CLOCK] key of

the DISPLAY ACCESS section until the WORD

CLOCK screen appears.

In this screen you can select the master clock, and

check the input signal synchronization status for each

slot or jack.

Note

When you switch the word clock source, noise may occur due

to loss of synchronization. You must lower the level of your

monitoring equipment before you perform the following

operation.

Use the MASTER CLOCK SELECT area located in the

upper part of the screen to select the master clock

source. You can choose one of the following sources.

About word clock

WC IN

(BNC)

WC OUT

(BNC)

WC OUT (BNC)

WC IN

(BNC)

WC IN

(BNC)

WC OUT

(BNC)

75Ω ON/OFF= ON

75Ω ON/OFF= ON 75Ω ON/OFF= ON 75Ω ON/OFF= ON

Word clock

master

Device A

Word clock

slave

Device B

Word clock

slave

Device C

Word clock

slave

WC OUT

(BNC)

WC IN (BNC) WC IN (BNC) WC IN (BNC) WC IN (BNC)

75Ω ON/OFF= ON

75Ω ON/OFF= ON 75Ω ON/OFF= ON75Ω ON/OFF= ON 75Ω ON/OFF= ON

Word clock

master

Device A

Word clock

slave

Word clock

distribution box

Device B

Word clock

slave

Device C

Word clock

slave

Device D

Word clock

slave

DIGITAL

OUT

DIGITAL

Digital audio signal

Clock data

Device A

Word clock

master

Device B

Word clock

slave

Selecting the word clock master

WORD CLOCK MASTER CLOCK SELECT area

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 39

Connections and setup

PM5D

DSP5D

Note

• Sources for which the symbol at the left of the button is

red (UNLOCK) or yellow (UNKNOWN) cannot be selected,

since a valid clock is not being input or the clock cannot be

detected.

• If the PM5D and DSP5D are cascade-connected via the

DCU5D and you’re not synchronizing to an external word

clock being input to the PM5D, you should set the PM5D as

the word clock master and the DSP5D as the slave. This

means that in this case, you’ll select INT for the PM5D, and

CASCADE IN for the DSP5D.

In the MASTER CLOCK SELECT area located in

the upper part of the screen, click a button to

select the desired master clock source.

A window will appear, asking you to confirm that you

want to switch the master clock.

Click the OK button.

The selected word clock master will be enabled. The

selected word clock master is remembered even if you

turn off the power. As long as the connections have not

been changed, you don’t have to make this setting

again.

Note

• If a digital I/O card (such as the MY8-AE96S) that contains a

built-in SRC (Sampling Rate Converter) is installed in slots,

you can switch the SRC on/off in groups of two channels.

The input signals from channels for which the SRC is turned

on do not need to be synchronized with the PM5D/DSP5D’s

word clock.

• If transferring high sampling rate (88.2 kHz/96 kHz) signals

between the PM5D/DSP5D and an external device, you will

need to select the transmission method. (For details, refer to

p.220)

INT 96, INT 88.2,

INT 48, INT 44.1

These settings select the PM5D’s inter-

nal clock. If you select one of these set-

tings, the PM5D will operate as the

word clock master. As necessary,

make settings within your external

devices so that they will operate as

word clock slaves.

W.CLOCK IN

The PM5D will follow the word clock

signal being input from the rear panel

WORD CLOCK IN connector.

CASCADE IN

The PM5D will follow the clock data

being sent from another PM5D con-

nected to the CASCADE IN connector.

2TR IN D1–D3

The PM5D will follow the clock data

included in the input signal from 2TR

IN DIGITAL jacks 1–3.

SLOT 1–4

The PM5D will follow the clock data

included in the input signal from a digi-

tal I/O card installed in slots 1–4. (You

can select a speciﬁc pair of adjacent

odd-numbered/even-numbered chan-

nels.)

INT 96, INT 88.2,

INT 48, INT 44.1

These settings select the DSP5D’s

internal clock. If you select one of these

settings, the DSP5D will operate as the

word clock master. As necessary,

make settings within your external

devices so that they will operate as

word clock slaves.

W.CLOCK IN

The DSP5D will follow the word clock

signal being input from the front panel

WORD CLOCK IN connector.

CASCADE IN

(D-sub half-pitch

68-pin connector)

The DSP5D will follow the clock data

sent from the other DSP5D, the PM5D,

or the DME64N.

CASCADE IN

(RJ-45 connector)

The DSP5D will follow the clock data

sent from the other DSP5D or the

DCU5D.

SLOT 1–2

The DSP5D will follow the clock data

included in the input signal from a digi-

tal I/O card installed in slots 1–2. (You

can select a speciﬁc pair of adjacent

odd-numbered/even-numbered chan-

nels.)

4 Connections and setup

40 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Restoring the current scene to the default state

When the PM5D/DSP5D is in its default state, the input

signals from INPUT jacks 1–48 are patched to input chan-

nels 1–48 and the input signals from ST IN jacks 1–4 are

patched to the ST IN channels, and can then be output via

the STEREO bus or MIX buses.

However, if the PM5D/DSP5D’s internal mix parameter

settings (referred to as the “current scene”) have been

modified, the signal of a specific input may not be sent to

an input channel, or the EQ or dynamics processors may

be set to produce extreme effects.

To initialize the mix parameters from such a state, proceed

as follows.

Use the SCENE [π]/[†] keys of the SCENE

MEMORY section to make the scene number

indicator show “000”.

Scene number “000” is a scene memory containing the

default settings.

Hint

If the PM5D and DSP5D are cascade-connected, scene data

is stored in both the PM5D and the DSP5D.

When a scene is recalled, the same scene number is recalled

on all PM5D/DSP5D units.

Press the [RECALL] key of the SCENE MEM-

ORY section.

Scene number “000” will be loaded, and the current

scene will return to the default state.

Note

Be aware that when scene number “000” is loaded, the input

patch, output patch, internal effect, and HA (Head Amp) set-

tings will also return to their default state. (However, the word

clock master selection is not affected.)

Switching the target of panel operations (when cascade-con-

nected with the DSP5D)

When the DSP5D is cascade-connected, you can switch the

target of operations performed from the PM5D’s panel,

and operate these units while seamlessly switching between

the PM5D and DSP5D.

To switch the target of panel operations, use the following

procedure. For details, refer to the page reference given for

each step.

Set the machine ID number of the PM5D and

DSP5D (➥ p.153).

In the SYS/W.CLOCK function MIXER SETUP

screen, make settings for cascade connections

(➥ p.154).

Use one of the following three methods to

switch the target of panel operations.

• Using the constantly-displayed screen

In the constantly displayed screen, select the machine

ID and change it (➥ p.164).

• Using a user-defined key

In the UTILITY function USER DEFINE screen, assign

the DSP5D CONTROL function (➥ p.148), and use

the user-defined key to switch the target of control

(➥ p.149).

• Using the FADER MODE key

In the UTILITY function FADER ASSIGN screen,

assign a DSP5D layer (➥ p.149), and use the FADER

MODE key to switch the target of control (➥ p.150).

Scene number

indicator

SCENE [π]/[†]

keys

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 41

Input channel operations

This chapter explains the functions and operation of each section related to input channels.

About the input channels

The input channel section processes the signals that are input via the input patch section, and outputs them to the STEREO

buses or MIX buses. There are three types of input channel, as follows.

Input channels 1–48

These channels are used to process monaural signals. When the input patching is in the default state, the input signals from

INPUT jacks 1–48 are assigned to these channels.

ST IN channels 1–4

These channels are used to process stereo signals. When the input patching is in the default state, the input signals from ST IN

jacks 1–4 are assigned to these channels.

5 Input channel operations

42 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

FX RTN channels 1–4

These channels are used mainly to process the return signals (stereo) from the internal effects. When the input patching is in

the default state, the left/right channels of internal effects 1–4 are assigned to these channels.

• INPUT PATCH

This assigns an input signal to the input channel.

•ø (Phase)

Switches the phase of the input signal.

• MS DECODE (Input channels / ST IN channels

only)

Switches MS decode processing on/off when an MS

mic is connected.

• ATT (Attenuator)

Attenuates/boosts the level of the input signal.

• HPF (High Pass Filter)

This is a high pass filter that cuts the region below the

specified frequency.

•4 BAND EQ (4 band equalizer)

A parametric EQ with four bands; HIGH, HIGH MID,

LOW MID, and LOW.

• GATE (Input channels and ST IN channels only)

This is a dynamics processor that can be used for gat-

ing or ducking.

• COMP (Compressor) (Input channels and ST IN

channels only)

This is a dynamics processor that can be used as a com-

pressor, expander, or limiter.

• INPUT DELAY (Input channels and ST IN channels

only)

This delays the input signal. It can be used to make fine

adjustments in the relative timing between channels.

• LEVEL/DCA 1-8

Adjusts the input level of the effect.

• ON (On/off)

Turns the input channel on/off. If off, that channel is

muted.

• PAN

Adjusts the panning of the signal sent from the input

channel to the STEREO bus. If necessary, this pan set-

ting can also be applied to signals sent to two paired

MIX buses.

• LCR (Left/Center/Right)

Sends the three-channel signal (left/right channels and

a center channel) to the STEREO bus.

• MIX 1-24 (Mix send level 1–24)

Adjusts the send level of the signal sent from the input

channel to MIX buses 1–24. As the position from

which the signal is sent to the MIX bus, you can choose

from the following; immediately before the 4-band EQ,

pre-fader, or post-fader.

• INSERT (Input channels and ST IN channels only)

Here you can patch the desired output port and input

port to insert-out/insert-in, allowing an external effect

processor or other device to be inserted. You can

switch the insert-out and insert-in locations.

• DIRECT OUT (Input channel and ST IN channels

only)

This can be patched to an output port, and the input

signal sent directly from that output port.

• METER

This meters the level of the input channel. The level

detection point can be switched.

Note

The signal assignments from input patch to input channel can

be edited in the INPUT PATCH function INPUT PATCH

screen.

To edit the parameters of an input channel, you can either

use the panel controllers (e.g., INPUT channel strip, ST

IN/FX RTN channel strip, SELECTED CHANNEL sec-

tion), or access the appropriate screen in the display and

edit the parameters in the screen.

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 43

Input channel operations

AD IN section

The AD IN section AD-converts the signals that are input from the rear panel INPUT jacks 1–48 and ST IN jacks 1–4, and

sends them to the input patch section. The structure of this section differs between the PM5D model and the PM5D-RH

model.

PM5D model

A [+48V ON/OFF] switch

If this switch is on, +48V is supplied to the condenser

mic or direct box connected to the INPUT jack 1–48.

B [PAD] switch

If this switch is on, the input level is attenuated by

26 dB.

C [GAIN] knob

Adjusts the input sensitivity of the input channel. The

range of adjustment is –34 dBu to +10 dBu (when the

PAD switch is on) or –60 dBu to –16 dBu (when the

PAD switch is off).

D [PEAK]/[SIGNAL] LED

The [SIGNAL] LED will light when the input level

reaches 14 dB below nominal level (i.e., 34 dB below

clipping level). The [PEAK] indicator will light when

the signal reaches 3 dB below clipping level.

E [INSERT ON/OFF] switch

This switch enables/disables the INSERT IN/OUT jack

located on the rear panel.

F ST IN [GAIN] knob

Adjusts the input sensitivity of the ST IN channel. The

range of adjustment is –34 dBu to +10 dBu.

G ST IN [PEAK]/ST IN [SIGNAL] LED

The ST IN [SIGNAL] LED will light when the input

level of the ST IN channel reaches 14 dB below nomi-

nal level (34 dB below clipping level). The ST IN

[PEAK] indicator will light when the signal reaches

3 dB below clipping level.

H [LAMP DIMMER] knob

This adjusts the brightness of the lamp connected to

the LAMP connector.

PM5D model

PM5D-RH model

DSP5D

Items in the AD IN section

5 Input channel operations

44 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

PM5D-RH model

A [+48V ON/OFF] LED

This LED will light if phantom power (+48V) is being

supplied to the corresponding INPUT jacks 1–48 or ST

IN jacks 1–4. However, +48V will not be supplied

unless the rear panel [+48V MASTER] switch is on.

B [PEAK]/[SIGNAL] LED

The [SIGNAL] LED will light when the input level

reaches 14 dB below nominal level (i.e., 34 dB below

clipping level). The [PEAK] indicator will light when

the signal reaches 3 dB below clipping level.

C [LAMP DIMMER] knob

This adjusts the brightness of the lamp connected to

the LAMP connector.

On the PM5D-RH model, the AD IN input signal sensitiv-

ity and phantom power (+48V) on/off setting for each

channel are controlled from within the display. However,

the rear panel [+48V MASTER] switch is the phantom

power master switch.

You can adjust the input sensitivity and switch phantom

power (+48V) on/off for the signals being input from

INPUT jacks 1–48 and ST IN jacks 1–4. These operations

are performed differently on the PM5D model and PM5D-

RH model.

Hint

Even if input channels are paired, head amp settings must be

made individually.

PM5D model

For the PM5D model, head amp settings are made using

the controls of the AD IN section of the panel (➥ p.43).

• The input sensitivity is adjusted by the combination of

the [GAIN] knob setting and [PAN] switch on/off set-

ting for that jack.

• To supply phantom power (+48V) to an INPUT jack

1–48, turn on the [+48V] switch corresponding to that

jack.

• To enable an external device that is inserted into the

INSERT IN/OUT jacks, turn on the [INSERT] switch

corresponding to that jack.

PM5D-RH model/DSP5D

On the PM5D-RH model/DSP5D, head amp settings are

made by operations within the display.

Repeatedly press the [SYS/W.CLOCK] key of

the DISPLAY ACCESS section until the HA

screen appears.

In the screen, click the INTERNAL HA button.

The internal head amp settings for INPUT jacks 1–48

and ST IN jacks 1–4 will be displayed.

Use the buttons and knobs in the screen to

edit the head amp settings.

A +48V button

Click this button to switch phantom power (+48V) on/

off for that jack.

B GAIN knob

Drag this knob to adjust the input sensitivity of that

jack in a range of +10 dB to –62 dB.

Note

The PAD will be switched on or off internally when the gain of

the PM5D-RH internal head amp is adjusted between –14 dB

and –13 dB. Keep in mind that noise may be generated if

there is a difference between the Hot and Cold output imped-

ance of the external device connected to the INPUT

connector/ST IN connector when using phantom power.

C GANG button

If this button is on, the input sensitivity of two adja-

cent odd-numbered/even-numbered channels will

change in tandem, maintaining the current offset value.

When making these settings, the LEDs of the AD IN

section of the panel will indicate the input signal level

and the phantom power (+48V) on/off status.

Note

• On the PM5D-RH model and DSP5D, head amp settings can

also be made from the HA/INSERT function CH 1-24 screen,

CH 25-48 screen, or ST IN/FX RTN screen (

➥

p.283).

• Settings for an external head amp device (AD8HR) can also

be made from the screen in the same way as for the inter-

nal head amps.

Controlling the input sensitivity and

phantom power (+48V) of the head amp

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 45

Input channel operations

INPUT channel strip

The INPUT channel strip is the section where you can control the principal parameters of the input channels.

This section is layered as shown in the following diagram; choose the CH 1-24 layer when you want to control input channels

1–24, or the CH 25-48 layer when you want to control input channels 25–48.

Note

If the console is cascade-connected to a DSP5D, you can use user-defined keys (

➥

p.148) or the FADER MODE key (

➥

p.149) to select a

DSP5D layer.

A [CH 1-24]/[CH 25-48] keys

These keys select the layer (CH 1-24 or CH 25-48) con-

trolled by the INPUT channel strip. The LED of the

currently selected layer will light.

B [PRE] key

This selects the output location of the signal when send

level to MIX bus 1–24 is selected as the encoder func-

tion. The pre-fader signal is sent to the corresponding

MIX bus if this key is on, and the post-fader signal is

sent if this key is off.

C ENCODER [ON] key

This switches the function currently assigned to the

encoder on/off. By default, this switches the signal sent

from the input channel to MIX buses 1–24 on/off.

D Encoder

According to the selection in the ENCODER MODE

section / FADER FLIP section (➥ p.48), this encoder

adjusts the send level from the input channel to MIX

buses 1–24, the panning of the input channel, or the

level of the input channel in the layer that is not cur-

rently selected. By default, this adjusts the send level to

MIX buses 1–24.

E [SEL] key

This selects the input channel that you will control

from the SELECTED CHANNEL section or from

within the display.

F Name indicator

This displays the name that has been assigned to the

input channel.

G CH [ON] key

Switches the input channel on/off. If this key is off

(LED dark), no signal will be sent from that input

channel to the STEREO bus or MIX buses.

H Fader

This 100 mm fader adjusts the input level of the input

channel.

CH 1-24 layer

CH 25-48 layer

Items in the INPUT channel strip

5 Input channel operations

46 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

I [CUE] key

This key lets you cue-monitor the signal of the input

channel.

J [TO ST] LED

This LED will light when the signal sent from the input

channel to the STEREO bus is on.

K [COMP] LED

This indicates the operational status of the compressor

for the input channel. This will be dark when the gain

reduction amount is 0 dB, dimly lit when it is 0–10 dB,

and lit when it is greater than 10 dB.

L [GATE] LED

This indicates the operational status of the gate for the

input channel. This will be dark when the gain reduc-

tion amount is 0 dB, dimly lit when it is 0–30 dB (or 0–

10 dB when ducking), and lit when greater than this.

M Meter LEDs

This is a six-point LED meter that indicates the input

level of the input channel. OVER indicates clipping

level, and –6 to –60 indicate the level of the signal rela-

tive to clipping level (0 dB). The level detection point

can be switched.

N DCA assign LEDs

The LED of the DCA group to which that input chan-

nel is assigned will light.

O MUTE assign LEDs

The LED of the mute group to which that input chan-

nel is assigned will light.

P [RCL SAFE]/[MUTE SAFE] LEDs

The corresponding LED will light when recall safe or

mute safe is enabled for the input channel.

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 47

Input channel operations

ST IN/FX RTN channel strip

In this section you can control the ST IN channels and FX RTN channels.

This section is layered as shown in the diagram below; choose the ST IN layer when you want to control the ST IN channels,

or the FX RTN layer when you want to control the FX RTN channels.

Note

If the console is cascade-connected to a DSP5D, you can use

user-defined keys (

➥

p.148) or the FADER MODE key

(

➥

p.149) to select a DSP5D layer.

A [ST IN 1-4]/[FX RTN 1-4] keys

These keys select the layer that will be controlled by the

ST IN/FX RTN channel strip. Press the [ST IN 1-4] key

to control ST IN channels 1–4, or press the [FX RTN 1-

4] key to control FX RTN channels 1–4.

Items

2–P below are the same as in the INPUT channel

strip (➥ p.45). However since FX RTN channels do not

have a gate or compressor, the [GATE] LED (

L) and

[COMP] LED (

K) are not used.

B [PRE] key

C ENCODER [ON] key

D Encoder

E [SEL] key

F Name indicator

G CH [ON] key

H Fader

I [CUE] key

J [TO ST] LED

K [COMP] LED

L [GATE] LED

M Meter LEDs

N DCA assign LEDs

O MUTE assign LEDs

P [RCL SAFE]/[MUTE SAFE] LEDs

FX RTN 1-4 layer

ST IN 1-4 layer

Items in the ST IN/FX RTN channel

strip

5 Input channel operations

48 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

FADER FLIP/ENCODER MODE section

In the FADER FLIP/ENCODER MODE section you can change the parameter that is assigned to the encoders, and exchange

the parameters assigned to the faders and encoders.

A FADER [FLIP] key

If this key is on, the parameters controlled by the fad-

ers and encoders will be exchanged.

B Encoder mode indicator

This indicates the number of the MIX bus (1–24)

selected by the MIX SEND SELECT keys (

6) or the

encoder function selected by keys

3–5.

C [PAN] key

This key selects pan (balance) as the parameter con-

trolled by the encoders. The encoder mode indicator

will indicate “Pn” while this key is on.

D [GAIN/ATT] key

This key selects input sensitivity to the internal head

amp (PM5D-RH model only) or external head amp

device (AD8HR or AD824) or attenuation immedi-

ately after AD conversion as the parameter controlled

by the encoders. The encoder mode indicator will indi-

cate “HA” (if input sensitivity to the head amp is

selected) or “At” (if attenuator is selected) while this

key is on.

Note

If you don’t want it to be possible to select the attenuators,

access the UTILITY function PREFERENCE 1 screen, and

turn ATT OPERATION ON PANEL off (

➥

p.206).

E [ALT LAYER] key

This key selects “input level of the channel not

included in the currently selected layer” as the parame-

ter controlled by the encoders. The encoder mode

indicator will indicate “AL” while this key is on.

F MIX SEND SELECT [1]–[24] keys

These keys select the MIX bus (1–24) whose send level

will be controlled by the encoders. When you press one

of these keys, the LED of that key will light, and the

encoder mode indicator will show the number of the

MIX bus.

Hint

If you turn on any key

–

, the remaining keys will automati-

cally turn off.

Items in the FADER FLIP/ENCODER

MODE section

5432

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 49

Input channel operations

Various operations for input channels

When the PM5D is in the default state, the encoders of the

INPUT channel strip and ST IN/FX RTN channel strip are

assigned to control send levels to MIX buses 1–24. How-

ever you can use the various ENCODER MODE keys to

select one of the following as the function of the encoders.

The currently selected function is shown by the key that is

lit and by the encoder mode indicator.

Repeatedly pressing the [PAN] key or [ALT LAYER] key

will alternate between the function selected by that key and

the MIX bus send level. Repeatedly pressing the [GAIN/

ATT] key will alternate between the following three

choices; input sensitivity to the internal head amp → atten-

uator → MIX bus send level.

Hint

If the FADER section [FLIP] key is on, the functions controlled

by the encoders and faders will be exchanged.

You can use the FADER [FLIP] key to exchange the func-

tions assigned to the faders and encoders of the channel

strip.

For example with the default setting (FADER [FLIP] key

off), the faders control the input channel input levels, and

the encoders control the send levels to the MIX buses. If

you then press the FADER [FLIP] key to make the LED

light, the faders will control the send levels to the MIX

buses and the encoders will control the input channel

input levels.

The function assigned to the controls when the [FLIP] key is on (LED lit) will depend on the current encoder mode as follows.

Note

The DCA channel strip and STEREO A/B channel strip are not affected by the on/off status of the [FLIP] key.

Key Encoder function Display

MIX SEND SELECT

[1]–[24] keys

Send levels to MIX buses 1–24 1–24

[PAN] key Pan (balance) Pn

[GAIN/ATT] key Head amp input sensitivity HA

[GAIN/ATT] key Attenuator At

[ALT LAYER] key

Input level for the currently un-

selected layer

*1. In the INPUT channel strip, the CH 1-24 layer and the CH

25-48 layer are in a “front/rear” relation. In the ST IN/FX

RTN channel strip, the ST IN 1-4 layer and the FX RTN 1-4

layer are in a “front/rear” relation.

Selecting the function of the encoders

Exchanging the fader and encoder

functions

➠

Control the channel input

level and on/off status

Control the channel input

level and on/off status

Control the send level and on/off

status of the signal sent from the

channel to the MIX buses

Control the send level and on/off

status of the signal sent from the

channel to the MIX buses

[FLIP]

key

Encoder

mode

Function of each control

Encoder ENCODER [ON] key Fader CH [ON] key

Off

MIX

SEND

Send level from channel to

MIX bus

On/off status of signal sent

from channel to MIX bus

Channel (currently

selected layer) input level

Channel (currently

selected layer) on/off

PA NPan (balance)

On/off status of signal sent

from channel to STEREO

bus

GAIN/ATT

Head amp input sensitivity

/ attenuator

No function

ALT

LAYER

Channel (currently un-

selected layer) input level

Channel (currently un-

selected layer) on/off

MIX

SEND

Channel (currently

selected layer) input level

Channel (currently

selected layer) on/off

Send level from channel

(currently selected layer) to

MIX bus

On/off status of signal sent

from channel (currently

selected layer) to MIX bus

PA N

Pan of the signal sent from

channels (of the currently

selected layer) to paired

MIX buses (invalid if MIX

channels are not paired)

Channel (currently

selected layer) on/off

GAIN/ATT

Head amp input sensitivity

/ attenuator

No function

ALT

LAYER

Send level from channel

(currently un-selected

layer) to MIX bus

On/off status of signal sent

from channel (currently un-

selected layer) to MIX bus

5 Input channel operations

50 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Here’s how to use the INPUT channel strip or ST IN/FX

RTN channel strip to send an input channel signal to the

STEREO bus. The explanation here uses the example of an

input channel, but the procedure is essentially identical

when using a ST IN channel or FX RTN channel.

Make sure that an input source is correctly

assigned to the input channel, and that the

head amp gain is set appropriately.

Make sure that the appropriate CH [ON] key is

turned on in the INPUT channel strip, and

press the [SEL] key for that channel to make it

light.

The [SEL] keys are used to select the channel you want

to control.

In the SELECTED CHANNEL section, press the

[TO STEREO] key to make it light.

In the SELECTED CHANNEL section you can make

detailed parameters settings for the channel currently

selected by its [SEL] key. (For details on the

SELECTED CHANNEL section ➥ p.65.)

When you turn on the [TO STEREO] key, the signal

sent from that input channel to the STEREO bus will

be turned on. At this time, the [TO ST] LED of the

INPUT channel strip will light.

Raise the corresponding fader of the INPUT

channel strip.

The level of the input signal is shown by the level meter

located at the right of the CH [ON] key.

Turn on the [PAN] key in the ENCODER MODE

section.

Use the encoder in the INPUT channel strip to

adjust the pan of the input channel.

Note

If you are sending the signal from a ST IN channel / FX RTN

channel to the STEREO bus, you can repeatedly press the

[SEL] key to switch between L/R channels, and make pan set-

tings for each channel.

In the STEREO A/B channel strip, turn the STE-

REO A [ON] key and STEREO B [ON] key on

(LED lit).

In the STEREO A/B channel strip, raise the

[STEREO A]/[STEREO B] faders.

The signal sent to the stereo bus will be routed through

the STEREO A/B channels and output from the STE-

REO OUT A/B jacks.

Sending a signal from an input chan-

nel to the STEREO bus

CH [ON] key

[SEL] key

Level meter

STEREO [PAN] encoder

[TO STEREO] key

STEREO B

[ON] key

STEREO A

[ON] key

STEREO A

fader

STEREO B

fader

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 51

Input channel operations

Signals from input channels or ST IN/FX RTN channels

can be sent to the desired MIX bus. This can be done either

by specifying the send level sent from all input channels to

a specific MIX bus, or by specifying the send level sent

from a specific input channel to all MIX buses.

The explanation here uses an input channel as the send-

source, but the procedure is the same when using a ST IN

channel or FX RTN channel.

To send signals from all input channels to

a speciﬁc MIX bus

Use MIX SEND SELECT [1]–[24] keys of the

ENCODER MODE section to select the destina-

tion MIX bus.

The selected key will light, and the encoder mode indi-

cator will show the number of the destination MIX

bus. In this state, the encoders of the channel strip

adjust the send level to the MIX bus. Make sure that

the FADER [FLIP] key is dark.

Turn the encoders of the INPUT channel strip.

When MIX SEND is selected as the encoder mode, you

can use the encoders of the INPUT channel strip to

adjust the level of the signal that is sent to the currently

selected MIX bus from the corresponding input

channel.

The LEDs around the periphery of the encoder indi-

cate the approximate send level.

To turn off the signal sent from a specific

channel to the MIX bus, press the ENCODER

[ON] key for that channel to turn it off.

Press the same key once again to turn it back on.

Note

If the send-destination MIX bus is set to FIXED mode

(

➥

p.299), the encoders have no effect; the signal can only be

switched on/off by the ENCODER [ON] key.

In the same way, select a different send-desti-

nation MIX bus, and use the encoders of the

INPUT channel strip to adjust the send levels

to it.

To send signals from a speciﬁc input chan-

nel to all MIX buses

Press a [SEL] key of the INPUT channel strip to

select the send-source channel.

In the MIX section, press the [MIX SEND] key

to make it light.

The MIX section lets you control the signals sent to

MIX buses 1–24 and the signals output from MIX

channels 1–24. (For details, refer to ➥ p.57)

When the [MIX SEND] key is lit, you can use the

encoders of the MIX section to control the send levels

from the currently selected input channel to MIX buses

1–24.

Hint

When the [MIX MASTER] key of the MIX section is lit, you can

hold down the [SEL] key of an input channel to make the [MIX

SEND] key light (the [MIX MASTER] key will go dark). In this

state, you can use the encoders of the MIX section to adjust

the send levels from the selected channel to MIX buses 1–24.

Turn the MIX encoders to adjust the send lev-

els to the MIX buses.

The LEDs around the periphery of the encoder indi-

cate the approximate send level.

Sending the signal from the input

channel to a MIX bus

Switches the sig-

nal sent from the

input channel to

the MIX bus on/

off.

Adjusts the send

level of the signal

sent from the

input channel to

the MIX bus.

MIX bus

Input channels

[MIX SEND] key [MIX MASTER] key

MIX [ON] key

MIX encoder

5 Input channel operations

52 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

To turn off the signal sent from that channel

to a MIX bus, press the MIX [ON] key to turn it

off.

Press the MIX [ON] key once again to turn it back on.

Note

MIX buses can be switched (in units of two adjacent odd-num-

bered/even-numbered MIX buses) between VARI type (send

levels are variable) and FIXED type (send levels are fixed).

(For details on switching the type

➥

p.299)

If the send-destination MIX bus is set to FIXED mode, the MIX

encoders have no effect; the signal can only be switched on/

off by the MIX [ON] key.

MIX bus

Input channels

Switches the sig-

nal sent from the

input channel to

the MIX bus on/

off.

Adjusts the send

level of the signal

sent from the

input channel to

the MIX bus.

MIX1

MIX2

STEREO L

STEREO R

……

FADER

INPUT CHANNEL 1

PAN

MIX1 (VARI)

LEVEL

MIX2 (VARI)

LEVEL

FADER

INPUT CHANNEL 2

PAN

MIX1 (VARI)

LEVEL

MIX2 (VARI)

LEVEL

❏ When sending a signal from an input channel to

a VARI type MIX bus

MIX1

MIX2

STEREO L

STEREO R

……

FADER

INPUT CHANNEL 1

PAN

MIX1 (FIX)

MIX2 (FIX)

FADER

INPUT CHANNEL 2

PAN

MIX1 (FIX)

MIX2 (FIX)

❏ When sending a signal from an input channel to

a FIXED type MIX bus

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 53

Input channel operations

Monaural input channels can be paired to link their princi-

pal parameters. There are two types of pairing; you can use

only one type.

• Horizontal pair mode

This mode pairs adjacent odd-numbered/even-num-

bered channels (default setting).

• Vertical pair mode

This mode pairs channels of different layers that share

the same fader.

Hint

Input channels that are paired will have their parameters

linked except for head amp, delay, pan, attenuation, and

phase.

Note

If the PM5D is cascade-connected to the DSP5D, pairing can

be specified only within each individual machine.

❏ Using horizontal pairing

Here’s how to enable or defeat pairing for adjacent odd-

numbered/even-numbered channels.

To enable pairing, hold down the [SEL] key of

one of the adjacent odd-numbered/even-num-

bered channels, and press the [SEL] key of the

other channel.

The parameters of the channel you pressed first will be

copied to the subsequently-pressed channel.

Hint

The copy-source channel is determined by the order in which

you press the [SEL] keys. For example if you hold down the

channel 1 [SEL] key and press the channel 2 [SEL] key, the

channel 1 parameters will be copied to channel 2.

To defeat pairing, hold down the [SEL] key of

one of the paired channels and press the [SEL]

key of the other channel.

Note

If you are unable to enable/defeat pairing by using the above

procedure, make sure that MAKE PAIR ON PANEL is turned

on in the UTILITY function PREFERENCE 1 screen

(

➥

p.206).

❏ Using vertical pairing

Here’s how to enable or disable pairing for channels of dif-

ferent layers that share the same fader.

Repeatedly press the [SYS/W.CLOCK] key of

the DISPLAY ACCESS section until the MIXER

SETUP screen appears.

Click the VERTICAL PAIR button in the PAIR

MODE area to turn it on.

A window will appear, asking you to confirm that you

want to change the pair mode.

Click the OK button.

Now you can use “vertical pair” mode.

When you switch to “vertical pair” mode, new num-

bers will be assigned to the input channels. For details,

refer to p.221.

You can return to “horizontal pair mode” by clicking

the HORIZONTAL PAIR button to turn it on.

Enabling/disabling pairing

Horizontal pair

Vertical pair

PAIR MODE area

VERTICAL PAIR button

MIXER SETUP

5 Input channel operations

54 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Hint

When you switch between vertical pair mode and horizontal

pair mode, the input channel numbers will change, but the

channel names and parameter values will not change.

Hold down the [SHIFT] key of the data entry

section, and press the [SEL] key of one of the

channels you want to pair.

A window will appear, allowing you to select how pair-

ing will be handled.

Click the appropriate button to choose the

source/destination for the parameters that will

be copied.

The channels will be paired as you specify.

Hint

If you click the RESET BOTH button, the parameters of both

channels will be reset to their default value.

To defeat pairing, hold down the [SHIFT] key

and press the [SEL] key of one of the channels.

A window will ask you to confirm that you want to

defeat pairing. Click the OK button to defeat pairing.

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 55

Output channel operations

This chapter explains the functions and operation of each section related to output channels.

About the output channels

Output channels mix the signals sent from input channels etc., and send them to the corresponding output jacks or output

buses.

There are three types of output channel, as follows.

Note

The DSP5D does not have MIX OUT jacks, MATRIX OUT jacks, or STEREO OUT jacks. Output channels are assigned to OMNI OUT

jacks for use.

MIX channels 1–24

Signals sent from input channels to MIX buses are sent via these channels to the MIX OUT jacks 1–24 or the STEREO/

MATRIX buses. If the output patching is in its default state, the PM5D assigns MIX channels 1–24 to MIX OUT jacks 1–24,

and the DSP5D assigns MIX channels 1–22 to OMNI OUT jacks 1–22.

STEREO A/B channels

The signals sent from input channels or MIX channels are sent via these channels to STEREO OUT jacks A/B.

If the DSP5D’s output patching is in its default state, the STEREO A channel is assigned to OMNI OUT jacks 23–24.

6 Output channel operations

56 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

MATRIX channels 1–8

The signals sent from MIX channels or STEREO A/B channels to MATRIX buses are sent via these channels to the MATRIX

OUT jacks.

•8 BAND EQ (8 band equalizer) (MIX channels and

STEREO A/B channels)

This is an eight-band (four upper bands + four lower

bands) parametric EQ.

•4 BAND EQ (4 band equalizer) (MATRIX channels)

This is a four-band (HIGH, HIGH MID, LOW MID,

LOW) parametric EQ.

• COMP (Compressor)

This is a dynamics processor that can be used as a com-

pressor, expander, or limiter.

• LEVEL

This adjusts the output level of the channel.

• ON (On/off)

This switches the channel on/off. If this is off, that

channel will be muted.

• OUTPUT DELAY

This delays the output signal. It can be used to make

fine adjustments in the relative timing between

channels.

• OUT ATT. (Output attenuator)

This attenuates or boosts the level of the channel’s out-

put signal.

• METER

This meter indicates the output level of the output

channel. The level detection point can be switched.

• MIX to STEREO (MIX channels)

This is an on/off switch for the signal sent from the

MIX channel to the STEREO bus.

• to MATRIX (MIX channels and STEREO A/B

channels)

This is an on/off switch for the signal sent from the

MIX channel to the MATRIX bus.

• PAN (MIX channels)

This adjusts the panning of the signal sent from the

MIX channel to the STEREO bus.

• BAL (Balance) (STEREO channels)

This adjusts the L/R volume balance of the STEREO

channel.

• LCR (Left/Center/Right) (MIX channels)

This sends the three-channel signal (left/right channels

and a center channel) to the STEREO bus.

• INSERT

Here you can patch the desired output port and input

port to insert-out/insert-in, allowing an external effect

processor or other device to be inserted. You can

switch the insert-out and insert-in locations.

• OUTPUT PATCH

Here, output channels can be assigned to output jacks.

Hint

STEREO A/B channels, and MATRIX channels 1–8 are

always connected to STEREO OUT jacks A/B, and MATRIX

OUT jacks 1–8 respectively. However, you can also make out-

put patch settings to send the signals of these output channels

and MIX channels 1–24 to slots 1–4, the 2TR OUT DIGITAL

jacks or the MIX OUT jacks.

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 57

Output channel operations

MIX section

The MIX section adjusts the send level of the signals sent from input channels to MIX buses, and adjusts the output level of

the MIX channels.

A [TO ST] LED

This LED will light when the signal sent from the MIX

channel to the STEREO bus is on.

B [TO MTRX] LED

This LED will light when the signal sent from the MIX

channel to the MATRIX bus is on.

C DCA group LEDs

The LED of the DCA group to which this MIX channel

is assigned will light.

D MIX [PAIR] LED

This LED will light if adjacent odd-numbered/even-

numbered MIX channels are paired.

E MIX [ON] key

If the [MIX SEND] key (9) is on, this switches the sig-

nal sent from the input channel to the MIX bus on/off.

If the [MIX MASTER] key (

J) is on, this switches the

MIX channel on/off.

F MIX encoder

If the [MIX SEND] key (9) is on, this adjusts the send

level to the MIX bus. If the [MIX MASTER] key (

J) is

on, this adjusts the output level of the MIX channel.

G MIX [CUE] key

This is used to monitor a MIX channel via the Cue

Monitor/Solo function.

H MIX [SEL] key

This selects the MIX channel to which operations in

the SELECTED CHANNEL section or in the display

will apply.

I [MIX SEND] key

J [MIX MASTER] key

These keys switch the operation of the MIX section.

When the [MIX SEND] key is on, you can use the con-

trols of the MIX section to edit the send level and on/

off status of the signal being sent from the currently

selected input channel to the MIX buses. Controls

other than

4–6 will have no effect.

When the [MIX MASTER] key is on, you can use the

controls of the MIX section to edit the output level and

on/off status of the MIX channels.

❏ Sending signals from MIX channels to

output jacks

Here’s how a signal sent from an input channel to a MIX

bus can be sent from the corresponding MIX OUT jack.

Make sure that an appropriate signal is being

sent from an input channel to the MIX bus.

Press the [MIX MASTER] key in the MIX

section.

When this key is on, you can use the MIX section to

control the signals being sent from the MIX channels

to the MIX OUT jacks.

Turn on the MIX [ON] key for the MIX chan-

nel whose signal you want to output.

Turn the MIX encoder to adjust the output

level of the corresponding MIX channel.

The signal of the corresponding MIX channel will be

sent from the corresponding MIX OUT jack.

If you want the meters of the panel to indi-

cate the output level of the MIX channels,

press the [MIX/MATRIX] key of the meter

section.

The output level of the MIX channels will be shown by

the [INPUT/MIX] meters.

Items in the MIX section

124

Operations in the MIX section

MIX

PEAK

HOLD

CH 1 -24

OVER

-3

-6

-9

-12

-15

-18

-24

-30

-40

-50

-60

OVER

-3

-6

-9

-12

-15

-18

-24

-30

-40

-50

-60

2322212019181716151413121110987654321

ST IN/

/ST IN

MATRIX

INPUT/MIX meters

[MIX/MATRIX] key

6 Output channel operations

58 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Hint

The detection point (metering point) of the signal levels shown

in the meters can be changed if desired. For details, refer to

p.109.

❏ Sending signals from MIX channels to

MATRIX buses

Here’s how a signal sent from an input channel to a MIX

bus can be output to a MATRIX bus. This can be done

either by specifying the send level sent from all MIX chan-

nels to a specific MATRIX bus, or by specifying the send

level sent from a specific MIX channel to all MATRIX

buses.

To send signals from all MIX channels to a

speciﬁc MATRIX bus

Make sure that appropriate signals are being

sent from input channels to the MIX buses.

Repeatedly press the [MATRIX/ST] key of the

DISPLAY ACCESS section to access the

MATRIX/ST ROUTING screen shown below.

Use the left/right scroll bar to display the MIX

channel that you want to send to the MATRIX

bus, and click the MIX TO MATRIX ON/OFF

button to turn it on.

The signal of the corresponding MIX channel is now

sent to the MATRIX bus.

Hint

You can use the PRE FADER/POST FADER buttons in the

MIX TO MATRIX area to change the send point (pre-fader/

post-fader) of the signal sent from the MIX channel to the

MATRIX bus.

Press the [MIX MASTER] key in the MIX

section.

Press and hold the MATRIX [SEL] key for the

send-destination MATRIX bus.

All MIX [SEL] keys will blink. As long as you hold

down the MATRIX [SEL] key, the MIX encoders 1–24

will respectively adjust the send levels from the MIX

channels to the currently selected MATRIX bus.

Continuing to hold down the MATRIX [SEL]

key, turn MIX encoders 1–24 to adjust the level

of the signal sent from each MIX channel to

the currently selected MATRIX bus.

The LEDs around the periphery of the MIX encoder

indicate the approximate level. When you take your

hand off the MATRIX [SEL] key, the encoders will

revert to their previous function.

Hint

You can fix the encoders in the above state by rapidly press-

ing the MATRIX [SEL] key twice. To return to the previous

state, press any MIX [SEL] key or MATRIX [SEL] key.

To send from a speciﬁc MIX channel to all

MATRIX buses

Make settings so that a signal is sent from the

desired MIX channel to a MATRIX bus, as

described in steps 1–3 of “To send signals from

all MIX channels to a specific MATRIX bus.”

Press the [MIX MASTER] key in the MIX

section.

Press and hold the MIX [SEL] key for the send-

source MIX channel.

All MATRIX [SEL] keys will blink. As long as you con-

tinue to hold down the MIX [SEL] key, MATRIX

encoders 1–8 will adjust the send levels sent from the

selected MIX channel to each MATRIX bus.

Continuing to hold down the MIX [SEL] key,

turn MATRIX encoders 1–8 to adjust the level

of the signal sent from the currently selected

MIX channel to the MATRIX buses.

The LEDs around the periphery of the MATRIX

encoder indicate the approximate send level. When

you take your hand off the MIX [SEL] key, the encod-

ers will revert to their previous function.

MIX channelsMIX TO MATRIX

ON/OFF buttons

MATRIX/ST ROUTING

Use the encoders of the MIX section to

adjust the send levels

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 59

Output channel operations

Hint

You can fix the encoders in the above state by rapidly press-

ing the MIX [SEL] key twice. To return to the previous state,

press any MIX [SEL] key or MATRIX [SEL] key.

If you want the meters of the panel to indi-

cate the output level of the MIX channels,

press the [MIX/MATRIX] key of the meter

section.

Hint

The send levels from MIX channels to MATRIX buses can

also be edited in the display. For details, refer to p.262.

❏ Sending signals from MIX channels to

the STEREO bus

Here’s how signals sent from input channels to MIX buses

can be output to the STEREO bus.

Make sure that appropriate signals are being

sent from input channels to the MIX buses.

Press the [MIX MASTER] key in the MIX

section.

Turn on the MIX [ON] key for the MIX chan-

nels whose signals you want to send to the

STEREO bus.

Press the MIX [SEL] key of the channel whose

signal you want to send to the STEREO bus,

and turn on the [TO STEREO] key of the

SELECTED CHANNEL section.

To adjust the pan of the signal sent from the

MIX channel to the STEREO bus, press the MIX

[SEL] key of the desired MIX channel and turn

the STEREO [PAN] encoder of the SELECTED

CHANNEL section.

Turn the MIX encoder to adjust the signal level

that is sent to the STEREO bus.

Hint

You can also switch the output to the STEREO bus on/off and

adjust the pan from within the MATRIX/ST ROUTING screen

(MATRIX/ST function). If desired, the send position (post fader

or post ON key) for the signal sent from the MIX channel to

the STEREO bus can also be changed in this screen

(

➥

p.264).

In the STEREO A/B channel strip, turn the STE-

REO A [ON] key and STEREO B [ON] key on

(LED lit).

In the STEREO A/B channel strip, raise the

[STEREO A]/[STEREO B] faders.

The signal sent from the MIX channel to the STEREO

bus will be sent from STEREO OUT jacks A/B.

The level of the signal output from the STEREO A/B

channels is shown by the [MASTER] meters in the

meter section.

❏ Pairing MIX channels

Adjacent odd-numbered/even-numbered MIX channels

can be paired. If two MIX channels are paired, their

parameters (with the exception of pan and delay) will be

linked.

Turn on the [MIX MASTER] key in the MIX

section.

Of the desired two adjacent odd-numbered/

even-numbered MIX channels, hold down the

MIX [SEL] key of one, and press the MIX [SEL]

key of the other.

The [PAIR] LED will light, and the MIX channels will

be paired. At this time, the parameters of the channel

whose MIX [SEL] key you pressed first will be copied

to the channel whose MIX [SEL] key you pressed later.

For example if you pressed the keys in the order of

MIX channel 1 → MIX channel 2, the parameters of

MIX channel 1 will be copied to MIX channel 2.

To defeat pairing, hold down the MIX [SEL]

key of one of the paired MIX channels and

press the MIX [SEL] key of the other channel.

When MIX channels are paired, the signal flow will

change as follows.

Use the encoders of the MATRIX section to

adjust the send level

STEREO [PAN] encoder

[TO STEREO] key

6 Output channel operations

60 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Signals sent from an input channel to a

VARI type MIX bus

• If the VARI type MIX bus is not paired

When the [MIX SEND] key is on, the MIX encoders

will adjust the send level of the signals sent to the corre-

sponding MIX bus from the currently selected input

channel.

• If the VARI type MIX bus is paired

When the [MIX SEND] key is on, MIX encoders of

odd-numbered channels will adjust the pan of the sig-

nal sent to the two MIX buses. MIX encoders of even-

numbered channels will adjust the shared send level for

the two MIX buses.

MIX channel output signals

• If MIX channels are not paired

When the [MIX MASTER] key is on, the MIX encod-

ers will adjust the output level of the corresponding

MIX channels.

• If MIX channels are paired

When the [MIX MASTER] key is on, the MIX encod-

ers of odd-numbered channels will adjust the volume

balance between paired MIX channels. The MIX

encoders of even-numbered channels will adjust the

shared level of the two paired channels.

Hint

MIX channel pairing status and output level/balance settings

can also be edited in the CH to MIX screen (

➥

p.299) or

MATRIX/ST screen (

➥

p.262).

MIX bus 1

SEND LEVEL

MIX bus 2

SEND LEVEL

MIX1

MIX2

STEREO L

STEREO R

……

FADER

INPUT CHANNEL

PAN

MIX1 (VARI)

LEVEL

MIX2 (VARI)

LEVEL

MIX bus 1/2

SEND PAN

MIX bus 1/2

SEND LEVEL

MIX1

MIX2

STEREO L

STEREO R

……

FADER

INPUT CHANNEL

PAN

MIX1/2 (VARI)

LEVEL

MIX channel 1

OUTPUT

LEVEL

MIX channel 2

OUTPUT

LEVEL

OUTPUT LEVEL

MIX OUT 1

MIX 1

MIX CHANNEL

OUTPUT LEVEL

MIX OUT 2

MIX 2

MIX channel

1/2 BALANCE

MIX channel

1/2 OUTPUT

LEVEL

OUTPUT LEVEL

MIX OUT 1BALANCE

MIX 1

MIX CHANNEL

MIX OUT 2

MIX 2

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 61

Output channel operations

STEREO A/B channel strip

The STEREO A/B channel strip lets you send the signal of the STEREO A/B channels to the MATRIX bus, and adjust the out-

put level of the STEREO A/B channels.

A [TO MATRIX] LED

This LED will light when the signal sent from the STE-

REO channel to the MATRIX bus is on.

B [COMP] LED

This indicates the operating status of the compressor

for the STEREO channel. This will be dark when the

gain reduction amount is 0 dB, dimly lit when it is 0–

10 dB, and lit when it is greater than 10 dB.

C STEREO A/B [SEL] key

This selects the STEREO A or STEREO B L/R channels

for editing in the SELECTED CHANNEL section or

display. The L/R channels will alternate each time you

press the key.

D STEREO [MONO] key

This switches the STEREO B channel to monaural. The

status will alternate between monaural and stereo each

time you press the key.

E STEREO [ON] key

This switches the STEREO channel on/off. If this key is

off (LED dark), no signal will be output from that STE-

REO channel.

F STEREO fader

This 100 mm fader adjusts the output level of the STE-

REO channel.

G STEREO [CUE] key

This is used to monitor the STEREO A/B channel via

the Cue Monitor/Solo function.

Items in the STEREO A/B channel

strip

6 Output channel operations

62 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

❏ Sending signals from the STEREO A/B

channels to output jacks

Here’s how the signals sent from input channels or MIX

channels to the STEREO bus can be output from STEREO

OUT jacks A/B.

Make sure that appropriate signals are being

sent from the desired channels to the STEREO

bus.

Turn on the STEREO [ON] key of the STEREO

A/B channel strip.

Raise the [STEREO A]/[STEREO B] faders.

The signal of the STEREO A/B channels will be output

from STEREO OUT jacks A/B. The output level of the

STEREO A/B channels is shown by the [MASTER]

meters in the meter section.

Hint

Normally, the same signal is output from the STEREO A and

B channels. However you can also use the STEREO B chan-

nel as a Center channel for L/C/R three-channel playback

(

➥

p.222, 267).

❏ Sending signals from the STEREO A/B

channels to MATRIX buses

Here’s how the signal of the STEREO A/B channels can be

sent to the MATRIX buses.

Make sure that an appropriate signal is being

input to the STEREO bus.

Repeatedly press the [MATRIX/ST] key of the

DISPLAY ACCESS section to access the

MATRIX/ST ROUTING screen.

Use the left/right scroll bar to display the STE-

REO A/B channels, and click the MIX TO

MATRIX ON/OFF button to turn it on.

With these settings, the signal of the STEREO A/B

channels will be sent to the MATRIX channels.

Make sure that the STEREO A/B [ON] keys are

turned on in the STEREO A/B channel strip;

then hold down the STEREO A [SEL] key or

STEREO B [SEL] key.

While you continue holding down the key, all

MATRIX [SEL] keys will blink. In this condition, you

can use the MATRIX encoders to adjust the signal lev-

els sent from the STEREO A or B channel to the

MATRIX buses.

While continuing to hold down the STEREO A

[SEL] key or STEREO B [SEL] key, turn MATRIX

encoders 1–8 to adjust the signal level sent to

the MATRIX buses.

The LEDs around the periphery of the MATRIX

encoder indicate the approximate send level. When

you take your hand off the STEREO A [SEL] key or

STEREO B [SEL] key, the MATRIX encoders will

revert to their previous function.

Hint

• You can also switch to the above state by rapidly pressing

the STEREO A [SEL] key or STEREO B [SEL] key twice. To

return to the previous state, press any [SEL] key.

• Send levels from the STEREO A/B channels to the MATRIX

buses can also be adjusted from within the display

(

➥

p.262).

Operations in the STEREO A/B chan-

nel strip

MASTER meters

MIX TO MATRIX

ON/OFF buttons

MATRIX/ST ROUTING

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 63

Output channel operations

MATRIX section

In the MATRIX section you can adjust the send levels from MIX channels to MATRIX buses, and adjust the output level of

the MATRIX channels.

A DCA group LEDs

The LED of the DCA group to which this MATRIX

channel is assigned will light.

B MATRIX [PAIR] LED

This LED will light if adjacent odd-numbered/even-

numbered MATRIX channels are paired.

C MATRIX [ON] key

This switches the MATRIX channel on/off.

D MATRIX encoder

This adjusts the output level of the MATRIX channel.

E MATRIX [CUE] key

This is used to monitor a MATRIX channel via the Cue

Monitor/Solo function.

F MATRIX [SEL] key

This selects the MATRIX channel to which operations

in the SELECTED CHANNEL section or in the display

will apply.

❏ Sending signals from the MATRIX sec-

tion to output jacks

Here’s how the signals sent from MIX channels or STE-

REO A/B channels to MATRIX buses can be sent to the

MATRIX OUT jacks.

Make sure that appropriate signals are being

sent from the MIX channels or STEREO A/B

channels to the MATRIX buses.

In the MATRIX section, press the MATRIX [ON]

buttons to turn the desired MATRIX chan-

nel(s) on.

Turn the encoders of the MATRIX section to

adjust the output level of the MATRIX

channels.

The signals sent to the MATRIX bus(es) will be sent

from the corresponding MATRIX OUT jack(s).

To check the output level of the MATRIX chan-

nels, press the [MIX/MATRIX] key in the meter

section.

The [ST IN/MATRIX] meters will show the output

levels.

Hint

The detection point (metering point) of the signal levels shown

in the meters can be changed if desired (

➥

p.109).

❏ Pairing the MATRIX section

Adjacent odd-numbered/even-numbered MATRIX chan-

nels can be paired if desired. If two channels are paired,

their parameters (with the exception of pan and delay) will

be linked.

In the MATRIX section, hold down the MATRIX

[SEL] key for one of two adjacent odd-num-

bered/even-numbered channels, and press the

MATRIX [SEL] key of the other channel.

The [PAIR] LED will light, and the MATRIX channels

will be paired. At this time, the parameters of the chan-

nel whose MATRIX [SEL] key you pressed first will be

copied to the channel whose MATRIX [SEL] key you

pressed later.

For example if you pressed the keys in the order of

MATRIX channel 1 → MATRIX channel 2, the param-

eters of MATRIX channel 1 will be copied to MATRIX

channel 2.

To defeat pairing, hold down the [SEL] key of

one of the paired MATRIX channels and press

the [SEL] key of the other MATRIX channel.

When MATRIX channels are paired, the signal flow

will change as follows.

Items in the MATRIX section

Operations in the MATRIX section

OVER

-3

-6

-9

-12

-15

-18

-24

-30

-40

-50

-60

OVER

-3

-6

-9

-12

-15

-18

-24

-30

-40

-50

-60

1L 1R 2L 2R 3L 3R 4L 4R

MATRIX

ST IN / /

1 2 3 4 5 6 7 8

MIX

PEAK

HOLD

CH 1-24

ST IN/

/ST IN

MATRIX

ST/IN MATRIX meters

[MIX/MATRIX] key

6 Output channel operations

64 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Signals sent from MIX channels and STE-

REO A/B channels to MATRIX buses

• If MATRIX channels are not paired

When you are holding down the [SEL] key of a spe-

cific MIX channel or STEREO A/B channel in order to

adjust the send levels from that channel to all MATRIX

buses, the MATRIX encoders will adjust the send level

to the corresponding MATRIX bus.

• If MATRIX channels are paired

When you are holding down the [SEL] key of a spe-

cific MIX channel or STEREO A/B channel in order to

adjust the send levels from that channel to all MATRIX

buses, the MATRIX encoder of the odd-numbered

channel will adjust the pan of the signal sent to the two

MATRIX buses. The MATRIX encoder of the even-

numbered channel will adjust the send level shared by

the two MATRIX buses.

Hint

For details on how to send the signal of a specific MIX chan-

nel to all MATRIX buses, refer to p.58. For details on how to

send the signal from either the STEREO A or B channel to all

MATRIX buses, refer to p.62.

Output signals from MATRIX channels

• If MATRIX channels are not paired

The MATRIX encoders adjust the output level of the

corresponding MATRIX channel.

• If MATRIX channels are paired

MIX encoders of odd-numbered channels adjust the

volume balance between paired MATRIX channels.

MATRIX encoders of even-numbered channels will

adjust the shared level of the two paired channels.

Hint

You can access the MATRIX/ST ROUTING screen (MATRIX/

ST function) to see a list of the MATRIX channels in the dis-

play, and edit the pairing and other parameters. For details,

refer to p.262 of the Reference section.

……

MATRIX1

MATRIX2

FADER

MIX CHANNEL

MATRIX1

LEVEL

MATRIX2

LEVEL

MATRIX 1

LEVEL

encoder

MATRIX 2

LEVEL

encoder

PAN

to MATRIX 1/2

LEVEL

……

MATRIX1

MATRIX2

FADER

MIX CHANNEL

MATRIX 1/2

PA N encoder

MATRIX1/2

LEVEL

encoder

MATRIX chan-

nel 1 OUTPUT

LEVEL

encoder

MATRIX chan-

nel 2 OUTPUT

LEVEL

encoder

OUTPUT LEVEL

OUTPUT PATCH

MATRIX 1

MATRIX CHANNEL

OUTPUT LEVEL

MATRIX 2

MATRIX

channel 1/2

BALANCE

encoder

MATRIX

channel 1/2

OUTPUT

LEVEL

encoder

OUTPUT PATCH

MATRIX 1

MATRIX CHANNEL

MATRIX 2

OUTPUT LEVEL

BALANCE ON

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 65

Using the Selected Channel section

This chapter explains how you can use the SELECTED CHANNEL section to control input chan-

nels and output channels.

About the SELECTED CHANNEL section

The SELECTED CHANNEL section lets you edit the mix parameters of the currently selected input channel or output chan-

nel; it corresponds to a channel module of a conventional analog mixer.

This section controls the channel that was last selected by pressing its [SEL] key. (In the case of an ST IN channel, FX TRN

channel, or STEREO A/B channel, you will select either the L or the R channel.) However, you will be able to edit essentially all

of the mix parameters (head amp settings, EQ/compressor/gate settings, output to the STEREO bus, DCA group and mute

group assignments, etc.) using panel controls.

Items in the SELECTED CHANNEL section

Here you can assign the currently selected channel to DCA

groups and mute groups. (For details on DCA groups and

mute groups ➥ p.82, 83)

A DCA [1]–[8] keys

These keys assign the selected channel to DCA groups

1–8. The key LED for the assigned DCA group(s) will

light.

Input channels can use DCA groups 1–8, and output

channels can use DCA groups 7/8. For DCA groups 7/

8, input channels and output channels can both exist in

the same-numbered group.

B MUTE [1]–[8] keys

These keys assign the selected channel to mute groups

1–8. The key LED for the assigned mute group(s) will

light.

Mute groups 1–8 allow you to mix input channels and

output channels.

C [RECALL SAFE] key

This key switches Recall Safe on/off for the selected

channel. If this key is on, the parameters of the corre-

sponding channel will not be affected when a scene is

recalled. The applicable parameters can be specified in

the RECALL SAFE screen (SCENE function)

(➥ p.182).

D [MUTE SAFE] key

This key switches Mute Safe on/off for the selected

channel. If this key is on, the corresponding channel

will be temporarily excluded from mute groups.

E Level meter

This indicates the input/output level of the selected

channel.

Using the Selected Channel section

GROUP

1 2

7 Using the Selected Channel section

66 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Here you can select or copy channels.

A INPUT/OUTPUT indicators

These indicators show whether an input channel or

output channel is selected.

B Name indicator

This indicates the name of the selected channel.

C Number indicator

This is the number of the selected channel. For stereo

channels (ST IN, FX TRN, STEREO A/B), the number

and a character of “L” or “r” will appear, depending on

whether the L or R channel is selected. If a channel is

paired, the decimal point for the lowest place will light.

For a FX RTN channel, the LED for the highest place

will light.

D [PASTE] key

E [COPY] key

These keys are used to copy and paste channel data.

When you press the [COPY] key, the data of the cur-

rently selected channel will be copied into a memory

buffer; when you press the [PASTE] key, the data in the

memory buffer will be pasted into the currently

selected channel. You can specify the parameters that

will be copied in the INPUT VIEW function CH JOB

screen (for input channels) or the OUTPUT VIEW

function CH JOB screen (for output channels).

Note

• If the buffer memory contains no data, or if the data in the

buffer memory is of a different type than the selected chan-

nel, a warning message will appear and the Paste operation

cannot be executed.

• The data in the buffer memory is lost when the power is

turned off.

F CH [DEC] key

G CH [INC] key

The CH [DEC] key decrements the currently selected

channel number, and the CH [INC] key increments it.

• Input channels 1–48

• ST IN channels 1L/1R–4L/4R

• FX RTN channels 1L/1R–4L/4R

• MIX channels 1–24

• MATRIX channels 1–8

• STEREO A channel L/R

• STEREO B channel L/R

Here you can edit delay-related parameters for the cur-

rently selected channel.

A DELAY [TIME] indicator

This indicates the currently specified delay time in

msec units. However in the case of one second, the

indicator will be “1...”.

B DELAY [TIME] encoder

This controls the delay time of the selected channel.

C DELAY [ON] key

This key switches delay on/off for the selected channel.

Channel Display

ST IN channel 1L./1r. – 4L./4r.

FX RTN channel 1.L./1.r. – 4.L./4.r.

STEREO A channel AL./Ar.

STEREO B channel BL./Br.

CHANNEL SELECT

DELAY

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 67

Using the Selected Channel section

Here you can edit the head amp, post AD conversion

attenuator, and phase parameters for the currently selected

channel. This section is available only if an input channel is

selected.

A A[GAIN/ATT] key

This key selects the parameter that is controlled by the

[GAIN/ATT] encoder (

2).

• [GAIN/ATT] key lit (Gain)

The encoder adjusts the input sensitivity of the inter-

nal head amp patched to the input channel (PM5D-

RH and DSP5D only) or of an external head amp that

supports the dedicated protocol (Yamaha AD8HR,

AD824, etc.). The range of adjustment is +10 to –62.

• [GAIN/ATT] key dark (Attenuator)

The encoder controls the post AD conversion attenua-

tor of the input channel. The range of adjustment is

–96 to +24.

Note

• Gain cannot be selected for channels to which an internal/

external head amp is not patched.

• The PAD will be switched on or off internally when the gain

of the PM5D-RH internal head amp is adjusted between –

14 dB and –13 dB. Keep in mind that noise may be gener-

ated if there is a difference between the Hot and Cold output

impedance of the external device connected to the INPUT

connector/ST IN connector when using phantom power.

• If you don’t want it to be possible to select the attenuators,

access the UTILITY function PREFERENCE 1 screen, and

turn ATT OPERATION ON PANEL off (

➥

p.206).

B [GAIN/ATT] encoder

According to the setting of the [GAIN/ATT] key (1),

this encoder controls either the input sensitivity of the

internal/external head amp patched to the input chan-

nel, or the attenuator following AD conversion.

The LEDs around the periphery will change as follows.

• [GAIN/ATT] key lit (Gain)

• [GAIN/ATT] key dark (Attenuator)

C [ø] key

This switches the phase of the selected input channel. If

this key is on, the phase will be reversed.

Here you can edit noise gate parameters for the selected

channel. This section is valid only if an input channel or ST

IN channel is selected.

A GATE GR meter

This meter indicates the amount of reduction pro-

duced by the gate of the selected channel.

B GATE [ON] key

Switches the gate on/off for the selected channel.

C GATE [ATTACK] indicator

Indicates the attack time of the gate in msec units.

D GATE [ATTACK] encoder

Specifies the attack time of the gate (the time from

when the signal exceeds the threshold until the gate

opens).

E GATE [HOLD] indicator

Indicates the hold time of the gate in msec units or sec

units (the indicator for the displayed unit will light).

F GATE [HOLD] encoder

Specifies the hold time of the gate (the time from when

the signal falls below the threshold until the gate

closes).

G GATE [DECAY] indicator

Indicates the decay time of the gate in msec units or sec

units.

GAIN/ATTENUATION/ø (Gain /

Attenuation / Phase)

➠

–

(attenuation)

(boost)

NOISE GATE

7 Using the Selected Channel section

68 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

H GATE [DECAY] encoder

Specifies the hold time of the gate (the time over which

the gate will close after the hold time has elapsed).

I GATE [THRESHOLD] encoder

Specifies the threshold level of the gate (the level at

which the gate will open or close). The gate will open

when the signal exceeds this level, and will close when

the signal falls below this level.

J GATE [RANGE] encoder

Specifies the amount of attenuation while the gate is

closed.

Here you can switch the on/off status of the signal sent

from the selected channel to the STEREO bus, and adjust

the pan.

A STEREO [PAN] encoder

The function of this encoder depends on the currently

selected channel, as follows.

B [TO STEREO] key

The function of this key depends on the currently

selected channel, as follows.

Here you can edit compressor parameters for the selected

channel. This section is available only if a channel other

than an FX RTN channel is selected.

A COMP GR meter

This meter indicates the amount of reduction pro-

duced by the compressor of the selected channel.

B COMP [ON] key

Switches the compressor on/off for the selected

channel.

C COMP [ATTACK] indicator

Indicates the attack time of the compressor in msec

units.

D COMP [ATTACK] encoder

Specifies the attack time of the compressor (the time

from when the signal exceeds the threshold level until

compression begins).

E COMP [RELEASE] indicator

Indicates the release time of the compressor in msec

units or sec units (the indicator for the displayed unit

will light).

F COMP [RELEASE] encoder

Specifies the release time of the compressor (the time

from when the signal falls below the threshold level

until compression is removed).

G COMP [RATIO] indicator

Indicates the compression ratio setting.

H COMP [RATIO] encoder

Specifies the compression ratio (the ratio at which the

input signal will be compressed when the signal

exceeds the threshold level).

I COMP [THRESHOLD] encoder

Specifies the threshold level of the compressor (the

level at which the compressor will operate). The input

signal will start being compressed when the signal

exceeds this level; compression will be removed when

the signal falls below this level.

Selected channel Function

Input channel

Adjusts the panning of the signal

sent from that channel to the STE-

REO bus.

ST IN channel

FX RTN channel

MIX channel

STEREO A/B channels

Adjusts the left/right balance of the

signal sent from the STEREO A/B

channels.

MATRIX channel No function.

Selected channel Function

Input channel

Functions as an on/off switch for

the signal sent from that channel

to the STEREO bus.

ST IN channel

FX RTN channel

MIX channel

STEREO A/B channels

No function.

MATRIX channel

STEREO

COMPRESSOR

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 69

Using the Selected Channel section

J COMP [GAIN] encoder

Specifies the gain of the signal that has passed through

the compressor.

Here you can edit high pass filter parameters for the

selected channel. This section is available only if an input

channel is selected.

A HPF [FREQUENCY] encoder

Specifies the cutoff frequency of the high pass filter.

B HPF [FREQUENCY] indicator

Indicates the currently specified high pass filter cutoff

frequency, in units of Hz.

C HPF [ON] key

Switches the high pass filter on/off.

Here you can edit equalizer parameters for the selected

channel. The equalizer structure differs as follows between

input channels and output channels.

❏ Input channels

You can use a four-band peak/dip type EQ (HIGH, HIGH

MID, LOW MID, LOW). The HIGH band can be switched

to an LPF or shelving type; the LOW band can be switched

to a shelving type.

❏ Output channels

If a MIX channel or STEREO A/B is selected, you can use

an eight-band peak/dip type EQ. (Operation is divided into

UPPER and LOWER groups of four bands each.) For

MATRIX channels, you can use a four-band peak/dip type

EQ.

For any output channel, the HIGH band can be switched

to shelving or LPF. The LOW band can be switched to

shelving or HPF. For MIX channels and STEREO A/B

channels, this can be specified for UPPER and LOWER,

allowing you to apply shelving or filtering twice.

Hint

• Input channels also provide an HPF that is independent of

the four-band EQ.

• Output channels do not have an independent HPF, but

instead allow you to switch the LOW band type to HPF.

• Switching the equalizer type to HPF or LPF can be done in

the EQ PARAM screen (

➥

p.250)

A EQ [ON] key

Switches the equalizer on/off for the selected channel.

B EQ [UPPER] key

C EQ [LOWER] key

If a MIX channel or STEREO A/B channel is selected,

these keys select the four-band group (UPPER or

LOWER) that you will edit. (The LED of the currently

selected key will light.)

If any other channel is selected, the LEDs of both keys

will be dark.

Hint

By simultaneously holding down the EQ [UPPER] key and EQ

[LOWER] key, you can return the EQ GAIN settings of the

selected channel to a flat state.

D EQ [ ] key

If this key is on, the corresponding HIGH band EQ

type will be switched to shelving. In this case, the

HIGH band EQ [Q] knob will have no function.

HPF (High Pass Filter)

EQUALIZER

45 6

7 Using the Selected Channel section

70 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

E EQ [Q] encoder

Adjusts the Q (steepness) of each band. This encoder

does nothing for bands whose EQ type is set to shelv-

ing, LPF, or HPF.

F EQ [FREQUENCY] encoder

Adjusts the center frequency (or cutoff frequency) at

which each band will be boosted or cut.

G EQ [FREQUENCY] indicator

Indicates the center frequency (or cutoff frequency) at

which boost/cut will occur, in units of kHz or Hz. (The

indicator for the displayed unit will light.)

H EQ [GAIN] encoder

Adjusts the amount of cut/boost for each band.

I [] key

If this key is on, the corresponding LOW band EQ will

be switched to shelving type. In this case, the LOW

band EQ [Q] knob will have no function.

Operations in the SELECTED CHANNEL section

The SELECTED CHANNEL section always controls the

channel that was last selected by its [SEL] key.

To select an input channel, press a [SEL] key in the INPUT

channel strip or ST IN/FX RTN channel strip. (If neces-

sary, switch the layer before pressing a [SEL] key.) To select

an output channel, press a [SEL] key in the MIX section,

MATRIX section, or STEREO A/B channel strip.

Press a [SEL] key to select the channel you

want to control.

The number and name of the currently selected chan-

nel is shown in the SELECTED CH area at the lower

left of the display, and by the name indicator and num-

ber indicator in the SELECTED CHANNEL section.

Note

If the console is cascade-connected to the DSP5D, the

MACHINE ID field will show the machine ID number.

The number shown in the number indicator is as fol-

lows. If a channel is paired, the decimal point for the

lowest place will light. For a FX RTN channel, the deci-

mal point for the highest place will light.

Hint

• In the case of stereo channels (ST IN/FX RTN channels,

STEREO A/B channels), you can switch between L/R by

pressing the same [SEL] key.

• You can also switch the channel by using the CH [DEC] key

/ CH [INC] key of the SELECTED CHANNEL section.

Use the controls of the SELECTED CHANNEL

section to edit the parameters of the selected

channel.

When you select a channel in step 1, the parameter val-

ues of that channel will be shown by the LEDs and

indicators of the SELECTED CHANNEL section.

These parameters can be edited using the controls of

the SELECTED CHANNEL section.

Hint

• Gate, compressor, and EQ/HPF operations are explained in

the second half of this chapter; refer to the appropriate sec-

tion for details.

• For details on DCA group and mute group operations, refer

to p.82, 83.

• If you operate a parameter that is selected for AUTO DIS-

PLAY in the PREFERENCE 1 screen, the screen associated

with that parameter will appear automatically.

In the same way, select other channels and

edit their parameters.

Selecting a channel and editing its

parameters

CH 1

Number of the selected channel

Name of the selected channel

Name

indicator

The name of

the selected

channel

Number

indicator

The number

of the

selected

channel

Selected channel Number indicator

Input channels 1–48 1–48

ST IN/FX RTN channels 1–4 (L/R) 1L./1r. – 4L./4r.

MIX channels 1–24 1–24

MATRIX channels 1–8 1–8

STEREO A/B channels (L/R) AL., Ar., BL., Br.

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 71

Using the Selected Channel section

Here’s how you can use the SELECTED CHANNEL sec-

tion to operate the internal compressor.

Note

The PM5D provides four types of built-in compressor; COMP

(compressor), EXPANDER (expander), COMPANDER H

(hard compander), and COMPANDER S (soft compander).

These four operate in different ways. This means that if you

want to use a compressor, you must load compressor set-

tings of the desired type from the compressor library, and then

edit the parameters as desired.

Press a [SEL] key to select the channel you

want to control.

A compressor is available for all channels except for FX

RTN channels.

In the DISPLAY ACCESS section, press the

INPUT [GATE/COMP] key (for an input chan-

nel) or OUTPUT [COMP] key (for an output

channel) several times to access the COMP

LIBRARY screen.

In the COMP LIBRARY screen you can store compres-

sor settings in the library, or recall existing data from

the library. The operations described below are the

same for the COMP LIBRARY screen of both output

channels and input channels.

Move the cursor to the scroll bar of the library

list in the lower right of the screen, and turn

the [DATA] encoder to select the library item

that you want to load. (The library item

selected in the list is highlighted.)

Numbers 001–036 for which an “R” is shown at the

right of the list contain read-only preset library items.

Numbers 001–004 contain preset library items of dif-

ferent types. It is convenient to use these library items

when you want to select a specific type. Preset library

items 001–004 are respectively of the following types.

Hint

• The type of the currently selected compressor is shown in

the COMP PARAM screen (

➥

p.253, 291).

• The COMP LIBRARY screen also provides other library set-

tings suitable for a wide variety of instruments or purposes.

Settings you edit can also be stored in the library.

• For a detailed explanation of each type of compressor, refer

to the Appendices (

➥

p.322).

After selecting a library item, click the RECALL

button located at the lower left of the library

list.

The library item you selected in step 3 will be recalled

to the channel you selected in step 1.

In the SELECTED CHANNEL section, press the

COMP [ON] key to make the LED light.

The compressor of the selected channel will be

activated.

You can use the compressor controls of the

SELECTED CHANNEL section to edit the com-

pressor parameters.

The amount of gain reduction produced by the com-

pressor is shown by the COMP GR meter in the

SELECTED CHANNEL section.

Hint

• For details on the function of the compressor controls, refer

to p.68.

• More detailed parameters for the compressor (selection of

the key-in signal, stereo link on/off, assignment to a com-

pressor link group) can be edited in the COMP PARAM

screen of the INPUT GATE/COMP function or the OUTPUT

COMP function (

➥

p.253, 291).

• You can also cause the COMP PARAM screen to appear

automatically when you operate a compressor-related con-

trol. This setting is made in the UTILITY function

PREFERENCE 1 screen (

➥

p.204).

Number Name Type

001 Comp COMP (Compressor)

002 Expand EXPANDER

003 Compander (H)

COMPANDER H (Hard com-

pander)

004 Compander (S)

COMPANDER S (Soft com-

pander)

Compressor operations

COMP LIBRARY

Scroll barRECALL button

COMP [ON] key

COMP GR meter

7 Using the Selected Channel section

72 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Here’s how you can use the SELECTED CHANNEL sec-

tion to operate the internal gate.

Note

The PM5D provides two types of built-in gating; GATE and

DUCKING. These operate in different ways. This means that if

you want to use a gate, you must load gate settings of the

desired type from the gate library, and then edit the parame-

ters as desired.

Press a [SEL] key to select the channel you

want to control.

Gate is available only for input channels or ST IN

channels.

In the DISPLAY ACCESS section, press the

INPUT [GATE/COMP] key several times to

access the GATE LIBRARY screen.

In the GATE LIBRARY screen you can store gate set-

tings in the library, or recall existing data from the

library.

Move the cursor to the scroll bar of the library

list in the lower right of the screen, and turn

the [DATA] encoder to select the library item

that you want to load. (The library item

selected in the list is highlighted.)

Numbers 001–004 for which an “R” is shown at the

right of the list contain read-only preset library items.

Numbers 001–002 contain preset library items of dif-

ferent types. It is convenient to use these library items

when you want to select a specific type. These numbers

correspond to the different types as follows.

Hint

• The type of the currently selected gate is shown in the

GATE PARAM screen (

➥

p.289).

• The GATE LIBRARY screen also provides other library set-

tings suitable for a wide variety of instruments or purposes.

You can also save your own settings in the library.

• For a detailed explanation of each type of gate, refer to the

Appendices (

➥

p.321).

After selecting a library item, click the RECALL

button located at the lower left of the library

list.

The library item you selected in step 3 will be recalled

to the channel you selected in step 1.

In the SELECTED CHANNEL section, press the

GATE [ON] key to make the LED light.

The gate of the selected channel will be activated.

You can use the gate controls of the SELECTED

CHANNEL section to edit the gate parameters.

The amount of gain reduction produced by the gate is

shown by the GATE GR meter in the SELECTED

CHANNEL section.

Note

The THRESHOLD LED will not light if the threshold level is

between –55 dB and –72 dB.

Hint

• For details on the function of the gate controls, refer to p.67.

• More detailed parameters for the gate (selection of key-in

signal, stereo link on/off) can be edited in the INPUT GATE/

COMP function GATE PARAM screen (

➥

p.289).

• You can also cause the GATE PARAM screen to appear

automatically when you operate a gate control. This setting

is made in the UTILITY function PREFERENCE 1 screen

(

➥

p.204).

Number Name Type

001 Gate GATE

002 Ducking DUCKING

Gate operations

GATE LIBRARY

Scroll barRECALL button

GATE [ON] key

GATE GR meter

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 73

Using the Selected Channel section

Here’s how you can use the SELECTED CHANNEL sec-

tion to edit the EQ (equalizer) and HPF (High Pass Filter).

EQ can be used on all input channels and all output chan-

nels. An HPF that is independent of the EQ is provided

only for input channels. However even on output chan-

nels, you can switch the LOW band type to HPF.

Press a [SEL] key to select the channel you

want to control.

Four-band EQ (HIGH, HIGH MID, LOW MID,

LOW) is provided on all input channels and on

MATRIX channels.

Eight-band EQ is provided on MIX channels and STE-

REO A/B channels. (Control is divided into UPPER

and LOWER sections of four bands each.)

In the SELECTED

CHANNEL section,

make sure that the

EQ [ON] key is on.

If you selected a MIX

channel or STEREO A/

B channel in step 1,

use the SELECTED

CHANNEL section EQ

[UPPER] key or EQ

[LOWER] key to select the UPPER or LOWER group

of four bands.

For each band, use the EQ [Q] encoder, EQ

[FREQUENCY] encoder, and [GAIN] encoder to

edit the steepness, center frequency, and gain

respectively.

Hint

If the input signal of an input channel clips because of EQ

boost, make the SELECTED CHANNEL section [GAIN/ATT]

key go dark and use the [GAIN/ATT] encoder to lower the

level.

If you want to restore the EQ of the currently

operated channel to a flat state, simulta-

neously hold down the EQ [UPPER] and EQ

[LOWER] keys of the SELECTED CHANNEL

section.

When you hold down these two keys simultaneously,

the boost/cut amount of all bands will be reset to 0 dB.

If you want to use the HIGH band or LOW

band as a shelving-type EQ, turn on the [ ]

key or [ ] key for the corresponding band.

If you want to use HPF on an input channel,

turn on the HPF [ON] key in the SELECTED

CHANNEL section.

Input channels provide an HPF that is independent of

the four-band EQ. Use the HPF [ON] key to switch the

HPF on/off, and use the HPF [FREQUENCY] encoder

to specify the cutoff frequency.

Hint

• Output channels do not provide an HPF that is independent

of the EQ, but you can switch the LOW band type to HPF, or

the HIGH band type to LPF. This change is made in the

OUTPUT EQ function EQ PARAM screen (

➥

p.250).

• For input channels you can switch the HIGH band type to

LPF. This change is made in the INPUT ø/EQ function EQ

PARAM screen (

➥

p.286).

Hint

• You can cause the associated screen to appear automati-

cally when you operate equalizer or HPF parameters in the

SELECTED CHANNEL section. This setting is made in the

UTILITY function PREFERENCE 1 screen (

➥

p.204).

• In the same way as for compressor or noise gate settings,

EQ settings can also be stored to or recalled from a dedi-

cated EQ library. Preset library items suitable for a variety of

instruments or situations are also provided.

EQ/HPF operations

EQ [UPPER]

key

EQ [LOWER]

key

EQ [ON] key

EQ [FREQUENCY]

encoder

EQ [ ] key

EQ [Q] encoder

Q [GAIN] encoder

EQ [ ] key

HPF [FREQUENCY]

encoder

HPF [ON]

key

8 Input Patch / Output Patch operations

74 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

This chapter explains how to edit the input patch and output patch settings, and how to use insert

connections and direct output.

Changing the input patch settings

The input patch section lets you assign input ports to input

channels. In the PM5D’s default state, the input patch set-

tings assign the following signals to input channels.

However, you will need to edit the input patch settings if

you want input signals from an I/O card installed in slots

1–4 or input signals from a 2TR IN DIGITAL jack to be

assigned to an input channel. Here’s how to do this.

In the DISPLAY ACCESS section, press the

INPUT [PATCH] key several times to access the

INPUT PATCH screen.

The INPUT PATCH screen is where you can patch

(assign) input ports (rear panel input jacks or input

channels of I/O cards) to input channels.

The horizontal direction of the screen shows the input

ports (i.e., patch sources), and the vertical direction of

the screen shows the input channels (i.e., patch

destinations).

If an input port is patched to an input channel, a

symbol is displayed at the intersecting grid.

Use the left/right scroll bar to display the

patch-source input port.

The horizontal direction of the screen shows the patch

source’s input port type, ID number, port number, and

the number of input channels that are assigned to it. To

view input ports that are not currently visible, use the

horizontal scroll bar or the [DATA] encoder.

You can select the following input ports.

Use the vertical scroll bar to display the patch-

destination input channel.

The vertical direction of the screen shows the patch-

destination input channels. To see channels that are

not currently visible, use the vertical scroll bar. Alterna-

tively, you can hold down the [SHIFT] key and turn

the [DATA] encoder.

The following input channels can be selected.

8 Input Patch / Output Patch

operations

Input channels 1–48 Input signals from INPUT jacks 1–48

ST IN channels 1–4

Input signals from ST IN jacks 1–4

(L/R)

FX RTN channels 1–4

Output signals of internal effects 1–4

(L/R)

INPUT PATCH

AD IN 1–48 INPUT jacks 1–48

AD ST IN 1–4 ST IN jacks 1–4 (L/R)

SLOT IN 1–4 Input channels (1–16) of slots 1–4

FX OUT 1–8 Outputs (L/R) of internal effects 1–8

2TR IN D1–D3 2TR IN DIGITAL jacks 1–3 (L/R)

2TR IN A1/A2 2TR IN ANALOG jacks 1/2

CH 1–48 Input channels 1–48

STIN1L/1R–STIN4L/4R ST IN channels 1–4 (L/R)

FXRTN1L/1R–FXRTN4L/4R FX RTN channels 1–4 (L/R)

Indicates the number of the input channel.

Indicates the name of the input channel.

Indicates the number of input ports

assigned to the input channel.

To patch an input port to an input

channel, click this grid to display a “ ”

symbol.

From the top, this shows the input port type

and ID number, the port number, and the

number of input channels currently assigned.

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 75

Input Patch / Output Patch operations

Click the grid where the desired patch-source

and patch-destination intersect.

The vertical and horizontal red lines indicate the grid

position where the cursor is located. The SELECTED

PATCH area in the upper left of the screen shows the

input port and input channel for the grid at which the

cursor is located.

When you click a grid, a window will ask you to con-

firm that you want to change the patch setting.

Click the OK button in the window.

The new patch will be finalized, and a “ ” symbol will

appear at the corresponding grid.

To cancel the patch, click the “ ” symbol once again.

Hint

• If you want to change the patch directly without having to

respond to the confirmation window, go to the UTILITY func-

tion PREFERENCE 1 screen and turn PATCH

CONFIRMATION off (

➥

p.204).

• To move the cursor location rapidly in or out of the grid, hold

down the [SHIFT] key and press the CURSOR [

√

]/[

[

†

] keys.

Note

You can patch a single input port to multiple input channels,

but you cannot patch multiple input ports to a single input

channel.

Changing the output patch settings

In the output patch section you can assign output chan-

nels to output ports. When the PM5D is in its initial state,

MIX channels 1–24 are assigned to MIX OUT jacks 1–24.

Other output channels are always connected to the follow-

ing output jacks.

However you can edit the output patch settings so that the

signals of these output channels are also sent from other

output ports in parallel. Here’s how to do this.

In the DISPLAY ACCESS section, press the

OUTPUT [PATCH] key several times to access

the OUTPUT PATCH screen.

In the OUTPUT PATCH screen you can patch (assign)

output channels to output ports. The horizontal direc-

tion of the screen shows the output ports (i.e., patch

destinations), and the vertical direction of the screen

shows the output channels (i.e., patch sources).

When the PM5D is in its default state, MIX channels

1–24, MATRIX channels 1–8, and the STEREO A

channel are patched to the output channels of slots 1–4

and the 2TR OUT DIGITAL jacks in addition to the

output jacks that are always connected. However, you

are free to change this patching.

Use the horizontal scroll bar to display the

patch-destination output port.

The horizontal direction of the screen shows the patch

destination’s output port type, ID number, port num-

ber, and the number of output channels that are

assigned to it.

You can select the following output ports.

Input port

Input channel

number

Input channel

name

MIX channels 1–24 MIX OUT jacks 1–24

STEREO A/B channels STEREO OUT jacks A/B

MATRIX channels 1–8 MATRIX OUT jacks 1–8

Monitor output L/R/C MONITOR OUT jacks L/R/C

OUTPUT PATCH

MIX OUT MIX OUT jacks 1–24

SLOT OUT 1–4

Output channels (1–16) of an I/O

card installed in slots 1–4

FX IN 1–8 Inputs (L/R) of internal effects 1–8

2TR OUT D1/D2 2TR OUT DIGITAL jacks 1–2 (L/R)

Indicates the output channel number.

Indicates the number of output ports

assigned to the output channel.

To patch an output port to an output

channel, click this grid to display a “ ”

symbol.

From the top, this area shows the output

port type, ID number, port number, and

number of assigned output channels.

8 Input Patch / Output Patch operations

76 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Use the vertical scroll bar to display the patch-

source output channel.

The vertical direction of the screen shows the patch-

source output channels.

The following output channels can be selected.

Note

For the PM5D, the CUE L/R channels are unavailable; for the

DSP5D, the MONITOR L/R/C channels are unavailable.

Click the grid where the desired patch-source

and patch-destination intersect.

The SELECTED PATCH area in the upper left of the

screen shows the output port and output channel for

the grid at which the cursor is located.

When you click a grid, a window will ask you to con-

firm that you want to change the patch setting.

Hint

If you want to change the patch directly without having to

respond to the confirmation window, go to the UTILITY func-

tion PREFERENCE 1 screen and turn PATCH

CONFIRMATION off (

➥

p.204).

Click the OK button in the window.

The new patch will be finalized, and a “ ” symbol will

appear at the corresponding grid. To cancel the patch,

click the “ ” symbol once again.

Note

You can patch an output channel to more than one output

port, but you cannot patch multiple output channels to a sin-

gle output port.

MIX 1–24 MIX channels 1–24

MATRIX 1–8 MATRIX channels 1–8

ST AL/AR STEREO A channel (L/R)

ST BL/BR STEREO B channel (L/R)

MONITOR L/R/C

(PM5D)

Monitor output (L/C/R)

CUE L/R (DSP5D) Cue output (L/R)

TALKBACK OUT Talkback output

OSC OUT Oscillator output

Output port

Output channel

number

Output channel

name

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 77

Input Patch / Output Patch operations

Inserting an external device into a channel

You can insert an effect processor or other external device into the signal route of an input channel or output channel. When

doing so, you can specify for each channel the input/output port and insert I/O point that you want to use for insertion.

When inserting an external device into a desired channel,

you can use the rear panel input/output jacks or the input/

output jacks of an I/O card installed in a slot as insert-out/

insert-in jacks.

The following diagrams show typical examples of insert

connections.

Insert connection example 1

Insert connection example 2

Insert connection example 3

If you are inserting an external digital device via a digital I/

O card as shown in “Insert connection example

3,” you

will need to synchronize the word clock of the PM5D and

the external device. Normally, we recommend that you set

the external device as a word clock slave, and make it fol-

low the PM5D’s word clock. (For details on how to set

your device as a word clock slave, refer to its manual.)

Hint

For the PM5D model, you can also use the rear panel

INSERT IN/OUT jacks to insert an external device into an

input signal, as an alternative to the method described above.

In this case, the insert I/O point is fixed at immediately before

AD conversion. Also, the steps described p.78 will not be

necessary.

Connecting an external device for

insertion

COAXIAL COAXIALAES/EBU AES/EBU AES/EBU AES/EBU

DIGITAL IN

(AES/EBU)

DIGITAL OUT

(AES/EBU)

Effect processor

MY8-DA96MY8-AD96

ANALOG OUT ANALOG IN

Effect processor

AES/EBU

MY8-AE

DIGITAL OUT

(AES/EBU)

INPUT 1/2 OUTPUT 1/2

DIGITAL IN

(AES/EBU)

Effect processor

(female) (male)

Special AES/EBU

cable for MY8-AE

8 Input Patch / Output Patch operations

78 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Here we will explain how to make insert connections,

using an example in which an external device connected to

an AD/DA card in a slot is inserted into an input channel.

However, the procedure is the same when inserting into an

output channel, the only difference being that you will be

working in a screen for output channels.

In the DISPLAY ACCESS section, press the

INPUT [PATCH] key several times to access the

INSERT PATCH screen (INPUT PATCH func-

tion) shown below.

In the left side of this screen you can select an output

port to use as insert-out, and in the right side of the

screen you can select an input port to use as insert-in.

If you want to insert into an output channel, press the

OUTPUT [PATCH] key several times to access the

OUTPUT PATCH function INSERT PATCH screen.

In the left side of the screen, click the grid at

which the output port connected to your

external device intersects the desired channel.

The procedure is the same as in the INPUT PATCH

screen or OUTPUT PATCH screen. You can select the

following output ports.

Hint

If you select GEQ IN at the left side of the screen, the identi-

cally-numbered GEQ OUT will be automatically selected at

the right side of the screen, inserting the correspondingly-

numbered GEQ module into that channel. (For details on

using the graphic EQ

➥

p.118)

In the right side of the screen, click the grid at

which the input port connected to your exter-

nal device intersects the desired channel.

You can select the following input ports.

The SELECTED PATCH area shows the channel corre-

sponding to the grid at which the cursor is located. To

the right of this are shown the input/output ports

patched to insert-out/insert-in for this channel.

Hint

To move the cursor rapidly between the grids in the left and

right sides of the screen, you can hold down the [SHIFT] key

and press the CURSOR [

√

]/[

] keys.

Note

With the steps you have taken so far, the external device has

been patched to the insert-out/insert-in of the selected chan-

nel. However, please note that the insert connection is not

actually enabled until you turn on the INSERT I/O ON/OFF

button in the INSERT/DIRECT OUT screen as described

below. As an exception to this, the INSERT I/O ON/OFF but-

ton is automatically turned on if you patch a GEQ.

Press the INPUT [PATCH] key several times to

access the INSERT/DIRECT OUT POINT screen

(INPUT PATCH function) shown below.

In the INSERT/DIRECT OUT POINT screen (INPUT

PATCH function) you can switch insert on/off for each

input channel. In this screen you can also select the

insert I/O point (the location at which the external

device will be inserted).

If you want to insert into an output channel, press the

OUTPUT [PATCH] key several times to access the

OUTPUT PATCH function INSERT PATCH screen.

MIX OUT 1–24 MIX OUT jacks 1–24

SLOT OUT 1–4

Output channels of an I/O card

installed in slots 1–4

FX IN 1–8 L/R inputs of internal effects 1–8

GEQ IN 1–12 Inputs of GEQ modules 1–12

2TR OUT 1–3 2TR OUT DIGITAL jacks 1–3 (L/R)

Patching the insert-out and insert-in

INSERT PATCH

AD IN 1–48 INPUT jacks 1–48

AD ST IN 1–4 ST IN jacks 1–4 (L/R)

SLOT IN 1–4

Input channels of an I/O card

installed in slots 1–4

FX OUT 1–8 Outputs (L/R) of internal effects 1–8

GEQ OUT 1–12 Outputs of GEQ modules 1–12

2TR IN D1–D3 2TR IN DIGITAL jacks 1–3 (L/R)

2TR IN A1/A2 2TR IN ANALOG jacks 1/2 (L/R)

Channel at which

the cursor is located

Port patched to

insert-out

Port patched to

insert-in

INSERT/DIRECT OUT POINT

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 79

Input Patch / Output Patch operations

Select one of the following as the insert I/O

point for each channel, and turn on the corre-

sponding button.

The selected point is indicated by the graphic in the

upper part of the screen.

Click the INSERT I/O ON/OFF button for the

desired channel to turn it on.

This enables the insert connection for the correspond-

ing channel.

If you selected AD IN as the insert-in, or if you selected

a slot to which an external head amp supporting the

special protocol (Yamaha AD8HR, AD824) is con-

nected, make head amp settings as necessary (➥ p.44).

PRE EQ Immediately before the EQ

POST EQ Immediately after the EQ

PRE DELAY Immediately before the delay

POST FADER Immediately after the fader

Select the insert I/O point for

each channel.

The INS symbol indicates the insert I/O point

for the channel at which the cursor is located.

These are the INSERT I/O ON/OFF buttons

that switch insert on/off for each channel.

These indicate the channel numbers.

These indicate the names of the input channels.

8 Input Patch / Output Patch operations

80 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Directly outputting the signal of an input channel

Here’s how the signal being input to an input channel or ST IN channel can be output directly from the desired output jack.

In the DISPLAY ACCESS section, press the

INPUT [PATCH] key several times to access the

DIRECT OUT PATCH screen (INPUT PATCH

function) shown below.

In this screen you can select the output port that will

directly output the input signal of an input channel or

ST IN channel. You can select the following output

ports.

Click the grid at which the desired channel

and output port intersect.

The procedure is the same as in the INPUT PATCH

screen or OUTPUT PATCH screen. The SELECTED

PATCH area at the upper left of the screen shows the

channel and output port corresponding to the grid at

which the cursor is located.

Note

With the procedure up to this point, the selected channel and

output port are now patched. However, please note that direct

output is not actually enabled until you turn on the DIRECT

OUT ON/OFF button in the INSERT/DIRECT OUT screen

described below.

Press the INPUT [PATCH] key several times to

access the INSERT/DIRECT OUT POINT screen

(INPUT PATCH function) shown below.

In the INSERT/DIRECT OUT POINT screen (INPUT

PATCH function) you can switch direct output on/off,

and select the direct out point (the location from which

the signal is taken for direct output).

Choose the direct out point for each channel

from the following choices, and turn on the

appropriate button.

The selected point is indicated by the graphic in the

upper part of the screen.

Click the DIRECT OUT ON/OFF button for the

desired channel to turn it on.

This enables direct output for the corresponding

channel.

SLOT OUT 1–4

Output channels of an I/O card

installed in slots 1–4

2TR OUT D1–D3 2TR OUT DIGITAL jacks 1–3 (L/R)

DIRECT OUT PATCH

PRE ATT Immediately before the attenuator

PRE HPF Immediately before the HPF

PRE EQ

Immediately before the EQ (immedi-

ately after the PRE EQ of the

INSERT I/O)

PRE FADER Immediately before the fader

POST ON Immediately after the [ON] key

INSERT/DIRECT OUT POINT

Select the direct out point

for each channel.

The “D” symbol indicates the direct out point

for the channel at which the cursor is located

Switch direct out on/off

for each channel.

These indicate the number of the input channels.

These indicate the name of the input channels.

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 81

Grouping and linking

This chapter explains DCA Groups and Mute Groups which let you control the level or muting of

multiple channels simultaneously, and EQ Link and Compressor Link which let you link EQ or

compressor parameters of multiple channels.

About DCA Groups and Mute

Groups

You can use eight DCA groups and eight mute groups to

control multiple channels simultaneously.

DCA groups allow the level of multiple channels to be con-

trolled together by the DCA faders 1–8 of the top panel

DCA strip. A single DCA fader will control the level of

channels belonging to the same DCA group while main-

taining the level difference between the channels. This

provides a convenient way in which drum mics can be

grouped.

DCA groups 1–6 are for input channels only, but DCA

groups 7/8 can be used with both input channels and out-

put channels. Both types of channel can exist in an

identically-numbered group.

Mute groups allow multiple channels to be switched on/off

simultaneously by the SCENE MEMORY [1]–[8] keys in

the SCENE MEMORY section of the top panel. You can

use this to cut out multiple channels simultaneously.

Mute groups 1–8 can be used with both input channels

and output channels. Both types of channel can exist in an

identically-numbered group.

Items in the ASSIGN MODE

section

The ASSIGN MODE section lets you use the panel to

assign channels to DCA groups or mute groups.

A ASSIGN MODE [DCA] key

This key lets you assign channels to DCA groups 1–8.

While this key is blinking, you can use the [CUE] key

of each channel to assign that channel to the currently

selected DCA group.

B ASSIGN MODE [MUTE] key

This key lets you assign channels to mute groups 1–8.

While this key is blinking, you can use the [CUE] key

of each channel to assign that channel to the currently

selected mute group.

Items in the DCA strip

The DCA strip is where you control DCA groups 1–8.

A Name indicator

This indicates the name assigned to each DCA group.

B DCA [MUTE] key

This switches DCA group muting on/off. If you turn

this key on (LED lit), channels assigned to that DCA

group will be muted.

C DCA [NOMINAL] LED

This LED will light when the corresponding DCA fader

is at the 0 dB position.

D DCA fader

This fader adjusts the level of the DCA group.

E DCA [RCL SAFE] LED

If Recall Safe is enabled for a DCA group, the corre-

sponding LED will light.

9 Grouping and linking

9 Items in the DCA strip

82 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

F DCA [CUE] key

This key is used to cue-monitor all channels assigned to

that DCA group.

Using DCA Groups

Here we explain how to assign channels to DCA groups and use the DCA faders to control them.

From the panel, you can assign channels to DCA groups

either by selecting a specific channel and specifying the

DCA group to which it will belong, or by selecting a spe-

cific DCA group and specifying the channels that will

belong to that DCA group.

❏ To select the DCA groups to which a

speciﬁc channel will belong

Press a [SEL] key to select the channel for

which you want to make assignments.

In the SELECTED CHANNEL section, press a

DCA [1]–[8] key to select the DCA group to

which the channel will be assigned (you may

select more than one DCA group).

The LEDs will light for DCA [1]–[8] key(s) that are

turned on. If an input channel is selected, its corre-

sponding DCA assign LED(s) in the channel strip will

also light.

Select the DCA group(s) for other channels in

the same way.

❏ To select the channels that will belong

to a speciﬁc DCA group

In the ASSIGN MODE section, press the

ASSIGN MODE [DCA] key.

The ASSIGN MODE [DCA] key will blink. The [DCA]

key of the FADER MODE section will also blink. While

this key is blinking, you can use the [CUE] key of each

channel to assign that channel to a DCA group.

Press a DCA [CUE] key in the DCA strip to

select the DCA group (1–8) to which you want

to assign channels.

Press the [CUE] key of input channels / output

channels (you may select more than one) to

assign them to the selected DCA group.

If a DCA group 1–6 is selected, you can select only

input channels. If a DCA group 7/8 is selected, you can

select input channels and output channels. If an input

channel is selected, its corresponding DCA assign

LED(s) in the channel strip will also light.

Assign channels to other DCA groups in the

same way.

When you have finished making assignments,

press the ASSIGN MODE section ASSIGN

MODE [DCA] key to make its LED go dark.

The FADER MODE section [DCA] key will also stop

blinking, and return to its previous state.

Hint

• You can also assign channels to DCA groups from within the

display. Input channel DCA assignments are made in the

INPUT DCA/GROUP function DCA GROUP ASSIGN

screen (

➥

p.296), and output channel DCA assignments are

made in the OUTPUT DCA/GROUP function DCA GROUP

ASSIGN screen (

➥

p.258).

• DCA group settings are saved as part of the scene.

Assigning channels to DCA groups

DCA [1]–[8] keys

DCA assign LEDs

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 83

Grouping and linking

Here’s how you can use the DCA strip to control DCA

groups.

In the FADER MODE section, make sure that

the FADER MODE [DCA] key LED is lit.

The FADER MODE section selects the function of the

DCA strip faders. When the FADER MODE [DCA]

key LED is lit, you can use the faders of the DCA strip

to control DCA groups 1–8.

Use the faders of the channel strip to adjust

the relative levels between the channels

belonging to the DCA group you want to use.

Operate the DCA fader for the DCA group you

want to use.

The level of the channels assigned to that DCA fader

will change while preserving the level differences you

established in step 2.

If you want to mute a DCA group, press the

[MUTE] key for that DCA group in the DCA

strip.

The [MUTE] key will light, and muting will be turned

on for channels belonging to that DCA group (the

same state as if the faders were lowered to –∞ dB). At

this time, the name indicator for that DCA group will

be dimmed.

Hint

If desired, you can cause the DCA assign LEDs of the corre-

sponding input channels to blink while the DCA group is

muted. To do so, turn on the DCA/MUTE FLASH INDICATE

setting in the PREFERENCE 1 screen (UTILITY screen).

To un-mute a DCA group, press the lit [MUTE]

key in the DCA strip.

Using mute groups

This section explains how to assign channels to mute groups and use the panel keys to control them.

From the panel, you can assign channels to mute groups

either by selecting a specific channel and specifying the

mute groups to which that channel will belong, or by

selecting a specific mute group and specifying the channels

that will belong to that mute group.

❏ To select the mute groups to which a

speciﬁc channel will belong

Press a [SEL] key to select the channel for

which you want to make assignments.

In the SELECTED CHANNEL section, use the

MUTE [1]–[8] keys to select the mute group to

which the channel will be assigned (you may

select more than one mute group).

The LEDs will light for MUTE [1]–[8] key(s) that are

turned on. If an input channel is selected, its corre-

sponding mute assign LED(s) in the channel strip will

also light.

Select the mute group(s) for other channels in

the same way.

Controlling DCA groups

FADER MODE [DCA] key

Assigning channels to mute groups

MUTE [1]–[8] keys

Mute assign LEDs

9 Items in the DCA strip

84 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

❏ To select the channels that will belong

to a speciﬁc mute group

In the ASSIGN MODE section, press the

ASSIGN MODE [MUTE] key.

The ASSIGN MODE [MUTE] key will blink. In the

SCENE MEMORY section, the MUTE MASTER LED

will also blink. While this key is blinking, you can use

the [CUE] key of each channel to assign that channel to

a mute group.

In the SCENE MEMORY section, use the SCENE

MEMORY [1]–[8] keys to select the mute group

(1–8) for which you want to make

assignments.

While the ASSIGN MODE [MUTE] key is blinking,

you can use the SCENE MEMORY [1]–[8] keys to

select the mute group for which you will make assign-

ments. Press one of these keys; the LED of that key will

blink.

Press the [CUE] key of input channels / output

channels (you may select more than one) to

assign them to the selected mute group.

The [CUE] key will light, and that channel will be

assigned to the selected mute group.

Both input channels and output channels can be

assigned to mute groups 1–8.

Assign channels to other mute groups in the

same way.

When you have finished making assignments,

press the ASSIGN MODE section ASSIGN

MODE [MUTE] key to make its LED go dark.

The SCENE MEMORY section MUTE MASTER/

DIRECT RECALL LED will also return to its previous

state.

Hint

• You can also assign channels to mute groups from within

the display. Input channel assignments are made in the

INPUT DCA/GROUP function MUTE GROUP ASSIGN

screen (

➥

p.297), and output channel assignments are

made in the OUTPUT DCA/GROUP function MUTE

GROUP ASSIGN screen (

➥

p.259).

• Mute group assignments are saved as part of the scene.

Here’s how you can use the SCENE MEMORY [1]–[8]

keys of the SCENE MEMORY section to switch muting

on/off for mute groups 1–8.

Turn on the MUTE MASTER button located in

the lower right of the display.

The DIRECT RECALL button and MUTE MASTER

button located in the lower right of the display select

the function of the SCENE MEMORY [1]–[8] keys.

• When the DIRECT RECALL button is on

The SCENE MEMORY [1]–[8] keys will directly recall

the scene that is assigned to each key.

• When the MUTE MASTER button is on

The SCENE MEMORY [1]–[8] keys will switch mut-

ing on/off for mute groups 1–8.

Press the SCENE MEMORY [1]–[8] key for the

mute group you want to mute.

The key LED will light, and all channels belonging to

the selected mute group will be muted (the same state

as when the [ON] key is turned off). You can turn on

more than one key to mute multiple mute groups.

To un-mute a mute group, press a lit SCENE

MEMORY [1]–[8] key.

Hint

• The mute group mute on/off status is saved in the scene.

However, you can also use the Recall Safe function to

exclude the mute group status from scene recall.

• If desired, you can cause the MUTE assign LEDs of the cor-

responding input channels to blink while the mute group is

muted. To do so, turn on the DCA/MUTE FLASH INDICATE

setting in the PREFERENCE 1 screen (UTILITY screen).

If necessary, channels belonging to a mute group can be

temporarily excluded from mute group operations (Mute

Safe).

Press a [SEL] key to select the channel you

want to exclude from mute groups.

In the SELECTED CHANNEL section, press the

[MUTE SAFE] key to make the LED light.

Mute Safe will be enabled for the corresponding chan-

nel. (In the case of an input channel, the [MUTE

SAFE] LED in the channel strip will light.) In this state,

muting an applicable mute group will not affect that

channel.

To defeat Mute Safe, press the SELECTED

CHANNEL section [MUTE SAFE] key once again

to make the LED go dark.

Hint

Mute Safe settings are not saved in the scene. They will

remain effective until you manually defeat them.

Controlling mute groups

DIRECT RECALL button

MUTE MASTER button

Using the Mute Safe function

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 85

Grouping and linking

Using EQ Link and Compressor Link

EQ Link and Compressor Link are functions that respectively link the EQ parameters or compressor parameters of multiple

channels. Editing the EQ or compressor parameters of any channel belonging to a link group will similarly edit the other

channels in that link group.

In the DISPLAY ACCESS section, press the

INPUT [DCA/GROUP] key (for an input chan-

nel) or OUTPUT [GROUP] key (for an output

channel) to access one of the following

screens.

• INPUT DCA/GROUP function EQ LINK ASSIGN

screen

Assign EQ link groups (1–8) for input channels

• INPUT DCA/GROUP function COMP LINK

ASSIGN screen

Assign compressor link groups (1–8) for input

channels

• OUTPUT DCA/GROUP function EQ LINK ASSIGN

screen

Assign EQ link groups (A–F) for output channels

• OUTPUT DCA/GROUP function COMP LINK

ASSIGN screen

Assign compressor link groups (A–F) for output

channels

In each screen, the channels (assignment source) are

listed horizontally, and the link group number or

alphabetical character (assignment destination) are

listed vertically.

Hint

The EQ link groups and compressor link groups are indepen-

dent for input channels and output channels.

EQ LINK ASSIGN

COMP LINK ASSIGN

EQ LINK ASSIGN

COMP LINK ASSIGN

9 Items in the DCA strip

86 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Click the grid at which the desired channel

(assignment source) intersects the desired link

group (assignment destination).

A “ ” symbol will appear at the corresponding grid.

To cancel the assignment, click the “ ” symbol once

again.

In the case of output channel EQ link groups, MIX

channels and STEREO A/B channels can be assigned

only to groups A–F, and MATRIX channels can be

assigned only to groups G/H. (Unavailable grids are

grayed-out.)

If another channel is already assigned to the assign-

ment-destination group, the EQ and compressor

parameters of the previously-assigned channel will be

copied to the channel that is added later, causing the

settings to be the same.

If you want to use the [CUE] key of each chan-

nel to assign it to a link group, click the SET BY

CUE button for the corresponding link group

in the screen to turn it on.

While the SET BY CUE button is on, you can use the

channel [CUE] keys to set or cancel link group

assignments.

Note

• The SET BY CUE button can be turned on for only one link

group.

• When you switch to a different screen, the SET BY CUE but-

ton that was turned on will automatically be defeated.

When you have finished making link group

assignments, operate the EQ or compressor

parameters of a channel belonging to a link

group.

The EQ or compressor parameters of channels belong-

ing to the same link group will follow your editing.

Hint

Link group settings are saved as part of the scene.

Note

The STEREO LINK button and KEY IN SOURCE settings are

not linked even for channels belonging to the same compres-

sor link group.

SET BY CUE button

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 87

Scene memory

This chapter explains how to store and recall the PM5D’s mix parameters as “scenes.”

About scenes

The PM5D can store and recall the current state of its mix parameters as a “scene.” Scenes are assigned a scene number of

000–500. Scene 000 is read-only, and cannot be overwritten. Other scene numbers may be rewritten freely.

A scene contains the settings of the panel controls (except

for the TALKBACK section, CUE/MONITOR section, and

the AD IN section of the PM5D model) as well as the set-

tings of the functions and screens listed below.

• INPUT function settings

• OUTPUT function settings

• EFFECT PARAM screen settings

• GEQ PARAM screen settings

• SELECTIVE RECALL screen (SCENE function)

settings

• FADE TIME screen (SCENE function) settings

• MIXER SETUP screen (SYS/W.CLOCK function)

settings

• HA screen (SYS/W.CLOCK function) settings

However, input patch, output patch, and HA (head amp)

settings are saved in the corresponding library, and the

scene contains only a library number that links to these

saved settings.

For example if the input patch, output patch, and HA

(head amp) settings have been edited when you store a

scene, the changes will be stored in the corresponding

library, and the library number of these stored library

items will be stored in the scene.

Hint

You can choose how the changes will be stored in the library;

they can either be stored in a new unused library number, or

overwritten onto the existing library number (

➥

p.89).

When you recall a scene, the input patch, output patch,

and HA (head amp) library numbers linked to that scene

will be recalled simultaneously.

For each scene, you can specify whether to enable linking

to these libraries (➥ p.175). For example if you turn off

linking to the HA library for a certain scene, recalling that

scene will not update the HA settings.

Note

By “head amp settings” we mean settings for the internal head

amps of the PM5D-RH model and for an external head amp

device that supports the special protocol (e.g., Yamaha

AD8HR or AD824). The settings of the AD IN section of the

PM5D model are not included.

Hint

If the PM5D and DSP5D are cascade-connected, storing a

scene will cause the scene data to be stored in each the

PM5D and in the DSP5D.

When a scene is recalled, the same scene number is recalled

on all PM5D/DSP5D units.

10 Scene memory

00 Initial Data

10 InPatch #1

00 Initial Data

10 OutPatch #1

00 Initial Data

10 HA #1

000 Initial Data

010 Music #1

Current scene

Scene memory

Input patch

settings

Output patch

settings

Internal/external

head amp settings

Input patch library

Output patch library

HA library

• Storing a scene

000 Initial Data

010 Music #1

00 Initial Data

10 InPatch #1

00 Initial Data

10 OutPatch #1

00 Initial Data

10 HA #1

• Recalling a scene

Current scene

Scene memory

Input patch

settings

Output patch

settings

Internal/external

head amp settings

Input patch library

Output patch library

HA library

10 Scene memory

88 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Items in the SCENE MEMORY section

The SCENE MEMORY section lets you store and recall mix parameters as scene memories. Mute operations for mute groups

1–8 are also performed in this section.

A SCENE MEMORY [1]–[8] keys

The function of these keys will depend on the selection

of the DIRECT RECALL button and MUTE MASTER

button in the lower right of the display.

• When the DIRECT RECALL button is on

SCENE MEMORY [1]–[8] keys operate as Direct

Recall keys that directly recall the eight scenes assigned

to these keys.

• When the MUTE MASTER button is on

SCENE MEMORY [1]–[8] keys operate as Mute Mas-

ter keys that switch muting on/off for mute groups 1–8.

B [DIRECT RECALL]/[MUTE MASTER]

indicators

These indicators indicate the currently selected func-

tion of the SCENE MEMORY [1]–[8] keys (

1).

C SCENE MEMORY [PREVIEW] key

This key selects either NORMAL mode or PREVIEW

mode as the operation when you recall a scene. PRE-

VIEW mode is selected if this key LED is lit; NORMAL

mode is selected if it is dark. Operation will differ as

follows according to the selected mode.

• NORMAL mode

This mode lets you store and recall scenes as usual.

When you recall a scene in this mode, the current scene

will be overwritten by the settings of the newly recalled

scene.

• PREVIEW mode

This mode lets you preview the settings of a scene

stored in memory without affecting the signal process-

ing of the current scene. When you recall a scene in this

mode, the mix parameter values of that scene will be

shown in the PM5D’s panel, but the internal signal

processing will remain as it was before the recall.

When you operate the panel keys or encoders at this

time, the panel display will change but internal signal

processing will not be affected. If desired, you can save

the edited content in the desired scene number or

library number.

D Scene number indicator

This indicate shows the number (000–500) of the scene

that is selected for store or recall.

E SCENE MEMORY [UNDO] key

This key cancels the most recently-executed scene recall

operation. If you have accidentally recalled an

unwanted scene, you can press this key to return to the

state prior to recalling the scene.

F SCENE MEMORY [RECALL] key

This key recalls the scene whose number is shown in

the scene number indicator (

4).

G SCENE MEMORY [π]/[†] keys

These keys increment or decrement the number dis-

played in the scene number indicator (

4). However if

the SCENE screen BLANK SKIP button is turned on,

you will only be able to select numbers in which a scene

is actually stored.

H SCENE MEMORY [STORE] key

This key stores the current scene into the number

shown by the scene number indicator (

4).

DIRECT RECALL button

MUTE MASTER button

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 89

Scene memory

Using scene memories

Here’s how to store the current mix settings (the current

scene) into a scene memory.

Note

Before you continue with the following procedure, make sure

that the SCENE MEMORY section SCENE MEMORY [PRE-

VIEW] key is off (dark). (If it is on, turn it off.)

Use the PM5D’s panel controls to set the mix

parameters as desired.

Use the SCENE MEMORY [π]/[†] keys to

select the store-destination scene number.

When you select a new scene number, the scene num-

ber and name shown at the top of the display and the

scene number shown in the scene number indicator of

the SCENE MEMORY section will blink. This blinking

indicates that the settings of the indicated scene differ

from the currently-set mix parameters.

Press the SCENE MEMORY [STORE] key.

The SCENE STORE window will appear, allowing you

to assign a title to the scene and store it. This window

shows the following information.

Use the SCENE TITLE area to assign a name to

the scene. (For details on how to input text

➥ p.30)

As desired, specify the library numbers in

which the input patch, output patch, and HA

settings will be stored.

To specify a store-destination library number, scroll

the input patch, output patch, or HA library list, and

click the desired number. (The number currently

selected as the store-destination is highlighted.) The

library number you select here is saved as part of the

scene.

The default selection of store-destination will depend

on the setting in the DEFAULT EDIT LIBRARY NO.

area.

• If the NEW button is on

The lowest of the unused library numbers will be

selected.

• If the OVERWRITE button is on

The number from which the library was originally

recalled will be selected. (If this was a read-only library

item, the lowest-numbered unused library number will

be selected.)

Click the STORE button in the window.

A message will ask you to confirm the store operation.

Click the OK button.

The current settings will be stored to the scene number

you selected in step 2, and the upper part of the screen

and the scene number indicators will stop blinking. If

any changes have been made to the input patch, out-

put patch, and HA settings used by this scene, they will

be stored in the corresponding library number.

Storing a scene

Scene number and name will blink

Scene number

will blink

An “EDIT” indicator appears here if the library settings have

been modiﬁed from the state in which they were last stored.

SCENE TITLE area, where you can rename the scene.

As the default choice in which edited library

settings will be stored when you store a scene,

choose either NEW (select an unused library)

or OVERWRITE (select the original library).

HA library

list

Input Patch

library list

Output Patch

library list

10 Scene memory

90 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Here’s how to recall a stored scene from memory.

Note

Before you continue with the following procedure, make sure

that the SCENE MEMORY section SCENE MEMORY [PRE-

VIEW] key is off (dark). (If it is on, turn it off.)

Use the SCENE MEMORY [π]/[†] keys to

select the scene number that you want to

recall.

When you select a new scene number, the scene num-

ber and name shown at the top of the display and the

scene number shown in the scene number indicator of

the SCENE MEMORY section will blink.

Press the SCENE MEMORY [RECALL] key.

A message in the display will ask you to confirm the

recall operation. When you click the OK button, the

scene number you selected in step 1 will be recalled.

If input patch, output patch, and HA libraries are

linked to that scene, the correspondingly numbered

libraries will also be recalled.

Hint

If desired, you can disable the link between the scene and

these libraries, so that specific libraries will not be updated

when you recall that scene.

Using PREVIEW mode

Preview mode lets you check or edit the settings of a scene stored in memory without affecting the signal processing of the

current scene. When you recall a scene in this mode, the settings of the newly recalled scene will appear on the PM5D’s panel,

but the internal signal processing will remain as it was prior to the recall.

During an actual performance, it can be convenient to use this to check the content of the scene you intend to recall next, or to

make minor changes to a scene and then store it.

In the SCENE MEMORY section, turn on the

SCENE MEMORY [PREVIEW] key.

The key LED will light, and the SCENE MEMORY sec-

tion will operate in PREVIEW mode. At this time, the

scene indicator at the top of the display will turn red,

and the “PREVIEW” indicator will appear.

While in PREVIEW mode, operating the knobs,

encoders, and other controls (except for the TALK-

BACK section, CUE/MONITOR section, and the AD

IN section of the PM5D model) will not affect the

audio signal processing.

Use the SCENE MEMORY [π]/[†] keys to

select the scene number that you want to

recall.

The scene number will light in the scene number

indicator.

Press the SCENE MEMORY [RECALL] key.

Only the setting values of the scene you selected in step

2 will be loaded and shown in the PM5D’s panel LEDs

and display. However, the internal signal processing of

the system will remain unchanged as it was prior to the

Recall operation.

If desired, you can access a specific channel in the

SELECTED CHANNEL section, or access a specific

screen in the display to examine the values in detail.

If desired, use the controls of the console to

edit the settings.

Operating a panel control in PREVIEW mode will edit

the settings of the scene you recalled in step 3, but will

not affect the PM5D’s internal signal processing.

If you want to store the changes you made in

step 4, select the scene number in which you

want to store the scene, and press the SCENE

MEMORY [STORE] key.

The settings you edited in step 4 will be stored into

memory.

To return the SCENE MEMORY section to

NORMAL mode operation, press the SCENE

MEMORY [PREVIEW] key to make the key LED

go dark.

Note

• PREVIEW mode applies to all parameters included in scene

memory, all parameters included in the INPUT PATCH and

OUTPUT PATCH functions, and HA parameters. PREVIEW

mode does not apply to parameters other than these.

• Even while you are in PREVIEW mode, recall operations in

the EVENT LIST screen or via MIDI messages will apply to

the current scene. While in PREVIEW mode, operations of

parameters that can be edited in the USER DEFINED

screen will generally apply to PREVIEW mode, not to the

current scene.

Recalling a scene

“PREVIEW” indicator

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 91

Scene memory

Using the Auto Store function

With the PM5D’s default settings, pressing the SCENE MEMORY [STORE] key will open the SCENE STORE window where

you can name the scene and store it. If you enable the Auto Store function, you can execute the Store operation simply by

pressing the SCENE MEMORY [STORE] key twice. Here’s the procedure.

In the DISPLAY ACCESS section, press the

[UTILITY] key several times to access the PREF-

ERENCE 1 screen shown below.

The PREFERENCE 1 screen is where you can make

various default settings for the PM5D.

In the STORE/RECALL area at the upper left of

the screen, turn on the AUTO STORE button.

The Auto Store function is now enabled. When you

press the SCENE MEMORY [STORE] key once, the

SCENE STORE window will appear as usual; press the

key once again to execute the Store operation. If you

rapidly press the key twice, the Store operation will be

executed before the SCENE STORE window appears.

Note

Note that if the STORE CONFIRMATION button is turned on

in the STORE/RECALL area of this PREFERENCE 1 screen,

a window will ask you to confirm the Store operation even if

Auto Store is enabled. If you don’t want any windows to

appear, turn off the STORE CONFIRMATION button as well.

Using the Direct Recall function

If you assign frequently-used scenes to the SCENE MEMORY [1]–[8] keys of the SCENE MEMORY section, you will be able

to recall these scenes with a single keystroke.

In the DISPLAY ACCESS section, press the

[SCENE] key several times to access the SCENE

screen shown below.

In the SCENE screen you can use the DIRECT

RECALL ASSIGN list shown in the lower middle of the

screen to assign scene numbers to the SCENE MEM-

ORY [1]–[8] keys.

Use the DIRECT RECALL ASSIGN list to assign a

scene number to a SCENE MEMORY [1]–[8]

key.

Move the cursor to the left-hand field of the DIRECT

RECALL ASSIGN list and turn the [DATA] encoder or

click the / buttons to select a scene number; the

scene name will appear in the field at right.

Assign scene numbers to other keys in the

same way.

In the KEY MODE area at the right side (or

lower right) of the screen, make sure that the

DIRECT RECALL button is turned on. (If it is

off, click the DIRECT RECALL button.)

When the DIRECT RECALL button is on, the SCENE

MEMORY section [DIRECT RECALL] LED will light,

and the SCENE MEMORY [1]–[8] keys will operate as

Direct Recall keys.

PREFERENCE 1 AUTO STORE button

SCENE

DIRECT RECALL

button

DIRECT RECALL ASSIGN list

Scene name is

displayed

10 Scene memory

92 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

In the SCENE MEMORY section of the console,

press one of the SCENE MEMORY [1]–[8] keys.

The LED of the corresponding key will light, and the

scene assigned to that key will be recalled.

Using the Selective Recall function

“Selective Recall” is a function that lets you restrict the parameters or channels that will be updated when you recall a specific

scene, or, conversely, specify for each scene parameters or channels that will be excluded from recall operations.

Hint

As a function similar to Selective Recall, there is also a “Recall

Safe” function that lets you select channels and parameters to

be excluded from recall operations (

➥

p.94). However it dif-

fers from Selective Recall in that Recall Safe settings apply to

all scenes.

In the DISPLAY ACCESS section, press the

[SCENE] key several times to access the SELEC-

TIVE RECALL screen shown below.

In the SELECTION MODE area in the upper

middle of the screen, choose one of the fol-

lowing two selection modes to specify how the

SELECTIVE RECALL screen will operate.

• SAFE PARAMETER mode

Specify channels/parameters that will be excluded from

Recall operations.

• RECALL PARAMETER mode

Specify channels/parameters that will be affected by

Recall operations.

When you click a button to change the mode, a confir-

mation window will appear. Immediately after you

switch modes, all channels/parameters will be subject

to recall.

Use the buttons in the screen to select the

parameters/channels that will be subject to

recall (or excluded from recall).

The SELECTIVE RECALL screen is divided into three

areas. From the left, these areas let you make settings

for input channels, output channels, and other param-

eters. The buttons in the screen correspond to

parameters and channels as follows.

❏ Input channels / Output channels

A SAFE ON/OFF

RECALL ON/OFF

The functions and names of these buttons will depend

on the currently-chosen SELECTION MODE.

• SAFE PARAMETER mode

The buttons will function as SAFE ON/OFF buttons to

select the channels that will be excluded from Recall.

• RECALL PARAMETER mode

The buttons will function as RECALL ON/OFF but-

tons to select the channels that will be subject to Recall.

B Parameter matrix grid

Here you can select the parameters that will be

excluded from (or subject to) Recall. If the ALL button

is on, all parameters will be excluded from (or subject

to) Recall.

C SET ALL

Turns on all buttons for all input channels/output

channels or for the corresponding parameter.

D CLEAR ALL

Turns off all buttons for all input channels/output

channels or for the corresponding parameter.

SELECTIVE RECALL SELECTION MODE area

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 93

Scene memory

❏ Other parameters

A DCA/GEQ/EFFECT

These buttons specify whether DCA groups, GEQ

modules, and internal effects will be excluded from (or

subject to) Recall.

Note

DCA groups provide a WITH NAME button. This button

excludes the DCA group name from the recall operation (or

selects it as the object of recall).

B MUTE MASTER

This button specifies whether the Mute Master key on/

off status will be excluded from (or subject to) Recall.

C MIDI REMOTE (PM5D only)

These buttons specify whether MIDI remote layers A–

D will be excluded from (or subject to) Recall.

D PLUG-IN (PM5D only)

These buttons specify whether the Waves plug-in DSP

cards Y96K installed in slots 1–4 will be excluded from

(or subject to) Recall.

E SET ALL

This button turns on all buttons for parameters 1–4.

F CLEAR ALL

This button turns off all buttons for parameters 1–4.

In the upper left of the screen, switch the

SELECTIVE RECALL ENABLED/DISABLED but-

ton to ENABLED.

When this button is set to ENABLED, the Selective

Recall function will apply to subsequently-stored

scenes.

Store the current scene.

The settings of the SELECTIVE RECALL screen will be

saved as part of the scene. When you recall this scene,

only the selected channels/parameters will be excluded

from (or subject to) Recall.

Note

• If you edit the settings of the SELECTIVE RECALL screen,

you must store that scene in order to make your changes

effective.

• Recall Safe and Selective Recall can be used together.

Channels/parameters excluded from recall operations by

either Recall Safe or Selective Recall (or both) will not be

recalled.

10 Scene memory

94 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Using the Recall Safe function

“Recall Safe” is a function that excludes only specific parameters/channels from Recall operations. This differs from the Selec-

tive Recall settings (➥ p.92) made for individual scenes in that Recall Safe settings are common to all scenes.

In the DISPLAY ACCESS section, press the

[SCENE] key several times to access the

RECALL SAFE screen shown below.

Use the buttons in the screen to select the

parameters/channels that will be excluded

from Recall operations.

The function of the buttons in the screen and the pro-

cedures are the same as in the SELECTIVE RECALL

screen (when SAFE PARAMETER mode is selected),

except for the fact that HA (Head Amp) SAFE ON/

OFF button is added as a parameter in the INPUT

SAFE PARAMETER area.

The [RCL SAFE] indicator of the channel strip will

light for input channels, STEREO A/B channels, and

DCA groups for which Recall Safe is turned on.

Hint

• In the RECALL SAFE screen, clicking the parameter matrix

grid will display a “ ” symbol with a “G” character in the

center. This “G” indicates that the setting is global, and

applies to all scenes.

• If desired, you can copy and paste Selective Recall settings

from the currently selected scene into the RECALL SAFE

screen (

➥

p.183).

• If you scroll the scroll bar downward, you will see that the

CH column of the SAFE PARAMETERS area shows not

only input channels but also input ports. If you set the HA of

a certain input port to Recall Safe, the HA of the correspond-

ing channel will also be set to Recall Safe. Even if they are

assigned to multiple channels, the HA Recall Safe settings

for corresponding input ports/channels will be linked.

• If necessary, you can turn on the HA+CH button in the

SAFE KEY MODE SELECT area, so that when recall safe is

turned on/off using the panel [RECALL SAFE] key or the

RECALL SAFE button in the CH VIEW screen (INPUT

VIEW function), recall safe will be also be turned on/off for

the HA patched to the corresponding channel.

• Separately from the conventional Recall Safe functionality,

the OUTPUT ISOLATION field allows you to specify output

channels and parameters excluded from recall to be memo-

rized in SETUP memory (which is not subject to memory

card load operations) (

➥

p.182).

If you want to use the panel to switch Recall

Safe on/off for a channel, use the [SEL] key to

select a channel and then press the SELECTED

CHANNEL section [RECALL SAFE] key to make

the key LED light.

Recall Safe will be turned on for the corresponding

channel.

Note

By default, ALL is selected as the parameters that will be

excluded from recall. This means that if you turn on Recall

Safe from the panel, the Recall Safe setting will affect all

parameters of the channel(s) for which it is turned on.

After you have finished making Recall Safe settings and

you recall a scene, only the selected channels/parame-

ters will be excluded from the Recall operation.

Note

Recall Safe and Selective Recall can be used together. Chan-

nels/parameters excluded from recall operations by either

Recall Safe or Selective Recall (or both) will not be recalled.

RECALL SAFE

[RECALL SAFE] key

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 95

Scene memory

Using the Fade function

“Fade” is a function that smoothly changes fader and pan to their new values over a specified duration when you recall a

scene. The settings of the Fade function are made independently for each scene.

In the DISPLAY ACCESS section, press the

[SCENE] key several times to access the FADE

TIME screen shown below.

In this screen you can select the channels that will use

the Fade function, and specify the fade time and start

offset time.

In the upper left of the screen, click the FAD-

ING ENABLED/DISABLED button to select

ENABLED.

When the FADING ENABLED/DISABLED button is

set to ENABLED, the Fade function will be enabled for

the faders in the current scene.

In the upper right of the screen, make sure

that the FADE TIME button is on.

The FADE TIME/START OFFSET buttons in the

upper right of the screen select the parameter that will

be edited in the lower part of the FADE TIME screen.

When this button is on, you can specify the fade time

(the time over which fader and pan parameters will

reach their new value) for each channel.

In the rows of buttons at the bottom of the

screen, click to turn on the buttons of the

channels for which you want to enable the

Fade function.

By clicking the SET ALL buttons located at the right of

the screen, you can turn on the buttons of all input

channels and all DCA groups, or the buttons of all out-

put channels.

By clicking the CLEAR ALL buttons located at the right

of the screen, you can turn off the buttons of all input

channels and all DCA groups, or the buttons of all out-

put channels.

Move the cursor to the box located immedi-

ately below each button, and turn the [DATA]

encoder to specify the fade time for that chan-

nel. (Alternatively, click the / buttons at

the left and right of the box.)

Hint

If the numerical value is displayed in light blue when you per-

form the above actions, this indicates that an offset time has

been specified for the corresponding channel.

In the same way, specify the fade time for

other channels as well.

If desired, you can easily copy the fade time setting of a

channel to another channel (➥ p.185).

In the upper right of the screen, click the

START OFFSET button to turn it on.

When the START OFFSET button is on, you can spec-

ify an offset time for each channel (the time from when

the scene is recalled until the fader or pan parameter

begins to change).

As you did in steps 4–6, specify an offset time

for each channel.

If you want to enable the Fade function not

only for faders but also for the PAN (BAL-

ANCE) parameters of input channels, set the

INPUT CH PANNING ENABLED/DISABLED but-

ton (located in the upper middle of the

screen) to ENABLED.

The FADING ENABLED/DISABLED button and

INPUT CH PANNING ENABLED/DISABLED button

can be set independently. Use the following two but-

tons to select the input channels to which this will

apply.

• When the ALL INPUT button is on

The Fade function will apply to the pan (balance)

parameter of all input channels.

• When the SAME AS FADING button is on

The Fade function will apply to the pan (balance)

parameters of only the input channels selected in step

When you have finished making settings,

store the scene.

The settings in the FADE TIME screen are saved

independently for each scene. The Fade function will

apply when you recall a scene for which this button

is set to ENABLED. After recall, the fader and pan

(balance) parameter values will begin changing when

the specified Start Offset Time has elapsed, and will

reach their new values over the specified Fade Time.

FADE TIME

FADING ENABLED/

DISABLED button

FADE TIME button

Fade time

10 Scene memory

96 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Using the Tracking Recall function

“Tracking Recall” is a function that adds a specified offset value to each fader or level value when a scene is recalled. Tracking

Recall settings are common to all scenes. For example if the original level of a certain sound source has changed, or if an actor

was replaced by an understudy, this function provides a convenient way to adjust the level of that specific channel for all

scenes.

In the DISPLAY ACCESS section, press the

[SCENE] key several times to access the

TRACKING RECALL screen shown below.

In this screen you can select the channels that will use

the Tracking Recall function, and specify the offset

value for each channel.

In the upper left of the screen, click the

TRACKING RECALL ENABLED/DISABLED but-

ton to make it indicate ENABLED.

When the TRACKING RECALL ENABLED/DIS-

ABLED button is set to ENABLED, the Tracking Recall

function will be enabled for all scenes.

Using the buttons of the DISPLAY SELECT area

in the upper middle of the screen, select the

type of channels for which you want to make

settings.

• If the INPUT button is on

The screen will show the faders of input channels 1–48,

ST IN channels 1–4, FX RTN channels 1–4, DCA

groups 1–8, and STEREO A/B channels.

• If the OUTPUT button is on

The screen will show the faders of MIX channels 1–24,

MATRIX channels 1–8, DCA groups 7/8, and STE-

REO A/B channels.

In the row of buttons above the faders in the

screen, click to turn on the buttons of the

channels for which you want to enable the

Tracking Recall function.

Clicking the SET ALL button located in the upper right

of the screen will turn on the buttons of all channels

and DCA groups.

Clicking the CLEAR ALL button located in the upper

right of the screen will turn off the buttons of all chan-

nels and DCA groups.

To set the offset value for each channel, drag

the fader upward or downward for a channel

whose button you have turned on.

When you turn on the setting for a channel in step 4,

the offset value is set to 0. The offset value can be

adjusted in a range of –15 dB to +15 dB. The current

value is shown in the box immediately below the fader.

In the same way, specify the offset value for

other channels as well.

When you have finished making settings, turn

on the OFFSET LOCK button located in the

upper right of the screen.

When this button is on, the offset values currently

specified for the channels will be fixed; this prevents the

offset values from being unintentionally changed.

When you recall a new scene in this state, the offset val-

ues will be added to the level of each channel when the

scene is loaded. (However, the upper and lower level

limits will not be exceeded.)

Note

Channels that are excluded from Recall operations by the

Recall Safe or Selective Recall functions will not change even

if Tracking Recall is turned on.

TRACKING RECALLTRACKING RECALL

ENABLED/DISABLED button

DISPLAY SELECT area OFFSET LOCK button

Offset value

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 97

Scene memory

Using the Global Paste function

“Global Paste” is a function that lets you copy and paste settings of the desired channel or parameter from the current scene to

scene data in memory (multiple selections are allowed). This is a convenient way in which changes to the current scene can be

applied to scenes that have already been stored.

In the DISPLAY ACCESS section, press the

[SCENE] key several times to access the GLO-

BAL PASTE screen shown below.

In this screen you can select the copy-source channels/

parameters and specify the paste-destination scene

data.

Use the buttons in the PASTE MODE area to

select one of the following as the type of item

you want to paste.

In the CURRENT SCENE area, select the copy-

source channels or parameters.

The contents shown in the CURRENT SCENE area

will depend on what you select in the PASTE MODE

area.

• When PASTE MODE = INPUT

Select input channels in the left area, and select param-

eters in the right area. (For details on the parameters

➥ p.187).

• When PASTE MODE = OUTPUT

Select output channels in the left area, and select

parameters in the right area. (For details on the param-

eters ➥ p.187).

INPUT Input channel parameters

OUTPUT Output channel parameters

DCA, GEQ, EFFECT

DCA level or mute on/off status,

GEQ settings, internal effect settings

GLOBAL PASTEPASTE MODE area

CURRENT SCENE area

DESTINATION SCENE area

PASTE button

10 Scene memory

98 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

• When PASTE MODE = DCA, GEQ, EFFECT

Select DCA groups, GEQ modules, and internal effects.

Hint

In either of these modes, you can click the SET ALL button to

turn on all channels, or click the CLEAR ALL button to turn off

all channels.

In the DESTINATION SCENE area, select the

paste-destination scene(s).

To select a single scene, click the desired line in the

upper half of the list.

To select multiple consecutive scenes, use the upper

half of the list to click the scene number at which you

want to begin pasting, and use the lower half of the list

to click the scene number at which you want to stop

pasting.

The order in which the scenes are listed can be changed

by clicking one of the buttons at the top of the list; the

button (sort by number), SCENE TITLE button

(sort by scene title), or TIME STAMP button (sort by

the date on which the scene was saved).

Click the PASTE button.

The selected items of the current scene will be pasted to

the scene(s) in memory.

Note

• If the parameter settings differ between the copy-source and

paste-destination, exception handling may be applied when

the data is pasted (

➥

p.188).

• Only the parameters selected by PASTE MODE will be

pasted. Note that even if you selected parameters in the

CURRENT SCENE area, they will be excluded from the

paste operation if you switch the PASTE MODE.

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 99

Monitor and Cue

This chapter explains the PM5D’s Monitor and Cue functions.

About the MONITOR and CUE sections

The MONITOR section sends the signal selected as the

monitor source to the MONITOR OUT jacks. You can

select the following signals as the monitor source.

• The input signal from 2TR IN ANALOG jacks 1/2

• The input signal from 2TR IN DIGITAL jacks 1–3

• The output signal of the STEREO A/B channels

• The output signal of the LCR channels

• The output signal of a pre-selected MIX channel 1–24

or MATRIX channel 1–8

Note

If the PM5D is cascade-connected to the DSP5D, the

DSP5D’s cue operations will occur in tandem.

The CUE section sends the cue signal of the channel/group

selected by a panel [CUE] key to the CUE OUT jacks.

Hint

If the CUE INTERRUPTION button is turned on in the MONI-

TOR screen (MON/CUE function), the Cue/Solo signal will

also be sent from the MONITOR OUT jacks when Cue/Solo is

active.

Note

Since the DSP5D does not have monitor functionality, the

keys and knobs of the MONITOR section will always operate

the settings of machine #1 (PM5D).

Similarly, the CUE [LEVEL] knob will always operate the set-

tings of machine #1 (PM5D).

11 Monitor and Cue

DSP5D

PM5D

11 Monitor and Cue

100 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

• MONITOR SELECT

Selects the monitor source.

• MONITOR DELAY

Delays the monitor signal.

• CUE OUT DELAY

Delays the cue signal.

• METER

Switches the signal that is shown in the meter section

or in the display.

• DIM (Dimmer)

Attenuates the monitor/cue signal by a fixed amount.

• OUT ATT. (Output attenuator)

Attenuates/boosts the monitor/cue signal.

• ON (On/off)

Switches the monitor signal on/off.

• PHONES LEVEL

Adjusts the output level of the top panel and front

panel PHONES jacks.

• MONITOR LEVEL

Adjusts the monitor level.

• CUE OUT LEVEL

Adjusts the output level of the cue signal.

Using the Monitor function

A [2TR IN A1] key

B [2TR IN A2] key

These keys select the input signals of 2TR IN ANA-

LOG jacks 1/2 as the monitor source.

C [2TR IN D1] key

D [2TR IN D2] key

E [2TR IN D3] key

These keys select the input signals of 2TR IN DIGITAL

jacks 1–3 as the monitor source.

F [STEREO A] key

G [STEREO B] key

These keys select the output signals of STEREO A/B

channels as the monitor source. By simultaneously

pressing the [STEREO A] key and [STEREO B] key

you can select the LCR channels as the monitor source.

H [DEFINE] key

This key selects the output signal of the pre-selected

MIX channel 1–24 or MATRIX channel 1–8 as the

monitor source. This monitor source selected by this

key can be specified in the MONITOR screen (MON/

CUE function).

Hint

The currently selected source is shown by the lit/dark state of

keys

–

I MONITOR [LEVEL] knob

This knob adjusts the output level of the signal being

output from the MONITOR OUT L/R/C jacks.

J MONITOR [ON] key

This key turns the monitor output on/off.

K MONITOR [PHONES] knob

This analog volume adjusts the output level of the

PHONES jacks.

L [MONO] key

If this key is on, the monitor output L/R channels will

be mixed and output as a monaural signal. The signal

will return to stereo when you turn this key off.

Items in the MONITOR section

J L

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 101

Monitor and Cue

Here we explain how you can use the MONITOR section

to monitor the desired source.

Make sure that your monitor system is con-

nected to the rear panel MONITOR OUT jacks

L/R/C.

If you want to monitor through headphones, make

sure they are connected to the top panel or front panel

PHONES jack.

Note

• Since the DSP5D does not have monitor functionality, the

PM5D’s MONITOR section will always operate the monitor

settings of machine #1 (PM5D).

• MONITOR OUT jack C is a special jack used to monitor the

center channel when LCR mode is active. Note that the

appropriate signal will not be output from MONITOR OUT

jack C unless the LCR channel is selected as the monitor

source and the USE AS CENTER BUS button is turned on

in the MIXER SETUP screen (SYS/W.CLOCK function)

(

➥

p.222).

• Turning on the [CUE] key of even one input channel, output

channel, or DCA group will override the settings of the MON-

ITOR section and cause the Cue signal to be output from

the MONITOR OUT jacks. Make sure that the CUE section

[INPUT]/[DCA]/[OUTPUT] LEDs are not lit.

To specify the channel that will be selected by

the [DEFINE] key, press the DISPLAY ACCESS

section [MON/CUE] key repeatedly to access

the MONITOR screen shown below.

Click a button in the DEFINE area to select the

channel that will be monitored when you

press the [DEFINE] key.

You can assign more than one channel to the

[DEFINE] key. You can choose from the following

sources.

Hint

The MONITOR screen also lets you make settings for monitor

signal delay, insert-out/in, and dimmer (

➥

p.238).

Use the keys of the MONITOR section to select

the monitor source from the following.

Hint

• You can simultaneously select one from 2TR A1–2TR D3 or

DEFINE, and one from STEREO A/STEREO B (including

LCR) (a maximum of two). To select this from the panel,

simultaneously press the two corresponding keys on the

panel.

• The monitor source can also be selected in the MONITOR

screen (MON/CUE function).

Press the MONITOR [ON] key to turn it on.

Hint

A signal is always output from the PHONES jacks regardless

of the on/off state of the MONITOR [ON] key.

Turn the MONITOR [LEVEL] knob to adjust the

monitor level. If you are monitoring through

headphones, turn the PHONES [LEVEL] knob

to adjust the monitor level.

Hint

Monitor level and monitor on/off status can also be operated

from the STEREO/DCA strip section (

➥

p.149).

If you want to monitor the signal in monaural,

turn the MONITOR section’s [MONO] key on.

MIX 1–MIX 24 Output signals of MIX channels 1–24

MATRIX 1–

MATRIX 8

Output signals of MATRIX buses 1–8

Monitoring a signal

MONITOR

DEFINE area

[2TR IN A1]/[2TR IN

A2] keys

The input signal from 2TR IN ANA-

LOG jacks 1/2

[2TR IN D1]/[2TR IN

D2]/[2TR IN D3] keys

The input signal from 2TR IN DIGI-

TAL jacks 1–3

[STEREO A]/[STE-

REO B] keys

The output signal of the STEREO A/

B channels

[STEREO A] key +

[STEREO B] key

The LCR channel output

[DEFINE] key

The signal pre-selected in the MON-

ITOR screen (MON/CUE function)

11 Monitor and Cue

102 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Using the Cue/Solo functions

A [INPUT]/[DCA]/[OUTPUT] LEDs

These LEDs indicate the monitoring status. If even one

[CUE] key is on, the LED of the group to which that

key belongs will light. If a special Cue signal such as

KEY IN CUE or EFFECT CUE is active, all three LEDs

will light.

B [SOLO] key

This selects how monitoring will occur when you use

the [CUE] keys. If this key is on, monitoring will oper-

ate in SOLO mode. If this key is off, monitoring will

operate in CUE mode.

C [LAST CUE] key

This selects the mode of operation when more than

one [CUE] key is on. Turning the key on selects LAST

CUE mode; turning the key off selects MIX CUE

mode. When you switch this mode, Cue will be turned

off for all channels.

D CUE [LEVEL] knob

This adjusts the signal level that is sent from the CUE

OUT jacks.

E [OUTPUT PFL] key

This switches the location from which the signal is sent

to the CUE bus when you turn on the [CUE] key of an

output channel (MIX channel, MATRIX channel, STE-

REO A/B channel). If this key is on, the PFL (pre-

fader) signal will be sent. If this key is off, the POST

ON (immediately after the [ON] key) signal will be

sent.

The PM5D lets you select either SOLO mode or CUE

mode when using the [CUE] key to monitor signals. Use

the [SOLO] key in the CUE section of the panel to switch

the mode.

In CUE mode, holding down the [SOLO] key will switch

to SOLO mode; the [CUE] keys of all channels will go

dark. Conversely in SOLO mode, pressing the [SOLO] key

will immediately switch to CUE mode.

These modes differ as follows.

• CUE mode

The cue signals of channels / DCA groups whose

[CUE] key is on will be sent via the CUE bus and out-

put from the CUE OUT jacks (Cue function). Choose

this method when you want to monitor a signal with-

out affecting other channels. When the PM5D is in the

default state, the cue signal can also be monitored from

the MONITOR OUT jacks.

• SOLO mode

Only the channels / DCA groups whose [CUE] key is

on will be output from the MIX/MATRIX/STEREO

buses, and other channels / DCA groups will be muted

(Solo function). The MONITOR OUT jacks also will

output only the signal from these same channels / DCA

groups.

Note

• If an input channel is soloed, the on/off setting of the output

channels will remain unchanged; only the signal of the corre-

sponding input channel will be sent to the buses. If an output

channel is soloed, the on/off setting of the input channels will

remain unchanged; the signal will be sent only to the corre-

sponding bus.

• If a DCA group is soloed, only the signals of input channels

belonging to that DCA group will be output to the corre-

sponding buses. However if output channels are assigned to

DCA groups 7/8, signals will be sent only to buses belong-

ing to that DCA group.

Hint

If desired, you can exclude specific channels from Solo opera-

tions (

➥

p.241).

Items in the CUE section

About CUE mode and SOLO mode

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 103

Monitor and Cue

The PM5D’s cue and solo signals can be categorized into

the following four groups.

• INPUT CUE group

The cue/solo signals of input channels make up this

group. This group becomes active when a [CUE] key of

an input channel, ST IN channel, or FX RTN channel

is pressed to turn it on.

• DCA CUE group

The cue/solo signals of DCA groups make up this

group. This group becomes active when a [CUE] key in

the DCA strip is pressed to turn it on.

• OUTPUT CUE group

The cue/solo signals of output channels make up this

group. This group becomes active when a [CUE] key of

a MIX channel, MATRIX channel, or STEREO A/B

channel is pressed to turn it on.

• Other CUE group

This group consists of the cue/solo signals operated by

the CUE buttons in the display. This group becomes

active when you click to turn on a CUE button in the

EFFECT PARAM screen (EFFECT function) or GATE

PARAM screen (INPUT GATE/COMP function).

It is not possible to simultaneously turn on Cue

between different groups. Normally, the group to

which the most recently pressed [CUE] key (CUE but-

ton) belongs will take priority, and the [CUE] keys of

the previously selected group will be defeated.

However if you have switched cue/solo signal groups in

a certain order, the [CUE] key status of the previously

selected group will be recovered when you turn off the

[CUE] key (CUE button) to defeat the current cue/solo

selection.

The [CUE] key status can be recovered for the follow-

ing combinations of groups.

• OUTPUT CUE group → DCA CUE group

• OUTPUT CUE group → INPUT CUE group

• DCA CUE group → INPUT CUE group

• INPUT CUE / OUTPUT CUE / DCA CUE group →

Other CUE group

For example if you switch groups in the order of OUT-

PUT CUE group → DCA CUE group → INPUT CUE

group → Other CUE group, you can then successively

defeat the [CUE] keys (CUE buttons) to recover the

[CUE] key status of the previously selected group.

Cue and Solo groups

Input channel [CUE] key

ST IN/FX RTN channel

[CUE] key

DCA strip [CUE] key

MIX/MATRIX channel

[CUE] key

STEREO A/B channel

[CUE] key

CUE button in the display

11 Monitor and Cue

104 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

This section explains how you can use the [CUE] key of a

desired channel or DCA group to monitor the Cue signal.

Note

If you want the cue/solo signal to be output from the MONI-

TOR OUT jacks as well, access the MONITOR screen (MON/

CUE function) and make sure that the CUE INTERRUPTION

ON/OFF button is on before you continue with the following

procedure (

➥

p.239).

Using the [OUTPUT PFL] key of the CUE sec-

tion, select one of the following as the output

position of the signal sent to the CUE bus

when an output channel [CUE] key is pressed.

• PFL ([OUTPUT PFL] key is on)

The signal from immediately before the fader will be

sent to the CUE bus.

• POST ON ([OUTPUT PFL] key is off)

The signal from immediately after the [ON] key will be

sent to the CUE bus.

Hint

The above setting can also be made in the CUE screen

(MON/CUE function) (

➥

p.240). In this screen you can also

specify the output position of the signal sent from input chan-

nels and DCA groups to the CUE bus.

In the CUE section, use the [LAST CUE] key to

specify the mode of operation when more

than one [CUE] key within the same group is

turned on.

• LAST CUE mode ([LAST CUE] key is on)

Only the channel/group whose [CUE] key was last

turned on will be monitored.

• MIX CUE mode ([LAST CUE] key is off)

Channels/groups within the same group whose [CUE]

key is turned on will be monitored.

Note

• [CUE] keys belonging to different groups cannot be turned

on simultaneously. The group to which the last-pressed

[CUE] key belongs will be turned on, allowing the signals of

that group to be monitored.

• If you press the [CUE] key of a paired channel, both chan-

nels will be turned on.

Make sure that the [SOLO] key in the CUE sec-

tion is turned off.

Press the [CUE] key of a desired channel or

DCA group to turn it on.

The cue signal of the corresponding channel will be

output from the CUE OUT jacks and the MONITOR

OUT jacks.

To defeat Cue, press the currently-on [CUE]

key once again.

Hint

If you press the [LAST CUE] key to switch from LAST CUE

mode to MIX CUE mode (or vice versa), all previously-

enabled Cue (Solo) signals will be defeated. For example if

you have turned on multiple [CUE] keys in MIX CUE mode,

you can quickly turn them all off by pressing the [LAST CUE]

key twice.

This section explains how to use the Solo function.

Use the [LAST CUE] key of the CUE section to

specify the mode of operation when a [CUE]

key is turned on (LAST CUE mode or MIX CUE

mode).

In the CUE section, press and hold the [SOLO]

key.

When you press and hold the [SOLO] key, the key LED

will blink and SOLO mode will be enabled. In SOLO

mode, only the signal of the channel or DCA group

whose [CUE] key is turned on will be sent to the MIX,

MATRIX, and STEREO buses. The same signal can

also be monitored from the MONITOR OUT jacks and

CUE OUT jacks.

Hint

If desired, you can exclude specific channels or groups from

Solo operations (for details, refer to

➥

p.241).

Turn on the [CUE] key of a desired channel or

DCA group.

Only the corresponding channel or DCA group will be

output to the buses and output jacks; the remaining

channels and DCA groups will be muted. The same sig-

nal will also be output from the CUE OUT jacks and

the MONITOR OUT jacks.

Note

If you turn on the [CUE] key of an output channel, the signal

will be sent only to the corresponding bus.

To defeat Solo, press the [SOLO] key.

If you press the [SOLO] key while in SOLO mode, you

will immediately return to CUE mode.

Hint

Normally, the Cue/Solo functions can be operated indepen-

dently of scene memories.

Using the Cue function

MONITOR CUE INTERRUPTION

Using the Solo function

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 105

Talkback and Oscillator

This chapter explains how to use talkback and oscillator.

About the TALKBACK/OSCILLATOR sections

The TALKBACK and OSCILLATOR sections let you send the signal of a mic connected to the TALKBACK jack or the signal

of a test oscillator to the desired output jacks.

Signal flow in the TALKBACK/OSCILLATOR sections is as follows.

A TALKBACK jack

This is a balanced XLR-3-31 jack to which a talkback

mic can be connected. You can make settings in the

display to supply +48V phantom power to this jack.

B TALKBACK [LEVEL] knob

This adjusts the input level of the mic connected to the

TALKBACK jack.

C TALKBACK [ON] key

This switches the talkback signal on/off. When you

press and hold the key, talkback will be on as long as

you hold down the key. If you press and immediately

release the key, talkback will remain on until you press

the key once again.

However if the NEVER LATCH button is turned on in

the TALKBACK screen, talkback will be on only while

you hold down the key, and will turn off when you

release the key; i.e., talkback will not “latch” even if you

press and immediately release the key.

D OSCILLATOR [ON] key

This is an on/off switch for the signal sent from the

internal oscillator to the specified bus(es).

Note

If the OSCILLATOR [ON] key is off, and a screen other than

the OSCILLATOR screen (TALKBACK function) is displayed,

pressing this key will only display the OSCILLATOR screen;

the key will not turn on. When you press the key once again, it

will turn on. If the key is on, pressing it once again will turn it

off regardless of the screen that is displayed.

12 Talkback and Oscillator

PM5D

DSP5D

Items in the TALKBACK/OSCILLATOR

sections

12 Talkback and Oscillator

106 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Using talkback

Here’s how the talkback signal input from the TALKBACK jack can be sent to the desired bus(es).

Repeatedly press the [MON/CUE] key of the

DISPLAY ACCESS section until the TALKBACK

screen appears.

Note

If you select the DSP5D when cascade-connected to the

DSP5D, the TALKBACK IN field will not be displayed.

Turn the TALKBACK [LEVEL] knob to adjust the

input sensitivity of the talkback mic.

The meter in the TALKBACK IN area indicates the

input level of the mic connected to the TALKBACK

jack. If you want phantom power (+48V) to be sup-

plied to the TALKBACK jack, turn on the +48V button

located in the TALKBACK IN area.

Hint

The INPUT TO TALKBACK area also lets you use any INPUT

jack 1–48 as a supplementary input for talkback.

Click a button in the BUS ASSIGN area to spec-

ify the bus(es) to which the talkback signal will

be sent (multiple selections are allowed).

These buttons correspond to the following buses.

Hint

If desired, the talkback signal can also be output directly from

an output channel of slot 1–4 or from 2TR OUT DIGITAL jacks

1–3. To do so, click the PATCH button in the TALKBACK

OUT area to access the OUTPUT PATCH screen, and patch

talkback to the jack you want to use for direct output.

To enable talkback, press the TALKBACK [ON]

key in the TALKBACK section of the panel to

turn it on.

The TALKBACK [ON] key can operate in either of the

following two ways, depending on the setting of the

NEVER LATCH button in the TALKBACK area.

• If the NEVER LATCH button is off

Talkback will be switched on/off each time you press

the TALKBACK [ON] key (Latched). However if you

press and hold down the TALKBACK [ON] key, talk-

back will remain on only while you continue holding

down the key, and will turn off when you release the

key (Unlatched).

• If the NEVER LATCH button is on

Talkback will be on only while you continue holding

down the TALKBACK [ON] key, and will turn off

when you release the key (Unlatched).

Hint

• The TALKBACK [ON] key of the panel and the TALKBACK

ON/OFF button in the screen are linked. The setting of the

NEVER LATCH button also affects both of these. However if

the NEVER LATCH button is off, holding down the on-

screen TALKBACK ON/OFF button will cause Latched

operation.

• When talkback is on, you can use the talkback dimmer to

lower the monitor levels other than talkback (

➥

p.239).

• You can also assign the talkback function to a user-defined

key (

➥

p.208).

MIX 1–24 buttons MIX buses 1–24

MATRIX 1–8 buttons MATRIX buses 1–8

STEREO AL/R STEREO A bus L/R channels

STEREO BL/R STEREO B bus L/R channels

TALKBACK BUS ASSIGN areaTALKBACK area

INPUT TO TALKBACK area TALKBACK OUT area

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 107

Talkback and Oscillator

Using the oscillator

The PM5D contains a test oscillator. By outputting the oscillator signal to the desired bus you can check the operation of con-

nected devices or test the acoustics of a hall.

Repeatedly press the [MON/CUE] key of the

DISPLAY ACCESS section until the OSCILLA-

TOR screen appears.

Click a button in the OSC MODE section to

select the type of oscillator to output, from the

following choices.

Use the knobs and buttons of the PARAME-

TERS area to adjust the oscillator parameters.

The parameters that can be adjusted will depend on the

type of oscillator you selected in step 2. For example if

you selected SINE WAVE 1CH as the oscillator type,

the PARAMETERS area will contain the following

parameters.

Click a button in the BUS ASSIGN area to

select the oscillator signal output destination

from the following choices.

Hint

• If you selected SINE WAVE 2CH as the oscillator type, the

L-channel signal of the oscillator will be sent to odd-num-

bered buses (or the L output jack) and the R-channel signal

of the oscillator will be sent to even-numbered buses (or the

R output jack).

• You can use the OSC OUT area to directly output the oscil-

lator signal from an output jack or slot (

➥

p.237).

Press the OSCILLATOR [ON] key of the OSCIL-

LATOR section.

The oscillator signal will be sent to the bus you selected

in step 4. When you press the key again, the oscillator

will turn off.

Hint

The OSCILLATOR [ON] key of the panel and the OSC ON/

OFF button in the screen are linked.

Note

If the OSCILLATOR [ON] key is off, and a screen other than

the OSCILLATOR screen (TALKBACK function) is displayed,

pressing this key will only display the OSCILLATOR screen;

the key will not turn on. When you press the key once again, it

will turn on.

SINE WAVE 1CH button Sine wave x 1 channel

SINE WAVE 2CH button Sine wave x 2 channels

PINK NOISE button Pink noise

BURST NOISE button

Burst noise (repeated output

of pink noise)

OSCILLATOR BUS ASSIGN areaOSC MODE area

PARAMETERS areaOSC OUT area

FREQ knob

Adjusts the frequency of

the sine wave output from

the oscillator. You can

choose preset frequen-

cies by clicking the but-

tons below.

LEVEL knob

Adjusts the output level of

the oscillator.

MIX 1–24 MIX buses 1–24

MATRIX 1–8 MATRIX buses 1–8

STEREO AL/R STEREO A bus L/R channels

STEREO BL/R STEREO B bus L/R channels

13 Meters

108 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

This chapter explains meter-related operations.

Items in the meter section

The meter section shows the input levels of the input channels and the output levels of the output channels.

A INPUT/MIX meters

Depending on the key you press, these meters indicate

the input levels of input channels 1–24 or 25–48, or the

output levels of MIX channels 1–24.

B [CH 1-24/ST IN/FX RTN] key

When this key is on, the INPUT/MIX meters indicate

the input levels of input channels 1–24 and the ST IN/

FX RTN/MATRIX meters indicate the output level of

ST IN channels (or FX RTN channels, depending on

the FOLLOW INPUT LAYER setting) 1–4.

C [CH 25-48/FX RTN/ST IN] key

When this key is on, the INPUT/MIX meters indicate

the input levels of input channels 25–48 and the ST IN/

FX RTN/MATRIX meters indicate the output level of

FX RTN channels (or ST IN channels, depending on

the FOLLOW INPUT LAYER setting) 1–4.

D [MIX/MASTER] key

When this key is on, the INPUT/MIX meters indicate

the output levels of MIX channels 1–24 and the ST IN/

FX RTN/MATRIX meters indicate the output levels of

MATRIX channels 1–8.

E [PEAK HOLD] key

Switches the peak hold function on/off for the meter

display.

F ST IN/FX RTN/MATRIX meters

Depending on the key you press, these meters indicate

the output levels of ST IN channels 1–4 or MATRIX

channels 1–8.

G MASTER meters

These meters always indicate the output levels of the

STEREO A/B channels and CUE bus.

Switching the meter display

You can use the keys of the meter section to specify the

channels whose levels will be shown in the INPUT/MIX

meters and ST IN/MATRIX meters. The following chan-

nels correspond to each key.

Hint

• The type of channels shown in the meter section is also

shown in the METER SECTION area in the upper right of

the display.

• The MASTER meters always indicate the output levels of

the STEREO A/B channels and CUE bus.

13 Meters

MIX

PEAK

HOLD

CH 1 -24

OVER

-3

-6

-9

-12

-15

-18

-24

-30

-40

-50

-60

OVER

-3

-6

-9

-12

-15

-18

-24

-30

-40

-50

-60

2322212019181716151413121110987654321

ST IN/

/ST IN

MATRIX

OVER

-3

-6

-9

-12

-15

-18

-24

-30

-40

-50

-60

OVER

-3

-6

-9

-12

-15

-18

-24

-30

-40

-50

-60

OVER

-3

-6

-9

-12

-15

-18

-24

-30

-40

-50

-60

OVER

-3

-6

-9

-12

-15

-18

-24

-30

-40

-50

-60

STEREO

B CUE

LR LR LR

1L 1R 2L 2R 3L 3R 4L 4R

MATRIX

ST IN / /

1 2 3 4 5 6 7 8

32 54

6 7

Key

[INPUT/MIX]

meters

[ST IN/MATRIX]

meters

[CH 1-24/ST IN/FX

RTN] key

Input channels

1–24

ST channels

(or FX RTN channels)

1–4

[CH 25-48/FX RTN/

ST IN] key

Input channels

25–48

FX RTN channels

(or ST IN channels)

1–4

[MIX/MATRIX] key

MIX channels

1–24

MATRIX channels

1–8

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 109

Meters

Switching the metering point

The metering point for the level meters (i.e., the position at which the level is detected) can be specified separately for input

channels and output channels.

Here’s how to specify the metering point for input chan-

nels and ST IN/FX RTN channels.

In the DISPLAY ACCESS section, repeatedly

press the [METER] key to access the INPUT

METER screen.

Click the / buttons at the left and right of

the METERING POINT box to choose one of

the following metering points.

Here’s how to specify the metering point for output chan-

nels, MONITOR channels, and the CUE bus.

Hint

The metering point setting for the CUE bus is independent

from the other output channels.

In the DISPLAY ACCESS section, repeatedly

press the [METER] key to access the OUTPUT

METER screen.

To specify the metering point for output chan-

nels and MONITOR channels, click the /

buttons at the left and right of the METERING

POINT box to choose one of the following.

To specify the metering point for the CUE bus,

click the / buttons at the left and right of

the CUE METERING POINT box to choose one

of the following.

PRE ATT Immediately before the attenuator

PRE GATE Immediately before the internal gate

PRE FADER Immediately before the fader

POST FADER Immediately after the fader

POST ON Immediately after the [ON] key

Specifying the metering point for

input channels

INPUT METER METERING POINT box

PRE EQ Immediately before the EQ

PRE FADER Immediately before the fader

POST FADER Immediately after the fader

POST ON Immediately after the [ON] key

POST DELAY Immediately after the internal delay

PRE DELAY Immediately before the internal delay

POST DELAY Immediately after the internal delay

Specifying the metering point for

output channels

OUTPUT METER

METERING POINT

box

CUE METERING POINT

box

13 Meters

110 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Viewing the gain reduction of the internal gates and compres-

sors

The amount of gain reduction produced by the gates/compressors of the input channels and the amount of gain reduction

produced by the compressors of the output channels can be viewed in the display.

Here’s how to view the amount of gain reduction pro-

duced by the gates/compressors provided on input

channels 1–48 and ST IN channels 1–4.

In the DISPLAY ACCESS section, repeatedly

press the [METER] key to access the INPUT GR

screen.

Click the GATE button or COMP button to

select the parameter that will be displayed.

For an explanation of the items shown in the screen,

refer to the explanation of the INPUT GR screen

(➥ p.233) in the Reference section.

To view the amount of gain reduction produced by the

compressors provided on the output channels, repeatedly

press the [METER] key of the DISPLAY ACCESS section

to access the OUTPUT GR screen.

For an explanation of the items shown in the screen, refer

to the explanation of the OUTPUT GR screen (➥ p.234)

in the Reference section.

Viewing the gain reduction for input

channels

INPUT GR

GATE button COMP button

Viewing the gain reduction for out-

put channels

OUTPUT GR

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 111

Effects

This chapter explains the functionality and operation of the PM5D’s internal effects.

About the internal effects

The PM5D contains eight internal effect modules. For each module, you can choose one of 55 effect types for the module to

use.

Note

The eight effects can also be used as GEQ modules

(

➥

p.119).

To use an internal effect via send/return, assign the output

of a MIX channel to the input of the effect, and assign the

output of the effect to an input channel. In this case, the

corresponding MIX bus is used as an effect send AUX bus,

and the input channel is used as an effect return channel.

By default, the L/R outputs of effects 1–4 are assigned to L/

R of FX RTN channels 1–4.

Alternatively, you can insert an internal effect into a chan-

nel by assigning the input/output of the internal effect to

the insert-out/insert-in of the desired channel.

The PM5D’s effect types fall into two categories; “stereo

effect types” which process the L/R channel input signals

independently, and “mix effect types” which mix the two

channels before processing the signal.

If signals are assigned to both the L and R inputs of an

effect, the way in which the L/R channels are processed will

depend on whether a Stereo effect type or a Mix effect type

is selected, as follows.

If a signal is assigned to only one input of an effect, it will

be processed as mono-in/stereo-out regardless of whether a

Stereo effect type or Mix effect type is selected.

14 Effects

OUTPUT PATCH

INPUT PATCH

EFFECT 1

EFFECT 2

EFFECT 3

EFFECT 8

Input channel 1–48

inputs

ST IN channel 1–4

inputs

FX RTN channel

1–4 inputs

MIX chan-

nel 1–24

outputs

EFFECT

Insert-out of the

desired channel

Insert-in of the

desired channel

INPUT L EFFECT L L RETURN

INPUT R EFFECT R R RETURN

INPUT L L RETURN

INPUT R

EFFECT

R RETURN

• Stereo effect types

• Mix effect types

L RETURN

EFFECT

R RETURN

INPUT L

or R

14 Effects

112 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Using an internal effect via a MIX bus

This section explains how to use an internal effect via a

MIX bus. As an example, we will choose effect 1 for our

operations, assign MIX bus 1 to the effect input, and assign

the effect output to FX RTN channels 1/2.

In the DISPLAY ACCESS section, repeatedly

press the INPUT [PAN/ROUTING] key to access

the CH to MIX screen.

Make sure that the MIX bus 1 type selection

box indicates “VARI.”

If the box indicates “FIXED,” click the / buttons

at left and right to change the indication to “VARI”;

then press the [ENTER] key (or click inside the box) to

finalize the change.

This box selects the operation of the MIX bus (VARI or

FIXED). If VARI is selected, the bus send levels will be

adjustable.

Hint

The VARI/FIXED selection is made for two adjacent odd-num-

bered/even-numbered MIX buses. If the effect input is stereo,

it is convenient to pair these two MIX buses.

In the DISPLAY ACCESS section, repeatedly

press the [EFFECT] key to access the EFFECT

PARAM screen.

Make sure that the box in the upper left of the

screen indicates EFFECT 1.

This box lets you select the effect module that you want

to control. If a different effect module is selected, click

the / buttons at left and right to select EFFECT 1.

Hint

You can access the EFFECT ASSIGN screen (EFFECT func-

tion) to see all eight effect modules at once while you assign

signal routes to the effect inputs and outputs, or operate

Bypass and Cue (

➥

p.168).

In the INPUT area, click the / buttons at

the left and right of the L CH box to select

MIX 1 (MIX channel 1); then press the [ENTER]

key (or click within the box).

This assigns the output of MIX channel 1 to the L input

of the effect.

If a signal route is already assigned, a window will

appear when you press the [ENTER] key, asking you to

confirm the assignment. Click the OK button to con-

firm the assignment.

If you want to use the effect input in stereo, assign MIX

channel 2 to the R CH box in the same way.

In the OUTPUT area, make sure that the L CH

box indicates FX RTN1L and the R CH box indi-

cates FX RTN1R.

The L CH/R CH boxes in the OUTPUT area select the

input channels that are assigned to the L/R outputs of

the effect.

By default, the L/R outputs of effect 1 are assigned to

FX RTN channel 1 (L/R). If different channels are

selected, use the / buttons at the left and right of

the boxes to select FX RTN1L and FX RTN1R

respectively.

Set the MIX BALANCE knob to about 100.

The MIX BALANCE knob adjusts the balance between

the original sound and effect sound included in the

output signal from the effect. If this knob is at the 100

(%) position, only the effect sound will be output.

In the ENCODER MODE section, press the MIX

SEND SELECT [1] key to make the encoder

mode indicator show “1”.

In this state you can use the input channel encoders to

adjust the send level from each channel to MIX bus 1.

Turn the encoders of the INPUT channel strip

and ST IN channel strip to adjust the send

level of the signal sent from each channel to

MIX bus 1.

Don’t raise the encoder of the FX RTN channel you are using

as the effect return. Doing so will send the output of the effect

back to the input, possibly causing oscillation.

Hint

• The send position of the signals sent from input channels to

the MIX bus can be specified for each channel (

➥

p.51).

• As an alternate way to adjust the send level, you can turn on

the [MIX SEND] key of the MIX section, then use a [SEL]

key to select an input channel and turn the corresponding

MIX encoder (

➥

p.51).

CH to MIX Type selection box

EFFECT PARAM

OUTPUT area

INPUT area MIX BALANCE knob

The effect module you are using

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 113

Effects

In the MIX section, press the [MIX MASTER]

key to turn it on (LED lit).

When the [MIX MASTER] key is on, you can use the

controls of the MIX section to control MIX channels

1–24.

Press the MIX channel 1 MIX [ON] key to

turn it on. Use the MIX encoder of that MIX

channel to adjust the master send level of

the signal sent to the effect.

In the FX RTN channel strip, press the FX

RTN channel 1 [ON] key to turn it on.

Use the FX RTN channel 1 fader to adjust the

effect return level.

Hint

The input/output levels of the effect can be viewed in the

meters shown in the EFFECT PARAM screen or EFFECT

ASSIGN screen.

Inserting an internal effect into a channel

You can insert an internal effect into a channel by assigning the input/output of the internal effect to the insert-out/insert-in of

the desired channel. As an example, here’s how to insert an effect into an input channel.

In the DISPLAY ACCESS section, repeatedly

press the [EFFECT] key to access the EFFECT

PARAM screen.

To select the effect module you want to use,

click the / buttons at the left and right of

the box in the upper left of the screen.

In the INPUT area, use the / buttons at

the left and right of the L CH box to select the

insert-out of the channel into which you want

to insert the effect, and press the [ENTER] key.

(If a signal route has already been assigned, a

window will ask you to confirm the assign-

ment change.)

If you are inserting the effect into a stereo channel (or

two paired channels), use the R CH box to assign the

insert-out for the other channel in the same way.

In the OUTPUT area, use the / buttons at

the left and right of the L CH box to select the

insert-in assigned to the L output of the effect.

If you are inserting the effect into a stereo channel (or

two paired channels), use the R CH box to assign the

insert-in for the other channel in the same way.

In the DISPLAY ACCESS section, repeatedly

press the INPUT [PATCH] key to access the

INSERT/DIRECT OUT POINT screen.

Turn on the INSERT ON/OFF button for the

channel into which you inserted the effect.

This enables the effect insertion for the corresponding

channel.

Use the buttons of the INSERT I/O area to

specify the insert-out/in point.

Hint

For details on the INSERT I/O area, refer to INSERT/DIRECT

OUT POINT screen (

➥

p.281) in the Reference section.

Turn on the [ON] key for the channel into

which you inserted the effect, and use the

fader to adjust the input level.

Access the EFFECT PARAM screen, and drag

the MIX BALANCE knob to adjust the balance

of the effect sound and original sound.

The input/output levels of the effect can be viewed in

the meters shown in the EFFECT PARAM screen or

EFFECT ASSIGN screen.

EFFECT PARAM

OUTPUT area

INPUT area MIX BALANCE knob

The effect module you are using

INSERT I/O area INSERT/DIRECT OUT POINT

INSERT ON/OFF button

14 Effects

114 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Basic operations in the effect screen

This section explains how to store or recall effect library data, and how to edit effect parameters.

Note

Data created by versions earlier than PM5D V2.0 can be

loaded into the PM5D V2.0 or the DSP5D. However, you must

move library number 55 to number 56 or later before loading.

On PM5D version 2.0 or later, library number 55 will be

deleted.

Here’s how to recall existing settings from the effect library.

In the DISPLAY ACCESS section, repeatedly

press the [EFFECT] key to access the EFFECT

PARAM screen.

Note

You cannot change the currently selected effect type in the

EFFECT PARAM screen. To change the effect type, you must

recall (load) a library item that uses the desired effect type.

Click the / buttons at the left and right of

the box in the left side of the screen to select

the effect module you want to use, and then

click the LIBRARY button.

The EFFECT LIBRARY screen will appear, allowing

you to recall or store settings in the effect library.

Hint

You can also access this screen by repeatedly pressing the

[EFFECT] key. The effect module you are controlling can also

be selected in this screen.

In the library list at the right of the screen,

click to select the library item you want to

recall

When you click a library item in the library list, that

line will be highlighted and move to the center of the

list. The effect type of the currently selected library item

will be shown above the library list.

Click the RECALL button.

The selected library item will be loaded into the effect

module you chose.

Hint

You can click the EDIT button in the upper right of the screen

to access the EFFECT PARAM screen for the currently

selected effect.

Recalling settings from the effect

library

EFFECT PARAM

The effect module you are controlling

LIBRARY button

EFFECT LIBRARY RECALL button

Library listCurrent effect type

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 115

Effects

Here’s how to edit the parameters of an internal effect.

In the DISPLAY ACCESS section, repeatedly

press the [EFFECT] key to access the EFFECT

PARAM screen.

The lower part of the screen will show knobs and but-

tons for editing the parameters of the currently selected

effect. The content of the parameters will depend on

the type of the currently selected effect.

Use the box in the upper left of the screen to

select the effect module you want to control.

Use the knobs and buttons in the lower part of

the screen to edit the effect parameters.

For details on the effect parameters, refer to the Appen-

dices at the end of this manual.

Hint

The parameter settings for internal effect modules 1–8 are

saved in the scene. The settings of individual effects can also

be stored in the effect library independently of scene memory.

Here’s how to store effect parameter settings in the effect

library.

In the DISPLAY ACCESS section, repeatedly

press the [EFFECT] key to access the EFFECT

PARAM screen.

Use the box in the upper left of the screen to

select the effect module whose settings you

want to store, and click the LIBRARY button.

The EFFECT LIBRARY screen will appear, allowing

you to recall or store settings in the effect library.

In the library list, choose the store-destination

number and click that line.

Note

Library items for which an “R” (read-only) appears in the right

column of the list are factory preset library items. These num-

bers cannot be overwritten.

Editing the effect parameters

EFFECT PARAM

The effect module you are controlling

Effect parameters

Storing settings in the effect library

EFFECT PARAM

The effect module whose data you want to store

LIBRARY button

EFFECT LIBRARY

“R” (read-only)

14 Effects

116 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Click the STORE button.

The EFFECT LIBRARY STORE window will appear,

allowing you to name the library item you are saving.

Use the character palette to assign a name to

the library item.

For details on using the character palette, refer to p.30.

Click the STORE button.

A window will ask you to confirm the Store operation.

To execute the Store operation, click the OK

button.

The data will be stored, and you will return to the pre-

vious screen.

If you click the CANCEL button instead of the OK but-

ton, the Store operation will be aborted and you will

return to the previous screen.

Using the Tap Tempo function

This section explains how to use the Tap Tempo function. “Tap tempo” is a function that lets you specify the delay time of a

delay effect or the modulation speed of a modulation effect by striking a key at the desired interval.

From the effect library, recall a library item

whose effect type uses a TEMPO parameter

(e.g., Delay+ER., Echo, Chorus).

TEMPO is a parameter that specifies a time-related

effect parameter (the DELAY parameter of Delay+ER.

or Echo, or the FREQ. parameter of Chorus, etc.) in

terms of a BPM value or a manual setting. The TEMPO

parameter is included in delay-type effects or modula-

tion-type effects, and is shown in the lower left of the

EFFECT PARAM screen.

Hint

For details on the parameters of each effect type, refer to the

Appendices at the end of this manual (

➥

p.325).

In the DISPLAY ACCESS section, repeatedly

press the [EFFECT] key to access the EFFECT

PARAM screen.

The following illustration shows the screen when the

“Delay

→ER.” effect type is selected.

Move the cursor to the TAP TEMPO button,

and repeatedly press the [ENTER] key at the

desired tempo. (Alternatively, repeatedly click

the TAP TEMPO button.)

The average interval (BPM) at which you press the key

will be calculated, and that value will be input for the

TEMPO parameter.

Hint

• The Tap Tempo function is valid only for the currently dis-

played internal effect. However, it is ignored if the selected

effect type does not include a TEMPO parameter.

• If the average value is outside the range of 20–300 BPM, it

will be ignored.

• If desired, an external switch connected to the GPI connec-

tor can be used to operate the Tap Tempo function of the

current page (

➥

p.133).

EFFECT PARAM

TAP TEMPO button

ab c

First tap Second tap Third tap Fourth tap

The average interval will be input

(the average of a, b, and c)

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 117

Effects

Using the Freeze effect

Here’s how to use the “FREEZE” effect type, which provides the functionality of a simple sampler. When this effect type is

selected, you can perform operations in the screen to record (sample) and play back a sound.

In the EFFECT LIBRARY screen, recall a library

item that uses the FREEZE effect type.

In the DISPLAY ACCESS section, repeatedly

press the [EFFECT] key to access the EFFECT

PARAM screen.

If the FREEZE effect type is selected, the lower left of

the EFFECT PARAM screen will show a REC button, a

PLAY button, and a progress bar.

To begin recording (sampling), click the REC

button and then click the PLAY button.

The signal being input to the effect will be recorded.

The progress bar shows the current recording location.

When a fixed time has elapsed, the buttons will auto-

matically turn off.

Hint

You can adjust the parameters in the screen to make detailed

settings for recording time, the way in which recording will

begin, and the way in which the sample will play back. For

more about the parameters, refer to the Appendices at the

end of this manual (

➥

p.332).

To play back the recorded sample, click the

PLAY button.

Note

Once you stop, the sampled content will be erased.

EFFECT PARAM

Progress bar

PLAY button

REC button

15 Graphic EQ and Parametric EQ

118 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

The PM5D provides twelve units of 31-band graphic EQ or 8-band parametric EQ (expandable to a

maximum of twenty units). This chapter explains how to use the graphic EQ and parametric EQ.

Patching the GEQ modules

The GEQ module built into the PM5D can be inserted into the insert-out/in of the desired channel. As an example, here’s how

to insert GEQ module into the STEREO A channel.

In the DISPLAY ACCESS section, repeatedly

press the [GEQ] key to access the GEQ PARAM

screen.

In this screen you can select a GEQ module, specify the

channel into which it will be inserted, and edit its

parameters.

Click the / buttons at the left and right of

the MODULE box in the upper left of the

screen to select the GEQ module you want to

operate.

Click the GEQ/PEQ button located in the

upper middle of the screen, to switch between

31-band graphic EQ and 8-band parametric

EQ.

Click the / buttons at the left and right of

the INSERT box to select ST AL [INS] (STEREO

A L channel insert-in/out) as the channel into

which the GEQ module will be inserted, and

press the [ENTER] key (or click within the box).

You can choose one of the following insert

destinations.

If an insert destination is already assigned, a window

will appear when you click within the box, asking you

to confirm the change. Click the OK button to execute.

In the upper left of the screen, click the /

buttons at the left and right of the MODULE

box to select another GEQ module, and assign

it to ST AR [INS] (STEREO A R channel insert-

in) in the same way.

Click the GEQ ON/OFF button to turn it on.

Note

When you insert a GEQ module, the insert-in for the channel

will be enabled automatically.

In the DISPLAY ACCESS section, repeatedly

press the OUTPUT [PATCH] key to access the

INSERT POINT screen.

If desired, change the insert point for the STE-

REO A channel into which you inserted the

GEQ module.

When you insert a GEQ module, the insert-in point for

that channel will be enabled automatically.

Note

• If you inserted a GEQ module into an input channel, repeat-

edly press the INPUT [PATCH] key to access the INSERT/

DIRECT OUT POINT screen (INPUT PATCH function), and

edit the settings in the same way.

• You can also insert a GEQ module into the desired chan-

nel’s insert-in/out by using the INSERT PATCH screen

(INPUT PATCH function and OUTPUT PATCH function).

15 Graphic EQ and Parametric EQ

INS CH 1–INS CH 48 Input channel 1–48 insert in/out

INS STIN1L–INS

STIN4R

ST IN channel 1–4 (L/R) insert in/

out

INS MIX 1–INS MIX 24 MIX channel 1–24 insert in/out

INS MTRX1–INS

MTRX8

MATRIX channel 1–8 insert in/out

INS ST AL/INS ST AR

STEREO A channel (L/R) insert

in/out

INS ST BL–INS ST BR STEREO B channel insert in/out

MODULE box GEQ/PEQ button

GEQ PARAM

INSERT box

INS MON L–INS MON C

(PM5D only)

MONITOR channel (L/R/C) insert

in/out

INSERT POINT

ON/OFF button Insert point

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 119

Graphic EQ and Parametric

Expanding the GEQ modules

The GEQ modules provided by the PM5D can be expanded to a maximum of 20 modules by re-purposing the eight internal

effects.

In the DISPLAY ACCESS section, repeatedly

press the [GEQ] key to access the GEQ ASSIGN

screen.

In this screen, you can view the overall settings and

input/output levels for the GEQ modules, specify the

signal routing, and turn the module on/off.

In the DSP CONFIGURATION box located in

the lower right of the screen, click the left/

right / buttons to change the number of

internal effects and GEQ modules that will be

assigned.

If twelve GEQ modules are used, there will be eight

internal effects. If twenty GEQ modules are used, no

internal effects will be available.

Basic graphic EQ operations

There are two ways to control a graphic EQ; using the virtual faders and buttons within the display, or using the DCA faders of

the panel.

Here’s how to control the desired graphic EQ by using the

faders and buttons shown in the GEQ PARAM screen

(GEQ function).

In the DISPLAY ACCESS section, repeatedly

press the [GEQ] key to access the GEQ PARAM

screen.

GEQ ASSIGN

DSP CONFIGURATION box

Controlling the graphic EQ from the

display

MODULE box Spectrum analyzer

GEQ PARAM

Faders LIMIT area

GEQ/PEQ button

15 Graphic EQ and Parametric EQ

120 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Click the / buttons at the left and right of

the MODULE box to select the GEQ module

you want to operate.

At this time make sure that the GEQ ON/OFF button

is on. Also make sure that the corresponding module is

inserted into an appropriate channel, and that insert-

in/out is enabled for that channel.

Hint

• The upper part of the GEQ PARAM screen functions as a

spectrum analyzer. If a signal is being input to the corre-

sponding channel, the level of each frequency band is

displayed in realtime.

• As an alternate way to select the desired GEQ module, you

can use the GEQ ASSIGN screen (GEQ function) (

➥

p.173).

Click the GEQ button located in the upper

middle of the screen to select the 31-band

graphic EQ.

If desired, use the buttons of the LIMIT area to

specify the variable range of the faders.

The LIMIT area lets you select the maximum amount

and direction of the change controlled by the faders.

You can select ±15 dB/±12 dB/±6 dB (both boost and

cut directions) or –24 dB (cut only).

Drag the faders in the lower part of the screen

to adjust the amount of boost/cut.

The value of each fader is shown by the box below it.

Hint

Clicking the EQ FLAT button below the LIMIT area will reset

all faders to 0 dB.

Here’s how to control the graphic EQ using the keys and

faders of the panel DCA strip. In this case, the correspond-

ing graphic EQ is divided into six regions for control.

In the DISPLAY ACCESS section, repeatedly

press the [GEQ] key to access the GEQ PARAM

screen.

Click the / buttons at the left and right of

the MODULE box to select the GEQ module

you want to operate.

At this time, make sure that the GEQ ON/OFF button

is turned on. Also make sure that the corresponding

module is inserted into an appropriate channel, and

that insert is enabled for that channel.

Hint

When the GEQ PARAM screen is displayed, pressing the

[SEL] key of a channel in which a GEQ module is inserted will

recall the corresponding GEQ module in the screen.

Click the GEQ button located in the upper

middle of the screen to select the 31-band

graphic EQ.

Use the buttons of the LIMIT area to select the

maximum amount and direction of the change

controlled by the faders.

In the lower part of the screen, click a button

in the ASSIGN TO FADERS area to select the

region you will control from the DCA faders.

The buttons in the ASSIGN TO FADERS area corre-

spond to the following frequency regions.

When a button is clicked, you can use the DCA faders

to control the faders of that frequency region. The fad-

ers of the selected region are indicated by a red line in

the center of the fader.

While any of the buttons in the ASSIGN TO FADERS

area is on, you can use the FADER MODE section

FADER MODE [A]–[F] keys to select the frequency

region corresponding to these buttons.

Even if all of the buttons in the ASSIGN TO FADERS

area are off, you can hold down the [SHIFT] key and

press one of the FADER MODE [A]–[F] keys to select

the region to be controlled by the DCA faders.

Controlling the graphic EQ from the

DCA section

MODULE box EQ ON/OFFbutton

GEQ PARAM

LIMIT areaASSIGN TO FADERS area

GEQ/PEQ button

A 20.0-100 button The eight bands 20.0 Hz–100 Hz

B 63.0-315 button The eight bands 63.0 Hz–315 Hz

C 200-1.00k button The eight bands 200 Hz–1.00 kHz

D 630-3.15k button The eight bands 630 Hz–3.15 kHz

2.00k-10.0k button

The eight bands 2.00 kHz–10.0 kHz

4.00k-20.0k button

The eight bands 4.00 kHz–20.0 kHz

20.0Hz–100Hz 630Hz–3.15kHz

63.0Hz–315Hz 200Hz–1.00kHz

2.00kHz–10.0kHz

4.00kHz–20.0kHz

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 121

Graphic EQ and Parametric

Operate DCA faders 1–8.

The corresponding frequency region will be boosted or

cut.

Hint

If the fader of a graphic EQ is at the 0 dB position, the [NOMI-

NAL] LED of the DCA fader will light. If it is at other than the 0

dB position, the DCA [MUTE] key will light. While the DCA

[MUTE] key is lit, pressing the DCA [MUTE] key will reset the

corresponding band to 0 dB.

If you want to use the DCA faders to control a

different region, repeat steps 5–6.

When you have finished using the DCA faders

to control the graphic EQ, either press the

FADER MODE [DCA] key or click the OFF but-

ton in the ASSIGN TO FADERS area.

When the [DCA] button is on, the FADER MODE

keys and the DCA faders will return to their normal

state. If you once again want to assign the graphic EQ

to the DCA faders, either click a button in the ASSIGN

TO FADERS area or hold down the [SHIFT] key and

press a FADER MODE [A]–[F] key.

Hint

• GEQ module settings are saved as part of the scene. The

settings of a GEQ module can also be saved in the GEQ

library. For details, refer to GEQ LIBRARY screen (

➥

p.174)

in the Reference section.

• When you switch the display to a different screen, the DCA

fader assignments will be forcibly defeated, and will no

longer function even if you return to the GEQ screen. How-

ever if you turn on the AUTO ASSIGN button in the GEQ

PARAM screen, the DCA faders will automatically be

assigned to the most recently operated region when you

access the GEQ PARAM screen.

Basic parametric EQ operations

There are two ways to operate the parametric EQ: using the knobs and buttons in the display, or using the SELECTED

CHANNEL section of the panel.

Here’s how to use the knobs and buttons of the GEQ

PARAM screen (GEQ function) to operate the desired

parametric EQ.

In the DISPLAY ACCESS section, repeatedly

press the [GEQ] keys to access the GEQ

PARAM screen.

In the MODULE box, click the left/right /

buttons to select the GEQ module that you

want to operate.

Make sure that the EQ ON/OFF button is on. Also

make sure that the corresponding module is inserted

into the appropriate channel, and that insert in/out is

enabled for that channel.

Hint

An alternate way to select the desired GEQ module is to use

the GEQ ASSIGN screen (GEQ function) (

➥

p.173).

Click the PEQ button located in the upper mid-

dle of the screen to select the 8-band

parametric EQ.

If you want to use the LOW band or HIGH

band as a shelving-type EQ or as a high-pass or

low-pass filter, click the / button of that

band, or the HPF/LPF button to turn it on.

If you switch to a shelving type, the Q knob will disap-

pear. When you switch to a high-pass or low-pass filter,

the Q knob will disappear, and the GAIN knob will

change to the HPF/LPF on/off switch.

Using the Q knob, GAIN knob, and FREQ knob

of each band, specify the steepness, gain, and

center frequency for each band.

The value of each setting is shown in the box below.

Hint

If you click the EQ FLAT button, the boost/cut amount of all

bands will be reset to 0 dB.

Controlling the parametric EQ from

the display

MODULE box EQ ON/OFF button

GEQ PARAM

GEQ/PEQ button

15 Graphic EQ and Parametric EQ

122 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

You can use the keys and encoders in the SELECTED

CHANNEL section of the panel to operate the parametric

EQ.

In the DISPLAY ACCESS section, repeatedly

press the [GEQ] keys to access the GEQ

PARAM screen.

In the MODULE box, click the left/right /

buttons to select the GEQ module that you

want to operate.

Make sure that the EQ ON/OFF button is on. Also

make sure that the corresponding module is inserted

into the appropriate channel, and that insert in/out is

enabled for that channel.

Hint

If the GEQ PARAM screen is displayed, pressing the [SEL]

key of the channel in which the GEQ module is inserted will

recall the corresponding GEQ module to the screen.

Click the PEQ button located in the upper mid-

dle of the screen to select the 8-band

parametric EQ.

Click the ASSIGN TO SELECTED CH field ON

button to turn it on.

Use the SELECTED CHANNEL section EQUAL-

IZER controls to control the parametric EQ.

At this time you won’t be able to operate the

SELECTED CHANNEL section other than EQUAL-

IZER. For details on using the SELECTED CHANNEL

section, refer to p.65.

Hint

• GEQ module settings are saved as part of the scene. You

can also save desired GEQ module settings in a library. For

details, refer to the Reference section GEQ LIBRARY

screen

(

➥

p.174)

• When the display switches to another screen, the UPPER or

LOWER assignments are forcibly defeated, and you won’t

be able to operate this even if you once again access the

GEQ PARAM screen. However if you leave the ASSIGN TO

SELECTED CH field’s AUTO ASSIGN button on, the previ-

ously-operated band will automatically be assigned to the

SELECTED CHANNEL section when you access the GEQ

PARAM screen.

Controlling the parametric EQ from

the SELECTED CHANNEL section

MODULE box EQ ON/OFF button

GEQ PARAM

GEQ/PEQ button

SELECTED CHANNEL section

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 123

Remote control

This chapter explains how you can use MIDI or GPI to control the PM5D’s parameters from an

external device, or conversely how you can use the PM5D to control external devices.

MIDI on the PM5D

The PM5D can use MIDI to perform the following operations.

• Program Change transmission and reception

When you execute a specific event (scene/effect library

recall) on the PM5D, a program change message of the

corresponding number can be transmitted to an exter-

nal device. Conversely, the corresponding events can be

executed when program change messages are received

from an external device.

• Control Change transmission and reception

When you execute a specific event (fader/encoder or

key operation) on the PM5D, a control change mes-

sage of the corresponding number can be transmitted

to an external device. Conversely, events can be exe-

cuted when control change messages are received from

an external device. This capability can be used to

record fader and key operations on a MIDI sequencer

or other external device, and play back this data later.

System exclusive messages can also be used to transmit

or receive bulk data (scene or library content) or

parameters.

• MIDI Remote function

You can assign MIDI messages to the controls of the

INPUT/ST IN channel strip, and transmit those MIDI

messages by operating the controls. This capability can

be used for remote control of external MIDI devices

such as synthesizers, or to control the parameters of

DAW software or a HDR unit.

• MIDI Event transmission

MIDI messages can be registered independently for

each scene in scene memory, and transmitted when

that scene is recalled.

Note

For each of the above functions, the MIDI port used to trans-

mit/receive MIDI messages can be selected from the rear

panel MIDI IN/OUT connectors, the rear panel USB connec-

tor, and an I/O card installed in slots 1 through 4. (If the USB

connector or an I/O card is selected, you can additionally

choose from ports 1 through 8.) However, MIDI Event trans-

mission is fixed at the MIDI OUT connector.

Using program changes to control events

The PM5D lets you assign specific events (scene recall / effect library recall) to each MIDI program number, so that the corre-

spondingly-numbered program change message will be transmitted to an external device when you execute that event on the

PM5D. Conversely, the corresponding event can be executed when a program change message is received from an external

device.

Connect the MIDI OUT connector of the exter-

nal device to the PM5D’s MIDI IN connector.

Connect the MIDI OUT connector of the PM5D

to the MIDI IN connector of the external

device.

In the DISPLAY ACCESS section, press the

[MIDI/REMOTE] key several times to access the

MIDI PGM CHANGE screen shown below.

In the MIDI PGM CHANGE screen you can assign

events to each program number, select the port at

which MIDI messages will be transmitted and received,

and select how program changes will be transmitted

and received.

16 Remote control

MIDI IN MIDI OUT MIDI OUTMIDI IN

PM5D

External

device

MIDI PGM CHANGE

16 Remote control

124 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

In the PROGRAM CHANGE SETUP area at the

left of the screen, you can select the way in

which program changes will be transmitted

and received, and switch reception and trans-

mission on/off.

The MODE area of PROGRAM CHANGE SETUP lets

you choose one of the following as the way in which

program changes will be transmitted and received.

• SINGLE

If this button is on, program changes will be transmit-

ted/received on a single MIDI channel (Single mode).

• OMNI ON/OFF

If this button is on, program changes of all MIDI chan-

nels will be received in Single mode (this is unavailable

in Multi mode).

• BANK ON/OFF

If this button is on, bank select messages will be trans-

mitted and received in Single mode (this is unavailable

in Multi mode).

• MULTI

If this button is on, program changes will be transmit-

ted/received on multiple MIDI channels (Multi mode).

You can use the Tx (transmission) and Rx (reception)

buttons to turn program change transmission and

reception on/off separately.

In the MIDI SETUP area at the upper left of the

screen, select the port at which program

changes will be transmitted/received, and the

MIDI channel that will be used for transmis-

sion and reception. You have the following

choices.

Click the / buttons at the left and right of the Tx

box (transmission) or Rx box (reception) to change the

setting, and press the [ENTER] key (or click within the

box) to finalize the setting. If you select USB or SLOT

1–4, use the box at the right to specify the port number

(1–8) as well.

If SINGLE (single mode) is selected as the program

change transmission/reception mode, use the MIDI

CH field to select the MIDI transmit channel and MIDI

receive channel.

Hint

The MIDI port and MIDI channel used for program change

transmission/reception can also be specified from the MIDI

SETUP screen (

➥

p.188).

In the list at the right side of the screen, dis-

play the MIDI channel (bank) and program

number to which you want to assign an event,

and click that line.

This list lets you select the event (scene recall / effect

library recall) assigned to each program number.

The list contains the following columns.

• CH/BANK (Channel/Bank)

In Multi mode, or in Single mode when the BANK

ON/OFF button is off, the value in this column indi-

cates the MIDI channel on which program changes are

transmitted and received.

In Single mode when the BANK ON/OFF button is on,

the value in this column indicates the bank number.

• PGM No. (Program number)

Indicates the program number 1–128.

• LIBRARY NAME

In this column you can view/select the type and the

number of the event assigned to each channel (bank)/

program number.

Use the scroll bar at the right to display the desired

channel (bank) and program number, and click that

line; the line you click will move to the center and will

be highlighted.

Click the button in the LIBRARY NAME col-

umn of the currently selected line to open the

MIDI PGM CHANGE window.

MIDI The rear panel MIDI IN/OUT connectors

USB The rear panel USB connector

SLOT 1–4 An I/O card installed in rear panel slot 1–4

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 125

Remote control

In this window you can select the type of event (a

scene, or a library item for effect 1–8) and its number.

In the list at the left, select the type of event. In the list

at the right, select the scene/library number that will be

recalled. The following types of event can be selected in

the list at the left.

When you have finished making settings, click

the OK button in the MIDI PGM CHANGE

window.

Assign events to other program numbers in

the same way.

With these settings, executing the specified event on

the PM5D will cause a program change (or bank select

+ program change) message to be transmitted to the

external device.

When an external device transmits a program change

(or bank select + program change) message on the

appropriate channel, the event assigned to that pro-

gram number will be executed.

Hint

• You can use the CLEAR button above the list to erase all

assignments to program numbers. The PRESET button will

return all program number assignments to their default state.

• The contents of the program change table are not saved in

the scene. If desired, you can save this data on a memory

card as a MIDI PGM TABLE.

Note

If more than one program number is assigned to a single

scene, only the lowest-numbered program change will be

transmitted in Single mode, and in Multi mode the lowest-

numbered program change for each channel will be

transmitted.

Using control changes to control events

You can use MIDI control change messages to control specified events (fader/encoder operations, key on/off operations etc.)

on the PM5D. This capability can be used to record fader and key operations on a MIDI sequencer or other external device,

and play back this data later.

You can use control changes to control events in either of

the following two ways.

• Using control change numbers 1–119

This method uses the common variety of control

change messages. You can freely assign an event to each

control number.

• Using NRPN (Non Registered Parameter Number)

This method uses a special type of control change mes-

sages called NRPN. NRPN uses control change

numbers 99 and 98 to specify the MSB (Most Signifi-

cant Byte) and LSB (Least Significant Byte) of the

parameter number, and subsequently-transmitted con-

trol change messages of control change number 6 (or 6

and 38) to specify the value of that parameter.

The event specified by each combination of MSB and

LSB is fixed.

Connect the MIDI OUT connector of the exter-

nal device to the PM5D’s MIDI IN connector.

Connect the MIDI OUT connector of the PM5D

to the MIDI IN connector of the external

device.

In the DISPLAY ACCESS section, press the

[MIDI/REMOTE] key several times to access the

MIDI CTRL CHANGE screen shown below.

In the MIDI CTRL CHANGE screen you can select the

port used to transmit/receive MIDI messages, and how

control changes will be transmitted and received. If

control change 1–119 is selected as the transmission/

reception method, you can assign the desired event to

each control number.

NO ASSIGN No event is assigned

SCENE Scene memory recall

EFFECT 1–8

Recall an effect library item into an internal

effect module 1–8

Event type Scene/library number

MIDI CTRL CHANGE

16 Remote control

126 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

In the CONTROL CHANGE SETUP area at the

left of the screen, you can select the way in

which control changes will be transmitted and

received, and switch reception and transmis-

sion on/off.

The MODE area of CONTROL CHANGE SETUP lets

you choose one of the following as the way in which

control changes will be transmitted and received.

You can use the buttons in the Tx (transmission) area

and Rx (reception) area to turn control change trans-

mission/reception on/off.

In the MIDI SETUP area at the upper left of the

screen, select the port used to transmit/

receive control changes, and the MIDI chan-

nel used for transmission and reception.

In MIDI SETUP, the MIDI PORT settings let you select

the port used for MIDI control change transmission/

reception; you have the following choices.

Click the / buttons at the left and right of the Tx

box (transmission) or Rx box (reception) to change the

setting, and press the [ENTER] key to finalize the set-

ting. If you select USB or SLOT 1–4, use the box at the

right to specify the port number (1–8) as well.

If TABLE [SINGLE] or NRPN are selected as the con-

trol change transmission/reception method, use MIDI

CH field to choose the MIDI channel used for trans-

mission and reception.

Hint

The MIDI port and MIDI channel used for control change

transmission/reception can also be specified from the MIDI

SETUP screen (

➥

p.188).

If TABLE [SINGLE] or TABLE [MULTI] are

selected as the control change transmission/

reception method, use the list in the right of

the screen to display the MIDI channel and

control number to which you want to assign

an event, and click that line.

In this list you can select the event (fader/encoder oper-

ation, key operation, etc.) that will be assigned to each

control number. The list contains the following

columns.

• CH (Channel)

Indicates the MIDI channel on which the control

change is transmitted/received.

Note

You can use this column to specify multiple MIDI channels

even if TABLE [SINGLE] is selected as the transmission/

reception method. However in actuality, only the MIDI trans-

mit/receive channel selected in the MIDI SETUP field will be

valid.

• CTRL No. (Control number)

Indicates the control number 1–119. You cannot make

settings for numbers 0, 32, or 96–101.

• CTRL CHANGE EVENT (Library name)

Indicates/selects the type of event assigned to the corre-

sponding channel / control number.

Use the scroll bar at the right to display the desired

channel and control number, and click that line; the

line you click will move to the center and will be

highlighted.

Click the button in the CTRL CHANGE

EVENT column of the currently selected line to

open the MIDI CTRL CHANGE window, and

specify the parameter that you want to assign.

In this window you can specify the parameter in three

levels (mode, parameters 1/2).

When you have finished making settings, click

the OK button in the MIDI CTRL CHANGE

window.

Assign events to other control numbers in the

same way.

When you operate the parameters you assigned on the

PM5D, control change messages will be transmitted to

external devices.

Similarly, if the corresponding control change mes-

sages are sent from an external device on the

appropriate channel, the parameters assigned to those

control numbers will change.

NRPN

If this button is on, PM5D parameters

will be transmitted/received as NRPN

messages.

TABLE [SINGLE]

If this button is on, PM5D parameters

will be transmitted/received as control

change messages on a single MIDI

channel according to the assignments

in the list at the right side of the screen.

TABLE [MULTI]

If this button is on, PM5D parameters

will be transmitted/received as control

change messages on multiple MIDI

channels according to the assignments

in the list at the right side of the screen.

MIDI The rear panel MIDI IN/OUT connectors

USB The rear panel USB connector

SLOT 1–4 An I/O card installed in rear panel slot 1–4

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 127

Remote control

Hint

• You can use the CLEAR button above the list to erase all

assignments to control numbers. The PRESET button will

return all control number assignments to their default state.

• The contents of the control change table are not saved in

the scene. If desired, you can save this data on a memory

card as a MIDI CTRL TABLE.

Using the MIDI Remote function

“MIDI Remote” allows you to assign MIDI messages to the controllers (faders, encoders, CH [ON] keys, ENCODER [ON]

keys) of the INPUT/ST IN channel strips so that these MIDI messages will be transmitted when you operate these controllers.

This capability can be used for remote control of external MIDI devices such as synthesizers, or to control the parameters of

DAW software or a HDR unit.

While the MIDI Remote function is active, INPUT chan-

nel strip 1–24 functions as MIDI remote channels 1–24,

and ST IN channel strip 1–4 functions as MIDI remote

channels 25–28.

To each controller you can assign a MIDI message consist-

ing of up to sixteen bytes of hexadecimal data. If desired,

you can specify that a value within the message varies

according to the movement of the controller.

Here’s how to specify the MIDI port used by the MIDI

Remote function, and assign a MIDI message to the

desired MIDI remote channel.

In the DISPLAY ACCESS section, press the

[MIDI/REMOTE] key several times to access the

MIDI SETUP screen shown below.

In the MIDI REMOTE area at the right of the

screen, select one of the following as the port

from which MIDI messages will be output for

each of the four MIDI Remote banks (BANK A–

D).

Click the / buttons at the left and right of each

box to change the setting, and press the [ENTER] key

(or click within the box) to finalize the setting. If you

select USB or SLOT 1–4, use the box at the right to

specify the port number (1–8) as well.

MIDI remote channels 1–24 MIDI remote channels 25–28

MIDI The rear panel MIDI OUT connector

USB The rear panel USB connector

SLOT 1–4 An I/O card installed in rear panel slot 1–4

Assigning MIDI messages to controllers

MIDI SETUP

16 Remote control

128 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

In the DISPLAY ACCESS section, press the

[MIDI/REMOTE] key several times to access the

MIDI REMOTE screen shown below.

In the BANK SELECT area at the upper right of

the screen, use the A–D buttons to select the

bank you want to use.

The bank name is displayed above buttons A–D. You

can change the name by clicking the button at the

left of the bank name.

In the upper left of the screen, set the TRANS-

MIT ENABLED/DISABLED button to ENABLED.

Transmission will be enabled for the selected bank.

(You can enable/disable transmission for each of the

four banks.)

Use the channel select area at the left of the

screen to select the MIDI remote channel to

which you want to assign a MIDI message.

These buttons correspond to the following channel

strips.

When you click the / buttons at the left and right

of the box, the corresponding name is displayed in the

box at the right. You can change the name of the MIDI

remote channel by clicking the button of the box at

right.

Use the MIDI message boxes in the lower part

of the screen to specify a MIDI message for

each controller of the channel.

The lower part of the MIDI REMOTE screen contains

MIDI message boxes that let you assign a MIDI mes-

sage to the ENCODER [ON] key, encoder, CH [ON]

key, and fader.

You can assign a MIDI message to a controller in any

of the following three ways.

A Directly inputting hexadecimal values

In this method you directly input the message as hexa-

decimal values. To use this method, click the button

at the left edge of the desired MIDI message box to

open the MIDI REMOTE SETUP window.

In this window you can input a message by clicking the

desired input box to select it (the box will be high-

lighted) and turning the [DATA] encoder. You can use

the [INC]/[DEC] keys to move the selected position.

You can input the following values.

REMOTE CH 1–24 INPUT channel strip 1–24

REMOTE CH 25–28 ST IN channel strip 1–4

MIDI REMOTE

BANK SELECT area

Channel select area

TRANSMIT

ENABLED/DISABLED button

Value

Available

assign-

ments

Content

00(H)–

FF(H)

All

The MIDI message that is transmitted

(hexadecimal).

END All

Indicates the end of the MIDI mes-

sage. When you operate the corre-

sponding controller, the MIDI

message from the beginning until

immediately before END will be

transmitted.

SW All

Indicates the on/off status of the

encoder [ON] key or the channel

[ON] key. A value of 7F(H) is transmit-

ted when the key turns on, and a

value of 00(H) is transmitted when

the key turns off. If this is assigned to

an encoder or fader, the current value

of the key will be transmitted when

the encoder or fader is operated.

ENC

ENCODER

ON/

ENCODER

Indicates the current position of the

encoder. If assigned to an encoder, a

value of 00–7F(H) is transmitted

when the encoder is operated. If

assigned to an encoder [ON] key, the

current value of the encoder is trans-

mitted when the key is switched on.

FAD

CH ON/

FADER

Indicates the current position of the

fader. If the message is assigned to a

fader, this value is transmitted as a

value of 00–7F(H) when the fader is

operated. If assigned to a CH [ON]

key, the current value of the fader is

transmitted when the key is switched

on.

LEARN buttonLATCH button MIDI message box

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 129

Remote control

If you set a value to SW, ENC, or FAD, that value will

be linked to the state of the controller. For example if

you have made settings as shown in the following

screen, the last value will be linked with the fader posi-

tion, and will change in the range of 0–127.

When you click a box in which a hexadecimal value has

been input, the range of values that can be interpreted

as a valid MIDI message (including that box) will turn

red. The lower part of the screen shows the MIDI chan-

nel (MIDI CH), message type (TYPE), and data values

(DATA 1, DATA 2) for this MIDI message, letting you

verify that the appropriate MIDI message has been

input.

You can use the following buttons to input or edit the

message in this window.

When you have finished inputting data in the MIDI

REMOTE SETUP window, click the OK button. The

hexadecimal values will be input in the MIDI message

box of the MIDI REMOTE screen.

B Specifying the type of message

In this method you specify the desired MIDI channel,

type of message, and data value; these will be con-

verted into the appropriate hexadecimal values. Access

the MIDI REMOTE SETUP window in the same way

as for method

1, and click the first box into which

you want to input data.

Next, click the / buttons at the left and right of the

TYPE box to select the type of message.

Then use the MIDI CH, DATA 1, and DATA 2 boxes

to specify the MIDI channel and various values. The

values that can be selected in the MIDI CH, DATA 1,

and DATA 2 boxes will depend on the type of message

you selected first.

If you set the DATA 1 or DATA 2 value to SWITCH,

ENCODER (available only for encoders), or FADER

(available only for faders), that value will be linked with

the state of the controller.

buttons Move the highlighted area to left or right.

INS button

Inserts a space (blank) at the highlighted

position. Pressing the <Insert> key of a

PS/2 keyboard will produce the same

result.

DEL button

Deletes the character at the highlighted

position. Pressing the <Delete> key of a

PS/2 keyboard will produce the same

result.

CLEAR button

Erases the entire message that was input

in the MIDI message input boxes.

PASTE button

Pastes the message that was copied to

buffer memory by the COPY button.

COPY button

Copies the message from the MIDI mes-

sage input box to temporary buffer mem-

ory. Use this in conjunction with the PASTE

button to copy a message from one con-

troller to another bank or controller.

TYPE MIDI CH DATA 1 DATA 2

NOTE OFF

1–16

Note number

(0–127)

Note-off velocity

(0–127)

NOTE ON

Note-on velocity

(0–127)

KEY PRES-

SURE

Pressure value

(0–127)

CONTROL

CHANGE

Control num-

ber (0–127)

Controller value

(0–127)

PROGRAM

CHANGE

Program

number

—

CHANNEL

PRESSURE

Pressure

value (0–127)

PITCH BEND

Pitch bend

MSB (0–127)

Pitch bend LSB

(0–127)

EXCLUSIVE

MESSAGE

—

Hexadecimal values that were input

Type of message

16 Remote control

130 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

When you have specified all of the values, click the

“” button in the screen; the hexadecimal val-

ues for that message will be input in the input box of

the MIDI REMOTE SETUP window. As necessary, you

can edit the message by clicking an input box and turn-

ing the [DATA] encoder.

C Using the LEARN button

The LEARN button lets you assign a MIDI message to

a controller by receiving that message from an external

device. To use the Learn function, go to the MIDI

REMOTE screen and click the LEARN button in for

the controller to which you want to assign a message.

Note

• Only one LEARN button can be turned on simultaneously.

• The LEARN button is valid only for the MIDI remote channel

that is currently selected. Also, you cannot change the MIDI

remote channel while this button is on.

• The LEARN button is turned off automatically when you

switch to a different screen.

If a MIDI message is received at a MIDI port available

for the current bank while the LEARN button is on, the

received message will be input to the MIDI input box.

The following screen shows an example of when the

modulation wheel (control change #1) of a synthesizer

is operated.

Hint

• MIDI messages assigned using the LEARN button can be a

maximum of 16 bytes long (the 17th and subsequent bytes

are discarded). If the message is less than 16 bytes long,

END will be placed immediately after the last data value.

• If a control change is received, the third byte will automati-

cally be replaced by FAD (if the assignment destination is a

fader), ENC (if the assignment destination is an encoder), or

SW (if the assignment destination is an encoder [ON] or CH

[ON] key).

• If multiple messages are received while the LEARN button is

on, the last-received message will be used. If the status byte

is omitted from the last message, the appropriate status byte

will be supplied.

Assign messages to other MIDI remote chan-

nels or other banks in the same way.

If a specific byte is set to “SW” for the ENCODER

[ON] key or CH [ON] key, use the LATCH button to

select one of the following behaviors.

• If the LATCH button is on

The on/off status will change each time you press the

key (Latched). If you press the key from the Off state, a

MIDI message with 7F(H) as the SW value will be

transmitted, and when you press the same key once

again a MIDI message with 00(H) as the SW value will

be transmitted.

• If the LATCH button is off

The switch will be on only while you are holding it

down, and will turn off when you release it

(Unlatched). The moment you press the key, a MIDI

message with 7F(H) as the SW value will be transmit-

ted; the moment you release the key, a MIDI message

with a SW value of 00(H) will be transmitted.

If a specific byte is set to “ENC” (or “FAD”) for the

ENCODER [ON] key or CH [ON] key, use the

LATCH button to select one of the following

behaviors.

• If the LATCH button is on

If you press the key from the Off state, a MIDI message

with the current value of the encoder (or fader) as the

ENC (or FAD) value will be transmitted, and when you

press the same key once again a MIDI message with

00(H) as the ENC (or FAD) value will be transmitted.

• If the LATCH button is off

The moment you press the key, a MIDI message with

the current value of the encoder (or fader) as the ENC

(or FAD) value will be transmitted, and the moment

you release the key a MIDI message with 00(H) as the

ENC (or FAD) value will be transmitted.

Note

If SW/ENC/FAD are not specified as the last byte of the MIDI

message, the same MIDI message will be transmitted when

the key is turned on or off. (The same message will be trans-

mitted when the key is turned off.)

Hexadecimal values that were input

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 131

Remote control

Here’s how to recall banks A–D to which you assigned

MIDI messages, and operate MIDI remote channels.

In the DISPLAY ACCESS section, press the

[MIDI/REMOTE] key several times to access the

following MIDI REMOTE screen.

In the BANK SELECT area at the upper right of

the screen, use the A–D buttons to select the

bank you want to use.

In the upper middle of the screen, use the

ASSIGN TO CH STRIP SECTION buttons to

select the MIDI remote channel you want to

control. (Multiple simultaneous selections are

allowed.)

This setting applies to all four banks.

Turning on a button will enable the MIDI Remote

function; the corresponding channel strip will func-

tion as MIDI remote channels. (The usual function of

the controllers will be disabled.)

At this time, the lower part of the display will indicate

“REMOTE” in the encoder/fader mode area. The

INPUT CH layer and ST IN/FX RTN layer indications

will change to the corresponding MIDI remote

channel.

Operate the appropriate channel strip.

MIDI messages will be transmitted from the corre-

sponding MIDI port.

To disable the MIDI Remote function, turn off

the ASSIGN TO CH STRIP SECTION buttons.

Note

• When the MIDI Remote function is enabled, the controllers

will return to their normal state if you switch to another

screen. However when you come back to the MIDI

REMOTE screen, the remote function of the controllers will

be enabled.

• The controller values during MIDI Remote operation are

included in the scene data. This means that when you recall

a scene, the controller values will change and MIDI mes-

sages will be transmitted. Recall Safe settings can also be

applied to the MIDI Remote function.

INPUT CH INPUT channel strip 1–24

STIN/FXRTN ST IN/FX RTN channel strip 1–4

Using MIDI remote channels

MIDI REMOTE BANK SELECT area

ST IN/FX RTN

layer

INPUT CH

layer

Encoder/fader

mode area

16 Remote control

132 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Transmitting MIDI events when you switch scenes

You can register a desired MIDI message for each scene in scene memory so that this message will be transmitted from the

MIDI OUT connector when you recall the scene. For example you can use this to switch programs on an external MIDI-com-

patible effect processor when the scene changes.

Connect the MIDI OUT connector of the PM5D

to the MIDI IN connector of the external

device.

In the DISPLAY ACCESS section, press the

[SCENE] key several times to access the SCENE

screen shown below.

Scroll the scene list upward or downward to

select the scene number for which you want to

assign a MIDI event.

Scroll the scene list toward the right to dis-

play the MIDI EVENT column.

In the MIDI EVENT column you will input the MIDI

message that will be transmitted when you recall that

scene.

Click the button at the left edge of the MIDI

EVENT column to open the MIDI EVENT SETUP

window.

Use the MIDI EVENT SETUP window to specify

the MIDI message that will be linked with that

scene.

The procedure for specifying a MIDI message in the

MIDI EVENT SETUP window is the same as in the

MIDI REMOTE screen MIDI REMOTE SETUP win-

dow, with the exceptions that you cannot select FAD,

ENC, or SW for the DATA 1/DATA 2 boxes, and that

there is no LEARN button. (For details, refer to p.128)

When you have finished making settings, click the OK

button in the MIDI EVENT SETUP window.

Click the Tx ON/OFF

column located at the

right of the MIDI EVENT

column to turn it on.

The MIDI event linked to

the corresponding scene is

now enabled.

Note

If necessary, you can adjust the

timing at which the MIDI events

linked to the scene are trans-

mitted (

➥

p.176).

In the same way, specify MIDI events for other

scene numbers.

Recall a scene to which a MIDI event is linked.

The MIDI message will be transmitted from the speci-

fied MIDI port.

SCENE

MIDI EVENT column

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 133

Remote control

Using GPI (General Purpose Interface)

The GPI connector on the rear panel can be used as a GPI (General Purpose Interface) input/output connector. This connec-

tor provides four GPI IN ports and twelve GPI OUT ports. For example you can use an external switch or joystick to control

the PM5D’s parameters, or conversely use the PM5D’s keys and faders to send control signals to an external device.

The following diagram is an example of an external circuit

that can operate GPI via the GPI connector. (For specifica-

tions of the GPI connector pins, refer to the Appendices

p.388 and p.394 at the end of the manual.)

This circuit uses four switches (GPI 1–GPI 4) to switch the

GPI IN ports between active and inactive. If the polarity of

a GPI OUT port is set to Low Active, and you operate the

PM5D to make the GPI OUT port Active, the correspond-

ing LED in the above circuit (GPO 1–GPO 12) will light.

(If the polarity of the GPI OUT port is High Active, the

LED will go dark.)

You can use the GPI IN ports of the GPI connector to con-

trol PM5D parameters from an external device. For

example you can use an external switch to turn the

PM5D’s talkback on/off or to operate its Tap Tempo func-

tion, or you can use a joystick to control surround

panning.

Connect an external device to the PM5D’s GPI

connector.

In the DISPLAY ACCESS section, press the

[MIDI/REMOTE] key several times to access the

GPI screen shown below.

In this screen, the upper list is used to make GPI IN

settings and the lower list is used to make GPI OUT

settings.

In the POLARITY column of the GPI IN list,

select the polarity of each GPI IN port.

You can select one of the following as the polarity for a

GPI IN port.

• (Low active)

When controlling an on/off switch-type parameter, the

port will become active when the switch is grounded.

When controlling a continuously-variable parameter,

that parameter will be at its maximum value when the

voltage is at low level (by default, 0V), and at its mini-

mum value when the voltage is at high level (by default,

approximately 5V).

• (High active)

When controlling an on/off switch-type parameter, the

port will be active when the switch is opened or when a

high-level voltage is input.

9 1 21 14 9 2 21 15

GPO 1 GPO 2 GPO 3 GPO 4

9 3 21 16 9 4 21 17

GPO 5 GPO 6 GPO 7 GPO 8

21 24 9 12 21 25 9 13

GPO 9 GPO 10 GPO 11 GPO 12

GPI 1 GPI 2

GPI 3 GPI 4

22 18 10 6 23 19 11 7

Using GPI IN

GPIGPI IN list

GPI OUT list

16 Remote control

134 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

When controlling a continuously-variable parameter,

that parameter will be at its minimum value when the

voltage is at low level, and at its maximum value when

the voltage is at high level.

While the GPI screen is displayed, the GPI IN status

column of the GPI IN area will show a yellow bar

graph to indicate the approximate value of the voltage

being input to each port. (If the bar is not shown, the

voltage is grounded; if the bar is displayed all the way

to the right edge, the voltage is at high level.)

Hint

The voltage value at which the PM5D detects High or Low

level can be adjusted to suit the external controller (except for

external switches) you are using (

➥

p.135).

At the left edge of the FUNCTION column,

click the button to open the GPI IN PORT

ASSIGN window.

In the GPI IN PORT ASSIGN window you can select

the PM5D function that will be controlled by each GPI

IN port.

Use the FUNCTION column to select the type of func-

tion, and use the PARAMETER column to select the

optional parameters. You can select the following func-

tions and parameters.

After you have specified the function and parameter,

click the OK button.

Note

• If latched operation is selected, the port will change between

active/inactive each time a trigger is input from an external

switch. In this case, we recommend that you use a non-lock-

ing type of external switch.

• If unlatched operation is selected, the port will be active only

while the signal from the external switch stays at high level

or low level. In this case, we recommend that you use either

a non-locking or a locking type of external switch as appro-

priate for your situation.

FUNCTION PARAMETER PM5D operation

ASSIGN

— No assignment

MONITOR

DIMMER ON

Switches the Dimmer func-

tion on/off

SOURCE =

[monitor

source name]

Switches the monitor source

MONO ON

Switches the Monitor section

[MONO] key on

PARAMETER

column

FUNCTION columnGPI IN

status

POLARITY column

TALK-

BACK ON

LATCH

Switches the Talkback func-

tion on/off (latched operation)

UNLATCH

Switches the Talkback func-

tion on/off (unlatched opera-

tion)

CH ON-

LATCH

[channel

name]

Switches the channel on/off

(latched operation)

CH ON-

UNLATCH

[channel

name]

Switches the channel on/off

(unlatched operation)

FADER

LEVEL

[channel

name]

Modiﬁes the fader value

(LEVEL parameter) accord-

ing to the voltage

SUR-

ROUND

PA N

FRONT-REAR

PAN [SEL]

Modiﬁes the surround pan-

ning (front/rear) of the

selected channel according

to the voltage

LEFT-RIGHT

PAN [SEL]

Modiﬁes the surround pan-

ning (left/right) of the selected

channel according to the volt-

age

FRONT-REAR

PAN [ODD]

Modiﬁes the surround pan-

ning (front/rear) of the

selected odd-numbered

channel according to the volt-

age

LEFT-RIGHT

PAN [ODD]

Modiﬁes the surround pan-

ning (left/right) of the selected

odd-numbered channel

according to the voltage

FRONT-REAR

PAN [EVEN]

Modiﬁes the surround pan-

ning (front/rear) of the

selected even-numbered

channel according to the volt-

age

LEFT-RIGHT

PAN [EVEN]

Modiﬁes the surround pan-

ning (left/right) of the selected

even-numbered channel

according to the voltage

USER

DEFINED

KEY

FUNCTION

[User Deﬁned

key bank / key

number]

While the external input is

active, executes the same

operation as when the

selected User Deﬁned key is

pressed

USER

DEFINED

KEY LED

[User Deﬁned

key bank / key

number]

While the external input is

active, lights the LED of the

selected User Deﬁned key

PEAK

HOLD ON

—

Switches the Peak Hold func-

tion on/off

OSCILLA-

TOR ON

Switches the Oscillator on/off

SOLO ON

Switches the Solo function

on/off

FUNCTION PARAMETER PM5D operation

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 135

Remote control

Specify the function and parameter for other

GPI IN ports in the same way.

With these settings when you operate an external

device to make the GPI IN port active, the correspond-

ing PM5D function will be executed. (If a

continuously-variable parameter is assigned, the

parameter value will vary according to the change in

voltage.)

Hint

The settings in the GPI screen apply to all scenes. These set-

tings can also be saved on a memory card as SETUP data.

If necessary, the voltage values at which the PM5D detects

Low and High levels can be adjusted appropriately for the

voltage of the signals being input from the GPI IN port.

You can use this to set the variable range of a PM5D

parameter to match the range of voltage change produced

by a continuously-variable controller (such as a joystick).

Connect an external device to the PM5D’s GPI

connector.

In the DISPLAY ACCESS section, press the

[MIDI/REMOTE] key several times to access the

GPI screen.

In the GPI IN MONITOR area at the upper

right of the screen, select the GPI IN port that

you want to calibrate.

If you are calibrating a two-dimensional controller

such as a joystick, click the / buttons at the left

and right of the X-AXIS and Y-AXIS fields to specify

the two GPI IN ports.

If you are calibrating only one GPI IN port, set one of

them to “----” (no assignment).

When you specify a GPI IN port, the voltage from that

GPI IN port is indicated by a yellow symbol in the

GPI IN monitor area. In this case, the horizontal posi-

tion (X-axis) corresponds to the voltage of the GPI IN

port selected in the X-AXIS field, and the vertical posi-

tion (Y-axis) corresponds to the voltage of the GPI IN

port selected in the Y-AXIS field.

The red line (or red square) displayed in the GPI IN

monitor area indicates the range between High level

and Low level for the GPI IN ports corresponding to

the Y-axis and X-axis.

Hint

If necessary, you can click the REVERSE button to invert the

Low level and High level of the input signal. (The result is the

same as switching the POLARITY setting of the GPI IN port.)

Turn on the CALIBRATION button.

The red line (or red square) in the GPI IN monitor

area will temporarily disappear, and only the yellow

symbol will remain.

If you are calibrating only one GPI IN port,

vary the voltage of the signal being input to

the GPI IN port specified in step 3 from the

maximum value to the minimum value.

The yellow symbol will move up/down or left/right

as the voltage changes. The red line will extend accord-

ing to this change, and the maximum and minimum

voltage values for the corresponding GPI IN port will

be stored.

If you are calibrating a joystick, move the joy-

stick through a 360-degree path.

The yellow symbol will rotate. The red square will

broaden accordingly, and the maximum and mini-

mum voltage values of the GPI IN ports corresponding

to the X-axis and Y-axis will be stored.

Turn off the CALIBRATION button.

The maximum and minimum voltage values detected

will be remembered as the reference values for the

High and Low levels. (When controlling a continu-

ously variable parameter, the maximum value and

minimum value of that parameter will be aligned with

these reference values.)

Hint

The results of calibration apply to all scenes. They are also

preserved even when the PM5D is powered-off.

Calibrating the GPI IN ports

16 Remote control

136 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Here’s how you can use the GPI OUT ports of the GPI

connector to control an external device from the PM5D’s

faders or keys.

To the PM5D’s GPI connector, connect the

external device that you want to control from

the PM5D.

In the DISPLAY ACCESS section, press the

[MIDI/REMOTE] key several times to access the

GPI screen.

In the POLARITY column of the GPI OUT area,

select the polarity of the signal that is output

from each GPI OUT port.

The POLARITY column of the GPI OUT area selects

one of the following two settings as the polarity of the

signal that is output when the GPI OUT port becomes

active.

• (Low active)

Grounded when the GPI OUT port is active.

• (High active)

Open when the GPI OUT port is active.

In the GPI OUT area, use the FADER START,

USER DEFINED KEYS, and TALLY columns to

select the PM5D function for GPI OUT ports 1

through 12.

When an operation selected here is executed on the

PM5D, the corresponding GPI OUT port will become

active, and a control signal will be output.

For each GPI OUT port you can select the following

three functions (multiple selections are allowed).

❏ FADER START

A fader operation on the PM5D will be the trigger for out-

putting a signal from the GPI OUT port.

To edit the setting, click the button at the left to open

the GPI OUT PORT ASSIGN window, and select the fader

mode (trigger detection method) and channel. You can

select the following fader modes.

• FADER START

A control signal (trigger signal) 250 msec long will be

output when the fader of the selected channel moves

from –60 dB or below to above –60 dB.

• FADER STOP

A control signal (trigger signal) 250 msec long will be

output when the fader of the selected channel reaches

–∞ dB.

• FADER TALLY

A control signal will be output when the fader of the

selected channel moves from –60 dB or below to above

–60 dB. This control signal will be held until the fader

reaches –∞ dB (or until that GPI OUT port receives a

different trigger).

The following illustration shows how the output signal

from the GPI OUT port changes when you operate a

fader in each of the fader modes. (This illustration

shows operation when is selected as the POLAR-

ITY of the GPI OUT port. If POLARITY is , the

polarity of the output signal will be the opposite.)

Note

When the voltage is at High level, the output signal of the port

will be open. If the receiving device requires High level, it can

be taken from the +5 power supply pin. However in this case

there is a limitation on the current flow; for details, refer to the

Appendices at the end of this manual.

Using GPI OUT

TALLY columnFADER START column

GPI OUT

status

POLARITY column

TEST button

USER DEFINED KEYS

column

FADER

START

FADER

STOP

FADER

TALLY

➪

➠

➪➪➪➪

250 msec

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 137

Remote control

❏ USER DEFINED KEYS

Operation of a User Defined key on the PM5D will be the

trigger for outputting a signal from the GPI OUT port.

To edit the setting, click the button at the left to open

the GPI OUT PORT ASSIGN window; from the list, select

the User Defined key bank (A–D) and number (1–25), and

choose the trigger mode (how the trigger will operate when

the key is pressed). You can choose one of the following

trigger modes.

• LATCH

Alternate between active and inactive each time the key

is pressed.

• UNLATCH

Active only while the key remains pressed.

The following illustration shows how the output signal

from the GPI OUT port changes when you operate a

User Defined key in each of the trigger modes. (This

illustration shows operation when is selected as the

POLARITY of the GPI OUT port. If POLARITY is ,

the polarity of the output signal will be the opposite.)

❏ TALLY (other)

Other operations on the PM5D will be the trigger for out-

putting a signal from the GPI OUT port. When the

corresponding operation is executed on the PM5D, a con-

trol signal will be output. This control signal will be held

until you defeat the above operation (or until that GPI

OUT port receives a different trigger).

To edit the settings, click the button at the left to open

the GPI OUT PORT ASSIGN window, and select one of

the following functions.

Make settings for other GPI OUT ports in the

same way.

With these settings, executing an operation assigned to

the GPI OUT port will output a control signal accord-

ing to the POLARITY setting.

You can use the TEST buttons in the GPI OUT area to

check the operation of the GPI OUT ports. When a

TEST button is on, the corresponding GPI OUT port

will become active, and a control signal will be output.

The GPI OUT status column indicates the status of the

output signal of the corresponding port. The charac-

ters L/H indicate the Low or High level of the signal.

The background color is yellow when active, and gray

when inactive.

LATCH

UNLATCH

Function PM5D operation

NO ASSIGN No assignment

POWER ON The PM5D’s power is turned on

SOLO ON [SOLO] key is turned on

GPI IN 1

FUNCTION

The function assigned to GPI IN port 1

becomes active

GPI IN 2

FUNCTION

The function assigned to GPI IN port 2

becomes active

GPI IN 3

FUNCTION

The function assigned to GPI IN port 3

becomes active

GPI IN 4

FUNCTION

The function assigned to GPI IN port 4

becomes active

PREVIEW ON

SCENE MEMORY section [PREVIEW] key is

turned on

CUE ON

[INPUT ONLY]

Input channel [CUE] key is turned on

CUE ON

[DCA ONLY]

DCA [CUE] key is turned on

CUE ON

[OUTPUT

ONLY]

Output channel [CUE] key is turned on

CUE ON Any [CUE] key is turned on

17 Using memory cards

138 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

This chapter explains how to save/load PM5D/DSP5D internal data using a memory card.

Using memory cards with the PM5D

You can insert a commercially available memory card into

the memory card slot located on the front panel of the

PM5D, and use it to save or load various types of data.

You can use PCMCIA Type II PC flash ATA cards, or

CompactFlash media inserted in a PC card adaptor. (In

either case, media with a power supply voltage of 3.3V or

5V is supported.) Normally, these cards are sold in an

already-formatted state. This means that you won’t need to

format them before using them with the PM5D. If you do

need to format a card, use a computer or other external

device to format the card in FAT16 format.

Note

Operation is not guaranteed for any type of media other than

described above.

Saving ﬁles to a memory card

Here’s how to save individual items of data (or all data) from the PM5D/DSP5D onto a memory card. If the PM5D and

DSP5D are cascade-connected, the settings of each machine can be consecutively saved by a single operation.

Insert the memory card into the memory card

slot located on the front panel of the PM5D.

You may insert or remove cards while the PM5D is

powered-on.

In the DISPLAY ACCESS section, repeatedly

press the [UTILITY] key to access the SAVE

screen.

In the left side of the SAVE screen you can select the

save mode and the item(s) that will be saved. The file

list in the right side of the screen contains four col-

umns; FILE NAME, TYPE, DATE/SIZE, and

COMMENT. This list shows the files and directories

on the memory card. (To see the COMMENT col-

umn, scroll the list toward the right.)

In the MODE area, click the BASIC button to

select BASIC as the save mode.

If BASIC mode is selected, you can choose the desired

item (or all items) and save them to a memory card.

Hint

The other save modes provided are ADVANCED mode which

lets you save scene memories or libraries under different

numbers, and CSV EXPORT mode which lets you save the

names of scene memories or libraries as a CSV format file.

For details, refer to the Reference section (

➥

p.212).

Note

If a DSP5D (machine #2 or #3) is selected, you can’t save

CSV format files. Please use DSP5D Editor.

Use the buttons below the MODE area to

select the item you want to save.

The item whose button is turned on is selected for sav-

ing. (You can turn on only one button.) By clicking the

ALL DATA button you can select all items at once.

These buttons correspond to the following items.

17 Using memory cards

PHONES

KEYBOARD

MOUSE

MEMORY CARD

SAVE

SAVE button

MODE area

File list

Button Content

ALL DATA

All items, and the contents of the cur-

rent scene

SCENE MEMORY Contents of scene memory

LINKED LIBRARY

Libraries linked to the scene (available

only if the SCENE MEMORY button is

on)

HA Contents of the HA library

INPUT PATCH Contents of the input patch library

OUTPUT PATCH Contents of the output patch library

INPUT CH Contents of the input channel library

OUTPUT CH Contents of the output channel library

INPUT EQ Contents of the input EQ library

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 139

Using memory cards

If you select the SCENE MEMORY, HA, INPUT

PATCH, or OUTPUT PATCH items, you can specify

the starting number and ending number so that only

the desired range of scenes or library items will be

saved. The LINKED LIBRARY button is available only

if the SCENE MEMORY button is on.

Hint

The TOTAL SIZE field at the bottom of the MODE area indi-

cates the file size for the selected item(s). The available

capacity of the inserted memory card is shown below the file

list.

If you selected scenes or libraries for saving,

use the boxes at the right of the button to

specify the starting number and ending

number.

As necessary, use the file list to select the

directory (folder) in which you will save the

data.

If the file list contains a directory below the current

level, the TYPE column will indicate “[DIR].”

To move to a lower directory, click the directory line to

select it (that line will move to the center of the list),

and click the directory name shown in the FILE NAME

column.

If the file list contains a directory above the current

level, it will be shown as “. .” in the FILE NAME col-

umn and “[DIR]” in the TYPE column.

To move to a higher directory, click the directory line

to select it (that line will move to the center of the list),

and click the “. .” shown in the FILE NAME column.

Hint

• The directory currently selected as the save destination is

also shown in the FILE PATH field above the list

• If you want to create a new directory in the current location,

click the MAKE DIR button below the file list.

Note

• The file list can display only up to one hundred items.

• Saving is not possible if the FILE PATH field exceeds 60

characters (including the filename extension).

After specifying the item to be saved and the

save-destination directory, click the SAVE

button.

The FILE SAVE window will appear, allowing you to

assign a name to the data that will be saved.

Use the character palette to input a filename,

and click the OK button.

A window will ask you to confirm the Save operation.

Note

• When assigning a name to a file on a memory card, lower-

case alphabetical characters and some symbols in the

character palette cannot be used.

• If you paste text copied from another character palette when

inputting the file name, all lowercase alphabetical charac-

ters will be converted to uppercase.

OUTPUT EQ Contents of the output EQ library

GATE Contents of the gate library

COMP Contents of the compressor library

EFFECT Contents of the effect library

GEQ Contents of the GEQ library

SETUP Various settings not saved in a scene

USER DEFINED

KEY

User Deﬁned key settings

DCA FADER

MODE

DCA fader mode settings

MIDI REMOTE MIDI remote settings

MIDI PGM TABLE

Contents of the list in the MIDI PGM

CHANGE screen

MIDI CTRL TABLE

Contents of the list in the MIDI CTRL

CHANGE screen

EVENT LIST

Contents of the list in the EVENT LIST

screen

Button Content

Starting number Ending number

Scene/library name

A directory below the current level

A directory above the current level

17 Using memory cards

140 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

To execute the Save operation, click the OK

button.

A window will appear, indicating the progress of the

Save operation. If you click the CANCEL button

instead of the OK button, the Save operation will be

aborted.

Do not insert or remove the memory card while it is being

accessed. A BUSY indicator at the upper right of the display

will light while the card is being accessed.

If the PM5D and DSP5D are cascade-con-

nected, a window will appear in which you

can save the settings of the second and sub-

sequent machines (DSP5D).

As necessary, repeat steps 7–9 to save the settings for

each machine individually. If you don’t need the set-

tings for the second and subsequent machine, click

the CANCEL button to abort the save operation.

When the save operation is finished, you will return

to the previous screen.

Hint

To avoid loading the data into the wrong machine, in the FILE

SAVE window that appears, the machine ID number (2 or 3)

will automatically be appended to the end of the file name for

the second and subsequent units.

Loading ﬁles from a memory card

Here’s how to load data from a memory card into the PM5D/PM5D.

Insert the memory card containing the data

you want to load into the memory card slot

located on the front panel of the PM5D.

If the PM5D and DSP5D are cascade-con-

nected, switch to the machine into which you

want to load the settings.

For details on how to switch the machine that is the

target of panel control, refer to p.40.

In the DISPLAY ACCESS section, repeatedly

press the [UTILITY] key to access the LOAD

screen.

As necessary, use the file list to specify the

load-source directory.

Navigation between directories is the same as in the file

list of the SAVE screen (➥ p.139). The currently

selected directory is also shown in the FILE PATH field

above the list.

In the file list, click the line showing the file

you want to load.

That file will move to the center of the list, and will be

highlighted.

The file list shows the following information.

• FILE NAME column

This column shows the names of the files saved on the

memory card. If a directory is selected, the directory

name is shown.

• TYPE column

This column shows the content that was saved. The

indication in the TYPE column will be one of the

following.

Hint

For scene memory data, the type can be either “SCENE” in

which only scene memory data is saved, and “SCENE+LIB” in

which linked libraries are included.

• DATE/SIZE column

This shows the date on which the file was last saved,

and its size. If a directory is selected, only the date is

shown.

LOAD

LOAD button

MODE area

File list

ALL A ﬁle in which all items were saved

[DIR] A directory

UNKNOWN A ﬁle that cannot be loaded by the PM5D

Other A ﬁle in which a speciﬁc item was saved

FILE NAME

column

DATE/SIZE columnTYPE column

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual

Operating section

141

Using memory cards

• COMMENT column

This shows the comment assigned when the file was

saved. To input a comment, scroll the file list horizon-

tally and click the COMMENT column for the

currently selected file.

Hint

By clicking the headings at the top of the list, you can sort the

list in ascending or descending order of that item. The text of

the currently selected button will turn red, and an arrow indi-

cating ascending (

↑

) or descending (

↓

) order will appear.

In the MODE area, click the BASIC button to

select BASIC as the loading mode.

Similarly to the Save mode in the SAVE screen, you can

choose either BASIC, ADVANCED, or CSV IMPORT

as the Load mode. If BASIC mode is selected, the item

buttons appropriate for the currently selected file will

turn on.

Hint

• If ADVANCED mode is selected, you can specify the range

of scenes or library numbers that will be loaded from a

scene memory and/or library file saved in BASIC mode or

ADVANCED mode.

• If CSV IMPORT is selected, you can load CSV files that

were saved in CSV EXPORT mode. For details on each

mode, refer to the Reference section (

➥

p.212).

Note

• If you select a directory in the file list, the Load mode will

automatically switch to CSV IMPORT, and the screen will

indicate whether that directory contains any CSV files. If you

subsequently select any file readable by the PM5D other

than a CSV file, the mode will automatically switch to

BASIC.

• If the type of file to be loaded is ALL DATA, the entire con-

tents of the PM5D/DSP5D’s scene memories and libraries

will be rewritten. Before loading, make sure you are not acci-

dentally overwriting important scenes or library data.

• If a DSP5D (machine #2 or #3) is selected as the target of

control, CSV files can’t be loaded. If you need to load a CSV

file, please use DSP5D Editor.

When loading scenes or libraries, you can click

the / buttons at the left and right of the

boxes beside each button to select the scene

or library numbers that will be loaded.

Click the LOAD button.

A window will ask you to confirm the Load operation.

To execute the Load operation, click the OK

button.

Note

Loading cannot be executed if cascade connection is enabled.

A window will appear, indicating the progress of the

Load operation. When loading is completed, the previ-

ous screen will reappear.

If you click the CANCEL button instead of the OK but-

ton, the Load operation will be aborted and you will

return to the previous screen.

Do not insert or remove the memory card while it is being

accessed. A BUSY indicator at the upper right of the display

will light while the card is being accessed.

Note

• If the LOAD LOCK button is on, synchronization can occur

only from this unit to PM5D Editor/DSP5D Editor (not the

reverse) when synchronizing with PM5D Editor/DSP5D

Editor.

• Be aware that scene memories for which “R” (read only) is

indicated in the SCENE function SCENE screen will not be

loaded, but the linked libraries will be loaded.

18 Surround pan

142 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

This chapter explains how to use the surround pan functionality.

About surround pan

“Surround pan” is functionality that, when used with a multi-channel playback system, lets you place the signal of an input

channel in two-dimensional space or move the sound image between front/back and left/right. (To move the surround pan

image, you can use the mouse, the CURSOR [√]/[®]/[π]/[†] keys, or the MIX encoders etc.)

The PM5D lets you choose from the following three surround modes, depending on the number of channels in your sur-

round environment.

• 3-1ch

This mode uses four channels; left and right front,

front center, and rear (surround).

• 5.1ch

This mode uses six channels; left and right front, left

and right rear, front center, and subwoofer.

• 6.1ch

This mode uses seven channels; 5.1ch with the addi-

tion of rear center.

Hint

The surround mode can be selected in the MIXER SETUP

screen (SYS/W.CLOCK function) or SURR SETUP screen

(MATRIX/ST function).

18 Surround pan

Front L Center Front R

Rear (surround)

Subwoofer

Rear L Rear R

Front L Center Front R

Subwoofer

Rear L Rear R

Front L Center Front R

Rear center

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 143

Surround pan

Bus conﬁguration and operation in surround mode

When any of the three surround modes (3-1ch, 5.1ch, 6.1ch) are selected, the PM5D’s bus configuration and operation will

change as follows.

While a surround mode is selected, MIX buses 1–8 or MIX

buses 9–16 can be used as surround buses. (The choice of

whether to use MIX buses 1–8 or MIX buses 9–16 is made

in the MATRIX/ST function SURR SETUP screen.)

When you switch the surround mode, the following sur-

round channels will be assigned by default to each of the

MIX buses. (You are free to change these assignments

subsequently.)

Note

MIX buses shaded in gray in this table can be used as con-

ventional MIX buses. However in 6.1ch mode, the MIX 8/16

bus will operate only as FIXED type.

For example when the surround mode is 6.1ch and you

have chosen MIX 1–8 to use as the surround buses, the

surround pan signal flow will be as follows.

When a surround mode is selected, the MIX encoders allo-

cated to surround buses will operate differently than

normal. For example if MIX buses 1–8 are being used as

surround buses, you can use MIX encoders 1–8 of the MIX

section to edit the following parameters.

❏ If the MIX section [MIX SEND] key is on

A L ↔ R

Moves the surround pan of the selected channel

between left and right.

B F ↔ R

Moves the surround pan of the selected channel

between front and rear.

C Front divergence (5.1ch and 6.1ch modes

only)

Adjusts the front divergence (the proportion at which a

signal panned to the center will be sent to the front

center bus and to the front LR buses) of the selected

channel. Front divergence (the DIV F parameter) can

be adjusted if 6.1ch mode is being used.

D Rear divergence (6.1ch mode only)

Adjusts the rear divergence (the proportion at which a

signal panned to the rear will be sent to the rear center

bus and to the rear LR buses) of the selected channel.

E LFE (5.1ch and 6.1ch modes only)

Adjusts the send level of the signal sent from the

selected channel to the LFE (Low Frequency Effects)

bus.

Hint

• For details on each of the surround pan parameters, refer to

SURR PARAM screen (

➥

p.309) in the Reference section.

• If MIX buses 9–16 are being used as surround buses, you

can use MIX encoders 9–16 to perform the above

operations.

Surround

mode

MIX bus

3-1ch 5.1ch 6.1ch

MIX bus 1/9

(Front L)

MIX bus 2/10

(Front R)

MIX bus 3/11

(Center)

(Rear L)

MIX bus 4/12

(Surround)

(Rear R)

MIX bus 5/13

(Center)

MIX bus 6/14

LFE

(Subwoofer)

(Rear center)

MIX bus 7/15

LFE

(Subwoofer)

MIX bus 8/16

About the surround buses

Input channel 1

Input channel 2

How the MIX section will operate

1 2 3 4 5

18 Surround pan

144 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

❏ If the MIX section [MIX MASTER] key is on

A Output level

The encoders adjust the output level of each surround

channel.

Basic settings for surround buses

Here’s how to choose either 3-1ch, 5.1ch, or 6.1ch as the surround mode, and make settings for the MIX buses you will use as

surround buses.

According to the surround mode you intend to

use, connect an appropriate playback system

to MIX OUT jacks 1–8 or MIX OUT jacks 9–16.

In the DISPLAY ACCESS section, repeatedly

press the [MATRIX/ST] key to access the SURR

SETUP screen.

In order to use a surround mode, you will first choose

a surround mode, and then specify the MIX buses that

will be the surround output destinations.

Click a button in the SURROUND MODE area

to select the desired surround mode.

When you click a button a window will appear, asking

you to confirm that you want to switch the surround

mode.

Click the OK button to enable the surround mode you

selected. For example if you switch to 6.1ch mode, the

screen display will change as follows.

In the SURROUND BUS ALLOCATION area,

press the MIX 1-8 button or the MIX 9-16 but-

ton to select the MIX buses you want to use as

surround buses.

You can select either MIX buses 1–8 or MIX buses 9–

16. When you click a button a window will appear, ask-

ing you to confirm that you want to change the MIX

bus allocation.

When you click the OK button, the selected MIX buses

will be allocated as surround buses, and will be

assigned to surround channels according to the cur-

rent surround mode.

If you want to change the surround channel

assignments, click the / buttons at the left

and right of each field in the bus assign area,

and press the [ENTER] key (or click within the

box) to confirm the setting.

When the setting is confirmed, the previously-selected

bus and the newly-assigned bus will be exchanged.

Hint

You can initialize the surround channel assignments by click-

ing the INIT button located at the right of the bus assign area.

SURR SETUP

SURROUND MODE area

SURROUND BUS

ALLOCATION area

Bus assign area

SURR SETUP

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 145

Surround pan

Use the knobs and buttons in the lower part of

the screen to adjust the volume, delay, on/off

status, and cue for each surround channel.

For details on these knobs and buttons, refer to SURR

PARAM screen (➥ p.309) in the Reference section.

In the MIX section, make the [MIX MASTER]

key light, and turn on the MIX [ON] keys of all

MIX buses that will be used as surround buses.

The signal of each surround bus is now sent from the

corresponding MIX OUT jack.

Controlling surround pan

Here’s how to control surround pan for two adjacent input channels (or ST IN/FX RTN channels L and R).

Note

• Before you continue with the following procedure, you must

select the desired surround mode and connect MIX OUT

jacks 1–8 or MIX OUT jacks 9–16 to an appropriate play-

back system, as described in “Basic settings for surround

buses” (

➥

p.144).

• If you use 5.1ch or 6.1ch surround mode, connect the LFE

(Low Frequency Effects) channel signal to a dedicated sub-

woofer for the low frequencies. However, simply switching

the surround mode does not change the EQ (filter) settings.

As necessary, use the EQ (LPF) of the MIX channel

assigned to the LFE channel to cut the high-frequency por-

tion of the signal according to the frequency response of the

subwoofer you are using.

In the DISPLAY ACCESS section, repeatedly

press the [PAN/ROUTING] key to access the

SURR PARAM screen (PAN/ROUTING

function).

The SURR PARAM screen always shows surround pan

settings for two channels.

Use the channel selection area to select the

input channels whose surround pan settings

you want to edit.

Two adjacent odd-numbered/even-numbered chan-

nels (or ST IN/FX RTN channels L and R) will be

displayed.

Use the SURROUND BUS ON/OFF buttons

located around the surround pan grid to select

the surround buses to which the input chan-

nel will be sent.

The SURROUND BUS ON/OFF buttons are on/off

switches for the signal sent from the input channel to

each surround bus.

Hint

You can do the same thing by pressing a [SEL] key to select

an input channel, making the MIX section [MIX SEND] key

light, and then turning on the MIX [ON] key for the desired sur-

round buses.

Use any of the following methods to adjust the

surround pan of the selected channel.

• Using the mouse or track pad

Move the pointer into the surround pan grid of the

channel you want to control, and drag the yellow O

symbol forward/backward/left/right. (The symbol will

turn red while you are dragging it.) Alternatively, you

can click a desired location within the surround pan

grid to move the surround pan to that location.

• Using the pan buttons around the surround pan

area

If you want to quickly move the channel signal to the

location of a speaker, click one of the pan buttons (e.g.,

L, R, C) shown around the edge of the surround pan

grid.

• Using the CURSOR [√]/[®]/[π]/[†] keys

Move the cursor to the surround pan grid and press the

[ENTER] key; the O symbol will turn red.

In this condition, you can use the CURSOR [√]/[®]

keys to move surround pan left/right, or the CURSOR

[π]/[†] keys to move it forward/backward, in a range

of eight steps. By performing this operation while hold-

ing down the [SHIFT] key, you can quickly move

surround pan in a range of 32 steps. To finalize the sur-

round pan adjustment, press the [ENTER] key once

again.

SURR PARAM

Pan buttons SURROUND BUS

ON/OFF buttons

Channel selection

STEREO LINK button

Surround pan grid

18 Surround pan

146 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

• Using the MIX encoders

If you turn on the [MIX SEND] key of the MIX sec-

tion, you can use MIX encoders 1 or 9 to adjust the

left/right position of the input channel, and MIX

encoders 2 or 10 to adjust the front/rear position. The

SURR PARAM screen MIX SECTION ASSIGNMENT

area shows the parameters assigned to each MIX

encoder.

• Using MIDI control changes or GPI

If you assign surround pan parameters to MIDI con-

trol changes or GPI, you can use an external device to

control surround pan. For details, refer to MIDI CTRL

CHANGE screen (➥ p.191) and GPI screen (➥ p.194)

in the Reference section.

If you want surround pan operations to be

linked for two adjacent channels, turn on the

STEREO LINK button, and use the box at right

to select the link pattern.

When you turn on the STEREO LINK button, sur-

round pan will be linked for the two channels shown in

the SURR PARAM screen. To specify how they will be

linked, select one of the following link patterns by

clicking the / buttons at the left and right of the box

located to the right of the STEREO LINK button.

Edit other parameters as desired.

In the SURR PARAM screen you can also edit the fol-

lowing parameters.

• Divergence

These controls specify the proportion at which the sig-

nals are sent to each surround bus when the input

channel is positioned in the center. The parameters

that are displayed will depend on the surround mode

that is currently selected. (For details, refer to p.309)

•LFE

This adjusts the output level of the signal sent from the

input channel to the LFE (Low Frequency Effect) bus

for a subwoofer. You can also use the ON/OFF button

to switch the signal sent from the input channel to the

LFE bus on/off.

Hint

• The master level of each surround bus is shown in the upper

right of the screen.

• You can use the SURR VIEW screen to see the surround

pan settings of all channels at a glance.

Pattern 1

The channels will move in the same

direction for both the front/rear axis

and the left/right axis.

Pattern 2

The channels will move in opposite

directions for the front/rear axis, and in

the same direction for the left/right

axis.

Pattern 3

The channels will move in the same

direction for the front/rear axis, and in

opposite directions for the left/right

axis.

Pattern 4

Left↔right movement of the odd-num-

bered channel will be linked with

rear↔front movement of the even-

numbered channel. Front↔rear move-

ment of the odd-numbered channel

will be linked with left↔right move-

ment of the even-numbered channel.

Pattern 5

Left↔right movement of the odd-num-

bered channel will be linked with

front↔rear movement of the even-

numbered channel. Front↔rear move-

ment of the odd-numbered channel

will be linked with left↔right move-

ment of the even-numbered channel.

Pattern 6

Front/rear and left/right movement will

both be linked in the opposite direc-

tion.

Pattern 7

Left↔right movement of the odd-num-

bered channel will be linked with

front↔rear movement of the even-

numbered channel. Front↔rear move-

ment of the odd-numbered channel

will be linked with right↔left move-

ment of the even-numbered channel.

Pattern 8

Left↔right movement of the odd-num-

bered channel will be linked with

rear↔front movement of the even-

numbered channel. Front↔rear move-

ment of the odd-numbered channel

will be linked with left↔right move-

ment of the even-numbered channel.

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 147

Surround pan

Notes regarding surround pan

Here are some notes and limitations that you should be aware of when using surround pan.

❏ Scene recall operations

• The surround mode selection and the surround pan

settings of each channel are stored as part of the scene.

• If you recall a scene whose surround mode differs from

the current scene, the screen and panel display will

change accordingly. The surround mode is recalled

regardless of Selective Recall or Recall Safe settings.

• If one channel (of a pair of channels) is excluded from

recall, and you recall a scene in which the STEREO

LINK button is on, the STEREO LINK button will

remain on but only the other channel (of the pair) will

be recalled.

• SURROUND BUS SETUP settings (MIX bus 1-8/9-16

selection, and assignments to each surround channel)

are not included in the scene data.

❏ Channel library recall operations

• Surround pan related parameters for inputs are stored

in the input channel library.

• If the STEREO LINK button is on, and you recall input

channel library settings, the STEREO LINK button will

remain on, but only one channel will be recalled. Sub-

sequent operation will be according to STEREO LINK.

❏ Channel copy

• When you copy an input channel using panel opera-

tions, surround-related parameters will also be copied.

• In order to copy surround-related parameters using the

CH JOB screen (INPUT VIEW function), the ALL but-

ton must be turned on in the DESTINATION area.

❏ Global paste

• In order to paste surround-related parameters, the ALL

button must be turned on in the CURRENT SCENE

area of the GLOBAL PASTE screen (SCENE function).

In addition, the settings of the STEREO LINK area will

also be pasted if two adjacent channels are selected.

19 Other functions

148 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

This chapter explains other functionality of the PM5D not covered elsewhere.

Using the user deﬁned keys

You can assign the desired functions to the User Defined keys in the USER DEFINED section of the top panel, and press these

keys to execute the defined function.

A USER DEFINED [1]–[24] keys

B USER DEFINED [25] key

These are User Defined keys that execute the assigned

function.

Here’s how to assign the functions that will be executed

when the USER DEFINED [1]–[25] keys are pressed.

In the DISPLAY ACCESS section, press the

[UTILITY] key repeatedly to access the USER

DEFINE screen shown below.

In this screen you can make User Defined key assign-

ments for each of four banks; A–D.

In the BANK SELECT area at the upper left of

the screen, use the A–D buttons to select the

bank you want to use.

To clear the assignments of the current bank, click the

CLEAR BANK button located at the bottom of the

BANK SELECT area.

Click the button located on the line of the

User Defined key you want to assign.

The USER DEFINED KEY ASSIGN window will

appear. In this window you can select a function to

assign to the User Defined key, and select option

parameters.

Select the desired function in the FUNCTION

column, select parameters in the PARAMETER

1/2 columns, and click the OK button.

For details on the available functions and parameters,

refer to the Reference section (➥ p.208).

19 Other functions

Items in the USER DEFINED section

Assigning functions to the User

Deﬁned keys

USER DEFINE

BANK SELECT area

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 149

Other functions

Assign functions to other keys and banks in

the same way.

Hint

The User Defined key assignments are not saved in the

scene. If desired, you can save the assignments on a mem-

ory card as USER DEFINED KEY data.

Here’s how to use the USER DEFINED [1]–[25] keys to

execute the functions that have been assigned to them.

In the DISPLAY ACCESS section, repeatedly

press the [UTILITY] key to access the USER

DEFINE screen.

In the BANK SELECT area at the upper left of

the screen, use the A–D buttons to select the

bank (A–D) you want to use.

Press a USER DEFINED [1]–[25] key.

The function assigned to that key will be executed.

Using the FADER MODE section

In the FADER MODE section you can switch the channels that are assigned to DCA faders 1–8 of the panel DCA strip. For

each of six layers A–F, you can specify the channel that is assigned to each fader. For example, you might use this to simulta-

neously control the send level and return level of an internal effect, or to use a fader as the master fader of a MIX bus or

MATRIX bus.

In tandem with switching the FADER MODE section layer, you can also switch the machine being controlled by panel opera-

tions, the INPUT channel strip, the ST IN/FX RTN channel strip, and the STEREO A/B channel strip layer.

For each layer you can specify the channel/machine/layer that is assigned to each fader, and use the FADER MODE section to

switch between layers while you operate the faders.

In the FADER MODE section you can select the layers or

DCA groups that will be controlled.

A FADER MODE [A]–[F] keys

These switch the layer for DCA faders 1–8, the machine

affected by panel operations, the INPUT channel strip,

the ST IN/FX RTN channel strip, and STEREO A/B

channel strip.

B FADER MODE [DCA] key

If this button is on, DCA faders 1–8 will control DCA

groups 1–8.

Here’s how to assign the desired channel/machine/layer to

the FADER MODE section layers.

In the DISPLAY ACCESS section, repeatedly

press the [UTILITY] key to access the FADER

ASSIGN screen.

In this screen, you can select the desired channel/

machine/layer for each layer A–F.

Executing functions assigned to the

User Deﬁned keys

Items in the FADER MODE section

Assigning the FADER MODE section

layer

FADER ASSIGN

19 Other functions

150 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Use the channel selection boxes for the

desired layer (A–F) to select the channel

assigned to each fader 1–8.

To select a channel, move the cursor to the box and

turn the dial. The channel will blink; press the

[ENTER] key to confirm. You can choose from the fol-

lowing channels.

Hint

• If an input channel or a DCA fader 1–8 is selected, the chan-

nel name is displayed immediately below the channel

selection box.

• Input channels and output channels can coexist in the same

layer.

• Channels of each machine cascade-connected with the

DSP5D are assigned to the channels that show the corre-

sponding machine ID (#1–#3). Channels of the currently

selected machine are assigned to the channels for which a

machine ID is not shown. However, MONITOR and CUE are

fixed at PM5D (#1).

As desired, use the MACHINE ID

box corresponding to the layer (A–

F) you want to operate to select the

machine that will be controlled

from the panel.

To select a machine, move the cursor and

turn the [DATA] encoder and press the

[ENTER] key to confirm. The machines

that can be selected are “#1” (PM5D),

“#2” (DSP5D), “#3” (DSP5D), or

“STAY” (no change).

As desired, use the INPUT box and ST IN/FX

RTN box for the layer (A–F) you want to oper-

ate to select the INPUT channel strip and ST

IN/FX RTN channel strip layers.

To select a layer, move the cursor and turn the [DATA]

encoder and press the [ENTER] key to confirm.

As desired, change the assign-

ment of the STEREO A/B

channel strip (fader and [ON]

key).

To change the assignment, move the

cursor and turn the [DATA] encoder

and press the [ENTER] key to confirm. You can select

the following assignments.

• ST A/B

STEREO A/B channels

• MONITOR

Output level from the MONITOR OUT L/R/C jacks

• CUE

Output level from the MONITOR OUT L/R/C jacks

In the same way, assign the channel/machine/

layer for other layers.

Hint

The settings of the FADER MODE section are not saved in

the scene. If desired, you can save these settings on a mem-

ory card as DCA FADER MODE data.

In the FADER MODE section, use the FADER

MODE [A]–[F] keys to select the layer you want

to use.

The key LED will light, and the corresponding layer

will become active. If input channels are assigned to the

DCA faders, the channel names will appear in the

name indicators of the DCA strip.

Hint

You can also switch layers from within the FADER ASSIGN

screen. This screen also shows the values of the DCA faders

and their approximate positions.

Operate the faders of the DCA strip.

The level of the corresponding channels will change. If

a channel assigned to a DCA fader is paired (or if one

side of a stereo channel is assigned), the level of the

other paired channel (or the other side of the stereo

channel) will follow.

Note

If a FADER MODE [A]–[F] key is on, the DCA channel strip

[MUTE] keys can be used as [ON] keys of the corresponding

channels. The [CUE] keys can also be used as [CUE] keys for

the corresponding channels.

Item Selected channel

CH 1–CH 48 Input channel 1–48

STIN1L/STIN1R–STIN4L/

STIN4R

ST IN channel 1–4 L or R

FXRTN1L/FXRTN1R–

FXRTN4L/FXRTN4R

FX RTN channel 1–4 L or R

MIX 1–MIX 24 MIX channel 1–24

MTRX1–MTRX8 MATRIX channel 1–8

DCA1–8 DCA fader 1–8

MONITOR

Output level from the MONI-

TOR OUT L/R/C jacks

CUE

Output level from the CUE

OUT jacks

---- Fader disabled

STAY No change

Channel selection box

Switching the FADER MODE section

layer

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 151

Other functions

Locking the PM5D (Security functions)

The PM5D lets you prohibit changes to certain parameters (Parameter Lock), disabling file loading (Load Lock), or prohibit

operation of the console (Console Lock). For example, this lets you prevent an unauthorized person from operating the con-

sole while the engineer is taking a break.

You can also apply password protection to the lock function using a “system password” which is remembered even after

power-off, or a “console password” which is cleared when the power is turned off. You will be able to use Parameter Lock,

Load Lock, and Console Lock if you’ve specified a system password; you will only be able to use Console Lock if you’ve speci-

fied a console password.

Here’s how to set the password used for Parameter Lock

and Console Lock. However, it is possible to apply the lock

function even if a password has not been specified.

In the DISPLAY ACCESS section, repeatedly

press the [UTILITY] key to access the SECU-

RITY screen.

In this screen you can use the SYSTEM PASSWORD

and CONSOLE PASSWORD fields located at the left to

specify the passwords. (If no password has been speci-

fied, the corresponding box will indicate “--FREE--”.)

To set the system password, click the but-

ton for the SYSTEM PASSWORD field. To set

the console password, click the button for

the CONSOLE PASSWORD field.

A window will appear, and you will be asked to input

the new password. (The upper left of the window indi-

cates “NEW PASSWORD.”)

As an example, the illustration below shows the SYS-

TEM PASSWORD CHANGE window where you

specify the system password.

Note

• If a password has already been input, you will be requested

to input the old password. (The upper left of the window indi-

cates “OLD PASSWORD”.) In this case, input the existing

password and click the OK button before you continue to

step 3.

• If you want to return the system to a condition in which a

password has not been specified, input the existing pass-

word, click the OK button, and then leave the new password

field blank when you execute steps 3–5.

Use the character palette to input a password

of up to eight characters in the NEW PASS-

WORD text box.

The characters you input are displayed as “ * ”

(asterisks).

Any character of the character palette except for

SPACE can be used in a password. (The password is

case-sensitive; i.e., uppercase and lowercase alphabeti-

cal characters are distinguished.) When inputting a

password, the COPY, PASTE, SPACE, INS,

←, and →

keys of the character palette cannot be used.

Click the OK button.

The indication in the upper left of the window will

change to “RE-ENTER PASSWORD”.

Input the same password once again, and click

the OK button.

The password will be applied, and you will return to

the SECURITY screen.

Note

The console password will be cleared when the PM5D is pow-

ered-off. In contrast, the system password is remembered

even after the power is turned off. This means that if you for-

get the system password, you will be unable to defeat

Parameter Lock or Console Lock except by initializing the

entire memory of the PM5D (

➥

p.160). Please be careful not

to lose the system password.

Setting the System Password or Con-

sole Password

SECURITY

SYSTEM PASSWORD area

CONSOLE PASSWORD area

19 Other functions

152 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Here’s how to lock parameters or the console. You can also

lock using the password you specified.

In the DISPLAY ACCESS section, repeatedly

press the [UTILITY] key to access the SECU-

RITY screen.

If you want to lock

only specific parame-

ters, use the buttons

of the LOCK PARAME-

TER SELECT area to

select the parameters

for which you want to

prohibit editing.

When you click a button,

a check mark will appear

for the selected item. You

can select the following

items (multiple selections are allowed).

Note

• As long as the PARAMETER LOCK button is on, the above

settings cannot be edited. You will need to defeat the lock

function before editing them.

• If you turn on the RECALL LOCK button, the specified

parameters will also be unaffected by scene or library recall

operations.

Depending on the items you want to lock, click

either the PARAMETER LOCK button, LOAD

LOCK button or CONSOLE LOCK button.

If a password has been specified, a window will ask you

to input the password. If you click the CANCEL but-

ton without inputting a password in this window, you

will return to the previous screen.

Note

If the LOAD LOCK button is on, synchronization can occur

only from this unit to PM5D Editor/DSP5D Editor (not the

reverse) when synchronizing with PM5D Editor/DSP5D Editor.

Input the password you assigned beforehand,

and click the OK button.

If you clicked the PARAMETER LOCK button in step

3, a message of “Parameter Locked” will appear briefly,

and then editing will be disabled for the selected

parameters.

If you clicked the CONSOLE LOCK button in step 3,

an indication of “CONSOLE LOCKED” will appear on

the screen, and all operations other than pressing the

UNLOCK button will be disabled.

To defeat Parameter Lock, click the PARAME-

TER LOCK button. To defeat Console Lock,

click the UNLOCK button.

If a password has been specified, a window will ask you

to input the password. Input the password and click

the OK button to defeat the lock function. You will

return to the screen in which you were prior to apply-

ing the security setting.

Note

The console password will be cleared when the PM5D is pow-

ered-off. In contrast, the system password is remembered

even after the power is turned off. This means that if you for-

get the system password, you will be unable to defeat

Parameter Lock or Console Lock except by initializing the

entire memory of the PM5D (

➥

p.160). Please be careful not

to lose the system password.

Item Content

SYSTEM CONFIG-

URATION

Changes to the settings of the MIXER

SETUP screen and CASCADE screen

WORD CLOCK

SETUP

Changes to the word clock setting

DITHER Changes to dither-related settings

INPUT PATCH

Changes to the input patch settings

(and names)

OUTPUT PATCH Changes to the output patch settings

INPUT CH ON/OFF Input channel on/off operations

OUTPUT CH ON/

OFF

Output channel on/off operations

MIX TO ST ON/OFF

MIX TO STEREO button on/off opera-

tions

DCA MUTE ON

DCA [MUTE] key On operations

(Off operations are not included)

Using Parameter Lock or Console Lock

SECURITY

LOCK PARAMETER SELECT area

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 153

Other functions

Using cascade connections

You can share buses by cascade-connecting a PM5D and DSP5D, multiple PM5D units (maximum of four units), or a PM5D

with an external mixer (Yamaha DM2000/02R96, etc.). When multiple PM5D/DSP5D units are cascade-connected, opera-

tions such as scene store/recall, cue/solo, and dimmer can also be linked.

Up to two DSP5D units can be cascade-connected to one

PM5D unit. By going through a DCU5D digital cabling

unit, you can also utilize long-distance routing via Ether-

net cable. For details, refer to p.31.

Here we will explain cascade connections and operation,

using an example in which two PM5D units are cascade-

connected.

To cascade-connect two PM5D units, connect the CAS-

CADE IN connectors and CASCADE OUT connectors of

the two units to each other. This allows the MIX bus, STE-

REO bus, and CUE bus output signals to be transmitted

and received between the two units.

If you want operations such as scene store/recall and cue/

solo to be linked between the two PM5D units, specify one

unit as the cascade master and the other as the cascade

slave. (This setting is made in the SYS/W.CLOCK function

MIXER SETUP screen.) The PM5D assigned as the cas-

cade master will output control signals (operational

signals) via its CASCADE IN connector, and the PM5D

assigned as the cascade slave will receive these signals via its

CASCADE OUT connector.

Hint

• If you want to daisy-chain two to four PM5D units (i.e., con-

nect the first unit’s CASCADE OUT

→

second unit’s

CASCADE IN, and the second unit’s CASCADE OUT

→

third unit’s CASCADE IN. Up to four units can be con-

nected.), you should assign the PM5D located last in the

chain (the PM5D connected only via its CASCADE IN con-

nector) as the cascade master, and the remaining PM5D

units as cascade slaves (

➥

p.226).

• If you want to cascade-connect a PM5D with a Yamaha

DM2000 or 02R96, connect the CASCADE OUT connector

of the DM2000/02R96 to the CASCADE IN connector of the

PM5D. However in this case, it is not possible to link

operations.

• If you want to cascade-connect the PM5D with any other

external mixer, use I/O cards installed in slots 1–4 to send

and receive the audio signals (

➥

p.224).

When cascade-connecting the PM5D and DSP5D, you

must specify a unique ID number for each machine

(PM5D and DSP5D). Specify the machine ID number as

#1 (PM5D), #2 (first DSP5D unit), and #3 (second DSP5D

unit).

Note

• The PM5D’s machine ID number is fixed at #1, so you don’t

need to set it.

• For a system in which only DSP5Ds are connected in cas-

cade, set the machine ID number of the first DSP5D to #1,

and set the second DSP5D to #2.

❏ Making settings on the DSP5D itself

Power-on the DSP5D, and press the mode

switch located on the rear panel.

Between one and three of the front panel IN/

OUT [TX]/[RX] LEDs will light, corresponding

to the machine ID number (1–3).

One LED (OUT [TX]) is lit to indicate machine #1 (a

system consisting of only the DSP5D), two LEDs (OUT

[TX]/[RX]) are lit to indicate machine #2 (the first

DSP5D unit), and three LEDs (OUT [TX][RX]

IN[TX]) are lit to indicate machine #3 (the second

DSP5D unit) is selected.

Example of cascade connections

between the PM5D and DSP5D

Stage

FoH

DSP5D DSP5D

DCU5D

POWER

CASCADE

OUT

CASCADE IN CASCADE IN

Ethernet CAT5

Ethernet

CAT5

OUT

PM5D

Example of cascade connections

between PM5D units

PM5D A

CASCADE

OUT

CASCADE

OUT

PM5D B

Audio

signals of

units A+B

Audio

signals of

units A+B

(cascade master) (cascade slave)

Specifying the DSP5D’s machine ID

number

FAN

HIGH LOW

POWER

FAN

HIGH LOW

POWER

Mode switch

19 Other functions

154 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

• For machine ID #1

• For machine ID #2

• For machine ID #3

While the machine ID number LEDs are lit

(within five seconds), you can repeatedly press

the mode switch to cycle through machine ID

#1 → #2 → #3 → #1 → #2 → #3.

Note

The machine ID number LED indication will return to the nor-

mal display when you have not pressed the mode switch for

five seconds or more.

❏ Making settings from DSP5D Editor

Synchronize DSP5D Editor with the DSP5D

itself.

In the Mixer Setup window, use Cascade Con-

nection to specify the machine ID number.

Note

For details, refer to the DSP5D Editor Owner’s Manual.

Here we will explain the basic settings needed when cas-

cade-connecting the PM5D and DSP5D, and when

cascade-connecting two PM5D units bi-directionally.

❏ Cascade-connecting the PM5D and

DSP5D

In the DISPLAY ACCESS section, repeatedly

press the [SYS/W.CLOCK] key until the MIXER

SETUP screen appears.

In the CASCADE CONNECTION area located at

the bottom of the screen, click the TYPE

SELECT button to access the CASCADE TYPE

SELECT window.

According to the DSP5D or DCU5D that is con-

nected, select the appropriate connection

type, and click the OK button to close the

window.

According to the type you selected, a connection dia-

gram is shown in the CASCADE CONNECTION field,

and cascade settings such as ports will be made

automatically.

Hint

For details on each connection type, refer to p.223.

OUT

TX RX TX RX

OUT

TX RX TX RX

OUT

TX RX TX RX

Basic settings for cascade connection

MIXER SETUP

CASCADE CONNECTION areaTYPE SELECT

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 155

Other functions

❏ Cascade master (bi-directional cascade

connections between PM5D units)

In the DISPLAY ACCESS section, repeatedly

press the [SYS/W.CLOCK] key until the MIXER

SETUP screen appears.

In the CASCADE CONNECTION area located at

the bottom of the screen, click the TYPE

SELECT button to access the CASCADE TYPE

SELECT window.

Select “PM5D - PM5D” as the connection type,

and click the OK button to close the window.

In the CASCADE MODE area at the lower part

of the screen, select “MASTER”. In addition,

turn on the BI-DIRECTION button located

immediately below it.

When multiple PM5D units are cascaded, the settings

of the CASCADE MODE area specify whether the unit

will operate as a cascade master (when “MASTER” is

selected) or as a cascade slave (when “SLAVE” is

selected).

If you turn the BI-DIRECTION button on, the mixed

audio signals of both cascade-connected PM5D units

will be output from both units.

Select “PM5D” in the CASCADE FROM field

and in the CASCADE TO field.

In the CASCADE FROM field, select one of the follow-

ing as the type of the external device that is sending

signals to the PM5D via the cascade connection.

In the CASCADE TO field, select either “PM5D” or “--

--” (transmission disabled) as the external device to

which the signal will be sent from the PM5D via the

cascade connection.

Make sure that “CASCADE IN” is selected for

the CASCADE IN PORT SELECT field, and “CAS-

CADE OUT” is selected for the CASCADE OUT

PORT SOURCE SELECT field.

The CASCADE IN PORT SELECT and CASCADE

OUT PORT SOURCE SELECT fields select the ports

MIXER SETUP

CASCADE CONNECTION area

CASCADE MODE area BI-DIRECTION button

Display

Source

device

Selectable cas-

cade input port

Parameter

linkage

—

Cascade dis-

abled

CASCADE IN,

SLOT 4, SLOT 3/4,

SLOT1-4 [CH1-8],

SLOT 1-4 [CH9-16]

Not

possible

PM5D another PM5D CASCADE IN Possible

*1. Linked parameters are speciﬁed in the CASCADE

screen.

DM2000

/02R96

Yamaha

DM2000 or

02R96

CASCADE IN

Not

possible

MIXER

[30BUS]

A mixer other

than the above

(maximum 30

bus)

SLOT 3/4,

SLOT 1-4 [CH1-8],

SLOT 1-4 [CH9-16]

MIXER

[16BUS]

A mixer other

than the above

(maximum 16

bus)

SLOT 4

CASCADE FROM

ﬁeld

CASCADE TO ﬁeld

CASCADE IN PORT

SELECT ﬁeld

CASCADE OUT PORT

SOURCE SELECT ﬁeld

19 Other functions

156 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

through which audio signals will be transmitted to and

received from the cascade-connected external device.

If “PM5D” or “DM2000/02R96” are selected as the

other cascade-connected device, only “CASCADE IN”

can be selected for the CASCADE IN PORT SELECT

field. In the CASCADE OUT PORT SOURCE SELECT

field, you can choose from the output channels of slots

1–4 as well as “CASCADE OUT” (➥ p.225).

Hint

If you choose a setting other than “CASCADE OUT” in the

CASCADE OUT PORT SOURCE SELECT field, the same

signal will be output from both the specified slot/channel and

from the CASCADE OUT connector.

❏ Cascade slave (bi-directional cascade

connections between PM5D units)

In the DISPLAY ACCESS section, repeatedly

press the [SYS/W.CLOCK] key to access the

MIXER SETUP screen.

In the CASCADE CONNECTION area located at

the bottom of the screen, click the TYPE

SELECT button to access the CASCADE TYPE

SELECT window.

Select “PM5D - PM5D” as the connection type,

and click the OK button to close the window.

In the CASCADE MODE area at the lower part

of the screen, select “SLAVE”. In addition, turn

on the BI-DIRECTION button located immedi-

ately below it.

Select “PM5D” in the CASCADE FROM field

and in the CASCADE TO field.

Make sure that “CASCADE IN” is selected in

the CASCADE IN PORT SELECT field, and “CAS-

CADE OUT” is selected in the CASCADE OUT

PORT SOURCE SELECT field.

Here we will explain how to select the buses used for the

cascade connection, specify the items that will be linked,

and enable the cascade connection. Perform the following

steps on both the cascade master and cascade slave units.

In the DISPLAY ACCESS section, repeatedly

press the [SYS/W.CLOCK] key until the CAS-

CADE screen shown below appears.

In this combination you can enable/disable buses used

for transmission/reception in the cascade connection,

and select the operations that will be linked when mul-

tiple PM5D units are cascade-connected.

Note

In the case of a system that is cascade-connected to the

DSP5D, the system will always operate as though the CAS-

CADE LINK area’s LINK button is on; this setting cannot be

changed.

In the CASCADE LINK area at the left of the

screen, turn on the buttons for the operations

that you want to be linked.

The settings of the CASCADE LINK area select the

operations that will be linked when multiple PM5D

units are cascade-connected. You can select the follow-

ing items.

• SCENE RECALL

Scene recall operations / Recall undo operations

Selecting the buses used for cascade

connection

CASCADE

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 157

Other functions

• SCENE STORE/EDIT

Scene store operations, store undo operations, title

editing, sorting

• CUE/SOLO LOGIC

Cue/Solo operations

• DIMMER ON/OFF

Dimmer effect (including talkback dimmer)

• PAGE CHANGE

Switching the display screen

• DCA FADER MODE

Switching the mode of the top panel FADER MODE

section

• ENCODER MODE

Switching the mode of the top panel ENCODER

MODE section

• PANEL/LCD BRIGHTNESS

BRIGHTNESS settings in the PREFERENCE 2 screen

(UTILITY function)

• INPUT METER POINT/OUTPUT METER POINT/

PEAK HOLD

Input channel / output channel metering point selec-

tion, and peak hold on/off

• DCA LEVEL/MUTE

DCA group 1–8 level, name, [CUE] key on/off opera-

tions, and [MUTE] key on/off operations

• MUTE MASTER

Mute group 1–8 on/off

Note

• Note that linking is enabled only if the LINK buttons for the

same item are turned on for both the cascade master unit

and the cascade slave unit.

• If you have cascade-connected three or more PM5D units in

a daisy-chain, you can also turn linking off for the cascade

master but on between the cascade slaves.

Hint

DCA and MUTE parameter values will be linked as soon as

linking is turned on. CUE/SOLO will be initialized as soon as

linking is turned on. Other parameters will be linked only when

that parameter is first operated after Link is turned on.

In the CASCADE I/O ASSIGN VIEW area, use

the CASCADE IN and CASCADE OUT ON/OFF

buttons to specify whether each bus will trans-

mit or receive audio signals to or from the

external cascade-connected device.

The CASCADE IN and CASCADE OUT ON/OFF but-

tons specify whether signals of each bus will be

transmitted to or received from the cascade-connected

external device. These settings are made independently

for each bus; MIX buses 1–24, STEREO A bus L/R,

STEREO B bus L/R, and CUE bus L/R.

Buses whose CASCADE IN button is on will receive

signals from the external device; buses whose CAS-

CADE OUT button is on will send signals to the

external device.

The CASCADE IN SOURCE fields indicate each of the

source buses. If the other cascade-connected device is a

PM5D or DSP5D, these assignments are fixed and can-

not be modified.

Note

• When two PM5D units are cascade-connected, signal trans-

mission and reception is enabled if the CASCADE OUT

button of the transmitting unit and the CASCADE IN button

of the receiving unit are both turned on for the same bus.

• If a device other than the PM5D/DSP5D is selected as the

other cascade-connected device, the transmission source

indication shown in the CASCADE IN SOURCE field will

change (

➥

p.227).

Using the PARAM LINK ON/OFF button

located in the CASCADE I/O ASSIGN VIEW

area, specify whether channel parameters will

be linked between machines.

You can specify this for every two adjacent odd-num-

bered/even-numbered channels. Turn this on if you

want each machine to output the same signal.

Set the CASCADE ENABLED/DISABLED button

to ENABLED.

When you click the DISABLED button, it may take up

to 10 minutes for cascade connection to be enabled.

The cascade connection will be enabled when the CAS-

CADE ENABLED/DISABLED button is set to

ENABLED on both the cascade master and the cascade

slave.

Note

If the word clock becomes unlocked while the machines are

synchronized (before cascade connection is enabled), the

operation of each machine may become unstable. If this

occurs, please power-cycle each machine.

CASCADE IN SOURCE area

CASCADE IN ON/OFF buttons

PARAM LINK buttons

CASCADE OUT ON/OFF buttons

19 Other functions

158 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Connecting the PM5D to your computer via USB

The PM5D Editor application can be installed in a computer and used to control the PM5D’s parameters or to backup and

restore the contents of the PM5D’s memory.

Here we will explain the operations required in order to establish a USB connection between the PM5D and a computer.

Note

The following procedure assumes that the PM5D Editor pro-

gram and USB-MIDI driver have already been correctly

installed in the computer. Before you continue, download the

program and driver from the Yamaha website and install them.

http://www.yamahaproaudio.com/

In the DISPLAY ACCESS section, repeatedly

press the [MIDI/REMOTE] key until the MIDI

SETUP screen appears.

In the PM5D EDITOR area at the lower right of

the screen, select the port to which the com-

puter is connected, and select the PM5D’s ID

number.

First use the PORT field to select the port that will be

used to communicate with the computer. Click the /

buttons located at the left and right of the left box to

select the type of port, and press the [ENTER] key (or

click inside the box) to finalize your selection. If you

select USB or SLOT 1–4, use the box at the right to

select a port number 1–8.

Next, use the ID field to select an ID number in the

range of 1–8 for the PM5D that you want to control.

(This number is used to distinguish individual PM5D

units when multiple units are being used together.)

Note

Set the USB port number and PM5D ID number to match the

settings in the PM5D Editor. For details, refer to the PM5D

Editor owner’s manual.

Start up PM5D Editor on the computer, and

use a USB cable to connect the computer to

the PM5D.

This enables communication between the computer

and the PM5D. For details on operation, refer to the

PM5D Editor owner’s manual.

Note

• If you disconnect or reconnect the USB cable, or power-

cycle the PM5D, you must close the PM5D Editor and shut

down the computer. In some cases, it may not be possible to

reconnect with the PM5D until the computer is restarted.

• Use a USB cable no longer than 3 meters. Also, connect the

PM5D directly to the USB connector of the computer; do not

use a USB hub.

You must observe the following points when connecting

the PM5D to your computer via the USB TO HOST con-

nector. If you fail to observe these points, your computer

or the PM5D may stop operating (“hang up”), causing

data to be corrupted or lost. If the computer or the PM5D

stops working, turn the power off and then on again, and

restart the computer.

• Before connecting the computer via the USB TO

HOST connector, disable the power management

mode (suspend/sleep/standby/hibernate) on your

computer.

• Connect the USB TO HOST connector to the com-

puter before you power-on the PM5D.

• Close all application programs (such as PM5D Edi-

tor) before turning the PM5D’s power on or off, or

connecting or disconnecting the USB cable.

• Leave an interval of at least three seconds between

powering the PM5D on and off, or between discon-

necting and connecting the USB cable.

MIDI SETUP

PM5D EDITOR area

Caution when using the USB TO

HOST connector

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 159

Other functions

Connecting the DSP5D to your computer via Ethernet

You can use the DSP5D Editor program installed in your computer to control the DSP5D’s parameters and to back up and

restore the contents of its memory.

Here we will explain the necessary steps for using an Ethernet cable to connect the DSP5D to your computer.

Note

• The following steps assume that the DSP5D Editor program

and DME-N Network driver have been correctly installed in

your computer. Before you continue, download the program

and driver from the Yamaha website and install them.

http://www.yamahaproaudio.com/

• For details on settings when using the DSP5D by itself, refer

to the DSP5D Editor Owner’s Manual. If you do not know the

network settings, you can initialize the internal memory

(

➥

p.160) to return the settings to the default values listed in

step 3.

In the DISPLAY ACCESS section, repeatedly

press the [UTILITY] key to access the PREFER-

ENCE 2 screen.

In the NETWORK area at the lower right of the

screen, click the SET button to access the NET-

WORK window.

A IP ADDRESS

This specifies the number (IP address) that is assigned

in order to distinguish individual devices within the

Internet or LAN (Local Area Network). Set this so that

it does not conflict with other devices on the network.

B GATEWAY ADDRESS

This specifies a number (gateway address) that distin-

guishes devices (gateways) that convert data between

different media or protocols to allow communication

within the network. Set this so that it does not conflict

with the IP address of other devices on the network.

C SUBNET MASK

Within the IP address used in the network, this defines

the bits that are used for the network address that dis-

tinguishes the network.

Specify the IP address, gateway address, and

subnet mask by clicking the / buttons

located at the left and right of each box.

If you’re connecting the DSP5D and your computer in

a one-to-one connection, we recommend that you use

the following default values.

• IP address

192.168.0.129

• Gateway address

192.168.0.1

• Subnet mask

255.255.255.0

Click OK to close the NETWORK window.

Make network settings on your computer.

For the case of the example shown above, set the IP

address in the range 192.168.0.2–127, and set the gate-

way address and subnet mask to the same value as the

DSP5D.

Use an Ethernet cable to connect the com-

puter and the DSP5D, and start up DSP5D

Editor on your computer.

This will allow communication between your com-

puter and the DSP5D. For specific operating

procedures, refer to the DSP5D Editor Owner’s

Manual.

PREFERENCE 2

SET button

19 Other functions

160 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

Initializing the PM5D’s internal memory

If an error occurs in the PM5D’s internal memory, or if you are unable to return to normal operation because you have for-

gotten the system password, use the following procedure to initialize the internal memory.

When you initialize the internal memory, the content that had

been previously been saved in memory (including read-only

scene memories) will be lost. You must use extreme caution

when performing this operation.

While holding down the SCENE MEMORY

[STORE] key of the panel, turn on the power of

the PW800W power supply.

After the opening screen, the following initialization

menu screen will appear.

Click one of the following buttons to select the

desired type of initialization.

• INITIALIZE ALL MEMORIES

All memories including scene memories and libraries

will return to their factory-set condition.

• INITIALIZE CURRENT MEMORIES

Memories other than scene memories and libraries will

return to their factory-set condition.

• CANCEL

The initialization procedure will be aborted, and the

PM5D will start up in normal operating mode.

Note

If the voltage of the backup battery runs low, or if an error

occurs in the internal memory, a warning message will appear

at the bottom of the screen, and the initialization menu will

appear “by force.” Please note that if the warning message is

displayed, and you click the CANCEL button to start in normal

operating mode, we cannot guarantee that the system will

operate correctly.

A message will ask you to confirm that you

really want to initialize; click the OK button.

When the internal memory has been initialized, the

PM5D will start up in normal operating mode.

Initializing the DSP5D’s internal memory

If an error occurs in the DSP5D’s internal memory, or if

you are unable to connect from your computer because

you’ve forgotten the network settings, you can use the fol-

lowing procedure to initialize all of the DSP5D’s memory

(including scene memories, libraries, and network set-

tings) to the factory-set condition.

When you initialize the internal memory, the content that had

been previously been saved in memory (including read-only

scene memories) will be lost. You must use extreme caution

when performing this operation.

While holding down the rear panel Mode

switch, turn on the power.

The four front panel IN/OUT [TX]/[RX] LEDs will light.

When the four LEDs light, release the Mode

switch, and then press and hold the Mode

switch once again for about five seconds.

The four LEDs will return to their normal lit state.

After the LEDs return to their normal lit state,

release the Mode switch and wait for about

twenty (20) seconds to three (3) minutes.

The four LEDs will light up consecutively starting from

the left.

Verify that the OUT [TX] LED at left is blinking

and that the other three LEDs light up steadily.

Turn the power off, and then on again.

The entire contents of memory (including the scene

memories, libraries, and network settings) were reset to

the factory state in step 4, but you must be sure to

power-cycle the unit in order to return it to normal

operation.

FAN

HIGH LOW

POWER

FAN

HIGH LOW

POWER

Mode switch

CASCADE IN

OUT OUT

OUT

TX RX TX RX

ININ

75Ω

TERMINATED

OUT OUT

OUT

TX RX TX RX

ININ

75Ω

TERMINATED

IN/OUT [TX]/[RX] LEDs

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section 161

Other functions

Adjusting the faders and input/output gain (Calibration)

Depending on the conditions of use, discrepancies may occur in the behavior of the motor faders. you can use the Calibration

function to correct such discrepancies. If necessary, you can also make fine adjustments to the analog input/output gain.

While holding down the [ENTER] key of the

panel, turn on the power of the PW800W

power supply.

After the opening screen, the following calibration

menu screen will appear.

Click one of the following buttons to choose

what you want to calibrate.

A window for the calibration item you selected will

appear.

Make calibration settings as directed by the

instructions that appear in the window.

Click the OK button in the window.

The calibration settings will be applied, and the PM5D

will start up in normal mode.

Here you can execute a semi-automatic procedure for cali-

brating the faders of the specified channel strip (INPUT,

DCA, STEREO A/B, ST IN/FX RTN). This window will

also appear if a problem with the fader settings is detected

when the PM5D is started up.

Click a fader select button to add a check mark

to the faders you want to calibrate.

If problems with certain faders were detected during

start-up, those buttons will be on (green), and check

marks will already be shown for them.

Click the START CALIBRATION button; calibra-

tion will begin automatically.

A progress bar will indicate the state of the process.

The automatic processing will end when the

progress bar reaches 60%. Manually move all

faders you specified for calibration to the posi-

tions listed below in the following order:

1 –∞

2 –20 dB

3 0 dB

4 +10 dB

After you have set the faders to the correct

position, press the [ENTER] key.

Processing will proceed to the next fader position.

Repeat steps 3–4 for each fader position 1–4.

Verify that calibration has been completed and

that all fader select buttons are now off. Then

click the OK button.

The calibration settings will be stored in internal mem-

ory. If a fader select button remains on (green),

calibration has failed. Try executing calibration once

again.

Note

The progress bar will indicate “Writing...” while the settings are

being written to internal memory; do not turn off the power

while this indication is visible.

CALIBRATE FADER

POSITION

The FADER CALIBRATION win-

dow will appear, allowing you to

calibrate the speciﬁed faders.

CALIBRATE AD INPUT

GAIN (make ﬁne adjust-

ments to the analog

input gain; PM5D-RH

model only)

The AD INPUT TRIM window

will appear, allowing you to

make ﬁne adjustments to the

gain of the speciﬁed analog

input port.

CALIBRATE OUTPUT

GAIN (make ﬁne adjust-

ments to the output

ports)

The OUTPUT TRIM window will

appear, allowing you to make

ﬁne adjustments to the gain of

the speciﬁed output port.

Calibrating the faders

19 Other functions

162 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Operating section

If necessary, you can make fine adjustments in steps of

0.1 dB to the gain of the specified analog input port. Since

the input levels of all ports are set to match each other

when the PM5D is shipped from the factory, you will nor-

mally not need to change these settings.

Note

• Since these are set to optimal values at the factory, the

default values will differ between input ports. Initializing the

internal memory will return these settings to their factory-set

values.

• Fine adjustments of the DSP5D’s input/output gain should

be made from DSP5D Editor.

To adjust the gain, click the / buttons located at the

left and right of each box to specify the gain of each input

port in 0.1 dB units. If you want to restore all input ports

to their factory settings, click the FACTORY PRESET but-

ton. Click the OK button to apply the settings.

If necessary, you can make fine adjustments in steps of 0.01

dB to the gain of the specified output port. The factory set-

ting is 0.00 dB.

To adjust the gain, click the / buttons located at the

left and right of each box to specify the gain of each output

port in 0.01 dB units. If you want to reset all output ports

to 0.00 dB, click the FACTORY PRESET button. Click the

OK button to apply the settings.

Adjusting the analog input gain

(PM5D-RH model only)

Adjusting the output gain

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 163

Reference section

The Reference section explains the functionality and operations for every screen of the PM5D,

organized into four main areas; function menu, global functions, output functions, and input

functions.

The following illustration is a typical screen on the PM5D.

This screen shows the following information.

Upper part of the display

(always visible)

A Function Name Indication

Displays the name of the function currently selected in

the screen. By clicking the BACK/FORWARD buttons

you can move through the eight most recent screens

that were displayed for at least two seconds (with the

exception of function menus). You can also access the

Function menu by clicking this function name indica-

tion. When the Function menu is displayed, click once

again to return to the previously-displayed screen.

B SCENE MEMORY

Indicates the number and title of the last-stored or

recalled scene memory. If you select a different scene,

the number and title will blink. If you edit the contents

of a scene after storing it, the EDIT indicator in the

upper right will light. If the scene is write-protected, a

lock icon is displayed at the right of the title, and read-

only scenes are indicated as “R.”

Note

• You can move the cursor to the scene number and turn the

[DATA] encoder to select a scene.

• If you click here while the number and title are blinking, the

most recently stored or recalled scene will be displayed.

C NEXT SCENE/NEXT EVENT

Indicates the scene/event that will be recalled next by

the User Defined keys or the Event List function. The

information shown here will differ as follows, depend-

ing on the settings in the EVENT LIST screen of the

SCENE function.

• If the DISABLE button is turned on in the EVENT

LIST screen

Indicates the number and name of the next scene (the

scene that will be recalled when you press a User

Defined key assigned to the “INC RECALL” function).

Normally, this will be the scene of the number follow-

ing the most recently recalled or stored scene.

• If the ENABLE [ALL MANUAL] button or the

[ENABLE] button is turned on in the EVENT LIST

screen

Indicates the number and name of the next event (the

scene that will be recalled next by the Event List func-

tion). At the right is displayed the time until the next

event will be recalled (or the condition upon which the

event will be recalled).

Note

• The “MANUAL” indication means that the user must exe-

cute the Next Event operation in order to recall the next

event. (Press a User Defined key assigned to the “NEXT

EVENT RECALL” function, or click the NEXT button in the

EVENT LIST screen.)

• If a time is displayed, this indicates the remaining time until

the next event is recalled automatically.

• The “--------” indication means that there is no event to be

recalled next.

D PRESENT TIME, TIME CODE, CASCADE/Fs

Click this area to cycle through the following three

items of information. This is linked with the UPPER

PART DISPLAY setting in the PREFERENCE 2 screen

(UTILITY function).

Information shown in the display

6 7 8 9 J K

4 5

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

Main area of the display

164 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

• PRESENT TIME

Indicates the present time. The time can be specified in

the UTILITY function PREFERENCE 1 screen.

• TIME CODE

Indicates the internal time code being generated by the

PM5D (machine #1), or the time code being received

from an external device. This is the same as the time

code shown in the SCENE function EVENT LIST

screen.

• CASCADE/Fs

Indicates the master/slave status when using a cascade

connection, and the sampling frequency at which the

PM5D system is currently operating.

E METER SECTION

Indicates the type of channels that are currently shown

by the meters in the upper left and right of the panel.

You can also click the / buttons to switch this

directly.

F EVENT indicator

The EVENT indicator is displayed here if the ENABLE

[ALL MANUAL] or ENABLE button is turned on in

the SCENE function EVENT LIST screen.

G FADING/TRACKING indicator

This area shows the FADING indicator while fade time

is being executed, or the TRACKING indicator if

Tracking Recall is available. If both are enabled, FAD-

ING takes priority.

H LCR/LCR [B] indicator

If there is at least one channel for which LCR is turned

on, the LCR indicator is displayed here.

If in the SYS/W.CLOCK function MIXER SETUP

screen the BUS SETUP setting STEREO B is set to USE

AS CENTER BUS, the LCR [B] indicator is displayed

here.

I TB/OSC/DIMM indicator

If talkback, oscillator, or dimmer are on, the respective

TB/OSC/DIMM indicator is displayed here. If more

than one of these are enabled, the display priority is

TB>OSC>DIMM.

J SOLO/INPUT CUE/DCA CUE/OUTPUT CUE/

KEY IN CUE/EFFECT CUE/EXTERNAL CUE

indicator

If Solo or Cue Monitor is enabled, the corresponding

indicator is shown here. If more than one Cue is

selected, only the indicator for the currently-valid Cue

is shown.

K BUSY/RS422/HA/GPI/MIDI indicator

The BUSY indicator is shown here while internal mem-

ory or a PC card in the card slot is being accessed.

When RS422/HA/GPI/MIDI signals are received (in

the case of RS422, when Status is received to indicate a

status change on a connected device), the appropriate

indicator will appear briefly. If more than one of these

conditions occur simultaneously, the display priority is

BUSY>RS422>HA>GPI>MIDI.

Note

In the case of MIDI signals, the indicator will light if signals are

received at the MIDI connector, USB connector, or slots 1–4.

However, active sensing, MIDI clock, and quarter time code

messages will not cause the indicator to light.

Main area of the display

A Tabs

Click this area to switch between screens within the

selected function.

B Function parameters

This area shows parameters for the currently selected

function or screen.

Lower part of the display

(always visible)

A SELECTED CH (Selected channel)

Indicates the type and name of the channel currently

selected by the [SEL] key. You can also move the cur-

sor and turn the [DATA] encoder to change this

directly.

B MACHINE ID

If the DSP5 is cascade-connected, this indicates the

machine (PM5D or DSP5D) #1–#3 that is being con-

trolled from the panel. You can also move the cursor

and turn the [DATA] encoder to change this directly.

When you switch machines, the screen background

color and the constantly displayed screen (except for

time code) will also change to the settings of the

machine that is now being controlled. The screen back-

ground color can be specified for each machine in the

UTILITY function PREFERENCE 2 screen. The indica-

tor above will light only for the machine ID number

that is cascade-connected.

C MIX SECTION

Indicates the encoder mode currently selected in the

MIX section. In MIX SEND mode this indicates

“SEND,” in MIX MASTER mode this indicates “MAS-

TER,” and if a shortcut operation has been used to

select TO MATRIX mode this indicates “TO

MATRIX.” You can also move the cursor and turn the

5 6 7 9

1 32 4

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 165

[DATA] encoder to directly switch between “SEND”

and “MASTER.”

D Encoder/Fader mode

Indicates the parameters that are assigned to the

encoders/faders of the input channel strip.

The encoders can be assigned to MIX SEND 1–24,

GAIN, ATT, PAN/BAL, LEVEL, or REMOTE. The fad-

ers can be assigned to LEVEL, MIX SEND 1–24, or

REMOTE. For both the encoders and the faders, for

parameters other than REMOTE, you can move the

cursor and turn the [DATA] encoder to switch them

directly.

If you select LEVEL for the encoders, the faders will be

flipped; the most recently selected of the MIX SEND 1–

24 parameters will be assigned to the faders. Similarly,

the faders will also be flipped if you select MIX SEND

1–24 for the faders; the LEVEL parameter will be

assigned to the encoders.

E INPUT CH (Input channel) layer

This shows the layer that is selected for the input chan-

nel strip in tandem with the [CH 1-24]/[CH 25-48]

keys located in the input channel strip of the panel or

the FADER MODE [A]–[F] keys of the FADER MODE

section. (If the MIDI REMOTE layer is selected, this

will indicate REMOTE 1-24.) For layers other than

MIDI REMOTE, you can move the cursor and turn the

[DATA] encoder to select them directly.

F FADER MODE

This is linked with the FADER MODE section on the

panel, and indicates the function that is assigned to the

faders of the DCA strip. You can also move the cursor

and turn the [DATA] encoder to change this directly.

G ST IN/FX RTN (ST IN channel / Effect

return) layer

This shows the layer that is selected for the ST IN chan-

nel strip in tandem with the [ST IN] key / [FX RTN 1-

4] key located in the ST IN channel strip of the panel or

the FADER MODE [A]–[F] keys of the FADER MODE

section. (If the MIDI REMOTE layer is selected, this

will indicate REMOTE 25-28. If a layer of a machine

other than the input channel layer is selected, the

machine ID number is also shown.) For layers other

than MIDI REMOTE, you can move the cursor and

turn the [DATA] encoder to select them directly.

H DIRECT RECALL/MUTE MASTER

This switches between the following two choices as the

function of the [1]–[8] keys in the SCENE MEMORY

section of the panel.

• DIRECT RECALL

Keys [1]–[8] of the SCENE MEMORY section will

directly recall the scene that was assigned in the SCENE

screen.

• MUTE MASTER

Keys [1]–[8] of the SCENE MEMORY section will

switch mute groups 1–8 on/off.

I USER DEFINED KEY BANK

Indicates the currently selected bank of User Defined

keys. You can also move the cursor and turn the

[DATA] encoder to change this directly.

Here you can select the function that you want to view in

the display. These operate in the same way as the keys of

the DISPLAY ACCESS section.

Hint

To access this screen from another function, click the Func-

tion Name area at the top of the display.

A Global functions

These buttons access functions that affect the entire

PM5D.

B Output-related functions

These buttons access functions related to output chan-

nels (MIX channels, MATRIX channels, STEREO A/B

channels).

C Input-related functions

These buttons access functions related to input chan-

nels (input channels, ST IN channels, FX RTN

channels).

Function menu

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

Global functions

166 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

EFFECT functions

Here you can select the type of internal effect, edit its

parameters, and perform input/output patching.

A Effect selection

Of the internal effects 1–8, select the effect for which

you want to make settings. To switch between effects,

place the cursor here and turn the [DATA] encoder, or

click the / buttons at left or right.

B Effect type

Indicates the currently selected effect type, both by

name and as a graphic. The number of input/output

channels (1 IN/2 OUT or 2 IN/2 OUT) of this effect is

also shown at the bottom of this area.

Note

You can’t switch the effect type in this screen. If you want to

switch to a different effect type, recall an effect that uses the

desired effect type from the effect library.

C Input patch

This box lets you select the signal path that will be

patched to the L/R input channels of the internal effect.

Move the cursor to this box and turn the [DATA]

encoder or click the / buttons at left or right to dis-

play the desired signal path, and then press the

[ENTER] key to finalize the change.

You can choose the following signal paths.

Note

• If you move the cursor away without pressing the [ENTER]

key, the setting will revert to its original state.

• If you assign a signal to both input channels for a 1 IN/2

OUT effect type, the two will be mixed to monaural and then

input.

• If you assign a signal to only one input channel for a 2 IN/2

OUT effect type, the same signal will be sent to both chan-

nels of the effect.

• If STEAL PATCH CONFIRMATION is turned on in the

PREFERENCE 1 screen (UTILITY function), and you

attempt to make patch settings that would cause an existing

patch to be modified, a confirmation message will appear.

D Input meter

Indicates the level of the signal being input to the effect.

Global functions

EFFECT PARAM (Effect parameter)

screen

EFFECT PARAM

2 3 4

MIX1–MIX24 MIX channel 1–24 output

INS CH1–INS CH48 Input channel 1–48 insert out

INS STIN1 (L/R)–INS STIN4

(L/R)

ST IN channel 1–4 (L/R)

insert out

INS MIX1–INS MIX24 MIX channel 1–24 insert out

INS MTRX1–INS MTRX8

MATRIX channel 1–8 insert

out

INS ST A (L/R)

STEREO A channel (L/R)

insert out

INS ST B (L/R)

STEREO B channel (L/R)

insert out

INS MON (L/R/C)

(PM5D only)

MONITOR channel (L/R/C)

insert out

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 167

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

E MIX BALANCE

Adjusts the balance of the effect sound relative to the

original sound.

0 (%) outputs only the original sound, and 100 (%)

outputs only the effect sound.

F BYPASS

This button temporarily bypasses the effect.

G CUE

This button cue-monitors the output of the effect

shown in the screen. Cue is automatically defeated

when you switch to a different screen. (However, cue

will be held if you switch to the EFFECT ASSIGN

screen.)

H Output meter

Indicates the level of the signal being output from the

effect.

I Output patch

This box lets you select the signal path that will be

patched to the L/R output channels of the internal

effect. The selection method is the same as for Input

Patch. You can choose the following signal paths.

Note

Even if you’ve patched multiple channels in the INPUT

PATCH/OUTPUT PATCH function INSERT PATCH screen,

changing the input/output patch in this screen will turn off

patching to other channels.

J LIBRARY

This button accesses the EFFECT LIBRARY screen for

the currently selected effect.

K TEMPO parameter

If a delay-type or modulation-type effect type is

selected, the tempo parameter will be displayed here.

The TEMPO parameter specifies time-related parame-

ters in units of BPM (Beats Per Minute). For a delay-

type effect it sets the DELAY (delay time), and for a

modulation-type effect it sets the FREQ. (modulation

frequency).

Note

For some effect types, a parameter unique to the effect may

be shown instead of the TEMPO parameter. For example if

FREEZE is selected as the effect type, a button for recording/

playing the input signal is shown.

The BPM value can be edited using the on-screen

knob, or by repeatedly clicking the TAP TEMPO but-

ton. (In this case, the average interval between clicks is

detected. If the average value is outside the range of 20–

300 BPM, it will be ignored.)

If the MIDI CLK button is on, the TEMPO parameter

will synchronize to the MIDI timing clock being

received from the MIDI port.

L Effect parameters

This area shows parameters for the currently selected

effect type.

CH1–CH48 Input channel 1–48 input

STIN1–STIN4 (L/R) ST IN channel 1–4 (L/R) input

FXRTN1–FXRTN4 (L/R) FX RTN channel 1–4 input

INS CH1–INS CH48 Input channel 1–48 insert in

INS ST1 (L/R)–INS ST4 (L/

ST IN channel 1–4 (L/R) insert

INS MIX1–INS MIX24 MIX channel 1–24 insert in

INS MTRX1–INS MTRX8 MATRIX channel 1–8 insert in

INS ST A (L/R)

STEREO A channel (L/R)

insert in

INS ST B (L/R)

STEREO B channel (L/R)

insert in

INS MON (L/R/C)

(PM5D only)

MONITOR channel (L/R/C)

insert in

J8 9

K L

ab c

First tap Second tap Third tap Fourth tap

The average of the intervals is input as the parameter

value (average of a, b, and c)

EFFECT functions

168 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

This screen lists the effect types used by internal effects 1–8,

and shows their input levels.. Here you can also assign sig-

nals to input/output channels, and make settings for

bypass and cue.

A Level meter

Indicates the input level to the effect.

B Effect type

Indicates the selected effect type, both by name and as a

graphic. When you click this area, the EFFECT

PARAM screen will appear. You can also drag and

drop this area onto another effect in this screen to copy

the effect settings.

C BYPASS

This button temporarily bypasses the effect.

D CUE

This button cue-monitors the effect output. Cue is

automatically defeated when you switch to a different

screen. (However, cue will be held if you switch to the

EFFECT PARAM screen of the corresponding effect.)

E Input patch

This box indicates the signal path that is patched to the

L/R input channels of the internal effect. You can also

directly assign the signal path in this box.

F Output patch

This box indicates the signal path that is patched to the

L/R output channels of the internal effect. You can also

directly assign the signal path in this box.

Note

Even if you’ve patched multiple channels in the INPUT

PATCH/OUTPUT PATCH function INSERT PATCH screen,

changing the input/output patch in this screen will turn off

patching to other channels.

G DSP CONFIGURATION

This box lets you change the number of assignments

for the internal effects and GEQ modules. If you

decrease the number of internal effects, the number of

available GEQ modules will increase by one. The num-

ber of internal effects can be changed between eight

units (twelve GEQ modules) to zero available internal

effects (twenty GEQ modules).

Note

If you change the DSP CONFIGURATION setting, the inter-

nal effects or GEQ modules may be muted briefly.

EFFECT ASSIGN screen

EFFECT ASSIGN

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 169

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

Here you can recall, store, rename, or delete items in the

effect library.

A EDIT

When you click this button, the EFFECT PARAM

screen for the currently selected effect will appear.

B Effect selection

Of the internal effects 1–8, select the effect for which

you want to make settings.

C Input meter

Indicates the input level of the effect.

D Current effect type

Indicates the effect type of the currently selected effect.

E Output meter

Indicates the output level of the effect.

F Library effect type

Indicates the effect type of the library item selected in

the list.

G RECALL

Recalls the library item shown in the list into the cur-

rently selected effect.

Note

When you recall an Add-On effect, other effects may be

muted briefly.

H STORE

Stores the currently selected effect into the selected

location of the list. When you click this button a win-

dow will appear, allowing you to name and save the

effect.

I TITLE EDIT

Edits the title of the library item selected in the list.

When you click this button a window will appear,

allowing you to edit the title.

J CLEAR

Deletes the library item selected in the list. When you

click this button, a confirmation message will appear.

Note

Library items with an “R” displayed in the right column of the

list are read-only. Read-only items cannot be stored,

renamed, or deleted.

K Library list

Use the scroll bar to select the library item on which

you want to perform an operation. The selected library

item will move to the center, and will be highlighted.

Note

If the library item selected for operations is different than the

last-stored/recalled library item, the last-stored/recalled library

item will be shown with a blue background.

EFFECT LIBRARY screen

EFFECT LIBRARY

3 54

1 2

GEQ function

170 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

In this screen you can make settings for Waves Y96K plug-

in DSP cards installed in slots 1–4. For details on opera-

tion, refer to the Y96K operating manual.

Please note that Y96K cards will operate as follows.

• Settings will be stored/recalled as scene data, but the

Undo function is not supported.

• If you power the PM5D off and then on again, the con-

ventional scene data will be in the state of when the

power was turned off, but the Y96K will be in the state

that was last stored or recalled.

• If you recall a scene that produces a major change in

the Y96K’s settings, the Y96K’s settings will change sev-

eral seconds after recall occurs on the PM5D. If you

want to match this timing, set the appropriate START

OFFSET in the FADE TIME screen.

• Do not execute scene store or recall operations while

the screen indicates that the Y96K is waiting to update.

If you do so, the screen will become inoperable for up

to 30 seconds.

• The Y96K’s settings will be saved in the PM5D when

you store the scene. If in the past you had stored a

scene with a Y96K installed, and you then once again

store that scene without the Y96K installed, the previ-

ous Y96K settings will remain. If there is a scene for

which a Y96K has never been installed, and you install

a Y96K and then recall that scene, nothing will be

reflected in the Y96K.

• In PREVIEW mode, the PLUG-IN screen will not show

the state of the Y96K.

Note

The DSP5D does not support the Y96K.

GEQ function

Here you can adjust the boost/cut for a 31-band graphic

EQ or 8-band parametric EQ, specify the input/output

patching, and assign a GEQ to faders.

A Module select

This selects the GEQ module to operate. To switch

between modules, place the cursor here and turn the

[DATA] encoder, or click the / buttons at left or

right.

B LINK button

This button links adjacent odd-numbered → even-

numbered graphic EQ modules. When you turn this

button on, a window will appear, allowing you to select

whether the parameters will be copied from one mod-

ule to the other, or whether both modules will be

initialized.

PLUG-IN screen

PLUG-IN

GEQ PARAM (GEQ parameter) screen

GEQ PARAM

1 5 6 72 43

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 171

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

C INSERT (Insert destination)

Selects the location at which the GEQ module will be

inserted. Move the cursor to this box and turn the

[DATA] encoder or click the / buttons at left or

right to display the desired insertion destination, and

then press the [ENTER] key to finalize the change.

You can choose the following insertion destinations.

• INS CH1–INS CH48

Input channel 1–48 insert in/out

• INS STIN1 (L/R)–INS STIN4 (L/R)

ST IN channel 1–4 (L/R) insert in/out

• INS MIX1–INS MIX24

MIX channel 1–24 insert in/out

• INS MTRX1–INS MTRX8

MATRIX channel 1–8 insert in/out

• INS ST A (L/R)

STEREO A channel (L/R) insert in/out

• INS ST B (L/R)

STEREO B channel (L/R) insert in/out

• INS MON (L/R/C) (PM5D only)

MONITOR channel (L/R/C) insert in/out

Note

• When you select the insertion destination here, insert in/out

will be patched simultaneously, and insertion will automati-

cally be turned on for the channel into which the graphic EQ

module was inserted.

• If you move the cursor away without pressing the [ENTER]

key, the setting will revert to its original state.

D GEQ/PEQ button

This switches between the 31-band graphic EQ (GEQ)

and 8-band parametric EQ (PEQ).

Note

Even if you switch between GEQ and PEQ, the graphic EQ

and parametric EQ parameters will remember their settings

from before the change.

E EQ ON/OFF button

Switches the currently selected GEQ module on/off.

F LIBRARY

This button accesses the GEQ LIBRARY screen.

G Level meter

This meter indicates the peak level before and after the

GEQ module.

❏ When graphic EQ is selected

H SLOW/FAST

Switches the fall speed of the spectrum analyzer

between slow or fast. This setting does not affect the

meters in other screens or the meters on the panel.

I PEAK HOLD

Switches the peak hold function on/off for the spec-

trum analyzer. The peak level for each band is held

while this button is on. (To reset the peak level display,

turn this button off and then on again). This setting

does not affect the meters in other screens or the

meters on the panel.

J Spectrum analyzer

This is an analyzer that shows a realtime level display

for each band of the input signal.

K EQ graph

Indicates the current frequency response of the graphic

EQ.

L Faders

These faders cut/boost the frequency bands of the

graphic EQ. The actual values are shown in the numer-

ical boxes below.

M ASSIGN TO FADERS

These buttons divide the 31 bands of the graphic EQ

into six groups so that you can use the DCA faders to

adjust the boost/cut amount of each band. Click one of

the six buttons A (20.0-100), B (63.0-315), C (200-

1.00k), D (630-3.15k), E (2.00k-10.0k), F (4.00k-

20.0k). DCA faders 1–8 will be assigned to the corre-

sponding region of frequency bands, allowing you to

control them with the DCA faders. At this time, the

divisions of the corresponding faders and the value in

the numerical box screen will turn red in the screen. To

return to the original state, press the DCA (OFF) but-

ton in the screen or the [DCA] button on the panel.

Note

• If the ASSIGN TO FADERS buttons A–F are off, you can

hold down the [SHIFT] button on the panel and press a

FADER MODE section button [A]–[F], and then use the DCA

faders to control the corresponding region of the graphic EQ

in the same way as if you had pressed a button A–F in the

screen.

• The currently selected DCA fader mode (DCA, A–F) is dis-

abled while one of the ASSIGN TO FADERS buttons A–F is

on. At this time, you can also use the FADER MODE sec-

tion buttons [A]–[F] to switch between regions of the graphic

EQ; the button for the selected region will blink, and the

remaining buttons will light.

• If the AUTO ASSIGN button is off, the setting in the ASSIGN

TO FADERS field is cleared automatically when you switch

screens, and the currently selected DCA fader mode will

once again be enabled.

8 9

NOP

GEQ function

172 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

N LIMIT

The range and direction of adjustment controlled by

the faders can be selected from the following: ±15 dB,

±12 dB, ±6 dB (these are valid in both the boost and

cut directions), or –24 dB (valid only in the cut

direction).

O EQ FLAT

Resets all faders to the 0 dB position. When you click

this button, a confirmation message will appear.

P AUTO ASSIGN

This button automates assignments to the DCA faders.

If this button is on, the most recently selected region of

GEQ bands will be assigned to the DCA faders when

you access the GEQ PARAM screen.

❏ When parametric EQ is selected

Q ASSIGN TO SELECTED CH ON/OFF button

This switches the assignment to the SELECTED

CHANNEL section on/off.

Note

If the AUTO ASSIGN button is off, switching the screen will

make the ASSIGN TO SELECTED CH ON/OFF button turn

off, and you’ll be able to use the SELECTED CHANNEL sec-

tion to operate the parameters of the currently selected

channel.

R AUTO ASSIGN

This button automates assignment to the SELECTED

CHANNEL section. If you leave this button turned on,

the selected frequency band will be assigned to the

SELECTED CHANNEL section when you access the

GEQ PARAM screen if the ASSIGN TO SELECTED

CH ON/OFF button is on.

S EQ TYPE

This selects the EQ type. Turn the TYPE I button on to

choose the algorithm used in conventional Yamaha

digital mixers, or turn the TYPE II button on to choose

a newly-developed algorithm. Using TYPE II will

decrease the interference between bands.

T EQ graph

This graph shows the approximate response of the EQ

parameters. The colored vertical line shows the FREQ

(center frequency) of the band at which the cursor is

located. (The color of each line is the same as the mark-

ings around the knob of each band.) When you edit the

Q or GAIN (gain) of each band, the response curve will

change accordingly.

U EQ FLAT

This resets the GAIN parameter of all bands to the ini-

tial value (±0.0 dB). When you click this button, a

confirmation message will appear.

V LOWER/UPPER

These indicators show which four bands (LOWER or

UPPER) are selected in the SELECTED CHANNEL

section of the panel. The text is shown in yellow to

indicate the set of bands that is selected.

W Knobs

For each band, these knobs adjust the Q, the FREQ

(center frequency), and GAIN (amount of boost/cut).

X BYPASS

This button bypasses each band of the EQ.

Y (LOW shelving)

If this button is on, the LOW EQ will be switched to a

shelving-type. The Q knob will disappear.

Z HPF (High Pass Filter)

If this button is on, the LOW EQ will operate as a high

pass filter. The Q knob will disappear, and the GAIN

knob will be used to turn the HPF on/off.

a LPF (Low Pass Filter)

If this button is on, the HIGH EQ will operate as a low

pass filter. The Q knob will disappear, and the GAIN

knob will be used to turn the LPF on/off.

b (HIGH shelving)

If this button is on, the HIGH EQ will be switched to a

shelving-type. The Q knob will disappear.

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 173

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

This screen lists the approximate values of the GEQ mod-

ule settings, and shows the input/output levels. The signal

path assignments and on/off status can also be edited in

this screen.

A Level meter

This meter indicates the peak level before and after the

GEQ module.

B Fader graph

This indicates the approximate fader position for each

band. When you click this area, the GEQ PARAM

screen for the corresponding GEQ module will appear.

You can also drag and drop this area onto another

GEQ module to copy the GEQ settings.

C GEQ ON/OFF button

Switches the GEQ module on/off.

D Insert destination

Indicates the location at which the GEQ module is

inserted. You can also specify the insert location from

within this screen.

E LINK button

This button indicates the link status of adjacent odd-

numbered → even-numbered GEQ modules. When

you turn this button on, a window will appear, allow-

ing you to select whether the parameters will be copied

from one module to the other, or whether both mod-

ules will be initialized.

F DSP CONFIGURATION

This box lets you change the number of assignments

for the internal effects and GEQ modules. If you

decrease the number of internal effects, the number of

available GEQ modules will increase by one. The num-

ber of internal effects can be changed between eight

units (twelve GEQ modules) to zero available internal

effects (twenty GEQ modules).

Note

If you change the DSP CONFIGURATION setting, the inter-

nal effects or GEQ modules may be muted briefly.

GEQ ASSIGN screen

GEQ ASSIGN

1 2 3

GEQ function

174 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

Here you can recall, store, rename, or delete items in the

GEQ library.

A EDIT

When you click this button, the GEQ PARAM screen

for the currently selected GEQ module will appear.

B GEQ module select

Select the GEQ module for which you want to make

settings.

C GEQ/PEQ

This indicates the type of the selected GEQ. The library

list will indicate either GEQ LIBRARY or OUTPUT EQ

LIBRARY, depending on the current type.

D Current EQ graph

Indicates the approximate response of the currently

selected GEQ module.

E Level meter

This meter indicates the peak level before and after the

GEQ module.

F RECALL

Recalls the library item selected in the list into the cur-

rently selected GEQ module.

G STORE

Stores the settings of the currently selected GEQ mod-

ule into the selected location in the list. When you click

this button a window will appear, allowing you to

name and save the GEQ module settings.

H TITLE EDIT

Edits the title of the library item selected in the list.

When you click this button a window will appear,

allowing you to edit the title.

I CLEAR

Deletes the library item selected in the list. When you

click this button, a confirmation message will appear.

Note

Library items with an “R” displayed in the right column of the

list are read-only. Read-only items cannot be stored,

renamed, or deleted.

J Library EQ graph

Shows the response curve of the library selected in the

list.

K Library list

Use the scroll bar to select the library item on which

you want to perform an operation. The selected library

item will move to the center, and will be highlighted.

GEQ LIBRARY screen

GEQ LIBRARY

1 2 43

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 175

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

SCENE function

Here you can store/recall scenes.

A Scene list

This is a list of the stored scenes. For each scene, the fol-

lowing items are displayed. (To view

COMMENT

and subsequent items, scroll the list to the right.)

B (Scene number)

This is the scene number 0–500. You can click this icon

to reverse the order in which the scenes are sorted.

C TITLE

This is the name assigned to each scene. You can click

the TITLE button to sort the scenes in order of their

titles. When you click the button at the left, a win-

dow will appear, allowing you to edit the title.

D (Protect)

For each scene, this button specifies whether the scene

will be protected and read-only.

• Protect (lock) symbol

The scene cannot be overwritten.

•R (read only) symbol

In addition to the above Protect setting, it will be

impossible to overwrite the scene by loading a file, etc.

This setting can be made only for consecutive scene

numbers starting at scene number 000.

Note

• If LINKED LIBRARY PROTECTION is turned on in the

UTILITY function PREFERENCE 1 screen, libraries that are

linked to READ ONLY scenes will also be protected, but

they will be overwritten when a file is loaded.

• Read Only settings will not be loaded. If you load after initializ-

ing the memory, you’ll have to re-make the Read Only settings.

• No symbol

The scene is not protected in any way.

E SEL.RECALL (Selective recall)

For each scene, you can specify whether the Selective

Recall function will be used when recalling the scene. If

the Selective Recall function is enabled (➥ p.180),

scenes for which this button is turned on can recall

only specific parameters. (Alternatively, you can

exclude only specific parameters from the recall.)

If the scenes are sorted in order of TITLE, a check mark

is displayed for scenes for which this is turned on. If the

scenes are sorted in numerical order, a downward or

upward arrow is displayed for scenes for which this is

turned on; this makes it easy to see which was the origi-

nal scene prior to selective recall.

F Library link

This area shows the number and title of the INPUT

PATCH library, OUTPUT PATCH library, and HA

library used by each scene. You can click the button

at the left to access a window that lets you change the

library number that is linked. The LINK button for

each library determines whether library recall opera-

tions will be linked to scene recall operations.

If the LINK button is on (this column indicates

“LINK”), the library of the corresponding number will

also be recalled when you recall that scene. A library

whose LINK button is off will not change when you

recall that scene.

G COMMENT

In this column you can enter or view a comment for the

scene. A text input window will appear when you move

the cursor to the COMMENT field and press the

[ENTER] key, or when you click the button at the left.

H TIME STAMP

Indicates the time at which the scene was last stored, in

the format of month/day/year/hours/minutes/seconds.

I MIDI EVENT

Specifies a MIDI message that will be transmitted from

the MIDI OUT connector when the scene is recalled.

When you click the button at left a window will

appear, allowing you to input a MIDI event in hexa-

decimal form (➥ p.128).

SCENE screen

SCENE

2 3 45 6

7 8

9 K

SCENE function

176

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual

Reference section

TX ON/OFF (MIDI event transmission on/

off)

Specifies whether the assigned MIDI event will be

transmitted.

DELAY

This specifies the timing of the program change or

MIDI event that will be transmitted when the scene is

recalled. When you click the button at the left, the

following MIDI EVENT DELAY window will appear.

• POST

The program change or MIDI event will be transmit-

ted when scene recall processing is completed (the

same operation as before V1.2).

• INTERVAL

The program change or MIDI event will be transmit-

ted following the specified time interval after scene

recall processing began. The transmission start time

can be specified in a range from 0.0 seconds to 9.9

seconds.

GPI OUT CONTROL 1–12

Specifies the polarity and transmission method (tally/

trigger) of the signal that is sent from GPI OUT ports

1–12 when the scene is recalled. When you click a but-

ton corresponding to a port 1–12, the setting will

change in the following order.

Note

• GPI OUT CONTROL settings are independent of the set-

tings in the MIDI/REMOTE function GPI screen.

• In the case of a Trigger type setting, the time interval

between becoming active and returning to the inactive state

is 250 msec.

REMOTE TRANSPORT

Selects the transport command (MMC or RS422 pro-

tocol) that will be transmitted when you recall the

scene. If you click the button at the left a window

will appear, allowing you to select the output destina-

tion and the type of command.

SCENE FUNCTION

Here you can store/recall scenes.

• RECALL

Loads the scene currently selected in the scene list into

the PM5D.

• STORE

Saves the current settings of the PM5D in the scene

currently selected in the scene list. (This button is inop-

erable if the selected scene is read-only or protected.)

• UNDO

Cancels the preceding Recall or Store operation. You

can click this once again (Redo) to return to the state

prior to Undoing.

• PREVIEW

If this button is on, the PM5D will be in PREVIEW

mode; this allows you to view or edit the settings of a

scene stored in memory or the settings of a library item

without affecting the internal signal processing. This is

linked with the [PREVIEW] key in the SCENE MEM-

ORY section of the panel (

➥

p.88).

Note

• Monitor settings will apply to internal signal processing even

during Preview mode. You can perform cue/monitor opera-

tions while Previewing.

• EVENT LIST, MIDI, and GPI operations will apply to internal

signal processing, but not to Preview.

• Memory card save/load operations cannot be performed

during Preview.

• During Preview, user defined operations that affect internal

signal processing are disabled; such operations include

EVENT LIST, TALKBACK ASSIGN, MONITOR, MIDI

DIRECT OUT, MACHINE CONTROL, and GPI OUT

CONTROL.

L M

Display Polarity

Transmission

method

None Disabled

High active Tally

Low active Tally

High active Trigger

Low active Trigger

N P Q

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 177

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

O BLANK SKIP

Specifies how scene numbers can be selected. If the

BLANK SKIP button is off, all scene numbers can be

selected consecutively regardless of whether they con-

tain scene data. In contrast if the BLANK SKIP button

is on, only numbers in which a scene is actually stored

can be selected. This setting applies when you switch

scenes using the SCENE MEMORY [π]/[†] keys in

the SCENE MEMORY section of the panel, the

[DATA] encoder, or the / buttons in the screen.

P EDIT

These buttons let you rearrange the order of the scenes

in memory.

• CUT

Cuts the scene selected in the list, and holds it in a tem-

porary memory buffer. Subsequent scenes will be

moved forward by one.

• COPY

Copies the scene selected in the list into the memory

buffer. The copy-source and other scenes will not be

affected.

• INSERT

Inserts the scene from the memory buffer at the num-

ber selected in the list. Scenes that follow the number at

which you inserted will be moved backward by one.

• PASTE

Overwrites the scene from the memory buffer onto the

blank number selected in the list. Other scenes will not

be affected.

• CLEAR

Deletes the scene selected in the list.

• UNDO

Cancels the operation that was last performed in the

EDIT area.

Note

•A confirmation message will appear when you click one of

these buttons.

• If a read-only or protected scene is selected in the list, the

CUT, INSERT, and CLEAR buttons are grayed-out, and

cannot be used.

• If an existing scene is selected in the list, the PASTE button

is grayed-out, and cannot be used.

• If the list is sorted by title, the CUT, INSERT, and UNDO

buttons are displayed in gray.

• If you modify the contents of a scene by operations in other

than the EDIT section, the UNDO button is displayed in gray.

Q DIRECT RECALL ASSIGN

This lets you select the scenes that will be directly

recalled by the SCENE MEMORY [1]–[8] keys on the

panel. This function is available if the DIRECT

RECALL button is on.

When you move the cursor to the field on the left and

turn the [DATA] encoder, or when you click the /

buttons to select a scene number, the scene name will

appear in the field on the right.

R DIRECT RECALL/MUTE MASTER

These are linked with the DIRECT RECALL/MUTE

MASTER buttons shown at the bottom of the display.

(➥ p.165)

The Event List function lets you register scenes in the order

of use, so that these scenes can be recalled either manually

or automatically according to the specified time code or

interval.

Note

The setting screen for the PM5D is always shown, even if the

DSP5D is cascade-connected.

A EVENT LIST ENABLE/DISABLE

Use the following three buttons to enable/disable the

Event List function.

• DISABLE

The Event List function will not recall scenes registered

in the event list.

• ENABLE [ALL MANUAL]

Scenes registered in the event list will be recalled only

by manual operation. If the list contains events for

which a time code has been specified, the candidate

event for recall will change as time code progresses, but

events will not actually be recalled unless the recall

operation is performed manually.

• ENABLE

Scenes registered in the event list will be recalled

according to the specified condition (time code, inter-

val, or manual operation).

EVENT LIST screen

EVENT LIST

SCENE function

178 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

B Event list

In this list you can register the scenes to be recalled,

and the conditions under which the scenes will be

recalled. Click a line to select the event of that line for

editing; it will be highlighted in the center of the list.

• No.

Indicates the event number.

• EVENT TRIGGER

This column specifies the condition that will recall each

event. Click the button, and in the window that

appears, use the following three buttons to select the

condition.

MANUAL . . . . . The event can be recalled by the

DIRECT button in the EVENT

RECALL area (

3) or by a User

Defined key. The EVENT TRIG-

GER field will indicate

“[MANUAL]”.

INTERVAL . . . . The scene will be recalled when a

specified time has elapsed after the

preceding scene was recalled. If you

select this button, specify the wait

time in the lower part of the win-

dow. The EVENT TRIGGER field

in the list shows a “ ” symbol and

the wait time.

TIME CODE . . . The scene will be recalled when the

time code (LTC, MTC, internal

time code) reaches the specified

time. If you select this button, spec-

ify the time code location (hours/

minutes/seconds/frames) in the

lower part of the window. The

EVENT TRIGGER field in the list

shows the time code.

Hint

• As long as an event for which MANUAL is specified is

selected in the list, the scene will not change until you manu-

ally execute a recall.

• However, if a event for which TIME CODE is specified is

registered later in the list, events set to MANUAL will be

skipped when that time code arrives, and the corresponding

scene will be recalled.

• The condition for recalling the scene that will be recalled

next is shown in the NEXT SCENE/NEXT EVENT fields in

the upper part of the display.

Note

• If time code source is OFF, events whose EVENT TRIG-

GER is set to TIME CODE will not be recalled unless you

perform a manual recall.

• In contrast, events whose EVENT TRIGGER is set to

INTERVAL will be recalled automatically after the specified

interval elapses from the previous recall operation, even if

the time code source is OFF.

• In the two-second interval after time code starts, events may

not be executed because synchronization is being estab-

lished. You must start time code at least two seconds earlier

than an event you want to execute.

• SCENE TITLE

This is the number and title of the scene to be recalled.

Click the button, and in the window that appears,

click the number of a scene to select it.

C EVENT RECALL

Here you can recall events. The following three but-

tons are provided.

• PREV

When you click this button, the event of the line pre-

ceding the last-recalled event will be recalled and

selected.

• DIRECT

When you click this button, the event currently

selected in the event list will be recalled. This is used

mainly to recall an event whose EVENT TRIGGER

field is set to “[MANUAL]”.

• NEXT

When you click this button, the event of the line fol-

lowing the last-recalled event will be recalled and

selected.

D AUTO CAPTURE

This button lets you automatically register events in

realtime while time code runs. If time code is running

and this button is on, using the buttons of the panel

SCENE MEMORY to recall a scene will cause the cor-

responding scene number and time code location to be

captured, and this will be added as a new event.

Note

• If the list contains previously-recorded events, they will be

sorted in descending order of their time code.

• If an event already exists at the identical time code location,

it will be overwritten by the new event.

• Even if time code source is “OFF,” performing a recall oper-

ation while this button is on will register a new event in the

list. In this case, the EVENT TRIGGER field will be regis-

tered as “[MANUAL]”.

• If an offset value is specified, the sum of the offset value and

the displayed time code is captured as the time code.

Event that will be recalled manually

Event that will be recalled when time code reaches the

speciﬁed location

Event that will be recalled when the speciﬁed interval elapses

after the previous recall operation

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 179

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

E MOVE UP

This button moves the currently selected event one

position earlier in the event list.

F MOVE DOWN

This button moves the currently selected event one

position later in the event list.

Note

• The MOVE UP/DOWN buttons are available only for events

whose EVENT TRIGGER field is shown as “[MANUAL]” or

the “ ” symbol.

• If the EVENT TRIGGER field of the selected event shows a

time code, these buttons will be grayed-out and unavailable.

G MANUAL INSERT

This button inserts a new event at the location selected

in the event list. The EVENT TRIGGER field of the

new event will be “[MANUAL],” and its SCENE TITLE

field will be “no assignment.” You can change these as

desired.

H MANUAL OVERWRITE

This button overwrites a new event onto the location

currently selected in the event list. (If the line at the

current location is blank, this button will be grayed-out

and unavailable.) The EVENT TRIGGER field of the

new event will be “[MANUAL].”

I TIME CODE SETUP

Here you can make settings for the time code received

by the PM5D.

• TC SOURCE (Time code source)

Select one of the following as the time code source that

will be used.

OFF . . . . . . . . . . Time code will not be received.

INTERNAL . . . . The time code generated within the

PM5D will be used.

TIME CODE . . . The time code (LTC) received via

the rear panel TIME CODE connec-

tor will be used.

MIDI . . . . . . . . . The MIDI time code (MTC)

received via the rear panel MIDI IN

connector will be used.

USB . . . . . . . . . . The MIDI time code received from

the specified port via the rear panel

USB connector will be used.

SLOT 1–4 . . . . . If a card that supports MIDI input

is installed in one of the rear panel

slots, the MIDI time code received

from the specified port will be used.

Note

• This setting does not affect the MIDI REMOTE function MIDI

SETUP screen.

• If you select USB or SLOT 1–4, you will need to specify the

port number (1–8) in the field on the right (Depending on the

card that is installed, some slots may have only one port.)

• If you switch to INTERNAL, the time code will be set to the

Start Time value.

• FRAME RATE

Select one of the following as the frame rate for the

time code (LTC, MTC, internal time code) you are

using.

30 . . . . . . . . . . 30 frames/second (non-drop)

30D . . . . . . . . . 30 frames/second (drop frame)

29.97 . . . . . . . . 29.97 frames/second (non-drop)

29.97D . . . . . . 29.97 frames/second (drop frame)

25 . . . . . . . . . . 25 frames/second

24 . . . . . . . . . . 24 frames/second

• OFFSET TIME/START TIME

If INTERNAL is selected as the time code source, use

this field to specify the time at which internal time code

will begin (START TIME).

If any other time code source is selected, use this field

to specify the offset (OFFSET TIME). The offset is the

interval by which the timing at which scenes are

recalled is adjusted backward or forward relative to the

incoming time code (LTC or MTC).

In either case, you can edit the value by clicking the

button and specifying the value in hours/minutes/sec-

onds/frames units in the window that appears.

J Time code display area

This displays the value of the incoming time code (LTC

or MTC) or the internal time code. If INTERNAL is

selected as the time code source, transport buttons are

shown immediately below the time code value; you can

use these buttons to rewind, stop, or start the internal

time code.

In addition, if INTERNAL is selected you can click the

button to access the TIME CODE window, and

specify the time code directly.

Note

An offset value is not added to the displayed time code.

K TIME CODE INSERT

This button registers the time code data in the list in

realtime. When the time code source is running, click-

ing this button will capture the time code value and

add it as a new event. The captured time code is input

in the EVENT TRIGGER field of the new event, and

the SCENE TITLE field will be “no assignment.” At this

time, the events within the list are sorted in descending

order of time code. (If an event exists at the same time

location, it will be overwritten by the new event.)

Note

If the time code source is OFF, the EVENT TRIGGER column

will be “[MANUAL].” If the time code source is TIME CODE,

MIDI, USB, or SLOT 1–4, the offset value has been added to

the time code value of the newly added event.

L TIME CODE OVERWRITE

This button replaces the time code of the event selected

in the list in realtime. When the time code source is

running, clicking this button will write the current time

location as the time code value of the currently selected

event. (The SCENE TITLE field will not change.) At

this time, the events within the list are sorted in

descending order of time code.

If a blank line is selected, this button is grayed-out.

RETURN TO START TIME

(rewind the time code to

the start time)

START

(start the time code

from the current

location)

STOP

(stop the time code)

SCENE function

180 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

Note

If the time code source is OFF, the EVENT TRIGGER column

will be “[MANUAL].” If the time code source is TIME CODE,

MIDI, USB, or SLOT 1–4, the offset value has been added to

the rewritten time code value.

M SCENE INSERT

This button inserts one or more consecutive scenes

from scene memory into the event list. Use the FROM/

TO fields located at right to specify the starting and

ending scene numbers, and click this button; the speci-

fied scenes will be inserted as new events for recall

immediately before the currently selected event. The

EVENT TRIGGER field is set to “[MANUAL]” for all

of the new events.

N SCENE OVERWRITE

This button overwrites the scene assignments of con-

secutive events in the event list with multiple

consecutive scenes from scene memory. Use the

FROM/TO fields located at right to specify the starting

and ending scene numbers, and click this button; start-

ing at the currently selected line of the event list, the

SCENE TITLE field of the corresponding number of

subsequent events will be rewritten to the scenes you

specified. (The EVENT TRIGGER field will not

change.) If a blank line is selected, this button is

grayed-out.

O DELETE

This button deletes the event selected in the event list.

If a blank line is selected, this button is grayed-out.

P UNDO

This button returns the event list to its state prior to the

most recent editing operation. If undo cannot be exe-

cuted, this button is grayed-out.

Q ALL DELETE

This button deletes all events from the event list. When

you click this button, a confirmation message will

appear.

Note

If you edit the list (

–

) or change the time code, the

NEXT EVENT button in the constantly-displayed area will

search from the current time code. However if the time code

source is OFF, or if there is no time code setting in the EVENT

TRIGGER field (only for [MANUAL] and [INTERVAL]), the

NEXT EVENT will be the beginning of the list.

In this screen you can make settings for the Selective Recall

function, which, independently for each scene, lets you

exclude specific parameters/channels from recall, or con-

versely recall only specific parameters/channels.

A SELECTIVE RECALL ENABLED/DISABLED

Enables/disables Selective Recall for the currently

selected scene. If this button is set to DISABLED, the

Selective Recall function is disabled.

Note

• Unlike the RECALL SAFE screen (

➥

p.182) which is com-

mon to all scenes, the settings in the SELECTIVE RECALL

screen are independent for each scene.

• If you edit the settings of the SELECTIVE RECALL screen,

you must store that scene in order to make your changes

effective.

B SELECTION MODE

Use the following two buttons to choose how you want

to use the SELECTIVE RECALL screen.

• SAFE PARAMETER button

If this button is on, you can specify the channels/

parameters that will be excluded from recall

operations.

• RECALL PARAMETER button

If this button is on, you can specify the channels/

parameters that will be recalled.

Immediately after you switch buttons, all channels/

parameters will be subject to recall.

C OUTPUT ISOLATION

If the ON button is on, output channels and parame-

ters to be excluded from recall operations can be

memorized in SETUP memory (not included in mem-

ory card load operations) separately from the Recall

Safe function. To specify the output channels and

parameters that will be excluded from recall, make set-

tings in the OUTPUT ISOLATION SETUP window

that appears when you click the button.

SELECTIVE RECALL screen

SELECTIVE RECALL

1 32

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 181

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

D SAFE ON/OFF buttons

RECALL ON/OFF buttons

The function of these buttons will depend on the

SELECTION MODE (

2) setting.

If the SAFE PARAMETER button is on

These buttons function as SAFE ON/OFF buttons that

specify the channels excluded from recall operations.

If the RECALL PARAMETER button is on

These buttons function as RECALL ON/OFF buttons

that specify the channels that will be recalled.

E Parameter matrix grid

Here you can select the parameters that will be recalled

(or excluded from recall). SAFE PARAMETER selec-

tions are shown in green, and RECALL PARAMETER

selections are shown in blue. If the ALL button is on, all

parameters other than CH to MIX will be recalled (or

excluded from recall).

Note

• Matrix grids corresponding to combinations that cannot be

selected are grayed-out.

• Settings in the parameter matrix grid are ignored for chan-

nels whose SAFE ON/OFF button or RECALL ON/OFF

button is switched off.

F ASSIGN

This area indicates the number of assigned channels for

each parameter.

G SET ALL

These buttons turn on the buttons of all channels or all

buttons of the corresponding parameter.

H CLEAR ALL

These buttons turn off the buttons of all channels or all

buttons of the corresponding parameter.

I OTHER SAFE/RECALL PARAMETERS

By using these buttons, parameters other than those

described above can be excluded from recall

operations.

If the SAFE PARAMETER button is turned on in the

SELECTION MODE (

2) area, these buttons specify

the parameters that will be excluded from recall. If the

RECALL PARAMETER button is turned on, these but-

tons specify the parameters that will be recalled.

The DCA area contains a WITH NAME button. This

lets you specify whether the DCA group name will be

subject to recall operations.

J SET ALL

This button turns on all buttons of the OTHER SAFE

PARAMETERS area.

K CLEAR ALL

This button turns off all buttons of the OTHER SAFE

PARAMETERS area.

4 5

SCENE function

182 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

When using Selective Recall, parameters of which only one

instance for every two adjacent odd-numbered/even-num-

bered channels/modules will be handled as follows if only

one of the channels/modules is set to Selective Recall.

• PAIR

These parameters will not be recalled.

• GATE STEREO LINK

• COMP STEREO LINK

• GEQ LINK

The LINK parameter will be forcibly turned off (link-

ing will be disabled).

• DELAY GANG

• ATT GANG

The GANG parameter will be recalled. If GANG is

turned on because of the recall, operation will main-

tain the difference in the DELAY/ATT parameter

values following the recall.

• MS DECODE

• FIXED/VARI

These parameters will not be recalled.

• PAN MODE

The PAN MODE parameter will be recalled. However

if the PAN MODE would be changed by the recall from

BALANCE to any other setting, or if it would be

changed to BALANCE from any other setting, the PAN

MODE and PAN parameters will not be recalled. If the

recall causes PAN MODE to be set to GANG PAN, the

difference in PAN parameter values will be maintained

for operation following the recall.

Note

• Recall Safe and Selective Recall can be used together.

Channels/parameters excluded from recall operations by

either Recall Safe or Selective Recall (or both) will not be

recalled.

• Selective Recall applies when a scene is recalled in PRE-

VIEW mode.

• When you recall a scene, there may be cases in which a

conflict in pairing settings between Recall Safe and Selec-

tive Recall causes the settings of a parameter to differ

between L and R channels. In such cases, the parameter

will be linked when it is next operated.

Here you can specify parameters/channels that will be

excluded from recall operations for all scenes.

A SAFE KEY MODE SELECT (Safe Key Mode

selection)

If the HA+CH button is on, Recall Safe will also turn

on/off for the HA patched to the corresponding chan-

nel when you operate the panel [RECALL SAFE] key or

the RECALL SAFE button (INPUT VIEW function CH

VIEW screen) to turn Recall Safe on/off. If the CH but-

ton is on, this will not be linked.

B OUTPUT ISOLATION

If the ON button is on, output channels and parame-

ters to be excluded from recall operations can be

memorized in SETUP memory (not included in mem-

ory card load operations) separately from the Recall

Safe function (➥ p.180).

RECALL SAFE screen

RECALL SAFE

1 2

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 183

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

C HA SAFE ON/OFF (Head Amp safe on/off)

buttons

These buttons select the channels whose assigned HA

(Head Amp) will be excluded from recall operations.

Note

If you scroll the scroll bar downward, you will see that the CH

column of the SAFE PARAMETERS area shows not only

input channels but also the following input ports.

AD1-AD48 . . . .INPUT jacks 1-48

AD1L-AD4R . . . L/R channels of ST IN jacks 1-4

ExHA1-1–ExHA8-8. . . . . Channels 1-8 of external head amps

1-8 (AD8HR or AD824)

D CH SAFE ON/OFF (Channel safe on/off)

buttons

These buttons select the channels that will be excluded

from recall operations. These are linked with the

[RECALL SAFE] key of the panel.

E Parameter matrix grid

Here you can select the channel parameters that will be

excluded from recall operations. If the ALL button is

on, all parameters except for CH to MIX will be

excluded.

Recall Safe and Selective Recall can be used together.

Channels/parameters excluded from recall operations

by either Recall Safe or Selective Recall (or both) will

not be recalled.

Note

Settings in the parameter matrix grid are ignored for channels

whose CH SAFE ON/OFF button is OFF.

F ASSIGN

This area indicates the number of assigned channels for

each parameter.

G SET ALL

These buttons turn on the buttons of all channels or all

buttons of the corresponding parameter.

H CLEAR ALL

These buttons turn off the buttons of all channels or all

buttons of the corresponding parameter.

I SELECTIVE RECALL PARAMETERS PASTE

This button copies parameter settings from the SELEC-

TIVE RECALL screen, and pastes them into the

RECALL SAFE screen. When you click the button, a

confirmation message will appear.

J OTHER SAFE PARAMETERS

By using these buttons, parameters other than those

described above can be excluded from recall

operations.

The DCA area contains a WITH NAME button. If this

button is on, Recall Safe will apply to the DCA group

name of DCA groups that are on. If the WITH NAME

button is off, the DCA group name is excluded from

Recall Safe.

K SET ALL

This button turns on all buttons of the OTHER SAFE

PARAMETERS area.

L CLEAR ALL

This button turns off all buttons of the OTHER SAFE

PARAMETERS area.

3 4 5

SCENE function

184 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

When using Recall Safe, parameters of which only one

instance for every two adjacent odd-numbered/even-num-

bered channels/modules will be handled as follows if only

one of the channels/modules is set to Recall Safe.

• PAIR

The setting will be forcibly turned off (pairing will be

disabled).

• GATE STEREO LINK

• COMP STEREO LINK

• GEQ LINK

The LINK parameter will be forcibly turned off (link-

ing will be disabled).

• DELAY GANG

• ATT GANG

The GANG parameter will be recalled. If GANG is

turned on because of the recall, operation will main-

tain the difference in the DELAY/ATT parameter

values following the recall.

• MS DECODE

• FIXED/VARI

These parameters will not be recalled.

• PAN MODE

The PAN MODE parameter will be recalled. However

if the PAN MODE would be changed by the recall from

BALANCE to any other setting, or if it would be

changed to BALANCE from any other setting, the PAN

MODE and PAN parameters will not be recalled. If the

recall causes PAN MODE to be set to GANG PAN, the

difference in PAN parameter values will be maintained

for operation following the recall.

Hint

• Selective Recall applies when a scene is recalled in PRE-

VIEW mode.

• When you recall a scene, there may be cases in which a

conflict in pairing settings between Recall Safe and Selec-

tive Recall causes the settings of a parameter to differ

between L and R channels. In such cases, the parameter

will be linked when it is next operated.

Here you can specify how fader and pan will change

smoothly to their new values over a specified duration

when the scene is recalled.

A FADING ENABLED/DISABLED

Enables/disables the Fade function for fader levels.

Note

• The settings in the FADE TIME screen are independent for

each scene. If you edit these settings, you must store that

scene in order to make your changes effective.

• The Fade function will apply when you recall a scene for

which the ENABLED button is selected.

B INPUT CH PANNING ENABLED/DISABLED

(Input channel panning enable/disable)

If the ENABLED button is selected, the Fade function

will also apply to the PAN (BALANCE) parameter of

input channels. This button is independent from the

FADING ENABLED/DISABLED (

1) setting. Use the

following two buttons to select the input channels to

which this will apply.

• When the ALL INPUT button is on

The Fade function will apply to the PAN (BALANCE)

parameter of all input channels.

• When the SAME AS FADING button is on

The Fade function will apply to the PAN (BALANCE)

parameter of only the input channels you select in

C FADE TIME/START OFFSET

Use the following two buttons to select the parameters

that can be viewed/edited in the FADE TIME screen.

The indication at the right shows which button is cur-

rently selected.

• When the FADE TIME button is on

Edit the time (fade time) over which the fader or pan

parameter of the corresponding channel will reach the

new value when you recall a scene for which the Fade

function is enabled.

FADE TIME screen

FADE TIME

1 2 3

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 185

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

• When the START OFFSET button is on

Edit the time (start offset time) after which the fader or

pan parameter of the corresponding channel will begin

changing when you recall a scene for which the Fade

function is enabled.

D Channel settings

Here you can turn the Fade function on/off and spec-

ify the fade time (or the start offset time) for each input

channel / output channel.

Use the channel name buttons to switch the Fade func-

tion on/off. The box below each button lets you specify

the fade time or start offset time. Move the cursor to a

box, and turn the [DATA] encoder or click the /

buttons at the left and right to edit the value.

The color of the numerical value shown in the box will

change as follows.

• When the FADE TIME button is on

The value is displayed in white for channels whose start

offset time is “----” (unset), and in light blue for chan-

nels that are set to 0.1 or above.

• When the START OFFSET button is on

The value is displayed in red for channels whose start

offset time is “----” (unset), and in yellow for channels

that are set to 0.1 or above.

If desired, you can copy the fade time / offset time

value from one channel to another as follows. Move

the cursor to the box that displays the value you want

to copy; then hold down the [SHIFT] key and press the

[ENTER] key to access the JOB SELECT window.

In this window, select the copy-destination item and

click the OK button; the value of the selected channel

will be copied.

E SET ALL

This button enables the Fade function for all input

channels or output channels.

F CLEAR ALL

This button disables the Fade function for all input

channels or output channels.

4 65

SCENE function

186 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

Here you can make settings for the Tracking Recall func-

tion, which adds a specified offset value to the value of each

fader when you recall a scene.

A TRACKING RECALL ENABLED/DISABLED

Enables/disables the Tracking Recall function.

Hint

The settings in the TRACKING RECALL screen apply to all

scenes.

B DISPLAY SELECT

These buttons select the type of channels that are

shown in the TRACKING RECALL screen; either

INPUT (input channels) or OUTPUT (output

channels).

C SET ALL

This button enables Tracking Recall for all channels

(including channels not currently shown in the screen).

D CLEAR ALL

This button disables Tracking Recall for all channels

(including channels not currently shown in the screen).

E OFFSET LOCK

If this button is on, the sliders of all channels (includ-

ing channels not currently shown in the screen) will be

grayed-out, and you will be unable to edit the offset

value.

F ON (Tracking On)

These buttons enable/disable tracking for each chan-

nel. If the TRACKING RECALL ENABLED/

DISABLED button is set to ENABLED, tracking is

enabled on channels for which this button is ON.

Note

If OFFSET LOCK (

) is off, turning this button on will reset

the tracking offset of the corresponding channel to 0 dB. If in

this state you operate the fader of the corresponding channel,

the relative amount of fader movement from the point at which

this button was turned on will be memorized as the tracking

offset. You can then turn OFFSET LOCK on to lock the offset.

This offset value will be added whenever you subsequently

recall a scene.

G Tracking offset

Here you can specify the offset value applied to each

channel if tracking is enabled. The range is ±15 dB.

While OFFSET LOCK (

5) is off, operating the panel

faders will cause these values to change as well; how-

ever, adjusting the offset values in the screen will not

cause the panel faders to move.

TRACKING RECALL screen

TRACKING RECALL

21 5

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 187

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

This screen lets you copy parameter settings of any desired

channel or parameter in the current scene, and paste them

into one or more scenes in scene memory.

A PASTE MODE

Select the type of copy-source parameter from the fol-

lowing choices. You cannot select more than one type

simultaneously.

INPUT . . . . . . Input channel parameters

OUTPUT . . . . Output channel parameters

DCA, GEQ, EFFECT . . . . DCA level or mute on/off

status, GEQ settings, inter-

nal effect settings

B CURRENT SCENE

Here you can select the channels and parameters that

will be copied from the currently selected scene. The

contents shown in this area will depend on the paste

mode (

1) you choose.

• If Paste Mode= INPUT

Select input channels in the left area, and select param-

eters in the right area. You can select the following

parameters.

• If Paste Mode= OUTPUT

Select output channels in the left area, and select

parameters in the right area. You can select the follow-

ing parameters.

Note

• If Paste Mode= INPUT, and the parameter being pasted is

NAME, the name library linked to the selected scene will be

searched automatically and pasted.

• Be aware that if other scenes link to this library, the paste

operation will overwrite the library, meaning that other

scenes may be affected.

GLOBAL PASTE screen

GLOBAL PASTE

ALL

All parameters except for HA, PATCH, and

NAME

ATT Attenuator

EQ EQ function settings

GATE GATE function settings

COMP COMP function settings

DELAY DELAY function settings

FADER Fader level

ON CH [ON] key on/off status

PAN/BAL Pan/balance settings

INSERT Insert on/off status and insert point

SEND

*1. If the SEND button is on, use the MIX buttons (1–24) to

select the applicable MIX bus. If the MIX bus is paired,

SEND PAN is included in PAN/BAL if FOLLOW PAN

“VARI” is on, or included in SEND if it is off.

Send level to the desired MIX bus(es)

DCA Associated DCA group

MUTE Associated mute group

LCR LCR screen settings

Settings for the head amp assigned to the

corresponding input channel

PATCH

Settings for the input patch assigned to the

corresponding input channel

NAME

Name assigned to the corresponding input

channel

EQ EQ function settings

COMP COMP function settings

DELAY DELAY function settings

FADER Fader level

ON CH [ON] key on/off status

BAL Balance settings

INSERT Insert on/off status and insert point

TO MTRX

*1. If the TO MTRX button is on, use the MATRIX buttons

(1–8) to select the applicable MATRIX bus.

Send level to the desired MATRIX bus(es)

DCA Associated DCA group

MUTE Associated mute group

LCR LCR screen settings

WITHOUT

MIX SEND/

WITH MIX

SEND

Selects whether the send level sent from

input channels to the selected MIX bus will

be included (WITH...) or will not be included

(WITHOUT...) in the pasted data.

MIDI REMOTE function

188 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

C DESTINATION SCENE (Paste-destination

scene)

This list lets you select the scenes to which the data will

be pasted. If you want to select multiple consecutive

scenes as the paste-destination, select the starting num-

ber in the upper list and the ending number in the

lower list. (If you’re pasting to only one scene, select

the same scene in the upper and lower lists.)

You can change the order in which the list is sorted by

clicking the buttons shown at the top of the scene

number, SCENE TITLE, TIME STAMP, or COM-

MENT columns.

D PASTE

This button executes the Global Paste operation. When

you click this button, a confirmation message will

appear.

In the case of parameters such as those listed below, of

which only one exists for each two adjacent odd-num-

bered/even-numbered channels or modules, the

parameter will be pasted only if both channels/mod-

ules are specified for pasting.

• GATE STEREO LINK

• COMP STEREO LINK

• DELAY GANG

• PAN MODE

• GEQ LINK

• ATT GANG

• MS DECODE

• FIXED/VARI

Note

• Paste is valid even in PREVIEW mode.

• When you paste to a scene, there may be cases in which a

conflict in pairing settings causes the settings of a parame-

ter to differ between L and R channels. In such cases, the

parameter will be recalled with those settings, and will be

linked when it is next operated.

MIDI REMOTE function

Note

The various MIDI REMOTE function screens other than the

DME CONTROL screen are invalid if the DSP5D is selected.

Here you can select the types of MIDI message transmitted

and received by the PM5D, and select the MIDI port that

will be used.

A MODE

Here you can select the way in which program changes

and control changes will be transmitted/received.

• PROGRAM CHANGE MODE

In this area you can select the program change trans-

mission/reception method.

SINGLE

If this button is on, program changes will be trans-

mitted/received on a single MIDI channel (Single

mode).

OMNI ON/OFF

If this button is on, program changes of all MIDI

channels will be received in Single mode (this is

unavailable in Multi mode).

MIDI SETUP screen

MIDI SETUP

1 2 3 4

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 189

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

BANK ON/OFF

If this button is on, bank select messages will be trans-

mitted and received in Single mode (this is

unavailable in Multi mode).

MULTI

If this button is on, program changes will be trans-

mitted/received on multiple MIDI channels (Multi

mode).

Hint

• If program change reception is on, the PM5D’s scenes or

effects will switch when the appropriate program change is

received from an external device. Additionally, if transmis-

sion is on, program changes will be transmitted to an

external device when scenes or effects are switched on the

PM5D.

• The scene/effect assignment for each program change num-

ber is made in the MIDI PGM CHANGE screen (

➥

p.190).

• CONTROL CHANGE MODE

In this area you can select the control change transmis-

sion/reception method.

NRPN

If this button is on, PM5D mix parameters will be

transmitted/received as NRPN messages.

TABLE [SINGLE]

If this button is on, PM5D mix parameters will be

transmitted/received as control change messages on a

single MIDI channel.

TABLE [MULTI]

If this button is on, PM5D mix parameters will be

transmitted/received as control change messages on

multiple MIDI channels.

Hint

• If control change reception is on, the PM5D’s parameters

will change when the appropriate control change is received

from an external device. If transmission is on, a control

change will be transmitted to an external device when you

edit a parameter on the PM5D.

• If NRPN is selected as the control change mode, the assign-

ment of parameters to NRPN is pre-defined and cannot be

changed.

• If TABLE [SINGLE] or TABLE [MULTI] is selected as the

control change mode, the parameter assignment for each

control number can be edited in the MIDI CTRL CHANGE

screen (

➥

p.191).

B Tx (MIDI transmission)

Here you can make various settings for transmission of

MIDI messages.

• MIDI PORT Tx (MIDI transmission port)

Select the port at which the PM5D will transmit MIDI

messages. You have the following choices.

MIDI . . . . . . . The rear panel MIDI IN connector

USB . . . . . . . . The rear panel USB connector

SLOT 1–4 . . . A card that supports serial transmis-

sion and is installed in rear panel slot

1–4

Move the cursor to this box and turn the [DATA]

encoder or click the / buttons at left or right to

change the setting; then press the [ENTER] key to

finalize the change.

If you select USB or SLOT 1–4, you will need to spec-

ify the port number (1–8) in the field on the right

(Depending on the card that is installed, some slots

may have only one port.)

• SINGLE MODE MIDI CH Tx (MIDI transmission

channel for Single mode)

Select the MIDI channel on which the PM5D will

transmit program changes, control changes, parameter

changes, and bulk data. (This setting is valid only in

Single mode.) Move the cursor to this box and turn the

[DATA] encoder or click the / buttons at left or

right to change the setting; then press the [ENTER] key

to finalize the change.

• PROGRAM CHANGE Tx (Program change

transmission)

• CONTROL CHANGE Tx (Control change

transmission)

• PARAMETER CHANGE Tx (Parameter change

transmission)

These buttons turn transmission on/off for program

changes, control changes, and parameter changes

respectively.

Hint

Parameter changes are a method by which PM5D parame-

ters are transmitted in the form of system exclusive

messages.

• MIDI THRU Tx (Thru output)

Select the port from which messages input to MIDI

THRU Rx will be output. The selection method is the

same as for MIDI PORT Tx.

C Rx (MIDI reception)

Here you can make various settings for reception of

MIDI messages.

• MIDI PORT Rx (MIDI reception port)

Select the port from which the PM5D will receive

MIDI messages.

• SINGLE MODE MIDI CH Rx (MIDI reception chan-

nel for Single mode)

Select the MIDI channel on which the PM5D will

receive program changes, control changes, parameter

changes, and bulk data. (This setting is valid only in

Single mode.)

• PROGRAM CHANGE Rx (Program change

reception)

• CONTROL CHANGE Rx (Control change

reception)

• PARAMETER CHANGE Rx (Parameter change

reception)

These buttons turn transmission on/off for program

changes, control changes, and parameter changes

respectively.

• MIDI THRU Rx (Thru input)

Here you can select the port that will “thru input” the

received MIDI messages.

D ECHO (MIDI message echo output)

Here you can select whether received program changes,

control changes, parameter changes, and other MIDI

messages will be echoed out from the MIDI transmis-

sion port.

MIDI REMOTE function

190 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

E MMC OUTPUT PORT

This selects the port that will transmit MMC (MIDI

Machine Control).

F MIDI REMOTE OUTPUT PORT (MIDI remote

output port)

Here you can select the port from which MIDI mes-

sages will be transmitted by the MIDI Remote

function, for each of the four banks. Incoming mes-

sages used by the LEARN function of the MIDI

REMOTE screen are also received at this port.

G PM5D EDITOR (PM5D EDITOR connection

port)

Here you can select the port and ID number (1–8) used

to communicate with the PM5D Editor application,

which controls the PM5D from a computer.

In this screen you can select the scene or effect library

assigned to each MIDI program number.

A MIDI SETUP

Select the ports that the PM5D will use to transmit and

receive MIDI messages, and the MIDI channels. This

item is linked with the settings in the MIDI SETUP

screen.

B PROGRAM CHANGE SETUP

Here you can specify how program changes will be

transmitted and received, and turn transmission and

reception on/off. This item is linked with the settings in

the MIDI SETUP screen.

C ECHO ON/OFF

This selects whether program changes received from an

external device are echoed-out from the MIDI trans-

mission port. This item is linked with the settings in the

MIDI SETUP screen.

MIDI PGM CHANGE (MIDI program

change) screen

MIDI PGM CHANGE

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 191

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

D List

In this list you can view and select the event (scene

recall / effect library recall) assigned to each program

number.

• CH/BANK (Channel/Bank)

Indicates the MIDI channel on which the program

change is transmitted/received. In Single mode when

the BANK ON/OFF button is on, this column is dis-

played as BANK, and the value shown corresponds to

the bank number.

• PGM No. (Program number)

Indicates the program number 1–128.

• LIBRARY NAME

Here you can view/select the type and the number of

the event (scene or effect) assigned to each channel/

program number.

To make an assignment, click the desired line to select

it. (That line will be highlighted in the center of the

list.) Click the button shown at the left of the

LIBRARY NAME field; the MIDI PGM CHANGE

SETUP window will appear. In this window you can

select the type of event (a scene, or a library item for

effect 1–8) and its number.

When a program change on the corresponding MIDI

channel is received, the event assigned to that program

number will be recalled. In addition, the correspond-

ing program change will be transmitted when this

event is recalled on the PM5D.

E PRESET

Clicking this button will restore all event assignments

in the list to their default state.

F CLEAR ALL

Clicking this button will delete all event assignments in

the list.

Here you can select the PM5D parameter (fader operation,

[ON] key operation, etc.) assigned to each control number.

A MIDI SETUP

Select the ports that the PM5D will use to transmit and

receive MIDI messages, and the MIDI channels. This

item is linked with the settings in the MIDI SETUP

screen.

B CONTROL CHANGE SETUP

Here you can specify how control changes will be

transmitted and received, and turn transmission and

reception on/off. This item is linked with the settings in

the MIDI SETUP screen. You have the following

choices of transmission/reception method.

• NRPN

If this button is on, PM5D mix parameters will be

transmitted/received as NRPN messages.

• TABLE [SINGLE]

If this button is on, PM5D mix parameters will be

transmitted/received as control change messages on a

single MIDI channel according to the assignments in

the list (

4).

• TABLE [MULTI]

If this button is on, PM5D mix parameters will be

transmitted/received as control change messages on

5 64

MIDI CTRL CHANGE (MIDI control

change) screen

MIDI CTRL CHANGE

MIDI REMOTE function

192 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

multiple MIDI channels according to the assignments

in the list (

4).

C ECHO ON/OFF

This selects whether control changes received from an

external device are echoed-out from the MIDI trans-

mission port. This item is linked with the settings in the

MIDI SETUP screen.

D List

In this list you can view/select the events assigned to

each control number.

• CH (Channel)

Indicates the MIDI channel on which the control

change is transmitted/received.

• CTRL No. (Control number)

Indicates the control number 0–119. Control numbers

0, 32, and 96–110 cannot be specified.

• CTRL CHANGE EVENT (Control change event)

Indicates/selects the type of event assigned to the corre-

sponding channel / control number.

To make an assignment, click the desired line (that line

will be highlighted in the center of the list); then click

the button at the left of the CTRL CHANGE

EVENT field to open the MIDI CTRL CHANGE

SETUP window. In this window you can specify the

parameter in three levels (mode, parameters 1/2).

When a control change on the corresponding MIDI

channel is received, the event assigned to that control

number will be edited. In addition, the corresponding

control change will be transmitted when this event is

edited on the PM5D.

Note

This list is ignored if the control change mode is set to NRPN.

E PRESET

Clicking this button will restore all event assignments

in the list to their default state.

F CLEAR ALL

Clicking this button will delete all event assignments in

the list.

Here you can assign MIDI messages to panel faders, CH

[ON] keys, encoders, and ENCODER [ON] keys, and

make settings for the MIDI Remote function used to con-

trol external devices.

A TRANSMIT ENABLED/DISABLED (Enable/

disable transmission)

Enables/disables the MIDI Remote function. You can

enable/disable this function for each of the four banks

(memories in which MIDI Remote settings are stored).

B ASSIGN TO CH STRIP SECTION (Assign to

channel strip)

You can choose the following two as the channel strip

to which the MIDI Remote function is assigned (both

can be selected simultaneously if desired).

INPUT CH . . . . . . . INPUT channel strip 1–24

STIN/FXRTN . . . . . ST IN/FX RTN channel strip 1–

This setting applies to all four banks.

C Channel selection

Select the MIDI Remote channel for which you want to

make settings. When you click the / buttons at the

left and right of the box, the corresponding name is

displayed in the box at the right. You can change the

name by clicking the button of the right box.

Note

You cannot change the MIDI Remote channel you’re editing

while any of the LEARN buttons (

) are on. You will have to

turn off the LEARN button first.

5 6

MIDI REMOTE screen

MIDI REMOTE

1 2

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 193

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

D BANK SELECT

Of the four banks, select the bank for which you want

to make settings. When you use the A–D buttons to

select a bank, the name of that bank will be displayed in

the field immediately above. You can click the but-

ton at the left to edit the name of the bank.

E CLEAR BANK

This button erases the currently selected bank (all

MIDI messages will be deleted).

F MIDI message

From the top, these fields assign MIDI messages to the

ENCODER [ON] keys, encoders, CH [ON] keys, and

faders. Click the to open the MIDI REMOTE

SETUP window, and input the message as hexadeci-

mal values. You can input the following values.

Hint

When you click a hexadecimal value, the region interpreted as

a MIDI message that includes that value will be displayed in

red.

G LEARN

Use this button to assign a received MIDI message to a

controller. When you turn on one of the four LEARN

buttons, the MIDI message received by the PM5D will

be assigned to the corresponding controller. The

LEARN function uses the MIDI messages received at

the input port specified by the MIDI REMOTE OUT-

PUT PORT in the MIDI SETUP screen.

Hint

• MIDI messages assigned using the LEARN button can be a

maximum of 16 bytes long (the 17th and subsequent bytes

are discarded). If the message is less than 16 bytes long,

END will be immediately after the last data value.

• If a control change is received, the third byte will automati-

cally be replaced by FAD (if the assignment destination is

FADER), ENC (if the assignment destination is ENCODER),

or SW (if the assignment destination is ENCODER ON or

CH ON).

• If more than one message is received while a LEARN but-

ton is on, the last message will be used. (If the status byte

was omitted from the last message, the appropriate status

byte will be added.)

H LATCH

If a specific byte is set to “SW” in a message assigned to

an ENCODER [ON] key or CH [ON] key, use the

LATCH button to select one of the following

behaviors.

• If the LATCH button is on

The on/off status will change each time you press the

key (Latched). If you press the key from the Off state, a

MIDI message with 7F(H) as the SW value will be

transmitted, and when you press the same key once

again a MIDI message with 00(H) as the SW value will

be transmitted.

• If the LATCH button is off

The switch will be on only while you are holding it

down, and will turn off when you release it

(Unlatched). Immediately after you press the key, a

MIDI message with 7F(H) as the SW value will be

transmitted; immediately after you release the key, a

MIDI message with a SW value of 00(H) will be

transmitted.

If a specific byte is set to “ENC” (or “FAD”) in a mes-

sage assigned to an ENCODER [ON] key or a CH

[ON] key, use the LATCH button to select one of the

following behaviors.

• If the LATCH button is on

If you press the key from the Off state, a MIDI message

with the current setting of the encoder (or fader) as the

ENC (or FAD) value will be transmitted, and when you

press the same key once again a MIDI message with a

value of 00(H) as the ENC (or FAD) value will be

transmitted.

• If the LATCH button is off

The moment you press the key, a MIDI message with

the current setting of the encoder (or fader) as the ENC

(or FAD) value will be transmitted; the moment you

release the key, a MIDI message with 00(H) as the ENC

(or FAD) value will be transmitted.

Note

If SW/ENC/FAD is not specified as the last byte of the MIDI

message, turning the key on or off will transmit the same MIDI

message; i.e., the same message is transmitted when the key

goes off.

Value

Available

Assignments

Content

00(H)–

FF(H)

All

The MIDI message that is trans-

mitted (hexadecimal).

END All

Indicates the end of the MIDI

message. When you operate the

corresponding controller, the

MIDI message from the begin-

ning until immediately before

END will be transmitted.

SW All

Indicates the on/off status of the

encoder [ON] key or the channel

[ON] key. A value of 7F(H) is

transmitted when the key turns

on, and a value of 00(H) is trans-

mitted when the key turns off. If

this is assigned to an ENCODER

or FADER, the current value of

the key will be transmitted when

the encoder or fader is operated.

ENC

ENCODER

ON/

ENCODER

Indicates the current position of

the encoder. If assigned to an

ENCODER, a value of 00–7F(H)

is transmitted when the encoder

is operated. If assigned to an

ENCODER [ON] key, the current

value of the encoder is transmit-

ted when the key is switched on.

FAD

CH ON/

FADER

Indicates the current position of

the fader. If assigned to a

FADER, a value of 00–7F(H) is

transmitted when the fader is

operated. If assigned to a CH

[ON] key, the current value of the

fader is transmitted when the key

is switched on.

6 7

MIDI REMOTE function

194 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

Here you can make settings for GPI (General Purpose

Interface) input/output, used to transfer control signals

between the PM5D and an external device.

A GPI IN port

These are the numbers of the GPI IN ports for which

you can make settings.

B GPI IN status

The yellow bar indicates the input signal voltage state

of the corresponding port. If the bar is not shown, the

signal is in the grounded state; if the bar is displayed to

the right edge, the signal is at the high level state. Use

the POLARITY (

3) field to select whether the signal is

active when low or high.

C POLARITY

This selects how GPI IN on/off will be detected. You

can choose Low Active (active when the key is

grounded) or High Active (active when key is open, or

when a high level signal is input).

D FUNCTION

E PARAMETER

These fields indicate the function that is executed when

the corresponding GPI IN port becomes active (or the

function that is controlled by the voltage value being

input from the GPI IN port), and option parameters

for that function.

To edit the settings, click the button at the left to

open the GPI IN PORT ASSIGN window, and select

the function and parameter from the following table.

GPI screen

GPI

1 2

3 4 5

FUNCTION PARAMETER PM5D operation

NO ASSIGN — No assignment

MONITOR

DIMMER ON

Switches the Dimmer

function on/off

SOURCE=

[monitor source

name]

Switches the monitor

source

MONO ON

Switches the monitor sec-

tion [MONO] key on

TALKBACK

LATCH

Switches the Talkback

function on/off (latched

operation)

UNLATCH

Switches the Talkback

function on/off (unlatched

operation)

CH ON-

LATCH

[channel name]

Switches the channel on/

off (latched operation)

CH ON-

UNLATCH

[channel name]

Switches the channel on/

off (unlatched operation)

FADER

LEVEL

[channel name]

Modiﬁes the fader value

(LEVEL parameter)

according to the voltage

SUR-

ROUND PAN

FRONT-REAR

PAN [SEL]

according to the voltage.

LEFT-RIGHT

PAN [SEL]

Modiﬁes the surround pan-

ning (left/right) of the

selected channel accord-

ing to the voltage.

FRONT-REAR

PAN [ODD]

Modiﬁes the surround pan-

ning (front/rear) of the

selected odd-numbered

channel according to the

voltage.

LEFT-RIGHT

PAN [ODD]

Modiﬁes the surround pan-

ning (left/right) of the

selected odd-numbered

channel according to the

voltage.

FRONT-REAR

PAN [EVEN]

Modiﬁes the surround pan-

ning (front/rear) of the

selected even-numbered

channel according to the

voltage.

LEFT-RIGHT

PAN [EVEN]

Modiﬁes the surround pan-

ning (left/right) of the

selected even-numbered

channel according to the

voltage.

USER

DEFINED

KEY FUNC-

TION

[User Deﬁned

key bank / key

number]

While the external input is

active, executes the same

operation as when the

selected User Deﬁned key

is pressed

USER

DEFINED

KEY LED

[User Deﬁned

key bank / key

number]

While the external input is

active, lights the LED of

the selected User Deﬁned

key

PEAK HOLD

—

Switches the Peak Hold

function on/off

OSCILLA-

TOR ON

Switches the Oscillator on/

off

SOLO ON

Switches the Solo func-

tion on/off

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 195

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

❏ GPI IN MONITOR

F GPI IN monitor

The voltage from the GPI IN port selected by the X-

AXIS field (

8) and Y-AXIS field (9) is respectively

indicated by a yellow in the X-axis (horizontal) and

Y-axis (vertical) dimensions of the graph.

The range of voltage variation used to determine the

active/inactive status is shown as a red rectangle.

G CALIBRATION

This button calibrates the range of voltage variation

used by the PM5D to determine active/inactive status,

so that the range will be appropriate for the voltages

being input from the GPI PORT. (For details on using

calibration ➥ p.135)

When you turn this button on, the range of voltage

variation will be temporarily cleared; the range will be

updated every time the GPI IN voltage changes. When

you turn this button off, the range of variation will be

memorized, and this range of variation will subse-

quently be used to determine the active/inactive state.

H X-AXIS

I Y-AXIS

These fields select the GPI IN port for which calibra-

tion will be performed. You can click the /

buttons at left and right to change the port.

If you are using a two-dimensional controller such as a

joystick, specify a port for both the X-axis and Y-axis. If

you want to perform calibration for only one direc-

tion, set one of the ports to “-----.”

J REVERSE

This button inverts the low/high level of the input,

changing the displayed direction of the graph. This is

equivalent to switching the POLARITY (3) of the

selected GPI IN port.

❏ GPI OUT

K GPI OUT port

These are the numbers of the GPI OUT ports for which

you can make settings.

L GPI OUT status

This indicates the state of the output signal for the cor-

responding port. The L/H character indicates whether

the signal level is Low (the output level is grounded) or

High (the output level is high). The background color

is yellow when active, and gray when inactive. Use the

POLARITY (

M) field to select whether the signal is

active when low or high.

M POLARITY

Selects the polarity of the signal that is output when the

GPI OUT port becomes active. You can select either

Low Active (grounded when active) or High Active

(high level when active).

N TEST

This button tests the operation of each GPI OUT port.

While this button is on, the corresponding GPI OUT

port will temporarily become active, and a signal will

be output according to the POLARITY (

M) setting.

O FADER START

Indicates the channel of the fader assigned as a trigger

to each GPI OUT port, and the fader mode (trigger

detection method) of that fader.

To edit the settings, click the button at the left to

open the GPI OUT PORT ASSIGN window, and select

the fader mode and channel. You can select the follow-

ing fader modes.

• FADER START

A control signal (trigger signal) 250 msec long will be

output when the fader of the selected channel moves

from –60 dB or below to exceed –60 dB.

• FADER STOP

A control signal (trigger signal) 250 msec long will be

output when the fader of the selected channel reaches

–∞ dB.

• FADER TALLY

A control signal will be output when the fader of the

selected channel moves from –60 dB or below to

exceed –60 dB. This control signal will be held until the

fader reaches –∞ dB (or until that GPI OUT port

receives a different trigger).

The setting of the GPI screen’s FADER START field is

linked with the GPI-related settings of the FADER

START screen (➥ p.196).

K L

M N O P Q

MIDI REMOTE function

196 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

P USER DEFINED KEYS

This area indicates the User Defined keys that are

assigned as triggers to each GPI OUT port, and their

operations.

To edit the setting, click the button at the left to

open the GPI OUT PORT ASSIGN window; from the

list, select the User Defined key bank (A–D) and num-

ber (1–25), and how the trigger signal will be

transmitted. As the transmission method for the trig-

ger signal, you can select either Latch (switch between

active/inactive each time the key is pressed) or Unlatch

(active only while the key is pressed).

Q TALLY

This area indicates the state of other Tally output func-

tions assigned as triggers to each port. When you

execute the corresponding operation on the PM5D, a

control signal will be output from the corresponding

GPI OUT port. This control signal will be held until

you defeat the above operation (or until that GPI OUT

port receives a different trigger).

To edit the settings, click the button at the left to

open the GPI OUT PORT ASSIGN window, and select

one of the following functions.

Here you can make settings for the Fader Start function

which lets you use input channel faders to control GPI

OUT ports or external devices.

A INPUT CH (Input channel)

This area shows the number and name of the channels

(input channels, ST IN channels) for which you can

make settings. When you click a line to select it, that

line will be highlighted in the center of the list.

B OUTPUT TYPE

C PARAMETER

Indicates the type of signal that will be output when

you operate the corresponding fader, and option

parameters for it. To edit the setting, click the but-

ton at the left of the OUTPUT TYPE field to open the

FADER START ASSIGN window. You can select the

following output types and parameters.

• NO ASSIGN

No assignment.

• GPI

A trigger will be sent to the specified GPI OUT port

according to the fader operation of the corresponding

channel, and a control signal will be output. (The

polarity of the control signal will be as specified by the

settings in the GPI screen.) If this output type is

selected, you can choose from the following two option

parameters.

FADER START . . . GPI OUT port from which the

trigger is sent when the fader

changes from below –60 dB to

exceed –60 dB.

Function PM5D operation

NO ASSIGN No assignment

POWER ON The PM5D’s power is turned on

SOLO ON [SOLO] key is turned on

GPI IN 1 FUNC-

TION

The function assigned to GPI IN port 1

becomes active

GPI IN 2 FUNC-

TION

The function assigned to GPI IN port 2

becomes active

GPI IN 3 FUNC-

TION

The function assigned to GPI IN port 3

becomes active

GPI IN 4 FUNC-

TION

The function assigned to GPI IN port 4

becomes active

PREVIEW ON

SCENE MEMORY section [PREVIEW]

key is turned on

CUE ON [INPUT

ONLY]

Input channel [CUE] key is turned on

CUE ON [DCA

ONLY]

DCA [CUE] key is turned on

CUE ON [OUT-

PUT ONLY]

Output channel [CUE] key is turned on

CUE ON Any [CUE] key is turned on

FADER START screen

FADER START

1 2 3 4

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 197

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

FADER STOP . . . . . GPI OUT port from which the

trigger is sent when the fader

reaches –∞ dB.

Note that the GPI-related settings you make in the

FADER START screen are linked with the FADER

START field of the GPI screen.

For example, if in the FADER START screen you spec-

ify different ports for the FADER START parameter

and FADER STOP parameter of a certain channel, the

FADER START field of the GPI screen will be assigned

to the corresponding channel (Fader Mode= FADER

START/FADER STOP) of those ports. (The opposite

also applies.)

If the same port is specified for the FADER START

parameter and the FADER STOP parameter, the GPI

screen FADER START field will be assigned to the

channel corresponding to that port (Fader Mode=

FADER TALLY). (The opposite is also true.)

•MMC

An MMC command will be sent from the currently-

enabled MIDI port according to the fader operation of

the corresponding channel. (The MIDI transmit port is

selected in the MIDI SETUP screen.)

An MMC PLAY command is transmitted when the

fader changes from below –60 dB to –60 dB or higher,

and an MMC STOP command is transmitted when the

fader reaches –∞ dB.

If this output type is selected, you can use an option

parameter to specify the MMC device ID number (1–

127 or ALL).

•RS422

An RS422 protocol command will be sent from the

RS422 REMOTE connector according to the fader

operation of the corresponding channel.

An RS422 protocol PLAY command is transmitted

when the fader changes from below –60 dB to –60 dB

or higher, and an RS422 protocol STOP command is

transmitted when the fader reaches –∞ dB.

D CLEAR ALL

Clears the Output Type field assignments of all

channels.

⇔

MIDI REMOTE function

198 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

Here you can use MMC/RS422 protocol commands to

remotely control transport/locate operations on a recorder

or other external device from the PM5D.

A MMC DEVICE No.

Indicates the device ID number

of the external device to be con-

trolled via MMC. To change

this setting, click the / but-

tons at left and right to choose

from the range 1–127 or ALL

(applies to all device ID

numbers).

B RS422 DATA FORMAT

Select the format (P2 or

DENON) of the RS422 com-

mands sent from the RS422

REMOTE connector. When you

click this button, a confirma-

tion message will appear.

Note

The RS422 command format you

specify in this screen also applies to

the RS422 commands issued by

the Fader Start function or the User

Defined keys.

Note

DENON format is a set of commands used in devices such as

Denon’s professional CD (DN-C680) and MD (DN-M1050R)

players. On the CD or MD player, set the settings to 9600 bps

and RS422. If you are using DENON format, clicking the

button during Play will enter Pause mode; clicking the

button during Standby will Stop. While stopped, click the

button once again if you want to Standby. Clicking the

button will return to the previous track, and clicking the

button will advance to the next track. Use a D-Sub 9-pin

straight cable to connect the REMOTE RS422 connector to

the device you wish to control using P2 or DENON format.

C Transport

These buttons operate the transport of an external

device. When you click a button, the corresponding

MMC/RS422 command (from the left, REWIND,

FAST FORWARD, STOP, PLAY, REC) will be

transmitted.

There is an indicator above each RS422 transport but-

ton; the indicator will light as follows according to the

status of the external device being controlled.

•P2

• DENON

TRANSPORT screen

TRANSPORT

Playing lit

Fast-forwarding lit

Rewinding lit

Stopped lit

Recording and lit

Playing lit

Paused blinking

Standby lit

Stopped All dark

Recording and lit

Recording paused lit, blinking

5 64

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 199

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

D LOCATE POINT

These buttons correspond to each locate point. Twenty

locate points can be specified for MMC-compatible

devices, and another twenty locate points can be sepa-

rately specified for RS422-compatible devices. When

you click buttons 1–20, an MMC command or RS422

command for moving to that locate point will be

transmitted.

E Time code

This field indicates the time code that is specified for

each locate point. To edit the time code, click the

button located at the left to open the MMC/RS422

LOCATE POINT window, and specify the new time

code in hours/minutes/seconds/frames. (In the case of

DENON format, use track/minute/second/frame units

to specify the value.) You can also use the CAPTURE

button located at the right to capture the time code

being received by the PM5D.

F CAPTURE

This button captures the time code currently being

received by the PM5D, and inputs it in the time code

field. In the case of MMC, the time code source, frame

rate, and offset time can be specified in the EVENT

LIST screen (SCENE function). (➥ p.177) In the case

of RS422, the time data at that moment for the exter-

nal device being controlled will be captured.

Here you can remotely control various functions of a

Yamaha DME series digital mixing engine.

Hint

As of this writing (April 2007), this function can be used with

the DME series models DME64N, DME24N, DME8i-C,

DME8o-C, DME4io-C, DME8i-ES, DME8o-ES and DME4io-

ES. (This function cannot be used with the DME32.)

A Component type selection area

Here you can select the type of DME series component

that you want to control from the PM5D. When you

click the / buttons at the left and right to select the

type of component, the display in the central area of

the screen will change accordingly. The following types

of component can be selected.

• SETUP

Select the port connecting the PM5D and the DME

series unit, and initiate or terminate communication.

• GEQ

Control the DME series unit’s graphic EQ from the

PM5D.

• PEQ

Control the DME series unit’s parametric EQ from the

PM5D.

• CROSS OVER

An internal signal within the DME series unit is divided

into six bands, and the output level, filter slope and

type, and cutoff frequency etc. can be controlled for

each band. This screen also lets you specify the cross-

over frequency at which the bands are divided.

• LONG DELAY

• SHORT DELAY

Control the long delay and short delay functions of the

DME series unit from the PM5D.

• MATRIX

Specify the level of the signals sent from a specific input

of the DME series unit to all outputs, or from all inputs

to a specific output.

• SLOT OUTPUT

For each slot of the DME series unit, specify the out-

put level, delay time, and phase setting of each port.

B Component selection area

From the type of component you selected in 1, select

the component that you want to control.

DME CONTROL screen

541 2 3

MIDI REMOTE function

200 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

C MONITOR

When you click the monitor source select button (@),

the MONITOR POINT SELECT window will appear,

allowing you to select the monitor source for the DME

series. When you turn the MONITOR button on, the

EXTERNAL CUE indicator in the upper part of the

display will turn on, and the monitor signal of the

DME series will be sent to the PM5D’s CUE bus.

Note

If you want to turn the MONITOR button on, you must first

select the same port for the DME series’ monitor output and

the PM5D monitor input. The monitor output of the DME

series unit can be specified in the “Monitor Out” dialog box

accessed from DME Designer via the [Tools] menu

→

[Moni-

tor]. The monitor input of the PM5D unit is specified by

MONITOR PORT in the SETUP area of the DME CONTROL

screen.

D SCENE

This area indicates/selects the scene that will be stored/

recalled on the DME series unit. When you click the /

buttons located at left and right to select a number,

the name of that scene is shown in the field at right.

E STORE/RECALL

These buttons save (overwrite) the settings of the DME

series unit edited in the PM5D’s screen into the scene

selected in the SCENE area, or recall the scene selected

in the SCENE area into the DME.

Note

• When storing a DME scene from the PM5D’s screen, you

can only store by overwriting an existing scene on the DME;

you cannot store the settings as a new scene or edit the

scene name.

• If SETUP is selected, items

, and

are not shown.

F Parameter display area

This area displays the parameters of the currently

selected component. The displayed contents will

depend on the component.

G ASSIGN TO FADERS (DCA fader

assignments)

You can use DCA faders 1–8 to control the parameters

of the component currently shown in the screen.

Note

The parameters that can be assigned to DCA faders will

depend on the component. This function may not be available

for some components.

❏ Connecting the PM5D with a DME

series unit

Various methods for connecting the PM5D with a DME

series unit to transmit and receive audio signals and con-

trol signals are shown below.

Note

If characters other than alphabetical characters and symbols

(e.g., double-byte characters such as Japanese) are used on

the DME series unit in a component name or scene name,

such characters may not be displayed correctly.

1 Bi-directional connection via CobraNet

This connection method uses CobraNet (a format for

transmitting multi-channel audio signals and control sig-

nals over Ethernet). Install a MY-16CII CobraNet card in

the PM5D’s slot, and use an Ethernet cable to connect it to

the DME series. This method allows bi-directional transfer

of audio signals over a single cable. For example, signals

can be sent via the PM5D’s MIX bus to the DME for pro-

cessing, and then returned to a PM5D input channel.

Note

You cannot use AuviTran’s AVY16-ES EtherSound card to

control the DME series from the PM5D.

2 Bi-directional connection using the CASCADE IN/

OUT connectors (DME64N only)

In this connection method, the CASCADE IN connector

and CASCADE OUT connector of the PM5D and the

DME64N are connected to each other, allowing bi-direc-

tional transfer of audio signals.

PM5D

CobraNet

connector

DME series

CobraNet

card

Slot

DME64N

PM5D

CASCADE

OUT connector

CASCADE

OUT connector

CASCADE

IN connector

CASCADE

IN connector

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 201

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

3 Uni-directional connection using the CASCADE IN/

OUT connectors — 1 (DME64N only)

This method is a uni-directional connection that sends

audio signals from the DME64N to the PM5D via its CAS-

CADE IN connector.

4 Uni-directional connection using the CASCADE IN/

OUT connectors — 2 (DME64N only)

This method is a uni-directional connection that sends

audio signals from the PM5D via its CASCADE OUT con-

nector to the DME64N.

Note

When using the CASCADE IN/OUT connectors to make con-

nections, the CASCADE IN/OUT connectors are used as the

connectors, but the settings will be the same as when using

slot input/output. In the CASCADE CONNECTION area of the

MIXER SETUP screen (SYS/W.CLOCK function), you will

need to make settings so that the CASCADE IN connector is

assigned to the SLOT IN port (if using the CASCADE IN con-

nector) or the SLOT OUT port is assigned to the CASCADE

OUT connector (if using the CASCADE OUT connector).

Hint

If desired, you can control the DME series unit from the PM5D

without transmitting or received audio signals. In this case,

simply make one of the connections shown in examples

–

; control signals will be sent from the PM5D to the DME.

5 Connections using the DSP5D

If the PM5D and DSP5D are cascade-connected, install a

MY-16CII CobraNet card in a slot of the DSP5D (machine

#2), and use an Ethernet cable to connect it to the DME

series.

Note

You cannot use AuviTran’s AVY16-ES EtherSound card to

control the DME series from the PM5D.

❏ Procedure for connecting the DSP5D

and DME series

1 Bi-directional connection via the CASCADE IN/

OUT connectors (DME64N only)

This is an example of connecting the CASCADE IN and

CASCADE OUT connectors of the DSP5D and DME64N

respectively, so that audio signals be transferred bi-

directionally.

DME64N

PM5D

CASCADE

IN connector

CASCADE

OUT connector

DME64N

PM5D

CASCADE

OUT connector

CASCADE

IN connector

PM5D

DSP5D

CASCADE IN

DME series

CobraNet connector

CASCADE

OUT connector

CASCADE

OUT connector

CASCADE

IN connector

to CASCADE IN connector

DME64N

DSP5D

CASCADE IN

HUB

CASCADE

OUT connect

CASCADE

IN connector

to CASCADE IN (D-SUB)

connector

CASCADE OUT

(D-SUB) connector

MIDI REMOTE function

202 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

2 Connection using a DCU5D unit

You can use an Ethernet cable to connect the DSP5D and

DME series via a DCU5D digital cabling unit.

Note

The DSP5D must be connected via the CASCADE OUT (RJ-

45) connector.

❏ Initiating communication between the

PM5D and the DME series unit

To select the port used for audio signal transmission/recep-

tion between the PM5D and the DME series unit, and to

initiate communication, proceed as follows.

Connect the PM5D and the DME series unit.

In the DISPLAY ACCESS section, press the

[MIDI/REMOTE] key several times to access the

DME CONTROL screen.

In the component selection area at the upper

left of the screen, select SETUP.

A screen like the following will appear.

The SETUP screen contains the following items.

A CONNECT

This button initiates or terminates the connection

between the PM5D and the DME series unit.

B MIDI PGM CHANGE (MIDI program

change)

If this button is on, a program change message will be

transmitted to the DME via the I/O card or via the

CASCADE IN/OUT connectors when a scene is

recalled on the PM5D. This allows scenes to be recalled

on the DME in tandem with scene recall operations on

the PM5D.

C INPUT PORT

Here you can select the PM5D port that will receive

audio signals from the DME.

D MONITOR PORT

Here you can select the PM5D port that will receive

monitor signals from the DME. Since this monitor sig-

nal is sent to the PM5D’s CUE bus, the DME’s monitor

function can be controlled from the PM5D just like the

PM5D’s own cue function (EXTERNAL CUE

function).

E MIXER SETUP (show the MIXER SETUP

screen)

This button displays the SYS/W.CLOCK function

MIXER SETUP screen.

F OUTPUT PORT

Here you can select the PM5D port that will output

audio signals to the DME.

In the INPUT PORT area

located at the lower left

of the screen, select the

PM5D port that will

receive audio signals from

the DME series unit.

The types of port that can be

selected here will depend on

the port that is currently selected for cascade input

(MIXER SETUP screen CASCADE IN PORT SELECT

field), as follows.

Note

• You cannot switch the cascade input port setting from the

DME CONTROL screen. If necessary, click the MIXER

SETUP button to access the MIXER SETUP screen (SYS/

W.CLOCK function), and change the port you will use for

cascade input.

• Depending on the type of cascade connection, the DSP5D

port will indicate only the items that can be selected: ---,

SLOT1-2, CASCADE IN (D-SUB), or CASCADE OUT (RJ-

45).

In the MONITOR PORT field, select the PM5D

port that will receive monitor signals from the

DME series unit.

The following ports can be selected.

---- . . . . . . . . . . . . . . . . . .No assignment

SLOT1-1–SLOT4-16 . . .The desired port of slot 1–4

CASCADE 1–32 . . . . . . .CASCADE IN ports 1–32

DSP5D

CASCADE IN

HUB

DCU5D

POWER

DME series

CASCADE

OUT connector

CASCADE

IN connector

to CASCADE IN (D-SUB)

connector

CASCADE OUT

(D-SUB) connector

CASCADE OUT

(RJ-45) connector

CASCADE

IN (RJ-45)

connector

1 5

4 6

Setting in the CAS-

CADE IN PORT

SELECT ﬁeld (MIXER

SETUP screen)

Items available in the INPUT

PORT ﬁeld

CASCADE IN ----, SLOT1–SLOT4

SLOT4 ----, CASCADE IN, SLOT1–SLOT3

SLOT3/4 ----, CASCADE IN, SLOT1–SLOT2

SLOT1-4 [CH1-8] ----, CASCADE IN

SLOT1-4 [CH9-16] ----, CASCADE IN

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 203

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

In the OUTPUT PORT field

located in the lower right

of the screen, select the

PM5D port that will trans-

mit audio signals to the

DME.

The types of port that can be

selected here will depend on

the port that is currently selected for cascade output

(MIXER SETUP screen CASCADE OUT PORT

SELECT field), as follows.

Note

• You cannot switch the cascade output port setting from the

DME CONTROL screen. If necessary, click the MIXER

SETUP button to access the MIXER SETUP screen (SYS/

W.CLOCK function), and change the port you will use for

cascade output.

• Depending on the type of cascade connection, the DSP5D

port will indicate only the items that can be selected: ---,

SLOT1-2, CASCADE OUT (D-SUB), or CASCADE OUT

(RJ-45).

If you want scene changes on the PM5D to be

linked with scene changes on the DME series

unit, turn on the MIDI PGM CHANGE button

in the center of the screen.

If the MIDI PGM CHANGE button is on, switching

the scene on the PM5D will cause a program change

message of a number corresponding to that scene to be

sent to the DME.

Hint

• The above program change message is always transmitted

via the I/O card or the CASCADE IN/OUT connector. This is

not affected by MIDI PGM CHANGE or by the MIDI pro-

gram change transmission port or transmission on/off setting

selected in the MIDI SETUP screen.

• The program number assignment for each scene can be

specified in the MIDI PGM CHANGE screen.

To initiate communication between the PM5D

and the DME series unit, click the CONNECT

button to turn it on.

While the CONNECT button is on, parameter opera-

tions and scene store/recall operations on the DME can

be remotely controlled from the PM5D. To terminate

communication, click the CONNECT button once

again to turn it off.

❏ Controlling DME parameters

Here’s how the parameters of the DME series unit can be

controlled from the PM5D. If desired, the changes you

make can be saved in the scene of the DME series unit.

In the DME CONTROL screen, choose SETUP,

and turn on the CONNECT button to initiate

communication.

In the upper left of the screen, use the compo-

nent type / component selection areas to

select the component you want to control.

If a component other than SETUP is selected, internal

parameters of the DME can be controlled from the

PM5D screen. The following illustration is an example

of when the SLOT OUTPUT component is selected.

Use the knobs, sliders, and buttons in the

screen to control the parameters of the DME

series unit.

Knob, slider, and button operation methods are the

same as for the PM5D’s internal parameters. For details

on the parameters that can be operated for each com-

ponent, refer to the owner’s manual of the DME series

unit.

If you want to use DCA faders 1–8 to control

the parameters of the component, click an A–F

button in the ASSIGN TO FADERS area.

When you click a button A–F, the corresponding

parameters will be assigned to DCA faders 1–8, and can

be controlled by the faders. To return to the previous

state, click the DCA button.

Hint

As an alternative to clicking the A–F buttons, you can obtain

the same result by holding down the top panel [SHIFT] key

and pressing the [A]–[F] keys of the FADER MODE section.

If you want to store your changes in a scene of

the DME series unit, use the SCENE field in the

upper right of the screen to select the store-

destination, and click the STORE button.

The edited settings will be stored as a scene in the

DME. To recall this scene, use the SCENE field in the

upper right of the screen to select the scene, and click

the RECALL button.

Note

When storing a DME scene from the PM5D’s screen, you can

only store by overwriting an existing scene on the DME; you

cannot store the settings as a new scene or edit the scene

name.

Hint

For a system in which only the DSP5D and DME are con-

nected, use DSP5D Editor to specify the DSP5D port that will

be connected to the DME.

You can select the following connectors/slots for each port.

• INPUT PORT

CASCADE IN (D-SUB), SLOT1, SLOT2, CASCADE OUT

(RJ-45)

• OUTPUT PORT

CASCADE OUT (D-SUB), SLOT1, SLOT2, CASCADE OUT

(RJ-45)

Setting in the CAS-

CADE OUT PORT

SELECT ﬁeld (MIXER

SETUP screen)

Items available in the OUTPUT

PORT ﬁeld

CASCADE OUT ----, SLOT1–SLOT4

SLOT3/4

----, SLOT1–SLOT4, CASCADE

OUT

SLOT1-4 [CH1-8]

SLOT1-4 [CH9-16]

UTILITY function

204 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

UTILITY function

Preference settings for the PM5D are divided into two

screens.

For the DSP5D

A STORE/RECALL

These buttons let you turn on/off options related to

scene store/recall operations. You can select the follow-

ing options.

• AUTO STORE

Turns the Auto Store function on/off. If this button is

on, pressing the [STORE] button (SCENE MEMORY

section) of the panel twice in succession will store the

current scene in the currently selected scene number.

• LINKED LIBRARY PROTECTION

If this button is on, you will be unable to overwrite or

delete library items that are linked to a protected scene.

This option prevents a protected scene from being

modified by having an associated library item edited.

• USE NUMERIC-KEYPAD

If this button is on, the numeric keypad of a PS/2 key-

board connected to the KEYBOARD connector (or a

numeric keypad connected to the KEYBOARD con-

nector) can be used to specify the scene number

directly.

• STORE CONFIRMATION

• RECALL CONFIRMATION

If these buttons are on, a confirmation message will

appear when you perform a Store or Recall operation

respectively.

B PATCH

These buttons let you turn on/off options related to

patch operations. You can select the following options.

• PATCH CONFIRMATION

If this button is on, a confirmation message will appear

when you edit an input patch or output patch.

• STEAL PATCH CONFIRMATION

If this button is on, a confirmation message will appear

when you edit an input patch or output patch item that

is already patched.

C GATE/COMP (Gate / Compressor)

These buttons let you turn on/off options related to

gating and compression.

• GR METER ON/OFF LINK

If this button is on, the GR meter will not show the

reduction amount for gates/compressors that are cur-

rently off.

PREFERENCE 1/2 screens

REFERENCE 1

PREFERENCE 2

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 205

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

D DCA MUTE TARGET

This specifies whether the DCA [MUTE] key will mute

the send to the MIX bus when the send-source to the

MIX bus is PRE FADER. If you specify “POST ONLY,”

the PRE FADER signal will not be muted. If you spec-

ify “PRE & POST,” it will be muted regardless of the

send-source position.

E METER SECTION

Here you can set the following meter-related options.

• FOLLOW INPUT LAYER

This option lets you specify how the [CH 1-24]/[CH

25-48] keys (INPUT channel strip) and [STIN 1-4]/

[FXRTN 1-4] keys will select the layer that is shown by

the meters in the center of the panel and the meters in

the upper right of the panel. Click the / buttons at

left and right to make your choice.

OFF . . . . . . . . Operating the [CH 1-24]/[CH 25-48]

keys will not affect the content shown

by the meters in the center of the

panel. Pressing the [STIN 1-4]/

[FXRTN 1-4] keys will not affect the

content shown by the meters in the

upper right of the panel.

SAME . . . . . . . When you press the [CH 1-24] or

[CH 25-48] key, the corresponding

layer will be shown by the meters in

the center of the panel (if an input

channel is selected in the meter sec-

tion). When you press the [STIN 1-4]

or [FXRTN 1-4] key, the correspond-

ing layer will be shown by the meters

in the upper right of the panel.

ALTERNATIVE . . . When you press the [CH 1-24]

or [CH 25-48] key, the opposite

layer will be shown by the

meters in the center of the panel

(if an input channel is selected

in the meter section). When you

press the [STIN 1-4] or

[FXRTN 1-4] key, the opposite

layer will be shown by the

meters in the upper right of the

panel.

Note

• If this is set to SAME or ALTERNATIVE, the meters in the

center of the panel and the meters in the upper right can be

switched independently.

• If the selected layer is switched from the panel, the layer

shown by the meters will also change. However if you switch

the METER SECTION field in the constantly-displayed area

in the upper part of the screen, the layer selected on the

panel will not change.

• FOLLOW MIX MASTER MODE

If this button is on, pressing the MIX section [MIX

MASTER] key will cause the meters in the center of the

panel and the meters in the upper right of the panel to

show the MIX/MATRIX channel levels. Press the MIX

section [MIX SEND] key to return to the original input

channel level display.

F PANEL OPERATION

Here you can set the following options for panel

operation.

• AUTO CHANNEL SELECT

This specifies whether the corresponding channel will

be selected when you operate a channel’s [ON] key,

fader, or encoder. INPUT CH (input channels) and

OUTPUT CH (output channels) can be turned on/off

separately.

• AUTO DISPLAY

For each of the following items, you can individually

specify whether the related screen will automatically

appear when you use the SELECTED CHANNEL sec-

tion to operate a specific parameter. The following

table shows the parameters corresponding to each but-

ton and the screen that will appear.

Button name

Corresponding

parameters

Screen that appears

Input channel head

amp gain

INPUT HA/INSERT

function screens

PHASE/ATT

Input channel

phase/attenuator

INPUT EQ function ø/

ATT screen

EQUALIZER

EQ-related param-

eters

INPUT EQ/OUTPUT

EQ function EQ

PARAM screen

DYNAMICS

Gate/compressor-

related parameters

INPUT GATE/COMP

function or OUTPUT

COMP function GATE

PARAM or COMP

PARAM screen

DELAY

Delay-related

parameters

INPUT DELAY/OUT-

PUT DELAY function

screens

DCA/MUTE/

SAFE

DCA group / Mute

group / Recall safe-

related parameters

INPUT DCA/GROUP

function or OUTPUT

DCA/GROUP func-

tion DCA GROUP

ASSIGN, MUTE

GROUP ASSIGN or

RECALL SAFE

screen

TO MIX/STE-

REO

TO MIX/TO STE-

REO-related

parameters

PAN/ROUTING func-

tion CH to MIX screen

or SURR PARAM

screen, or MATRIX/ST

function MATRIX/ST

ROUTING screen

TO MATRIX

Send level to

MATRIX bus

MATRIX/ST function

MATRIX/ST ROUT-

ING screen

UTILITY function

206 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

• MAKE PAIR ON PANEL

If this button is on, you can use the [SEL] keys to set/

defeat pairing. In Horizontal Pair mode, you can set/

defeat pairing by simultaneously pressing the [SEL]

keys of two pairable channels. In Vertical Pair mode,

you can set/defeat pairing by holding down the

[SHIFT] key and pressing the [SEL] key of one of the

channels. (For more about pair modes ➥ p.53)

• USE ENCODER-ON AS +48V

If this button is on, the ENCODER [ON] key located

above the encoder will turn the phantom power

(+48V) on/off when HA (head amp input sensitivity) is

selected as the encoder mode.

• DCA/MUTE FLASH INDICATE

If this button is on, the DCA [MUTE] key LED and the

DCA assign LED for channels belonging to that DCA

group will blink when you turn on a DCA [MUTE] key

(DCA section).

• MIX MINUS CONFIRMATION

If this button is on, a confirmation message will appear

when you execute the Mix Minus setting (hold down

the [SEL] key of an input channel and press the [SEL]

key of a MIX channel) from the panel.

• SCENE UP/DOWN KEY

This specifies what the SCENE MEMORY [π]/[†]

keys will do when pressed in the SCENE screen. You

can choose one of the following two operations.

SCENE +1/–1 . . . . . Pressing the SCENE MEMORY

[π] key will select the next

highest-numbered scene, and

pressing the SCENE MEMORY

[†] key will select the next low-

est-numbered scene. (Key

presses will increment/decre-

ment the scene number.)

LIST UP/DOWN . . Pressing the SCENE MEMORY

[π] key will scroll the list

upward, and pressing the

SCENE MEMORY [†] key will

scroll the list downward.

(Key presses will scroll the list

upward/downward.)

• LIST ORDER

This specifies the order in which scene memories and

library items will appear in the screen.

NORMAL . . . . . . . . Show the list in ascending

numerical order.

REVERSE . . . . . . . . Show the list in descending

numerical order.

• ATT OPERATION ON PANEL

If this button is on, you will be unable to use the panel

encoders to operate the attenuator.

• MIX SEL/ENCODER MODE LINK

If this button is on, using the panel [SEL] keys or on-

screen operations to select MIX channels 1–24 will

select the MIX SEND SELECT [1]–[24] keys of the

FADER FLIP ENCODER MODE section in tandem. In

the same way, pressing MIX SEND SELECT [1]–[24]

keys will select MIX channels 1–24.

❏ PREFERENCE screen 2

G BRIGHTNESS

Here you can make settings for the brightness of the

panel LED and LCD displays.

• PANEL UNITY POINT

If this button is on, LEDs corresponding to a specific

reference value (e.g., 0 dB or CENTER) will light more

brightly than usual. However, this is valid only if

PANEL BRIGHTNESS is set to 5 or less.

• PANEL ASSISTANCE

If this button is on, even LEDs that should be off will

stay dimly lit so that you can tell their location even in

a dark environment. However, this is valid only if

PANEL BRIGHTNESS is set to 5 or less.

• PANEL BRIGHTNESS

This adjusts the brightness of all panel LEDs in a range

of 1–8.

• LCD BRIGHTNESS

You can adjust the brightness of the LCD display in a

three-step range: HIGH, MID, or LOW.

• LCD BACK LIGHT

You can adjust the brightness of the LCD display back-

light in a two-step range: HIGH or LOW.

H TRACK PAD/MOUSE

Here you can make settings for the built-in track pad

or a PS/2 mouse connected to the MOUSE connector.

• TRACK PAD TAPPING

This enables/disables the Tapping function (a function

that lets you perform the track pad left-click operation

by tapping quickly on the track pad).

• MOVING SPEED

This selects the speed at which the cursor in the screen

will move when you operate the built-in track pad or a

PS/2 mouse connected to the MOUSE connector.

Choose one of three speeds; FAST, MID, or SLOW.

I SCREEN TIPS

• SHOW SCREEN TIPS

If this button is on, moving the cursor onto an item in

the screen and waiting for a short time will (in some

cases) display a “screen tip” reminding you of the oper-

ation. The screen tip is displayed when you open the

JOB SELECT window by holding down the [SHIFT]

key and pressing the [ENTER] key, or when you need

to press the [ENTER] key to finalize an edited value.

OUTPUT

MASTER

MIX/MATRIX chan-

nel output level

OUTPUT VIEW func-

tion FADER VIEW

screen

Button name

Corresponding

parameters

Screen that appears

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 207

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

J UPPER PART DISPLAY

These buttons select the item that is shown in the cen-

ter right (to the right of the scene memory indication)

of the upper part of the display (the constantly dis-

played area).

• PRESENT TIME

Indicates the present time.

• TIME CODE

Indicates the internal time code being generated by the

PM5D, or the time code being received from an exter-

nal device. This is the same as the time code shown in

the SCENE function EVENT LIST screen.

• CASCADE/Fs

Indicates the master/slave status when using a cascade

connection, and the sampling frequency at which the

PM5D system is currently operating.

Hint

You can also cycle through these choices by clicking in this

display section.

K NAME DISPLAY ([NAME] indicator display)

Choose one of the following as the content that will be

shown by the [NAME] indicators of the INPUT chan-

nel strip and DCA strip.

• NAME

The indicators will show the names assigned to the

input channels / DCA groups in the NAME screen

(INPUT PATCH function). (➥ p.282)

• PORT

For input channels, the indicators will show the name

of the currently assigned port. For DCA groups, the

indicators will show the ID number.

•ID

For both input channels and DCA groups, the indica-

tors will show the fixed ID number.

L WARNING DISPLAY

Here you can select whether a warning will be dis-

played when the following problems occur.

• TIME CODE DROP

When time code (LTC, MTC) being received from an

external device is dropped.

• DIGITAL I/O ERROR

When a DIO error is detected.

• MIDI I/O ERROR

When a MIDI error is detected.

M CHANNEL NAME NUMERIC DISPLAY

• ENCODER VALUE

When you operate an encoder (pan setting), the name

display will switch to indicating that value.

• FADER VALUE

When you operate a fader, the name display will switch

to indicating that value.

N SOFTWARE VERSION

This indicates the version of the unit’s operating soft-

ware (firmware).

O BATTERY

This indicates the voltage of the internal battery.

P POWER SUPPLY (DSP5D only)

This indicates the status of the DSP5D’s power supply.

This will indicate “INTERNAL” if the DSP5D is oper-

ating on its internal power supply, or “EXTERNAL” if

it is operating on the PW800W external power supply.

Q INTERNAL CLOCK

This indicates the year/month/day (DATE) and time

(TIME) of the internal clock.

If you want to change the setting, click the SET button.

R BACKGROUND COLOR

This specifies the screen background color for each

machine. If the PM5D and DSP5D are cascade-con-

nected, having a different background color will make

it easier to distinguish the machines when you switch

between them for control.

S NETWORK (DSP5D only)

Here you can make network settings used when the

DSP5D’s [NETWORK] connector is connected to your

computer via an Ethernet cable (➥ p.159).

Q R S

UTILITY function

208 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

Here you can assign functions to the User Defined keys

(USER DEFINED [1]–[25] keys).

A BANK

Select a bank A–D (groups of functions assigned to the

User Defined keys).

B CLEAR BANK

Clears the currently selected bank.

C List

This area lists the functions and option parameters

assigned to the User Defined keys in the currently

selected bank.

To edit the settings, click the button at the left to

open the USER DEFINED KEY ASSIGN window, and

select the function and parameter from the following

table.

USER DEFINE screen

USER DEFINE

FUNCTION PARAMETER 1 PARAMETER 2 Explanation

NO ASSIGN — — No assignment

SCENE

INC RECALL — Recall the scene of the next existing number.

DEC RECALL — Recall the scene of the previous existing number.

DIRECT RECALL SCENE #000–#500 Directly recall the scene of the speciﬁed number

EVENT LIST

TIME CODE [RTN TO START]

—

The same functions as the RETURN TO START TIME,

STOP, and PLAY buttons displayed when INTERNAL is

selected as the time code source in the EVENT LIST screen

TIME CODE [STOP]

TIME CODE [PLAY]

TIME CODE [INSERT]

The same function as the TIME CODE INSERT button in the

EVENT LIST screen

AUTO CAPTURE ON

The same function as the AUTO CAPTURE button in the

EVENT LIST screen

DIRECT EVENT RECALL EVENT #000–#999

Recall the speciﬁed event registered in the EVENT LIST

screen

NEXT EVENT RECALL

—

Recall the next-numbered event

PREV EVENT RECALL Recall the previous-numbered event

ENABLE/DISABLE

Switch the ENABLE button and DISABLE button in the

EVENT LIST screen

ENABLE [ALL MANUAL]/DIS-

ABLE

Switch the ENABLE [ALL MANUAL] button and DISABLE

button in the EVENT LIST screen

EFFECT LIBRARY

DIRECT RECALL → EFFECT

1–8

INC RECALL Recall the next-numbered library item into effect 1–8

DEC RECALL Recall the previous-numbered library item into effect 1–8

LIBRARY #001–#199 Recall the library item of the speciﬁed number into effect 1–8

EFFECT BYPASS EFFECT 1–EFFECT 8 BYPASS ON Bypass the speciﬁed effect

INPUT CH LIBRARY

DIRECT RECALL

LIBRARY #000–#199

Recall the library item of the speciﬁed number into the

selected channel/GEQ module

OUTPUT CH

LIBRARY

GATE LIBRARY

LIBRARY #001–#199

COMP LIBRARY

INPUT EQ LIBRARY

OUTPUT EQ

LIBRARY

INPUT PATCH

LIBRARY

LIBRARY #00–#99

OUTPUT PATCH

LIBRARY

HA LIBRARY

LIBRARY #000–#199

GEQ LIBRARY DIRECT RECALL → GEQ 1–20

TRACKING RECALL

ENABLE/DISABLE

—

The same function as the ENABLED/DISABLED button in

the TRACKING RECALL screen

OFFSET LOCK

The same function as the OFFSET LOCK button in the

TRACKING RECALL screen

SELECTED CH ON

Switch the Tracking Recall function on/off for the currently

selected channel

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 209

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

TALKBACK ASSIGN

SELECTED CH ASSIGN —

When an output channel is selected, turn talkback transmis-

sion on/off for that channel

DIRECT ASSIGN

MIX 1–24, MATRIX 1–8,

STEREO A L/R, STE-

REO B L/R

Send the talkback signal to the speciﬁed output channel

MONITOR

DIRECT ASSIGN MIX 1–24, MATRIX 1–8 Monitor the desired MIX/MATRIX channel

DIMMER ON — Switch on the monitor dimmer function

TAP TEMPO

CURRENT PAGE

—

Control the Tap Tempo function in the displayed screen

EFFECT 1–EFFECT 8 Control the Tap Tempo function of the speciﬁed effect

ALL EFFECTS

Control the Tap Tempo function of all effects that have a

TEMPO parameter

SURROUND PAN GRAB

SELECTED CH, ODD

CH, EVEN CH

Use a joystick assigned to GPI to begin controlling the sur-

round pan of the corresponding channel

NAME DISPLAY

NAME → PORT → ID —

Each time you press the key, the [NAME] indicator for each

fader will cycle through the channel name → port name → ID

(channel number)

UNLATCH

The [NAME] indicator for each fader will show the ID (chan-

nel number) only while you hold down the key

PORT

The [NAME] indicator for each fader will show the port name

only while you hold down the key

NAME

The [NAME] indicator for each fader will show the channel

name only while you hold down the key

PAGE CHANGE

PAGE BACK

—

Display the screen that you used immediately prior to the

current screen

PAGE FORWARD

Display the screen that you used immediately after the cur-

rent screen

PAGE BOOKMARK

Memorize the currently selected screen (hold down the key

for two seconds or longer), or display the last-memorized

screen (press and release the key within two seconds)

GEQ PARAM PAGE GEQ 1–20 Display the GEQ PARAM screen

EFFECT PARAM PAGE EFFECT 1–8 Display the EFFECT PARAM screen

NEXT TAB

—

Display the next screen within the currently selected function

PREVIOUS TAB

Display the previous screen within the currently selected

function

LAYER SNAPSHOT — —

Memorize the state of the layer assigned to the panel (hold

down the key for two seconds or longer), or display the last-

memorized layer (press and release the key within two sec-

onds)

DIRECT RECALL/

MUTE MASTER

MODE CHANGE

LATCH

Switch the function of the SCENE MEMORY [1]–[8] keys

(DIRECT RECALL / MUTE MASTER) each time you press

the User Deﬁned key

UNLATCH

The SCENE MEMORY [1]–[8] keys will function as DIRECT

RECALL while you hold down the User Deﬁned key

USER DEFINED KEY

BANK

NEXT BANK

—

Switch to the next bank of User Deﬁned key assignments

PREVIOUS BANK

Switch to the previous bank of User Deﬁned key assign-

ments

DIRECT SELECT BANK A–D Switch to the desired bank of User Deﬁned key assignments

MIDI DIRECT OUT

MIDI NOTE C-2–G 8

When you press the key, transmit a note-on message with

the speciﬁed note number and a velocity of 127 When you

release the key, transmit a note-on message of the same

note number with a velocity of 0 (= note-off)

MIDI PGM CHANGE 1–128

When you press the key, transmit a program change mes-

sage with the speciﬁed number

MIDI CTRL CHANGE 0–119

When you press the key, transmit a control change message

with the speciﬁed control number and a value of 127 When

you release the key, transmit a control change message of

the same control number with a value of 0

MACHINE CONTROL

SET LOCATION, RS-422 REC,

RS-422 PLAY, RS-422 STOP,

RS-422 FF, RS-422 REW, RS-

422 LOCATE 1–20

—

Transmit the speciﬁed RS422/MMC command from the

RS422 REMOTE connector or the currently-valid MIDI port

(the SET LOCATION command is common to RS422 and

MMC)

MMC REC, MMC PLAY, MMC

STOP, MMC FF, MMC REW,

MMC LOCATE 1–20

MMC ID= 1–127, ALL

GPI OUT CONTROL PORT 1–12

LATCH

Switch the speciﬁed GPI OUT port between active/inactive

each time you press the key

UNLATCH

Switch the speciﬁed GPI OUT port to inactive while you hold

down the key

PM5D EDITOR CON-

TROL

*5 *5

Switch windows in PM5D Editor on a PC

FUNCTION PARAMETER 1 PARAMETER 2 Explanation

UTILITY function

210 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

Note

During PREVIEW mode, the following USER DEFINE functions that affect internal signal processing are disabled;

EVENT LIST, TALKBACK ASSIGN, MONITOR, MIDI DIRECT OUT, MACHINE CONTROL, and GPI OUT CONTROL.

SET NOMINAL

LEVEL

——

If you hold down this key and press the [SEL] key, the fader

of that channel will be set to nominal level. (While you hold

down this key, only the [SEL] keys of channels not at nominal

level will light.) Alternatively, you can set the level to nominal

level by moving the cursor to an on-screen knob (level, EQ

gain) or fader, and then pressing the [ENTER] key while

holding down this key.

SET DEFAULT

VALUE

——

If you move the cursor to an on-screen knob or fader, and

then press the [ENTER] key while holding down this key, the

control will return to its default value

ENCODER MODE

KEY

PA N

—

Same function as the [PAN] key in the top panel ENCODER

MODE section

GAIN/ATT

Same function as the [GAIN/ATT] key in the top panel

ENCODER MODE section

ALT LAYER

Same function as the [ALT LAYER] key in the top panel

ENCODER MODE section

MIX SEND 1–24

Same function as the MIX SEND SELECT [1]--[24] keys in

the top panel ENCODER MODE section

FADER FLIP —

Same function as the [FLIP] key in the top panel FADER

FLIP section

SELECTED CH INSERT ON/OFF — Turns insert on/off for the selected channel

STEREO STRIP

SECTION

STEREO A, STEREO B MONITOR, CUE

Select either STEREO A/B channels, Monitor, or Cue as the

function controlled by the STEREO A/B channel strip's STE-

REO fader and [ON] key

Dark: Monitor or CUE is enabled

Lit: STEREO A/B channels are enabled

DSP5D CONTROL

MACHINE SELECT

#1(PM5D), #2(DSP5D),

#3(DSP5D)

Select the PM5D or DSP5D (#2 or #3) as the machine that

will be controlled by panel operations (Lit if the speciﬁed

machine is selected)

CH STRIP LAYER DIRECT

#1(PM5D) CH1-24,

#1(PM5D) CH25-48,

#2(DSP5D) CH1-24,

#2(DSP5D) CH25-48,

#3(DSP5D) CH1-24,

#3(DSP5D) CH24-48,

#1(PM5D) STIN1-4,

#1(PM5D) FX RTN1-4,

#2(DSP5D) STIN1-4,

#2(DSP5D) FX RTN1-4,

#3(DSP5D) STIN1-4,

#3(DSP5D) FX RTN1-4

Switch the INPUT channel strip or ST IN/FX RTN channel

strip to a layer of the desired machine (Lit if the speciﬁed

layer is selected)

*1. The corresponding channel will be selected in the DEFINE ﬁeld of the MONITOR screen, and the monitor source will switch to

DEFINE.

*2. The LED will light for User Deﬁned keys for which a screen has been memorized. The column in the right of the list in the USER

DEFINE screen shows the name of the memorized screen.

*3. Layers that can be memorized include the following items.

- The layer selected in the INPUT channel strip (CH 1-24, CH 25-48, MIDI REMOTE)

- The layer selected in the ST IN/FX RTN channel strip (ST IN 1-4, FX RTN 1-4, MIDI REMOTE)

- The layer shown by the DCA channel strip (DCA, A–F, GEQ)

- If the DCA channel strip is controlling GEQ, the GEQ module number and band

- The encoder mode selected by ENCODER MODE (SEND, PAN, HA, ATT, ALT)

- The FADER FLIP status

- The currently selected MIX send

- The mode selected in the MIX section (MIX SEND, MIX MASTER)

- The source selected in the METER section (CH 1-24 ST IN, CH 25-48 ST IN, MIX/MATRIX)

*4. The output port and MIDI channel can be speciﬁed in the MIDI SETUP screen.

*5. This parameter speciﬁes the PM5D Editor window that you want to control. If the speciﬁed window is closed or inactive, the window

will be opened and made active. If the speciﬁed window is already open and active, the window will be closed.

FUNCTION PARAMETER 1 PARAMETER 2 Explanation

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 211

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

Here you can save PM5D scenes and library data on a

memory card inserted in the MEMORY CARD slot. This

cannot be used while in PREVIEW mode.

Hint

If the PM5D and DSP5D are cascade-connected, the settings

of each machine can be consecutively saved by a single

operation.

A MODE

Choose one of the following as the mode in which files

will be saved: BASIC, ADVANCED, CSV EXPORT.

The left side of the screen will change according to the

mode you select.

❏ BASIC mode

In BASIC mode you can save all scene memory and library

data (or just a selected portion of data) to a card. If BASIC

is selected, the left side of the screen will show the items

listed in the following table.

B Select the items to save

Choose one of the following to specify the data that will

be saved.

SAVE screen

SAVE

Button Content

ALL DATA

All items of each type, and the con-

tents of the current scene

SCENE MEMORY Contents of scene memory

LINKED LIBRARY

Libraries linked to the scene (avail-

able only if the SCENE MEMORY

button is on)

HA Contents of the HA library

INPUT PATCH Contents of the input patch library

OUTPUT PATCH Contents of the output patch library

INPUT CH Contents of the input channel library

OUTPUT CH Contents of the output channel library

INPUT EQ Contents of the input EQ library

OUTPUT EQ Contents of the output EQ library

GATE Contents of the gate library

COMP Contents of the compressor library

EFFECT Contents of the effect library

GEQ Contents of the GEQ library

SETUP Various settings not saved in a scene

USER DEFINED

KEY

User Deﬁned key settings

DCA FADER MODE Fader mode settings

MIDI REMOTE MIDI remote settings

MIDI PGM TABLE

Contents of the list in the MIDI PGM

CHANGE screen

MIDI CTRL TABLE

Contents of the list in the MIDI CTRL

CHANGE screen

EVENT LIST

Contents of the list in the EVENT

LIST screen

BASIC button

UTILITY function

212 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

If the SCENE MEMORY, HA, INPUT PATCH, or

OUTPUT PATCH button is on, you can use the box at

the right to specify the starting number and ending

number of the scenes or library items that will be saved.

Hint

If the specified range of numbers includes empty scenes or

library items, the correspondingly-numbered scenes or library

items will be empty when that data is loaded.

C TOTAL SIZE

Indicates the file size of the currently selected item(s)

(common to all modes).

❏ ADVANCED mode

In this mode you can select either scene memory or a

library, specify a starting number and ending number, and

save the specified range of data on a card. If desired, you

can also specify that the starting number be shifted for-

ward or backward when the data is saved. If ADVANCED

is selected, the left side of the screen will show the follow-

ing items.

D CATEGORY

Indicates the category of data that is selected for sav-

ing; scene memories or library data. Click the /

buttons at left and right to change the category.

E SOURCE (save-source numbers)

This area shows the starting and ending number (and

the corresponding scene names or library titles) of the

scene memories or library items that will be saved on

the card. Click the / buttons at the left and right of

each box to change the number.

F DESTINATION (save-destination number)

This area shows the starting and ending number (and

the corresponding scene names or library titles) with

which the data will be saved on the card. If you want to

save the data to the card with a different range of num-

bers, click the / buttons at the left and right of the

starting number box. (The value in the ending number

box will change automatically as the starting number is

edited.)

❏ CSV EXPORT mode

In this mode you can select items such as scene memory or

library titles, or channel names, and write them to a card as

a separate CSV format file for each item. If CSV EXPORT

is selected, the left side of the screen will show the items

listed in the following table.

Note

If a DSP5D (machine #2 or #3) is selected as the target of

control, CSV files can’t be written. If you need to write a CSV

file, please use DSP5D Editor.

Starting number Ending number

ADVANCED button

011

012

013

014

015

AAA

BBB

CCC

DDD

EEE

001

002

003

004

005

006

AAA

BBB

CCC

DDD

EEE

FFF

➠

Memory card

Starting

number

Ending

number

CSV EXPORT button

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 213

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

G LIBRARY TITLE

H CHANNEL NAME

From the following table, select the parameters that will

be written (e.g., library title, channel name).

Hint

Files saved in CSV format can be edited using a word proces-

sor or spreadsheet software on a computer, and loaded back

into the PM5D. However be aware that it will not be possible

to reload the file back into the PM5D if you change the syn-

tax, file format, or file name.

If you use Microsoft Excel to edit these files, use the Data

menu to import the CSV file, and use the Text File Wizard to

delete the character string quotation ("). (If you fail to do so,

symbols such as “–” and “+” will not be displayed correctly.)

I SET ALL

Selects all LIBRARY TITLE / CHANNEL NAME items.

J CLEAR ALL

De-selects all items.

K FILE PATH

Indicates the directory (folder) that is currently selected

on the memory card inserted in the MEMORY CARD

slot, and the location of the file. (The directory name is

delineated by “\” characters.)

L SCAN

This scans the directory that is currently selected on the

memory card, and displays the contents in the file list

(

M).

M File list

This area shows the files/directories contained in the

current directory. The currently selected file/directory

is always shown in the middle line. (The TYPE and

DATE SIZE fields will be highlighted.)

The list is divided into four columns; FILE NAME,

TYPE, DATE/SIZE, and COMMENT. (To see the

COMMENT field, use the scroll bar to scroll the list

toward the right.)

The headings at the top of each column of the list also

function as buttons to sort the list. When you click

these buttons, the list will be sorted in ascending or

descending order for that item. The text of the cur-

rently selected button will change to red, and an arrow

indicating ascending (↑) or descending (↓) order will

appear.

These columns display the following content.

• FILE NAME

These are the names of the files/directories saved in the

currently selected directory. If a lower directory is

selected, you can move to that directory by clicking the

directory name shown in this column.

Button Content

LIBRARY

TITLE

SCENE MEMORY Scene memory names

HA HA library titles

INPUT PATCH Input patch library titles

OUTPUT PATCH Output patch library titles

INPUT CH

Input channel library

titles

OUTPUT CH

Output channel library

titles

INPUT EQ Input EQ library titles

OUTPUT EQ Output EQ library titles

GATE Gate library titles

COMP Compressor library titles

EFFECT Effect library titles

GEQ GEQ library titles

CHANNEL

NAME

INPUT 1-48 Input channel names

ST IN ST IN channel names

FX RTN FX RTN channel names

DCA DCA names

PATCH

INPUT PATCH

Input patch connection

status

OUTPUT PATCH

Output patch connection

status

P Q R N

UTILITY function

214 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

If a higher directory is selected, this column will show a

“. .” symbol. You can click this symbol to return to that

directory.

• TYPE

This indicates the type of data that is saved. In the case

of a directory, this column will indicate [DIR]. Data

that cannot be used by the PM5D is indicated as

UNKNOWN.

• DATE / SIZE

This shows the date on which the file was last saved,

and its size. In the case of a directory, only the date of

creation is displayed.

• COMMENT

This displays comments (up to 32 characters) stored

for the files on the memory card. To create or edit a

comment, click the COMMENT field of the file

selected in the list to open the FILE COMMENT EDIT

window.

N Number of files / Free area

This displays the number of files and directories in the

current directory, and the free area on the memory

card.

Note

A maximum of 99 files and directories can be displayed in the

file list. If there are more than 99, a blinking message of “Too

Many Files” will be displayed. In this case, please delete

unneeded files or move files to another directory.

O SAVE

This saves the data selected in the left side of the screen

to the currently selected directory. When you click this

button, the FILE NAME EDIT window will appear,

allowing you to assign a filename of up to eight charac-

ters and save the file.

Note

• If an identically-named file exists in that directory, a mes-

sage will warn you that you will be overwriting the file. If you

don’t want to overwrite the existing file, you can either

change the filename or select a different directory in which to

save the file.

• When you execute the Save operation in CSV EXPORT

mode, a new directory will be created within the current

directory of the memory card, and a CSV file for each

selected item will be created in the new directory.

• The name of the CSV file is fixed for each type of data, and

cannot be changed. The newly created directory will have

the name you specified when saving.

P RENAME

This button lets you rename the currently selected file

or directory. When you click this button, the FILE

NAME EDIT window will appear, allowing you to edit

the name.

Q MAKE DIR (Make directory)

This button creates a new sub-directory within the cur-

rently selected directory. When you click this button,

the DIR NAME EDIT popup window will appear,

allowing you to specify a name for the new directory.

R DELETE

This button deletes the currently selected file or direc-

tory. When you click this button, the FILE DELETE

window will appear, asking you to confirm the

deletion.

Note

•A deleted file cannot be recovered.

• If you attempt to delete a directory that contains files, a

warning message will appear, and the operation cannot be

executed. Before deleting a directory, you must first delete

any files it contains.

Note

• As memory cards, the PM5D can use either PCMCIA

Type II flash ATA cards or CompactFlash media inserted in

a PC card adaptor (power supply voltage of 3.3V/5V in

either case). Operation is not guaranteed for any other type

of media.

• Normally, the above cards are sold in an already-formatted

state, so formatting will not be necessary. If you need to for-

mat a card, use a computer or other external device to

format the card in FAT16 format.

➠ ➠

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 215

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

In this screen, scene or library data from a memory card

inserted in the MEMORY CARD can be loaded into the

PM5D. This cannot be used while in PREVIEW mode.

A FILE PATH

Indicates the location of the directory (folder) or file

that is currently selected on the memory card. (The

directory name is delineated by “\” characters.)

B SCAN

This scans the directory that is currently selected on the

memory card, and displays the contents in the file list

(

3).

C File list

This area shows the files/directories contained in the

current directory. The currently selected file/directory

is always shown in the middle line. (The TYPE and

DATE SIZE fields will be highlighted.)

The list is divided into four columns; FILE NAME,

TYPE, DATE/SIZE, and COMMENT. (To see the

COMMENT field, use the scroll bar to scroll the list

toward the right.) The contents of each column are the

same as in the SAVE screen (➥ p.213).

D Mode

Here you can select the mode in which files will be

loaded. If a file other than CSV is selected in the file list,

you will be able to select BASIC mode or ADVANCED

mode. (The CSV button will be grayed-out and

unavailable.)

If a CSV file or directory is selected in the file list, CSV

IMPORT mode will be selected automatically. (The

BASIC and ADVANCED buttons will be grayed-out

and unavailable.)

The right side of the screen will change as follows

according to the currently selected mode.

❏ BASIC mode

In BASIC mode you can load all scene memory and

library data (or just a selected portion of data) from a

card. If BASIC is selected, the right side of the screen

will show the following items.

E Select the data to be loaded

Here you can select the data that will be loaded. The

contents of each item are the same as in BASIC mode

of the SAVE screen (➥ p.211). However, the items that

can be selected will depend on the currently selected

file. Buttons for items that cannot be loaded will be

grayed-out and unavailable.

If the SCENE MEMORY, HA, INPUT PATCH, or

OUTPUT PATCH button is on, you restrict the scenes

or library items that will be loaded by using the box at

the right to specify the starting number and ending

number.

Hint

If the data saved on the card includes empty scenes or library

items, the corresponding scenes or library items will be empty

when the data is loaded.

LOAD screen

LOAD

1 2

BASIC button

UTILITY function

216 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

F LOAD

This button loads the data selected in the left side of the

screen into the parameters you specify. When you click

this button, a message will ask you to confirm the Load

operation. (This is common to all modes.)

Note

If cascade connection is enabled, you can’t execute the load

operation.

❏ ADVANCED mode

In this mode you can select either scene memory or a

library, specify a starting number and ending number, and

load the specified range of data from the card.

G CATEGORY

This indicates the type of data (scene memory or

library) saved in the currently selected file.

H SOURCE (load-source)

This area shows the starting and ending number (and

the corresponding scene names or library titles) of the

scene memories or library items that will be loaded

from the card. Click the / buttons at the left and

right of each box to change the number.

I DESTINATION (load-destination)

If you’ve changed the starting number of the load-des-

tination, this area shows the starting and ending

number (and the corresponding scene names or library

titles) of the PM5D’s internal scene memories or

library items into which the data selected in the

SOURCE area will be loaded. To edit the setting, click

the / buttons located at the left and right of the

starting number box. (The ending number value will

change automatically as you edit the starting number.)

Hint

• Even if you’ve selected data that was saved in BASIC mode,

you can switch to ADVANCED mode and load only specific

numbers.

• However, an exception is that if the selected data was saved

as ALL DATA or SCENE MEMORY+LINKED LIBRARY in

BASIC mode, the ADVANCED button will be grayed-out,

and you will not be able to switch to ADVANCED mode.

Note

You cannot load from a memory card if LOAD LOCK is turned

on in the UTILITY function SECURITY screen.

❏ CSV IMPORT mode

If a CSV file or directory is selected, CSV IMPORT

mode will be selected automatically. The selected CSV

file (or CSV files in the selected directory) will be

searched, and the following items will appear in the

right of the screen.

Note

If a DSP5D (machine #2 or #3) is selected as the target of

control, CSV files can’t be loaded. If you need to load a CSV

file, please use DSP5D Editor.

J LIBRARY TITLE

K CHANNEL NAME

Use these buttons to select the data you want to load

(e.g., library titles or channel names). (The contents of

each item are the same as in the SAVE screen.)

However, you will only be able to select items that

match the CSV file (or the CSV files in the directory)

selected in the list for loading. The buttons for other

items will be grayed-out and unavailable.

L SET ALL

This button selects all available items for loading.

M CLEAR ALL

De-selects all items.

Note

Note that the screen will automatically switch to CSV IMPORT

mode even if the directory selected in the list does not contain

an appropriate CSV file. (In this case, all buttons will be

grayed-out.)

ADVANCED button

002

003

004

005

006

BBB

CCC

DDD

EEE

FFF

011

012

013

014

BBB

CCC

DDD

EEE

➠

Memory card

Starting

number

Ending

number

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 217

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

Here you can assign the desired input channels / output

channels to the eight faders in the DCA section of the

panel. Here you can also assign the machine, INPUT chan-

nel layer, and ST IN/FX RTN layer that will be switched in

tandem with the FADER MODE.

A MACHINE ID

This assigns a machine ID number (#1–#3) that will be

the target of panel operations. If you select “STAY” the

machine will not change.

B INPUT

This assigns the layer that will be operated by the

INPUT channel strip. You can select 1–24 or 25–48. If

you select “STAY” the layer will not change.

C 1–8 (DCA faders 1–8)

Here you can assign the channel that will be operated

by each fader. You can select CH 1–48, STIN1L–

STIN4R, FXRTN1L–FXRTN4R, MIX1–24,

MATRIX1–8, DCA1–8, MONITOR LEVEL, or CUE

LEVEL of each machine. If you select “STAY” the fad-

ers will not change. If you select “----,” the faders will

be disabled.

D ST IN/FX RTN

This assigns the layer that will be operated by the ST

IN/FX RTN channel strip. You can select either ST IN

or FX RTN of each machine. If you select “STAY” the

machine will not change.

E FADER MODE

Indicates the currently selected fader mode (layer A–F,

DCA). You can also click the buttons to switch the

fader mode directly. The machine, INPUT channel

strip, DCA faders, and ST IN/FX RTN channel strip

will change.

F Faders 1–8

The parameter assigned to each fader of the DCA fader

section is shown here. This will depend on the cur-

rently selected fader mode. You can also operate the

fader directly by dragging it upward or downward.

G STEREO A/STEREO B

This selects the function that will be operated by the

STEREO faders and STEREO [ON] keys of the STE-

REO A/B channel strip. You can select ST A/B,

MONITOR, or CUE.

Hint

Settings

–

and

will not change until you press the

ENTER key to confirm.

FADER ASSIGN screen

FADER ASSIGN

1 2 4 53

UTILITY function

218 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

In this screen you can prohibit console operation (Console

Lock), prohibit editing for specific parameters (Parameter

Lock) or disabling file loading (Load Lock). Two pass-

words of differing levels can be specified to allow locking

and unlocking.

A SYSTEM PASSWORD

This is a permanent password (maximum of eight

characters) for the entire system. The password you

specify here is valid for the PARAMETER LOCK but-

ton (

2) and for the CONSOLE LOCK button (4).

However, you can perform the Lock operation even

without specifying a password.

If no password has been specified, this box will indi-

cate “--FREE--”. If a password has been specified,

asterisks (*) will be displayed to represent the charac-

ters of the password.

To set or change the password, click the button to

open the SYSTEM PASSWORD CHANGE window.

When setting the password for the first time, you will

input the same password twice for confirmation. To

change the password, you will input both the old pass-

word and the new password. By specifying a blank

entry as the new password, you can restore the state to

a condition in which no password has been set.

Note

The system password is remembered even when the power is

turned off. This means that if you forget the password, you will

be unable to defeat Parameter Lock or Console Lock except

by initializing the entire memory of the PM5D (

➥

p.160).

Please be careful not to lose the system password.

B PARAMETER LOCK

This button sets/defeats Parameter Lock for the param-

eters selected in the LOCK PARAMETER SELECT area

(

5). If not even one parameter is selected, these but-

tons will be grayed-out and cannot be turned on. If the

system password has been set, clicking this button will

open the SYSTEM PASSWORD CHECK window,

where you will need to input the system password.

C LOAD LOCK

This button disables file load operations. If the system

password has been set, clicking this button will open

the SYSTEM PASSWORD CHECK window, where

you will need to input the system password. If this but-

ton is on, synchronization with PM5D Editor/DSP5D

Editor can occur only from this unit to PM5D Editor/

DSP5D Editor (not in the opposite direction).

D CONSOLE LOCK

This button locks the console operations. If the system

password has been set, clicking this button will open

the SYSTEM PASSWORD CHECK window, where

you will need to input the system password.

E LOCK PARAMETER SELECT

If the PARAMETER LOCK button (2) is on, parame-

ters for which editing will be disabled can be selected

from the following table. As long as the PARAMETER

LOCK button (

2) is on, these parameters cannot be

edited.

Note

If you turn on the RECALL LOCK button, the specified param-

eters will also be unaffected by scene or library recall

operations.

SECURITY screen

SECURITY

SYSTEM CONFIGU-

RATION

Changes to the settings of the

MIXER SETUP screen and the CAS-

CADE screen

WORD CLOCK

SETUP

Changes in the word clock setting

DITHER Changes in dither-related settings

INPUT PATCH

Changes to the input patch (and

NAME) settings

OUTPUT PATCH Changes to the output patch settings

INPUT CH ON/OFF Input channel on/off operations

OUTPUT CH ON/

OFF

Output channel on/off operations

MIX TO ST ON/OFF

MIX channel [TO STEREO] key

operations

DCA MUTE ON

DCA [MUTE] key On operations

(Off operations are not included)

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 219

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

F CONSOLE PASSWORD

This is a temporary password (maximum of eight char-

acters) that is separate from the system password. The

password you specify here is valid for the CONSOLE

LOCK button (

7). The method for setting or chang-

ing the password is the same as for the system

password.

Hint

The Console Password is cleared when the PM5D’s power is

turned off, and will return to the unset state (the box will indi-

cate “--FREE--”).

G CONSOLE LOCK

This button locks the console operations. If the con-

sole password has been set, clicking this button will

open the CONSOLE PASSWORD CHECK window,

where you will need to input the console password.

SYS/W.CLOCK function

Here you can select the word clock on which the PM5D

will operate. You can also view and edit settings for cards

installed in slots 1–4.

A MASTER CLOCK SELECT

As the master clock to use, you can select the internal

clock or an external clock input from a connector or

slot. This setting determines the sampling frequency at

which the PM5D will operate. You can select the fol-

lowing items.

6 7

Display Content

INT 96k

The PM5D’s internal clock

(sampling rate= 96 kHz)

INT 88.2k

The PM5D’s internal clock

(sampling rate= 88.2 kHz)

INT 48 k

The PM5D’s internal clock

(sampling rate= 48 kHz)

INT 44.1 k

The PM5D’s internal clock

(sampling rate= 44.1 kHz)

W.CLOCK IN

The word clock supplied from the rear panel

WORD CLOCK IN connector

CASCADE IN

The word clock supplied via the CASCADE

IN connector from another cascade-con-

nected PM5D

2TR IN D1

The clock data of the digital audio signal

supplied from 2TR IN DIGITAL connector 1

2TR IN D2

The clock data of the digital audio signal

supplied from 2TR IN DIGITAL connector 2

2TR IN D3

The clock data of the digital audio signal

supplied from 2TR IN DIGITAL connector 3

SLOT 1–4

The clock data of the digital audio signal

supplied via a digital I/O card in slot 1–4

(selectable in two-channel units)

WORD CLOCK screen

WORD CLOCK

SYS/W.CLOCK function

220 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

Note

• For the DSP5D, you cannot select 2TR IN D1–D3 or SLOT

3–4. For CASCADE IN, you can choose either the D-sub 68-

pin connector or the RJ-45 connector.

• If you make cascade or other connections using the

DCU5D’s CASCADE OUT (RJ-45) connector, it will not be

possible to synchronize to the word clock from the DCU5D’s

CASCADE OUT (D-sub) connector. In this case, you’ll need

to provide a separate connection for the word clock.

The operational status of each clock is shown by the

color of the symbol at the left of each button. Each

color has the following significance.

• LOCK (blue)

This indicates that a clock synchronized with the

source selected in (

2) is being input. If an external

device is connected to the corresponding connector or

slot, input/output is occurring normally between that

device and the PM5D. If the sampling frequency is

close, this status may be displayed even if not

synchronized.

• UNLOCK (red)

A valid clock is not being input. If an external device is

connected to the corresponding connector, input/out-

put cannot occur correctly between that device and the

PM5D.

• LOCK, BUT NOT SYNC’ED (orange)

A valid clock is being input, but is not synchronized

with the clock source selected in (

2). If an external

device is connected to the corresponding connector,

input/output cannot occur correctly between that

device and the PM5D.

• UNKNOWN (yellow)

This indicates that the clock status cannot be detected

because no external device is connected or because

there is no valid clock input. You will be able to select

this connector/slot, but successful synchronization can-

not occur until a valid connection is established.

• SRC ON (green)

This is a special status only for SLOT 1–4 and 2TR IN

2TR IN D1–3, indicating that the corresponding chan-

nel’s SRC (Sampling Rate Converter) is enabled. This

means that even if the signal is not synchronized, nor-

mal input/output with the PM5D is occurring.

Note

• Noise may occur at the output jacks when the word clock

setting is changed. In order to protect your speaker system,

be sure to turn down the power amp output before changing

the word clock setting.

• If you attempt to select a channel whose SRC is on as the

word clock master, a message will appear, warning you that

the sampling rate converter will be disabled.

B Fs (Sampling frequency)

This indicates the sampling frequency at which the

PM5D is operating. This will indicate “UNLOCKED”

while synchronization is lost (such as immediately after

switching the master clock).

C Slot number / Card type

This area shows the type of digital I/O card installed in

slots 1–4.

D INPUT FORMAT (Input signal format)

E OUTPUT FORMAT (Output signal format)

Select one of the following as the method by which sig-

nals will be exchanged with a digital I/O card installed

in the slot when the PM5D is operating at a high sam-

pling rate (88.2/96 kHz).

• SINGLE

This setting allows transmission/reception of the nor-

mal number of channels when existing equipment that

operates at 44.1/48 kHz is connected. The sampling

rate will be converted for each channel of the digital I/

O card, and transmitted/received at half the sampling

frequency (44.1/48 kHz) of the PM5D. (This setting

can be selected only for slots in which a digital I/O card

that does not support 96 kHz is installed.)

• DOUBLE SPEED

This setting allows high sampling rate audio signals to

be transmitted/received without change when equip-

ment that operates at a high sampling rate (88.2/96

kHz) is connected. (This setting can be connected only

for slots in which a digital I/O card that supports 96

kHz is installed.)

• DOUBLE CHANNEL

This setting allows high sampling rate (88.2/96 kHz)

audio signals to be handled when existing equipment

that operates at 44.1/48 kHz is connected. Two chan-

nels of signals at half the PM5D’s sampling frequency

(44.1/48 kHz) are transmitted/received together as a

high sampling rate monaural signal. (The number of

usable channels will be half.)

F FREQUENCY (Sampling frequency)

This indicates the sampling frequency of the signal

being input to each channel of the digital I/O card, in

sets of two channels.

G SRC (Sampling Rate Converter)

This button switches the Sampling Rate Converter on/

off, in sets of two channels. This is available only for

slots in which a digital I/O card with a built-in sam-

pling rate converter is installed.

H EMPHASIS STATUS

This indicates whether emphasis is applied to the input

signal, in sets of two channels. This is available only for

slots in which a digital I/O card is installed.

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 221

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

Here you can make settings that apply to the entire PM5D

system.

A +48V MASTER (DSP5D only)

This is the master phantom power (+48V) switch for

INPUT jacks 1–48 and ST IN jacks 1–4. If this switch is

off, the +48V button shown in the display will be

disabled.

B VIRTUAL SOUNDCHECK

This temporarily switches the input signals without

affecting the scene memory (input patching). For

example, this allows you to perform a sound check

using pre-recorded material played back by a DAW

connected to a slot, instead of the analog input mate-

rial received via the INPUT jacks. When you click the

button located at the left, the VIRTUAL SOUND-

CHECK SETUP window will appear, allowing you to

assign a replacement port for each port. To enable

these settings, click the ON/OFF button located at the

right.

For each port, you can specify a port that will be substi-

tuted virtually. You cannot assign the same port to more

than one port. If you assign a previously-assigned port

to a different port, the patch will be turned off (shown in

gray) for the port whose assignment was taken away. If a

slot is exchanged with the CASCADE IN connector, the

cascade bus number will be displayed in black on a yel-

low background in the slot port number display area. In

the example shown above, slots 1 and 2 are assigned to

AD IN 1–32, so you’ll be able to perform a sound check

using pre-recorded audio received at slots 1 and 2

instead of the analog inputs to the INPUT jacks.

By clicking the PRESET button, you can return the set-

tings of the VIRTUAL SOUNDCHECK SETUP

window to their factory-set state.

C PAIR MODE

Select one of the following two methods by which

input channels will be paired.

• HORIZONTAL PAIR

If this button is on, input channels of adjacent num-

bers (1/2, 3/4 ...) will be paired.

• VERTICAL PAIR

If this button is on, input channels of different layers

that share the same fader (1/25, 2/26 ...) will be paired.

This setting lets you use the faders of the INPUT chan-

nel strip to control up to 24 pairs (48 channels).

Hint

The graphic below the buttons will change according to the

pair mode you select.

When you switch from horizontal pair mode to verti-

cal pair mode, new numbers will be assigned to the

input channels as follows.

Channel 1 → no change

Channel 2 → Channel 25

Channel 3 → Channel 2

Channel 4 → Channel 26

Channel 47 → Channel 24

Channel 48 → no change

(If you again switch back to horizontal pair mode, the

channels will return to their previous number.) How-

ever, please note that this simply means the input

channel that was previously called “channel 2” is now

called “channel 25”; the name and parameter settings

of that channel have not changed.

In the various screens of the display (except for the

TRACKING RECALL screen and the FADER VIEW

screen), switching the pair mode will only change the

displayed numbers; the arrangement of the input chan-

nels will not change.

D PAN NOMINAL POSITION

Here you can specify whether a signal will be at nomi-

nal level when panned to center, or at nominal level

when panned far left or far right. Choose one of the fol-

lowing two settings. You can choose independently for

monaural channels and paired channels.

• CENTER

The signal will be at nominal level (+0 dB) when

panned to the center, and will rise +3 dB when panned

to far left or far right.

•L ↔ R

The signal will be at nominal level (+0 dB) when

panned to far left or far right, and will decrease

–3 dB when panned to the center.

Hint

The current setting is also shown by the graph below the

buttons.

MIXER SETUP screen

MIXER SETUP

SYS/W.CLOCK function

222 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

E BUS SETUP

This area indicates the MIX bus mode (VARI/FIXED)

for every two adjacent odd-numbered/even-numbered

MIX buses. You can edit the setting by clicking the /

buttons at the left and right.

F STEREO B

Select one of the following two choices to specify how

the STEREO B bus will function.

• USE AS STEREO BUS

If this button is on, the STEREO B bus will function as

a conventional stereo bus; the same signal as the STE-

REO A bus will be sent to it.

• USE AS CENTER BUS

If this button is on, the STEREO B bus will function as

the CENTER bus of LCR mode. When you turn this

on, the CENTER bus output signal will be added to the

L/R channels of the STEREO A bus, allowing LCR

playback (three-channel playback). (The monitor sig-

nal will also be played back from the three MONITOR

OUT connectors L/C/R.

Note

If the USE AS STEREO BUS button is on, LCR mode is

disabled.

G SURROUND BUS ALLOCATION

Choose which of the following two ranges of MIX bus

will be used as surround buses.

MIX 1-8 . . . . . MIX bus 1–8

MIX 9-16 . . . . MIX bus 9–16

H SURROUND MODE

Choose one of the following as the surround mode

when using the Surround Pan function (➥ p.142).

• STEREO

This is conventional stereo mode.

• 3-1ch

This mode uses four channels: L (front left), C (front

center), R (front right), and S (surround).

• 5.1ch

This mode uses six channels: L (front left), C (front

center), R (front right), Ls (rear left), Rs (rear right),

and LFE (subwoofer).

• 6.1ch

This mode uses seven channels: 5.1ch with the addi-

tion of Bs (rear center).

Hint

The graphic below the buttons will change according to the

mode you select.

587

(front left)

(front center)

(front right)

(surround)

LFE

(subwoofer)

(rear left)

(rear right)

(front left)

(front center)

(front right)

LFE

(subwoofer)

(rear left)

(rear right)

(front left)

(front center)

(front right)

(rear center)

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 223

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

I TYPE SELECT

Click this window to access the CASCADE TYPE

SELECT window, where you can select the type of cas-

cade connection.

Note

• Set the cascade connection type to match the actual con-

nection. If it does not match, the system will not operate

correctly.

• The head margin of the buses that can be cascaded may

change according to the type of cascade connection.

In the CASCADE CONNECTION area of the MIXER

SETUP screen, the color of the route (heavy arrow)

between machines indicate the type or status of the

route as follows.

Blue: A route that sums the buses of each

machine

Yellow: A route that returns the final signal of the

cascaded buses

Red: A route that is not connected correctly

Gray: A route for which it cannot be determined

whether the connection is correct

This means that in order for the cascade connection to

work properly, you must make connections and set-

tings so that no routes are displayed in red or gray. The

numbers shown above or below each route indicate the

number of each machine included in the signals that

flow through each route.

• PM5D-PM5D

This system directly cascade-connects PM5D units. A

maximum of four PM5D units can be connected. Use

L–Q to specify the details of the cascade connection.

• PM5D-DCU5D — DCU5D-PM5D

This system cascade-connects two DCU5D units

between the PM5D units in order to extend the dis-

tance of the cascade connection. A maximum of two

PM5D units can be connected. Use

L–Q to specify

the details of the cascade connection.

• PM5D-DSP5D

This system cascade-connects one DSP5D unit to the

PM5D, expanding the number of input channels to 96

monaural input channels.

• PM5D-DCU5D — DSP5D

This system cascade-connects one DCU5D and one

DSP5D to the PM5D, adding 48 remotely located

monaural inputs.

• PM5D-DSP5D-DSP5D

This system cascade-connects two DSP5D units to the

PM5D, expanding the number of input channels to

144 monaural input channels.

• PM5D-DCU5D — DSP5D-DSP5D

This system cascade-connects one DCU5D and two

DSP5D units to the PM5D, adding 96 remotely located

monaural inputs.

SYS/W.CLOCK function

224 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

• PM5D-DCU5D — DSP5D-DCU5D — DSP5D

This system cascade-connects two DCU5D units and

two DSP5D units to the PM5D, adding two sets of 48

remotely located monaural inputs.

J CASCADE ENABLED/DISABLED

Turns the Cascade function on/off.

Note

• If you edit the parameters (

–

) included in CASCADE

CONNECTION or power-cycle the unit, the cascade func-

tion will return to the Off state.

• If word clock becomes unlocked while machines are syn-

chronized (before cascade connection is enabled), the

operation of each machine may become unstable. If this

occurs, please power-cycle each machine.

• This setting will not be loaded for PM5D firmware V2.0 and

later.

K DME CONTROL

This button accesses the DME CONTROL screen

(➥ p.199).

The following items

L–Q are shown only if you select

“PM5D-PM5D” or “PM5D-DCU5D — DCU5D-

PM5D”as the cascade-connection type. If you select a cas-

cade-connection that includes a DSP5D, the same settings

are made automatically, and the settings will be only for

viewing.

L CASCADE FROM (Source when cascade-

connected)

Select one of the following as the external device that is

sending audio signals to the PM5D via a cascade

connection.

M CASCADE IN PORT SELECT

Select one of the following as the port that will receive

the audio signals from the cascade-connected device.

Hint

• If you select a choice other than CASCADE IN, the signal

from the slot will be assigned to the cascade input, and the

signal from the CASCADE IN connector will be assigned to

the corresponding slot input.

• The signal assigned from the CASCADE IN connector to the

slot input can be used as a patch source in the IN PATCH

screen.

• CASCADE IN

Up to 30 channels of audio signals can be received

from another PM5D via the rear panel CASCADE IN

connector. If PM5D is selected as the cascade source

(

L), control signals for parameter linkage will also be

transmitted and received.

• SLOT 4

Up to 16 channels of audio signals can be received via

input channels 1–16 of an I/O card installed in slot 4 of

the rear panel. If you choose this setting, the signals

from the CASCADE IN connector (channels 1–16) will

be assigned to channels 1–16 of the SLOT IN 4 port

instead.

Display Source device

Available cas-

cade input port

Parame-

ter linkage

— Cascade disabled

CASCADE IN,

SLOT 3/4,

SLOT 1-4

[CH1-8], SLOT

1-4 [CH9-16]

Not

possible

PM5D or

PM5D+

DCU5D

another PM5D CASCADE IN Possible

NL QP

M O K

DM2000

/02R96

Yamaha DM2000

or 02R96

CASCADE IN

Not

possible

MIXER

[30BUS]

A mixer other than

the above (maxi-

mum 30 bus)

SLOT 3/4,

SLOT 1-4

[CH1-8], SLOT

1-4 [CH9-16]

MIXER

[16BUS]

A mixer other than

the above (maxi-

mum 16 bus)

SLOT 4

*1. Linked parameters are speciﬁed in the CASCADE

screen.

Display Source device

Available cas-

cade input port

Parame-

ter linkage

CASCADE IN

CH 1-16

SLOT 4

SLOT IN 1 (CH 1–16)

SLOT IN 2 (CH 1–16)

SLOT IN 3 (CH 1–16)

CH 1-16

SLOT 1-3

SLOT IN 4 (CH 1–16)

CASCADE IN

CH 1-16

16 channels

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 225

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

• SLOT 3/4

Up to 30 channels of audio signals can be received via

input channels 1–16 of I/O cards installed in slots 3 and

4. (Since channels 15/16 of SLOT 4 are not used, only

30 channels are actually available.) If you choose this

setting, the signals from the CASCADE IN connector

(channels 1–32) will be assigned to channels 1–16 of

the SLOT IN 3/4 ports instead.

• SLOT 1-4 [CH1-8]

Up to 30 channels of audio signals can be received via

input channels 1–8 of I/O cards installed in slots 1–4.

(Since channels 7/8 of SLOT 4 are not used, only 30

channels are actually available.) If you choose this set-

ting, the signals from the CASCADE IN connector

(channels 1–32) will be assigned to channels 1–8 of the

SLOT IN 1–4 ports instead.

• SLOT 1-4 [CH9-16]

Up to 30 channels of audio signals can be received via

input channels 9–16 of I/O cards installed in slots 1–4.

(Since channels 15/16 of SLOT 4 are not used, only 30

channels are actually available.) If you choose this set-

ting, the signals from the CASCADE IN connector

(channels 1–32) will be assigned to channels 9–16 of

the SLOT IN 1–4 ports instead.

N CASCADE TO (Transmission destination

when cascade-connected)

As the external device to which audio signals will be

transmitted and control signals exchanged over the cas-

cade connection, you can select either PM5D/

PM5D+DCU5D (i.e., a different PM5D unit) or “----”

(transmission disabled).

O CASCADE OUT PORT SOURCE SELECT

Select one of the following as the signal source that will

be output from the CASCADE OUT connector.

Hint

If you select a setting other than CASCADE OUT, the same

signals will be output both to the corresponding slots and to

the CASCADE OUT connector.

• CASCADE OUT

The audio signals sent by the cascade function will be

output from the CASCADE OUT connector. If PM5D

is selected as the transmission destination (

N), con-

trol signals for parameter linkage will also be

transmitted and received. The type of signals that are

output can be selected in the CASCADE screen.

• SLOT 3/4

The same audio signals (up to 32 channels) as are out-

put from output channels 1–16 of slots 3/4 will be

output in parallel from the CASCADE OUT connector.

• SLOT 1-4 [CH1-8]

The same audio signals (up to 32 channels) that are

output from output channels 1–8 of slots 1–4 will also

be output in parallel from the CASCADE OUT

connector.

• SLOT 1-4 [CH9-16]

The same audio signals (up to 32 channels) that are

output from output channels 9–16 of slots 1–4 will also

be output in parallel from the CASCADE OUT

connector.

P CASCADE MODE

Choose one of the following two modes of operation

when multiple PM5D units are cascade-connected.

• MASTER

If the Cascade function is enabled, control signals will

be sent to an external PM5D.

• SLAVE

If the Cascade function is enabled, control signals will

be received from an external PM5D.

Q BI-DIRECTION (Bi-directional

communication)

When multiple PM5D units are connected, this button

selects whether they will mix each other’s audio signals.

Set the Cascade mode and the BI-DIRECTION button

according to the type of cascade connection, as dis-

cussed below.

If you cascade-connect two PM5D units in a “ring”

topology (i.e., connect the CASCADE IN connector of

each unit to the OUT connector of the other unit), set

the cascade mode to MASTER on one unit and SLAVE

on the other unit. Turn the BI-DIRECTION button

On for both units.

CASCADE IN

CH 1-16

SLOT 3/4

CH 1-16

SLOT 1/2

CASCADE IN

CH 1-32

SLOT IN 1 (CH 1–16)

SLOT IN 2 (CH 1–16)

SLOT IN 3 (CH 1–16)

SLOT IN 4 (CH 1–16)

30 channels

32 channels

CASCADE IN

CH 1-8

SLOT 1-4

CH 9-16

SLOT 1-4

SLOT IN 1–4 (CH 9–16)

SLOT IN 1–4 (CH 1–8)

CASCADE IN

CH 1-32

30 channels

32 channels

CASCADE IN

CH 9-16

SLOT 1-4

CH 1-8

SLOT 1-4

SLOT IN 1–4 (CH 1–8)

SLOT IN 1–4 (CH 9–16)

CASCADE IN

CH 1-32

30 channels

32 channels

PM5D A

CASCADE

OUT

CASCADE

OUT

PM5D B

CASCADE MODE= MASTER

BI-DIRECTION= ON

CASCADE MODE= SLAVE

BI-DIRECTION= ON

Audio signals of

A+B

Audio signals of

A+B

(Cascade master) (Cascade slave)

SYS/W.CLOCK function

226 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

In this state, the SLAVE unit will follow when you

operate the MASTER unit. The same mix will be out-

put from both PM5D units.

If you daisy-chain two to four PM5D units (i.e., con-

nect the first unit’s CASCADE OUT → second unit’s

CASCADE IN, and the second unit’s CASCADE OUT

→ third unit’s CASCADE IN. Up to four units can be

connected.), set the PM5D located last in the chain to

MASTER, and the remaining PM5D units to SLAVE.

Turn the BI-DIRECTION button Off for all units.

In this state, the SLAVE units will follow when you

operate the MASTER unit. The final mix of all signals

will be output from the PM5D that is connected last in

the chain.

Here you can make various settings related to cascade

connection.

A CASCADE ENABLED/DISABLED

Enables/disables cascade connection.

B CASCADE LINK

Here you can select the operations and parameters that

will be linked when multiple PM5D units are cascade-

connected. You can select the following items.

• SCENE RECALL

Scene recall operations / Recall undo operations

• SCENE STORE/EDIT

Scene store operations, store undo operations, title

editing, sorting

• CUE/SOLO LOGIC

Cue/Solo operations (however, all Cue settings are

cleared when linking occurs)

• DIMMER ON/OFF

Dimmer effect (including talkback dimmer)

• PAGE CHANGE

Switching the display screen

CASCADE MODE= SLAVE

BI-DIRECTION= OFF

PM5D C

CASCADE MODE= MASTER

BI-DIRECTION= OFF

PM5D D

CASCADE MODE= SLAVE

BI-DIRECTION= OFF

PM5D A

CASCADE

OUT

CASCADE

OUT

CASCADE

OUT

CASCADE

OUT

CASCADE MODE= SLAVE

BI-DIRECTION= OFF

PM5D B

(Cascade slave)

Audio signals of

A+B+C+D

(Cascade slave)

(Cascade master)

Audio signals of

A+B+C

Audio signals of

A+B

Audio signals of A

CASCADE screen

CASCADE

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 227

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

• DCA FADER MODE

Switching the mode of the top panel FADER MODE

section

• ENCODER MODE

Switching the mode of the top panel ENCODER

MODE section

• PANEL/LCD BRIGHTNESS

BRIGHTNESS settings in the PREFERENCE 2 screen

(UTILITY function)

• INPUT METER POINT/OUTPUT METER POINT/

PEAK HOLD

Input channel / output channel metering point selec-

tion, and peak hold on/off

• DCA LEVEL/MUTE

DCA group 1–8 level, name, [CUE] key on/off opera-

tions, and [MUTE] key on/off operations

Hint

DCA and MUTE parameter values will be linked the instant

Link is turned on. Other parameters will be linked for the first

time only when that parameter is operated after Link is turned

on.

• MUTE MASTER

Mute group 1–8 on/off

Hint

• For details on the actual procedure of cascade-connecting

multiple PM5D/DSP5D units, refer to p.153.

• In the case of a system that is cascade-connected to the

DSP5D, the system will always operate as though the CAS-

CADE LINK area’s LINK button is on; this setting cannot be

changed. Other operations may also be linked.

• To enable cascade link, you must turn on linking for the cor-

responding parameters on the other cascade-connected

PM5D units as well.

• You can also turn linking off for the master PM5D. For

example if you’ve cascade-connected multiple PM5D units,

you can (for example) make settings so that DCA 1 is linked

only between the master and the second unit, DCA 2 is

linked for all PM5D units, and DCA 3 is linked only between

the second unit and third unit.

C CASCADE IN SOURCE (Cascade IN source I/

O assignment view)

Here you can view and select the signals that are sent to

the PM5D/DSP5D’s internal buses from the cascade-

connected external device. The type of signals received

will depend on the selection in the CASCADE FROM

field of the MIXER SETUP screen (SYS/W.CLOCK

function.)

D CASCADE IN ON/OFF

For each of the PM5D/DSP5D’s internal buses, you can

specify whether signals from the cascade master will be

input.

E PARAM LINK (parameter link)

For each pair of adjacent odd-numbered/even-num-

bered channels, this specifies whether the PM5D/

DSP5D’s channel parameters will be linked to output

the identical signal.

F CASCADE OUT ON/OFF

For each of the PM5D/DSP5D’s internal buses, you can

specify whether signals will be output to the cascade

slave.

43 5 6

External device selected in the

CASCADE FROM ﬁeld

Destina-

tion bus

PM5D/

DSP5D

DM2000/

02R96

MIXER

[30BUS]

MIXER

[16BUS]

MIX 1 BUS 1

SLOT4- 1 MIX 1

MIX 2 BUS 2 SLOT4-2 MIX 2

MIX 3 BUS 3 SLOT4-3 MIX 3

MIX 4 BUS 4 SLOT4-4 MIX 4

MIX 5 BUS 5 SLOT4-5 MIX 5

MIX 6 BUS 6 SLOT4-6 MIX 6

MIX 7 BUS 7 SLOT4-7 MIX 7

MIX 8 BUS 8 SLOT4-8 MIX 8

MIX 9 AUX 1 SLOT4-9 MIX 9

MIX10 AUX 2 SLOT4-10 MIX10

MIX11 AUX 3 SLOT4-11 MIX11

MIX12 AUX 4 SLOT4-12 MIX12

MIX13 AUX 5 SLOT4- 1 MIX13

MIX14 AUX 6 SLOT4- 2 MIX14

MIX15 AUX 7 SLOT4- 3 MIX15

MIX16 AUX 8 SLOT4- 4 MIX16

MIX17 AUX 9 SLOT4- 5 MIX17

MIX18 AUX10 SLOT4- 6 MIX18

MIX19 AUX11 SLOT4- 7 MIX19

MIX20 AUX12 SLOT4- 8 MIX20

MIX21 — SLOT4- 9 MIX21

MIX22 — SLOT4-10 MIX22

MIX23 — SLOT4-11 MIX23

MIX24 — SLOT4-12 MIX24

ST AL ST L SLOT4-13 ST AL

ST AR ST R SLOT4-14 ST AR

ST BL — SLOT4- 9 ST BL

ST BR — SLOT4-10 ST BR

CUE L CUE L SLOT4-15 CUE L

CUE R CUE R SLOT4-16 CUE R

*1. The signal assigned to each bus is ﬁxed; it cannot be

changed.

*2. You can enable/disable the assignment for each bus.

However, you cannot send the signal of the same slot

or same input channel to multiple buses. If a signal

already assigned to a bus is selected for a different bus,

the previous assignment will be cancelled.

*3. Assigned from the top in ascending numerical order of

slot number / channel number, according to the settings

of the CASCADE IN PORT SELECT area of the

MIXER SETUP screen (SYS/W.CLOCK function). (this

cannot be changed.)

SYS/W.CLOCK function

228 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

In this screen you can make settings such as phantom

power (+48V), gain, and HPF for each of the internal head

amps (PM5D-RH model and DSP5D only), or for each

channel of an external head amp device that supports

remote control via the dedicated protocol (e.g., Yamaha

AD8HR or AD824).

A DISPLAY MODE

Select one of the following as the type of head amp dis-

played in the screen.

• INTERNAL HA (PM5D-RH/DSP5D)

The internal head amp channels (AD IN 1–48, AD

STIN 1–4) will be displayed.

• EXTERNAL HA 1-4

• EXTERNAL HA 5-8

The channels of an external head amp device (ID num-

ber= 1–4, or ID number= 5–8) connected via the [HA

REMOTE] connector will be displayed.

Hint

Up to eight external devices can be daisy-chained to the

PM5D’s [HA REMOTE] connector. In this case, an ID number

(1–8) is automatically assigned to each device, starting from

the device that is connected directly to the PM5D’s [HA

REMOTE] connector.

B Model name

For each ID number, this indicates the model name of

the external head amp device that is connected. If no

device is connected this will indicate “-----”. However

even in this case, you will be able to make the same set-

tings as when a Yamaha AD8HR is connected.

C Slot/Channel

Here you can view/select the slot and channels to

which the audio output of the external head amp

device is connected.

Note

If an external head amp device is connected to a PM5D slot,

you must specify the appropriate slot/channels manually.

Please note that if you specify an incorrect setting, the input

channel HA indication in screens such as the IN HA screen

may differ from the actual state.

D +48V MASTER

If an AD8HR is connected via the [HA REMOTE] con-

nector, this indicates the master phantom power on/off

status. (Otherwise, this indicates “---”.)

E +48V

Switches phantom power (+48V) on/off for each

channel.

F HPF (High Pass Filter)

Turns the HPF on/off for each channel.

G Cutoff frequency

Specifies the HPF cutoff frequency for each channel of

the AD8HR. Move the cursor to the box, and turn the

[DATA] encoder to adjust the cutoff frequency in a

range of 20–600 Hz.

H GAIN

Adjusts the gain for each channel. Move the cursor to

the knob, and turn the [DATA] encoder to adjust the

gain in a range of –62 dB to +10 dB. The current value

is shown in the box below.

Note

The PAD will be switched on or off internally when the gain of

the PM5D-RH internal head amp is adjusted between –14 dB

and –13 dB. Keep in mind that noise may be generated if

there is a difference between the Hot and Cold output imped-

ance of the external device connected to the INPUT

connector/ST IN connector when using phantom power.

I GANG

If this button is on, the gain settings of two adjacent

odd-numbered/even-numbered channels will change

in tandem, maintaining the current offset value.

J LIBRARY

This button displays the HA LIBRARY screen

(➥ p.230).

Note

When an external head amp device is connected for the first

time, the settings on the external head amp device are used. If

you subsequently recall a HA library item, the HA library set-

tings are used.

HA (Head Amp) screen

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 229

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

In this screen you can specify the amount of attenuation

for each output channel and for each output channel of an

I/O card.

A DISPLAY MODE

Select the channels that will appear in the display, from

the following choices.

• OUTPUT

The screen will show the amount of attenuation for

output channels (MIX channels 1–24, MATRIX chan-

nels 1–8, STEREO A L/R channels, STEREO B L/R

channels), CUE L/R channels, MONITOR L/R/C chan-

nels, and 2TR OUT DIGITAL 1–3 L/R channels.

• SLOT 1-4

The screen will show the amount of attenuation for

each output channel of the I/O cards installed in slots

1–4.

B ø (phase)

If this button is on, the phase of the output port will be

reversed.

C ATT (Attenuation)

Adjusts the amount of attenuation for each channel.

Move the cursor to the box, and turn the [DATA]

encoder to adjust the value in a range of –9 to 0 dB.

In this screen you can turn dithering on/off and specify the

bit depth for dithering. These settings are made individu-

ally for each digital output jack and each output channel of

the digital I/O cards.

A Digital output jack dither

settings

Specify the number of bits (16,

20, 24 bits) used when dither-

ing the output signals from 2TR

DIGITAL OUT jacks 1–3. If you

select OFF, dithering will not be

performed.

B Slots 1–4

This area shows the type of digital I/O card installed in

each slot.

C Digital I/O card dither settings

For each output channel of the digital I/O cards

installed in the slots, specify the number of bits used

when dithering.

OUTPUT PORT ATT (Output port

attenuation) screen

OUTPUT PORT ATT

1 2 3

DITHER screen

DITHER

2 3

SYS/W.CLOCK function

230 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

In this screen you can recall, store, rename, or delete items

in the HA library.

A EDIT

When you click this button, the HA screen will appear.

B DATA FORMAT

Indicates the model name (PM5D or PM5D-RH).

Note

In the case of the DSP5D, it will be indicated as “PM5D-RH.”

C EXTERNAL HA TYPE INFORMATION

This area shows the model names (AD8HR/AD824) of

the external head amp devices (ID numbers= 1–8)

connected to the PM5D’s [HA REMOTE] connector.

D RECALL

Recalls the HA library item selected in the list into

memory.

E STORE

Stores the current settings of the HA screen into the

location selected in the list. When you click this button

a window will appear, allowing you to name and save

the settings.

F TITLE EDIT

Edits the title of the library item selected in the list.

When you click this button a window will appear,

allowing you to edit the title.

G CLEAR

Deletes the library item selected in the list. When you

click this button, a confirmation message will appear.

Note

Library items with an “R” displayed in the right column of the

list are read-only. Read-only items cannot be stored,

renamed, or deleted.

H DATA FORMAT

Indicates the data format (PM5D-RH or PM5D) of the

library item selected in the list.

Note

Data stored by the DSP5D will be indicated as “PM5D-RH.”

I EXTERNAL HA TYPE INFORMATION

This area indicates the model name (AD8HR/AD824)

of the external head amps (ID numbers= 1–8) for

which data is stored in the library.

Note

If a DSP5D (machine #2 or #3) is selected as the target of

control, this information will not be displayed.

J Library list

Use the scroll bar to select the library item on which

you want to perform an operation. The selected library

item will move to the center, and will be highlighted.

Note

• If PM5D format data is recalled to the PM5D-RH, the inter-

nal head amp settings will not change. If PM5D-RH format

data is recalled to the PM5D, the internal head amp settings

will be ignored.

HA LIBRARY screen

HA LIBRARY

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 231

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

• If the recall-source and recall-destination head amp devices

have the same ID number but are assigned to different slots/

channels, the data will not be recalled to head amps of those

ID numbers.

• AD8HR data can be recalled into an AD824, and AD824

data can be recalled into an AD8HR. However when AD8HR

data is recalled to an AD824, the gain settings of each chan-

nel will be converted into 6 dB units in order to match the

specifications of the AD824.

METER function

This screen contains meters that show the input level of the

input channels (input channels 1–48, ST IN channels 1–4,

FXTRN channels 1–4).

A METERING POINT

Select one of the following as the point at which the

input level will be detected. This setting also applies to

the meters on the panel.

PRE ATT . . . . . . . . . Immediately before the

attenuator

PRE GATE . . . . . . . Immediately before the internal

gate

PRE FADER . . . . . . Immediately before the fader

POST FADER . . . . . Immediately after the fader

POST ON . . . . . . . . Immediately after the [ON] key

B CH METER ALWAYS PRE ATT

If this button is on, the input channel meters of the

panel will always show the pre-attenuator levels.

C PEAK HOLD

If this button is on, the peak level of each meter will be

held. When you turn this button off, the peak level

indication that had been held will be cleared. Peak hold

will be cleared when you change the metering point

(

1). This button is linked with the [PEAK HOLD] key

in the METER section of the top panel.

INPUT METER screen

INPUT METER

1 2 3

METER function

232 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

D Meters

These peak level meters indicate the input level of each

channel. The current fader value is shown in the box

below.

If clipping occurs at any point PRE ATT, POST EQ,

POST GATE, POST COMP, INSERT IN, or POST

FADER, the ∑ segment will light.

E Pair icon

This indicates the pairing status of two adjacent odd-

numbered/even-numbered channels.

This screen contains meters that show the output level of

output channels (MIX channels 1–24, MATRIX channels

1–8, STEREO A/B channels), MONITOR (L/R/C), and

CUE (L/R).

A METERING POINT

Select one of the following as the point at which the

output level will be detected.

PRE EQ . . . . . . . . . . Immediately before the EQ

PRE FADER . . . . . . Immediately before the fader

POST FADER . . . . . Immediately after the fader

POST ON . . . . . . . . Immediately after the [ON] key

POST DELAY . . . . . Immediately after the internal

delay (of an output channel)

B CUE METERING POINT

Select one of the following as the point at which the

output level of the cue signal will be detected.

PRE DELAY . . . . . . Immediately before the internal

delay (of a monitor/cue

channel)

POST DELAY . . . . . Immediately after the internal

delay (of a monitor/cue

channel)

C PEAK HOLD

If this button is on, the peak level of each meter will be

held. When you turn this button off, the peak level

indication that had been held will be cleared. Peak hold

will be cleared when you change the metering point

(

1). This button is linked with the [PEAK HOLD] key

in the METER section of the top panel.

OUTPUT METER screen

OUTPUT METER

1 2 3

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 233

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

D Meters

These peak level meters indicate the output level of

each channel. The current master level value is shown

in the box below.

If clipping occurs at any point POST EQ, POST

COMP, POST ON, POST FADER, or INSERT IN, the

∑ segment will light.

E Pair icon

This indicates the pairing status of two adjacent odd-

numbered/even-numbered channels.

This screen contains meters that show the amount of gain

reduction produced by the gate/compressor for each input

channel (input channels 1–48, ST IN channels 1–4).

A GATE/COMP (Gate / Compressor)

These buttons select either Gate or Compressor as the

processor whose gain reduction amount is shown by

the meters. The display at the left will change accord-

ing to your selection.

B Meters

These peak level meters indicate the amount of gain

reduction for each channel. The current fader value is

shown in the box below.

C Pair icon

This indicates the pairing status of two adjacent odd-

numbered/even-numbered channels.

INPUT GR (Input Gain Reduction)

screen

INPUT GR

MON/CUE function

234 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

This screen contains meters that show the amount of gain

reduction produced by the compressor for each output

channel (MIX channels 1–24, MATRIX channels 1–8, STE-

REO A/B channels).

A Meters

These peak level meters indicate the amount of gain

reduction for each channel. The current master level

value is shown in the box below.

B Pair icon

This indicates the pairing status of two adjacent odd-

numbered/even-numbered channels.

MON/CUE function

In this screen you can switch talkback on/off, and select the

talkback destination.

A Level meter (TALKBACK jack level meter)

This level meter indicates the peak level of the signal

being input from the TALKBACK jack of the top panel.

B +48V (TALKBACK jack phantom power)

This button switches phantom power on/off for the

TALKBACK jack.

Note

• The WITH ANALOG VOLUME icon below the button indi-

cates that the LEVEL volume in the TALKBACK section of

the panel will affect only the signal being input from the

TALKBACK jack.

• If the DSP5D is selected, the TALKBACK IN field is not

displayed.

OUTPUT GR (Output Gain Reduction)

screen

OUTPUT GR

TALKBACK screen

TALKBACK

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 235

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

C Talkback input selection

If you want to use an input jack other than the TALK-

BACK jack for purposes of talkback, you can choose it

here from analog inputs AD IN 1–48. The talkback

input selection is not included in the input patch

library.

D HA (PM5D-RH model only)

Here you can switch phantom power on/off and adjust

the gain for the analog input selected in (

3). The

LEVEL volume in the TALKBACK section of the panel

does not affect the talkback input from the analog

input channel. The HA setting is included in the HA

library.

E Level meter (Analog input level meter)

This level meter indicates the peak level of the signal

being input from the analog input selected in (

3).

F ON/OFF (Analog input on/off)

This button switches the talkback input selected in (3)

on/off.

G ON/OFF (Talkback on/off)

This button switches Talkback on/off. This is linked

with the TALKBACK [ON] key in the TALKBACK sec-

tion of the panel.

H NEVER LATCH

This button selects one of the following as the mode in

which the TALKBACK ON/OFF button and the panel

TALKBACK [ON] key will behave.

• If the NEVER LATCH button is off

Talkback will be switched on/off (Latched operation)

each time you click the ON/OFF button or press the

TALKBACK [ON] key. However if you press and hold

down the TALKBACK [ON] key, talkback will stay on

only while you continue holding down the key; talk-

back will turn off when you release the key (Unlatched

operation).

• If the NEVER LATCH button is on

Talkback will be on only while you click and hold

down the ON/OFF button or press and hold down the

TALKBACK [ON] button; talkback will turn off when

you release the button or key (Unlatched operation).

I BUS ASSIGN

Here you can select the bus(es) or output jack(s) from

which the talkback signal will be sent. (Multiple selec-

tions are allowed.)

MIX 1–24 . . . . . . . . MIX bus 1–24

MATRIX 1–8 . . . . . MATRIX bus 1–8

ST A L/R . . . . . . . . . STEREO A bus L/R channels

ST B L/R . . . . . . . . . STEREO B bus L/R channels

J TALKBACK OUT (Talkback direct output)

This indicates the channel of the output jack / slot that

is selected as the output destination for direct output of

the talkback signal. If more than one output destina-

tion is patched, “...” will be displayed following the

name of the output destination that was found first. If

you want to change the output destination, click the

PATCH button to access the OUTPUT PATCH screen.

MON/CUE function

236 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

’Here you can make settings and perform operations

related to the internal oscillator.

A OSC ON/OFF (Oscillator on/off)

Turns the Oscillator on/off. This is linked with the

OSCILLATOR [ON] switch of the top panel.

B OSC MODE (Oscillator mode)

These buttons select the waveform or type of noise pro-

duced by the oscillator.

SINE WAVE 1CH . Sine wave x 1 channel

SINE WAVE 2CH . Sine wave x 2 channels

PINK NOISE . . . . . Pink noise

BURST NOISE . . . . Burst noise (repeated output of

pink noise)

C PARAMETERS

Here you can set various items according to the selec-

tion in (

2).

• If SINE WAVE 1CH is selected

• If SINE WAVE 2CH is selected

• If PINK NOISE is selected

• If BURST NOISE is selected

D LEVEL

This knob adjusts the output level of the oscillator. The

range is –96 dB to 0 dB. The level meter beside the

knob indicates the output level.

E FREQ (Frequency)

This knob specifies the frequency of the sine wave pro-

duced by the oscillator. The range is 20 Hz–20 kHz (the

current setting is shown in the numerical box below).

You can use the 10 kHz /1 kHz / 100 Hz buttons to

select a preset frequency.

Hint

If SINE WAVE 2CH is selected, you can specify the level and

frequency of each channel independently.

F HPF (High Pass Filter)

G LPF (Low Pass Filter)

Here you can make settings for the HPF/LPF through

which the pink noise or burst noise is sent. The knob

above sets the cutoff frequency (20 Hz–20 kHz), and

the button below switches the filter on/off.

OSCILLATOR screen

OSCILLATOR

54 54

6 74

6 74 98

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 237

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

H WIDTH

I INTERVAL

If burst noise is selected, these knobs select the dura-

tion of the noise itself (WIDTH) and the duration of

silence between noise bursts (INTERVAL).

The range is 0.1–10 sec for WIDTH, and 1–30 sec for

INTERVAL. (The current setting is shown in the box

below each knob.)

J OSC OUT (Oscillator direct output)

This indicates the channel of the output jack / slot that

directly outputs the oscillator signal. If you want to

change the output destination, click the PATCH but-

ton to access the OUTPUT PATCH screen.

If SINE WAVE 2CH is selected, the L channel of the

oscillator is sent to the oscillator direct output.

K BUS ASSIGN

Here you can select the bus(es) or output jack(s) from

which the sine wave or noise will be sent. (Multiple

selections are allowed.)

MIX 1–24 . . . . . . . . MIX bus 1–24

MATRIX 1–8. . . . . . MATRIX bus 1–8

AL/AR . . . . . . . . . . . STEREO A bus L/R channels

BL/BR . . . . . . . . . . . STEREO B bus L/R channels

If SINE WAVE 2CH is selected, the L channel of the

oscillator is output to the odd-numbered bus or the L

jack, and the R channel of the oscillator is output to the

even-numbered bus or the R jack.

This screen contains various settings and indications for

2TR IN / 2TR OUT.

Note

The 2TR I/O screen is disabled if the DSP5D is selected.

A Input level meters

These indicate the input level of 2TR IN DIGITAL

jacks 1–3 and 2TR IN ANALOG jacks 1–2.

B FREQUENCY (Sampling frequency)

Indicates the sampling frequency of the input signal

from 2TR IN DIGITAL jacks 1–3.

C SRC (Sampling Rate Converter)

These are on/off switches for the sampling rate con-

verters built into 2TR IN DIGITAL jacks 1–3.

(If turned off, this indicates “THROUGH.”)

D EMPHASIS STATUS

Indicates whether emphasis processing is being applied

to the input signal from 2TR IN DIGITAL jacks 1–3.

INTERVAL

WIDTH

Level

Time

Pink noise output

The BURST NOISE button is on

2TR I/O screen

2TR I/O

MON/CUE function

238 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

E Output level meter

Indicates the output level of 2TR OUT DIGITAL jacks

1–3.

F SRC (Sampling Rate Converter)

These are on/off and output frequency select switches

for the sampling rate converters built into 2TR OUT

DIGITAL jacks 1–3. As the output frequency you can

select either 44.1 kHz or 48 kHz. The on/off button

selects either ON or THROUGH (off).

G Fs (Sampling frequency)

This indicates the sampling frequency at which the

PM5D is operating.

Here you can make settings and perform operations

related to monitoring.

A MONITOR SOURCE

Selects the source that will be monitored from the L/R/

C MONITOR OUT jacks. You can select one from 2TR

IN A1/A2, 2TR IN D1–D3, or DEFINE, and also simul-

taneously select one from STEREO A/B or LCR. These

buttons are linked with the various keys of the MONI-

TOR section in the top panel.

If a monitor source indicated by (*) is selected, the sig-

nal that is output will change depending on whether

2TR IN A1 2TR IN ANALOG jack 1 input signal

2TR IN A2 2TR IN ANALOG jack 2 input signal

2TR IN D1 2TR IN DIGITAL jack 1 input signal

2TR IN D2 2TR IN DIGITAL jack 2 input signal

2TR IN D3 2TR IN DIGITAL jack 3 input signal

STEREO A STEREO A channel output signal (*)

STEREO B STEREO B channel output signal (*)

LCR LCR channel output signal (*)

DEFINE

The signal selected in the DEFINE section

(

2) of this screen

MONITOR screen

MONITOR

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 239

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

the USE AS STEREO BUS button or the USE AS CEN-

TER BUS button is turned on in the STEREO B section

of the MIXER SETUP screen (➥ p.222).

❏ If the USE AS STEREO BUS button is on

❏ If the USE AS CENTER BUS button is on

B DEFINE

If “DEFINE” is selected in the MONITOR SOURCE

section, you can choose the signal that will be moni-

tored from the following.

MIX 1–24 . . . . . . . . MIX bus 1–24 output signal

MATRIX 1–8. . . . . . MATRIX bus 1–8 output signal

C DIMMER

When you turn this button on, the level of the signal

being monitored will be temporarily attenuated. The

knob adjusts the amount of attenuation that will occur

when the button is on. The range of adjustment is

–96 dB to 0 dB. While this button is on, the DIMM

indicator will appear in the upper right of the display.

Hint

You can also use an external switch connected to the GPI IN

connector to switch the dimmer on/off. To do so, assign the

MONITOR DIMMER ON function to the GPI IN port to which

the switch is connected. (

➥

p.194).

D TALKBACK DIMMER

This adjusts the amount by which the monitor signal

will be attenuated when talkback is on. The range of

adjustment is –96 dB to 0 dB. The talkback on/off sta-

tus is shown in the box below.

E CUE INTERRUPTION

If this button is on, the cue/solo signal will also be out-

put from the MONITOR OUT jacks while the Cue/

Solo function is active. During this time, the monitor

source selected in the MONITOR SOURCE section

will be disabled.

If this button is off, the cue/solo signal will never be

output from the MONITOR OUT jacks.

F MONITOR MODE

Here you can select one of the following two ways in

which the signal will be output from the MONITOR

OUT jacks.

STEREO . . . . The L/R channels will be output in

stereo.

MONO . . . . . The L/R channels will be mixed, and

output in monaural.

The status of these two buttons is linked with on/off

operations of the [MONO] key in the MONITOR sec-

tion of the panel.

G MONITOR INSERT

This area shows the input jacks (and input channels of

the digital I/O card) that are inserted into the MONI-

TOR OUT L/C/R channels. The input level of the

inserted signal is shown by the level meter at the right.

If GEQ or EFFECT is inserted, the corresponding

information is shown here.

H INSERT ON/OFF

This button enables/disables insertion.

I PATCH

Displays the INSERT PATCH screen.

Monitor

source

LRC

ST A STEREO A L STEREO A R

—ST B STEREO B L STEREO B R

LCR — —

Monitor

source

LRC

ST A STEREO A L STEREO A R —

ST B — —

STEREO B L

LCR STEREO A L STEREO A R

3 4

MON/CUE function

240 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

J Level meter

These peak level meters indicate the level of the output

signal from the MONITOR OUT jacks. You can select

the level detection point to be immediately before the

delay that is provided on the MONITOR/CUE bus

output (when the PRE DELAY button is on) or imme-

diately after the delay (when the POST DELAY button

is on).

K MONITOR / CUE DELAY

Here you can make settings for the delay function pro-

vided on the MONITOR/CUE bus output. Use the

knob to specify the delay time (0–1000 msec), and use

the ON/OFF button to switch the delay on/off. If the

ON/OFF button is on, the monitor signal and cue sig-

nal will be delayed by the specified time. The delay time

units can be changed in the DELAY SCALE field found

in each screen of the INPUT DELAY/OUTPUT

DELAY function.

L MONITOR LEVEL

The level of the signal sent from the MONITOR OUT

jacks is set by the level (digital) you adjust here together

with the level (analog) adjusted by the MONITOR

[LEVEL] knob on the top panel of the PM5D.

M MONITOR OUT

Switches the signal sent from the MONITOR OUT

jacks on/off.

Here you can make settings and perform operations

related to the Cue/Solo function.

A SOLO ON/OFF

This button selects either

CUE mode or SOLO mode

as the type of monitoring

performed by the [CUE] key.

When you turn this button

on, a confirmation message

will appear. Each mode

operates as follows.

• CUE mode (SOLO ON/OFF

button is off)

The signal of the channel

whose [CUE] key is pressed

will be sent to the dedicated

CUE bus, and monitored via

the CUE bus from the CUE

OUT jacks, MONITOR

OUT jacks (if CUE INTERRUPTION is on), and

PHONE jack. This mode lets you monitor the signal of

a specific channel without affecting other buses.

• SOLO mode (SOLO ON/OFF button is on)

When using Input Solo, the familiar “solo” function is

enabled; only the signal of the channel whose [CUE]

key is pressed will be sent to the MIX, MATRIX, and

STEREO A/B buses, and other channels will be muted.

When using Output Solo, only that channel will be on.

The signal of a channel whose [CUE] key is pressed can

also be monitored from the CUE OUT jacks, MONI-

TOR OUT jacks, and PHONES jack.

B CUE MODE

This button selects one of the following two possibili-

ties for when the [CUE] key of more than one channel

is pressed.

• MIX CUE mode

All channels / DCA groups whose [CUE] key is on will

be mixed for monitoring.

CUE/SOLO screen

CUE/SOLO

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 241

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

Note

As an exception to MIX CUE, turning on a CUE button in the

EFFECT PARAM screen or GATE PARAM screen or turning

on a CUE button in the DME CONTROL screen (EXTERNAL

CUE) will give priority to monitoring only the corresponding

signal. (Any [CUE] keys that had been on until then will be

forcibly defeated.)

• LAST CUE mode

Only the channel / DCA group whose [CUE] key was

pressed last will be monitored.

C CUE FUNCTION

These buttons let you turn on/off various functions

related to Cue. You can select the following functions.

• MIX CUE LINK

Specifies whether cue operations will be linked to MIX

channel selection. If this button is on, pressing the mix

key selected in the ENCODER MODE section of the

panel once again will simultaneously switch on the

[CUE] key of that channel.

• CUE/SEL LINK

Specifies whether channel selection will be linked with

cue operations. If this button is on, pressing the [CUE]

key of a channel will simultaneously select that chan-

nel and light its [SEL] key.

• FADER/CUE RELEASE

This specifies whether cue operations will be restricted

according to the fader position. If this button is on, cue

will be defeated if you raise the fader from the –∞ dB

position for a channel whose [CUE] key is lit. For a

channel whose fader is above the

–∞ dB position, cue operation will not be possible.

(Pressing the [CUE] key will do nothing.) This means

that cue can be turned on only when the fader is at the

–∞ dB position.

D INPUT

Here you can select the position from which an input

channel will be cued.

PFL (Pre-Fader Listen)

. . . . . . . Immediately before the fader

AFL (After-Fader Listen)

. . . . . . . Immediately after the fader

POST PAN . . . . . . . Immediately after pan

If you select PFL, you can also use the knob located at

the left to adjust the output level in a range of

–20 dB to +10 dB.

E DCA

Here you can make cue output settings for DCA

groups.

• DCA TRIM

Adjusts the level of cue output from a DCA group in a

range of –20 dB to +10 dB.

• DCA UNITY

If this button is on, pressing a DCA [CUE] key will

always monitor the corresponding DCA group at unity

gain (the same level at when the DCA fader is at 0 dB).

Hint

• If you leave the DCA UNITY button on, you will be able to

monitor the desired DCA group even if that DCA group is

muted or its fader is lowered.

• Even when the DCA UNITY button is on, the value specified

by the DCA TRIM knob is still valid. (In this case, the DCA

TRIM knob specifies an offset value relative to unity gain.)

• PRE PAN/POST PAN

This selects whether the pre-pan signal (PRE PAN but-

ton on) or the post-pan signal (POST PAN button is

on) will be monitored when the DCA [CUE] button is

turned on.

F OUTPUT

Here you can select the position from which an output

channel will be cued.

PFL (Pre-Fader Listen)

. . . . . . . . Immediately before the fader

POST ON . . . Immediately after the [ON] key

If you select PFL, you can also use the knob located at

the left to adjust the output level in a range of

–20 dB to +10 dB.

G INPUT SOLO SAFE

Here you can specify input channels that will be

excluded from Solo operations. (You can specify more

than one.) The buttons correspond to the following

input channels.

4 5 6

INPUT 1–48 Input channels 1–48

ST IN 1–4 ST IN channels 1–4

FX RTN 1–4 FX RTN channels 1–4

SET ALL

Sets all input channels to the Solo

Safe condition

CLEAR ALL

Defeats the Solo Safe setting for

all input channels

MON/CUE function

242 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

H OUTPUT SOLO SAFE

Here you can specify output channels that will be

excluded from Solo operations. (You can specify more

than one.) The buttons correspond to the following

output channels.

Hint

Solo Safe settings and Cue on/off operations are linked for

paired channels. Solo Safe operations can be performed inde-

pendently of the scene memory.

I Level meter

This is a peak level meter that indicates the level of the

signals output from the CUE OUT jacks. You can select

the level detection point to be immediately befor the

delay that is provided on the MONITOR/CUE bus

output (when the PRE DELAY button is on), or imme-

diately after the delay (when the POST DELAY button

is on).

J MONITOR / CUE DELAY

Here you can make settings for the delay function pro-

vided on the MONITOR/CUE bus output. Use the

knob to specify the delay time (0–1000 msec), and use

the DELAY button to switch the delay on/off. In gen-

eral, this is linked with the MONITOR/CUE DELAY

setting in the MONITOR screen. However, the differ-

ence is that in this screen, turning the AUTO BYPASS

button on lets you automatically bypass the delay when

you perform the Cue any input channels.

K CUE LEVEL

The level of the signal sent from the CUE OUT jacks is

set by the level (digital) you adjust here together with

the level (analog) adjusted by the CUE [LEVEL] knob

on the top panel of the PM5D.

L CUE OUT

Switches the cue output on/off.

MIX 1–24 MIX channels 1–24

MATRIX 1–8 MATRIX channels 1–8

STEREO A/B STEREO A/B channels

SET ALL

Sets all output channels to the

Solo Safe condition

CLEAR ALL

Defeats the Solo Safe setting for

all output channels

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 243

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

OUTPUT PATCH function

Here you can make patch settings to send output channel

signals to the outputs of I/O cards installed in the MIX

OUT jacks and slots, to the input of internal effects, and to

the 2TR OUT DIGITAL jacks.

A SELECTED PATCH

This indicates the output channel number, name and

output port of the grid at which the cursor is located.

B CH (Output channel)

This is the number and name of the output channel

(MIX channel, MATRIX channel, STEREO A/B chan-

nel, MONITOR L/R/C channel, CUE L/R channel,

TALKBACK OUT channel, OSC OUT channel) whose

output destination will be patched. The channel num-

ber at which the cursor is located will be highlighted.

When you click the name area, a window will appear,

allowing you to assign a name to the channel.

Note

On the PM5D, this is unavailable for the CUE L/R channels;

on the DSP5D, this is unavailable for the MONITOR L/R/C

channels.

C ASSIGN

For each output channel, this indicates the number of

output ports that are currently assigned.

D Grid

This grid lets you patch output ports (horizontal rows)

to output channels (vertical columns). Currently-

patched grids are indicated by a symbol. By clicking

a grid location you can set/cancel patching.

The red lines at the left and top indicate the grid loca-

tion to which you move the cursor.

Hint

• If PATCH CONFIRMATION is turned on in the PREFER-

ENCE 1 screen (UTILITY function), a confirmation message

will appear each time you attempt to change a patch set-

ting. If STEAL PATCH CONFIRMATION is turned on, a

confirmation message will also appear when you attempt to

make patch settings that would cause an existing patch to

be modified.

• To move the cursor location rapidly in or out of the grid, hold

down the [SHIFT] key and press the CURSOR [

√

]/[

[

†

] keys.

• To move rapidly to left or right inside the grid, turn the

[DATA] encoder. To move up or down, hold down the

[SHIFT] key and turn the [DATA] encoder.

Note

You can patch an output channel to more than one output

port, but you cannot patch multiple output channels to a sin-

gle output port.

E Output port

From the top, this area indicates the type of output

port, the ID number, the output channel number, and

the number of output channels assigned. The follow-

ing types of output port can be selected.

Note

On the DSP5D, you can choose from OMNI OUT 1-24, SLOT

OUT 1-4 (SLOT OUT 3-4 is the CASCADE OUT connector),

and FX IN 1-8.

Output functions

OUTPUT PATCH screen

OUTPUT PATCH

MIX OUT MIX OUT jacks 1–24

SLOT OUT

Output channels of an I/O card installed in slots

1–4

FX IN

L/R inputs of internal effects 1–8 (MIX chan-

nels are the only output channels that can be

selected)

2TR OUT L/R channels of 2TR OUT DIGITAL jacks 1–3

OUTPUT PATCH function

244 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

F LIBRARY button

This button accesses the OUTPUT PATCH LIBRARY

screen (➥ p.247), where you can store/recall patch

library settings for output channels.

Hint

• The signal from immediately after the delay and immedi-

ately before the output port attenuation will be sent to output

ports you patch in this screen. Subsequently, in the case of

SLOT OUT and 2TR OUT, the specified output port attenua-

tion will be applied respectively.

• The rear panel MATRIX OUT jacks 1–8, and STEREO OUT

jacks A/B always output the signal of the corresponding out-

put channel. They are not affected by the settings in this

screen.

In this screen you can patch the input/output ports into

which external devices will be inserted. Select the output

port in the left side of the screen, and the input port in the

right side of the screen.

A SELECTED PATCH

This indicates the number and name of the output

channel at which the cursor is located in the grid.

B Insert in/out

This indicates the input/output ports that are patched

as insert in/out for the output channel at which the

cursor is located. If multiple ports are assigned for

insert-out, only the first port is displayed.

C CH (Output channel)

This area shows the numbers and names of the output

channels (MIX channels, MATRIX channels, STEREO

A/B channels, MONITOR L/R/C channels). The chan-

nel number at which the cursor is located will be

highlighted. When you click the name area, a window

will appear, allowing you to assign a name to the

channel.

Note

On the DSP5D, this is unavailable for the MONITOR L/R/C

channels.

INSERT PATCH screen

INSERT PATCH

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 245

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

D ASSIGN

For each output channel, this indicates the number of

output ports that are currently assigned as insert-out.

E Grid

For each output channel (vertical column), this grid

lets you can patch one or more output ports (horizon-

tal row) to be used as insert-outs. Currently-patched

grids are indicated by a symbol.

By clicking a grid location you can set/cancel patching.

The red lines at the left and top indicate the grid loca-

tion to which you move the cursor.

Hint

Operations in the grid are the same for all of the patching

screens. For details, refer to the Hint on p.243.

F Output port

From the top, this area indicates the type of output

port, the ID number, the output channel number, and

the number of output channels assigned. The follow-

ing types of output port can be patched as insert-out.

Note

On the DSP5D, you can choose from OMNI OUT 1-24, SLOT

OUT 1-4 (SLOT OUT 3-4 is the CASCADE OUT connector),

FX IN 1-8, and GEQ IN 1-20.

Hint

If you select FX IN as an insert-out, the output of the same

internal effect will automatically be selected as the insert-in. If

you select GEQ IN, the output of the same GEQ module will

automatically be selected as the insert-in.

G ASSIGN

For each input channel, this indicates the number of

input ports that are currently assigned as insert-in.

H Input port

From the top, this area indicates the type of input port,

the ID number, the input channel number, and the

number of input channels assigned. The following

types of input port can be selected.

Note

On the DSP5D, you can choose from OMNI OUT 1-24, SLOT

OUT 1-4 (SLOT OUT 3-4 is the CASCADE OUT connector),

FX IN 1-8, and GEQ IN 1-20.

I LIBRARY button

This button accesses the OUTPUT PATCH LIBRARY

screen (➥ p.247), where you can store/recall patch

library settings for output channels.

❏ Using the [SHIFT] key + CURSOR [√]/

[®] to move the cursor

When operating from the panel, you can move the cur-

sor from the right side of the screen to the left side (or

vice versa) by holding down the [SHIFT] key and using

the CURSOR [√]/[®] keys.

To quickly move the cursor in or out of the grid, hold

down the [SHIFT] key and press the CURSOR [√]/

[®]/[π]/[†] keys.

Note

To enable an insert-in assigned to an output channel in this

screen, you must turn on the ON/OFF button for the corre-

sponding output channel in the INSERT POINT screen

(OUTPUT PATCH function). (

➥

p.246) However, the insert-

out is always on, regardless of the state of the ON/OFF but-

ton. An exception to the above is that if you insert GEQ, its

insert-in will automatically be on.

MIX OUT MIX OUT jacks 1–24

SLOT OUT

Output channels of an I/O card installed in slots

1–4

FX IN L/R inputs of internal effects 1–8

GEQ IN Inputs of internal GEQ modules 1–20

2TR OUT L/R channels of 2TR OUT DIGITAL jacks 1–3

AD IN INPUT jacks 1–48

AD ST IN ST IN jacks 1–4 L/R

SLOT IN

Input channels of an I/O card installed in slots

1–4

FX OUT L/R outputs of internal effects 1–8

GEQ OUT Outputs of GEQ modules 1–20

2TR IN

L/R channels of 2TR IN DIGITAL jacks 1–3 and

2TR IN ANALOG jacks 1/2

➠

[SHIFT] key

CURSOR [®] key

Cursor

Cursor will move

OUTPUT PATCH function

246 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

In this screen you can select the position at which the

insert-in/out of each output channel will be patched. Here

you can also switch insert-in on/off.

A Insert view

When you move the cursor to the insert I/O point

(

4), the insert point for that output channel will be

shown graphically.

B OUTPUT CH (Output channel)

This is the number and name of the output channel

you are editing. Two paired channels are indicated by a

heart symbol shown at the left; settings

3–4 will be

linked for these channels. You can click this symbol to

enable/disable pairing.

C ON/OFF (Insert on/off)

This button switches insert on/off for each channel.

This is linked for paired channels.

Note

Be aware that if you turn on this button when either insert-in or

insert-out are unpatched, the signal will no longer be output

from the corresponding output channel.

D INSERT I/O (Insert I/O point)

Here you can select one of the following as the insert-

in/out location for each output channel.

E SET ALL

Turns on the corresponding item (insert or the insert

point) for all channels (including channels not cur-

rently shown in the screen).

F CLEAR ALL

Turns insert off for all channels (including channels

not currently shown in the screen).

INSERT POINT screen

INSERT POINT

PRE EQ Immediately before the EQ

POST EQ Immediately after the EQ

PRE FADER Immediately before the fader

POST ON Immediately after the [ON] key

3 4

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 247

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

Here you can assign names to the output channels. How-

ever, display in the CH COPY, GLOBAL PASTE, and CSV

IMPORT/EXPORT functions is not supported.

A Channel

This is the number of the output channel (MIX chan-

nel, MATRIX channel, or STEREO A/B channel).

B Name

This is the name currently assigned to the output chan-

nel. When you click the name area, a window will

appear, allowing you to assign a name to the channel.

C LIBRARY

This button displays the OUTPUT PATCH LIBRARY

screen (➥ p.247) where you can store or recall the state

of the output channel patching (and names) as library

data.

Here you can recall, store, rename, or delete items in the

output patch library.

A EDIT

When you click this button, the OUTPUT PATCH

screen will appear.

B Patch information for the current scene

This area shows the output patch settings for the cur-

rent scene.

Note

If a DSP5D (machine #2 or #3) is selected as the target of

control, this information will not be displayed.

NAME screen

NAME

1 2 3

OUTPUT PATCH LIBRARY screen

OUTPUT PATCH LIBRARY

OUTPUT INSERT function

248 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

C RECALL

Recalls the output patch library item selected in the list

into memory.

D STORE

Stores the current settings of the OUTPUT PATCH

screen into the location selected in the list. When you

click this button a window will appear, allowing you to

name and save the settings.

E TITLE EDIT

Edits the title of the library item selected in the list.

When you click this button a window will appear,

allowing you to edit the title.

F CLEAR

Deletes the library item selected in the list. When you

click this button, a confirmation message will appear.

Note

Library items with an “R” displayed in the right column of the

list are read-only. Read-only items cannot be stored,

renamed, or deleted.

G Patch settings of the library item

Displays the settings of the library item selected in the

list.

H Library list

Use the scroll bar to select the library item on which

you want to perform an operation. The selected library

item will move to the center, and will be highlighted.

OUTPUT INSERT function

Here you can make settings for the internal HA (PM5D-

RH model only) or external HA assigned to the insert-in of

an output channel or MONITOR L/C/R channel.

INSERT IN MIX 1-24 screen

INSERT IN MATRIX/STEREO/MONI-

TOR screen

INSERT IN MIX1-24

INSERT IN MATRIX/STEREO/MONITOR

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 249

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

A +48V

Switches phantom power (+48V) on/off for each

channel.

B HPF (High Pass Filter)

Turns the HPF on/off for each channel.

C Cutoff frequency

Specifies the HPF cutoff frequency for each channel.

Move the cursor to the box, and turn the [DATA]

encoder to adjust the cutoff frequency in a range of 20–

600 Hz.

D GAIN

Adjusts the gain for each channel. Move the cursor to

the knob, and turn the [DATA] encoder to adjust the

attenuation in a range of +10 dB to –62 dB. The cur-

rent value is shown in the box below each knob.

Note

Since settings

–

are for the patched input port, they are

linked for channels that are patched to the same port.

E Input port

This indicates the type and number of the input port

assigned to the insert-in of that channel.

Note

• Items

–

are not shown for channels to whose insert-in

nothing is patched, or for channels patched to an input port

that does not have a HA. Items

and

are not shown for

channels patched to a port that has no high pass filter.

• Use the INSERT PATCH screen (OUTPUT PATCH func-

tion) to patch an input port to an insert-in.

F Channel

This is the number and name of the channel you are

editing. Two paired channels are indicated by a heart

symbol displayed between them.

Note

HA settings are not linked even if two channels are paired.

However, the GAIN knob setting is linked for HAs whose

GANG button is turned on in the HA screen (SYS/W.CLOCK

function).

Hint

The HA settings you edit in this screen are also reflected in

the HA screen (SYS/W.CLOCK function).

This screen is shared with HA LIBRARY in the SYS/

W.CLOCK function (➥ p.230).

HA LIBRARY screen

HA LIBRARY

OUTPUT EQ function

250 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

OUTPUT EQ function

Here you can edit the EQ parameters of the selected out-

put channel.

(If a MIX channel or STEREO A/B channel is selected)

(If a MATRIX channel is selected)

A Channel selection

Select the output channel that you want to edit. You

can use eight-band EQ (four UPPER bands + four

LOWER bands) for MIX channels and STEREO A/B

channels, and four-band EQ for MATRIX channels.

If a channel is paired (or if a STEREO A/B channel is

selected), a heart symbol is displayed at the right. For

MIX channels or MATRIX channels, you can click this

symbol to enable/disable pairing.

B EQ ON/OFF (EQ on/off)

Turns the EQ on/off for that channel.

C EQ LINK GROUP

Selects the EQ link group (A–H) to which the EQ of

that channel belongs. EQ parameters are linked for

output channels belonging to the same group.

Note

The EQ of MIX channels and STEREO A/B channels can be

assigned only to groups A–F, and the EQ of MATRIX chan-

nels can be assigned only to groups G/H.

D LIBRARY

This button accesses the OUTPUT EQ LIBRARY

screen (➥ p.252), where you can store/recall EQ

library settings for output channels.

E EQ TYPE

Selects the type of EQ. Turning the TYPE I button on

selects the algorithm used in the 02R series. Turning

the TYPE II button on selects a newly developed algo-

rithm. TYPE II reduces the interference between bands.

F EQ graph

This graph shows the approximate response of the EQ

parameters. The colored vertical lines indicate the

FREQ (center frequency) of the band for the parame-

ter at which the cursor is located. (The color of each

line matches the knob markings for each band.) The

response curve will change when you edit the Q or

GAIN of each band.

G Level meter

These meters indicate the peak levels before EQ and

after EQ. If the signal clips before EQ, the OVER seg-

ment will light.

H EQ FLAT

This button resets the GAIN parameters of all bands to

the default value (±0.0 dB). When you click this but-

ton, a confirmation message will appear.

I LOWER/UPPER (only for MIX channels and

STEREO A/B channels)

This indicator shows which four bands (LOWER or

UPPER) are selected in the SELECTED CHANNEL

section of the panel. The text label of the selected group

is displayed in yellow.

EQ PARAM (EQ Parameter) screen

EQ PARAM

1 2 4

8 7

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 251

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

J Knobs

These knobs adjust the Q, FREQ (center frequency),

and GAIN (amount of boost/cut) for each band.

K BYPASS

These buttons bypass each band of the EQ.

L (LOW shelving)

If this button is on, the LOW EQ will function as a

shelving-type EQ. The Q knob will disappear.

M HPF (High Pass Filter)

If this button is on, the LOW EQ will function as a

high-pass filter. The Q knob will disappear, and the

GAIN knob is used to switch the HPF on/off.

N (HIGH shelving)

If this button is on, the HIGH EQ will function as a

shelving-type EQ. The Q knob will disappear.

O LPF (Low Pass Filter)

If this button is on, the HIGH EQ will function as a

low-pass filter. The Q knob will disappear, and the

GAIN knob is used to switch the LPF on/off.

These screens list the EQ settings for all output channels.

Here you can also copy EQ settings between output

channels.

L M N O

MIX 1-24 screen

MATRIX/STEREO screen

MIX 1-24

MATRIX/STEREO

OUTPUT EQ function

252 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

A EQ graph

This mini-graph shows the approximate EQ response

for each output channel.

When you click the graph at which the cursor is cur-

rently located, the EQ PARAM screen for that channel

will appear.

In this screen you can drag and drop the mini-graph

from the desired channel to copy its EQ settings.

(When you drag and drop the mini-graph, a message

will ask you to confirm the copy operation.)

You can also copy EQ settings between the MIX 1-24

screen and the MATRIX/STEREO screen. First drag the

mini-graph over the MIX 1-24 tab or MATRIX/STE-

REO tab in the screen (the screen will switch). Then

drag and drop the mini-graph onto the desired chan-

nel, and a message will ask you to confirm the copy

operation.

You can also copy settings between the eight-band EQ

of a MIX channel or STEREO A/B channel and the

four-band EQ of a MATRIX channel. In this case, only

the LOWER four bands will be copied for MIX chan-

nels or STEREO A/B channels.

B EQ ON/OFF (EQ on/off)

Turns the EQ on/off for that channel. This is linked for

paired channels.

C Channel

This is the number and name of the channel you are

editing. Two paired channels are indicated by a heart

symbol displayed between them.

D Level meter

This meter indicates the peak level after EQ. If the sig-

nal clips, the OVER segment will light.

Here you can recall, store, rename, or delete items in the

output EQ library.

A EDIT

When you click this button, the EQ PARAM screen for

the currently selected output channel will appear.

B Channel selection

Select the channel that you want to edit.

C EQ graph for the selected channel

This graph shows the approximate response of the EQ

for the currently selected channel.

D Level meter

These meters indicate the peak levels before EQ and

after EQ. If the signal clips before EQ, the OVER seg-

ment will light.

4 1 2

OUTPUT EQ LIBRARY screen

OUTPUT EQ LIBRARY

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 253

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

E RECALL

Recalls the EQ library item selected in the list into

memory.

F STORE

Stores the EQ settings of the currently selected channel

into the location selected in the list. When you click

this button a window will appear, allowing you to

name and save the settings.

G TITLE EDIT

Edits the title of the library item selected in the list.

When you click this button a window will appear,

allowing you to edit the title.

H CLEAR

Deletes the library item selected in the list. When you

click this button, a confirmation message will appear.

Note

Library items with an “R” displayed in the right column of the

list are read-only. Read-only items cannot be stored,

renamed, or deleted.

I Library EQ graph

This graph indicates the approximate response of the

EQ library item selected in the list. The LIBRARY

TYPE indication shows whether the item contains

eight-band EQ settings (MIX, STEREO A/B or GEQ)

or four-band EQ settings (MATRIX).

J Library list

Use the scroll bar to select the library item on which

you want to perform an operation. The selected library

item will move to the center, and will be highlighted.

OUTPUT COMP function

Here you can edit the compressor parameters of the

selected output channel.

A Channel selection

Select the channel that you want to edit. If the corre-

sponding MIX channel or MATRIX channel is paired

(or if a STEREO A/B channel is selected), a heart sym-

bol is displayed at the right. For MIX channels or

MATRIX channels, you can click this symbol to

enable/disable pairing.

B COMP ON/OFF (Compressor on/off)

Turns the compressor on/off for that channel.

C COMP LINK GROUP (Compressor link

group)

Selects the compressor link group (A–H) to which that

channel belongs. Compressor parameters are linked for

output channels belonging to the same group.

D LIBRARY

This button accesses the COMP LIBRARY screen

(➥ p.256), where you can store/recall compressor

library settings for output channels.

COMP PARAM (Compressor parame-

ter) screen

COMP PARAM

1 2 43

OUTPUT COMP function

254 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

E Level meters

These meters indicate the amount of gain reduction

(GR), the peak level before (PRE) and after (POST) the

compressor, and the peak level of the key-in signal

(KEY IN) that causes the compressor to operate. If the

signal clips, the OVER segment will light.

If stereo link is turned on for the corresponding MIX

channel or MATRIX channel (or if a STEREO A/B

channel is selected), level meters for two channels are

displayed.

Hint

If GR METER ON/OFF LINK is turned on in the PREFER-

ENCE 1 screen (UTILITY function), the gain reduction meter

will not be displayed when the compressor is off.

F Type

Indicates the type of the currently selected compressor.

Hint

To change the compressor type, use the OUTPUT COMP

LIBRARY screen to recall a library item that has a different

type. You cannot change the compressor type in this screen.

G STEREO LINK

This specifies whether parameter settings and compres-

sor operation by a key-in signal will be linked

(STEREO LINK button on) for adjacent odd-num-

bered/even-numbered MIX/MATRIX channels or the

L/R channels of the STEREO A/B channels, or not

(STEREO LINK button off).

❏ Key-in signal flow when Link= On

❏ Key-in signal flow when Link= Off

Note

Stereo Link is fixed at On for paired channels and for STE-

REO A/B channels.

H Compressor graph

This graph displays the approximate response of the

compressor.

I KEY IN SOURCE

Select the desired key-in signal from the following

choices.

6 97 8

SELF PRE EQ

The pre-EQ signal of the currently

selected output channel

SELF POST EQ

The post-EQ signal of the currently

selected output channel

MIX1–24 POST EQ The post-EQ signal of the corre-

sponding output channel (however,

you can only select from the group

to which that channel belongs,

from the three groups MIX 1–12,

MIX 13–24, and MATRIX/ST)

MATRIX1–8 POST EQ

ST AL/AR POST EQ

ST BL/BR POST EQ

MIX21–24

The output signal of the corre-

sponding MIX channel immedi-

ately before the output patch

THR

LINK= ON

Key-in signal of odd-

numbered channel

Key-in signal of even-

numbered channel

AT TACK

processing

AT TACK

processing

Detect the

maximum

level

THR

LINK= OFF

Key-in signal of odd-

numbered channel

Key-in signal of even-

numbered channel

AT TACK

processing

AT TACK

processing

Detect the

maximum level

Detect the

maximum level

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 255

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

J THRESHOLD (Threshold level)

Specifies the threshold level at which the compressor

will operate. The input signal will start being com-

pressed when the key-in signal exceeds this level;

compression will be removed when the signal falls

below this level.

K RATIO

Specifies the ratio at which the input signal will be

compressed when the key-in signal exceeds the thresh-

old level.

L ATTACK (Attack time)

Specifies the time from when the key-in signal exceeds

the threshold level until compression begins.

M RELEASE (Release time)

Specifies the time from when the key-in signal falls

below the threshold level until compression is

removed.

N GAIN

Specifies the output level gain.

O KNEE

Select the sharpness at which the output level changes;

the range is HARD or 1–5. HARD produces the sharp-

est change, and 5 produces the most gradual change.

These screens show the compressor settings for all output

channels. Here you can also copy compressor settings

between output channels.

A Compressor graph

This mini-graph shows the approximate compressor

response for each output channel.

When you click the graph at which the cursor is cur-

rently located, the COMP PARAM screen for that

channel will appear.

In this screen you can drag and drop the mini-graph

from the desired channel to copy its compressor set-

tings. (When you drag and drop the mini-graph, a

J K L M N O

MIX 1-24 screen

MATRIX/STEREO screen

MIX 1-24

MATRIX/STEREO

2 1 3

OUTPUT COMP function

256 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

popup window will ask you to confirm the copy

operation.)

You can also copy compressor settings between the

MIX 1-24 screen and the MATRIX/STEREO screen.

First drag the mini-graph over the MIX 1-24 tab or

MATRIX/STEREO tab in the screen (the screen will

switch). Then drag and drop the mini-graph onto the

desired channel, and a message will ask you to confirm

the copy operation.

B Level meters

These meters show the amount of gain reduction pro-

duced by the compressor (at left), and the peak level of

the signal after passing through the compressor (at

right). If the signal clips, the OVER segment will light.

C COMP ON/OFF (Compressor on/off)

Turns the compressor on/off for that channel.

D Channel

This is the number and name of the channel you are

editing. Two paired channels are indicated by a heart

symbol displayed between them.

Here you can recall, store, rename, or delete items in the

compressor library. The contents of this screen are in com-

mon with the COMP LIBRARY screen of the INPUT

GATE/COMP function.

A EDIT

When you click this button, the COMP PARAM screen

for the currently selected channel will appear.

B Channel selection

Select the channel that you want to edit.

C Compressor graph of the selected channel

This graph shows the approximate response of the

compressor for the currently selected channel.

D Level meters

These meters show the amount of gain reduction (GR),

and the peak levels before the compressor (PRE) and

after the compressor (POST). If the signal clips, the

OVER segment will light.

COMP LIBRARY (Compressor library)

screen

COMP LIBRARY

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 257

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

E RECALL

Recalls the compressor library item selected in the list

into memory.

F STORE

Stores the compressor settings of the currently selected

channel into the location selected in the list. When you

click this button a window will appear, allowing you to

name and save the settings.

G TITLE EDIT

Edits the title of the library item selected in the list.

When you click this button a window will appear,

allowing you to edit the title.

H CLEAR

Deletes the library item selected in the list. When you

click this button, a confirmation message will appear.

Note

Library items with an “R” displayed in the right column of the

list are read-only. Read-only items cannot be stored,

renamed, or deleted.

I Compressor graph of the library item

This graph indicates the approximate response of the

compressor library item selected in the list.

J Library list

Use the scroll bar to select the library item on which

you want to perform an operation. The selected library

item will move to the center, and will be highlighted.

OUTPUT DELAY function

Here you can edit the delay parameters of the selected out-

put channel.

A DELAY SCALE

The unit you select here is used to indicate the delay

time in the box below the delay time knob (

3) and in

other screens. You can choose one of the following

units.

• METER

The distance in meters, calculated as the speed of

sound at an air temperature of 20°C (343.59 m/s) x the

delay time (seconds).

• FEET

The distance in feet, calculated as the speed of sound at

an air temperature of 20°C (68°F) (1127.26 feet/s) x

the delay time (seconds).

MIX 1-24 screen

MATRIX/STEREO screen

MIX1-24

MATRIX/STEREO

OUTPUT DCA/GROUP function

258 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

• SAMPLE

The delay time is shown as a number of samples. If you

change the sampling frequency at which the PM5D

operates, the number of samples will change

accordingly.

• msec (milliseconds)

The delay time is shown in units of milliseconds. If this

button is on, the boxes above and below the delay time

knob (

3) will show the same values.

• BEAT

The delay time is shown in units relative to the note

length (considered as 1.0) specified by the tempo

(BPM) and note value (NOTE).

To specify the tempo, you can either use the /

buttons located immediately below the BEAT button,

or repeatedly tap (click) the TAP button, or repeatedly

click a User Defined key that is assigned to [TAP

TEMPO]-[CURRENT PAGE].

• FRAME

The delay time is shown in units of frames.

Use the six buttons located below the FRAME button

to select the number of frames per second.

Hint

• If you change the DELAY SCALE setting of the OUTPUT

DELAY function screen, the DELAY SCALE setting of the

INPUT DELAY function screen will change in tandem.

• The TAP button of the OUTPUT DELAY function is indepen-

dent from the TAP TEMPO button of the internal effect.

• The number of frames per second is linked with the TIME

CODE SETUP field in the EVENT LIST screen (SCENE

function).

B GANG

This button specifies whether the delay parameters will

be linked for adjacent odd-numbered/even-numbered

channels. This can be specified independently of pair-

ing. If the GANG button is turned on for channels of

differing delay times, turning the delay time knob (

will change the delay times of both channels while

maintaining the difference in their delay time.

C Delay time knob

This knob sets the delay time of each channel. The box

below the knob shows the delay time in the units you

selected in (

1). The box above the knob always shows

the delay time in millisecond units.

D DELAY ON/OFF

This button switches delay on/off. This is linked for

paired channels.

E Channel

This is the number and name of the channel you are

editing. Two paired channels are indicated by a heart

symbol displayed between them. You can click this

symbol to enable/disable pairing.

OUTPUT DCA/GROUP func-

tion

Here you can specify the output channels that will be

assigned to DCA groups 7/8. You can use DCA faders 7/8

to uniformly adjust the levels of output channels belong-

ing to the same DCA group.

A DCA group

This is the number of the DCA group. The number

corresponding to the grid where the cursor is located is

highlighted.

B Name

This is the name of the DCA group. You can also click

this area to edit the name.

C Grid

This grid lets you assign output channels (horizontal

rows) to DCA groups (vertical columns). Currently-

patched grids are indicated by a symbol. Move the

cursor to the desired grid and press the [ENTER] key

(or click) to set/disable the assignment.

Hint

• You can also assign an output channel to both DCA groups

for multiple DCA control.

• DCA groups 1–6 are for input channels only, but DCA

groups 7/8 can be used with both input channels and output

channels. DCA groups 7/8 allow you to use both types of

channel in the identically-numbered group.

DCA GROUP ASSIGN screen

DCA GROUP ASSIGN

213

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 259

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

D SET BY CUE (Assign by [CUE] key)

This specifies whether the [CUE] key will be used to

make/cancel DCA group assignments. While the DCA

group SET BY CUE button is on, pressing the [CUE]

key of a channel that can be assigned to the corre-

sponding group will assign the channel to the group.

(Press the [CUE] key once again to cancel the

assignment.)

Hint

• The SET BY CUE button can be turned on for only one DCA

group. This is automatically turned off when you change

screens or turn off the power.

• To turn on SET BY CUE from the panel, press the ASSIGN

MODE [DCA] key and then turn on the DCA group 7/8

[CUE] key.

E CLEAR

This button clears all output channels assigned to that

DCA group.

F MUTE

These buttons switch muting on/off for DCA groups 7/

8. They are linked with DCA [MUTE] keys 7/8 in the

DCA strip of the panel.

G DCA faders

These faders adjust the levels of DCA groups 7/8. They

are linked with DCA faders 7/8 in the DCA strip.

H CUE

These buttons cue-monitor DCA groups 7/8. They are

linked with DCA [CUE] keys 7/8 in the DCA strip of

the panel.

I DCA LEVEL SET

Use the following two buttons to operate DCA groups

7/8 together.

• ALL NOMINAL

Clicking this button will move DCA faders 7/8 to nom-

inal level (0 dB).

• ALL MINIMUM

Clicking this button will move DCA faders 7/8 to the

–∞ dB position.

Here you can specify the output channels that will be

assigned to mute groups 1–8. Muting can be switched on/

off together for channels assigned to the same mute group.

A Mute group

This area shows the mute group number. The number

corresponding to the grid where the cursor is located is

highlighted.

B MUTE (Mute master)

These buttons switch muting on/off for each mute

group. These buttons are linked with the SCENE

MEMORY [1]–[8] keys of the panel (if the MUTE

MASTER button is On in the constantly-shown area at

the bottom of the display).

Hint

When you turn muting on, channels belonging to that mute

group will behave just as though their panel [ON] key had

been turned off; no signal will be output. During this time, the

panel [ON] key LED will blink.

C Grid

This grid lets you assign output channels (horizontal

rows) to mute groups (vertical columns). Currently-

patched grids are indicated by a symbol. Move the

cursor to the desired grid and press the [ENTER] key

(or click) to set/cancel the assignment.

MUTE GROUP ASSIGN screen

MUTE GROUP ASSIGN

321

OUTPUT DCA/GROUP function

260 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

D MUTE SAFE

These buttons temporarily defeat the muted state of a

channel. When a button is displayed as “–”, clicking it

will change its display to “ON,” and the corresponding

output channel will be excluded from mute groups.

Clicking the button once again restores the original

state.

Note

Normally, Mute Safe operations can be performed indepen-

dently of the scene memory.

Hint

Mute groups 1–8 can be used with both input channels and

output channels. Both types of channel can exist in the identi-

cally-numbered mute group.

E SET BY CUE (Assign by [CUE] key)

This specifies whether the [CUE] key will be used to

make/cancel mute group assignments. While the mute

group SET BY CUE button is on, pressing the [CUE]

key of a channel that can be assigned to the corre-

sponding group will assign the channel to the group.

(Press the [CUE] key once again to cancel the

assignment.)

Hint

The SET BY CUE button can be turned on for only one mute

group. This is automatically turned off when you change

screens or turn off the power.

F CLEAR

This button clears all output channels assigned to that

mute group.

G DIRECT RECALL/MUTE MASTER

This is the same function as the DIRECT RECALL/

MUTE MASTER buttons located at the bottom of the

display (➥ p.165).

Here you can specify the output channels that will be

assigned to EQ link groups A–H. EQ parameters are linked

for channels belonging to the same group.

A EQ link group

These are the EQ link group numbers. The number

corresponding to the grid where the cursor is located is

highlighted.

B Grid

This grid lets you assign output channels (horizontal

rows) to EQ link groups (vertical columns). Currently-

patched grids are indicated by a symbol. Move the

cursor to the desired grid and press the [ENTER] key

(or click) to set/cancel the assignment.

Hint

• The MIX channels and STEREO A/B channels can be

assigned only to EQ link groups A–F, and MATRIX chan-

nels can be assigned only to EQ link groups G/H.

• Grey areas in the grid indicate combinations that cannot be

assigned.

• Input channels and output channels use separate EQ link

groups. Output channels use groups A–H, and input chan-

nels use groups 1–8.

EQ LINK ASSIGN screen

EQ LINK ASSIGN

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 261

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

C SET BY CUE (Assign by [CUE] key)

This specifies whether the [CUE] key will be used to

make/cancel EQ link group assignments. While the EQ

link group SET BY CUE button is on, pressing the

[CUE] key of a channel that can be assigned to the cor-

responding group will assign the channel to the group.

(Press the [CUE] key once again to cancel the

assignment.)

Hint

The SET BY CUE button can be turned on for only one EQ

link group. This is automatically turned off when you change

screens or turn off the power.

D CLEAR

This button clears all output channels assigned to that

EQ link group.

Here you can specify the output channels that will be

assigned to compressor link groups A–H. Compressor

parameters are linked for channels belonging to the same

group.

A Compressor link group

This area shows the compressor link group number.

The number corresponding to the grid where the cur-

sor is located is highlighted.

B Grid

This grid lets you assign output channels (horizontal

rows) to compressor link groups (vertical columns).

Currently-patched grids are indicated by a symbol.

Move the cursor to the desired grid and press the

[ENTER] key (or click) to set/cancel the assignment.

Hint

Input channels and output channels use separate compres-

sor link groups. Output channels use groups A–H, and input

channels use groups 1–8.

COMP LINK ASSIGN (Compressor link

assign) screen

COMP LINK ASSIGN

MATRIX/ST function

262 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

C SET BY CUE (Assign by [CUE] key)

This specifies whether the [CUE] key will be used to

make/cancel compressor link group assignments.

While the compressor link group SET BY CUE button

is on, pressing the [CUE] key of a channel that can be

assigned to the corresponding group will assign the

channel to the group. (Press the [CUE] key once again

to cancel the assignment.)

Hint

The SET BY CUE button can be turned on for only one com-

pressor link group. This is automatically turned off when you

change screens or turn off the power.

D CLEAR

This button clears all output channels assigned to that

compressor link group.

MATRIX/ST function

Here you can send the signal from MIX channels and STE-

REO A/B channels to the STEREO bus or the desired

MATRIX bus.

A MATRIX bus

This is the number of the MATRIX bus to which the

signal is sent. Paired MATRIX channels are indicated

by a heart symbol displayed between them. You can

click this symbol to enable/disable pairing.

B Send level

These knobs specify the send level of each signal that is

sent from the MIX channel or STEREO A/B channel

(vertical column) to the MATRIX buses (horizontal

row).

The knobs shown in this area will depend on how the

MATRIX channels are paired.

MATRIX/ST ROUTING screen

MATRIX/ST ROUTING

MIX channel

STEREO A/B channel

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 263

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

❏ If the MATRIX channels are used individually ❏ If the MATRIX channels are paired

LEVEL knobs

Adjust the send level of the signals sent

from the MIX channels and STEREO A/B

channels to each MATRIX bus.

MIX channel 2

↓

MATRIX bus 2

MIX channel 2

↓

MATRIX bus 1

MIX channel 1

↓

MATRIX bus 1

MIX channel 1

↓

MATRIX bus 2

……

MATRIX 1

MATRIX 2

FADER

MIX CHANNEL 1

MATRIX1

LEVEL

MATRIX2

LEVEL

FADER

MIX CHANNEL 2

MATRIX1

LEVEL

MATRIX2

LEVEL

PAN knobs

Adjust the panning of the signals

sent from the MIX channels and

STEREO A/B channels to each

pair of adjacent odd-numbered/

even-numbered MATRIX buses.

MIX channel 2

↓

MATRIX buses 1/2

MIX channel 1

↓

MATRIX buses 1/2

LEVEL knobs

Adjust the send level of

the signals sent from

the MIX channels and

STEREO A/B channels

to each MATRIX bus.

PAN

to MATRIX 1/2

LEVEL

……

MATRIX 1

MATRIX 2

FADER

MIX CHANNEL 1

PAN

to MATRIX 1/2

LEVEL

FADER

MIX CHANNEL 2

MATRIX/ST function

264 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

C MIX TO MATRIX ON/OFF

This button is an on/off switch for the signal sent from

each MIX channel or STEREO A/B channel to the

MATRIX buses. If this button is off, no signal will be

sent from that channel to the MATRIX buses.

D PRE FADER/POST FADER/POST ON

These buttons select the position from which the sig-

nal is sent from the MIX channel or STEREO A/B

channel to the MATRIX buses, from the following

choices.

This parameter applies to the signal sent from the cor-

responding channel to all MATRIX buses.

E MIX TO STEREO ON/OFF

This button is an on/off switch for the signal sent from

each MIX channel to the STEREO bus. If this button is

off, no signal will be sent from that channel to the STE-

REO bus.

F PRE/POST (Pre-on/Post-on)

This button selects the position from which the signal

is sent from the MIX channel to the STEREO bus, from

the following choices.

G PAN (MIX→STEREO pan)

This knob specifies the panning of the signal sent from

the MIX channel to the STEREO bus. If a MIX chan-

nel is selected in the SELECTED CHANNEL section,

the STEREO [PAN] encoder is linked with this knob.

Hint

If the source is a STEREO A/B channel, parameters

–

are not displayed.

H MIX channel, STEREO A/B channel

This area indicates the MIX channel or STEREO A/B

channel from which the signal is being sent. Paired

MIX channels are indicated by a heart symbol dis-

played between them. You can click this symbol to

enable/disable pairing.

This screen lists the signals sent from the MIX channels to

the MATRIX buses. You can also edit the settings from

within this screen.

A MIX to MTRX/MTRX from MIX

Select one of the following two types of screen display.

❏ When the MIX to MTRX button is on

You can view the status of the signals sent from a spe-

cific MIX channel or STEREO A/B channel to all

MATRIX buses.

PRE FADER Immediately before the fader

POST FADER Immediately after the fader

POST ON

Immediately after the MIX [ON] key / STE-

REO [ON] key

PRE

Immediately before the MIX [ON] key

(immediately after the fader)

POST Immediately after the MIX [ON] key

MIX to MATRIX VIEW screen

MIX to MATRIX VIEW

1 2

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 265

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

❏ When the MTRX from MIX button is on

You can view the status of the signals sent from all MIX

channels or STEREO A/B channels to a specific

MATRIX bus.

B SEND LEVEL/SEND POINT

Select one of the following two parameters to view in

the grid.

❏ When the SEND LEVEL button is on

The send levels sent from the MIX channels or STE-

REO A/B channels to the MATRIX buses will be shown

as a bar graph in each grid. Channels for which the sig-

nal sent to the MATRIX bus is turned off are shown by

gray bars, and channels for which the signal is turned

on are shown by blue bars.

To edit the send level, move the cursor to the grid

where the MIX or STEREO A/B channel (vertical col-

umn) intersects the MATRIX bus (horizontal row),

and turn the [DATA] encoder.

To switch the signal sent from a specific MIX or STE-

REO A/B channel to the MATRIX buses on/off, move

the cursor to the vertical column for that channel, and

press the [ENTER] key.

Hint

• If the send level is set above nominal (0 dB), a red line indi-

cating nominal level is displayed.

• If the send-destination MATRIX channel is paired, the grid

for the odd-numbered MATRIX bus will show an orange line

indicating the pan value instead of a bar graph. (In MTRX

from MIX mode, upward indicates R, and downward indi-

cates L.)

If the SEND LEVEL button is on, you can select a

desired grid and copy its send level (pan) value to other

channels (horizontal direction) or to other MATRIX

buses (vertical direction), or switch all grids on/off

simultaneously.

To do so, move the cursor to the desired grid; then

hold down the [SHIFT] key and press the [ENTER]

key. (Alternatively, hold down the [SHIFT] key and

click the desired grid.) When the JOB SELECT win-

dow appears, select one of the following choices to

copy, and click the OK button.

LEVEL COPY [ALL MATRIX ]

Copy the send level (pan) value of the selected grid to

all send level (pan) settings of the corresponding MIX

(or STEREO A/B) channel in the vertical direction of

the grid.

Note

If the selected grid is a send level, only the send levels will be

copied. If the selected grid is a pan value, only the pan values

will be copied.

LEVEL COPY [ALL MIX ]

Copy the send level (pan) value of the selected grid to

all send level (pan) settings of the corresponding

MATRIX bus in the horizontal direction of the grid.

LEVEL COPY [ALL MIX x ALL MATRIX]

Copy the send level (pan) value of the selected grid to

the send level (pan) settings of all MIX (and STEREO

A/B) channels and MATRIX buses.

ALL ON [ALL MIX ]

Turn on the signals sent from all channels (MIX,

STEREO A/B) to the corresponding MATRIX bus.

ALL OFF [ALL MIX ]

Turn off the signals sent from all channels (MIX,

STEREO A/B) to the corresponding MATRIX bus.

❏ When the SEND POINT button is on

The grid will show the position from which the signal is

sent from the MIX channels or STEREO A/B channels

to the MATRIX buses.

Each indication has the following significance.

(yellow) . . PRE FADER (immediately

before the fader)

(gray) . . . . POST FADER (immediately

after the fader)

(red) . . . . . POST ON (immediately after

the [ON] key)

Channels for which the

signal sent to the MATRIX

bus is turned on (blue bar

graph)

Channels for which the

signal sent to the MATRIX

bus is turned off (gray bar

graph)

Pan value (orange line)

PRE FADER POST FADER POST ON

MATRIX/ST function

266 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

To change the position from which the signal is sent,

move the cursor to the vertical column for the desired

channel, and press the [ENTER] key, click, or turn the

[DATA] encoder. (The position of all signals sent from

that channel to all MATRIX buses will change

simultaneously.)

If the SEND POINT button is on, the send position for

all grid locations can be changed simultaneously. To do

so, hold down the [SHIFT] key and click the desired

grid. (Alternatively, move the cursor to the desired

grid; then hold down the [SHIFT] key and press the

[ENTER] key.) When the JOB SELECT window

appears, select one of the following choices, and click

the OK button.

ALL PRE FADER [ALL MIX ]

All grids will be set to PRE FADER.

ALL POST FADER [ALL MIX ]

All grids will be set to POST FADER.

ALL POST ON [ALL MIX ]

All grids will be set to POST ON.

C Grid

The grid shows various settings for the signals sent

from the MIX or STEREO A/B channels (vertical col-

umns) to the MATRIX buses (horizontal rows). The

red lines shown in the upward, downward, left, and

right directions indicate the channel (MIX or STEREO

A/B) and MATRIX bus corresponding to the grid

where the cursor is located.

D SELECTED PARAMETER (currently selected

parameter)

This area indicates the channel (MIX or STEREO A/B)

and MATRIX bus corresponding to the grid where the

cursor is currently located. The four boxes at right

indicate the values for the grid where the cursor is cur-

rently located.

Send level

Pan (displayed if the

destination MATRIX

channel is paired)

Position from which

the signal is sent

On/off switch for the signal

sent to the MATRIX bus

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 267

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

Here you can make settings for LCR mode, which allows

three-channel playback by adding a CENTER channel to

the L/R channels of the STEREO bus. This function can be

used only with MIX channels.

A Response graph

These graphs indicate the approximate LCR response

for each MIX channel. The graph will change as the

CSR knob (

2) is edited.

B CSR (Center Side Ratio)

This knob adjusts the proportional level of the CEN-

TER channel relative to the L/R channels. The range is

0–100%.

If the CSR knob is set to 0%, turning the PAN knob in

the MIX TO STEREO area of the MATRIX/ST ROUT-

ING screen (or the [PAN] encoder in the SELECTED

CHANNEL section) will change the signal levels of the

L/R channels as shown below.

In this case, MIX TO STEREO PAN will operate as a

conventional PAN control, and no signal will be sent to

the CENTER channel.

If CSR is set to 100%, turning the PAN knob ([PAN]

encoder) will change the signal levels of the L/R chan-

nels as shown below.

When the PAN knob ([PAN] encoder) is in the center

position, the signal level of the CENTER channel will

be at maximum, and no signal will be sent to the L/R

channels.

C LCR (LCR mode on/off)

For each MIX channel, this turns LCR mode on/off.

For channels where LCR mode is turned on, the PAN

knob in the MIX TO STEREO area of the MATRIX/ST

ROUTING screen can be used to simultaneously con-

trol the levels of the L/R channels and the CENTER

channel.

If you have selected a MIX channel for which LCR is

on, you can also use the [PAN] encoder in the

SELECTED CHANNEL section of the top panel. In

this case, the peripheral LEDs will change as follows

when you operate the [PAN] encoder.

• When LCR = off

• When LCR = on

Note

In order to use the LCR function, the USE AS CENTER BUS

button must be turned On in the MIXER SETUP screen (SYS/

W.CLOCK function) (

➥

p.222). Be aware that when this but-

ton is on, the CENTER channel signal is not sent to the

STEREO B bus, and will not play back appropriately. (In this

case, the STEREO B bus is sent the same signal as the STE-

REO A bus.)

LCR screen

LCR

CRL

Signal sent to the

R channel

[PAN] encoder

Signal sent to the

L channel

Signal level

CRL

[PAN] encoder

Signal sent to the

R channel

Signal sent to the

C channel

Signal sent to the

L channel

Signal level

RLRL RL

MATRIX/ST function

268 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

D MIX channel

This is the number and name of the MIX channel you

are editing. Paired MIX channels are indicated by a

heart symbol displayed at the right. You can click this

symbol to enable/disable pairing. The values of param-

eters

2–3 are linked for paired channels.

Hint

• The master level of the CENTER channel is controlled by

the STEREO B channel fader. You can also use the STE-

REO B channel EQ and compressor to process the signal.

• Use either one of the output jacks patched to the STEREO B

channel as the output jack for the CENTER channel. (When

the USE AS CENTER BUS button is On in the MIXER

SETUP screen, the L/R channels of the STEREO B bus out-

put the same signal.)

• By selecting LCR as the monitor source, you can monitor

the LCR signal from the MONITOR OUT jacks L/C/R.

Here you can make various settings related to surround

functionality, such as selecting the surround mode, and

assigning MIX buses to surround channels.

A SURROUND MODE

Choose one of the follow-

ing as the surround mode

when using the Surround

Pan function (➥ p.142).

This is the same as the

SURROUND MODE in

the MIXER SETUP screen

(SYS/W.CLOCK func-

tion). The graphic below

the buttons will change

according to the mode you

select.

• STEREO

This is conventional stereo

mode.

• 3-1ch

This mode uses four chan-

nels: L (front left), C (front

center), R (front right),

and S (surround).

• 5.1ch

This mode uses six channels: L (front left), C (front

center), R (front right), Ls (rear left), Rs (rear right),

and LFE (subwoofer).

• 6.1ch

This mode uses seven channels: 5.1ch with the addi-

tion of Bs (rear center).

Hint

If 3-1ch, 5.1ch, or 6.1 ch is selected as the surround mode,

MIX buses 1–8 or 9–16 are used as surround buses, starting

with the earlier-numbered buses. (Buses not used as sur-

round buses can be used as conventional buses.) These MIX

buses cannot be used as conventional bus outputs until you

return to stereo mode.

SURR SETUP screen

SURR SETUP

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 269

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

B Bus assignments

This area indicates the surround channels assigned to

the MIX buses that are being used as surround buses.

You can edit these settings by clicking the / but-

tons at the left and right.

When you change the surround channel assignment,

the MIX bus whose channel assignment you changed

will be exchanged with the MIX bus that had been pre-

viously assigned to that channel.

Note

The MIX buses used are fixed for each surround mode.

For surround mode 3-1, MIX buses 1–4 or 9–13 can be used.

For surround mode 5.1, MIX buses 1–6 or 9–14 can be used.

For surround mode 6.1, MIX buses 1–7 or 9–15 can be used.

Other MIX buses can be used as conventional MIX buses.

However in the case of 6.1, MIX bus 8 or MIX bus 16 are

always handled as FIXED buses.

C INIT (Initialize)

For each surround mode, this restores the surround

channel assignments to the MIX buses to their initial

state.

D SURROUND BUS ALLOCATION

Select either MIX buses 1–8 or 9–16 as the range of

MIX buses used as surround buses.

E DELAY

This specifies the delay time for each surround channel

in a range of 0–1000 msec. The current value is shown

by the two boxes below the knob. (The upper box

shows the delay time in millisecond units, and the

lower box shows the delay time in the units selected in

the MIX 1-24 screen of the OUT DELAY function.)

F DELAY ON/OFF

Turns the delay on/off for each surround channel.

G FADER (Fader level)

Adjusts the level of the signal sent from the surround

channel to the corresponding MIX bus in a range of

–∞ to +10 dB. The current value is shown in the box

below.

H CUE

This button lets you cue-monitor the surround chan-

nel. This is linked with the [CUE] key of the

corresponding MIX channel.

I ON/OFF (Channel on/off)

Turns the surround channel on/off. This is linked with

the MIX [ON] key of the corresponding MIX channel.

J Level meter

Indicates the output level of the surround channel.

K Surround channel

This is the name of the surround channel.

2 3 4

5 7 8 J

OUTPUT VIEW function

270 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

OUTPUT VIEW function

This screen displays the mix parameters of the currently

selected MIX channel, MATRIX channel, or STEREO A/B

channel. In this screen you can also edit the principal

parameters and access other screens.

A Channel

This is the number of the channel you are editing. If

the corresponding MIX/MATRIX channel is paired (or

if a STEREO A/B channel is selected), a heart symbol is

displayed at the right. You can click this symbol to

enable/disable pairing for the MIX/MATRIX channel.

Note

The screen shown above is for when a paired channel is

selected. If the selected channel is not paired, the parameters

for only one channel are displayed, and pairing-related set-

tings are not displayed.

B EQ

This area shows the post-EQ level, the approximate EQ

response, and the EQ on/off status. You can click the

EQ ON/OFF button to switch EQ on/off in this screen.

If you click the mini-graph, the EQ PARAM screen for

that channel will appear.

C Compressor

This area shows the amount of gain reduction and the

output level of the compressor, a mini-graph showing

the approximate response of the compressor, and the

compressor on/off status. You can click the COMP

ON/OFF button to switch the compressor on/off in

this screen. If you click the mini-graph, the COMP

PARAM screen for that channel will appear.

D Insert in

This area indicates the insert point, the insert on/off

status, and the type and input level of the port that is

patched to insert-in. You can click the INSERT ON/

OFF button to switch insertion on/off in this screen.

If an internal effect is patched, the effect type and

BYPASS button are displayed. If a GEQ module is

patched, the GEQ ON/OFF button and a mini-graph

showing the GEQ response are displayed.

E DELAY

In this area you can view and edit the delay time of the

internal delay and its on/off status.

F TO MATRIX (only for MIX channels and

STEREO A/B channels)

This area shows the send level, send position, and on/

off status of the signals sent from the corresponding

MIX channel or STEREO A/B channel to MATRIX

buses 1–8. You can also edit the send level, send posi-

tion, and on/off status in this screen. Here’s how to do

this.

• To edit the send level of signals sent to the MATRIX

bus

Move the cursor to the desired bar graph in the list,

and turn the [DATA] encoder.

• To edit the send position of signals sent to the

MATRIX bus

Click either the PRE FADER, the POST FADER, or the

POST ON button located below.

Alternatively, you can edit the setting by moving the

cursor to the PRE or POST indication in the list and

pressing the [ENTER] key or turning the [DATA]

encoder.

CH VIEW (Channel view) screen

CH VIEW

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 271

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

• To switch the signal sent to the MATRIX bus on/off

Click the ON/OFF button located below.

You can also switch this on/off by moving the cursor to

a bar graph in the list and pressing the [ENTER] key.

The bar graph is colored blue when on, and gray when

off.

G DCA group / Mute group

Here you can assign or cancel DCA group and MUTE

group assignments.

H RECALL SAFE / MUTE SAFE

Here you can enable or disable Recall Safe and Mute

Safe settings.

I TO STEREO (MIX channels only)

Here you can switch the signal sent from a MIX chan-

nel to the STEREO bus on/off, and edit its panning and

send position (pre-on / post-on) (➥ p.264).

J BALANCE (only for paired MIX/MATRIX

channels and STEREO A/B channels)

This adjusts the left/right volume balance of the signals

output from paired MIX channels or STEREO A/B

channels.

K LCR (MIX channels only)

Here you can switch LCR mode on/off, and adjust CSR

(the level of the CENTER channel relative to the L/R

channels) (➥ p.267).

L LIBRARY

This button accesses the OUTPUT CH LIBRARY

screen (➥ p.275), where you can store/recall library

settings for output channels.

M Level meter

This level meter indicates the output level of the

channel.

N Signal detection point

This is the point at which the signal level shown in the

level meter (

M) is detected (PRE EQ, PRE FADER,

POST FADER, POST DELAY, or POST ON). You can

edit this setting by clicking the / buttons at the left

and right.

O Fader

This controls the output level of the channel.

P CUE

This button cue-monitors the signal of the channel.

This is linked with the [CUE] key of the corresponding

channel.

Q ON/OFF (Channel on/off)

This is an on/off switch for the signal that is output

from the channel. This is linked with the [ON] key of

that channel.

OUTPUT VIEW function

272 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

This screen shows the signal flow for adjacent odd-num-

bered/even-numbered MIX/MATRIX channels or for

STEREO A/B channels. In this screen you can also edit

some of the parameters, and access other screens. You can

also determine the location within the signal flow at which

clipping occurred.

A Channels

These are the numbers and names of the channels you

are editing. By clicking the / buttons at left and

right, you can switch the display in units of two

channels.

If the corresponding MIX/MATRIX channels are

paired (or if a STEREO A/B channel is selected), a heart

symbol is displayed at the right. You can click this sym-

bol to enable/disable pairing for the MIX/MATRIX

channels.

B Insert

This area displays insert-related information for the

two selected channels (insert point, the ports patched

to insert in/out, and insert on/off status).

Here you can also select the insert point (use the /

buttons at left and right), or switch insertion on/off

(use the ON/OFF button).

C Level meters

These meters indicate the levels within the signal flow.

Levels are detected at the following locations.

• EQ (immediately before and after the EQ)

• COMP (immediately before and after the

compressor)

• FADER (immediately before and after the fader)

• DELAY (immediately before and after the delay)

• INSERT IN (immediately after the insert point)

D Signal flow

This area indicates the signal flow of the selected chan-

nel. The following parameters are displayed.

• EQ (Equalizer)

This indicates the EQ on/off status and the approxi-

mate response curve. You can click the EQ button to

switch EQ on/off, or click the mini-graph to access the

EQ PARAM screen for the corresponding channel.

• COMP (Compressor)

This indicates the compressor on/off status and the

approximate response curve. You can click the COMP

button to switch the compressor on/off, or click the

mini-graph to access the COMP PARAM screen for the

corresponding channel.

• FADER

This indicates the output level of the channel. This is

linked with the encoder or fader of the corresponding

channel.

• ON/OFF (On/off)

Turns the channel on/off. This is linked with the [ON]

key of the corresponding channel.

• DELAY

Here you can switch the internal delay on/off and edit

the delay time.

Hint

• If insert is enabled, the currently selected insert point is

shown in this signal flow.

• If the signal clips, the signal flow (horizontal line) after clip-

ping is displayed in red. If an output is turned off so that the

signal does not flow any further, the subsequent flow is dis-

played in gray. If PEAK HOLD is on, the flow indication will

stay red if clipping occurs even once, making it easier to see

that clipping has occurred.

SIGNAL FLOW screen

SIGNAL FLOW

1 2

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 273

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

E TO MATRIX (only for MIX channels and

STEREO A/B channels)

This area shows the on/off status of the signal sent

from the MIX channel or STEREO A/B channel to the

MATRIX buses, and the point from which the signal is

sent.

F TO STEREO (MIX channels only)

This area shows the pan, the send position, and the on/

off status of the signal sent from the MIX channel to

the STEREO bus.

This screen shows the on/off status, level, and cue monitor

status of the output channels and DCA groups.

A ON/OFF (On/off)

Here you can switch output channels on/off, and

switch DCA group muting on/off. These settings are

linked with the [ON] keys of the corresponding chan-

nels and the [MUTE] keys of the DCA groups.

B Level

Here you can adjust the level of the output channels

and DCA groups. The current value is shown in the

box immediately below. These are linked with the

encoder or fader of the corresponding channel or DCA

group.

C Cue

Here you can switch cue monitoring on/off for output

channels and DCA groups. These are linked with the

[CUE] key of the corresponding channel or DCA

group.

FADER VIEW screen

FADER VIEW

OUTPUT VIEW function

274 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

In this screen you can copy the desired parameter(s) from

the selected output channel into a memory buffer, and

paste the same type of channel (you may select more than

one paste-destination).

A JOB SELECT

• COPY

The copy-source channel will remain; its parameters

will be copied to another channel.

Note

You cannot turn off the COPY button.

B CAPTURE

When you click this button, the settings of the cur-

rently selected channel will be copied to a temporary

memory buffer.

If the corresponding MIX/MATRIX channel is paired

(or if a STEREO A/B channel is selected), a heart sym-

bol is displayed at the right.

C BUFFERED CH (Channel in the buffer)

This shows the channel that is currently copied into

buffer memory.

Note

• The same buffer memory is used to copy channel settings

for both input channels and output channels.

• If input channel settings have been copied to the buffer

memory, a message of “TYPE CONFLICT!” is displayed

below, and you cannot paste to an output channel.

• The contents of the buffer memory are erased when the

PM5D is powered-off.

D EXECUTE

When you click this button, the specified parameters

will be copied from buffer memory to the specified

paste-destination channel.

If an input channel is copied to buffer memory, or if no

paste-destination has been specified, this is grayed-out

and the Paste operation is unavailable.

E PARAMETER SELECT

Here you can select the parameter(s) that will be

pasted. You can select the following parameters.

If the TO MTRX button is on, you can use the

MATRIX buttons (1–8) to select the applicable

MATRIX buses.

CH JOB (Channel job) screen

CH JOB

ALL All parameters

EQ EQ function settings

COMP COMP function settings

DELAY DELAY function settings

FADER Fader level

ON CH [ON] key on/off status

BAL Balance settings

INSERT Insert on/off status and insert point

TO MTRX Send level to the desired MATRIX bus(es)

DCA Associated DCA group

MUTE Associated mute group

LCR LCR screen settings

WITHOUT

MIX SEND/

WITH MIX

SEND

Selects whether the send level sent from

input channels to the selected MIX bus will

be included (WITH...) or will not be included

(WITHOUT...) in the pasted data.

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 275

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

F CH SELECT (Channel selection)

Here you can select the paste-destination channel(s).

You can only select channels of the same type as the

copy-source.

Hint

If the copy-source MIX/MATRIX channel is paired, the odd-

numbered channel is copied to the odd-numbered channel(s),

and the even-numbered channel is copied to the even-num-

bered channel(s).

G SET ALL

Specifies the paste-destination as all channels of the

same type as the copy-source.

H CLEAR ALL

De-selects all channels.

Here you can recall, store, rename, or delete items in the

output channel library.

A EDIT

When you click this button, the CH VIEW screen

(OUTPUT CH VIEW screen) for the currently selected

output channel will appear.

B Channel

This is the number and name of the channel you will

store or recall.

Note

• Channel library store/recall operations are performed in units

of one channel.

• If the channel selected by the [SEL] key is paired (or if a

STEREO A/B channel is selected), the operation will apply

to only one of the currently selected channels (in the case of

STEREO A/B, only the L or the R channel).

• When you recall a channel library item into one of a pair of

MIX/MATRIX channels (or into L or R of the STEREO A/B

channel), any linked parameters will be copied to the other

channel.

C LIBRARY TYPE (Channel type)

Indicates the type of the currently selected channel. If a

MIX or STEREO A/B channel is selected, the pairing

configuration of MATRIX buses 1–8 is shown immedi-

ately below.

OUTPUT CH LIBRARY screen

OUTPUT CH LIBRARY

OUTPUT VIEW function

276 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

D RECALL

Recalls the channel library item selected in the list into

memory.

If the channel selected in (

1) is of a different type than

the channel selected in the list, this button is grayed-

out and the Recall operation is unavailable. (However,

Initial Data can be recalled to any output channel.)

E STORE

Stores the settings of the currently selected output

channel into the location selected in the list. When you

click this button a window will appear, allowing you to

name and save the settings.

F TITLE EDIT

Edits the title of the library item selected in the list.

When you click this button a window will appear,

allowing you to edit the title.

G CLEAR

Deletes the library item selected in the list. When you

click this button, a confirmation message will appear.

Note

Library items with an “R” displayed in the right column of the

list are read-only. Read-only items cannot be stored,

renamed, or deleted.

H LIBRARY TYPE

Displays the type of channel for the library item

selected in the list. If the channel selected in (

1) is of a

different type than the channel selected in the list, a

message of “CONFLICT!” is displayed at the right and

the Recall operation is unavailable.

If a MIX or STEREO A/B channel is selected, the pair-

ing configuration of MATRIX buses 1–8 is shown

immediately below.

I Library list

Use the scroll bar to select the library item on which

you want to perform an operation. The selected library

item will move to the center, and will be highlighted.

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 277

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

INPUT PATCH function

Here you can assign input ports (INPUT jacks, ST IN

jacks, 2TR IN DIGITAL/ANALOG jacks, input channels of

slots, outputs of internal effects) to input channels.

A SELECTED PATCH

This indicates the name and number of the input chan-

nel at which the cursor is located, and the input port.

B CH (Input channel)

This is the number and name of the input channel

(input channel, ST IN channel, FX RTN channel)

assigned to the input port. The channel number at

which the cursor is located will be highlighted. If you

click the name, a window will open allowing you to

assign a name to the channel.

C ASSIGN

For each channel, this indicates the number (1 or 0) of

input ports currently assigned.

D Grid

This grid lets you patch input ports (horizontal rows)

to input channels (vertical columns). Currently-

patched grids are indicated by a symbol. By clicking

a grid location you can set/cancel patching.

The red lines at the left and top indicate the grid loca-

tion to which you move the cursor.

Hint

• If PATCH CONFIRMATION is turned on in the PREFER-

ENCE 1 screen (UTILITY function), a confirmation message

will appear each time you attempt to change a patch set-

ting. If STEAL PATCH CONFIRMATION is turned on, a

confirmation message will also appear when you attempt to

make patch settings that would cause an existing patch to

be modified.

• To move the cursor location rapidly in or out of the grid, hold

down the [SHIFT] key and press the CURSOR [

√

]/[

[

†

] keys.

• To move rapidly to left or right inside the grid, turn the

[DATA] encoder. To move up or down, hold down the

[SHIFT] key and turn the [DATA] encoder.

Note

You can patch multiple input channels to a single input port,

but you cannot patch multiple input ports to a single input

channel.

E Input port

From the top, this area indicates the type of input port,

the ID number, the input channel number, and the

number of input channels assigned. The following

types of input port can be selected.

Hint

• The port number is grayed-out for ports that are currently

unavailable.

• If the CASCADE connector is being used as a SLOT IN port,

the port number of the CASCADE connector is displayed in

yellow instead of the SLOT IN port number.

Input functions

INPUT PATCH screen

INPUT PATCH

3 4

AD IN INPUT jacks 1–48

AD STIN L/R channels of ST IN jacks 1–4

SLOT IN

Input channels of an I/O card installed in

slots 1–4

FX OUT L/R outputs of internal effects 1–8

2TR IN

L/R channels of 2TR IN DIGITAL jacks 1–3

and 2TR IN ANALOG jacks 1/2

INPUT PATCH function

278 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

F PRESET

This button resets the input port → input channel

assignments to the following default settings.

G CLEAR ALL

This button clears all assignments of input ports to

input channels.

H VIRTUAL SOUNDCHECK

Here you can make settings for the virtual soundcheck

function, which temporarily switches the input patch-

ing. For details, refer to the explanation of the SYS/

W.CLOCK function MIXER SETUP screen (➥ p.221).

I LIBRARY

This button accesses the INPUT PATCH LIBRARY

screen (➥ p.283), where you can store/recall input

channel patch library settings.

Here you can patch an input channel to an output port so

that the input signal will be output directly from that port.

A SELECTED PATCH

This indicates the name and number of the input chan-

nel at which the cursor is located, and the output port.

B CH (Input channel)

This is the number and name of the input channel

(input channel, ST IN channel) for assignment to an

output port. The channel number at which the cursor

is located will be highlighted. If you click the name, a

window will open allowing you to assign a name to the

channel.

C ASSIGN

For each channel, this indicates the number of output

ports that are currently assigned.

D Grid

This grid lets you patch input channels (vertical col-

umns) to output ports (horizontal rows). Currently-

patched grids are indicated by a symbol. By clicking

a grid location you can set/cancel patching.

The red lines at the left and top indicate the grid loca-

tion to which you move the cursor.

Hint

Operations in the grid are the same for all of the patching

screens. For details, refer to the Hint on p.277.

Channel Input port

Input channels 1–48 AD IN 1–48

ST IN channels 1–4 L/R AD STIN L/R

FX RTN channels 1–4 L/R FX OUT 1–4 L/R

6 7 98

DIRECT OUT PATCH screen

DIRECT OUT PATCH

3 4

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 279

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

E Output port

From the top, this area indicates the type of output

port, the ID number, the output channel number, and

the number of input channels assigned. The following

types of output port can be selected.

Hint

• The port number is grayed-out for ports that are currently

unavailable.

• For SLOT OUT ports that are also being output to the CAS-

CADE connector, the port number of the CASCADE

connector is displayed in yellow instead of the SLOT OUT

port number.

F LIBRARY button

This button accesses the INPUT PATCH LIBRARY

screen (➥ p.283), where you can store/recall input

channel patch library settings.

Note

To enable direct output from the selected port, you will need to

make settings in the INSERT/DIRECT OUT POINT screen

(INPUT PATCH function) to turn on direct output for the corre-

sponding input channel (

➥

p.281).

In this screen you can patch the input/output ports by

which external devices will be inserted into each input

channel. Select the output port in the left side of the screen,

and the input port in the right side of the screen.

A SELECTED PATCH

This indicates the number and name of the input chan-

nel at which the cursor is located in the grid.

B Insert in/out

This indicates the input/output ports that are patched

as insert in/out for the input channel at which the cur-

sor is located.

C CH (Input channel)

This area shows the number and name of each input

channel (input channel, ST IN channel L/R). The

channel number at which the cursor is located will be

highlighted. If you click the name, a window will open

allowing you to assign a name to the channel.

D ASSIGN

For each input channel, this indicates the number of

output ports that are currently assigned as insert-out.

SLOT OUT

Output channels of an I/O card installed in

slots 1–4

2TR OUT

L/R channels of 2TR OUT DIGITAL jacks

1–3

INSERT PATCH screen

INSERT PATCH

4 5

INPUT PATCH function

280 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

E Grid

For each input channel (vertical column), this grid lets

you can patch one or more output ports (horizontal

row) to be used as insert-outs. Currently-patched grids

are indicated by a symbol.

By clicking a grid location you can set/cancel patching.

The red lines at the left and top indicate the grid loca-

tion to which you move the cursor.

Hint

Operations in the grid are the same for all of the patching

screens. For details, refer to the Hint on p.277.

F Output port

From the top, this area indicates the type of output

port, the ID number, the output channel number, and

the number of input channels assigned. The following

types of output port can be patched as insert-out.

Hint

• The port number is grayed-out for ports that are currently

unavailable.

• For SLOT OUT ports that are also being output to the CAS-

CADE connector, the port number of the CASCADE

connector is displayed in yellow instead of the SLOT OUT

port number.

• If you select GEQ IN as an insert-out, the output of the same

GEQ module will automatically be selected as the insert-in.

G Input port

From the top, this area indicates the type of input port,

the ID number, L/R, the input channel number, and

the total number of input channels (including insert-

in) that are patched to each input port. You can select

the following input ports.

H LIBRARY button

This button accesses the INPUT PATCH LIBRARY

screen (➥ p.283), where you can store/recall input

channel patch library settings.

Note

To enable the insert ins/outs that you assigned to input chan-

nels in this screen, you need to turn Insert on for the

corresponding input channel in the INSERT/DIRECT OUT

POINT screen (INPUT PATCH function) (

➥

p.281). However,

insertion is automatically enabled if you assigned insert in/out

to a GEQ.

Hint

When operating from the panel, you can move the cursor from

the right side of the screen to the left side (or vice versa) by

holding down the [SHIFT] key and using the CURSOR [

√

[

] keys.

MIX OUT MIX OUT jacks 1–24

SLOT OUT

Output channels of an I/O card installed in

slots 1–4

FX IN L/R inputs of internal effects 1–8

GEQ IN Inputs of GEQ modules 1–20

2TR OUT

L/R channels of 2TR OUT DIGITAL jacks

1–3

AD IN INPUT jacks 1–48

AD ST IN ST IN jacks 1–4 L/R

SLOT IN

Input channels of an I/O card installed in

slots 1–4

FX OUT L/R outputs of internal effects 1–8

GEQ OUT Outputs of GEQ modules 1–20

2TR IN

L/R channels of 2TR IN DIGITAL jacks 1–3

or 2TR IN ANALOG jacks 1/2

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 281

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

For each input channel, you can specify the point at which

insert in/out will be patched, and the point from which

direct output will be taken. Here you can also switch Insert

or Direct Output on/off.

A Insert view

When you move the cursor to an insert I/O point (4),

the insert and direct output locations for that input

channel will be shown graphically.

B INPUT CH (Input channel)

This is the number of the input channel you are edit-

ing. Two paired channels are indicated by a heart

symbol shown at the left; settings

3–6 will be linked

for these channels. You can click this symbol to enable/

disable pairing.

C INSERT ON/OFF

This button switches insert on/off for each channel.

This is linked for two paired channels.

Note

Be aware that if you turn on this button when either insert-in or

insert-out are unpatched, the signal will no longer be output

from the corresponding input channel.

D INSERT I/O (Insert I/O point)

Here you can select one of the following as the insert-

in/out location for each channel.

E SET ALL

Turns on the corresponding item (insert or the insert

point) for all channels (including channels not cur-

rently shown in the screen).

F CLEAR ALL

Turns insert off for all channels (including channels

not currently shown in the screen).

INSERT/DIRECT OUT POINT screen

INSERT/DIRECT OUT POINT

PRE EQ Immediately before the EQ

POST EQ Immediately after the EQ

PRE DELAY Immediately before the delay

POST FADER Immediately after the fader

INPUT PATCH function

282 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

G DIRECT OUT ON/OFF

These buttons switch direct output on/off for each

channel.

H DIRECT OUT

Here you can select one of the following as the direct

output location for each channel.

I SET ALL

Turns on the corresponding item (direct out or the

direct out point) for all channels (including channels

not currently shown in the screen).

J CLEAR ALL

Turns direct out off for all channels (including chan-

nels not currently shown in the screen).

Here you can assign a name to each input channel and

DCA group.

A Channel

This area indicates the input channel (input channel,

ST IN channel) and DCA group numbers.

B Name

This area indicates the names currently assigned to

each input channel and DCA group. If you click the

name, a window will open allowing you to assign a

name to the channel.

C LIBRARY

This button accesses the INPUT PATCH LIBRARY

screen (➥ p.283), where you can store/recall input

channel patch (and name) library settings.

PRE ATT Immediately before the attenuator

PRE HPF Immediately before the high-pass ﬁlter

PRE EQ

Immediately before the EQ (immediately

after the PRE EQ of the INSERT I/O)

PRE FADER Immediately before the fader

POST ON Immediately after the CH [ON] key

NAME screen

NAME

1 2 3

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 283

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

Here you can recall, store, rename, or delete items in the

input patch library.

Except for the fact that these are patch settings for input

channels, display and operations are the same as in the

OUTPUT PATCH function OUTPUT PATCH LIBRARY

screen. Refer to p.247.

INPUT HA/INSERT function

Here you can make settings for internal HAs (PM5D-RH

model only) or external HAs assigned to input channels.

INPUT PATCH LIBRARY screen

INPUT PATCH LIBRARY

CH 1-24 (Input channel 1-24) screen

CH 25-48 (Input channel 25-48)

screen

STIN/FXRTN (ST IN/FXRTN channel)

screen

CH 1-24

STIN/FXRTN

INPUT HA/INSERT function

284 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

A +48V

B HPF (High Pass Filter)

C Cutoff frequency

D GAIN

E Input port

These items are the same as in the OUTPUT INSERT

function INSERT IN MIX1-24 screen and INSERT IN

MATRIX/STEREO/MONITOR screen (➥ p.248).

F Channel

This area shows the number and name of the channel

you are editing. Two paired channels are indicated by a

heart symbol displayed between them.

Note

• Items

–

are not shown for channels to which nothing is

patched, or for channels patched to an input port that does

not have a HA. Items

and

are not shown for channels

patched to a port that has no high pass filter.

• To assign input ports to input channels, use the INPUT

PATCH screen (INPUT PATCH function).

• HA settings are not linked even if two channels are paired.

However, the GAIN knob setting is linked for HAs whose

GANG button is turned on in the HA screen (SYS/W.CLOCK

function).

G LIBRARY button

This button displays the HA LIBRARY screen

(➥ p.230), where you can store/recall internal HA or

external HA settings as library items.

Hint

The HA settings you edit in this screen are also reflected in

the HA screen (SYS/W.CLOCK function).

Here you can make settings for internal HAs (PM5D-RH

model only) or external HAs assigned to the insert-in of

input channels.

INSERT 1-24 screen

INSERT 25-48 screen

INSERT STIN screen

INSERT 1-24

INSERT STIN

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 285

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

A +48V

B HPF (High Pass Filter)

C Cutoff frequency

D GAIN

E Input port

These items are the same as in the OUTPUT INSERT

function INSERT IN MIX1-24 screen and INSERT IN

MATRIX/STEREO/MONITOR screen (➥ p.248).

F Channel

This area shows the number and name of the channel

you are editing. Two paired channels are indicated by a

heart symbol displayed between them.

Note

• Items

–

are not shown for channels to whose insert-in

nothing is patched, or for channels patched to an input port

whose insert-in does not have a HA. Items

and

are not

shown for channels patched to a port that has no high pass

filter.

• To assign an input port to an insert-in, use the INPUT

PATCH screen (INPUT PATCH function).

• HA settings are not linked even if two channels are paired.

However, the GAIN knob setting is linked for HAs whose

GANG button is turned on in the HA screen (SYS/W.CLOCK

function).

G LIBRARY button

This button displays the HA LIBRARY screen

(➥ p.230), where you can store/recall internal HA or

external HA settings as library items.

Hint

The HA settings you edit in this screen are also reflected in

the HA screen (SYS/W.CLOCK function).

This screen is the same as HA LIBRARY in the SYS/

W.CLOCK function (➥ p.230).

HA LIBRARY screen

HA LIBRARY

INPUT ø/EQ function

286 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

INPUT ø/EQ function

Here you can edit the EQ parameters of the selected input

channel.

A Channel selection

Selects the input channel (input channel 1–48, STIN

channel 1–4 L/R, FXRTN channel 1–4 L/R).

B Name

This is the name of the currently selected input chan-

nel. If the input channel is paired (or if a ST IN channel

or FX RTN channel is selected), a heart symbol is dis-

played at the right. For an input channel, you can click

this symbol to enable/disable pairing.

C EQ ON/OFF

Turns the EQ on/off for that channel.

D EQ LINK GROUP

Selects the EQ link group (1–8) to which the EQ of that

channel belongs. EQ parameters are linked for input

channels belonging to the same group.

Note

The input channel EQ link groups are independent from the

output channel EQ link groups.

E LIBRARY

This button accesses the INPUT EQ LIBRARY screen

(➥ p.289), where you can store/recall input channel

EQ library settings.

F ATT (Attenuation)

This knob adjusts the amount of attenuation/gain

immediately following AD conversion in a range of

–96 dB to +24 dB. This is linked with the ATT knob in

the ø/ATT 1-48 screen and ø/ATT STIN/FXRTN

screen. The current value is displayed in the box

located below the knob.

G EQ TYPE

Selects the type of EQ. Turning the TYPE I button on

selects the algorithm used in the 02R series. Turning

the TYPE II button on selects a newly developed algo-

rithm. TYPE II reduces the interference between bands.

H EQ graph

This graph shows the approximate response of the EQ

parameters. The colored vertical lines indicate the

FREQ (center frequency) of the band for the parame-

ter at which the cursor is located. (The color of each

line matches the knob markings for each band.) The

response curve will change when you edit the Q or

GAIN of each band.

I Level meters

These meters indicate the peak levels before EQ and

after EQ. If the signal clips before or after EQ, the

OVER segment will light.

J EQ FLAT

This button resets the GAIN parameters of all bands to

the default value (±0.0 dB). When you click this but-

ton, a confirmation message will appear.

K HPF (High Pass Filter)

The high pass filter located after attenuation and before

EQ can be switched on/off, and you can adjust its cut-

off frequency. The cutoff frequency can be adjusted in

a range of 20–600 Hz.

L Knobs

These knobs adjust the Q, FREQ (center frequency),

and GAIN (amount of boost/cut) for each band.

M (LOW shelving)

If this button is on, the LOW EQ will function as a

shelving-type EQ. The Q knob will disappear.

N (HIGH shelving)

If this button is on, the HIGH EQ will function as a

shelving-type EQ. The Q knob will disappear.

O LPF (Low Pass Filter)

If this button is on, the HIGH EQ will function as a

low-pass filter. The Q knob will disappear, and the

GAIN knob is used to switch the LPF on/off.

EQ PARAM (EQ parameter) screen

EQ PARAM

1 2 3 54

987 6 J

MK NOL

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 287

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

These screens list the EQ settings for the input channels.

Here you can also copy EQ settings between input

channels.

Note

In some screens that include channel numbers as part of the

screen name, changing the Pair Mode to Vertical Pairing in

the MIXER SETUP screen will change the name of the

screen.

Example: EQ 1-24 screen → EQ 1,25- screen

A EQ graph

This mini-graph shows the approximate EQ response

for each input channel.

When you click the graph at which the cursor is cur-

rently located, the EQ PARAM screen for that channel

will appear.

In this screen you can drag and drop the mini-graph

from the desired channel to copy its EQ settings.

(When you drag and drop the mini-graph, a window

will appear, asking you to confirm the copy operation.)

You can also copy EQ settings between the three

screens EQ 1-24, EQ 25-48, and EQ STIN/FXRTN.

First drag the mini-graph over the EQ 1-24, EQ 25-48,

or EQ STIN/FXRTN tabs in the screen (the screen will

switch). Then drag and drop the mini-graph onto the

desired channel, and a window will appear, asking you

to confirm the copy operation.

B EQ ON/OFF

Turns the EQ on/off for that channel. This is linked for

two paired channels.

C Channel

This is the number of the channel you are editing. Two

paired channels are indicated by a heart symbol dis-

played between them.

D Level meter

This meter indicates the peak level after EQ. If the sig-

nal clips, the OVER segment will light.

EQ 1-24 screen

EQ 25-48 switch

EQ STIN/FXRTN screen

EQ 1-24

EQ STIN/FXRTN

4 1 2

INPUT ø/EQ function

288 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

Here you can adjust the amount of attenuation/gain

immediately following AD conversion, and reverse the

phase.

A GANG

When you turn this button on, attenuation/gain set-

tings will be linked for adjacent odd-numbered/even-

numbered channels (or the L/R sides of an STIN/

FXRTN channel).

If the settings are different when you turned the but-

ton on, they will maintain their relative difference

while linked.

B ø (Phase)

This button inverts the phase of each channel’s signal

following AD conversion.

C Attenuation/gain

For each channel, you can adjust the amount of attenu-

ation/gain immediately following AD conversion over

a range of –96 dB to +24 dB. This is linked with the

ATT knob of the EQ PARAM screen. The current value

is displayed in the box located below the knob.

D Channel

This is the number and name of the channel. If two

adjacent odd-numbered/even-numbered channels are

paired (or if a STIN channel or FXRTN channel is dis-

played), a heart symbol is displayed between the two

channels.

ø/ATT 1-48 (Phase/Attenuation

1-48) screen

ø/ATT STIN/FXRTN (Phase/Attenua-

tion STIN/FXRTN) screen

ø /ATT 1-48

ø /ATT STIN/FXRTN

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 289

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

Here you can recall, store, rename, or delete items in the

input EQ library.

Except for the fact that these are EQ settings for the input

channels, display and operations are the same as in the

OUTPUT EQ function OUTPUT EQ LIBRARY screen.

Refer to p.252.

INPUT GATE/COMP function

Here you can edit the gate parameters of the selected input

channel.

A Channel selection

Select the input channel (input channel, ST IN chan-

nel) that you want to edit.

B Name

This is the name of the currently selected input chan-

nel. If the input channel is paired (or if a ST IN channel

is selected), a heart symbol is displayed at the right. For

an input channel, you can click this symbol to enable/

disable pairing.

C GATE ON/OFF

Turns the gate for that channel on/off.

D LIBRARY

This button accesses the GATE LIBRARY screen

(➥ p.294), where you can store/recall gate library set-

tings for input channels.

INPUT EQ LIBRARY screen

INPUT EQ LIBRARY

GATE PARAM (Gate parameter)

screen

GATE PARAM

1 2 3 4

INPUT GATE/COMP function

290 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

E Level meters

These meters indicate the

amount of gain reduction

(GR), the peak level before

(PRE) and after (POST)

the gate, and the peak level

of the key-in signal (KEY

IN) that causes the gate to

operate. If the signal clips,

the OVER segment will

light.

If stereo link is turned on

for the input channel (or if

a ST IN channel is

selected), level meters for

two channels are

displayed.

Hint

If GR METER ON/OFF LINK is turned on in the PREFER-

ENCE 1 screen (UTILITY function), the gain reduction meter

will not be displayed when the gate is off.

F Type

Indicates the type of the currently selected gate.

Hint

To change the gate type, use the INPUT GATE LIBRARY

screen to recall a library item that has a different type. You

cannot change only the gate type in this screen.

G STEREO LINK

This specifies whether parameter settings and gate

operation by a key-in signal will be linked (STEREO

LINK button on) for adjacent odd-numbered/even-

numbered input channels and the L/R channels of ST

IN channels, or not (STEREO LINK button off).

❏ Key-in signal flow when Link= On

❏ Key-in signal flow when Link= Off

Note

Stereo Link is fixed at On for paired channels.

H Gate graph

This graph displays the approximate response of the

gate.

I KEY IN SOURCE

Here you can select one of the following as the key-in

signal that will be used. (If an input channel is selected,

its name will be displayed at the right.)

J FILTER

Select the type of filter to be applied to the selected key-

in signal, from the following types.

• HPF (High Pass Filter)

Passes the portion of the signal above the specified fre-

quency (the cutoff frequency), and cuts the portion

below. If you select this filter, use the knob at the right

to adjust the cutoff frequency (20 Hz–20 kHz).

• BPF (Band Pass Filter)

Passes only the specified frequency region (the band

pass frequency), and cuts the rest of the signal. If you

select this filter, use the knobs at the right to adjust the

band pass frequency (20 Hz–20 kHz) and Q (10.0–

0.10).

• LPF (Low Pass Filter)

Passes the portion of the signal below the specified fre-

quency (the cutoff frequency), and cuts the portion

above. If you select this filter, use the knob at the right

to adjust the cutoff frequency (20 Hz–20 kHz).

THR

LINK= ON

Odd-numbered

channel key-in signal

Even-numbered

channel key-in signal

ATTACK

processing

ATTACK

processing

Detect

maximum

level

SELF PRE EQ

The pre-EQ signal of the currently

selected input channel

SELF POST EQ

The post-EQ signal of the currently

selected input channel

CH 1–48 POST EQ The post-EQ signal of the corre-

sponding input channel (however,

you can only choose channels

belonging to the same group,

within the seven groups CH1–8,

CH9–16, CH17–24, CH25–32,

CH33–40, CH41–48, and ST IN

1L/1R–4L/4R)

ST IN 1L/1R–4L/4R

POST EQ

MIX 21–24

The output signal of the corre-

sponding MIX channel immedi-

ately before the output patch

THR

LINK= OFF

Odd-numbered

channel key-in signal

Even-numbered

channel key-in signal

ATTACK

processing

ATTACK

processing

Detect max-

imum level

Detect max-

imum level

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 291

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

K FILTER ON/OFF

This is an on/off switch for the filter applied to the key-

in signal.

L CUE

This button cue-monitors the currently selected key-in

signal.

Note

Even if the cue mode is set to MIX CUE (which lets you moni-

tor the mix of all channels whose [CUE] key is on), only the

corresponding signal will take priority for monitoring when you

turn on the CUE button in the GATE PARAM screen. (Any

[CUE] keys that had been on at that time will be forcibly turned

off.)

M THRESHOLD (Threshold level)

Specifies the level at which the gate will open and close.

The gate will open when the key-in signal exceeds this

level, and will close when the signal falls below this

level.

N ATTACK (Attack time)

Specifies the time from when the key-in signal exceeds

the threshold level until the gate opens.

O HOLD (Hold time)

Specifies the time that the gate will remain open after

the key-in signal falls below the threshold.

P DECAY (Decay time)

Specifies the time over which the gate will close after

the hold time has elapsed.

Q RANGE

Specifies the amount of attenuation while the gate is

closed.

Here you can edit the compressor parameters of the

selected input channel.

A Channel selection

Select the input channel (input channel, ST IN chan-

nel) that you want to edit.

B Name

This is the name of the currently selected input chan-

nel. If the input channel is paired (or if a ST IN channel

is selected), a heart symbol is displayed at the right. For

an input channel, you can click this symbol to enable/

disable pairing.

C COMP ON/OFF (Compressor on/off)

Turns the compressor on/off for that channel.

D COMP LINK GROUP (Compressor link

group)

Selects the compressor link group (1–8) to which that

channel belongs. Compressor parameters are linked for

input channels belonging to the same group.

Note

Input channel compressor link groups are independent from

output channel compressor link groups.

E LIBRARY

This button accesses the COMP LIBRARY screen

(➥ p.256), where you can store/recall compressor

library settings for input channels.

M N O P Q

COMP PARAM (Compressor parame-

ter) screen

COMP PARAM

1 2 3 54

INPUT GATE/COMP function

292 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

F Level meters

These meters indicate the

amount of gain reduction

(GR), the peak level before

(PRE) and after (POST)

the compressor, and the

peak level of the key-in

signal (KEY IN) that

causes the compressor to

operate. If the signal clips,

the OVER segment will

light.

G Type

Indicates the type of the currently selected compressor.

H STEREO LINK

This specifies whether compressor parameter settings

and key-in signal operation will be linked for adjacent

odd-numbered/even-numbered input channels (STE-

REO LINK button on), or will be independent

(STEREO LINK button off). (For details on compres-

sor stereo link ➥ p.254)

I Compressor graph

This graph displays the approximate response of the

compressor.

J KEY IN SOURCE

Select the desired key-in signal from the following

choices.

K THRESHOLD (Threshold level)

L RATIO

M ATTACK (Attack time)

N RELEASE (Release time)

O GAIN

P KNEE

These parameters are the same as in the OUTPUT

COMP function COMP PARAM screen (➥ p.255).

SELF PRE EQ

The pre-EQ signal of the currently

selected input channel

SELF POST EQ

The post-EQ signal of the currently

selected input channel

CH 1–48 POST EQ The post-EQ signal of the corre-

sponding input channel (however,

you can only choose channels

belonging to the same group,

within the seven groups CH1–8,

CH9–16, CH17–24, CH25–32,

CH33–40, CH41–48, and ST IN

1L/1R–4L/4R)

ST IN 1L/1R–4L/4R

POST EQ

MIX 21–24

The output signal of the corre-

sponding MIX channel immedi-

ately before the output patch

K L M N O P

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 293

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

These screens list the gate/compressor settings for the input

channels. Here you can also copy gate/compressor settings

between input channels.

A Gate graph

This mini-graph shows the approximate gate response

for each input channel. If you click the mini-graph, the

GATE PARAM screen for that channel will appear.

B Level meters

These meters show the amount of gain reduction pro-

duced by the gate (at left), and the peak level of the

signal after passing through the gate (at right). If the

signal clips, the OVER segment will light.

C GATE ON/OFF

Turns the gate for that channel on/off.

D Compressor graph

This mini-graph shows the approximate compressor

response for each input channel. If you click the mini-

graph, the COMP PARAM screen for that channel will

appear.

E Level meters

These meters show the amount of gain reduction pro-

duced by the compressor (at left), and the peak level of

the signal after passing through the compressor (at

right). If the signal clips, the OVER segment will light.

F COMP ON/OFF (Compressor on/off)

Turns the compressor on/off for that channel.

G Channel

This area shows the number and name of the channel

you are editing. Two paired channels are indicated by a

heart symbol displayed between them.

In this screen, you can copy gate/compressor settings

by dragging and dropping the mini-graph of a desired

channel onto another channel. You can also copy gate/

compressor settings between different screens (for the

procedure ➥ p.255).

CH 1-12 (Input channel 1–12) screen

CH 13-24 (Input channel 13–24)

screen

CH 25-36 (Input channel 25–36)

screen

CH 37-48 (Input channel 37–48)

screen

ST IN (ST IN channel) screen

CH 1-12

ST IN

2 1 4

INPUT GATE/COMP function

294 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

Here you can recall, store, rename, or delete items in the

gate library.

A EDIT

When you click this button, the GATE PARAM screen

for the currently selected input channel will appear.

B Channel selection

Select the input channel that you want to edit. The

name of the channel is displayed at the right.

C Gate graph of the selected channel

This graph shows the approximate response of the gate

for the currently selected channel.

D Level meters

These meters show the amount of gain reduction (GR),

and the peak levels before the gate (PRE) and after the

gate (POST). If the signal clips, the OVER segment will

light.

E RECALL

Recalls the gate library item selected in the list into

memory.

F STORE

Stores the gate settings of the currently selected chan-

nel into the location selected in the list. When you click

this button a window will appear, allowing you to

name and save the settings.

G TITLE EDIT

Edits the title of the library item selected in the list.

When you click this button a window will appear,

allowing you to edit the title.

H CLEAR

Deletes the library item selected in the list. When you

click this button, a confirmation message will appear.

Note

Library items with an “R” displayed in the right column of the

list are read-only. Read-only items cannot be stored,

renamed, or deleted.

I Library gate graph

This graph indicates the approximate response of the

gate library item selected in the list.

J Library list

Use the scroll bar to select the library item on which

you want to perform an operation. The selected library

item will move to the center, and will be highlighted.

GATE LIBRARY screen

GATE LIBRARY

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 295

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

Here you can recall, store, rename, or delete items in the

compressor library.

Except for the fact that these settings are for input chan-

nels, this is the same as the OUTPUT COMP function

COMP LIBRARY screen. Refer to p.256.

INPUT DELAY function

Here you can edit the delay parameters of the selected

input channel.

A DELAY SCALE

Here you can select the units in which the delay time is

displayed. The units that can be selected are the same

as in OUTPUT DELAY function DELAY SCALE

(➥ p.257). When you change the delay scale in the

INPUT DELAY function, the delay scale of the OUT-

PUT DELAY function will also change accordingly.

COMP LIBRARY (Compressor library)

screen

COMP LIBRARY

CH 1-24 (Input channel 1–24) screen

CH 25-48 (Input channel 25–48)

screen

ST IN (ST IN channel) screen

CH 1-24

ST IN

INPUT DCA/GROUP function

296 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

B GANG

C Delay time knob

D DELAY ON/OFF

These are the same as in the OUTPUT DELAY func-

tion (➥ p.258).

E Channel

This area shows the number and name of the input

channel you are editing. Two paired channels (or a ST

IN channel) are indicated by a heart symbol displayed

between them. You can click this symbol to enable/dis-

able pairing.

INPUT DCA/GROUP function

Here you can specify the input channels that will be

assigned to DCA groups 1–8. The level of input channels

belonging to the same DCA group can be adjusted as a

whole using DCA faders 1–8.

A DCA group

This is the number of the DCA group. The number

corresponding to the grid where the cursor is located is

highlighted.

B Name

This is the name of the DCA group. You can also click

this area to edit the name.

C Grid

This grid lets you assign input channels (horizontal

rows) to DCA groups (vertical columns). Currently-

patched grids are indicated by a symbol. Move the

cursor to the desired grid and press the [ENTER] key

(or click) to set/disable the assignment.

Hint

You can also assign a single input channel to multiple DCA

groups for multiple DCA control.

Hint

DCA groups 1–6 are for input channels only, but DCA groups

7/8 can be used with both input channels and output chan-

nels. Both types of channel can exist in an identically-

numbered group.

DCA GROUP ASSIGN screen

DCA GROUP ASSIGN

21 3

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 297

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

D SET BY CUE (Assign by [CUE] key)

This specifies whether the [CUE] key will be used to

make/cancel DCA group assignments. While the DCA

group SET BY CUE button is on, pressing the [CUE]

key of an input channel that can be assigned to the cor-

responding group will assign the channel to the group.

(Press the [CUE] key once again to cancel the

assignment.)

Hint

The SET BY CUE button can be turned on for only one DCA

group. This is automatically turned off when you change

screens or turn off the power.

E CLEAR

This button clears all input channels assigned to that

DCA group.

F MUTE

These buttons switch muting on/off for DCA groups

1–8. They are linked with DCA [MUTE] keys 1–8 in

the DCA strip of the panel.

G DCA faders

These faders adjust the levels of DCA groups 1–8. They

are linked with DCA faders 1–8 in the DCA strip.

H CUE

These buttons cue-monitor DCA groups 1–8. They are

linked with DCA [CUE] keys 1–8 in the DCA strip of

the panel.

I DCA LEVEL SET

Use the following two buttons to operate DCA groups

1–8 together.

• ALL NOMINAL

Clicking this button will move DCA faders 1–8 to

nominal level (0 dB).

• ALL MINIMUM

Clicking this button will move DCA faders 1–8 to the

–∞ dB position.

Here you can specify the input channels that will be

assigned to mute groups 1–8. Muting can be switched on/

off together for channels assigned to the same mute group.

Except for the fact that these settings apply to input chan-

nels, the display and operations are the same as in the

OUTPUT DCA/GROUP function MUTE GROUP

ASSIGN screen. Refer to p.259.

Hint

Mute groups 1–8 can be used with both input channels and

output channels. Both types of channel can exist in the identi-

cally-numbered mute group.

MUTE GROUP ASSIGN screen

MUTE GROUP ASSIGN

INPUT DCA/GROUP function

298 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

Here you can specify the input channels that will be

assigned to EQ link groups 1–8. EQ parameters are linked

for channels belonging to the same group.

A EQ link group

These are the EQ link group numbers. The number

corresponding to the grid where the cursor is located is

highlighted.

B Grid

This grid lets you assign input channels (horizontal

rows) to EQ link groups (vertical columns). Currently-

patched grids are indicated by a symbol. Move the

cursor to the desired grid and press the [ENTER] key

(or click) to set/disable the assignment.

Hint

Input channels and output channels use separate EQ link

groups. Input channels use groups A–H, and output channels

use groups 1–8.

C SET BY CUE (Assign by [CUE] key)

This specifies whether the [CUE] key will be used to

make/cancel EQ link group assignments. While the EQ

link group SET BY CUE button is on, pressing the

[CUE] key of a channel that can be assigned to the cor-

responding group will assign the channel to the group.

(Press the [CUE] key once again to cancel the

assignment.)

Hint

The SET BY CUE button can be turned on for only one EQ

link group. This is automatically turned off when you change

screens or turn off the power.

D CLEAR

This button clears all input channels assigned to that

EQ link group.

EQ LINK ASSIGN screen

EQ LINK ASSIGN

1 2

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 299

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

Here you can specify the input channels that will be

assigned to compressor link groups 1–8. Compressor

parameters are linked for channels belonging to the same

group.

Except for the fact that these settings apply to input chan-

nels, the display and operations are the same as in the

OUTPUT DCA/GROUP function COMP LINK ASSIGN

screen. Refer to p.261.

Hint

Input channels and output channels use separate compres-

sor link groups. Input channels use groups A–H, and output

channels use groups 1–8.

PAN/ROUTING function

Here you can send signals from input channels to the

desired MIX bus. In this screen you can also switch the

type (VARI or FIXED) of each MIX bus, and specify the

location from which the signal will be sent.

A Type selection

Here you can select the mix bus type for every two

adjacent odd-numbered/even-numbered MIX buses.

You can choose one of the following types.

• FIXED

The send level of the MIX bus is fixed at nominal level

(0.0 dB). Choose this if you want to use the MIX bus as

a group output or as a bus output for recording on a

multitrack recorder.

• VARI (Variable)

The send level of the MIX bus is adjustable. Choose

this if you want to use the MIX bus as an external effect

send or as a foldback output.

Hint

If surround mode is enabled, the type indication will change to

“SURROUND” for MIX buses used as surround buses. You

cannot change the mix bus type during this time.

B MIX bus

This is the number and name of the MIX bus to which

the signal is sent. Paired MIX buses are indicated by a

heart symbol displayed between them. You can click

this symbol to enable/disable pairing.

C POST ON/POST TO ST (Post on / Post to

stereo)

This button lets you specify in greater detail the loca-

tion from which post-fader signals will be sent from

input channels to this MIX bus. You can choose one of

the following two send locations.

COMP LINK ASSIGN (Compressor link

assign) screen

COMP LINK ASSIGN

CH to MIX (Channel to mix) screen

CH to MIX

1 2

PAN/ROUTING function

300 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

❏ POST ON

The signal will be sent from immediately after the

[ON] key.

POST ON/POST TO ST=

❏ POST TO ST

The signal will be sent from immediately after the [TO

STEREO] key.

POST ON/POST TO ST=

Hint

This setting applies to the signals sent from all input channels

to the corresponding MIX bus.

D CH to MIX (Channel to mix)

In this area, the signals sent from input channels / ST

IN channels (vertical columns) to MIX buses (horizon-

tal rows) can be switched on/off and their level

adjusted.

The buttons and knobs displayed here will differ

depending on the type (FIXED or VARI) of the send-

destination MIX bus, and on whether the MIX buses

are paired.

❏ Type = FIXED, Pairing = disabled

MIX1

MIX2

STEREO L

STEREO R

……

FADER

INPUT CHANNEL 1

ON TO ST

PAN

MIX1 (VARI)

LEVEL

MIX2 (VARI)

LEVEL

MIX1

MIX2

STEREO L

STEREO R

……

FADER

INPUT CHANNEL 1

ON TO ST

PAN

MIX1 (VARI)

LEVEL

MIX2 (VARI)

LEVEL

Input channel 1

↓

MIX bus 1

Input channel 1

↓

MIX bus 2

Input channel 2

↓

MIX bus 1

Input channel 2

↓

MIX bus 2

SEND ON/OFF button

On/off switch for the signal sent from

input channels to each MIX bus.

MIX1

MIX2

STEREO L

STEREO R

……

FADER

INPUT CHANNEL 1

PAN

MIX1 (FIX)

MIX2 (FIX)

FADER

INPUT CHANNEL 2

PAN

MIX1 (FIX)

MIX2 (FIX)

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 301

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

❏ Type = FIXED, Pairing = enabled ❏ Type = VARI, Pairing = disabled

Input channel 1

↓

MIX buses 1/2

Input channel 2

↓

MIX buses 1/2

SEND ON/OFF button

On/off switch for the signal sent from

input channels to the two MIX buses.

MIX1

MIX2

STEREO L

STEREO R

……

FADER

INPUT CHANNEL 1

PAN

MIX1/2 (FIX)

FADER

INPUT CHANNEL 2

PAN

MIX1/2 (FIX)

SEND ON/OFF button

On/off switch for the signal sent from input

channels to each MIX bus.

PRE/POST button

Selects either PRE (pre-EQ or pre-fader) or

POST (post ON or post TO ST) as the loca-

tion from which the signal will be sent from

input channels to each MIX bus.

SEND LEVEL knob

Adjusts the level of the signal sent from

input channels to each MIX bus.

Input channel 1

↓

MIX bus 1

Input channel 1

↓

MIX bus 2

Input channel 2

↓

MIX bus 1

Input channel 2

↓

MIX bus 2

MIX1

MIX2

STEREO L

STEREO R

……

PAN

MIX1 (VARI)

LEVEL

MIX2 (VARI)

LEVEL

MIX1

MIX2

STEREO L

STEREO R

……

FADER

PAN

MIX1 (VARI)

LEVEL

MIX2 (VARI)

LEVEL

FADER

INPUT CHANNEL 1

• PRE/POST button= PRE

• PRE/POST button= POST

PAN/ROUTING function

302 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

❏ Type = VARI, Pairing = enabled

E PRE EQ/PRE FADER

These buttons let you specify in greater detail the loca-

tion from which the pre-fader signal will be sent from

an input channel to the MIX buses. You can choose

one of the following two send locations.

Hint

This setting applies to the signal sent from the corresponding

input channel to all MIX buses.

F FOLLOW PAN

These buttons specify how the TO ST PAN knob (8)

will affect the signal sent from the input channel to

MIX buses.

• VARI

If this button is on, the PAN knob displayed in the CH

to MIX area (

4) will be linked with the TO ST PAN

knob (

8) if VARI-type MIX buses are paired.

• FIXED

If this button is on, the signal from after the TO ST

PAN (

8) knob will be sent to FIXED-type MIX buses.

G TO ST (To stereo)

This button specifies whether the input channel / ST

IN channel will send its signal to the STEREO bus. This

is linked with the [TO STEREO] switch in the

SELECTED CHANNEL section.

H TO ST PAN (To stereo pan)

Here you can adjust the panning of the signal sent from

the input channel / ST IN channel to the STEREO bus.

(The current value is shown in the boxes immediately

below.) This is linked with the encoder if PAN is

selected as the encoder mode, and with the [PAN]

encoder of the SELECTED CHANNEL section.

I PAN MODE

Here you can select one of the following ways in which

pan settings will be linked between adjacent odd-num-

bered/even-numbered input channels (or the left/right

channels of a ST IN channel).

• INDIVIDUAL

The two pan settings will be independent.

• GANG PAN

The two pan settings will be linked in the same direc-

tion. If the two pan values are different when you turn

on this button, pan will be linked while preserving the

existing difference in values.

• INV. GANG (Inverted gang)

The two pan settings will operate in opposite

directions.

Input channel 1

↓

MIX buses 1/2

Input channel 2

↓

MIX buses 1/2

SEND ON/OFF

button

On/off switch for

the signal sent

from input chan-

nels to the two

MIX buses.

PRE/POST button

Selects either PRE (pre-EQ or pre-fader) or POST

(post ON or post TO ST) as the location from which the

signal will be sent from input channels to each MIX bus.

MIX PAN/BALANCE knob

Speciﬁes the panning of the signal sent

from input channels to the two MIX

buses. If the PAN MODE (

9) of the

input channel is set to BALANCE, this

functions as a BALANCE knob that

adjusts the volume balance between

the two channels.

SEND LEVEL knob

Adjusts the level of the signal

sent from input channels to the

two MIX buses.

MIX1

MIX2

STEREO L

STEREO R

……

MIX1

MIX2

STEREO L

STEREO R

……

INPUT CHANNEL 1

FADER

INPUT CHANNEL 1

PAN

MIX1/2 (VARI)

LEVEL

FADER

PAN

MIX1/2 (VARI)

LEVEL

• PRE/POST button= PRE

• PRE/POST button= POST

PRE FADER Immediately before the fader

PRE EQ Immediately before the EQ

J7 K

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 303

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

• BALANCE

The two PAN knobs will function as BALANCE knobs

that adjust the balance of the signal sent from the odd-

numbered/even-numbered channels (or the L/R chan-

nels of the ST IN channel) to the STEREO bus L/R. If

you choose this setting, the two knobs will be reset to

the center position, and will be linked in the same

direction. Also, the knob markings will change from

red to white.

Note

• Pan mode is always valid, even if the send-source input

channels are not paired.

• You will be unable to operate the TO ST PAN knobs if you

select GANG PAN mode when the two pan knobs are set to

far left and right, or if you select INV.GANG when both pan

knobs are turned all the way in the same direction.

J MIX MINUS

This function sends the same mix as the STEREO bus

— but with a specific input channel removed — to the

desired MIX bus. If you need to send a monitor mix to

a performer or announcer, this is a quick way to give

them the same mix as the STEREO bus but without

their own voice.

Access the desired source input channel in the screen,

and click the MIX MINUS button for that channel; a

window will appear, allowing you to select the MIX bus

for which to make Mix Minus settings.

Hint

As a shortcut to access the above window, you can simulta-

neously press the [SEL] key of the INPUT/ST IN channel strip

and the [SEL] key of the MIX section. However, be aware that

holding down either one of these keys by itself will access a

different shortcut.

In the above window, select the send-destination MIX

bus and click the OK button; the following parameters

will change in the CH to MIX screen.

• In the CH to MIX area of the send-destination MIX

bus, all ON/OFF buttons will turn on.

• In the CH to MIX area of the send-destination MIX

bus, all PRE/POST buttons will be set to POST.

• The send level of signals sent from the source input

channel to the destination MIX bus will be lowered

to –∞ dB.

• The send level of signals sent from all input chan-

nels other than the above to the destination MIX

bus will be set to nominal level (0.0 dB).

• The POST ON/POST TO ST button will be set to

POST TO ST for the destination MIX bus.

Note

• Mix Minus does not switch a “mode”; rather, it is a quick way

to make certain settings. This means that even after execut-

ing Mix Minus, you can freely edit the parameters of the CH

to MIX screen.

• When you execute the Mix Minus operation, only the input

channel you selected as the source will be removed from the

mix. If you want to remove more than one input channel

from the signal sent to a specific MIX bus, execute the Mix

Minus operation and then manually change the settings of

other channels.

• If the input channel is paired (or if a ST IN channel is

selected), the send level of the signal sent from both chan-

nels to the target MIX bus will be set to –∞.

• The Mix Minus operation is valid even if the destination MIX

bus is paired. In this case, the PAN setting of the input chan-

nel will be reflected by the PAN settings of the paired MIX

buses.

K Input channel

This is the source input channel (or channels). Paired

input channels (or a ST IN channel) are indicated by a

heart symbol displayed between them. For an input

channel, you can click this symbol to enable/disable

pairing.

You can move the cursor to a parameter in the CH to

COPY area, and then hold down the [SHIFT] key and

click (or press the [SHIFT] key + [ENTER] key) to

copy the value of that parameter to another channel (in

the horizontal direction) or to another MIX bus (in the

vertical direction), or to switch all parameters on/off.

You can use this method to set the following

parameters.

• Mix send on/off

Move the cursor to the SEND ON/OFF button of the

CH to COPY area; then hold down the [SHIFT] key

and click (or press the [SHIFT] key + [ENTER] key) to

access the following window.

To set multiple parameters at once, use the [DATA]

encoder to select one of the following items, and click

the OK button.

ALL OFF [ALL MIX ]

ALL ON [ALL MIX ]

Switch the signals sent from the selected input chan-

nel to all MIX buses on or off together.

PAN/ROUTING function

304 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

ALL OFF [ALL CH ]

ALL ON [ALL CH ]

Switch the signals sent from all input channels to the

selected MIX bus on or off together.

ALL OFF [ALL CH x ALL MIX]

ALL ON [ALL CH x ALL MIX]

Switch the signals sent from all input channels to all

MIX buses on or off together.

• Mix send position

Move the cursor to a PRE/POST button in the CH to

COPY area; then hold down the [SHIFT] key and click

(or press the [SHIFT] key + [ENTER] key) to access

the following window.

To set multiple parameters at once, use the [DATA]

encoder to select one of the following items, and click

the OK button.

ALL POST [ALL MIX ]

ALL PRE [ALL MIX ]

Switch the send position of the signal sent from the

selected input channel to all MIX buses to either post-

fader or pre-fader.

ALL POST [ALL CH ]

ALL PRE [ALL CH ]

Switch the send position of the signal sent from all

input channels to the selected MIX bus to either post-

fader or pre-fader.

ALL POST [ALL CH x ALL MIX]

ALL PRE [ALL CH x ALL MIX]

Switch the send position of the signal sent from all

input channels to all MIX buses to either post-fader

or pre-fader.

Note

These “all-at-once” operations are ignored by FIXED-type MIX

buses.

• Mix send level

Move the cursor to a SEND LEVEL knob in the CH to

COPY area; then hold down the [SHIFT] key and click

(or press the [SHIFT] key + [ENTER] key) to access

the following window.

To set multiple parameters at once, use the [DATA]

encoder to select one of the following items, and click

the OK button.

LEVEL COPY [ALL MIX ]

The value of the selected SEND LEVEL knob will be

copied to the send level of the signals sent from that

input channel to all MIX buses.

LEVEL COPY [ALL MIX ]

The value of the selected SEND LEVEL knob will be

copied to the send level of the signals sent from all

input channels to that MIX bus.

LEVEL COPY [ALL CH x ALL MIX]

The value of the selected SEND LEVEL knob will be

copied to the send level of the signals sent from all

input channels to all MIX buses.

Note

These “all-at-once” operations are ignored by FIXED-type MIX

buses.

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 305

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

• Mix pan/balance

When the destination MIX bus is paired, move the cur-

sor to a MIX PAN/BALANCE knob displayed in the

CH to COPY area; then hold down the [SHIFT] key

and click (or press the [SHIFT] key + [ENTER] key) to

access the following window.

To set multiple parameters at once, use the [DATA]

encoder to select one of the following items, and click

the OK button.

PAN (BAL) COPY [ALL MIX ]

The value of the selected MIX PAN/BALANCE knob

will be copied to the pan (balance) of signals sent

from that channel to all paired MIX buses.

PAN (BAL) COPY [ALL MIX ]

The value of the selected MIX PAN/BALANCE knob

will be copied to the pan (balance) of signals sent

from all channels to that MIX bus.

PAN (BAL) COPY [ALL CH x ALL MIX]

The value of the selected parameter will be copied to

the pan (balance) of signals sent from all channels to

all paired MIX buses.

Note

• This operation is ignored by unpaired MIX buses and

FIXED-type MIX buses.

• You cannot copy PAN parameters to BALANCE parameters

(or vice versa).

• Copying is invalid for channels whose VARI button (in the

FOLLOW PAN area) is on.

This screen lists the signals sent from the input channels to

the MIX buses. You can also edit the settings from within

this screen.

A CH to MIX/MIX from CH

Select one of the following two types of screen display.

❏ When the CH to MIX button is on

The screen shows the status of the signals sent from a

specific input channel (input channel / ST IN channel)

to all MIX buses. (Use the scroll bar to see input chan-

nels that are not currently shown.)

❏ When the MIX from CH button is on

The screen shows the status of the signals sent from all

input channels to a specific MIX bus.

MIX SEND VIEW screen

MIX SEND VIEW

1 2

PAN/ROUTING function

306 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

B SEND LEVEL, PRE/POST (Send level / Send

point)

Select one of the following two parameters to view in

the grid.

❏ When the SEND LEVEL button is on

The send levels of the signals sent from input channels

to MIX buses are shown in the grid as bar graphs.

Except for the fact that the send-sources are input

channels and the send-destinations are MIX buses, the

bar graph display is the same as in the MIX to

MATRIX VIEW screen (MATRIX/ST function)

(➥ p.264).

Depending on the send location of the signal being sent

to the MIX bus, the color of the bar graph will differ as

follows.

(green) . . . . PRE EQ (immediately before

the EQ)

(yellow) . . . PRE FADER (immediately

before the fader)

(blue) . . . . . POST ON (immediately after

the [ON] key) or POST TO ST

(immediately after the [TO ST]

key)

To edit the send level of a signal, move the cursor to

the grid where the desired channel and MIX bus inter-

sect, and turn the [DATA] encoder. To switch a MIX

send on/off, click the grid where the desired channel

and MIX bus intersect.

If the SEND LEVEL button is on, you can select a

desired grid and copy its send level (pan) value to other

channels (horizontal direction) or to other MIX buses

(vertical direction), or switch all grids on/off

simultaneously.

To do so, move the cursor to the desired grid; then

hold down the [SHIFT] key and press the [ENTER]

key. (Alternatively, hold down the [SHIFT] key and

click the desired grid.) When the following window

appears, select one of the following choices to copy,

and click the OK button.

LEVEL COPY [ALL MIX ]

Copy the send level (pan) value of the selected grid to

all MIX buses.

LEVEL COPY [ALL CH ]

Copy the send level (pan) value of the selected grid to

all input channels.

LEVEL COPY [ALL CH x ALL MIX]

Copy the send level (pan) value of the selected grid to

all input channels / all MIX buses.

ALL OFF [ALL MIX ]

Turn off the signals sent from the specified input

channel to all MIX buses.

ALL ON [ALL MIX ]

Turn on the signals sent from the specified input

channel to all MIX buses.

ALL OFF [ALL CH ]

Turn off the signals sent from all input channels to

the specified MIX bus.

ALL ON [ALL CH ]

Turn on the signals sent from all input channels to

the specified MIX bus.

ALL OFF [ALL CH x ALL MIX]

Turn off the signals sent from all input channels to all

MIX buses.

ALL ON [ALL CH x ALL MIX]

Turn on the signals sent from all input channels to all

MIX buses.

❏ When the PRE/POST button is on

This screen shows the send positions of the signals sent

from the input channels to the MIX buses.

Each indication has the following significance.

(green) . . . PRE EQ (immediately before

the EQ)

(yellow) . . PRE FADER (immediately

before the fader)

(gray) . . . . POST ON (immediately after

the [ON] key)

(red) . . . . . POST TO ST (immediately after

the [TO ST] key)

To change the send position of a signal, move the cur-

sor to the grid where the desired channel and MIX bus

intersect, and press the [ENTER] key, or click, or turn

the [DATA] encoder.

If the PRE/POST button is on, the send position for all

grid locations can be changed simultaneously. To do

so, hold down the [SHIFT] key and click the desired

grid. (Alternatively, move the cursor to the desired

grid; then hold down the [SHIFT] key and press the

[ENTER] key.) When the following window appears,

select one of the following choices and click the OK

button.

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 307

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

ALL PRE [ALL MIX ]

Specify pre-fader as the send position for signals sent

from the specified input channel to all MIX buses.

ALL POST [ALL MIX ]

Specify post-fader as the send position for signals sent

from the specified input channel to all MIX buses.

ALL PRE [ALL CH ]

Specify pre-fader as the send position for signals sent

from all input channels to the specified MIX bus.

ALL POST [ALL CH ]

Specify post-fader as the send position for signals sent

from all input channels to the specified MIX bus.

ALL PRE [ALL CH x ALL MIX]

Specify pre-fader as the send position for signals sent

from all input channels to all MIX buses.

ALL POST [ALL CH x ALL MIX]

Specify post-fader as the send position for signals sent

from all input channels to all MIX buses.

C Grid

This area shows various settings for the signals sent

from the input channels (horizontal rows) to the MIX

buses (vertical columns). The red lines extending

toward the left and upward indicate the corresponding

input channel and MIX bus for the grid at which the

cursor is now located.

D SELECTED PARAMETER (currently selected

parameter)

This indicates the input channel and MIX bus for the

grid where the cursor is currently located. The four

boxes at right indicate the values for the grid where the

cursor is currently located.

This screen lists the signals sent from the input channels to

the buses and direct outputs. You can also set or cancel

these assignments from within this screen.

A Input channel

This area indicates the number and name of the input

channel you are editing.

B PAN

If this button is on, the input channel’s TO STEREO

PAN knob setting will also apply to the signal sent to

FIXED-type MIX buses. This is linked with the FOL-

LOW PAN FIXED button of the CH to MIX screen

(PAN/ROUTING function).

C Bus assignments

These buttons assign the corresponding input channel

to FIXED-type MIX buses. These are linked with the

SEND ON/OFF buttons of the CH to MIX screen

(PAN/ROUTING function). For VARI-type MIX

buses, the buttons are grayed-out and inoperable.

Note

If a surround mode other than STEREO is selected, the but-

tons for MIX buses used as surround buses will be named by

their surround channel (e.g., L, C, R) rather than by number.

FIX ASSIGN VIEW screen

FIX ASSIGN VIEW

PAN/ROUTING function

308 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

D TO ST (To stereo)

If this button is on, the corresponding input channel is

assigned to the STEREO bus. This is linked with the

TO ST button of the CH to MIX screen (PAN/ROUT-

ING function).

E DIRECT

If this button is on, the signal of the corresponding

input channel will be sent to the output port selected as

the direct output. This is linked with the DIRECT OUT

ON/OFF button in the INSERT/DIRECT OUT POINT

screen (IN PATCH function).

F Output port

This area indicates the output port that is patched in

the DIRECT OUT PATCH screen (INPUT PATCH

function) to the direct output of this input channel

G ALL STEREO

Clicking this button enables the assignment of all input

channels to the STEREO bus.

H ALL BUS

Clicking this button enables the assignment of all input

channels to FIXED-type MIX buses.

I ALL CLEAR

Clicking this button cancels all assignments in the FIX

ASSIGN VIEW screen.

J SURROUND MODE

This indicates the currently selected surround mode.

Here you can make settings for LCR mode, which allows

three-channel playback by adding a CENTER channel to

the L/R channels of the STEREO bus.

Except for the fact that the send-sources are input chan-

nels, the display and operations are the same as in the

MATRIX/ST function LCR screen. Refer to p.267.

8 9

LCR screen

LCR

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 309

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

Here you can perform realtime control of surround pan-

ning for the two currently selected input channels.

A Channel selection

Select the two adjacent odd-numbered/even-num-

bered input channels (or ST IN channel L/R) that you

want to control. The names of these channels are dis-

played at the right.

B DIVERGENCE

These controls specify the proportion at which the sig-

nals are sent to each surround bus when the input

channel is positioned in the center. Depending on the

currently selected surround mode, the displayed

parameters will differ as follows.

❏ If Surround Mode = 3-1ch/5.1ch

A knob for controlling the front

divergence is displayed. Use this

knob to specify the proportion (0–

100) at which a signal positioned

in the center will be sent to the

center bus (C) and the left/right

buses (L, R). With a setting of 0

the signal will be sent only to the

left/right buses, and with a setting

of 100 it will be sent only to the center bus. With a set-

ting of 50, the signal will be sent at the same level to the

left/right and center buses.

❏ If Surround Mode = 6.1ch

An F knob for controlling the front divergence and an

R knob for controlling the rear divergence are dis-

played. Use these two knobs to specify the proportion

(0–100) at which a signal positioned in the center will

be sent to the center buses (C, S, Bs) and the left/right

buses (L, R, Ls, Rs).

In 6.1ch mode, a LINK button

that links the front and rear diver-

gence is displayed between the F

knob and R knob. When you turn

the LINK button on, the F knob

value will be copied to the R knob,

and the F knob and R knob values

will be linked.

C LFE (Low Frequency Effect)

This adjusts the output level of the signal sent from the

input channel to the LFE (Low Frequency Effect) bus

for a subwoofer. You can use the ON/OFF button to

switch the signal sent from the input channel to the

LFE bus on/off.

The LFE knob and ON/OFF button are displayed only

when the surround mode is 5.1ch or 6.1ch.

D Surround pan grid

This grid lets you control the surround panning, with

the listening point at the center. The current setting is

indicated by a O symbol.

E Position buttons

These buttons correspond to each surround bus. When

you click a button, the surround panning will move to

that position.

F SURROUND BUS ON/OFF buttons

These buttons are on/off switches for the signal sent

from the input channel to the corresponding surround

bus.

G Surround pan position

This indicates the coordinate locations of the O sym-

bol in the left/right direction and the front/rear

direction.

SURR PARAM (Surround parameter)

screen

SURR PARAM

5 6 7

PAN/ROUTING function

310 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

H STEREO LINK

This specifies whether sound image movement will be

linked between the two channels shown in the screen.

To link the movement of the two channels, use the /

buttons at left and right to select one of the eight link

patterns. (For details on how each pattern will operate,

refer to p.146)

I SURROUND MODE

This indicates the currently selected surround mode.

J Level meters

These meters show the master levels of the surround

buses.

K MIX SEND ASSIGNMENT

If MIX SEND is selected as the operation of the MIX

section, this area indicates the surround parameters

that can be operated by the MIX [ON] key and MIX

encoder of the corresponding surround bus.

This screen shows the surround settings for each input

channel. From this screen you can also jump to the SURR

PARAM screen for the desired channel.

A Surround pan grid

For each input channel, the approximate surround pan

position is shown by the O symbol. If you click this

area, the SURR PARAM screen for that channel will

appear.

B Surround pan position

This indicates the surround pan coordinate positions

in the left/right direction (L/R) and the front/rear

direction (F/R).

C Channel

This is the number and name of the input channel.

8 9 J

SURR VIEW (Surround view) screen

SURR VIEW

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 311

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

For two adjacent odd-numbered/even-numbered input

channels (or ST IN channel L/R), these settings convert the

two-channel signal from an MS mic into L/R signals.

A S-GAIN knob

This knob sets the proportionate level of the S mic rela-

tive to the level of the M mic. The current value is

shown in the numerical box at the right.

At the MONO position, the S mic level will be at –∞, at

the STEREO position the M mic and S mic will be at

the same level, and at the EXP.ST position the S mic

level will be +10 dB.

B M/S DECODE ON/OFF

This button switches M/S decoding on/off for two

adjacent odd-numbered/even-numbered input chan-

nels (or ST IN channel L/R). M/S decoding can be

switched on even for channels that are not assigned as a

stereo pair.

C Channel

This is the number and name of the input channel.

Hint

M/S is a stereo recording technique in which two micro-

phones are used; a uni-directional M (Middle) mic and a bi-

directional S (Side) mic. The M mic captures the main signal

and the S mic captures the directional signal, and the sum

(M+S) and difference (M-S) of the two signals (this procedure

is known as “decoding”) is recorded on the L and R channels

respectively.

INPUT VIEW function

This screen lists the mix parameters of the currently

selected input channel. In this screen you can also edit the

principal parameters and access other screens.

A Channel

This is the number of the input channel you are edit-

ing. If the input channel is paired (or if a ST IN channel

is selected), a heart symbol is displayed at the right.

You can click this symbol to enable/disable pairing for

the input channel.

B HA (Head Amp)

This area indicates the input port that is patched to the

input channel, the setting of the internal head amp

(PM5D-RH model only) or external head amp, and the

input level. In this screen you can also adjust the head

amp gain and switch phantom power (+48V) on/off.

C ATT (Attenuation)

This area shows the attenuation and ø (phase) settings.

You can also adjust the attenuation and switch the

phase from this screen.

M/S screen

M/S

CH VIEW (Channel view) screen

CH VIEW

INPUT VIEW function

312 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

D EQ

Refer to the explanation of the OUTPUT VIEW func-

tion CH VIEW screen (➥ p.270).

E GATE

This area shows the amount of gain reduction and the

output level of the gate, a mini-graph showing the

approximate response of the gate, and the gate on/off

status. You can also switch the gate on/off from this

screen. If you click the mini-graph, the GATE PARAM

screen for that channel will appear.

F COMP (Compressor)

Refer to the explanation of the OUTPUT VIEW func-

tion CH VIEW screen (➥ p.270).

G DELAY

In this area you can view and edit the delay time of the

internal delay and its on/off status.

H TO MIX

In this area you can specify the send level, output posi-

tion, and on/off status of the signals sent from the

corresponding input channel to MIX buses 1–24.

(Operation is the same as in the TO MATRIX area of

the OUTPUT VIEW function CH VIEW screen.) Refer

to p.270.

I TO STEREO

Here you can specify the on/off status, pan, and FOL-

LOW PAN settings of the signal sent from the

corresponding input channel to the STEREO bus.

J DCA group / Mute group

K Recall safe / Mute safe

Refer to the explanation of the OUTPUT VIEW func-

tion CH VIEW screen (➥ p.271).

L DIRECT

Turns direct output on/off for the corresponding input

channel.

M INSERT

Turns insert on/off for the corresponding input

channel.

N SURROUND (Surround pan)

If surround mode is enabled, the surround pan posi-

tion of the corresponding input channel is indicated by

the O symbol in the surround pan grid and also as a

front/rear/left/right coordinate position. If you click

the surround pan grid, the SURR PARAM screen for

that channel will appear.

O LCR

Here you can switch LCR mode on/off, and adjust CSR

(the level of the CENTER channel relative to the L/R

channels) (➥ p.267).

P LIBRARY

This button accesses the INPUT CH LIBRARY screen

(➥ p.316), where you can store/recall input channel

library settings.

Q Level meter

This level meter indicates the input level of the channel.

R Signal detection point

This is the point at which the signal level shown in the

level meter (

Q) is detected (PRE ATT, PRE GATE,

PRE FADER, POST FADER, or POST ON). You can

edit this setting by clicking the / buttons at the left

and right.

S Fader

This controls the input level of the channel.

T CUE

U ON/OFF (Channel on/off)

Refer to the explanation of the OUTPUT VIEW func-

tion CH VIEW screen (➥ p.271).

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 313

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

This screen shows the signal flow for two adjacent odd-

numbered/even-numbered input channels or ST IN chan-

nels. In this screen you can also edit some of the

parameters, and access other screens. You can also deter-

mine the location within the signal flow at which clipping

occurred.

A Channel

B Insert

Except for the fact that this screen depicts input chan-

nels, the contents are the same as the OUTPUT VIEW

function SIGNAL FLOW screen. Refer to p.272.

C Direct out

This area displays information about the direct output

of the two selected channels (the signal output posi-

tion, the port patched to direct out, and the direct

output on/off status).

Here you can also select the signal output position (use

the / buttons at left and right), and switch direct

output on/off (use the ON/OFF button).

D Level meters

These meters indicate the levels at various points in the

signal flow. Levels are detected at the following

locations.

• PRE ATT (immediately before the attenuator)

• EQ (immediately before and after the EQ)

• GATE (immediately before and after the gate)

• COMP (immediately before and after the

compressor)

• FADER (immediately before and after the fader)

• POST ON (immediately after the CH [ON] key)

• INSERT IN (immediately after the insert point)

E Signal flow

This area indicates the signal flow of the selected chan-

nel. The following parameters are displayed.

• ATT (Attenuation)

Specifies the amount of attenuation immediately after

AD conversion for the corresponding channel.

• HPF (High Pass Filter)

Specifies the high pass filter on/off and cutoff fre-

quency for the corresponding channel.

• EQ (Equalizer)

• GATE

• COMP (Compressor)

These areas show the approximate response of the

equalizer, gate, and compressor for the corresponding

channel. You can also switch these on/off in this screen,

or click a mini-graph to access the individual parame-

ter screen.

• DELAY

Here you can switch the internal delay on/off and edit

the delay time.

• FADER

This indicates the input level of the channel. This is

linked with the encoder or fader of the corresponding

channel.

• ON/OFF (On/off)

Turns the channel on/off. This is linked with the [ON]

key of the corresponding channel.

• TO STEREO

Here you can specify the on/off status and pan settings

of the signal sent from the corresponding channel to

the STEREO bus. These are linked with the [TO STE-

REO] key and STEREO [PAN] encoder of the

corresponding channel.

Hint

• If insert or direct out is turned on, the current insert point or

direct out point within the signal flow is shown.

• If the signal clips, the signal flow (horizontal line) after clip-

ping is displayed in red. If an output is turned off so that the

signal does not flow any further, the subsequent flow is dis-

played in gray. If PEAK HOLD is on, the flow indication will

stay red if clipping occurs even once, making it easier to see

that clipping has occurred.

SIGNAL FLOW screen

SIGNAL FLOW

1 32

INPUT VIEW function

314 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

This screen shows the on/off status, level, and cue monitor

status of the input channels and DCA groups.

Except for the fact that this screen is for input channels,

DCA groups, and STEREO A/B channels, this is the same

as the OUTPUT VIEW function FADER VIEW screen.

Refer to p.273.

In this screen you can copy the desired parameter(s) from

the selected input channel into a memory buffer, and paste

or move them to the same type of channel (you may select

more than one paste-destination).

A JOB SELECT

Here you can select either Copy or Move as the

operation.

• COPY

The copy-source channel will remain; its parameters

will be copied to another channel.

• MOVE

The parameters will be moved to another channel.

Note

When you execute the channel move operation, the channels

between the selected channel and the move-destination chan-

nel will also move forward or backward.

FADER VIEW screen

FADER VIEW

CH JOB screen

CH JOB

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 315

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

B CAPTURE

When you click this button, the settings of the cur-

rently selected channel will be copied to a temporary

memory buffer. If you selected the MOVE operation,

this will be grayed, and copying will not be possible.

If the corresponding INPUT channel is paired (or if a

ST IN/FX RTN channel is selected), a heart symbol is

shown at the right.

C BUFFERED CH (Channel in the buffer)

This shows the channel that is currently copied into

buffer memory. If you selected the MOVE operation,

this will be grayed.

Note

• The same buffer memory is used to copy channel settings

for both input channels and output channels.

• If output channel settings have been copied to the buffer

memory, a message of “TYPE CONFLICT!” is displayed

below, and you cannot paste to an input channel.

• The contents of the buffer memory are erased when the

PM5D is powered-off.

D EXECUTE

When you click this button, the specified parameters

will be copied from buffer memory to the specified

paste-destination channel. If you click this button

when performing a MOVE operation, the parameters

of the selected channel will be moved to the specified

move-destination channel.

If an output channel is copied to buffer memory, or if

no paste-destination has been specified, this is grayed-

out and the Paste operation is unavailable.

Note

•A single channel can be moved only if the following two con-

ditions are satisfied.

- There are no paired channels between the move-source

and move-destination.

- You have not selected a parameter of which only one

exists for every two adjacent odd-numbered/even-num-

bered channels, such as DELAY GANG.

• Channels can be moved only within the following channel

sections (on each machine)

- INPUT channels 1–48

- ST IN channels 1–4

- FX RTN channels1–4

E PARAMETER SELECT

Here you can select the parameter(s) that will be

pasted. You can’t select this for the MOVE operation.

You can select the following parameters.

If the SEND button is on, use the MIX buttons (1–24)

to select the target MIX bus.

F CH SELECT (Channel selection)

Here you can select the paste/move-destination chan-

nel(s). You can only select channels of the same type as

the copy/move-source.

Hint

If the copy/move-source INPUT channel is paired, the odd-

numbered channel is copied to the odd-numbered channel(s),

and the even-numbered channel is copied to the even-num-

bered channel(s).

G SET ALL

Specifies the paste-destination as all channels of the

same type as the copy-source. You can’t select this for

the MOVE operation.

H CLEAR ALL

De-selects all channels. You can’t select this for the

MOVE operation.

ALL All parameters

ATT Attenuator settings

EQ EQ function settings

COMP COMP function settings

DELAY DELAY function settings

FADER Fader level

ON CH [ON] key on/off status

PAN/BAL Pan/balance settings

INSERT Insert on/off status and insert point

SEND Send level to the desired MIX bus(es)

DCA Associated DCA group

MUTE Associated mute group

LCR LCR screen settings

HA HA library settings

PATCH Input patch settings

NAME Channel name

INPUT VIEW function

316 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

Here you can recall, store, rename, or delete items in the

input channel library.

Except for the fact that these settings are for input chan-

nels, this is the same as the OUTPUT VIEW function CH

LIBRARY screen. Refer to p.275.

INPUT CH LIBRARY (Input channel

library) screen

INPUT CH LIBRARY

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 317

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

EQ Library List

Appendices

#Title

Parameter

LOW L-MID H-MID HIGH

Bass Drum

PEAKING PEAKING PEAKING H.SHELF

G +3.5 dB –3.5 dB 0.0 dB +4.0 dB

F 100 Hz 265 Hz 1.06 kHz 5.30 kHz

Q 1.25 10.0 0.90 —

Bass Drum

PEAKING PEAKING PEAKING LPF

G +8.0 dB –7.0 dB +6.0 dB ON

F 80.0 Hz 400 Hz 2.50 kHz 12.5 kHz

Q 1.4 4.5 2.2 —

Snare

Drum 1

PEAKING PEAKING PEAKING H.SHELF

G –0.5 dB 0.0 dB +3.0 dB +4.5 dB

F 132 Hz 1.00 kHz 3.15 kHz 5.00 kHz

Q 1.25 4.5 0.11 —

Snare

Drum 2

L.SHELF PEAKING PEAKING PEAKING

G +1.5 dB –8.5 dB +2.5 dB +4.0 dB

F 180 Hz 335 Hz 2.36 kHz 4.00 kHz

Q — 10.0 0.70 0.10

05 Tom-tom 1

PEAKING PEAKING PEAKING PEAKING

G +2.0 dB –7.5 dB +2.0 dB +1.0 dB

F 212 Hz 670 Hz 4.50 kHz 6.30 kHz

Q 1.4 10.0 1.25 0.28

06 Cymbal

L.SHELF PEAKING PEAKING H.SHELF

G –2.0 dB 0.0 dB 0.0 dB +3.0 dB

F 106 Hz 425 Hz 1.06 kHz 13.2 kHz

Q — 8.0 0.90 —

07 High Hat

L.SHELF PEAKING PEAKING H.SHELF

G –4.0 dB –2.5 dB +1.0 dB +0.5 dB

F 95 Hz 425 Hz 2.80 kHz 7.50 kHz

Q — 0.50 1.0 —

08 Percussion

L.SHELF PEAKING PEAKING H.SHELF

G –4.5 dB 0.0 dB +2.0 dB 0.0 dB

F 100 Hz 400 Hz 2.80 kHz 17.0 kHz

Q — 4.5 0.56 —

09 E. Bass 1

L.SHELF PEAKING PEAKING H.SHELF

G –7.5 dB +4.5 dB +2.5 dB 0.0 dB

F 35.5 Hz 112 Hz 2.00 kHz 4.00 kHz

Q — 5.0 4.5 —

10 E. Bass 2

PEAKING PEAKING PEAKING H.SHELF

G +3.0 dB 0.0 dB +2.5 dB +0.5 dB

F 112 Hz 112 Hz 2.24 kHz 4.00 kHz

Q 0.10 5.0 6.3 —

11 Syn. Bass 1

PEAKING PEAKING PEAKING H.SHELF

G +3.5 dB +8.5 dB 0.0 dB 0.0 dB

F 85 Hz 950 Hz 4.00 kHz 12.5 kHz

Q 0.10 8.0 4.5 —

12 Syn. Bass 2

PEAKING PEAKING PEAKING H.SHELF

G +2.5 dB 0.0 dB +1.5 dB 0.0 dB

F 125 Hz 180 Hz 1.12 kHz 12.5 kHz

Q 1.6 8.0 2.2 —

13 Piano 1

L.SHELF PEAKING PEAKING H.SHELF

G –6.0 dB 0.0 dB +2.0 dB +4.0 dB

F 95 Hz 950 Hz 3.15 kHz 7.50 kHz

Q — 8.0 0.90 —

14 Piano 2

PEAKING PEAKING PEAKING H.SHELF

G +3.5 dB –8.5 dB +1.5 dB +3.0 dB

F 224 Hz 600 Hz 3.15 kHz 5.30 kHz

Q 5.6 10.0 0.70 —

15 E. G. Clean

PEAKING PEAKING PEAKING H.SHELF

G +2.0 dB –5.5 dB +0.5 dB +2.5 dB

F 265 Hz 400 Hz 1.32 kHz 4.50 kHz

Q 0.18 10.0 6.3 —

E. G.

Crunch 1

PEAKING PEAKING PEAKING PEAKING

G +4.5 dB 0.0 dB +4.0 dB +2.0 dB

F 140 Hz 1.00 kHz 1.90 kHz 5.60 kHz

Q 8.0 4.5 0.63 9.0

E. G.

Crunch 2

PEAKING PEAKING PEAKING H.SHELF

G +2.5 dB +1.5 dB +2.5 dB 0.0 dB

F 125 Hz 450 Hz 3.35 kHz 19.0 kHz

Q 8.0 0.40 0.16 —

18 E. G. Dist. 1

L.SHELF PEAKING PEAKING H.SHELF

G +5.0 dB 0.0 dB +3.5 dB 0.0 dB

F 355 Hz 950 Hz 3.35 kHz 12.5 kHz

Q — 9.0 10.0 —

19 E. G. Dist. 2

L.SHELF PEAKING PEAKING H.SHELF

G +6.0 dB –8.5 dB +4.5 dB +4.0 dB

F 315 Hz 1.06 kHz 4.25 kHz 12.5 kHz

Q — 10.0 4.0 —

A. G.

Stroke 1

PEAKING PEAKING PEAKING H.SHELF

G –2.0 dB 0.0 dB +1.0 dB +4.0 dB

F 106 Hz 1.00 kHz 1.90 kHz 5.30 kHz

Q 0.9 4.5 3.5 —

A. G.

Stroke 2

L.SHELF PEAKING PEAKING H.SHELF

G –3.5 dB –2.0 dB 0.0 dB +2.0 dB

F 300 Hz 750 Hz 2.00 kHz 3.55 kHz

Q — 9.0 4.5 —

A. G.

Arpeg. 1

L.SHELF PEAKING PEAKING PEAKING

G –0.5 dB 0.0 dB 0.0 dB +2.0 dB

F 224 Hz 1.00 kHz 4.00 kHz 6.70 kHz

Q — 4.5 4.5 0.125

A. G.

Arpeg. 2

L.SHELF PEAKING PEAKING H.SHELF

G 0.0 dB –5.5 dB 0.0 dB +4.0 dB

F 180 Hz 355 Hz 4.00 kHz 4.25 kHz

Q — 7.0 4.5 —

24 Brass Sec.

PEAKING PEAKING PEAKING PEAKING

G –2.0 dB –1.0 dB +1.5 dB +3.0 dB

F 90 Hz 850 Hz 2.12 kHz 4.50 kHz

Q 2.8 2.0 0.70 7.0

Male Vocal

PEAKING PEAKING PEAKING PEAKING

G –0.5 dB 0.0 dB +2.0 dB +3.5 dB

F 190 Hz 1.00 kHz 2.00 kHz 6.70 kHz

Q 0.11 4.5 0.56 0.11

Male Vocal

PEAKING PEAKING PEAKING H.SHELF

G +2.0 dB –5.0 dB –2.5 dB +4.0 dB

F 170 Hz 236 Hz 2.65 kHz 6.70 kHz

Q 0.11 10.0 5.6 —

#Title

Parameter

LOW L-MID H-MID HIGH

GATE Library List

318 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

GATE Library List

Female Vo.

PEAKING PEAKING PEAKING PEAKING

G –1.0 dB +1.0 dB +1.5 dB +2.0 dB

F 118 Hz 400 Hz 2.65 kHz 6.00 kHz

Q 0.18 0.45 0.56 0.14

Female Vo.

L.SHELF PEAKING PEAKING H.SHELF

G –7.0 dB +1.5 dB +1.5 dB +2.5 dB

F 112 Hz 335 Hz 2.00 kHz 6.70 kHz

Q — 0.16 0.20 —

Chorus &

Harmo

PEAKING PEAKING PEAKING PEAKING

G –2.0 dB –1.0 dB +1.5 dB +3.0 dB

F 90.0 Hz 850 Hz 2.12 kHz 4.50 kHz

Q 2.8 2.0 0.70 7.0

30 Total EQ 1

PEAKING PEAKING PEAKING H.SHELF

G –0.5 dB 0.0 dB +3.0 dB +6.5 dB

F 95.0 Hz 950 Hz 2.12 kHz 16.0 kHz

Q 7.0 2.2 5.6 —

31 Total EQ 2

PEAKING PEAKING PEAKING H.SHELF

G +4.0 dB +1.5 dB +2.0 dB +6.0 dB

F 95 Hz 750 Hz 1.80 kHz 18.0 kHz

Q 7.0 2.8 5.6 —

32 Total EQ 3

L.SHELF PEAKING PEAKING H.SHELF

G +1.5 dB +0.5 dB +2.0 dB +4.0 dB

F 67.0 Hz 850 Hz 1.90 kHz 15.0 kHz

Q — 0.28 0.70 —

Bass Drum

PEAKING PEAKING PEAKING PEAKING

G +3.5 dB –10.0 dB +3.5 dB 0.0 dB

F 118 Hz 315 Hz 4.25 kHz 20.0 kHz

Q 2.0 10.0 0.40 0.40

Snare

Drum 3

L.SHELF PEAKING PEAKING PEAKING

G 0.0 dB +2.0 dB +3.5 dB 0.0 dB

F 224 Hz 560 Hz 4.25 kHz 4.00 kHz

Q — 4.5 2.8 0.10

35 Tom-tom 2

L.SHELF PEAKING PEAKING H.SHELF

G –9.0 dB +1.5 dB +2.0 dB 0.0 dB

F 90.0 Hz 212 Hz 5.30 kHz 17.0 kHz

Q — 4.5 1.25 —

36 Piano 3

PEAKING PEAKING PEAKING H.SHELF

G +4.5 dB –13.0 dB +4.5 dB +2.5 dB

F 100 Hz 475 Hz 2.36 kHz 10.0 kHz

Q 8.0 10.0 9.0 —

37 Piano Low

PEAKING PEAKING PEAKING H.SHELF

G –5.5 dB +1.5 dB +6.0 dB 0.0 dB

F 190 Hz 400 Hz 6.70 kHz 12.5 kHz

Q 10.0 6.3 2.2 —

38 Piano High

PEAKING PEAKING PEAKING PEAKING

G –5.5 dB +1.5 dB +5.0 dB +3.0 dB

F 190 Hz 400 Hz 6.70 kHz 5.60 kHz

Q 10.0 6.3 2.2 0.10

Fine-EQ

Cass

L.SHELF PEAKING PEAKING H.SHELF

G –1.5 dB 0.0 dB +1.0 dB +3.0 dB

F 75.0 Hz 1.00 kHz 4.00 kHz 12.5 kHz

Q — 4.5 1.8 —

40 Narrator

PEAKING PEAKING PEAKING H.SHELF

G –4.0 dB –1.0 dB +2.0 dB 0.0 dB

F 106 Hz 710 Hz 2.50 kHz 10.0 kHz

Q 4.0 7.0 0.63 —

#Title

Parameter

LOW L-MID H-MID HIGH

#Title Type Parameter Value

1 Gate GATE

Threshold (dB) –26

Range (dB) –56

Attack (ms) 0

Hold (ms) 2.56

Decay (ms) 331

2 Ducking DUCKING

Threshold (dB) –19

Range (dB) –22

Attack (ms) 93

Hold (ms) 1.20 S

Decay (ms) 6.32 S

3 A. Dr. BD GATE

Threshold (dB) –11

Range (dB) –53

Attack (ms) 0

Hold (ms) 1.93

Decay (ms) 400

4 A. Dr. SN GATE

Threshold (dB) –8

Range (dB) –23

Attack (ms) 1

Hold (ms) 0.63

Decay (ms) 238

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 319

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

Compressor Library List

#Title Type Parameter Value

1 Comp COMP

Threshold (dB) –8

Ratio ( :1) 2.5

Attack (ms) 30

Out gain (dB) 0.0

Knee 2

Release (ms) 250

2 Expand EXPAND

Threshold (dB) –23

Ratio ( :1) 1.7

Attack (ms) 1

Out gain (dB) 3.5

Knee 2

Release (ms) 70

Compander

(H)

COMPAND-H

Threshold (dB) –10

Ratio ( :1) 3.5

Attack (ms) 1

Out gain (dB) 0.0

Width (dB) 6

Release (ms) 250

Compander

(S)

COMPAND-S

Threshold (dB) –8

Ratio ( :1) 4

Attack (ms) 25

Out gain (dB) 0.0

Width (dB) 24

Release (ms) 180

5 A. Dr. BD COMP

Threshold (dB) –24

Ratio ( :1) 3

Attack (ms) 9

Out gain (dB) 5.5

Knee 2

Release (ms) 58

6 A. Dr. BD COMPAND-H

Threshold (dB) –11

Ratio ( :1) 3.5

Attack (ms) 1

Out gain (dB) –1.5

Width (dB) 7

Release (ms) 192

7 A. Dr. SN COMP

Threshold (dB) –17

Ratio ( :1) 2.5

Attack (ms) 8

Out gain (dB) 3.5

Knee 2

Release (ms) 12

8 A. Dr. SN EXPAND

Threshold (dB) –23

Ratio ( :1) 2

Attack (ms) 0

Out gain (dB) 0.5

Knee 2

Release (ms) 151

9 A. Dr. SN COMPAND-S

Threshold (dB) –8

Ratio ( :1) 1.7

Attack (ms) 11

Out gain (dB) 0.0

Width (dB) 10

Release (ms) 128

10 A. Dr. Tom EXPAND

Threshold (dB) –20

Ratio ( :1) 2

Attack (ms) 2

Out gain (dB) 5.0

Knee 2

Release (ms) 749

A. Dr.

OverTop

COMPAND-S

Threshold (dB) –24

Ratio ( :1) 2

Attack (ms) 38

Out gain (dB) –3.5

Width (dB) 54

Release (ms) 842

12 E. B. Finger COMP

Threshold (dB) –12

Ratio ( :1) 2

Attack (ms) 15

Out gain (dB) 4.5

Knee 2

Release (ms) 470

13 E. B. Slap COMP

Threshold (dB) –12

Ratio ( :1) 1.7

Attack (ms) 6

Out gain (dB) 4.0

Knee hard

Release (ms) 133

14 Syn. Bass COMP

Threshold (dB) –10

Ratio ( :1) 3.5

Attack (ms) 9

Out gain (dB) 3.0

Knee hard

Release (ms) 250

15 Piano1 COMP

Threshold (dB) –9

Ratio ( :1) 2.5

Attack (ms) 17

Out gain (dB) 1.0

Knee hard

Release (ms) 238

16 Piano2 COMP

Threshold (dB) –18

Ratio ( :1) 3.5

Attack (ms) 7

Out gain (dB) 6.0

Knee 2

Release (ms) 174

17 E. Guitar COMP

Threshold (dB) –8

Ratio ( :1) 3.5

Attack (ms) 7

Out gain (dB) 2.5

Knee 4

Release (ms) 261

18 A. Guitar COMP

Threshold (dB) –10

Ratio ( :1) 2.5

Attack (ms) 5

Out gain (dB) 1.5

Knee 2

Release (ms) 238

19 Strings1 COMP

Threshold (dB) –11

Ratio ( :1) 2

Attack (ms) 33

Out gain (dB) 1.5

Knee 2

Release (ms) 749

20 Strings2 COMP

Threshold (dB) –12

Ratio ( :1) 1.5

Attack (ms) 93

Out gain (dB) 1.5

Knee 4

Release (ms) 1.35 S

#Title Type Parameter Value

Compressor Library List

320 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

* When fs=44.1 kHz

21 Strings3 COMP

Threshold (dB) –17

Ratio ( :1) 1.5

Attack (ms) 76

Out gain (dB) 2.5

Knee 2

Release (ms) 186

22 BrassSection COMP

Threshold (dB) –18

Ratio ( :1) 1.7

Attack (ms) 18

Out gain (dB) 4.0

Knee 1

Release (ms) 226

23 Syn. Pad COMP

Threshold (dB) –13

Ratio ( :1) 2

Attack (ms) 58

Out gain (dB) 2.0

Knee 1

Release (ms) 238

24 SamplingPerc COMPAND-S

Threshold (dB) –18

Ratio ( :1) 1.7

Attack (ms) 8

Out gain (dB) –2.5

Width (dB) 18

Release (ms) 238

25 Sampling BD COMP

Threshold (dB) –14

Ratio ( :1) 2

Attack (ms) 2

Out gain (dB) 3.5

Knee 4

Release (ms) 35

26 Sampling SN COMP

Threshold (dB) –18

Ratio ( :1) 4

Attack (ms) 8

Out gain (dB) 8.0

Knee hard

Release (ms) 354

27 Hip Comp COMPAND-S

Threshold (dB) –23

Ratio ( :1) 20

Attack (ms) 15

Out gain (dB) 0.0

Width (dB) 15

Release (ms) 163

28 Solo Vocal1 COMP

Threshold (dB) –20

Ratio ( :1) 2.5

Attack (ms) 31

Out gain (dB) 2.0

Knee 1

Release (ms) 342

29 Solo Vocal2 COMP

Threshold (dB) –8

Ratio ( :1) 2.5

Attack (ms) 26

Out gain (dB) 1.5

Knee 3

Release (ms) 331

30 Chorus COMP

Threshold (dB) –9

Ratio ( :1) 1.7

Attack (ms) 39

Out gain (dB) 2.5

Knee 2

Release (ms) 226

#Title Type Parameter Value

31 Click Erase EXPAND

Threshold (dB) –33

Ratio ( :1) 2

Attack (ms) 1

Out gain (dB) 2.0

Knee 2

Release (ms) 284

32 Announcer COMPAND-H

Threshold (dB) –14

Ratio ( :1) 2.5

Attack (ms) 1

Out gain (dB) –2.5

Width (dB) 18

Release (ms) 180

33 Limiter1 COMPAND-S

Threshold (dB) –9

Ratio ( :1) 3

Attack (ms) 20

Out gain (dB) –3.0

Width (dB) 90

Release (ms) 3.91 s

34 Limiter2 COMP

Threshold (dB) 0

Ratio ( :1) ∞

Attack (ms) 0

Out gain (dB) 0.0

Knee hard

Release (ms) 319

35 Total Comp1 COMP

Threshold (dB) –18

Ratio ( :1) 3.5

Attack (ms) 94

Out gain (dB) 2.5

Knee hard

Release (ms) 447

36 Total Comp2 COMP

Threshold (dB) –16

Ratio ( :1) 6

Attack (ms) 11

Out gain (dB) 6.0

Knee 1

Release (ms) 180

#Title Type Parameter Value

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 321

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

Dynamics Parameters

Each channel has a GATE section (input channels and ST IN channels only) and a COMP section. The Gate section includes

Gate and Ducking types. The Comp section includes Compressor, Expander, Compander Hard (COMP. (H)), and Com-

pander Soft (COMP. (S)) types.

❏ GATE

A gate attenuates signals below a set THRESHOLD level by a specified amount (RANGE).

❏ DUCKING

Ducking is commonly used for voice-over applications in which the background music level is reduced automatically when an

announcer speaks. When the KEY IN source signal level exceeds the specified THRESHOLD, the output level is attenuated by

a specified amount (RANGE).

GATE section

Parameter Range Description

THRESHOLD (dB) –72 to 0 (73 points) This determines the level at which the gate effect is applied.

RANGE (dB) –∞, –69 to 0 (71 points) This determines the amount of attenuation when the gate closes.

ATTACK (ms) 0–120 (121 points) This determines how fast the gate opens when the signal exceeds the threshold level.

HOLD (ms)

44.1kHz: 0.02 ms – 2.13 sec

48kHz: 0.02 ms – 1.96 sec

88.2kHz: 0.01 ms – 1.06 sec

96kHz: 0.01 ms – 981 ms (160 points)

This determines how long the gate stays open once the trigger signal has fallen

below the threshold.

DECAY (ms)

44.1kHz: 6 ms – 46.0 sec

48kHz: 5 ms – 42.3 sec

88.2kHz: 3 ms – 23.0 sec

96kHz: 3 ms – 21.1 sec (160 points)

This determines how fast the gate closes once the hold time has expired. The value is

expressed as the duration required for the level to change by 6 dB.

Parameter Range Description

THRESHOLD (dB) –54 to 0 (55 points) This determines the level of trigger signal (KEY IN) required to activate ducking.

RANGE (dB) –70 to 0 (71 points) This determines the amount of attenuation when ducking is activated.

ATTACK (ms) 0–120 (121 points) This determines how soon the signal is ducked once the ducker has been triggered.

HOLD (ms)

44.1kHz: 0.02 ms – 2.13 sec

48kHz: 0.02 ms – 1.96 sec

88.2kHz: 0.01 ms – 1.06 sec

96kHz: 0.01 ms – 981 ms (160 points)

This determines how long ducking remains active once the trigger signal has fallen

below the THRESHOLD level.

DECAY (ms)

44.1kHz: 6 ms – 46.0 sec

48kHz: 5 ms – 42.3 sec

88.2kHz: 3 ms – 23.0 sec

96kHz: 3 ms – 21.1 sec (160 points)

This determines how soon the ducker returns to its normal gain once the trigger sig-

nal level drops below the threshold. The value is expressed as the duration required

for the level to change by 6 dB.

Input Level Time Time

Output Level

Input Level

Output Level

• I/O Characteristics • Time Series Analysis

RANGE

THRESHOLD

RANGE

Input Signal Output Signal

ATTACK DECAY

HOLD

Input Level Time Time

Output Level

Input Level

Output Level

• I/O Characteristics • Time Series Analysis

RANGE

THRESHOLD

RANGE

Input Signal Output Signal

ATTACK DECAY

HOLD

Dynamics Parameters

322 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

❏ Compressor (COMP)

The COMP processor attenuates signals above a specified THRESHOLD by a specified RATIO. The COMP processor can also

be used as a limiter, which, with a RATIO of ∞:1, reduces the level to the threshold. This means that the limiter’s output level

never actually exceeds the threshold.

❏ Expander (EXPAND)

An expander attenuates signals below a specified THRESHOLD by a specified RATIO.

COMP section

Parameter Range Description

THRESHOLD (dB) –54 to 0 (55 points) This determines the level of input signal required to trigger the compressor.

RATIO

1.0:1, 1.1:1, 1.3:1, 1.5:1, 1.7:1, 2.0:1,

2.5:1, 3.0:1, 3.5:1, 4.0:1, 5.0:1, 6.0:1,

8.0:1, 10:1, 20:1, ∞:1 (16 points)

This determines the amount of compression, that is, the change in output signal level

relative to change in input signal level.

ATTACK (ms) 0–120 (121 points)

This determines how soon the signal will be compressed once the compressor has

been triggered.

RELEASE (ms)

44.1kHz: 6 ms – 46.0 sec

48kHz: 5 ms – 42.3 sec

88.2kHz: 3 ms – 23.0 sec

96kHz: 3 ms – 21.1 sec (160 points)

This determines how soon the compressor returns to its normal gain once the trigger

signal level drops below the threshold. The value is expressed as the duration

required for the level to change by 6 dB.

OUT GAIN (dB) 0.0 to +18.0 (181 points) This sets the compressor’s output signal level.

KNEE Hard, 1–5 (6 points)

This determines how compression is applied at the threshold. For higher knee set-

tings, compression is applied gradually as the signal exceeds the speciﬁed threshold,

creating a more natural sound.

Input Level Time Time

Output Level

Input Level

Output Level

• Time Series Analysis (RATIO= ∞:1)

RATIO

THRESHOLD

Input signal Output Signal

ATTACK RELEASE

• I/O Characteristics

(KNEE= hard, OUT GAIN=0.0dB)

Parameter Range Description

THRESHOLD (dB) –54 to 0 (55 points) This determines the level of input signal required to trigger the expander.

RATIO

1.0:1, 1.1:1, 1.3:1, 1.5:1, 1.7:1, 2.0:1,

2.5:1, 3.0:1, 3.5:1, 4.0:1, 5.0:1, 6.0:1,

8.0:1, 10:1, 20:1, ∞:1 (16 points)

This determines the amount of expansion.

ATTACK (ms) 0–120 (121 points)

This determines how soon the expander returns to its normal gain once the trigger

signal level exceeds the threshold.

RELEASE (ms)

44.1kHz: 6 ms – 46.0 sec

48kHz: 5 ms – 42.3 sec

88.2kHz: 3 ms – 23.0 sec

96kHz: 3 ms – 21.1 sec (160 points)

This determines how soon the signal is expanded once the signal level drops below

the threshold. The value is expressed as the duration required for the level to change

by 6 dB.

OUT GAIN (dB) 0.0 to +18.0 (181 points) This sets the expander’s output signal level.

KNEE Hard, 1–5 (6 points)

This determines how expansion is applied at the threshold. For higher knee settings,

expansion is applied gradually as the signal falls below the speciﬁed threshold, creat-

ing a more natural sound.

Input Level Time Time

Output Level

Input Level

Output Level

• I/O Characteristics

(KNEE= hard, OUT GAIN= 0.0dB)

• Time Series Analysis (RATIO= ∞:1)

RATIO

THRESHOLD

Input Signal Output Signal

ATTACK RELEASE

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 323

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

❏ COMPANDER HARD (COMP.(H))

❏ COMPANDER SOFT (COMP.(S))

The hard and soft companders combine the effects of the compressor, expander and limiter.

The companders function differently at the following levels:

1 0 dB and higher . . . . . . . . . . . . . . . . . . Functions as a limiter.

2 Exceeding the threshold . . . . . . . . . . Functions as a compressor.

3 Below the threshold and width . . . . Functions as an expander.

The hard compander has an expansion ratio of 5:1, while the soft compander has an expansion ratio of 1.5:1. The expander is

essentially turned off when the width is set to maximum. The compressor has a fixed knee setting of 2.

* The gain is automatically adjusted according to the ratio and threshold values, and can be increased by up to 18 dB.

* The OUT GAIN parameter enables you to compensate for the overall level change caused by the compression and expan-

sion processes.

Parameter Range Description

THRESHOLD (dB) –54 to 0 (55 points) This determines the level at which compression is applied.

RATIO

1.0:1, 1.1:1, 1.3:1, 1.5:1, 1.7:1, 2.0:1,

2.5:1, 3.0:1, 3.5:1, 4.0:1, 5.0:1, 6.0:1,

8.0:1, 10:1, 20:1, (15 points)

This determines the amount of compression.

ATTACK (ms) 0–120 (121 points)

This determines how soon the signal is compressed or expanded once the com-

pander has been triggered.

RELEASE (ms)

44.1kHz: 6 ms – 46.0 sec

48kHz: 5 ms – 42.3 sec

88.2kHz: 3 ms – 23.0 sec

96kHz: 3 ms – 21.1 sec (160 points)

This determines how soon the compressor or expander returns to the normal gain

once the trigger signal level drops below or exceeds the threshold respectively. The

value is expressed as the duration required for the level to change by 6 dB.

OUT GAIN (dB) –18.0 to 0.0 (181 points) This sets the compander’s output signal level.

WIDTH (dB) 1–90 (90 points)

This determines how far below the threshold expansion will be applied. The expander

is activated when the level drops below the threshold and width.

0dB

Input Level

Output Level

THRESHOLD

WIDTH

Effect Library List

324 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

Effect Library List

This is a list of the built-in effects.

No. Title Type Description

001 Reverb Hall REVERB HALL

Concert hall reverberation

simulation with gate

002 Reverb Room REVERB ROOM

Room reverberation simula-

tion with gate

003 Reverb Stage REVERB STAGE

Reverb designed for vocals,

with gate

004 Reverb Plate REVERB PLATE

Plate reverb simulation with

gate

005 Early Ref. EARLY REF.

Early reﬂections without the

subsequent reverb

006 Gate Reverb GATE REVERB Gated early reﬂections

007 Reverse Gate REVERSE GATE

Gated reverse early reﬂec-

tions

008 Mono Delay MONO DELAY Simple mono delay

009 Stereo Delay STEREO DELAY Simple stereo delay

010 Mod.Delay MOD.DELAY

Simple repeat delay with

modulation

011 Delay LCR DELAY LCR

3-tap (left, center, right)

delay

012 Echo ECHO

Stereo delay with crossed

left/right feedback

013 Chorus CHORUS Chorus

014 Flange FLANGE Flanger

015 Symphonic SYMPHONIC

Proprietary Yamaha effect

that produces a richer and

more complex modulation

than normal chorus

016 Phaser PHASER

16-stage stereo phase

shifter

017 Auto Pan AUTO PAN Auto-panner

018 Tremolo TREMOLO Tremolo

019 HQ. Pitch HQ.PITCH

Mono pitch shifter, produc-

ing stable results

020 Dual Pitch DUAL PITCH Stereo pitch shifter

021 Rotary ROTARY Rotary speaker simulation

022 Ring Mod. RING MOD. Ring modulator

023 Mod.Filter MOD.FILTER Modulated ﬁlter

024 Distortion DISTORTION Distortion

025 Amp Simulate AMP SIMULATE Guitar amp simulation

026 Dyna.Filter DYNA.FILTER Dynamically controlled ﬁlter

027 Dyna.Flange DYNA.FLANGE

Dynamically controlled

ﬂanger

028 Dyna.Phaser DYNA.PHASER

Dynamically controlled

phase shifter

029 Rev+Chorus REV+CHORUS

Reverb and chorus in paral-

lel

030 Rev→Chorus REV→CHORUS Reverb and chorus in series

031 Rev+Flange REV+FLANGE

Reverb and ﬂanger in paral-

lel

032 Rev→Flange REV→FLANGE Reverb and ﬂanger in series

033 Rev+Sympho. REV+SYMPHO.

Reverb and symphonic in

parallel

034 Rev→Sympho. REV→SYMPHO.

Reverb and symphonic in

series

035 Rev→Pan REV→PAN

Reverb and auto-pan in

series

036 Delay+Er. DELAY+ER.

Delay and early reﬂections

in parallel

037 Delay+Er. DELAY→ER.

Delay and early reﬂections

in series

038 Delay+Rev DELAY+REV Delay and reverb in parallel

039 Delay→Rev DELAY→REV Delay and reverb in series

040 Dist→Delay DIST→DELAY

Distortion and delay in

series

041 Multi.Filter MULTI.FILTER

3-band parallel ﬁlter (24 dB/

octave)

042 Freeze FREEZE Simple sampler

043 Stereo Reverb ST REVERB Stereo reverb

044 M.Band Dyna. M.BAND DYNA.

Multi-band dynamics pro-

cessor

045 M.Band Comp M.BAND COMP Multi-band compressor

046 REV-X Hall

REV-X HALL

New reverb algorithm that

delivers dense and rich

reverberation, smooth

decay, and provides a spa-

ciousness and depth that

enhances the original

sound. Choose from three

types depending on your

location and needs; REV-X

HALL, REV-X ROOM, and

REV-X PLATE.

047 REV-X Room

REV-X ROOM

048 REV-X Plate

REV-X PLATE

049 Comp276 COMP276

This compressor emulates

the characteristics of an

analog compressor that has

become a sought-after clas-

sic in recording studios.

050 Comp276S COMP276S

This is a stereo model of

COMP276.

051 Comp260 COMP260

This compressor emulates

the characteristics of a com-

pressor/limiter of the latter

1970s that has become a

sought-after classic for live

SR.

052 Comp260S COMP260S

This is a stereo model of the

COMP260.

053 Equalizer601 EQUALIZER601

This equalizer emulates the

characteristics of an analog

equalizer of the 1970s. It

can be used to obtain a

sense of drive.

054 OpenDeck OPENDECK

This is a tape saturation

effect that emulates the

tape compression pro-

duced by two open-reel

tape recorders: a recording

deck and a reproduction

deck.

055 De-Esser DE-ESSER

This detects and compresses

only the high-frequency

consonant portions such as

the sibilance of a vocal.

No. Title Type Description

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 325

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

Effects Parameters

❏ REVERB HALL, REVERB ROOM, REVERB

STAGE, REVERB PLATE

One input, two output hall, room, stage, and plate reverb

simulations, all with gates.

❏ EARLY REF.

One input, two output early reflections.

❏ GATE REVERB, REVERSE GATE

One input, two output early reflections with gate, and early

reflections with reverse gate.

❏ MONO DELAY

One input, one output basic repeat delay.

❏ STEREO DELAY

Two input, two output basic stereo delay.

Parameter Range Description

REV TIME 0.3–99.0 s Reverb time

INI. DLY 0.0–500.0 ms

Initial delay before reverb

begins

HI. RATIO 0.1–1.0

High-frequency reverb time

ratio

LO. RATIO 0.1–2.4

Low-frequency reverb time

ratio

DIFF. 0–10

Reverb diffusion (left–right

reverb spread)

DENSITY 0–100% Reverb density

E/R DLY 0.0–100.0 ms

Delay between early reﬂec-

tions and reverb

E/R BAL. 0–100%

Balance of early reﬂections

and reverb

(0% = all reverb, 100% = all

early reﬂections)

HPF THRU, 21.2 Hz–8.00 kHz

High-pass ﬁlter cutoff fre-

quency

LPF 50.0 Hz–16.0 kHz, THRU

Low-pass ﬁlter cutoff fre-

quency

GATE LVL OFF, –60 to 0 dB Level at which gate kicks in

ATTACK 0–120 ms Gate opening speed

HOLD

*1. 0.02 ms–2.13 s (fs=44.1 kHz), 0.02 ms–1.96 s (fs=48 kHz),

0.01 ms–1.06 s (fs=88.2 kHz), 0.01 ms–981 ms (fs=96 kHz)

Gate open time

DECAY

*2. 6.0 ms–46.0 s (fs=44.1 kHz), 5.0 ms–42.3 s (fs=48 kHz),

3 ms–23.0 s (fs=88.2 kHz), 3 ms–21.1 s (fs=96 kHz)

Gate closing speed

Parameter Range Description

TYPE

S-Hall, L-Hall, Random,

Revers, Plate, Spring

Type of early reﬂection sim-

ulation

ROOMSIZE 0.1–20.0 Reﬂection spacing

LIVENESS 0–10

Early reﬂections decay char-

acteristics (0 = dead, 10 =

live)

INI. DLY 0.0–500.0 ms

Initial delay before reverb

begins

DIFF. 0–10

Reﬂection diffusion (left–

right reﬂection spread)

DENSITY 0–100% Reﬂection density

ER NUM. 1–19 Number of early reﬂections

FB GAIN –99 to +99% Feedback gain

HI. RATIO 0.1–1.0

High-frequency feedback

ratio

HPF THRU, 21.2 Hz–8.00 kHz

High-pass ﬁlter cutoff fre-

quency

LPF 50.0 Hz–16.0 kHz, THRU

Low-pass ﬁlter cutoff fre-

quency

Parameter Range Description

TYPE Type-A, Type-B Type of early reﬂection simulation

ROOMSIZE 0.1–20.0 Reﬂection spacing

LIVENESS 0–10

Early reﬂections decay characteris-

tics (0 = dead, 10 = live)

INI. DLY 0.0–500.0 ms Initial delay before reverb begins

DIFF. 0–10

Reﬂection diffusion (left–right

reﬂection spread)

DENSITY 0–100% Reﬂection density

HI. RATIO 0.1–1.0 High-frequency feedback ratio

ER NUM. 1–19 Number of early reﬂections

FB GAIN –99 to +99% Feedback gain

HPF

THRU, 21.2 Hz–

8.00 kHz

High-pass ﬁlter cutoff frequency

LPF

50.0 Hz–16.0 kHz,

THRU

Low-pass ﬁlter cutoff frequency

Parameter Range Description

DELAY 0.0–2730.0 ms Delay time

FB. GAIN –99 to +99%

Feedback gain (plus values for

normal-phase feedback, minus

values for reverse-phase feedback)

HI. RATIO 0.1–1.0 High-frequency feedback ratio

HPF

THRU, 21.2 Hz–

8.00 kHz

High-pass ﬁlter cutoff frequency

LPF

50.0 Hz–16.0 kHz,

THRU

Low-pass ﬁlter cutoff frequency

SYNC OFF/ON Tempo parameter sync on/off

NOTE

*1.

(Max. value depends on tempo setting)

Used in conjunction with TEMPO

to determine DELAY

Parameter Range Description

DELAY L 0.0–1350.0 ms Left channel delay time

DELAY R 0.0–1350.0 ms Right channel delay time

FB. G L –99 to +99%

Left channel feedback (plus values

for normal-phase feedback, minus

values for reverse-phase feedback)

FB. G R –99 to +99%

Right channel feedback (plus val-

ues for normal-phase feedback,

minus values for reverse-phase

feedback)

HI. RATIO 0.1–1.0 High-frequency feedback ratio

HPF

THRU, 21.2 Hz–

8.00 kHz

High-pass ﬁlter cutoff frequency

LPF

50.0 Hz–16.0 kHz,

THRU

Low-pass ﬁlter cutoff frequency

SYNC OFF/ON Tempo parameter sync on/off

NOTE L

*1.

(Maximum value depends on the tempo setting)

Used in conjunction with TEMPO

to determine left channel DELAY

NOTE R 1

Used in conjunction with TEMPO

to determine right channel DELAY

Effects Parameters

326 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

❏ MOD. DELAY

One input, two output basic repeat delay with modulation.

❏ DELAY LCR

One input, two output 3-tap delay (left, center, right).

❏ ECHO

Two input, two output stereo delay with crossed feedback

loop.

❏ CHORUS

Two input, two output chorus effect.

Parameter Range Description

DELAY 0.0–2725.0 ms Delay time

FB. GAIN –99 to +99%

Feedback gain (plus values for

normal-phase feedback, minus

values for reverse-phase feedback)

HI. RATIO 0.1–1.0 High-frequency feedback ratio

FREQ. 0.05–40.00 Hz Modulation speed

DEPTH 0–100% Modulation depth

WAVE Sine/Tri Modulation waveform

HPF

THRU, 21.2 Hz–

8.00 kHz

High-pass ﬁlter cutoff frequency

LPF

50.0 Hz–16.0 kHz,

THRU

Low-pass ﬁlter cutoff frequency

SYNC OFF/ON Tempo parameter sync on/off

DLY.NOTE

*1.

(Maximum value depends on the tempo setting)

Used in conjunction with TEMPO

to determine DELAY

MOD.NOTE

*2.

Used in conjunction with TEMPO

to determine FREQ

Parameter Range Description

DELAY L 0.0–2730.0 ms Left channel delay time

DELAY C 0.0–2730.0 ms Center channel delay time

DELAY R 0.0–2730.0 ms Right channel delay time

FB. DLY 0.0–2730.0 ms Feedback delay time

LEVEL L –100 to +100% Left channel delay level

LEVEL C –100 to +100% Center channel delay level

LEVEL R –100 to +100% Right channel delay level

FB. GAIN –99 to +99%

Feedback gain (plus values for

normal-phase feedback, minus

values for reverse-phase feedback)

HI. RATIO 0.1–1.0 High-frequency feedback ratio

HPF

THRU, 21.2 Hz–

8.00 kHz

High-pass ﬁlter cutoff frequency

LPF

50.0 Hz–16.0 kHz,

THRU

Low-pass ﬁlter cutoff frequency

SYNC OFF/ON Tempo parameter sync on/off

NOTE L

*1.

(Maximum value depends on the tempo setting)

Used in conjunction with TEMPO

to determine DELAY L

NOTE C 1

Used in conjunction with TEMPO

to determine DELAY C

NOTE R 1

Used in conjunction with TEMPO

to determine DELAY R

NOTE FB 1

Used in conjunction with TEMPO

to determine FB. DLY

Parameter Range Description

DELAY L 0.0–1350.0 ms Left channel delay time

DELAY R 0.0–1350.0 ms Right channel delay time

FB.DLY L 0.0–1350.0 ms Left channel feedback delay time

FB.DLY R 0.0–1350.0 ms Right channel feedback delay time

FB. G L –99 to +99%

Left channel feedback gain (plus

values for normal-phase feedback,

minus values for reverse-phase

feedback)

FB. G R –99 to +99%

Right channel feedback gain (plus

values for normal-phase feedback,

minus values for reverse-phase

feedback)

L→R FBG –99 to +99%

Left to right channel feedback

gain (plus values for normal-phase

feedback, minus values for

reverse-phase feedback)

R→L FBG –99 to +99%

Right to left channel feedback

gain (plus values for normal-phase

feedback, minus values for

reverse-phase feedback)

HI. RATIO 0.1–1.0 High-frequency feedback ratio

HPF

THRU, 21.2 Hz–

8.00 kHz

High-pass ﬁlter cutoff frequency

LPF

50.0 Hz–16.0 kHz,

THRU

Low-pass ﬁlter cutoff frequency

SYNC OFF/ON Tempo parameter sync on/off

NOTE L

*1.

(Maximum value depends on the tempo setting)

Used in conjunction with TEMPO

to determine DELAY L

NOTE R 1

Used in conjunction with TEMPO

to determine DELAY R

NOTE FBL 1

Used in conjunction with TEMPO

to determine FB. D L

NOTE FBR 1

Used in conjunction with TEMPO

to determine FB. D R

Parameter Range Description

FREQ. 0.05–40.00 Hz Modulation speed

AM DEPTH 0–100% Amplitude modulation depth

PM DEPTH 0–100% Pitch modulation depth

MOD. DLY 0.0–500.0 ms Modulation delay time

WAVE Sine, Tri Modulation waveform

LSH F 21.2 Hz–8.00 kHz Low shelving ﬁlter frequency

LSH G –12.0 to +12.0 dB Low shelving ﬁlter gain

EQ F 100 Hz–8.00 kHz EQ (peaking type) frequency

EQ G –12.0 to +12.0 dB EQ (peaking type) gain

EQ Q 10.0–0.10 EQ (peaking type) bandwidth

HSH F 50.0 Hz–16.0 kHz High shelving ﬁlter frequency

HSH G –12.0 to +12.0 dB High shelving ﬁlter gain

SYNC OFF/ON Tempo parameter sync on/off

NOTE

*1.

Used in conjunction with TEMPO

to determine FREQ.

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 327

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

❏ FLANGE

Two input, two output flange effect.

❏ SYMPHONIC

Two input, two output symphonic effect.

❏ PHASER

Two input, two output 16-stage phaser.

❏ AUTOPAN

Two input, two output autopanner.

❏ TREMOLO

Two input, two output tremolo effect.

❏ HQ. PITCH

One input, two output high-quality pitch shifter.

Parameter Range Description

FREQ. 0.05–40.00 Hz Modulation speed

DEPTH 0–100% Modulation depth

MOD. DLY 0.0–500.0 ms Modulation delay time

FB. GAIN –99 to +99%

Feedback gain (plus values for

normal-phase feedback, minus

values for reverse-phase feedback)

WAVE Sine, Tri Modulation waveform

LSH F 21.2 Hz–8.00 kHz Low shelving ﬁlter frequency

LSH G –12.0 to +12.0 dB Low shelving ﬁlter gain

EQ F 100 Hz–8.00 kHz EQ (peaking type) frequency

EQ G –12.0 to +12.0 dB EQ (peaking type) gain

EQ Q 10.0–0.10 EQ (peaking type) bandwidth

HSH F 50.0 Hz–16.0 kHz High shelving ﬁlter frequency

HSH G –12.0 to +12.0 dB High shelving ﬁlter gain

SYNC OFF/ON Tempo parameter sync on/off

NOTE

*1.

Used in conjunction with TEMPO

to determine FREQ.

Parameter Range Description

FREQ. 0.05–40.00 Hz Modulation speed

DEPTH 0–100% Modulation depth

MOD. DLY 0.0–500.0 ms Modulation delay time

WAVE Sine, Tri Modulation waveform

LSH F 21.2 Hz–8.00 kHz Low shelving ﬁlter frequency

LSH G –12.0 to +12.0 dB Low shelving ﬁlter gain

EQ F 100 Hz–8.00 kHz EQ (peaking type) frequency

EQ G –12.0 to +12.0 dB EQ (peaking type) gain

EQ Q 10.0–0.10 EQ (peaking type) bandwidth

HSH F 50.0 Hz–16.0 kHz High shelving ﬁlter frequency

HSH G –12.0 to +12.0 dB High shelving ﬁlter gain

SYNC OFF/ON Tempo parameter sync on/off

NOTE

*1.

Used in conjunction with TEMPO

to determine FREQ.

Parameter Range Description

FREQ. 0.05–40.00 Hz Modulation speed

DEPTH 0–100% Modulation depth

FB. GAIN –99 to +99%

Feedback gain (plus values for

normal-phase feedback, minus

values for reverse-phase feedback)

OFFSET 0–100

Lowest phase-shifted frequency

offset

PHASE

0.00–354.38

degrees

Left and right modulation phase

balance

STAGE

2, 4, 6, 8, 10, 12,

14, 16

Number of phase shift stages

LSH F 21.2 Hz–8.00 kHz Low shelving ﬁlter frequency

LSH G –12.0 to +12.0 dB Low shelving ﬁlter gain

HSH F 50.0 Hz–16.0 kHz High shelving ﬁlter frequency

HSH G –12.0 to +12.0 dB High shelving ﬁlter gain

SYNC OFF/ON Tempo parameter sync on/off

NOTE

*1.

Used in conjunction with TEMPO

to determine FREQ.

Parameter Range Description

FREQ. 0.05–40.00 Hz Modulation speed

DEPTH 0–100% Modulation depth

DIR.

*1. L↔R, L→R, L←R, Turn L, Turn R

Panning direction

WAVE Sine, Tri, Square Modulation waveform

LSH F 21.2 Hz–8.00 kHz Low shelving ﬁlter frequency

LSH G –12.0 to +12.0 dB Low shelving ﬁlter gain

EQ F 100 Hz–8.00 kHz EQ (peaking type) frequency

EQ G –12.0 to +12.0 dB EQ (peaking type) gain

EQ Q 10.0–0.10 EQ (peaking type) bandwidth

HSH F 50.0 Hz–16.0 kHz High shelving ﬁlter frequency

HSH G –12.0 to +12.0 dB High shelving ﬁlter gain

SYNC OFF/ON Tempo parameter sync on/off

NOTE

*2.

Used in conjunction with TEMPO

to determine FREQ.

Parameter Range Description

FREQ. 0.05–40.00 Hz Modulation speed

DEPTH 0–100% Modulation depth

WAVE Sine, Tri, Square Modulation waveform

LSH F 21.2 Hz–8.00 kHz Low shelving ﬁlter frequency

LSH G –12.0 to +12.0 dB Low shelving ﬁlter gain

EQ F 100 Hz–8.00 kHz EQ (peaking type) frequency

EQ G –12.0 to +12.0 dB EQ (peaking type) gain

EQ Q 10.0–0.10 EQ (peaking type) bandwidth

HSH F 50.0 Hz–16.0 kHz High shelving ﬁlter frequency

HSH G –12.0 to +12.0 dB High shelving ﬁlter gain

SYNC OFF/ON Tempo parameter sync on/off

NOTE

*1.

Used in conjunction with TEMPO

to determine FREQ.

Parameter Range Description

PITCH –12 to +12 semitones Pitch shift

FINE –50 to +50 cents Pitch shift ﬁne

DELAY 0.0–1000.0 ms Delay time

FB. GAIN –99 to +99%

Feedback gain (plus values for

normal-phase feedback, minus

values for reverse-phase feed-

back)

MODE 1–10 Pitch shift precision

SYNC OFF/ON Tempo parameter sync on/off

NOTE

*1.

(Maximum value depends on the tempo setting)

Used in conjunction with

TEMPO to determine DELAY

Effects Parameters

328 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

❏ DUAL PITCH

Two input, two output pitch shifter.

❏ ROTARY

One input, two output rotary speaker simulator.

❏ RING MOD.

Two input, two output ring modulator.

❏ MOD. FILTER

Two input, two output modulation filter.

❏ DISTORTION

One input, two output distortion effect.

❏ AMP SIMULATE

One input, two output guitar amp simulator.

❏ DYNA. FILTER

Two input, two output dynamically controlled filter.

Parameter Range Description

PITCH 1 –24 to +24 semitones Channel #1 pitch shift

FINE 1 –50 to +50 cents Channel #1 pitch shift ﬁne

LEVEL 1 –100 to +100%

Channel #1 level (plus values

for normal phase, minus values

for reverse phase)

PAN 1 L63 to R63 Channel #1 pan

DELAY 1 0.0–1000.0 ms Channel #1 delay time

FB. G 1 –99 to +99%

Channel #1 feedback gain (plus

values for normal-phase feed-

back, minus values for

reverse-phase feedback)

PITCH 2 –24 to +24 semitones Channel #2 pitch shift

FINE 2 –50 to +50 cents Channel #2 pitch shift ﬁne

LEVEL 2 –100 to +100%

Channel #2 level (plus values

for normal phase, minus values

for reverse phase)

PAN 2 L63 to R63 Channel #2 pan

DELAY 2 0.0–1000.0 ms Channel #2 delay time

FB. G 2 –99 to +99%

Channel #2 feedback gain (plus

values for normal-phase feed-

back, minus values for

reverse-phase feedback)

MODE 1–10 Pitch shift precision

SYNC OFF/ON Tempo parameter sync on/off

NOTE 1

*1.

(Maximum value depends on the tempo setting)

Used in conjunction with

TEMPO to determine Channel

#1 delay

NOTE 2 1

Used in conjunction with

TEMPO to determine Channel

#2 delay

Parameter Range Description

ROTATE STOP, START Rotation stop, start

SPEED SLOW, FAST

Rotation speed (see SLOW and

FAST parameters)

SLOW 0.05–10.00 Hz SLOW rotation speed

FAST 0.05–10.00 Hz FAST rotation speed

DRIVE 0–100 Overdrive level

ACCEL 0–10 Acceleration at speed changes

LOW 0–100 Low-frequency ﬁlter

HIGH 0–100 High-frequency ﬁlter

Parameter Range Description

SOURCE OSC, SELF

Modulation source: oscillator or

input signal

OSC FREQ 0.0–5000.0 Hz Oscillator frequency

FM FREQ. 0.05–40.00 Hz

Oscillator frequency modulation

speed

FM DEPTH 0–100%

Oscillator frequency modulation

depth

SYNC OFF/ON Tempo parameter sync on/off

NOTE FM

*1.

Used in conjunction with TEMPO

to determine FM FREQ

Parameter Range Description

FREQ. 0.05–40.00 Hz Modulation speed

DEPTH 0–100% Modulation depth

PHASE 0.00–354.38 degrees

Left-channel modulation and

right-channel modulation

phase difference

TYPE LPF, HPF, BPF

Filter type: low pass, high pass,

band pass

OFFSET 0–100 Filter frequency offset

RESO. 0–20 Filter resonance

LEVEL 0–100 Output level

SYNC OFF/ON Tempo parameter sync on/off

NOTE

*1.

Used in conjunction with

TEMPO to determine FREQ

Parameter Range Description

DST TYPE

DST1, DST2, OVD1,

OVD2, CRUNCH

Distortion type (DST = distortion,

OVD = overdrive)

DRIVE 0–100 Distortion drive

MASTER 0–100 Master volume

TONE –10 to +10 Tone

N. GATE 0–20 Noise reduction

Parameter Range Description

AMP TYPE

*1. STK-M1, STK-M2, THRASH, MIDBST, CMB-PG, CMB-VR, CMB-

DX, CMB-TW, MINI, FLAT

Guitar amp simulation type

DST TYPE

DST1, DST2, OVD1,

OVD2, CRUNCH

Distortion type (DST = distortion,

OVD = overdrive)

DRIVE 0–100 Distortion drive

MASTER 0–100 Master volume

BASS 0–100 Bass tone control

MIDDLE 0–100 Middle tone control

TREBLE 0–100 High tone control

CAB DEP 0–100% Speaker cabinet simulation depth

EQ F 100–8.00 kHz EQ (peaking type) frequency

EQ G –12.0 to +12.0 dB EQ (peaking type) gain

EQ Q 10.0–0.10 EQ (peaking type) bandwidth

N. GATE 0–20 Noise reduction

Parameter Range Description

SOURCE INPUT, MIDI

Control source: input signal or

MIDI Note On velocity

SENSE 0–100 Sensitivity

DIR. UP, DOWN

Upward or downward frequency

change

DECAY

*1. 6.0 ms–46.0 s (fs=44.1 kHz), 5.0 ms–42.3 s (fs=48 kHz),

3 ms–23.0 s (fs=88.2 kHz), 3 ms–21.1 s (fs=96 kHz)

Filter frequency change decay

speed

TYPE LPF, HPF, BPF Filter type

OFFSET 0–100 Filter frequency offset

RESO. 0–20 Filter resonance

LEVEL 0–100 Output Level

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 329

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

❏ DYNA. FLANGE

Two input, two output dynamically controlled flanger.

❏ DYNA. PHASER

Two input, two output dynamically controlled phaser.

❏ REV+CHORUS

One input, two output reverb and chorus effects in parallel.

❏ REV→CHORUS

One input, two output reverb and chorus effects in series.

Parameter Range Description

SOURCE INPUT, MIDI

Control source: input signal or

MIDI Note On velocity

SENSE 0–100 Sensitivity

DIR. UP, DOWN

Upward or downward frequency

change

DECAY

*1. 6.0 ms–46.0 s (fs=44.1 kHz), 5.0 ms–42.3 s (fs=48 kHz),

3 ms–23.0 s (fs=88.2 kHz), 3 ms–21.1 s (fs=96 kHz)

Decay speed

OFFSET 0–100 Delay time offset

FB.GAIN –99 to +99%

Feedback gain (plus values for

normal-phase feedback, minus

values for reverse-phase feedback)

LSH F 21.2 Hz–8.00 kHz Low shelving ﬁlter frequency

LSH G –12.0 to +12.0 dB Low shelving ﬁlter gain

EQ F 100 Hz–8.00 kHz EQ (peaking type) frequency

EQ G –12.0 to +12.0 dB EQ (peaking type) gain

EQ Q 10.0–0.10 EQ (peaking type) bandwidth

HSH F 50.0 Hz–16.0 kHz High shelving ﬁlter frequency

HSH G –12.0 to +12.0 dB High shelving ﬁlter gain

Parameter Range Description

SOURCE INPUT, MIDI

Control source: input signal or

MIDI Note On velocity

SENSE 0–100 Sensitivity

DIR. UP, DOWN

Upward or downward frequency

change

DECAY

*1. 6.0 ms–46.0 s (fs=44.1 kHz), 5.0 ms–42.3 s (fs=48 kHz),

3 ms–23.0 s (fs=88.2 kHz), 3 ms–21.1 s (fs=96 kHz)

Decay speed

OFFSET 0–100

Lowest phase-shifted frequency

offset

FB.GAIN –99 to +99%

Feedback gain (plus values for

normal-phase feedback, minus

values for reverse-phase feedback)

STAGE

2, 4, 6, 8, 10, 12,

14, 16

Number of phase shift stages

LSH F 21.2 Hz–8.00 kHz Low shelving ﬁlter frequency

LSH G –12.0 to +12.0 dB Low shelving ﬁlter gain

HSH F 50.0 Hz–16.0 kHz High shelving ﬁlter frequency

HSH G –12.0 to +12.0 dB High shelving ﬁlter gain

Parameter Range Description

REV TIME 0.3–99.0 s Reverb time

INI. DLY 0.0–500.0 ms Initial delay before reverb begins

HI. RATIO 0.1–1.0 High-frequency reverb time ratio

DIFF. 0–10 Spread

DENSITY 0–100% Reverb density

HPF

THRU, 21.2 Hz–

8.00 kHz

High-pass ﬁlter cutoff frequency

LPF

50.0 Hz–16.0 kHz,

THRU

Low-pass ﬁlter cutoff frequency

REV/CHO 0–100%

Reverb and chorus balance (0% =

all reverb, 100% = all chorus)

FREQ. 0.05–40.00 Hz Modulation speed

AM DEPTH 0–100% Amplitude modulation depth

PM DEPTH 0–100% Pitch modulation depth

MOD. DLY 0.0–500.0 ms Modulation delay time

WAVE Sine, Tri Modulation waveform

SYNC OFF/ON Tempo parameter sync on/off

NOTE

*1.

Used in conjunction with TEMPO

to determine FREQ.

Parameter Range Description

REV TIME 0.3–99.0 s Reverb time

INI. DLY 0.0–500.0 ms Initial delay before reverb begins

HI. RATIO 0.1–1.0 High-frequency reverb time ratio

DIFF. 0–10 Spread

DENSITY 0–100% Reverb density

HPF

THRU, 21.2 Hz–

8.00 kHz

High-pass ﬁlter cutoff frequency

LPF

50.0 Hz–16.0 kHz,

THRU

Low-pass ﬁlter cutoff frequency

REV.BAL 0–100%

Reverb and chorused reverb bal-

ance (0% = all chorused reverb,

100% = all reverb)

FREQ. 0.05–40.00 Hz Modulation speed

AM DEPTH 0–100% Amplitude modulation depth

PM DEPTH 0–100% Pitch modulation depth

MOD. DLY 0.0–500.0 ms Modulation delay time

WAVE Sine, Tri Modulation waveform

SYNC OFF/ON Tempo parameter sync on/off

NOTE

*1.

Used in conjunction with TEMPO

to determine FREQ.

Effects Parameters

330 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

❏ REV+FLANGE

One input, two output reverb and flanger effects in

parallel.

❏ REV→FLANGE

One input, two output reverb and flanger effects in series.

❏ REV+SYMPHO.

One input, two output reverb and symphonic effects in

parallel.

❏ REV→SYMPHO.

One input, two output reverb and symphonic effects in

series.

Parameter Range Description

REV TIME 0.3–99.0 s Reverb time

INI. DLY 0.0–500.0 ms Initial delay before reverb begins

HI. RATIO 0.1–1.0 High-frequency reverb time ratio

DIFF. 0–10 Spread

DENSITY 0–100% Reverb density

HPF

THRU, 21.2 Hz–

8.00 kHz

High-pass ﬁlter cutoff frequency

LPF

50.0 Hz–16.0 kHz,

THRU

Low-pass ﬁlter cutoff frequency

REV/FLG 0–100%

Reverb and ﬂange balance (0% =

all reverb, 100% = all ﬂange)

FREQ. 0.05–40.00 Hz Modulation speed

DEPTH 0–100% Modulation depth

MOD. DLY 0.0–500.0 ms Modulation delay time

FB. GAIN –99 to +99%

Feedback gain (plus values for

normal-phase feedback, minus

values for reverse-phase feedback)

WAVE Sine, Tri Modulation waveform

SYNC OFF/ON Tempo parameter sync on/off

NOTE

*1.

Used in conjunction with TEMPO

to determine FREQ.

Parameter Range Description

REV TIME 0.3–99.0 s Reverb time

INI. DLY 0.0–500.0 ms Initial delay before reverb begins

HI. RATIO 0.1–1.0 High-frequency reverb time ratio

DIFF. 0–10 Spread

DENSITY 0–100% Reverb density

HPF

THRU, 21.2 Hz–

8.00 kHz

High-pass ﬁlter cutoff frequency

LPF

50.0 Hz–16.0 kHz,

THRU

Low-pass ﬁlter cutoff frequency

REV.BAL 0–100%

Reverb and ﬂanged reverb bal-

ance (0% = all ﬂanged reverb,

100% = all reverb)

FREQ. 0.05–40.00 Hz Modulation speed

DEPTH 0–100% Modulation depth

MOD. DLY 0.0–500.0 ms Modulation delay time

FB. GAIN –99 to +99%

Feedback gain (plus values for

normal-phase feedback, minus

values for reverse-phase feedback)

WAVE Sine, Tri Modulation waveform

SYNC OFF/ON Tempo parameter sync on/off

NOTE

*1.

Used in conjunction with TEMPO

to determine FREQ.

Parameter Range Description

REV TIME 0.3–99.0 s Reverb time

INI. DLY 0.0–500.0 ms Initial delay before reverb begins

HI. RATIO 0.1–1.0 High-frequency reverb time ratio

DIFF. 0–10 Spread

DENSITY 0–100% Reverb density

HPF

THRU, 21.2 Hz–

8.00 kHz

High-pass ﬁlter cutoff frequency

LPF

50.0 Hz–16.0 kHz,

THRU

Low-pass ﬁlter cutoff frequency

REV/SYM 0–100%

Reverb and symphonic balance

(0% = all reverb, 100% = all sym-

phonic)

FREQ. 0.05–40.00 Hz Modulation speed

DEPTH 0–100% Modulation depth

MOD. DLY 0.0–500.0 ms Modulation delay time

WAVE Sine, Tri Modulation waveform

SYNC OFF/ON Tempo parameter sync on/off

NOTE

*1.

Used in conjunction with TEMPO

to determine FREQ.

Parameter Range Description

REV TIME 0.3–99.0 s Reverb time

INI. DLY 0.0–500.0 ms Initial delay before reverb begins

HI. RATIO 0.1–1.0 High-frequency reverb time ratio

DIFF. 0–10 Spread

DENSITY 0–100% Reverb density

HPF

THRU, 21.2 Hz–

8.00 kHz

High-pass ﬁlter cutoff frequency

LPF

50.0 Hz–16.0 kHz,

THRU

Low-pass ﬁlter cutoff frequency

REV.BAL 0–100%

Reverb and symphonic reverb bal-

ance (0% = all symphonic reverb,

100% = all reverb)

FREQ. 0.05–40.00 Hz Modulation speed

DEPTH 0–100% Modulation depth

MOD. DLY 0.0–500.0 ms Modulation delay time

WAVE Sine, Tri Modulation waveform

SYNC OFF/ON Tempo parameter sync on/off

NOTE

*1.

Used in conjunction with TEMPO

to determine FREQ.

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 331

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

❏ REV→PAN

One input, two output reverb and autopan effects in

parallel.

❏ DELAY+ER.

One input, two output delay and early reflections effects in

parallel.

❏ DELAY→ER.

One input, two output delay and early reflections effects in

series.

❏ DELAY+REV

One input, two output delay and reverb effects in parallel.

Parameter Range Description

REV TIME 0.3–99.0 s Reverb time

INI. DLY 0.0–500.0 ms Initial delay before reverb begins

HI. RATIO 0.1–1.0 High-frequency reverb time ratio

DIFF. 0–10 Spread

DENSITY 0–100% Reverb density

HPF

THRU, 21.2 Hz–

8.00 kHz

High-pass ﬁlter cutoff frequency

LPF

50.0 Hz–16.0 kHz,

THRU

Low-pass ﬁlter cutoff frequency

REV.BAL 0–100%

Reverb and panned reverb bal-

ance (0% = all panned reverb,

100% = all reverb)

FREQ. 0.05–40.00 Hz Modulation speed

DEPTH 0–100% Modulation depth

DIR.

*1. L↔R, L→R, L←R, Turn L, Turn R

Panning direction

WAVE Sine, Tri, Square Modulation waveform

SYNC OFF/ON Tempo parameter sync on/off

NOTE

*2.

Used in conjunction with TEMPO

to determine FREQ.

Parameter Range Description

DELAY L 0.0–1000.0 ms Left channel delay time

DELAY R 0.0–1000.0 ms Right channel delay time

FB. DLY 0.0–1000.0 ms Feedback delay time

FB. GAIN –99 to +99%

Feedback gain (plus values for

normal-phase feedback, minus

values for reverse-phase feedback)

HI. RATIO 0.1–1.0 High-frequency feedback ratio

HPF

THRU, 21.2 Hz–

8.00 kHz

High-pass ﬁlter cutoff frequency

LPF

50.0 Hz–16.0 kHz,

THRU

Low-pass ﬁlter cutoff frequency

DLY/ER 0–100%

Delay and early reﬂections bal-

ance (0% = all delay, 100% = all

early reﬂections)

TYPE

S-Hall, L-Hall, Ran-

dom, Revers, Plate,

Spring

Type of early reﬂection simulation

ROOMSIZE 0.1–20.0 Reﬂection spacing

LIVENESS 0–10

Early reﬂections decay characteris-

tics (0 = dead, 10 = live)

INI. DLY 0.0–500.0 ms Initial delay before reverb begins

DIFF. 0–10 Spread

DENSITY 0–100% Reverb density

ER NUM. 1–19 Number of early reﬂections

SYNC OFF/ON Tempo parameter sync on/off

NOTE L

*1.

(Maximum value depends on the tempo setting)

Used in conjunction with TEMPO

to determine left channel DELAY L

NOTE R 1

Used in conjunction with TEMPO

to determine right channel DELAY

NOTE FB 1

Used in conjunction with TEMPO

to determine FB. DLY

Parameter Range Description

DELAY L 0.0–1000.0 ms Left channel delay time

DELAY R 0.0–1000.0 ms Right channel delay time

FB. DLY 0.0–1000.0 ms Feedback delay time

FB. GAIN –99 to +99%

Feedback gain (plus values for

normal-phase feedback, minus

values for reverse-phase feedback)

HI. RATIO 0.1–1.0 High-frequency feedback ratio

HPF

THRU, 21.2 Hz–

8.00 kHz

High-pass ﬁlter cutoff frequency

LPF

50.0 Hz–16.0 kHz,

THRU

Low-pass ﬁlter cutoff frequency

DLY.BAL 0–100%

Delay and early reﬂected delay

balance (0% = all early reﬂected

delay, 100% = all delay)

TYPE

S-Hall, L-Hall, Ran-

dom, Revers, Plate,

Spring

Type of early reﬂection simulation

ROOMSIZE 0.1–20.0 Reﬂection spacing

LIVENESS 0–10

Early reﬂections decay characteris-

tics (0 = dead, 10 = live)

INI. DLY 0.0–500.0 ms Initial delay before reverb begins

DIFF. 0–10 Spread

DENSITY 0–100% Reverb density

ER NUM. 1–19 Number of early reﬂections

SYNC OFF/ON Tempo parameter sync on/off

NOTE L

*1.

(Maximum value depends on the tempo setting)

Used in conjunction with TEMPO

to determine left channel DELAY L

NOTE R 1

Used in conjunction with TEMPO

to determine right channel DELAY

NOTE FB 1

Used in conjunction with TEMPO

to determine FB. DLY

Parameter Range Description

DELAY L 0.0–1000.0 ms Left channel delay time

DELAY R 0.0–1000.0 ms Right channel delay time

FB. DLY 0.0–1000.0 ms Feedback delay time

FB. GAIN –99 to +99%

Feedback gain (plus values for

normal-phase feedback, minus

values for reverse-phase feedback)

DELAY HI 0.1–1.0

Delay high-frequency feedback

ratio

HPF

THRU, 21.2 Hz–

8.00 kHz

High-pass ﬁlter cutoff frequency

LPF

50.0 Hz–16.0 kHz,

THRU

Low-pass ﬁlter cutoff frequency

DLY/REV 0–100%

Delay and reverb balance (0% =

all delay, 100% = all reverb)

REV TIME 0.3–99.0 s Reverb time

INI. DLY 0.0–500.0 ms Initial delay before reverb begins

REV HI 0.1–1.0 High-frequency reverb time ratio

DIFF. 0–10 Spread

DENSITY 0–100% Reverb density

SYNC OFF/ON Tempo parameter sync on/off

NOTE L

*1.

(Maximum value depends on the tempo setting)

Used in conjunction with TEMPO

to determine left channel DELAY L

NOTE R 1

Used in conjunction with TEMPO

to determine right channel DELAY

NOTE FB 1

Used in conjunction with TEMPO

to determine FB. DLY

Effects Parameters

332 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

❏ DELAY→REV

One input, two output delay and reverb effects in series.

❏ DIST→DELAY

One input, two output distortion and delay effects in

series.

❏ MULTI FILTER

Two input, two output 3-band multi-filter (24 dB/octave).

❏ FREEZE

One input, one output basic sampler.

Parameter Range Description

DELAY L 0.0–1000.0 ms Left channel delay time

DELAY R 0.0–1000.0 ms Right channel delay time

FB. DLY 0.0–1000.0 ms Feedback delay time

FB. GAIN –99 to +99%

Feedback gain (plus values for

normal-phase feedback, minus

values for reverse-phase feedback)

DELAY HI 0.1–1.0

Delay high-frequency feedback

ratio

HPF

THRU, 21.2 Hz–

8.00 kHz

High-pass ﬁlter cutoff frequency

LPF

50.0 Hz–16.0 kHz,

THRU

Low-pass ﬁlter cutoff frequency

DLY.BAL 0–100%

Delay and delayed reverb balance

(0% = all delayed reverb, 100% =

all delay)

REV TIME 0.3–99.0 s Reverb time

INI. DLY 0.0–500.0 ms Initial delay before reverb begins

REV HI 0.1–1.0 High-frequency reverb time ratio

DIFF. 0–10 Spread

DENSITY 0–100% Reverb density

SYNC OFF/ON Tempo parameter sync on/off

NOTE L

*1.

(Maximum value depends on the tempo setting)

Used in conjunction with TEMPO

to determine left channel DELAY L

NOTE R *1

Used in conjunction with TEMPO

to determine right channel DELAY

NOTE FB *1

Used in conjunction with TEMPO

to determine FB. DLY

Parameter Range Description

DST TYPE

DST1, DST2, OVD1,

OVD2, CRUNCH

Distortion type (DST = distortion,

OVD = overdrive)

DRIVE 0–100 Distortion drive

MASTER 0–100 Master volume

TONE –10 to +10 Tone control

N. GATE 0–20 Noise reduction

DELAY 0.0–2725.0 ms Delay time

FB. GAIN –99 to +99%

Feedback gain (plus values for

normal-phase feedback, minus

values for reverse-phase feed-

back)

HI. RATIO 0.1–1.0 High-frequency feedback ratio

FREQ. 0.05–40.00 Hz Modulation speed

DEPTH 0–100% Modulation depth

DLY.BAL 0–100%

Distortion and delay balance (0%

= all distortion, 100% = all

delayed distortion)

SYNC OFF/ON Tempo parameter sync on/off

DLY.NOTE

*1.

(Maximum value depends on the tempo setting)

Used in conjunction with TEMPO

to determine DELAY

MOD.NOT

*2.

Used in conjunction with TEMPO

to determine FREQ.

Parameter Range Description

TYPE 1 HPF, LPF, BPF

Filter 1 type: high pass, low pass,

band pass

TYPE 2 HPF, LPF, BPF

Filter 2 type: high pass, low pass,

band pass

TYPE 3 HPF, LPF, BPF

Filter 3 type: high pass, low pass,

band pass

FREQ. 1 28.0 Hz–16.0 kHz Filter 1 frequency

FREQ. 2 28.0 Hz–16.0 kHz Filter 2 frequency

FREQ. 3 28.0 Hz–16.0 kHz Filter 3 frequency

LEVEL 1 0–100 Filter 1 level

LEVEL 2 0–100 Filter 2 level

LEVEL 3 0–100 Filter 3 level

RESO. 1 0–20 Filter 1 resonance

RESO. 2 0–20 Filter 2 resonance

RESO. 3 0–20 Filter 3 resonance

Parameter Range Description

REC MODE MANUAL, INPUT

In MANUAL mode, recording is

started by pressing the REC and

PLAY buttons. In INPUT mode,

Record-Ready mode is engaged by

pressing the REC button, and

actual recording is triggered by the

input signal.

REC DLY

–1000 to +1000

Recording delay. For plus values,

recording starts after the trigger is

received. For minus values, record-

ing starts before the trigger is

received.

TRG LVL –60 to 0 dB

Input trigger level (i.e., the signal

level required to trigger recording

or playback)

TRG MASK 0–1000 ms

Once playback has been triggered,

subsequent triggers are ignored for

the duration of the TRG MASK

time.

PLY MODE

MOMENT,

CONTI., INPUT

In MOMENT mode, the sample

plays only while the that the PLAY

button is pressed. In CONT mode,

playback continues once the PLAY

button has been pressed. The

number of times the sample plays

is set using the LOOP NUM param-

eter. In INPUT mode, playback is

triggered by the input signal.

START

*1. 0.0–5941.0 ms (fs=44.1 kHz), 0.0 ms–5458.3 ms (fs=48 kHz), 0.0–

2970.5 ms (fs=88.2 kHz), 0.0 ms–2729.2 ms (fs=96 kHz)

Playback start point in milliseconds

END 1 Playback end point in milliseconds

LOOP 1 Loop start point in milliseconds

LOOP

NUM

0–100 Number of times the sample plays

START

[SAMPLE]

0–262000 Playback start point in samples

END

[SAMPLE]

0–262000 Playback end point in samples

LOOP

[SAMPLE]

0–262000 Loop start point in samples

PITCH

–12 to +12 semi-

tones

Playback pitch shift

FINE –50 to +50 cents Playback pitch shift ﬁne

MIDI TRG OFF, C1–C6, ALL

PLAY button can be triggered by

using MIDI Note on/off messages.

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 333

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

❏ ST REVERB

Two input, two output stereo reverb.

❏ M. BAND DYNA.

Two input, two output 3-band dynamics processor, with

individual solo and gain reduction metering for each band.

❏ M.BAND COMP

Two input, two output 3-band compressor, with individ-

ual solo and gain reduction metering for each band.

❏ REV-X HALL, REV-X ROOM, REV-X PLATE

Newly-developed two input, two output reverb algo-

rithm. Delivers dense and rich reverberation, smooth

decay, and provides a spaciousness and depth that

enhances the original sound. Choose from three types

depending on your location and needs; REV-X HALL,

REV-X ROOM, and REV-X PLATE.

Parameter Range Description

REV TIME 0.3–99.0 s Reverb time

REV TYPE

Hall, Room, Stage,

Plate

Reverb type

INI. DLY 0.0–100.0 ms Initial delay before reverb begins

HI. RATIO 0.1–1.0 High-frequency reverb time ratio

LO. RATIO 0.1–2.4 Low-frequency reverb time ratio

DIFF. 0–10

Reverb diffusion (left–right reverb

spread)

DENSITY 0–100% Reverb density

E/R BAL. 0–100%

Balance of early reﬂections and

reverb (0% = all reverb, 100% =

all early reﬂections)

HPF

THRU, 21.2 Hz–

8.00 kHz

High-pass ﬁlter cutoff frequency

LPF

50.0 Hz–16.0 kHz,

THRU

Low-pass ﬁlter cutoff frequency

Parameter Range Description

LOW GAIN –96.0 to +12.0 dB Low band level

MID GAIN –96.0 to +12.0 dB Mid band level

HI. GAIN –96.0 to +12.0 dB High band level

PRESENCE –10 to +10

For positive values, the thresh-

old of the high band is low-

ered and the threshold of the

low band is increased. For

negative values, the opposite

will occur. When set to 0, all

three bands are affected the

same.

CMP. THRE –24.0 dB to 0.0 dB Compressor threshold

CMP. RAT 1:1 to 20:1 Compressor ratio

CMP. ATK 0–120 ms Compressor attack

CMP. REL 1 Compressor release time

CMP. KNEE 0–5 Compressor knee

LOOKUP 0.0–100.0 ms Lookup delay

CMP. BYP ON/OFF Compressor bypass

L–M XOVR 21.2 Hz–8.00 kHz Low/mid crossover frequency

M–H XOVR 21.2 Hz–8.00 kHz Mid/high crossover frequency

SLOPE –6 dB, –12 dB Filter slope

CEILING –6.0 dB to 0.0 dB, OFF

Speciﬁes the maximum output

level

EXP. THRE –54.0 dB to –24.0 dB Expander threshold

EXP. RAT 1:1 to ∞:1 Expander ratio

EXP. REL

*1. 6.0 ms–46.0 s (fs=44.1 kHz), 5.0 ms–42.3 s (fs=48 kHz),

3 ms–23.0 s (fs=88.2 kHz), 3 ms–21.1 s (fs=96 kHz)

Expander release time

EXP. BYP ON/OFF Expander bypass

LIM. THRE –12.0 dB to 0.0 dB Limiter threshold

LIM. ATK 0–120 ms Limiter attack

LIM. REL 1 Limiter release time

LIM. BYP ON/OFF Limiter bypass

LIM. KNEE 0–5 Limiter knee

Parameter Range Description

LOW GAIN –96.0 to +12.0 dB Low band level

MID GAIN –96.0 to +12.0 dB Mid band level

HI. GAIN –96.0 to +12.0 dB High band level

L-M XOVR 21.2 Hz–8.00 kHz Low/mid crossover frequency

M-H XOVR 21.2 Hz–8.00 kHz Mid/high crossover frequency

SLOPE –6 dB, –12 dB Filter slope

CEILING –6.0 dB to 0.0 dB, OFF

Speciﬁes the maximum output

level

LOOKUP 0.0–100.0 ms Lookup delay

LOW THRE –54.0 dB to 0.0 dB Low band threshold level

MID THRE –54.0 dB to 0.0 dB Mid band threshold level

HI. THRE –54.0 dB to 0.0 dB High band threshold level

RATIO 1:1 to 20:1 Compression ratio

ATTACK 0–120 ms Compressor attack time

CMP. REL

*1. 6.0 ms–46.0 s (fs=44.1 kHz), 5.0 ms–42.3 s (fs=48 kHz),

3 ms–23.0 s (fs=88.2 kHz), 3 ms–21.1 s (fs=96 kHz)

Compressor release time

KNEE 0–5 Compressor knee

BYPASS ON/OFF Bypasses the compressor

Parameter Range Description

REV TIME

0.47–46.92 s

*1. These values are for when the effect type is REV-X HALL and the

ROOM SIZE=28. The range will differ depending on the effect type

and ROOM SIZE setting.

Reverb time

INI. DLY 0.0–120.0 ms Initial delay before reverb begins

HI. RATIO 0.1–1.0 High-frequency reverb time ratio

LO. RATIO 0.1–2.4 Low-frequency reverb time ratio

LO.FREQ 22.0 Hz–18.0 kHz

Frequency point for LO.RATIO

setting

DIFF. 0–10

Reverb diffusion (left–right reverb

spread)

ROOM

SIZE

0–28

Size of room

DECAY 0–53 Gate closing speed

HPF

THRU, 22.0 Hz–

8.00 kHz

High-pass ﬁlter cutoff frequency

LPF

1.00 kHz–18.0 kHz,

THRU

Low-pass ﬁlter cutoff frequency

Effects Parameters

334 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

❏ COMP276

This effect emulates the characteristics of analog compres-

sors that are widely used in recording studios. It will

produce a thick, strong frame sound suitable for drums

and bass. You can control two monaural channels

independently.

❏ COMP276S

This effect emulates the characteristics of analog compres-

sors that are widely used in recording studios. It produces a

thick, strong frame sound suitable for drums and bass. You

can link and control the L and R channel parameters.

❏ COMP260

This effect emulates the characteristics of mid 70’s com-

pressors/limiters that are the standard for live SR. You can

control two monaural channels independently. You can

also link several parameters via stereo links.

❏ COMP260S

This effect emulates the characteristics of mid 70’s com-

pressors/limiters that are the standard for live SR. You can

link and control the L and R channel parameters.

Parameter Range Description

INPUT 1 –180.0 to 0 dB Adjusts the CH1 input level

OUTPUT 1 –180.0 to 0 dB Adjusts the CH1 output gain

RATIO 1

2:1, 4:1, 8:1, 12:1,

20:1

Ratio for CH1 compressor

ATTACK 1 0.022–50.4 ms Attack time for CH1 compressor

RELEASE1 10.88–544.22 ms Release time for CH1 compressor

MAKE UP1 OFF, ON

Automatically corrects output

gain reduction when CH1 com-

pressor is applied

SIDEHPF1 OFF, ON

When the HPF in the side chain of

the CH1 compressor is turned on,

the compression applied to the

low range will be weakened, thus

emphasizing the low range.

INPUT 2 –180.0 to 0 dB Adjusts the CH2 input level

OUTPUT 2 –180.0 to 0 dB Adjusts the CH2 output gain

RATIO 2

2:1, 4:1, 8:1, 12:1,

20:1

Ratio of CH2 compressor

ATTACK 2 0.022–50.40 ms Attack time of CH2 compressor

RELEASE2 10.88–544.22 ms Release time of CH2 compressor

MAKE UP2 OFF, ON

Automatically corrects output

gain reduction when the CH2

compressor is applied

SIDEHPF2 OFF, ON

When the HPF in the side chain of

the CH2 compressor is turned on,

the compression applied to the

low range will be weakened, thus

emphasizing the low range.

Parameter Range Description

INPUT –180.0 to 0 dB Adjusts the input level

OUTPUT –180.0 to 0 dB Adjusts the output gain

RATIO

1:2, 4:1, 8:1, 12:1,

20:1

Ratio of the compressor

ATTACK 0.022–50.40 ms Attack time of the compressor

RELEASE 10.88–544.22 ms Release time of the compressor

MAKE UP OFF, ON

Automatically corrects output

gain reduction when the com-

pressor is applied

SIDE HPF OFF, ON

When the HPF in the side chain of

the compressor is turned on, the

compression applied to the low

range will be weakened, thus

emphasizing the low range.

Parameter Range Description

THRE.1 –60.0 to 0.0 dB Threshold of CH1 compressor

KNEE1

SOFT, MEDIUM,

HARD

Knee of CH1 compressor

ATTACK1 0.010–80.0 ms Attack time of CH1 compressor

RELEASE1 6.2–999.0 ms Release time of CH1 compressor

RATIO1 1.00–500, ∞ Ratio of CH1 compressor

OUTPUT1 –20.0 to 40.0 dB Adjusts the CH1 output gain

THRE.2 –60.0 to 0.0 dB Threshold of CH2 compressor

KNEE2

SOFT, MEDIUM,

HARD

Knee of CH2 compressor

ATTACK2 0.010–80.0 ms Attack time of CH2 compressor

RELEASE2 6.2–999.0 ms Release time of CH2 compressor

RATIO2

1.00–500,

∞

Ratio of CH2 compressor

OUTPUT2 –20.0 to 40.0 dB Adjusts the CH2 output gain

ST LINK OFF, ON

Links CH1 and CH2 as a stereo

pair. THRE., KNEE, ATTACK,

RELEASE, and RATIO parameters

are linked; OUTPUT parameter is

not linked

Parameter Range Description

THRE. –60.0 to 0.0 dB Threshold of the compressor

KNEE

SOFT, MEDIUM,

HARD

Knee of the compressor

ATTACK 0.010–80.0 ms Attack time of the compressor

RELEASE 6.2–999.0 ms Release time of the compressor

RATIO 1.00–500, ∞ Ratio of the compressor

OUTPUT –20.0 to 40.0 dB Adjusts the output gain

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 335

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

❏ EQUALIZER601

This effect emulates the characteristics of 70’s analog

equalizers. Re-creating the distortion of typical analog cir-

cuits will add drive to the sound.

❏ OPENDECK

It emulates the tape compression created by two open reel

tape recorders (a recording deck and a playback deck.) You

can change the sound quality by adjusting various ele-

ments, such as the deck type, tape quality, playback speed,

etc.

❏ DE-ESSER

This detects and compresses only the high-frequency con-

sonantal components (e.g., sibilants) of a vocal sound. Two

monaural channels can be controlled independently.

Parameter Range Description

LO TYPE HPF-2/1, LSH-1/2 Type of EQ1

LO F 16.0 Hz to 20.0 kHz Cut-off frequency of EQ1

LO G –18.0 to +18.0 dB Gain of EQ1

MID1 Q 0.50–16.00 Q of EQ2

MID1 F 16.0 Hz to 20.0 kHz Center frequency of EQ2

MID1 G –18.0 to +18.0 dB Gain of EQ2

MID2 Q 0.50–16.00 Q of EQ3

MID2 F 16.0 Hz to 20.0 kHz Center frequency of EQ3

MID2 G –18.0 to +18.0 dB Gain of EQ3

INPUT –18.0 to +18.0 dB Input gain

OUTPUT –18.0 to +18.0 dB Output gain

MID3 Q 0.50–16.00 Q of EQ4

MID3 F 16.0 Hz to 20.0 kHz Center frequency of EQ4

MID3 G –18.0 to +18.0 dB Gain of EQ4

MID4 Q 0.50–16.00 Q of EQ5

MID4 F 16.0 Hz to 20.0 kHz Center frequency of EQ5

MID4 G –18.0 to +18.0 dB Gain of EQ5

HI TYPE LPF-2/1, HSH-1/2 Type of EQ6

HI F

16.0 Hz to 20.0 kHz

*1. 16.0 Hz to 20.0 kHz (LPF-1, LPF-2), 1.0 kHz to 20.0 kHz (HSH-1,

HSH-2)

Cut-off frequency of EQ6

HI G –18.0 to +18.0 dB Gain of EQ6

LO SW OFF, ON Switches EQ1 on/off

MID1 SW OFF, ON Switches EQ2 on/off

MID2 SW OFF, ON Switches EQ3 on/off

MID3 SW OFF, ON Switches EQ4 on/off

MID4 SW OFF, ON Switches EQ5 on/off

HI SW OFF, ON Switches EQ6 on/off

TYPE CLEAN, DRIVE

Selects the equalizer type. The

CLEAN equalizer provides

non-distorted, clear, typical

digital sound, emulating varia-

tions in frequency response in

the analog circuits. The DRIVE

equalizer provides distorted,

driven sound that enhances

analog ﬂavor, emulating

changes in frequency

response in the analog cir-

cuits.

Parameter Range Description

REC DEC

Swss70, Swss78,

Swss85, Amer70

Selects the recording deck type

REC LVL –96.0 to +18.0 dB

Adjusts the input level of the

recording deck. As you raise the

level, tape compression is gener-

ated, which narrows the dynamic

range and distorts the sound

REC HI –6.0 to +6.0 dB

Adjusts the high range gain of the

recording deck

REC BIAS –1.00 to +1.00

Adjusts the bias of the recording

deck

REPR DEC

Swss70, Swss78,

Swss85, Amer70

Selects the playback deck type

REPR LVL –96.0 to +18.0 dB

Adjusts the output level of the

playback deck

REPR HI –6.0 to +6.0 dB

Adjusts the high range gain of the

playback deck

REPR LO –6.0 to +6.0 dB

Adjusts the low range gain of the

playback deck

MAKE UP Off, On

When you adjust the REC LVL, the

REPR LVL reﬂects the change,

maintaining the relative output

level. You can change the amount

of distortion without changing

the output level.

TP SPEED 15ips, 30ips Selects the tape speed

TP KIND Old, New Selects the tape type

Parameter Range Description

THRE. 1

–54.0 to 0.0 dB

(541 points)

Threshold level above which the

CH1 de-esser effect will apply.

FREQ. 1

1.00 kHz to 12.5 kHz

(45 points)

Cutoff frequency of the HPF

used to detect the high frequen-

cies for CH1.

THRE. 2

–54.0 to 0.0 dB

(541 points)

Threshold level above which the

CH2 de-esser effect will apply.

FREQ. 2

1.00 kHz to 12.5 kHz

(45 points)

Cutoff frequency of the HPF

used to detect the high frequen-

cies for CH2.

Effects Parameters

336 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

Some of the PM5D’s effects allow you to synchronize the effect with the tempo. There are two such types of effect; delay-type

effects and modulation-type effects. For delay-type effects, the delay time will change according to the tempo. For modula-

tion-type effects, the frequency of the modulation signal will change according to the tempo.

• Parameters related to tempo synchronization

The following ﬁve parameters are related to tempo synchronization.

1) SYNC 2) NOTE 3) TEMPO 4) DELAY 5) FREQ.

SYNC:.............................This is the on/off switch for tempo synchronization.

NOTE and TEMPO: .....These are the basic parameters for tempo synchronization.

DELAY and FREQ.:.......DELAY is the delay time, and FREQ. is the frequency of the modulation signal. These directly affect the

way in which the effect sound will change. DELAY is relevant only for delay-type effects, and FREQ. is

relevant only for modulation-type effects.

• How the parameters are related

Te mpo synchronization calculates the DELAY (or FREQ.) value*a from the TEMPO and NOTE.

If you turn SYNC on

If you edit NOTE → DELAY (or FREQ.) will be set

In this case, the DELAY (or FREQ.) value is calculated as follows.

DELAY (or FREQ.) = NOTE x 4 x (60/TEMPO)

If you edit TEMPO → DELAY (or FREQ.) will be set

In this case, the DELAY (or FREQ.) value is calculated as follows.

DELAY = NOTE x 4 x (60 / TEMPO) sec

FREQ. = (TEMPO / 60) / (NOTE x 4) Hz

Example 1: When SYNC=ON, DELAY=250 ms, TEMPO=120, you change NOTE from 8th note to quarter note

DELAY= new NOTE x 4 x (60/TEMPO)

= (1/4) x 4 x (60/120)

= 0.5 (sec)

= 500 ms

Thus, the DELAY will change from 250 ms to 500 ms.

Example 2: When SYNC=ON, DELAY=250 ms, NOTE=8th note, you change TEMPO from 120 to 121

DELAY = NOTE x 4 x (60 / new TEMPO)

= (1 / 8) x 4 x (60 / 121)

= 0.2479(sec)

= 247.9 (ms)

Thus, the TEMPO will change from 250 ms to 247.9 ms.

*a Rounded values are used for the calculation results.

• Special characteristics of the TEMPO parameter

The TEMPO parameter has the following characteristics that are unlike other parameters.

•It is a common value shared by all effects

•You cannot stored it to or recall it from the Effects Library. (You can store it to and recall it from a Scene.)

This means that the TEMPO value may not necessarily be the same when an effect is recalled as when that effect was stored. Here is

an example.

Store the effect: TEMPO=120 → Change TEMPO to 60 → Recall the effect: TEMPO=60

Normally when you change the TEMPO, the DELAY (or FREQ.) will be re-set accordingly. However if the DELAY (or FREQ.) were

changed, the effect would sound differently when recalled than when it was stored. To prevent the effect from changing in this way

between store and recall, the PM5D does not update the DELAY (or FREQ.) value when an effect is recalled, even if the TEMPO is

no longer the same as when that effect was stored.

* The NOTE parameter is calculated based on the following values.

Effects and tempo synchronization

= 1/48

= 2/1

= 1/16= 1/24 = 1/12

= 3/4= 3/16 = 1/2

= 3/32 = 1/6

= 1/4

= 1/8

= 1/1= 3/8

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 337

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

Scene Memory/Effect Library to Program Change Table

❏ Preset Bank/Ch# 1 ❏ Preset Bank/Ch# 2

Program

Change#

Scene/

Effect

Preset#

Program

Change#

Scene/

Effect

Preset#

001

Scene

001 065

Scene

065

002 002 066 066

003 003 067 067

004 004 068 068

005 005 069 069

006 006 070 070

007 007 071 071

008 008 072 072

009 009 073 073

010 010 074 074

011 011 075 075

012 012 076 076

013 013 077 077

014 014 078 078

015 015 079 079

016 016 080 080

017 017 081 081

018 018 082 082

019 019 083 083

020 020 084 084

021 021 085 085

022 022 086 086

023 023 087 087

024 024 088 088

025 025 089 089

026 026 090 090

027 027 091 091

028 028 092 092

029 029 093 093

030 030 094 094

031 031 095 095

032 032 096 096

033 033 097 097

034 034 098 098

035 035 099 099

036 036 100 100

037 037 101 101

038 038 102 102

039 039 103 103

040 040 104 104

041 041 105 105

042 042 106 106

043 043 107 107

044 044 108 108

045 045 109 109

046 046 110 110

047 047 111 111

048 048 112 112

049 049 113 113

050 050 114 114

051 051 115 115

052 052 116 116

053 053 117 117

054 054 118 118

055 055 119 119

056 056 120 120

057 057 121 121

058 058 122 122

059 059 123 123

060 060 124 124

061 061 125 125

062 062 126 126

063 063 127 127

064 064 128 128

Program

Change#

Scene/

Effect

Preset#

Program

Change#

Scene/

Effect

Preset#

001

Scene

129 065

Scene

193

002 130 066 194

003 131 067 195

004 132 068 196

005 133 069 197

006 134 070 198

007 135 071 199

008 136 072 200

009 137 073 201

010 138 074 202

011 139 075 203

012 140 076 204

013 141 077 205

014 142 078 206

015 143 079 207

016 144 080 208

017 145 081 209

018 146 082 210

019 147 083 211

020 148 084 212

021 149 085 213

022 150 086 214

023 151 087 215

024 152 088 216

025 153 089 217

026 154 090 218

027 155 091 219

028 156 092 220

029 157 093 221

030 158 094 222

031 159 095 223

032 160 096 224

033 161 097 225

034 162 098 226

035 163 099 227

036 164 100 228

037 165 101 229

038 166 102 230

039 167 103 231

040 168 104 232

041 169 105 233

042 170 106 234

043 171 107 235

044 172 108 236

045 173 109 237

046 174 110 238

047 175 111 239

048 176 112 240

049 177 113 241

050 178 114 242

051 179 115 243

052 180 116 244

053 181 117 245

054 182 118 246

055 183 119 247

056 184 120 248

057 185 121 249

058 186 122 250

059 187 123 251

060 188 124 252

061 189 125 253

062 190 126 254

063 191 127 255

064 192 128 256

Scene Memory/Effect Library to Program Change Table

338 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

❏ Preset Bank/Ch# 3 ❏ Preset Bank/Ch# 4

Program

Change#

Scene/

Effect

Preset#

Program

Change#

Scene/

Effect

Preset#

001

Scene

257 065

Scene

321

002 258 066 322

003 259 067 323

004 260 068 324

005 261 069 325

006 262 070 326

007 263 071 327

008 264 072 328

009 265 073 329

010 266 074 330

011 267 075 331

012 268 076 332

013 269 077 333

014 270 078 334

015 271 079 335

016 272 080 336

017 273 081 337

018 274 082 338

019 275 083 339

020 276 084 340

021 277 085 341

022 278 086 342

023 279 087 343

024 280 088 344

025 281 089 345

026 282 090 346

027 283 091 347

028 284 092 348

029 285 093 349

030 286 094 350

031 287 095 351

032 288 096 352

033 289 097 353

034 290 098 354

035 291 099 355

036 292 100 356

037 293 101 357

038 294 102 358

039 295 103 359

040 296 104 360

041 297 105 361

042 298 106 362

043 299 107 363

044 300 108 364

045 301 109 365

046 302 110 366

047 303 111 367

048 304 112 368

049 305 113 369

050 306 114 370

051 307 115 371

052 308 116 372

053 309 117 373

054 310 118 374

055 311 119 375

056 312 120 376

057 313 121 377

058 314 122 378

059 315 123 379

060 316 124 380

061 317 125 381

062 318 126 382

063 319 127 383

064 320 128 384

Program

Change#

Scene/

Effect

Preset#

Program

Change#

Scene/

Effect

Preset#

001

Scene

385 065

Scene

449

002 386 066 450

003 387 067 451

004 388 068 452

005 389 069 453

006 390 070 454

007 391 071 455

008 392 072 456

009 393 073 457

010 394 074 458

011 395 075 459

012 396 076 460

013 397 077 461

014 398 078 462

015 399 079 463

016 400 080 464

017 401 081 465

018 402 082 466

019 403 083 467

020 404 084 468

021 405 085 469

022 406 086 470

023 407 087 471

024 408 088 472

025 409 089 473

026 410 090 474

027 411 091 475

028 412 092 476

029 413 093 477

030 414 094 478

031 415 095 479

032 416 096 480

033 417 097 481

034 418 098 482

035 419 099 483

036 420 100 484

037 421 101 485

038 422 102 486

039 423 103 487

040 424 104 488

041 425 105 489

042 426 106 490

043 427 107 491

044 428 108 492

045 429 109 493

046 430 110 494

047 431 111 495

048 432 112 496

049 433 113 497

050 434 114 498

051 435 115 499

052 436 116 500

053 437 117 000

054 438 118

No Assign

055 439 119

056 440 120

057 441 121

058 442 122

059 443 123

060 444 124

061 445 125

062 446 126

063 447 127

064 448 128

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 339

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

❏ Preset Bank/Ch# 5

❏ Preset Bank/Ch# 6

❏ Preset Bank/Ch# 7

❏ Preset Bank/Ch# 8

❏ Preset Bank/Ch# 9

❏ Preset Bank/Ch# 10

❏ Preset Bank/Ch# 11

❏ Preset Bank/Ch# 12

❏ Preset Bank/Ch# 13

❏ Preset Bank/Ch# 14

❏ Preset Bank/Ch# 15

❏ Preset Bank/Ch# 16

Program Change# Scene/Effect Preset#

001

No Assign

002

003

128

Program Change# Scene/Effect Preset#

001

No Assign

002

003

128

Program Change# Scene/Effect Preset#

001

No Assign

002

003

128

Program Change# Scene/Effect Preset#

001

No Assign

002

003

128

Program Change# Scene/Effect Preset#

001

Effect1

001

002 002

003 003

128 128

Program Change# Scene/Effect Preset#

001

Effect2

001

002 002

003 003

128 128

Program Change# Scene/Effect Preset#

001

Effect3

001

002 002

003 003

128 128

Program Change# Scene/Effect Preset#

001

Effect4

001

002 002

003 003

128 128

Program Change# Scene/Effect Preset#

001

Effect5

001

002 002

003 003

128 128

Program Change# Scene/Effect Preset#

001

Effect6

001

002 002

003 003

128 128

Program Change# Scene/Effect Preset#

001

Effect7

001

002 002

003 003

128 128

Program Change# Scene/Effect Preset#

001

Effect8

001

002 002

003 003

128 128

Scene Memory/Effect Library to Program Change Table

340 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

❏ Bank/Ch# _

Program

Change#

Scene/

Effect

User#

Program

Change#

Scene/

Effect

User#

Program

Change#

Scene/

Effect

User#

001 044 087

002 045 088

003 046 089

004 047 090

005 048 091

006 049 092

007 050 093

008 051 094

009 052 095

010 053 096

011 054 097

012 055 098

013 056 099

014 057 100

015 058 101

016 059 102

017 060 103

018 061 104

019 062 105

020 063 106

021 064 107

022 065 108

023 066 109

024 067 110

025 068 111

026 069 112

027 070 113

028 071 114

029 072 115

030 073 116

031 074 117

032 075 118

033 076 119

034 077 120

035 078 121

036 079 122

037 080 123

038 081 124

039 082 125

040 083 126

041 084 127

042 085 128

043 086

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 341

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

Parameters that can be assigned to control changes

MODE PARAMETER 1 PARAMETER 2

NO ASSIGN — —

FADER H

INPUT

CH 1–CH48

STIN1L–STIN4R

FXRTN1L–FXRTN4R

OUTPUT

MIX 1–MIX24

MATRIX 1–MATRIX 8

STEREO AL–STEREO BR

FADER L

INPUT

CH 1–CH48

STIN1L–STIN4R

FXRTN1L–FXRTN4R

OUTPUT

MIX 1–MIX24

MATRIX 1–MATRIX 8

STEREO AL–STEREO BR

CH ON

INPUT

CH 1–CH48

STIN1L–STIN4R

FXRTN1L–FXRTN4R

OUTPUT

MIX 1–MIX24

MATRIX 1–MATRIX 8

STEREO AL–STEREO BR

PHASE INPUT

CH 1–CH48

STIN1L–STIN4R

FXRTN1L–FXRTN4R

INSERT

INPUT

CH 1–CH48

STIN1L–STIN4R

OUTPUT

MIX 1–MIX24

MATRIX 1–MATRIX 8

STEREO AL–STEREO BR

DIRECT OUT ON

CH 1–CH48

STIN1L–STIN4R

FXRTN1L–FXRTN4R

PAN/BALANCE INPUT

CH 1–CH48

STIN1L–STIN4R

FXRTN1L–FXRTN4R

BALANCE OUTPUT

MIX 1–MIX24

MATRIX 1–MATRIX 8

STEREO AL–STEREO BR

TO STEREO ON

CH 1–CH48

STIN1L–STIN4R

FXRTN1L–FXRTN4R

LCR

ON CH 1–CH48

STIN1L–STIN4R

FXRTN1L–FXRTN4R

MIX 1–MIX24

CSR

MIX SEND

PRE POINT

CH 1–CH48

STIN1L–STIN4R

FXRTN1L–FXRTN4R

MIX 1 ON–

MIX24 ON

MIX 1 PRE/POST–

MIX24 PRE/POST

MIX 1 LEVEL H–

MIX24 LEVEL H

MIX 1 LEVEL L–

MIX24 LEVEL L

MIX 1/ 2 PAN–

MIX23/24 PAN

FOLLOW PAN VARI

FOLLOW PAN FIXED

POST POINT MIX 1–MIX24

MIX TO STEREO

POINT

MIX 1–MIX24ON

PAN

MIX TO MATRIX

MATRIX 1 POINT–

MATRIX 8 POINT

MIX 1–MIX24

MATRIX 1 ON–

MATRIX 8 ON

MATRIX 1 LEVEL H–

MATRIX 8 LEVEL H

MATRIX 1 LEVEL L–

MATRIX 8 LEVEL L

MATRIX 1/2 PAN–

MATRIX 7/8 PAN

ST TO MATRIX

MATRIX 1 POINT–

MATRIX 8 POINT

STEREO AL–STEREO BR

MATRIX 1 ON–

MATRIX 8 ON

MATRIX 1 LEVEL H–

MATRIX 8 LEVEL H

MATRIX 1 LEVEL L–

MATRIX 8 LEVEL L

MATRIX 1/2 PAN–

MATRIX 7/8 PAN

IN DELAY

CH 1–CH48

STIN1L–STIN4R

TIME HIGH

TIME MID

TIME LOW

OUT DELAY

MIX 1–MIX24

MATRIX 1–MATRIX 8

STEREO AL–STEREO BR

TIME HIGH

TIME MID

TIME LOW

INPUT EQ

CH 1–CH48

STIN1L–STIN4R

FXRTN1L–FXRTN4R

LOW Q

LOW FREQ

LOW GAIN

LOW MID Q

LOW MID FREQ

LOW MID GAIN

HIGH MID Q

HIGH MID FREQ

HIGH MID GAIN

HIGH Q

HIGH FREQ

HIGH GAIN

LPF ON

LOW TYPE

HIGH TYPE

INPUT ATT INPUT

CH 1–CH48

STIN1L–STIN4R

FXRTN1L–FXRTN4R

INPUT HPF

ON CH 1–CH48

STIN1L–STIN4R

FXRTN1L–FXRTN4R

FREQ

MODE PARAMETER 1 PARAMETER 2

Parameters that can be assigned to control changes

342 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

OUTPUT EQ

MIX 1–MIX24

MATRIX 1–MATRIX 8

STEREO AL–STEREO BR

GEQ1–GEQ20

L LOW BYPASS

L LOW Q

L LOW FREQ

L LOW GAIN

L LOW MID BYPASS

L LOW MID Q

L LOW MID FREQ

L LOW MID GAIN

L HIGH MID BYPASS

L HIGH MID Q

L HIGH MID FREQ

L HIGH MID GAIN

L HIGH BYPASS

L HIGH Q

L HIGH FREQ

L HIGH GAIN

U LOW BYPASS

MIX 1–MIX24

STEREO AL–STEREO BR

GEQ1–GEQ20

U LOW Q

U LOW FREQ

U LOW GAIN

U LOW MID BYPASS

U LOW MID Q

U LOW MID FREQ

U LOW MID GAIN

U HIGH MID BYPASS

U HIGH MID Q

U HIGH MID FREQ

U HIGH MID GAIN

U HIGH BYPASS

U HIGH Q

U HIGH FREQ

U HIGH GAIN

L LOW TYPE MIX 1–MIX24

MATRIX 1–MATRIX 8

STEREO AL–STEREO BR

GEQ1–GEQ20

L HIGH TYPE

U LOW TYPE MIX 1–MIX24

STEREO AL–STEREO BR

GEQ1–GEQ20

U HIGH TYPE

L LOW HPF ON MIX 1–MIX24

MATRIX 1–MATRIX 8

STEREO AL–STEREO BR

GEQ1–GEQ20

L HIGH HPF ON

U LOW HPF ON MIX 1–MIX24

STEREO AL–STEREO BR

GEQ1–GEQ20

U HIGH HPF ON

INPUT GATE

CH 1–CH48

STIN1L–STIN4R

ATTACK

THRESHOLD

RANGE

HOLD H

HOLD L

DECAY H

DECAY L

INPUT COMP

CH 1–CH48

STIN1L–STIN4R

ATTACK

THRESHOLD

RELEASE H

RELEASE L

RATIO

GAIN

KNEE/WIDTH

MODE PARAMETER 1 PARAMETER 2

OUTPUT COMP

MIX 1–MIX24

MATRIX 1–MATRIX 8

STEREO AL–STEREO BR

ATTACK

THRESHOLD

RELEASE H

RELEASE L

RATIO

GAIN

KNEE/WIDTH

SURROUND

LFE H

CH 1–CH48

STIN1L–STIN4R

FXRTN1L–FXRTN4R

LFE L

DIVERGENCE F

DIVERGENCE R

LEFT-RIGHT PAN CH 1–CH48

STIN1L–STIN4R

FXRTN1L–FXRTN4R

ALT SEL CH

FRONT-REAR PAN

EFFECT

BYPASS

EFFECT 1–EFFECT 8

MIX BALANCE

PARAM 1 H–

PARAM32 L

GEQ

GEQ 1–GEQ20

GAIN 1–GAIN31

DCA

DCA 1–DCA 8FADER H

FADER L

MUTE MASTER ON MASTER 1–MASTER 8

RECALL SAFE ON

CH 1–CH48

STIN1L–STIN4R

FXRTN1L–FXRTN4R

MIX 1–MIX24

MATRIX 1–MATRIX 8

STEREO AL–STEREO BR

EFFECT 1–EFFECT 8

GEQ 1–GEQ 20

DCA 1–DCA 8

MUTE MASTER

CUE DELAY

TIME HIGH

TIME MID

TIME LOW

MONITOR

DELAY

TIME HIGH

TIME MID

TIME LOW

MODE PARAMETER 1 PARAMETER 2

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 343

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

Control change parameter assignments

❏ PRESET CHANNEL1

Control

Change#

MODE PARAMETER 1 PARAMETER 2

FADER H

INPUT

CH 1

2 CH 2

3 CH 3

4 CH 4

5 CH 5

6 CH 6

7 CH 7

8 CH 8

9 CH 9

10 CH10

11 CH11

12 CH12

13 CH13

14 CH14

15 CH15

16 CH16

17 CH17

18 CH18

19 CH19

20 CH20

21 CH21

22 CH22

23 CH23

24 CH24

OUTPUT

MIX 1

26 MIX 2

27 MIX 3

28 MIX 4

29 NO ASSIGN —

FADER H OUTPUT

STEREO AL

31 STEREO BL

FADER L

INPUT

CH 1

34 CH 2

35 CH 3

36 CH 4

37 CH 5

38 CH 6

39 CH 7

40 CH 8

41 CH 9

42 CH10

43 CH11

44 CH12

45 CH13

46 CH14

47 CH15

48 CH16

49 CH17

50 CH18

51 CH19

52 CH20

53 CH21

54 CH22

55 CH23

56 CH24

OUTPUT

MIX 1

58 MIX 2

59 MIX 3

60 MIX 4

61 NO ASSIGN —

FADER L OUTPUT

STEREO AL

63 STEREO BL

CH ON INPUT

CH 1

65 CH 2

66 CH 3

67 CH 4

68 CH 5

69 CH 6

70 CH 7

71 CH 8

72 CH 9

73 CH10

74 CH11

75 CH12

76 CH13

77 CH14

78 CH15

79 CH16

80 CH17

81 CH18

82 CH19

83 CH20

84 CH21

85 CH22

86 CH23

87 CH24

88 NO ASSIGN —

PAN/BALANCE INPUT

CH 1

90 CH 2

91 CH 3

92 CH 4

93 CH 5

94 CH 6

95 CH 7

102 CH 8

103 CH 9

104 CH10

105 CH11

106 CH12

107 CH13

108 CH14

109 CH15

110 CH16

111 CH17

112 CH18

113 CH19

114 CH20

115 CH21

116 CH22

117 CH23

118 CH24

119 NO ASSIGN —

Control

Change#

MODE PARAMETER 1 PARAMETER 2

Control change parameter assignments

344 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

❏ PRESET CHANNEL2

Control

Change#

MODE PARAMETER 1 PARAMETER 2

FADER H

INPUT

CH25

2 CH26

3 CH27

4 CH28

5 CH29

6 CH30

7 CH31

8 CH32

9 CH33

10 CH34

11 CH35

12 CH36

13 CH37

14 CH38

15 CH39

16 CH40

17 CH41

18 CH42

19 CH43

20 CH44

21 CH45

22 CH46

23 CH47

24 CH48

OUTPUT

MIX 5

26 MIX 6

27 MIX 7

28 MIX 8

29 NO ASSIGN —

CH ON OUTPUT

STEREO AL

31 STEREO BL

FADER L

INPUT

CH25

34 CH26

35 CH27

36 CH28

37 CH29

38 CH30

39 CH31

40 CH32

41 CH33

42 CH34

43 CH35

44 CH36

45 CH37

46 CH38

47 CH39

48 CH40

49 CH41

50 CH42

51 CH43

52 CH44

53 CH45

54 CH46

55 CH47

56 CH48

OUTPUT

MIX 5

58 MIX 6

59 MIX 7

60 MIX 8

61 NO ASSIGN —

BALANCE OUTPUT

STEREO AL

63 STEREO BL

CH ON INPUT

CH25

65 CH26

66 CH27

67 CH28

68 CH29

69 CH30

70 CH31

71 CH32

72 CH33

73 CH34

74 CH35

75 CH36

76 CH37

77 CH38

78 CH39

79 CH40

80 CH41

81 CH42

82 CH43

83 CH44

84 CH45

85 CH46

86 CH47

87 CH48

88 NO ASSIGN —

PAN/BALANCE INPUT

CH25

90 CH26

91 CH27

92 CH28

93 CH29

94 CH30

95 CH31

102 CH32

103 CH33

104 CH34

105 CH35

106 CH36

107 CH37

108 CH38

109 CH39

110 CH40

111 CH41

112 CH42

113 CH43

114 CH44

115 CH45

116 CH46

117 CH47

118 CH48

119 NO ASSIGN —

Control

Change#

MODE PARAMETER 1 PARAMETER 2

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 345

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

❏ PRESET CHANNEL3

Control

Change#

MODE PARAMETER 1 PARAMETER 2

INPUT EQ LOW GAIN

CH 1

2 CH 2

3 CH 3

4 CH 4

5 CH 5

6 CH 6

7 CH 7

8 CH 8

9 CH 9

10 CH10

11 CH11

12 CH12

13 CH13

14 CH14

15 CH15

16 CH16

17 CH17

18 CH18

19 CH19

20 CH20

21 CH21

22 CH22

23 CH23

24 CH24

FADER H OUTPUT

MIX 9

26 MIX10

27 MIX11

28 MIX12

29 NO ASSIGN —

BALANCE OUTPUT

MIX 1

31 MIX 3

NO ASSIGN —

FADER L OUTPUT

MIX 9

58 MIX10

59 MIX11

60 MIX12

61 NO ASSIGN —

BALANCE OUTPUT

MIX 5

63 MIX 7

INPUT EQ LOW FREQ

CH 1

65 CH 2

66 CH 3

67 CH 4

68 CH 5

69 CH 6

70 CH 7

71 CH 8

72 CH 9

73 CH10

74 CH11

75 CH12

76 CH13

77 CH14

78 CH15

79 CH16

80 CH17

81 CH18

82 CH19

83 CH20

84 CH21

85 CH22

86 CH23

87 CH24

88 NO ASSIGN —

INPUT EQ LOW Q

CH 1

90 CH 2

91 CH 3

92 CH 4

93 CH 5

94 CH 6

95 CH 7

102 CH 8

103 CH 9

104 CH10

105 CH11

106 CH12

107 CH13

108 CH14

109 CH15

110 CH16

111 CH17

112 CH18

113 CH19

114 CH20

115 CH21

116 CH22

117 CH23

118 CH24

119 NO ASSIGN —

Control

Change#

MODE PARAMETER 1 PARAMETER 2

Control change parameter assignments

346 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

❏ PRESET CHANNEL4

Control

Change#

MODE PARAMETER 1 PARAMETER 2

INPUT EQ LOW GAIN

CH25

2 CH26

3 CH27

4 CH28

5 CH29

6 CH30

7 CH31

8 CH32

9 CH33

10 CH34

11 CH35

12 CH36

13 CH37

14 CH38

15 CH39

16 CH40

17 CH41

18 CH42

19 CH43

20 CH44

21 CH45

22 CH46

23 CH47

24 CH48

FADER H OUTPUT

MIX13

26 MIX14

27 MIX15

28 MIX16

29 NO ASSIGN —

BALANCE OUTPUT

MIX 9

31 MIX11

NO ASSIGN —

FADER L OUTPUT

MIX13

58 MIX14

59 MIX15

60 MIX16

61 NO ASSIGN —

BALANCE OUTPUT

MIX13

63 MIX15

INPUT EQ LOW FREQ

CH25

65 CH26

66 CH27

67 CH28

68 CH29

69 CH30

70 CH31

71 CH32

72 CH33

73 CH34

74 CH35

75 CH36

76 CH37

77 CH38

78 CH39

79 CH40

80 CH41

81 CH42

82 CH43

83 CH44

84 CH45

85 CH46

86 CH47

87 CH48

88 NO ASSIGN —

INPUT EQ LOW Q

CH25

90 CH26

91 CH27

92 CH28

93 CH29

94 CH30

95 CH31

102 CH32

103 CH33

104 CH34

105 CH35

106 CH36

107 CH37

108 CH38

109 CH39

110 CH40

111 CH41

112 CH42

113 CH43

114 CH44

115 CH45

116 CH46

117 CH47

118 CH48

119 NO ASSIGN —

Control

Change#

MODE PARAMETER 1 PARAMETER 2

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 347

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

❏ PRESET CHANNEL5

Control

Change#

MODE PARAMETER 1 PARAMETER 2

INPUT EQ

LOW MID

GAIN

CH 1

2 CH 2

3 CH 3

4 CH 4

5 CH 5

6 CH 6

7 CH 7

8 CH 8

9 CH 9

10 CH10

11 CH11

12 CH12

13 CH13

14 CH14

15 CH15

16 CH16

17 CH17

18 CH18

19 CH19

20 CH20

21 CH21

22 CH22

23 CH23

24 CH24

CH ON OUTPUT

MIX 1

26 MIX 2

27 MIX 3

28 MIX 4

29 NO ASSIGN —

CH ON OUTPUT

MIX17

31 MIX18

NO ASSIGN —

CH ON OUTPUT

MIX 5

58 MIX 6

59 MIX 7

60 MIX 8

61 NO ASSIGN —

CH ON OUTPUT

MIX19

63 MIX20

INPUT EQ LOW MID FREQ

CH 1

65 CH 2

66 CH 3

67 CH 4

68 CH 5

69 CH 6

70 CH 7

71 CH 8

72 CH 9

73 CH10

74 CH11

75 CH12

76 CH13

77 CH14

78 CH15

79 CH16

80 CH17

81 CH18

82 CH19

83 CH20

84 CH21

85 CH22

86 CH23

87 CH24

88 NO ASSIGN —

INPUT EQ LOW MID Q

CH 1

90 CH 2

91 CH 3

92 CH 4

93 CH 5

94 CH 6

95 CH 7

102 CH 8

103 CH 9

104 CH10

105 CH11

106 CH12

107 CH13

108 CH14

109 CH15

110 CH16

111 CH17

112 CH18

113 CH19

114 CH20

115 CH21

116 CH22

117 CH23

118 CH24

119 NO ASSIGN —

Control

Change#

MODE PARAMETER 1 PARAMETER 2

Control change parameter assignments

348 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

❏ PRESET CHANNEL6

Control

Change#

MODE PARAMETER 1 PARAMETER 2

INPUT EQ

LOW MID

GAIN

CH25

2 CH26

3 CH27

4 CH28

5 CH29

6 CH30

7 CH31

8 CH32

9 CH33

10 CH34

11 CH35

12 CH36

13 CH37

14 CH38

15 CH39

16 CH40

17 CH41

18 CH42

19 CH43

20 CH44

21 CH45

22 CH46

23 CH47

24 CH48

CH ON OUTPUT

MIX 9

26 MIX10

27 MIX11

28 MIX12

29 NO ASSIGN —

CH ON OUTPUT

MIX21

31 MIX22

NO ASSIGN —

CH ON OUTPUT

MIX13

58 MIX14

59 MIX15

60 MIX16

61 NO ASSIGN —

CH ON OUTPUT

MIX23

63 MIX24

INPUT EQ LOW MID FREQ

CH25

65 CH26

66 CH27

67 CH28

68 CH29

69 CH30

70 CH31

71 CH32

72 CH33

73 CH34

74 CH35

75 CH36

76 CH37

77 CH38

78 CH39

79 CH40

80 CH41

81 CH42

82 CH43

83 CH44

84 CH45

85 CH46

86 CH47

87 CH48

88 NO ASSIGN —

INPUT EQ LOW MID Q

CH25

90 CH26

91 CH27

92 CH28

93 CH29

94 CH30

95 CH31

102 CH32

103 CH33

104 CH34

105 CH35

106 CH36

107 CH37

108 CH38

109 CH39

110 CH40

111 CH41

112 CH42

113 CH43

114 CH44

115 CH45

116 CH46

117 CH47

118 CH48

119 NO ASSIGN —

Control

Change#

MODE PARAMETER 1 PARAMETER 2

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 349

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

❏ PRESET CHANNEL7

Control

Change#

MODE PARAMETER 1 PARAMETER 2

INPUT EQ

HIGH MID

GAIN

CH 1

2 CH 2

3 CH 3

4 CH 4

5 CH 5

6 CH 6

7 CH 7

8 CH 8

9 CH 9

10 CH10

11 CH11

12 CH12

13 CH13

14 CH14

15 CH15

16 CH16

17 CH17

18 CH18

19 CH19

20 CH20

21 CH21

22 CH22

23 CH23

24 CH24

FADER H OUTPUT

MIX17

26 MIX18

27 MIX19

28 MIX20

29 NO ASSIGN —

BALANCE OUTPUT

MIX17

31 MIX19

NO ASSIGN —

FADER L OUTPUT

MIX17

58 MIX18

59 MIX19

60 MIX20

61 NO ASSIGN —

BALANCE OUTPUT

MIX21

63 MIX23

INPUT EQ

HIGH MID

FREQ

CH 1

65 CH 2

66 CH 3

67 CH 4

68 CH 5

69 CH 6

70 CH 7

71 CH 8

72 CH 9

73 CH10

74 CH11

75 CH12

76 CH13

77 CH14

78 CH15

79 CH16

80 CH17

81 CH18

82 CH19

83 CH20

84 CH21

85 CH22

86 CH23

87 CH24

88 NO ASSIGN —

INPUT EQ HIGH MID Q

CH 1

90 CH 2

91 CH 3

92 CH 4

93 CH 5

94 CH 6

95 CH 7

102 CH 8

103 CH 9

104 CH10

105 CH11

106 CH12

107 CH13

108 CH14

109 CH15

110 CH16

111 CH17

112 CH18

113 CH19

114 CH20

115 CH21

116 CH22

117 CH23

118 CH24

119 NO ASSIGN —

Control

Change#

MODE PARAMETER 1 PARAMETER 2

Control change parameter assignments

350 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

❏ PRESET CHANNEL8

Control

Change#

MODE PARAMETER 1 PARAMETER 2

INPUT EQ

HIGH MID

GAIN

CH25

2 CH26

3 CH27

4 CH28

5 CH29

6 CH30

7 CH31

8 CH32

9 CH33

10 CH34

11 CH35

12 CH36

13 CH37

14 CH38

15 CH39

16 CH40

17 CH41

18 CH42

19 CH43

20 CH44

21 CH45

22 CH46

23 CH47

24 CH48

FADER H OUTPUT

MIX21

26 MIX22

27 MIX23

28 MIX24

29 NO ASSIGN —

BALANCE OUTPUT

MATRIX 1

31 MATRIX 3

NO ASSIGN —

FADER L OUTPUT

MIX21

58 MIX22

59 MIX23

60 MIX24

61 NO ASSIGN —

BALANCE OUTPUT

MATRIX 5

63 MATRIX 7

INPUT EQ

HIGH MID

FREQ

CH25

65 CH26

66 CH27

67 CH28

68 CH29

69 CH30

70 CH31

71 CH32

72 CH33

73 CH34

74 CH35

75 CH36

76 CH37

77 CH38

78 CH39

79 CH40

80 CH41

81 CH42

82 CH43

83 CH44

84 CH45

85 CH46

86 CH47

87 CH48

88 NO ASSIGN —

INPUT EQ HIGH MID Q

CH25

90 CH26

91 CH27

92 CH28

93 CH29

94 CH30

95 CH31

102 CH32

103 CH33

104 CH34

105 CH35

106 CH36

107 CH37

108 CH38

109 CH39

110 CH40

111 CH41

112 CH42

113 CH43

114 CH44

115 CH45

116 CH46

117 CH47

118 CH48

119 NO ASSIGN —

Control

Change#

MODE PARAMETER 1 PARAMETER 2

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 351

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

❏ PRESET CHANNEL9

Control

Change#

MODE PARAMETER 1 PARAMETER 2

INPUT EQ HIGH GAIN

CH 1

2 CH 2

3 CH 3

4 CH 4

5 CH 5

6 CH 6

7 CH 7

8 CH 8

9 CH 9

10 CH10

11 CH11

12 CH12

13 CH13

14 CH14

15 CH15

16 CH16

17 CH17

18 CH18

19 CH19

20 CH20

21 CH21

22 CH22

23 CH23

24 CH24

FADER H OUTPUT

MATRIX 1

26 MATRIX 2

27 MATRIX 3

28 MATRIX 4

29 NO ASSIGN —

CH ON OUTPUT

MATRIX 1

31 MATRIX 2

NO ASSIGN —

FADER L OUTPUT

MATRIX 1

58 MATRIX 2

59 MATRIX 3

60 MATRIX 4

61 NO ASSIGN —

CH ON OUTPUT

MATRIX 3

63 MATRIX 4

INPUT EQ HIGH FREQ

CH 1

65 CH 2

66 CH 3

67 CH 4

68 CH 5

69 CH 6

70 CH 7

71 CH 8

72 CH 9

73 CH10

74 CH11

75 CH12

76 CH13

77 CH14

78 CH15

79 CH16

80 CH17

81 CH18

82 CH19

83 CH20

84 CH21

85 CH22

86 CH23

87 CH24

88 NO ASSIGN —

INPUT EQ HIGH Q

CH 1

90 CH 2

91 CH 3

92 CH 4

93 CH 5

94 CH 6

95 CH 7

102 CH 8

103 CH 9

104 CH10

105 CH11

106 CH12

107 CH13

108 CH14

109 CH15

110 CH16

111 CH17

112 CH18

113 CH19

114 CH20

115 CH21

116 CH22

117 CH23

118 CH24

119 NO ASSIGN —

Control

Change#

MODE PARAMETER 1 PARAMETER 2

Control change parameter assignments

352 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

❏ PRESET CHANNEL10

Control

Change#

MODE PARAMETER 1 PARAMETER 2

INPUT EQ HIGH GAIN

CH25

2 CH26

3 CH27

4 CH28

5 CH29

6 CH30

7 CH31

8 CH32

9 CH33

10 CH34

11 CH35

12 CH36

13 CH37

14 CH38

15 CH39

16 CH40

17 CH41

18 CH42

19 CH43

20 CH44

21 CH45

22 CH46

23 CH47

24 CH48

FADER H OUTPUT

MATRIX 5

26 MATRIX 6

27 MATRIX 7

28 MATRIX 8

29 NO ASSIGN —

CH ON OUTPUT

MATRIX 5

31 MATRIX 6

NO ASSIGN —

FADER L OUTPUT

MATRIX 5

58 MATRIX 6

59 MATRIX 7

60 MATRIX 8

61 NO ASSIGN —

CH ON OUTPUT

MATRIX 7

63 MATRIX 8

INPUT EQ HIGH FREQ

CH25

65 CH26

66 CH27

67 CH28

68 CH29

69 CH30

70 CH31

71 CH32

72 CH33

73 CH34

74 CH35

75 CH36

76 CH37

77 CH38

78 CH39

79 CH40

80 CH41

81 CH42

82 CH43

83 CH44

84 CH45

85 CH46

86 CH47

87 CH48

88 NO ASSIGN —

INPUT EQ HIGH Q

CH25

90 CH26

91 CH27

92 CH28

93 CH29

94 CH30

95 CH31

102 CH32

103 CH33

104 CH34

105 CH35

106 CH36

107 CH37

108 CH38

109 CH39

110 CH40

111 CH41

112 CH42

113 CH43

114 CH44

115 CH45

116 CH46

117 CH47

118 CH48

119 NO ASSIGN —

Control

Change#

MODE PARAMETER 1 PARAMETER 2

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 353

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

❏ PRESET CHANNEL11

Control

Change#

MODE PARAMETER 1 PARAMETER 2

INPUT ATT INPUT

CH 1

2 CH 2

3 CH 3

4 CH 4

5 CH 5

6 CH 6

7 CH 7

8 CH 8

9 CH 9

10 CH10

11 CH11

12 CH12

13 CH13

14 CH14

15 CH15

16 CH16

17 CH17

18 CH18

19 CH19

20 CH20

21 CH21

22 CH22

23 CH23

24 CH24

INPUT HPF FREQ

CH 1

26 CH 2

27 CH 3

28 CH 4

29 NO ASSIGN —

INPUT HPF FREQ

CH 5

31 CH 6

NO ASSIGN —

INPUT HPF FREQ

CH 7

58 CH 8

59 CH 9

60 CH10

61 NO ASSIGN —

INPUT HPF FREQ

CH11

63 CH12

INPUT HPF ON

CH 1

65 CH 2

66 CH 3

67 CH 4

68 CH 5

69 CH 6

70 CH 7

71 CH 8

72 CH 9

73 CH10

74 CH11

75 CH12

76 CH13

77 CH14

78 CH15

79 CH16

80 CH17

81 CH18

82 CH19

83 CH20

84 CH21

85 CH22

86 CH23

87 CH24

88 NO ASSIGN —

INPUT EQ LPF ON

CH 1

90 CH 2

91 CH 3

92 CH 4

93 CH 5

94 CH 6

95 CH 7

102 CH 8

103 CH 9

104 CH10

105 CH11

106 CH12

107 CH13

108 CH14

109 CH15

110 CH16

111 CH17

112 CH18

113 CH19

114 CH20

115 CH21

116 CH22

117 CH23

118 CH24

119 NO ASSIGN —

Control

Change#

MODE PARAMETER 1 PARAMETER 2

Control change parameter assignments

354 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

❏ PRESET CHANNEL12

Control

Change#

MODE PARAMETER 1 PARAMETER 2

INPUT ATT INPUT

CH25

2 CH26

3 CH27

4 CH28

5 CH29

6 CH30

7 CH31

8 CH32

9 CH33

10 CH34

11 CH35

12 CH36

13 CH37

14 CH38

15 CH39

16 CH40

17 CH41

18 CH42

19 CH43

20 CH44

21 CH45

22 CH46

23 CH47

24 CH48

INPUT HPF FREQ

CH13

26 CH14

27 CH15

28 CH16

29 NO ASSIGN —

INPUT HPF FREQ

CH17

31 CH18

NO ASSIGN —

INPUT HPF FREQ

CH19

58 CH20

59 CH21

60 CH22

61 NO ASSIGN —

INPUT HPF FREQ

CH23

63 CH24

INPUT HPF ON

CH25

65 CH26

66 CH27

67 CH28

68 CH29

69 CH30

70 CH31

71 CH32

72 CH33

73 CH34

74 CH35

75 CH36

76 CH37

77 CH38

78 CH39

79 CH40

80 CH41

81 CH42

82 CH43

83 CH44

84 CH45

85 CH46

86 CH47

87 CH48

88 NO ASSIGN —

INPUT EQ LPF ON

CH25

90 CH26

91 CH27

92 CH28

93 CH29

94 CH30

95 CH31

102 CH32

103 CH33

104 CH34

105 CH35

106 CH36

107 CH37

108 CH38

109 CH39

110 CH40

111 CH41

112 CH42

113 CH43

114 CH44

115 CH45

116 CH46

117 CH47

118 CH48

119 NO ASSIGN —

Control

Change#

MODE PARAMETER 1 PARAMETER 2

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 355

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

❏ PRESET CHANNEL13

Control

Change#

MODE PARAMETER 1 PARAMETER 2

SURROUND LFE H

CH 1

2 CH 2

3 CH 3

4 CH 4

5 CH 5

6 CH 6

7 CH 7

8 CH 8

9 CH 9

10 CH10

11 CH11

12 CH12

13 CH13

14 CH14

15 CH15

16 CH16

17 CH17

18 CH18

19 CH19

20 CH20

21 CH21

22 CH22

23 CH23

24 CH24

INPUT HPF FREQ

CH25

26 CH26

27 CH27

28 CH28

29 NO ASSIGN —

INPUT HPF FREQ

CH29

31 CH30

SURROUND LFE L

CH 1

34 CH 2

35 CH 3

36 CH 4

37 CH 5

38 CH 6

39 CH 7

40 CH 8

41 CH 9

42 CH10

43 CH11

44 CH12

45 CH13

46 CH14

47 CH15

48 CH16

49 CH17

50 CH18

51 CH19

52 CH20

53 CH21

54 CH22

55 CH23

56 CH24

INPUT HPF FREQ

CH31

58 CH32

59 CH33

60 CH34

61 NO ASSIGN —

INPUT HPF FREQ

CH35

63 CH36

SURROUND DIVERGENCE F

CH 1

65 CH 2

66 CH 3

67 CH 4

68 CH 5

69 CH 6

70 CH 7

71 CH 8

72 CH 9

73 CH10

74 CH11

75 CH12

76 CH13

77 CH14

78 CH15

79 CH16

80 CH17

81 CH18

82 CH19

83 CH20

84 CH21

85 CH22

86 CH23

87 CH24

88 NO ASSIGN —

INPUT EQ ON

CH 1

90 CH 2

91 CH 3

92 CH 4

93 CH 5

94 CH 6

95 CH 7

102 CH 8

103 CH 9

104 CH10

105 CH11

106 CH12

107 CH13

108 CH14

109 CH15

110 CH16

111 CH17

112 CH18

113 CH19

114 CH20

115 CH21

116 CH22

117 CH23

118 CH24

119 NO ASSIGN —

Control

Change#

MODE PARAMETER 1 PARAMETER 2

Control change parameter assignments

356 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

❏ PRESET CHANNEL14

Control

Change#

MODE PARAMETER 1 PARAMETER 2

SURROUND LFE H

CH25

2 CH26

3 CH27

4 CH28

5 CH29

6 CH30

7 CH31

8 CH32

9 CH33

10 CH34

11 CH35

12 CH36

13 CH37

14 CH38

15 CH39

16 CH40

17 CH41

18 CH42

19 CH43

20 CH44

21 CH45

22 CH46

23 CH47

24 CH48

INPUT HPF FREQ

CH37

26 CH38

27 CH39

28 CH40

29 NO ASSIGN —

INPUT HPF FREQ

CH41

31 CH42

SURROUND LFE L

CH25

34 CH26

35 CH27

36 CH28

37 CH29

38 CH30

39 CH31

40 CH32

41 CH33

42 CH34

43 CH35

44 CH36

45 CH37

46 CH38

47 CH39

48 CH40

49 CH41

50 CH42

51 CH43

52 CH44

53 CH45

54 CH46

55 CH47

56 CH48

INPUT HPF FREQ

CH43

58 CH44

59 CH45

60 CH46

61 NO ASSIGN —

INPUT HPF FREQ

CH47

63 CH48

SURROUND DIVERGENCE F

CH25

65 CH26

66 CH27

67 CH28

68 CH29

69 CH30

70 CH31

71 CH32

72 CH33

73 CH34

74 CH35

75 CH36

76 CH37

77 CH38

78 CH39

79 CH40

80 CH41

81 CH42

82 CH43

83 CH44

84 CH45

85 CH46

86 CH47

87 CH48

88 NO ASSIGN —

INPUT EQ ON

CH25

90 CH26

91 CH27

92 CH28

93 CH29

94 CH30

95 CH31

102 CH32

103 CH33

104 CH34

105 CH35

106 CH36

107 CH37

108 CH38

109 CH39

110 CH40

111 CH41

112 CH42

113 CH43

114 CH44

115 CH45

116 CH46

117 CH47

118 CH48

119 NO ASSIGN —

Control

Change#

MODE PARAMETER 1 PARAMETER 2

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 357

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

❏ PRESET CHANNEL15

Control

Change#

MODE PARAMETER 1 PARAMETER 2

SURROUND

LEFT-RIGHT

PAN

CH 1

2 CH 2

3 CH 3

4 CH 4

5 CH 5

6 CH 6

7 CH 7

8 CH 8

9 CH 9

10 CH10

11 CH11

12 CH12

13 CH13

14 CH14

15 CH15

16 CH16

17 CH17

18 CH18

19 CH19

20 CH20

21 CH21

22 CH22

23 CH23

24 CH24

DCA FADER H

DCA 1

26 DCA 2

27 DCA 3

28 DCA 4

29 NO ASSIGN —

MUTE MASTER ON

MASTER 1

31 MASTER 2

SURROUND

FRONT-REAR

PAN

CH 1

34 CH 2

35 CH 3

36 CH 4

37 CH 5

38 CH 6

39 CH 7

40 CH 8

41 CH 9

42 CH10

43 CH11

44 CH12

45 CH13

46 CH14

47 CH15

48 CH16

49 CH17

50 CH18

51 CH19

52 CH20

53 CH21

54 CH22

55 CH23

56 CH24

DCA FADER L

DCA 1

58 DCA 2

59 DCA 3

60 DCA 4

61 NO ASSIGN —

MUTE MASTER ON

MASTER 3

63 MASTER 4

NO ASSIGN —

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

Control

Change#

MODE PARAMETER 1 PARAMETER 2

Control change parameter assignments

358 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

❏ PRESET CHANNEL16

Control

Change#

MODE PARAMETER 1 PARAMETER 2

SURROUND

LEFT-RIGHT

PAN

CH25

2 CH26

3 CH27

4 CH28

5 CH29

6 CH30

7 CH31

8 CH32

9 CH33

10 CH34

11 CH35

12 CH36

13 CH37

14 CH38

15 CH39

16 CH40

17 CH41

18 CH42

19 CH43

20 CH44

21 CH45

22 CH46

23 CH47

24 CH48

DCA FADER H

DCA5

26 DCA6

27 DCA7

28 DCA8

29 NO ASSIGN —

MUTE MASTER ON

MASTER5

31 MASTER6

SURROUND

FRONT-REAR

PAN

CH25

34 CH26

35 CH27

36 CH28

37 CH29

38 CH30

39 CH31

40 CH32

41 CH33

42 CH34

43 CH35

44 CH36

45 CH37

46 CH38

47 CH39

48 CH40

49 CH41

50 CH42

51 CH43

52 CH44

53 CH45

54 CH46

55 CH47

56 CH48

DCA FADER L

DCA 5

58 DCA 6

59 DCA 7

60 DCA 8

61 NO ASSIGN —

MUTE MASTER ON

MASTER 7

63 MASTER 8

NO ASSIGN —

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

Control

Change#

MODE PARAMETER 1 PARAMETER 2

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 359

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

❏ CHANNEL _

Control

Change#

MODE PARAMETER 1 PARAMETER 2

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

Control

Change#

MODE PARAMETER 1 PARAMETER 2

NRPN parameter assignments

360 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

NRPN parameter assignments

PARAMETER

FROM

(HEX)

FADER

CHANNEL 0000 003F

MIX1-20,MATRIX1-8,ST A LR 0060 007D

CH to Mix LEVEL

MIX9 SEND 007E 00BD

MIX10 SEND 00DE 011D

MIX11 SEND 013E 017D

MIX12 SEND 019E 01DD

MIX13 SEND 01FE 023D

MIX14 SEND 025E 029D

MIX15 SEND 02BE 02FD

MIX16 SEND 031E 035D

MIX17 SEND 037E 03BD

MIX18 SEND 03DE 041D

MIX19 SEND 043E 047D

MIX20 SEND 049E 04DD

MIX1-20, MATRIX1-

8, ST A LR to Matrix

LEVEL

MATRIX1 SEND 04FE 0513

MATRIX2 SEND 0514 0529

MATRIX3 SEND 052A 053F

MATRIX4 SEND 0540 0555

MATRIX5 SEND 0556 056B

MATRIX6 SEND 056C 0581

MATRIX7 SEND 0582 0597

MATRIX8 SEND 0598 05AD

MIX1-8 to ST LEVEL MIX TO ST 05AE 05B5

CHANNEL 05B6 05F5

MIX1-20,MATRIX1-8,ST A LR 0616 0633

CH to Mix ON

MIX9 SEND 0634 0673

MIX10 SEND 0694 06D3

MIX11 SEND 06F4 0733

MIX12 SEND 0754 0793

MIX13 SEND 07B4 07F3

MIX14 SEND 0814 0853

MIX15 SEND 0874 08B3

MIX16 SEND 08D4 0913

MIX17 SEND 0934 0973

MIX18 SEND 0994 09D3

MIX19 SEND 09F4 0A33

MIX20 SEND 0A54 0A93

MIX1-20, MATRIX1-

8, ST A LR to Matrix

LEVEL

MATRIX1 SEND 0AB4 0AC9

MATRIX2 SEND 0ACA 0AC9

MATRIX3 SEND 0AE0 0ADF

MATRIX4 SEND 0AF6 0AF5

MATRIX5 SEND 0B0C 0B0B

MATRIX6 SEND 0B22 0B21

MATRIX7 SEND 0B38 0B37

MATRIX8 SEND 0B4E 0B4D

MIX1-8 to ST ON MIX TO ST 0B64 0B6B

PHASE CHANNEL 0B6C 0BAB

INSERT ON

CHANNEL 0BCC 0C03

MIX1-20,MATRIX1-8,ST A LR 0C2C 0C49

CH to Mix PRE/

POST

MIX9 SEND 0C4A 0C89

MIX10 SEND 0CAA 0CE9

MIX11 SEND 0D0A 0D49

MIX12 SEND 0D6A 0DA9

MIX13 SEND 0DCA 0E09

MIX14 SEND 0E2A 0E69

MIX15 SEND 0E8A 0EC9

MIX16 SEND 0EEA 0F29

MIX17 SEND 0F4A 0F89

MIX18 SEND 0FAA 0FE9

MIX19 SEND 100A 1049

MIX20 SEND 106A 10A9

INPUT DELAY

ON 10CA 1101

TIME HIGH 112A 1161

TIME LOW 118A 11C1

MIX1-20,MATRIX1-

8,ST A LR OUTPUT

DELAY

ON 12AA 12C7

TIME HIGH 12C8 12E5

TIME LOW 12E6 1303

EQ CH & MIX1-20,

MATRIX1-8, ST A LR

OUTPUT(LOWER)

ON 1304 1381

Q LOW 1382 13FF

F LOW 1400 147D

G LOW 147E 14FB

Q LO-MID 14FC 1579

F LO-MID 157A 15F7

G LO-MID 15F8 1675

Q HI-MID 1676 16F3

F HI-MID 16F4 1771

G HI-MID 1772 17EF

Q HIGH 17F0 186D

F HIGH 186E 18EB

G HIGH 18EC 1969

ATT 196A 19A9

HPF ON 19E8 1A65

LPF ON 1A66 1AE3

GATE

ON 1AE4 1B1B

ATTACK 1B44 1B7B

THRESH 1BA4 1BDB

RANGE 1C04 1C3B

HOLD 1C64 1C9B

DECAY 1CC4 1CFB

COMP CH & MIX1-

20, MATRIX1-8, ST

A LR OUTPUT

ON 1D24 1DA1

ATTACK 1DA2 1E1F

THRESH 1E20 1E9D

RELEASE 1E9E 1F1B

RATIO 1F1C 1F99

GAIN 1F9A 2017

KNEE 2018 2095

PAN CHANNEL 2096 20D5

CH to MIX PAN

MIX9-10 20F6 2135

MIX11-12 2156 2195

MIX13-14 21B6 21F5

MIX15-16 2216 2255

MIX17-18 2276 22B5

MIX19-20 22D6 2315

MIX1-20, ST A LR to

Matrix PAN

MATRIX1,2 2336 234B

MATRIX3,4 234C 2361

MATRIX5,6 2362 2377

MATRIX7,8 2378 238D

MIX1-8 to ST PAN MIX TO ST 238E 2395

BALANCE MIX1-20,MATRIX1-8,ST A LR 2396 23B3

SURROUND

LFE 23B4 23F3

DIV (F) 2414 2453

LR 2474 24B3

FR 24D4 2513

PARAMETER

FROM

(HEX)

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 361

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

GEQ13-20

ON 2534 253B

GAIN1 253C 2543

GAIN2 2544 254B

GAIN3 254C 2553

GAIN4 2554 255B

GAIN5 255C 2563

GAIN6 2564 256B

GAIN7 256C 2573

GAIN8 2574 257B

GAIN9 257C 2583

GAIN10 2584 258B

GAIN11 258C 2593

GAIN12 2594 259B

GAIN13 259C 25A3

GAIN14 25A4 25AB

GAIN15 25AC 25B3

GAIN16 25B4 25BB

GAIN17 25BC 25C3

GAIN18 25C4 25CB

GAIN19 25CC 25D3

GAIN20 25D4 25DB

GAIN21 25DC 25E3

GAIN22 25E4 25EB

GAIN23 25EC 25F3

GAIN24 25F4 25FB

GAIN25 25FC 2603

GAIN26 2604 260B

GAIN27 260C 2613

GAIN28 2614 261B

GAIN29 261C 2623

GAIN30 2624 262B

GAIN31 262C 2633

EFFECT 1-8

BYPASS 26B4 26BB

MIX 26BC 26C3

PARAM1 26C4 26CB

PARAM2 26CC 26D3

PARAM3 26D4 26DB

PARAM4 26DC 26E3

PARAM5 26E4 26EB

PARAM6 26EC 26F3

PARAM7 26F4 26FB

PARAM8 26FC 2703

PARAM9 2704 270B

PARAM10 270C 2713

PARAM11 2714 271B

PARAM12 271C 2723

PARAM13 2724 272B

PARAM14 272C 2733

PARAM15 2734 273B

PARAM16 273C 2743

PARAM17 2744 274B

PARAM18 274C 2753

PARAM19 2754 275B

PARAM20 275C 2763

PARAM21 2764 276B

PARAM22 276C 2773

PARAM23 2774 277B

PARAM24 277C 2783

PARAM25 2784 278B

PARAM26 278C 2793

PARAM27 2794 279B

PARAM28 279C 27A3

PARAM29 27A4 27AB

PARAM30 27AC 27B3

PARAM31 27B4 27BB

PARAM32 27BC 27C3

PARAMETER

FROM

(HEX)

GEQ 1-6

ON 27C4 27C9

GAIN1 27CA 27CF

GAIN2 27D0 27D5

GAIN3 27D6 27DB

GAIN4 27DC 27E1

GAIN5 27E2 27E7

GAIN6 27E8 27ED

GAIN7 27EE 27F3

GAIN8 27F4 27F9

GAIN9 27FA 27FF

GAIN10 2800 2805

GAIN11 2806 280B

GAIN12 280C 2811

GAIN13 2812 2817

GAIN14 2818 281D

GAIN15 281E 2823

GAIN16 2824 2829

GAIN17 282A 282F

GAIN18 2830 2835

GAIN19 2836 283B

GAIN20 283C 2841

GAIN21 2842 2847

GAIN22 2848 284D

GAIN23 284E 2853

GAIN24 2854 2859

GAIN25 285A 285F

GAIN26 2860 2865

GAIN27 2866 286B

GAIN28 286C 2871

GAIN29 2872 2877

GAIN30 2878 287D

GAIN31 287E 2883

SURROUND DIV R 2884 28C3

FADER MIX21-24,ST B LR 28E4 28E9

CH to Mix LEVEL

MIX1 SEND 28EA 2929

MIX2 SEND 292A 2969

MIX3 SEND 296A 29A9

MIX4 SEND 29AA 29E9

MIX5 SEND 29EA 2A29

MIX6 SEND 2A2A 2A69

MIX7 SEND 2A6A 2AA9

MIX8 SEND 2AAA 2AE9

MIX21 SEND 2AEA 2B29

MIX22 SEND 2B2A 2B69

MIX23 SEND 2B6A 2BA9

MIX24 SEND 2BAA 2BE9

MIX21-24, ST B LR

to Matrix LEVEL

MATRIX1 SEND 2BEA 2BEF

MATRIX2 SEND 2BF0 2BF5

MATRIX3 SEND 2BF6 2BFB

MATRIX4 SEND 2BFC 2C01

MATRIX5 SEND 2C02 2C07

MATRIX6 SEND 2C08 2C0D

MATRIX7 SEND 2C0E 2C13

MATRIX8 SEND 2C14 2C19

MIX21-24 to ST

LEVEL

MIX TO ST 2C1A 2C29

ON MIX21-24,ST B LR 2C2A 2C2F

PARAMETER

FROM

(HEX)

NRPN parameter assignments

362 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

CH to Mix ON

MIX1 SEND 2C30 2C6F

MIX2 SEND 2C70 2CAF

MIX3 SEND 2CB0 2CEF

MIX4 SEND 2CF0 2D2F

MIX5 SEND 2D30 2D6F

MIX6 SEND 2D70 2DAF

MIX7 SEND 2DB0 2DEF

MIX8 SEND 2DF0 2E2F

MIX21 SEND 2E30 2E6F

MIX22 SEND 2E70 2EAF

MIX23 SEND 2EB0 2EEF

MIX24 SEND 2EF0 2F2F

MATRIX SEND 2F30 2F35

MIX TO ST 2F36 2F45

INSERT ON MIX21-24,ST B LR 2F46 2F4B

CH to Mix PRE/

POST

MIX1 SEND 2F4C 2F8B

MIX2 SEND 2F8C 2FCB

MIX3 SEND 2FCC 300B

MIX4 SEND 300C 304B

MIX5 SEND 304C 308B

MIX6 SEND 308C 30CB

MIX7 SEND 30CC 310B

MIX8 SEND 310C 314B

MIX21 SEND 314C 318B

MIX22 SEND 318C 31CB

MIX23 SEND 31CC 320B

MIX24 SEND 320C 324B

MIX1-20, ST B LR

OUTPUT DELAY

ON 324C 3251

TIME HIGH 3252 3257

TIME LOW 3258 325D

EQ MIX21-24, ST A

LR OUT-

PUT(LOWER)

ON 325E 3263

Q LOW 3264 3269

F LOW 326A 326F

G LOW 3270 3275

Q LO-MID 3276 327B

F LO-MID 327C 3281

G LO-MID 3282 3287

Q HI-MID 3288 328D

F HI-MID 328E 3293

G HI-MID 3294 3299

Q HIGH 329A 329F

F HIGH 32A0 32A5

G HIGH 32A6 32AB

HPF ON 32AC 32B1

LPF ON 32B2 32B7

EQ OUTPUT

(HIGHER)

E Q 32B8 32D3

E F 32D4 32EF

E G 32F0 330B

F Q 330C 3327

F F 3328 3343

F G 3344 335F

G Q 3360 337B

G F 337C 3397

G G 3398 33B3

H Q 33B4 33CF

H F 33D0 33EB

H G 33EC 3407

E HPF ON/OFF 3408 3423

H LPF ON/OFF 3424 343F

INPUT EQ LOW TYPE(P/S/F) 3440 347F

INPUT EQ HIGH TYPE(P/S/F) 3480 34BF

OUTPUT EQ

A TYPE(P/S/F) 34C0 34E3

D TYPE(P/S/F) 34E4 3507

E TYPE(P/S/F) 3508 3523

H TYPE(P/S/F) 3524 353F

PARAMETER

FROM

(HEX)

OUTPUT EQ

A BYPASS 3540 3563

B BYPASS 3564 3587

C BYPASS 3588 35AB

D BYPASS 35AC 35CF

E BYPASS 35D0 35EB

F BYPASS 35EC 3607

G BYPASS 3608 3623

H BYPASS 3624 363F

IN HPF F 3640 367F

COMP MIX21-24,

ST A LR OUTPUT

ON 3680 3685

ATTACK 3686 368B

THRESH 368C 3691

RELEASE 3692 3697

RATIO 3698 369D

GAIN 369E 36A3

KNEE 36A4 36A9

PAN MIX1-2 36AA 36E9

CH to MIX PAN

MIX3-4 36EA 3729

MIX5-6 372A 3769

MIX7-8 376A 37A9

MIX21-22 37AA 37E9

MIX23-24 37EA 3829

MIX21-24, ST B LR

to Matrix PAN

MATRIX1,2 382A 382F

MATRIX3,4 3830 3835

MATRIX5,6 3836 383B

MATRIX7,8 383C 3841

MIX9-24 to ST PAN MIX TO ST 3842 3851

GEQ7-12

ON 3852 3857

GAIN1 3858 385D

GAIN2 385E 3863

GAIN3 3864 3869

GAIN4 386A 386F

GAIN5 3870 3875

GAIN6 3876 387B

GAIN7 387C 3881

GAIN8 3882 3887

GAIN9 3888 388D

GAIN10 388E 3893

GAIN11 3894 3899

GAIN12 389A 389F

GAIN13 38A0 38A5

GAIN14 38A6 38AB

GAIN15 38AC 38B1

GAIN16 38B2 38B7

GAIN17 38B8 38BD

GAIN18 38BE 38C3

GAIN19 38C4 38C9

GAIN20 38CA 38CF

GAIN21 38D0 38D5

GAIN22 38D6 38DB

GAIN23 38DC 38E1

GAIN24 38E2 38E7

GAIN25 38E8 38ED

GAIN26 38EE 38F3

GAIN27 38F4 38F9

GAIN28 38FA 38FF

GAIN29 3900 3905

GAIN30 3906 390B

GAIN31 390C 3911

LCR IN, MIX

ON/OFF 3912 3969

CSR 396A 39C1

DIRECT OUT ON/OFF 39C2 39F9

CH TO STEREO ON/OFF 3A02 3A41

DCA

ON/OFF 3A42 3A49

LEVEL 3A4E 3A55

MUTE MASTER ON/OFF 3A5A 3A61

RECALL SAFE ON/OFF 3A66 3AE6

PARAMETER

FROM

(HEX)

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 363

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

GAIN1 3B06 3B14

GAIN2 3B16 3B24

GAIN3 3B26 3B34

GAIN4 3B36 3B44

GAIN5 3B46 3B54

GAIN6 3B56 3B64

GAIN7 3B66 3B74

GAIN8 3B76 3B84

+48v 1 3B86 3B94

+48v 2 3B96 3BA4

+48v 3 3BA6 3BB4

+48v 4 3BB6 3BC4

+48v 5 3BC6 3BD4

+48v 6 3BD6 3BE4

+48v 7 3BE6 3BF4

+48v 8 3BF6 3C04

HPF1 3C06 3C14

HPF2 3C16 3C24

HPF3 3C26 3C34

HPF4 3C36 3C44

HPF5 3C46 3C54

HPF6 3C56 3C64

HPF7 3C66 3C74

HPF8 3C76 3C84

GEQ

ON 3C86 3C99

L LOW BYPASS 3C9A 3CAD

L LOW Q 3CAE 3CC1

L LOW FREQ 3CC2 3CD5

L LOW GAIN 3CD6 3CE9

L LOW MID BYPASS 3CEA 3CFD

L LOW MID Q 3CFE 3D11

L LOW MID FREQ 3D12 3D25

L LOW MID GAIN 3D26 3D39

L HIGH MID BYPASS 3D3A 3D4D

L HIGH MID Q 3D4E 3D61

L HIGH MID FREQ 3D62 3D75

L HIGH MID GAIN 3D76 3D89

L HIGH BYPASS 3D8A 3D9D

L HIGH Q 3D9E 3DB1

L HIGH FREQ 3DB2 3DC5

L HIGH GAIN 3DC6 3DD9

U LOW BYPASS 3DDA 3DED

U LOW Q 3DEE 3E01

U LOW FREQ 3E02 3E15

U LOW GAIN 3E16 3E29

U LOW MID BYPASS 3E2A 3E3D

U LOW MID Q 3E3E 3E51

U LOW MID FREQ 3E52 3E65

U LOW MID GAIN 3E66 3E79

U HIGH MID BYPASS 3E7A 3E8D

U HIGH MID Q 3E8E 3EA1

U HIGH MID FREQ 3EA2 3EB5

U HIGH MID GAIN 3EB6 3EC9

U HIGH BYPASS 3ECA 3EDD

U HIGH Q 3EDE 3EF1

U HIGH FREQ 3EF2 3F05

U HIGH GAIN 3F06 3F19

L LOW TYPE 3F1A 3F2D

L HIGH TYPE 3F2E 3F41

U LOW TYPE 3F42 3F55

U HIGH TYPE 3F56 3F69

L HPF ON 3F6A 3F7D

L LPF ON 3F7E 3F91

U HPF ON 3F92 3FA5

U LPF ON 3FA6 3FB9

PARAMETER

FROM

(HEX)

*1. For EQ or COMP parameters that include INPUT CH and OUTPUT,

the OUTPUT is assigned starting at 96 (60h) after the ﬁrst number.

Thus, the numbers from immediately after INPUT CH until immedi-

ately before OUTPUT are unassigned.

Channel Library List

364 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

Channel Library List

This table lists the parameters that are saved in the channel library for INPUT/ST IN channels, MIX channels, MATRIX chan-

nels, and STEREO A/B channels.

INPUT/ST IN MIX MATRIX STEREO A/B

LCR On/Off

LCR Center-Side Ratio

Fade Time On/Off

Fade Time Start Offset

Fade Time Fading Time

Insert In On/Off

Insert Point

Direct Out On/Off

Direct Out Point

Phase

On/Off

To Stereo Pan

Master Balance

Level Master Level

Attenuator

GATE On/Off

GATE Key In Filter

GATE Filter Type

GATE Filter Freq.

GATE Filter Q

GATE Type

GATE Attack

GATE Range

GATE Hold

GATE Decay

GATE Threshold

COMP LINK 1-8 COMP LINK A-H

COMP On/Off

COMP Key In Type

COMP Attack

COMP Release

COMP Ratio

COMP OutGain

COMP Knee/Width

COMP Threshold

EQ LINK 1-8 EQ LINK A-F EQ LINK G,H EQ LINK A-F

HPF On/Off

EQ HPF On/

Off x2

EQ HPF On/

Off

EQ HPF On/

Off x2

HPF Freq

EQ Type 1,2

EQ On/Off

EQ Filter Type x2

EQ Filter Type

EQ LPF On/Off

EQ Q x4 EQ Q x8 EQ Q x4 EQ Q x8

EQ Freq x4 EQ Freq x8 EQ Freq x4 EQ Freq x8

EQ Gain x4 EQ Gain x8 EQ Gain x4 EQ Gain x8

EQ Bypass x8 EQ Bypass x4 EQ Bypass x8

Delay On/Off

Delay Time

Surround LFE

Surround Div.

Surround Div.Rear

Surround LR Pan

Surround FR Pan

Surround Div.Link

Mute Group 1-8 On/Off

DCA Group 1-8

On/Off

DCA Group

7,8 On/Off

DCA Group

7,8 On/Off

DCA Group

7,8 On/Off

To Stereo On/Off

To Stereo

Point

Mix Send Pre

Point

Mix Send Post

Point

Mix Send Follow

Pan Vari

Mix Send Follow

Pan Fixed

Mix Send 1-24

On/Off

Mix Send 1-24

Pre/Post

Mix Send 1-24

Level

Mix Send 1-24

Pan

To Matrix On/

Off

To Matrix On/

Off

To Matrix

Point

To Matrix

Point

To Matrix 1-8

Level

To Matrix 1-8

Level

To Matrix 1-8

Pan

To Matrix 1-8

Pan

Selective Recall On

Selective Recall Parameter

INPUT/ST IN MIX MATRIX STEREO A/B

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 365

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

List of parameters available for Pair, Recall Safe or OUTPUT

ISOLATION operation

The following table illustrates which parameters for the paired channels can be linked and which settings for each parameter

can be selected for Recall Safe or OUTPUT ISOLATION operation.

: Parameters of paired channels are linked.

–:Not subject to Pairing / Recall Safe / Output Isolation

❏ Input channels ❏ MIX channels

Parameter Pair Recall Safe

Recall Safe —

GANG pos-

sible on HA

HA (not ALL)

NAME

—

PHASE — INPUT ALL

MS DECODE — INPUT ALL

LCR INPUT ALL

Fade Time INPUT FADER, ALL

Insert INPUT ALL

Direct Out INPUT ALL

On INPUT ALL

Fader INPUT FADER, ALL

PAN GANG INPUT ALL

Att GANG INPUT ATT, ALL

Gate INPUT GATE, ALL

Comp INPUT COMP, ALL

HPF INPUT EQ, ALL

EQ INPUT EQ, ALL

Delay On INPUT DELAY, ALL

Delay TIME GANG INPUT DELAY, ALL

Surround LFE INPUT ALL

Surround Div INPUT ALL

Surround Div Rear INPUT ALL

Surround Div Link INPUT ALL

Mute Assign INPUT ALL

DCA Assign INPUT ALL

To Stereo On INPUT ALL

To Mix Follow Pan INPUT MIX SEND, ALL

To Mix ON INPUT MIX SEND, ALL

To Mix LEVEL INPUT MIX SEND, ALL

To Mix PAN INPUT MIX SEND, ALL

To Mix PRE/POST INPUT MIX SEND, ALL

PAIR INPUT ALL

Global Paste —

Solo Safe —

Cue —

Key In Cue —

Mute Safe —

Selective Recall —

Tracking Recall —

Parameter Pair Recall Safe ISOLATION

Recall Safe —

LCR MIX ALL

Fade Time MIX FADER, ALL

Insert MIX ALL

MIX INSERT,

MIX ALL

On MIX ALL

Fader MIX FADER, ALL

BALANCE — MIX ALL

Comp MIX COMP, ALL

EQ MIX EQ, ALL

Delay On MIX DELAY, ALL

Delay TIME GANG MIX DELAY, ALL

Mute Assign MIX ALL

DCA Assign MIX ALL

To Mix ON CH to MIX (not ALL)

To Mix LEVEL CH to MIX (not ALL)

To Mix Pan — CH to MIX (not ALL)

To Mix PRE/POST CH to MIX (not ALL)

To Matrix ON MIX TO MTRX, ALL

To Matrix LEVEL MIX TO MTRX, ALL

To Matrix POINT MIX TO MTRX, ALL

To Matrix PAN — MIX ALL

To Stereo On MIX ALL

To Stereo Point MIX ALL

Post To ST MIX ALL

Mute Assign MIX ALL

DCA Assign MIX ALL

PAIR MIX ALL

VARI/FIX MIX ALL

Global Paste —

Solo Safe —

Cue —

Mute Safe —

Selective Recall —

Tracking Recall —

Patch — —

MIX PATCH,

MIX ALL

OUTPUT ISOLA-

TION

—

List of parameters available for Pair, Recall Safe or OUTPUT ISOLATION operation

366 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

❏ MATRIX channels ❏ STEREO channels

❏ Other

* The parameter becomes eligible for Recall Safe if the library link is

turned off in the SCENE screen.

** If you set this to OUTPUT ISOLATION, it may also become impossi-

ble to change the DSP CONFIGURATION setting.

Parameter Pair Recall Safe ISOLATION

Recall Safe —

Fade Time MATRIX FADER, ALL

Insert MATRIX ALL

MATRIX INSERT,

MATRIX ALL

On MATRIX ALL

Fader MATRIX FADER, ALL

BALANCE — MATRIX ALL

Comp MATRIX COMP, ALL

EQ MATRIX EQ, ALL

Delay On MATRIX DELAY, ALL

Delay TIME GANG MATRIX DELAY, ALL

Mute Assign MATRIX ALL

DCA Assign MATRIX ALL

PAIR MATRIX ALL

Global Paste —

Solo Safe —

Cue —

Mute Safe —

Selective Recall —

Tracking Recall —

Patch — —

MIX PATCH,

MIX ALL

OUTPUT ISOLA-

TION

—

Parameter Pair Recall Safe ISOLATION

Recall Safe —

Fade Time ST FADER, ALL

Insert ST ALL ST INSERT, ST ALL

On ST ALL

Fader ST FADER, ALL

BALANCE — ST ALL

Comp ST COMP, ALL

EQ ST EQ ALL

Delay On ST DELAY, ALL

Delay TIME GANG ST DELAY, ALL

Mute Assign ST ALL

DCA Assign ST ALL

MONO — ST ALL

To Matrix On ST TO MTRX, ALL

To Matrix LEVEL ST TO MTRX, ALL

To Matrix POINT ST TO MTRX, ALL

To Matrix PAN — ST ALL

Global Paste —

Solo Safe —

Cue —

Mute Safe —

Selective Recall —

Tracking Recall —

Patch — —

MIX PATCH,

MIX ALL

OUTPUT ISOLA-

TION

—

Parameter Pair Recall Safe ISOLATION

INPUT PATCH

Turn off the library link.* —

OUTPUT PATCH

Turn off the library link.* —

EFF1-8

EFF 1-8 **

GEQ 1-20 LINK GEQ 1-20 **

DCA FADER,MUTE

DCA1-8 —

DCA FADE TIME

DCA1-8 —

DCA NAME

DCA1-8 (WITH NAME) —

MUTE MASTER

MUTE MASTER —

MIDI REMOTE

MIDI REMOTE A-D —

PLUG-IN

PLUG-IN 1-4 —

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 367

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

The following table lists the behavior of channel parameters when INPUT/ST IN channels, MIX channels, or MATRIX chan-

nels are paired.

❏ Parameters that are copied when pair-

ing is enabled

❏ Parameters that are turned on when

pairing is enabled

❏ Parameters that are not modiﬁed when

pairing is enabled (reset if RESET BOTH

is selected)

❏ Parameters that are not modiﬁed when

pairing is enabled (not reset even if

RESET BOTH is selected)

INPUT/ST IN MIX MATRIX

LCR On/Off

LCR Center-Side Ratio

Fade Time On/Off

Fade Time Start Offset

Fade Time Fading Time

Insert In On/Off

Insert Point

Direct Out On/Off

Direct Out Point

On/Off

Level Master Level

GATE On/Off

GATE Key In Source

GATE Key In Filter On

GATE Filter Type

GATE Filter Freq.

GATE Filter Q

GATE Type

GATE Attack

GATE Range

GATE Hold

GATE Decay

GATE Threshold

COMP LINK 1-8 COMP LINK A-H

COMP On/Off

COMP Key In Source

COMP Key In Type

COMP Attack

COMP Release

COMP Ratio

COMP OutGain

COMP Knee/Width

COMP Threshold

EQ LINK 1-8 EQ LINK A-F EQ LINK G,H

HPF On/Off EQ HPF On/Off x2 EQ HPF On/Off

HPF Freq

EQ Type 1,2

EQ On/Off

EQ Filter Type x2 EQ Filter Type x4 EQ Filter Type x2

EQ LPF On/Off EQ LPF On/Off x2 EQ LPF On/Off

EQ Q x4 EQ Q x8 EQ Q x4

EQ Freq x4 EQ Freq x8 EQ Freq x4

EQ Gain x4 EQ Gain x8 EQ Gain x4

EQ Bypass x8 EQ Bypass x4

Delay On/Off

Surround LFE

Surround Div.

Surround Div.Rear

Surround Div.Link

Mute Group 1-8 On/Off

DCA Group 1-8 On/Off DCA Group 7,8 On/Off

To Stereo On/Off

To Stereo Point

Mix Send Pre Point Mix Send Post Point

Mix Send Follow Pan Vari

Mix Send Follow Pan

Fixed

Mix Send 1-24 On/Off

Mix Send 1-24 Pre/Post

Mix Send 1-24 Level

To Matrix On/Off

To Matrix Point

Selective Recall On

Selective Recall Parameter

Recall Safe On

Recall Safe Parameter

Mute Safe On

Tracking On/Off

Tracking Level

Solo Safe On/Off

Cue/Solo On/Off

CH COPY CH SELECT

GLOBAL PASTE CH SELECT

OUTPUT ISOLATION PARAMETER

INPUT/ST IN MIX MATRIX

Attenuator Gang

Gate Stereo Link

Comp Stereo Link

Delay Gang

INPUT/ST IN MIX MATRIX

Phase

To Stereo Pan

Master Balance

Attenuator

Delay Time

Surround LR Pan

Surround FR Pan

Mix Send 1-24 Pan

To Matrix 1-8 Level

To Matrix 1-8 Pan

Input Pan Mode

Surround Link On/Off

Surround Link Pattern

M-S Encode On/Off

M-S Encode S-Gain

INPUT/ST IN MIX MATRIX

Mix Type

(VARI,FIX,SURR)

TB On/Off

OSC On/Off

MONITOR DEFINE On/Off

INPUT/ST IN MIX MATRIX

MIDI Data Format

368 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

MIDI Data Format

This section explains the format of the data that the PM5D is able to understand, send, and receive.

In addition to the messages described here, you can use the MIDI REMOTE function or the MIDI EVENT settings of the

SCENE function to transmit any type of command.

1 CHANNEL MESSAGE

1.1 NOTE OFF (8n)

Reception

These messages are echoed to MIDI OUT if [OTHER ECHO] is ON.

They are received if [Rx CH] matches, and used to control effects.

1.2 NOTE ON (9n)

Reception

These messages are echoed to MIDI OUT if [OTHER ECHO] is ON.

They are received if [Rx CH] matches, and used to control effects.

1.3 CONTROL CHANGE (Bn)

Tw o types of control change can be transmitted and received; [NRPN] (Non-

Registered Parameter Numbers) and freely-assigned [TABLE] (16CH x 110)

messages. Select either [TABLE] or [NRPN].

Reception

These messages are echoed to MIDI OUT if [Control Change ECHO] is ON.

If [TABLE MULTI] is selected, these messages are received when [Control

Change Rx] is ON, and will control parameters according to the settings of the

[Control assign table]. If [TABLE SINGLE] is selected, these messages are

received when [Control Change Rx] is ON and [Rx CH] matches, and will

control parameters according to the settings of the [Control assign table]. For

the parameters that can be assigned, refer to p.341.

If [NRPN] is selected, these messages are received when [Control Change Rx] is

ON and the [Rx CH] matches; the four messages NRPN control number (62h,

63h) and DATA ENTRY control number (06h, 26h) are used to control the

speciﬁed parameter.

Transmission

If [TABLE MULTI] is selected, and if [Control Change Tx] is ON when you

operate a parameter that is assigned in the [Control assign table], these

messages will be transmitted. If [TABLE SINGLE] is selected, and if [Control

Change Tx] is ON when you operate a parameter that is assigned in the [Control

assign table], these messages are transmitted on the [Tx CH] channel. For the

parameters that can be assigned, refer to p.341.

If [NRPN] is selected, and if [Control Change Tx] is ON when you operate a

speciﬁed parameter, the four messages NRPN control number (62h, 63h) and

DATA ENTRY control number (06h, 26h) are transmitted on the [Tx CH]

channel.

Control Change messages are not used for transmission to PM5D Editor

because there is no guarantee that the contents of the assignment tables will

match. (Parameter Change messages are always used.)

Control Change numbers 0 and 32 are for selecting banks.

If [TABLE] is selected

Equation for converting a Control Value to parameter data

paramSteps = paramMax - paramMin + 1;

add = paramWidth / paramSteps;

mod = paramWidth - add * paramSteps;

curValue = parm * add + mod / 2;

(1) If the assigned parameter has fewer than 128 steps

paramWidth = 128; rxValue = Control value;

(2) If the assigned parameter has 128 or more but less than

16,384 steps

paramWidth = 16384;

(2-1) When High and Low data is received

rxValue = Control value(High) * 128 + Control value(Low);

(2-2) When Low data is received

rxValue = (curValue & 16256) + Control value(Low);

(2-3) When High data is received

rxValue = Control value(High) * 128 + (curValue & 127);

(3) If the assigned parameter has 16,384 or more but less than

2,097,152 steps

paramWidth = 2097152;

(3-1) When High, Middle, and Low data is received

rxValue = Control value(High) * 16384 + Control value(Middle) * 128 + Control

value(Low);

(3-2) When only Low data is received

rxValue = (curValue & 2097024) + Control value(Low);

(3-3) When only Middle data is received

rxValue = (curValue & 2080895) + Control value(Middle) * 128;

(3-4) When only High data is received

rxValue = (curValue & 16383) + Control value(High) * 16384;

(3-5) When only Middle and Low data is received

rxValue = (curValue & 2080768) + Control value(Middle) * 128 + Control

value(Low);

(3-6) When only High and Low data is received

rxValue = (curValue & 16256) + Control value(High) * 16384 + Control value(Low);

(3-7) When only High and Middle data is received

rxValue = (curValue & 127) + Control value(High) * 16384 + Control value(Middle)

* 128;

if ( rxValue > paramWidth)

rxValue = paramWidth;

param = ( rxValue - mod / 2) / add;

If [NRPN] is selected

STATUS 1000nnnn 8n

Note off message

DATA 0nnnnnnn nn

Note number

0vvvvvvv vv

Velocity(ignored)

STATUS 1001nnnn 9n

Note on message

DATA 0nnnnnnn nn

Note number

0vvvvvvv vv

Velocity (1-127:on, 0:off)

STATUS 1011nnnn Bn

Control change

DATA 00

Control number (00)

0vvvvvvv vv

Control Value (0-127)

STATUS 1011nnnn Bn

Control change

DATA 20

Control number (32)

0vvvvvvv vv

Control Value (0-127)

STATUS 1011nnnn Bn

Control change

DATA 0nnnnnnn nn

Control number (1-31,33-95,102-119) *

0vvvvvvv vv

Control Value (0-127)

* Numbers 0, 32, and 96–101 cannot be used.

STATUS 1011nnnn Bn

Control change

DATA 01100010 62

NRPN LSB

0vvvvvvv vv

Parameter number LSB

STATUS 1011nnnn Bn

Control change *

DATA 01100011 63

NRPN MSB

0vvvvvvv vv

Parameter number MSB

STATUS 1011nnnn Bn

Control change *

DATA 00000110 06

Data entry MSB

0vvvvvvv vv

Parameter data MSB

STATUS 1011nnnn Bn

Control change *

DATA 00100110 26

Data entry LSB

0vvvvvvv vv

Parameter data LSB

* The STATUS byte of the second and subsequent messages need not

be added during transmission. Reception must occur correctly

whether or not the status byte is omitted.

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual

Reference section

369

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

1.4 PROGRAM CHANGE (Cn)

Reception

If [Program Change ECHO] is ON, bank select messages will also be echoed

from MIDI OUT.

If SINGLE CH is selected, these messages are received if [Program Change RX]

is ON and the [Rx CH] matches. However if [OMNI] is ON, these messages are

received regardless of the channel. When these messages are received, scene

memories are recalled according to the settings of the [Program Change Table].

Transmission

If [Program Change] is ON, these messages are transmitted according to the

[Program Change Table] settings when a scene memory is recalled.

If SINGLE CH is selected, these messages are transmitted on the [Tx CH]

channel.

If the recalled scene has been assigned to more than one program number, the

lowest-numbered program number for each MIDI channel will be transmitted.

Program Change messages are not used for transmission to PM5D Editor

because there is no guarantee that the contents of the assignment tables will

match. (Parameter Change messages are always used.)

You can choose either MULTI MIDI CH or SINGLE CH.

If SINGLE is selected

You can choose the RX CH, OMNI CH, and TX CH.

You can choose whether a bank select message will be added.

A bank of up to 16 can be speciﬁed.

If MULTI is selected

The RX and TX channels will be the same.

The assignment table will use the settings for each MIDI channel. Bank select

messages will not be added.

You can make settings for up to sixteen MIDI channels.

2 SYSTEM REALTIME MESSAGE

2.1 TIMING CLOCK (F8)

Reception

This message is used to control effects. This message is transmitted twenty-four

times per quarter note.

Echoing of this message depends on the OTHER item in the ECHO settings.

2.2 ACTIVE SENSING (FE)

Reception

Once this message has been received, MIDI communication will be initialized

(e.g., Running Status will be cleared) if no message is received for an interval of

400 ms.

This message is not subject to echoing.

2.3 SYSTEM RESET (FF)

Reception

When this message is received, MIDI communication will be initialized (e.g.,

Running Status will be cleared).

This message is not subject to echoing.

3 System Exclusive Message

3.1 Real Time System Exclusive

3.2 Bulk Dump

This message is used to send or receive the contents of various memories stored

within the PM5D.

The basic format is as follows.

The PM5D uses the following data types for a bulk dump.

The unique header (Model ID) identiﬁes whether the device is a PM5D.

To calculate the check sum, add the bytes starting with the byte after BYTE

COUNT (LOW) and ending with the byte before CHECK SUM, take the binary

complement, and set bit 7 to 0.

CHECK SUM = (-sum)&0x7F

Bulk Dumps can be received at any time, and can be transmitted at any time

when a Bulk Dump Request is received.

A Bulk Dump is transmitted on the [Rx CH] channel in response to a Bulk

Dump Request.

In the data portion, seven words of 8-bit data are converted into eight words of

7-bit data.

[Conversion from actual data to bulk data]

d[0. 6]: actual data

b[0. 7]: bulk data

b[0] = 0;

for( I=0; I<7; I++){

if( d[I]&0x80){

b[0] |= 1<<(6-I);

}

b[I+1] = d[I]&0x7F;

}

STATUS 1100nnnn Cn

Program change

DATA 0nnnnnnn nn

Program number (0-127)

STATUS 11111000 F8

Timing clock

STATUS 11111110 FE

Active sensing

STATUS 11111111 FF

System reset

Command rx/tx function

F0 7F dd 06 … F7 MMC COMMAND tx

MMC

command

F0 7F dd 01 … F7 MIDI TIME CODE rx

Full message

Command rx/tx function

F0 43 0n 3E BB BB 0F D0 D1 D2 …

EE F7 BULK DUMP DATA

rx/tx

BULK DUMP

DATA

F0 43 2n 3E 0F D0 D1 D2 … F7 BULK

DUMP REQUEST

BULK DUMP

REQUEST

Data name

(D0)

Data Number

(D1,2)

tx/rx function

‘M’ 0-500

512 (current data)

tx/rx

Scene Memory & Request

‘S’ 512 (current data)

tx/rx

Setup Memory & Request

(current setup)

‘R’ 0–99

512 (current data)

tx/rx

Input patch library & Request

‘O’ 0–99

512 (current data)

tx/rx

Output patch library & Request

‘H’ 1–199

512– (channel

current data)

tx/rx

Input Channel library & Request

‘h’ 1–199

768– (channel

current data)

tx/rx

Output Channel library &

Request

‘G’ 1–199

512– (channel

current data)

tx/rx

Gate library & Request

‘Y’ 1–199

512– (channel

current data)

tx/rx

Compressor library & Request

‘Q’ 1–199

512– (channel

current data)

tx/rx

Input Equalizer library & Request

‘q’ 1–199

768 - (channel

current data)

tx/rx

Output Equalizer library &

Request

‘F’ 1–199

512– (GEQ 1-20

current data)

tx/rx

GEQ Equalizer library & Request

‘E’ 1–199

512– (Effect 1-8

current data)

tx/rx

Effect library & Request

‘W’ 1–199

512 (current data)

tx/rx

HA library & Request

‘P’ 512 (current data)

tx/rx

Program change table & Request

‘C’ 512 (current data)

tx/rx

Control change table & Request

‘N’ 512 (current data)

tx/rx

Plug-in Effect Card Data &

Request

‘A’ 512 (current data)

tx/rx

Event List & Request

MIDI Data Format

370 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

[Recovery from bulk data to actual data]

d[0. 6]: actual data

b[0. 7]: bulk data

for( I=0; I<7; I++){

b[0] <<= 1;

d[I] = b[I+1]+(0x80&b[0]);

}

3.3 PARAMTER CHANGE

Reception

This message is echoed if [Parameter change ECHO] is ON.

This message is received if [Parameter change RX] is ON and [Rx CH] matches

the Device number included in the SUB STATUS. When a parameter change is

received, the speciﬁed parameter will be controlled. When a parameter request

is received, the current value of the speciﬁed parameter will be transmitted as a

parameter change with its Device Number as the [Rx CH].

Transmission

If [Parameter change TX] is ON, and you edit a parameter for which control

change transmission has not been enabled, a parameter change will be

transmitted with the [Tx CH] as its device number.

In response to a parameter request, a parameter change will be transmitted with

[Rx CH] as its device number.

4. PARAMETER CHANGE details

4.1 Current Scene, Setup, Backup, Input Patch,

Output Patch, HA Data

– Parameter change –

4.1.1 Format

Reception

This message is received if [Parameter change RX] is ON and [Rx CH] matches

the Device number included in the SUB STATUS.

This message is echoed if [Parameter change ECHO] is ON.

When the message is received, the speciﬁed parameter will be edited.

Transmission

If [Parameter change Tx] is ON, this message is transmitted with the [Device

Number] speciﬁed by the [Tx CH] when you edit a parameter that is not

assigned in the [Control change assign table].

4.1.2 Data categories

4.2 Current Scene, Setup, Backup, Input Patch,

Output Patch, HA Data

– Parameter request –

4.2.1 Format

Reception

This message is received if [Parameter change RX] is ON and [Rx CH] matches

the Device number included in the SUB STATUS.

This message is echoed if [Parameter change ECHO] is ON.

When this is received, the value of the speciﬁed parameter is transmitted as a

Parameter Change.

4.2.2 Data categories

4.3 Function Call – Library Store/Recall –

(Parameter change)

4.3.1 Format

Reception

This message is received if [Parameter change RX] is ON and [Rx CH] matches

the Device number included in the SUB STATUS.

This message is echoed if [Parameter change ECHO] is ON.

When the message is received, the speciﬁed parameter will be edited.

Transmission

If [Parameter change Tx] is ON, this message is transmitted with a [Device

Number] of the [Tx CH].

Command rx/tx function

F0 43 1n 3E 0F … F7

RARAMETER CHANGE

rx/tx

PM5D native parameter change

F0 43 3n 3E 0F … F7

PARAMETER REQUEST

rx/tx

PM5D native parameter request

STATUS 11110000 F0

System exclusive message

ID No. 01000011 43

Manufacture’s ID number (YAMAHA)

SUB STATUS 0001nnnn 1n

n=0-15 (Device number=MIDI Channel)

GROUP ID 00111110 3E

Digital mixer

MODEL ID 00001111 0F

PM5D

DATA

CATEGORY

00000000 00

OTHER DATA

FUNCTION

NAME

01001100 "L"

(ASCII CODE) See 4.4.2

01101001 "i"

(ASCII CODE)

01100010 "b"

(ASCII CODE)

0fffffff ff

(ASCII CODE)

0fffffff ff

(ASCII CODE)

0fffffff ff

(ASCII CODE)

0fffffff ff

(ASCII CODE)

0fffffff ff

(ASCII CODE)

MODULE NAME 0mmmmmmm mm

(ASCII CODE) See 4.4.3

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

DATA 0mmmmmmm mh

number -source start High

0mmmmmmm ml

number -source start Low

0mmmmmmm mh

number -source end High

0mmmmmmm ml

number -source end Low

0mmmmmmm mh

number -destination start High

0mmmmmmm ml

number -destination to start Low

EOX 11110111 F7

End of exclusive

FUNCTION NAME

Copy “LibCpy__”

Paste “LibPst__”

Clear “LibClr__”

Cut “LibCut__”

Insert “LibIns__”

Edit undo “LibEdtUd”

Function Number Channel tx/rx

MIDI Data Format

372 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

4.4.3 Module names

4.5 Function Call – Library Attribute –

4.5.1 Title (Parameter change) format

Reception

This message is received if [Parameter change RX] is ON and [Rx CH] matches

the Device number included in the SUB STATUS.

This message is echoed if [Parameter change ECHO] is ON.

When the message is received, the title of the speciﬁed memory/library will be

edited.

Transmission

In response to a request, a Parameter Change message is transmitted on the [Rx

CH].

If [Parameter change ECHO] is ON, the message is transmitted without change.

4.5.2 Title (Parameter request) format

Reception

When this is received, a parameter change is transmitted with [Rx CH] as the

device number.

4.5.3 Title module names

4.5.4 Protect (Parameter change) format

4.5.5 Protect (Parameter request) format

Reception

When this is received, a parameter change is transmitted with [Rx CH] as the

device number.

MODULE NAME

SCENE LIB “SCENE___” Copy, Paste, Clear, Cut, Insert,

EditUndo

INPATCH LIB “INPATCH_” Only Clear

OUTPATCH LIB “OUTPATCH” Only Clear

INPUT CHANNEL LIB “INCHNNL_” Only Clear

OUTPUT CHANNEL LIB “OUTCHNNL” Only Clear

INPUT EQ LIB “INEQ____” Only Clear

OUTPUT EQ LIB “OUTEQ___” Only Clear

GATE LIB “GATE____” Only Clear

COMP LIB “COMP____” Only Clear

GEQ LIB “GEQ_____” Only Clear

EFFECT LIB “EFFECT__” Only Clear

HA LIB “HA______” Only Clear

STATUS 11110000 F0

System exclusive message

ID No. 01000011 43

Manufacture’s ID number (YAMAHA)

SUB STATUS 0001nnnn 1n

n=0-15 (Device number=MIDI Channel)

GROUP ID 00111110 3E

Digital mixer

MODEL ID 00001111 0F

PM5D

DATA

CATEGORY

00000000 00

OTHER DATA

FUNCTION

NAME

01001100 "L"

(ASCII CODE)

01101001 "i"

(ASCII CODE)

01100010 "b"

(ASCII CODE)

01010100 "T"

(ASCII CODE)

01101001 "i"

(ASCII CODE)

01110100 "t"

(ASCII CODE)

01101100 "l"

(ASCII CODE)

01011111 "_"

(ASCII CODE)

MODULE NAME 0mmmmmmm mm

(ASCII CODE) See 4.5.3

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

DATA 0mmmmmmm mh

number High

0mmmmmmm ml

number Low

0ddddddd dd

title 1

0ddddddd dd

title x

EOX 11110111 F7

End of exclusive

STATUS 11110000 F0

System exclusive message

ID No. 01000011 43

Manufacture’s ID number (YAMAHA)

SUB STATUS 0011nnnn 3n

n=0-15 (Device number=MIDI Channel)

GROUP ID 00111110 3E

Digital mixer

MODEL ID 00001111 0F

PM5D

DATA

CATEGORY

00000000 00

OTHER DATA

FUNCTION

NAME

01001100 "L"

(ASCII CODE)

01101001 "i"

(ASCII CODE)

01100010 "b"

(ASCII CODE)

01010100 "T"

(ASCII CODE)

01101001 "i"

(ASCII CODE)

01110100 "t"

(ASCII CODE)

01101100 "l"

(ASCII CODE)

01011111 "_"

(ASCII CODE)

MODULE NAME 0mmmmmmm mm

(ASCII CODE) See 4.5.3

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

DATA 0mmmmmmm mh

number High

0mmmmmmm ml

number Low

EOX 11110111 F7

End of exclusive

MODULE NAME number size

SCENE LIB “SCENE___” 0-500,512 (0: response only) 16

INPATCH LIB “INPATCH_” 0-99 (0: response only) 16

OUTPATCH LIB “OUTPATCH” 0-99 (0: response only) 16

INPUT CHANNEL LIB “INCHNNL_” 0-199 (0-1: response only) 16

OUTPUT CHANNEL

LIB

“OUTCHNNL” 0-199 (0-1: response only) 16

INPUT EQ LIB “INEQ____” 1-199 (1-40: response only) 16

OUTPUT EQ LIB “OUTEQ___” 1-199 (1-3: response only) 16

GATE LIB “GATE____” 1-199 (1-4: response only) 16

COMP LIB “COMP____” 1-199 (1-36: response only) 16

GEQ LIB “GEQ_____” 1-199 (1-52: response only) 16

EFFECT LIB “EFFECT__” 0-199 (0: response only) 16

HA LIB “HA______” 0-199 (0: response only) 16

STATUS 11110000 F0

System exclusive message

ID No. 01000011 43

Manufacture’s ID number (YAMAHA)

SUB STATUS 0001nnnn 1n

n=0-15 (Device number=MIDI Channel)

GROUP ID 00111110 3E

Digital mixer

MODEL ID 00001111 0F

PM5D

DATA

CATEGORY

00000000 00

OTHER DATA

FUNCTION

NAME

01001100 "L"

(ASCII CODE)

01101001 "i"

(ASCII CODE)

01100010 "b"

(ASCII CODE)

01010000 "P"

(ASCII CODE)

01110010 "r"

(ASCII CODE)

01110100 "t"

(ASCII CODE)

01100011 "c"

(ASCII CODE)

01011111 "_"

(ASCII CODE)

MODULE NAME 0mmmmmmm mm

(ASCII CODE) See 4.5.6

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

DATA 0mmmmmmm mh

number High

0mmmmmmm ml

number Low

0ddddddd dd

data (unprotected:0, protected:1, read

only:2 )

EOX 11110111 F7

End of exclusive

STATUS 11110000 F0

System exclusive message

ID No. 01000011 43

Manufacture’s ID number (YAMAHA)

SUB STATUS 0011nnnn 3n

n=0-15 (Device number=MIDI Channel)

GROUP ID 00111110 3E

Digital mixer

MODEL ID 00001111 0F

PM5D

DATA

CATEGORY

00000000 00

OTHER DATA

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 373

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

4.5.6 Protect module names

4.5.7 Link format (Parameter change)

Reception

This message is received if [Parameter change RX] is ON and [Rx CH] matches

the Device number included in the SUB STATUS.

This message is echoed if [Parameter change ECHO] is ON.

When the message is received, the link settings of the speciﬁed memory/library

will be edited.

Transmission

In response to a request, a Parameter Change message is transmitted on the [Rx

CH].

If [Parameter change ECHO] is ON, the message is transmitted without change.

4.5.8 Link format (Parameter request)

Reception

When this is received, a parameter change is transmitted with [Rx CH] as the

device number.

For the function and number, refer to the table in 4.5.7.

4.5.9 Library module names

4.5.10 Linked library module names

FUNCTION

NAME

01001100 "L"

(ASCII CODE)

01101001 "i"

(ASCII CODE)

01100010 "b"

(ASCII CODE)

01010000 "P"

(ASCII CODE)

01110010 "r"

(ASCII CODE)

01110100 "t"

(ASCII CODE)

01100011 "c"

(ASCII CODE)

01011111 "_"

(ASCII CODE)

MODULE NAME 0mmmmmmm mm

(ASCII CODE) See 4.5.6

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

DATA 0mmmmmmm mh

number High

0mmmmmmm ml

number Low

EOX 11110111 F7

End of exclusive

MODULE NAME number size

SCENE LIB “SCENE___” 0-500,512 (0:response only) 16

STATUS 11110000 F0

System exclusive message

ID No. 01000011 43

Manufacture’s ID number (YAMAHA)

SUB STATUS 0001nnnn 1n

n=0-15 (Device number=MIDI Channel)

GROUP ID 00111110 3E

Digital mixer

MODEL ID 00001111 0F

PM5D

DATA

CATEGORY

00000000 00

OTHER DATA

FUNCTION

NAME

01001100 "L"

(ASCII CODE)

01101001 "i"

(ASCII CODE)

01100010 "b"

(ASCII CODE)

01010000 "L"

(ASCII CODE)

01101001 "i"

(ASCII CODE)

01101110 "n"

(ASCII CODE)

01101011 "k"

(ASCII CODE)

01011111 "_"

(ASCII CODE)

MODULE NAME 0mmmmmmm mm

(ASCII CODE) See 4.5.9

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

DATA 0sssssss mh

library number High

0sssssss ml

library number Low

0mmmmmmm mm

linked library (ASCII CODE) *1 See 4.5.10

0mmmmmmm mm

linked library (ASCII CODE) *1

0mmmmmmm mm

linked library (ASCII CODE) *1

0mmmmmmm mm

linked library (ASCII CODE) *1

0mmmmmmm mm

linked library (ASCII CODE) *1

0mmmmmmm mm

linked library (ASCII CODE) *1

0mmmmmmm mm

linked library (ASCII CODE) *1

0mmmmmmm mm

linked library (ASCII CODE) *1

0mmmmmmm mh

linked library number High *1

0mmmmmmm ml

linked library number Low *1

0ddddddd dd

data (unlinked:0, linked:1) *1

EOX 11110111 F7

End of exclusive

*1 If this portion is repeated multiple times, this means that a single

packet contains link data for multiple libraries.

STATUS 11110000 F0

System exclusive message

ID No. 01000011 43

Manufacture’s ID number (YAMAHA)

SUB STATUS 0011nnnn 3n

n=0-15 (Device number=MIDI Channel)

GROUP ID 00111110 3E

Digital mixer

MODEL ID 00001111 0F

PM5D

DATA

CATEGORY

00000000 00

OTHER DATA

FUNCTION

NAME

01001100 "L"

(ASCII CODE)

01101001 "i"

(ASCII CODE)

01100010 "b"

(ASCII CODE)

01010000 "L"

(ASCII CODE)

01101001 "i"

(ASCII CODE)

01101110 "n"

(ASCII CODE)

01101011 "k"

(ASCII CODE)

01011111 "_"

(ASCII CODE)

MODULE NAME 0mmmmmmm mm

(ASCII CODE) See 4.5.9

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

DATA 0sssssss mh

library number High

0sssssss ml

library number Low

0mmmmmmm mm

linked library (ASCII CODE) *1 See 4.5.10

0mmmmmmm mm

linked library (ASCII CODE) *1

0mmmmmmm mm

linked library (ASCII CODE) *1

0mmmmmmm mm

linked library (ASCII CODE) *1

0mmmmmmm mm

linked library (ASCII CODE) *1

0mmmmmmm mm

linked library (ASCII CODE) *1

0mmmmmmm mm

linked library (ASCII CODE) *1

0mmmmmmm mm

linked library (ASCII CODE) *1

EOX 11110111 F7

End of exclusive

*1 If this portion does not exist, it is assumed that all information for the

speciﬁed library and number is being requested.

MODULE NAME number

SCENE LIB "SCENE___" 0-500,512 (0:response only)

MODULE NAME number

INPATCH LIB "INPATCH_" 0- 99

OUTPATCH LIB "OUTPATCH" 0- 99

HA LIB "HA______" 0-199

MIDI Data Format

374 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

4.6 Exist Library Range

4.6.1 Format (Parameter change)

Transmission

When PM5D receives Library Exist request command from outside, the answer

will be sent back with the following Parameter change.

This packet shows smallest library number range that exists and not read only.

To p number is requested number or more.

-Example-

SCENE is stored 5,6,7,10,100 and 101

Request Number: 0

Data : Valid, Top Number : 5, End Number 7

Request Number: 8

Data : Valid, Top Number : 10, End Number 10

Request Number: 11

Data : Valid, Top Number : 100, End Number 101

Request Number: 102

Data : Invalid, Top Number : 0, End Number 0

4.6.2 Format (Parameter request)

Reception

The Parameter change will be sent with Device number [Rx CH] immediately

the data is received.

4.6.3 Module name

4.7 Function Call – Collection Store –

4.7.1 Format (Parameter change)

Transmission

Data will be transmitted with the [Device Number] in [Tx CH] when

[Parameter change Tx] is on.

4.7.2 Function name

STATUS 11110000 F0

System exclusive message

ID No. 01000011 43

Manufacture’s ID number (YAMAHA)

SUB STATUS 0001nnnn 1n

n=0-15 (Device number=MIDI Channel)

GROUP ID 00111110 3E

Digital mixer

MODEL ID 00001111 0F

PM5D

DATA

CATEGORY

00000000 00

OTHER DATA

FUNCTION

NAME

01001100 "L"

(ASCII CODE)

01101001 "i"

(ASCII CODE)

01100010 "b"

(ASCII CODE)

01000101 "E"

(ASCII CODE)

01111000 "x"

(ASCII CODE)

01101001 "i"

(ASCII CODE)

01110011 "s"

(ASCII CODE)

01110100 "t"

(ASCII CODE)

MODULE NAME 0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

DATA 0mmmmmmm nn

Data Status ( 0:Invalid data,1:Valid Data )

0nnnnnnn nh

Request Number High

0nnnnnnn nl

Request Number Low

0nnnnnnn nh

Top Number High

0nnnnnnn nl

Top Number Low

0nnnnnnn nh

End Number High

0nnnnnnn nl

End Number Low

EOX 11110111 F7

End of exclusive

STATUS 11110000 F0

System exclusive message

ID No. 01000011 43

Manufacture’s ID number (YAMAHA)

SUB STATUS 0011nnnn 3n

n=0-15 (Device number=MIDI Channel)

GROUP ID 00111110 3E

Digital mixer

MODEL ID 00001111 0F

PM5D

DATA

CATEGORY

00000000 00

OTHER DATA

FUNCTION

NAME

01001100 "L"

(ASCII CODE)

01101001 "i"

(ASCII CODE)

01100010 "b"

(ASCII CODE)

01000101 "E"

(ASCII CODE)

01111000 "x"

(ASCII CODE)

01101001 "i"

(ASCII CODE)

01110011 "s"

(ASCII CODE)

01110100 "t"

(ASCII CODE)

MODULE NAME 0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

DATA 0nnnnnnn nh

Request Number High

0nnnnnnn nl

Request Number Low

EOX 11110111 F7

End of exclusive

MODULE NAME number

SCENE LIB “SCENE___” 1-500

INPATCH LIB “INPATCH_” 1-99

OUTPATCH LIB “OUTPATCH” 1-99

INPUT CHANNEL LIB “INCHNNL_” 2-199

OUTPUT CHANNEL

LIB

“OUTCHNNL” 2-199

INPUT EQ LIB “INEQ____” 41-199

OUTPUT EQ LIB “OUTEQ___” 4-199

GATE LIB “GATE____” 5-199

COMP LIB “COMP____” 37-199

GEQ LIB “GEQ_____” 53-199

EFFECT LIB “EFFECT__” 1-199

HA LIB “HA______” 1-199

Plug-in Effect Library “PLUGIN__” 1-500

STATUS 11110000 F0

System exclusive message

ID No. 01000011 43

Manufacture’s ID number (YAMAHA)

SUB STATUS 0001nnnn 1n

n=0-15 (Device number=MIDI Channel)

GROUP ID 00111110 3E

Digital mixer

MODEL ID 00001111 0F

PM5D/DSP5D

DATA

CATEGORY

00000000 00

OTHER DATA

FUNCTION

NAME

01001100 "C"

(ASCII CODE)

01101001 "o"

(ASCII CODE)

01100010 "l"

(ASCII CODE)

01010101 "U"

(ASCII CODE)

01101110 "n"

(ASCII CODE)

01010011 "S"

(ASCII CODE)

01110100 "t"

(ASCII CODE)

01110010 "r"

(ASCII CODE)

MODULE NAME 0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

DATA 0mmmmmmm mh

number High

0mmmmmmm ml

number Low

0ccccccc ch

channel High

0ccccccc cl

channel Low

EOX 11110111 F7

End of exclusive

Function Number tx/rx

“ColUnStr” Setup 0

User Deﬁned Key 0-3

MIDI Remote 0-3

Fader Mode 0-5

Program Change 0

Control Change 0

Event List 0

In EQ 0-63 *1

Mix EQ 256-279 *2

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 375

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

4.7.3 Module name

4.8 Function Call – Module –

4.8.1 Effect Trigger (Parameter change) format

Reception

This message is received if [Parameter change RX] is ON and [Rx CH] matches

the Device number included in the SUB STATUS. This message is echoed if

[Parameter change ECHO] is ON.

When this message is received, the corresponding effect function will operate

(depends on the effect type).

4.8.2 Effect module names

Nothing will happen if the Effect Type is different.

4.9 Function Call – Channel –

4.9.1 Pair ON/OFF Trigger format (Parameter change)

Reception

Data will be received when [Parameter change Rx] is on and the Device number

of both [Rx CH] and SUB STATUS are matched. The data will be echoed when

[Parameter change ECHO] is on.

4.9.2 Module name – Trigger Type –

Matrix EQ 512-519 *3

Stereo EQ 1024-1027 *4

1280-1299 *8

Gate 0-55 *1

In Comp 0-55 *1

Mix Comp 256- 279 *2

Matrix Comp 512- 519 *3

Stereo Comp 1024-1027 *4

GEQ 0-19 *6

Effect 0-7 *7

Surround 0

*1 0:CH1–47:CH48, 48:STIN1L–55:STIN4R, 56:FXRTN 1L–

63:FXRTN 4R

*2 256:MIX1–279:MIX24

*3 512:MATRIX1–519:MATRIX8

*4 1024:STEREO1L–1027:STEREO2R

*5 Use 512 if the recall-destination or store-source data is

single

*6 0:GEQ1–19:GEQ20

*7 0:Effect1–7:Effect8

*8 1280:GEQ1 – 1299:GEQ20

MODULE NAME

Setup “SETUP___”

User Deﬁned Key “USERDEF_”

MIDI Remote “MIDIRMT_”

Fader Mode “FADMODE_”

Program Change “PRGMCHG_”

Control Change “CTRLCHG_”

Event List “EVNTLIST”

In EQ “IN_EQ___”

Mix EQ “MIX_EQ__”

Matrix EQ “MTRX_EQ_”

Stereo EQ “ST_EQ___”

Gate “GATE____”

In Comp “IN_CMP__”

Mix Comp “MIX_CMP_”

Matrix Comp “MTRX_CMP”

Stereo Comp “ST_CMP__”

GEQ “GEQ_____”

Effect “EFFECT__”

Surround “SURROUND”

STATUS 11110000 F0

System exclusive message

ID No. 01000011 43

Manufacture’s ID number (YAMAHA)

SUB STATUS 0001nnnn 1n

n=0-15 (Device number=MIDI Channel)

GROUP ID 00111110 3E

Digital mixer

MODEL ID 00001111 0F

PM5D

DATA

CATEGORY

00000000 00

OTHER DATA

FUNCTION

NAME

01001101 "M"

01101111 "o"

01100100 "d"

01000110 "F"

01111000 "x"

01010100 "T"

01110010 "r"

01100111 "g"

MODULE NAME 0mmmmmmm mm

(ASCII CODE) See 4.6.2

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

Function Number tx/rx

0mmmmmmm mm

(ASCII CODE)

DATA 0eeeeeee ee

Effect number (0:Effect1 - 7:Effect8)

0ppppppp pp

Release:0, Press:1

EOX 11110111 F7

End of exclusive

MODULE NAME channel

Freeze Play button "FRZPLAY_" 0:Effect1 - 7:Effect8

Freeze Record button "FRZREC__" 0:Effect1 - 7:Effect8

STATUS 11110000 F0

System exclusive message

ID No. 01000011 43

Manufacture’s ID number (YAMAHA)

SUB STATUS 0001nnnn 1n

n=0-15 (Device number=MIDI Channel)

GROUP ID 00111110 3E

Digital mixer

MODEL ID 00001111 0F

PM5D/DSP5D

DATA

CATEGORY

00000000 00

OTHER DATA

FUNCTION

NAME

01000011 "C"

01101000 "h"

01101100 "l"

01010000 "P"

01101001 "i"

01110010 "r"

01000011 "C"

01110000 "p"

MODULE NAME 0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

0mmmmmmm mm

(ASCII CODE)

DATA 0sssssss ss

Source Channel Number H *1

0sssssss ss

Source Channel Number L *1

0ddddddd dd

Destination Channel Number H *1

0ddddddd dd

Destination Channel Number L *1

EOX 11110111 F7

End of exclusive

MODULE NAME

Pair On (with Copy) “PAIRONCP”

Pair On (with Reset Both) “PAIRONRS”

Pair Off “PAIROFF_”

*1 0:CH1–47:CH48

256:MIX1–279:MIX24

512:MATRIX1–519:MATRIX8

MIDI Data Format

376 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

4.10 Level Meter Data – Parameter change –

4.10.1 Format (Parameter change)

Once a Level Meter Request is received to enable transmission, the speciﬁed

meter data will be transmitted at 50 msec intervals for a duration of ten seconds.

If you want meter data to be transmitted continuously, you must transmit a

Request at intervals of no longer than ten seconds.

Reception

This message is echoed if [Parameter change ECHO] is ON.

Transmission

Once transmission is enabled by a Request, the meter data speciﬁed in the

Address will be transmitted on the [Rx CH] channel at a speciﬁc interval for a

speciﬁc duration. (The transmission interval and the duration of transmission

will differ between models of device.)

Tr ansmission is disabled when the power is cycled, or when PORT settings are

changed.

If [Parameter change ECHO] is ON, the message is transmitted without change.

4.10.2 Format (Parameter request)

Reception

This message is received if [Parameter change RX] is ON and [Rx CH] matches

the Device number included in the SUB STATUS. This message is echoed if

[Parameter change ECHO] is ON.

When this is received, the meter data speciﬁed in the Address is transmitted on

the [Rx CH] channel at a speciﬁc interval for a speciﬁc duration.

If this is received with an Address UL = 0x7F, transmission of all meter data will

stop (will be disabled) immediately.

Transmission

If [Parameter change ECHO] is ON, the message is transmitted without change.

4.11 Time Counter Data – Time Code –

4.11.1 Format (Parameter change)

When transmission is enabled by receiving a Remote Time Counter request,

Time Counter data is transmitted at 50 ms intervals for a duration of ten

seconds. If you want counter data to be transmitted continuously, you must

transmit a Request at intervals of no longer than ten seconds.

Reception

This message is echoed if [Parameter change ECHO] is ON.

Transmission

When transmission is enabled by a request, Time Counter data is transmitted

for a speciﬁc duration.

Tr ansmission is disabled when the power is cycled, or when PORT settings are

changed.

If [Parameter change ECHO] is ON, the message is transmitted without change.

4.11.2 Format (Parameter request)

Reception

This message is received if [Parameter change RX] is ON and [Rx CH] matches

the Device number included in the SUB STATUS. This message is echoed if

[Parameter change ECHO] is ON.

When this message is received, Time Counter data is transmitted on the [Rx

CH] channel for a speciﬁc duration.

If a message is received with 0x7F as the second byte of the Address, data

transmission will be stopped (disabled) immediately.

Transmission

If [Parameter change ECHO] is ON, the message is transmitted without change.

STATUS 11110000 F0

System exclusive message

ID No. 01000011 43

Manufacture’s ID number (YAMAHA)

SUB STATUS 0001nnnn 1n

n=0-15 (Device number=MIDI Channel)

GROUP ID 00111110 3E

Digital mixer

MODEL ID 00001111 0F

PM5D

DATA

CATEGORY

00100001 21

REMOTE LEVEL METER

DATA 0mmmmmmm mm

ADDRESS UL

0mmmmmmm mm

ADDRESS LU

0mmmmmmm mm

ADDRESS LL

0ddddddd dd

Data1 H

0ddddddd dd

Data1 L

EOX 11110111 F7

End of exclusive

STATUS 11110000 F0

System exclusive message

ID No. 01000011 43

Manufacture’s ID number (YAMAHA)

SUB STATUS 0011nnnn 3n

n=0-15 (Device number=MIDI Channel)

GROUP ID 00111110 3E

Digital mixer

MODEL ID 00001111 0F

PM5D

DATA

CATEGORY

00100001 21

REMOTE LEVEL METER

DATA 0mmmmmmm mm

ADDRESS UL

0mmmmmmm mm

ADDRESS LU

0mmmmmmm mm

ADDRESS LL

0ccccccc ch

Request Ch Total Number H

0ccccccc cl

Request Ch Total Number L

EOX 11110111 F7

End of exclusive

STATUS 11110000 F0

System exclusive message

ID No. 01000011 43

Manufacture’s ID number (YAMAHA)

SUB STATUS 0001nnnn 1n

n=0-15 (Device number=MIDI Channel)

GROUP ID 00111110 3E

Digital mixer

MODEL ID 00001111 0F

PM5D

DATA

CATEGORY

00101011 2b

Time Counter TC

DATA 0ddddddd dd

Hour

0ddddddd dd

Minute

0ddddddd dd

Second

0ddddddd dd

Frame

EOX 11110111 F7

End of exclusive

STATUS 11110000 F0

System exclusive message

ID No. 01000011 43

Manufacture’s ID number (YAMAHA)

SUB STATUS 0011nnnn 3n

n=0-15 (Device number=MIDI Channel)

GROUP ID 00111110 3E

Digital mixer

MODEL ID 00001111 0F

PM5D

DATA

CATEGORY

00101011 2b

Time Counter TC

DATA 0ddddddd dd

0: Request transmission

0x7F: Request stop transmission

EOX 11110111 F7

End of exclusive

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 377

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

Warning Messages

These are messages displayed in the lower part of the screen. They will disappear after a certain duration has elapsed.

Message Meaning

#xxx of Scene is Empty!

No data has been stored in the scene you attempted to recall, or the data has been damaged so that it

cannot be recalled.

#xxx of Scene is Read Only! You attempted to overwrite (store) a read-only scene.

#xxx of Scene is Protected! You attempted to overwrite (store) a protected scene.

Cannot Undo! You pressed the SCENE MEMORY [UNDO] key when Undo was not available.

Cannot Assign!

You clicked an unavailable (grayed-out) grid in the patch screen, or pressed an invalid key on the panel

(e.g., a DCA/MUTE assign key that is unavailable due to the selected channel).

Cannot Drop! You attempted to drop a EQ/compressor/gate/EQ/effect mini-graph onto a location of a different type.

Pair Made. You used a panel operation to assign channel pairing.

Pair Broken. You used a panel operation to cancel channel pairing.

EFFECT CUE: Turned Off.

CUE was defeated because you switched to another screen from the EQ PARAM or EFFECT ASSIGN

screen, or because you switched the selected effect.

KEY IN CUE: Turned Off.

KEY IN CUE was defeated because you switched from the GATE PRM/COMP PRM screen to a different

screen.

Overwrite Existing Event.

In the EVENT LIST screen you input an event at the same time as a previously-input event, so the exist-

ing event was overwritten.

Event List Full! Last Event cancelled.

In the EVENT LIST screen, the event list is full; the last event in the event list was pushed out and deleted

when you added a new event.

Interval from Previous Event is Too Short!

The event you are attempting to input in the EVENT LIST screen is too close to an existing event earlier

than that location, so it is possible that it may not be recalled at the time you intend.

TIME CODE: Frame Jump!

The time code that was input in the EVENT LIST screen has experienced a frame jump or is running

backward.

TIME CODE: Frame Mismatch!

The incoming time code has a frame rate that is different than the time code speciﬁed in the EVENT LIST

screen.

MIDI: Data Framing Error! Invalid signals are being input to the MIDI IN connector.

MIDI: Data Overrun! Invalid signals are being input to the MIDI IN connector.

MIDI: Rx Buffer Full! Too much data is being received at the MIDI IN connector.

MIDI: Tx Buffer Full! Too much data is being sent from the MIDI OUT connector.

USB: Data Framing Error! Invalid signals are being input from the USB connector input port.

USB: Data Overrun! Invalid signals are being input from the USB connector input port.

USB: Rx Buffer Full! Too much data is being received at the USB connector input port.

USB: Tx Buffer Full! Too much data is being sent from the USB connector output port.

SLOT x: Data Framing Error! Invalid signals are being input from the SLOT x input port.

SLOT x: Data Overrun! Invalid signals are being input from the SLOT x input port.

SLOT x: Rx Buffer Full! Too much data is being received at the SLOT x input port.

SLOT x: Tx Buffer Full! Too much data is being sent from the SLOT x output port.

RS422: Data Framing Error! Invalid signals are being received at the HA REMOTE connector or RS422 REMOTE connector.

RS422: Data Overrun! Invalid signals are being received at the HA REMOTE connector or RS422 REMOTE connector.

RS422: Rx Buffer Full! Too much data is being received at the HA REMOTE connector or RS422 REMOTE connector.

RS422: Tx Buffer Full! Too much data is being transmitted from the HA REMOTE connector or RS422 REMOTE connector.

CASCADE: Data Framing Error! Invalid signals are being input to the CASCADE IN/OUT connector.

CASCADE: Data Overrun! Invalid signals are being input to the CASCADE IN/OUT connector.

CASCADE: Rx Buffer Full! Too much data is being received at the CASCADE IN/OUT connector.

CASCADE: Tx Buffer Full! Too much data is being transmitted from the CASCADE IN/OUT connector.

DME Control: Data Framing Error! Invalid signals are being input during communication with the DME.

DME Control: Data Overrun! Invalid signals are being input during communication with the DME.

DME Control: Rx Buffer Full! Too much data is being received during communication with the DME.

DME Control: Tx Buffer Full! Too much data is being transmitted during communication with the DME.

Wrong Word Clock!

The PM5D cannot synchronize because the source selected by MASTER CLOCK SELECT in the WORD

CLOCK screen is not appropriate.

Sync Error! [xxxx] The xxxx signal is not synchronized with the PM5D.

xxxx No Signal Present! The xxxx signal is not being input.

Data Type Conﬂict! Canceled. You attempted to execute a library recall or channel copy operation on a different type of channel.

HA Type Conﬂict! Data Ignored. You attempted to recall a HA library of a different model (PM5D model or PM5D-RH model).

Conﬂicting GPI OUT Cancelled.

The parameter you assigned to the FADER START function or to a User Deﬁned key is the same as an

existing GPI OUT assignment, so the GPI OUT assignment was cancelled.

Conﬂicting USER DEFINED KEY

Cancelled.

The parameter you assigned to GPI OUT is the same as an existing User Deﬁned key assignment, so the

User Deﬁned key assignment was cancelled.

Conﬂicting FADER START Cancelled.

The parameter you assigned to GPI OUT is the same as an existing FADER START function, so the FADER

START assignment was cancelled.

Wrong Password! The system password or console password you input was incorrect.

System Password Changed. The system password has been changed.

Console Password Changed. The console password has been changed.

Warning Messages

378 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

Parameter Locked. Parameter Lock has been enabled.

Parameter Unlocked. Parameter Lock has been defeated.

This Parameter is Locked. The parameter you attempted to control is locked.

Channel Copied. The selected channel settings were copied to the memory buffer.

Channel Pasted. The channel settings in the memory buffer were pasted to the selected channel.

Nothing to Paste! Paste cannot be performed because there is no data in the memory buffer.

Cannot Paste to Different Channel Type. Paste cannot be performed because you are attempting to paste channel settings of a different type.

No Card in Slot! No memory card is inserted in the MEMORY CARD slot.

File Already Exist!

The memory card already contain a ﬁle/directory with the same name as the one you are attempting to

save, rename, or create.

Saving Aborted. Saving to memory card was aborted.

Loading Aborted. Loading from memory card was aborted.

No Controllable Gain. You attempted to operate a gain knob that is currently disabled on the panel.

Tap Operation Ignored. Tap operation was ignored because the TAP TEMPO button is not displayed in the screen.

Cascade Unit Disconnected. The connection with a cascade-connected external device was broken.

Additional Cascade Unit Detected. A cascade-connected external device was newly detected.

Incorrect Cascade Connection! The connection is not appropriate for the cascade settings.

Couldn’t Store Scene on Slave Console!

The cascade-connected slave console was unable to store the scene because the scene was protected on

the slave console, or for some other reason.

Couldn’t Edit Scene on Slave Console!

The cascade-connected slave console was unable to edit the scene because the scene was protected on

the slave console, or for some other reason.

DME Disconnected. The connection with an external DME was broken.

No Response from External HA. No response from an external AD8HR or AD824.

Processing Aborted. A process was aborted.

Internal Power Supply is Turned On. (DSP5D only) The internal power supply started up normally.

Illegal Address! (DSP5D only) The IP address or gateway address setting is invalid.

Load Locked. LOAD LOCK is on, and ﬁle loading from memory card is prohibited.

Load Unlocked. LOAD LOCK is off, and ﬁle loading from memory card is possible.

DME Unsupported Firmware Version. A DME operating with an unsupported ﬁrmware version was connected.

DME Unsupported Component Version. A DME containing a component of an unsupported version was connected.

DME DSP Power Shortage. The DSP resources of the DME are insufﬁcient.

Corrupted data ﬁxed!

Illegal parameter values that exceeded the valid range have been correct to stay within the allowable

range.

Parameter out of range! While reading from a memory card, there was a parameter value that exceeded the allowable range.

Channel Moved. Channel settings have been moved between the selected channels.

Message Meaning

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 379

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

Error Messages

These are messages displayed as popup windows in the center of the screen. After noting the content of the message, click the

OK button in the screen to close the popup window.

Message Meaning

Cannot Store! Failed to store a scene memory or library.

Cannot Recall! Failed to recall a scene memory or library.

Memory Card Full! You attempted to save a ﬁle that was larger than the available capacity of the memory card.

File Not Found! The ﬁle/directory does not exist on the memory card.

Couldn’t Read File. Failed to read the ﬁle from the memory card.

Couldn’t Write File. Failed to write the ﬁle to the memory card.

Couldn’t Delete File. Failed to delete the memory card ﬁle.

Couldn’t Open File. Failed to open the ﬁle from the memory card.

Couldn’t Close File. Failed to close the ﬁle on the memory card.

Unsupported File Format! The ﬁle you attempted to load from the memory card is of an unsupported format.

No Files to Upload! Internal memory does not contain ﬁles to upload.

Low Battery! The backup battery voltage is low.

Power Supply has Malfunctioned!

A problem has occurred with the PW800W power supply connected to the PM5D. Please contact your

Yamaha dealer.

Total Slot Power Capability Exceeded! The I/O cards installed in the slots exceed the rated power capacity.

Internal Power Supply is Cut Off!

(DSP5D only) Power has stopped being supplied from the internal power supply. Alternatively, some

type of problem has occurred. If a problem has occurred, please contact your Yamaha dealer.

External Power Supply is Cut Off!

(DSP5D only) Power has stopped being supplied from the PW800W power supply connected to the

DSP5D. Alternatively, some type of problem has occurred. If a problem has occurred, please contact

your Yamaha dealer.

Illegal MAC Address! Cannot Use

Ethernet.

(DSP5D only) Because the MAC address setting was damaged for some reason, communication via the

NETWORK connector (RJ-45 connector) is not possible. Please contact your Yamaha dealer.

Power Supply Fan has Malfunctioned!

(DSP5D only) The cooling fan for the internal power supply has stopped. Please contact your Yamaha

dealer.

Right Fan has Malfunctioned! (DSP5D only) The cooling fan on the right side has malfunctioned. Please contact your Yamaha dealer.

Left Fan has Malfunctioned! (DSP5D only) The cooling fan on the left side has malfunctioned. Please contact your Yamaha dealer.

Troubleshooting

380 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

Troubleshooting

Power does not turn on, panel LEDs

and the LCD display do not light

❍ Are the PM5D/DSP5D and PW800W correctly connected by the special power cable?

❍ Is the PW800W’s POWER switch turned on?

❍ In the UTILITY function PREFERENCE 2 screen, could the LED brightness have been turned down?

(➥ p.206)

❍ If the power still does not turn on, contact your Yamaha dealer.

Sound is not input

❍ Is the optional I/O card installed correctly? (➥ p.37)

❍ Is a signal being input from the external device?

❍ Is the input port patched to an input channel? (➥ p.74)

❍ Is the GAIN of the internal head amp or external head amp set to an appropriate level? (➥ p.44, 228)

❍ Is the EQ attenuator raised? (➥ p.286)

❍ Could insert be turned on even though it has not been speciﬁed correctly? (➥ p.78)

❍ Is the [ON] key indicator of the input channel lit?

❍ Is the fader of the input channel raised?

❍ In SOLO mode, could the [CUE] key be on for a channel that has no signal? (➥ p.104)

❍ Is the DCA fader assigned to that channel raised? Could MUTE be turned on? (➥ p.83)

Sound is not output

❍ Is the optional I/O card installed correctly? (➥ p.37)

❍ Is the [ON] key indicator of the STEREO A/B channel lit?

❍ Is an output port patched to the output channel? (➥ p.75)

❍ Could LCR be on, and the CSR value be set to 1.0? (➥ p.267)

Sound is not output from

headphones or the MONITOR OUT

jacks

❍ Is the MONITOR section [PHONES] knob or [LEVEL] knob set to an appropriate volume?

❍ Are on-screen settings such as MONITOR LEVEL and CUE LEVEL set to an appropriate volume?

Sound is not loud enough

❍ Is the GAIN of the internal head amp or external head amp set to an appropriate level? (➥ p.44, 228)

❍ Is the fader of the input channel raised?

❍ Could the EQ gain be set to an extremely low setting? (➥ p.73)

❍ Could the GATE/COMP threshold or ratio be set to an extreme setting? (➥ p.71, 72)

❍ Is the EQ attenuator raised? (➥ p.286)

❍ Is the fader of the output channel raised?

❍ Try using the various screens of the METER function to check the levels. (➥ p.231, 232)

❍ Is the DCA fader assigned to that channel raised?

Sound is distorted

❍ Is the word clock set correctly? (➥ p.38)

❍ Is the GAIN of the internal head amp or external head amp set to an appropriate level? (➥ p.44, 228)

❍ Could the fader of the input channel be raised too high?

❍ Could the fader of the STEREO A/B channel be raised too high?

❍ Could the EQ gain be set to an extremely high setting? (➥ p.73)

Sound is output even though it is not

patched to an output channel

❍ Could you have assigned an input channel to direct out? (➥ p.80)

❍ Could you have assigned an output channel as the insert out? (➥ p.78)

Paired channels are not heard in

stereo

❍ Are the pan mode setting and pan value correct? (➥ p.302)

The volume of a speciﬁc channel

rises and falls

❍ Could GATE/COMP be set to ducking? (➥ p.72)

Operating a fader does not control

the level as you expect

❍ Have you used the layer keys ([CH 1-24]/[CH 25-48] keys or [ST IN 1-4]/[FX RTN 1-4] keys) to select the

appropriate layer?

❍ Is the FADER [FLIP] key turned off?

Only the sound of a speciﬁc channel

is heard from the MONITOR OUT or

PHONES jack

❍ Could a [CUE] key be on?

Noise occurs from an externally

connected recorder or other device

❍ Is the word clock set correctly? (➥ p.38)

❍ Could the input signal be unsynchronized?

❍ Is the dither setting appropriate? (➥ p.229)

❍ Could oscillator or talkback be turned on? (➥ p.106, 107)

High frequency range is attenuated

❍ Could emphasis be applied? This problem will occur if the input signal status does not match the empha-

sis data. (➥ p.220, 237)

❍ Could EQ be applied? (➥ p.73)

An input signal is being input, but

there’s no monitor output

❍ Could the CUE INTERRUPTION button be on? If this button is on, the cue/solo signal will also be output

from the MONITOR OUT jacks while the Cue/Solo function is active. (➥ p.239)

Some channels are always heard

even in SOLO mode

❍ Could those channels be set to SOLO SAFE? (➥ p.241, 242)

Not enough headroom, especially

when EQ boost is applied

❍ Use the EQ attenuator function to lower the level. (➥ p.286)

Sound recorded via a 2TR OUT

DIGITAL jack or a digital I/O card is

gritty

❍ Check that the dither function matches the word length of the recording device. (➥ p.229)

Signal is delayed ❍ Check whether the delay setting for each channel is set correctly. (➥ p.66)

Turning a MIX encoder does not

change the send level to the MIX bus

❍ Is the [MIX SEND] key turned on?

❍ Is the MIX [ON] key turned on?

❍ Is the MIX bus set to VARI type? (➥ p.222)

❍ If the send point is set to POST, could the fader have been lowered?

Can’t save scene memory or library

data

❍ Are you attempting to save the data to a read-only scene/library or a protected scene? (➥ p.175)

Can’t save to a memory card

❍ Is the memory card protected?

❍ Does the memory card have enough free capacity to save the data?

❍ When formatting a memory card, format it in FAT16 format.

Can’t transmit/receive MIDI data

❍ Is the MIDI PORT selected correctly? (➥ p.123, 125, 127)

❍ Are the mode and channel selected correctly on the transmitting and receiving devices? (➥ p.123, 125)

❍ Has an event been assigned for the program change? (➥ p.123)

The [ON] keys or [SEL] keys select

the wrong channels

❍ Have you used the layer keys ([CH 1-24]/[CH 25-48] keys or [ST IN 1-4]/[FX RTN 1-4] keys) to select the

appropriate layer?

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 381

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

General Speciﬁcations

PM5D/PM5D-RH

You paired input channels, but the

signal phase is incorrect

❍ Set the paired input channels to the same phase setting. Even when channels are paired, the phase set-

tings are not linked. (➥ p.53)

When you recall a scene, some

channels/parameters are not

updated

❍ Could those channels/parameters be set to Recall Safe or Selective Recall? (➥ p.92, 94)

You turn on a CUE button in the

EFFECT PARAM screen, but it is

automatically defeated

❍ This is defeated automatically when you switch screens in the display. (➥ p.167)

Can’t make boost settings with the

GEQ

❍ In the GEQ PARAM screen, could LIMIT be set to –24 dB? (➥ p.119)

When you recall a scene, it takes a

certain amount of time for the faders

to stop

❍ Could you have speciﬁed a fade time? (➥ p.95)

The panel LEDs or LCD display are

too dark / too bright

❍ In the UTILITY function PREFERENCE 2 screen, use the BRIGHTNESS setting to adjust the brightness.

(➥ p.206)

Can’t control the DSP5D that’s

cascade-connected to the PM5D

❍ Are the PM5D and DSP5D correctly cascade-connected?

❍ In the SYS/W.CLOCK function MIXER SETUP screen, is CASCADE CONNECTION set to the correct type?

❍ If the units are cascade-connected via the DCU5D, could two Ethernet cables be connected? To allow bi-

directional communication, connect one Ethernet cable between the DCU5D and DSP5D.

❍ Is the DSP5D’s machine ID number set correctly?

❍ In the SYS/W.CLOCK function MIXER SETUP screen, is the setting CASCADE ENABLED?

❍ Have you used a user-deﬁned key or FADER MODE key to select the machine that you want to control

from the PM5D?

MIX channel signal is not sent from

MIX OUT connector

❍ For the output channel, is a MIX channel patched to the MIX OUT jack?

Can’t load from memory card

❍ Is the memory card formatted as FAT16?

❍ In the UTILITY function SECURITY screen, is the LOAD LOCK button turned off?

Sampling Frequency

Internal: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz

External: 44.1 kHz (–10%) to 48 kHz (+6%)

88.2 kHz (–10%) to 96 kHz (+6%)

Signal Delay

PM5D: Less than 2.3 ms INPUT to STEREO A,B (@Fs = 48 kHz)

Less than 1.15 ms INPUT to STEREO A,B (@Fs = 96 kHz)

PM5D-RH: Less than 2.5 ms INPUT to STEREO A,B (@Fs = 48 kHz)

Less than 1.25 ms INPUT to STEREO A,B (@Fs = 96 kHz)

Fader 100mm motorized x38

Fader Resolution +10 to –138, –∞ dB (1024 steps/100 mm)

Maximum Voltage Gain

PM5D: 84 dB INPUT1-48 to Each Output

PM5D-RH: 86 dB INPUT1-48 to Each Output

Crosstalk (@1kHz) –80 dB Adjacent Input Channels (INPUT1-48), GAIN: Min.

Dimensions 1551 x 950 x 283 mm (W x D x H)

Net Weight

PM5D: 98 kg

PM5D-RH: 97 kg

Power Requirements

PM5D: 480W, DC 24V, 20A (Use PW800W Only)

PM5D-RH: 528W, DC 24V, 22A (Use PW800W Only)

Operation free-air Temperature Range +10 °C to +35 °C

Storage Temperature Range –20 °C to +60 °C

Included Accessories

Owner’s Manual

Gooseneck Lamps x 3

Power Supply PW800W Connection Cable

Optional Accessories

mini YGDAI cards

Power Supply PW800W

Power Supply Link Cable PSL120

General Specifications

382 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

❏ Analog Input (1-48)

❏ Analog Input (ST IN1-4 [L,R])

❏ Analog Input (2TR IN ANALOG1,2 [L,R])

❏ Digital Input (2TR IN DIGITAL1-3)

❏ Talkback Input

❏ Oscillator

❏ STEREO A,B [L,R], MIX1-24, MATRIX1-8

❏ MONITOR OUT [L,C,R], CUE OUT

❏ PHONES (x2)

❏ Digital Output (2TR OUT DIGITAL1-3)

Connector XLR-3-31 Type (Balanced) x48

Phantom Power

PM5D: +48V DC is supplied to Input by individual mechanical switch

PM5D-RH: +48V DC is supplied to Input by individual software control

Pad Switch PM5D: 0/26 dB attenuation

Gain Control

PM5D: 44 dB detented

–60 dB to –16 dB (PAD=OFF), –34 to +10 dB (PAD=ON)

PM5D-RH: 72 dB by software control

–62 dB to 10 dB (1 dB step)

Peak Indicator Red LED is lit when post HA level reaches 3 dB below clipping

Signal Indicator Green LED is lit when post HA level reaches 14 dB below nominal

Insert (Pre AD converter) PM5D: Out, In (TRS Balanced)

Insert Switch PM5D: On/Off

AD Converter 24bit linear, 128 times oversampling

Connector XLR-3-31 Type (Balanced) x8

Phantom Power PM5D-RH: +48V DC is supplied to Input by individual software control

Gain Control

PM5D: 44 dB detented

–34 dB to +10 dB

PM5D-RH: 72 dB by software control

–62 dB to +10 dB (1 dB step)

Peak Indicator Red LED is lit when post HA level reaches 3 dB below clipping

Signal Indicator Green LED is lit when post HA level reaches 14 dB below nominal

AD Converter 24bit linear, 128 times oversampling

Connector XLR-3-31 Type (Balanced) x4

Gain Switch +24 dBu (default) / +18 dBu

AD Converter 24bit linear, 128 times oversampling

Connector

AES/EBU XLR-3-31 Type (Balanced) x2 (DIGITAL

IN 1,2)

SPDIF RCA PIN (DIGITAL IN 3)

Sampling Rate

Converter

On/Off by software control (1:3 and 3:1 maxi-

mum input to output sample rate ratio)

Connector XLR-3-31 Type (Balanced)

Phantom Power +48V DC is supplied by software control

Gain 50 dB ﬁxed (pre level control)

AD Converter 24bit linear, 128 times oversampling

Talkback Select

TALKBACK IN and selected INPUT1-48 can be

used simultaneously

Level 0 to –96dB (1dB step)

On/Off Dedicated switch and software control

Waveform

MODE: Sine Wave 1ch, Sine Wave 2ch, Pink

Noise, Burst Noise

Sine Waveform: 100Hz, 1kHz, 10kHz

Routing MIX1-24, MATRIX1-8, STEREO A,B (L,R)

Connector XLR-3-32 Type (Balanced)

DA Converter 24bit linear, 128 times oversampling

Connector XLR-3-32 Type (Balanced)

DA Converter 24bit linear, 128 times oversampling

Level Control Analog potentiometer

Connector TRS

Level Control Analog potentiometer

Connector

AES/EBU XLR-3-32 Type (Balanced) x2 (DIGITAL

OUT 1,2)

SPDIF RCA PIN (DIGITAL OUT 3)

Sampling Rate

Converter

On/Off by software control (1:3 and 3:1 maxi-

mum input to output sample rate ratio)

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 383

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

DSP5D

Sampling Frequency

Internal: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz

External: 42.9975 kHz to 49.200 kHz (Normal Rate)

85.995 kHz to 98.400 kHz (Double Rate)

Signal Delay

Less than 2.5 ms INPUT to OMNI OUT (@Fs=48kHz)

Less than 1.25 ms INPUT to OMNI OUT (@Fs=96kHz)

Maximum Voltage Gain 86 dB INPUT1-48/ST IN1-4 to OMNI OUT1-24

Crosstalk (@1kHz) –80 dB Adjacent Input Channels (INPUT1-48/ST IN1-4), GAIN: Min.

Dimensions 480 x 460 x 440 mm (W x D x H)

Net Weight 38 kg

Power Requirements 300W

AC Power Cord Length 250cm

Operation free-air Temperature Range +10 °C to +35 °C

Storage Temperature Range –20 °C to +60 °C

Included Accessories

Owner’s Manual

AC Power Cord

D-Sub 68-pin Cable 10 m x 2

Optional Accessories

mini YGDAI cards

Power Supply PW800W

Power Supply Link Cable PSL360

Input/output characteristics

384 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

Input/output characteristics

❏ Analog Input Characteristics (PM5D)

❏ Analog Input Characteristics (PM5D-RH)

*1. Sensitivity is the lowest level that will produce an output of +4 dBu (1.23 V) or the nominal output level when the unit is set to maximum gain. (All faders

and level controls are maximum position.)

*2. XLR-3-31 type connectors are balanced. (1=GND, 2=HOT, 3=COLD)

*3. Phone jacks are balanced. (Tip=HOT, Ring=COLD, Sleeve=GND)

*4. There are switches inside the body to preset the maximum input level.

* In these speciﬁcations, 0 dBu = 0.775 Vrms.

* All input AD converters are 24bit linear, 128 times (@48 kHz) oversampling.

* PM5D: +48V DC (phantom power) is supplied to INPUT (1-48) XLR type connectors via each individual switch, and TALKBACK XLR type connectors

via software switch.

PM5D-RH: +48V DC (phantom power) is supplied to INPUT (1-48) and TALKBACK XLR type connectors via master mechanical switch and each individ-

ual software switch.

Input Terminals PAD GAIN

Actual Load

Impedance

For Use With

Nominal

GAIN SW

Input Level

Connector

Sensitivity

Nominal

Max. Before

Clip

INPUT 1-48

–60dB

3kΩ

50-600Ω Mics

600Ω Lines

—

–80 dBu

(0.0775 mV)

–60 dBu

(0.775 mV)

–40 dBu

(7.75 mV)

XLR-3-31 Type

(Balanced)

–16dB

–36 dBu

(12.3 mV)

–16 dBu

(123 mV)

+4 dBu

(1.23 V)

–10 dBu

(245 mV)

+10 dBu

(2.45 V)

+30 dBu

(24.51 V)

ST IN1-4 [L,R] —

–34dB

4kΩ 600Ω Lines —

–54 dBu

(1.55 mV)

–34 dBu

(15.5 mV)

–14 dBu

(155 mV)

XLR-3-31 Type

(Balanced)

10dB

–10 dBu

(245 mV)

+10 dBu

(2.54 V)

+30 dBu

(24.51 V)

INSERT IN 1-48 — 10kΩ 600Ω Lines —

–16 dBu

(123 mV)

+4 dBu

(1.23 V)

+24 dBu

(12.28 V)

Phone Jack (TRS)

(Balanced)

2TR IN ANALOG

1,2 [L,R]

— 10kΩ 600Ω Lines

+24 dB

(default)

–6 dBu

(388 mV)

+4 dBu

(1.23 V)

+24 dBu

(12.28 V)

XLR-3-31 Type

(Balanced)

+18 dB

–12 dBu

(195 mV)

–2 dBu

(0.616 V)

+18 dBu

(6.16 V)

TALKBACK — 3kΩ

50-600Ω Mics

600Ω Lines

—

–60 dBu

(0.775 mV)

–50 dBu

(2.45 mV)

–30 dBu

(24.5 mV)

XLR-3-31 Type

(Balanced)

Input Terminals GAIN

Actual Load

Impedance

For Use With

Nominal

GAIN SW *4

Input Level

Connector

Sensitivity *1 Nominal

Max. Before

Clip

INPUT 1-48

–62dB

3kΩ

50-600Ω Mics

600Ω Lines

—

–82 dBu

(61.6 µV)

–62 dBu

(0.616 mV)

–42 dBu

(6.16 mV)

XLR-3-31 Type

(Balanced)

+10dB

–10 dBu

(245 mV)

+10 dBu

(2.45 V)

+30 dBu

(24.5 V)

ST IN1-4 [L,R]

–62dB

3kΩ

50-600Ω Mics

600Ω Lines

—

–82dBu

(61.6 µV)

–62 dBu

(0.616 mV)

–42 dBu

(6.16 mV)

XLR-3-31 Type

(Balanced)

+10dB

–10 dBu

(245 mV)

+10 dBu

(2.45 V)

+30 dBu

(24.5 V)

2TR IN ANALOG

1,2 [L,R]

— 10kΩ 600Ω Lines

+24 dB

(default)

–6 dBu

(388 mV)

+4 dBu

(1.23 V)

+24 dBu

(12.28 V)

XLR-3-31 Type

(Balanced)

+18 dB

–12 dBu

(195 mV)

–2 dBu

(0.616 V)

+18 dBu

(6.16 V)

TALKBACK — 3kΩ

50-600Ω Mics

600Ω Lines

—

–60 dBu

(0.775 mV)

–50 dBu

(2.45 mV)

–30 dBu

(24.5 mV)

XLR-3-31 Type

(Balanced)

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual

Reference section

385

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

❏

Analog Input Characteristics (DSP5D)

*1. Sensitivity is the lowest level that will produce an output of +4 dBu (1.23 V) or the nominal output level when the unit is set to maximum gain. (all faders

and level controls are maximum position.)

*2. XLR-3-31 type connectors are balanced. (1=GND, 2=HOT, 3=COLD)

* In these speciﬁcations, 0 dBu = 0.775 Vrms.

* All input AD converters are 24bit linear, 128 times (@48 kHz) oversampling.

* +48V DC (phantom power) is supplied to INPUT (1-48) XLR type connectors via one master and each individual software switches.

❏

Analog Output Characteristics (PM5D, PM5D-RH)

*1. XLR-3-32 type connectors are balanced. (1=GND, 2=HOT, 3=COLD)

*2. Phone jacks are balanced. (Tip=HOT, Ring=COLD, Sleeve=GND)

*3. PHONES stereo phone jacks are unbalanced. (Tip=LEFT, Ring=RIGHT, Sleeve=GND)

*4. There are switches inside the body to preset the maximum output level.

*5. INSERT OUTs are only provided for PM5D.

*6. The position of the level control is 10 dB lowered from Max.

* In these speciﬁcations, 0 dBu = 0.775 Vrms.

* All output DA converters are 24bit, 128 times (@48 kHz) oversampling.

❏

Analog Output Characteristics (DSP5D)

*1. XLR-3-32 type connectors are balanced. (1=GND, 2=HOT, 3=COLD)

*2. There are switches inside the body to preset the maximum output level.

* In these speciﬁcations, 0 dBu = 0.775 Vrms.

* All output DA converters are 24bit, 128 times (@48 kHz) oversampling.

Input Terminals

GAIN

Actual Load

Impedance

For Use With

Nominal

Input Level

Connector

Sensitivity

Nominal

Max. before

clip

INPUT 1-48

–62 dB

Ω

50-600

Ω

Mics

600

Ω

Lines

–82 dBu

(61.6 µV)

–62 dBu

(0.616 mV)

–42 dBu

(6.16 mV)

XLR-3-31 type

(Balanced)

+10 dB

–10 dBu

(245 mV)

+10 dBu

(2.45 V)

+30 dBu

(24.5 V)

ST IN 1-4 [L,R]

–62 dB

Ω

50-600

Ω

Mics

600

Ω

Lines

–82 dBu

(61.6 µV)

–62 dBu

(0.616 mV)

–42 dBu

(6.16 mV)

XLR-3-31 type

(Balanced)

+10 dB

–10 dBu

(245 mV)

+10 dBu

(2.45V)

+30 dBu

(24.5 V)

Output

Terminals

Actual Source

Impedance

For Use With

Nominal

GAIN SW

Output Level

Connector

Nominal Max. Before Clip

STEREO A,B [L,R] 75

Ω

600

Ω

Lines

+24 dB (default) +4 dBu (1.23 V) +24 dBu (12.28 V)

XLR-3-32 Type

(Balanced)

+18 dB –2 dBu (616 mV) +18 dBu (6.16 V)

MONITOR OUT

[L,R,C]

Ω

600

Ω

Lines

+24 dB (default) +4 dBu (1.23 V) +24 dBu (12.28 V)

XLR-3-32 Type

(Balanced)

+18 dB –2 dBu (616 mV) +18 dBu (6.16 V)

CUE OUT [L,R] 75

Ω

600

Ω

Lines

+24 dB (default) +4 dBu (1.23 V) +24 dBu (12.28 V)

XLR-3-32 Type

(Balanced)

+18 dB –2 dBu (616 mV) +18 dBu (6.16 V)

MATRIX OUT 1-8 75

Ω

600

Ω

Lines

+24 dB (default) +4 dBu (1.23 V) +24 dBu (12.28 V)

XLR-3-32 Type

(Balanced)

+18 dB –2 dBu (616 mV) +18 dBu (6.16 V)

MIX OUT 1-24 75

Ω

600

Ω

Lines

+24 dB (default) +4 dBu (1.23 V) +24 dBu (12.28 V)

XLR-3-32 Type

(Balanced)

+18 dB –2 dBu (616 mV) +18 dBu (6.16 V)

INSERT OUT 1-48 150

Ω

10k

Ω

Lines — +4 dBu (1.23 V) +24 dBu (12.28 V)

Phone Jack (TRS)

(Balanced)

*2 *5

PHONES (x 2) 15

Ω

Phones

—

75 mW

150 mW

Stereo Phone Jack

(TRS) (Unbalanced)

Ω

Phones

65 mW

150 mW

Output Terminals

Actual Source

Impedance

For Use With

Nominal

GAIN SW

Output Level

Connector

Nominal Max. before clip

OMNI OUT 1-24 75

Ω

600

Ω

Lines

+24 dB

(default)

+4 dBu

(1.23 V)

+24 dBu

(12.28 V)

XLR-3-32 type (Balanced)

+18 dB

–2 dBu

(616 mV)

+18 dBu

(6.16 V)

Input/output characteristics

386 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

❏ Digital Input Characteristics (PM5D, PM5D-RH)

❏ Digital Input Characteristics (DSP5D)

*1. CASCADE (D-Sub 68pin) Max. Cable length: 200 m@48 kHz, 50 m@96 kHz

*2. CASCADE (RJ-45) Max. Cable length is based on EtherSound standard.

❏ Digital Output Characteristics (PM5D, PM5D-RH)

*1. The channel status of 2TR OUT DIGITAL 1,2 is described on page 387.

*2. The channel status of 2TR OUT DIGITAL 3 is described on page 387.

*3. Dither: word length 16/20/24 bit

*4. XLR-3-32 type connectors are balanced. (1=GND, 2=HOT, 3=COLD)

Terminal Format Data Length Level Connector

2TR IN DIGITAL

1 AES/EBU AES/EBU 24bit RS422

XLR-3-31 Type (Balanced)

*1. XLR-3-31 type connectors are balanced. (1=GND, 2=HOT, 3=COLD)

2 AES/EBU AES/EBU 24bit RS422

XLR-3-31 Type (Balanced)

3 COAXIAL IEC-60958 24bit 0.5Vpp/75Ω RCA Pin Jack

CASCADE IN — RS422 D-Sub Half Pitch Connector 68P (Female)

Terminal Format Data Length Level Connector

CASCADE IN

——RS422 D-Sub Half Pitch Connector 68P (Female)

CASCADE IN

——100Base-TX RJ-45

Terminal Format Data Length Level Connector

2TR OUT DIGITAL

1 AES/EBU

AES/EBU

Professional Use

24bit

RS422

XLR-3-32 Type (Balanced)

2 AES/EBU

AES/EBU

Professional Use

24bit

RS422

XLR-3-32 Type (Balanced)

3 COAXIAL

IEC-60958

Consumer Use

24bit

0.5Vpp/75Ω RCA Pin Jack

CASCADE OUT — RS422 D-Sub Half Pitch Connector 68P (Female)

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 387

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

• Channel Status of 2TR OUT DIGITAL 1,2

• Channel Status of 2TR OUT DIGITAL 3

❏ Digital Output Characteristics (DSP5D)

*1. CASCADE (D-Sub 68pin) Max. Cable length: 200 m@48 KHz, 50 m@96 KHz

*2. CASCADE (RJ-45) Max. Cable length is based on EtherSound standard.

byte bit ﬁeld name ﬁxed/variable data description

0 Block Format

ﬁxed

1 professional use

1 Mode 0 audio

2-4 Emphasis 0x4 off

5 Fs Lock 0 lock

6-7 Sampling Frequency variable

0x0 others

0x3 32kHz

0x2 44.1kHz

0x1 48kHz

0-3 Channel Mode

ﬁxed

0x1 2ch mode

4-7 Users Bit Management 0x0 —

0-2 Use of AUX

ﬁxed

0x1 24bits Audio Data

3-7 Source 0x00 —

3 0-7 Multi Channel ﬁxed 0x00 —

0-1 Digital Audio Reference Signal

ﬁxed

0x0

—

2— 0

3-6 Sampling Frequency variable

0x0 others

0x5 88.2kHz

0x4 96kHz

7 Sampling Frequency Scan Flag ﬁxed 0 —

byte bit ﬁeld name ﬁxed/variable data description

0 Block Format

ﬁxed

consumer use

1 Mode audio

2 Copy 1 enabled

3 Emphasis

off

——

1 0-7 Category Code ﬁxed 0x49 Digital Mixer (L=1:original)

0-3 Source Number

ﬁxed 0x0

4-7 Channel Number

0-3 Sampling Frequency variable

0xC 32kHz

0x0 44.1kHz

0x4 48kHz

0x8 —

0x1 88.2kHz

0x5 96kHz

4-5 Fs Accuracy

ﬁxed

0x0 Level II

—0—

40Maximum Audio Sample word length ﬁxed 1 24bits

1-3 Sample Word Length ﬁxed 0x5 24bits

4-7 Original Sampling Frequency variable

0x3 32kHz

0xF 44.1kHz

0xB 48kHz

0x0 —

0xE 88.2kHz

0xA 96kHz

Terminal Format Data Length Level Connector

CASCADE OUT

——RS422 D-Sub Half Pitch Connector 68P (Female)

CASCADE OUT

——100Base-TX RJ-45

Input/output characteristics

388 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

❏ Control I/O Characteristics (PM5D, PM5D-RH)

*1. XLR-3-31 type connectors are balanced. (1/Sleeve=GND, 2/Tip=HOT, 3/Ring=COLD)

*2. 4pin=HOT, 3pin=COLD, Lamp rating 5 W, Voltage control by variable volume

*3. Inputs: 4 channels, Outputs: 12 channels

Input Pin: AD Converter (7bit, 128steps, Voltage Detection Range: 0-5V, Maximum Rating: 5V)

Output Pin: Open Collector (Vmax=12V, Imax/pin=75 mA, GPO1-8: Total Imax=300 mA, GPO9-12: Total Imax=300 mA)

Power Pin: Power Supply (Vp=5V, Imax/2 pin=500 mA)

❏ Control I/O Characteristics (DSP5D)

❏ SLOT 1-4 (PM5D, PM5D-RH)/SLOT 1-2 (DSP5D) Characteristics

Terminal Format Level Connector

TO HOST USB USB 1.1

—

B Type USB Connector

MIDI

MIDI DIN Connector 5PTHRU

OUT

TIME CODE IN SMPTE SMPTE 0.3Vpp(Min)/10.0Vpp(Max), 10kΩ

XLR-3-31 Type (Balanced)

WORD CLOCK

—

TTL/75Ω (ON/OFF)

BNC Connector

OUT TTL/75Ω

GPI

—

D-Sub Connector 25P (Female)

HA REMOTE

RS422

D-Sub Connector 9P (Male)

RS422 REMOTE D-Sub Connector 9P (Female)

KEYBOARD

PS/2 — DIN Connector 6P

MOUSE

LAMP 1,2,3

—

2.5V - 11.5V

XLR-4-31 Type

MEMORY CARD — PCMCIA (Compact Flash)

Terminal Format Level Connector

WORD CLOCK

IN — TTL/75Ω BNC Connector

OUT — TTL/75Ω BNC Connector

Ethernet 10base-T /100Base-TX 10base-T /100Base-TX RJ-45

Card Name Function Input Output

The Number Of Usable Cards

PM5D/PM5D-RH DSP5D

MY4-AD

ANALOG IN

4IN

—

MY8-AD

8IN

—

MY8-AD24

MY8-AD96

MY4-DA

ANALOG OUT —

4OUT

MY8-DA96 8OUT

MY8-ADDA96 ANALOG IN/OUT 8IN 8OUT

MY8-AE

AES/EBU

8IN 8OUT

MY8-AEB

MY8-AE96

MY8-AE96S

MY16-AE 16IN 16OUT

MY8-AT

ADAT

8IN 8OUT

MY16-AT 16IN 16OUT

MY8-TD

TASCAM

8IN 8OUT

MY16-TD 16IN 16OUT

MY16-C

CobraNet 16IN 16OUT

—

MY16-CII

AVIOM16/o-Y1 A-NET 16IN 16OUT

MY16MADI64 MADI 16IN 16OUT

AVY16-ES EtherSound 16IN 16OUT

Waves Y96K Effect & I/O 8IN 8OUT —

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 389

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

Electrical characteristics

PM5D/PM5D-RH

All faders are nominal when measured. Output impedance of signal generator:150ohms

❏ Frequency Response Fs= 44.1 kHz or 48 kHz @20 Hz–20 kHz, referenced to the nominal output level @1 kHz

Fs= 88.2 kHz or 96 kHz @20 Hz–40 kHz, referenced to the nominal output level @1 kHz

❏ Gain Error @1 kHz

❏ Total Harmonic Distortion Fs= 44.1 kHz or 48 kHz

* Total Harmonic Distortion is measured with a 18 dB/octave ﬁlter @80 kHz

❏ Total Harmonic Distortion Fs=88.2 kHz or 96 kHz

* Total Harmonic Distortion is measured with a 18 dB/octave ﬁlter @80 kHz

* GAIN Max. = –60 dBu (PM5D), –62 dBu (PM5D-RH)

Input Output RL Conditions Min. Typ. Max. Unit

INPUT 1-48

STEREO A,B

600Ω

PM5D: GAIN: Max., PAD: Off

PM5D-RH: GAIN: Max.

–1.5

0.0 0.5 dB

MIX OUT

MATRIX OUT

MONITOR OUT

CUE OUT

PHONES 8Ω –3.0

2TR IN ANALOG 1,2

STEREO A,B

600Ω –1.5

MONITOR OUT

Input Output RL Conditions Min. Typ. Max. Unit

INPUT 1-48 STEREO A,B 600Ω

PM5D: Input Level: –60 dBu, GAIN: Max., PAD: Off

PM5D-RH: Input Level: –62 dBu, GAIN: Max.

2.0 4.0 6.0

dBu

PM5D: Input Level: +10 dBu, GAIN: Min., PAD: On

PM5D-RH: Input Level: +10 dBu, GAIN: Min.

2TR IN ANALOG 1,2 STEREO A,B 600Ω Input Level: +4 dBu 2.0 4.0 6.0

Internal OSC

STEREO A,B

600Ω

Full Scale Output

23.5 24.0 24.5

MIX OUT

MATRIX OUT

MONITOR OUT Full Scale Output, MONITOR Level Control: Max.

CUE OUT Full Scale Output, CUE Level Control: Max.

PHONES 8Ω –30 dBFs, PHONES Level Control: Max. –0.5 0 0.5

Input Output RL Conditions Min. Typ. Max. Unit

INPUT 1-48 STEREO A,B 600Ω

PM5D: +4 dBu @20 Hz–20 kHz, GAIN: Max., PAD: Off

PM5D-RH: +4 dBu @20 Hz–20 kHz, GAIN: Max.

0.1

PM5D: +4 dBu @20 Hz–20 kHz, GAIN: Min., PAD: On

PM5D-RH: +4 dBu @20 Hz–20 kHz, GAIN: Min.

0.05

2TR IN ANALOG 1,2 STEREO A,B 600Ω +4 dBu @20 Hz–20 kHz 0.05

Internal OSC

STEREO A,B

600Ω

Full Scale Output @1 kHz

0.02

MIX OUT

MATRIX OUT

MONITOR OUT Full Scale Output @1 kHz, MONITOR Level Control : Max.

CUE OUT Full Scale Output @1 kHz, CUE Level Control: Max.

PHONES 8Ω Full Scale Output @1kHz, PHONES Level Control: Max. 0.2

Input Output RL Conditions Min. Typ. Max. Unit

INPUT 1-48 STEREO A,B 600Ω

PM5D: +4 dBu @20 Hz–40 kHz, GAIN: Max., PAD: Off 0.1

PM5D-RH: +4 dBu @20 Hz–40 kHz, GAIN: Max. 0.12

PM5D: +4 dBu @20 Hz–40 kHz, GAIN: Min., PAD: On

PM5D-RH: +4 dBu @20 Hz–40 kHz, GAIN: Min.

0.05

2TR IN ANALOG 1,2 STEREO A,B 600Ω +4 dBu @20 Hz–40 kHz 0.05

Internal OSC

STEREO A,B

600Ω

Full Scale Output @1 kHz

0.02

MIX OUT

MATRIX OUT

MONITOR OUT Full Scale Output @1 kHz, MONITOR Level Control : Max.

CUE OUT Full Scale Output @1 kHz, CUE Level Control: Max.

PHONES 8Ω Full Scale Output @1kHz, PHONES Level Control: Max. 0.2

Electrical characteristics

390 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

❏ Hum & Noise EIN= Equivalent Input Noise

* Hum & Noise is measured with a 6 dB/octave ﬁlter @12.7 kHz; equivalent to a 20 kHz ﬁlter with inﬁnite dB/octave attenuation.

❏ Dynamic Range

* Dynamic range is measured with a 6 dB/octave ﬁlter @12.7 kHz; equivalent to a 20 kHz ﬁlter with inﬁnite dB/octave attenuation.

❏ Input Indicator Level

❏ Sampling Frequency

Input Output RL Conditions Min. Typ. Max. Unit

INPUT 1-48

STEREO A,B 600Ω

Master fader at nominal level and one INPUT fader at nomi-

nal level.

–128

EIN

dBu

PM5D: Rs= 150Ω, GAIN: Max., PAD: Off –64

PM5D-RH: Rs= 150Ω, GAIN: Max. –62

Master fader at nominal level and one INPUT fader at nomi-

nal level.

PM5D: Rs= 150Ω, GAIN: Min., PAD: On

PM5D-RH: Rs= 150Ω, GAIN: Min.

–81 –76

All INPUT

Master fader at nominal level and all INPUT1-48 faders at

nominal level.

PM5D: Rs= 150Ω, GAIN: Min., PAD: On

PM5D-RH: Rs= 150Ω, GAIN: Min.

–64

2TR IN ANALOG 1,2 STEREO A,B 600Ω

Master fader at nominal level.

Rs= 150Ω

–81 –76

—

STEREO A,B

600Ω

Residual Output Noise, ST Master Off

–86

MIX OUT Residual Output Noise, MIX Master Off

MATRIX OUT Residual Output Noise, MATRIX Master Off

MONITOR OUT Residual Output Noise, MONITOR Level Control Min.

CUE OUT Residual Output Noise, CUE Level Control Min.

PHONES 8Ω Residual Output Noise, PHONES Level Control Min.

Input Output RL Conditions Min. Typ. Max. Unit

INPUT 1-48 STEREO A,B

600Ω

PM5D: AD + DA, GAIN: Min.,

PAD: On

Fs= 44.1/48 kHz 108

PM5D-RH: AD + DA, GAIN: Min. Fs= 88.2/96 kHz 106

—

STEREO A,B

DA Converter 110

MIX OUT

MATRIX OUT

MONITOR OUT

CUE OUT

Input Output Condition Min. Typ. Max. Unit

INPUT 1-48

INSERT OUT

PEAK Red LED: ON 19 21 23

dBu

SIGNAL Green LED: ON –12 –10 –8

ST IN 1-4

PEAK Red LED: ON 19 21 23

SIGNAL Green LED: ON –12 –10 –8

Parameter Conditions Min. Typ. Max. Unit

External Clock Frequency Range

Normal Rate 39.69 50.88

kHz

Double Rate 79.39 101.76

Internal Clock

Frequency

Word Clock : Int 44.1kHz 44.1

Word Clock : Int 48kHz 48

Word Clock : Int 88.2kHz 88.2

Word Clock : Int 96kHz 96

Accuracy

Word Clock : Int 44.1kHz

50 ppm

Word Clock : Int 48kHz

Word Clock : Int 88.2kHz

Word Clock : Int 96kHz

Jitter

Word Clock : Int 44.1kHz

5ns

Word Clock : Int 48kHz

Word Clock : Int 88.2kHz

Word Clock : Int 96kHz

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 391

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

DSP5D

❏ Frequency Response

Fs= 44.1kHz or 48 kHz @20 Hz-20 kHz, referenced to the nominal output level @1 kHz

Fs= 88.2 kHz or 96 kHz @20 Hz-40 kHz, referenced to the nominal output level @1 kHz

❏ Gain Error Fs= 44.1 kHz, 48 kHz, 88.2 kHz or 96 kHz@1 kHz

❏ Total Harmonic Distortion Fs= 44.1 kHz or 48 kHz

* Total Harmonic Distortion is measured with a 18 dB/octave ﬁlter @80 kHz

❏ Total Harmonic Distortion Fs= 88.2 kHz or 96 kHz

* Total Harmonic Distortion is measured with a 18 dB/octave ﬁlter @80 kHz

❏ Hum & Noise Fs= 44.1 kHz, 48 kHz, 88.2 kHz or 96 kHz, EIN=Equivalent Input Noise

* Hum & Noise are measured with a 6 dB/octave ﬁlter @12.7 kHz; equivalent to a 20 kHz ﬁlter with inﬁnite dB/octave attenuation.

Input Output RL Conditions Min. Typ. Max. Unit

INPUT 1-48

OMNI OUT 1-24 600Ω GAIN: Max. –1.5 0.0 0.5 dB

ST IN 1-4

Input Output RL Conditions Min. Typ. Max. Unit

INPUT 1-48

OMNI OUT 1-24 600Ω

Input level: –62 dBu, GAIN: Max. → Output level: +4.0 dBu (Typ.) –2.0 0 +2.0

Input level: +10 dBu, GAIN: Min. → Output level: +4.0 dBu (Typ.) –2.0 0 +2.0

ST IN 1-4

Input level: –62 dBu, GAIN: Max. → Output level: +4.0 dBu (Typ.) –2.0 0 +2.0

Input level: +10 dBu, GAIN: Min. → Output level: +4.0 dBu (Typ.) –2.0 0 +2.0

Internal OSC Full scale output, Output level: +24.0 dBu (Typ.) –0.5 0 +0.5

Input Output RL Conditions Min. Typ. Max. Unit

INPUT 1-48

OMNI OUT 1-24 600Ω

+4 dBu @20 Hz–20 kHz, GAIN: Max 0.1

+4 dBu @20 Hz–20 kHz, GAIN: Min 0.05

ST IN 1-4

+4 dBu @20 Hz–20 kHz, GAIN: Max 0.1

+4 dBu @20 Hz–20 kHz, GAIN: Min 0.05

Internal OSC Full scale output @1 kHz 0.02

Input Output RL Conditions Min. Typ. Max. Units

INPUT 1-48

OMNI OUT 1-24 600Ω

+4 dBu @20 Hz–40 kHz, GAIN: Max 0.12

+4 dBu @20 Hz–40 kHz, GAIN: Min 0.05

ST IN 1-4

+4 dBu @20 Hz–40 kHz, GAIN: Max 0.12

+4 dBu @20 Hz–40 kHz, GAIN: Min 0.05

Internal OSC Full scale output @1 kHz 0.02

Input Output RL Conditions Min. Typ. Max. Unit

INPUT 1-48

OMNI OUT 1-24 600Ω

Rs= 150Ω, GAIN: Max

Master fader at nominal level and one Ch fader at nominal level.

–128

EIN

dBu

(When controlled by PM5D or PM5D Editor) –62

Rs= 150Ω, GAIN: Min

Master fader at nominal level and one Ch fader at nominal level.

(When controlled by PM5D or PM5D Editor)

–81 –76

ST IN 1-4

Rs= 150Ω, GAIN: Max

Master fader at nominal level and one Ch fader at nominal level.

–128

EIN

(When controlled by PM5D or PM5D Editor) –62

Rs= 150Ω, GAIN: Min

Master fader at nominal level and one Ch fader at nominal level.

(When controlled by PM5D or PM5D Editor)

–81 –76

All INPUT

Rs= 150Ω, GAINs: Min

Master fader at nominal level and all ch1-48 in faders at nominal level.

(When controlled by PM5D or PM5D Editor)

–62

— Residual output noise, ST master off. –86

Electrical characteristics

392 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

❏ Dynamic Range

* Dynamic range are measured with a 6 dB/octave ﬁlter @12.7 kHz; equivalent to a 20 kHz ﬁlter with inﬁnite dB/octave attenuation.

❏ Sampling Frequency

Input Output RL Conditions Min. Typ. Max. Unit

INPUT 1-48

OMNI OUT 1-24 600Ω

AD + DA, GAIN: Min

Fs=44.1/48 kHz 108

dBST IN 1-4 Fs=88.2/96 kHz 106

— DA Converter 110

Parameter Conditions Min Typ Max Units

External Clock Frequency Range

Normal Rate 42.9975 49.200

kHz

Double Rate 85.995 98.400

Internal Clock

Frequency

Word Clock: Int 44.1 kHz 44.1

kHz

Word Clock: Int 48 kHz 48

Word Clock: Int 88.2 kHz 88.2

Word Clock: Int 96 kHz 96

Accuracy

Word Clock: Int 44.1 kHz

50 ppm

Word Clock: Int 48 kHz

Word Clock: Int 88.2 kHz

Word Clock: Int 96 kHz

Jitter

Word Clock: Int 44.1 kHz

5ns

Word Clock: Int 48 kHz

Word Clock: Int 88.2 kHz

Word Clock: Int 96 kHz

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual

Reference section

393

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

Mixer Basic Parameters

❏

Libraries

❏

Input Function

❏

Output Function

❏

Processor

Name

Number Total

Scene Memory Preset 1 + User 500 501

Input Patch Library Preset 1 + User 99 100

Output Patch Library Preset 1 + User 99 100

Input Channel Library Preset 1 + User 199 200

Output Channel Library Preset 1 + User 199 200

Input EQ Library Preset 40 + User 159 199

Output EQ Library Preset 3 + User 196 199

GATE Library Preset 4 + User 195 199

COMP Library Preset 36 + User 163 199

Effect Library Preset 55 + User 144 199

GEQ Library Preset 1 + User 199 200

HA Library Preset 1 + User 199 200

Function

Parameter

Phase Normal/Reverse

MS Decode On, S-Gain

Attenuator –96 to +24 dB

HPF

Slope= 12 dB/Oct

Frequency= 20 Hz to 600 Hz

4Band Equalizer

Frequency= 20 Hz to 20 kHz

Gain= –18 dB to +18 dB

Q= 0.10 to 16.0

Low Shelving (Low Band)

High Shelving, LPF (High Band)

Type I/Type II

Insert Insert Point: Pre EQ/Post EQ/Pre Delay/Post Fader

Direct Out

Direct Out Point: Pre HPF/Pre EQ/Pre Fader/Post

Noise Gate

Type: Gate/Ducking

Threshold= –72 (Gate)/–54 (Ducking) dB to 0 dB

Attack= 0 msec to 120 msec

Hold= 0.02 msec to 1.96 sec

Decay= 5 msec to 42.3 sec

Range= –

∞

dB, –69 dB to 0 dB

Key In: Self Pre EQ/Self Post EQ/Mix21-24/

Ch1-STIN4R (8ch block)

Key In Filter: HPF/LPF/BPF

Compressor

Type: Comp/Expander/Compander H/

Compander S

Threshold= –54 dB to 0 dB

Ratio= 1:1 to

∞

Attack= 0 msec to 120 msec

Release= 5 msec to 42.3 sec

Gain= 0 dB to +18 dB

Knee= Hard to 5 (soft)

Input Delay Time= 0.0 msec to 1000 msec

Fader Level: 1024 steps,

∞

, –138 dB to +10 dB

On On/Off

DCA Group 8 Groups

Mute Group 8 Groups

Mix Send

24 sends

Fix/Variable can be set each two mixes

Mix Send Point: Pre EQ/Pre Fader/Post On/Post

TO ST

Level: 1024 steps,

∞

, –138 dB to +10 dB

LCR Pan CSR= 0% to 100%

Surround Pan 3-1, 5.1, 6.1 panning support

Function

Parameter

8Band Equalizer

(Matrix: 4band)

Frequency= 20 Hz to 20 kHz

Gain= –18 dB to +18 dB

Q= 0.10 to 16.0

Low Shelving (Low Band)

High Shelving, LPF (High Band)

Type I/Type II

Insert Insert Point: Pre EQ/Post EQ/Pre Fader/Post On

Compressor

Type: Comp/Expander/Compander H/Com-

pander S

Threshold= –54 dB to 0 dB

Ratio= 1:1 to

∞

Attack= 0 msec to 120 msec

Release= 5 msec to 42.3 sec

Gain= 0 dB to +18 dB

Knee= Hard to 5 (soft)

Input Delay Time = 0.0 msec to 1000 msec

Fader Level: 1024 steps,

∞

, –138 dB to +10 dB

On On/Off

DCA Group 2 Groups

Mute Group 8 Groups

Mix to Matrix

Stereo to Matrix

Matrix Send Point: Pre Fader/Post Fader/Post On

Level: 1024 steps,

∞

, –138 dB to +10 dB

Output Port Att 0 dB to –9 dB

Function Parameter

GEQ 31 bands x 12 systems

Effects Stereo In/Stereo Out multi effector x 8 systems

Pin Assignment

394 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

Pin Assignment

❏ CASCADE IN ❏ CASCADE OUT

❏ HA REMOTE ❏ RS422 REMOTE

2 1334

68 3537 36

Pin Signal Pin Signal

1 GND 35 GND

2 Input 1-2(+) 36 Input 1-2(–)

3 Input 3-4(+) 37 Input 3-4(–)

4 Input 5-6(+) 38 Input 5-6(–)

5 Input 7-8(+) 39 Input 7-8(–)

6 Input 9-10(+) 40 Input 9-10(–)

7 Input 11-12(+) 41 Input 11-12(–)

8 Input 13-14(+) 42 Input 13-14(–)

9 Input 15-16(+) 43 Input 15-16(–)

10 DTR In(+) 44 DTR In(–)

11 RTS Out(+) 45 RTS Out(–)

12 GND 46 GND

13 Word Clock In(+) 47 Word Clock In(–)

14 Word Clock Out(+) 48 Word Clock Out(–)

15 Control In(+) 49 Control In(–)

16 Control Out(+) 50 Control Out(–)

17 GND 51 ID6 In

18 GND 52 ID6 Out

19 Input 17-18(+) 53 Input 17-18(–)

20 Input 19-20(+) 54 Input 19-20(–)

21 Input 21-22(+) 55 Input 21-22(–)

22 Input 23-24(+) 56 Input 23-24(–)

23 Input 25-26(+) 57 Input 25-26(–)

24 Input 27-28(+) 58 Input 27-28(–)

25 Input 29-30(+) 59 Input 29-30(–)

26 Input 31-32(+) 60 Input 31-32(–)

27 ID0 In 61 ID1 In

28 ID2 In 62 ID3 In

29 ID4 In 63 ID5 In

30 ID0 Out 64 ID1 Out

31 ID2 Out 65 ID3 Out

32 ID4 Out 66 ID5 Out

33 MSB In 67 2Ch/Line In

34 FG 68 FG

Pin Signal Pin Signal

1 GND 35 GND

2 Output 1-2(+) 36 Output 1-2(–)

3 Output 3-4(+) 37 Output 3-4(–)

4 Output 5-6(+) 38 Output 5-6(–)

5 Output 7-8(+) 39 Output 7-8(–)

6 Output 9-10(+) 40 Output 9-10(–)

7 Output 11-12(+) 41 Output 11-12(–)

8 Output 13-14(+) 42 Output 13-14(–)

9 Output 15-16(+) 43 Output 15-16(–)

10 DTR Out(+) 44 DTR Out(–)

11 RTS In(+) 45 RTS In(–)

12 GND 46 GND

13 Word Clock Out(+) 47 Word Clock Out(–)

14 Word Clock In(+) 48 Word Clock In(–)

15 Control Out(+) 49 Control Out(–)

16 Control In(+) 50 Control In(–)

17 GND 51 ID6 Out

18 GND 52 ID6 In

19 Output 17-18(+) 53 Output 17-18(–)

20 Output 19-20(+) 54 Output 19-20(–)

21 Output 21-22(+) 55 Output 21-22(–)

22 Output 23-24(+) 56 Output 23-24(–)

23 Output 25-26(+) 57 Output 25-26(–)

24 Output 27-28(+) 58 Output 27-28(–)

25 Output 29-30(+) 59 Output 29-30(–)

26 Output 31-32(+) 60 Output 31-32(–)

27 ID0 Out 61 ID1 Out

28 ID2 Out 62 ID3 Out

29 ID4 Out 63 ID5 Out

30 ID0 In 64 ID1 In

31 ID2 In 65 ID3 In

32 ID4 In 66 ID5 in

33 MSB Out 67 2Ch/Line Out

34 FG 68 FG

Pin Signal Name Pin Signal Name

1 GND 6 RX+

2 RX– 7 Reserved

3 TX– 8 Reserved

4 TX+ 9 GND

5 N.C

Pin Signal Name Pin Signal Name

1 GND 6 GND

2 RX– 7 RX+

3 TX+ 8 TX–

4 GND 9 GND

5 N.C

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 395

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

❏ GPI

*For information on maximum permissible current, refer to the page 388.

❏ DC POWER INPUT

Dimensions

* Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right

to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options

may not be the same in every locale, please check with your Yamaha dealer.

European models

Purchaser/User Information specified in EN55103-1 and EN55103-2.

Inrush Current: 21A (DSP5D only)

Conforms to Environments: E1, E2, E3 and E4

Pin Signal Name Pin Signal Name

1 GPO1 14 GPO2

2 GPO3 15 GPO4

3 GPO5 16 GPO6

4 GPO7 17 GPO8

5 GND 18 GND

6 GND 19 GND

7 GND 20 GND

8 GND 21 +5V

9 +5V 22 GPI1

10 GPI2 23 GPI3

11 GPI4 24 GPO9

12 GPO10 25 GPO11

13 GPO12

12313

25 1416 15

Pin Signal Name Pin Signal Name

1 +24V 13 GND

2 +24V 14 GND

3 +24V 15 GND

4 +24V 16 GND

5 +24V 17 GND

6 +24V 18 GND

7 +24V 19 CAUTION(+)

8 +24V 20 CAUTION(–)

9 +24V 21 DETECT A

10 GND 22 DETECT B

11 GND 23 DETECT GND

12 GND Frame GND

6789

10111213

17181920

Unit: mm

283

271

260

283

271

260

1551

1450

950

865

1551

1450

950

865

PM5D-RHPM5D

430

340 35070

480

2 6.4

460

21.6

DSP5D

13 440

MIDI Implementation Chart

YAMAHA [Digital Mixing Console] Date: 30-Apr-2004

Model: PM5D/PM5D-RH

MIDI Implementation Chart

Version: 1.0

Function... Transmitted Recognized Remarks

Basic

Channel

Default

Changed

1–16

Memorized

Mode

Default

Messages

Altered

**************

1, 3

Memorized

Note

Number

:True Voice

**************

0–127

Velocity

Note On

Note Off

Effect Control

After

Touch

Key’s

Ch’s

Pitch Bend X X

Control

Change

0,32

6,38

98,99

1-31,33-98,

102-119

Bank Select

Data Entry

NRPN LSB,MSB

Assignable Cntrl

Prog

Change :True#

O 0–127

**************

O 0–127

0–500

Assignable

System Exclusive O *1 O *1

System

Common

:Song Pos

:Song Sel

:Tune

System

Real Time

:Clock

:Commands

Effect Control

Aux

Messages

:All Sound Off

:Reset All Cntrls

:Local ON/OFF

:All Notes OFF

:Active Sense

:Reset

Notes

*1: Bulk Dump/Request, Parameter Change/Request, and MMC.

For MIDI remote and event, all messages can be

transmitted.

MTC quarter frame message is recognized.

Mode 1: OMNI ON, POLY

Mode 3: OMNI OFF, POLY

Mode 2: OMNI ON, MONO

Mode 4: OMNI OFF, MONO

O: Yes

X: No

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 397

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

Index

Symbols

ø ................................................... 67

ø/ATT 1-48

................................. 288

ø/ATT STIN/FXRTN

.................. 288

Numerics

2TR I/O ...................................... 237

Accessing a screen ......................... 27

AD IN section

............................... 43

Adjusting the input gain

(PM5D-RH)

............. 162

Adjusting the output gain

............ 162

ADVANCED mode

.............. 212, 216

Analog audio connections

............. 33

Analog output connections

............ 34

Appendices

................................. 317

Assign

ASSIGN MODE section

............ 81

Assigning a name

..................... 30

Assigning MIDI messages

....... 127

GEQ ASSIGN

......................... 173

ATTENUATION

.......................... 67

AUTO CAPTURE

....................... 178

Auto Store function

....................... 91

BASIC mode ........................ 211, 215

Basic operation

.............................. 23

BLANK SKIP

.............................. 176

Block Diagram

........... End of Manual

Boxes

............................................ 23

BPM

........................................... 167

BUSY indicator

........................... 164

Buttons

.................................... 23, 29

Calibrating the GPI IN ports........ 135

Calibration

.................................. 161

Cascade

....................................... 226

BI-DIRECTION

..................... 225

Cascade connections

.............. 153

CASCADE IN PORT SELECT

224

CASCADE MODE

................. 225

CASCADE OUT PORT

SOURCE SELECT

.... 225

Source when cascade connected

................................. 224

CASCADE FROM

....................... 227

CASCADE/Fs

.............................. 163

CH 1-12

...................................... 293

CH 1-24

............................... 283, 295

CH 1-24 layer

................................ 45

CH 13-24

.................................... 293

CH 25-36

.................................... 293

CH 25-48

............................. 283, 295

CH 25-48 layer

.............................. 45

CH 37-48

.................................... 293

CH JOB

................................ 274, 314

CH to MIX

........................... 112, 299

CH VIEW

............................ 270, 311

Channel Library List

.................... 364

CHANNEL SELECT

...................... 66

Channel strip

...................... 45, 47, 61

INPUT channel

........................ 45

ST IN/FX RTN channel

............ 47

STEREO A/B channel

............... 61

Channel structure

.......................... 12

Character palette

........................... 23

COMP LIBRARY

........... 71, 256, 295

COMP LINK ASSIGN

.... 85, 261, 299

COMP PARAM

................... 253, 291

Compressor

............................ 68, 110

Operations

............................... 71

Compressor Library List

.............. 319

Compressor Link

........................... 85

Connecting to a computer

........... 158

Connections

.................................. 31

Analog audio connections

........ 33

Analog output connections

....... 34

Digital input/output connections

................................... 36

Console Lock

.............................. 152

Control change parameter assign-

ments

....................... 343

Control changes

.......................... 125

CSV EXPORT mode

.................... 212

CSV IMPORT mode

................... 216

Cue

............................................... 99

Cue function

.......................... 104

CUE mode

............................. 102

CUE section

...................... 99, 102

Cue/Solo functions

................. 102

Solo function

.......................... 104

CUE FUNCTION

....................... 241

CUE/SOLO

................................. 240

CUE FUNCTION

................... 241

INPUT SOLO SAFE

............... 241

OUTPUT SOLO SAFE

........... 242

SOLO ON/OFF

...................... 240

Cursor

..................................... 23, 27

Daisy-chain connections................ 38

Data Entry

..................................... 24

DCA

............................................. 81

DCA CUE indicator

.................... 164

DCA GROUP ASSIGN

......... 258, 296

DCA Groups

........................... 81, 82

DELAY

.......................................... 66

Digital input/output connections

... 36

Dimensions

................................. 395

DIMM indicator

.......................... 164

DIRECT OUT PATCH

........... 80, 278

DIRECT RECALL

....................... 165

DIRECT RECALL ASSIGN

.......... 177

Direct Recall function

.................... 91

Directly outputting

........................ 80

DISPLAY ACCESS

.................. 24, 27

DISPLAY ACCESS section

........... 165

Distribution box

............................ 38

DITHER

...................................... 229

Divergence

.................................. 146

DME CONTROL

........................ 199

Drag and drop

............................... 26

DSP5D

About the DSP5D

..................... 12

Cascade connections with the

PM5D

......................... 13

Difference with the PM5D

........ 12

Front panel

............................... 21

Initializing

.............................. 160

Rear panel

................................ 22

Specifying the machine ID num-

ber

............................ 153

DSP5D Editor

............................... 13

Dynamics Parameters

.................. 321

Effect Library

Program Change Table

........... 337

Effects

......................................... 111

Basic operations

...................... 114

Editing

................................... 115

EFFECT ASSIGN

.................... 168

EFFECT CUE indicator

.......... 164

EFFECT functions

.................. 166

EFFECT LIBRARY

................. 169

Effect Library List

................... 324

EFFECT PARAM

.......... 112, 113, 115, 166

Effects Parameters

.................. 325

Freeze effect

............................ 117

Inserting into a channel

.......... 113

PLUG-IN

............................... 170

Recalling

................................. 114

Storing

................................... 115

Tap Tempo function

.............. 116

Using via a MIX bus

............... 112

Effects and tempo synchronization

................................. 336

Electrical characteristics

............... 389

Encoder function

........................... 49

Encoder mode

............................. 165

EQ (Equalizer)

...................... 69, 287

Operations

............................... 73

EQ Library List

............................ 317

EQ Link

......................................... 85

EQ LINK ASSIGN

.......... 85, 260, 298

EQ PARAM

.......................... 250, 286

EQ STIN/FXRTN

........................ 287

Error Messages

............................ 379

EVENT indicator

......................... 164

Index

398 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

EVENT LIST............................... 177

AUTO CAPTURE

.................. 178

DISABLE

......................... 163, 177

ENABLE

......................... 163, 177

EVENT RECALL

.................... 178

EVENT TRIGGER

.................. 178

MOVE DOWN

...................... 179

MOVE UP

.............................. 179

Events

.................................. 123, 125

Examples of systems

................ 31, 32

Exchanging the fader and encoder

functions

.................... 49

EXTERNAL CUE indicator

......... 164

External user interface

................... 25

Fade function ................................ 95

FADE TIME

........................... 95, 184

FADER ASSIGN

.......................... 217

Fader calibration

......................... 161

FADER FLIP/ENCODER MODE

section

........................ 48

FADER MODE

........................... 165

FADER MODE section

................ 149

FADER START

........................... 196

FADER VIEW

...................... 273, 314

Faders

..................................... 23, 29

FADING indicator

...................... 164

Features

........................................ 10

Firmware versions

......................... 14

FIX ASSIGN VIEW

..................... 307

FIXED type MIX bus

..................... 52

FRAME RATE

............................. 179

Freeze effect

................................. 117

Front panel

................................... 20

Front panel (DSP5D)

.................... 21

Function Name

........................... 163

Function parameters

................... 164

FX RTN channels 1–4

.................... 42

FX RTN layer

......................... 47, 165

Gain.............................................. 67

Adjusting

............................... 162

Gain reduction

....................... 110

Gate

............................................ 110

Operations

............................... 72

GATE LIBRARY

..................... 72, 294

GATE Library List

....................... 318

GATE PARAM

............................ 289

GEQ

GEQ ASSIGN

......................... 173

GEQ function

......................... 170

GEQ LIBRARY

....................... 174

GEQ PARAM

.................. 118, 170

GEQ module

Expanding

.............................. 119

Patching

................................. 118

Global

............................ 24, 165, 166

EFFECT functions

.................. 166

GEQ function

......................... 170

METER function

.................... 231

MIDI REMOTE function

........ 188

MON/CUE function

............... 234

SCENE function

..................... 175

SYS/W.CLOCK function

........ 219

UTILITY function

.................. 204

GLOBAL PASTE

................... 97, 187

Global Paste function

.................... 97

GPI

............................................. 194

Calibrating

............................. 135

General Purpose Interface

....... 133

GPI IN

................................... 133

GPI IN MONITOR

................ 195

GPI indicator

.......................... 164

GPI OUT

........................ 136, 195

TALLY

............................ 137, 196

USER DEFINED KEYS

........... 137

Graphic EQ

................................. 118

Basic Operations

..................... 119

Group

........................................... 65

Cue and Solo

.......................... 103

Grouping

...................................... 81

ASSIGN MODE section

............ 81

DCA

......................................... 81

HA (Head Amp) ................... 44, 228

HA indicator

............................... 164

HA LIBRARY

............... 230, 249, 285

HORIZONTAL PAIR

............ 53, 221

HPF (High Pass Filter)

................... 69

Operations

............................... 73

I/O card......................................... 36

Indicator

..................................... 164

Initializing

................................... 160

Initializing (DSP5D)

.................... 160

Input

.............................. 24, 165, 277

ø/ATT 1-48

............................ 288

ø/ATT STIN/FXRTN

.............. 288

ø/EQ function

........................ 286

CH 1-12

................................. 293

CH 1-24

.......................... 283, 295

CH 13-24

............................... 293

CH 25-36

............................... 293

CH 25-48

........................ 283, 295

CH 37-48

............................... 293

CH JOB

.................................. 314

CH LIBRARY

......................... 316

CH to MIX

............................. 299

CH VIEW

.............................. 311

COMP LIBRARY

................... 295

COMP LINK ASSIGN

............ 299

COMP PARAM

...................... 291

DCA GROUP ASSIGN

........... 296

DCA/GROUP function

........... 296

DELAY function

..................... 295

DIRECT OUT PATCH

........... 278

......................................... 287

EQ LIBRARY

......................... 289

EQ LINK ASSIGN

.................. 298

EQ PARAM

............................ 286

EQ STIN/FXRTN

................... 287

FADER VIEW

........................ 314

FIX ASSIGN VIEW

................. 307

GATE LIBRARY

..................... 294

GATE PARAM

....................... 289

GATE/COMP function

........... 289

HA LIBRARY

......................... 285

HA/INSERT function

............. 283

INSERT

.................................. 284

INSERT PATCH

.................... 279

INSERT STIN

......................... 284

INSERT/DIRECT OUT POINT

................................. 281

LCR

........................................ 308

M/S

........................................ 311

MIX SEND VIEW

.................. 305

MUTE GROUP ASSIGN

........ 297

NAME

.................................... 282

PAN/ROUTING function

....... 299

PATCH

.................................. 277

PATCH function

.................... 277

PATCH LIBRARY

.................. 283

SIGNAL FLOW

...................... 313

ST IN

............................. 293, 295

STIN/FXRTN

......................... 283

SURR PARAM

....................... 309

SURR VIEW

........................... 310

VIEW function

....................... 311

Input a character

........................... 30

Assigning a name

...................... 30

INPUT CH layer

.......................... 165

Input channel

....... 12, 41, 283, 293, 295

AD IN section

........................... 43

Channel strip

...................... 45, 47

FADER FLIP/ENCODER MODE

section

........................ 48

FX RTN channels 1–4

............... 42

Input channels 1–48

................. 41

ST IN channels 1–4

................... 41

INPUT CUE indicator

................. 164

INPUT DCA/GROUP function

... 296

COMP LINK ASSIGN

............ 299

DCA GROUP ASSIGN

........... 296

EQ LINK ASSIGN

.................. 298

MUTE GROUP ASSIGN

........ 297

INPUT DELAY function

............. 295

Input Gain Reduction

.................. 233

INPUT GATE/COMP function

... 289

COMP LIBRARY

.................... 295

COMP PARAM

...................... 291

GATE LIBRARY

..................... 294

GATE PARAM

....................... 289

Input channel

......................... 293

ST IN

..................................... 293

INPUT GR

.......................... 110, 233

INPUT HA/INSERT function

...... 283

CH 1-24

................................. 283

CH 25-48

............................... 283

HA LIBRARY

......................... 285

Input channel

......................... 283

INSERT

.................................. 284

STIN/FXRTN

......................... 283

INPUT METER

........................... 231

INPUT ø/EQ function

................. 286

ø/ATT 1-48

............................ 288

ø/ATT STIN/FXRTN

.............. 288

.......................................... 287

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 399

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

EQ PARAM ........................... 286

EQ STIN/FXRTN

................... 287

INPUT EQ LIBRARY

............. 289

Input patch

................................... 74

INPUT PATCH function

............ 277

DIRECT OUT PATCH

........... 278

INPUT PATCH LIBRARY

...... 283

INSERT PATCH

.................... 279

INSERT/DIRECT OUT POINT

................................. 281

NAME

................................... 282

INPUT SOLO SAFE

.................... 241

INPUT VIEW function

............... 311

CH JOB

.................................. 314

CH VIEW

.............................. 311

FADER VIEW

........................ 314

INPUT CH LIBRARY

............. 316

SIGNAL FLOW

...................... 313

Input/output characteristics

........ 384

INSERT

...................................... 284

INSERT IN MIX 1-24

.................. 248

INSERT PATCH

............ 78, 244, 279

INSERT POINT

.......................... 246

INSERT STIN

............................. 284

INSERT/DIRECT OUT POINT

.............. 78, 80, 113, 281

Inserting

External device

......................... 77

Internal effect into a channel

.. 113

Insert-out and insert-in

Patching

................................... 78

Internal memory

Initializing

.............................. 160

KEY IN CUE indicator ................ 164

Keyboard

...................................... 25

Knobs

...................................... 23, 29

LATCH....................................... 193

Layer

........................................ 45, 47

[CH 1-24]/[CH 25-48] keys

...... 45

[ST IN 1-4]/[FX RTN 1-4] keys

INPUT CH

............................. 165

ST IN/FX RTN

....................... 165

LCR

..................................... 267, 308

LCR [B] indicator

........................ 164

LCR indicator

............................. 164

LEARN

....................................... 193

Level Diagram

............ End of Manual

LFE

............................................. 146

Library

COMP LIBRARY

................... 295

EFFECT LIBRARY

................. 169

GATE LIBRARY

..................... 294

GEQ LIBRARY

....................... 174

HA LIBRARY

.................. 249, 285

INPUT CH LIBRARY

............. 316

INPUT EQ LIBRARY

............. 289

INPUT PATCH LIBRARY

...... 283

OUTPUT CH LIBRARY

......... 275

OUTPUT PATCH LIBRARY

.. 247

Linking

......................................... 81

ASSIGN MODE section

............ 81

Compressor Link

...................... 85

EQ Link

.................................... 85

LOAD

......................................... 215

ADVANCED mode

................ 216

BASIC mode

.......................... 215

CSV IMPORT mode

.............. 216

....................................... 140

M/S............................................. 311

Major new functionality in PM5D

V2.0

............................ 14

Manual organize

............................ 15

MATRIX channels 1–8

.................. 56

MATRIX section

........................... 63

MATRIX/ST function

.................. 262

LCR

....................................... 267

MATRIX/ST ROUTING

........ 262

MIX to MATRIX VIEW

......... 264

SURR SETUP

......................... 268

MATRIX/STEREO

....... 251, 255, 257

Memory cards

............................. 138

METER function

......................... 231

INPUT GR

............................. 233

INPUT METER

...................... 231

OUTPUT GR

......................... 234

OUTPUT METER

.................. 232

Meter section

....................... 108, 164

Meters

......................................... 108

Metering point

....................... 109

MIDI

........................................... 123

Assigning MIDI messages

....... 127

MIDI events

........................... 132

MIDI remote channels

............ 131

MIDI CTRL CHANGE

......... 125, 191

MIDI Data Format

...................... 368

MIDI EVENT

.............................. 175

MIDI Implementation Chart

....... 396

MIDI indicator

............................ 164

MIDI PGM CHANGE

.......... 123, 190

MIDI REMOTE

................... 127, 192

MIDI REMOTE function

............ 188

DME CONTROL

................... 199

FADER START

...................... 196

GPI

........................................ 194

LATCH

.................................. 193

LEARN

.................................. 193

MMC

.............................. 197, 198

RS422

.............................. 197, 198

TALLY

................................... 196

TRANSPORT

......................... 198

MIDI SETUP

.............................. 188

mini-YGDAI I/O cards

.................. 36

MIX 1-24

..................... 251, 255, 257

MIX channel output signals

........... 60

MIX channels 1–24

........................ 55

MIX section

........................... 57, 164

MIX SEND VIEW

....................... 305

MIX to MATRIX VIEW

.............. 264

MIXER SETUP

...................... 53, 221

PAIR MODE

.......................... 221

MMC

................................... 197, 198

MON/CUE function

.................... 234

2TR I/O

.................................. 237

CUE/SOLO

............................ 240

MONITOR

............................ 238

OSCILLATOR

........................ 236

TALKBACK

........................... 234

Monitor

......................... 99, 101, 238

CUE mode

............................. 102

SOLO mode

........................... 102

MONITOR sections

...................... 99

Mouse

........................................... 25

MOVE DOWN

........................... 179

MOVE UP

................................... 179

MUTE GROUP ASSIGN

...... 259, 297

Mute Groups

........................... 81, 83

MUTE MASTER

......................... 165

NAME.................................. 247, 282

NEXT SCENE/NEXT EVENT

..... 163

NOISE GATE

................................ 67

NRPN parameter assignments

..... 360

OFFSET TIME ............................ 179

Operating section

.......................... 10

Option card

................................... 37

types of I/O card

....................... 36

OSC indicator

............................. 164

OSCILLATOR

.............. 105, 107, 236

Output

........................... 24, 165, 243

CH JOB

.................................. 274

CH LIBRARY

......................... 275

CH VIEW

............................... 270

COMP function

...................... 253

COMP LIBRARY

.................... 256

COMP LINK ASSIGN

............ 261

COMP PARAM

...................... 253

DCA GROUP ASSIGN

........... 258

DCA/GROUP function

........... 258

DELAY function

..................... 257

EQ function

............................ 250

EQ LIBRARY

.......................... 252

EQ LINK ASSIGN

.................. 260

EQ PARAM

............................ 250

FADER VIEW

........................ 273

HA LIBRARY

......................... 249

INSERT function

.................... 248

INSERT IN MATRIX/STE-

REO/MONITOR

...... 248

INSERT IN MIX 1-24

............. 248

INSERT PATCH

.................... 244

INSERT POINT

..................... 246

LCR

........................................ 267

MATRIX/ST function

............. 262

MATRIX/ST ROUTING

......... 262

MATRIX/STEREO

.................. 251, 255, 257

MIX 1-24

................. 251, 255, 257

MIX to MATRIX VIEW

......... 264

MUTE GROUP ASSIGN

........ 259

NAME

.................................... 247

Index

400 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

PATCH.................................. 243

PATCH function

.................... 243

PATCH LIBRARY

.................. 247

SIGNAL FLOW

...................... 272

SURR SETUP

......................... 268

VIEW function

....................... 270

Output channel

....................... 12, 55

Channel strip

............................ 61

MATRIX channels 1–8

............. 56

MATRIX section

...................... 63

MIX channels 1–24

................... 55

MIX section

.............................. 57

STEREO A/B channels

.............. 55

OUTPUT COMP function

.......... 253

COMP LIBRARY

................... 256

COMP PARAM

...................... 253

MATRIX/STEREO

................. 255

MIX 1-24

............................... 255

OUTPUT CUE indicator

............. 164

OUTPUT DCA/GROUP function

................................. 258

COMP LINK ASSIGN

............ 261

DCA GROUP ASSIGN

........... 258

EQ LINK ASSIGN

.................. 260

MUTE GROUP ASSIGN

........ 259

OUTPUT DELAY function

......... 257

OUTPUT EQ function

................ 250

EQ PARAM

............................ 250

MATRIX/STEREO

................. 251

MIX 1-24

............................... 251

OUTPUT EQ LIBRARY

......... 252

Output Gain Reduction

............... 234

OUTPUT GR

....................... 110, 234

OUTPUT INSERT function

........ 248

HA LIBRARY

......................... 249

INSERT IN MIX 1-24

............. 248

OUTPUT METER

....................... 232

Output patch

................................. 75

OUTPUT PATCH function

......... 243

INSERT PATCH

.................... 244

INSERT POINT

..................... 246

NAME

................................... 247

OUTPUT PATCH LIBRARY

.. 247

OUTPUT PORT ATT

................. 229

Output signals from MATRIX

channels

..................... 64

OUTPUT SOLO SAFE

................ 242

OUTPUT VIEW function

............ 270

CH JOB

.................................. 274

CH VIEW

.............................. 270

FADER VIEW

........................ 273

OUTPUT CH LIBRARY

......... 275

SIGNAL FLOW

...................... 272

Overview of the PM5D system

....... 10

PAIR MODE.......................... 53, 221

Pairing

Enabling/disabling

.................... 53

Pairing MIX channels

............... 59

PAN/ROUTING function

........... 299

CH to MIX

............................. 299

FIX ASSIGN VIEW

................ 307

LCR

....................................... 308

M/S

........................................ 311

MIX SEND VIEW

.................. 305

SURR PARAM

....................... 309

SURR VIEW

........................... 310

Panels

............................................ 16

Parameter Lock

........................... 152

Parameters that can be assigned to

control changes

......... 341

Parametric EQ

Basic Operations

..................... 121

PASTE MODE

.............................. 97

Patch

............................................. 74

Patching

Insert-out and insert-in

............ 78

Pattern

........................................ 146

Phantom power

............................. 44

Phase

............................................. 67

Pin Assignment

........................... 394

PM5D Editor

................................. 13

PM5D, PM5D-RH model

.............. 11

Pointer

.......................................... 23

PREFERENCE 1/2

....................... 204

PRESENT TIME

.......................... 163

PREVIEW indicator

...................... 90

PREVIEW mode

........................... 90

Program changes

......................... 123

Rear panel ..................................... 18

Rear panel (DSP5D)

...................... 22

RECALL SAFE

....................... 94, 182

Recall Safe function

....................... 94

Reference section

......................... 163

Remote control

........................... 123

Control changes

..................... 125

MIDI

...................................... 123

MIDI Remote

......................... 127

MIDI remote channels

............ 131

Program changes

.................... 123

Restoring to the default state

.......... 40

RS422

................................... 197, 198

RS422 indicator

........................... 164

SAVE ................................... 138, 211

ADVANCED mode

................ 212

BASIC mode

.......................... 211

CSV EXPORT mode

............... 212

Scene

..................................... 87, 175

Restoring to the default state

..... 40

Scene memory

....................... 87, 163

Auto Store function

.................. 91

Basic operation

......................... 89

BLANK SKIP

.......................... 176

DIRECT RECALL ASSIGN

..... 177

Direct Recall function

............... 91

EVENT LIST

.......................... 177

Fade function

........................... 95

FADE TIME

........................... 184

GLOBAL PASTE

.................... 187

Global Paste function

............... 97

GPI OUT CONTROL

............. 176

MIDI EVENT

......................... 175

PREVIEW mode

....................... 90

Program Change Table

........... 337

RECALL SAFE

........................ 182

Recall Safe function

.................. 94

Recalling

................................... 90

REMOTE TRANSPORT

......... 176

SCENE

................................... 175

SCENE FUNCTION

............... 176

SCENE function

..................... 175

SCENE MEMORY section

........ 88

SELECTIVE RECALL

............. 180

Selective Recall function

............ 92

Storing

..................................... 89

TRACKING RECALL

............. 186

Tracking Recall function

........... 96

Scroll

............................................. 28

Scroll bar

....................................... 24

SECURITY

.................................. 218

Security functions

........................ 151

Console Lock

.......................... 152

Parameter Lock

...................... 152

Selected channel

.................... 65, 164

Editing parameters

.................... 70

SELECTED CHANNEL section

Selecting the word clock master

..... 38

SELECTIVE RECALL

............ 92, 180

Selective Recall function

................ 92

Sending signals

from the MATRIX section to

output jacks

................ 63

from the STEREO A/B chan-

nels to MATRIX buses

. 62

from the STEREO A/B chan-

nels to output jacks

..... 62

to a MIX bus

............................. 51

to MATRIX buses

..................... 58

to the STEREO bus

............. 50, 59

Setup

............................................. 31

Word clock

............................... 38

Shown in the display

.................... 163

SIGNAL FLOW

................... 272, 313

Signals sent

to a VARI type MIX bus

............ 60

to MATRIX buses

..................... 64

Solo function

............................... 104

SOLO indicator

........................... 164

SOLO mode

................................ 102

SOLO ON/OFF

........................... 240

Specifications

............................... 381

Specifying the machine ID number

................................. 153

ST IN

.................................. 293, 295

ST IN channels 1–4

........................ 41

ST IN layer

............................ 47, 165

START OFFSET button

............... 185

START TIME

.............................. 179

STEREO

........................................ 68

STEREO A/B channels

................... 55

STEREO B

................................... 222

STIN/FXRTN

.............................. 283

Surround

SURR PARAM

....................... 309

SURR SETUP

......................... 268

PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 401

Information shown

in the display

Function

Global

functions

Output

functions

Input

functions

Appendices

SURR VIEW .......................... 310

Surround mode

............ 142, 143, 222

Surround pan

....................... 142, 222

Divergence

............................. 146

LFE

........................................ 146

Notes

..................................... 147

Pattern

................................... 146

Surround buses

...................... 143

Synchronization

............................ 15

SYS/W.CLOCK function

............. 219

CASCADE

............................. 226

DITHER

................................ 229

HA (Head Amp)

.................... 228

HA LIBRARY

......................... 230

MIXER SETUP

...................... 221

OUTPUT PORT ATT

............ 229

WORD CLOCK

..................... 219

Tabs....................................... 23, 164

TALKBACK

................. 105, 106, 234

TALKBACK/OSCILLATOR sections

................................. 105

TALLY

........................................ 196

TAP TEMPO

BPM

...................................... 167

Tap Tempo function

................... 116

Tapping

........................................ 26

TB indicator

................................ 164

TIME CODE

........................ 163, 179

TIME CODE SETUP

................... 179

Top panel

...................................... 16

TRACKING indicator

................. 164

TRACKING RECALL

............. 96, 186

Tracking Recall function

................ 96

TRANSPORT

.............................. 198

Troubleshooting

.......................... 380

USB

USB TO HOST connector

...... 158

USE AS CENTER BUS

......... 222, 239

USE AS STEREO BUS

.......... 222, 239

USER DEFINE

............................ 208

USER DEFINED KEY BANK

...... 165

USER DEFINED KEYS

......... 148, 196

USER DEFINED section

.............. 148

User interface

................................ 23

Using an internal effect via a MIX

bus

........................... 112

UTILITY function

....................... 204

FADER ASSIGN

..................... 217

LOAD

.................................... 215

PREFERENCE 1/2

.................. 204

SAVE

..................................... 211

SECURITY

............................. 218

USER DEFINE

....................... 208

VARI type MIX bus....................... 52

VERTICAL PAIR

................... 53, 221

Warning Messages....................... 377

Word clock

...................... 15, 38, 219

Index

402 PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section

MEMO

PM5D/PM5D-RH Block Diagram

DSP5D Block Diagram

CH 1(...48)

ATT

INPUT

DELAY

CUE

PreEQ/

PreFader/

PostON

DIRECT OUT

Keyin

Self Pre EQ/

Self Post EQ/

Mix21-24 /

CH1-8 Post EQ/

CH9-16 Post EQ/

...

CH41-48 Post EQ

LINK ON/OFF

PAN

HPF

TO ST

MIX1-24

ST A

LEVEL/

DCA1-8

MIX1

MIX24

FIX

VARI

MIX2

Keyin

Self Pre EQ/

Self Post EQ/

Mix21-24/

CH1-8 Post EQ/

CH9-16 Post EQ/

...

CH41-48 Post EQ

LINK ON/OFF

MIX PAIR

FIXED MIX PAN

PFL/

AFL/

Post PAN

KEYIN CUE

INSERT

INSERT IN

INSERT OUT

PreEQ/

PostEQ/

PreDelay/

PostFader

CUE R

CUE L

CASCADE OUT D-SUB

To CASCADE IN/OUT RJ-45

INPUT/

OUTPUT/

DCA

TRIM

GEQ 1(...12)

INSERT OUT

INSERT IN

31BAND

GEQ

METERMETER

ST IN 1-4

Pair configuration of Mono channel

METER

LEVEL/

DCA7-8

BAL

INSERT INSERT

INSERT

OUTPUT

DELAY

INSERT

to MATRIX

To OUTPUT PATCH

MONO

To OUTPUT PATCH

INSERT

PAN

MIX to STEREO

LEVEL/

DCA7-8

PreFader/

PostFader/

PostON

INSERT INSERT

OUTPUT

DELAY

INSERT

Same as the mix master 1

to MATRIX

To OUTPUT PATCH

METER

CUE

PAN

TO ST

LEVEL/D

CA1-8

MIX1

MIX24

FIX

VARI

MIX2

MIX PAIR

FIXED MIX PAN

PFL/

AFL/

POST PAN

MATRIX3

MATRIX4

MATRIX5

MATRIX6

MATRIX7

MATRIX8

MATRIX2

MATRIX1

INSERT

OUTPUT

DELAY

Same as the above

STEREO B-L

STEREO B-R

STEREO A-L

STEREO A-R

LEVEL

MIX1

MIX24

Same as the matrix master 1

To OUTPUT PATCH

Pre EQ/

PreFader/

PostON

SLOT1

DITHER

SLOT2

DITHER

OUTPUT PATCH

SLOT1 16

SLOT2

Same as the monaural input

Same as the stereo master A

TALKBACK

To OUTPUT PATCH

LEVEL

To OUTPUT PATCH

Same as the above

IN 1-48

CUE OUT

DELAY

CUE OUT

DELAY

CUE

Same as the stereo master L

To OUTPUT PATCH

MONO

METER

BYPASS

OSC(L)

OSC(R)

Pink Noise

MS-

DECODE

POST

TO ST

ST B

(C)

CUE

To OUTPUT PATCH

PAN

POST

TO ST

CUE

LCR

CSR

LCR

CSR

Keyin

Self Pre EQ/

Self Post EQ/

Mix21-24 /

Stereo A,B,Matrix1-8 Post EQ

LINK ON/OFF

Keyin

Self Pre EQ/Self Post EQ/Mix21-24 /

Mix1-12 Post EQ/Mix13-24 Post EQ

LINK ON/OFF

Keyin

Self Pre EQ/

Self Post EQ/

Mix21-24 /

Stereo A,B,Matrix1-8 Post EQ

LINK ON/OFF

PAN

BI DIRECTION

From

CASCADE IN

SELECT

BI DIRECTION

From

CASCADE IN

SELECT

PreFader/

PostFader/

PostON

LCR

CSR

ATT

METER

HPF

OUT ATT.

PreATT

METER

InsertIn

METER

4BAND

OUT

METERMETER

GATE COMP

Keyin Filter

OUT

METER

OUT

METER

KEYIN

INSERT

METER

PostFader

PostON

4BAND

OUT

METERMETER

PreATT

METER

PostFader

PostON

TALKBACK

SELECT

SPECTRUM

ANALYZER

8BAND

OUT

METERMETER

METER

KEYIN

METER

OUT

COMP

8BAND

OUT

METERMETER

METER

KEYIN

METER

OUT

COMP

4BAND

OUT

METERMETER

KEYIN

METER

OUT

COMP

METER

PostFader

PostON

PostDelay

PostFader

PostON

PostDelay

METER

PostFader

PostON

PostDelay

CASCADE

OUT

ON/OFF

Lch

METER

Rch

METER

INPUT

+48V

TO TALKBACK SELECT

GAIN

OFF

+48V MASTER

OFF

INPUT 1-48

FX7 OUT L/R

FX8 OUT L/R

FX1 OUT L/R

FX4 OUT L/R

FX6 OUT L/R

FX2 OUT L/R

FX3 OUT L/R

FX5 OUT L/R

INPUT PATCH

SLOT1

SLOT2

FX7 IN L/R

FX8 IN L/R

FX1 IN L/R

FX4 IN L/R

FX6 IN L/R

FX2 IN L/R

FX3 IN L/R

FX5 IN L/R

EFFECT

1-8

EFFECT

MIX 1~24

INSERT OUT

SELECT

METER

SLOT1 1-16

SLOT2 1-16

To BUS SUMMING

CASCADE IN D-SUB

CASCADE IN SELECT

GAIN

OFF

GAIN

OFF

ST IN L

ST IN R

ST IN 1-4 L

ST IN 1-4 R

[INPUT]

(1-48)

x 48

[ST IN]

(1-4)

x 4

PreFader

LEVEL/

DCA7-8

PreFader

To METER

PreATT

PreGate

PreATT

To METER

PreEQ

To METER

PreEQ

To METER

PreEQ

INSERT OUT

PreEQ/

PostEQ/

PreFader/

PostOn

INSERT OUT

PreEQ/

PostEQ/

PreFader/

PostOn

INSERT OUT

PreEQ/

PostEQ/

PreFader/

PostOn

PreGate

TB OUT

OSC OUT

To OUTPUT PATCH

PreEQ

PreHPF

PreFader

PostON

To OUTPUT PATCH

Burst Noise

HPF LPF

INSERT

PFL/

PostON

PFL/

PostON

PreON/

PostON

PFL/

PostON

CASCADE

ON/OFF

FX RTN 1-4

Pair configuration of Mono channel

External CUE

SELECT

SLOT1-2(1-16)

+48V

TO TAL KBA CK

PreATT

STEREO B

MATRIX1-8

MIX1-24

DIRECT OUT 1-STIN-4R

INSERT OUT

STEREO A

OSC OUT(Lch)

TB OUT

CUE L,R

OMNIOUT

STEREO B

MATRIX1-8

MIX1-24

INSERT OUT

STEREO A

OSC OUT(Lch)

TB OUT

CUE L,R

CASCADE IN RJ-45

To External

CUE SELECT

SLOT3 1-16

SLOT4 1-16

DITHER

SLOT3 16

SLOT4

CASCADE OUT RJ-45

From CASCADE OUT

From CASCADE IN SELECT

STEREO A-L

STEREO A-R

STEREO B-L

STEREO B-R

MIX 1

MIX 24

MATRIX 1

MAT

CUE

RIX 8

[OMNI OUT](1-24)

DIM

GITA L

CUE

LEV EL

To OUTPUT PATCH

PM5D Level Diagram

Max. DSP Noise Floor

PHASE

GATE

Digital Clipping Level

Max. Output

Digital

Bit

-10

-20

-30

-40

-50

-60

-70

-80

-90

-100

-110

-120

-130

-140

-150

-160

-170

-190

-200

-210

dBu

Analog

dBFS

-180

[0dBu = 0.775Vrms]

[0dBFS = Full Scale]

+20

+10

-10

-20

-30

-40

-50

-60

-70

-80

-90

-100

-110

-120

-130

-140

-150

-160

+24

-170

-180

-190

[+10dBu]

Nominal

Input

DigitalAnalog Digital Analog

ATT. INSERT

COMP DELAY

PAN

DELAY

BUS

Adder

COMP

MASTER

LEVEL ON

MASTER

INSERT INSERT INSERT

INSERT INSERT BAL

OUTPUT

PATCH

INPUT

PATCH

[+4dBu]

HPF

DECDE

MS-

LEVEL

DCA

INSERT INSERT

dBu

Analog

+20

+10

-10

-20

-30

-40

-50

-60

-70

-80

-90

-100

-110

-120

-130

-140

-150

-160

+24

-170

-180

-190

Nominal Output

[+24dBu]

[+4dBu]

OUT

DCA

OUT

(x2)(x8/4)(x8)(x4)

INSERT IN

INININ

OUT OUT OUT

+30

Nominal Output

(75mW@8 )

(150mW@8 )

Max Output

[The position of the level

control is 10dB lowered

from Max]

PHONES

MONITOR OUT[L,R,C]

STEREO A,B[L,R]

CUE OUT[L,R]

MATRIX OUT1-8

MIX OUT1-24

default setting

INSERT OUT 1-48

GAIN

PAD

INPUT 1-48 (GAIN MIN.,PAD ON)

ST IN (GAIN MIN.)

InputMax. [+30dBu]

InputMax. [+24dBu]

Nominal

Input

InputMax. [-14dBu]

[-34dBu]

Nominal Input

InputMax.

[-40dBu]

[-60dBu]

Nominal

Input

INSERT IN 1-48

2TR IN ANALOG 1,2 [L,R] (default setting)

ST IN (GAIN MAX.)

INPUT 1-48 (GAIN MAX.,PAD OFF)

TALKBACK

InputMax.

[-30dBu]

[-50dBu]

Nominal Input

CASCADE OUT*1CASCADE IN*1

*1 CASCADE TYPE = PM5D - PM5D,

PM5D - DSP5D

*2 CASCADE TYPE = PM5D - DCU5D --- DCU5D - PM5D,

PM5D - DCU5D --- DSP5D,

PM5D - DSP5D - DSP5D,

PM5D - DCU5D --- DSP5D - DSP5D,

PM5D - DCU5D --- DSP5D - DCU5D --- DSP5D

CASCADE OUT*2

CASCADE IN*2

PM5D-RH Level Diagram

Max. DSP Noise Floor

PHASE

GATEAD

Digital Clipping Level

Max. Output

Digital

Bit

-10

-20

-30

-40

-50

-60

-70

-80

-90

-100

-110

-120

-130

-140

-150

-160

-170

-190

-200

-210

GAIN

dBu

Analog

dBFS

-180

[0dBu = 0.775Vrms]

[0dBFS = Full Scale]

+20

+10

-10

-20

-30

-40

-50

-60

-70

-80

-90

-100

-110

-120

-130

-140

-150

-160

+24

-170

-180

-190

Input

Max.

[+30dBu]

[+10dBu]

[-62dBu]

[-42dBu]

Nominal

Input

Nominal

Input

DigitalAnalog

InputMax.

Digital Analog

ATT. INSERT

COMP DELAY

PAN

DELAY

BUS

Adder

COMP

MASTER

LEVEL ON

MASTER

INSERT INSERT INSERT

INSERT INSERT BAL

OUTPUT

PATCH

INPUT

PATCH

HPF

DECDE

MS-

LEVEL

DCA

INSERT INSERT

dBu

Analog

+20

+10

-10

-20

-30

-40

-50

-60

-70

-80

-90

-100

-110

-120

-130

-140

-150

-160

+24

-170

-180

-190

Nominal Output

[+24dBu]

[+4dBu]

STEREO A,B[L,R]

MONITOR OUT[L,R,C]

CUE OUT[L,R]

OUT

DCA

OUT

(x2)(x8/4)(x8)(x4)

INSERT IN

INININ

OUT OUT OUT

+30

MATRIX OUT1-8

MIX OUT1-24

default setting

Nominal Output

(75mW@8 )

(150mW@8 )

Max Output

[The position of the level

control is 10dB lowered

from Max]

PHONES

INPUT 1-48 (GAIN MIN.)

ST IN (GAIN MIN.)

2TR IN ANALOG 1,2 [L,R] (default setting)

INPUT 1-48 (GAIN MAX.)

ST IN (GAIN MAX.)

TALKBACK

InputMax. [+24dBu]

[+4dBu]

Nominal

Input

[-50dBu]

Nominal

Input

[-30dBu]InputMax.

CASCADE OUT*1CASCADE IN*1

*1 CASCADE TYPE = PM5D - PM5D,

PM5D - DSP5D

*2 CASCADE TYPE = PM5D - DCU5D --- DCU5D - PM5D,

PM5D - DCU5D --- DSP5D,

PM5D - DSP5D - DSP5D,

PM5D - DCU5D --- DSP5D - DSP5D,

PM5D - DCU5D --- DSP5D - DCU5D --- DSP5D

CASCADE OUT*2

CASCADE IN*2

DSP5D Level Diagram

Max. DSP Noise Floor

PHASE

GATEAD

Digital Clipping Level

Max. Output

Digital

Bit

-10

-20

-30

-40

-50

-60

-70

-80

-90

-100

-110

-120

-130

-140

-150

-160

-170

-190

-200

-210

GAIN

dBu

Analog

dBFS

-180

[0dBu = 0.775Vrms]

[0dBFS = Full Scale]

+20

+10

-10

-20

-30

-40

-50

-60

-70

-80

-90

-100

-110

-120

-130

-140

-150

-160

+24

-170

-180

-190

Input

Max.

[+30dBu]

[+10dBu]

[-62dBu]

[-42dBu]

Nominal

Input

Nominal

Input

DigitalAnalog

InputMax.

Digital Analog

ATT. INSERT

ONCOMP DELAY

PAN

DELAY

BUS

Adder

COMP

MASTER

LEVEL ON

MASTER

INSERT INSERT INSERT

INSERT INSERT BAL

OUTPUT

PATCH

INPUT

PATCH

HPF

DECDE

MS-

LEVEL

DCA

INSERT INSERT

dBu

Analog

+20

+10

-10

-20

-30

-40

-50

-60

-70

-80

-90

-100

-110

-120

-130

-140

-150

-160

+24

-170

-180

-190

OUT

DCA

OUT

(x2)(x8/4)(x8)(x4)

INSERT IN

INININ

OUT OUT OUT

+30

OMNI OUT1-24

default setting

INPUT 1-48 (GAIN MIN.)

ST IN (GAIN MIN.)

INPUT 1-48 (GAIN MAX.)

ST IN (GAIN MAX.)

CASCADE OUT*1CASCADE IN*1

*1 CASCADE TYPE = PM5D - PM5D,

PM5D - DSP5D

*2 CASCADE TYPE = PM5D - DCU5D --- DCU5D - PM5D,

PM5D - DCU5D --- DSP5D,

PM5D - DSP5D - DSP5D,

PM5D - DCU5D --- DSP5D - DSP5D,

PM5D - DCU5D --- DSP5D - DCU5D --- DSP5D

CASCADE OUT*2

CASCADE IN*2

Nominal Output

[+24dBu]

[+4dBu]

For details of products, please contact your nearest Yamaha

representative or the authorized distributor listed below.

Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou

au distributeur le plus proche de vous ﬁgurant dans la liste suivante.

Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten

Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen

Bestimmungsländern erhältlich.

Para detalles sobre productos, contacte su tienda Yamaha más cercana

o el distribuidor autorizado que se lista debajo.

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Scarborough, Ontario,

M1S 3R1, Canada

Tel: 416-298-1311

U.S.A.

Yamaha Corporation of America

6600 Orangethorpe Ave., Buena Park, Calif. 90620,

U.S.A.

Tel: 714-522-9011

MEXICO

Yamaha de México S.A. de C.V.

Calz. Javier Rojo Gómez #1149,

Col. Guadalupe del Moral

C.P. 09300, México, D.F., México

Tel: 55-5804-0600

BRAZIL

Yamaha Musical do Brasil Ltda.

Rua Joaquim Floriano, 913 - 4' andar, Itaim Bibi,

CEP 04534-013 Sao Paulo, SP. BRAZIL

Tel: 011-3704-1377

ARGENTINA

Yamaha Music Latin America, S.A.

Sucursal de Argentina

Olga Cossettini 1553, Piso 4 Norte

Madero Este-C1107CEK

Buenos Aires, Argentina

Tel: 011-4119-7000

PANAMA AND OTHER LATIN

AMERICAN COUNTRIES/

CARIBBEAN COUNTRIES

Yamaha Music Latin America, S.A.

Torre Banco General, Piso 7, Urbanización Marbella,

Calle 47 y Aquilino de la Guardia,

Ciudad de Panamá, Panamá

Tel: +507-269-5311

THE UNITED KINGDOM

Yamaha Music U.K. Ltd.

Sherbourne Drive, Tilbrook, Milton Keynes,

MK7 8BL, England

Tel: 01908-366700

GERMANY

Yamaha Music Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

SWITZERLAND/LIECHTENSTEIN

Yamaha Music Europe GmbH

Branch Switzerland in Zürich

Seefeldstrasse 94, 8008 Zürich, Switzerland

Tel: 01-383 3990

AUSTRIA

Yamaha Music Europe GmbH Branch Austria

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-60203900

CZECH REPUBLIC/SLOVAKIA/

HUNGARY/SLOVENIA

Yamaha Music Europe GmbH Branch Austria

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-602039025

POLAND

Yamaha Music Europe GmbH

Branch Sp.z o.o. Oddzial w Polsce

ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland

Tel: 022-868-07-57

THE NETHERLANDS/

BELGIUM/LUXEMBOURG

Yamaha Music Europe Branch Benelux

Clarissenhof 5-b, 4133 AB Vianen, The Netherlands

Tel: 0347-358 040

FRANCE

Yamaha Musique France

BP 70-77312 Marne-la-Vallée Cedex 2, France

Tel: 01-64-61-4000

ITALY

Yamaha Musica Italia S.P.A.

Combo Division

Viale Italia 88, 20020 Lainate (Milano), Italy

Tel: 02-935-771

SPAIN/PORTUGAL

Yamaha Música Ibérica, S.A.

Ctra. de la Coruna km. 17, 200, 28230

Las Rozas (Madrid), Spain

Tel: 91-639-8888

SWEDEN

Yamaha Scandinavia AB

J. A. Wettergrens Gata 1, Box 30053

S-400 43 Göteborg, Sweden

Tel: 031 89 34 00

DENMARK

YS Copenhagen Liaison Ofﬁce

Generatorvej 6A, DK-2730 Herlev, Denmark

Tel: 44 92 49 00

NORWAY

Norsk ﬁlial av Yamaha Scandinavia AB

Grini Næringspark 1, N-1345 Østerås, Norway

Tel: 67 16 77 70

RUSSIA

Yamaha Music (Russia)

Ofﬁce 4015, entrance 2, 21/5 Kuznetskii

Most street, Moscow, 107996, Russia

Tel: 495 626 0660

OTHER EUROPEAN COUNTRIES

Yamaha Music Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: +49-4101-3030

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2313

TURKEY/CYPRUS

Yamaha Music Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

OTHER COUNTRIES

Yamaha Music Gulf FZE

LOB 16-513, P.O.Box 17328, Jubel Ali,

Dubai, United Arab Emirates

Tel: +971-4-881-5868

THE PEOPLE’S REPUBLIC OF CHINA

Yamaha Music & Electronics (China) Co.,Ltd.

2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,

Shanghai, China

Tel: 021-6247-2211

INDIA

Yamaha Music India Pvt. Ltd.

5F Ambience Corporate Tower Ambience Mall Complex

Ambience Island, NH-8, Gurgaon-122001, Haryana, India

Tel: 0124-466-5551

INDONESIA

PT. Yamaha Music Indonesia (Distributor)

PT. Nusantik

Gedung Yamaha Music Center, Jalan Jend. Gatot

Subroto Kav. 4, Jakarta 12930, Indonesia

Tel: 21-520-2577

KOREA

Yamaha Music Korea Ltd.

8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong,

Kangnam-Gu, Seoul, Korea

Tel: 080-004-0022

MALAYSIA

Yamaha Music Malaysia, Sdn., Bhd.

Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,

Petaling Jaya, Selangor, Malaysia

Tel: 3-78030900

SINGAPORE

Yamaha Music Asia Pte., Ltd.

#03-11 A-Z Building

140 Paya Lebor Road, Singapore 409015

Tel: 747-4374

TAIWAN

Yamaha KHS Music Co., Ltd.

3F, #6, Sec.2, Nan Jing E. Rd. Taipei.

Taiwan 104, R.O.C.

Tel: 02-2511-8688

THAILAND

Siam Music Yamaha Co., Ltd.

4, 6, 15 and 16

ﬂoor, Siam Motors Building,

891/1 Rama 1 Road, Wangmai,

Pathumwan, Bangkok 10330, Thailand

Tel: 02-215-2626

OTHER ASIAN COUNTRIES

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2317

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

Level 1, 99 Queensbridge Street, Southbank,

Victoria 3006, Australia

Tel: 3-9693-5111

COUNTRIES AND TRUST

TERRITORIES IN PACIFIC OCEAN

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2313

NORTH AMERICA

CENTRAL & SOUTH AMERICA

EUROPE

AFRICA

MIDDLE EAST

ASIA

OCEANIA

HEAD OFFICE

Yamaha Corporation, Pro Audio Division

Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650

Tel: +81-53-460-2441

PA25

PM5D/PM5D-RH V2

DSP5D

Yamaha Manual Library

http://www.yamaha.co.jp/manual/

Yamaha Pro Audio global web site:

http://www.yamahaproaudio.com/

U.R.G., Pro Audio Division

006IPTO-H0

Printed in Japan

WN71340

Yamaha PM5D-RH El manual del propietario

Marca: Yamaha

Modelo: PM5D-RH

Categoría: Mezcladores de audio

Tipo: El manual del propietario

Este manual también es adecuado para

PM5D
V2

Descargar PDF

informe

En otros idiomas

français: Yamaha PM5D-RH Le manuel du propriétaire
italiano: Yamaha PM5D-RH Manuale del proprietario
English: Yamaha PM5D-RH Owner's manual
Deutsch: Yamaha PM5D-RH Bedienungsanleitung
русский: Yamaha PM5D-RH Инструкция по применению
Nederlands: Yamaha PM5D-RH de handleiding
português: Yamaha PM5D-RH Manual do proprietário
dansk: Yamaha PM5D-RH Brugervejledning
polski: Yamaha PM5D-RH Instrukcja obsługi
čeština: Yamaha PM5D-RH Návod k obsluze
svenska: Yamaha PM5D-RH Bruksanvisning
Türkçe: Yamaha PM5D-RH El kitabı
suomi: Yamaha PM5D-RH Omistajan opas
română: Yamaha PM5D-RH Manualul proprietarului

Yamaha PM5D-RH El manual del propietario

Este manual también es adecuado para

Yamaha PM5D-RH El manual del propietario

En otros idiomas

Documentos relacionados

Otros documentos