Reese 30944 Guía de instalación

Marca: Reese

Modelo: 30944

Tipo: Guía de instalación

Installation Instructions

M5 HEAD Part Number:

30892

WARNING:Under no circumstances do we recommend exceeding the towing vehicle manufacturers recommended vehicle towing capacity.

#Description Qty. #Description Qty. #Description Qty.

1Assembly –Head Unit 1 2 Handle 1 3 ½” Pull Pin 2

4Spring Clip 25a M8 Carriage Bolt 25b M8 Lock Washer 2

5c M8 Nut 26* Bolts & Washers 4

READ ALL INSTRUCTIONS BEFORE STARTING THE INSTALLATION

1. Assembly………..………………............p 2

2. Maintenance………………….………...p 3

3. Head/Handle Position Overview………p 4

4. Hitching…………….……...……………p 5

5. Pull Test………………..……..............p 5

6. Unhitching………..………………......p 6

7. Warranty………..….……..………….p 7

Table of Contents

*Note: Leg Assembly instructions can be found under their individual part number

VEHICLE FORWARD

Legs Sold Separately

(GM shown)

Equipment Required:

Wrenches: M13

FIG. 1

Fasteners shown with (*) are supplied with leg unit.

FOR INSTALLATION

WITH M5 MOUNTING LEGS

& CENTER SECTION

Center Section Sold

Separately

(20K shown)

Assembly

x 2

FIG. 2 FIG. 3

FIG. 6

FIG. 5

FIG. 4

Installation Instructions

HEAD Part Number:

30892

Handle Assembly

1. Slide tube over the bar as shown in figure 2, and securely tighten with carriage bolts, lock washers and nuts with M13 wrench.

Handle should be snug.

Head Attachment to Center Section

1. Apply grease per page 3, figures 7 & 8. Place head unit on top of center section as shown in figure 4, making sure to avoid putting

any body parts in pinch points

2. Insert pull pin as shown in figure 5, and secure with spring clips. Both sides required.

3. Inspect through sight holes on top of head pan to make sure clips are assembled correctly, as shown in figure 6

Printed in Mexico

Typical Grease needle generally

available at auto parts stores

Installation Instructions

HEAD Part Number:

30892

Grease location

Prior to installing head

Head

1. Preventative lubrication should be applied to the following to keep the head functioning properly;

A. Apply grease to skid plate surface to provide lubricated surface for attachment to trailer.

Note: Plastic lube plates can be used to avoid messy grease. Plate must not exceed 3/16” in thickness to ensure hitch works

properly. REESE 5th Wheel Lube Plate #83001 is recommended.

B. Apply grease to 5th wheel jaw and/or kingpin on the trailer.

C. Apply grease via the grease fitting on the top of the unit. (Grease needle required, see fig. 8) Head comes pre-greased

D. Apply spray on white lithium grease to internal mechanisms -rotate handle a few times to distribute the lubricant.

Note: May need to wipe down unit to remove large debris before application of grease.

Before First Use and Periodic Required Maintenance

FIG. 7

FIG. 8

Ready-to-Receive Position:

When will the head will be in this position?

-When delivered

-When hitch not in use

-When coupling to trailer

-After uncoupling from trailer

How to tell the head is in this position:

-Handle is pulled out fully until audible “CLICK” is heard and holes

DO NOT align for bail pin

-Handle is easily movable towards cab, and returns to

default position upon release

-Indicator shows RED

Locked Position:

When will the head will be in this position?

-When coupled to trailer

How to tell the head is in this position:

-Handle is in a position that holes align

for bail pin insertion.

-Indicator ONLY shows GREEN

Unhitching Position:

When will the head will be in this position?

-When unhitching the trailer

How to tell the head is in this position:

-Handle is in position shown*

-Indicator shows RED

*If there is tension between truck and trailer, the truck or trailer may shift when handle is pulled. In this case, handle will start to return to

ready-to-receive position, but trailer will still uncouple.

Functionality Overview

FIG. 9

FIG. 10

FIG. 11

Installation Instructions

HEAD Part Number:

30892

RED

GREEN

Bail pin holes

DO NOT Align

Bail pin holes

Do Align

Hitching Procedure

Before hitching to a trailer, make sure your 5th wheel height is correct.

Information on how to properly set the height of your 5th wheel hitch can be found in the Leg Installation Instructions.

Failure to follow these instructions may result in death or serious injury

1) Make sure truck and trailer is in position to couple

A. Truck tailgate is lowered if necessary

B. Blocks/Chocks are firmly against each trailer wheel to prevent any possible forward or rearward motion.

C. Pin box is at correct height for hitching (fig. 12 & 13).

D. Make sure head is in Ready-to-Receive position (pg. 4, fig. 9) by pulling the handle out fully

until an audible “CLICK” is heard

2) Back truck slowly into trailer so the trailer king pin and 5th wheel funnel align. When the indicator turns completely green, the

trailer king pin is securely held by the 5th wheel jaw (pg. 4, fig. 10).*

3) Perform Pull Test –

A. With trailer wheels still firmly blocked, trailer landing gears firmly on the ground supporting trailer weight, and trailer

brake on, make sure no one is between the truck and trailer.

B. Try to pull trailer slowly forward. If trailer is properly hitched, proceed to Step 4. If trailer is not properly hitched,

trailer will separate from hitch, and truck will move forward -repeat steps 1 thru 3.

4) Insert bail pin into lock hole, as shown in figure 14.

5) Connect electrical cable and breakaway switch cable between truck and trailer, raise tailgate if necessary.

6) Remove chocks/blocks and lift trailer jacks.

*Jaw may not close if under compression. If fully backed into trailer and not fully latched, pull truck slowly forward to remove load on jaw. Handle

will fully latch.

FIG. 12 FIG. 13

Bottom of Pin Box to be aligned

with top of Skid Plate ramp +/-1

inch

Bail pin shown inserted & locked

FIG. 14

CONTACT ZONE

+/-1in. from top of

skid plate ramp

Installation Instructions

HEAD Part Number:

30892

Indicator shows

Green

Unhitching Procedure

Failure to follow these instructions may result in death or serious injury

1) Make sure trailer is secure

A. Blocks/Chocks are firmly against each trailer wheel to prevent any possible forward or rearward motion.

B. Trailer jacks are lowered and are firmly on the ground

2) Make sure truck is ready to unhitch:

A. Tailgate is lowered if necessary

B. Electrical cable and breakaway switch cable are disconnected.

3) Remove bail pin and move handle to unhitching position (pg. 4, fig. 11) by pulling out fully (fig. 15) until an audible “CLICK” is

heard then rotating handle towards cab (fig. 16).*

4) Drive truck slowly away from trailer

*If there is tension between truck and trailer, the truck or trailer may shift when handle is pulled. In this case, handle will start to return to ready-to-

receive position, but trailer will still uncouple.

FIG. 15 FIG. 16

Installation Instructions

HEAD Part Number:

30892

Trailer pin box VEHICLE FORWARD

If handle will not move to the unhitching position (pg. 4, fig. 11) with ease, STOP, DO NOT FORCE

THE HANDLE!!! The jaw may not open if under tension. Slowly reverse truck to remove load on

the jaw before attempting to unhitch trailer.

Installation Instructions

Head

NOTES:

Horizon Global

47912 Halyard Drive Suite 100

Plymouth, MI 48170

LIMITED LIFETIME WARRANTY

1. Limited Lifetime Warranty (“Warranty”). Horizon Global (“We” or “Us”) warrants to the original consumer purchaser only

(“You”) that the product will be free from material defects in both material and workmanship for a period of lifetime of

ownership, ordinary wear and tear excepted; provided that installation and use of the product is in accordance with product

instructions. There are no other warranties, express or implied, including the warranty of merchantability or fitness for a

particular purpose. This warranty is not transferable.

2. Limitations on the Warranty. This Warranty does not cover: (a) normal wear and tear; (b) damage through abuse, neglect,

misuse, or as a result of any accident or in any other manner; (c) damage from misapplication, overloading, or improper

installation; (d) improper maintenance and repair; and (e) product alteration in any manner by anyone other than Us, with the

sole exception of alterations made pursuant to product instructions and in a workmanlike manner.

3. Obligations of Purchaser. To make a Warranty claim, contact Us at 47912 Halyard Drive Suite 100, Plymouth, MI, 48170,

1-800-632-3290, identify the product by model number, and follow the claim instructions that will be provided. Any returned

product that is replaced by Us becomes our property. You will be responsible for return shipping costs. Please retain your

purchase receipt to verify date of purchase and that You are the original consumer purchaser. The product and the purchase

receipt must be provided to Us in order to process Your warranty claim.

4. Remedy Limits. Product replacement is Your sole remedy under this Warranty. We shall not be liable for service or labor

charges incurred in removing or replacing a product or any incidental or consequential damages of any kind.

5. Assumption of Risk. You acknowledge and agree that any use of the product for any purpose other than the specified use(s)

stated in the product instructions is at Your own risk.

6. Governing Law. This Warranty gives You specific legal rights, and You also may have other rights which vary from state

to state. This Warranty is governed by the laws of the State of Michigan, without regard to rules pertaining to conflicts of

law. The state courts located in Oakland County, Michigan shall have exclusive jurisdiction for any disputes relating to this

Warranty.

Part Number Purchased:

Place of Purchase:

Date of Purchase:

Part Manufactured Date (located on driver-side sticker):

fInstallation Instructions

M5 HEAD & CENTER SECTION

Hitch Rated for 32,000 lbs,

Max. Pin Weight 6,400 lbs

Part Number:

30892 & 30932

# Description Qty. # Description Qty. # Description Qty.

1 Assembly –Head Unit 1 2 Handle 1 3 ½” Pull Pin 2

4 Spring Clip 2 5a M8 Carriage Bolt 2 5b M8 Lock Washer 2

5c M8 Nut 2 6 Center Section (30932) 1 7* Bolts, Nuts & Washers 4

READ ALL INSTRUCTIONS BEFORE STARTING THE INSTALLATION

Assembly………..………………..........p 2

Maintenance………………….………..p 3

Head/Handle Position Overview……p 4

Hitching…………….……...……………p 5

Pull Test………………..……..............p 5

Unhitching………..………………......p 6

Added Clearance to Cab…....………p 7

Warranty………..….……..….……….p 8

Table of Contents

*Note: Leg Assembly instructions can be found under their individual part number

VEHICLE FORWARD

Legs Sold Separately

(Ford shown)

Equipment Required:

•Fastener kit 30892F

•M13, M24 socket and wrench

•Torque Wrench

•Lithium Grease

FIG. 1

Fasteners shown with (*) are supplied with leg unit.

FOR INSTALLATION

WITH M5 MOUNTING LEGS

WARNING: Under no circumstances do we recommend exceeding the towing vehicle manufacturers recommended vehicle towing capacity.

Failure to follow instructions for installation and use may cause property damage, injury or death.

Handle Assembly

1. Slide tube over the bar as shown in figure 2, and securely tighten with carriage bolts, lock washers and nuts with M13

wrench. Handle should be snug.

Center Section Attachment to Legs

1. Fasteners and assembly instructions are included with the set of legs, sold separately.

2. For height adjustment, the unit should be set to have a minimum of 6” clearance between the truck bed rail and the

bottom of the trailer. This unit has 3 possible attachment locations, with 4” of overall adjustment.

3. For added clearance to the truck cab, see page 7.

Head Attachment to Center Section

1. Apply grease per page 3, figure 9. Place head unit on top of center section, making sure to avoid putting any body parts

in pinch points

2. Insert pull pin as shown in figure 6, and secure with spring clips. Both sides required.

3. Inspect through sight holes on top of head pan to make sure clips are assembled correctly, as shown in figure 7

Assembly

x 2

FIG. 2 FIG. 3

FIG. 7FIG. 6FIG. 5

Installation Instructions

HEAD & CENTER SECTION Part Number:

30892 & 30932

4” of Adjustment

FIG. 4

Pinch areas

Sight Holes

Printed in Mexico

Typical Grease needle generally

available at auto parts stores

Installation Instructions

HEAD & CENTER SECTION Part Number:

30892 & 30932

Grease location

Prior to installing head

Hole provided for 5/16”

eye bolt to attach trailer

break-away cable to.

Pivot Grease fitting.

Accessible thru logo/load

rating slot. Use of grease

needle required.

Maintenance

FIG. 9A

FIG. 9B

Pivot bolt and nut

Access for

open end

wrench

This unit is designed to need very little maintenance and be one of the quietest on the market.

In order to ensure long term performance, it is recommended to lubricate as indicated below;

Every Use

1. Apply grease to skid plate surface, to provide lubricated surface for attachment to trailer.

Note: Plastic lube plates can be used to avoid messy grease. Plate must not exceed 3/16” in thickness to ensure hitch works

properly. REESE 5th Wheel Lube Plate #83001 is recommended.

2. Apply grease to 5th wheel jaw and/or kingpin on the trailer.

Jaw

Skid Plate

FIG. 8

Annually/As Required

1. Apply grease via the grease fitting on the top of the unit. (Grease needle required, see fig. 9) Head comes pre-greased

2. Apply spray on white lithium grease to internal mechanisms - rotate handle a few times to distribute the lubricant.

Note: May need to wipe down unit to remove large debris before application of grease.

3. Greasing the pivot assemblies can easily be done with a grease gun that has a needle adapter installed.

4. The pivot assembly resistance is preset at factory. If head pivots and makes noise when trailer is not attached, adjust

the resistance more by tighten pivot bolt 1/2 turn at a time (2 full turns max.). See figure 9B.

5. The pivot assembly can be rebuilt if require. Instructions to do this will be in rebuild kit.

Head Grease fitting

Internal Mechanisms

Ready-to-Receive Position:

When will the head will be in this position?

- When delivered

- When hitch not in use

- When coupling to trailer

- After uncoupling from trailer

How to tell the head is in this position:

- Handle is pulled out so holes do not align for bail pin

- Handle is easily movable towards cab, and returns to

default position upon release

- Indicator shows RED

Locked Position:

When will the head will be in this position?

- When coupled to trailer

How to tell the head is in this position:

- Handle is in a position that holes align

for bail pin insertion.

- Indicator ONLY shows GREEN

Unhitching Position:

When will the head will be in this position?

- When unhitching the trailer

How to tell the head is in this position:

- Handle is in position shown*

- Indicator shows RED

*If there is tension between truck and trailer, the truck or trailer may shift when handle is pulled. In this case, handle will start to return to

ready-to-receive position, but trailer will still uncouple.

Functionality Overview

FIG. 10

FIG. 11

FIG. 12

Installation Instructions

HEAD & CENTER SECTION Part Number:

30892 & 30932

RED

GREEN

Bail pin hole

Hitching Procedure

Before hitching to a trailer, make sure your 5th wheel height is correct.

Information on how to properly set the height of your 5th wheel hitch can be found in the Leg Installation

Instructions.

Failure to follow these instructions may result in death or serious injury

1) Make sure truck and trailer is in position to couple

A. 5th wheel is correctly secured to truck

B. Truck tailgate is lowered if necessary

C. Blocks/Chocks are firmly against each trailer wheel to prevent any possible forward or rearward motion.

D. Pin box is at correct height for hitching (fig. 13 & 14).

E. Make sure head is in Ready-to-Receive position (pg. 4, fig.10)

2) Back truck slowly into trailer so the trailer king pin and 5th wheel funnel align. Hitch will latch automatically when truck is

backed completely into trailer king pin. When this occurs, the indicator will be 100% green (pg. 4, fig. 11).*

3) Perform Pull Test –

A. With trailer wheels still firmly blocked, trailer landing gears firmly on the ground supporting trailer weight, and

trailer brake on, make sure no one is between the truck and trailer.

B. Try to pull trailer slowly forward. If trailer is properly hitched, proceed to Step 4. If trailer is not properly

hitched, trailer will separate from hitch, and truck will move forward - repeat steps 1 thru 3.

4) Insert bail pin into lock hole, as shown in figure 15, or lock for added security. Possible lock dimensions shown on

page 6.

5) Connect electrical cable and breakaway switch cable between truck and trailer, raise tailgate if necessary.

6) Remove chocks/blocks and lift trailer jacks.

*Jaw may not close if under compression. If fully backed into trailer and not fully latched, pull truck slowly forward to remove load on jaw.

Handle will fully latch.

FIG. 13 FIG. 14

Bottom of Pin Box to be aligned

with top of Skid Plate ramp +/-

1 inch

Bail pin shown inserted & locked

FIG. 15

CONTACT ZONE

+/- 1in. from top of

skid plate ramp

Installation Instructions

HEAD & CENTER SECTION Part Number:

30892 & 30932

Indicator shows

Green

Unhitching Procedure

Failure to follow these instructions may result in death or serious injury

1) Make sure trailer is secure

A. Blocks/Chocks are firmly against each trailer wheel to prevent any possible forward or rearward motion.

B. Trailer jacks are lowered and are firmly on the ground

2) Make sure truck is ready to unhitch:

A. Tailgate is lowered as necessary

B. Electrical cable and breakaway switch cable are disconnected.

3) As truck and trailer may shift when unhitching, ensure no person or vehicle is in the vicinity of truck or trailer when

unhitching

4) Remove bail pin from locking hole, and move handle to unhitching position (fig. 17) by pulling out and rotating towards

handle towards cab.*

5) Drive truck slowly away from trailer

*If there is tension between truck and trailer, the truck or trailer may shift when handle is pulled. In this case, handle will start to return to

ready-to-receive position, but trailer will still uncouple.

FIG. 16 FIG. 17

Installation Instructions

HEAD & CENTER SECTION Part Number:

30892 & 30932

Trailer pin box

1-1/2”

or greater

3/4” or greater

Ø 5/16” or less

Printed in Mexico

TO INCREASE THE GAP BETWEEN TRAILER AND TRUCK CAB by 1-1/2”.

Logo/Rating cover

Plastic retainers

Grease points

Head springs

View holes to

help spring clip

installation

Installation Instructions

HEAD & CENTER SECTION Part Number:

30892 & 30932

FIG. 18

Head spring

assembly

Pinch

points

Pinch

points

Shown in factory location with offset towards cab of truck

The center section has an option to increase the gap between the trailer front and the truck cab by 1-1/2” by rotating the center section

180 degrees.

Location of king pin should be ahead of truck rear axle and have proper truck cab clearance

1. Remove the head by pulling the spring clips off the head retainer pins. Then pull the head retainer pin out of the head.

Hint; A slight push down on the head will help this. Caution, avoid getting fingers pinched.

2. Lift the head off and set aside.

3. Remove the bolts holding the legs on the center section and rotate the center section (all vehicles), OR disconnect the feet from

the bed and rotate the center section and leg assembly (not possible with RAM vehicles).

4. Re connect the center section or the center section and leg assembly per the installation instructions of that portion.

5. Remove the logo/rating cover by gently prying the two lower plastic retainers with the cover away from the center section. Avoid

scratching the paint by using plastic auto trim tools. The top will pivot and pull away once the cover rotates up enough.

6. Re-install on the other side (truck rear) by reversing the above process.

7. Remove the head springs by removing the 1/4” bolt (7/16” socket) and flip them from right to left. When installed properly, the

springs should be pointing up towards the truck cab and tighten to 7-8 ft-lbs. Springs will flex freely.

8. Re apply grease to the head and center section interface and re-install the head per instructions.

Caution; place hands or fingers on either side of the pivot interface to prevent pinching.

9. Re-install head retainer pins and clips per head instructions.

*30894 27k Center section shown

Product Instructions:

Head & Center Section

NOTES:

Horizon Global America, Inc

47912 Halyard Drive Suite 100

Plymouth, MI 48170

LIMITED LIFETIME WARRANTY

1. Limited Lifetime Warranty (“Warranty”). Horizon Global (“We” or “Us”) warrants to the original consumer purchaser

only (“You”) that the product will be free from material defects in both material and workmanship for a period of

lifetime of ownership, ordinary wear and tear excepted; provided that installation and use of the product is in

accordance with product instructions. There are no other warranties, express or implied, including the warranty of

merchantability or fitness for a

particular purpose. This warranty is not transferable.

2. Limitations on the Warranty. This Warranty does not cover: (a) normal wear and tear; (b) damage through abuse,

neglect, misuse, or as a result of any accident or in any other manner; (c) damage from misapplication, overloading,

or improper installation; (d) improper maintenance and repair; and (e) product alteration in any manner by anyone

other than Us, with the sole exception of alterations made pursuant to product instructions and in a workmanlike

manner.

3. Obligations of Purchaser. To make a Warranty claim, contact Us at 47912 Halyard Drive Suite 100, Plymouth, MI,

48170, 1-800-632-3290, identify the product by model number, and follow the claim instructions that will be provided.

Any returned product that is replaced by Us becomes our property. You will be responsible for return shipping costs.

Please retain your purchase receipt to verify date of purchase and that You are the original consumer purchaser.

The product and the purchase receipt must be provided to Us in order to process Your warranty claim.

4. Remedy Limits. Product replacement is Your sole remedy under this Warranty. We shall not be liable for service

or labor charges incurred in removing or replacing a product or any incidental or consequential damages of any kind.

5. Assumption of Risk. You acknowledge and agree that any use of the product for any purpose other than the

specified use(s) stated in the product instructions is at Your own risk.

6. Governing Law. This Warranty gives You specific legal rights, and You also may have other rights which vary from

state to state. This Warranty is governed by the laws of the State of Michigan, without regard to rules pertaining to

conflicts of law. The state courts located in Oakland County, Michigan shall have exclusive jurisdiction for any

disputes relating to this Warranty.

Part Number Purchased:

Place of Purchase:

Date of Purchase:

Part Manufactured Date (located on driver-side sticker):

Product Instructions

M5 GM LEG

Part Number:

30942

FOR INSTALLATION WITH M5

HEAD AND CENTER SECTION

Page 1 of 18

1. Installation ---------------------------- p 1

2. Assembly and Installation ------- p 2 - 4 3. Maintenance ------------------------------- p 6

4. Warranty ------------------------------------ p 7

CAUTION: Under no circumstances do we recommend exceeding the towing vehicle

manufacturers recommended vehicle towing capacity.

READ ALL INSTRUCTIONS BEFORE STARTING THE INSTALLATION OR USE

Table of Contents

VEHICLE FORWARD

M5 5th Wheel Head

(Sold Separately)

FIG. 1

M5 32K Center

Section (Sold

Separately)

910

WARNING: FAILURE TO FOLLOW INSTALLATION AND HITCH-UP INSTRUCTIONS MAY

CAUSE PROPERTY LOSS, SERIOUS INJURY, OR DEATH!

Equipment Required:

Wrenches: 15/16”

Pliers

Torque wrench

# Description QTY.

1 M5 GM Leg

(30942) 1

2 Bolt-5/8-11 x

4.25” GR8 4

3 Washer – 5/8”

Conical 4

4 Nut –5/8-11 4

5 Handle, T-Pin

Locking 4

6 Lynch Pin,

Handle Lock 2

7 Castle Nut, M5

GM 4

8 Cotter Pin, M5

GM Leg 8

9 T-Pin, GM M5 4

10 T-Bushing, GM

M5 4

Product Instructions

M5 GM LEG

Part Number:

30942

FOR INSTALLATION WITH M5

HEAD AND CENTER SECTION

Page 2 of 18

1. The M5 GM Leg comes pre-assembled, adjusted, and ready to install.

2. Determine which center section mounting holes to use to ensure a minimum of 6” clearance between the truck bed rail and

the bottom of the trailer. ( For more detail, please refer to the GUIDELINES FOR MATCHING HITCH, TRUCK, AND

TRAILER section located in the head and center section instruction sheet.) Legs should be attached at same height on

both sides of unit. This unit has 4” of vertical adjustment.

3. Using the (4) 5/8” Hex Head Bolts and conical washers (teeth side toward hitch), attach the legs to the center section

structure, inserting the bolts from the outside of the center section through the bolt hole in the legs and into the inside of the

center section. Thread on the 5/8” nuts and conical washers (teeth side toward hitch), finger tighten fasteners initially until

final adjustments are made.

ASSEMBLY AND INSTALLATION

Product Instructions

M5 GM LEG

Part Number:

30942

FOR INSTALLATION WITH M5

HEAD AND CENTER SECTION

Page 3 of 18

5. Remove the (2) lynch pins and position legs over pucks with handles in OPEN position as shown.

6. Once unit has been placed in pucks, rotate handles back to CLOSED position and insert the lynch pins back into the leg to

prevent handles from opening during operation. Lynch Pin

(Shown Open)

Lynch Pin

(Shown Closed)

Handles

(Shown Open)

Product Instructions

M5 GM LEG

Part Number:

30942

FOR INSTALLATION WITH M5

HEAD AND CENTER SECTION

Page 4 of 18

7. Due to variations in truck underbeds, it is normal for some handles to be loose and other handles to be too tight to lock. If a

handle appears to loose and rattles or cannot be closed fully, remove the cotter pin and adjust castle nut by hand to a

position where handle does not rattle or is able to close.

8. Once handle adjustment is satisfactory, re-insert cotter pin and bend end with pliers to hold in place. Additional cotter pins

are provided in the hardware kit for your convenience.

9. With GM Leg T-Pin handles locked and T-Pins securely held in underbed structure, tighten each 5/8” hex-head bolt to

210 ft-lb of torque.

10. Verify that hitch is tight to truck bed by lifting each side of the hitch.

11. Assemble head to center section per instructions included with M5 Center Section and Head.

Finger tighten castle nut only!

Lynch pin

(shown Closed)

Product Instructions

M5 GM LEG

Part Number:

30942

FOR INSTALLATION WITH M5

HEAD AND CENTER SECTION

Page 5 of 18

In order to maintain performance over the life of the product:

1. Before any trip, verify that cotter pins, foot bracket and castle nut are undamaged and securely locked. Additionally ensure

that the lynch pins are also securely locked in place, with little to no vertical play. The image below shows the proper

orientation of the lynch pin in relation to the foot.

2. Every 1,000 miles, check the 5/8” hex bolts that connect center section to legs to insure that they are still torqued to 210 ft-

lb of torque.

3. For general maintenance of the entire 5th wheel hitch assembly, please refer to the M5 head and center section instruction

sheet.

MAINTENANCE

Product Instructions

M5 GM LEG

Part Number:

30942

FOR INSTALLATION WITH M5

HEAD AND CENTER SECTION

Page 6 of 18

LIMITED LIFETIME WARRANTY

Horizon Global Corporation. (“We” or “Us”) warrants to the original consumer purchaser only (“You”) that the product

will be free from material defects in both material and workmanship, ordinary wear and tear expected; provided that

installation and use of the product is in accordance with product instructions. There are no other warranties, express

or implied, including the warranty of merchantability or fitness for a particular purpose. This warranty is not

transferable.

This warranty does not cover: (a) normal wear and tear; (b) damage through abuse, neglect, misuse, or as a result of

any accident or in any other manner; (c) damage from misapplication, overloading, or improper installation; (d)

improper maintenance and repair; and (e) product alteration in any manner by anyone other than Us, with the sole

exception of alterations made pursuant to product instructions and in a workmanlike manner.

To make a Warranty claim, contact Us, at our principal address of 47912 Halyard Dr. Suite 100, Plymouth, MI 48170,

1-800-632-3290, identify the product by model number, and follow the claim instructions that will be provided. Any

returned product that is replaced by Us becomes our property. You will be responsible for return shipping costs.

Please retain your purchase receipt to verify date of purchase and that You are the original consumer purchaser. The

product and the purchase receipt must be provided to Us in order to process Your Warranty claim.

Product replacement is Your sole remedy under this Warranty. We shall not be liable for service or labor charges

incurred in removing or replacing a product or any incidental or consequential damages of any kind.

You acknowledge and agree that any use of the product for any purpose other than the specified use(s) stated in the

product instructions is at Your own risk.

This Warranty gives you specific legal rights, and You may also have other rights which vary from state to state. This

Warranty is governed by the laws of the State of Michigan, without regard to rules pertaining to conflicts of law. The

state courts located in Oakland county, Michigan shall have exclusive jurisdiction for any disputes relating to this

warranty.

Horizon Global

47912 Halyard Dr. Suite 100

Plymouth, MI 48170

For the most up to date product

instructions, installation and use

information please scan the QR

code or call

Product Instructions

M5 GM LEG

Part Number:

30942

FOR INSTALLATION WITH M5

HEAD AND CENTER SECTION

Page 7 of 18

1. Installation ---------------------------- p 1

2. Assemblée et Installation ------- p 2 - 4 3. entretien ------------------------------- p 6

4. garantie ------------------------------------ p 7

prudence: En aucun cas, nous ne recommandons de dépasser la capacité de remorquage

recommandée par les constructeurs de véhicules.

LIRE TOUTES LES INSTRUCTIONS AVANT DE COMMENCER L’INSTALLATION

OU L’UTILISATION

Tableau des matières

VÉHICULE VERS L’AVANT

M5 5ème Tête de roue

(Vendu séparément)

FIG. 1

Section

centrale M5 32K

(Vendu

séparément)

910

WARNING: LE NON-RESPECT DES INSTRUCTIONS D’INSTALLATION ET D’ATTELAGE

PEUT CAUSER UNE PERTE DE BIENS, DES BLESSURES GRAVES OU LA MORT!

Équipement requis:

Clés: 15/16”

pinces

clé dynamométrique

# description QTY.

1 Jambe GM M5

(30942) 1

2boulon-5/8-11 x

4.25” GR8 4

3 laveuse – 5/8”

Conical 4

4 écrou –5/8-11 4

5 manche, T-Pin

verrouillage 4

6 Épinglette

Lynch,

Verrouillage de

poignée

7 Écrou de

château, M5 GM 4

8 goupille

, M5 GM

Leg 8

9 T-épingler, GM

M5 4

10 T-Bague, GM

M5 4

Product Instructions

M5 GM LEG

Part Number:

30942

FOR INSTALLATION WITH M5

HEAD AND CENTER SECTION

Page 8 of 18

1. The M5 GM Leg vient pré-assemblé, ajusté et prêt à installer.

2. Déterminez les trous de montage de la section centrale à utiliser pour assurer un dégagement d’au moins 6 pieds entre le

rail de lit du camion et le fond de la remorque. ( Pour plus de détails, veuillez consulter la section LIGNES DIRECTRICES

POUR L’ATTELAGE CORRESPONDANT, LE CAMION ET LA REMORQUE situé dans la fiche d’instructions de la section

principale et centrale.) Les jambes doivent être fixées à la même hauteur des deux côtés de l’unité. Cette unité a 4 »

d’ajustement vertical.

3. À l’aide des boulons hex (4) 5/8 » et des rondelles coniques (côté dents vers l’attelage), fixez les jambes à la structure de la

section centrale, en insérant les boulons de l’extérieur de la section centrale par le trou de boulon dans les jambes et à

l’intérieur de la section centrale. Enfiler sur les écrous et les rondelles coniques de 5/8 » (côté dents vers l’attelage), serrer

les attaches au début jusqu’à ce que les ajustements finaux soient effectués.

ASSEMBLAGE ET INSTALLATION

Product Instructions

M5 GM LEG

Part Number:

30942

FOR INSTALLATION WITH M5

HEAD AND CENTER SECTION

Page 9 of 18

5. Retirez les (2) goupilles de lynchage et placez les jambes au-dessus des rondelles avec des poignées en position OPEN

comme indiqué.

5. Une fois que l’appareil a été placé dans des rondelles, faites pivoter les poignées vers la position FERMÉE et insérez les

broches de lynchage dans la jambe pour empêcher les poignées de s’ouvrir pendant le fonctionnement.

Épinglette Lynch

(Montré ouvert)

Épinglette Lynch

(Montré fermé)

Poignées

(Montré ouvert)

Product Instructions

M5 GM LEG

Part Number:

30942

FOR INSTALLATION WITH M5

HEAD AND CENTER SECTION

Page 10 of 18

7. En raison des variations des sous-lits des camions, il est normal que certaines poignées soient lâches et que d’autres

poignées soient trop serrées pour être verrouillées. Si une poignée semble se détacher et hochets ou ne peut pas être

fermé complètement, retirez la goupille cotter et ajustez l’écrou du château à la main à une position où la poignée ne

tremble pas ou est capable de fermer.

8. Une fois que l’ajustement de poignée est satisfaisant, réinsérez la goupille de cotter et pliez l’extrémité avec des pinces

pour tenir en place. Des broches cotter supplémentaires sont fournies dans le kit matériel pour votre commodité.

9. Avec des poignées GM Leg T-Pin verrouillées et des T-Pins solidement maintenus dans la structure sous-lit, serrez chaque

boulon de 5/8 » hex-tête à 210 pi-lb de couple.

10. Vérifiez que l’attelage est serré au lit du camion en soulevant chaque côté de l’attelage.

11. Assemblez la section tête à centre par instructions incluses avec la section centrale M5 et la tête.

Doigt serrer écrou château seulement!

Goupille de Lynch

(montré Fermé)

Product Instructions

M5 GM LEG

Part Number:

30942

FOR INSTALLATION WITH M5

HEAD AND CENTER SECTION

Page 11 of 18

Afin de maintenir les performances tout au long de la durée de vie du produit:

1. Avant tout voyage, vérifiez que les broches cotter, support de pied et écrou de château sont intacts et verrouillés en toute

sécurité. En outre, assurez-vous que les broches de lynchage sont également solidement verrouillées en place, avec peu

ou pas de jeu vertical. L’image ci-dessous montre l’orientation correcte de la goupille lynchée par rapport au pied.

2. Tous les 1000 miles, vérifiez les boulons hex 5/8 " qui relient la section centrale aux jambes pour s’assurer qu’ils sont

encore coupled à 210 pi-lb de couple.

3. Pour l’entretien général de l’ensemble de l’attelage de la 5e roue, veuillez consulter la feuille d’instructions de la tête et de

la section centrale M5.

entretien

Product Instructions

M5 GM LEG

Part Number:

30942

FOR INSTALLATION WITH M5

HEAD AND CENTER SECTION

Page 12 of 18

GARANTIE À VIE LIMITÉE

Horizon Global Corporation. (« Nous » ou « Nous ») justifie à l’acheteur consommateur d’origine seulement

(« Vous ») que le produit sera exempt de défauts matériels à la fois dans le matériel et l’exécution, l’usure ordinaire

prévue; à condition que l’installation et l’utilisation du produit soit conforme aux instructions du produit. Il n’y a pas

d’autres garanties, expresses ou implicites, y compris la garantie de marchandité ou d’aptitude à une fin particulière.

Cette garantie n’est pas transférable.

Cette garantie ne couvre pas : a) l’usure normale; b) les dommages causés par la violence, la négligence, l’abus ou à

la suite d’un accident ou d’une autre manière; c) dommages causés par une mauvaise application, une surcharge ou

une installation inappropriée; d) entretien et réparation inadéquats; e) la modification du produit de quelque manière

que ce soit par quelqu’un d’autre que nous, à l’exception des modifications apportées conformément aux instructions

du produit et d’une manière professionnelle.

Pour faire une demande de garantie, communiquez avec nous, à notre adresse principale du 47912 Halyard Dr. Suite

100, Plymouth, MI 48170, 1-800-632-3290, identifiez le produit par numéro de modèle et suivez les instructions de

réclamation qui seront fournies. Tout produit retourné qui est remplacé par Nous devient notre propriété. Vous serez

responsable des frais d’expédition de retour. Veuillez conserver votre reçu d’achat pour vérifier la date d’achat et que

vous êtes l’acheteur consommateur d’origine. Le produit et le reçu d’achat doivent nous être fournis afin de traiter

votre demande de garantie.

Le remplacement du produit est votre seul recours en vertu de cette garantie. Nous ne serons pas responsables des

frais de service ou de main-d’œuvre engagés dans la suppression ou le remplacement d’un produit ou de tout

dommage accessoire ou conséquent de quelque nature que ce soit.

Vous reconnaissez et acceptez que toute utilisation du produit à d’autres fins que l’utilisation spécifiée(s) indiquée

dans les instructions du produit est à vos risques et périls.

Cette garantie vous donne des droits juridiques spécifiques, et vous pouvez également avoir d’autres droits qui

varient d’un État à l’autre. Cette garantie est régie par les lois de l’État du Michigan, sans égard aux règles relatives

aux conflits de droit. Les tribunaux d’État situés dans le comté d’Oakland, michigan doivent avoir compétence

exclusive pour tous les litiges relatifs à cette garantie.

Horizon Global

47912 Halyard Dr. Suite 100

Plymouth, MI 48170

Pour les instructions de produit

les plus à jour, l’installation et

l’utilisation des informations s’il

vous plaît numériser le code QR

ou appeler

Product Instructions

M5 GM LEG

Part Number:

30942

FOR INSTALLATION WITH M5

HEAD AND CENTER SECTION

Page 13 of 18

1. instalación ---------------------------- p 1

2. Montaje e instalación ------- p 2 - 4 3. mantenimiento -------------------------- p 6

4. garantía ------------------------------------ p 7

PRECAUCIÓN: Bajo ninguna circunstancia recomendamos exceder la capacidad

recomendada de remolque de los fabricantes de vehículos de remolque.

LEA TODAS LAS INSTRUCCIONES ANTES DE INICIAR LA INSTALACIÓN O

Tabla de contenidos

VEHÍCULO HACIA ADELANTE

M5 5th Wheel Head

(Se vende por separado)

FIG. 1

M5 32K Center

Section (Se

vende por

separado)

910

ADVERTENCIA: ¡NO SEGUIR LAS INSTRUCCIONES DE INSTALACIÓN Y ENGANCHE

PUEDE CAUSAR PÉRDIDA DE PROPIEDAD, LESIONES GRAVES O LA MUERTE!

Equipment Required:

Llaves: 15/16"

alicates

Llave de torsión

# Description QTY.

1 M5 GM Leg

(30942) 1

2 cerrojo-5/8-11 x

4.25” GR8 4

3 Arandela –5/8"

Cónico 4

4 Nuez –5/8-11 4

5 asa, T-Pin

bloqueo 4

6 Lynch Pin,

Bloqueo del

mango

7 Nuez de castillo,

M5 GM 4

8 pasador

, M5 GM

Leg 8

9 T-Pin, GM M5 4

10 T-Bushing, GM

M5 4

Product Instructions

M5 GM LEG

Part Number:

30942

FOR INSTALLATION WITH M5

HEAD AND CENTER SECTION

Page 14 of 18

1. La pierna M5 GM viene premontada, ajustada y lista para instalarse.

2. Determine qué orificios de montaje de la sección central utilizar para garantizar un mínimo de 6" de distancia entre el riel

de la cama del camión y la parte inferior del remolque. ( Para obtener más detalles, consulte la sección DIRECTRICES

PARA LA COINCIDENCIA DE ENGANCHES, CAMIONES Y REMOLQUEs ubicada en la hoja de instrucciones de la

sección principal y central.) Las patas deben estar unidas a la misma altura en ambos lados de la unidad. Esta unidad

tiene 4" de ajuste vertical.

3. Usando los (4) 5/8" Pernos de cabeza hexagonal y arandelas cónicas (lado de los dientes hacia el enganche), acoplar las

piernas a la estructura de la sección central, insertando los pernos desde el exterior de la sección central a través del

agujero del perno en las piernas y en el interior de la sección central. Rosca en las tuercas de 5/8" y arandelas cónicas

(lado de los dientes hacia el enganche), aprieta los cierres de los dedos inicialmente hasta que se realicen los ajustes

finales.

MONTAJE E INSTALACIÓN

Product Instructions

M5 GM LEG

Part Number:

30942

FOR INSTALLATION WITH M5

HEAD AND CENTER SECTION

Page 15 of 18

5. Retire los (2) pasadores de linchamiento y coloque las piernas sobre los discos con asas en posición OPEN como se

muestra.

6. Una vez que la unidad se ha colocado en discos, gire las asas de nuevo a la posición CERRADA e inserte los pasadores de

linchamiento de nuevo en la pierna para evitar que las asas se abran durante el funcionamiento.

Lynch Pin

(Se muestra

abierto)

Lynch Pin

(Se muestra cerrado)

Manijas

(Se muestra abierto)

Product Instructions

M5 GM LEG

Part Number:

30942

FOR INSTALLATION WITH M5

HEAD AND CENTER SECTION

Page 16 of 18

7. Debido a las variaciones en las camas inferiores de los camiones, es normal que algunas asas estén sueltas y otras

manijas estén demasiado apretadas para bloquearse. Si una manija parece soltarse y sacudirse o no se puede cerrar

completamente, retire el pasador de bobina y ajuste la tuerca del castillo a mano a una posición donde la manija no sacuda

o sea capaz de cerrar.

8. Una vez que el ajuste de la manija sea satisfactorio, vuelva a insertar el pasador de bobina y doble el extremo con alicates

para mantener en su lugar. Se proporcionan pines de bobina adicionales en el kit de hardware para su comodidad.

9. Con las asas gm leg T-Pin bloqueadas y los pasadores T firmemente mantenidos en la estructura de la cama inferior,

apriete cada perno de cabeza hexagonal de 5/8" a 210 pies-lb de torque.

10. Verifique que el enganche esté apretado a la cama del camión levantando cada lado del enganche.

11. Montar sección de cabeza a centro por instrucciones incluidas con M5 Center Section y Head.

Apretó los dedos solo la tuerca del castillo!

Lynch pin

(se muestra cerrado)

Product Instructions

M5 GM LEG

Part Number:

30942

FOR INSTALLATION WITH M5

HEAD AND CENTER SECTION

Page 17 of 18

Con el fin de mantener el rendimiento a lo largo de la vida útil del producto:

1. Antes de cualquier viaje, verifique que los pasadores de bobina, el soporte de pie y la tuerca del castillo no estén dañados

y estén bloqueados de forma segura. Además, asegúrese de que los pasadores de linchamiento también están

bloqueados de forma segura en su lugar, con poco o ningún juego vertical. La siguiente imagen muestra la orientación

adecuada del pasador de linchamiento en relación con el pie.

2. Cada 1.000 millas, compruebe los pernos hexagonal de 5/8" que conectan la sección central con las piernas para asegurar

que todavía están parados a 210 pies-lb de torque.

3. Para el mantenimiento general de todo el conjunto del enganche de la 5ª rueda, consulte la hoja de instrucciones de la

cabeza y la sección central M5.

mantenimiento

Product Instructions

M5 GM LEG

Part Number:

30942

FOR INSTALLATION WITH M5

HEAD AND CENTER SECTION

Page 18 of 18

GARANTÍA LIMITADA DE POR VIDA

Horizon Global Corporation. ("Nosotros" o "Nosotros") garantiza al comprador original del consumidor solamente

("Usted") que el producto estará libre de defectos materiales tanto en el material como en la mano de obra, se espera

un desgaste ordinario; siempre que la instalación y el uso del producto se de acuerdo con las instrucciones del

producto. No hay otras garantías, expresas o implícitas, incluyendo la garantía de comerciabilidad o idoneidad para

un propósito particular. Esta garantía no es transferible.

Esta garantía no cubre: (a) desgaste normal; (b) daños por abuso, negligencia, mal uso o como resultado de

cualquier accidente o de cualquier otra manera; (c) daño por aplicación incorrecta, sobrecarga o instalación

incorrecta; (d) mantenimiento y reparación inadecuados; y (e) alteración del producto de cualquier manera por

cualquier otra persona que no sea Nosotros, con la única excepción de las alteraciones realizadas de conformidad

con las instrucciones del producto y de una manera similar a la del trabajador.

Para realizar una reclamación de garantía, comuníquese con nosotros, en nuestra dirección principal del 47912

Halyard Dr. Suite 100, Plymouth, MI 48170, 1-800-632-3290, identifique el producto por número de modelo y siga las

instrucciones de reclamación que se proporcionarán. Cualquier producto devuelto que sea reemplazado por

Nosotros se convierte en nuestra propiedad. Usted será responsable de los gastos de envío de devolución. Conserve

su recibo de compra para verificar la fecha de compra y que usted es el comprador de consumo original. El producto

y el recibo de compra deben proporcionarse a nosotros para procesar su reclamación de garantía.

El reemplazo del producto es su único remedio bajo esta Garantía. No seremos responsables de los cargos de

servicio o trabajo incurridos en la eliminación o sustitución de un producto o cualquier daño incidental o consecuente

de ningún tipo.

Usted reconoce y acepta que cualquier uso del producto para cualquier propósito que no sea el(los) uso(s)

especificado(s) indicado(s) en las instrucciones del producto es bajo su propio riesgo.

Esta Garantía le otorga derechos legales específicos, y también puede tener otros derechos que varían de un estado

a otro. Esta Garantía se rige por las leyes del Estado de Michigan, sin tener en cuenta las reglas relativas a los

conflictos de leyes. Los tribunales estatales ubicados en el condado de Oakland, Michigan, tendrán jurisdicción

exclusiva para cualquier disputa relacionada con esta garantía.

Horizon Global

47912 Halyard Dr. Suite 100

Plymouth, MI 48170

Para obtener las instrucciones de

producto más actualizadas, la

información de instalación y uso

analiza el código QR o llama

Reese 30944 Guía de instalación

Marca: Reese

Modelo: 30944

Tipo: Guía de instalación

Descargar PDF

informe

en otros idiomas

français: Reese 30944 Guide d'installation
English: Reese 30944 Installation guide

Reese 30944 Guía de instalación

Reese 30944 Guía de instalación

en otros idiomas

Artículos relacionados

Otros documentos