La-Z-Boy P16773 Manual de usuario

Marca: La-Z-Boy

Modelo: P16773

Categoría: Masajeadores

Tipo: Manual de usuario

__________

Rocker Recliner / Wall Recliner / Motion Sofas

________

Sillón reclinable y mecedor / Sillón reclinable para

espacios pequeños / Sillón con movimiento

________

Fauteuil inclinable à bascule /

Fauteuil inclinable mural / Canapés inclinables

Congratulations!

You are now the proud owner of a

stat e-of-the-art PowerReclineXR®or

PowerReclineXRw™product by La-Z-Boy.

You have just selected one of the

finest quality upholstered products

produced in the furniture industry,

backed by over 90 years of quality

manufacturing experience.

La-Z-Boy is proud of our

designs and craftsmanship and

knows you will feel the same as

you enjoy your new furniture’s

comfort and style.

Table of Contents

Important Safety Instructions ...................................... 4-5

PowerReclineXR®& PowerReclineXRw™Recliner

Assembly Instructions....................................................6-7

PowerReclineXR®with Massage & Heat

Assembly Instructions..................................................8-10

PowerReclineXR®Rocking Loveseat

Assembly Instructions..........................................................12-13

PowerReclineXRw™Motion Sofa

Assembly Instructions..........................................................14-17

Battery Backup Assembly Instructions..................................18

PowerReclineXR®& PowerReclineXRw™

Operating Instructions.........................................................20-21

PowerReclineXR®& PowerReclineXRw™ with Optional Hand Wand

Operating Instructions........................................................... 22-23

PowerReclineXR®with Massage and Heat

Operating Instructions...................................................24-26

PowerReclineXR®& PowerReclineXRw™

Troubleshooting...................................................................27-28

Furniture Placement Guide &

Cup Holder Operating and Cleaning Instructions........................29

IMPORTANT

Read the safety and other instructions before using

your PowerReclineXR®or PowerReclineXRw™product.

Keep this manual for future reference.

Disclaimer: The information and products featured in this manual may be

somewhat different from the product you purchased. La-Z-Boy reserves the right

to make substitutions that are equal in quality and performance.

• Only operate the power recline function when you are in a fully seated position.

• To avoid tipping the chair forward, bring the back completely upright and close the legrest before

you exit the chair.

• Do not use this product where aerosol (spray) products are being used or where oxygen

is being administered.

• Do not operate the unit until the back is installed and locked.

• Before moving the product, disconnect the electrical plug from the wall outlet and secure the

mechanism to prevent unexpected opening or movement. Never move the product by the mechanism,

legrest, handle or reclining back. Disconnect modular units.

• Do not attempt to disassemble or service the pump or motor; no serviceable parts are inside.

Contact your La-Z-Boy®dealer for service.

• Do not allow electrical cord to be pinched between moving parts or between the frame and the

floor. Do not place cord under carpet or in a location where it could become worn.

• Do not attempt to disconnect the power plug by pulling the power cord. Always hold the power

plug and pull it out.

• Do not use pillow, blanket, or other cover between occupant and chair surface when heat is engaged.

• Burns may result from improper use and care of internal heating pads. To avoid risk of burns, do not

use pins, do not allow heating pad area to become wet, and do not remove upholstery cover.

• Unplug the power cord immediately if you detect strange odors or fumes coming from the unit.

• This product is not intended to be used as a bed. Do not sleep in for an extended period.

• Keep hands, arms and body parts away from the open area between a reclined back and an upright

back on a motion sofa or modular. This area must remain clear at all times to provide unobstructed

movement and prevent injury that could occur when a reclined back is returning toward the

upright position.

• The PowerReclineXR®and PowerReclineXRw™units are intended for a single occupant not exceeding

300 pounds per seat. Do not operate an individual seat with more than one occupant in or on any part

of the individual seat.

• Double-insulated products are marked with the words “DOUBLE INSULATION” or “DOUBLE

INSULATED” and may include the symbol (square within a square). Do not attempt to ground

these products, which use two systems of insulation instead of grounding. Double-insulated

products should be serviced only by qualified service personnel, using replacement parts identical

to the original parts.

• If you give this product to someone else, include this Operating Instructions manual.

– To reduce the risk of product damage:

• To prevent damage to the power supply, do not plug in until instructed.

• Gently press the buttons during operation and avoid hitting the buttons with pointed or hard objects.

• Do not move the units while connected together. The purpose of the bracket system is to connect the

units and prevent them from being separated while on the floor. The bracket system does not provide

adequate structural support for the movement of connected units.

• Never operate the unit except when it is on its base in the upright position.

• Some units contain cup holders. Take care to prevent spilling of beverages, which could damage

the cover.

• After 1 minute of continuous operation, allow the back recline and legrest extension features

to rest for 9 minutes.

– To reduce the risk of electric shock, serious injury or death:

• Disconnect the electrical plug from the wall outlet before cleaning, moving, servicing or when

not in use for an extended period of time.

• Do not use this product if it is wet, in water, around water or any liquid. Do not handle the plug

or remote control with wet hands.

• To prevent suffocation keep plastic bags away from children.

• Plug directly into a wall outlet. Do not use an extension cord, adapter or surge protector.

• Keep cord out of reach of small children, and do not use where it may be a trip hazard.

– To reduce the risk of burns, fire, electric shock,

serious injury or death:

• Keep upholstery away from flames or lit cigarettes. Upholstery may burn rapidly, with toxic gas

and thick smoke. Fires that begin elsewhere in a home may spread and involve upholstery.

For your safety, always use a properly installed smoke detector with working batteries.

• Closely supervise children and disabled persons using this product.

• Sit down in the unit slowly. To avoid tip over, do not throw your weight against the back of the unit.

Move the unit into or out of the reclining position slowly, making sure that no children or pets are

in close proximity.

• This product has many moving parts, serious injury can occur if not used properly. Keep hands,

fingers and body parts away from the mechanism. To reduce the risk of head entrapment and other

injuries, keep children and pets away from openings and moving parts in and around furniture.

• Only the occupant should operate the unit. Never attempt to open the legrest by pulling on it.

• Do not stand, sit, or place extra weight on the arms, back or open legrest.

• To safely exit the unit and prevent a tripping hazard, bring the back upright and close the legrest.

• Do not use this product if it is damaged. Do not use attachments or substitute parts.

• This product is intended for indoor residential use only.

• Provide a clear path for operation of the back and legrest. Place tables and area rugs at a distance

to allow the legrest to fully extend without rubbing or interference.

• Check the condition of the power supplies, electrical cords, plugs, and connectors often. Keep the

power supplies and electrical cords away from heat sources. Never operate the unit with a damaged

power supply, electrical cord, plug, or connector. Contact your La-Z-Boy®dealer for service.

• Do not use unit if power control is damaged or wet. Do not use unit if the button activation switch

or hand wand has been exposed to, or dropped in, water or any liquid. Contact your La-Z-Boy®

dealer for service.

• This product is not intended for use as a health care device.

• Do not place containers with hot beverages in the cup holders. The furniture moves and

beverages may spill and cause injury. Do not place oversized or uncovered beverage containers

in the cup holders.

• Users of medical devices should contact their health care provider before using this product.

Do not use this product if you have poor circulation, are immobile, or cannot sense heat, except

as directed by your health care provider.

DANGER

WARNING

Important Safety Instructions:

Important: Read these instructions thoroughly before using.

Do not plug in until instructed.

Save These Instructions Save These Instructions

Important Safety Instructions:

Important: Read these instructions thoroughly before using.

Do not plug in until instructed.

NOTICE

Back Bracket

Body

Bracket

PowerReclineXR®& PowerReclineXRw™ Recliner

Assembly Instructions

Hand

Wand

FIGURE 1FIGURE 2

FIGURE 3FIGURE 4

FIGURE 5FIGURE 6

Plastic

Tie Power

Supply Box

120 Volt

Power Cord

Back

Bracket Locking

Lever

at 90

Degree

Angle

Locked

Position

– To reduce the risk of injury:

• Do not operate the unit until the back is installed and locked.

WARNING

3. Install the back.

•Lay the back across the arms of the chair. Turn the locking levers, located on the brackets attached

to the back (one on each side), to a 90 degree angle (FIGURE 4). Lift the back at a slight angle and

align the brackets on the back with the brackets on the body (FIGURE 2).

•Lower the back onto the body, making sure the back and body brackets are completely engaged.

-To make sure the back is properly installed with both sets of back and body brackets

engaged, stand behind the chair and twist the back from side to side. If one or both sides

move out of position the brackets are not engaged (FIGURE 3). Remove the back and repeat

the steps above.

-If you are unable to install the back properly, contact your La-Z-Boy®dealer for assistance.

•Lock the brackets by using a screwdriver to push down the locking levers (FIGURE 4).

4. Connect the power supply to the furniture. Align the power supply connector to the motor connector

routed behind the unit (FIGURE 5). Push the connectors together until fully seated and close the locking

cover to secure the connection.

5. Connect the 120 volt power cord to the power supply (FIGURE 6). Do not plug in until

instructed in the Operating Instructions.

6. If assembling a PowerReclineXR®Rocking Loveseat, proceed to the PowerReclineXR®

Rocking Loveseat Assembly Instructions.

7. If assembling a PowerReclineXR®or PowerReclineXRw™ chair, proceed to the Battery Backup

Assembly Instructions.

8. To remove the back, unplug the 120 volt power cord from the electrical outlet, and

disconnect the power supply connection behind the unit. Reverse the Assembly Instructions steps.

PowerReclineXR®& PowerReclineXRw™ Recliner

Assembly Instructions

NOTICE: Do not plug in until instructed.

1. Carefully cut the plastic tie holding the power supply box to the body bracket (FIGURE 1).

NOTE: The hand wand will also be tied to the body bracket for units ordered with the optional

hand wand.

2. For units with a hand wand, remove the hand wand from the bubble wrap, and lay the hand

wand on the seat.

Power Supply*

Make this

connection Make this

connection

Power

Supply

Motor Connector

Back and body brackets on this side are not

engaged. Remove the back and reinstall.

Illustrations show a PowerReclineXR®Recliner

*Power supply/connections will vary by style.

PowerReclineXR® with Massage & Heat

Assembly Instructions

Hand

Wand

FIGURE 1FIGURE 2

FIGURE 3FIGURE 4

FIGURE 5FIGURE 6

Plastic

Tie Power

Supply Box

Massage

Connectors

Back

Bracket Locking

Lever

at 90

Degree

Angle

Locked

Position

– To reduce the risk of injury:

• Do not operate the unit until the back is installed and locked.

WARNING

3. Install the back.

•Lay the back across the arms of the chair. Turn the locking levers, located on the brackets attached

to the back (one on each side), to a 90 degree angle (FIGURE 5). Route the massage and heating pad

cables between the rear of the seat and the metal rear rail (FIGURE 2). Do not allow the cables to

become pinched while installing the back.

•Lift the back at a slight angle and align the brackets on the back with the brackets on the

body (FIGURE 3).

•Lower the back onto the body, making sure the back and body brackets are completely engaged.

-To make sure the back is properly installed with both sets of back and body brackets

engaged, stand behind the chair and twist the back from side to side. If one or both sides

move out of position the brackets are not engaged (FIGURE 4). Remove the back and repeat

the steps above.

-If you are unable to install the back properly, contact your La-Z-Boy®dealer for assistance.

•Lock the brackets by using a screwdriver to push down the locking levers (FIGURE 5).

4. To access the connectors, gently roll the chair forward to rest on the arms and the top of the back.

The connectors are located at the back of the chair, under the rear seat.

5. Identify the electrical connectors (FIGURE 6).

•The rectangular red connectors are for the heating pad connection.

•The rectangular brown and black connectors are for the massage connection.

•The round black connector is for the power supply connection.

PowerReclineXR® with Massage & Heat

Assembly Instructions

NOTICE: Do not plug in until instructed.

1. Carefully cut the plastic tie holding the power supply box and the hand wand to the

body bracket (FIGURE 1).

2. Remove the hand wand from the bubble wrap, and lay the hand wand on the seat.

Heating Pad

Connectors

Back and body brackets on this side are not

engaged. Remove the back and reinstall.

Massage & Heat Cables

Metal Rear Rail

Back Bracket

Body

Bracket

Power Supply

Connector

(Assembly Instructions Continued)

Power Supply

Connector

PowerReclineXR® with Massage & Heat

Assembly Instructions

FIGURE 7FIGURE 8

FIGURE 9FIGURE 10

6. Align the red heating pad connectors and push the connectors together until locked (FIGURE 7).

7. Align the brown massage connector with the black massage connector and push the connectors

together until locked (FIGURE 8).

8. Gently rotate the chair back to the upright position so it is resting on its base. Do not allow the motor

connector to be pinched between the frame and the floor.

9. Connect the power supply to the chair. Align the power supply connector to the motor connector

routed behind the chair (FIGURE 9). Push the connectors together until fully seated and close the

locking cover to secure the connection.

10. Connect the 120 volt power cord to the power supply (FIGURE 10). Do not plug in until instructed

in the Operating Instructions.

11. Proceed to the Battery Backup Assembly Instructions.

12. To remove the back, unplug the 120 volt power cord from the electrical outlet, and disconnect the

power supply connection behind the chair. Reverse the Assembly Instructions steps.

Make this

connection

Make this

connection

Make this

connection

120 Volt Power Cord

Power Supply

Make this

connection

Motor Connector

(Page intentionally left blank)

PowerReclineXR®

Rocking Loveseat Assembly Instructions

FIGURE 1

Left Side (Sitting) Rocker Recliner

Front Attachment

Bracket

FIGURE 3FIGURE 4

Console

Front Side

Mount “U”

Bracket

Front Attachment

Bracket (Console)

Front Attachment

Bracket (Left Side

Sitting Rocker

Recliner)

Rear

Side

Mount

Bracket

Threaded

Studs

FIGURE 2

Right Side (Sitting) Rocker Recliner

8. The units must be disconnected before moving the loveseat. To disconnect the units, lift up the left front

corner of the right side (sitting) recliner approximately 3" to clear the front attachment bracket on the

console. Move the recliner to the side before returning it to the floor. Slide the right side (sitting) recliner

backward to disengage the back bracket on the console. Repeat these steps to disconnect the console

from the left side (sitting) recliner.

9. Proceed to the Battery Backup Assembly Instructions.

NOTICE: – To reduce the risk of product damage:

• Do not move the units while connected together. The purpose of the bracket system is to

connect the units and prevent them from being separated while on the floor. The bracket

system does not provide adequate structural support for the movement of connected units.

Rear Bracket

PowerReclineXR®

Rocking Loveseat Assembly Instructions

1. Place the furniture in the desired location; refer to Furniture Placement Guide.

2. Use a T-30 torx driver to loosen the threaded studs to approximately 1"; this measurement may vary

depending on the fabric and style. The threaded studs are located on the left side (sitting) of right side

(sitting) units.

3. Place the console (FIGURE 3) approximately 2" to the side of the left side (sitting) rocker recliner (FIGURE 1).

Position the console (with the threaded studs) slightly behind the recliner. Separate the fronts of the units

to be connected, about 6" apart. Pull the console forward until the threaded stud on the console engages

in the rear bracket on the recliner.

– To reduce the risk of serious injury:

• Provide a clear path for operation of the back and legrest. Place tables and area rugs

at a distance to allow the legrest to fully extend without rubbing or interference.

WARNING

– To reduce the risk of serious injury:

• The front of the unit must be raised to engage the front bracket. Please seek assistance if

you are unable to lift at least 21 pounds.

• Keep feet clear of the unit when lowering into position.

WARNING

4. Lift the front of the console approximately 3" off the ground, aligning it to the attachment bracket on the

left side (sitting) rocker recliner. Gently lower the threaded stud into the front attachment bracket (FIGURE 4).

Keep feet clear of the unit when lowering into position.

NOTE: Due to variations in upholstery and style, the threaded stud length may need to be adjusted to fit

into the attachment brackets or control gaps between units. Loosen or tighten the threaded studs to provide

adequate clearance.

5. Place the right side (sitting) rocker recliner (FIGURE 2) about 2" to the side of the console. Position the right

side (sitting) rocker recliner (with the threaded studs) slightly behind the console. Separate the fronts of

the units to be connected, about 6" apart. Pull the right side (sitting) recliner forward until the threaded

stud on the recliner engages in the rear bracket on the console.

NOTICE: – To reduce the risk of product damage:

• Lift from the side frame. Do not lift from the upholstery or bottom of the legrest.

– To reduce the risk of serious injury:

• The front of the unit must be raised to engage the front bracket. Please seek assistance if

you are unable to lift at least 21 pounds.

• Keep feet clear of the unit when lowering into position.

WARNING

6. Lift the front of the right side (sitting) recliner approximately 3" off the ground, aligning it to the attachment

bracket on the console. Gently lower the threaded stud into the front attachment bracket. Keep feet clear

of the unit when lowering into position.

7. Adjust the glides on the console to level the unit, if necess ary. Turn clockwise to lower and

counterclockwise to raise.

(Assembly Instructions Continued)

PowerReclineXRw™Motion Sofa

Assembly Instructions

PowerReclineXRw™Motion Sofa

Assembly Instructions

NOTICE: Do not plug in until instructed.

1. Remove all packaging from the unit and locate the boxed power supply and 120 volt power cord,

and bubble wrapped optional hand wand (if applicable) secured to the body bracket of the unit (FIGURE 1).

2. Carefully cut the plastic tie(s) securing the parts and move them away from the bracket. For units

with optional hand wands, remove the bubble wrap and place hand wand on the seat (FIGURE 2).

•Remove the power supply and 120 volt power cord from the box and set aside.

FIGURE 1FIGURE 2

FIGURE 3

FIGURE 5FIGURE 6

Hand

Wand

– To reduce the risk of injury:

• Do not operate the unit until the back is installed and locked.

WARNING

3. Install the back.

•Lay the backs face down on the seats. Starting with one back, turn the locking levers, located

on the brackets attached to the back (one on each side), 45 to 30 degrees from vertical (FIGURE 3).

•Hold the back at a slight angle to the seat and align the brackets on the back with the brackets

on the body (FIGURE 4).

•Rotate the back upright and lower the back onto the body (FIGURE 4), making sure the back and

body brackets are completely engaged.

-To make sure the back is properly installed with both sets of back and body brackets

engaged, stand behind the unit and twist the back from side to side. If one or both sides

move out of position the brackets are not engaged (FIGURE 5). Remove the back and

repeat the steps above.

-If you are unable to install the back properly, contact your La-Z-Boy®dealer for assistance.

•Lock both back brackets by using a screwdriver to push the locking levers down (FIGURE 6).

•Repeat this step for each back.

4.Choose a location for the power motion unit that is close to an electrical outlet.

FIGURE 4

Back

Bracket

Locking

Lever

at 45

Degrees

from

Vertical

Locked

Position

Back and body brackets on this side are not

engaged. Remove the back and reinstall.

(Assembly Instructions Continued)

Back

Bracket

45 Degrees

from

Vertical

Locking

Lever

Back Bracket

Body Bracket

Hand

Wand Plastic

Tie

Power Supply &

120 Volt Power Cord

PowerReclineXRw™Motion Sofa

Assembly Instructions

PowerReclineXRw™Motion Sofa

Assembly Instructions

FIGURE 7FIGURE 8

FIGURE 11

Back

Bracket

45 Degrees

from

Vertical

Locking

Lever

(Assembly Instructions Continued)

Motor Connectors

Base Rail

Lock

Washer

Upper Jam Nut

Lower Jam Nut

Adjustable Glide

– To reduce the risk of serious injury:

• Provide a clear path for operation of the back and legrest. Place tables and area rugs

at a distance to allow the legrest to fully extend without rubbing or interference.

FIGURE 9FIGURE 10

5. Adjust the glides to ensure a height that provides a clear path for operation of the legrest. Each glide is

attached to the base rail by one jam nut and one lock washer on top of the base rail, and one jam nut

on the bottom of the base rail.

•To extend the glide, loosen the upper jam nut by rotating clockwise. Turn the lower jam nut

clockwise to the desired height.

•Tighten the upper jam nut by rotating counterclockwise.

•Repeat steps one and two for each adjustable glide on the unit, if needed.

•Repeat this procedure, as necessary, to adjust the front height of the unit and level it.

6. Locate the motor connector, one behind each reclining seat (FIGURE 7). Connect the Y-cable to the

motor connectors and to the power supply.

•Align one motor connector to a long lead Y-cable connector, push the connectors together until

seated and close the locking cover to secure the connection (FIGURE 8). Repeat this for the other

motor connector and Y-cable long lead. Then align the short lead of the Y-cable to the power supply

connector, push the connectors together until seated and close the locking cover to secure the

connection (FIGURE 9).

7. Connect the 120 volt power cord to the power supply (FIGURE 10). Do not plug in until instructed in

the Operating Instructions.

8. Proceed to the Battery Backup Assembly Instructions.

To Remove a Back:

1. Unplug the 120 volt power cord from the electrical outlet and disconnect the power supply from

the Y-cable.

2. Taking care not to damage the cover, insert a screwdriver between the arm and back and engage

the locking lever on the back bracket (FIGURE 11).

3. Push up on the locking lever until the lever is at 45 to 30 degrees from vertical (FIGURE 11).

4. Repeat steps 2 and 3 for the other side of the back, inserting the screwdriver between

the rear post and back.

5. The back is free to remove at this point. Lift up on the back to remove.

WARNING

Y-Cable Long Leads

Make this

connection

Power Supply

Y-Cable Short Lead

Make these

connections

Make this

connection

Power Supply 120 Volt Power Cord

Battery Backup Assembly Instructions

NOTICE:

The performance of the built-in battery backup cannot be guaranteed. If you require continuing

use during a power outage, you should purchase a separate battery backup system. Contact

your La-Z-Boy®dealer for more information.

To reduce battery consumption, the massage and heat features are blocked and unavailable

when the battery backup is in use. Additionally, the operating speed is reduced to decrease

energy consumption.

Always maintain constant even pressure on the button when operating on battery backup to

reduce the energy consumption.

The battery backup is located in the power supply and uses two 9-volt alkaline

batteries (not included).

1. Unplug the 120 volt power cord from the electrical outlet, and disconnect the power supply

connector from either the Y-cable connector or motor connector, whichever comes with the product.

2. Depending on the style purchased, the battery compartment is located in either the bottom or side

of the power supply. Locate the battery compartment and slide the battery cover over to access

the battery compartment. Your power supply will look like FIGURE 1 or FIGURE 2.

3. Snap the connection caps on the battery terminals. Place the batteries in the power supply.

4. Slide the battery cover(s) over the batteries.

5. Proceed to the Operating Instructions.

Power

Supply (2) 9-Volt

Alkaline Batteries

PowerReclineXR®& PowerReclineXRw™

Supply Specifications:

Input: 100-240V~, AC 50/60 Hz 1.5A

Output: 29V, DC 2A

Battery

Cover

Replace the power supply batteries every six months and after

each power failure use. Under normal conditions, the battery

backup will operate the chair two times, but this performance

cannot be guaranteed.

FIGURE 1

Power Supply Specifications:

Input: AC 100V-240V~50/60Hz, 1.6A

Output: DC 29V 2A

FIGURE 2

Note: Power supplies vary by style and date of manufacturer.

Power Supply

(2) 9-Volt

Alkaline Batteries

Battery

Cover

(Page intentionally left blank)

PowerReclineXR®& PowerReclineXRw™

Operating Instructions

PowerReclineXR®& PowerReclineXRw™

Operating Instructions

–To reduce the risk of electric shock, serious

injury or death:

• Plug directly into a wall outlet. Do not use an extension cord, adapter or surge protector.

DANGER

– To reduce the risk of serious injury:

• Sit down in the unit slowly. To avoid tip over, do not throw your weight against the back

of the unit. Move the unit into or out of the reclining position slowly, making sure that

no children or pets are in close proximity.

• Keep hands, arms and body parts away from the open area between a reclined back and

an upright back on a motion sofa or modular. This area must remain clear at all times to

provide unobstructed movement and prevent injury that could occur when a reclined back

is returning toward the upright position.

• The PowerReclineXR®and PowerReclineXRw™units are intended for a single occupant not

exceeding 300 pounds per seat. Do not operate an individual seat with more than one

occupant in or on any part of the individual seat.

• To safely exit the unit and prevent a tripping hazard, bring the back upright

and close the legrest.

WARNING

To avoid product damage, the back recline and legrest extension features should not be operated continuously

for extended periods of time. After 1 minute of continuous operation, allow these features to rest for 9 minutes.

Plug the power cord directly into a wall outlet. Make sure there is enough slack in the cord running

from the chair to the outlet to allow for rocking and reclining. Never stretch or strain a cord.

The PowerReclineXR®and PowerReclineXRw™offers three reclining options:

• Only recline the back. When the back is reclined, the PowerReclineXR® chair can be rocked.

• Only extend the legrest. When the legrest is extended, the chair body tilts backward.

• Operate both the back recline and legrest extension simultaneously.

Back Recline:

Press and hold down the top, front button. Release the button when you have reached a comfortable position.

To return the back to the upright position, press and hold down the top, back button. Release the button

when you have reached a comfortable position, or when the back is fully upright.

Legrest Extension:

Press and hold down the bottom, front button. Release the button when you have reached a comfortable position.

To return the legrest to the closed position, press and hold down the bottom, back button. Release the

button when you have reached a comfortable position, or when the legrest is fully closed.

Back Recline and Legrest Extension:

The back recline and legrest extension can move simultaneously by pressing and holding both front buttons

at the same time, releasing the buttons when you have reached a comfortable position.

The reclined back and extended legrest can also be returned simultaneously by pressing and holding both

back buttons at the same time, releasing them when you have reached a comfortable position, or the back is

fully upright and the legrest is fully closed.

The function of each button is explained in greater detail on the following page.

Unplug the power supply if you are going to be away from your residence for an extended period of time.

NOTICE: After 1 minute of continuous operation, allow the back recline

and legrest extension features to rest for 9 minutes.

Press and hold down the top, back button to return the

back to the upright position. Release the button to stop

the back in any reclined position or when fully raised.

Back

Return

Legrest

Extension

Back

Recline

Charging

USB Port

Press and hold down the top, front button to recline

the chair back. Release the button to stop the back

in any reclined position or when fully reclined.

Press and hold down the bottom, back button to

close the legrest. Release the button to stop the

legrest in any extended position or when fully closed.

Press and hold down the bottom, front button to

extend the legrest and tilt the chair body backward.

Release the button to stop the legrest in any

extended position or when fully raised.

USB Charging Port Instructions

Plug a small portable electronic device into the USB charging port. The USB port is for charging only

and does not have data transferring capabilities.

USB Output Specifications:

5VDC, 2.1A

Legrest

Return

Press and hold down the

back top and bottom

buttons to raise the back

and close the legrest and

return the chair body.

Release the buttons to

stop the chair in any

position or when the

back is fully raised and

the legrest is fully closed.

Press and hold down

the front top and

bottom buttons to

recline the back and

extend the legrest

and tilt the chair body

backward. Release

the buttons to stop the

chair in any position

or when the back is

fully reclined and the

legrest is fully raised.

– To reduce the risk of serious injury:

• Do not use unit if power control is damaged or wet. Do not use unit if the button activation

switch or hand wand has been exposed to, or dropped in, water or any liquid. Contact your

La-Z-Boy®dealer for service.

WARNING

PowerReclineXR®& PowerReclineXRw™

with Optional Hand Wand Operating Instructions

– To reduce the risk of electric shock, serious

injury or death:

• Plug directly into a wall outlet. Do not use an extension cord, adapter or surge protector.

DANGER

– To reduce the risk of serious injury:

• Sit down in the unit slowly. To avoid tip over, do not throw your weight against the back

of the unit. Move the unit into or out of the reclining position slowly, making sure that

no children or pets are in close proximity.

• Keep hands, arms and body parts away from the open area between a reclined back and an

upright back on a motion sofa or modular. This area must remain clear at all times to provide

unobstructed movement and prevent injury that could occur when a reclined back is

returning toward the upright position.

• The PowerReclineXR®and PowerReclineXRw™units are intended for a single occupant

not exceeding 300 pounds per seat. Do not operate an individual seat with more than

one occupant in or on any part of the individual seat.

• To safely exit the unit and prevent a tripping hazard, bring the back upright

and close the legrest.

WARNING

To avoid product damage, the back recline and legrest extension features should not be operated

continuously for extended periods of time. After 1 minute of continuous operation, allow these features

to rest for 9 minutes.

Plug the power cord directly into a wall outlet. Make sure there is enough slack in the cord running

from the chair to the outlet to allow for rocking and reclining. Never stretch or strain a cord.

The PowerReclineXR®and PowerReclineXRw™offers three reclining options:

• Only recline the back. When the back is reclined, the PowerReclineXR® chair can be rocked.

• Only extend the legrest. When the legrest is extended, the chair body tilts backward.

• Operate both the back recline and legrest extension simultaneously.

To recline, press and hold down one of the three reclining option buttons on the right side of the

hand wand. Release the button when you have reached a comfortable position.

To return to the upright position, press and hold down one of the three return buttons on the left

side of the hand wand. Release the button when you have reached a comfortable position, or

when the back is fully upright and the legrest is fully closed.

The function of each hand wand button is explained in greater detail on the following page.

Unplug the power supply if you are going to be away from your residence for an extended period of time.

NOTICE: After 1 minute of continuous operation, allow the back recline

and legrest extension features to rest for 9 minutes.

PowerReclineXR®& PowerReclineXRw™

with Optional Hand Wand Operating Instructions

– To reduce the risk of serious injury:

• Do not use unit if power control is damaged or wet. Do not use unit if the button activation

switch or hand wand has been exposed to, or dropped in, water or any liquid. Contact your

La-Z-Boy®dealer for service.

WARNING

Press and hold the

button down to return

the back to the upright

position. Release the

button to stop the back

in any reclined position

or when fully raised.

Press and hold the

button down to close

the legrest and return

the chair body. Release

the button to stop the

legrest in any extended

position or when

fully closed.

Press and hold the

button down to raise

the back and close the

legrest and return the

chair body. Release

the button to stop the

chair in any position or

when the back is fully

raised and the legrest

is fully closed.

Press and hold the

button down to recline

the chair back. Release

the button to stop the

back in any reclined

position or when

fully reclined.

Press and hold the

button down to extend

the legrest and tilt the

chair body backward.

Release the button to

stop the legrest in any

extended position or

when fully raised.

Press and hold the

button down to recline

the back, extend

the legrest and tilt the

chair body backward.

Release the button to

stop the chair in any

position or when the

back is fully reclined

and the legrest is

fully raised.

TO OPERATE HEAT OR MASSAGE:

•

Press the MSG button to start and stop the massage.

•

Press the button to select your massage mode. The button light will change to green for

Constant massage, amber for Wave massage and red for Pulse massage. The massage program

will run for 15 minutes, then shut off. When restarted, massage will operate in the last mode

selected before shut off.

•

Press the button to select the massage intensity. The button light will change to green for

Low intensity, amber for Medium intensity, and red for High intensity. The chair automatically

resets to the Low intensity setting when massage is restarted.

•

Heat may be used with or without massage. Press the HEAT button to start and stop the heat.

The button light will change to amber for Low heat, and red for High heat. The heat will operate

for 15 minutes, then shut off. The chair automatically resets to the Low heat setting when heat

is restarted.

•

When you are ready to leave the chair, turn the massage system off by pressing the MSG button.

The button light will change to blue. Turn the heat system off by pressing the HEAT button until the

indicator light changes to blue.

The massage and heat systems shut off automatically after approximately 15 minutes of operation.

If you immediately restart the systems, they will operate for an additional 15 minutes and then shut

off for a 30-minute cool down. You can restart the systems after the 30-minute cool down period.

If you attempt to restart the massage or heat function before the cool down period is over, the MSG

or HEAT button will flash for 5 seconds indicating the cool down period.

NOTE:

Activated massage and heat functions are temporarily suspended when the BACK,

LEGREST or BOTH buttons are in use.

•

Following a power outage or power interruption, the chair will return to the off setting

when power is restored.

Unplug the power supply if you are going to be away from your residence for an extended period of time.

PowerReclineXR®with Massage & Heat

Operating Instructions

– To reduce the risk of electric shock, serious

injury or death:

• Plug directly into a wall outlet. Do not use an extension cord, adapter or surge protector.

DANGER

– To reduce the risk of serious injury:

• Sit down in the unit slowly. To avoid tip over, do not throw your weight against the back

of the unit. Move the unit into or out of the reclining position slowly, making sure that

no children or pets are in close proximity.

• The PowerReclineXR®units are intended for a single occupant not exceeding 300 pounds

per seat. Do not operate an individual seat with more than one occupant in or on any

part of the individual seat.

• To safely exit the unit and prevent a tripping hazard, bring the back upright

and close the legrest.

WARNING

To avoid product damage, the back recline and legrest extension features should not be operated

continuously for extended periods of time. After 1 minute of continuous operation, allow these features

to rest for 9 minutes.

Plug the power cord directly into a wall outlet. Make sure there is enough slack in the cord running

from the chair to the outlet to allow for rocking and reclining. Never stretch or strain a cord.

The PowerReclineXR®offers three reclining options:

• Only recline the back. When the back is reclined, the chair can be rocked.