Transcripción de documentos

Technical Specifications Interface: USB 2.0; 1.1-compatible ® Converters: Wolfson WM8740 Dynamic Range: 110 dB maximum THD+N: 0.00003% maximum Headphone Output (at 1 kHz): 190 mW (32 Ω); 210 mW (16 Ω) Headphone Drive Ability: 16–100 Ω (1/8” / 3.5mm); 100–600 Ω (1/4” / 6.35mm) Analog Inputs: (1) 1/8” (6.35mm) line-level Digital Inputs: (1) USB 2.0 port Analog Outputs: (1) RCA stereo pair; (1) 1/8” (3.5mm) headphone; (1) 1/4” (6.35mm) headphone ® ® Digital Outputs: (1) S/PDIF optical; (1) coaxial; Dolby and DTS pass-through Sampling Rates: 44.1, 48, 88.2, 96, 176.4, 192 kHz Power: via USB connection or via power adapter (12 VDC, 1 A, centerpositive, sold separately) Dimensions (WxDxH): 3.7” x 3.6” x 1.1” / 94 mm x 91 mm x 27 mm Weight: 0.5 lbs. / 0.21 kg Specifications are subject to change without notice. User Guide (English) For more information about this product (system requirements, compatibility information, etc.), product registration, or product support, visit m-audio.com. For safety and warranty information, visit m-audio.com/warranty. Package Contents: Super DAC, mini-USB cable, RCA cable, User Guide Windows users: Visit m-audio.com/drivers to download the necessary Windows drivers for Super DAC. Safety & Compliance Notices: Notice Concerning FCC Regulations: You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (a) Reorient or relocate the receiving antenna; (b) move this unit; (c) increase the separation between the equipment and receiver; (d) connect the equipment into an outlet on a circuit different from that to which the receiver is connected; (e) be sure that all cables are properly shielded, using a choke or ferrite where appropriate; (f) consult the dealer or an experienced radio/television technician for help. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. For best audio quality, avoid using this device in a high RFradiated environment. RSS Statement for Canadian models: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device This unit does not exceed the Class B limits for radio noise emission from digital apparatus set out in the radio interference regulations of the Canadian Department of Communications. ESD/EFT Warning: This unit may contain a microcomputer for signal processing and control functions. In very rare situations, severe interference, noise from an external source, or static electricity may cause it to lock up. In the unlikely event that this should happen, turn off the unit, wait at least five seconds, and then turn it back on again. In an environment with radio frequency interference, the unit may malfunction and resume normal operation after removal of the interference. Trademarks and Licenses: M-Audio is a trademark of inMusic Brands, Inc., registered in the U.S. and other countries. Wolfson is a trademark of Wolfson Microelectronics PLC. Dolby is a registered trademark of Dolby Laboratories. DTS is a registered trademark of DTS, Inc. Windows is a registered trademark of Microsoft Corporation in the United States and other countries. All other product or company names are trademarks or registered trademarks of their respective owners. 3. Line Input: Use a standard 1/8” (3.5mm) cable to connect this analog input to the analog output of your audio source. This input will receive an analog signal when the input selector is set to the “up” position. 4. Headphone Outputs: Connect standard 1/8” (3.5mm) or 1/4” (6.35mm) stereo headphones to either or both of these analog outputs. Remember to set the output selector to the “up” position. 5. Volume Dial: Use this dial to control the volume of all outputs. 6. Power Indicator: This light illuminates when Super DAC is powered on. 7. Analog Output Indicator: This light illuminates when Super DAC is successfully sending an analog signal out of its left/right analog outputs. 8. Sampling Rate Indicators: One of these lights illuminates to indicate which sampling rate Super DAC is currently using: 44.1, 48, 88.2, 96, 176.4, or 192 kHz. 9. Power Input: Use a power adapter (12 VDC, 1 A, center-positive, sold separately) to connect this input to your power source. If Super DAC’s USB port is connected to a computer (powered on), the connection will supply the necessary power; a power adapter is not required in this case. 10. USB Port: Use the included mini-USB cable to connect this port to a USB port on your computer (powered on). The connection will supply the necessary power to Super DAC. This port will receive a digital signal from 10 your computer when the input selector is set to the “down” position. 11 12 13 13 11. S/PDIF Output: Use a standard S/PDIF cable to connect this digital output to the S/PDIF input of a receiver or playback device. 1. Output Selector: Set this switch to the “up” position to send the audio to the headphone outputs. Set this switch to the “down” position to send the 12. Coaxial Output: Use a standard coaxial cable to connect this digital audio to the S/PDIF, coaxial, and analog outputs. output to the coaxial input of a receiver or playback device. 2. Input Selector: Set this switch to the “up” position to select an analog input 13. Analog Outputs: Use a standard stereo RCA cable to connect these analog outputs to the stereo RCA inputs of a playback device. source. Set this switch to the “down” position to select a digital input. source. 1 2 3 4 5 6 4 8 9 7 3. Entrada de línea: Utilice un cable estándar de 3,5 mm (1/8 pulg.) para conectar esta entrada analógica a la salida analógica de su fuente de audio. Esta entrada recibe una señal analógica cuando el selector de entrada está ajustado a la posición “hacia arriba”. Para más información acerca de este producto (requisitos de sistema, información de compatibilidad, etc.), registro o soporte del producto, visite m-audio.com. Para información sobre la seguridad y la garantía, visite m-audio.com/warranty. 4. Salidas para auriculares: Conecte auriculares estéreo estándar de 3,5 mm (1/8 pulg.) o de 6,35 mm (1/4 pulg.) a estas dos salidas analógicas o a una de ellas. Recuerde ajustar el selector de salida a la posición “hacia arriba”. Contenido del paquete: Super DAC, cable mini-USB, cable RCA, guía del usuario 5. Usuarios de Windows: Visitar m-audio.com/drivers para descargar los drivers de Windows necesarios para Super DAC. Cuadrante de volumen: Utilice este cuadrante para controlar el volumen de todas las salidas. 6. Indicador de encendido: Esta luz se enciende cuando el Super DAC está encendido. 7. Indicador de salida analógica: Esta luz se enciende cuando el Super DAC envía exitosamente una señal de salida analógica a sus salidas analógicas izquierda/derecha. 8. Indicadores de frecuencia de muestreo: Una de estas luces se enciende para indicar qué frecuencia de muestreo está utilizando el Super DAC en ese momento: 44,1, 48, 88,2, 96, 176,4 o 192 kHz. 9. Entrada de corriente: Use un adaptador de corriente (12 VCC, 1 A, centro positivo, que se vende por separado) para conectar esta entrada a su fuente de alimentación. Si el puerto USB del Super DAC está conectado a un ordenador (encendido), la conexión suministra la corriente necesaria y en este caso no se requiere un adaptador de corriente. Guía del usuario (Español) 1 2 3 4 5 6 7 4 8 9 10 11 12 13 13 10. Puerto USB: Utilice el cable mini-USB incluido para conectar este puerto a un puerto USB disponible en su ordenador (encendido). La conexión suministra al Super DAC la corriente necesaria. Este puerto recibe una señal digital del ordenador cuando el selector de entrada está ajustado a la posición “hacia abajo”. 1. Selector de salida: Ajuste este interruptor en la posición “hacia arriba” para enviar 11. Salida S/PDIF: Utilice un cable S/PDIF estándar para conectar esta salida digital a la el audio a las salidas para auriculares. Ajuste este interruptor en la posición “hacia entrada S/PDIF de un dispositivo receptor o de reproducción. abajo” para enviar el audio a las salidas S/PDIF, coaxial y analógica. 12. Salida coaxial: Utilice un cable coaxial estándar para conectar esta salida digital a la 2. Selector de entrada: Ajuste este interruptor a la posición “hacia arriba” para entrada coaxial de un dispositivo receptor o de reproducción. seleccionar una fuente de entrada analógica. Ajuste este interruptor a la posición 13. Salidas analógicas: Use un cable RCA estéreo estándar para conectar estas salidas “hacia abajo” para seleccionar una fuente de entrada digital. analógicas a las entradas RCA de un dispositivo de reproducción.