Fibaro FGWPB-111 | FGWPB-121 Short Manual

Tipo
Short Manual
EN
Basic activation of the device
FIBARO WALL PLUG
FGWPB-111
Specifications
Power supply:
Rated load
(continuous load):
To be used with B type sockets:
Operating temperature:
Dimensions (Width x Height x Depth):
120V AC, 50/60Hz
15A - resistive loads
8A - incandescent loads
15A - inductive general purpose
(cosφ = 0.75-0.8)
360VA - inductive (Pilot Duty)
(cosφ < 0.35)
373W - motor
3A - electronic ballasts
NEMA 5-15 - max load 15A
32-104°F
2.32” x 2.32” x 2.01”
For full instruction manual and technical
specification please visit our website:
manuals.fibaro.com/en/wall-plug-us
IMPORTANT
Read the manual before attempting
to install the device!
1) Plug the device into a socket nearby the main Z-Wave controller.
2) Set the main Z-Wave controller in add mode.
3) Quickly, triple click the button located on the casing.
4) Wait for the device to be added to the system.
5) Successful adding will be confirmed by the controller.
6) Plug a device you want to control into the Wall Plug.
7) Test the device by turning it on and off using the button.
FIBARO Wall Plug is a remotely controlled plug-in switch with the
ability to measure power and energy consumption.
It uses a LED frame to visualize the current load and operating mode
with color changing illumination.
Our smart plug makes it possible to control electrical devices in a
convenient and maintenance-free way.
105449010101
Button
This device complies with Part 15 of the FCC Rules
Operation is subject to the following two conditions:
1. This device may not cause harmful interference
2. This device must accept any interference received, including
interference that may cause undesired operation. This equipment
has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes and modifications not expressly approved by the manufac-
turer or registrant of this equipment can void your authority to
operate this equipment under Federal Communications Commis-
sion’s rules.
Industry Canada (IC) Compliance Notice
This device complies with Industry Canada license-exempt RSSs.
Operation is subject to the following two conditions: (1) this device
may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired
operation of the device.
Legal Notices
All information, including, but not limited to, information regarding the
features, functionality, and/or other product specification are subject
to change without notice. Fibaro reserves all rights to revise or
update its products, software, or documentation without any
obligation to notify any individual or entity.
Fibaro and Fibar Group logo are trademarks of Fibar Group S.A. All
other brands and product names referred to herein are trademarks of
their respective holders.
Disclaimer
The information contained herein is provided in connection with
Fibaro products. No license, expressed or implied by estoppel or
otherwise, to any intellectual property rights is granted by this
documents.
This documentation may contain references to third-party sources of
information, hardware or software, products or services (“collectively
the “Third-Party Products or Services”). Fibaro does not control the
Third-Party Products or Services and is not responsible for any
Third-Party Products or Services.
Except as provided above or except to the extent prohibited by
applicable law, Fibaro shall not be liable for any incidental or
consequential damages caused by the breach of any express or
implied warranty. Fibaro assumes no liability whatsoever, and Fibaro
disclaims any express or implied warranty, relating to the sale and/or
use of the Fibaro products, including, but to limited to, liabilities
and/or warranties relating to fitness for a particular purpose,
merchantability, and/or infringement of any patent, copyright and/or
other intellectual property right.
Except to the extent prohibited by applicable law, Fibaro’s liability
shall not exceed the price paid for the Fibaro products from direct,
indirect, special, incidental or consequential damages resulting from
the sue of the products, its accompanying software, or product
specifications, manuals, installation guides and/or any other
documentation.
Some states, provinces or jurisdictions do not allow the exclusion or
limitation of incidental or consequential damages or other limitations
on warranties, so the above limitations or exclusion may not apply to
you. You may also have other rights that vary from state to state or
province to province.
This product is not a toy. Keep away from children and animals!
Do not expose this product to moisture, water or other liquids.
This product is designed for indoor use only. Do not use outside!
FR
FIBARO WALL PLUG
FGWPB-111
Pour le manuel et les spécifications
techniques, s'il vous plait, visiter notre
site Web:
manuals.fibaro.com/fr/wall-plug-us
IMPORTANT
Lisez le manuel avant de tenter
d'installer l'appareil!
FIBARO Wall Plug est une prise interrupteur contrôlable à
distance avec la capacité de mesurer la consommation d'énergie et
de puissance.
Elle utilise un cadre LED pour visualiser la charge et le mode de
fonctionnement actuel avec un éclairage changeant de couleur.
Notre prise intelligente permet de contrôler les appareils électriques
de manière pratique et sans entretien.
Installation du dispositif
1) Mettez le capteur à proximité du contrôleur principal Z-Wave.
2) Mettez le contrôleur de Z-Wave en mode inclusion.
3) Cliquez rapidement 3 fois sur le bouton situé sur le boitier.
4) Attendez que le dispositif soit ajouté dans le système.
5) L’ajout correct sera confirmé par le contrôleur.
6) Branchez l’appareil que vous voulez contrôler sur le Wall Plug.
7) Testez le dispositif en commutant en marche et arrêt en utilisant
le bouton.
Bouton
Spécifications
Alimentation:
Charge nominale
(charge continue):
Peut être utilisé avec des type B:
Température de fonctionnement:
Dimensions (Largeur x Hauteur x Profondeur):
120V AC, 50/60Hz
15A - charges résistives
8A - charges incandescentes
15A - usage général inductif
(cosφ = 0.75-0.8)
360VA - inductif (Pilot Duty)
(cosφ < 0.35)
373W - moteur
3A - ballasts électroniques
NEMA 5-15 - charge maximale 15A
0-40°C (32-104°F)
59 x 59 x 51 mm
L’article n’est pas un jouet. Tenez les enfants et les animaux
éloignés!
Ne pas exposer ce produit à l'humidité, à l'eau ou à d'autres
liquides.
Ce produit est conçu pour une utilisation à l'intérieur seulement.
Ne pas l’utiliser à l'extérieur!
Avis de conformité aux normes d’Industrie Canada (IC)
Cet appareil est conforme aux normes d’exemption de licence RSS
d’Industry Canada. Son fonctionnement est soumis aux deux
conditions suivantes: (1) cet appareil ne doit pas causer d’interfé-
rence et (2) cet appareil doit accepter toute interférence, notamment
les interférences qui peuvent affecter son fonctionnement.
ES
FIBARO WALL PLUG
FGWPB-111
Para obtener el manual completo de
instrucciones y especificaciones
técnicas, por favor visite nuestra web:
manuals.fibaro.com/es/wall-plug-us
IMPORTANTE
¡Lea el manual antes de intentar
instalar el dispositivo!
FIBARO Wall Plug es un interruptor de pared remotamente
controlado con la capacidad de medir el poder y el consumo de
energía.
Usa un marco LED para visualizar la carga corriente y el modo de
operaciones con el color que cambia la iluminación.
Nuestro Smart Plug hace posible controlar dispositivos eléctricos de
un modo conveniente y sin necesidad de mantenimiento.
Activación básica del dispositivo
1) Enchufe el dispositivo en un enchufe cercano al controlador
Z-Wave principal.
2) Active el controlador Z-Wave en modo de inclusión.
3) Rápidamente, pulse tres veces el botón ubicado sobre la carcasa.
4) Espere a que el dispositivo sea añadido al sistema.
5) Una inclusión satisfactoria será confirmada por el controlador.
6) Enchufe un aparato que desee controlar en el Wall Plug.
7) Compruebe el dispositivo, encendiendo y apagándolo mediante
el botón.
Botón
Especificaciones
Alimentación:
Carga nominal
(carga continua):
Para usar con sockets tipo B:
Temperatura de trabajo:
Dimensiones (Ancho x Alto x Profundidad):
120V AC, 50/60Hz
15A - carga resistente
8A - cargas incandescentes
15A - objetivo inductivo general
(cosφ = 0.75-0.8)
360VA - inductivo (Pilot Duty)
(cosφ < 0.35)
373W - motor
3A - balastros electrónicos
NEMA 5-15 - carga máxima 15A
0-40°C (32-104°F)
59 x 59 x 51 mm
Este producto no es un juguete. Manténgalo lejos del alcance
de los niños y animales!
No exponga este producto a humedad, agua u otros líquidos.
Este producto está diseñado para uso en interiores solamente.
¡No lo utilice en exteriores!
PT
FIBARO WALL PLUG
FGWPB-111
Para descarregar o manual de utilizador
complete e especificações por favor visite
a nossa página:
manuals.fibaro.com/pt/wall-plug-us
IMPORTANTE
Leia o manual antes de tentar
instalar o dispositivo!
FIBARO Wall Plug é uma tomada comandada capaz de medir o
consumo e potência dos equipamentos ligado a ele.
O Wall Plug possui LED indicador de potência, as cores mudam de
acordo com o consumo dos equipamentos que estão ligados.
Nossa tomada inteligente permite controlar seus dispositivos sem a
necessidade de nenhuma adaptação ou manutenção.
Ativação básica do dispositivo
1) Ligue o módulo numa tomada nas proximidades do controlador
Z-Wave.
2) Coloque o controlador Z-Wave em modo de inclusão.
3) Clique rapidamente 3 vezes o botão, localizado no dispositivo.
4) Aguarde que o módulo seja adicionado ao sistema.
5) Uma adição com sucesso é confirmada pelo controlador.
6) Ligue o dispositivo que pretende controlar ao módulo de tomada.
7) Teste o dispositivo ligando-o e desligando-o utilizando o botão.
Botão
Especificações
Alimentação:
Carga nominal
(carga contínua):
Para usar com soquete tipo B:
Temperatura de utilização:
Dimensões (Largura x Altura x Profundidade):
120V AC, 50/60Hz
15A - para cargas resistivas
8A - para carga incandescente
15A - para carga indutiva em geral
(cosφ = 0.75-0.8)
360VA - carga indutiva (Pilot Duty)
(cosφ < 0.35)
373W - motor
3A - balastros eletrônicos
NEMA 5-15 - corrente máxima de 15A
0-40°C (32-104°F)
59 x 59 x 51 mm
Este produto não é um brinquedo. Mantenha longe de crianças
e animais!
Não exponha este produto a humidade, água ou outros
líquidos.
Este produto foi projetado apenas para uso interno. Não use no
exterior!
Limited warranty - United States
This limited warranty is provided by Fibar USA, LLC (the “Company”), 1040 E.
Lake Ave., Glenview, Illinois 60025, as the sole and exclusive remedy offered to a
purchaser (the “Customer”) of the products (the “Products”) for any alleged defects
in any of the Products. The warranty is subject to all terms sets forth below.
1. LIMITED WARRANTY:
Subject to the limitations of section 2, the company warrants that the products sold
by the company to the customer will be free from defects in material and
workmanship under normal use and regular service and maintenance for a period
of one (1) year from the date of purchase of the products. The one-year period may
be referred to as the “limited warranty period”.
This is the sole and exclusive warranty given by the company with respect to the
products and is in lieu of and excludes all other warranties, express or implied,
arising by operation of law or otherwise, including without limitation, any implied
warranties of merchantability, fitness for a particular purpose, non-infringement
and the implied condition of satisfactory quality.
The product is not, is not intended to function or be used as, should not be used as,
and shall not be deemed to be, an alarm system or home security system. The
product’s intended use shall not include use as an alarm system or home security
system.
This limited warranty does not extend to any losses or damages due in whole or in
part to misuse, accident, abuse, neglect, normal wear and tear, negligence (other
than the Company’s), unauthorized modification or alteration, use beyond rated
capacity, unsuitable power sources or environmental conditions, improper
installation, repair, handling, maintenance or application, third party actions or
omissions (whether as an agent or apparent agent of the Company), criminal acts,
or any other cause not the direct fault of the Company.
2. LIMITATION OF REMEDY:
If within the limited warranty period, the Customer discovers any covered warranty
defects and notifies the Company within thirty (30) days of such discovery,
pursuant to the Claims Procedure in Section 4 below, the Company shall, at its
option and as the Customer’s exclusive remedy, repair or replace F.O.B. point of
manufacture.
The remedies set forth in this limited warranty are exclusive. The sole and
exclusive remedy for breach of any warranty hereunder shall be limited to repair or
replacement of the products.
In the event that the product cannot be repaired or replaced, the company reserves
the right to substitute a product of similar technical parameters.
The company will not refund the purchase price of the original product.
Failure by the Customer to give such written notice within the thirty (30) day time
period shall be deemed an absolute and unconditional waiver of the Customer’s
claim for such covered defects. All costs and expenses of dismantling,
reinstallation and freight, including the time of the Company’s personnel and
representatives for site travel and diagnosis under this limited warranty, shall be
borne by the Customer unless accepted in writing by the Company. Products
repaired or replaced during the limited warranty period shall be covered by the
foregoing limited warranty for the remainder of the limited warranty period.
The Customer assumes all other responsibility for any loss, damage, or injury to
persons or property arising out of, connected with, or resulting from the use of
Products, either alone or in combination with other products/components.
3. LIMITATION OF LIABILITY:
In no event, regardless of the form of the claim or cause of action (whether based
in contract, infringement, negligence, strict liability, other tort or otherwise), shall
the company’s liability to the customer or any third party exceed the price paid by
the customer for the specific products giving rise to the claim or cause of action.
To the maximum extent permitted by applicable law, the company shall not be
liable to the customer or any third party for any general, direct, indirect, incidental,
special, consequential, or punitive damages, including, but not limited to, loss of
profits or anticipated profits, business interruption, loss of use, revenue, reputation
and data, costs incurred, loss or damage to property or equipment, bodily injury, or
death, arising from any claim or cause of action relating to the product, whether
such is based on warranty, contract, tort (including negligence and strict liability.
These limitations shall apply notwithstanding any failure of essential purpose of
any remedy. Some states and/or jurisdictions do not allow the exclusion or
limitation of incidental or consequential damages so the above exclusions may not
apply to certain customers.
The Customer assumes all other responsibility for any loss, damage, or injury to
persons or property arising out of, connected with, or resulting from the use of
Products, either alone or in combination with other products/components.
4. CLAIMS PROCEDURE:
The Customer shall make a claim by written notice to the Company through the
contact information listed on its website at www.fibaro.com or by contacting the
Company through the telephone number listed on the website. Any telephone
conversations will be recorded. The Company will issue a designated claim
number for each claim made. The Customer may be contacted by an authorized
warranty service representative to arrange a date for an inspection of the Product.
This inspection shall be in the presence of the Customer. The Product that is the
subject of the claim shall be made available by the Customer together with
complete standard equipment and the documents confirming the Product’s
purchase. Covered defects (as determined by the Company or its authorized
service representative) found during the limited warranty period shall be remedied
within thirty (30) days from the date of inspection or the date the Product is
delivered to the Company or its authorized service representative, whichever is
later. The limited warranty period shall be extended by the time that the Product is
in the possession of the authorized service representative or the Company.
Remember: before you submit a warranty claim, contact our technical support
using telephone or e-mail. More than 50% of operational problems is resolved
remotely, saving time and money spent to initiating claim procedure.
5. GOVERNING LAW AND BINDING ARBITRATION:
Please read this section carefully. It affects customers’ rights and will have a
substantial impact on how claims the company and the customer have against
each other are resolved. This limited warranty contains a binding arbitration
provision which may be enforced by the parties.
The Company and the Customer agree that any claim or dispute at law or equity
that has arisen or may arise between them relating in any way to or arising out of
this limited warranty or the Products will be resolved in accordance with the
provisions set forth in this Section.
A. Applicable Law. The Customer and the Company agree that, except to the
extent inconsistent with or preempted by federal law, the laws of the State of
Illinois, without regard to principles of conflict of laws, will govern the limited
warranty and Products and any claim or dispute that has arisen or may arise
between the Company and the Customer, except as otherwise stated herein. The
Federal Arbitration Act governs the interpretation and enforcement of this Section
5. The U.N. Convention on Contracts for the International Sales of Goods shall not
apply.
B. Agreement to Arbitrate. The Company and the Customer each agree that
any and all disputes or claims that have arisen or may arise between them relating
to or arising out of this limited warranty or the Products shall be resolved
exclusively through final and binding arbitration, rather than in a court proceeding.
Alternatively, the Customer may assert his/her claims in small claims court, if the
claims qualify and so long as the matter remains in such court and advances only
on an individual (non-class, non-representative) basis.
The Company and the Customer agree that each of them may bring claims against
the other only on an individual basis and not as a plaintiff or class member in any
purported class or representative action or proceeding. Unless both the Company
and the Customer agree, the arbitration may not consolidate or join more than one
person’s claims and many not otherwise preside over any form of a consolidated,
representative, or class proceeding.
C. Opt-Out. The Customer may opt-out of this agreement to arbitrate by sending
the Company a written opt-out notice, via certified mail and postmarked no later
than 30 days after the date of purchase of the Product. The opt-out notice must
include the Customer’s name and address, the serial number of the Product
purchased, and the date and location of the purchase. All other parts of this limited
warranty will still apply.
D. Procedures. The arbitration shall be administered by JAMS pursuant to its
Comprehensive Arbitration Rules and Procedures or pursuant to JAMS’
Streamlined Arbitration Rules and Procedures, whichever as applicable. JAMS’
rules are available at www.jamsadr.com. The use of the word “arbitrator” in this
provision shall not be construed to prohibit more than one arbitrator from presiding
over the arbitration; rather, the JAMS’ rules will govern the number of arbitrators
that may preside over an arbitration. The Customer will have a reasonable
opportunity to participate in the selection of the arbitrator.
A Customer who intends to seek arbitration must first make a written claim against
the Company pursuant to Section 4. If the Customer and the Company are unable
to resolve the claim within thirty (30) days from the date of the notice, the Company
or the Customer may initiate arbitration proceedings. A form for initiating arbitration
proceedings is available on JAMS’ website. In addition to filing the form with
JAMS, the party initiating the arbitration must mail a copy of the completed form to
the other party. In the event the Company initiates arbitration against a Customer,
it will send a copy of the completed form to the physical address the Company has
on file for the Customer.
The arbitration hearing shall be held in the county in which the Customer resides
or at another mutually agreed location.
Arbitration uses a neutral arbitrator instead of a judge or jury. Discovery or the
exchange of non-privileged information will be allowed pursuant to JAMS’ rules.
The arbitrator will decide the substance of all claims in accordance with applicable
law, including recognized principles of equity, and will honor all claims of privilege
recognized by law. An arbitrator can award the same damages and relief on an
individual basis that a court can award to an individual. The arbitrator’s award
shall be final and binding and judgment on the award rendered by the arbitrator
may be entered in any court having jurisdiction thereof. An award will consist of a
written statement stating the disposition of each claim, and will include a concise
written statement of the essential findings and conclusions on which the award is
based.
Payment of all filing, administration and arbitrator fees is governed by JAMS;
provided, however, that when a Customer initiates arbitration against the
Company, the fee required to be paid by the Customer is that amount designated
by JAMS for consumer arbitrations. All other costs will be paid by the Company.
If an arbitrator or court decides that any part of this limited warranty is invalid or
unenforceable, the other parts of the limited warranty shall still apply to the extent
applicable. In the event that this agreement to arbitrate is wholly inapplicable, the
Customers agree that any claim or dispute that has arisen or may arise between
the Customer and the Company must be resolved exclusively by a state or federal
court located in Cook County, Illinois. The Customer agrees to submit to the
personal jurisdiction of the courts located within Cook County, Illinois, for the
purpose of litigating all such claims or disputes.
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY
TO OPERATE THE EQUIPMENT.
US
Garantia - Ámérica do Sul
1. FIBAR GROUP S.A. (“Fabricante”) com sede social na ul. Lotnicza 1, 60-421
Poznań, inscrita no Registo Judicial Nacional da República de Polónia gerado por
Tribunal Distrital em Poznań Nowe Miasto e Wilda, XIII Divisão Comercial do
Registo Judicial Nacional sob número 553265, NIF 7811858097, REGON
301595664, capital social de 1 182 100 PLN pagado na sua totalidade, outros
dados de contato disponível sob: www.fibaro.com garante o Aparelho vendido
(„Aparelho”) está livre dos defeitos de material ou de produção).
2. O funcionamento defeituoso do Aparelho que não conformará com a
informação comunicada por Fabricante que seja resultado dos defeitos físicos do
Aparelho será considerado a responsabilidade de Fabricante no período de:
- 24 meses da data de compra pelo consumidor,
- 12 meses da data de compra pelo comerciante (consumidor e comerciante serão
em adelante junto denominados como „Cliente”.
3. Após deste período de garantia, Fabricante deve remover gratuitamente os
defeitos por meios de reparar ou substituir (após avaliação feita por Fabricante)
todas as peças defeituosas do Aparelho com peças novas ou revitalizadas.
Fabricante reserva o direito a substituir o Aparelho inteiro com um Aparelho novo
ou revitalizado. Fabricante não reembolsará o Cliente.
4. Nos casos particulares Fabricante pode substituir o Aparelho com um quais
parámetros técnicos serão semelhantes.
5. Apenas o proprietário do documento da garantia válido pode apresentar
reclamações.
6. Antes de apresentar uma reclamação, Fabricante recomenda contatar o Auxilio
ao Cliente, via telefono ou e-mail na página Web: https://www.fibaro.com/support.
7. Para apresentar uma reclamação Cliente deve contatar o Fabricante por e-mail
no endereço mencionado na página Web: https://www.fibaro.com/support.
8. Caso a reclamação será admitida, Cliente receberá o contacto para seu Centro
de Serviço Autorizado (CSA). Cliente deverá contactar o CSA e entrega-lhe o
Aparelho. Após receber o Aparelho o Fabricante enviará ao Cliente o número da
sua reclamação (RMA).
9. Os defeitos serão removidos dentro um prazo de 30 dias, contando da data de
entrega do Aparelho a CSA. O período da garantia será estendido por tempo no
qual o Aparelho se encontrará na disposição de CSA.
10. Cliente deverá entregar o Aparelho reclamado junto com todos os acessórios
estandartes e documentos comprovantes da sua compra.
11. Custes de transporte do produto reclamado no territorio da Polónia serão
cobrados pelo Fabricante. Caso o Aparelho será transportdo no estrangeiro,
custes de transporte do produto reclamado serão cobrados pelo Cliente. Caso a
reclamação seja injustificada, CSA tem direito a condenar o Cliente nas despesas
relacionadas com a resolução do pedido.
12. CSA recusará uma reclamação no caso de:
- uma utilização abusiva do Aparelho e contra as recomendações do manual,
- a entrega do Aparelho incompleto, sem acessórios, sem placa sinalética pelo
Cliente,
- a causa da falha do Aparelho seja não por defeito material ou da produção deste
Aparelho,
- o documento da garantia seja inválido e falta dos documentos da compra.
13. Fabricante não será responsável por nenhumas falhas ao património
causadas por Aparelho defeituoso. Fabricante não será responsável por
nenhumas perdas indiretas, particulares, consequentes ou morais, nem por
nenhumas perdas dos lucros, poupanças, dados, bens, reclamações das pessoas
terceiras.
Garantia de qualidade não se aplica a:
- danos estéticos (riscos, quebras, cortes, esfregos, deformações físicas que
sejam resultados de impacto, queda ou lançamento dum outro objeto em cima do
Aparelho ou sua utilização abusiva, não indicada no manual);
- danos que sejam resultado dum fator externo, p.ex.: inundacação, tempestade,
incêndio, raios, terremotos, guerras, conflitos sociais, força maior, occorências
imprevisíveis, roubo, inundação com um líquido, efusão de bateria, condições
meteorológicas; raios de sol, areia, humidade, baixa ou elevada temperatura,
polução do ar;
- danos que sejam resultado do funcionamento incorreto do software, um
ciberataque dum vírus, ou inconformidade com as atualizações do software
segundo as recomendações do fabricante;
- danos que sejam resultado das sobretensões nas redes energéticas e/ou de
telecomunicação, ou no caso da ligação incorreta do Aparelho à rede inconforme
com o manual, ou da ligação dos outros produtos que não são recomendados por
Fabricante;
- danos que sejam resultado do funcionamento do Aparelho ou seu armazém nas
condições drasticamente desfavoráveis, entendidos como: humidade
considerável, polinização, as temperaturas demasiado baixas (frio) ou altas.
Condições particulares do uso do Aparelho se encontram descritos no manual;
- danos que sejam resultado do uso dos acessórios não recomendados pelo
Fabricante;
- danos que sejam resultado das faltas na instalação elétrica do usuário, inclusive
fusíveis inadequados;
- danos que sejam resultado da falta de observação da correta conservação e uso
do Aparelho pelo Cliente, descritos no manual;
- danos que sejam resultado do uso das peças dos fabricantes terceiros, peças ou
acessórios impróprios para dado modelo, reparações ou alterações condutas
pelas pessoas não autorizadas;
- danos que sejam resultado do uso continuo do Aparelho ou acessórios
ineficazes.
14. Garantia não se aplica também às peças consumíveis do Aparelho ou outras
partes mencionadas no manual ou na documentação técnica que funcionam por
um prazo definido.
15. A presente garantia não anula, limita nem suspende nenhuns poderes de
Cliente que resultam do chamamento de garantia.
16. Fabricante não será responsável por nenhumas falhas ao património
causadas por Aparelho defeituoso. Fabricante não será responsável por
nenhumas perdas indiretas, particulares, consequentes ou morais, nem por
nenhumas perdas dos lucros, poupanças, dados, bens, reclamações das pessoas
terceiras ou outras perdas que serão o resultado ou serão ligados com o
funcionamento do Aparelho.
Garantía - América del Sur & Mexico
1. FIBAR GROUP SA con domicilio social en la calle Lotnicza 1, 60-421 Poznan,
inscrita en el Nacional Registro Judicial por el Juzgado de Distrito de
Poznań-Nowe Miasto y Wilda, Sala 8a de lo Económico del Nacional Registro
Judicial bajo el número: 553 265, CIF 7811858097, REGON [Número Estadístico]:
301595664, con el capital social de 1.182.100 PLN, totalmente desembolsado, los
demás datos de contacto están disponibles en la página web: www.fibaro.com (en
adelante "Fabricante") otorga la garantía para el dispositivo vendido ("Dispositi-
vo") y declara que está libre de defectos en material y mano de obra.
2. El Fabricante es responsable del funcionamiento defectuoso del Dispositivo
debido a los defectos físicos inherentes al Dispositivo que causen su
funcionamiento no conforme con las especificaciones del Fabricante en el periodo
de:
- 24 meses desde la fecha de compra por parte del consumidor,
- 12 meses desde la fecha de compra por parte del Cliente empresarial (consumidor
y Cliente empresarial en lo sucesivo se denominan conjuntamente el "Cliente").
3. El Fabricante se compromete a eliminar sin cargo adicional, los defectos
revelados durante la garantía mediante la reparación o el reemplazo (según el
Fabricante lo considera oportuno) de los componentes defectuosos del
Dispositivo por las piezas nuevas o reacondicionadas. El Fabricante se reserva el
derecho de sustituir todo el Dispositivo por uno nuevo o reacondicionado. El
Fabricante no reembolsa el dinero por el Dispositivo comprado.
4. En situaciones especiales, el Fabricante podrá sustituir el Dispositivo por otro
con los parámetros técnicos lo más similares posibles.
5. Sólo el titular de una garantía válida puede presentar una reclamación de
Garantía.
6. Antes de presentar la reclamación, el Fabricante recomienda contactarse con la
asistencia técnica por teléfono o por Internet cuyos datos están disponibles en la
página https://www.fibaro.com/support/.
7. Con el fin de presentar la reclamación, el Cliente debe ponerse en contacto con
el Fabricante a la dirección de correo electrónico indicada en la página
https://www.fibaro.com/support/.
8. Después de haber presentado adecuadamente la reclamación, el Cliente
recibirá los datos de contacto al Centro autorizado de servicio de garantía
("ASG"). El Cliente debe contactarse y entregar el Dispositivo a la ASG. Tras la
recepción del Dispositivo, el Fabricante informará al Cliente sobre el número de la
notificación (RMA).
9. Los defectos serán eliminados dentro de los 30 días, a contar desde la fecha de
entrega del Dispositivo al ASG. El periodo de garantía se extiende por el tiempo
en el que el Dispositivo esté a disposición del ASG.
10. El Dispositivo, objeto de la reclamación, debe estar puesto a disposición por el
Cliente con el equipamiento completo estándar y los documentos que confirman
su compra.
11. Los gastos de transporte del Dispositivo, objeto de la reclamación, en el
territorio de la República de Polonia serán cubiertos por el Fabricante. En el caso
de transporte de otros países, los gastos de transporte serán a cargo del Cliente.
En el caso de una reclamación injustificada, ASG tiene el derecho de cobrar al
Cliente los gastos asociados con la aclaración del caso.
12. ASG se niega a aceptar la reclamación en el caso:
- del uso del Dispositivo no conforme a su destino y al manual de uso,
- facilitar el Cliente, el Dispositivos incompleto, sin accesorios, sin placa de
identificación,
- determinar la causa del defecto que no sea defecto de material o de fabricación
inherente al Dispositivo,
- del documento de garantía inválido o falta de justificante de compra.
13. La Garantía de calidad no cubre:
- los daños mecánicos (grietas, fracturas, cortes, abrasiones, deformación física
debido a un golpe, caída o dejar caer otro objeto sobre el Dispositivo sobre el uso
no conforme a su destino determinado en el manual de uso);
- los daños ocasionados por causas externas, tales como: inundaciones,
tormentas, incendios, rayos, desastres naturales, terremotos, guerras, disturbios
civiles, fuerza mayor, accidentes imprevistos, robos, daños por líquidos, fugas de
la batería, condiciones climáticas; acción de rayos soles, arena, humedad, alta o
baja temperatura, contaminación atmosférica;
- el daño ocasionado por el software que funcione incorrectamente, debido al
ataque del virus informático, o no utilizar la actualización de software según lo
recomendado por el Fabricante;
- los daños ocasionados por: sobrecargas en la red eléctrica y/o de telecomunica-
ciones o conectarse a la red de una manera no conforme a las instrucciones de
uso o debido a la conexión de otros productos cuya conexión no está recomenda-
da por el Fabricante;
- los daño ocasionados por el trabajo o el almacenamiento del Dispositivo en
condiciones extremadamente adversas, es decir, alta humedad, polvo, temperatu-
ra baja (helada) o temperatura ambiente demasiado alta. Las condiciones
específicas en las que es admisible utilizar el Dispositivo están determinas en el
manual de uso;
- los daños causados por el uso de accesorios no recomendados por el
Fabricante;
- los daños causados por la instalación eléctrica defectuosa del usuario,
incluyendo el uso de fusibles incorrectos;
- los daños resultantes de ignorar el Cliente las acciones de mantenimiento y
servicio previstos en el manual de uso;
- los daños resultantes del uso de las piezas de repuesto y accesorios no-origina-
les, inadecuados para el modelo, la realización de reparaciones y modificaciones
por personas no autorizadas;
- los defectos causados por continuar el uso del Dispositivo o accesorios
defectuosos.
14. La garantía no cubre el desgaste normal de las piezas del Dispositivo y otras
piezas mencionadas en el manual de uso y la documentación técnica con un
tiempo de uso determinado.
15. La garantía del Dispositivo no excluye, no limita y no suspende los derechos
del Cliente resultantes de la garantía.
16. El Fabricante no se hace responsable de los daños ocasionados por el
Dispositivo defectuoso. El Fabricante no se hace responsable de los daños
indirectos, incidentales, especiales, consecuenciales o punitivos, o daños,
incluyendo entre otros el lucro cesante, ahorros, datos, pérdida de beneficios,
reclamaciones de terceros u otros daños derivados de o relacionados con el uso
de Dispositivo.
PROCEDIMIENTO PARA RECLAMO DE GARANTIA
El cliente deberá hacer una reclamación mediante notificación por escrito a la
compañía a través de la información de contacto que aparece en su sitio web
www.fibaro.com o poniéndose en contacto con la Compañía a través del número
de teléfono que aparece en la página web. Las conversaciones telefónicas podrán
ser grabadas. La Compañía emitirá un número de reclamo designado por cada
reclamación hecha. El cliente puede ser contactado por un representante de
servicio de garantía autorizado para concertar una fecha para una inspección del
producto. Esta inspección deberá estar en presencia del cliente. El producto
objeto de la reclamación se pondrá a disposición por conducto del cliente, junto
con el equipamiento correspondiente y los documentos que confirman la compra
del producto. Los defectos cubiertos (según lo determinado por la compañía o de
su representante autorizado) encontrados durante el periodo de garantía limitada
serán resueltas dentro de los treinta (30) días desde la fecha de la inspección, o
de la fecha en que el producto se entrega a la compañía o de su representante de
servicio autorizado, el que sea más tarde. El período de garantía limitada se
prolongará por el tiempo que el producto está en poder del representante de
servicio autorizado o la Compañía.
Warranty terms - Canada
1. FIBAR GROUP S.A. with its registered office in Poznań, ul. Lotnicza 1, 60-421
Poznań, entered into the Register of Entrepreneurs of the National Court Register
maintained by the District Court for Poznań-Nowe Miasto and Wilda in Poznań,
VIII Commercial Division of the National Court Register (KRS) under number:
553265, NIP 7811858097, REGON: 301595664, share capital PLN 1,182,100 paid
in full, other contact information is available at: www.fibaro.com (hereinafter "the
Manufacturer") guarantees that the device sold (hereinafter: "the Device" is free
from material and manufacturing defects.
2. The Manufacturer shall be responsible for malfunctioning of the Device resulting
from physical defects inherent in the Device that cause its operation to be
incompatible with the specifications within the period of:
- 24 months from the date of purchase by the consumer,
- 12 months from the date of purchase by a business customer (the consumer and
business customer are further collectively referred to as "Customer").
3. The Manufacturer shall remove any defects revealed during the guarantee
period, free of charge, by repairing or replacing (at the sole discretion of the
Manufacturer) the defective components of the Device with new or regenerated
components. The manufacturer reserves the right to replace the entire Device with
a new or regenerated device. The Manufacturer shall not refund money paid for
the device.
4. Under special circumstances, the Manufacturer may replace the Device with a
different device most similar in technical characteristics.
5. Only the holder of a valid guaranty document shall be entitled to make claims
under guarantee.
6. Before making a complaint, the Manufacturer recommends using the telephone
or online support available at https://www.fibaro.com/support/.
7. In order to make a complaint, the Customer should contact the Manufacturer via
the email address given at https://www.fibaro.com/support/.
8. After the complaint has been properly filed, the Customer will receive contact
details for the Authorized Guarantee Service ("AGS"). The customer should
contact and deliver the Device to AGS. Upon receipt of the Device, the manufactu-
rer shall inform the Customer of the return merchandise authorization number
(RMA).
9. Defects shall be removed within 30 days from the date of delivering the Device
to AGS. The guarantee period shall be extended by the time in which the Device
was kept by AGS.
10. The faulty device shall be provided by the Customer with complete standard
equipment and documents proving its purchase.
11. The cost of transporting the Device in the territory of the Republic of Poland
shall be covered by the Manufacturer. The costs of the Device transport from other
countries shall be covered by the Customer. For unjustified complaints, AGS may
CA
ES PT
Conditions de la garantie - Canada
1. FIBAR GROUP S.A. ayant son siège à Poznań ul. Lotnicza 1; 60-421 Poznań,
immatriculée au Registre des entrepreneurs du Registre Judiciaire National tenu
par Sąd Rejonowy [Tribunal de district] Poznań-Nowe Miasto i Wilda à Poznań,
VIII Département Économique au numéro : 553265, No TVA 7811858097,
REGON [SIRET] : 301595664, capital social de 1 182 100 PLN entièrement libéré,
d’autres coordonnées sont disponibles au site www.fibaro.com (ci-après le «
Fabricant ») garantit que l'appareil vendu (l’« Appareil ») est exempt de tout défaut
de matériaux et de fabrication.
2. Le fabricant est responsable du fonctionnement défectueux de l'Appareil en
raison de vices physiques de l’Appareil provoquant son fonctionnement non
conforme à la spécification du Fabricant pendant la période de :
- 24 mois à compter de la date d'achat par le consommateur,
- 12 mois à compter de la date d'achat par l’entreprise, (le consommateur et l’entreprise
sont ci-après dénommés collectivement le « Client »).
3. Le Fabricant s’engage à remédier gratuitement à tout défaut identifié au cours
de la période de garantie par la réparation ou le remplacement (à la discrétion du
Fabricant) des composants de l’Appareil défectueux par des pièces neuves ou
remises à neuf. Le Fabricant se réserve le droit de remplacer tout l'Appareil par un
autre, neuf ou remis à neuf. Fabricant ne rembourse pas le prix de l’Appareil
acheté.
4. Dans des situations particulières, le Fabricant peut remplacer l'Appareil par un
autre avec les paramètres techniques les plus similaires.
5. Seul le titulaire d'une garantie valide peut présenter des demandes de garantie.
6. Avant de faire une demande de garantie, le Fabricant vous recommande de
profiter de l’assistance technique par téléphone ou en ligne, accessible sur le site
https://www.fibaro.com/support/.
7. Pour présenter la demande d'activation de garantie, le Client doit s’adresser au
Fabricant par le courriel indiqué sur le site https://www.fibaro.com/support/.
8. Après la présentation de la demande d'activation de garantie valide, le Client
recevra des informations de contact pour le Service de garantie autorisé («SGA»).
Le client doit s’adresser au SGA et y fournir l’Appareil. Après avoir obtenu
l’Appareil, le Fabricant communiquera au Client le numéro d'application unique
(RMA).
9. Les vices seront éliminés dans un délai de 30 jours à compter de la date de
livraison de l’Appareil au SGA. La période de garantie est prolongée du temps
pendant lequel le dispositif restait à la disposition du SGA.
10. L’appareil étant l’objet d’une réclamation doit être mis à disposition par le
Client avec l’équipement standard complet et les documents confirmant son
achat.
11. Les frais de transport de l’Appareil étant l’objet d’une réclamation sur le
territoire polonais seront couverts par le Fabricant. Dans le cas du transport
d'autres pays, les frais de transport seront à la charge du Client. Dans le cas d'une
notification de la demande de réclamation injustifiée, le SGA a le droit de charger
le Client des frais concernant l'explication de la question.
12. SGA refuse d'accepter une réclamation en cas de :
- constatation de l’utilisation abusive et non conforme au mode d’emploi de
l’Appareil,
- mettre à disposition l’Appareil incomplet, sans accessoires, sans plaque
signalétique de la part du Client,
- déterminer la cause du défaut autre que le vice de matériau ou de production de
l’Appareil,
- du document de garantie non valable et l'absence de preuve d'achat.
13. La garantie de qualité ne couvre pas :
- des dommages mécaniques (fissures, fractures, coupures, écorchures,
déformation physique due à l'impact, la chute ou causée en laissant tomber sur
l'Appareil un autre objet ou par l’utilisation abusive de l’Appareil par rapport de
celle prévue dans le mode d’emploi);
- des dommages causés par des causes externes telles que: inondation, tempête,
feu, foudre, catastrophes naturelles, tremblements de terre, guerre, troubles civils,
cas de force majeure, accidents imprévus, vol, versement de liquide, fuite de la
batterie, conditions météorologiques; lumière du soleil, sable, humidité,
température élevée ou faible, pollution de l'air;
- des dommages causés par un logiciel défectueux en raison d'une attaque de
virus ou de ne pas mettre à jour du logiciel, l’opération recommandée par le
fabricant;
- des dommages résultant de : surtensions dans le réseau électrique et/ou de
télécommunication ou de se connecter au réseau énergétique d'une manière
incompatible avec les instructions ou à cause de la connexion d'autres produits
dont la connexion n’est pas recommandée par le fabricant;
- des dommages causés par le fonctionnement ou le stockage dans des
conditions extrêmement défavorables, soit humidité élevée, poussière,
température ambiante trop basse (gel) ou trop haute. Les conditions détaillées
dans lesquelles il est possible d'utiliser l'appareil détermine le mode d’emploi ;
- les dommages causés par l'utilisation d'accessoires non recommandés par le
Fabricant;
- des dommages causés par réseau électrique défectueux de l’utilisateur, y
compris l'utilisation de fusibles incorrects ;
- des dommages causés par négligence de maintenance et d'entretien prévus
dans le mode d’emploi de la part du Client ;
- des dommages résultant de l'utilisation des pièces de rechange et des
accessoires non originaux, incorrects pour le présent modèle, d’effectuer des
réparations et des modifications par des personnes non autorisées ;
- les défauts causés par la poursuite des travaux avec un Appareil ou un
équipement défectueux.
14. La garantie ne couvre pas l'usure normale des composants de l’Appareil et
d'autres dispositifs mentionnés dans le manuel d'utilisateur et la documentation
technique avec un temps spécifique de fonctionnement.
15. La garantie de l’Appareil n'exclut pas, ne limite ni suspend les droits du Client
découlant de la garantie légale.
16. Le Fabricant décline toute responsabilité en cas de dommages matériels
causés par un Appareil défectueux. Le Fabricant n'est pas responsable des
dommages indirects, accessoires, spéciaux, consécutifs ou le préjudice moral ni
des dommages, y compris mais sans s'y limiter les pertes de profits, d’économies,
de données, la perte des prestations, des sinistres par des tiers et d’autres
dommages découlant de ou liés à l'utilisation de l’Appareil.
17. Cette garantie peut-être transféré à un autre propriétaire.
18. La présente garantie est régie et doit être interprétée conformément aux lois
de la province de Québec et aux lois fédérales du Canada qui s'y appliquent.
FR
charge the Customer with costs related to the case.
12. AGS shall not accept a complaint claim when:
- the Device was misused or the manual was not observed,
- the Device was provided by the Customer incomplete, without accessories or
nameplate,
- it was determined that the fault was caused by other reasons than a material or
manufacturing defect of the Device
- the guarantee document is not valid or there is no proof of purchase,
13. The guarantee shall not cover:
- mechanical damages (cracks, fractures, cuts, abrasions, physical deformations
caused by impact, falling or dropping the device or other object, improper use or
not observing the operating manual);
- damages resulting from external causes, e.g.: flood, storm, fire, lightning, natural
disasters, earthquakes, war, civil disturbance, force majeure, unforeseen
accidents, theft, water damage, liquid leakage, battery spill, weather conditions,
sunlight, sand, moisture, high or low temperature, air pollution;
- damages caused by malfunctioning software, attack of a computer virus, or by
failure to update the software as recommended by the Manufacturer;
- damages resulting from: surges in the power and/or telecommunication network,
improper connection to the grid in a manner inconsistent with the operating
manual, or from connecting other devices not recommended by the Manufacturer.
S-v1.1
FCC ID:
2AA9MFGWPB121
IC number:
20430-FGWPB121
  • Page 1 1
  • Page 2 2

Fibaro FGWPB-111 | FGWPB-121 Short Manual

Tipo
Short Manual