Summer Waves P1000830A156 Guía de instalación

Categoría
Accesorios para piscinas elevadas
Tipo
Guía de instalación
DISTRIBUTED BY: Polygroup
®
Trading Limited
Unit 606, 6th Floor, Fairmont House, No.8 Cotton Tree Drive, Central, Hong Kong
Manual #
09C3A4USA009
OWNER’S MANUAL
SUMMER WAVES
®
CARTRIDGE FILTER PUMP
FOR ABOVE GROUND SWIMMING POOLS
RP350/RP400 Models
Should you encounter a problem with your Polygroup
®
Product, please DO NOT return the product to the place of purchase. All Warranty claims must be made directly
to Polygroup
®
. Prior to contacting Customer Service, please first review the Troubleshooting Guide in the Installation Manual, or review the FAQ and instructional
videos at support.polygroupstore.com. If you are still unable to correct the problem, please contact Polygroup
®
Customer Service at (888) 919-0070. Please have the
product type, model number and your purchase receipt ready, so that our Customer Service Representative can assist you in resolving the problem. You may be asked
to return all or part of the product for inspection and/or repair. Do not return any product to Polygroup
®
without a Return Merchandise Authorization number.
Polygroup
®
Trading Limited, (hereinafter “Polygroup
®
”) warrants to the original purchaser only, the RP type Electric Filter Pump against defects in material and
workmanship for 180 days from the date of purchase. Original Purchaser must retain proof of such purchase in the form of an original store sales receipt and must
produce such upon request by Polygroup
®
or its designated agents. Warranty claims cannot be processed without a valid proof of purchase.
This Limited Warranty applies only to the original purchaser of the product and is limited solely to the repair or replacement of the product, to be decided in Polygroup
®
’s
sole discretion. Consequential damages, including claims for loss of water, pool chemicals, damage, or labor are not covered under this Limited Warranty.
This Warranty will be declared invalid should the Purchaser modify or repair the product themselves or by unauthorized persons; use non-Polygroup
®
parts or accesso-
ries with the product; use the product in contravention of the manufacturer’s Instructions; use improper voltage; abuse the product in any way; or through accident or
negligence. Normal wear-and-tear is not covered under this Warranty, nor are acts of God outside the control of Polygroup
®
. Polygroup
®
will not be held responsible
for grasses that may grow through the ground cloth and/or pool liner, as this is not a manufacturing defect.
IN NO EVENT SHALL Polygroup
®
, THEIR AUTHORIZED AGENTS, RELATED ENTITIES, OR EMPLOYEES BE LIABLE TO THE BUYER OR ANY OTHER
PARTY FOR DIRECT OR CONSEQUENTIAL DAMAGES. Some states or countries, or other jurisdictions, do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
LIMITED WARRANTY
DO NOT RETURN PRODUCT TO STORE
For answers to common questions, setup videos and troubleshooting tips, please
visit support.polygroupstore.com or call Customer Service: (888) 919-0070
To order parts and accessories,
please visit www.polygroupstore.com
READ, AND KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
OWNER’S MANUAL
2
Should you encounter any problems, contact Customer Service at (888) 919-0070 from 8AM to 5PM MST, Monday-Friday.
Extended operating days and hours during peak season requirements.
TABLE OF CONTENTS
Warnings
Preliminary Steps, Important Notes, Pump Power Info and Parts List
Setup Instructions
Use of Pump, Motor Care and Filter Cartridge USE & CARE
Pool Maintenance & Pool Water Care
Troubleshooting Guide & Pool Pump Disassembly & Storage
Pump Removal and Rotor Inspection/Replacement
Replacement Parts Ordering Info
ASME Compliant Suction Fitting Info
3 ~ 6
7 ~ 9
10 ~ 11
12 ~ 13
13
14
15 ~ 16
17
18
OWNER’S MANUAL
3
Should you encounter any problems, contact Customer Service at (888) 919-0070 from 8AM to 5PM MST, Monday-Friday.
Extended operating days and hours during peak season requirements.
Safety Care for Children
1. Children, especially children younger than five years, are at high risk of drowning. Drowning occurs silently and quickly and can occur in as little as 2 in. (5 cm) of water.
2. Keep children in your direct sight, stay close, and actively supervise them when they are in or near this pool and when you are filling and emptying this pool.
3. When searching for a missing child, check the pool first, even if the child is thought to be in the house.
4. Locate pumps and filters in such a way that children cannot climb on them and gain access to the pool.
5. WARNING: To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times.
Swimming Pool Barriers
Very Important: Swimming pool barriers, which restrict access to the pool by small children, may be required by law. A barrier is necessary to provide protection against
potential drowning and near drowning. Barriers are not a substitute for constant supervision of children. Check state or local laws and codes before setting up pool.
Swimming Pool Equipment
1. The use of artificial pool lighting is at the discretion of the pool owner. Lighting, when installed, should be in accordance with Article 680 of the
National Electrical Code (NEC) or its latest approved edition and in consultation with a licensed electrical professional.
2. Keep all electrical lines, radios, speakers, and other electrical appliances away from the pool.
3. Do not place pool near or under overhead electrical lines.
4. All electrical components installed in and/or adjacent to an aboveground/onground residential swimming pool shall be installed in accordance with and shall comply
with the requirements of the latest published edition of NFPA 70, National Electrical Code (NEC
®
) Article 680, Swimming pools, fountains, and similar installations,
and any state or local code.
Filter Pump Awareness
1. WARNING: Risk of Electric Shock. Connect only to a grounding type receptacle. This product is provided with a ground-fault circuit-interrupter. If replacement of
the plug or cord is needed, use only identical replacement parts.
2. WARNING: To reduce the risk of electric shock, replace damaged cord immediately.
3. WARNING: To reduce the risk of electric shock, do not use extension cord to connect unit to electric supply; provide a properly located outlet.
4. CAUTION: To reduce the risk of electric shock, the pool must be installed no closer than 6 feet (1.8m) from any electrical outlet. Do not place portable appliances
closer than 5 feet (1.5m) from the pool.
5. CAUTION: This pump is for use with storable pools only. Do not use with permanently-installed pools. A storable pool is constructed so that it is capable of being
readily disassembled for storage and reassembled to its original integrity. A permanently-installed pool is constructed in or on the ground or in a building such that it
cannot be readily disassembled for storage.
6. CAUTION: For continued protection against possible electric shock, this unit is to be mounted to the base in accordance with the installation instructions.
7. Do not bury cord. Locate cord to minimize abuse from lawn mowers, hedge trimmers, and other equipment.
8. The unit is provided with a ground-fault circuit-interrupter (GFCI). To test the GFCI, push the test button. The GFCI should interrupt power. Push the reset button.
Power should be restored. If the GFCI fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the pump without the test button being
pushed, a ground current is flowing, indicating the possibility of an electric shock. Do not use this pump. Disconnect the pump, and have the problem corrected by
a qualified service representative before using.
9. The Filter Pump is to be assembled by an adult; care should be taken in the unpacking and assembling of the Filter Pump. This pool may contain accessible
potentially hazardous sharp edges or sharp points that are a necessary part of the function of the Filter Pump.
10. If a drain or suction outlet cover is missing or broken, do not use the pool. Suction can cause body part entrapment, hair and jewelry entanglement, evisceration,
or drowning. Repair or replace the drain or suction outlet cover before allowing the pool to be used. During nighttime pool use, artificial lighting shall be used to
illuminate all safety signs, ladders, steps, deck surfaces, and walks.
11. The floor of the pool shall be visible at all times from the outside perimeter of the pool.
12. Post a list of emergency telephone numbers such as the nearest available police, fire, ambulance, and/or rescue unit. These numbers are to be kept near the
telephone, which is closest to the pool.
13. Basic lifesaving equipment, including one of the following should be on hand at all times:
A light, strong, rigid pole (shepherd's crook) not less than twelve feet (12’) [366cm] long.
A minimum one-fourth inch (¼”) [6.35 mm] diameter rope as long as one and one half (1 ½) times the maximum width of the pool or fifty feet (50’) [15.24 meters],
whichever is less, which has been firmly attached to a Coast Guard-approved ring buoy having an outside diameter of approximately fifteen inches (15”) [38.1 cm],
or similarly approved flotation device.
14. Pool shall be located at a minimum distance of 6ft (1.83m) from any receptacle, and all 125-volt 15- and 20-ampere receptacles located within 20ft (6.0m) of the
pool shall be protected by a ground fault circuit interrupter (GFCI), where distances are by measuring the shortest path the supply cord of an appliance connected
to the receptacle would follow, without piercing a floor, wall, ceiling, doorway with hinged or sliding door, window opening, or other effective permanent barrier, to
the inside pool wall.
Circulation Systems
1. Installers shall follow written instructions regarding positioning of all equipment connected to the circulation systems.
2. The installer shall follow written instructions provided for operating the circulation system components.
3. All circulation system components and pump that require replacement or servicing shall be installed according to the pump’s instruction manual.
4. Circulation equipment shall be installed per manufacturer’s instructions to provide proper mounting and support, to prevent damage from misalignment, settlement,
and vibration, and to minimize the potential for the accumulation of debris and moisture. Please refer to pump’s instruction manual.
Chemicals
For safety sake, ensure the deepest part of the pool is always visible. The user must properly maintain the clarity of the pool water at all times. Check the pH and chlorine
levels periodically and make sure they are within the recommended limits. Additional water treatment chemicals might be needed from time to time. Have the water sample
tested by a local pool supply store to determine if additional chemical is needed. Turn on the pump for the recommended hours daily. If you are unsure of the time frames
please refer to support.polygroupstore.com for the recommended Pump Operation Hours based on pool types and sizes. Clean and replace filter cartridge frequently.
Replace only with genuine Polygroup
®
/ Summer Waves
®
Brand filter cartridge. Refer to the Filter Pump manual for additional water care information.
Entrapment Risk
1. Entrapment Avoidance: There shall be no protrusions or other obstruction in the swimming area, which may cause entrapment or entanglement of the user. If
a suction outlet cover is missing or broken, do not use the pool. Suction can cause body part entrapment, hair and jewelry entanglement, evisceration, or drowning.
Repair or replace the suction outlet cover before allowing the pool to be used.
2. DANGER! TO AVOID SERIOUS INJURY OR DEATH, CLOSE THE POOL OR SPA TO BATHERS IF ANY SUCTION OUTLET COVER/GRATE IS MISSING,
BROKEN, OR INOPERATIVE.
3. Never play or swim near drains or suction fittings. Your body or hair may be trapped causing permanent injury or drowning.
4. Never enter the pool or spa if a suction fitting or drain cover is loose, broken, or missing.
5. Immediately notify the pool/spa owner or operator if you find a drain cover loose, broken, or missing.
Drowning Risk
1. Keep unsupervised children from accessing the pool by installing fencing or other approved barriers around all sides of pool. State or local laws or codes may require
fencing or other approved barriers. Check state or local laws and codes before setting up pool.
2. Toys, chairs, tables, or similar objects that a young child could climb shall be at least four feet (4’) [121.92 cm] from the pool. The pump filter system shall be positioned
so as to prevent it being used as a means of access to the pool by young children. Do not leave toys inside pool when finished using, since toys and similar items
might attract a child to the pool.
3. Position furniture (for example: tables, chairs) away from pool and so that children cannot climb on it to gain access to the pool.
Electrocution Risk
1. Keep all electrical lines, radios, speakers, and other electrical appliances away from the pool.
2. Do not place pool near or under overhead electrical lines.
First Aid
1. Keep a working phone and a list of emergency numbers near the pool.
2. Become certified in cardiopulmonary resuscitation (CPR). In the event of an emergency, immediate use of CPR can make a lifesaving difference.
Special Warning
1. Local building codes may require obtaining a building or electrical permit. Installer shall follow regulations on setback, barriers, devices, and other conditions.
2. Safety signs shall comply with requirements of ANSI-Z535 and use signal wording.
3. DO NOT attempt to assemble this pool in adverse weather conditions, windy conditions, or when the temperature is below 60°F.
4. This is a storable filter pump, which should be disassembled and stored when temperatures are expected to fall below 32°F.
Extra Safety Warning
1. Adult supervision is always required.
2. Parents should learn CPR.
3. Keep all electrical radios, speakers, and other appliances away from the swimming pool.
4. When you touch the filter, pump, or electrical parts, be sure the ground under your feet is “Bone Dry.”
5. All electrical outlets should have a GFCI, and connections should be a minimum of 6 feet (1.83 m) from the outside perimeter of the wall of the pool.
From 6–10 feet (1.83–3.05 m), there should be either a fixed connection (outlet box) or twistlock connection with a GFCI.
6. Connect power cords to a 3-wire grounding-type outlet only.
7. Keep all breakable objects out of the pool area.
8. Alcohol consumption and pool activities do not mix. Never allow anyone to swim, dive, or slide under the influence of alcohol or drugs.
9. Severe electrical shock could result if you install your pump or filter on a deck. The pump or filter could fall into the water, causing severe shock or electrocution.
10. Do not install on a deck or other surface at, above, or slightly below the top rail of the pool.
11. Do not use the filter pump during severe weather conditions, i.e. electrical storms, tornadoes, etc.
12. Be aware of overhead power lines when vacuuming your pool or using a telescoping pole.
13. Check regularly for signs of wear or loose bolts that could make the deck unsafe.
14. Please contact pool site dealer or manufacturer for additional safety signs if deemed necessary.
15. For pool service, select a certified pool professional. For additional safety information, see www.APSP.org
Consumer Awareness Booklets and Information Source
Contact: U.S. Consumer Product Safety Commission at www.cpsc.gov/safety-education/safety-guides/pools-and-spas, Pub. #362 “Safety Barrier Guidelines for Home Pools.”
1. The Sensible Way to Enjoy Your Aboveground/Onground Swimming Pool.
2. Children Aren’t Waterproof.
3. Layers of Protection.
4. Pool and Spa Emergency Procedures for Infants and Children.
5. Be Safety Aware Copies of the above brochures are available free from the APSP. Go to: www.APSP.org
Safety Education Programs and Materials
Educational programs and materials (i.e., seminars, workshops, brochures, videos, instructional guides) are available from the APSP, other aquatic safety groups, and
by private firms. As a means of communicating useful safety information to pool owners/operators, and users, industry members are permitted to provide such
information to owners/operators and to request or require owners/operators to sign a statement that they have received, read, and will follow the guidelines.
Other sources of safety information:
• www.cdc.gov
• www.cpsc.gov
• www.drowningpreventionalliance.com
• www.nspf.org
• www.safekids.org
ANSI American National Standards Institute
25 West 43rd Street, New York NY 10036
Contact: 212-642-4900
www.ansi.org
APSP Association of Pool & Spa Professionals
(formerly National Spa and Pool Institute)
2111 Eisenhower Avenue, Suite 500
Alexandria VA 22314-4679
Contact: 703-838-0083
www.apsp.org
ASME American Society of Mechanical Engineers
Two Park Avenue, New York NY 10016-5990
Contact: 800-843-2763 (U.S. & Canada) 973-882-1170 (outside North America)
www.asme.org
NSPI National Spa and Pool Institute (see APSP)
UL Underwriters Laboratories
333 Pfingsten Road,Northbrook IL 60062-2096
Contact: 877-854-3577 or 847-272-8800
www.ul.com
NSF NSF International
P.O. Box 130140
789 N. Dixboro Road
Ann Arbor MI 48105
Contact: 800-673-6275 or 734-769-8010
www.nsf.org
ASTM ASTM International (formerly American Society of Testing & Materials)
100 Barr Harbor Drive, P.O. BOX C700
West Conshohocken, PA 19428-2959
Contact: 877-909-2786 (USA & Canada) or 610-832-9585 (International)
www.astm.org
NEC National Electrical Code (see NFPA)
NFPA National Fire Protection Association
1 Batterymarch Park, Quincy MA 02169-7471
Contact: 800-344-3555 (U.S. & Canada) or 617-770-3000 (International)
www.nfpa.org
Filtration Systems
Any equipment connected to the circulation systems shall be positioned so as to prevent their being used as a means of access to the pool by young children. (See the
latest published edition of ANSI/ APSP-8 Model Barrier Code for Residential Swimming Pools, Spas, and Hot Tubs.)
Barrier
Barriers are necessary to provide protection against potential drowning and near drowning, and barriers are not a substitute for the constant supervision of children.
(See latest published edition of ANSI/APSP-8 Model Barrier Code for Residential Swimming Pools, Spas, and Hot Tubs.)
Risk of Drowning, Entrapment, and Diving Accidents
Publications are available that describe the risk of drowning, entrapment, and diving accidents. Available publications related to pool safety include the Association
of Pool and Spa Professionals’ (APSP) booklets entitled: The Sensible Way to Enjoy Your Aboveground/ Onground Swimming Pool, Children Aren’t Waterproof, Pool
and Spa Emergency Procedures for Infants and Children, Layers of Protection, and the latest published edition of ANSI/APSP-8 Model Barrier Code for
Residential Swimming Pools, Spas, and Hot Tubs.
Installer Responsibilities
All of these components shall be positioned so as to prevent their being used as a means of access to the pool by young children.
(See Barrier Code for Residential Swimming Pools, Spas, and Hot Tubs.)
IMPORTANT SAFETY INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions should always be followed, including the following:
READ AND FOLLOW ALL INSTRUCTIONS
Keep for Future Reference. Failure to follow these warnings and instructions can result in serious injury or death to users, especially children.
NOTICE: CUSTOMERS THAT PURCHASE POOLS MAY BE REQUIRED BY LOCAL OR STATE LAW TO INCUR ADDITIONAL EXPENSES WHEN INSTALLING A POOL, IN
ORDER TO COMPLY WITH STATE OR LOCAL LAWS REGARDING FENCING AND OTHER SAFETY REQUIREMENTS. CUSTOMERS SHOULD CONTACT THEIR LOCAL
BUILDING CODE ENFORCEMENT OFFICE FOR FURTHER DETAILS. POLYGROUP
®
IS NOT RESPONSIBLE FOR ANY ADDITIONAL EXPENSES THAT YOU MAY INCUR.
WARNING
DO NOT SIT ON
OR LAY OVER
POOL WALL
YOU CAN BE PERMANENTLY
INJURED.
WARNING
AVOID ENTRAPMENT!
STAY AWAY FROM DRAINS & SUCTION
FITTINGS. YOUR HAIR, BODY & JEWELRY
CAN GET SUCKED INTO DRAIN. YOU COULD
BE HELD UNDER WATER & DROWN. DO NOT
USE POOL IF DRAIN OR SUCTION OUTLET
COVER IS MISSING OR BROKEN.
DANGER
PREVENT DROWNING!
CLOSELY WATCH CHILDREN WHO
ARE IN OR NEAR THIS POOL. CHILDREN
UNDER 5 ARE AT HIGHEST RISK FOR
DROWNING. EMPTY POOL OR PREVENT
ACCESS WHEN NOT IN USE.
NO DIVING!
SHALLOW WATER
YOU CAN BREAK
YOUR NECK AND BE
PARALYZED.
4
Should you encounter any problems, contact Customer Service at (888) 919-0070 from 8AM to 5PM MST, Monday-Friday.
Extended operating days and hours during peak season requirements.
Safety Care for Children
1. Children, especially children younger than five years, are at high risk of drowning. Drowning occurs silently and quickly and can occur in as little as 2 in. (5 cm) of water.
2. Keep children in your direct sight, stay close, and actively supervise them when they are in or near this pool and when you are filling and emptying this pool.
3. When searching for a missing child, check the pool first, even if the child is thought to be in the house.
4. Locate pumps and filters in such a way that children cannot climb on them and gain access to the pool.
5. WARNING: To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times.
Swimming Pool Barriers
Very Important: Swimming pool barriers, which restrict access to the pool by small children, may be required by law. A barrier is necessary to provide protection against
potential drowning and near drowning. Barriers are not a substitute for constant supervision of children. Check state or local laws and codes before setting up pool.
Swimming Pool Equipment
1. The use of artificial pool lighting is at the discretion of the pool owner. Lighting, when installed, should be in accordance with Article 680 of the
National Electrical Code (NEC) or its latest approved edition and in consultation with a licensed electrical professional.
2. Keep all electrical lines, radios, speakers, and other electrical appliances away from the pool.
3. Do not place pool near or under overhead electrical lines.
4. All electrical components installed in and/or adjacent to an aboveground/onground residential swimming pool shall be installed in accordance with and shall comply
with the requirements of the latest published edition of NFPA 70, National Electrical Code (NEC
®
) Article 680, Swimming pools, fountains, and similar installations,
and any state or local code.
Filter Pump Awareness
1. WARNING: Risk of Electric Shock. Connect only to a grounding type receptacle. This product is provided with a ground-fault circuit-interrupter. If replacement of
the plug or cord is needed, use only identical replacement parts.
2. WARNING: To reduce the risk of electric shock, replace damaged cord immediately.
3. WARNING: To reduce the risk of electric shock, do not use extension cord to connect unit to electric supply; provide a properly located outlet.
4. CAUTION: To reduce the risk of electric shock, the pool must be installed no closer than 6 feet (1.8m) from any electrical outlet. Do not place portable appliances
closer than 5 feet (1.5m) from the pool.
5. CAUTION: This pump is for use with storable pools only. Do not use with permanently-installed pools. A storable pool is constructed so that it is capable of being
readily disassembled for storage and reassembled to its original integrity. A permanently-installed pool is constructed in or on the ground or in a building such that it
cannot be readily disassembled for storage.
6. CAUTION: For continued protection against possible electric shock, this unit is to be mounted to the base in accordance with the installation instructions.
7. Do not bury cord. Locate cord to minimize abuse from lawn mowers, hedge trimmers, and other equipment.
8. The unit is provided with a ground-fault circuit-interrupter (GFCI). To test the GFCI, push the test button. The GFCI should interrupt power. Push the reset button.
Power should be restored. If the GFCI fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the pump without the test button being
pushed, a ground current is flowing, indicating the possibility of an electric shock. Do not use this pump. Disconnect the pump, and have the problem corrected by
a qualified service representative before using.
9. The Filter Pump is to be assembled by an adult; care should be taken in the unpacking and assembling of the Filter Pump. This pool may contain accessible
potentially hazardous sharp edges or sharp points that are a necessary part of the function of the Filter Pump.
10. If a drain or suction outlet cover is missing or broken, do not use the pool. Suction can cause body part entrapment, hair and jewelry entanglement, evisceration,
or drowning. Repair or replace the drain or suction outlet cover before allowing the pool to be used. During nighttime pool use, artificial lighting shall be used to
illuminate all safety signs, ladders, steps, deck surfaces, and walks.
11. The floor of the pool shall be visible at all times from the outside perimeter of the pool.
12. Post a list of emergency telephone numbers such as the nearest available police, fire, ambulance, and/or rescue unit. These numbers are to be kept near the
telephone, which is closest to the pool.
13. Basic lifesaving equipment, including one of the following should be on hand at all times:
A light, strong, rigid pole (shepherd's crook) not less than twelve feet (12’) [366cm] long.
A minimum one-fourth inch (¼”) [6.35 mm] diameter rope as long as one and one half (1 ½) times the maximum width of the pool or fifty feet (50’) [15.24 meters],
whichever is less, which has been firmly attached to a Coast Guard-approved ring buoy having an outside diameter of approximately fifteen inches (15”) [38.1 cm],
or similarly approved flotation device.
14. Pool shall be located at a minimum distance of 6ft (1.83m) from any receptacle, and all 125-volt 15- and 20-ampere receptacles located within 20ft (6.0m) of the
pool shall be protected by a ground fault circuit interrupter (GFCI), where distances are by measuring the shortest path the supply cord of an appliance connected
to the receptacle would follow, without piercing a floor, wall, ceiling, doorway with hinged or sliding door, window opening, or other effective permanent barrier, to
the inside pool wall.
Circulation Systems
1. Installers shall follow written instructions regarding positioning of all equipment connected to the circulation systems.
2. The installer shall follow written instructions provided for operating the circulation system components.
3. All circulation system components and pump that require replacement or servicing shall be installed according to the pump’s instruction manual.
4. Circulation equipment shall be installed per manufacturer’s instructions to provide proper mounting and support, to prevent damage from misalignment, settlement,
and vibration, and to minimize the potential for the accumulation of debris and moisture. Please refer to pump’s instruction manual.
Chemicals
For safety sake, ensure the deepest part of the pool is always visible. The user must properly maintain the clarity of the pool water at all times. Check the pH and chlorine
levels periodically and make sure they are within the recommended limits. Additional water treatment chemicals might be needed from time to time. Have the water sample
tested by a local pool supply store to determine if additional chemical is needed. Turn on the pump for the recommended hours daily. If you are unsure of the time frames
please refer to support.polygroupstore.com for the recommended Pump Operation Hours based on pool types and sizes. Clean and replace filter cartridge frequently.
Replace only with genuine Polygroup
®
/ Summer Waves
®
Brand filter cartridge. Refer to the Filter Pump manual for additional water care information.
Entrapment Risk
1. Entrapment Avoidance: There shall be no protrusions or other obstruction in the swimming area, which may cause entrapment or entanglement of the user. If
a suction outlet cover is missing or broken, do not use the pool. Suction can cause body part entrapment, hair and jewelry entanglement, evisceration, or drowning.
Repair or replace the suction outlet cover before allowing the pool to be used.
2. DANGER! TO AVOID SERIOUS INJURY OR DEATH, CLOSE THE POOL OR SPA TO BATHERS IF ANY SUCTION OUTLET COVER/GRATE IS MISSING,
BROKEN, OR INOPERATIVE.
3. Never play or swim near drains or suction fittings. Your body or hair may be trapped causing permanent injury or drowning.
4. Never enter the pool or spa if a suction fitting or drain cover is loose, broken, or missing.
5. Immediately notify the pool/spa owner or operator if you find a drain cover loose, broken, or missing.
Drowning Risk
1. Keep unsupervised children from accessing the pool by installing fencing or other approved barriers around all sides of pool. State or local laws or codes may require
fencing or other approved barriers. Check state or local laws and codes before setting up pool.
2. Toys, chairs, tables, or similar objects that a young child could climb shall be at least four feet (4’) [121.92 cm] from the pool. The pump filter system shall be positioned
so as to prevent it being used as a means of access to the pool by young children. Do not leave toys inside pool when finished using, since toys and similar items
might attract a child to the pool.
3. Position furniture (for example: tables, chairs) away from pool and so that children cannot climb on it to gain access to the pool.
Electrocution Risk
1. Keep all electrical lines, radios, speakers, and other electrical appliances away from the pool.
2. Do not place pool near or under overhead electrical lines.
First Aid
1. Keep a working phone and a list of emergency numbers near the pool.
2. Become certified in cardiopulmonary resuscitation (CPR). In the event of an emergency, immediate use of CPR can make a lifesaving difference.
Special Warning
1. Local building codes may require obtaining a building or electrical permit. Installer shall follow regulations on setback, barriers, devices, and other conditions.
2. Safety signs shall comply with requirements of ANSI-Z535 and use signal wording.
3. DO NOT attempt to assemble this pool in adverse weather conditions, windy conditions, or when the temperature is below 60°F.
4. This is a storable filter pump, which should be disassembled and stored when temperatures are expected to fall below 32°F.
Extra Safety Warning
1. Adult supervision is always required.
2. Parents should learn CPR.
3. Keep all electrical radios, speakers, and other appliances away from the swimming pool.
4. When you touch the filter, pump, or electrical parts, be sure the ground under your feet is “Bone Dry.”
5. All electrical outlets should have a GFCI, and connections should be a minimum of 6 feet (1.83 m) from the outside perimeter of the wall of the pool.
From 6–10 feet (1.83–3.05 m), there should be either a fixed connection (outlet box) or twistlock connection with a GFCI.
6. Connect power cords to a 3-wire grounding-type outlet only.
7. Keep all breakable objects out of the pool area.
8. Alcohol consumption and pool activities do not mix. Never allow anyone to swim, dive, or slide under the influence of alcohol or drugs.
9. Severe electrical shock could result if you install your pump or filter on a deck. The pump or filter could fall into the water, causing severe shock or electrocution.
10. Do not install on a deck or other surface at, above, or slightly below the top rail of the pool.
11. Do not use the filter pump during severe weather conditions, i.e. electrical storms, tornadoes, etc.
12. Be aware of overhead power lines when vacuuming your pool or using a telescoping pole.
13. Check regularly for signs of wear or loose bolts that could make the deck unsafe.
14. Please contact pool site dealer or manufacturer for additional safety signs if deemed necessary.
15. For pool service, select a certified pool professional. For additional safety information, see www.APSP.org
Consumer Awareness Booklets and Information Source
Contact: U.S. Consumer Product Safety Commission at www.cpsc.gov/safety-education/safety-guides/pools-and-spas, Pub. #362 “Safety Barrier Guidelines for Home Pools.”
1. The Sensible Way to Enjoy Your Aboveground/Onground Swimming Pool.
2. Children Aren’t Waterproof.
3. Layers of Protection.
4. Pool and Spa Emergency Procedures for Infants and Children.
5. Be Safety Aware Copies of the above brochures are available free from the APSP. Go to: www.APSP.org
Safety Education Programs and Materials
Educational programs and materials (i.e., seminars, workshops, brochures, videos, instructional guides) are available from the APSP, other aquatic safety groups, and
by private firms. As a means of communicating useful safety information to pool owners/operators, and users, industry members are permitted to provide such
information to owners/operators and to request or require owners/operators to sign a statement that they have received, read, and will follow the guidelines.
Other sources of safety information:
• www.cdc.gov
• www.cpsc.gov
• www.drowningpreventionalliance.com
• www.nspf.org
• www.safekids.org
ANSI American National Standards Institute
25 West 43rd Street, New York NY 10036
Contact: 212-642-4900
www.ansi.org
APSP Association of Pool & Spa Professionals
(formerly National Spa and Pool Institute)
2111 Eisenhower Avenue, Suite 500
Alexandria VA 22314-4679
Contact: 703-838-0083
www.apsp.org
ASME American Society of Mechanical Engineers
Two Park Avenue, New York NY 10016-5990
Contact: 800-843-2763 (U.S. & Canada) 973-882-1170 (outside North America)
www.asme.org
NSPI National Spa and Pool Institute (see APSP)
UL Underwriters Laboratories
333 Pfingsten Road,Northbrook IL 60062-2096
Contact: 877-854-3577 or 847-272-8800
www.ul.com
NSF NSF International
P.O. Box 130140
789 N. Dixboro Road
Ann Arbor MI 48105
Contact: 800-673-6275 or 734-769-8010
www.nsf.org
ASTM ASTM International (formerly American Society of Testing & Materials)
100 Barr Harbor Drive, P.O. BOX C700
West Conshohocken, PA 19428-2959
Contact: 877-909-2786 (USA & Canada) or 610-832-9585 (International)
www.astm.org
NEC National Electrical Code (see NFPA)
NFPA National Fire Protection Association
1 Batterymarch Park, Quincy MA 02169-7471
Contact: 800-344-3555 (U.S. & Canada) or 617-770-3000 (International)
www.nfpa.org
Filtration Systems
Any equipment connected to the circulation systems shall be positioned so as to prevent their being used as a means of access to the pool by young children. (See the
latest published edition of ANSI/ APSP-8 Model Barrier Code for Residential Swimming Pools, Spas, and Hot Tubs.)
Barrier
Barriers are necessary to provide protection against potential drowning and near drowning, and barriers are not a substitute for the constant supervision of children.
(See latest published edition of ANSI/APSP-8 Model Barrier Code for Residential Swimming Pools, Spas, and Hot Tubs.)
Risk of Drowning, Entrapment, and Diving Accidents
Publications are available that describe the risk of drowning, entrapment, and diving accidents. Available publications related to pool safety include the Association
of Pool and Spa Professionals’ (APSP) booklets entitled: The Sensible Way to Enjoy Your Aboveground/ Onground Swimming Pool, Children Aren’t Waterproof, Pool
and Spa Emergency Procedures for Infants and Children, Layers of Protection, and the latest published edition of ANSI/APSP-8 Model Barrier Code for
Residential Swimming Pools, Spas, and Hot Tubs.
Installer Responsibilities
All of these components shall be positioned so as to prevent their being used as a means of access to the pool by young children.
(See Barrier Code for Residential Swimming Pools, Spas, and Hot Tubs.)
5
OWNER’S MANUAL
Should you encounter any problems, contact Customer Service at (888) 919-0070 from 8AM to 5PM MST, Monday-Friday.
Extended operating days and hours during peak season requirements.
Safety Care for Children
1. Children, especially children younger than five years, are at high risk of drowning. Drowning occurs silently and quickly and can occur in as little as 2 in. (5 cm) of water.
2. Keep children in your direct sight, stay close, and actively supervise them when they are in or near this pool and when you are filling and emptying this pool.
3. When searching for a missing child, check the pool first, even if the child is thought to be in the house.
4. Locate pumps and filters in such a way that children cannot climb on them and gain access to the pool.
5. WARNING: To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times.
Swimming Pool Barriers
Very Important: Swimming pool barriers, which restrict access to the pool by small children, may be required by law. A barrier is necessary to provide protection against
potential drowning and near drowning. Barriers are not a substitute for constant supervision of children. Check state or local laws and codes before setting up pool.
Swimming Pool Equipment
1. The use of artificial pool lighting is at the discretion of the pool owner. Lighting, when installed, should be in accordance with Article 680 of the
National Electrical Code (NEC) or its latest approved edition and in consultation with a licensed electrical professional.
2. Keep all electrical lines, radios, speakers, and other electrical appliances away from the pool.
3. Do not place pool near or under overhead electrical lines.
4. All electrical components installed in and/or adjacent to an aboveground/onground residential swimming pool shall be installed in accordance with and shall comply
with the requirements of the latest published edition of NFPA 70, National Electrical Code (NEC
®
) Article 680, Swimming pools, fountains, and similar installations,
and any state or local code.
Filter Pump Awareness
1. WARNING: Risk of Electric Shock. Connect only to a grounding type receptacle. This product is provided with a ground-fault circuit-interrupter. If replacement of
the plug or cord is needed, use only identical replacement parts.
2. WARNING: To reduce the risk of electric shock, replace damaged cord immediately.
3. WARNING: To reduce the risk of electric shock, do not use extension cord to connect unit to electric supply; provide a properly located outlet.
4. CAUTION: To reduce the risk of electric shock, the pool must be installed no closer than 6 feet (1.8m) from any electrical outlet. Do not place portable appliances
closer than 5 feet (1.5m) from the pool.
5. CAUTION: This pump is for use with storable pools only. Do not use with permanently-installed pools. A storable pool is constructed so that it is capable of being
readily disassembled for storage and reassembled to its original integrity. A permanently-installed pool is constructed in or on the ground or in a building such that it
cannot be readily disassembled for storage.
6. CAUTION: For continued protection against possible electric shock, this unit is to be mounted to the base in accordance with the installation instructions.
7. Do not bury cord. Locate cord to minimize abuse from lawn mowers, hedge trimmers, and other equipment.
8. The unit is provided with a ground-fault circuit-interrupter (GFCI). To test the GFCI, push the test button. The GFCI should interrupt power. Push the reset button.
Power should be restored. If the GFCI fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the pump without the test button being
pushed, a ground current is flowing, indicating the possibility of an electric shock. Do not use this pump. Disconnect the pump, and have the problem corrected by
a qualified service representative before using.
9. The Filter Pump is to be assembled by an adult; care should be taken in the unpacking and assembling of the Filter Pump. This pool may contain accessible
potentially hazardous sharp edges or sharp points that are a necessary part of the function of the Filter Pump.
10. If a drain or suction outlet cover is missing or broken, do not use the pool. Suction can cause body part entrapment, hair and jewelry entanglement, evisceration,
or drowning. Repair or replace the drain or suction outlet cover before allowing the pool to be used. During nighttime pool use, artificial lighting shall be used to
illuminate all safety signs, ladders, steps, deck surfaces, and walks.
11. The floor of the pool shall be visible at all times from the outside perimeter of the pool.
12. Post a list of emergency telephone numbers such as the nearest available police, fire, ambulance, and/or rescue unit. These numbers are to be kept near the
telephone, which is closest to the pool.
13. Basic lifesaving equipment, including one of the following should be on hand at all times:
A light, strong, rigid pole (shepherd's crook) not less than twelve feet (12’) [366cm] long.
A minimum one-fourth inch (¼”) [6.35 mm] diameter rope as long as one and one half (1 ½) times the maximum width of the pool or fifty feet (50’) [15.24 meters],
whichever is less, which has been firmly attached to a Coast Guard-approved ring buoy having an outside diameter of approximately fifteen inches (15”) [38.1 cm],
or similarly approved flotation device.
14. Pool shall be located at a minimum distance of 6ft (1.83m) from any receptacle, and all 125-volt 15- and 20-ampere receptacles located within 20ft (6.0m) of the
pool shall be protected by a ground fault circuit interrupter (GFCI), where distances are by measuring the shortest path the supply cord of an appliance connected
to the receptacle would follow, without piercing a floor, wall, ceiling, doorway with hinged or sliding door, window opening, or other effective permanent barrier, to
the inside pool wall.
Circulation Systems
1. Installers shall follow written instructions regarding positioning of all equipment connected to the circulation systems.
2. The installer shall follow written instructions provided for operating the circulation system components.
3. All circulation system components and pump that require replacement or servicing shall be installed according to the pump’s instruction manual.
4. Circulation equipment shall be installed per manufacturer’s instructions to provide proper mounting and support, to prevent damage from misalignment, settlement,
and vibration, and to minimize the potential for the accumulation of debris and moisture. Please refer to pump’s instruction manual.
Chemicals
For safety sake, ensure the deepest part of the pool is always visible. The user must properly maintain the clarity of the pool water at all times. Check the pH and chlorine
levels periodically and make sure they are within the recommended limits. Additional water treatment chemicals might be needed from time to time. Have the water sample
tested by a local pool supply store to determine if additional chemical is needed. Turn on the pump for the recommended hours daily. If you are unsure of the time frames
please refer to support.polygroupstore.com for the recommended Pump Operation Hours based on pool types and sizes. Clean and replace filter cartridge frequently.
Replace only with genuine Polygroup
®
/ Summer Waves
®
Brand filter cartridge. Refer to the Filter Pump manual for additional water care information.
Entrapment Risk
1. Entrapment Avoidance: There shall be no protrusions or other obstruction in the swimming area, which may cause entrapment or entanglement of the user. If
a suction outlet cover is missing or broken, do not use the pool. Suction can cause body part entrapment, hair and jewelry entanglement, evisceration, or drowning.
Repair or replace the suction outlet cover before allowing the pool to be used.
2. DANGER! TO AVOID SERIOUS INJURY OR DEATH, CLOSE THE POOL OR SPA TO BATHERS IF ANY SUCTION OUTLET COVER/GRATE IS MISSING,
BROKEN, OR INOPERATIVE.
3. Never play or swim near drains or suction fittings. Your body or hair may be trapped causing permanent injury or drowning.
4. Never enter the pool or spa if a suction fitting or drain cover is loose, broken, or missing.
5. Immediately notify the pool/spa owner or operator if you find a drain cover loose, broken, or missing.
Drowning Risk
1. Keep unsupervised children from accessing the pool by installing fencing or other approved barriers around all sides of pool. State or local laws or codes may require
fencing or other approved barriers. Check state or local laws and codes before setting up pool.
2. Toys, chairs, tables, or similar objects that a young child could climb shall be at least four feet (4’) [121.92 cm] from the pool. The pump filter system shall be positioned
so as to prevent it being used as a means of access to the pool by young children. Do not leave toys inside pool when finished using, since toys and similar items
might attract a child to the pool.
3. Position furniture (for example: tables, chairs) away from pool and so that children cannot climb on it to gain access to the pool.
Electrocution Risk
1. Keep all electrical lines, radios, speakers, and other electrical appliances away from the pool.
2. Do not place pool near or under overhead electrical lines.
First Aid
1. Keep a working phone and a list of emergency numbers near the pool.
2. Become certified in cardiopulmonary resuscitation (CPR). In the event of an emergency, immediate use of CPR can make a lifesaving difference.
Special Warning
1. Local building codes may require obtaining a building or electrical permit. Installer shall follow regulations on setback, barriers, devices, and other conditions.
2. Safety signs shall comply with requirements of ANSI-Z535 and use signal wording.
3. DO NOT attempt to assemble this pool in adverse weather conditions, windy conditions, or when the temperature is below 60°F.
4. This is a storable filter pump, which should be disassembled and stored when temperatures are expected to fall below 32°F.
Extra Safety Warning
1. Adult supervision is always required.
2. Parents should learn CPR.
3. Keep all electrical radios, speakers, and other appliances away from the swimming pool.
4. When you touch the filter, pump, or electrical parts, be sure the ground under your feet is “Bone Dry.”
5. All electrical outlets should have a GFCI, and connections should be a minimum of 6 feet (1.83 m) from the outside perimeter of the wall of the pool.
From 6–10 feet (1.83–3.05 m), there should be either a fixed connection (outlet box) or twistlock connection with a GFCI.
6. Connect power cords to a 3-wire grounding-type outlet only.
7. Keep all breakable objects out of the pool area.
8. Alcohol consumption and pool activities do not mix. Never allow anyone to swim, dive, or slide under the influence of alcohol or drugs.
9. Severe electrical shock could result if you install your pump or filter on a deck. The pump or filter could fall into the water, causing severe shock or electrocution.
10. Do not install on a deck or other surface at, above, or slightly below the top rail of the pool.
11. Do not use the filter pump during severe weather conditions, i.e. electrical storms, tornadoes, etc.
12. Be aware of overhead power lines when vacuuming your pool or using a telescoping pole.
13. Check regularly for signs of wear or loose bolts that could make the deck unsafe.
14. Please contact pool site dealer or manufacturer for additional safety signs if deemed necessary.
15. For pool service, select a certified pool professional. For additional safety information, see www.APSP.org
Consumer Awareness Booklets and Information Source
Contact: U.S. Consumer Product Safety Commission at www.cpsc.gov/safety-education/safety-guides/pools-and-spas, Pub. #362 “Safety Barrier Guidelines for Home Pools.”
1. The Sensible Way to Enjoy Your Aboveground/Onground Swimming Pool.
2. Children Aren’t Waterproof.
3. Layers of Protection.
4. Pool and Spa Emergency Procedures for Infants and Children.
5. Be Safety Aware Copies of the above brochures are available free from the APSP. Go to: www.APSP.org
Safety Education Programs and Materials
Educational programs and materials (i.e., seminars, workshops, brochures, videos, instructional guides) are available from the APSP, other aquatic safety groups, and
by private firms. As a means of communicating useful safety information to pool owners/operators, and users, industry members are permitted to provide such
information to owners/operators and to request or require owners/operators to sign a statement that they have received, read, and will follow the guidelines.
Other sources of safety information:
• www.cdc.gov
• www.cpsc.gov
• www.drowningpreventionalliance.com
• www.nspf.org
• www.safekids.org
ANSI American National Standards Institute
25 West 43rd Street, New York NY 10036
Contact: 212-642-4900
www.ansi.org
APSP Association of Pool & Spa Professionals
(formerly National Spa and Pool Institute)
2111 Eisenhower Avenue, Suite 500
Alexandria VA 22314-4679
Contact: 703-838-0083
www.apsp.org
OWNER’S MANUAL
ASME American Society of Mechanical Engineers
Two Park Avenue, New York NY 10016-5990
Contact: 800-843-2763 (U.S. & Canada) 973-882-1170 (outside North America)
www.asme.org
NSPI National Spa and Pool Institute (see APSP)
UL Underwriters Laboratories
333 Pfingsten Road,Northbrook IL 60062-2096
Contact: 877-854-3577 or 847-272-8800
www.ul.com
NSF NSF International
P.O. Box 130140
789 N. Dixboro Road
Ann Arbor MI 48105
Contact: 800-673-6275 or 734-769-8010
www.nsf.org
ASTM ASTM International (formerly American Society of Testing & Materials)
100 Barr Harbor Drive, P.O. BOX C700
West Conshohocken, PA 19428-2959
Contact: 877-909-2786 (USA & Canada) or 610-832-9585 (International)
www.astm.org
NEC National Electrical Code (see NFPA)
NFPA National Fire Protection Association
1 Batterymarch Park, Quincy MA 02169-7471
Contact: 800-344-3555 (U.S. & Canada) or 617-770-3000 (International)
www.nfpa.org
Filtration Systems
Any equipment connected to the circulation systems shall be positioned so as to prevent their being used as a means of access to the pool by young children. (See the
latest published edition of ANSI/ APSP-8 Model Barrier Code for Residential Swimming Pools, Spas, and Hot Tubs.)
Barrier
Barriers are necessary to provide protection against potential drowning and near drowning, and barriers are not a substitute for the constant supervision of children.
(See latest published edition of ANSI/APSP-8 Model Barrier Code for Residential Swimming Pools, Spas, and Hot Tubs.)
Risk of Drowning, Entrapment, and Diving Accidents
Publications are available that describe the risk of drowning, entrapment, and diving accidents. Available publications related to pool safety include the Association
of Pool and Spa Professionals’ (APSP) booklets entitled: The Sensible Way to Enjoy Your Aboveground/ Onground Swimming Pool, Children Aren’t Waterproof, Pool
and Spa Emergency Procedures for Infants and Children, Layers of Protection, and the latest published edition of ANSI/APSP-8 Model Barrier Code for
Residential Swimming Pools, Spas, and Hot Tubs.
Installer Responsibilities
All of these components shall be positioned so as to prevent their being used as a means of access to the pool by young children.
(See Barrier Code for Residential Swimming Pools, Spas, and Hot Tubs.)
6
Should you encounter any problems, contact Customer Service at (888) 919-0070 from 8AM to 5PM MST, Monday-Friday.
Extended operating days and hours during peak season requirements.
Safety Care for Children
1. Children, especially children younger than five years, are at high risk of drowning. Drowning occurs silently and quickly and can occur in as little as 2 in. (5 cm) of water.
2. Keep children in your direct sight, stay close, and actively supervise them when they are in or near this pool and when you are filling and emptying this pool.
3. When searching for a missing child, check the pool first, even if the child is thought to be in the house.
4. Locate pumps and filters in such a way that children cannot climb on them and gain access to the pool.
5. WARNING: To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times.
Swimming Pool Barriers
Very Important: Swimming pool barriers, which restrict access to the pool by small children, may be required by law. A barrier is necessary to provide protection against
potential drowning and near drowning. Barriers are not a substitute for constant supervision of children. Check state or local laws and codes before setting up pool.
Swimming Pool Equipment
1. The use of artificial pool lighting is at the discretion of the pool owner. Lighting, when installed, should be in accordance with Article 680 of the
National Electrical Code (NEC) or its latest approved edition and in consultation with a licensed electrical professional.
2. Keep all electrical lines, radios, speakers, and other electrical appliances away from the pool.
3. Do not place pool near or under overhead electrical lines.
4. All electrical components installed in and/or adjacent to an aboveground/onground residential swimming pool shall be installed in accordance with and shall comply
with the requirements of the latest published edition of NFPA 70, National Electrical Code (NEC
®
) Article 680, Swimming pools, fountains, and similar installations,
and any state or local code.
Filter Pump Awareness
1. WARNING: Risk of Electric Shock. Connect only to a grounding type receptacle. This product is provided with a ground-fault circuit-interrupter. If replacement of
the plug or cord is needed, use only identical replacement parts.
2. WARNING: To reduce the risk of electric shock, replace damaged cord immediately.
3. WARNING: To reduce the risk of electric shock, do not use extension cord to connect unit to electric supply; provide a properly located outlet.
4. CAUTION: To reduce the risk of electric shock, the pool must be installed no closer than 6 feet (1.8m) from any electrical outlet. Do not place portable appliances
closer than 5 feet (1.5m) from the pool.
5. CAUTION: This pump is for use with storable pools only. Do not use with permanently-installed pools. A storable pool is constructed so that it is capable of being
readily disassembled for storage and reassembled to its original integrity. A permanently-installed pool is constructed in or on the ground or in a building such that it
cannot be readily disassembled for storage.
6. CAUTION: For continued protection against possible electric shock, this unit is to be mounted to the base in accordance with the installation instructions.
7. Do not bury cord. Locate cord to minimize abuse from lawn mowers, hedge trimmers, and other equipment.
8. The unit is provided with a ground-fault circuit-interrupter (GFCI). To test the GFCI, push the test button. The GFCI should interrupt power. Push the reset button.
Power should be restored. If the GFCI fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the pump without the test button being
pushed, a ground current is flowing, indicating the possibility of an electric shock. Do not use this pump. Disconnect the pump, and have the problem corrected by
a qualified service representative before using.
9. The Filter Pump is to be assembled by an adult; care should be taken in the unpacking and assembling of the Filter Pump. This pool may contain accessible
potentially hazardous sharp edges or sharp points that are a necessary part of the function of the Filter Pump.
10. If a drain or suction outlet cover is missing or broken, do not use the pool. Suction can cause body part entrapment, hair and jewelry entanglement, evisceration,
or drowning. Repair or replace the drain or suction outlet cover before allowing the pool to be used. During nighttime pool use, artificial lighting shall be used to
illuminate all safety signs, ladders, steps, deck surfaces, and walks.
11. The floor of the pool shall be visible at all times from the outside perimeter of the pool.
12. Post a list of emergency telephone numbers such as the nearest available police, fire, ambulance, and/or rescue unit. These numbers are to be kept near the
telephone, which is closest to the pool.
13. Basic lifesaving equipment, including one of the following should be on hand at all times:
A light, strong, rigid pole (shepherd's crook) not less than twelve feet (12’) [366cm] long.
A minimum one-fourth inch (¼”) [6.35 mm] diameter rope as long as one and one half (1 ½) times the maximum width of the pool or fifty feet (50’) [15.24 meters],
whichever is less, which has been firmly attached to a Coast Guard-approved ring buoy having an outside diameter of approximately fifteen inches (15”) [38.1 cm],
or similarly approved flotation device.
14. Pool shall be located at a minimum distance of 6ft (1.83m) from any receptacle, and all 125-volt 15- and 20-ampere receptacles located within 20ft (6.0m) of the
pool shall be protected by a ground fault circuit interrupter (GFCI), where distances are by measuring the shortest path the supply cord of an appliance connected
to the receptacle would follow, without piercing a floor, wall, ceiling, doorway with hinged or sliding door, window opening, or other effective permanent barrier, to
the inside pool wall.
Circulation Systems
1. Installers shall follow written instructions regarding positioning of all equipment connected to the circulation systems.
2. The installer shall follow written instructions provided for operating the circulation system components.
3. All circulation system components and pump that require replacement or servicing shall be installed according to the pump’s instruction manual.
4. Circulation equipment shall be installed per manufacturer’s instructions to provide proper mounting and support, to prevent damage from misalignment, settlement,
and vibration, and to minimize the potential for the accumulation of debris and moisture. Please refer to pump’s instruction manual.
Chemicals
For safety sake, ensure the deepest part of the pool is always visible. The user must properly maintain the clarity of the pool water at all times. Check the pH and chlorine
levels periodically and make sure they are within the recommended limits. Additional water treatment chemicals might be needed from time to time. Have the water sample
tested by a local pool supply store to determine if additional chemical is needed. Turn on the pump for the recommended hours daily. If you are unsure of the time frames
please refer to support.polygroupstore.com for the recommended Pump Operation Hours based on pool types and sizes. Clean and replace filter cartridge frequently.
Replace only with genuine Polygroup
®
/ Summer Waves
®
Brand filter cartridge. Refer to the Filter Pump manual for additional water care information.
Entrapment Risk
1. Entrapment Avoidance: There shall be no protrusions or other obstruction in the swimming area, which may cause entrapment or entanglement of the user. If
a suction outlet cover is missing or broken, do not use the pool. Suction can cause body part entrapment, hair and jewelry entanglement, evisceration, or drowning.
Repair or replace the suction outlet cover before allowing the pool to be used.
2. DANGER! TO AVOID SERIOUS INJURY OR DEATH, CLOSE THE POOL OR SPA TO BATHERS IF ANY SUCTION OUTLET COVER/GRATE IS MISSING,
BROKEN, OR INOPERATIVE.
3. Never play or swim near drains or suction fittings. Your body or hair may be trapped causing permanent injury or drowning.
4. Never enter the pool or spa if a suction fitting or drain cover is loose, broken, or missing.
5. Immediately notify the pool/spa owner or operator if you find a drain cover loose, broken, or missing.
Drowning Risk
1. Keep unsupervised children from accessing the pool by installing fencing or other approved barriers around all sides of pool. State or local laws or codes may require
fencing or other approved barriers. Check state or local laws and codes before setting up pool.
2. Toys, chairs, tables, or similar objects that a young child could climb shall be at least four feet (4’) [121.92 cm] from the pool. The pump filter system shall be positioned
so as to prevent it being used as a means of access to the pool by young children. Do not leave toys inside pool when finished using, since toys and similar items
might attract a child to the pool.
3. Position furniture (for example: tables, chairs) away from pool and so that children cannot climb on it to gain access to the pool.
Electrocution Risk
1. Keep all electrical lines, radios, speakers, and other electrical appliances away from the pool.
2. Do not place pool near or under overhead electrical lines.
First Aid
1. Keep a working phone and a list of emergency numbers near the pool.
2. Become certified in cardiopulmonary resuscitation (CPR). In the event of an emergency, immediate use of CPR can make a lifesaving difference.
Special Warning
1. Local building codes may require obtaining a building or electrical permit. Installer shall follow regulations on setback, barriers, devices, and other conditions.
2. Safety signs shall comply with requirements of ANSI-Z535 and use signal wording.
3. DO NOT attempt to assemble this pool in adverse weather conditions, windy conditions, or when the temperature is below 60°F.
4. This is a storable filter pump, which should be disassembled and stored when temperatures are expected to fall below 32°F.
Extra Safety Warning
1. Adult supervision is always required.
2. Parents should learn CPR.
3. Keep all electrical radios, speakers, and other appliances away from the swimming pool.
4. When you touch the filter, pump, or electrical parts, be sure the ground under your feet is “Bone Dry.”
5. All electrical outlets should have a GFCI, and connections should be a minimum of 6 feet (1.83 m) from the outside perimeter of the wall of the pool.
From 6–10 feet (1.83–3.05 m), there should be either a fixed connection (outlet box) or twistlock connection with a GFCI.
6. Connect power cords to a 3-wire grounding-type outlet only.
7. Keep all breakable objects out of the pool area.
8. Alcohol consumption and pool activities do not mix. Never allow anyone to swim, dive, or slide under the influence of alcohol or drugs.
9. Severe electrical shock could result if you install your pump or filter on a deck. The pump or filter could fall into the water, causing severe shock or electrocution.
10. Do not install on a deck or other surface at, above, or slightly below the top rail of the pool.
11. Do not use the filter pump during severe weather conditions, i.e. electrical storms, tornadoes, etc.
12. Be aware of overhead power lines when vacuuming your pool or using a telescoping pole.
13. Check regularly for signs of wear or loose bolts that could make the deck unsafe.
14. Please contact pool site dealer or manufacturer for additional safety signs if deemed necessary.
15. For pool service, select a certified pool professional. For additional safety information, see www.APSP.org
Consumer Awareness Booklets and Information Source
Contact: U.S. Consumer Product Safety Commission at www.cpsc.gov/safety-education/safety-guides/pools-and-spas, Pub. #362 “Safety Barrier Guidelines for Home Pools.”
1. The Sensible Way to Enjoy Your Aboveground/Onground Swimming Pool.
2. Children Aren’t Waterproof.
3. Layers of Protection.
4. Pool and Spa Emergency Procedures for Infants and Children.
5. Be Safety Aware Copies of the above brochures are available free from the APSP. Go to: www.APSP.org
Safety Education Programs and Materials
Educational programs and materials (i.e., seminars, workshops, brochures, videos, instructional guides) are available from the APSP, other aquatic safety groups, and
by private firms. As a means of communicating useful safety information to pool owners/operators, and users, industry members are permitted to provide such
information to owners/operators and to request or require owners/operators to sign a statement that they have received, read, and will follow the guidelines.
Other sources of safety information:
• www.cdc.gov
• www.cpsc.gov
• www.drowningpreventionalliance.com
• www.nspf.org
• www.safekids.org
ANSI American National Standards Institute
25 West 43rd Street, New York NY 10036
Contact: 212-642-4900
www.ansi.org
APSP Association of Pool & Spa Professionals
(formerly National Spa and Pool Institute)
2111 Eisenhower Avenue, Suite 500
Alexandria VA 22314-4679
Contact: 703-838-0083
www.apsp.org
ASME American Society of Mechanical Engineers
Two Park Avenue, New York NY 10016-5990
Contact: 800-843-2763 (U.S. & Canada) 973-882-1170 (outside North America)
www.asme.org
NSPI National Spa and Pool Institute (see APSP)
UL Underwriters Laboratories
333 Pfingsten Road,Northbrook IL 60062-2096
Contact: 877-854-3577 or 847-272-8800
www.ul.com
NSF NSF International
P.O. Box 130140
789 N. Dixboro Road
Ann Arbor MI 48105
Contact: 800-673-6275 or 734-769-8010
www.nsf.org
ASTM ASTM International (formerly American Society of Testing & Materials)
100 Barr Harbor Drive, P.O. BOX C700
West Conshohocken, PA 19428-2959
Contact: 877-909-2786 (USA & Canada) or 610-832-9585 (International)
www.astm.org
NEC National Electrical Code (see NFPA)
NFPA National Fire Protection Association
1 Batterymarch Park, Quincy MA 02169-7471
Contact: 800-344-3555 (U.S. & Canada) or 617-770-3000 (International)
www.nfpa.org
Filtration Systems
Any equipment connected to the circulation systems shall be positioned so as to prevent their being used as a means of access to the pool by young children. (See the
latest published edition of ANSI/ APSP-8 Model Barrier Code for Residential Swimming Pools, Spas, and Hot Tubs.)
Barrier
Barriers are necessary to provide protection against potential drowning and near drowning, and barriers are not a substitute for the constant supervision of children.
(See latest published edition of ANSI/APSP-8 Model Barrier Code for Residential Swimming Pools, Spas, and Hot Tubs.)
Risk of Drowning, Entrapment, and Diving Accidents
Publications are available that describe the risk of drowning, entrapment, and diving accidents. Available publications related to pool safety include the Association
of Pool and Spa Professionals’ (APSP) booklets entitled: The Sensible Way to Enjoy Your Aboveground/ Onground Swimming Pool, Children Aren’t Waterproof, Pool
and Spa Emergency Procedures for Infants and Children, Layers of Protection, and the latest published edition of ANSI/APSP-8 Model Barrier Code for
Residential Swimming Pools, Spas, and Hot Tubs.
Installer Responsibilities
All of these components shall be positioned so as to prevent their being used as a means of access to the pool by young children.
(See Barrier Code for Residential Swimming Pools, Spas, and Hot Tubs.)
SAVE THESE INSTRUCTIONS
7
OWNER’S MANUAL
Should you encounter any problems, contact Customer Service at (888) 919-0070 from 8AM to 5PM MST, Monday-Friday.
Extended operating days and hours during peak season requirements.
1. READ ALL INSTRUCTIONS CAREFULLY and get a thorough understanding of what is required to assemble your RP series Filter Pump.
2. It is recommended that you have some petroleum jelly (not included) on hand for lubricating the gaskets.
FILTER PUMP MODEL
RP350
RP400
WATTAGE
20 Watts
25 Watts
AMPERAGE
0.35 Amps
0.2 Amps
FILTER PUMP POWER INFORMATION
PARTS LIST
PRELIMINARY STEPS
FILTER PUMP IMPORTANT NOTES
OWNER’S MANUAL
1. Installer shall follow written instructions provided for operation of the filter pump systems.
2. All electrical components shall be installed in accordance with Article 680 of the National Electrical Code (NEC) “Swimming Pools, Fountains and Similar Installations”
or its latest approved edition.
3. The Type D Filter Cartridge 18 will hold as many as 2 of the 1” diameter chlorine tablets. Check your chlorine levels to determine the proper number of chlorine
tablets to add. The filter cartridge will automatically dispense chlorine into the pool as the Filter Pump runs. You must have the type of Filter Cartridge with a central
core mesh divider (See page 9) to use the chlorine dispenser.
DO NOT use this to dispense powdered chlorine, shock treatment, or any other type of chemicals as damage to the pump, filter cartridge, and pool will occur.
4. The RP Series Filter Pump systems are manufactured by Polygroup
®
and ETL control number 4000608 and 4006317 - double insulated and grounded - 120 Volts
A.C. - 60 Hz. (All unit must have a minimum of 105 Volts A.C. to start and run properly.)
ITEMSQTY.
2
1
1
2
1
1
1
1
2
4
1
1
1
1
1
PARTS NAME
Fitting Gasket
Suction Fitting
Suction Fitting Washer (SF Washer)
Return/Suction Fitting Lock Nut
Suction Fitting Cap (SF/Service Cap)
Return Fitting
Return Fitting Diverter (RF Diverter)
Return Fitting Plug (RF/Service Plug)
Hose
Hose Camp
Filter Pump Assembly
A) RP350
B) RP400
Vent Screw
Vent Screw O-Ring
Seal Top
Canister Gasket
QTY.
1
1
1
1
1
1
1 set
1
2
1 set
PARTS NAME
Filter Pump Canister
Motor Assembly
A) RP350
B) RP400
Type D Filter Cartridge
Pump Motor Body
A) RP350
B) RP400
Rotor Assembly
A) RP350
B) RP400
Volute Housing
Volute Housing Screw Set (2 ea.)
GFCI Power Cord Set (image reference only)
Filter Pump Port / Fitting O-Ring
Motor Assembly Screw and Washer Set (4 ea.)
ITEMS
1
2
3
4
5
6
7
8
9
8
Should you encounter any problems, contact Customer Service at (888) 919-0070 from 8AM to 5PM MST, Monday-Friday.
Extended operating days and hours during peak season requirements.
9
7 5
6
24
1
4
8
11
RETURN FITTING
2
24
1
3
4
10
SUCTION FITTING
RP350 / RP400
23
9
OWNER’S MANUAL
Should you encounter any problems, contact Customer Service at (888) 919-0070 from 8AM to 5PM MST, Monday-Friday.
Extended operating days and hours during peak season requirements.
12
13
14
15
17B
18
16
RP400
24
25
RP350
20A
19A
20B
21
22
19B
24
24
21
22
24
24
12
13
14
15
18
16
24
17 A
25
10
Should you encounter any problems, contact Customer Service at (888) 919-0070 from 8AM to 5PM MST, Monday-Friday.
Extended operating days and hours during peak season requirements.
1. Set up the pool by following all the instructions that come with the pool. Do not
fill with water until the Filter Pump is properly installed. Locate the Outlet and
Inlet openings on the pool wall.
3. Lubricate the Fitting Gasket with petroleum jelly (not included)
and install the Return Fitting on the Inlet opening of the pool.
2. Lubricate the Fitting Gasket with petroleum jelly (not included) and
install the Suction Fitting on the Outlet opening of the pool.
SETUP INSTRUCTIONS
4. Remove the Filter Pump , Hoses , and Hose Clamps from
the package.
9
10
11
WARNING:
CLIMBING HAZARD! PLEASE PREVENT CHILDREN FROM CLIMBING ON THE FILTER CANISTER TO GAIN ACCESS TO THE POOL.
Before assembling your product, please take a few minutes to check the contents and become familiar with all the parts.
11
9
10
7
6
1
4
4
3
1
2
Inlet
Outlet
Outside Pool Wall
Outside Pool Wall
Inside Pool Wall
Inside Pool Wall
OWNER’S MANUAL
11
Should you encounter any problems, contact Customer Service at (888) 919-0070 from 8AM to 5PM MST, Monday-Friday.
Extended operating days and hours during peak season requirements.
8. Do not plug in the filter pump at this point. Begin to fill the pool with water
until the water level reaches the fill line.
5. Lubricate the O-rings on the Suction Fitting and the Filter Pump Inlet
with petroleum jelly (not included). Connect the Hose 9 from the
Suction Fitting 10 to the Filter Pump Inlet.
6. Lubricate the O-rings on the Return Fitting and the Filter Pump Outlet
with petroleum jelly (not included). Connect the Hose 9 from
the Return Fitting to the Filter Pump Outlet.
7. Tighten all Hose Clamps 10 to prevent water leakage.
9. Air is now trapped inside the Filter Pump system, which will prevent the
water from flowing smoothly. To VENT the system (release the
trapped air), open the Vent Screw 12 at the top of the pump by
turning it counter-clockwise. The water pressure will force out all the
trapped air inside the Filter Pump system. Tighten the Vent Screw 12
when you see water flowing out from the Seal Top 14 .
10. Adjust the Return Fitting Diverter 7 to maximize the circulation of the
pool water.
9
10
7
360°
4
9
10
14
12
14
12
Fill Line
Inside Pool Wall
It is recommended to point the diverter
down and away from the suction or
water intake for optimum pool circulation.
12
Should you encounter any problems, contact Customer Service at (888) 919-0070 from 8AM to 5PM MST, Monday-Friday.
Extended operating days and hours during peak season requirements.
USE OF PUMP
IMPORTANT! Your filter pump is protected by a thermal switch. The switch senses the temperature of the filter pump. If it gets too hot, the switch will stop the
pump from running until it cools off. This is a safety device to prevent pump damage and prolong service life. If your pump is automatically turning off, it is because of
high pool water temperature and/or low water flow through the pump. If this happens you need to check the water flow and correct it if needed, as this filter pump uses the
water flow for cooling. It is recommended that you run the pump at night or early morning when the temperature is lower to prevent overheating.
PUMP MOTOR CARE
1. Turn off and unplug the Pump. Remove the RF Diverter 7 from the
Return Fitting 6 and plug with the Service Plug 8 . Hand tighten the
Service Cap 5 onto the Suction Fitting 2 .
2. To depressurize the Filter Pump system, vent the filter pump by twisting
the Vent Screw 12 counter-clockwise.
3. Use both hands to twist off the Seal Top 14 by turning counter-clockwise.
Remove the Filter Cartridge 18 .
4. The filter cartridge can be cleansed of coarse dirt and debris by
thoroughly pressure washing inside and out with a garden hose,
making sure to wash between all pleats. Allow a few hours for
the filter to fully dry and CAREFULLY BRUSH the pleats to
avoid damaging the filter cartridge. DO NOT scrub the pleated
surface areas. Cleaning and scrubbing a filter too vigorously will
wear out the cartridge much faster than if it is simply
hosed off correctly.
5. After you finished cleaning the filter cartridge, liberally lubricate the
GASKET 15 with petroleum jelly and re-assemble in reverse order.
Before restarting the filter pump, be sure to remove the Service Plug 8
and Service Cap 5 .
14
18
FILTER CARTRIDGE USE & CARE
5
2
8
7
6
14
12
14
12
Inside Pool Wall
IMPORTANT: Do NOT connect to a timer device!
Press
"RESET"
Button
To Start
Pump
Operation
How to use the GFCI plug
*Do not connect
to a timer device
23
1. Plug the GFCI Power Cord Set 23 to a properly grounded receptacle at least 15 feet (4.5m) away from the pool.
2. To turn on the Pump, press the RESET button of the GFCI Plug.
3. From inside the pool, check if the water flow from the RF Diverter 7 is correct. It should feel like a solid stream of water
returning to the pool. If not, or if you feel a reduction in flow, clean or replace the Filter Cartridge 18 . For details, see
FILTER CARTRIDGE USE & CARE below as well as Symptom 2 of TROUBLESHOOTING GUIDE (p. 14).
4. To turn the Pump off, press the TEST button of the GFCI Plug, and unplug it from the power outlet.
5. VERY IMPORTANT: Check and adjust the pH and chlorine levels daily.
FILTER PUMP ALONE WILL NOT PREVENT ALGAE FROM GROWING IN POOL WATER;
THIS CAN ONLY BE DONE BY MAINTAINING PROPER CHLORINE AND pH LEVELS AT
ALL TIMES. For details, see POOL WATER CARE (p. 13).
OWNER’S MANUAL
13
Should you encounter any problems, contact Customer Service at (888) 919-0070 from 8AM to 5PM MST, Monday-Friday.
Extended operating days and hours during peak season requirements.
POOL MAINTENANCE
NOTE :
1. Hot weather/heavy use may require pH and chlorine levels to be maintained on the upper side of the scale and superchlorination of the pool every week.
2. Using a pool cover and/or solar cover (available at polygroupstore.com) will assist in maintaining your pH and chlorine levels by reducing the amount of evaporation
from your pool.
CAUTION - Concentrated chlorine levels and low pH levels will damage pool. You must follow the instructions for the pool chemicals you use, as to quantity and
recommended usage. NEVER drop lumps or pellets of chemicals in pool; this may present a hazard to swimmers and/or damage your liner.
1. The following items are required to get your pool ready for use. They are available at polygroupstore.com or
your local pool supplies stores:
Test Kit - Used to check chlorine and pH levels.
1” Chlorine Tablets - Used to disinfect pool water and help control the growth of algae.
pH Control Chemicals - Used to adjust pH levels Up (Soda Ash) or Down (Acid).
Algaecides - Used to eliminate algae.
Superchlorinator - Used to destroy combined chlorine, ammonia, nitrogen, and organic compounds.
Leaf / Skimmer Net with handle - Used to remove leaves, trash, insects, etc. from your pool.
This item can be purchased at polygroupstore.com.
Chlorine Dispenser (Supplied with Polygroup
®
’s patented Filter Cartridge U.S. Pat. 7,005,062) - Used to
dispense 1” chlorine tablets ONLY.
2. Use test kit daily to check pH and chlorine levels. Adjust accordingly using the required chemicals.
NOTE: Excessive levels of chlorine or low pH levels will damage pool liner.
3. The pool can be cleaned using a garden hose powered vacuum from Polygroup
®
or a pool supply store.
4. Using a foot bath near the pool to wash off your feet prior to entering the pool will assist in keeping the pool clean.
5. Well water often presents special problems with water chemistry. If you must use well water, take a sample to your local pool chemical supplier for analysis before
adding ANY chemicals.
6. Refer to the retail package box or visit the support pages at support.polygroupstore.com for the capacity of your pool. You will need this
information to determine the amount of chemicals you will need to correct the pool water. NOTE: It is recommended to use a 5 gallon bucket of water to mix and
dissolve your chemicals and then applying directly to the pool water. Follow manufacturers label directions on all chemicals. *Most pool supply stores will test your
pool water for free and advise you of what chemicals you need, and the correct amount to use for your pool. You will need to tell them the pool capacity in gallons.
7. IMPORTANT - We cannot emphasize enough the importance of proper and adequate daily chemical treatment. Chlorine and pH levels must be properly
maintained at all times. PUMP AND FILTER ALONE WILL NOT PREVENT ALGAE FROM GROWING IN POOL WATER; THIS CAN ONLY BE DONY BE
MAINTAINING PROPER CHLORINE AND pH LEVELS AT ALL TIMES.
Maintain pH level between 7.3 and 7.8.
Maintain chlorine level between 1.0 and 1.6 ppm (parts per million).
Superchlorinate your pool at least every other week.
POOL WATER CARE
6. Suntan oils, body oils, and algae can form a coating on the filter pleats which may not be thoroughly removed by hosing. Such films of oils and/or algae will rapidly
clog up the filters’ pores, greatly reducing filtration. Therefore, it is imperative to remove such materials from the filter element as soon as possible. To remove oils,
we recommend soaking the cartridge in a solution of 1 lb. of tri-sodium phosphate (TSP or any other strong detergent) to 5 gallons of water for up to 12 hours.
Tri-sodium phosphate is available in many supermarkets, hardware stores, or janitorial supply stores. After the oils have been removed, rinse the filter cartridge to
remove any dirt. If algae is a problem, add 1/2 pint of pool chlorine or 1 pint of liquid household bleach to the cleaning solution, 1 hour before removing the filter
cartridge from the solution. Thoroughly rinse the filter cartridge before replacing it in the filter case. Check the pool chemistry to determine the cause of algae growth.
7. Excessive calcium and/or mineral deposits may build up on a filter cartridge and should be handled differently. Contact your local pool supply store to ask about
additional filter cartridge cleaners or treatment for calcium or mineral deposits. Check pool chemistry for high pH or alkalinity; this may cause a calcium or mineral
build-up.
8. A spare “stand-by” Filter Cartridge 18 is an excellent investment. It provides a convenient way to continue filtration of your pool while cleaning or replacing a dirty
Filter Cartridge 18 . Also, a well-maintained, clean cartridge assures you that your filter will always be ready to operate at peak efficiency.
9. Filter cartridges may be purchased at the store you purchased your pool from, or ordered from Polygroup
®
at polygroupstore.com. Always replace with genuine
Polygroup
®
SUMMER WAVES
®
filter cartridges.
Chlorine Tablets
1. Check and adjust pH and chlorine levels daily using required chemicals. See Section “POOL WATER CARE.” or contact your local pool store.
2. Check filter pump output daily. If flow is reduced, see Symptom 2 in Section “TROUBLESHOOTING GUIDE.”
3. Check filter pump, hoses and fitting for leaks. If a leak is found, see Symptom 4 in Section “TROUBLESHOOTING GUIDE.”
4. Run the pump for the recommended number of hours daily. If you are unsure of the time frame please refer to support.polygroupstore.com for the recommended
"Pump Operation Hours" bases on pool types and sizes.
14
Should you encounter any problems, contact Customer Service at (888) 919-0070 from 8AM to 5PM MST, Monday-Friday.
Extended operating days and hours during peak season requirements.
1
2
3
4
SYMPTOM CAUSE SOLUTION
Motor fails to
start or kicks
on and off
A Unit must be plugged into a 3-wire grounded power outlet. Press the reset button on
the GFCI to start the pump.
B Reset the GFCI plug and/or circuit breaker. If problem persists, have the circuit
checked by a qualified electrician.
C Check the line voltage, it must be in the range of 105 to 125 Volts A.C.
No flow or slow
water flow through
the return hose.
Filter pump is not
cleaning the pool
properly (e.g. cloudy/
green water)
Water leakage
A Fill the pool to the fill line. The suction fitting must be at least 4” under water.
A Maintain chlorine level between 1.0 to 1.6 ppm.
B Maintain pH level between 7.3 to 7.8.
C Clean or replace the filter cartridge (See p. 12). A spare cartridge makes servicing
more convenient.
A Make sure the hose clamp 10 is positioned properly over the hose and O-ring 24
to ensure a proper seal. Adjust hose clamp, check o-ring and re-tighten.
Check hose for any holes or cracks and replace if needed.
D Inspect the filter cartridge for holes or tears. If visibly damaged; replace the filter
cartridge
E Check for obstructions in the suction hose or fitting and in the return hose or fitting.
F Have water tested at pool supply store. It may be necessary to add other chemicals
due to varying water quality in different localities.
G Chemicals are required to maintain clean pool water. Clean pool and filter more often.
B Check for obstructions in the suction hose or fitting and in the return hose or fitting.
A Unit not plugged in or
GFCI not activated
B GFCI Plug and/or circuit
breaker tripped
C Low voltage
A Low pool water level
A Chlorine level is not in
the suitable range
B pH level is not in the
suitable range
C Dirty filter cartridge
D Damaged filter
cartridge
E Slow water flow
F Other Chemicals Required
G Pool water very dirty
B Inlet/Outlet clogged
C Dirty filter cartridge
A Hose area: Suction or
Return hose does not fit well
on canister connections and/
or wall fitting connections
B Vent screw in Seal Top
C Seal Top
C Clean or replace the filter cartridge (See p. 12). A spare cartridge makes servicing
more convenient.
B Check O-ring 13 for damage. Replace if needed. Tighen the Vent Screw 12 .
C Check Gasket 15 for damage. Replace if needed. Tighten the Seal Top 14 .
TROUBLESHOOTING GUIDE
POOL PUMP DISASSEMBLY & STORAGE
WARNING: TURN OFF THE PUMP AND UNPLUG THE POWER CORD BEFORE TROUBLESHOOTING THE FILTER PUMP.
1. First turn the pump off and unplug the main power cord of the system. Remove the RF Diverter 7 from the Return Fitting 6 and then seal the Return Fitting 6
with the Service Plug 8 . Hand tighten the Service Cap 5 onto the Suction Fitting 2 .
2. Slowly unscrew the Vent Screw 12 from the Seal Top 14 to depressurize the pump.
3. Remove the Seal Top 14 by turning it counter-clockwise.
4. Remove the Filter Cartridge 18 and remove any chlorine tablets left inside the core section of the filter.
5. Loosen all four Hose Clamps 10 , remove the Hoses 9 and allow water to drain out.
6. Clean and dry all filter pump parts including the Filter Cartridge.
7. Liberally lubricate the O-ring 13 and Gasket 15 with petroleum jelly, and then reassemble them, along with the Seal Top 14 and Vent Screw 12 , onto the
Canister 16 . Store all parts carefully in an airtight plastic bag.
8. Store all the parts in a dry environment that remains above 32 degrees Fahrenheit at all times.
OWNER’S MANUAL
15
Should you encounter any problems, contact Customer Service at (888) 919-0070 from 8AM to 5PM MST, Monday-Friday.
Extended operating days and hours during peak season requirements.
1. First turn the pump off and unplug the main power cord of the system. Remove the RF Diverter 7 from the Return Fitting 6 and then seal the Return Fitting 6
with the Service Plug 8 , Hand tighten the Service Cap 5 onto the Suction Fitting 2 .
2. Slowly unscrew the Vent Screw 12 from the Seal Top 14 to depressurize the pump.
3. Loosen the Hose Clamps 10 at the filter pump inlet and outlet. Detach both Hoses 9 from the filter pump.
4. Turn the filter pump upside down. Remove the Motor Assembly Washer and Screw Set 25 .
(REMEMBER TO KEEP ALL PARTS IN A SAFE PLACE FOR REASSEMBLY LATER)
1. To replace the Rotor Assembly 20 , remove the Volute Housing Screw Set 22 . Grasp the Pump Motor Body in one hand and the volute cover discharge
nozzle in the other hand. Rotate the nozzle counterclockwise to release the tabs of volute housing from the brackets of pump body.
2. Carefully pull upwards once the tabs are clear of the brackets.
3. Remove the Volute Housing 21 and pull out the Rotor Assembly 20 from the Pump Motor Body 19 . Please be careful as the Rotor Assembly has multiple parts
which may come out separately.
4. Inspect the Rotor Assembly to make sure that it has all of its parts and that the Rotor Shaft, Magnet Axle, or Impeller are not broken as this will cause the pump
to fail. If your Rotor Assembly is broken, a complete Rotor Assembly may be purchased at polygroupstore.com without having to replace the whole pump.
PUMP REMOVAL INSTRUCTIONS FOR TROUBLESHOOTING
ROTOR INSPECTION AND REPLACEMENT INSTRUCTIONS
16
16
17
17
25
(REMEMBER TO KEEP ALL PARTS IN A SAFE PLACE FOR REASSEMBLY LATER)
5. Remove the Motor Assembly 17 from the Canister 16 . .
16
Should you encounter any problems, contact Customer Service at (888) 919-0070 from 8AM to 5PM MST, Monday-Friday.
Extended operating days and hours during peak season requirements.
5. Please see Pool Support - Filtration System Troubleshooting for the RP350/RP400 Filtration System at support.polygroupstore.com.
PLEASE NOTE: Even if the rotor assembly is in perfect condition; if it is not seated properly between the volute housing and the pump it will not function correctly.
6. To reassemble the pump (Motor Assembly): Carefully insert the Rotor Assembly 20 into the Pump Motor Body 19 . The force of the magnet will pull the rotor
assembly into the pump. Ensure that the Rotor Assembly is completely assembled and aligned correctly inside the pump body.
7. Once the rotor has been inserted, fasten the volute housing tabs back under the brackets of pump body by turning the volute housing discharge nozzle clockwise.
8. Tighten the Volute Housing 21 With the Volute Cover Screw Set 22 to complete the reassembly of the pump (Motor Assembly).
9. Slowly insert the Motor Assembly 17 back into the Canister 16 , and fasten the Motor Assembly 17 With Motor Assembly Washer and Screw Set 25 .
19
20
21
22
Volute Hosing
Discharge Nozzle
Slide the tabs of Volute Housing
underneath the brackets of
Pump Body to lock
Brackets on pump body
Rotor Assembly
Shaft End Cap
Washer
Impeller
Magnet Axle
Rotor Shaft
(This shaft should go through
all the parts and into both
Shaft End Caps)
Washer
Shaft End Cap
pump body
Volute Housing Screws
OWNER’S MANUAL
17
Should you encounter any problems, contact Customer Service at (888) 919-0070 from 8AM to 5PM MST, Monday-Friday.
Extended operating days and hours during peak season requirements.
KEY DESCRIPTION
RP400RP350
PART #
1
2
3
4
5
6
7
8
9
10
12
13
14
15
16
17
18
20
21
22
24
*
*
*
Fitting Gasket
Suction Fitting
Suction Fitting Washer (SF Washer)
Return/Suction Fitting Lock Nut
Suction Fitting Cap (SF/Service Cap)
Return Fitting
Return Fitting Diverter (RF Diverter)
Return Fitting Plug (RF/Service Plug)
Hose
Hose Clamp
Vent Screw
Vent Screw O-Ring
Seal Top
Canister Gasket
Filter Pump Canister
Motor Assembly
Type D Filter Cartridge
Rotor Assembly
Volute Housing
Volute Cover Screw Set
Filter Pump Port / Fitting O-Ring
59” Hose
1-1/4” to 1-1/2” Rubber Fitting Adapter
For RP Series Filter Pump sold separately
P58PF1520K01
P58281283W05
P58PF1510K01
P58PF1430W05
P58PF2820P01
P58PF7800W05
P58PF7790W05
P58PF0620K01
P58125036W01
P58220221W05
P58534000W05
P58031000K01
P58PF5290W05
P58096000K01
P58530000W05
P53F0350C000
P581041037PR
P58050350001
P58PF5270K01
P5816300270B
P58030001K01
P584150006W1
P58PF5620P01
P53FR0350W05
P58PF1520K01
P58281283W05
P58PF1510K01
P58PF1430W05
P58PF2820P01
P58PF7800W05
P58PF7790W05
P58PF0620K01
P58125036W01
P58220221W05
P58534000W05
P58031000K01
P58PF5290W05
P58096000K01
P58530000W05
P58F0400C000
P581041037PR
P58050400001
P58PF5270K01
P5816300270B
P58030001K01
P584150006W1
P58PF5620P01
P53FR0400W05
REPLACEMENT PARTS ORDERING INFO
OWNER’S MANUAL
18
Should you encounter any problems, contact Customer Service at (888) 919-0070 from 8AM to 5PM MST, Monday-Friday.
Extended operating days and hours during peak season requirements.
ASME COMPLIANT SUCTION FITTING INFO
9. PSF-100A or PSF-100B Suction Outlet Fitting is to be replaced every 5 years.
10. No tool is required for installation.
11. Service & winterizing instructions:
a. CAUTION! DO NOT EXCEED THE MAXIMUM ALLOWABLE FLOW RATE: 24 gallons per minute (1,440 gallons per hour)
b. Carefully observe and inspect the suction outlet fitting for damage and tampering. Missing, broken or cracked suction outlet fitting must be replaced before
each use of your pool.
c. Loose suction outlet fitting should be reattached or replaced before each use of your pool.
d. Remove and store the suction outlet fitting assembly if temperatures are expected to fall below 32°F (0°C).
1. PSF-100A and PSF-100B Suction Outlet Fitting are certified by IAPMO in accordance with the ASME/ANSI/APSP/ICC-16 2011 Suction Fittings for Use in
Swimming Pools, Wading Pools, Spas, and Hot Tubs.
2. This is a submerged suction outlet fitting for use with aboveground swimming pool.
3. For single drain only. Use only ONE outlet fitting for each pump.
4. Do not locate this suction outlet fitting on sitting areas or on the backrest for such seating area.
5. Install this outlet fitting at location recommended by the pool manufacturer. Maximum height 1.8 m from the ground.
6. The maximum allowable flow rate of this suction outlet fitting is 24 gallons per minute (1,440 gallons per hour).
7. Connection hose:
a. Model PSF-100A is to be connected with 1 ¼” (31.8mm) diameter hose.
b. Model PSF-100B is to be connected with 1 ½” (38.1mm) diameter hose.
8. The suction outlet fitting is to be mounted at the suction outlet fitting opening as specified by the manufacturer of the aboveground pool. The diameter of this
opening should be within the range of 1.77” to 1.85” (45mm to 47mm). Refer to the following diagram for detailed assembly instructions:
PSF-100A and PSF-100B Suction Outlet Fitting (For Aboveground Pool)
Swimming Pool
Hose
Hose Clamp
Lock Nut, to be tightened by hand
Rubber Gasket
Water Cap, to be installed only
during pump maintenance
or filter cartridge replacement
Suction Fitting, PSF-100A
or PSF-100B
Flat Washer
MANUAL DEL USUARIO
DISTRIBUIDO POR: Polygroup
®
Trading Limited
Unit 606, 6th Floor, Fairmont House, No.8 Cotton Tree Drive, Central, Hong Kong
Manual #
09C3A4USA009
BOMBA CON FILTRO DE
CARTUCHO SUMMER WAVES
®
PARA PISCINAS SOBRE SUELO
Modelos RP350/ RP400
Polygroup
®
Trading Limited, (en adelante, “Polygroup
®
”), garantiza solo al comprador original de la bomba eléctrica de tipo RP ante defectos en el material y
mano de obra durante 180 días desde la fecha de compra. El comprador original debe conservar el justificante de compra en forma de recibo de venta original
de la tienda, que deberá presentar si así se lo solicita Polygroup
®
o sus agentes delegados. Las reclama ciones de garantía no pueden procesarse sin un
justificante de compra válido. Esta garantía limitada solo se aplica al comprador original del producto y se limita a la reparación o sustitución del producto, a
discreción de Polygroup
®
. Los daños consiguientes, incluidas reclamaciones por pérdidas de agua, químicos para piscinas, daños o uso no están cubiertos por
esta garantía limitada. Esta garantía no se considerará válida en caso de modificación o reparación del producto por parte del comprador o de personas no
autorizadas, uso de e piezas o accesorios no originales de Polygroup
®
en el producto, uso del producto contraviniendo las instrucciones del fabricante, uso de
voltaje inadecuado, cualquier tipo de abuso del producto o en caso de accidente o negligencia. Esta garantía no cubre el desgaste normal, así como los casos
de fuerza mayor fuera del control de Polygroup
®
. Polygroup
®
no se hace responsable de las hierbas que pueden crecer a través del paño de tierra y / o el
revestimiento de la piscina, ya que esto no es un defecto de fabricación.
EN NINGÚN CASO SERÁN RESPONSABLES Polygroup
®
, SUS AGENTES AUTORIZADOS, ENTIDADES ASOCIADAS O EMPLEADOS ANTE EL COMPRA
DOR O TERCEROS POR DAÑOS DIRECTOS O CONSIGUIENTES. Algunos estados o países, u otras jurisdicciones, no permiten la exclusión o limitación de
daños accidentales o consiguientes, en cuyo caso no se aplicarán las anteriores limitaciones o exclusiones.
GARANTÍA LIMITADA
Si le surge algún problema con su producto Polygroup
®
, no devuelva el producto al establecimiento de compra. Las reclamaciones por garantía deben realizarse
directamente a Polygroup
®
. Antes de ponerse en contacto con el servicio de atención al cliente, revise la guía de resolución de problemas, en el manual de instalación,
o consulte las FAQ o revise los videos con las instrucciones en support.polygroupstore.com. Si continúa sin poder resolver el problema, póngase en contacto con
el servicio de atención al cliente de Polygroup
®
en el (888)919-0070. Tenga preparado el tipo de producto, el numberó de modelo y el comprobante de compra listo.
Nuestro representante del servicio de atención al cliente le ayudará a resolver el problema. Puede ser necesario que nos envíe parte del producto o el producto en su
totalidad para inspección y/o reparación. No devuelva ningún producto a Polygroup
®
sin un número de autorización de devolución.
NO DEVUELVA EL PRODUCTO A LA TIENDA
Para dudas sobre la instalación o resolución de problemas, visite
support.polygroupstore.com
Servicio de atención al cliente: (888)919-0070
Para pedir piezas y accesorios,
visite www.polygroupstore.com
LEA ESTAS INSTRUCCIONES Y CONSÉRVELAS PARA FUTURAS CONSULTAS
2
Si tuviera algún problema, llame al Servicio al cliente al número (888) 919-0070 de 8:00 a 17:00 (MST)
Lun, Jue, Vie. Días y horas ampliables durante la temporada alta.
ÍNDICE
Advertencias
Pasos Preliminares, Notas Importantes, Potencia De La Bomba Y Lista De Partes
Instrucciones De Montaje
Uso De La Bomba, Cuidado Del Motor Y Limpieza/reemplazo Del Cartucho De Filtro
Mantenimiento De La Piscina Y Cuidado Del Agua De La Piscina
Guía De Resolución De Problemas, Desmontaje Y Almacenamiento De La Bomba De La Piscina
Instrucciones De Sustitución Del Rotor Y Inspección/reemplazo Del Rotor
Información Sobre El Pedido De Piezas De Repuesto
Información Sobre La Conformidad Asme Del Accesorio De Succión
3 ~ 6
7 ~ 9
10 ~ 11
12 ~ 13
13
14
15 ~ 16
17
18
MANUAL DEL USUARIO
3
Si tuviera algún problema, llame al Servicio al cliente al número (888) 919-0070 de 8:00 a 17:00 (MST)
Lun, Jue, Vie. Días y horas ampliables durante la temporada alta.
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Al instalar y usar este equipo electrónico, deben seguirse siempre ciertas instrucciones básicas de seguridad, incluidas las siguientes:
LEA Y SIGA TODAS LAS INSTRUCCIONES
Consérvelas para futuras consultas. El incumplimiento de estas advertencias e instrucciones puede provocar lesiones graves o la muerte de los usuarios, especialmente los niños.
AVISO: LOS CLIENTES QUE ADQUIERAN PISCINAS PODRÍAN ESTAR OBLIGADOS POR LA LEGISLACIÓN ESTATAL O LOCAL A ABONAR GASTOS
ADICIONALES AL INSTALAR UNA PISCINA, EN CUMPLIMIENTO DE LAS LEYES ESTATALES O LOCALES RELATIVAS AL VALLADO Y OTROS REQUISITOS
DE SEGURIDAD. LOS CLIENTES DEBEN PONERSE EN CONTACTO CON LAS AUTORIDADES LOCALES CORRESPONDIENTES PARA MÁS INFORMACIÓN.
POLYGROUP
®
NO ES RESPONSABLE POR GASTOS ADDICIONALES QUE PUEDAN OCCURIR.
Precauciones de seguridad para los niños
1. Los niños, especialmente los menores de 5 años, tienen un alto riesgo de ahogarse. Los ahogamientos suceden de manera silenciosa y rápida, pudiendo
suceder en tan poco como 5 cm de agua.
2. Mantenga a los niños dentro de su campo de visión, permanezca cerca y vigílelos activamente cuando estén cerca o dentro de la piscina y cuando esté llenando
y vaciando la piscina.
3. Al buscar un niño perdido, compruebe primero la piscina, incluso aunque piense que el niño está en casa.
4. Sitúe las bombas y filtros de manera que los niños no puedan subirse a ellos para acceder a la piscina.
5. ADVERTENCIA: Para reducir el riesgo de lesiones, no permita a los niños utilizar este producto a menos que estén bajo estrecha supervisión en todo momento.
Vallas para piscina
Muy importante: Las vallas para piscina, que restringen el acceso a la piscina a los niños pequeños, pueden ser un requisito legal. Las vallas son necesarias para
proporcionar protección contra un posible ahogamiento o casi ahogamiento. Las vallas no sustituyen la vigilancia constante de los niños. Consulte las normas y
códigos estatales y locales antes de instalar la piscina.
Equipamiento de la piscina
1. El uso de iluminación artificial para piscinas depende del dueño de la piscina. Una vez instalada, la iluminación debe cumplir el art. 680 del Código Eléctrico
Nacional (NEC) o la última edición aprobada y debe contar con el asesoramiento de un profesional autorizado.
2. Mantenga los cables eléctricos, radios, altavoces y otros aparatos eléctricos legos de la piscina.
3. No coloque la piscina cerca o debajo de cables eléctricos.
4. Todos los componentes instalados en y/o adyacentes a una piscina sobre tierra residencial deben instalarse en conformidad con los requisitos de la última
edición publicada del NFPA 70, Código Eléctrico Nacional (NEC
®
), art. 680, Piscinas, fuentes e instalaciones similares, así como con cualquier código estatal o local.
Sensibilización con respecto a la bomba de filtración
1. ADVERTENCIA: Riesgo de descarga eléctrica. Conéctela únicamente a un receptáculo con conexión a tierra. Este producto incluye un disyuntor diferencial. En
caso de que sea necesario sustituir el enchufe o el cable, utilice únicamente piezas de repuesto que sean idénticas.
2. ADVERTENCIA: Para reducir el riesgo de descarga eléctrica, sustituya el cable dañado inmediatamente.
3. ADVERTENCIA: Para reducir el riesgo de descarga eléctrica, no utilice alargadores para enchufar la unidad en la toma de corriente; utilice una toma que esté
correctamente situada.
4. ATENCIÓN: Para reducir el riesgo de descarga eléctrica, la piscina debe colocarse a 1,8 m, como mínimo, de cualquier toma de corriente. No coloque los
aparatos móviles a menos de 1,5 m de distancia de la piscina.
ADVERTENCIA
NO SE SIENTE
NI SE TUMBE
SOBRE LA PARED
DE LA PISCINA
PUEDE SUFRIR LESIONES
PERMANENTES
ADVERTENCIA
EVITE QUEDAR ATRAPADO!
ALÉJESE DE LOS ACCESORIOS DE DRENAJE O
SUCCIÓN. EL PELO, EL CUERPO Y LAS ALHAJAS
PUEDEN SER SUCCIONADOS POR EL SYSTEMA DE
DRENADO. CORRIENDO RIESGO DE QUEDAR ATRAPADO
BAJO EL AGUA Y AHOGARSE. NO USE LA PISCINA SI LA
TAPA DEL DRENAJE O DE LA BOCA DE SUCCIÓN DE
SALIDA ESTÁ ROTA O FALTANDO .
PELIGRO
¡EVITE AHOGAMIENTOS!
VIGILE DE CERCA A LOS NIÑOS CUANDO
ESTÉN EN LA PISCINA O EN SUS ALREDEDORES.
EN EL CASO DE NIÑOS MENORES DE 5 AÑOS, EL
RIESGO DE AHOGAMIENTO ES MAYOR. VACÍE LA
ALBERCA O PREVENGA EL ACCESO A ELLA
CUANDO NO SE ENCUENTRE EN USO.
NO SE PERMITE
ZAMBULLIDAS!
AGUA POCO PROFUNDA
¡PROHIBIDO ZAMBULLIRSE DE
CLAVADO! RIESGO DE
FRACTURA DELCUELLO Y
PARÁLISIS.
Si tuviera algún problema, llame al Servicio al cliente al número (888) 919-0070 de 8:00 a 17:00 (MST)
Lun, Jue, Vie. Días y horas ampliables durante la temporada alta.
4
5. ATENCIÓN: Esta bomba ha sido diseñada para usarla únicamente con piscinas almacenables. No debe utilizarla con piscinas de instalación permanente. Una
piscina almacenable ha sido fabricada de modo que puede desmontarse fácilmente para guardarla y volver a montarse íntegramente como al principio. Una
piscina de instalación permanente se construye sobre o debajo del suelo, o de forma que no puede ser desmontada para guardarse.
6. ATENCIÓN: Para mantener la protección continua contra posibles descargas eléctricas, esta unidad debe montarse sobre una base en conformidad con las
instrucciones de instalación.
7. No entierre el cable. Coloque el cable de forma que reduzca al máximo la posibilidad de que resulte dañado por cortacéspedes, cortasetos y otros equipos.
8. La unidad incluye un disyuntor diferencial (GFCI, por sus siglas en inglés). Para probarlo, pulse el botón de prueba. El disyuntor diferencial debe interrumpir el
suministro eléctrico. Pulse el botón de reinicio (reset). El suministro debería restablecerse. Si el disyuntor diferencial no funciona de esta forma, significa que está
defectuoso. Si el disyuntor diferencial interrumpe el suministro eléctrico a la bomba sin haber pulsado el botón de prueba, significa que hay una corriente de fuga,
lo que indica que puede producirse una descarga eléctrica. No utilice esa bomba. Desconéctela y llévela a un representante de servicio cualificado para que
solucione el problema antes de usarla.
9. La Bomba de Filtro debe ser montada por un adulto; hay que tener cuidado al desembalarla y montarla, ya que puede contener bordes y puntos afilados
potencialmente peligrosos que son partes necesarias para el funcionamiento de la Bomba de Filtro.
10. No use la piscina en caso de que falte o esté rota alguna tapa de las salidas de succión o drenaje. La succión puede provocar que quede atrapada alguna parte
del cuerpo, que se enreden el cabello o las joyas o ahogamiento. Repare o cambie las tapas de las salidas de succión o drenaje antes de utilizar la piscina.
Durante el uso nocturno de la piscina, utilice iluminación artificial para iluminar todas las señales de seguridad, escaleras, escalones, cubiertas y caminos.
11. El fondo de la piscina debe ser visible en todo momento desde el perímetro exterior de la piscina.
12. Coloque una lista de números de teléfono de emergencia, como la comisaría, bomberos, ambulancias y/o unidades de rescate más cercanas. Estos números
deben mantenerse cerca del teléfono más cercano a la piscina.
13. Tenga siempre a mano un equipo básico de salvamento, que incluya uno de los siguientes:
• Una vara rígida, resistente y ligera (un cayado) con una longitud no inferior a 366 cm.
• Una cuerda de al menos 6,35 mm de diámetro con una longitud igual a la mitad de la anchura máxima de la piscina o 15,24 m, la que sea inferior, que esté
firmemente sujeta a un flotador de salvamento aprobado con un diámetro exterior de aproximadamente 38,1 cm, o un dispositivo de flotación aprobado similar.
14. La piscina debe estar situada a una distancia mínima de 1,83 m de cualquier toma de corriente, y todas las tomas de 125 V 15-20 A situadas en un radio de 6 m
de la piscina deben protegerse con un interruptor diferencial (GFCI), donde las distancias sean, por medida, la ruta más corta que seguiría el cable de
alimentación de un aparato conectado al receptáculo, sin penetrar un suelo, pared, techo, marco con puerta abisagrada o corredera, apertura de una ventana o
cualquier otra barrera permanente eficaz, hasta la pared interior de la piscina.
Sistemas de circulación
1. Los instaladores deberán seguir las instrucciones escritas relativas a la posición de todos los equipos conectados a los sistemas de circulación.
2. El instalador deberá seguir las instrucciones escritas suministradas para utilizar los componentes de los sistemas de circulación.
3. Todos los componentes y bombas del sistema de circulación que deban sustituirse o repararse deberán instalarse siguiendo el manual de instrucciones de la bomba.
4. El equipo de circulación deberá instalarse siguiendo las instrucciones del fabricante para proporcionarle un montaje y soporte adecuado, para evitar daños
derivados de una mala alineación, colocación y vibración, y para minimizar la posibilidad de acumulación de residuos y humedad. Consulte el manual de
instrucciones de la bomba.
Productos químicos
Por motivos de seguridad, asegúrese de que la parte más profunda de la piscina siempre esté visible. El usuario debe mantener siempre apropiadamente limpia el
agua de la piscina. Compruebe los niveles de pH y cloro periódicamente y asegúrese de que están dentro de los límites recomendados. De vez en cuando, podrían
ser necesarios productos químicos adicionales para tratar el agua. Lleve a analizar una muestra de agua a la tienda local de suminis tros de piscina para
determinar si necesita más productos químicos. Encienda la bomba por las horas recomendadas diariamente. Si no está seguro de los plazos, consulte
support.polygroupstore.com para las horas de funcionamiento de la bomba recomendadas, basadas en tipos y tamaños de piscina. Limpie y cambie el cartucho de
la bomba del filtro con frecuencia. Reemplazar solo con un cartucho de filtro original de la marca Polygroup
®
/ Summer Waves
®
Consulte el manual de la bomba del
filtro para más información sobre el cuidado del agua.
Riesgo de quedar atrapado
1. Evitar quedarse atrapado: No debe haber salientes u otros obstáculos en la zona de baño que puedan causar que el usuario quede atrapado o enredado. No use
la piscina en caso de que falte o esté rota alguna tapa de las salidas de succión. La succión puede provocar que quede atrapada alguna parte del cuerpo, que se
enreden el cabello o las joyas o ahogamiento. Repare o sustituya la tapa de la salida de succión antes de dejar que se use la piscina.
2. ¡PELIGRO! PARA EVITAR LESIONES GRAVES O LA MUERTE, CIERRE LA PISCINA O SPA A LOS BAÑISTAS EN CASO DE QUE FALTE O ESTÉ ROTA Y/O
INOPERATIVA ALGUNA REJILLA/TAPA DE LAS SALIDAS DE SUCCIÓN.
3. No juegue ni nade cerca de las válvulas de succión o drenaje. Podrían quedar atrapados su cabello o su cuerpo, causándole lesiones permanentes o
ahogamiento.
4. No entre a la piscina o spa en caso de que alguna válvula de succión o tapa de drenaje esté suelta, rota o falte.
5. En caso de encontrar una tapa de drenaje suelta, rota o notar que falta, notifíqueselo inmediatamente al operador o propietario de la piscina/spa.
Riesgo de ahogamiento.
1. Evite que los niños accedan a la piscina sin vigilancia instalando una valla u otra barrera aprobada alrededor de la piscina. Las leyes o códigos estatales o locales
pueden exigir una valla u otras barreras aprobadas. Consulte las normas y códigos estatales y locales antes de instalar la piscina.
2. Los juguetes, sillas, mesas y objetos similares a los que un niño podría subirse deben tener una altura mínima de 121,92 cm respecto a la piscina. El sistema del
MANUAL DEL USUARIO
5
Si tuviera algún problema, llame al Servicio al cliente al número (888) 919-0070 de 8:00 a 17:00 (MST)
Lun, Jue, Vie. Días y horas ampliables durante la temporada alta.
filtro de la bomba debe colocarse de manera que no pueda ser usado por los niños pequeños como medio de acceso a la piscina. No deje juguetes dentro de la
piscina al terminar de usarla, ya que los juguetes y objetos similares podrían atraer a los niños a la piscina.
3. Coloque los muebles (por ejemplo, mesas o sillas) lejos de la piscina para que los niños no puedan subirse a ellos para acceder a la piscina.
Riesgo de electrocución
1. Mantenga los cables eléctricos, radios, altavoces y otros aparatos eléctricos legos de la piscina.
2. No coloque la piscina cerca o debajo de cables eléctricos.
Primeros auxilios
1. Tenga siempre un teléfono en funcionamiento y una lista de número de emergencia cerca de la piscina.
2. Aprenda la técnica de la resucitación cardiopulmonar (CPR). En caso de emergencia, realizar inmediatamente la CPR puede salvar una vida.
Advertencia especial
1. Los códigos de construcción locales pueden exigir la obtención de un permiso de construcción o instalación eléctrica. El instalador debe seguir las normativas
sobre escollos, barreras, dispositivos y otros requisitos.
2. Las señales de seguridad deben cumplir los requisitos de la ANSI-Z535 y usar señalización de advertencia.
3. NO intente montar la piscina en condiciones climatológicas adversas, en caso de viento o cuando la temperatura sea inferior a 15,5 ºC.
4. La Bomba de Filtro es almacenable, por lo que debería desmontarse y guardarse cuando se esperen temperaturas por debajo de 0 ºC.
Advertencia de seguridad adicional
1. Siempre es necesaria la supervisión de un adulto.
2. Los padres deben aprender a realizar la CPR.
3. Mantenga los radios eléctricos, altavoces y otros aparatos eléctricos legos de la piscina.
4. Cuando toque el filtro, la bomba o las piezas eléctricas, asegúrese de que el suelo que pisa está totalmente seco.
5. Todas las tomas eléctricas deben tener un disyuntor diferencial y las conexiones deben estar a 1,83 m, como mínimo, del perímetro de la pared de la piscina.
A partir de 1,83 m-3,05 m, debe haber una connexion fija (caja de distribución) o una conexión de trabas giratorias con un disyuntor diferencial.
6. Conecte los cables de alimentación a una toma de corriente con conexión a tierra.
7. Mantenga todos los objetos que se puedan romper fuera de la zona de la piscina.
8. El consumo de alcohol no es compatible con las actividades de piscina. No deje que nadie nade, bucee o se deslice bajo la influencia del alcohol o las drogas.
9. Existe riesgo de descarga eléctrica si instala la bomba o el filtro en una plataforma. La bomba o el filtro podrían caer al agua, provocando descargas graves o
electrocución.
10. No instalar sobre una plataforma u otra superficie en, sobre o ligeramente por debajo del riel superior de la piscina.
11. No use la bomba de filtro durante condiciones climatológicas adversas, es decir, tormentas, tornados, etc.
12. Al aspirar la piscina o usar el mango telescópico, tenga en cuenta los cables eléctricos que pueda haber sobre usted.
13. Compruebe regularmente si existen signos de desgaste o pernos sueltos que puedan comprometer la seguridad de la plataforma.
14. Póngase en contacto con el distribuidor o fabricante de la piscina para obtener más señales de seguridad si lo considera necesario.
15. Acuda a un técnico de piscinas profesional para el servicio de mantenimiento de la piscina. Para más información entre en www.APSP.org
Folleto de sensibilización del consumidor y fuente de información
Contacto: U.S. Consumer Product Safety Commission at www.cpsc.gov/safety-education/safety-guides/pools-and-spas, Pub. #362 “Safety Barrier Guidelines for Home Pools”.
1. La manera sensata de disfrutar de su piscina sobre suelo
2. Los niños no son a prueba de agua
3. Capas de protección
4. Procedimientos de emergencias en piscinas y spas para bebés y niños
5. Existen copias gratuitas de los folletos anteriores sobre seguridad del APSP. Vaya a: www.APSP.org
Existen programas educativos y materiales
Sobre los programas educativos (es decir, seminarios, talleres, folletos, vídeos, guías) del APSP, otros grupos de seguridad acuática y empresas privadas. Con el
objetivo de comunicar información de seguridad útil a los dueños/operadores y usuarios de piscinas, está permitido que los miembros de la industria suministren esta
información a los dueños/operadores y que soliciten o exijan a los dueños/operadores una declaración firmada de que han recibido, leído y seguirán las instrucciones.
Otras fuentes de información de seguridad:
• www.cdc.gov
• www.cpsc.gov
• www.drowningpreventionalliance.com
• www.nspf.org
• www.safekids.org
ANSI American National Standards Institute
25 West 43rd Street, New York NY 10036
Contacto: 212-642-4900
www.ansi.org
6
Si tuviera algún problema, llame al Servicio al cliente al número (888) 919-0070 de 8:00 a 17:00 (MST)
Lun, Jue, Vie. Días y horas ampliables durante la temporada alta.
APSP Association of Pool & Spa Professionals
(formerly National Spa and Pool Institute)
2111 Eisenhower Avenue, Suite 500
Alexandria VA 22314-4679
Contacto: 703-838-0083
www.apsp.org
ASME American Society of Mechanical Engineers
Two Park Avenue, New York NY 10016-5990
Contacto: 800-843-2763 (U.S. & Canada) 973-882-1170 (outside North America)
www.asme.org
NSPI National Spa and Pool Institute (see APSP)
UL Underwriters Laboratories
333 Pfingsten Road, Northbrook IL 60062-2096
Contacto: 877-854-3577 or 847-272-8800
www.ul.com
NSF NSF International
P.O. Box 130140
789 N. Dixboro Road
Ann Arbor MI 48105
Contacto: 800-673-6275 or 734-769-8010
www.nsf.org
ASTM ASTM International (formerly American Society of Testing & Materials)
100 Barr Harbor Drive, P.O. BOX C700
West Conshohocken, PA 19428-2959
Contacto: 877-909-2786 (USA & Canada) or 610-832-9585 (International)
www.astm.org
NEC National Electrical Code (see NFPA)
NFPA National Fire Protection Association
1 Batterymarch Park, Quincy MA 02169-7471
Contacto: 800-344-3555 (U.S. & Canada) or 617-770-3000 (International)
www.nfpa.org
Sistemas de filtración
Hay que colocar cualquier equipo conectado a los sistemas de ventilación de manera que los niños no lo puedan usar como medio de acceso a la piscina. (Véase la
última edición publicada del Código sobre dispositivos de seguridad ANSI/APSP-8 para piscinas, spas y bañeras de hidromasaje de uso residencial).
Barrera
Las barreras son necesarias para ofrecer protección ante posibles ahogamientos y casi ahogamientos, y no son un sustituto de la supervisión constante de los niños.
(Véase la última edición publicada del Código sobre dispositivos de seguridad ANSI/APSP-8 para piscinas, spas y bañeras de hidromasaje de uso residencial).
Riesgo de accidentes de ahogamiento, atrapamiento y buceo
Hay publicaciones disponibles que describen el riesgo de accidentes de ahogamiento, atrapamiento y buceo. Las publicaciones relacionadas con la seguridad de la
piscina disponibles incluyen folletos de la Asociación de profesionales de piscina y spa (APSP) titulados: The Sensible Way to Enjoy Your Aboveground/
Onground Swimming Pool [La forma sensata de disfrutar de su piscina desmontable y fija ], Children Aren't Waterproof [Los niños no son a prueba de agua],
Pool and Spa Emergency Procedures for Infants and Children [Procedimientos de emergencia en piscinas y spas para bebés y niños], Layers of Protection [Capas
de protección], y la última edición publicada del Código sobre dispositivos de seguridad ANSI/APSP-8 para piscinas, spas y bañeras de hidromasaje de uso
residencial.
Responsabilidades del instalador
La instalación de todos estos componentes debe realizarse de manera que los niños no lo puedan usar como medio de acceso a la piscina.
(Véase el Código de Carrier sobre piscinas, spas y bañeras de hidromasaje residenciales).
GUARDE ESTAS INSTRUCCIONES
MANUAL DEL USUARIO
7
Si tuviera algún problema, llame al Servicio al cliente al número (888) 919-0070 de 8:00 a 17:00 (MST)
Lun, Jue, Vie. Días y horas ampliables durante la temporada alta.
1. El instalador deberá seguir las instrucciones suministradas por escrito sobre el funcionamiento de los sistemas de bombas de filtración.
2. Todos los componentes eléctricos deberán instalarse de acuerdo con el artículo 680 del Código Eléctrico Nacional, “Piscinas, fuentes e instalaciones similares” o
su última edición aprobada.
3. El cartucho de filtro tipo D 18 tiene capacidad para 2 de las pastillas de cloro de 2.54 cm de diámetro. Verifique sus niveles de cloro para determinar el número
correcto de pastillas de cloro que hay que agregar. El cartucho del filtro dispensa automáticamente el cloro en la piscina, mientras va funcionando la bomba de
filtración. Para usar el dispensador de cloro, necesita un tipo de cartucho del filtro que contenga un divisor de malla con un núcleo central (Ver página 9).
4. Los sistemas la bomba de filtración de la serie RP son fabricados por Polugroup
®
con el número de control de ETL 4000608 y 4006317, con doble aislamiento y
conexión a tierra, 120 VCA y 60 Hz. (Todas las unidades deben contar con 105 VCA como mínimo para empezar a funcionar correctamente).
MODELO DE BOMBA DE FILTRACIÓN
Sistema de filtración SFS350
RP400
VATAJE
20 Watts
25 Watts
AMPERAJE
0.35 Amps
0.2 Amps
LISTA DE PIEZAS
PASOS PRELIMINARES
NOTAS IMPORTANTES ACERCA DE LA BOMBA DE FILTRACIÓN
INFORMACIÓN SOBRE LA POTENCIA DE LA
BOMBA DE FILTRACIÓN
1. LEA ATENTAMENTE TODAS LAS INSTRUCCIONES y comprenda bien lo que hace falta para montar la bomba de filtración de la serie RP.
2. Se recomienda tener a mano un poco de VASELINA (no incluida) para lubricar las juntas.
ELEMENTOS NOMBRE DE PARTES
Empaque de Retorno
Accesorio de succión
Junta de succión (arandela SF)
Contratuerca de la conexión de retorno/succión
Tapadera de succión (tapón SF)
Accesorio de retorno
Desviador de la boquilla de Retorno
Tapón (uso para el servicio solamente)
Manguera
Abrazadera de la manguera
Conjunto de la bomba de filtración
A) RP350
B) RP400
Tornillo blanco
Anillo negro para el tornillo
Tapón de Sello
Empaque para la caja de filtro
CANT.
1
1
1
1
1
1
1 juego
1
2
1 juego
NOMBRE DE PARTES
Caja del filtro
Ensamblaje del motor
A) RP350
B) RP400
Cartucho filtrante tipo D
Carcasa del motor de la bomba
A) RP350
B) RP400
Ensamblaje del rotor
A) RP350
B) RP400
Voluta
Set de tornillos de la voluta (2 de cada)
Cable de alimentación IDFT (imagen solo a modo de referencia)
Salida de la bomba del filtro/Anillo negro para ajuste
Set de tornillos y arandelas del conjunto del motor (4 de cada)
ELEMENTOS
1
2
3
4
5
6
7
8
9
CANT.
2
1
1
2
1
1
1
1
2
4
1
1
1
1
1
8
Si tuviera algún problema, llame al Servicio al cliente al número (888) 919-0070 de 8:00 a 17:00 (MST)
Lun, Jue, Vie. Días y horas ampliables durante la temporada alta.
9
7
6
24
1
4
8
11
ACCESORIO DE RETORNO
2
24
1
3
4
10
ACCESORIO DE SUCCIÓN
RP350 / RP400
23
MANUAL DEL USUARIO
9
Si tuviera algún problema, llame al Servicio al cliente al número (888) 919-0070 de 8:00 a 17:00 (MST)
Lun, Jue, Vie. Días y horas ampliables durante la temporada alta.
12
13
14
15
17B
18
16
RP400
24
25
RP350
20A
19A
20B
21
22
19B
24
24
21
22
24
24
12
13
14
15
18
16
24
17 A
25
10
Si tuviera algún problema, llame al Servicio al cliente al número (888) 919-0070 de 8:00 a 17:00 (MST)
Lun, Jue, Vie. Días y horas ampliables durante la temporada alta.
1. Coloque la piscina siguiendo todas las instrucciones suministradas con la
misma. No la llene de agua hasta que haya instalado correctamente la
bomba de filtración. Coloque los orificios de entrada y salida en la pared
de la piscina.
3. Lubrique el empauqe de retorno con vaselina (no incluida) y
coloque el accesorio de retorno en el orificio de entrada de la piscina.
2. Lubrique el Empaaue de Retorno con vaselina (no incluida) e
instale el accesorio de succión en el orificio de salida de la piscina.
4. Saque la bomba de filtración , las mangueras y las abrazaderas
de las mangueras del paquete.
9
10
11
INSTRUCCIONES DE MONTAJE
ADVERTENCIA: COLOQUE ESTE PRODUCTO APARTADO DE LA PISCINA A FIN DE EVITAR QUE LOS NIÑOS SE SUBAN A ÉL Y ACCEDAN A LA PISCINA.
Antes de montar el producto, dedique unos minutos a comprobar el contenido y familiarícese con todas las piezas.
11
9
10
Orificio de
Entrada
Orificio
de Salida
7
6
1
4
4
3
1
2
Parte Fuera de
La Piscina
Parte Fuera de
La Piscina
Parte Interior de
La Piscina
Parte Interior de
La Piscina
MANUAL DEL USUARIO
11
Si tuviera algún problema, llame al Servicio al cliente al número (888) 919-0070 de 8:00 a 17:00 (MST)
Lun, Jue, Vie. Días y horas ampliables durante la temporada alta.
8. No enchufe la bomba de filtración todavía. Empiece a llenar la piscina
de agua hasta el nivel indicado.
5. Lubrique los anillos negros del accesorio de succión y la abertura de la
bomba con vaselina (no incluida). Conecte la manguera 9 al accesorio
de succión 10 a la entrada de la bomba del filtro.
6. Lubrique los anillos negros en el accesorio de retorno y en la salida de la
bomba con vaselina (no incluida). Conecte la manguera 9 del accesorio
de retorno de la piscina y el orificio de salida de la bomba de filtro.
7. Apriete todas las abrazaderas de la manguera 10 para evitar la fuga de agua.
9. Ahora hay aire atrapado en el sistema de la bomba de filtración, lo que
evitará que el agua fluya fácilmente. Para PURGAR el sistema (liberar el
aire atrapado), abra el tornillo blanco 12 que está en la parte superior
de la bomba girándolo en sentido antihorario. La presión del agua hará
salir todo el aire atrapado dentro del sistema de la bomba de filtración.
Apriete el tornillo blanco 12 cuando vea que el agua se sale por el tapón
de Sello 14 .
10. Ajuste el desviador de la boquilla de retorno 7 para maximizar la
circulación del agua de la piscina.
7
360°
4
9
10
14
12
14
12
9
10
Línea de admisión
Es necesario que el Desviador de
Retorno a punte al lado opuesto
del Skimmer.
Parte Interior
de La Piscina
12
Si tuviera algún problema, llame al Servicio al cliente al número (888) 919-0070 de 8:00 a 17:00 (MST)
Lun, Jue, Vie. Días y horas ampliables durante la temporada alta.
USO DE LA BOMBA
¡IMPORTANTE!
La bomba de filtración está protegida con un interruptor térmico. El interruptor capta la temperatura de la bomba de filtración.
Si se calienta demasiado, el interruptor parará el funcionamiento de la bomba hasta que se enfríe. Una vez se haya enfriado, la bomba de filtración
volverá a funcionar automáticamente. Se trata de un dispositivo de seguridad que sirve para evitar que la bomba se dañe y ampliar su vida útil. Si la
bomba se apaga automáticamente, es porque la temperatura del agua de la piscina es elevada y/o porque el flujo de agua que pasa por la bomba
es escaso. Si esto ocurre, tiene que comprobar el flujo de agua y corregirlo si es necesario, ya que esta bomba de filtración utiliza el flujo de agua
para enfriarse. Si quiere, también puede poner en funcionamiento la bomba durante la noche, cuando la temperatura es más baja.
CUIDADOS DEL MOTOR DE LA BOMBA
1. Enchufe el set de cable de alimentación GFCI 23 a un tomacorriente correctamente puesto a tierra al menos a 15 pies
(4.5 m) de la piscina.
2. Para encender la Bomba, presione el botón RESET del enchufe GFCI.
3. Desde dentro de la piscina, verifique si el flujo de agua desde el Desviador de la boquilla de Retorno 7 está correcto.
Debe sentirse como un flujo sólido de agua que retorna a la piscina. Si no, o si siente reducción de flujo, limpie o reemplace
el Cartucho de filtro 18 Para detalles, vea USO Y CUIDADO DEL CARTUCHO DE FILTRO a continuación, así como el
Problema 2 de la GUÍA E RESOLUCIÓN DE PROBLEMAS (p. 14).
4. Para apagar la Bomba, presione el botón de PRUEBA del enchufe del IDTF y desenchúfelo
de la salida de la alimentación.
5. MUY IMPORTANTE: Verifique y ajuste los niveles de cloro y de pH todos los días.
LA BOMBA DEL FILTRO POR SÍ MISMA NO EVITARÁ QUE CREZCAN ALGAS
EN EL AGUA DE LA PISCINA; ESTO SOLO PUEDE HACERSE MANTENIENDO
NIVELES ADECUADOS DE CLORO Y DE pH EN TODO MOMENTO. Para detalles,
vea CUIDADO DEL AGUA DE LA PISCINA (p. 13).
2. Para despresurizar el sistema de la bomba de filtración, púrguela girando
el tornillo blanco 12 en sentido antihorario.
3. Utilice las dos manos para girar el tapón de Sello 14 en sentido antihorario.
Retire el cartucho filtrante 18 .
5. Cuando haya terminado de limpiar el cartucho filtrante, lubrique genero
samente el empaque 15 con vaselina y vuelva a montarlo siguiendo el
orden inverso. Antes de reiniciar la bomba del filtro, asegúrese de retirar
el TAPÓN RF 8 y la TAPA SF 5 .
14
18
LIMPIEZA Y SUSTITUCIÓN DEL CARTUCHO FILTRANTE
5
2
8
7
6
14
12
14
12
Parte Interior
de La Piscina
4. Los escombros y los restos de suciedad más toscos en el filtro de
cartucho pueden limpiarse mediante el lavado a presión del interior y
exterior con una manguera de jardín, asegurándose de lavar todos los
pliegues. Deje que el filtro se seque durante varias horas y CEPILLE
CUIDADOSAMENTE los pliegues para no dañar el filtro de cartucho.
NO frote las superficies plisadas. Limpiar y frotar un filtro vigorosa
mente desgastará el cartucho mucho más deprisa que si es enjuagado
adecuadamente con la manguera.
1. Desenchufe la bomba de filtración. Quite el desviador RF 7 del accesorio de
retorno 6 y enchufe la tapadera de succiónel RF 8 . Apriete manualmente
el tapón SF 5 en el accesorio de succión 2 .
IMPORTANTE: ¡NO conecte el conjunto
a un dispositivo temporizador!
Pulse
el botón
"RESET"
para
arrancar
la bomba
Cómo utilizar el tapón del GFCI
*No conectar a
un temporizador
23
MANUAL DEL USUARIO
13
Si tuviera algún problema, llame al Servicio al cliente al número (888) 919-0070 de 8:00 a 17:00 (MST)
Lun, Jue, Vie. Días y horas ampliables durante la temporada alta.
MANTENIMIENTO DE LA PISCINA
6. Los aceites bronceadores y corporales y las algas forman una capa sobre los pliegues del filtro que quizás no pueda eliminar con la manguera. Estas películas de
aceite y/o algas atascarán rápidamente los poros del filtro, reduciendo en gran medida la filtración. De modo que debe eliminar dicho material del filtro lo antes
posible. Para eliminar el aceite, le recomendamos empapar el cartucho en una solución de 454 g de fosfato sódico (o cualquier otro detergente fuerte) en 5 galones
(19 l) de agua durante 12 horas como máximo. El fosfato sódico está disponible en muchos supermercados, ferreterías o tiendas de suministros de limpieza. Una
vez eliminado el aceite, enjuague el cartucho filtrante para eliminar cualquier suciedad. Si las algas son un problema, añada ½ pinta de cloro o 1 pinta de lejía líquida
doméstica a la solución limpiadora 1 hora antes de sacar el cartucho filtrante de la solución. Enjuague bien el cartucho filtrante antes de volver a colocarlo dentro
de la carcasa. Compruebe la química de la piscina para determinar la causa del crecimiento de algas.
7. El cartucho filtrante puede acumular depósitos de cal y/o minerales en exceso, en este caso, el tratamiento debe ser diferente. Póngase en contacto con su
proveedor local de suministros para piscinas para que le informe sobre otros tipos limpiadores de cartuchos o tratamientos para los depósitos de cal o minerales.
Compruebe la química de la piscina para ver si el pH o la alcalinidad son elevados; esto puede provocar depósitos de cal o minerales.
8. Un cartucho filtrante de repuesto en reserva 18 es una inversión excelente. Proporciona un modo cómodo de seguir filtrando su piscina durante la limpieza o
sustitución de un cartucho de filtro 18 sucio. Además, un cartucho limpio y con un buen mantenimiento le asegura que el filtro siempre estará listo para funcionar
con la máxima eficacia.
9. Puede comprar los cartuchos filtrantes en la tienda donde compró la piscina o pedirlos a Polygroup
®
en polygroupstore.com. Sustitúyalos siempre por
auténticos cartuchos filtrantes SUMMER WAVES
®
de Polygroup
®
.
Pastillas de cloro
1. Compruebe y ajuste cada día los niveles de pH y cloro utilizando los productos químicos adecuados. Consulte la sección “TRATAMIENTO DEL AGUA DE LA PISCINA”.
2. Compruebe la salida de la bomba filtrante a diario. Si el flujo se reduce, consulte el síntoma 2 en la sección “GUÍA DE RESOLUCIÓN DE PROBLEMAS”.
3. Compruebe si hay alguna fuga en la bomba filtrante, las mangueras y los accesorios. Si encuentra una fuga, consulte el síntoma 4 en la sección “GUÍA DE
RESOLUCIÓN DE PROBLEMAS”.
4. Prenda el motor/bomba en las hora recomendables diariamente. Si está inseguro del tiempor requerido por favor ahaga referencia a support.polygroupstore.com
para las “Horas de Operación para su Motor”, que basa en los tipos de piscinas y tamaños.
1. Los siguientes artículos son necesarios y puede encontrarlos en su tienda local de suministros para piscinas:
Test Kit - Used to check chlorine and pH levels.
1” Chlorine Tablets - Used to disinfect pool water and help control the growth of algae.
pH Control Chemicals - Used to adjust pH levels Up (Soda Ash) or Down (Acid).
Algaecides - Used to eliminate algae.
Superchlorinator - Used to destroy combined chlorine, ammonia, nitrogen, and organic compounds.
Red Para Hojas con mango. Se utiliza para quitar hojas, suciedad, insectos, etc. de la piscina. Este producto puede ser
comprado en polygroupstore.com.
Chlorine Dispenser (Supplied with Polygroup
®
’s patented Filter Cartridge U.S. Pat. 7,005,062) - Used to dispense 1”
chlorine tablets ONLY.
2. Utilice el kit de prueba cada día para comprobar los niveles de pH y cloro. Ajuste según corresponda utilizando los
productos químicos adecuados.
NOTA: Un nivel excesivo de cloro o un nivel muy bajo de pH dañarán el revestimiento de la piscina.
3. Se puede limpiar la piscina con una manguera de aspiración de jardín de Polygroup
®
o comprarla en una tienda de
suministros para piscina.
4. Utilizar un pediluvio cerca de la piscina para lavarse los pies antes de entrar ayudará a mantener la piscina limpia.
5. El agua de pozo suele presentar problemas especiales con la química del agua. Si tiene que usar agua de pozo, lleve una muestra a su proveedor local de
productos químicos para piscinas para análisis para que añada CUALQUIER sustancia química.
6. Consulte el MANUAL DE INSTRUCCIONES DE LA PISCINA para saber su capacidad. Necesitará esa información para determinar la cantidad de producto químico
que es necesario para corregir el agua de su piscina. NOTA: Se recomienda utilizar un cubo de agua de 19 litros para mezclar y disolver los productos
químicos y, luego, aplicarlos directamente al agua de la piscina. Seguir directamente las instrucciones de la etiqueta del fabricante. *La mayoría de las tiendas de
suministros para piscinas le harán una prueba del agua de su piscina gratuitamente y le aconsejarán sobre qué productos químicos debe utilizar para su piscina.
Tendrá que decirles la capacidad de la piscina en galones.
7. IMPORTANTE. No podemos darle excesiva importancia al tratamiento químico adecuado diario. Los niveles de cloro y pH deben mantenerse adecuadamente de
forma puntual. LA BOMBA Y EL FILTRO POR SÍ MISMOS NO EVITARÁN LA APARICIÓN DE ALGAS EN EL AGUA DE LA PISCINA; ESTO SOLO PUEDE
EVITARSE MANTENIENDO EL NIVEL ADECUADO DE CLORO Y pH EN TODO MOMENTO.
• Mantenga el nivel de pH entre 7.3 y 7.8.
• Mantenga el nivel de cloro entre 1.0 y 1.6 ppm (partes por millón).
• Debe superclorinar su piscina al menos una vez cada dos semanas.
NOTA:
1. El clima cálido/uso intensivo pueden requerir unos niveles de pH y cloro situados en la parte alta de la escala y el superclorinado de la piscina cada semana.
2. Utilizar una cubierta de piscina y/o una cubierta térmica ayudará a mantener los niveles de pH y cloro reduciendo la cantidad de evaporación de la piscina.
CUIDADO. El nivel de cloro concentrado y el nivel de pH dañarán la piscina. Debe seguir las instrucciones de cantidad y uso recomendado de los productos químicos
que utiliza para la piscina. NUNCA deje caer terrones o comprimidos de productos químicos en la piscina; esto puede suponer un riesgo para los nadadores y/o
dañar el recubrimiento de la piscina.
CUIDADO DEL AGUA DE LA PISCINA
14
Si tuviera algún problema, llame al Servicio al cliente al número (888) 919-0070 de 8:00 a 17:00 (MST)
Lun, Jue, Vie. Días y horas ampliables durante la temporada alta.
1
2
3
4
SÍNTOMA CAUSA SOLUCIÓN
El motor no
arranca o arranca
y se apaga
A La unidad debe enchufarse a una toma de corriente de 3 conductores y toma de tierra.
Pulse el botón de reinicio en el IDTF para encender la bomba.
B Reinicie el enchufe del disyuntor y/o el cortocircuito. Si el problema continúa, lleve el
circuito a un electricista cualificado para que lo revise.
C Compruebe que la tensión suministrada sea de 105 a 125 V (CA).
El agua no fluye,
o fluye muy despacio,
por la manguera
de retorno.
La Bomba de
filtración no está
limpiando la piscina
correctamente
(p. ej. agua
turbia/verde)
Fuga de agua
A Llene la piscina hasta la línea. El accesorio de succión debe estar como mínimo 4”
(10,16 cm) por debajo del agua.
A Mantenga el nivel de cloro entre 1.0 y 1.6 ppm.
B Mantenga el nivel de pH entre 7.3 y 7.8.
C Limpie o reemplace el filtro de cartucho (consulte la página 12). Un cartucho de repuesto hace
más cómoda su reparación.
A Asegúrese de que la abrazadera de la manguera 10 esté bien posicionada sobre la manguera
y la junta tórica 24 para garantizar una buena estanqueidad. Ajuste la abrazadera de la
manguera, compruebe la junta tórica y vuelva a apretarla. Compruebe la manguera en busca
de agujeros o fisuras, y reemplácela de ser necesario.
D Inspeccione el cartucho de filtración en busca de agujeros o desgarres. Reemplace el filtro de
cartucho si se observan daños.
E Compruebe que no haya obstrucciones en la conexión o la manguera de succión ni en la
conexión o manguera de retorno.
F Lleve el agua de la piscina a una tienda de suministros para piscina para que le hagan una
prueba. Busque opiniones acerca de otros productos químicos de tratamiento de agua.
G Encienda la bomba más a menudo, pero nunca cuando esté en uso. Limpie/sustituya el
cartucho filtrante más a menudo.
B Compruebe que no haya obstrucciones en la conexión o la manguera de succión ni en la
conexión o manguera de retorno.
A La unidad no está enchufada
o el disyuntor diferencial no
está activado
B El tapón del disyuntor
diferencial y/o el cortocircuito
se ha desconectado
C Voltaje bajo
A El nivel del agua de la
piscina es bajo
A Los niveles de cloro no se encuentran
en el intervalo apropiado.
B El nivel de pH no está en el intervalo
apropiado.
C El cartucho filtrante está sucio
D
El cartucho filtrante está dañado
E Flujo de agua lento
F Hacen falta otros productos
químicos
G El agua de la piscina está
muy sucia
B Orificio de entrada/salida
atascado
C El cartucho filtrante está sucio
A Área de la manguera: La manguera
de succión o retorno no se acopla
bien a las conexiones del portafiltro
y/o las conexiones de la pared.
B Tornillo de purga del tapón
de cierre
C Tapón de cierre
C Limpie o reemplace el filtro de cartucho (consulte la página 12). Un cartucho de repuesto hace
más cómoda su reparación.
B Compruebe si la junta tórica 13 está dañada. Sustituir si es necesario. Apriete el tornillo
de la válvula de purga 12 .
C Compruebe si la junta tórica 15 está dañada. Sustituir si es necesario. Apriete la parte
superior del cierre 1 .
GUÍA DE RESOLUCIÓN DE PROBLEMAS
ADVERTENCIA: DESENCHUFE EL CABLE DE ALIMENTACIÓN ANTES DE SOLUCIONAR CUALQUIER PROBLEMA EN LA BOMBA DE FILTRACIÓN.
DESMONTAJE Y ALMACENAMIENTO DE LA BOMBA DE LA PISCINA
1. Apague primero la bomba y desenchufe el cable de alimentación del sistema. Quite el distribuidor RF 7 del accesorio de retorno 6 y, a continuación, enchufe el
accesorio de retorno 6 con el tapón RF 8 . Ahora, apriete manualmente el tapón SF 5 situado en el accesorio de succión 2 .
2. Lentamente, destornille el Tornillo blanco 12 del Tapón de Sello 14 para despresurizar la bomba.
3. Quite el Tapón de Sello 14 girándolo en sentido antihorario.
4. Quite el cartucho filtrante 18 y saque las pastillas de cloro que estén en el interior del filtro.
5. Aloje las cuatro abrazaderas de las mangueras 10 , saque las mangueras 9 y deje que el agua se drene.
6. Limpie y seque todas las piezas de la bomba filtrante, incluidos los cartuchos filtrantes.
7. Lubrique abundantemente el anillo negro 13 y el Empaque 15 con vaselina, y luego vuelva a ensamblarlo, junto con el Tapón de sello 14 y el Tornillo de purga 12 ,
en la Caja 16 . Guarde todas las partes cuidadosamente en una bolsa de plástico hermética.
8. Almacene todas las partes en un ambiente seco que permanezca por encima de los 0 °C (32 °F) en todo momento.
MANUAL DEL USUARIO
15
Si tuviera algún problema, llame al Servicio al cliente al número (888) 919-0070 de 8:00 a 17:00 (MST)
Lun, Jue, Vie. Días y horas ampliables durante la temporada alta.
1. Apague primero la bomba y desenchufe el cable de alimentación del sistema. Quite el distribuidor RF 7 del accesorio de retorno 6 y, a continuación, enchufe el
accesorio de retorno 6 con el tapón RF 8 . Apriete manualmente el tapón SF 5 situado en el accesorio de succión 2 .
2. Lentamente, destornille el Tornillo blanco 12 del Tapón de Sello 14 para despresurizar la bomba.
3. Afloje las abrazaderas de la manguera 10 en la entrada y salida de la bomba del filtro. Suelte ambas mangueras 9 de la bomba del filtro.
4. Ponga la bomba del filtro boca abajo. Retire el juego de tornillo y arandela del motor 25 .
(ACUÉRDESE DE GUARDAR TODAS LAS PIEZAS EN UN LUGAR SEGURO PARA SU MONTAJE POSTERIOR).
1. Para reemplazar el motor 20 , quite los tornillos 22 de la voluta. Agarre la carcasa del motor con una mano y la boca de descarga de la voluta con la otra. Gire
la boca de descarga en sentido antihorario para liberar los resaltes de la voluta de los ganchos de la bomba.
2. Tire con cuidado hacia arriba para separar los resaltes de los ganchos.
3. Quite la voluta 21 y tire hacia fuera del rotor 20 para sacarlo de la carcasa del motor 19 . Tenga cuidado, dado que el conjunto del rotor está constituido de
varias piezas que podrían separarse unas de otras.
4. Inspeccione el conjunto del rotor y asegúrese de que no le falte ninguna pieza y de que la columna central, el eje magnético o las aspas no estén rotos, dado que
podrían causar fallos en la bomba. Si el conjunto del rotor está roto, puede adquirir otro en polygroupstore.com sin tener que reemplazar toda la bomba.
INSTRUCCIONES DE SUSTITUCIÓN DEL ROTOR
INSPECCIÓN DEL ROTOR E INSTRUCCIONES DE REEMPLAZO
16
16
17
17
25
(ACUÉRDESE DE GUARDAR TODAS LAS PIEZAS EN UN LUGAR SEGURO PARA SU MONTAJE POSTERIOR).
5. Retire el motor 17 del portafiltros 16 .
16
Si tuviera algún problema, llame al Servicio al cliente al número (888) 919-0070 de 8:00 a 17:00 (MST)
Lun, Jue, Vie. Días y horas ampliables durante la temporada alta.
5. Consulte acerca de los sistemas de filtración RP350/RP400 en la sección “Soporte técnico para piscinas - Resolución de problemas de los sistemas de filtración” en
la página web support.polygroupstore.com.
AVISO: Aunque el conjunto del rotor esté en perfectas condiciones, si no está bien colocado entre la voluta y la bomba, no funcionará correctamente.
6. Cómo reensamblar la bomba (conjunto del motor): Inserte con cuidador el conjunto del rotor 20 en el cuerpo del motor de la bomba 19 . El imán atraerá el conjunto
del rotor hacia el interior de la bomba. Asegúrese de que el conjunto del rotor esté completamente ensamblado y alineado correctamente en el interior de la bomba.
7. Una vez insertado el rotor, asegure de nuevo los resaltes de la voluta a los ganchos de la bomba girando la boca de descarga de la voluta en sentido horario.
8. Apriete la voluta 21 con los tornillos 22 correspondientes para completar el ensamblaje de la bomba (conjunto del motor).
9. Introduzca poco a poco el conjunto del motor 17 en el portafiltro 16 y asegure el conjunto del motor 17 con el set de tornillos y arandelas 25 correspondiente.
19
20
21
22
Voluta Tubos de
descarga de la boquilla
Deslice las lengüetas de la carcasa de la
voluta por debajo de las abrazaderas del
Cuerpo de la bomba para bloquear
Eje del rotor
(Este eje debe debe
atravesar todas las partes
e ingresar a las dos tapas
del extremo del eje)
Los soportes de
la cuerpo de la
bomba.
Ensamblaje del Rotor
Tapón del Asta
Arandela
Paletas del Impulsor
Eje Magnetico
Arandela
Tapón del Asta
Cuerpo de la bomba
Tornillos de la carcasa
de la voluta
MANUAL DEL USUARIO
17
Si tuviera algún problema, llame al Servicio al cliente al número (888) 919-0070 de 8:00 a 17:00 (MST)
Lun, Jue, Vie. Días y horas ampliables durante la temporada alta.
CLAVE DESCRIPCIÓN
RP400RP350
N.º DE PIEZA
1
2
3
4
5
6
7
8
9
10
12
13
14
15
16
17
18
20
21
22
24
*
*
*
Junta para racor
Accesorio de succión
Arandela del accesorio de succión (arandela SF)
Contratuerca de la conexión de retorno/succión
Tapadera de succión (tapón SF)
Accesorio de retorno
Distribuidor del accesorio de retorno (distribuidor RF)
Tapón del accesorio de retorno (tapón RF)
Manguera
Abrazadera de la manguera
Tornillo de purga
Junta tórica del tornillo de purga
Tapón de cierre
Junta del cartucho
Caja de la bomba del filtro
Conjunto del motor
Cartucho filtrante tipo D
Conjunto del rotor
Voluta
Juego de tornillos de la tapa de la voluta
Salida de la bomba del filtro / Junta tórica de ajuste
Manguera de 1,50 m
Adaptador de válvula de goma de 1-1/4” a 1-1/2”
Se vende por separado para las bombas de filtro de la serie RP
P58PF1520K01
P58281283W05
P58PF1510K01
P58PF1430W05
P58PF2820P01
P58PF7800W05
P58PF7790W05
P58PF0620K01
P58125036W01
P58220221W05
P58534000W05
P58031000K01
P58PF5290W05
P58096000K01
P58530000W05
P53F0350C000
P581041037PR
P58050350001
P58PF5270K01
P5816300270B
P58030001K01
P584150006W1
P58PF5620P01
P53FR0350W05
P58PF1520K01
P58281283W05
P58PF1510K01
P58PF1430W05
P58PF2820P01
P58PF7800W05
P58PF7790W05
P58PF0620K01
P58125036W01
P58220221W05
P58534000W05
P58031000K01
P58PF5290W05
P58096000K01
P58530000W05
P58F0400C000
P581041037PR
P58050400001
P58PF5270K01
P5816300270B
P58030001K01
P584150006W1
P58PF5620P01
P53FR0400W05
INFORMACIÓN SOBRE EL PEDIDO DE PIEZAS DE REPUESTO
MANUAL DEL USUARIO
18
Si tuviera algún problema, llame al Servicio al cliente al número (888) 919-0070 de 8:00 a 17:00 (MST)
Lun, Jue, Vie. Días y horas ampliables durante la temporada alta.
9. El orificio de salida de succión PSF-100A o PSF-100B debe sustituirse cada 5 años.
10. No es necesario utilizar herramientas para la instalación.
11. Instrucciones de mantenimiento y acondicionamiento para el invierno:
a. ¡ATENCIÓN! NO SUPERE EL CAUDAL MÁXIMO PERMITIDO: 24 galones por minuto (1440 galones o 5451 l por hora).
b. Observe e inspeccione con atención el orificio de salida de succión para ver si está dañado o alterado cada vez que vaya a utilizar la piscina. Los orificios de
salida de succión perdidos, rotos o agrietados deben sustituirse antes de utilizar la piscina.
c. Si el accesorio de succión está suelto hay que volver a conectarlo o sustituirlo antes de utilizar la piscina.
d. Retire y guarde el conjunto del orificio de salida de succión si la temperatura baja a menos de 0 ºC (32 °F).
1. Los orificios de salida de succión PSF-100A y PSF-100B tienen la certificación de la IAPMO de acuerdo con la norma ASME/ANSI/APSP/ICC-16 2011 Accesorio
de succión para piscinas, piscinas infantiles, spas y bañeras de hidromasaje.
2. Se trata de un orificio de salida de succión sumergido que se utiliza en piscinas por encima del nivel del suelo.
3. Solo para drenaje individual. Utilice solo UN orificio de salida en cada bomba.
4. No coloque este orificio de salida de succión en zonas para sentarse o en el respaldo de dicha zona.
5. Instale este orificio de salida en el lugar recomendado por el fabricante de la piscina. Altura máxima 1.8 m desde el suelo.
6. El caudal máximo permitido de este orificio de salida de succión es de 24 galones por minuto (1440 galones o 5451 litros por hora).
7. Manguera de conexión:
a. El modelo PSF-100-A debe conectarse a una manguera con un diámetro de 1 ¼” (31,8 mm).
b. El modelo PSF-100-B debe conectarse a una manguera con un diámetro de 1 ½” (38,1 mm).
8. El orificio de salida de succión debe montarse en la abertura especificada por el fabricante de la piscina situada por encima del nivel del suelo. El diámetro de
esta abertura deberá ser de entre 1,77” y 1,85” (entre 45 mm y 47 mm). Consulte en el siguiente diagrama las instrucciones de montaje detalladas:
PSF-100A y PSF-100B Orificio De Salida De Succión (Para Piscinas Sobre Suelo)
Piscina
Manguera
Abrazadera de la manguera
Contratuerca, debe apretarse a mano
Junta de goma
Tapón de agua, solo debe
instalarse mientras se lleva a cabo
el mantenimiento de la bomba
Accesorio de succión,
PSF-100A o PSF-100B
Arandela plana
INFORMACIÓN SOBRE LA CONFORMIDAD ASME DEL
ACCESORIO DE SUCCIÓN
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Summer Waves P1000830A156 Guía de instalación

Categoría
Accesorios para piscinas elevadas
Tipo
Guía de instalación