Yamaha YHT-S300 El manual del propietario

Categoría
Receptor
Tipo
El manual del propietario
Home Theater Package
(Subwoofer Integrated Receiver + Speaker)
YHT-S300
(SR-300 + NS-B380)
Owner’s Manual
English
2 En
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install this unit in a well ventilated, cool, dry, clean
place - away from direct sunlight, heat sources,
vibration, dust, moisture, and/or cold. For proper
ventilation, allow the following minimum clearances.
Top: 5 cm (2 in)
Rear: 5 cm (2 in)
Sides: 5 cm (2 in)
3 Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes
from cold to hot, and do not locate this unit in an
environment with high humidity (i.e. a room with a
humidifier) to prevent condensation inside this unit,
which may cause an electrical shock, fire, damage to
this unit, and/or personal injury.
5 Avoid installing this unit where foreign objects may fall
onto this unit and/or this unit may be exposed to liquid
dripping or splashing. On the top of this unit, do not
place:
Other components, as they may cause damage and/or discoloration
on the surface of this unit.
Burning objects (i.e. candles), as they may cause fire, damage to
this unit, and/or personal injury.
Containers with liquid in them, as they may fall and liquid may
cause electrical shock to the user and/or damage to this unit.
6 Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If the
temperature inside this unit rises, it may cause fire,
damage to this unit, and/or personal injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall
outlet, grasp the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using
this unit with a higher voltage than specified is
dangerous and may cause fire, damage to this unit, and/
or personal injury. Yamaha will not be held responsible
for any damage resulting from use of this unit with a
voltage other than specified.
13 To prevent damage by lightning, keep the power cable
and outdoor antennas disconnected from a wall outlet or
the unit during a lightning storm.
14 Do not attempt to modify or fix this unit. Contact
qualified Yamaha service personnel when any service is
needed. The cabinet should never be opened for any
reasons.
15 When not planning to use this unit for long periods of
time (i.e. vacation), disconnect the AC power plug from
the wall outlet.
16 Be sure to read the “Troubleshooting” section on
common operating errors before concluding that this
unit is faulty.
17 Before moving this unit, press to set this unit in
standby mode, and disconnect the power supply cable
from the wall outlet.
18 Condensation will form when the surrounding
temperature changes suddenly. Disconnect the power
supply cable from the outlet, then leave the unit alone.
19 Install this unit near the wall outlet and where the AC
power plug can be reached easily.
20 The batteries shall not be exposed to excessive heat such
as sunshine, fire or like.
21 Secure placement or installation is the owner’s
responsibility. Yamaha shall not be liable for any
accident caused by improper placement or installation of
speakers.
For U.K. customers
If the socket outlets in the home are not suitable for
the plug supplied with this appliance, it should be cut
off and an appropriate 3 pin plug fitted. For details,
refer to the instructions described below.
The plug severed from the mains lead must be destroyed, as
a plug with bared flexible cord is hazardous if engaged in a
live socket outlet.
Special Instructions for U.K. Model
Caution: Read this before operating your unit.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
As long as this unit is connected to the AC wall
outlet, it is not disconnected from the AC power
source even if you turn off this unit by . In this
state, this unit is designed to consume a very small
quantity of power.
Note
IMPORTANT
THE WIRES IN THE MAINS LEAD ARE
COLOURED IN ACCORDANCE WITH THE
FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:
The wire which is coloured BLUE must be
connected to the terminal which is marked with the
letter N or coloured BLACK. The wire which is
coloured BROWN must be connected to the
terminal which is marked with the letter L or
coloured RED.
Making sure that neither core is connected to the
earth terminal of the three pin plug.
INTRODUCTION PREPARATION
BASIC
OPERATION
USEFUL
OPERATION
ADDITIONAL
INFORMATION
3 En
INTRODUCTION
Getting started....................................................4
Supplied parts........................................................ 4
Controls and functions ..........................................5
PREPARATION
Placing .................................................................8
Placing the speakers.............................................. 8
Connection ........................................................10
Overview............................................................. 10
Connecting a TV ................................................. 11
Connecting Blu-ray disc player or
set-top box ....................................................... 11
BASIC OPERATION
Basic playback operation.................................12
Enjoying sound modes .....................................13
Surround mode.................................................... 13
Stereo mode ........................................................ 13
UniVolume™...................................................... 13
Listening to FM broadcasts.............................14
Basic tuning operation ........................................ 14
Editing the preset FM station .............................. 14
Using optional equipment................................16
Connecting dock ................................................. 16
Using iPod™....................................................... 16
Using Bluetooth™ components .......................... 17
USEFUL OPERATION
Setup menu ....................................................... 18
Overview .............................................................18
Basic procedure...................................................18
Adjusting the volume balance during
playback...........................................................19
Adjusting high/low frequency sound
(tone control)....................................................19
Adjusting the audio delay....................................19
Setting the audio output ......................................19
Switching on/off the HDMI™ control
function ............................................................19
Changing the brightness of the front panel
display..............................................................20
Changing the setting of the speaker type ............20
Setting the distance between the speakers ..........20
Using the HDMI™ control function ...................21
ADDITIONAL INFORMATION
Additional information.................................... 22
Troubleshooting ..................................................22
Glossary...............................................................25
Specifications ......................................................27
Available signal information...............................28
Contents
About this manual
In this manual, operations that can be performed using either the front panel buttons or the remote control are
explained using the remote control.
y indicates a tip for your operation. Notes contain important information about safety and operating
instructions.
This manual is produced prior to production. Design and specifications are subject to change in part as a result
of improvements, etc. In case of differences between the manual and the product, the product has priority.
4 En
INTRODUCTION
This product consists of the following items. Before making connections, make sure you have received all of the
following items.
Units
Accessories
Installing the batteries
Getting started
Supplied parts
Subwoofer Integrated Receiver (SR-300) Speakers (NS-B380)
Speaker cable (3 m × 2) Remote control Indoor FM antenna
(Asia model) (Europe and Russia
models)
Stand × 2
(for speaker)
Battery × 2 (AAA, R03, UM4) Screw × 2
(for stand)
CD-ROM
(Owner’s Manual)
Quick Reference
Guide
If the effective operation distance of the remote control decreases considerably, replace
the batteries with two new ones as soon as possible.
Do not use an old battery together with new one.
• Do not use different types of batteries (for example, alkaline and manganese) together.
Their performance will vary, even if they are similar in shape.
If the batteries run out, immediately remove them from the remote control to prevent an
explosion or acid leak.
Dispose of batteries according to regional regulations.
If a battery starts leaking, dispose of it immediately. Be careful not to let leaking battery
acid come into contact with your skin or clothing. Before inserting new batteries, wipe
the compartment clean.
Notes
5 En
Getting started
INTRODUCTION
Front panel of the subwoofer integrated receiver
1
Turns on the system, or sets it to standby mode.
( P. 12)
A small amount of electricity is consumed to receive
the infrared signal from the remote control even when
the system is in standby mode.
2 STATUS indicator
Lights up to show the system condition. ( P. 12)
3 INPUT
Selects an input source you want to listen to.
( P. 12)
4 VOLUME –/+
Controls the volume of the system. ( P. 12)
5 Remote control sensor
Receives infrared signals from the remote control.
( P. 7, 10)
6 Front panel display
Shows information about the operational status of
the system. ( P. 12)
Rear panel of the subwoofer integrated receiver
1 Power Cable
For connecting an AC wall outlet. ( P. 10)
2 HDMI IN 1 - 3/HDMI OUT
HDMI IN 1 - 3 for connecting HDMI
compatible external components. ( P. 11)
HDMI OUT for connecting an HDMI
compatible TV. ( P. 11)
3 DIGITAL IN jack
For connecting optical digital cable to the TV.
( P. 11)
4 ANALOG INPUT jack
For connecting analog audio cable to external
components. ( P. 10)
5 DOCK terminal
For connecting an optional Yamaha iPod universal
dock (such as YDS-11, sold separately) or
Bluetooth wireless audio receiver (such as YBA-
10, sold separately). ( P. 16)
6 ANTENNA terminal
For connecting supplied FM antenna. ( P. 10)
7 SPEAKERS terminal
For connecting speakers. ( P. 10)
Controls and functions
1 2 3 4 5 6
Note
1 2
7 6 5 4 3
Getting started
6 En
Front panel display of the subwoofer integrated receiver
1 HDMI indicator
Lights up during normal communication when
HDMI is selected as an input source.
2 Tuner indicators
TUNED indicator
Lights up when the system is receiving a station.
( P. 14)
STEREO indicator
Lights up when the system is receiving a strong
signal from an FM stereo broadcast station in
automatic tuning mode. ( P. 14)
AUTO indicator
Flashes when the system is tuning station
automatically. ( P. 14)
MEMORY indicator
Flashes when the system is storing a station.
( P. 14, 15)
EMPTY indicator
Lights up when the storing preset number is empty.
( P. 15)
PS/PTY/RT/CT indicator (Europe and
Russia models only)
Lights up according to the available Radio Data
System information. ( P. 15)
3 Decoder indicators
The respective indicator lights up when any of the
decoders of the system is activated.
4 DOCK indicator
Lights up when the system is receiving a signal
from an iPod stationed in the Yamaha iPod
universal dock (such as YDS-11, sold
separately) connected to the DOCK terminal of
the subwoofer integrated receiver. ( P. 16)
Lights up while the Yamaha Bluetooth wireless
audio receiver (such as YBA-10, sold
separately) is connected to the Bluetooth
component. ( P. 17)
Flashes while the connected Yamaha Bluetooth
wireless audio receiver (such as YBA-10, sold
separately) and the Bluetooth component are
pairing ( P. 17) or while the Yamaha
Bluetooth wireless audio receiver is searching
for the Bluetooth component. ( P. 17)
5 VOLUME indicator
Indicates the current volume level.
Flashes while the mute function is activated.
( P. 12)
6 Multi information display
Shows the selected input source, current sound
mode and other information.
7 ENHANCER indicator
Lights up when compressed music enhancer
function is activated. ( P. 16)
8 UNIVOLUME indicator
Lights up when UniVolume mode is selected.
( P. 13)
1 2 3 4
5
8
7
6
7 En
Getting started
INTRODUCTION
Remote control
1 Input buttons
Select an input source you want to listen to.
( P. 12)
2 MEMORY, TUNING / , PRESET / ,
INFO
Control an FM tuner. ( P. 14)
3 OPTION
Enters OPTION menu when operating FM
function or using Bluetooth component. ( P. 14,
17)
4 (MENU) / ( ) / ( ) / ( ) /
(Center)
Change the setting.
Control an iPod. ( P. 16)
S / T: Control the wheel of iPod.
5 RETURN
Returns to the previous menu or cancels preset
registration/pairing operation.
6 SUBWOOFER (+/–)
Adjust the volume balance of subwoofer.
( P. 19)
7 SURROUND MODE
Selects the surround mode. ( P. 13)
8 STEREO MODE
Turns extended stereo mode on and off alternately.
( P. 13)
9 UNIVOLUME
Turns UniVolume mode on and off. ( P. 13)
0 VOLUME (+/–)/MUTE
Control the volume of the system. ( P. 12)
A SETUP
Enters the setup menu. ( P. 18)
B
Turns on the system, or sets it to standby mode.
( P. 12)
1
B
A
@
9
8
2
3
4
5
6
7
Infrared signal
transmitter
8 En
PREPARATION
To enjoy quality sound thoroughly, place this system in the appropriate positions, and install the components
properly. The following illustrations are the setting images of this system.
Example 1 : Placing the speakers on the rack Example 2 : Mounting the speakers on the wall
1 Subwoofer integrated receiver (SR-300)
2 Speakers (NS-B380)
Do not place this system on/under any other components such as Blu-ray disc player in a pile. The vibration of this system
may cause system failure, etc. in other components.
Keep enough ventilation space on the front, rear, and bottom side (that attached legs) of this system. Do not place this
system on a thick carpet etc.
• If the picture on your CRT TV screen becomes blurred or distorted, we recommend moving the system away from your TV.
Low frequency sound produced by the subwoofer integrated receiver may be heard differently depending on the listening
position and subwoofer location. To enjoy desired sounds, try changing the location of the subwoofer integrated receiver.
• Depending on your installation environment, connections to external components can be done before installing this system.
We recommend that you temporarily place and arrange all components in order to decide which procedure is best done first.
Set the distance between the speakers to increase surround effect. ( P. 20)
You can place the speakers on a rack or attach it to a wall. Select an installation method that suits your environment.
Placing the speakers using the stands
You can place the speakers in an upright position or a horizontal position.
When placing the speakers in an upright
position
Place the speaker on the stand vertically, and then secure
it with the screw as shown in the illustration below.
When placing the speakers in a horizontal
position
Place the speaker on the stand horizontally, and then
secure it with the screw as shown in the illustration
below.
Placing
2
1
2
1
Notes
Placing the speakers
9 En
Placing
PREPARATION
Attaching the speakers to a wall
Installing the speakers using the keyholes
You can attach the speakers to a wall using
commercially available screws (#8, Diameter: 7 to 9
mm (1/4” to 3/8”)).
1 When placing the speakers on a wall,
remove the stands.
2 Install screws on a wall as shown in the
illustration.
The distance between the screws: 150
mm (5-7/8”) for both sides
3 Hang the speakers on the screws using
the keyholes on the back of the speakers.
Do not attach the speakers to a wall that is made of weak
materials such as plaster or veneered woods. Doing so
may cause the speakers to fall.
Use commercially available screws that can support the
weight of the installation.
• Make sure you use specified screws to attach the speakers.
Using clamps other than specified screws, such as short
screws, nails, or two-sided tape, may cause the speakers to
fall.
When connecting the speakers, fix the speaker cables in
place where they will not become loose. If your foot or
hand accidentally gets caught on a loose speaker cable, the
speakers may fall.
After attaching the speakers, check that the speakers are
fixed securely. Yamaha will bear no responsibility for any
accidents caused by improper installations.
When installing the speakers on a wall, all
installation work must be performed by a
qualified contractor or dealer. The customer
must never attempt to perform this installation
work. Improper or inadequate installation could
cause the speakers to fall, resulting in personal
injury.
Minimum
20 mm (3/4”)
6 mm
(1/4”)
150 mm
(5-7/8”)
Wall/wall
support
Vertical
Horizontal
150 mm
(5-7/8”)
Diameter: 7 to 9 mm
(#8, 1/4” to 3/8”)
Notes
10 En
Follow the procedure below to connect the subwoofer integrated receiver and the external components.
y
Connect your speaker as the center speaker of this system to the SPEAKERS terminal of the subwoofer integrated
receiver. ( P. 20)
Connection
Do not connect the power cable until all connections are completed.
Do not use excessive force when inserting the cable plug. Doing so may damage the cable plug and/
or terminal.
Overview
See “Connecting Blu-ray disc player or set-top
box”. ( P. 11)
Indoor FM antenna (supplied)
y
If the radio wave reception is weak in your area
or you want to improve the radio wave reception,
we recommend that you use an outdoor antenna.
For details, consult your nearest authorized
Yamaha dealer or Service Center.
See “Using optional
equipment”. ( P. 16)
To AC wall outlet
See “Connecting a TV”. ( P. 11)
Twist and pull off the
insulation tube on the
lead wire.
VCR, etc.
Insert to the terminal of the
correct polarity—positive
(+) to positive (+), and
negative (–) to negative (–).
White
Gray
y
After you have made all connections, connect the
power cable of the subwoofer integrated receiver.
Front Right
Speaker
Front Left
Speaker
11 En
Connection
PREPARATION
If a DVD player, etc., is connected to one of the HDMI IN jacks, connect your TV or video monitor (projector,
etc.) to the HDMI OUT jack of the subwoofer integrated receiver.
To output the sound of a TV from this system, you can select optical digital input and connect to digital output
jack.
y
For analog connection, you need to connect an audio cable to the analog input terminal.
You can connect external components with HDMI output. You can select from HDMI IN 1, 2, or 3. These
three jacks are identical.
Connecting a TV
TV
Signal flow
Connecting Blu-ray disc player or set-top box
Blu-ray disc player or
set-top box
12 En
BASIC OPERATION
Once you have finished all cable connections and remote control operation, follow the procedure below to start
basic playback operation.
1 Press .
This system is turned on and the STATUS
indicator lights green.
y
This system has the auto-sleep function, which will
automatically switch the system to turn off if the
system is left turned on for 24 hours without any
operation being performed.
2 Press one of the input buttons to select
an input source.
3 Start playback on the selected external
component.
For information on the external component, refer
to the instruction manual for the product.
4 Press VOLUME +/– to adjust the volume
level.
y
To turn off the volume temporarily, press MUTE.
While the mute function is activated, the VOLUME
indicator flashes. To resume the volume, press MUTE
again or press VOLUME +/–.
When sound of HDMI is output from the TV, the
volume level does not change if you press VOLUME
+/–.
Using the remote control
Basic playback operation
1
2
4
Note
Press again to set the system to
standby mode.
When the “HDMI CONTROL” is set to “ON”, the
STATUS indicator lights red. When the “HDMI
CONTROL” is set to “OFF”, the STATUS indicator
turns off. ( P. 19)
Within 6 m (20’)
Use the remote control within 6 m (20’) of the
subwoofer integrated receiver and point it toward the
remote control sensor.
Be careful not to spill liquid on the remote control.
Be careful not to drop the remote control.
Do not leave the remote control in a place that is:
hot or humid, such as near a heater or in a bathroom
–extremely cold
–dusty
Notes
BASIC
OPERATION
13 En
You can enjoy a realistic sound effect using Yamaha’s
exclusive AIR SURROUND XTREME.
Press SURROUND MODE to set
surround mode.
Press SURROUND MODE repeatedly until desired
mode appears in the front panel display.
Surround mode descriptions
y
The system automatically memorizes the settings assigned
to each input source. When you select another input, the
system automatically recalls the last settings for the selected
input.
An extended sound is achieved for a 2 channel source
such as a CD player.
Press STEREO MODE to enter extended
stereo mode.
Each time you press STEREO MODE, the function is
turned on (EXTENDED STEREO) and off (STEREO)
alternately.
“STEREO”: Reproduces the sound without any effect.
“EXTENDED STEREO”: Reproduces a wider stereo
image.
y
The default setting is “EXTENDED STEREO”.
The system memorizes the settings assigned to each input
source.
While watching TV, use this function when you feel
uncomfortable with the difference in volume between
channels, TV programs, and commercials to keep the
volume at an even level.
Press UNIVOLUME to activate or
deactivate the function.
When UniVolume is activated, UNIVOLUME
indicator is displayed and the sound volume of TV is
uniformed.
y
The system memorizes the setting assigned to each input
source.
When the input source is DOCK and UniVolume is
activated, compressed music enhancer function is invalid
(ENHANCER indicator disappears).
Enjoying sound modes
SURROUND MODE
STEREO MODE
UNIVOLUME
Surround mode
MOVIE This mode is useful when you enjoy
movie contents on media such as
Blu-ray disc, etc.
MUSIC This mode is useful when you listen to
music contents on media such as
Blu-ray disc, etc.
SPORTS This mode is useful when you enjoy
sports programs or TV news.
GAME This mode is useful when you enjoy
video games.
Stereo mode
UniVolume™
14 En
Automatic preset
You can store up to 40 FM stations (01 to 40).
1 Press OPTION to enter OPTION menu.
“AUTO PRESET” appears firstly in the front
panel display.
2 Press (Center).
y
Press PRESET / repeatedly to select a preset
number to which the first station will be stored.
After approximately 5 seconds, automatic
presetting starts from the lowest frequency and
proceeds through higher frequencies. When the
frequency is stored, the TUNED indicator lights
up.
When automatic preset tuning is completed, the front
panel display shows message “Preset Complete” for
three seconds firstly and returns to OPTION menu
secondly.
y
Press RETURN while searching automatically, automatic
preset is stopped.
Any stored station data existing under a preset number is
cleared when you store a new station under the same
preset number.
If the number of received stations does not reach 40,
automatic preset tuning automatically stops after
searching for all the available stations.
Only the station with strong signals can be stored. If the
desired station is not stored, or a station is not stored to the
desired preset number, preset the station manually.
( P. 15)
Listening to FM broadcasts
Basic tuning operation
Editing the preset FM station
FM
Sets the input to FM.
TUNING /
Press to change the frequency
by 1 step, or press and hold to
search stations automatically.
PRESET /
Select the preset FM
stations.
INFO
Selects the information
displayed in the front panel
display.
OPTION
Enters OPTION menu
when the input is set to FM.
Cursor in OPTION
menu
MEMORY
Stores preset stations
manually.
RETURN
Returns to the previous
menu or cancels the
operation.
Notes
15 En
Listening to FM broadcasts
BASIC
OPERATION
Manual station preset
Use this feature to preset your desired station
manually.
1 Tune into a radio station you want to
preset.
2 Press MEMORY.
“MANUAL PRESET” appears in the front panel
display, followed soon by the preset number to
which the station will be registered.
y
By pressing down MEMORY for more than 2
seconds. The station is registered to the lowest empty
preset number or a preset number one higher than the
last preset number.
3 Press PRESET / to select the preset
number (01 to 40) to which the station will
be registered.
When you select a preset number to which no
station is registered, EMPTY indicator appears on
the display. When you select a registered preset
number, a registered frequency is displayed on the
right of the preset number.
y
To cancel registration, press RETURN on the remote
control or leave the tuner without any operations for
about 30 seconds.
4 Press MEMORY again to register.
Clearing the preset station
1 Press OPTION to enter OPTION menu.
2 Display “CLEAR PRESET” using the
cursor and press (Center).
Preset number and the frequency appears in the
display.
y
You can cancel the operation and return to OPTION
menu by pressing RETURN on the remote control.
3 Select the preset number of the registered
station you want to clear using the cursor
/ and press (Center).
The preset station registered to the selected preset
number is cleared. To clear the registration of
multiple preset numbers, repeat the above steps.
To end the operation, press OPTION.
Using the monaural
reception mode
When the signal of the desired FM station is too weak,
set the reception mode to “MONO” to increase signal
quality.
1 Press OPTION to enter OPTION menu.
2 Display “STEREO/MONO” by using the
cursor and press (Center).
3 Select “MONO” to set the reception mode
to monaural by using the cursor / .
Switching the information
display
Each time you press INFO, the information display
changes as follows:
Information type
SURROUND MODE
Displays the surround mode or stereo mode.
FREQUENCY
Displays the frequency and preset number.
PROGRAM SERVICE (PS)
Displays the currently received Radio Data System
program.
PROGRAM TYPE (PTY)
Displays the type of the currently received Radio
Data System program.
RADIO TEXT (RT)
Displays the information of the currently received
Radio Data System program.
CLOCK TIME (CT)
Displays the current time.
Europe and Russia models only
16 En
This system is equipped with a DOCK terminal, which allows you to connect a Yamaha iPod universal dock (such
as YDS-11, sold separately) or a Yamaha Bluetooth wireless audio receiver (such as YBA-10, sold separately) to
enjoy music contents stored in your Bluetooth component (such as a portable music player or computer equipped
with Bluetooth transmitter, etc.). Connect this equipment to the DOCK terminal of the subwoofer integrated
receiver using its dedicated cable.
y
When DOCK is selected as the input source, compressed music enhancer function is activated automatically and enhances
your listening experience by regenerating the missing harmonics in a compressed music format such as MP3.
Once you have stationed your iPod in the Yamaha iPod universal dock connected to the DOCK terminal of the
subwoofer integrated receiver, you can enjoy playback of your iPod.
Supported iPod
iPod (Click and Wheel including iPod classic)
iPod nano
iPod mini
iPod touch
Battery charge feature
This system charges the battery of an iPod stationed in the Yamaha iPod universal dock connected to the DOCK
terminal of the subwoofer integrated receiver, even when this system is turned off. “Charging” appears in the
front panel display.
Some features may not be available depending on the model or the software version of your iPod.
• For a complete list of status messages that appear in the front panel display, see the “iPod” section in “Troubleshooting” (
P. 24).
Be sure to set the volume to minimum before docking or removing your iPod.
To playback an iPod, select DOCK for input source.
Refer to the instruction manual of your Yamaha iPod universal dock for details.
Using optional equipment
Connecting dock
Using iPod™
Notes
Yamaha iPod universal dock
(such as YDS-11, sold separately)
Yamaha Bluetooth wireless audio receiver
(such as YBA-10, sold separately)
Connect either component.
17 En
Using optional equipment
BASIC
OPERATION
Pairing
For details, refer to the instruction manual of Yamaha
Bluetooth wireless audio receiver.
1 Press DOCK to set the input to DOCK.
2 Turn on the Bluetooth component you
want to pair with, and then enter pairing
mode.
Refer to the instruction manual of your Bluetooth
component for details.
3 Press OPTION.
OPTION menu for DOCK input appears in the
display.
4 Press the cursor to select “PAIRING”
and press (Center).
“Searching...” appears when the pairing starts.
While the Yamaha Bluetooth wireless audio
receiver is in pairing mode, the DOCK indicator
flashes in the front panel display.
y
To cancel pairing, press RETURN.
5 Check that the Bluetooth component
detects the Yamaha Bluetooth wireless
audio receiver.
If the Bluetooth component detects the Yamaha
Bluetooth wireless audio receiver, the audio
receiver name (“YBA-10 YAMAHA” for
example) appears in the device list of the
Bluetooth component.
6 Select the Yamaha Bluetooth wireless
audio receiver in the device list of the
Bluetooth component, and then enter the
pass key “0000” on the Bluetooth
component.
Establishing a connection
After the pairing is completed, perform the connecting
operation on the system or on the Bluetooth
component to enable communication between them.
The connecting operation on the system is only
available for the most recently connected Bluetooth
component.
1 Press DOCK to set the input to DOCK.
2 Press OPTION to enter OPTION menu.
“CONNECT” appears firstly in the front panel
display.
3 Press (Center).
“Searching...” appears firstly in the front panel
display.
When the system finds the last connected
Bluetooth component, “BT connected” appears in
the front panel display for 3 seconds.
y
• If the system cannot find the last connected Bluetooth
component, “Not found” appears in the front panel
display.
• If you want to establish a connection with a Bluetooth
component other than the one most recently
connected to, connect from that Bluetooth
component. Refer to the instruction manual of your
Bluetooth component for details.
To disconnect the Bluetooth wireless audio receiver from
the Bluetooth component, display OPTION menu again,
select “Disconnected,” and press (Center).
Using Bluetooth™ components
About “Pairing”
Pairing must be performed before using a Bluetooth
component with the Yamaha Bluetooth wireless
audio receiver connected to the system for the first
time or if the registered pairing data has been
deleted. “Pairing” refers to the operation of
registering a Bluetooth component for Bluetooth
communications.
y
To ensure security, a time limit of 8 minutes is set for the
pairing operation. Please read and fully understand all the
instructions before starting.
Note
Note
18 En
USEFUL OPERATION
Setup menu list
You can change various settings of this system using
the setup menu.
1 Press SETUP to enter the setup menu.
“SW LEVEL” is displayed in the front panel
display.
2 Press the cursor / to select menu
and press (Center).
The current setting is displayed.
3 Press the cursor / to adjust the
value of each menu.
Press and hold the cursor / to change the
setting value faster.
4 Press SETUP again to exit the setup
menu.
y
Press RETURN to return to the previous menu.
If you do not operate within 30 seconds after entering the
setup menu, the system automatically exits the setup menu.
Setup menu
Overview
Item Description of function Page
1: SW LEVEL
Adjusting the volume balance during playback P. 192: CENTER LEVEL
3: SUR. LEVEL
4: TONE BASS
Adjusting high/low frequency sound (tone control) P. 19
5: TONE TREBLE
6: AUDIO DELAY Adjusting the audio delay P. 19
7: HDMI AUDIO Setting the audio output P. 19
8: HDMI CONTROL Switching on/off the HDMI control function P. 19
9: DISPLAY MODE Changing the brightness of the front panel display P. 20
10: SP TYPE Changing the setting of the speaker type P. 20
11: SP DISTANCE Setting the distance between the speakers P. 20
Basic procedure
1, 4
2, 3
Note
19 En
Setup menu
USEFUL
OPERATION
You can adjust the volume balance of the virtual
speakers and subwoofer.
Parameter
“SW LEVEL”: Adjusts the output level of the
subwoofer channel.
“CENTER LEVEL”: Adjusts the output level of the
virtual center speaker channel.
“SUR. LEVEL”: Adjusts the output level of the
surround/surround back virtual speaker channels.
Adjustable range
–6 to +6 (Default setting: 0)
y
You can also adjust the output level of the subwoofer by
pressing SUBWOOFER +/–.
If surround mode is off, the virtual center speaker and
virtual surround effects become invalid.
You can adjust the balance of the high frequency
range (Treble) and low frequency range (Bass) of
sounds output from the front speakers to obtain
desired tone.
Parameter
“TONE BASS”: Adjusts the balance of the low
frequency range (Bass) of sounds output from the
speaker.
“TONE TREBLE”: Adjusts the balance of the high
frequency range (Treble) of sounds output from the
speaker.
Adjustable range
–6 to +6 (Default setting: 0)
Flat panel display TV images sometimes lag behind
the sound. You can use this function to delay the
sound output to synchronize it with the video image.
Parameter
“AUDIO DELAY”
Adjustable range (Default setting: “AUTO”)
“AUTO”, 0 to 240 ms (You can adjust the delay time
by the 10 ms.)
* “AUTO”: If you operate HDMI connection to a TV with
the function to automatically adjusting the audio delay,
you can adjust the delay time automatically.
The system memorizes the settings assigned to each input
source.
You can select this system (or a TV connected to this
system via the HDMI OUT jack of this system) for
reproducing sound signals input from the HDMI IN
jack in the setup menu.
Parameter
“HDMI AUDIO”
Adjustable option (Default setting: “AMP”)
“AMP”: Outputs HDMI sound signals from the
speakers connected to this system.
“TV”: Outputs HDMI sound signals from the speakers
of a TV connected to this system. Sound output from
the speakers connected to this system is muted.
The volume level will not change from pressing
VOLUME +/– or MUTE while output from the TV.
You cannot change the audio output when “HDMI
CONTROL” is set to “ON”.
You can set whether to use the HDMI control
function. Refer to P.21 for HDMI control function.
Parameter
“HDMI CONTROL”
Adjustable option (Default setting: “OFF”)
“ON”: Activates the HDMI control function.
“OFF”: Deactivates the HDMI control function.
Adjusting the volume balance
during playback
Adjusting high/low frequency
sound (tone control)
Adjusting the audio delay
Note
Setting the audio output
Notes
Switching on/off the HDMI™
control function
Setup menu
20 En
You can change the brightness of the front panel
display. You can also turn off the front panel display
to view a movie in a darker environment.
The brightness of the front panel changes as follows.
Parameter
“DISPLAY MODE”
Adjustable range
(Default setting: “DIMMER 0”)
* Selecting DISPLAY OFF turns off the front panel display
after exiting the setup menu.
• The front panel display lights up momentarily when any
operation is performed with DISPLAY OFF mode selected.
• Only the STATUS indicator remains lit in DISPLAY OFF
mode.
You can set the speaker type if you want to add or
change speakers. When you connect only the supplied
speaker, you do not have to change the setting.
Parameter
“SP TYPE”
Adjustable range (Default setting: “2CH”)
“BAR”: When you connect a speaker with integrated
front left/right/center channels (such as a bar-type
speaker).
“2CH”: When you connect front left/right (2-channel)
speakers.
“3CH”: When you connect front left/right (2-channel)
speakers and a center speaker.
To activate “SP TYPE”, set the system to standby mode
and turn on again after setting the speaker type.
“SP DISTANCE” is displayed when “2CH” or “3CH” is
selected.
Select a parameter suited for the distance between the
front left and right speakers, to obtain the most
suitable surround effect.
Parameter
“SP DISTANCE”
Adjustable range
(Default setting: “NORMAL”)
“WIDE”: When the distance between the front
speakers is over 150 cm (59-1/16”).
“NORMAL”: When the distance between the front
speakers is from 80 cm (31-1/2”) to 150 cm (59-1/
16”).
“NARROW”: When the distance between the front
speakers is within 80 cm (31-1/2”).
When the surround mode is off, this function is invalid.
Changing the brightness of the
front panel display
Notes
Changing the setting of the
speaker type
Notes
Bright
Dark
Setting the distance between the
speakers
Note
21 En
Setup menu
USEFUL
OPERATION
You can operate the following functions of this system
with the remote control of your TV when the TV
(HDMI control function supported) is connected to the
HDMI OUT jack of this system.
Turning this system on or to standby mode
(conjunction with TV)
Adjusting the volume
Selecting a device to reproduce TV sounds (this
unit or TV)
y
Even if your TV supports the HDMI control function,
some functions may not be available. For details, refer to
the instruction manual supplied with your TV.
• If you connect this system and Blu-ray disc player or DVD
player (HDMI control function supported) to HDMI, you
can also control those devices with the HDMI control
function. For details, refer to the instruction manual
supplied with each device.
We suggest that you use products (TV, Blu-ray disc/DVD
player, etc.) from the same manufacturer.
The HDMI control-compatible components include
Panasonic VIERA Link compatible TV, DVD player/
recorder and Blu-ray disc player.
When “HDMI CONTROL” is set to “ON”, operations of
the TV (for example, changing channels, etc.) may change
the system settings, such as the surround mode.
(Steps 1 through 3 are required for the HDMI
control function setup.)
1 Turn on all devices connected to this
system with HDMI.
2 Enable the HDMI control function on each
device.
For this system, set “HDMI CONTROL” to “ON”
( P. 19).
For external devices, refer to the instruction
manual supplied with each device.
3 Turn off the TV, and then turn it on again.
(Step 4 through 6 are required for making the
TV learn linked devices. If the connections or
devices are switched, you need to carry out
these steps again.)
4 Select this system as the input source of
the TV.
5 Turn on the HDMI control device (Blu-ray
disc or DVD player) connected to this
system.
6 Select the HDMI control device (Blu-ray
disc or DVD player) as the input source of
this system to check the video input.
7 Check if the HDMI control function works
(turn on this system or adjust the volume
level using the remote control of the TV).
In case the HDMI control function does not work, check the
followings. Also turning off (unplug) and turning on (plug)
the TV may be effective.
The TV is connected to the HDMI OUT jack of this
system.
“HDMI CONTROL” is set to “ON” on this system.
The HDMI control function is enabled on the TV.
Using the HDMI™ control
function
Note
When “HDMI CONTROL” is set to “ON”, even if
you press , the system will not be completely
turned off and the signal from HDMI input terminal
to HDMI output terminal is output.
y
• The STATUS indicator in the front panel display lights
red when “HDMI CONTROL” is set to “ON” and the
system is in standby mode.
Before pressing , select desired input sources
connected to HDMI input (HDMI IN 1 to 3).
22 En
ADDITIONAL INFORMATION
If there is any problem with the system, check the following items. If you cannot solve a problem with the
following remedies, or if the problem is not listed below, turn off and unplug the system, and then consult your
nearest authorized Yamaha dealer or Service Center.
Additional information
Troubleshooting
Problem Cause Solution
See
page
Power turns on but
immediately shuts off.
The power cable may be connected
improperly.
Make sure the power cable is plugged into
the outlet firmly.
10
A speaker cable may be shorted. Make sure all speaker cables are connected
properly.
10
This system may have received a
strong electrical shock, such as from a
lightening bolt or excessive static
electricity.
Set this system to standby mode, and then
disconnect the power cable. Wait for about
30 seconds, connect the power cable, and
then turn the system on again.
12
The speakers make no
sound.
The volume may be set to minimum
level.
Adjust the volume level.
12, 19
The mute function may be activated. Cancel the mute function. 12
The input source or input setting may
be incorrect.
Select the correct input source or input
setting.
12
The cables may be connected
improperly.
Make sure all cables are connected
properly.
10
“HDMI AUDIO” in the setup menu is
set to “TV”.
Set “HDMI AUDIO” in the setup menu to
“AMP”.
19
Sound is too low on
one side.
The cables may be connected
improperly.
Make sure all cables are connected
properly.
10
Speaker channels
other than the front
ones make no sound.
You may be listening to stereo sounds
without surround mode.
Press a surround mode button to enable the
sound field effect.
13
“SUR. LEVEL” in the setup menu is
set to minimum level.
Adjust “SUR. LEVEL” in the setup menu.
19
The subwoofer makes
no sound.
The volume of the subwoofer channel
may be set to minimum level.
Adjust the volume level of the subwoofer.
7, 19
The source does not contain low-
frequency signals.
The volume level
decreases without any
operation.
You turned off the system when the
volume level was over 70.
The volume level is automatically set to 70
the next time you turn on the system to
protect the speakers.
Sound is poor (noisy).
A speaker cable may be shorted. Make sure all cables are connected
properly.
10
This system does not
operate properly.
This system may receive a strong
electrical shock, such as from a
lightening bolt or excessive static
electricity, or drop in power supply.
Set this system to standby mode, and then
disconnect the power cable. Wait for about
30 seconds, connect the power cable, and
then turn on this system.
12
A digital or high-
frequency equipment
produces noises.
The system may be placed close to
digital equipment or high-frequency
equipment.
Place this system farther away from such
equipment.
23 En
Additional information
ADDITIONAL
INFORMATION
HDMI
Tuner
The system settings
change automatically.
When “HDMI CONTROL” is set to
“ON”, operations of the TV (for
example, changing channels, etc.) may
change the system settings, such as the
surround mode.
Set “HDMI CONTROL” to “OFF” or set
the system again by using its remote
control. 21
The remote control
does not operate the
system.
The system may be outside the remote
control operation range.
For information on the remote control
operation range, refer to “Using the remote
control”.
12
The remote control sensor of this
system may be exposed to direct
sunlight or lighting.
Change the lighting.
The batteries may be worn out. Replace the batteries. 4
Problem Cause Solution
See
page
“AUTO” set in the
setup menu “AUDIO
DELAY” does not
operate.
The TV does not support
automatically adjusting the audio
delay.
Adjust the delay time manually (0 to 240
ms).
19
The HDMI control
function does not
operate properly.
The number of the connected HDMI
components is over the limit.
Disconnect some of the HDMI
components.
No picture or sound
The connected HDMI component does
not support high-bandwidth digital
copyright protection (HDCP).
Connect the HDMI component that
supports HDCP.
Problem Cause Solution
See
page
FM stereo reception is
noisy.
The characteristics of FM stereo
broadcasts may cause this problem
when the transmitter is too far away, or
if the antenna quality is poor.
Check the antenna connections. 10
Try using a high-quality directional FM
antenna.
Set the reception mode to “MONO”. 15
There is distortion, and
clear reception cannot
be obtained, even with
a good FM antenna.
There is multi-path interference. Adjust the antenna position to eliminate
multi-path interference.
The desired station
cannot be tuned into
with the automatic
tuning method.
The signal is too weak. Use a high-quality directional FM antenna.
Set the reception mode to “MONO” and
press TUNING / to change
frequency by 1 step.
14, 15
Problem Cause Solution
See
page
Additional information
24 En
iPod
Bluetooth
Status message Cause Solution
See
page
Unknown iPod
The iPod being used is not supported
by this system.
Only iPod (Click and Wheel including iPod
classic), iPod nano, iPod mini, and iPod
touch are supported.
iPod connected
Your iPod is properly stationed in the
Yamaha iPod universal dock (such as
YDS-11, sold separately) connected to
the DOCK terminal of this system, and
the connection between your iPod and
this system is completed.
Disconnected
Your iPod was removed from the
Yamaha iPod universal dock (such as
YDS-11, sold separately) connected to
the DOCK terminal of this system.
Station your iPod back in the Yamaha iPod
universal dock (YDS-11, sold separately)
connected to the DOCK terminal of this
system.
16
Charging
Your iPod is charging.
Status message Cause Solution
See
page
Searching...
The Yamaha Bluetooth wireless audio
receiver (such as YBA-10, sold
separately) and the Bluetooth
component are in the process of the
pairing.
The Yamaha Bluetooth wireless audio
receiver (such as YBA-10, sold
separately) and the Bluetooth
component are in the process of
establishing the connection.
Completed
The pairing is completed.
Canceled
The pairing is canceled.
Not found
The system cannot find the Bluetooth
component while performing the
pairing or trying to connect to the
Bluetooth component.
BT connected
The connection between the Yamaha
Bluetooth wireless audio receiver (such
as YBA-10, sold separately) and the
Bluetooth component is established.
Disconnected
The Bluetooth component is
disconnected from the Yamaha
Bluetooth wireless audio receiver (such
as YBA-10, sold separately).
Not Available
The pairing is performed when the
Yamaha Bluetooth wireless audio
receiver (such as YBA-10, sold
separately) is connected to the
Bluetooth component.
Perform the pairing when the Yamaha
Bluetooth wireless audio receiver (such as
YBA-10, sold separately) is not connected
to the Bluetooth component.
17
25 En
Additional information
ADDITIONAL
INFORMATION
AIR SURROUND XTREME
This system employs new technologies and algorithms
that make it possible to achieve 7-channel surround
sound with only front speakers, and without using wall
reflections.
Ordinarily, two front speakers, a center speaker, two
surround speakers, and a subwoofer are necessary for
enjoying 5.1 channel surround sound.
Virtual 7.1 channel
The AIR SURROUND XTREME technology, using
only front speakers and subwoofer, enables you to
enjoy a realistic 7.1 channel sound by simulating
sound from virtual speakers at center, surround, and
surround backs.
Channel (ch)
A channel is an audio type that has been divided based
on range and other characteristics.
Ex. 7.1 channel
Front speakers, Left (1ch), Right (1ch)
Center speaker (1ch)
Surround speakers, Left (1ch), Right (1ch)
Surround back speakers, Left (1ch), Right (1ch)
Subwoofer (1ch × 0.1
*
= 0.1ch)
* In contrast to a full 1-channel band, a component
designed to enhance low frequency sound for added
effect.
Deep Color
Deep Color refers to the use of various color depths in
displays, up from the 24-bit depths in previous
versions of the HDMI specification. This extra bit
depth allows HDTVs and other displays go from
millions of colors to billions of colors and eliminate
on-screen color banding for smooth tonal transitions
and subtle gradations between colors. The increased
contrast ratio can represent many times more shades of
gray between black and white. Also Deep Color
increases the number of available colors within the
boundaries defined by the RGB or YCbCr color space.
Dolby Digital
Digital surround sound system which is developed by
Dolby Laboratories provides completely independent
multi-channel audio. With 3 front channels (left,
center, and right) and 2 surround stereo channels,
Dolby Digital provides five full-range audio channels.
With an additional channel especially for bass effects
(called LFE, or low frequency effect), the system has a
total of 5.1 channels (LFE is counted as 0.1 channel).
By using 2 channel stereo for the surround speakers,
more accurate moving sound effects and surround
sound environment are possible than with Dolby
Surround.
Glossary
Front speakers
Subwoofer
Center speaker
Surround speakers
Typical 5.1 channel speaker system
The system creates the virtual 7.1 channel surround sound with the
subwoofer integrated receiver and the speaker.
C: Center speaker
FR, FL: Front speakers
SW: Subwoofer
SR, SL: Surround virtual speakers
SBR, SBL: Surround back virtual speakers
The sound image of the system
Additional information
26 En
Dolby Pro Logic II
It is an improved matrix decoding technology that
provides better spatiality and directionality on Dolby
Surround programmed material; provides a
convincing three-dimensional sound field on
conventional stereo music recordings; and is ideally
suited to bring the surround experience to automotive
sound. While conventional surround programming is
fully compatible with Dolby Pro Logic II decoders,
soundtracks will be able to be encoded specifically to
take full advantage of Pro Logic II playback, including
separate left and right surround channels.
DTS
Digital surround sound system developed by DTS,
Inc., which provides 5.1 channel audio. With an
abundance of audio data, it is able to provide
authentic-sounding effects.
HDMI
HDMI (High-Definition Multimedia Interface) is the
first industrysupported, uncompressed, all-digital
audio/video interface. Providing an interface between
any source (such as a set-top box or AV receiver) and
an audio/video monitor (such as a digital television),
HDMI supports standard, enhanced or high-definition
video as well as multichannel digital audio using a
single cable. HDMI transmits all ATSC HDTV
standards and supports 8 channel digital audio, with
bandwidth to spare to accommodate future
enhancements and requirements. When used in
combination with HDCP (High-bandwidth Digital
Content Protection), HDMI provides a secure audio/
video interface that meets the security requirements of
content providers and system operators. For further
information on HDMI, visit the HDMI website at
“http://www.hdmi.org/.”
PCM (Pulse Code Modulation)
A signal that is changed to digital format without
compression. A CD is recorded with 16-bit sound at
44.1 kHz, while DVD recording is anywhere from 16
bits at 48 kHz to 24 bits at 192 kHz, which makes it a
higher quality sound than CD.
Sampling frequency
The number of sampling (process for digitalizing
analog signals) per second. In principle, the higher the
sampling rate, the wider the frequency range that can
be played back, and the higher the quantized bit rate,
the finer the sound that can be reproduced.
x.v.Color
A color space standard supported by HDMI version
1.3. It is a more extensive color space than sRGB, and
allows the expression of colors that could not be
expressed before. While remaining compatible with
the color gamut of sRGB standards, “x.v.Color
expands the color space and can thus produce more
vivid, natural images. It is particularly effective for
still pictures and computer graphics.
27 En
Additional information
ADDITIONAL
INFORMATION
SR-300
AUDIO SECTION
Minimum RMS Output Power
Front Left and Right (1 kHz, 1% THD, 6 Ω)
................................................................ 45 W+45 W
Center (1 kHz, 1% THD, 6 Ω).......................... 45 W
Subwoofer (100 Hz, 1% THD, 3 Ω) ................. 90 W
•Maximum Power
Front Left and Right (1 kHz, 10% THD, 6 Ω)
................................................................ 50 W+50 W
Center (1 kHz, 10% THD, 6 Ω)........................ 50 W
Subwoofer (100 Hz, 10% THD, 3 Ω) ............. 100 W
FM SECTION
Tuning Range
[U.S.A. and Canada models]........87.5 to 107.9 MHz
[Other models] .........................87.50 to 108.00 MHz
Frequency Step
[U.S.A. and Canada models].........................200 kHz
[Other models] ................................................50 kHz
Antenna Input (unbalanced)............................... 75 Ω
SUBWOOFER SECTION
Type ................................................. Bass reflex type
Non-magnetic shielding type
Driver .......................................13 cm (5-1/4 in) cone
Frequency Response ........................35 Hz to 150 Hz
Impedance ............................................................ 3 Ω
GENERAL
•Power Supply
[U.S.A. and Canada models] .......... AC120 V, 60 Hz
[Other models] ....................AC220-240 V, 50/60 Hz
Power Consumption...........................................35 W
Standby Power Consumption
[U.S.A. and Canada models] .............less than 0.4 W
[Other models] ...................................less than 0.5 W
Dimensions (W × H × D) .........435 × 151 × 361 mm
(17-1/8 × 6 × 14-1/4 in)
Weight...............................................................8.6 kg
NS-B380
Type ...................... 2 way Accoustic suspension type
Non-magnetic shielding type
•Driver
Woofer ..............................6.5 cm (2-1/2 in) cone × 2
Tweeter ..........2.5 cm (1 in) Balanced dome type × 1
Frequency Response ...................... 150 Hz to 20 kHz
Impedance............................................................ 6 Ω
Dimensions (W × H × D)
NS-B380 .....................................90 × 220 × 109 mm
(3-1/2 × 8-5/8 × 4-1/4 in)
Stand .............................................87 × 63 × 120 mm
(3-3/8 × 2-1/2 × 4-3/4 in)
Weight...............................................................1.0 kg
* Specifications are subject to change without notice.
This system employs new technologies and algorithms that
make it possible to achieve 7-channel surround sound with
only two front speakers, and without using wall reflections.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are trademarks
of Dolby Laboratories.
“DTS” and “DTS Digital Surround” are registered trademarks
of DTS, Inc.
iPod™
“iPod” is a trademark of Apple Inc., registered in the U.S. and
other countries.
Bluetooth™
Bluetooth is a registered trademark of Bluetooth SIG and is
used by Yamaha in accordance with a license agreement.
“HDMI,” the “HDMI” logo and “High-Definition Multimedia
Interface” are trademarks, or registered trademarks of HDMI
Licensing LLC.
x.v.Color™
“x.v.Color” is a trademark of Sony Corporation.
“UniVolume” is a trademark of Yamaha Corporation.
Specifications
Additional information
28 En
HDMI signal compatibility
Audio signals
y
Refer to the supplied instruction manuals of the input source component, and set the component appropriately.
When CPPM copy-protected DVD-Audio is played back, video and audio signals may not be output depending on the type
of the DVD player.
This unit is not compatible with HDCP-incompatible HDMI or DVI components.
To decode audio bitstream signals on this unit, set the input source component appropriately so that the component outputs
the bitstream audio signals directly (does not decode the bitstream signals on the component). Refer to the supplied
instruction manuals for details.
Video signals
This unit is compatible with the video signals of the following resolutions:
480i/60 Hz
576i/50 Hz
480p/60 Hz
576p/50 Hz
720p/60 Hz, 50 Hz
1080i/60 Hz, 50 Hz
1080p/60 Hz, 50 Hz, 24 Hz
Available signal information
Audio signal types Audio signal formats Compatible media
2ch Linear PCM 2ch, 32-96 kHz, 16/20/24 bit CD, DVD-Video, DVD-Audio, etc.
Multi-ch Linear PCM 8ch, 32-96 kHz, 16/20/24 bit DVD-Audio, Blu-ray disc, HD DVD, etc.
Bitstream Dolby Digital, DTS DVD-Video, etc.
YC173A0/OMEN2

Transcripción de documentos

Home Theater Package (Subwoofer Integrated Receiver + Speaker) YHT-S300 (SR-300 + NS-B380) Owner’s Manual English Caution: Read this before operating your unit. 1 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 2 Install this unit in a well ventilated, cool, dry, clean place - away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. For proper ventilation, allow the following minimum clearances. Top: 5 cm (2 in) Rear: 5 cm (2 in) Sides: 5 cm (2 in) 3 Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds. 4 Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in an environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury. 5 Avoid installing this unit where foreign objects may fall onto this unit and/or this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place: – Other components, as they may cause damage and/or discoloration on the surface of this unit. – Burning objects (i.e. candles), as they may cause fire, damage to this unit, and/or personal injury. – Containers with liquid in them, as they may fall and liquid may cause electrical shock to the user and/or damage to this unit. 6 Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury. 7 Do not plug in this unit to a wall outlet until all connections are complete. 8 Do not operate this unit upside-down. It may overheat, possibly causing damage. 9 Do not use force on switches, knobs and/or cords. 10 When disconnecting the power cable from the wall outlet, grasp the plug; do not pull the cable. 11 Do not clean this unit with chemical solvents; this might damage the finish. Use a clean, dry cloth. 12 Only voltage specified on this unit must be used. Using this unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/ or personal injury. Yamaha will not be held responsible for any damage resulting from use of this unit with a voltage other than specified. 13 To prevent damage by lightning, keep the power cable and outdoor antennas disconnected from a wall outlet or the unit during a lightning storm. 14 Do not attempt to modify or fix this unit. Contact qualified Yamaha service personnel when any service is needed. The cabinet should never be opened for any reasons. 15 When not planning to use this unit for long periods of time (i.e. vacation), disconnect the AC power plug from the wall outlet. 16 Be sure to read the “Troubleshooting” section on common operating errors before concluding that this unit is faulty. 17 Before moving this unit, press to set this unit in 2 En 18 19 20 21 standby mode, and disconnect the power supply cable from the wall outlet. Condensation will form when the surrounding temperature changes suddenly. Disconnect the power supply cable from the outlet, then leave the unit alone. Install this unit near the wall outlet and where the AC power plug can be reached easily. The batteries shall not be exposed to excessive heat such as sunshine, fire or like. Secure placement or installation is the owner’s responsibility. Yamaha shall not be liable for any accident caused by improper placement or installation of speakers. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if you turn off this unit by . In this state, this unit is designed to consume a very small quantity of power. ■ For U.K. customers If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described below. Note The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live socket outlet. ■ Special Instructions for U.K. Model IMPORTANT THE WIRES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: Blue: NEUTRAL Brown: LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Making sure that neither core is connected to the earth terminal of the three pin plug. INTRODUCTION USEFUL OPERATION Overview .............................................................18 Basic procedure...................................................18 Adjusting the volume balance during playback ...........................................................19 Adjusting high/low frequency sound (tone control)....................................................19 Adjusting the audio delay....................................19 Setting the audio output ......................................19 Switching on/off the HDMI™ control function ............................................................19 Changing the brightness of the front panel display..............................................................20 Changing the setting of the speaker type ............20 Setting the distance between the speakers ..........20 Using the HDMI™ control function ...................21 PREPARATION Placing .................................................................8 Placing the speakers .............................................. 8 Connection ........................................................10 Overview............................................................. 10 Connecting a TV ................................................. 11 Connecting Blu-ray disc player or set-top box ....................................................... 11 BASIC OPERATION Basic playback operation.................................12 ADDITIONAL INFORMATION Additional information.................................... 22 Surround mode.................................................... 13 Stereo mode ........................................................ 13 UniVolume™...................................................... 13 Troubleshooting ..................................................22 Glossary...............................................................25 Specifications ......................................................27 Available signal information...............................28 Listening to FM broadcasts.............................14 Basic tuning operation ........................................ 14 Editing the preset FM station .............................. 14 Using optional equipment................................16 Connecting dock ................................................. 16 Using iPod™....................................................... 16 Using Bluetooth™ components .......................... 17 • In this manual, operations that can be performed using either the front panel buttons or the remote control are explained using the remote control. • y indicates a tip for your operation. Notes contain important information about safety and operating instructions. • This manual is produced prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In case of differences between the manual and the product, the product has priority. 3 En ADDITIONAL INFORMATION ■ About this manual USEFUL OPERATION Enjoying sound modes .....................................13 BASIC OPERATION Setup menu ....................................................... 18 Supplied parts........................................................ 4 Controls and functions .......................................... 5 PREPARATION Getting started ....................................................4 INTRODUCTION Contents INTRODUCTION Getting started Supplied parts This product consists of the following items. Before making connections, make sure you have received all of the following items. ■ Units Subwoofer Integrated Receiver (SR-300) Speakers (NS-B380) ■ Accessories Speaker cable (3 m × 2) Remote control Indoor FM antenna (Asia model) Stand × 2 (for speaker) Battery × 2 (AAA, R03, UM4) Screw × 2 (for stand) Quick Reference Guide (Europe and Russia models) CD-ROM (Owner’s Manual) ■ Installing the batteries Notes • If the effective operation distance of the remote control decreases considerably, replace the batteries with two new ones as soon as possible. • Do not use an old battery together with new one. • Do not use different types of batteries (for example, alkaline and manganese) together. Their performance will vary, even if they are similar in shape. • If the batteries run out, immediately remove them from the remote control to prevent an explosion or acid leak. • Dispose of batteries according to regional regulations. • If a battery starts leaking, dispose of it immediately. Be careful not to let leaking battery acid come into contact with your skin or clothing. Before inserting new batteries, wipe the compartment clean. 4 En Getting started INTRODUCTION Controls and functions ■ Front panel of the subwoofer integrated receiver 1 2 3 4 5 6 3 INPUT Selects an input source you want to listen to. (☞ P. 12) 1 Turns on the system, or sets it to standby mode. (☞ P. 12) Note A small amount of electricity is consumed to receive the infrared signal from the remote control even when the system is in standby mode. 2 STATUS indicator Lights up to show the system condition. (☞ P. 12) 4 VOLUME –/+ Controls the volume of the system. (☞ P. 12) 5 Remote control sensor Receives infrared signals from the remote control. (☞ P. 7, 10) 6 Front panel display Shows information about the operational status of the system. (☞ P. 12) ■ Rear panel of the subwoofer integrated receiver 7 1 1 Power Cable For connecting an AC wall outlet. (☞ P. 10) 2 HDMI IN 1 - 3/HDMI OUT • HDMI IN 1 - 3 for connecting HDMI compatible external components. (☞ P. 11) • HDMI OUT for connecting an HDMI compatible TV. (☞ P. 11) 3 DIGITAL IN jack For connecting optical digital cable to the TV. (☞ P. 11) 6 5 4 3 2 4 ANALOG INPUT jack For connecting analog audio cable to external components. (☞ P. 10) 5 DOCK terminal For connecting an optional Yamaha iPod universal dock (such as YDS-11, sold separately) or Bluetooth wireless audio receiver (such as YBA10, sold separately). (☞ P. 16) 6 ANTENNA terminal For connecting supplied FM antenna. (☞ P. 10) 7 SPEAKERS terminal For connecting speakers. (☞ P. 10) 5 En Getting started ■ Front panel display of the subwoofer integrated receiver 1 2 8 7 6 1 HDMI indicator Lights up during normal communication when HDMI is selected as an input source. 2 Tuner indicators TUNED indicator Lights up when the system is receiving a station. (☞ P. 14) STEREO indicator Lights up when the system is receiving a strong signal from an FM stereo broadcast station in automatic tuning mode. (☞ P. 14) AUTO indicator Flashes when the system is tuning station automatically. (☞ P. 14) MEMORY indicator Flashes when the system is storing a station. (☞ P. 14, 15) EMPTY indicator Lights up when the storing preset number is empty. (☞ P. 15) PS/PTY/RT/CT indicator (Europe and Russia models only) Lights up according to the available Radio Data System information. (☞ P. 15) 3 Decoder indicators The respective indicator lights up when any of the decoders of the system is activated. 6 En 3 4 5 4 DOCK indicator • Lights up when the system is receiving a signal from an iPod stationed in the Yamaha iPod universal dock (such as YDS-11, sold separately) connected to the DOCK terminal of the subwoofer integrated receiver. (☞ P. 16) • Lights up while the Yamaha Bluetooth wireless audio receiver (such as YBA-10, sold separately) is connected to the Bluetooth component. (☞ P. 17) • Flashes while the connected Yamaha Bluetooth wireless audio receiver (such as YBA-10, sold separately) and the Bluetooth component are pairing (☞ P. 17) or while the Yamaha Bluetooth wireless audio receiver is searching for the Bluetooth component. (☞ P. 17) 5 VOLUME indicator • Indicates the current volume level. • Flashes while the mute function is activated. (☞ P. 12) 6 Multi information display Shows the selected input source, current sound mode and other information. 7 ENHANCER indicator Lights up when compressed music enhancer function is activated. (☞ P. 16) 8 UNIVOLUME indicator Lights up when UniVolume mode is selected. (☞ P. 13) Getting started 1 Input buttons Select an input source you want to listen to. (☞ P. 12) Infrared signal transmitter 2 MEMORY, TUNING / , PRESET INFO Control an FM tuner. (☞ P. 14) B 2 3 A 5 7 (MENU) / ( )/ ( )/ (Center) • Change the setting. • Control an iPod. (☞ P. 16) S / T: Control the wheel of iPod. ( )/ 5 RETURN Returns to the previous menu or cancels preset registration/pairing operation. 6 SUBWOOFER (+/–) Adjust the volume balance of subwoofer. (☞ P. 19) 4 6 , 3 OPTION Enters OPTION menu when operating FM function or using Bluetooth component. (☞ P. 14, 17) 4 1 / 7 SURROUND MODE Selects the surround mode. (☞ P. 13) @ 9 8 8 STEREO MODE Turns extended stereo mode on and off alternately. (☞ P. 13) 9 UNIVOLUME Turns UniVolume mode on and off. (☞ P. 13) 0 VOLUME (+/–)/MUTE Control the volume of the system. (☞ P. 12) A SETUP Enters the setup menu. (☞ P. 18) B Turns on the system, or sets it to standby mode. (☞ P. 12) 7 En INTRODUCTION ■ Remote control PREPARATION Placing To enjoy quality sound thoroughly, place this system in the appropriate positions, and install the components properly. The following illustrations are the setting images of this system. Example 1 : Placing the speakers on the rack Example 2 : Mounting the speakers on the wall 2 2 1 1 1 Subwoofer integrated receiver (SR-300) 2 Speakers (NS-B380) Notes • Do not place this system on/under any other components such as Blu-ray disc player in a pile. The vibration of this system may cause system failure, etc. in other components. • Keep enough ventilation space on the front, rear, and bottom side (that attached legs) of this system. Do not place this system on a thick carpet etc. • If the picture on your CRT TV screen becomes blurred or distorted, we recommend moving the system away from your TV. • Low frequency sound produced by the subwoofer integrated receiver may be heard differently depending on the listening position and subwoofer location. To enjoy desired sounds, try changing the location of the subwoofer integrated receiver. • Depending on your installation environment, connections to external components can be done before installing this system. We recommend that you temporarily place and arrange all components in order to decide which procedure is best done first. • Set the distance between the speakers to increase surround effect. (☞ P. 20) Placing the speakers You can place the speakers on a rack or attach it to a wall. Select an installation method that suits your environment. ■ Placing the speakers using the stands You can place the speakers in an upright position or a horizontal position. When placing the speakers in an upright position When placing the speakers in a horizontal position Place the speaker on the stand vertically, and then secure it with the screw as shown in the illustration below. Place the speaker on the stand horizontally, and then secure it with the screw as shown in the illustration below. 8 En Placing ■ Attaching the speakers to a wall Installing the speakers using the keyholes You can attach the speakers to a wall using commercially available screws (#8, Diameter: 7 to 9 mm (1/4” to 3/8”)). 1 When placing the speakers on a wall, remove the stands. 2 Install screws on a wall as shown in the • Do not attach the speakers to a wall that is made of weak materials such as plaster or veneered woods. Doing so may cause the speakers to fall. • Use commercially available screws that can support the weight of the installation. • Make sure you use specified screws to attach the speakers. Using clamps other than specified screws, such as short screws, nails, or two-sided tape, may cause the speakers to fall. • When connecting the speakers, fix the speaker cables in place where they will not become loose. If your foot or hand accidentally gets caught on a loose speaker cable, the speakers may fall. • After attaching the speakers, check that the speakers are fixed securely. Yamaha will bear no responsibility for any accidents caused by improper installations. illustration. The distance between the screws: 150 mm (5-7/8”) for both sides 3 Hang the speakers on the screws using the keyholes on the back of the speakers. Wall/wall support Diameter: 7 to 9 mm (#8, 1/4” to 3/8”) 6 mm Vertical (1/4”) Minimum 20 mm (3/4”) 150 mm (5-7/8”) Horizontal 150 mm (5-7/8”) 9 En PREPARATION When installing the speakers on a wall, all installation work must be performed by a qualified contractor or dealer. The customer must never attempt to perform this installation work. Improper or inadequate installation could cause the speakers to fall, resulting in personal injury. Notes Connection • Do not connect the power cable until all connections are completed. • Do not use excessive force when inserting the cable plug. Doing so may damage the cable plug and/ or terminal. Overview Follow the procedure below to connect the subwoofer integrated receiver and the external components. Indoor FM antenna (supplied) Twist and pull off the insulation tube on the lead wire. Insert to the terminal of the correct polarity—positive (+) to positive (+), and negative (–) to negative (–). White y If the radio wave reception is weak in your area or you want to improve the radio wave reception, we recommend that you use an outdoor antenna. For details, consult your nearest authorized Yamaha dealer or Service Center. Gray See “Using optional equipment”. (☞ P. 16) VCR, etc. Front Right Speaker Front Left Speaker To AC wall outlet y After you have made all connections, connect the power cable of the subwoofer integrated receiver. See “Connecting Blu-ray disc player or set-top box”. (☞ P. 11) See “Connecting a TV”. (☞ P. 11) y Connect your speaker as the center speaker of this system to the SPEAKERS receiver. (☞ P. 20) 10 En terminal of the subwoofer integrated Connection Connecting a TV If a DVD player, etc., is connected to one of the HDMI IN jacks, connect your TV or video monitor (projector, etc.) to the HDMI OUT jack of the subwoofer integrated receiver. To output the sound of a TV from this system, you can select optical digital input and connect to digital output jack. PREPARATION TV Signal flow y For analog connection, you need to connect an audio cable to the analog input terminal. Connecting Blu-ray disc player or set-top box You can connect external components with HDMI output. You can select from HDMI IN 1, 2, or 3. These three jacks are identical. Blu-ray disc player or set-top box 11 En BASIC OPERATION Basic playback operation Once you have finished all cable connections and remote control operation, follow the procedure below to start basic playback operation. 1 2 2 Press one of the input buttons to select an input source. 3 Start playback on the selected external component. For information on the external component, refer to the instruction manual for the product. 4 Press VOLUME +/– to adjust the volume level. y To turn off the volume temporarily, press MUTE. While the mute function is activated, the VOLUME indicator flashes. To resume the volume, press MUTE again or press VOLUME +/–. 4 Note When sound of HDMI is output from the TV, the volume level does not change if you press VOLUME +/–. Press again to set the system to standby mode. 1 Press . This system is turned on and the STATUS indicator lights green. When the “HDMI CONTROL” is set to “ON”, the STATUS indicator lights red. When the “HDMI CONTROL” is set to “OFF”, the STATUS indicator turns off. (☞ P. 19) y This system has the auto-sleep function, which will automatically switch the system to turn off if the system is left turned on for 24 hours without any operation being performed. ■ Using the remote control Use the remote control within 6 m (20’) of the subwoofer integrated receiver and point it toward the remote control sensor. Notes • Be careful not to spill liquid on the remote control. • Be careful not to drop the remote control. • Do not leave the remote control in a place that is: – hot or humid, such as near a heater or in a bathroom – extremely cold – dusty 12 En Within 6 m (20’) Enjoying sound modes STEREO MODE SURROUND MODE Surround mode UNIVOLUME Stereo mode An extended sound is achieved for a 2 channel source such as a CD player. Press SURROUND MODE to set surround mode. Press STEREO MODE to enter extended stereo mode. Press SURROUND MODE repeatedly until desired mode appears in the front panel display. Each time you press STEREO MODE, the function is turned on (EXTENDED STEREO) and off (STEREO) alternately. Surround mode descriptions “STEREO”: Reproduces the sound without any effect. “EXTENDED STEREO”: Reproduces a wider stereo image. MOVIE This mode is useful when you enjoy movie contents on media such as Blu-ray disc, etc. MUSIC This mode is useful when you listen to music contents on media such as Blu-ray disc, etc. SPORTS This mode is useful when you enjoy sports programs or TV news. GAME This mode is useful when you enjoy video games. y The system automatically memorizes the settings assigned to each input source. When you select another input, the system automatically recalls the last settings for the selected input. y • The default setting is “EXTENDED STEREO”. • The system memorizes the settings assigned to each input source. UniVolume™ While watching TV, use this function when you feel uncomfortable with the difference in volume between channels, TV programs, and commercials to keep the volume at an even level. Press UNIVOLUME to activate or deactivate the function. When UniVolume is activated, UNIVOLUME indicator is displayed and the sound volume of TV is uniformed. y • The system memorizes the setting assigned to each input source. • When the input source is DOCK and UniVolume is activated, compressed music enhancer function is invalid (ENHANCER indicator disappears). 13 En BASIC OPERATION You can enjoy a realistic sound effect using Yamaha’s exclusive AIR SURROUND XTREME. Listening to FM broadcasts Basic tuning operation FM INFO Sets the input to FM. Selects the information displayed in the front panel display. MEMORY PRESET Stores preset stations manually. TUNING / Select the preset FM stations. / Cursor in OPTION menu Press to change the frequency by 1 step, or press and hold to search stations automatically. RETURN OPTION Returns to the previous menu or cancels the operation. Enters OPTION menu when the input is set to FM. Editing the preset FM station ■ Automatic preset You can store up to 40 FM stations (01 to 40). 1 Press OPTION to enter OPTION menu. “AUTO PRESET” appears firstly in the front panel display. 2 Press (Center). y Press PRESET / repeatedly to select a preset number to which the first station will be stored. After approximately 5 seconds, automatic presetting starts from the lowest frequency and proceeds through higher frequencies. When the frequency is stored, the TUNED indicator lights up. 14 En When automatic preset tuning is completed, the front panel display shows message “Preset Complete” for three seconds firstly and returns to OPTION menu secondly. y Press RETURN while searching automatically, automatic preset is stopped. Notes • Any stored station data existing under a preset number is cleared when you store a new station under the same preset number. • If the number of received stations does not reach 40, automatic preset tuning automatically stops after searching for all the available stations. • Only the station with strong signals can be stored. If the desired station is not stored, or a station is not stored to the desired preset number, preset the station manually. (☞ P. 15) Listening to FM broadcasts ■ Manual station preset Use this feature to preset your desired station manually. 1 Tune into a radio station you want to preset. 2 Press MEMORY. “MANUAL PRESET” appears in the front panel display, followed soon by the preset number to which the station will be registered. y By pressing down MEMORY for more than 2 seconds. The station is registered to the lowest empty preset number or a preset number one higher than the last preset number. 3 Press PRESET When the signal of the desired FM station is too weak, set the reception mode to “MONO” to increase signal quality. 1 Press OPTION to enter OPTION menu. 2 Display “STEREO/MONO” by using the cursor and press (Center). 3 Select “MONO” to set the reception mode to monaural by using the cursor / . ■ Switching the information display Each time you press INFO, the information display changes as follows: Europe and Russia models only y To cancel registration, press RETURN on the remote control or leave the tuner without any operations for about 30 seconds. 4 Press MEMORY again to register. ■ Clearing the preset station 1 Press OPTION to enter OPTION menu. 2 Display “CLEAR PRESET” using the cursor and press (Center). Preset number and the frequency appears in the display. y You can cancel the operation and return to OPTION menu by pressing RETURN on the remote control. Information type • SURROUND MODE Displays the surround mode or stereo mode. • FREQUENCY Displays the frequency and preset number. • PROGRAM SERVICE (PS) Displays the currently received Radio Data System program. • PROGRAM TYPE (PTY) Displays the type of the currently received Radio Data System program. • RADIO TEXT (RT) Displays the information of the currently received Radio Data System program. • CLOCK TIME (CT) Displays the current time. 3 Select the preset number of the registered station you want to clear using the cursor / and press (Center). The preset station registered to the selected preset number is cleared. To clear the registration of multiple preset numbers, repeat the above steps. To end the operation, press OPTION. 15 En BASIC OPERATION / to select the preset number (01 to 40) to which the station will be registered. When you select a preset number to which no station is registered, EMPTY indicator appears on the display. When you select a registered preset number, a registered frequency is displayed on the right of the preset number. ■ Using the monaural reception mode Using optional equipment This system is equipped with a DOCK terminal, which allows you to connect a Yamaha iPod universal dock (such as YDS-11, sold separately) or a Yamaha Bluetooth wireless audio receiver (such as YBA-10, sold separately) to enjoy music contents stored in your Bluetooth component (such as a portable music player or computer equipped with Bluetooth transmitter, etc.). Connect this equipment to the DOCK terminal of the subwoofer integrated receiver using its dedicated cable. y When DOCK is selected as the input source, compressed music enhancer function is activated automatically and enhances your listening experience by regenerating the missing harmonics in a compressed music format such as MP3. Connecting dock Yamaha iPod universal dock (such as YDS-11, sold separately) Yamaha Bluetooth wireless audio receiver (such as YBA-10, sold separately) Connect either component. Using iPod™ Once you have stationed your iPod in the Yamaha iPod universal dock connected to the DOCK terminal of the subwoofer integrated receiver, you can enjoy playback of your iPod. Supported iPod iPod (Click and Wheel including iPod classic) iPod nano iPod mini iPod touch Battery charge feature This system charges the battery of an iPod stationed in the Yamaha iPod universal dock connected to the DOCK terminal of the subwoofer integrated receiver, even when this system is turned off. “Charging” appears in the front panel display. Notes • Some features may not be available depending on the model or the software version of your iPod. • For a complete list of status messages that appear in the front panel display, see the “iPod” section in “Troubleshooting” (☞ P. 24). • Be sure to set the volume to minimum before docking or removing your iPod. • To playback an iPod, select DOCK for input source. • Refer to the instruction manual of your Yamaha iPod universal dock for details. 16 En Using optional equipment Using Bluetooth™ components ■ Pairing About “Pairing” Pairing must be performed before using a Bluetooth component with the Yamaha Bluetooth wireless audio receiver connected to the system for the first time or if the registered pairing data has been deleted. “Pairing” refers to the operation of registering a Bluetooth component for Bluetooth communications. y To ensure security, a time limit of 8 minutes is set for the pairing operation. Please read and fully understand all the instructions before starting. For details, refer to the instruction manual of Yamaha Bluetooth wireless audio receiver. 1 Press DOCK to set the input to DOCK. 2 Turn on the Bluetooth component you want to pair with, and then enter pairing mode. Refer to the instruction manual of your Bluetooth component for details. 3 Press OPTION. OPTION menu for DOCK input appears in the display. 4 Press the cursor to select “PAIRING” and press (Center). “Searching...” appears when the pairing starts. While the Yamaha Bluetooth wireless audio receiver is in pairing mode, the DOCK indicator flashes in the front panel display. y audio receiver in the device list of the Bluetooth component, and then enter the pass key “0000” on the Bluetooth component. ■ Establishing a connection After the pairing is completed, perform the connecting operation on the system or on the Bluetooth component to enable communication between them. The connecting operation on the system is only available for the most recently connected Bluetooth component. 1 Press DOCK to set the input to DOCK. 2 Press OPTION to enter OPTION menu. “CONNECT” appears firstly in the front panel display. 3 Press (Center). “Searching...” appears firstly in the front panel display. When the system finds the last connected Bluetooth component, “BT connected” appears in the front panel display for 3 seconds. y • If the system cannot find the last connected Bluetooth component, “Not found” appears in the front panel display. • If you want to establish a connection with a Bluetooth component other than the one most recently connected to, connect from that Bluetooth component. Refer to the instruction manual of your Bluetooth component for details. Note To disconnect the Bluetooth wireless audio receiver from the Bluetooth component, display OPTION menu again, select “Disconnected,” and press (Center). To cancel pairing, press RETURN. 5 Check that the Bluetooth component detects the Yamaha Bluetooth wireless audio receiver. If the Bluetooth component detects the Yamaha Bluetooth wireless audio receiver, the audio receiver name (“YBA-10 YAMAHA” for example) appears in the device list of the Bluetooth component. 17 En BASIC OPERATION Note 6 Select the Yamaha Bluetooth wireless USEFUL OPERATION Setup menu Overview ■ Setup menu list Item Description of function Page 1: SW LEVEL Adjusting the volume balance during playback ☞ P. 19 Adjusting high/low frequency sound (tone control) ☞ P. 19 6: AUDIO DELAY Adjusting the audio delay ☞ P. 19 7: HDMI AUDIO Setting the audio output ☞ P. 19 8: HDMI CONTROL Switching on/off the HDMI control function ☞ P. 19 9: DISPLAY MODE Changing the brightness of the front panel display ☞ P. 20 10: SP TYPE Changing the setting of the speaker type ☞ P. 20 11: SP DISTANCE Setting the distance between the speakers ☞ P. 20 2: CENTER LEVEL 3: SUR. LEVEL 4: TONE BASS 5: TONE TREBLE Basic procedure You can change various settings of this system using the setup menu. 1 Press SETUP to enter the setup menu. “SW LEVEL” is displayed in the front panel display. 1, 4 2 Press the cursor 2, 3 3 Press the cursor / to select menu and press (Center). The current setting is displayed. / value of each menu. Press and hold the cursor setting value faster. to adjust the / to change the 4 Press SETUP again to exit the setup menu. y Press RETURN to return to the previous menu. Note If you do not operate within 30 seconds after entering the setup menu, the system automatically exits the setup menu. 18 En Setup menu Adjusting the volume balance during playback You can adjust the volume balance of the virtual speakers and subwoofer. Parameter “SW LEVEL”: Adjusts the output level of the subwoofer channel. “CENTER LEVEL”: Adjusts the output level of the virtual center speaker channel. “SUR. LEVEL”: Adjusts the output level of the surround/surround back virtual speaker channels. Adjustable range –6 to +6 (Default setting: 0) y • You can also adjust the output level of the subwoofer by pressing SUBWOOFER +/–. • If surround mode is off, the virtual center speaker and virtual surround effects become invalid. Adjusting high/low frequency sound (tone control) Parameter “TONE BASS”: Adjusts the balance of the low frequency range (Bass) of sounds output from the speaker. “TONE TREBLE”: Adjusts the balance of the high frequency range (Treble) of sounds output from the speaker. Adjustable range –6 to +6 (Default setting: 0) The system memorizes the settings assigned to each input source. Setting the audio output You can select this system (or a TV connected to this system via the HDMI OUT jack of this system) for reproducing sound signals input from the HDMI IN jack in the setup menu. Parameter “HDMI AUDIO” Adjustable option (Default setting: “AMP”) “AMP”: Outputs HDMI sound signals from the speakers connected to this system. “TV”: Outputs HDMI sound signals from the speakers of a TV connected to this system. Sound output from the speakers connected to this system is muted. Notes • The volume level will not change from pressing VOLUME +/– or MUTE while output from the TV. • You cannot change the audio output when “HDMI CONTROL” is set to “ON”. Switching on/off the HDMI™ control function You can set whether to use the HDMI control function. Refer to P.21 for HDMI control function. Parameter “HDMI CONTROL” Adjustable option (Default setting: “OFF”) “ON”: Activates the HDMI control function. “OFF”: Deactivates the HDMI control function. Adjusting the audio delay Flat panel display TV images sometimes lag behind the sound. You can use this function to delay the sound output to synchronize it with the video image. Parameter “AUDIO DELAY” Adjustable range (Default setting: “AUTO”) “AUTO”, 0 to 240 ms (You can adjust the delay time by the 10 ms.) * “AUTO”: If you operate HDMI connection to a TV with the function to automatically adjusting the audio delay, you can adjust the delay time automatically. 19 En USEFUL OPERATION You can adjust the balance of the high frequency range (Treble) and low frequency range (Bass) of sounds output from the front speakers to obtain desired tone. Note Setup menu Changing the brightness of the front panel display Setting the distance between the speakers You can change the brightness of the front panel display. You can also turn off the front panel display to view a movie in a darker environment. Select a parameter suited for the distance between the front left and right speakers, to obtain the most suitable surround effect. The brightness of the front panel changes as follows. Parameter “SP DISTANCE” Parameter “DISPLAY MODE” Adjustable range (Default setting: “DIMMER 0”) Bright Adjustable range (Default setting: “NORMAL”) “WIDE”: When the distance between the front speakers is over 150 cm (59-1/16”). “NORMAL”: When the distance between the front speakers is from 80 cm (31-1/2”) to 150 cm (59-1/ 16”). “NARROW”: When the distance between the front speakers is within 80 cm (31-1/2”). Note When the surround mode is off, this function is invalid. Dark * Selecting DISPLAY OFF turns off the front panel display after exiting the setup menu. Notes • The front panel display lights up momentarily when any operation is performed with DISPLAY OFF mode selected. • Only the STATUS indicator remains lit in DISPLAY OFF mode. Changing the setting of the speaker type You can set the speaker type if you want to add or change speakers. When you connect only the supplied speaker, you do not have to change the setting. Parameter “SP TYPE” Adjustable range (Default setting: “2CH”) “BAR”: When you connect a speaker with integrated front left/right/center channels (such as a bar-type speaker). “2CH”: When you connect front left/right (2-channel) speakers. “3CH”: When you connect front left/right (2-channel) speakers and a center speaker. Notes • To activate “SP TYPE”, set the system to standby mode and turn on again after setting the speaker type. • “SP DISTANCE” is displayed when “2CH” or “3CH” is selected. 20 En Setup menu Using the HDMI™ control function You can operate the following functions of this system with the remote control of your TV when the TV (HDMI control function supported) is connected to the HDMI OUT jack of this system. • Turning this system on or to standby mode (conjunction with TV) • Adjusting the volume • Selecting a device to reproduce TV sounds (this unit or TV) y disc or DVD player) as the input source of this system to check the video input. 7 Check if the HDMI control function works (turn on this system or adjust the volume level using the remote control of the TV). Note In case the HDMI control function does not work, check the followings. Also turning off (unplug) and turning on (plug) the TV may be effective. – The TV is connected to the HDMI OUT jack of this system. – “HDMI CONTROL” is set to “ON” on this system. – The HDMI control function is enabled on the TV. When “HDMI CONTROL” is set to “ON”, even if you press , the system will not be completely turned off and the signal from HDMI input terminal to HDMI output terminal is output. y • The STATUS indicator in the front panel display lights red when “HDMI CONTROL” is set to “ON” and the system is in standby mode. • Before pressing , select desired input sources connected to HDMI input (HDMI IN 1 to 3). USEFUL OPERATION • Even if your TV supports the HDMI control function, some functions may not be available. For details, refer to the instruction manual supplied with your TV. • If you connect this system and Blu-ray disc player or DVD player (HDMI control function supported) to HDMI, you can also control those devices with the HDMI control function. For details, refer to the instruction manual supplied with each device. • We suggest that you use products (TV, Blu-ray disc/DVD player, etc.) from the same manufacturer. • The HDMI control-compatible components include Panasonic VIERA Link compatible TV, DVD player/ recorder and Blu-ray disc player. • When “HDMI CONTROL” is set to “ON”, operations of the TV (for example, changing channels, etc.) may change the system settings, such as the surround mode. 6 Select the HDMI control device (Blu-ray (Steps 1 through 3 are required for the HDMI control function setup.) 1 Turn on all devices connected to this system with HDMI. 2 Enable the HDMI control function on each device. For this system, set “HDMI CONTROL” to “ON” (☞ P. 19). For external devices, refer to the instruction manual supplied with each device. 3 Turn off the TV, and then turn it on again. (Step 4 through 6 are required for making the TV learn linked devices. If the connections or devices are switched, you need to carry out these steps again.) 4 Select this system as the input source of the TV. 5 Turn on the HDMI control device (Blu-ray disc or DVD player) connected to this system. 21 En ADDITIONAL INFORMATION Additional information Troubleshooting If there is any problem with the system, check the following items. If you cannot solve a problem with the following remedies, or if the problem is not listed below, turn off and unplug the system, and then consult your nearest authorized Yamaha dealer or Service Center. Solution See page The power cable may be connected improperly. Make sure the power cable is plugged into the outlet firmly. 10 A speaker cable may be shorted. Make sure all speaker cables are connected properly. 10 This system may have received a strong electrical shock, such as from a lightening bolt or excessive static electricity. Set this system to standby mode, and then disconnect the power cable. Wait for about 30 seconds, connect the power cable, and then turn the system on again. 12 The volume may be set to minimum level. Adjust the volume level. The mute function may be activated. Cancel the mute function. 12 The input source or input setting may be incorrect. Select the correct input source or input setting. 12 The cables may be connected improperly. Make sure all cables are connected properly. 10 “HDMI AUDIO” in the setup menu is set to “TV”. Set “HDMI AUDIO” in the setup menu to “AMP”. 19 Sound is too low on one side. The cables may be connected improperly. Make sure all cables are connected properly. 10 Speaker channels other than the front ones make no sound. You may be listening to stereo sounds without surround mode. Press a surround mode button to enable the sound field effect. 13 “SUR. LEVEL” in the setup menu is set to minimum level. Adjust “SUR. LEVEL” in the setup menu. The volume of the subwoofer channel may be set to minimum level. Adjust the volume level of the subwoofer. Problem Power turns on but immediately shuts off. The speakers make no sound. The subwoofer makes no sound. Cause 12, 19 19 7, 19 The source does not contain lowfrequency signals. The volume level decreases without any operation. You turned off the system when the volume level was over 70. The volume level is automatically set to 70 the next time you turn on the system to protect the speakers. — Sound is poor (noisy). A speaker cable may be shorted. Make sure all cables are connected properly. 10 This system does not operate properly. This system may receive a strong electrical shock, such as from a lightening bolt or excessive static electricity, or drop in power supply. Set this system to standby mode, and then disconnect the power cable. Wait for about 30 seconds, connect the power cable, and then turn on this system. 12 A digital or highfrequency equipment produces noises. The system may be placed close to digital equipment or high-frequency equipment. Place this system farther away from such equipment. 22 En — Additional information Problem The system settings change automatically. The remote control does not operate the system. Cause Solution When “HDMI CONTROL” is set to “ON”, operations of the TV (for example, changing channels, etc.) may change the system settings, such as the surround mode. Set “HDMI CONTROL” to “OFF” or set the system again by using its remote control. The system may be outside the remote control operation range. For information on the remote control operation range, refer to “Using the remote control”. The remote control sensor of this system may be exposed to direct sunlight or lighting. Change the lighting. The batteries may be worn out. Replace the batteries. See page 21 12 — 4 ■ HDMI Problem Cause Solution See page “AUTO” set in the setup menu “AUDIO DELAY” does not operate. The TV does not support automatically adjusting the audio delay. Adjust the delay time manually (0 to 240 ms). The HDMI control function does not operate properly. The number of the connected HDMI components is over the limit. Disconnect some of the HDMI components. — No picture or sound The connected HDMI component does not support high-bandwidth digital copyright protection (HDCP). Connect the HDMI component that supports HDCP. — 19 ■ Tuner Cause FM stereo reception is noisy. The characteristics of FM stereo broadcasts may cause this problem when the transmitter is too far away, or if the antenna quality is poor. There is distortion, and clear reception cannot be obtained, even with a good FM antenna. There is multi-path interference. The desired station cannot be tuned into with the automatic tuning method. The signal is too weak. Solution See page Check the antenna connections. 10 Try using a high-quality directional FM antenna. — Set the reception mode to “MONO”. 15 Adjust the antenna position to eliminate multi-path interference. Use a high-quality directional FM antenna. Set the reception mode to “MONO” and press TUNING / to change frequency by 1 step. — — 14, 15 23 En ADDITIONAL INFORMATION Problem Additional information ■ iPod Status message Unknown iPod Cause The iPod being used is not supported by this system. iPod connected Your iPod is properly stationed in the Yamaha iPod universal dock (such as YDS-11, sold separately) connected to the DOCK terminal of this system, and the connection between your iPod and this system is completed. Disconnected Your iPod was removed from the Yamaha iPod universal dock (such as YDS-11, sold separately) connected to the DOCK terminal of this system. Charging Solution See page Only iPod (Click and Wheel including iPod classic), iPod nano, iPod mini, and iPod touch are supported. — Station your iPod back in the Yamaha iPod universal dock (YDS-11, sold separately) connected to the DOCK terminal of this system. 16 Solution See page Your iPod is charging. ■ Bluetooth Status message Searching... Cause The Yamaha Bluetooth wireless audio receiver (such as YBA-10, sold separately) and the Bluetooth component are in the process of the pairing. The Yamaha Bluetooth wireless audio receiver (such as YBA-10, sold separately) and the Bluetooth component are in the process of establishing the connection. Completed The pairing is completed. Canceled The pairing is canceled. Not found The system cannot find the Bluetooth component while performing the pairing or trying to connect to the Bluetooth component. BT connected The connection between the Yamaha Bluetooth wireless audio receiver (such as YBA-10, sold separately) and the Bluetooth component is established. Disconnected The Bluetooth component is disconnected from the Yamaha Bluetooth wireless audio receiver (such as YBA-10, sold separately). Not Available The pairing is performed when the Yamaha Bluetooth wireless audio receiver (such as YBA-10, sold separately) is connected to the Bluetooth component. 24 En Perform the pairing when the Yamaha Bluetooth wireless audio receiver (such as YBA-10, sold separately) is not connected to the Bluetooth component. 17 Additional information Glossary ■ AIR SURROUND XTREME ■ Channel (ch) This system employs new technologies and algorithms that make it possible to achieve 7-channel surround sound with only front speakers, and without using wall reflections. A channel is an audio type that has been divided based on range and other characteristics. Ex. 7.1 channel • Front speakers, Left (1ch), Right (1ch) • Center speaker (1ch) • Surround speakers, Left (1ch), Right (1ch) • Surround back speakers, Left (1ch), Right (1ch) • Subwoofer (1ch × 0.1* = 0.1ch) Ordinarily, two front speakers, a center speaker, two surround speakers, and a subwoofer are necessary for enjoying 5.1 channel surround sound. Typical 5.1 channel speaker system * In contrast to a full 1-channel band, a component designed to enhance low frequency sound for added effect. ■ Deep Color Front speakers Subwoofer Center speaker Surround speakers Virtual 7.1 channel The AIR SURROUND XTREME technology, using only front speakers and subwoofer, enables you to enjoy a realistic 7.1 channel sound by simulating sound from virtual speakers at center, surround, and surround backs. The sound image of the system Deep Color refers to the use of various color depths in displays, up from the 24-bit depths in previous versions of the HDMI specification. This extra bit depth allows HDTVs and other displays go from millions of colors to billions of colors and eliminate on-screen color banding for smooth tonal transitions and subtle gradations between colors. The increased contrast ratio can represent many times more shades of gray between black and white. Also Deep Color increases the number of available colors within the boundaries defined by the RGB or YCbCr color space. ■ Dolby Digital The system creates the virtual 7.1 channel surround sound with the subwoofer integrated receiver and the speaker. C: Center speaker FR, FL: Front speakers SW: Subwoofer SR, SL: Surround virtual speakers SBR, SBL: Surround back virtual speakers 25 En ADDITIONAL INFORMATION Digital surround sound system which is developed by Dolby Laboratories provides completely independent multi-channel audio. With 3 front channels (left, center, and right) and 2 surround stereo channels, Dolby Digital provides five full-range audio channels. With an additional channel especially for bass effects (called LFE, or low frequency effect), the system has a total of 5.1 channels (LFE is counted as 0.1 channel). By using 2 channel stereo for the surround speakers, more accurate moving sound effects and surround sound environment are possible than with Dolby Surround. Additional information ■ Dolby Pro Logic II ■ x.v.Color It is an improved matrix decoding technology that provides better spatiality and directionality on Dolby Surround programmed material; provides a convincing three-dimensional sound field on conventional stereo music recordings; and is ideally suited to bring the surround experience to automotive sound. While conventional surround programming is fully compatible with Dolby Pro Logic II decoders, soundtracks will be able to be encoded specifically to take full advantage of Pro Logic II playback, including separate left and right surround channels. A color space standard supported by HDMI version 1.3. It is a more extensive color space than sRGB, and allows the expression of colors that could not be expressed before. While remaining compatible with the color gamut of sRGB standards, “x.v.Color” expands the color space and can thus produce more vivid, natural images. It is particularly effective for still pictures and computer graphics. ■ DTS Digital surround sound system developed by DTS, Inc., which provides 5.1 channel audio. With an abundance of audio data, it is able to provide authentic-sounding effects. ■ HDMI HDMI (High-Definition Multimedia Interface) is the first industrysupported, uncompressed, all-digital audio/video interface. Providing an interface between any source (such as a set-top box or AV receiver) and an audio/video monitor (such as a digital television), HDMI supports standard, enhanced or high-definition video as well as multichannel digital audio using a single cable. HDMI transmits all ATSC HDTV standards and supports 8 channel digital audio, with bandwidth to spare to accommodate future enhancements and requirements. When used in combination with HDCP (High-bandwidth Digital Content Protection), HDMI provides a secure audio/ video interface that meets the security requirements of content providers and system operators. For further information on HDMI, visit the HDMI website at “http://www.hdmi.org/.” ■ PCM (Pulse Code Modulation) A signal that is changed to digital format without compression. A CD is recorded with 16-bit sound at 44.1 kHz, while DVD recording is anywhere from 16 bits at 48 kHz to 24 bits at 192 kHz, which makes it a higher quality sound than CD. ■ Sampling frequency The number of sampling (process for digitalizing analog signals) per second. In principle, the higher the sampling rate, the wider the frequency range that can be played back, and the higher the quantized bit rate, the finer the sound that can be reproduced. 26 En Additional information Specifications ■ SR-300 GENERAL AUDIO SECTION • Power Supply [U.S.A. and Canada models] .......... AC120 V, 60 Hz [Other models] .................... AC220-240 V, 50/60 Hz • Power Consumption...........................................35 W • Standby Power Consumption [U.S.A. and Canada models] ............. less than 0.4 W [Other models] ................................... less than 0.5 W • Dimensions (W × H × D) .........435 × 151 × 361 mm (17-1/8 × 6 × 14-1/4 in) • Weight...............................................................8.6 kg • Minimum RMS Output Power Front Left and Right (1 kHz, 1% THD, 6 Ω) ................................................................ 45 W+45 W Center (1 kHz, 1% THD, 6 Ω) .......................... 45 W Subwoofer (100 Hz, 1% THD, 3 Ω) ................. 90 W • Maximum Power Front Left and Right (1 kHz, 10% THD, 6 Ω) ................................................................ 50 W+50 W Center (1 kHz, 10% THD, 6 Ω) ........................ 50 W Subwoofer (100 Hz, 10% THD, 3 Ω) ............. 100 W FM SECTION • Tuning Range [U.S.A. and Canada models]........ 87.5 to 107.9 MHz [Other models] ......................... 87.50 to 108.00 MHz • Frequency Step [U.S.A. and Canada models].........................200 kHz [Other models] ................................................50 kHz Antenna Input (unbalanced)............................... 75 Ω SUBWOOFER SECTION • Type ................................................. Bass reflex type Non-magnetic shielding type • Driver .......................................13 cm (5-1/4 in) cone • Frequency Response ........................35 Hz to 150 Hz • Impedance ............................................................ 3 Ω This system employs new technologies and algorithms that make it possible to achieve 7-channel surround sound with only two front speakers, and without using wall reflections. “DTS” and “DTS Digital Surround” are registered trademarks of DTS, Inc. • Type ...................... 2 way Accoustic suspension type Non-magnetic shielding type • Driver Woofer ..............................6.5 cm (2-1/2 in) cone × 2 Tweeter .......... 2.5 cm (1 in) Balanced dome type × 1 • Frequency Response ...................... 150 Hz to 20 kHz • Impedance............................................................ 6 Ω • Dimensions (W × H × D) NS-B380 .....................................90 × 220 × 109 mm (3-1/2 × 8-5/8 × 4-1/4 in) Stand .............................................87 × 63 × 120 mm (3-3/8 × 2-1/2 × 4-3/4 in) • Weight...............................................................1.0 kg * Specifications are subject to change without notice. Bluetooth™ Bluetooth is a registered trademark of Bluetooth SIG and is used by Yamaha in accordance with a license agreement. “HDMI,” the “HDMI” logo and “High-Definition Multimedia Interface” are trademarks, or registered trademarks of HDMI Licensing LLC. x.v.Color™ “x.v.Color” is a trademark of Sony Corporation. “UniVolume” is a trademark of Yamaha Corporation. iPod™ “iPod” is a trademark of Apple Inc., registered in the U.S. and other countries. 27 En ADDITIONAL INFORMATION Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. ■ NS-B380 Additional information Available signal information ■ HDMI signal compatibility Audio signals Audio signal types Audio signal formats Compatible media 2ch Linear PCM 2ch, 32-96 kHz, 16/20/24 bit CD, DVD-Video, DVD-Audio, etc. Multi-ch Linear PCM 8ch, 32-96 kHz, 16/20/24 bit DVD-Audio, Blu-ray disc, HD DVD, etc. Bitstream Dolby Digital, DTS DVD-Video, etc. y • Refer to the supplied instruction manuals of the input source component, and set the component appropriately. • When CPPM copy-protected DVD-Audio is played back, video and audio signals may not be output depending on the type of the DVD player. • This unit is not compatible with HDCP-incompatible HDMI or DVI components. • To decode audio bitstream signals on this unit, set the input source component appropriately so that the component outputs the bitstream audio signals directly (does not decode the bitstream signals on the component). Refer to the supplied instruction manuals for details. Video signals This unit is compatible with the video signals of the following resolutions: • 480i/60 Hz • 576i/50 Hz • 480p/60 Hz • 576p/50 Hz • 720p/60 Hz, 50 Hz • 1080i/60 Hz, 50 Hz • 1080p/60 Hz, 50 Hz, 24 Hz 28 En YC173A0/OMEN2
1 / 1

Yamaha YHT-S300 El manual del propietario

Categoría
Receptor
Tipo
El manual del propietario