769-19330 / 01 02/20

2-CYCLE GAS BRUSHCUTTER / TRIMMER

DESMALEZADORA / DESBROZADORA DE GAS DE 2 TIEMPOS

OPERATOR’S MANUAL | MANUAL DEL OPERADOR

1-888-331-4569 WWW.CRAFTSMAN.COM

IF YOU HAVE QUESTIONS OR COMMENTS, CONTACT US.

SI TIENE DUDAS O COMENTARIOS, CONTÁCTENOS.

WS235

CMXGTAMD27BC

TABLE OF CONTENTS

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Oil and Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Starting and Stopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Cleaning and Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

California, Maine, Oregon and Washington. All U.S. Forest Land

and the state of California (Public Resources Codes 4442 and

4443), Oregon and Washington require, by law that certain internal

combustion engines operated on forest brush and/or grass-covered

areas be equipped with a spark arrestor, maintained in effective

working order, or the engine be constructed, equipped and

maintained for the prevention of fire. Check with your state or local

authorities for regulations pertaining to these requirements. Failure

to follow these requirements could subject you to liability or a fine.

This unit is factory equipped with a spark arrestor. If it requires

This product can expose you to

chemicals including engine exhaust, which is known to the

State of California to cause cancer, and carbon monoxide,

which is known to the State of California to cause birth

defects or other reproductive harm. For more information

go to www.P65Warnings.ca.gov.

• Never allow children to operate the unit. Teens must be trained,

accompanied and supervised by an adult. Never allow adults to

operate the unit without proper instruction.

• All guards and safety attachments must be installed properly

before operating the unit.

• Inspect the unit before use. Check for damaged parts. Check for

fuel leaks. Make sure all parts operate properly. Make sure all

fasteners are in place and secure. Make sure all moving parts are

properly aligned and are not bound. Replace parts that are cracked,

chipped, or damaged in any way. Have all damaged or improperly

• Clear the area of children, bystanders and pets; keep them

outside a 50-foot (15 m) radius, at a minimum. Even then, they are

still at risk from thrown objects. Encourage bystanders to wear

eye protection. If you are approached, stop the unit immediately.

• Squeeze the throttle control and check that it returns

automatically to the idle position. Make all adjustments or

repairs before using the unit.

• Do not change the engine governor settings or overspeed the

engine.

• This unit is intended for occasional, household use only.

• Store fuel only in containers specifically designed and approved

for the storage of such materials.

• Always stop the engine and allow it to cool before filling the

tank. Never remove the fuel tank cap or add fuel when the

engine is hot. Always loosen the fuel tank cap slowly to relieve

any pressure in the tank before fueling.

• Always mix and add fuel in a clean, well-ventilated outdoor area

where there are no sparks or flames. DO NOT smoke.

• Never operate the unit without the fuel cap securely in place.

• Avoid creating a source of ignition for spilled fuel. Wipe up any

its vapors can explode if ignited. Take the following

precautions:

WHILE OPERATING

• Wear safety glasses or goggles that meet current ANSI Z87.1

standards and are marked as such. Wear ear/hearing protection

when operating this unit. Wear a face mask or dust mask if the

operation is dusty. Use a hard hat or other type of safety helmet.

• Wear heavy long pants, boots, gloves and a long sleeve shirt. Do

not wear loose clothing, jewelry, short pants, sandals or go

• Use the unit only in daylight or good artificial light.

• Avoid accidental starting. Be in the starting position whenever

pulling the starter rope. The operator and unit must be in a

stable position while starting. Refer to Starting and Stopping.

• Use the right tool. Only use this tool for its intended purpose.

Only use the unit as described in this manual.

• Always hold the unit with both hands when operating. Keep a

firm grip on both handles or grips.

• Do not overreach. Always keep proper footing and balance. Take

extra care when working on stairs, steep slopes or inclines. To

OTHER SAFETY WARNINGS

• Maintain the unit with care. Follow all maintenance instructions

Push primer bulb, fully and slowly, 10 times.

Small objects can be

propelled at high speed, causing injury.

extremely hot from operation. When turned off, they

remain hot for a short time.

the cutting head shield. To prevent serious injury, do

not touch the line cutting blade.

Sharpening the blade can cause the tip of the blade to

break off while in use. This can result in severe

enough to propel the unit and/or operator in any

direction, possibly causing a loss of control. Blade

thrust can occur without warning if the blade snags,

stalls or binds. This is more likely to occur in areas

where it is difficult to see the material being cut.

SPECIFICATIONS*

* All specifications are based on the latest product information available at the time of printing. We reserve the right to make changes at any

time without notice.

Engine Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air-Cooled, 2-Cycle

Displacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 cc (1.64 cu. in.)

Spark Plug Gap. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.025 in. (0.635 mm)

Spark Plug. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Champion® RDJ7J or equivalent plug

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel/Oil Mixture

Fuel/Oil Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40:1

APPLICATIONS

As a trimmer:

• Cutting grass and light weeds

• Edging

• Decorative trimming around trees, fences, etc.

As a brushcutter:

• Cutting weeds and light brush up to 1/2 inch (1.27 cm) in

Other optional attachments may be used with this unit.

ASSEMBLY TOOLS REQUIRED

ASSEMBLY

INSTALLING AND REMOVING THE ATTACHMENT

The coupler enables the use of various optional attachments.

Installing the Attachment

1. Remove the hanger cap from the attachment. Keep the hanger

cap for use when storing the attachment. If present, remove the

gray spacer from the coupler.

Removing the Attachment

1. Set the unit on a flat, level surface.

2. Turn the knob counterclockwise to loosen the coupler (Fig. 1).

3. Press and hold the release button (Fig. 3).

4. Pull the attachment straight out of the coupler (Fig. 2).

Before operating the unit, make sure the

release button is fully snapped into the primary hole and the

knob is securely tightened.

DECORATIVE TRIMMING (AS A TRIMMER)

When trimming around trees, posts, fences, etc., rotate the whole

unit so that the cutting head is at a 30° angle to the ground (Fig. 23).

TIPS FOR BEST RESULTS (AS A TRIMMER)

• For most operations, cut from side to side.

• To direct clippings away from the operator, tilt the cutting head

NOTE: Some line breakage will occur from:

ADJUSTING THE TRIMMING LINE LENGTH

This unit is equipped with a bump head. Trimming line can be

released from the cutting head without stopping the engine.

To release more line, lightly tap the bump knob on the ground (Fig. 22)

while operating the unit at high speed. For best results, tap the

NOTE: Always keep the trimming line fully extended. Line release

A blade in the cutting head shield will cut the line to the proper

length if any excess line is released.

Do not remove or alter the line cutting blade

EDGING (AS A TRIMMER)

The trimmer attachment can be used for edging (Fig. 24). Alternatively,

Rotating the Trimmer Attachment

the 90° edging hole (Fig. 25).

4. Turn the knob clockwise to tighten the coupler (Fig. 25).

Maintaining the Trimming Line

Hard surfaces, such as sidewalks, can cause the trimming line to

wear down quickly or break.

• Frequently check and adjust the trimming line length. Refer to

Adjusting the Trimming Line Length. Always keep the trimming

line fully extended.

• DO NOT force the unit. Make shallow cuts in as many passes as are

necessary to achieve the desired depth. Cut at a slow, even pace.

To avoid serious personal injury and

damage to the unit, shut the unit off before rotating the

attachment.

To avoid serious personal injury, always stop

the engine and allow it to cool before cleaning or maintaining

MAINTENANCE SCHEDULE

Perform these required maintenance procedures at the frequency

stated in the table. These procedures should also be a part of any

seasonal tune-up.

NOTE: Some maintenance procedures may require special tools or

skills. If you are unsure about these procedures, take the unit to

an authorized service dealer. Call 1-888-331-4569 for more

information.

NOTE: Maintenance, replacement, or repair of the emission control

devices and system may be performed by an authorized service

REPLACING THE TRIMMING LINE

Only use the trimming line described in the Specifications section.

NOTE: Always use the correct line length when installing trimming

Part 1 - Removing the Inner Reel

1. Hold the cutting head in place (Fig. 26). Turn the bump knob

NOTE: The outer spool (Fig. 27) will remain attached to the unit.

Part 2 - Winding New Trimming Line onto the Inner Reel

• If using single line, refer to Winding Single Line.

• If using split line, refer to Winding Split Line.

• If using a prewound inner reel, proceed to Part 3 - Installing the

Winding Single Line

1. Cut one 18-foot (5.5 m) length of new single trimming line. Fold

NOTE: Failure to wind the line in the direction indicated will cause

4. Insert the two 6-inch ends into the two holding slots (Fig. 30).

Winding Split Line

1. Cut one 9-foot (2.7 m) length of new split line trimming line.

2. Insert one line end through one of the two holes in the inner reel.

MAINTAINING THE AIR FILTER

Failure to maintain the air filter can result in poor performance or can

Cleaning the Air Filter

4. Lightly coat the air filter with clean SAE 30 oil.

• Allow the engine to cool before storing.

• Lock up the unit to prevent unauthorized use or damage.

• Store the unit in a dry, well-ventilated area.

• Store the unit out of the reach of children.

• To suspend the attachment from a hook, install the hanger cap

onto the attachment. Make sure the release button is securely

locked into one of the holes on the hanger cap.

Short-term Storage (1-2 weeks)

1. Store the unit in a horizontal position. If this is not possible, store

the unit vertically with the engine at the top.

drops of any high-quality motor oil or 2-cycle oil into the

cylinder. Pull the starter rope slowly to distribute the oil. Reinstall

the spark plug.

4. Thoroughly clean the unit and inspect it for any loose or

damaged parts. Repair or replace damaged parts and tighten

loose screws, nuts or bolts.

Preparing the Unit for Use after Long-term Storage

1. Remove the spark plug. Tip the unit and drain all of the oil from

the cylinder into an approved container. Reinstall the spark plug.

NOTE: Do not use fuel that has been stored for more than 30 days.

MAINTAINING THE SPARK PLUG

1. Stop the engine and allow it to cool. Grasp the spark plug boot

3. Inspect the spark plug. If the spark plug is cracked, fouled or

dirty, replace it with replacement part #753-06847, a Champion

RDJ7J or an equivalent spark plug.

4. Use a feeler gauge to set the air gap at 0.025 in. (0.635 mm)

(Fig. 36).

5. Install the spark plug in the cylinder head. Tighten the spark plug

with a 5/8-inch socket, turning it clockwise until snug.

NOTE: If using a torque wrench, torque to:

The primer bulb was not pressed enough Press the primer bulb 10 times

The engine is flooded

Press the throttle lockout, squeeze the throttle control and pull the

starter rope until the engine starts

The fuel is old (over 30 days) and/or improperly mixed Drain the fuel tank and add fresh, properly-mixed fuel

The spark plug is fouled Replace the spark plug

The choke lever was not flipped Refer to Starting Instructions in the Starting and Stopping section

TROUBLESHOOTING

The fuel is old (over 30 days) and/or improperly mixed Drain the fuel tank and add fresh, properly-mixed fuel

The cutting head is bound with grass Stop the engine and clean the cutting head

The air filter is dirty Clean or replace the air filter

The spark plug is fouled Replace the spark plug

The cutting head is bound with grass Stop the engine and clean the cutting head

The cutting head is out of line Refill the cutting head with new line

The inner reel is bound up Rewind the line

The cutting head is dirty Clean the inner reel and outer spool

The line is welded Open the cutting head and remove the welded section

The line is twisted Rewind the line

Not enough line is extended

Stop the unit, push the bump knob and pull the line until 4 inches

THE ENGINE WILL NOT IDLE

THE ENGINE WILL NOT START

WARRANTY

Limited Warranty

The limited warranty set forth herein is given by MTD LLC to the Initial Purchaser (as defined herein) with respect to new Craftsman branded

hand held product (“Product”). This limited warranty does not cover Emission Control Systems and is not a Federal Emission Control

Warranty Statement as defined by U.S. federal law. Please refer to the Federal Emission Control Warranty Statement in the operator’s manual

for warranties covering Emission Control Systems.

Scope Of The Limited Warranty

Subject to the Exclusions, the Product is warranted to be free from manufacturing defects in either workmanship or materials for the

Warranty Period. During the Warranty Period, MTD LLC will, at its option, either repair or replace any original part that is covered by this

limited warranty and is determined to be defective in workmanship or material.

To Qualify For This Limited Warranty, The Product:

1. Must have been purchased from an authorized Craftsman branded product Retailer.

2. Must have been purchased within the United States by an Initial Purchaser.

3. Must have been used only for residential or otherwise non-commercial purposes.

4. Must have been used in a manner consistent with the normal and proper intended use.

Who Can Perform Repairs Under This Warranty?

In order to qualify for the limited warranty as set forth herein, the repairs made under warranty must be performed by an authorized warranty

1. Product purchased outside of the United States.

2. Damage due to lack of maintenance and/or improper maintenance as described in the operator’s manual.

3. Normal wear and tear resulting from use of the Product.

4. Use of the Product that is not consistent with the intended use thereof, as described in the operating instructions, including, but not

limited to, abuse, misuse and/or neglect of the Product or any use inconsistent with and/or non-compliant with instructions contained in

the operator’s manual.

5. Any expendable, consumable, or routine maintenance item which needs replacement or service as part of normal maintenance, unless

such items have defects that cause failure or premature wear within the first thirty (30) days. Where applicable, normal wear items

include, but are not limited to, bump knobs, outer spools, cutting line, inner reels, starter pulleys, starter ropes, drive belts, saw chains,

guide bars, cultivator tines, filters, spark plugs, carrying cases, scabbards, or blades.

4. Damage resulting from the installation or use of any accessory or non-OEM (original equipment manufacturer) part for use with the Product.

Limitations:

1. THERE ARE NO IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR

2. THE PROVISIONS AS SET FORTH HEREIN PROVIDE THE SOLE AND EXCLUSIVE REMEDY ARISING FROM THE SALE. MTD LLC

How State Law Relates To This Warranty.

This limited warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

el derecho de hacer cambios en cualquier momento sin aviso previo.

TABLA DE CONTENIDO

de los estados de California, Maine, Oregon y Washington.

Todos los territorios de bosques de EE. UU. y los estados de

California (Códigos de Recursos Públicos 4442 y 4443), Oregon y

Washington exigen por ley, que determinados motores de

combustión interna que se operan en zonas cubiertas por malezas

de bosque y/o hierbas cuenten con un amortiguador de chispas

que se deberá mantener en condiciones de uso adecuadas o que el

motor se diseñe, equipe y mantenga para prevenir incendios.

Corrobore con las autoridades estatales o locales cuáles son las

normativas correspondientes a dichas exigencias. El

fábrica con un amortiguador de chispas. Si requiere reemplazo,

póngase en contacto con su representante local de servicio para

instalar el conjunto de silenciador adecuado.

Lea el manual del operador y siga todas las advertencias e

instrucciones de seguridad. Si no lo hace, el operador y/o los

observadores pueden sufrir lesiones graves.

Si no se cumple una advertencia de seguridad de

PELIGRO usted mismo u otras personas sufrirán lesiones

CONVERSIÓN DE LA UNIDAD DE DESBROZADORA A

Cómo quitar la cuchilla

1. Rote la cuchilla (Fig. 11) hasta que el orificio del casquillo del eje

5. Quite la varilla de seguridad (Fig. 11).

6. Retire la retención de la cuchilla y la cuchilla (Fig. 11).

Instalación del cabezal de corte

1. Rote el casquillo del eje de salida hasta que el orificio del casquillo

2. Inserte la varilla de seguridad a través de la ranura de la varilla

3. Mantenga la varilla de seguridad en su lugar sujetando el otro

6. Quite la varilla de seguridad.

7. Instale el protector del cabezal de corte. Consulte Instalación y

CONVERSIÓN DE LA UNIDAD DE RECORTADORA A

Extracción del cabezal de corte

1. Extraiga el protector del cabezal de corte. Consulte Instalación y

extremo contra el alojamiento del eje (Fig. 13).

5. Mientras sostiene la varilla de seguridad en su lugar, desatornille

el cabezal de corte girándolo en el sentido de las agujas del reloj

(Fig. 14).

6. Quite la varilla de seguridad (Fig. 14).

7. Extraiga la retención de la cuchilla (Fig. 14).

1. Rote el casquillo del eje de salida hasta que el orificio del casquillo

del eje se alinee con la ranura de la varilla de seguridad (Fig. 9).

2. Inserte la varilla de seguridad a través de la ranura de la varilla

una llave de tuercas (Fig. 16):

8. Quite la varilla de seguridad.

lleve puesto siempre guantes cuando manipule la cuchilla.

Desconecte el cable de la bujía para evitar que la unidad

INSTALACIÓN Y EXTRACCIÓN DEL PROTECTOR DEL

INSTRUCCIONES PARA LA MEZCLA DEL ACEITE Y EL

inflamable. Los vapores encendidos pueden explotar.

Detenga siempre el motor y déjelo enfriar antes de llenar el

salpicaduras de combustible. Nunca opere la unidad si la

tapa del combustible no está bien sujeta en su lugar.

aire libre, limpia y bien ventilada. Limpie de inmediato la

gasolina que se haya derramado. Evite que se genere una

fuente de encendido para el combustible derramado. No

arranque el motor hasta que se hayan disipado los

vapores del combustible.

siga estrictamente las instrucciones para la mezcla de la

gasolina y el aceite que figuran en el recipiente de aceite

de 2 ciclos. El uso de combustible que se mezcló

incorrectamente puede dañar gravemente el motor.

INSTRUCCIONES DE ARRANQUE

NOTA: Para evitar apretar el control del acelerador

NOTA: No es necesario encender la unidad. El interruptor de

Antes de hacer arrancar la unidad

Arranque de la unidad

NOTA: NO apriete el control del acelerador (Fig. 18) hasta el

1. Presione y luego suelte el bulbo del cebador lentamente

2. De vuelta la palanca del cebador en el sentido de las agujas del

3. Agacharse en la posición de arranque (Fig. 20).

4. Tire de la cuerda de arranque con un movimiento controlado y

SI... el motor ya está caliente: Oprima y mantenga el bloqueo de

Después de poner en marcha la unidad

1. Calce el pasador a presión de la correa de hombro sobre la

CÓMO SOSTENER LA UNIDAD

• Párese en la posición de arranque (Fig. 21). Párese derecho. No

se incline sobre el aparato.

• Mantenga los pies alejados y apoyados firmemente sobre el suelo.

• Sujete la empuñadura del eje con la mano derecha. Mantenga el

brazo derecho ligeramente doblado.

• Sostenga la manija con la mano izquierda. Mantenga el brazo

izquierdo bien derecho.

opere la unidad. El motor puede estar muy caliente.

RECOMENDACIONES PARA MEJORES RESULTADOS

(COMO CORTAMALEZAS)

• Mantenga la cuchilla paralela al suelo.

• Haga el corte siempre con la unidad funcionando a plena

velocidad. Esto ofrece máxima potencia de corte y hace que la

cuchilla sea menos propensa que doblarse, atascarse u ocurrir

un empuje de la cuchilla.

• Para dirigir los recortes lejos del operador, corte de izquierda a

derecha siempre que sea posible.

u otros, no use la cuchilla como un recortador de bordes.

cuchilla cuando entra en contacto con un objeto si no lo corta

de inmediato. El empuje de la cuchilla puede ser lo

suficientemente violento para ocasionar que la unidad y/o el

operador sean lanzados en cualquier dirección, y que

posiblemente se pierda el control de la unidad. El empuje de

personales graves, no toque la cuchilla mientras esté

girando por inercia.

apague siempre la unidad antes de retirar los desechos de

la misma. Deje que la cuchilla se detenga por completo.

protección ocular, auditiva, de manos, pies y corporal para

reducir el riesgo de sufrir lesiones durante la operación de

AJUSTAR LA LONGITUD DE LA LÍNEA DE CORTE

Esta unidad está equipada con un cabezal de impacto. La línea de

BORDEADO (COMO RECORTADORA)

El accesorio de la recortadora puede ser utilizado para el bordeado

MANTENIMIENTO

PLAN DE MANTENIMIENTO

Lleve a cabo los procedimientos necesarios de mantenimiento con

la frecuencia indicada en la tabla. Estos procedimientos deberán

también formar parte de cualquier ajuste de temporada.

NOTA: Los trabajos de mantenimiento, reemplazo o reparación de

los dispositivos y los sistemas de control de emisiones puede

realizarlos un distribuidor de servicio autorizado. Para más

información, llame al 1-888-331-4569.

NOTA: Para ver la lista completa de términos y la cobertura de los

dispositivos de control de emisiones como parachispas,

silenciador, carburador, etc., lea la declaración de California/

EPA que viene junto con la unidad.

FRECUENCIA MANTENIMIENTO REQUERIDA

Cada 10 horas • Limpie y vuelva a lubricar el filtro de aire.

• Si se utiliza un hilo simple, consulte Enrollado de hilo simple.

• Si se utiliza Split-Line, consulte Enrollado de Split-Line.

• Si se utiliza un carrete de hilo preenrollado, prosiga a la Parte 3 –

Instalación del carrete interior.

Enrollado del hilo simple

1. Corte un largo de 18 pies (5.5 m) de hilo de recorte simple

nuevo. Doble el hilo a la mitad para crear un lazo en el medio.

pulgadas (150 mm) de hilo. Coloque su dedo índice entre los dos

hilos para evitar que los mismos se traslapen.

NOTA: Si no se enrolla el hilo en el sentido que se indica, el cabezal

de corte funciona de manera incorrecta.

4. Inserte las dos extremos de 6 pulgadas dentro de las dos

ranuras de sujeción (Fig. 30).

Enrollado de Split-Line

1. Corte un largo de 9 pies (2.3 m) de hilo de recorte Split-Line.

2. Inserte un extremo del hilo a través de uno de los dos orificios

(150 mm).

5. Enrolle el hilo ajustado en capas parejas en la dirección que se

indica en el carrete interior.

NOTA: Si no se enrolla el hilo en el sentido que se indica, el cabezal

de corte funciona de manera incorrecta.

6. Inserte las dos extremos de 6 pulgadas dentro de las dos

ranuras de sujeción (Fig. 30).

Parte 3 – Instalación del carretel interior

1. Pase los extremos de los hilos a través de los ojales de la

ranuras de retención.

5. Mientras sujeta el carrete interior y la bobina exterior juntos,

enrosque la perilla de impacto en sentido contrario a las agujas

del reloj (Fig. 26). Ajuste firmemente la perilla de impacto.

O PEDIR SERVICIO DE REPARACIÓN