Samsung BD-J5700 Manual de usuario

Marca: Samsung

Modelo: BD-J5700

Categoría: Reproductores de Blu-Ray

Tipo: Manual de usuario

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service,

please register your product at

www.samsung.com/register

Blu-ray

™

Disc Player

user manual

BD-J5700

ENGLISH

Safety Information

Warning

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE THE COVER(OR

BACK). THERE ARE NO USER SERVICEABLE

PARTS INSIDE. REFER ALL SERVICING TO

QUALIFIED PERSONNEL.

This symbol indicates that high

voltage is present inside. It is

dangerous to make any kind of

contact with any internal part of

this product.

This symbol indicates that

important literature concerning

operation and maintenance has

been included with this product.

•

The slots and openings in the cabinet and

in the back or bottom are provided for

necessary ventilation. To ensure reliable

operation of this apparatus, and to protect it

from overheating, these slots and openings

must never be blocked or covered.

- Do not place this apparatus in a confined

space, such as a bookcase, or built-

in cabinet, unless proper ventilation is

provided.

- Do not place this apparatus near or over

a radiator or heat register, or where it is

exposed to direct sunlight.

- Do not place vessels (vases etc.)

containing water on this apparatus. A

water spill can cause a fire or electric

shock.

•

Do not expose this apparatus to rain or place

it near water (near a bathtub, washbowl,

kitchen sink, or pool, etc.). If this apparatus

accidentally gets wet, unplug it and contact

an authorized dealer immediately.

•

This apparatus uses batteries. In

your community, there might be

environmental regulations that require you

to dispose of these batteries properly.

Please contact your local authorities for

disposal or recycling information.

•

Do not overload wall outlets, extension

cords or adaptors beyond their capacity,

since this can result in fire or electric shock.

•

Route power-supply cords so that they

are not likely to be walked on or pinched

by items placed on or against them. Pay

particular attention to cords at the plug end,

at wall outlets, and the point where they exit

from the apparatus.

•

To protect this apparatus from a lightning

storm, or when it is left unattended and

unused for long periods of time, unplug

it from the wall outlet and disconnect the

antenna or cable system. This will prevent

damage to the set due to lightning and

power line surges.

•

Before connecting the AC power cord to the

DC adaptor outlet, make sure the voltage

designation of the DC adaptor corresponds

to the local electrical supply.

•

Never insert anything metallic into the open

parts of this apparatus. Doing so may create

a danger of electric shock.

•

To avoid electric shock, never touch the

inside of this apparatus. Only a qualified

technician should open this apparatus.

•

Make sure to plug the power cord in until it

is firmly seated. When unplugging the power

cord from a wall outlet, always pull on the

power cord's plug. Never unplug by pulling

on the power cord. Do not touch the power

cord with wet hands.

•

If this apparatus does not operate normally

- in particular, if there are any unusual

sounds or smells coming from it - unplug

it immediately and contact an authorized

dealer or service center.

•

Maintenance of Cabinet.

- Before connecting other components to

this product, be sure to turn them off.

- If you move your product suddenly

from a cold place to a warm place,

condensation may occur on the

operating parts and lens and cause

abnormal disc playback. If this occurs,

unplug the product, wait for two hours,

and then connect the plug to the power

outlet. Then, insert the disc, and try to

play back again.

•

Be sure to pull the power plug out of the

outlet if the product is to remain unused or

if you are leaving the house for an extended

period of time (especially when children,

elderly, or disabled people will be left alone

in the house).

- Accumulated dust can cause an electric

shock, an electric leakage, or a fire by

causing the power cord to generate

sparks and heat or the insulation to

deteriorate.

•

Contact an authorized service center for

information if you intend to install your

product in a location with heavy dust, high

or low temperatures, high humidity, chemical

substances, or where it will operate 24

hours a day such as in an airport, a train

station, etc. Failing to do so may lead to

serious damage of your product.

•

Use only a properly grounded plug and wall

outlet.

- An improper ground may cause electric

shock or equipment damage. (Class l

Equipment only.)

•

To turn this apparatus off completely, you

must disconnect it from the wall outlet.

Consequently, the wall outlet and power

plug must be readily accessible at all times.

•

Do not allow children to hang on the

product.

•

Store the accessories (battery, etc.) in a

location safely out of the reach of children.

•

Do not install the product in an unstable

location such as a shaky self, a slanted floor,

or a location exposed to vibration.

•

Do not drop or strike the product. If the

product is damaged, disconnect the power

cord and contact a service center.

•

To clean this apparatus, unplug the power

cord from the wall outlet and wipe the

product using a soft, dry cloth. Do not

use any chemicals such as wax, benzene,

alcohol, thinners, insecticide, air fresheners,

lubricants, or detergent. These chemicals

can damage the appearance of the product

or erase the printing on the product.

•

Do not expose this apparatus to dripping

or splashing. Do not put objects filled with

liquids, such as vases on the apparatus.

•

Do not dispose of batteries in a fire.

•

Do not plug multiple electric devices into the

same wall socket. Overloading a socket can

cause it to overheat, resulting in a fire.

•

There is danger of an explosion if you

replace the batteries used in the remote with

the wrong type of battery. Replace only with

the same or equivalent type.

•

WARNING - TO PREVENT

THE SPREAD OF FIRE,

KEEP CANDLES AND

OTHER ITEMS WITH OPEN

FLAMES AWAY FROM THIS

PRODUCT AT ALL TIMES.

Mexico only (only the models

described in this manual)

The operation of this device is subject on the

following two conditions : (1) it is possible

that this apparratus or device may not cause

harmful interference, and (2) this apparatus or

device must accept any interference, including

that may cause undesired operation.

FCC NOTE (for U.S.A)

This equipment has been tested and found

to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC

rules. These limits are designed to provide

reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may

cause harmful interference to radio or television

reception, which can be determined by turning

the equipment off and on.

The user is encouraged to try to correct the

interference by one or more of the following

measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the

equipment and receiver.

•

Connecting this equipment into an outlet

on a circuit different from that to which the

receiver is connected.

•

Consult the dealer or an experienced radio/

TV technician for help.

This class B digital product meets all

requirements of the Canadian Interference -

Causing Equipment Regulations.

Note to CATV system installer

This reminder is provided to call the CATV system

installer's attention to Article 820-40 of the

National Electrical Code (Section 54 of Canadian

Electrical Code, Part I) that provides guidelines

for proper grounding and, in particular, specifies

that the cable ground shall be connected to the

grounding system of the building as close to the

point of cable entry as practical.

CLASS 1 LASER PRODUCT

This Compact Disc player is classified as a

CLASS 1 LASER product. Use of controls,

adjustments or performance of procedures

other than those specified herein may result in

hazardous radiation exposure.

DANGER :

•

VISIBLE AND INVISIBLE LASER RADIATION

WHEN OPEN. AVOID DIRECT EXPOSURE

TO BEAM. (FDA 21 CFR)

CAUTION :

•

CLASS 3B VISIBLE AND INVISIBLE

LASER RADIATION WHEN OPEN. AVOID

EXPOSURE TO THE BEAM. (IEC 60825-1)

•

THIS PRODUCT UTILIZES A LASER.

USE OF CONTROLS OR ADJUSTMENTS

OR PERFORMANCE OF PROCEDURES

OTHER THAN THOSE SPECIFIED HEREIN

MAY RESULT IN HAZARDOUS RADIATION

EXPOSURE. DO NOT OPEN COVER AND

DO NOT REPAIR YOURSELF. REFER

SERVICING TO QUALIFIED PERSONNEL.

CLASS 1 LASER PRODUCT

KLASSE 1 LASER PRODUKT

LUOKAN 1 LASER LAITE

KLASS 1 LASER APPARAT

PRODUCTO LÁSER CLASE 1

✎

NOTES

If the Region number of a Blu-ray Disc/DVDs

does not correspond to the Region number of

this product, the product cannot play the disc

Precautions

Important Safety Instructions

Read these operating instructions carefully

before using the unit. Follow all the safety

instructions listed below.

Keep these operating instructions handy for

future reference.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings.

Install in accordance with the

manufacturer's instructions.

8. Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus

(including AV receivers) that produce heat.

9. Do not defeat the safety purpose of the

polarized or grounding-type plug. A polarized

plug has two blades with one wider than

the other. A grounding type plug has two

blades and a third grounding prong. The

wide blade or the third prong are provided

for your safety. If the provided plug does not

fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10 . Protect the power cord from being walked

on or pinched particularly at plugs,

convenience receptacles, and the point

where it exits the apparatus.

11 . Only use attachments/accessories

specified by the manufacturer.

12. Use only with the

cart, stand, tripod,

bracket, or table

specified by the

manufacturer, or sold

with the apparatus.

When a cart is used,

use caution when

moving the cart/apparatus combination to

avoid injury from tip-over.

13. Unplug this apparatus during lightning storms

or when unused for long periods of time.

14. Refer all servicing to qualified service

personnel. Servicing is required when the

apparatus has been damaged in any way,

such as when the power-supply cord or

plug is damaged, liquid has been spilled

or objects have fallen into the apparatus,

the apparatus has been exposed to rain

or moisture, does not operate normally, or

has been dropped.

Contents

SAFETY INFORMATION

Warning ..................................................... 2

Precautions ............................................... 3

GETTING STARTED

Before using the User Manual .................... 4

Logos of Discs the player can play ............ 5

Accessories ............................................... 6

Front Panel ................................................ 7

Rear Panel ................................................. 7

Remote Control ......................................... 7

CONNECTIONS

Connecting to a TV .................................... 8

Connecting to an Audio System ................ 8

Connecting to a Network Router ............... 9

SETTINGS

The Setup Procedure ............................... 10

Menu Navigation ...................................... 10

Accessing the Settings Menu .................. 10

Picture Settings ....................................... 10

Sound Settings ........................................ 11

Network Settings ..................................... 12

System Settings ...................................... 16

Language Settings ................................... 16

Security Settings...................................... 16

General Settings ...................................... 17

Support Settings ..................................... 17

MEDIA PLAY

Playing a Commercially Recorded Disc .... 18

Playing Files on a USB Device ................. 18

Playing a Disc with User Recorded

Content ................................................... 18

Using DLNA ............................................. 19

Controlling Video Playback ...................... 19

Controlling Music Playback ...................... 20

Playing Photo Contents ........................... 21

APPENDIX

Troubleshooting ....................................... 22

Specifications .......................................... 23

Getting Started

Before using the User Manual

Disc Types and Contents your player can play

Media Disc Type Details

VIDEO

Blu-ray Disc BD-ROM or BD-RE/-R recorded in the BD-RE format.

DVD-VIDEO

DVD-RW

DVD-R

DVD+RW

DVD+R

DVD-VIDEO, recorded DVD+RW/DVD-RW(V)/DVD-R/+R that have

been recorded and finalized, or a USB storage media containing

MKV or MP4 contents.

MUSIC

CD-RW/-R,

DVD-RW/-R,

BD-RE/-R

Music recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R or a USB

storage media containing MP3 or WMA contents.

PHOTO

CD-RW/-R,

DVD-RW/-R,

BD-RE/-R

Photos recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R or a USB

storage media containing JPEG contents.

✎

NOTES

The player may not play certain CD-RW/-R and DVD-R because of the disc type or recording conditions.

If a DVD-RW/-R has not been recorded properly in DVD video format, it will not be playable.

Your player will not play content that has been recorded on a DVD-R at a bit-rate that exceeds 10 Mbps.

Your player will not play content that has been recorded on a BD-R or USB device at a bitrate that exceeds 25 Mbps.

Playback may not work for some types of discs, or when you use specific functions, such as angle change

and aspect ratio adjustment. Information about the discs is written in detail on the disc box. Please refer to

this if necessary.

When you play a BD-J title, loading may take longer than a normal title or some functions may perform slowly.

Disc types your player cannot play

• HD DVD

• DVD-ROM/PD/

MV, etc

• DVD-RAM

• Super Audio CD

(except CD layer)

•

DVD-RW (VR mode)

•

CVD/CD-ROM/CDV/

CD-G/CD-I/LD

(CD-Gs play audio

only, not graphics.)

• 3.9 GB DVD-R for

Authoring.

Region Code

Both players and discs are coded by region.

These regional codes must match for a disc

to play. If the codes do not match, the disc

will not play.

The Region Code for this player is displayed

on the rear panel of the player.

Disc

Type

Region

Code

Area

Blu-ray

Disc

North America, Central

America, South America,

Korea, Japan, Taiwan, Hong

Kong and South East Asia.

Europe, Greenland, French

territories, Middle East, Africa,

Australia and New Zealand.

India, China, Russia, Central

and South Asia.

DVD-

VIDEO

The U.S., U.S. territories and

Canada

Europe, Japan, the Middle

East, Egypt, South Africa,

Greenland

Taiwan, Korea, the

Philippines, Indonesia, Hong

Kong

Mexico, South America,

Central America, Australia,

New Zealand, Pacific

Islands, Caribbean

Russia, Eastern Europe,

India, most of Africa, North

Korea, Mongolia

China

Logos of Discs the player

can play

Blu-ray Disc BD-LIVE

DivX

NTSC broadcast system in

U.S.A, Canada, Korea, Japan

Supported File Formats

Notes on the USB connection

•

Your player supports USB storage media,

MP3 players, digital cameras, and USB card

readers.

•

The player does not support folder or file

names longer than 128 characters.

•

Some USB/External HDD/digital camera

devices may not be compatible with the player.

•

Your player supports the FAT16, FAT32, and

NTFS file systems.

•

Connect USB devices directly to the player’s

USB port. Connecting through a USB cable

may cause compatibility problems.

•

Inserting more than one memory device into

a multi-card reader may cause the reader to

operate improperly.

•

The player does not support the PTP protocol.

• Do not disconnect a USB device during a

"loading" process.

• The bigger the image resolution, the

longer the image takes to display.

•

This player cannot play MP3 files with DRM (Digital Rights Management) downloaded from

commercial sites.

•

Your player only supports video with a frame rate under 30fps (frames per second).

•

Your player only supports USB Mass Storage Class (MSC) devices such as thumb drives and

USB HDD. (HUB is not supported.)

•

Certain USB HDD Devices, multi-card readers and thumb drives may not be compatible with this player.

•

If some USB devices require excessive power, they may be limited by the circuit safety device.

•

If playback from a USB HDD is unstable, provide additional power by plugging the HDD into a

wall socket.

If the problem continues, contact the USB HDD manufacturer.

•

SAMSUNG is not responsible for any data file damage or data loss.

•

Your player does not support NTFS compressed files, sparse files, or encrypted files.

•

You can repair or format a USB device on your Desktop PC. (MS-Windows OS only).

Video File Support

File Extension Container Video Codec Audio Codec Resolution

*.avi

AVI

DivX 3.11/4/5/6

MP3

Dolby Digital

DTS

WMA

PCM

1920x1080

MP4v3

H.264 BP/MP/HP

1920x1080

*.mkv

MKV

VC-1 AP

MP3

Dolby Digital

DTS

1920x1080

H.264 BP/MP/HP

1920x1080

*.wmv

WMV (wmv9)

VC-1 AP

WMA

1920x1080

VC-1 SM

1920x1080

*.mp4

MP4

MP4 (mp4v)

AAC

1920x1080

H.264 BP/MP/HP

1920x1080

*.mpg

*.mpeg

MPEG

MPEG1

MP1, 2

Dolby Digital

DTS

1920x1080

MPEG2

1920x1080

H.264 BP/MP/HP

1920x1080

• Limitations

- Even when a file is encoded by a supported codec listed above, the file might not be

played if its content has a problem.

- Normal playback is not guaranteed if the file’s container information is wrong or the file

itself is corrupted.

- Files having a higher Bit rate/frame rate than standard may stutter during sound/video playback.

- The Seek (skip) function is not available if the file’s index table is damaged.

• Video decoder

- Supports up to H.264 Level 4.1 and AVCHD

- Does not support H.264 FMO/ASO/RS and VC1 SP/MP/AP L4

- MPEG4 SP, ASP :

Below 1280 x 720 : 60 frames max

Above 1280 x 720 : 30 frames max

- Does not support GMC 2 or higher

• Audio decoder

- Supports WMA 7, 8, 9 and STD

- Does not support WMA sampling rate of 22050Hz mono.

- AAC: Max sampling rate: 96Khz (8, 11, 12, 16, 22,24, 32,44.1, 48, 64, 88.2, 96)

Max bitrate: 320kbps.

Supported DivX subtitle file formats

*.ttxt, *.smi, *.srt, *.sub, *.txt

✎

NOTES

Playback of some DivX, MKV or MP4 file may not be supported depending on their video resolution and

frame rate.

Music File Support

File Extension Container Audio Codec Support Range

*.mp3

MP3 MP3

*.wma

WMA WMA

* Sampling rates (in kHz) - 8, 11, 16, 22, 32, 44.1, 48

* Bit rates - All bit-rates from 5kbps to 355kbps

Picture File Support

File Extension Type Resolution

*.jpg

*.jpeg

*.jpe

JPEG

15360x8640

*.png

PNG

15360x8640

AVCHD (Advanced Video Codec High Definition)

•

This player can play back AVCHD format discs. These discs are normally recorded and used in

camcorders.

•

The AVCHD format is a high definition digital video camera format.

•

The MPEG-4 AVC/H.264 format compresses images with greater efficiency than the

conventional image compressing format.

•

Some AVCHD discs use the "x.v.Color" format. This player can play back AVCHD discs that

use "x.v.Color" format.

•

"x.v.Color" is a trademark of Sony Corporation.

•

"AVCHD" and the AVCHD logo are trademarks of Matsushita Electronic Industrial Co., Ltd. and

Sony Corporation.

✎

NOTES

Some AVCHD format discs may not play, depending on the recording condition.

AVCHD format discs need to be finalized.

"x.v.Color" offers a wider color range than normal DVD camcorder discs.

Accessories

Check for the supplied accessories shown below.

SCREEN

VIEW A-B

FULLBONUS REPEAT REPEAT

HDMI cable

Batteries for Remote

Control (AAA Size)

User Manual Remote Control

Front Panel

DISC TRAY

POWER BUTTON

OPEN/CLOSE BUTTON

USB HOST

REMOTE CONTROL SENSOR

✎

NOTES

You can perform software upgrades using the USB Host jack with a USB flash memory stick only.

Please open and pull out the USB cover before inserting USB drive.

Rear Panel

HDMI OUT LAN DIGITAL AUDIO OUT

Remote Control

Tour of the Remote Control

SCREEN

VIEW A-B

FULLBONUS REPEAT REPEAT

Turn the player on and off.

Allows you to repeat A-B disc.

Press the number buttons to operate options.

Press to open and close the disc tray.

Use to enter the disc menu.

Press to skip backwards or forwards.

Press to stop a disc.

Press to use bonusview function.

Return to the previous menu.

These buttons are used both for menus on the

player and also several Blu-ray Disc functions.

Use to select menu items and change menu

values.

Press to use the Tools menu.

Use to access various audio functions on a

disc (Blu-ray Disc/DVD).

Press to play a disc.

Press to pause a disc.

Turn the TV on and off.

Press to switch the Blu-ray Disc/DVD’s

subtitle language.

Use to enter the popup menu/title menu.

Press to search a disc backwards or

forwards.

Press to move to the Home menu.

Press to see the full screen on a TV.

During the Blu-ray Disc/DVDs playback, Full

Screen button does not operate.

Press to exit the menu.

Use to display the playback information

when playing a Blu-ray Disc/DVDs.

Allows you to repeat a title, chapter, track or

disc.

TV volume adjustment.

After setup, allows you to set the input

source on your TV.

Installing batteries

✎

NOTES

If the remote does not operate properly:

•

Check the polarity (+/–) of the batteries.

•

Check if the batteries are drained.

•

Check if the remote sensor is blocked by obstacles.

•

Check if there is any fluorescent lighting nearby.

CAUTION

Dispose of batteries according to local environmental

regulations. Do not put them in the household trash.

Do not dispose of batteries in a fire.

Do not short circuit, disassemble or overheat the batteries.

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

Connections

Connecting to a TV

Connect an HDMI cable from the HDMI OUT jack on the back of the product to the

HDMI IN jack on your TV.

- Do not connect the power cord to the wall outlet until you have made all the other

connections.

- When you change the connections, turn off all devices before you start.

Audio

Video

✎

NOTES

If you use an HDMI-to-DVI cable to connect to your display device, you must also connect the Digital Audio

Out on the player to an audio system to hear audio.

An HDMI cable outputs digital video and audio, so you don't need to connect an audio cable.

Depending on your TV, certain HDMI output resolutions may not work. Please refer to the user manual of your

TV.

When you connect the player to your TV using the HDMI cable or to a new TV, and then turn it on for the first

time, the player automatically sets the HDMI output resolution to the highest supported by the TV.

A long HDMI cable may cause screen noise. If this occurs, set HDMI Deep Color to Off in the menu.

To view video in the HDMI 720p, 1080i, or 1080p output mode, you must use a High speed HDMI cable.

HDMI outputs only a pure digital signal to the TV.

If your TV does not support HDCP (High-bandwidth Digital Content Protection), random noise appears on the

screen.

Connecting to an Audio System

You can connect the Blu-ray player to an audio system using one of the methods

illustrated below.

- Do not connect the power cord to the wall outlet until you have made all the other

connections.

- When you change the connections, turn off all devices before you start.

Method 1 Connecting to an HDMI compatible AV receiver

•

Connect an HDMI cable from the HDMI OUT jack on the back of the product to

the HDMI IN jack on your receiver.

•

Best quality (Recommended)

Method 2 Connecting to an AV receiver with a Digital Coaxial Cable

•

Using a digital Coaxial cable (not supplied), connect the Coaxial Digital Audio Out

jack on the product to the Digital Coaxial In jack of the receiver.

•

Good quality

•

You will hear sound only through the front two speakers with Digital Output set to PCM.

AudioAudio

Method 2Method 1

Connecting to a Network Router

You can connect your player to your network router using one of the methods

illustrated below.

To use the DLNA network functionality, you must connect your PC to your network

as shown in the illustration.

The connection can be wired or wireless.

Wired Network

Broadband

service

Broadband

service

Broadband modem

(with integrated router)

Broadband

modem

Router

✎

NOTES

Internet access to Samsung's software update server may not be allowed, depending on the router you use

or your ISP's policy. For more information, contact your ISP (Internet Service Provider).

DSL users, please use a router to make a network connection.

Wireless Network

Wireless Router

Broadband service

✎

NOTES

If your wireless router supports DHCP, this player can use a DHCP or static IP address to connect to the

wireless network.

Set your wireless router to Infrastructure mode. Ad-hoc mode is not supported.

The player supports only the following wireless security key protocols:

- WEP (OPEN/SHARED), WPA-PSK (TKIP/AES),

WPA2-PSK (TKIP/AES)

Select a channel on the wireless router that is not currently being used. If the channel set for the wireless

router is currently being used by another device nearby, it will result in interference and communication

failure.

If you select the Pure High-throughput (Greenfield) 802.11n mode and set the Encryption type on your router

to WEP, TKIP or TKIP-AES (WPS2Mixed), the player will not support a connection in compliance with new Wi-

Fi certification specifications.

Wireless LAN, by its nature, may cause interference, depending on the operating conditions (router

performance, distance, obstacles, interference by other radio devices, etc).

Settings

The Setup Procedure

•

The Home screen will not appear if you

do not configure the setup.

•

The OSD (On Screen Display) may

change in this player after you upgrade

the software version.

•

The access steps may differ depending

on the menu you selected.

•

After the setup process is completed, the

panel buttons and remote control can be

operated.

After you have connected the player

to your TV, turn on the TV and player.

When you turn on the player the first

time, the player's Setup screen appears

on the TV. The Setup procedure lets you

set the On Screen Display (OSD) and

menu languages, the aspect ratio (screen

size), the network type, and connect the

player to your network.

✎

NOTES

The Home menu will not appear if you do not

configure the Setup except as noted below.

If you press the BLUE (D) button during network

setup, you can access the Home menu even if

the network setup is not completed yet.

When you return to the Home menu, the full

screen mode is cancelled automatically.

If you want to display the Setup screen again

to make changes, press the

button on

the front panel of the player for more than 5

seconds with no disc inserted. This resets the

player to its default settings.

After the setup process is complete, you can

operate the HDMI-CEC function.

If you want to use the Anynet+(HDMI-CEC)

function to aid in the initial set up process,

please follow the instructions below.

1) Connect the player to an Anynet+(HDMI-CEC)

compliant Samsung TV using HDMI Cable.

2) Set the Anynet+(HDMI-CEC) feature to On in

both the TV and the player.

3) Set the TV to the Setup Procedure.

If you leave the player in the stop mode for

more than 5 minutes without using it, a screen

saver will appear on your TV. If the player is

left in the screen saver mode for more than 25

minutes, the power will automatically turn off.

Menu Navigation

SCREEN

VIEW A-B

FULLBONUS REPEAT REPEAT

HOME Button : Press to move to the Home

menu.

RETURN Button : Return to the previous

menu.

(Enter) / DIRECTION Button :

Move the cursor or select an item.

Activate the currently selected item.

Confirm a setting.

EXIT Button : Press to exit the current menu.

• Home Menu

App 1 App 2 App 3 App 4 App 5

App 6

Change Device

Settings

PLAY DISC PHOTOS VIDEOS MUSIC

No Disc

Selects VIDEOS.

Selects MUSIC.

Selects Settings.

Selects Change Device.

Selects PHOTOS.

Selects PLAY DISC.

Selects applications.

✎

NOTES

The Videos, Photos, and Music options require

that you have an appropriate disc inserted into the

player or a USB flash device attached to the player.

Accessing the Settings Menu

To access the Settings menu and sub-

menus, follow these steps:

Press the POWER button.

The Home Menu appears.

Press the ▲▼◄► buttons to select

Settings, and then press the

button.

Press the ▲▼ buttons to select the

desired submenu, and then press

the

button.

Press the ▲▼ buttons to select the

desired item, and then press the

button.

Press the EXIT button to exit the

menu.

✎

NOTES

The access steps may differ depending on

the menu you selected. The OSD (On Screen

Display) may change in this player after you

upgrade the software version.

Picture Settings

You can configure various display

options such as the TV Aspect Ratio,

Resolution, etc.

TV Aspect Ratio

Depending on the type of television you

have, you may want to adjust the screen

size setting.

✎

NOTES

Depending on the disc type, some aspect

ratios may not be available.

If you select an aspect ratio and option which

is different than the aspect ratio of your

TV screen, the picture might appear to be

distorted.

BD Wise (Samsung TVs only)

BD Wise is Samsung’s latest inter-

connectivity feature.

When you connect a Samsung player

and a Samsung TV with BD Wise to

each other via HDMI, and BD Wise is

on in both the player and TV, the player

outputs video at the video resolution and

frame rate of the Blu-ray Disc/DVDs.

✎

NOTES

When BD Wise is on, the Resolution setting

automatically defaults to BD Wise and BD Wise

appears in the Resolution menu.

If the player is connected to a device that does

not support BD Wise, you cannot use the BD

Wise function.

For proper operation of BD Wise, set the BD

Wise menu of both the player and the TV to

Resolution

Lets you set the output resolution of

the HDMI video signal to Auto, 1080p,

1080i, 720p or 480p. The number

indicates the number of lines of video

per frame. The i and p indicate interlaced

and progressive scan, respectively. The

more lines, the higher the quality.

Resolution according to the output

mode

• Blu-ray Disc/E-contents/Digital

Contents playback

Output

Setup

HDMI / connected

HDMI Mode

Blu-ray

Disc

E-contents/

Digital

contents

BD Wise

Resolution of

Blu-ray Disc

1080p

Auto

Max. Resolution

of TV input

Max. Resolution

of TV input

1080p@60F

(Movie Frame : Off)

1080p@60F 1080p@60F

Movie Frame :

Auto (24Fs)

1080p@24F 1080p@24F

1080i 1080i 1080i

720p 720p 720p

480p 480p 480p

• DVD playback

Output

Setup

HDMI / connected

HDMI Mode

BD Wise 480i

Auto Max. Resolution of TV input

1080p 1080p

1080i 1080i

720p 720p

480p 480p

✎

NOTES

If the TV you connected to the player does

not support Movie Frame or the resolution

you selected, the message "If no pictures are

shown after selecting ‘Yes’, please wait for 15

seconds to return to the previous resolution."

appears. If you select Yes, the TV’s screen

will go blank for 15 seconds, and then the

resolution will revert to the previous resolution

automatically.

If the screen stays blank after you have

changed the resolution, remove all discs,

and then press and hold the

button on the

front of the player for more than 5 seconds.

All settings are restored to the factory default.

Follow the steps on the previous page to

access each mode and select the Display

Setup that your TV will support.

When the factory default settings are restored,

all stored user BD data is deleted.

The Blu-ray Disc must have the 24 frame

feature for the player to use the Movie Frame

(24Fs) mode.

Movie Frame (24Fs)

Setting the Movie Frame (24Fs) feature

to Auto allows you to adjust the player’s

HDMI output to 24 frames per second

for improved picture quality.

You can enjoy the Movie Frame (24Fs)

feature only on a TV supporting this

frame rate. You can select Movie Frame

only when the player is in the HDMI

1080p output resolution modes

HDMI Color Format

Lets you set the color space format for

HDMI output to match the capabilities of

the connected device (TV, monitor, etc).

HDMI Deep Color

Lets you output video from the HDMI

OUT jack with Deep Color. Deep

Color provides more accurate color

reproduction with greater color depth.

Progressive Mode

Lets you improve picture quality when

viewing DVDs.

Sound Settings

Digital Output

Lets you select the digital audio output

format that is suitable for your TV or AV

Receiver. For more details, please refer

to the Digital Output Selection table.

✎

NOTES

Be sure to select the correct Digital Output or

you will hear no sound or just loud noise.

If the HDMI device (AV receiver, TV) is not

compatible with compressed formats (Dolby

Digital, DTS), the audio signal outputs as PCM.

Regular DVDs do not have BONUSVIEW audio

and Navigation Sound Effects.

Some Blu-ray Discs do not have BONUSVIEW

audio and Navigation Sound Effects.

If you play MPEG audio soundtracks, the audio

signal outputs as PCM regardless of your

Digital Output selections (PCM or Bitstream).

If your TV is not compatible with compressed

multi-channel formats (Dolby Digital, DTS), the

player may output PCM 2ch downmixed audio

even though you selected Bitstream (either Re-

encoded or Unprocessed) in the setup menu.

If your TV is not compatible with PCM sampling

rates over 48kHz, the player may output 48kHz

downsampled PCM audio even though you set

PCM Downsampling to Off.

PCM Downsampling

Lets you choose to have 96KHz PCM

signals downsampled to 48KHz before

they are outputted to an amplifier.

Choose On if your amplifier or receiver is

not compatible with a 96KHz signal

Dynamic Range Control

Lets you apply dynamic range control

to Dolby Digital, Dolby Digital Plus, and

Dolby TrueHD audio.

•

Auto : Automatically controls the

dynamic range of Dolby TrueHD

audio, based on information in the

Dolby TrueHD soundtrack.

Also turns dynamic range control on

for Dolby Digital and Dolby Digital Plus.

•

Off : Leaves the dynamic range

uncompressed, letting you hear the

original sound.

•

On : Turns dynamic range control on

for all three Dolby formats. Quieter

sounds are made louder and the

volume of loud sounds is reduced.

Downmixing Mode

Lets you select the multi-channel

downmix method that is compatible with

your stereo system. You can choose

to have the player downmix to normal

stereo or to surround compatible stereo.

Network Settings

To begin setting up the network

connection for your player, follow these

steps:

In the Home menu, press the ▲▼

◄► buttons to select Settings, and

then press the

button.

Press the ▲▼ buttons to select

Network, and then press the

button.

Press the ▲▼ buttons to select

Network Settings, and then press

the

button.

Press the ▲▼ buttons to select

Network Type, and then press the

button.

Press the ▲▼ buttons to select

Wired or Wireless, and then press

the

button.

Go to the next section.

Digital Output Selection

Setup PCM

Bitstream

(Unprocessed)

Bitstream

(Re-encoded DTS)

Bitstream

(Re-encoded Dolby D)

Connection

HDMI

Receiver

Coaxial

HDMI

Receiver

Coaxial

HDMI Receiver or

Coaxial

HDMI supported AV

receiver or Coaxial

Audio

Stream on

Blu-ray

Disc

PCM

Up to

7.1ch

PCM 2ch PCM PCM 2ch Re-encoded DTS Re-encoded Dolby Digital *

Dolby Digital PCM 2ch PCM 2ch Dolby Digital

Dolby

Digital

Re-encoded DTS Re-encoded Dolby Digital *

Dolby Digital

Plus

PCM 2ch PCM 2ch

Dolby Digital

Plus

Dolby

Digital

Re-encoded DTS Re-encoded Dolby Digital *

Dolby TrueHD PCM 2ch PCM 2ch

Dolby

TrueHD

Dolby

Digital

Re-encoded DTS Re-encoded Dolby Digital *

DTS PCM 2ch PCM 2ch DTS DTS Re-encoded DTS Re-encoded Dolby Digital *

DTS-HD High

Resolution

Audio

PCM 2ch PCM 2ch

DTS-HD High

Resolution

Audio

DTS Re-encoded DTS Re-encoded Dolby Digital *

DTS-HD

Master Audio

PCM 2ch PCM 2ch

DTS-HD

Master Audio

DTS Re-encoded DTS Re-encoded Dolby Digital *

Audio

Stream on

DVD

PCM PCM 2ch PCM 2ch PCM 2ch PCM 2ch PCM 2ch PCM 2ch

Dolby Digital PCM 2ch PCM 2ch Dolby Digital

Dolby

Digital

Dolby Digital Dolby Digital

DTS PCM 2ch PCM 2ch DTS DTS DTS DTS

Definition

for Blu-ray

Disc

Any

Decodes main feature

audio and BONUSVIEW

audio stream together

into PCM audio and

add Navigation Sound

Effects.

Outputs only main feature

audio stream so that your

AV receiver can decode

the audio bitstream.

You will not hear

BONUSVIEW audio and

Navigation Sound Effects.

Decodes main feature

audio and BONUSVIEW

audio stream together

into PCM audio and

add Navigation Sound

Effects, then re-

encodes the PCM audio

into DTS bitstream

Decodes main feature

audio and BONUSVIEW

audio stream together

into PCM audio and add

Navigation Sound Effects,

then re-encodes the PCM

audio into Dolby Digital

bitstream

* If Source Stream is 2ch, "Re-encoded Dolby D" Settings are not applied.

Blu-ray Discs may include three audio streams :

- Main Feature Audio : The audio soundtrack of the main feature.

- BONUSVIEW audio : An additional soundtrack such as the director or actor’s commentary.

- Navigation Sound Effects : When you choose a menu navigation selection, a Navigation

Sound Effect may sound. Navigation Sound Effects are different on each Blu-ray Disc.

Configuring Your Network

Connection

Before you begin, contact your ISP to find

out if your IP address is static or dynamic.

If it is dynamic, and you have a wired or

wireless network, we recommend using

the Automatic configuration procedures

described below.

If you are connecting to a wired network,

connect the player to your router

using a LAN cable before you start the

configuration procedure.

If you are connecting to a wireless

network, disconnect any wired network

connection before you begin.

To begin configuring your network

connection, follow these steps

Wired Network

Wired - Automatic

In the Home screen, select Settings,

and then press the

button.

Select Network, and then press the

button.

Select Network Settings, and then

press the

button.

Select Wired in the Network

Settings screen, and then press the

button.

Select Connect button, and then

press the

button. The product

detects the wired connection,

verifies the network connection and

then connects to the network.

Wired - Manual

If you have a static IP address or the

Automatic procedure does not work,

you'll need to set the Network Settings

values manually.

Follow Steps 1 and 2 in Wired -

Automatic, and then follow these steps:

Select Network Status. The player

searches for a network, and then

displays the connection failed

message.

On the bottom of the screen, select

IP Settings, and then press the

button.

The IP Settings screen appears.

Select the IP Setting field, and then

press the

button.

Select Enter manually in the IP

Setting field, and then press the

button.

Select a value to enter (IP Address,

for example), and then press the

button.

Use the number keypad on your

remote control to enter the numbers for

the value. Use the ◄► buttons on the

remote control to move from entry field

to entry field within a value. When done

with one value, press the

button.

Press the ▲ or ▼ button to move

to another value, and then enter the

numbers for that value following the

instructions in Step 5.

Repeat Steps 5 and 6 until you have

filled in all values.

✎

NOTES

You can get the Network values from your

Internet provider.

When finished entering all the

values, and then press the RETURN

or EXIT buttons. The player verifies

the network connection and then

connects to the network.

Wireless Network

You can setup a wireless network

connection in four ways:

- Wireless Automatic

- Wireless Manual

- WPS(PBC)

- WPS(PIN)

When you configure the wireless network

connection, any wireless network devices

currently connected through the player

or, if applicable, the player's current wired

connection, will be disconnected.

Wireless - Automatic

In the Home screen, select Settings,

and then press the

button.

Select Network, and then press the

button.

Select Network Settings, and then

press the

button.

Select Wireless in the Network

Settings screen, and then press the

button. The player searches

for and then displays a list of the

available networks.

Move

Select

Return

Network Settings

Select your network type.

Network type Wireless

Wireless network

Add Network

You can connect your Blu-ray

player to the internet. Please

select which wireless network

to use.

WPS(PBC) Search

Select the desired network, and then

press the

button.

On the Security screen, enter your

network's Security Code or Pass

Phrase.

Enter numbers directly using the

number buttons on your remote

control. Enter letters by selecting a

letter with an arrow button, and then

pressing

button.

When done, select Done and then

press the

button. The player

verifies the network connection and

then connects to the network.

When verification is complete, select

OK, and then press the

button.

✎

NOTES

You should be able to find the Security Code or

Pass Phrase on one of the set up screens you

used to set up your router or modem.

Wireless - Manual

If you have a static IP address or the

Automatic procedure does not work,

you'll need to set the Network Settings

values manually.

Follow the directions in Wireless -

Automatic through Step 5.

The player searches for a network,

and then displays the connection

failed message.

On the bottom of the screen, select

IP Settings, and then press the

button.

The IP Settings screen appears.

Select the IP Setting field, and then

press the

button.

Select Enter manually in the IP

Setting field, and then press the

button.

Select a value to enter (IP Address,

for example), and then press

button. Use the number keypad

on your remote control to enter the

numbers for the value. Use the ◄►

buttons on the remote control to

move from entry field to entry field

within a value. When done with one

value, press the

button.

Press the ▲ or ▼ button to move

to another value, and then enter the

numbers for that value following the

instructions in Step 6.

Repeat Steps 6 and 7 until you have

filled in all values.

✎

NOTES

You can get the Network values from your

Internet provider.

When finished, and then press

the RETURN or EXIT button. The

Security Screen appears.

✎

NOTES

Contact the manufacturer of the router for

instructions explaining how to access the

route's Set Up screens or refer to the router's

user's manual.

For WPS connection, set your wireless router’s

security encryption to AES. Setting to WEP

security encryption does not support WPS

connection.

Network Test

Use this menu item to check whether your

network connection is working or not.

Network Status

Use to check whether a connection to

a network and the Internet has been

established.

Wi-Fi Direct

The Wi-Fi Direct function allows you

to connect Wi-Fi Direct devices to the

player and each other using a peer-to-

peer network, without a wireless router.

✎

NOTES

Some Wi-Fi Direct devices may not support the

DLNA function if connected via Wi-Fi Direct. If

this is the case, it is advisable to change the

network connection method between devices.

Bluetooth transmissions can interfere with the

Wi-Fi Direct signal. Before you use the Wi-

Fi Direct function, we strongly recommend

that you turn off the Bluetooth function of any

active mobile device.

10 .

On the Security screen, enter your

network's Security Code or Pass

Phrase. Enter numbers directly using

the number buttons on your remote

control. Enter letters by selecting a

letter with the ▲▼◄► buttons, and

then pressing the

button.

11 .

When finished, select Done at the

right of the screen, and then press

the

button.

The player verifies the network

connection and then connects to

the network.

12 .

After the player verifies the network,

select OK, and then press the

button.

WPS(PBC)

In the Home screen, select Settings,

and then press the

button.

Select Network, and then press the

button.

Select Network Settings, and then

press the

button.

Select Wireless in the Network

Settings screen, and then press the

button.

Press the ▲▼ button on your

remote, and then press the ◄►

button to select the WPS(PBC).

Press the

button on your

remote. The "Press the PBC button"

message appears.

Press the WPS(PBC) button on

your router within two minutes. Your

player automatically acquires all the

network settings values it needs and

connects to your network.

The Network Status screen appears.

The player connects to the network

after the network connection is

verified.

WPS(PIN)

Before you begin, open the router's

setup menu on your PC and access the

screen with the WPS PIN entry field.

In the Home screen, select Settings,

and then press the

button.

Select Network, and then press the

button.

Select Network Settings, and then

press the

button.

Select Wireless in the Network

Settings screen, and then press the

button.

The player searches for and then

displays a list of the available networks.

Select the desired network, and then

press the ► button.

Select the WPS(PIN), and then

press the

button. The PIN pop-

up appears.

Enter the PIN into the WPS PIN entry

field in the router's Set Up screen

and then save the the screen.

Turn on the Wi-Fi direct device and

activate its Wi-Fi Direct function.

In the Home screen, select Settings,

and then press the

button.

Select Network, and then press the

button.

Select Wi-Fi Direct, and then press

the

button.

The Wi-Fi Direct devices that you

can connect appear.

You have three ways to complete

the Wi-Fi connection:

•

Through the Wi-Fi device.

•

Through the player using PBC.

•

Through the player using a PIN.

Each is covered below.

Through the Wi-Fi Device

On the Wi-Fi device, follow the

procedure on the device for

connecting to another Wi-Fi Direct

device. See the device's user

manual for instructions.

When you have completed the

procedure, you should see a pop-

up on your TV screen saying that

a device that supports Wi-Fi Direct

has requested to connect. Select

OK, and then press the

button

to accept.

The Connecting pop-up appears,

followed by the Connected pop-

up. When it closes, you should see

the device listed on the Wi-Fi Direct

screen as connected.

Through the Player Using PBC

Select the Wi-Fi Direct device you

want to connect to this player, and

then press the

button. The PBC/

PIN pop up appears.

Select PBC, and then press the

button. The PBC pop-up appears.

Press the PBC button on the Wi-Fi

Direct device within 2 minutes.

The Connecting pop-up appears,

followed by the Connected pop-

up. When it closes, you should see

the device listed on the Wi-Fi Direct

screen as connected.

Through the Player Using a PIN

Select the Wi-Fi Direct device you

want to connect to this player, and

then press the

button. The PBC/

PIN pop up appears.

Select PIN, and then press the

button. The PIN pop-up appears.

Note the PIN code in the pop-up,

and then enter it into the appropriate

field in the Wi-Fi Direct device you

want to connect.

The Connecting pop-up appears,

followed by the Connected pop-

up. When it closes, you should see

the device listed on the Wi-Fi Direct

screen as connected.

✎

NOTES

The current wired or wireless network

connection will be disconnected when you use

the Wi-Fi Direct function.

Text files, such as files with a .TXT or .DOC

extension, will not display when you are using

the Wi-Fi Direct function.

Device Name

Device Name function allows you to

change player's name by selecting

from device name list.

BD-Live Internet Connection

Set to allow or prohibit an Internet

connection when you use the BD-LIVE

service.

•

Allow (All) : The Internet connection

is allowed for all BD-LIVE contents.

•

Allow (Valid Only) : The Internet

connection is allowed only for BD-

LIVE contents containing a valid

certificate.

•

Prohibit : No Internet connection is

allowed for any BD-LIVE content.

✎

NOTES

What is a valid certificate?

When the player uses BD-LIVE to send the

disc data and a request to the server to certify

the disc, the server uses the transmitted data

to check if the disc is valid and sends the

certificate back to the player.

The Internet connection may be restricted

while you are using BD-LIVE contents.

Using BD-LIVE™

Once the player is connected to the

network, you can enjoy various movie-

related service contents using a BD-LIVE

compliant disc.

Attach a USB memory stick to the

USB jack on the front of the player,

and then check its remaining memory.

The memory device must have at least

1GB of free space to accommodate

the BD-LIVE services.

Insert a Blu-ray Disc that supports

BD-LIVE.

Select an item from various BD-LIVE

service contents provided by the

disc manufacturer.

✎

NOTES

The way you use BD-LIVE and the provided

contents may differ, depending on the disc

manufacturer.

The DLNA Function

DLNA lets you play music, video, and

photo files located in your PC on the

player.

To use DLNA with your player, you must

connect the player to your network. (See

page 12-16).

To use DLNA with your PC, you must

install DLNA software on your PC.

System Settings

Setup

By using the Setup function, you can set

the language, Network Settings, etc.

For more information about the Setup

function, refer to the Setup of this user

manual (See page 10).

Quick Start

You can turn on the power quickly by

decreasing the boot time.

✎

NOTES

If this function is set to On, Standby power

consumption will be increased.

Anynet+ (HDMI-CEC)

Anynet+ is a convenient function that

offers linked operations with other

Samsung players that have the Anynet+

feature.

To operate this function, connect this

player to an Anynet+ Samsung TV with

an HDMI cable.

With Anynet+ on, you can operate this

player using a Samsung TV remote

control and start disc playback simply

by pressing the PLAY ( ) button on

the TV’s remote control.

For more information, please see the TV

user manual.

✎

NOTES

This function is not available if the HDMI cable

does not support CEC.

If your Samsung TV has an Anynet+ logo, then

it supports the Anynet+ function.

Depending on your TV, certain HDMI output

resolutions may not work.

Please refer to the user manual of your TV.

After the product was turned off, disconnecting

and connecting the power cable turns it on

automatically. At the moment, it automatically

turns off in about 15 seconds for re-

establishing Anynet+ connection.

For some TV products, if connected to this

product with Anynet+ function, turning the

TV on may display a warning popup message

saying no connection was found. Still, Anynet+

connection is properly established and

available to use

BD Data Management

Enables you to manage the downloaded

contents you accessed through a Blu-

ray disc that supports the BD-LIVE

service and stored on a flash drive.

You can check the device’s information

including the storage size, delete the

BD data, or change the Flash memory

device.

✎

NOTES

In the external memory mode, disc playback

may be stopped if you disconnect the USB

device in the middle of playback.

Your player supports the FAT16, FAT32, and

NTFS file systems. We recommend you use

USB devices that support USB 2.0 protocol

with 4 MB/sec or faster read/write speed.

The Resume Play function may not work after

you format the storage device.

The total memory available to BD Data

Management may differ, depending on the

conditions.

DivX® Video On Demand

View DivX® VOD Registration Codes to

purchase and play DivX® VOD contents.

Language Settings

You can select the language you prefer

for the On-Screen menu, disc menu,

audio, and subtitles.

✎

NOTES

The selected language will only appear if it is

supported on the disc.

Security Settings

The default security PIN is 0000. Enter

the default PIN to access the security

function if you haven't created your own

PIN. After you have accessed the security

function for the first time, change the PIN

using the Change PIN function.

BD Parental Rating

Prevents playback of Blu-ray Discs with

specific age ratings unless the 4 digit

PIN is entered.

DVD Parental Rating

This function works in conjunction with

DVDs that have been assigned an age

rating or numeric rating that indicates

the maturity level of the content. These

numbers help you control the types of

DVDs that your family can watch.

Select the rating level you want to set.

For example, if you select Level 6, discs

rated above 6 - Level 7 and 8 - will not play.

A larger number indicates more mature

content.

Change PIN

Change the 4-digit password used to

access security functions.

If you forget your password

Remove any discs.

Press and hold the

button on the

front panel for 5 seconds or more.

All settings will revert to the factory

settings.

✎

NOTES

When the factory default settings are restored,

all the user stored BD data will be deleted.

General Setting

Time Zone

Lets you specify the time zone that is

applicable to your area.

Support Settings

Software Upgrade

The Software Upgrade menu allows

you to upgrade the player’s software for

performance improvements or additional

services.

By Online

To upgrade By Online, follow these

steps:

In the player’s menu, go to Settings

> Support > Software Upgrade.

Select By Online, and then press

the

button. The Connecting to

Server message appears.

A popup message will appear if an

update is available.

If you select Yes, download process

started. (Never turn the player on

during an upgrade.)

When the update is completed, the

player will restart automatically.

✎

NOTES

The upgrade is complete when the player

turns off, and then turns on again by itself.

Never turn the player off or back on manually

during the update process.

Samsung Electronics takes no legal

responsibility for player malfunction caused by

an unstable Internet connection or consumer

negligence during a software upgrade.

No disc should be in the product when you

upgrade the software By Online.

By USB

To upgrade by USB, follow these steps:

Visit www.samsung.com/

bluraysupport.

Download the latest USB software

upgrade zip archive to your computer.

Unzip the zip archive to your

computer. You should have a single

RUF file with the same name as the

zip file.

Copy the RUF file to a USB flash

drive.

Make sure there is no disc in the

player, and then insert the USB flash

drive into the USB port of the player.

In the player’s menu, go to Settings

> Support > Software Upgrade.

Select By USB

✎

NOTES

No disc should be in the product when you

upgrade the software using the USB Host jack.

When the software upgrade is done, check

the software details in the software Upgrade

menu.

Do not turn off the player during the

software upgrade. It may cause the player to

malfunction.

Software upgrades using the USB Host jack

must be performed with a USB flash memory

stick only.

Auto Upgrade Notification

If you have connected the player to your

network, and then set Auto Upgrade

Notification on, the player automatically

notifies you when a new software

version is available for the player.

To set Auto Upgrade Notification on,

follow these steps:

Select Auto Upgrade Notification,

and then press the

button.

Use the ▲▼ buttons to select On,

and then press the

button.

If there is a new software version

available, the player notifies you with a

popup message.

To upgrade the firmware, select Yes

in the Pop-up. The player turns off

automatically, then restarts, and

begins the download. (Never turn

the player on or off manually during

an upgrade.)

The update progress popup

appears.

When the update is completed, the

player will restart automatically.

✎

NOTES

The upgrade is complete when the player

turns off, and then turns on again by itself.

Never turn the player off or on manually during

the update process.

Samsung Electronics takes no legal

responsibility for player malfunction caused by

an unstable Internet connection or consumer

negligence during software upgrade.

Contact Samsung

Provides contact information for

assistance with your player.

Lets you view the general disclaimer

regarding third party contents and

services.

Reset

Returns all settings to their factory

defaults except for the network settings.

Media Play

Playing a Commercially

Recorded Disc

Press the

button to open the

disc tray.

Place a disc gently into the disc

tray with the disc's label facing up.

Press the

button to close

the disc tray. Playback starts

automatically.

Playing Files on a USB

Device

There are two methods you can use to

play or view multimedia files located on

a USB device through your player.

Method 1

Turn the player on.

Connect the USB device to the USB

port on the front panel of the player.

The New Device Connected pop-up

appears.

App 1 App 2 App 3 App 4 App 5

App 6

Change Device

Settings

PLAY DISC PHOTOS VIDEOS MUSIC

No Disc

New device connected.

Photos

Videos

Music

123

Move

Enter

Return

✎

NOTES

If the pop-up does not appear, go to Method 2.

Use the ▲▼ buttons to select

Photos, Videos or Music, and then

press the

button. The Photos,

Videos & Music screen appears

listing the content of the device.

Depending on how the contents is

arranged, you will see either folders,

individual files, or both.

✎

NOTES

Even though the player will display folders for

all content types, it will only display files of

the Content Type you selected in Step 3. For

example, if you selected music, you will only

be able to see music files. You can change this

selection by returning to the Photos, Videos &

Music screen and going to Step 3 in Method 2

below.

If necessary, use the ▲▼◄►

buttons to select a folder, and then

press the

button.

Select a file to view or play, and then

press the

button.

Press the RETURN button to exit a

folder or the EXIT button to return to

the Home screen.

Go to pages 19~21 for instructions

that explain how to control playback

of videos, music, and pictures on a

USB device.

Method 2

Turn the player on.

Connect the USB device to the USB

port on the front panel of the player.

Select Change Device and then

press the ▲▼ to select USB. Press

the

button.

App 1 App 2 App 3 App 4 App 5

App 6

Change Device

Settings

PLAY DISC

PHOTOS VIDEOS MUSIC

No Disc

Change Device

No Disc

123

Use the ▲▼◄► buttons to select

PHOTOS, VIDEOS or MUSIC on

the Home screen, and then press

the

button. The Photos, Videos

& Music screen appears listing the

content of the device. Depending on

how the contents is arranged, you

will see either folders, individual files,

or both.

✎

NOTES

Even though the player will display folders for

all content types, it will only display files of

the Content Type you selected in Step 3. For

example, if you selected music, you will only

be able to see music files. You can change this

selection by returning to the Photos, Videos &

Music screen and repeating Step 3.

If necessary, use the ▲▼◄►

buttons to select a folder, and then

press the

button.

Use the ▲▼◄► buttons to select

a file to view or play, and then press

the

button.

Press the RETURN button to exit a

folder or the EXIT button to return to

Home screen.

Go to pages 19~21 for instructions

that explain how to control playback

of videos, music, and pictures on a

USB device.

✎

NOTES

If you insert a disc when playing a USB

device, the device mode changes to "Disc"

automatically.

Playing a Disc with User

Recorded Content

You can play multimedia files you have

recorded on Blu-ray, DVD, or CD discs.

Place a user recorded disc into the

disc tray with the disc’s label facing

up, and then close the tray.

Use the ◄► buttons to select the

type of content you want to view

or play - VIDEOS, PHOTOS, or

MUSIC - and then press the

button.

✎

NOTES

Even though the player will display folders for

all content types, it will only display files of

the Content Type you selected in Step 2. For

example, if you selected music, you will only

be able to see music files. You can change this

selection by returning to the Home screen and

repeating Step 2.

Press the RETURN button one or

more times to exit a current screen,

exit a folder, or to return to the Home

screen. Press the EXIT button to

return directly to the Home Screen.

Go to pages 19~21 for instructions

that explain how to control playback of

videos, music, and pictures on a disc.

Controlling Video Playback

You can control the playback of video

content located on a Blu-ray disc, DVD,

CD, USB device, or you computer.

Depending on the media, some of the

functions described in this manual may

not be available.

During Blu-ray or DVD disc playback,

the Full screen button does not operate.

Buttons on the Remote Control

used for Video Playback

SCREEN

VIEW A-B

FULLBONUS REPEAT REPEAT

Playback related buttons

The player does not play sound in

Search, Slow or Step mode.

•

To return to normal speed playback,

press the

button.

button

Starts playback.

button

Stops playback.

button

Pauses playback.

Fast Motion

Play

During playback, press the

button.

Each time you press the

button, the playback speed will

change.

Slow Motion

Play

In pause mode, press the

button.

Each time you press the

button,

the playback speed will change.

Step Motion

Play

In pause mode, press the

button.

Each time you press the

button,

a new frame appears.

Skip Motion

Play

During playback, press the

button.

Each time you press the

button, the disc moves to the

previous or next chapter or file.

Using the disc menu, title

menu, popup menu, and title

list

DISC MENU

button

During playback, press this button

to start the disc menu function.

TITLE MENU

button

During playback, press this button

to start the title menu function.

POPUP MENU

button

During playback, press this button

to start the popup menu function.

A screen appears listing the

contents of the disc. Depending on

how the contents are arranged, you

will see either folders, individual files,

or both.

If necessary, use the ▲▼◄►buttons

to select a folder, and then press the

button.

Use the ◄►▲▼ buttons to select

a file to view or play, and then press

the

button.

Press the RETURN button one or

more times to exit a current screen,

exit a folder, or to return to the Home

screen. Press the EXIT button to

return directly to the Home Screen.

Go to pages 19~21 for instructions

that explain how to control playback of

videos, music, and pictures on a disc.

Using DLNA

DLNA Connection

PC Blu-ray Disc Player

Play back PC's

files

Connect the Blu-ray Disc Player,

your PC, and/or your DLNA

compatible device to the same

wireless network.

Follow the directions in the DLNA

software Installation/Instruction

manual to set up devices and files

for playing or viewing.

Select Change Device on the

player's Home screen, and then

press the

button. In the list

of DLNA connected devices that

appears, select your PC or other

DLNA compatible device, and then

press the

button.

Use the ◄► buttons to select the

type of content you want to view

or play - VIDEOS, PHOTOS, or

MUSIC - and then press the

button.

✎

NOTES

Even though the player will display folders for

all content types, it will only display files of

the Content Type you selected in Step 4. For

example, if you selected music, you will only

be able to see music files. You can change this

selection by returning to the Home screen and

repeating Step 4.

A screen appears listing the

contents of the PC or DLNA device.

Depending on how the contents are

arranged, you will see either folders,

individual files, or both.

If necessary, use the ▲▼◄►buttons

to select a folder, and then press the

button.

Use the ◄►▲▼ buttons to select

a file to view or play, and then press

the

button.

Controlling Music Playback

You can control the playback of music

located on a Blu-ray disc, DVD, CD,

USB device, or your computer.

Buttons on the Remote Control

used for Music Playback

SCREEN

VIEW A-B

FULLBONUS REPEAT REPEAT

NUMBER buttons (Audio CD (CD-DA)

only) :

During Playlist playback, press the

desired track number.

The selected track is played.

Skip : During playback, press the

button to move to the previous or

next file of the playlist.

button : Stops a track.

Fast Play (Audio CD (CD-DA) only)

During playback, press the

button.

Each time you press the

button, the playback speed will change.

Pause : Pauses a track.

button : Plays the currently selected

track.

Playlist

To move to the Music List, press the

or RETURN button.

The Music List screen appears.

Select Tools

( )

Jump Page

Return

1/2 Page

MUSIC

TRACK 001