Installation Guide
Home Network System
Indoor Siren
Model No. KX-HNS105
Thank you for purchasing a Panasonic product.
This document explains how to install the indoor siren properly.
For details about how to use the system, refer to the User’s Guide
(page 12).
Please read this document before using the unit and save it for future
reference. For assistance, please contact us at 1-800-272-7033 or visit
our
Web site: http://shop.panasonic.com/support for customers in the
U.S.A.
Please register your product: http://shop.panasonic.com/support
In order to use this device:
R Download the latest version of the [Home Network] app.
R Update your hub to the latest firmware version
(version 5.00 or later).
For more information, refer to the User’s Guide (page 12).
Printed in China
HNS105_(en_en)_0206_ver.111.pdf 1 2017/02/06 12:06:44
Introduction
Accessory information ...............3
Important Information
About this system ......................4
For your safety ...........................
4
Important safety instructions ......5
For best performance ................5
Other information .......................6
Setup
Part names and functions ..........7
LED indicator .............................7
Setup overview ..........................7
Registering the siren ..................8
Confirming the usage area ........9
Installation ...............................10
Note about power
connections .............................11
Appendix
Testing the siren ......................12
Adjusting the siren’s volume ....12
Features available when using the
[Home Network] app ................12
Accessing the User’s Guide ....12
Specifications ..........................13
FCC and other information ......14
Customer services ...................15
Limited Warranty (ONLY FOR
U.S.A.) .....................................16
2
Table of Contents
HNS105_(en_en)_0206_ver.111.pdf 2 2017/02/06 12:06:44
Accessory information
Supplied accessories
No. Accessory item/Part number Quantity
A AC adaptor/PNLV236-0Y 1
B DC extension cord/PNJA1159Z 1
C Wall mounting screws (25 mm (1 inch))/XTB4+25AVW 2
A B C
Other information
R D
esign and specifications are subject to change without notice.
R The illustrations in these instructions may vary slightly from the actual product.
Trademarks
R i
Phone and iPad are registered trademarks of Apple Inc.
R Android is a trademark of Google Inc.
R Microsoft, Windows, and Internet Explorer are either registered trademarks or
trademarks of Microsoft Corporation in the United States and/or other countries.
R All other trademarks identified herein are the property of their respective owners.
For a
ssistance, please visit http://shop.panasonic.com/support
3
Introduction
HNS105_(en_en)_0206_ver.111.pdf 3 2017/02/06 12:06:44
About this system
R This system is an auxiliary system; it
is not designed to provide complete
protection from property loss.
Panasonic will not be held
responsible in the event that
property loss occurs while this
system is in operation.
R The system’s wireless features are
subject to interference, therefore
functionality in all situations cannot
be guaranteed. Panasonic will not
be held responsible for injury or
damage to property that occurs in
the event of wireless communication
error or failure.
For your safety
T
o prevent severe injury and loss of life/
property, read this section carefully
before using the product to ensure
proper and safe operation of your
product.
WARNING
Power connection
R U
se only the power source marked
on the product.
R Do not overload power outlets and
extension cords. This can result in
the risk of fire or electric shock.
R Completely insert the AC adaptor/
power plug into the power outlet.
Failure to do so may cause electric
shock and/or excessive heat
resulting in a fire.
R Regularly remove any dust, etc.
from the AC adaptor/power plug by
pulling it from the power outlet, then
wiping with a dry cloth. Accumulated
d
ust may cause an insulation defect
from moisture, etc. resulting in a fire.
R Unplug the product from power
outlets if it emits smoke, an
abnormal smell, or makes an
unusual noise. These conditions can
cause fire or electric shock. Confirm
that smoke has stopped emitting
and contact us at
www.panasonic.com/contactinfo
R Unplug from power outlets and
never touch the inside of the product
if its casing has been broken open.
Danger of electric shock exists.
R Never touch the plug with wet
hands. Danger of electric shock
exists.
R Do not connect non-specified
devices.
Installation
R T
o prevent the risk of fire or
electrical shock, do not expose the
product to rain or any type of
moisture.
R Do not place or use this product
near automatically controlled
devices such as automatic doors
and fire alarms. Radio waves
emitted from this product may cause
such devices to malfunction
resulting in an accident.
R Do not allow the AC adaptor to be
excessively pulled, bent or placed
under heavy objects.
R Install the product only on a vertical
surface. Do not install the product on
a ceiling, as the product may fall,
resulting in damage or injury.
R Keep small parts (screws, etc.) out
of the reach of children. There is a
risk of swallowing. In the event they
are swallowed, seek medical advice
immediately.
4
For a
ssistance, please visit http://shop.panasonic.com/support
Important Information
HNS105_(en_en)_0206_ver.111.pdf 4 2017/02/06 12:06:44
Operating safeguards
R Unplug the product from power
outlets before cleaning. Do not use
liquid or aerosol cleaners.
R Do not disassemble the product.
R Never put metal objects inside the
product. If metal objects enter the
product, turn off the circuit breaker
and contact an authorized service
center.
Medical
R C
onsult the manufacturer of any
personal medical devices, such as
pacemakers or hearing aids, to
determine if they are adequately
shielded from external RF (radio
frequency) energy. DECT features
operate between 1.92 GHz and
1.93 GHz with a peak transmission
power of 115 mW.
R Do not use the product in health
care facilities if any regulations
posted in the area instruct you not to
do so. Hospitals or health care
facilities may be using equipment
that could be sensitive to external
RF energy.
CAUTION
Installation and location
R N
ever install wiring during a lightning
storm.
R The AC adaptor is used as the main
disconnect device. Ensure that the
AC outlet is installed near the
product and is easily accessible.
R To avoid the risk of strangulation,
keep the product and the AC
adaptor cord at least 1 m (3 feet)
from a child’s crib and out of the
reach of small children.
Preventing accidents and injuries
R Do not put your ear(s) near the
product, as loud sounds emitted
from the product may cause hearing
impairment.
R Do not look directly at the strobe
light when it is flashing. Light emitted
from the strobe light may cause
damage to the eyes.
R Consider the installation
environment carefully when
installing the product. Pay particular
attention to infants, children, and the
elderly, as they may be more
sensitive to loud sounds and strobe
lights.
Important safety
i
nstructions
When using your product, basic safety
precautions should always be followed
to reduce the risk of fire, electric shock,
and injury to persons, including the
following:
1. Do not use this product near water
for example, near a bathtub,
washbowl, kitchen sink, or laundry
tub, in a wet basement or near a
swimming pool.
2. Use only the power cord indicated
in this document.
SAVE THESE INSTRUCTIONS
For b
est performance
Hub location/avoiding noise
T
he hub and other compatible
Panasonic devices use radio waves to
communicate with each other.
For a
ssistance, please visit http://shop.panasonic.com/support
5
Important Information
HNS105_(en_en)_0206_ver.111.pdf 5 2017/02/06 12:06:44
R F
or maximum coverage and
noise-free communications, place
your hub:
– at a convenient, high, and central
location with no obstructions
between the product and hub in
an indoor environment.
– away from electronic appliances
such as TVs, radios, personal
computers, wireless devices, or
other phones.
– facing away from radio frequency
transmitters, such as external
antennas of mobile phone cell
stations. (Avoid putting the hub
on a bay window or near a
window.)
R If the reception for a hub location is
not satisfactory, move the hub to
another location for better reception.
Environment
R K
eep the product away from
electrical noise generating devices,
such as fluorescent lamps and
motors.
R The product should be kept free
from excessive smoke, dust, high
temperature, and vibration.
R The product should not be exposed
to direct sunlight.
R Do not place heavy objects on top of
the product.
R When you leave the product unused
for a long period of time, unplug the
product from the power outlet.
R The product should be kept away
from heat sources such as heaters,
kitchen stoves, etc. It should not be
placed in rooms where the
temperature is less than 0 °C (32 °F)
or greater than 40 °C (104 °F).
Damp basements should also be
avoided.
R O
perating the product near electrical
appliances may cause interference.
Move away from the electrical
appliances.
Other information
Routine care
R W
ipe the outer surface of the
product with a soft moist cloth.
R Do not use benzine, thinner, or any
abrasive powder.
Notice
6
For a
ssistance, please visit http://shop.panasonic.com/support
Important Information
HNS105_(en_en)_0206_ver.111.pdf 6 2017/02/06 12:06:44
Part names and
functions
A B
D
E
F
C
Horn
Strobe light
F
lashes when the siren is
sounding.
LED indicator
MH
IGHN/MLOWN
Used to adjust the siren’s volume
(page 12).
Rear cover
M N
U
sed to register the siren to the
hub.
LED indicator
You can use the LED indicator to
confirm the siren’s status.
Indicator Status
Green, lit Normal operation
Red,
b
linking
slowly
Siren is not registered
to a hub
Red,
b
linking
Siren is out of range of
the hub
Red,
b
linking
quickly
Alarm system was
triggered
Green,
b
linking
slowly
Registration mode
(You pressed and held
M N)
Off No power
Setup overview
1 I
nitial setup
Make sure you can access the
system using your mobile device.
For details, refer to the System
Setup Guide included with your
hub.
2 Registration
Required only if the siren was
purchased separately (i.e., not as
part of a bundle).
3 Confirm the installation area
Read the information in this
document to confirm that the
desired installation area is suitable
to proper operation.
For a
ssistance, please visit http://shop.panasonic.com/support
7
Setup
HNS105_(en_en)_0206_ver.111.pdf 7 2017/02/06 12:06:44
4 I
nstallation
Install the siren in the desired
location.
Registering the siren
This procedure is not required for
d
evices that were included as part of
a bundle.
Before you can use the siren, it must
b
e registered to the hub.
If you purchased devices separately
(i.e., not as part of a bundle), you must
register each device to the hub.
You can register each device by using
the registration buttons or the [Home
Network] app.
Note:
R Before registering the siren, make
sure the AC adaptors of the hub and
siren are connected and each
device is powered.
Using registration buttons
1 H
ub:
Press and hold M
OTHER
D
EVICEN until the LED indicator
blinks slowly in green.
2 Siren:
Press and hold M
N
until the
LED indicator blinks slowly in
green (page 7).
R When registration is complete,
the hub sounds one long beep.
Note:
R To cancel without registering the
siren, press M
N
on the hub and
on the siren again.
R I
f registration fails, the hub sounds
several short beeps.
Using the app
W
hen you register the siren by using
the [Home Network] app, you can
assign a name to your devices and
group them by location. For more
information, refer to the User’s Guide
(page 12).
8
For a
ssistance, please visit http://shop.panasonic.com/support
Setup
HNS105_(en_en)_0206_ver.111.pdf 8 2017/02/06 12:06:44
Confirming the
usage area
Wireless communication
r
ange
The wireless communication range of
each device in the system from the hub
is approximately 50 m (160 feet)
indoors and approximately 300 m
(1,000 feet) outdoors. Wireless
communication may be unreliable
when the following obstacles are
located between the hub and other
devices.
R Metal doors or screens
R Walls containing aluminum-sheet
insulation
R Walls made of concrete or
corrugated iron
R Double-pane glass windows
R Multiple walls
R When using each device on
separate floors or in different
buildings
Note:
R You can use the siren’s LED
indicator to confirm the siren’s
communication status (page 7). If
the LED indicator is lit in green or is
blinking quickly in red, the siren is
communicating properly with the
hub.
Usage area cautions
U
sing the siren in the following areas
may cause deformation, malfunction, or
operational failure.
R In direct sunlight
R Areas exposed to grease or steam,
such as kitchens
R N
ear fire or heating devices
R Near magnetic fields (such as near
microwaves and magnets)
R Areas subject to extreme
temperature changes, such as next
to air conditioners
R Areas with reflective objects, such
as glass, that can interfere with
detection of temperature variation
R Areas where the temperature is
affected by strong illuminating
objects (such as fluorescent lights)
R Near devices that emit strong radio
waves, such as mobile phones
For a
ssistance, please visit http://shop.panasonic.com/support
9
Setup
HNS105_(en_en)_0206_ver.111.pdf 9 2017/02/06 12:06:44
Installation
Mount the siren on a wall using the
holes in the rear cover.
Note:
R The strobe light flashes when the
siren sounds. Mount the siren in a
location where its strobe light will be
visible.
R Mount the siren on the stable
location where the siren can be
adequately supported when
mounting.
R Mount the siren securely to a wall.
Vibrations may cause it to fall if it is
not secured.
R Do not mount siren on a soft
material. It may fall down, break or
cause injury.
R Do not mount the siren on the
following places: gypsum board,
ALC (autoclaved lightweight cellular
concrete), concrete block, plywood
less than 25.4 mm (1 inch) thick, etc.
R Use only the supplied Panasonic AC
adaptor PNLV236.
1 R
emove the rear cover by
pressing the upper sides of the
cover (A) and sliding it down (B).
A
B
2 A
ttach the rear cover to the wall by
using screws (
1
).
R P
lace the rear cover with “UP”
mark facing upwards.
R
2
37 mm (1 15/32 inches)
2
1
1
U
P
UP
10
For a
ssistance, please visit http://shop.panasonic.com/support
Setup
HNS105_(en_en)_0206_ver.111.pdf 10 2017/02/06 12:06:44
3 U
se the DC extension cord (A) to
connect the AC adaptor (B) to the
siren.
R Insert the male plug of the DC
extension cord (C) firmly into
the DC jack (D, E).
R Insert the female plug of the DC
extension cord (F) firmly into
the AC adaptor plug (G).
4 Connect the AC adaptor to the
power outlet (H).
5
8
6
7
4
1
3
2
5 A
ttach the siren to the rear cover.
R Insert the grooves on the siren
to the 4 tabs on the rear cover,
and then push down the siren.
Note:
W
hile the siren is sounding or the
strobe light is flashing, you can stop the
siren by pressing M
N.
Note about power
connections
AC adaptor connection
R T
he AC adaptor must remain
connected at all times. (It is normal
for the adaptor to feel warm during
use.)
R The AC adaptor should be
connected to a vertically oriented or
floor-mounted AC outlet. Do not
connect the AC adaptor to a
ceiling-mounted AC outlet, as the
weight of the adaptor may cause it
to become disconnected.
Power failure
R T
he siren will not work during a
power failure.
For a
ssistance, please visit http://shop.panasonic.com/support
11
Setup
HNS105_(en_en)_0206_ver.111.pdf 11 2017/02/06 12:06:44
Testing the siren
After you have installed the [Home
Network] app on your mobile device,
you can use your mobile device to test
the siren. For more information, refer to
the User’s Guide (page 12).
1 Start the [Home Network] app,
and tap [Settings].
2 Tap [Device Profiles].
3 Tap [Siren] and then select the
desired siren.
4 Tap [Installation Test].
5 Tap [Play].
Adjusting the siren’s
v
olume
You can adjust the siren’s volume
using the siren’s MHIGHN/MLOWN switch
(page 7).
Features available
w
hen using the
[Home Network] app
Some of the siren’s features that are
available when using the [Home
Network] app are listed below. For
more information, refer to the User’s
Guide (page 12).
– Alarm system
You can use the app to arm and
disarm the alarm system, confirm
the current status of the system’s
devices, and view a log of previous
events. You can also use the app to
stop the siren from sounding.
– D
evice management
You can use the app to confirm the
wireless signal strength of the siren,
change the siren’s name, change
whether the siren sounds, flashes,
or both, and test the siren.
Accessing the User’s
G
uide
The User’s Guide is a collection of
online documentation that helps you
get the most out of the [Home
Network] app.
1 iPhone
®
/iPad
®
Tap
in the app’s home screen.
A
ndroid™ devices
Tap
or press your mobile
d
evice’s menu button in the app’s
home screen.
2 Tap [User’s Guide].
Note:
R Microsoft
®
Windows
®
Internet
Explorer
®
8 and earlier versions are
not supported.
R Android 4.1 or later versions are
recommended.
R You can also access the User’s
Guide at the web page listed below.
www.panasonic.net/pcc/support/tel/
h
omenetwork/manual/
12
For a
ssistance, please visit http://shop.panasonic.com/support
Appendix
HNS105_(en_en)_0206_ver.111.pdf 12 2017/02/06 12:06:45
Specifications
R Standards
DECT (Digital Enhanced Cordless
Telecommunications)
R Frequency range
DECT: 1.92 GHz – 1.93 GHz
R RF transmission power
DECT: 115 mW (max.)
R Power source
120 V AC, 60 Hz
R Power consumption
Standby: Approx. 1.5 W
Maximum: Approx. 2.5 W
R Alert tone volume
Approx. 110 dB (High alert level)
(measured approx. 10 cm
(3 15/16 inches) from the product)
R Operating conditions
0 °C – 40 °C (32 °F – 104 °F)
R Dimensions (height ´ width ´
depth)
Approx. 71 mm ´ 73 mm ´ 46 mm
(2 13/16 inches ´ 2 7/8 inches ´
1 13/16 inches)
R Mass (weight)
Approx. 90 g (0.20 lb)
For a
ssistance, please visit http://shop.panasonic.com/support
13
Appendix
HNS105_(en_en)_0206_ver.111.pdf 13 2017/02/06 12:06:45
FCC and other
information
This device complies with Part 15 of
the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
Privacy of communications may not be
ensured when using this device.
CAUTION:
Any changes or modifications not
expressly approved by the party
responsible for compliance could void
the user’s authority to operate this
device.
NOTE:
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are
designed to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates, uses, and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause
harmful interference to radio
communications. However, there is no
guarantee that interference will not
occur in a particular installation. If this
equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the
f
ollowing measures:
– Reorient or relocate the receiving
antenna.
– Increase the separation between the
equipment and receiver.
– Connect the equipment into an
outlet on a circuit different from that
to which the receiver is connected.
– Consult the dealer or an
experienced radio/TV technician for
help.
Some devices operate at frequencies
that may cause interference to nearby
TVs and VCRs. To minimize or prevent
such interference, this device should
not be placed near or on top of a TV or
VCR. If interference is experienced,
move this device further away from the
TV or VCR. This will often reduce or
eliminate interference.
FCC RF Exposure Warning:
R This product complies with FCC
radiation exposure limits set forth for
an uncontrolled environment.
R To comply with FCC RF exposure
requirements, the device must be
installed and operated 20 cm
(8 inches) or more between the
product and all person’s body.
R This product may not be collocated
or operated in conjunction with any
other antenna or transmitter.
R For body-worn operation, the device
must be used only with a
non-metallic accessory. Use of other
accessories may not ensure
compliance with FCC RF exposure
requirements.
Notice:
R FCC ID can be found inside the unit.
14
For a
ssistance, please visit http://shop.panasonic.com/support
Appendix
HNS105_(en_en)_0206_ver.111.pdf 14 2017/02/06 12:06:45
Customer services
You may also contact us directly at: 1-800-272-7033,
Monday - Friday 9 am to 9 pm;
Saturday - Sunday 10 am to 7 pm, EST.
Accessories!
http://shop.panasonic.com/support
Customer Services Directory
Shop
for all your Panasonic gear
Go to
Get everything you need to get the most out of
your Panasonic products
Accessories & Parts for your Camera, Phone, A/V
products, TV, Computers & Networking, Personal
Care, Home Appliances, Headphones, Ba!eries,
Backup Chargers & more…
For Product Informa"on, Opera"ng Assistance,
Parts, Owner’s Manuals, Dealer and Service info
go to http://shop.panasonic.com/support
For the hearing or speech impaired TTY: 1- 877-833-8855
As of June 2015
For a
ssistance, please visit http://shop.panasonic.com/support
15
Appendix
HNS105_(en_en)_0206_ver.111.pdf 15 2017/02/06 12:06:45
Limited Warranty (ONLY FOR U.S.A.)
Limited Warranty Coverage (For USA Only)
Labor
One (1) Year
Parts
One (1) Year
To submit a new repair request and for quick repair status visit our Web Site at
http://shop.panasonic.com/support
Panasonic Products Limited Warranty
Online Repair Request
Mail-In Service--Online Repair Request
If your product does not work properly because of a defect in materials or workmanship,
Panasonic Corporation of North America (referred to as “the warrantor”) will, for the length
of the period indicated on the chart below, which starts with the date of original purchase
(“warranty period”), at its option either (a) repair your product with new or refurbished parts,
(b) replace it with a new or a refurbished equivalent value product, or (c) refund your
purchase price. The decision to repair, replace or refund will be made by the warrantor.
During the “Labor” warranty period there will be no charge for labor. During the “Parts”
warranty period, there will be no charge for parts. This Limited Warranty excludes both
parts and labor for non-rechargeable batteries, antennas, and cosmetic parts (cabinet).
This warranty only applies to products purchased and serviced in the United States.
This warranty is extended only to the original purchaser of a new product which was
not sold “as is”.
Home Network System Products
microSD card (Included model only)
90 days N/A
When shipping the unit, carefully pack, include all supplied accessories listed in the
Owner’s Manual, and send it prepaid, adequately insured and packed well in a carton box.
When shipping Lithium Ion batteries please visit our Web Site at
http://shop.panasonic.com/support as Panasonic is committed to providing the most up to
date information. Include a letter detailing the complaint, a return address and provide a
daytime phone number where you can be reached. A valid registered receipt is required
under the Limited Warranty.
IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD, THE PURCHASER WILL
BE REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING
DATE OF PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE. CUSTOMER WILL
BE CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF
OF PURCHASE.
Product or Part Name
16
For a
ssistance, please visit http://shop.panasonic.com/support
Appendix
HNS105_(en_en)_0206_ver.111.pdf 16 2017/02/06 12:06:45
Limited Warranty Limits and Exclusions
(As examples, this excludes damages for lost time, travel to and from the servicer,
loss of or damage to media or images, data or other memory or recorded content.
The items listed are not exclusive, but for illustration only.)
This warranty ONLY COVERS failures due to defects in materials or workmanship,
and DOES NOT COVER normal wear and tear or cosmetic damage. The warranty
ALSO DOES NOT COVER damages which occurred in shipment, or failures which
are caused by products not supplied by the warrantor, or failures which result from
accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty
installation, set-up adjustments, misadjustment of consumer controls, improper
maintenance, power line surge, lightning damage, modification, introduction of sand,
humidity or liquids, commercial use such as hotel, office, restaurant, or other business
or rental use of the product, or service by anyone other than a Factory Service Center
or other Authorized Servicer, or damage that is attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER
“LIMITED WARRANTY COVERAGE”.
THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT
OF ANY BREACH OF THIS WARRANTY.
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF
MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.
PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY,
ARE YOUR RESPONSIBILITY.
Some states do not allow the exclusion or limitation of incidental or consequential damages,
or limitations on how long an implied warranty lasts, so the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary
from state to state. If a problem with this product develops during or after the warranty period,
you may contact your dealer or Service Center. If the problem is not handled to your
satisfaction, then write to:
Consumer Affairs Department
Panasonic Corporation of North America
661 Independence Pkwy
Chesapeake, VA 23320
As of June 2015
For a
ssistance, please visit http://shop.panasonic.com/support
17
Appendix
HNS105_(en_en)_0206_ver.111.pdf 17 2017/02/06 12:06:45
18
Notes
HNS105_(en_en)_0206_ver.111.pdf 18 2017/02/06 12:06:45
19
Notes
HNS105_(en_en)_0206_ver.111.pdf 19 2017/02/06 12:06:45
A
B
Reconnect the AC adaptor to the siren.
If your product is not working properly. . .
IMPORTANT!
Visit our Web site: http://shop.panasonic.com/support
• FAQ and troubleshooting hints are available.
Use the Home Network app to access the User’s Guide
and refer to the Troubleshooting section.
For your future reference
W
e recommend keeping a record of the following information to assist
with any repair under warranty.
Serial No. Date of purchase
(found inside the unit)
N
ame and address of dealer
Attach your purchase receipt here.
Two Riverfront Plaza, Newark, NJ 07102-5490
© Panasonic Corporation 2015
HNS105_(en_en)_0206_ver.111.pdf 20 2017/02/06 12:06:45
Guía de instalación
Sistema de red doméstico
Sirena de interior
Modelo n° KX-HNS105
Gracias por adquirir un producto Panasonic.
Este documento explica cómo instalar la sirena de interior de forma correcta.
Para obtener detalles sobre cómo usar el sistema, consulte la Guía del usua-
rio (página 8).
Lea este documento antes de usar la unidad, y guárdelo para consultarlo en el
futuro. Para obtener ayuda, comuníquese con nosotros llamando al
1-800-272-7033 o visite nuestro sitio web: http://shop.panasonic.com/
support para clientes en los EE. UU. (solo en inglés)
Por favor, registre su producto: http://shop.panasonic.com/support
Para utilizar este dispositivo:
R Descargue la versión más reciente de la aplicación [Home Network].
R Actualice el hub a la versión de firmware más reciente (versión 5.00 o
posterior). Para obtener más información, consulte la Guía del usuario
(página 8).
PNQX7271YA CC0215WK1126 (E)
HNS105_(es_es)_0202_ver.101.pdf 1 2017/02/02 15:35:40
Configuración
Nombres de los componentes y
funciones .........................................3
Led indicador ...................................3
Resumen de configuración ..............3
Registro de la sirena ........................4
Confirmación del área de uso ..........5
Instalación .......................................6
Nota acerca de las conexiones de
alimentación ....................................7
Apéndice
Prueba de la sirena .........................8
Ajuste del volumen de la sirena .......8
Acceso a la Guía del usuario ...........8
2
Tabla de Contenido
HNS105_(es_es)_0202_ver.101.pdf 2 2017/02/02 15:35:40
Nombres de los
componentes y
funciones
A B
D
E
F
C
Altavoz
Luz estroboscópica
Parpadea cuando la sirena está
sonando.
Led indicador
MHIGHN/MLOWN (Alta/baja)
Se usa para ajustar el volumen de la
sirena (página 8).
Tapa posterior
M N
Se usa para registrar la sirena en el
hub.
Led indicador
Puede usar el Led indicador para confirmar
el estado de la sirena.
Indicador Estado
Verde, en-
cendido
Funcionamiento normal
Rojo, parpa-
deando len-
tamente
La sirena no está registra-
da en el hub
Rojo, parpa-
deante
La sirena está fuera del
alcance del hub
Rojo, parpa-
deo rápido
Se disparó el sistema de
alarma
Verde, par-
padeando
lentamente
Modo de registro (Opri-
mió y mantuvo oprimido
M
N)
Apagado Sin energía
Resumen de
configuración
1 Configuración inicial
Asegúrese de poder acceder al
sistema mediante su dispositivo móvil.
Para obtener más detalles, consulte la
Guía de configuración del sistema que
viene con su hub.
2 Registro
Solo se requiere si se compró la
sirena por separado (es decir, no
como parte de un paquete).
3 Confirme el área de instalación
Lea la información de este documento
para confirmar que el área d
e
instalación deseada sea la adecuada
para el correcto funcionamiento.
Para obtener ayuda, visite http://shop.panasonic.com/support
3
Configuración
HNS105_(es_es)_0202_ver.101.pdf 3 2017/02/02 15:35:40
4 Instalación
Instale la sirena en la ubicación
deseada.
Registro de la sirena
Este procedimiento no es necesario para
unidades que son parte de un paquete.
Antes de poder usar la sirena, debe
registrarla en el hub.
Si compró los dispositivos por separado (es
decir, no como parte de un paquete), debe
registrar cada dispositivo en el hub.
Puede registrar cada unidad mediante los
botones de registro o la aplicación [Home
Network].
Nota:
R Antes de registrar la sirena, asegúrese
que todos los adaptadores de corriente
del hub y la sirena estén conectados y
cada dispos
itivo reciba alimentación.
Uso de los botones de registro
1 Hub:
Oprima y mantenga oprimido M
OTHER DEVICEN hasta que el Led
indicador parpadee lentamente en
verde.
2 Sirena:
Oprima y mantenga oprimido M
N
hasta que el Led indicador parpadee
lentamente en verde (página 3).
R Cuando se ha completado el
registro, el hub emitirá un pitido
largo.
Nota:
R Para cancelar sin registrar la sirena,
oprima M N en el hub y en la sirena
nuevamente.
R Si el registro falla, el hub emitirá varios
pitidos cortos.
Uso de la aplicación
Cuando registre la sirena con la aplicación
[Home Network], puede asignar un
nombre a sus dispositivos y agruparlos por
ubicación. Para obtener más información,
consulte la Guía del usuario (página 8).
4
Para obtener ayuda, visite http://shop.panasonic.com/support
Configuración
HNS105_(es_es)_0202_ver.101.pdf 4 2017/02/02 15:35:40
Confirmación del área
de uso
Alcance de la comunicación
inalámbrica
El alcance de la comunicación inalámbrica
de cada dispositivo en el sistema del hub
es de aproximadamente 50 m (160 pies) en
interiores y de aproximadamente 300 m
(1,000 pies) en el exterior. Es posible que la
comunicación inalámbrica no sea tan
confiable cuando se encuentran los
obstáculos siguientes entre el hub y otros
dispositivos.
R Puertas o pantallas metálicas
R Par
edes que contengan aislamiento de
aluminio
R Paredes de hormigón o hierro corrugado
R Ventanas de vidrio doble
R Varias paredes
R Cuando los dispositivos están en pisos o
edificios diferentes
Nota:
R Puede usar el Led indicador de la sirena
para confirmar el estado de
comunicación de la sirena (página 3). Si
el Led indicador está encendido en
verde o parpadea rápidamente en rojo,
la sirena se está comunicando
correc
tamente con el hub.
Precauciones respecto al área
de uso
Usar la sirena en las siguientes áreas
puede causar deformación, averías o fallas
de operación.
R A la luz del sol
R En áreas expuestas a grasa o vapor,
como en cocinas
R Cerca del fuego o calefactores
R Cerca de campos magnéticos (como
cerca de hornos microondas e imanes)
R Áreas sujetas a cambios extremos de
temperatura, como cerca de aires
acondicionados
R Áreas con objetos reflectivos, como
vidrios, que pueden interferir con la
detección de la variación de temperatura
R Áreas donde objetos de iluminación
afectan la temperatura (como luces
fluorescentes)
R Cerca de dispositivos que emiten ondas
de radio potentes, como teléfonos
móviles
Para obtener ayuda, visite http://shop.panasonic.com/support
5
Configuración
HNS105_(es_es)_0202_ver.101.pdf 5 2017/02/02 15:35:40
Instalación
Coloque la sirena en una pared mediante
los agujeros de la tapa posterior.
Nota:
R La luz estroboscópica parpadea cuando
suena la sirena. Coloque la sirena en un
lugar donde su luz estroboscópica sea
visible.
R Monte la sirena en una ubicación
estable donde se pueda sostener con
seguridad.
R Coloque la sirena de forma segura en
una pared. Las vibraciones pueden
provocar que la sirena se caiga si esta
n
o se asegura.
R No coloque la sirena sobre un material
blando. Podría caerse, romperse o
provocar lesiones.
R No monte la sirena en las siguientes
ubicaciones: tablas de yeso, hormigón
celular, bloques de hormigón,
contrachapados con grosor inferior a
25.4 mm (1 pulgadas), etc.
R Use solo el adaptador de corriente
alterna Panasonic PNLV236 que se
suministra.
1 Extraiga la tapa posterior ejerciendo
presión sobre los lados superiores de
la misma (A) y deslícela hacia abajo
(B).
A
B
2 Instale la tapa posterior en la pared
con tornillos (
1
).
R Coloque la tapa posterior con la
marca “UP” hacia arriba.
R
2
37 mm (1 15/32 pulgadas)
2
1
1
U
P
UP
6
Para obtener ayuda, visite http://shop.panasonic.com/support
Configuración
HNS105_(es_es)_0202_ver.101.pdf 6 2017/02/02 15:35:40
3 Use el alargue de CC (A) para
conectar el adaptador de corriente
(B) a la sirena.
R Inserte el enchufe del alargue de
CC (C) firmemente en el conector
de CC (D, E).
R Inserte la ficha hembra del alargue
de CC (F) firmemente en el
enchufe del adaptador de corriente
(G).
4 Conecte el adaptador de corriente a la
toma de corriente (H).
5
8
6
7
4
1
3
2
5 Coloque la sirena en la tapa posterior.
R Inserte las 4 lengüetas de la tapa
posterior en los canales de la
sirena y luego ejerza presión hacia
abajo sobre la sirena.
Nota:
Mientras suena la sirena o la luz
estroboscópica está parpadeando, puede
oprimir M
N para detener la sirena.
Nota acerca de las
conexiones de
alimentación
Adaptador de corriente alterna
R El adaptador de corriente debe
permanecer conectado en todo
momento (es normal que el adaptador
se caliente durante su uso).
R El adaptador de corriente debe estar
conectado a un enchufe de corriente
orientado verticalmente o en una toma
de corriente alterna colocada en el piso.
No conecte el adaptador de corriente
alterna a una toma de corriente montada
en el techo, ya que el
peso del
adaptador puede hacer que se
desconecte.
Falla en el suministro eléctrico
R La sirena no funciona durante las fallas
del suministro eléctrico.
Para obtener ayuda, visite http://shop.panasonic.com/support
7
Configuración
HNS105_(es_es)_0202_ver.101.pdf 7 2017/02/02 15:35:40
Prueba de la sirena
Después de instalar la aplicación [Home
Network] en su dispositivo móvil, puede
usarlo para probar la sirena. Para obtener
más información, consulte la Guía del
usuario (página 8).
1 Inicie la aplicación [Home Network] y,
luego, oprima [Configuración].
2 Toque [Ajustes de dispositivos].
3 Oprima [Sirena] y, luego, seleccione
la sirena deseada.
4 Toque [Prueba de instalación].
5 Toque [Reproduci
r].
Ajuste del volumen de
la sirena
Puede ajustar el volumen de la sirena con
el interruptor MHIGHN/MLOWN de la sirena
(página 3).
Acceso a la Guía del
usuario
La Guía del usuario es una colección de
documentación en línea que lo ayuda a
aprovechar al máximo la aplicación [Home
Network].
1 iPhone
®
/iPad
®
Toque
en la pantalla de inicio de
la aplicación.
Dispositivos Android™
Toque
u oprima el botón menú de
su dispositivo en la pantalla de inicio
de la aplicación.
2 Toque [Guía del Usuario].
Nota:
R No se admite Microsoft
®
Windows
®
Internet Explorer
®
8 y versiones
anteriores.
R Se recomienda Android 4.1 y versiones
posteriores.
R También puede acceder a la Guía del
usuario mediante la página web a
continuación.
www.panasonic.net/pcc/support/tel/
homenetwork/manual/
8
Para obtener ayuda, visite http://shop.panasonic.com/support
Apéndice
HNS105_(es_es)_0202_ver.101.pdf 8 2017/02/02 15:35:40
9
Notas
HNS105_(es_es)_0202_ver.101.pdf 9 2017/02/02 15:35:41
10
Notas
HNS105_(es_es)_0202_ver.101.pdf 10 2017/02/02 15:35:41
11
Notas
HNS105_(es_es)_0202_ver.101.pdf 11 2017/02/02 15:35:41
HNS105_(es_es)_0202_ver.101.pdf 12 2017/02/02 15:35:41
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
Panasonic KX-HNS105 El manual del propietario
- Tipo
- El manual del propietario
- Este manual también es adecuado para
En otros idiomas
- English: Panasonic KX-HNS105 Owner's manual
Documentos relacionados
-
Panasonic KXHNA101 Instrucciones de operación
-
-
-
-
-
-
-
-
-