ROOMS TO GO 32221602 Assembly Instructions
- Tipo
- Assembly Instructions
LIN08
LIN07
DRESSER/MIRROR
ASSEMBLY INSTRUCTIONS
Important:
Be sure to check all packing material carefully for small parts which may come loose inside carton
during shipment. Separate, identify and count all parts and metal hardware.
Compare with parts list and hardware illustrations to be sure all parts are present. If any part(s) are missing or
damage, contact your dealers customer services deparment. For efficient and fast service, please indicate
the model number and the parts needed.
ATTENTION:
Some lettered parts listed on the instruction sheets may not be in the parts bag, they
may already be assembled.
TOOLS REQUIRED
(Not included)
Phillips Screwdriver
MODEL No.
EACH UNIT SOLD SEPARATELY
LIN08-
HARDWARE:
WARNING INSTALL FURNITURE TIPPING RESTRAINT KIT
PAGE 1 OF 3
Support Mirror
Part No.HB-30
(2Pcs)
INSTALLED
LIN07-
C
B
A
216 / 32221602
216 / 32121600
Bolt 8 x 32 x 1 1/4"
Part No.HCPP-14A
4 Pcs.
INSTALLED
Bolt 8 x 32 x 1 1/4"
Part No.HCPP-14A
4 Pcs.
Screw 8 x 1 1/8"
Part No.HCPF-8118
2 Pcs
HCPF-8118
DETAIL L
SCALE 1 : 4
HCPP-14A
DETAIL M
SCALE 1 : 3
HCPP-14A
HB-30
DETAIL N
DETAIL P
SCALE 1 : 3
HCPP-14A
DRESSER/MIRROR
ASSEMBLY INSTRUCTIONS
MODEL No.
LIN07
LIN08
PAGE 2 OF 3
Remove the mirror supports from unit mirror. See diagram.
A
A
A
B
B
B
B
B
A
B
B
C
C
B
B
B
C
-216 / 32221602
-216 / 32121600
Align the mirror supports with the holes, Secure with bolts 8-32 x
1 1/4" . See diagram.
Align supports with the holes on the mirror. Secure with bolt 8-32
x 1 1/4" and pan head screw 8 x 1 1/8" . See diagram.
Part No HB-488 (1PC)
(Included in the carton# LIN07-
193)
Back View Furniture
ANTI-TIP
Installation instructions:
This tip restraint must be attached to wall stub using 2” screw enclosed
1.Attach a bracket securely to the back top rail of the furniture using the 5/8” screw provided through the smaller hole.
2. Locate the other bracket on the wall over the wall stud and 2 inches below the mounting bracket secure to the back of
your unit. Attach to the wall stud using the 2’’ screw provided, through the smaller hole.
3. Place the furniture into position so both mounting brackets are vertically in line
4. Laces the end of the restraint strap though the larger hole in each mounting bracket. Bring both ends together and
slide the flat end through the looking end and flat draw it through until all slack is removed.
5. Confirm that the strap in securely laced and lacked.
Instrucciones de instalacion:
Este seguro contra volcado debe fijarse a un taco de pared con el tornillo de 2” que se incluye.
1. Coloque un soporte firmemente en la parte superior trasera del mueble ,usando el tornillo 5/8” que se proporciona y el
agujero mas pequeño
2. Ubique el otro soporte en la pared sobre un taco y 5cm (2pulg.) por debajo del soporte de montaje asegurado en la
parte bracera de la unidad .Fije al taco de pared usando el taco de 2’’ que incluye y el agujero mas pequeño .
3. Coloque el mueble en el sitio, de modo de modo que los dos soportes estén en una línea vertical.
4. Pase el extremo de una cinta de sujeción por el agujero más grande en cada soporte de montaje, una los dos
extremos y deslice el extremo plano por el lado del cierre, hasta que quede tenso.
5. Confirme que la cinta este bien asegurada.
Instructions d` installation:
Ce dispositif de sécurité doit être fixé au montai d` un mur a` l` aide de la vis de 5cm (2 po) fournie
1. fixer solidement un support a`la traversé supérieure du meuble, en passant la vis de 1,6cm (5/8 po) dans le plus petit
trou.
2. placer I` autre support sur un montant du mur, a` environ 5cm (po) plus bas, par rapport au premier support de fixation,
fixer ce support en passant la vis de 5cm (2 po) fournie dans le plus petit trou.
3. positionner le meuble afin d`aligner verticalement les deux supports de fixation
4. passer l`extrémité de i`attache dans les plus grands trous des deux supports. Joindre les extrémités insérer l`extrémité
plate dans le dispositif de blocage puis tirer au maximum pour desserrer.
5. vérifier que l`attache est solidement fixée et bloquée.
Warning Advertencia Avertissement
WARNING INSTALL FURNITURE TIPPING RESTRAINT KIT
PAGE 3 OF 3
-
1
-
2
-
3
ROOMS TO GO 32221602 Assembly Instructions
- Tipo
- Assembly Instructions
en otros idiomas
- français: ROOMS TO GO 32221602
- English: ROOMS TO GO 32221602
Artículos relacionados
-
ROOMS TO GO 26225006 Assembly Instructions
-
-
-
-
-
-
-
-
-
