Modern Forms PD-28807 Cosmic Instrucciones de operación

Tipo
Instrucciones de operación
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
1
INSTALLATION INSTRUCTION
288- Pendant
PD-28807, PD-28812
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out
or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les règlements
locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDEs
- Toutes les pièces doivent être utilisées tel quil est indiqué dans ces instructions. Ne remplacez pas les pièces, nen laissez pas de côté et
ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du luminaire.
MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e instalación de esta lámpa-
ra.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de alimentación principal
en la posición OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación ETL/CETL esta lámpara.
PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
HARDWARE
Wire Connector
Qty: 3pcs +1 Extra
7EAC112201
A
Wood Screw
Qty: 4pcs +1 Extra
7MPF2204J2
Φ4×22mm
Nickel Plating
C
Junction Box Screw
Qty: 2pcs +1 Extra
7MPF0415C2
#8-32×9/16 SS
D
Mounting Screw
Qty:1 Extra
7MPF0412C2NIH
5/32”-32×1/4
Nickel Plating
E
Plastic Anchor
Qty: 4pcs +1 Extra
7TDD082401
B
G0
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
2
PREPARATION
1. Shut o the power at the circuit breaker and remove
existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the
parts on a clear area. Be careful not to lose any small parts
necessary for installation.
CONNECTING THE WIRES (Fig. 2)
3. Remove the mounting screw (E) from the xture.
4. Install the mounting back plate to the junction box using
junction box screws (D).
5. Mark the four wood screw mounting holes on the ceiling,
remove mounting back plate, drill holes and insert the
four plastic anchors (B).
6. Adjust the xture wire length by pushing the cable
gripper on the canopy and pulling the wire as desired.
a. Retract these wires close to a desirable length to within
the canopy before securing the fixture in place.
Using the cable gripper to adjust more than 18" of wire
length is not desirable.
b. Warning: Shortening these cables without professional
helps or electronic background is not advisable.
Any modifications to the fixture will result in voiding the
warranty of the product.
7. Connect the Driver’s input wires to junction box wires
as shown in Fig. 2, making sure that all wire connectors
(A) are secured. If your outlet box has a green or bare
copper ground wire, connect the xture’s ground wire to
it. Otherwise, connect the xtures ground wire directly to
the back plate using the green screw provided. After wires
are connected, tuck them carefully inside the junction box.
MOUNTING THE FIXTURE (Fig. 1)
Install mounting plate back to the junction box using
junction box screws (D), fasten it to the ceiling using the
four wood screws (C). The side of the mounting plate
marked GND” must face out.
9.
Hook the two safety cable to the mounting plate.
10.
Push the xture onto the mounting back plate AND rotate
the xture until it is docked in position, and secure it with
mounting screws (E).
11.
Remove the nut, take apart the cover. Insert the bracket
with LED module into the glass shade; place the cover
back on the top of the glass. Secure the bracket and cover
with nut.
12.
Other glasses installation method as shown in step
INSTALLATION INSTRUCTION
288- Pendant
PD-28807, PD-28812
G0
Fig.1 Mount on Switch Box
A
B
C
D
E
Junction Box
Wire Connector
Ground Wire
Plastic Anchor
Mounting Backplate
Wood Screw
Junction Box Screw
Safety Cable
Rotate
Push
Cable Gripper
Push Up
Instruction: Adjust
the xture wire
length by pushing
the cable gripper
on the canopy and
pulling the wire as
desired.
Mounting Screw
Nut
Cover
Bracket
Glass
RPL-GLA-28801
Driver 2 3/4” L X 1 1/4” W X 1 3/16” H
Fig. 2 Wiring
Fixture Wires House Wires
Black or Black
Smooth (Hot)
Fixture Wires House Wires
White or White
Ribbed (Neutral)
Fixture Wires House Wires
Bare wire Green or Bare Copper
(Ground) (Ground)
Mounting Backplate
7MBC362001
14 1/2”
1 3/4” 3 11/16” 12 5/8”
1 3/8”
Driver
I
nput
Out
put
Black
- Hot White -
Neutral
Driver
I
nput
Out
put
Black
- Hot White -
Neutral
-+ -+
Black
- Hot White -
Neutral
Driver
I
nput
Out
put
Black
- Hot White -
Neutral
-+
Driver
I
nput
Out
put
Black
- Hot White -
Neutral
-+
Driver
I
nput
Out
put
Black
- Hot White -
Neutral
Driver
I
nput
Out
put
Black
- Hot White -
Neutral
-+ -+
Black
- Hot White -
Neutral
Driver
I
nput
Out
put
Black
- Hot White -
Neutral
-+
Driver
I
nput
Out
put
Black
- Hot White -
Neutral
-+
Driver
I
nput
Out
put
Black
- Hot White -
Neutral
-+
Driver
I
nput
Out
put
Black
- Hot White -
Neutral
-+
PD-28807 PD-28812
LED Diagram
8.  Please follow these if shortening the wire is needed. Take note or
take picture of how the wires are being connected and label each wire
clearly. Using the as given below as reference.
12.
13.
Fig.3 Diagram
Fig.3
  • Page 1 1
  • Page 2 2

Modern Forms PD-28807 Cosmic Instrucciones de operación

Tipo
Instrucciones de operación