Modern Forms WS-W81619 Sabre Instrucciones de operación

Marca: Modern Forms

Modelo: WS-W81619 Sabre

Tipo: Instrucciones de operación

Modern Forms

www.modernforms.com

Phone (800) 526.2588 • Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive • Port Washington, NY 11050

Phone (516) 515.5000 • Fax (516) 515.5050

Western Distribution Center

1750 Archibald Ave • Ontario, CA 91761

Phone (800) 526.2588 • Fax (800) 526.2585

Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. DECEMBER, 2016 1

INSTALLATION INSTRUCTION

SABRE- Vanities & Wall Sconces

WS-W81619

HARDWARE

A1 B1 C1 D1 E1 F1 G1

Wire Connector

Qty: 3PCS+1Extra

7EAC112201

Junction Box Screw

Qty: 2 pcs + 1 Extra

7MPF0415C2

#8-32x9/16

Stainless Steel

Mounting Screw

Qty: 1pc Extra

7MPF0412S3

5/32”-32x1/2

Stainless Steel

Waterproof Washer

Qty: 1pc Extra

7TGD060301CL

Conversion Plate

Qty: 1pc

4MBA151110BA

Mounting Ring

Qty: 1pc

7MBC101501

Assembly Screw

Qty: 2pc + 1Extra

7MPF0808C1

#8-32x5/16

Nickel Plating

WARNING

IMPORTANT: NEVER attempt any work without shutting o the electricity.

- Read all instructions before installing.

- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.

- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”

the circuit breaker switch(es) that control the power to the xture or room that you are working on.

- Place the wall switch in the “OFF” position.

CAUTION

- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are

worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.

CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.

AVERTISSEMENT

IMPORTANT : Coupez l’électricité avant TOUTE manipulation.

- Lisez toutes les instructions avant d’installer.

- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les

règlements locaux.

- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt

(« OFF »).

- Placez l’interrupteur mural en position d’arrêt (« OFF »).

MISE EN GARDE

- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté

et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du

luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.

ADVERTENCIA

IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.

- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta

lámpara.

- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.

- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación

principal en la posición “OFF” (APAGADO).

- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).

PRECAUCIÓN

- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni

utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación

ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.

Modern Forms

www.modernforms.com

Phone (800) 526.2588 • Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive • Port Washington, NY 11050

Phone (516) 515.5000 • Fax (516) 515.5050

Western Distribution Center

1750 Archibald Ave • Ontario, CA 91761

Phone (800) 526.2588 • Fax (800) 526.2585

Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. DECEMBER, 2016 2

Junction Box

FIG. 2 MOUNT ON JUNCTION BOX

Back Plate Dimensions Mounting Ring Dimensions

Mounting Screw

Waterproof Washer

SwitchBox

Driver

Mounting Ring

Junction Box Screw

Mounting Plate

Assembly Screw

Conversion Plate

Input Wires

Wire Connector

Mounting Plate

Junction Box Screw

5 1/2”

2 3/8”

1 3/4”

1 3/8”

Ø3 1/4”

Ø4”

Ø2 3/4”

Driver

Fixture

FIG. 1 MOUNT ON SWITCH

INSTALLATION INSTRUCTION

SABRE- Vanities & Wall Sconces

WS-W81619

Modern Forms

www.modernforms.com

Phone (800) 526.2588 • Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive • Port Washington, NY 11050

Phone (516) 515.5000 • Fax (516) 515.5050

Western Distribution Center

1750 Archibald Ave • Ontario, CA 91761

Phone (800) 526.2588 • Fax (800) 526.2585

Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. DECEMBER, 2016 3

Junction Box

Caulking

Fig. 4 Sealing

PREPARATION

1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.

2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.

INSTALLATION

MOUNT ON SWITCH BOX (Fig. 1)

3. Remove the mounting screw (C1) and waterproof washer (D1) from the xture.

4. Connect the driver input/output wire to supply wires as shown in Fig. 3, making sure that all wire connectors (A1) are secured. If your outlet

box has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly to

the back plate using the green screw provided. After wires are connected, tuck them carefully inside the switch box.

5. Secure the mounting plate to the switch box using the junction box screw (B1). The side of the mounting plate marked “GND” must face out.

6. Place the xture over the mounting back plate, and secure it with mounting screw (C1) and water proof washer (D1).

7. To prevent moisture from entering the outlet box and causing a short, use clear caulking (i.e. indoor/outdoor silicone sealant) to outline the

outside of xture back plate where it meets the wall. Leave a space at the bottom to allow moisture to escape Fig. 4.

MOUNT ON JUNCTION BOX (Fig. 2)

3. Remove the mounting screw (C1) and waterproof washer (D1) from the xture.

4. Connect the driver input/output wire to supply wires as shown in Fig. 3, making sure that all wire connectors (A1) are secured. If your outlet

box has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly to

the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.

5. Secure the mounting ring (D1) to the junction box using the junction box screw (B1). Make sure the two holes (spacing 2-3/4”) are

horizontal as shown in Fig 2. The side of the mounting plate marked “GND” must face out.

6. Place the mounting plate and the conversion plate (E1) onto the mounting ring (F1), secure them with assembly screw (G1).

7. Place the xture over the mounting back plate, and secure it with mounting screw (C1) and water proof washer (D1).

8. To prevent moisture from entering the outlet box and causing a short, use clear caulking (i.e. indoor/outdoor silicone sealant) to outline the

outside of xture back plate where it meets the wall. Leave a space at the bottom to allow moisture to escape Fig. 4.

INSTALLATION INSTRUCTION

SABRE- Vanities & Wall Sconces

WS-W81619

Fixture Wires

Black or

Smooth

Fixture Wires

White or

Ribbed

Fixture Wires

Bare wire

(Ground)

House Wires

Black

(Hot)

House Wires

White

(Neutral)

House Wires

Green or Bare Copper

(Ground)

Fig.2 Wiring

Modern Forms

www.modernforms.com

Phone (800) 526.2588 • Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive • Port Washington, NY 11050

Phone (516) 515.5000 • Fax (516) 515.5050

Western Distribution Center

1750 Archibald Ave • Ontario, CA 91761

Phone (800) 526.2588 • Fax (800) 526.2585

Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. DECEMBER, 2016 4

INSTALLATION INSTRUCTION

SABRE- Vanities & Wall Sconces

WS-W81625/WS-W81637

HARDWARE

A1 B1 C1 D1 E1 F1 G1

Wire Connector

Qty: 3PCS+1Extra

7EAC112201

Junction Box Screw

Qty: 2 pcs + 1 Extra

7MPF0415C2

#8-32x9/16

Stainless Steel

Mounting Screw

Qty: 1pc Extra

7MPF0412S3

5/32”-32x1/2

Stainless Steel

Waterproof Washer

Qty: 1pc Extra

7TGD060301CL

Conversion Plate

Qty: 1pc

4MBA151110BA

Mounting Ring

Qty: 1pc

7MBC101501

Assembly Screw

Qty: 2pc + 1Extra

7MPF0808C1

#8-32x5/16

Nickel Plating

WARNING

IMPORTANT: NEVER attempt any work without shutting o the electricity.

- Read all instructions before installing.

- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.

- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”

the circuit breaker switch(es) that control the power to the xture or room that you are working on.

- Place the wall switch in the “OFF” position.

CAUTION

- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are

worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.

CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.

AVERTISSEMENT

IMPORTANT : Coupez l’électricité avant TOUTE manipulation.

- Lisez toutes les instructions avant d’installer.

- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les

règlements locaux.

- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt

(« OFF »).

- Placez l’interrupteur mural en position d’arrêt (« OFF »).

MISE EN GARDE

- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté

et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du

luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.

ADVERTENCIA

IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.

- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta

lámpara.

- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.

- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación

principal en la posición “OFF” (APAGADO).

- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).

PRECAUCIÓN

- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni

utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación

ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.

Modern Forms

www.modernforms.com

Phone (800) 526.2588 • Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive • Port Washington, NY 11050

Phone (516) 515.5000 • Fax (516) 515.5050

Western Distribution Center

1750 Archibald Ave • Ontario, CA 91761

Phone (800) 526.2588 • Fax (800) 526.2585

Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. DECEMBER, 2016 5

Assembly Screw

Junction Box

FIG. 2 MOUNT ON JUNCTION BOX

Back Plate Dimensions Mounting Ring Dimensions

Mounting Screw

Waterproof Washer

SwitchBox

Driver

Mounting Ring

Junction Box Screw

Mounting Plate

Conversion Plate

Input Wires

Wire Connector

Mounting Plate

Junction Box Screw

5 7/8”

2 1/2” 1 3/4”

1 3/8”

Ø3 1/4”

Ø4”

Ø2 3/4”

Driver

Fixture

FIG. 1 MOUNT ON SWITCH

INSTALLATION INSTRUCTION

SABRE Vanities & Wall Sconces

WS-W81625/WS-W81637

Modern Forms

www.modernforms.com

Phone (800) 526.2588 • Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive • Port Washington, NY 11050

Phone (516) 515.5000 • Fax (516) 515.5050

Western Distribution Center

1750 Archibald Ave • Ontario, CA 91761

Phone (800) 526.2588 • Fax (800) 526.2585

Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. DECEMBER, 2016 6