Modern Forms WS-12620 Magic Instrucciones de operación

Modern Forms
Marca
Modern Forms
Modelo
WS-12620 Magic
Tipo
Instrucciones de operación
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JULY, 2015
INSTALLATION INSTRUCTION
MAGIC
WS-12620
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local
regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or
switch ”OFF” the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts
that are worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en posi
tion d’arrêt (« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en
laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler
l’homologation ETL/CETL du luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression
à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta
lación de esta lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional
y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali
mentación principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la
instalación ni utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la
base sólo.
HARDWARE A1 B1 C1
Wire
Connector
Qty: 3
Junction Box
Screw
Qty: 2 + 1 Extra
Mounting
Screw
Qty: 1 + 1 Extra
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JULY, 2015
INSTALLATION INSTRUCTION
MAGIC
WS-12620
PREPARATION
1. Shut o the power at the circuit breaker and
remove existing xture, including the mounting hardware.
2. Carefully unpack your new xture and lay out all the parts on a
clear area. Be careful not to lose any small parts
necessary for installation.
3. Remove the mounting screws (C1) from the xture.
4. Connect the transformer input wires to supply wires as shown in
Fig. 2. Connect the driver output wires to the xture wires. red
(+) to red (+), black (-) to black (-), making sure that all wire con-
nectors secured. If your outlet box has a green or bare copper
ground wire, connect the xture’s ground wire to it. Otherwise,
connect the xture’s ground wire directly to the mounting plate
(DD) using the green screw provided. After wires are connected,
tuck them carefully inside the junction box
MOUNTING THE FIXTURE (Fig. 1)
5. Secure the mounting plate (D1) to the junction box (F1)
using the junction box screws (B1).The side of the mounting
plate marked “GND” must face out.
*Requires driver to be recessed within junction box.
6. Place the xture back plate (G1) over the mounting
plate (D1) and secure with the mounting screws (C1).
7. Thread the glass (H1) onto the xture.
H1
A1
F1B1
D1G1
C1
FIG.1
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig.2 Wiring
Glass
Fixture
Screw
Back
Plate
Mounting
Plate
Mounting
Screw Junction
Box
Driver
Output Input
Back Plate Dimensions
4 1/4”
1 3/4”
4 1/8”
1 3/8”
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JULY, 2015
INSTALLATION INSTRUCTION
MAGIC
WS-12622
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local
regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or
switch ”OFF” the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts
that are worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en posi
tion d’arrêt (« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en
laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler
l’homologation ETL/CETL du luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression
à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta
lación de esta lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional
y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali
mentación principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la
instalación ni utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la
base sólo.
HARDWARE A1 B1 C1
Wire
Connector
Qty: 3
Junction Box
Screw
Qty: 2 + 1 Extra
Mounting
Screw
Qty: 1 + 1 Extra
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JULY, 2015
INSTALLATION INSTRUCTION
MAGIC
WS-12622
PREPARATION
1. Shut o the power at the circuit breaker and
remove existing xture, including the mounting hardware.
2. Carefully unpack your new xture and lay out all the parts
on a clear area. Be careful not to lose any small parts necessary
for installation.
3. Remove the mounting screws (C1) from the xture.
4. Connect the transformer input wires to supply wires as shown
in Fig. 2. Connect the driver output wires to the xture wires.
red (+) to red (+), black (-) to black (-). Making sure that all wire
connectors secured. If your outlet box has a green or bare
copper ground wire, connect the xture’s ground wire
to it. Otherwise, connect the xture’s ground wire directly to
the mounting plate (DD) using the green screw provided.
After wires are connected, tuck them carefully inside the
junction box.
5. Secure the mounting plate (D1) to the junction box (F1) using
the junction box screws (B1).The side of the mounting plate
marked “GND” must face out.
*Requires driver to be recessed within junction box
6. Place the xture back plate (G1) over the mounting plate (D1)
and secure with the mounting screws (C1).
7. Thread the glass (H1) onto the xture.
H1
A1
F1B1
D1G1
C1
FIG.1
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig.2 Wiring
Mounting
Plate
Junction
Box
Driver
Output Input
Mounting
Screw
Mounting
Plate
Back
Plate
Fixture
Screw
Back Plate Dimensions
4 1/4”
1 3/4”
4 1/8”
1 3/8”
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Modern Forms WS-12620 Magic Instrucciones de operación

Modern Forms
Marca
Modern Forms
Modelo
WS-12620 Magic
Tipo
Instrucciones de operación
Descargar PDF
informe

En otros idiomas

Documentos relacionados