Modern Forms WS-W5516 Twilight Instrucciones de operación
- Tipo
- Instrucciones de operación
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. AUGUST, 2015
HARDWARE
A1 B1 G1
INSTALLATION INSTRUCTION
TWILIGHT
WS-W5516, W5521
Technology Upgraded
No Driver Required
Driver
(Please direct wire with 120V AC)
Wire Connector
Qty: 3
Junction Box
Screw
Qty: 2 + 1 Extra
Mounting Screw
Qty: 2 + 1 Extra
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. AUGUST, 2015
INSTALLATION INSTRUCTION
TWILIGHT
WS-W5516, W5521
PREPARATION
1. Shut o the power at the circuit breaker and remove
existing xture, including the mounting hardware.
2. Carefully unpack your new xture and lay out all the
parts on a clear area. Be careful not to lose any small
parts
necessary for installation.
MOUNTING THE FIXTURE (FIG.1)
3. Secure the mounting plate (D1) to the junction box (F1)
using junction box screws (B1). The side of the
mounting plate marked “GND” must face out.
CONNECTING THE WIRES (FIG.2)
4. Connect the electrical wires as shown in Fig. 2, making
sure that all wire connectors (A1) are secured. Fixture
and junction box ground wires should be connected
to mounting plate using green screw provided.
Tuck wires carefully inside the junction box.
5. Place the xture’s back plate over the mounting plate
(D1) and secure with screws (G1) and gasket (C1).
6. If desired, the decorative insert may be removed by
unscrewing the nut (H1) from the back of the xture
COMPLETING INSTALLATION (FIG.3)
7. To prevent moisture from entering the outlet box and
causing a short, use clear caulking (i.e. indoor/outdoor
silicone sealant) to outline the outside of xture back
plate where it meets the wall. Leave a space at the
bottom to allow moisture to escape (Fig.3).
F1
H1
A1
C1
G1
D1
B1
G1
C1
Junction Box
Wire
Connector
Gasket
Screw
Mounting Plate
Junction Box Screw
Fixture Screw
Gasket
Nut
FIG.1
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig.2 Wiring
Junction Box
Caulking
Fig.3 Sealing
Back Plate Dimensions
4 ”
1 3/4 ”
4 1/2 ”
1 3/8 ”
-
1
-
2
Modern Forms WS-W5516 Twilight Instrucciones de operación
- Tipo
- Instrucciones de operación
En otros idiomas
Documentos relacionados
-
Modern Forms WS-W22514 Kyoto Instrucciones de operación
-
-
-
-
-
-
-
-
-