Modern Forms PD-28801 Cosmic Instrucciones de operación
- Tipo
- Instrucciones de operación
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. 1
INSTALLATION INSTRUCTION
288- Pendant
PD-28801
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out
or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les règlements
locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDEs
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté et
ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du luminaire.
MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e instalación de esta lámpa-
ra.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de alimentación principal
en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación ETL/CETL esta lámpara.
PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
HARDWARE
Wire Connector
Qty: 3pcs+1 Extra
7EAC112201
A
Mounting Screw
Qty: 1 Extra
7MPF0313S1
1/8-40x1/2
Nickel Plating
C
Wire Connector
Qty: 2pcs+1 Extra
7EAC140901
D
DRIVER
Qty: 1pcs
4LD-350MA14U-IS-P
E
Junction Box Screw
Qty: 2pcs+1 Extra
7MPF0820C1
#8-32x13/16
Nickel Plating
B
G0
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. 2
PREPARATION
1. Shut o the power at the circuit breaker and
remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all
the parts on a clear area. Be careful not to lose any
small parts necessary for installation.
CONNECTING THE WIRES (Fig. 2)
3. Remove the mounting screw (C) from the xture.
4. Adjust the xture wire length by pushing the cable
gripper on the canopy and pulling the wire as
desired.
5. Connect the Driver’s input wires to junction box
wires as shown in Fig. 2, making sure that all wire
connectors (A) are secured. If your outlet box has
a green or bare copper ground wire, connect the
xture’s ground wire to it. Otherwise, connect the
xture’s ground wire directly to the back plate
using the green screw provided. After wires are
connected, tuck them carefully inside the junction
box.
*Requires Driver to be recessed within the
junction box
MOUNTING THE FIXTURE (Fig. 1)
6. Secure the mounting back plate to the junction
box using junction box screws (B).The side of the
mounting back plate marked “GND” must face out.
7. Place the xture over the mounting plate and
secure it with mounting screws (C).
8. Remove the nut, take apart the cover. Insert the
bracket with LED module into the glass shade;
place the cover back on the top of the glass. Secure
the bracket and cover with nut.
INSTALLATION INSTRUCTION
288- Pendant
PD-28801
G0
Mounting Backplate
7MBC120803
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring
Fig.1 Mount on Switch Box
B
A
C
D
E
Junction Box
Wire Connector
Driver 2 3/4” L X 1 1/4” W X 1 3/16” H
Mounting Back Plate
Junction Box Screw
Mounting Screw
Canopy
Wire Connector
Cable Gripper
Push Up
Instruction: Adjust
the xture wire length
by pushing the cable
gripper on the canopy
and pulling the wire
as desired.
Nut
Cover
Bracket
Glass
RPL-GLA-28801
Ø1 3/4”
1 3/8”
1 3/4”
-
1
-
2
Modern Forms PD-28801 Cosmic Instrucciones de operación
- Tipo
- Instrucciones de operación
En otros idiomas
Documentos relacionados
-
Modern Forms PD-64849 Chaos Instrucciones de operación
-
-
-
-
-
-
-
-
-
