LG LSWS306ST Guía de instalación

Marca: LG

Modelo: LSWS306ST

Tipo: Guía de instalación

INSTALLATION MANUAL

ELECTRIC CONVECTION

BUILT-IN OVEN

Please read these instructions thoroughly before

installing and operating the oven.

LWS3081ST

LWD3081ST

LWS3010ST

LWD3010ST

LWS3063ST

LWD3063ST

LSWS306ST

LSWD306ST

LWS3063BD

LWD3063BD

LSWS309BD

LSWD309BD

www.lg.com

ENGLISH

ESPAÑOL

MFL69713801_00

- 2 -

BEFORE BEGINNING

Remove all tape and packing materials before using the oven. Dispose of all plastic bags after unpacking the oven.

Never allow children to play with packing materials.

You can download an installation manual at http://www.lg.com.

IMPORTANT SAFETY INSTRUCTIONS

Read and follow all instructions before using the oven to prevent the risk of fire, electric shock, injury to persons,

or damage when using the oven. This guide does not cover all possible conditions that may occur. For further

assistance contact the service agent or manufacturer.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “WARNING” or “CAUTION”.

These words mean :

WARNING

This symbol will alert you to hazards or unsafe practices which could cause serious bodily

harm or death.

CAUTION

This symbol will alert you to hazards or unsafe practices which could cause bodily injury or

property damage.

SAFETYPart 1

• The information in this manual should be followed exactly.

- Failure to do so could result in fire or electrical shock, causing property damage, personal injury

or death.

• DO NOT put any weight on the oven door. Never allow anyone to climb, sit, stand or

hang on the oven door.

- The oven could be tipped and injury might result from contact with hot food or the oven itself.

• The electrical power must be shut off while the electrical connections are being

made.

- Failure to do so can result in severe personal injury, death or electrical shock.

• New branch-circuit installations (1996 NEC), mobile homes, recreational vehicles,

or installations where local codes prohibit grounding through the neutral conductor

require 4-wire branch-circuit connection.

• Improper connection of aluminum house wiring to copper leads can result in

an electrical hazard or fire. Use only connectors designed for joining copper to

aluminum and follow the manufacturer’s recommended procedure closely.

• Mounting screws must be used.

- Failure to do so can result in the oven falling out of the cabinet causing serious injury.

WARNING

• Make sure the cabinets and wall coverings around the oven can withstand the

temperature (up to 194˚F[90˚C]) generated by the oven.

- Discoloration, delamination or melting may occur.

• DO NOT remove spacers on the side walls of the built-in oven.

- These spacers center the oven in the space provided.The oven must be centered to prevent

excess heat buildup that may result in heat damage or fire.

• DO NOT block the oven air exhaust located at the bottom of the oven.

- Blocking the exhaust may cause cabinet damage and product malfunction.

CAUTION

- 3 -

ENGLISH

SAFETYPart 1

IMPORTANT NOTE

This installation must be completed by a qualified installer or technician.

• Please read the entire Installation Instructions prior to installation.

• Remove all packing materials from the oven compartments before connecting the electrical supply to the oven.

• Installer: please retain these instructions for local inspector’s reference, then leave them with the consumer.

• Consumer: please read and keep these instructions for future reference and be sure to read the entire

OWNER’S MANUAL prior to use.

• Do not use the parts except for provided components when you install the product.

IMPORTANT NOTE

Proper installation is the responsibility of the installer

and product failure due to improper installation is

NOT covered under warranty.

REQUIRED TOOLS

MATERIALS INCLUDED

MATERIALS NEEDED

Phillips Screwdriver

Junction Box

30’ (76.2 cm)

Metal Bottom Trim

Wire Nuts

36” (91 cm)

of String

3/4” Conduit

Connector

Drill

4X14

6 Wood Screws

For Mounting

(4 needed for installation

and 2 extra’s)

4X8

3 Screws For

Bottom Trim

(3 needed for installation)

• The information in this manual

should be followed exactly.

Failure to do so could result in fire or electrical shock,

causing property damage, personal injury or death.

WARNING

• DO NOT put any weight on the oven

door. Never allow anyone to climb,

sit, stand or hang on the oven door.

- The oven could tip and injury might result from

contact with hot food or the oven itself.

WARNING

• The electrical power must be shut off

while the electrical connections are

being made.

- Failure to do so can result in severe personal injury,

death or electrical shock.

WARNING

- 4 -

Part 2 INSTALLATION REQUIREMENTS

INSTALLATION DRAWINGS (FOR 30” SINGLE BUILT- IN OVEN)

The first step of the installation is measure the current cutout dimensions and compare them to the cutout

dimensions shown below. Little or no cabinet work may be necessary.

IMPORTANT NOTE

• The cabinet base platform must be able to support 190lbs (86kg). If the cabinet does not have a solid bottom, two

braces or runners must be installed level with the bottom of the cutout to support the weight of the oven. Make

sure the base is level and the front of the cabinet is square. If the cabinet base is not level, the oven glides will

tend to slide out when opening the door.

•

If marks, blemishes or the cutout opening are visible above the installed oven, it may be necessary to add wood

shims under the runners and front trim until the marks or opening are covered.

•

If the cabinet does not have a front frame and the sides are less than 3/4” (1.9 cm) thick, shim both sides equally

to establish the cutout width.

•

The junction box must be flush with the rear wall of the cabinet as shown below.

•

Allow at least a 23” clearance for the door depth when it is open.

• Kitchen cabinets in contact with the oven must be heat resistant up to 194°F (90°C), and fronts of nearby units up

to at least 158°F (70°C).

Product dimensions

27 3/8”

(69.5 cm)

29 5/16”

(74.5 cm)

29 3/4”

(75.5 cm)

23 3/8”

(59.3 cm)

28 7/8”

(73.3 cm)

Cutout dimensions

Junction Box

Location

23 1/2”

30”

23”

5”

28 1/2” Min.

28 5/8” Max.

23 1/2”

28 15/16” Min.

29” Max.

Minimum cutout

location from

floor 31”

Allow 1”

minimum for

overlap of oven

Allow 1”

minimum for

overlap of oven

Cabinet Width 30” (762 mm)

Recommended

Minimum

Cutout Location

from Floor 31” (787.4 mm)

Cutout Depth 23 1/2” Min. (596.9 mm)

Cutout Width 28 1/2” Min. (723.9 mm)

28 5/8” Max. (727 mm)

Cutout Height 28 15/16” Min. (735 mm)

29” Max. (736.6 mm)

- 5 -

ENGLISH

Part 2 INSTALLATION REQUIREMENTS

INSTALLATION DRAWINGS (FOR 30” DOUBLE BUILT- IN OVEN)

The first step of the installation is measure the current cutout dimensions and compare them to the cutout

dimensions shown below. Little or no cabinet work may be necessary.

IMPORTANT NOTE

•

The cabinet base platform must be able to support 325lbs (147kg). If the cabinet does not have a solid bottom,

two braces or runners must be installed level with the bottom of the cutout to support the weight of the oven.

Make sure the base is level and the front of the cabinet is square. If the cabinet base is not level, the oven glides

will tend to slide out when opening the door.

•

If marks, blemishes or the cutout opening are visible above the installed oven, it may be necessary to add wood

shims under the runners and front trim until the marks or opening are covered.

•

If the cabinet does not have a front frame and the sides are less than 3/4” (1.9 cm) thick, shim both sides equally

to establish the cutout width.

•

The junction box must be flush with the rear wall of the cabinet as shown below.

•

Allow at least a 23” clearance for the door depth when it is open.

• Kitchen cabinets in contact with the oven must be heat resistant up to 194°F (90°C), and fronts of nearby units up

to at least 158°F (70°C).

Product dimensions

27 3/8”

(69.5 cm)

52 1/16”

(132.2 cm)

29 3/4”

(75.5 cm)

23 3/8”

(59.3 cm)

51 5/8”

(131.0 cm)

Cutout dimensions

Junction Box

Location

47”

30”

23”

5”

28 1/2” Min.

28 5/8” Max.

51 13/16” Min.

51 15/16” Max.

Allow 1”

minimum for

overlap of oven

Allow 1”

minimum for

overlap of oven

23 1/2”

Minimum cutout location from floor 12”

Cabinet Width 30” (762 mm)

Recommended

Minimum

Cutout Location

from Floor 12” (304.8 mm)

Cutout Depth 23 1/2” Min. (596.9 mm)

Cutout Width 28 1/2” Min. (723.9 mm)

28 5/8” Max. (727 mm)

Cutout Height 51 13/16” Min. (1316 mm)

51 15/16” Max. (1319.2 mm)

- 6 -

Part 2 INSTALLATION REQUIREMENTS

INSTALLATION DRAWINGS (FOR 30” SINGLE BUILT- IN OVEN UNDERCOUNTER)

The first step of the installation is measure the current cutout dimensions and compare them to the cutout

dimensions shown below. Little or no cabinet work may be necessary.

IMPORTANT NOTE

• The cabinet base platform must be able to support 190lbs (86kg). If the cabinet does not have a solid bottom, two

braces or runners must be installed level with the bottom of the cutout to support the weight of the oven.

Make sure the base is level and the front of the cabinet is square. If the cabinet base is not level, the oven glides

will tend to slide out when opening the door.

• If marks, blemishes or the cutout opening are visible above the installed oven, it may be necessary to add wood

shims under the runners and front trim until the marks or opening are covered.

• If the cabinet does not have a front frame and the sides are less than 3/4” (1.9 cm) thick, shim both sides equally

to establish the cutout width.

• The junction box must be flush with the rear wall of the cabinet as shown below.

• This oven is only approved to be installed under the specific models as labeled on this unit.

• Kitchen cabinets in contact with the oven must be heat resistant up to 194°F (90°C), and fronts of nearby units up

to at least 158°F (70°C).

Product dimensions

Dimensions are the same as the single built-in oven on page 4.

Cutout dimensions

Gas and electrical connections for

30” (76.2 cm) gas cooktop must be located

in an adjacent accessible location to the

right. For a 36” (91.4 cm) gas cooktop, the

connections may be made to the left.

Gas or electric cooktops may be installed over this oven.

See cooktop installation instructions for cutout size.

See label on top of oven for approved cooktop models.

240 V / 208 V

Junction Box Location

(Junction box may be

in adjacent cabinet)

5”

25” (63.5 cm)

28 15/16” (73.5 cm) Min.

29” (73.7 cm) Max.

Allow 1” (2.5 cm)

overlap top of oven,

1/16” (1.8 cm) overlap

side edges of cutout

and 1

1/4” (3.2 cm)

overlap bottom of oven.

Top and/or side fillers

may be necessary if

unit is positioned

between existing

cabinets. Be sure they

are attached securely

since, they will anchor

the oven in the cabinets.

36” (91.4 cm)

Typical

Countertop

Height

23 1/2” (59.7 cm) Min.

Above Support

Platform

24” (61 cm)

3/4

”(7 cm) ~ 4”(10.2 cm)

28 1/2” (72.4 cm) Min.

28 5/8” (72.7 cm) Max.

- 7 -

ENGLISH

INSTALLATION REQUIREMENTSPart 2

4. Place the oven on a table or platform even with the cutout opening. (The table or platform must support 190 lbs

[86 Kg] for a single built-in oven, 325 lbs [147 Kg] for a double built-in oven.)

5. Remove the metal bottom trim from the oven. It will be installed at the end of the installation process. The trim

is wrapped separately and taped to the top of the unit.

Step. 1

Fully open the door.

Hinge

lock

Slot

Lock

Unlock

Step. 2

Pull the hinge locks up

towards the door's

frame, to the unlocked

position.

Step. 3

Firmly grasp both sides of the door at the top.

Step. 4

about 5

Close door to the door removal

position, which is approximately

5 degrees.

Step. 5

Lift door up and out until the

hinge arm is clear of the slot.

IMPORTANT NOTE

• Do not lift the door by the handle. The oven door is very

heavy. Firmly grasp the door by the sides before lifting

it off the hinges.

• Do not lay the oven door on its handle. Doing so may

cause dents or scratches.

• Use two or more people to lift or move the oven into

the cabinet opening. Use caution when lifting the oven

and wear gloves to protect hands from any sharp

edges. Failure to follow these instructions may result in

injury.

Spacer

PREPARATION FOR MOVING THE OVEN

The second step of the installation is to remove any packing material from the oven before installing the oven.

1. Remove all tape from around the oven.

2. Open the oven door and remove packaging materials and oven racks inside the oven.

3. Door removal is not a requirement for installation of the oven, but is an added convenience.

To remove the door, follow the steps below.

• Make sure the cabinets and wall

coverings around the oven can

withstand the temperature (up to

194 °F [90 °C]) generated by the oven.

- Discoloration, delamination or melting may occur.

CAUTION

• DO NOT remove spacers on the side

walls of the built-in oven.

- These spacers center the oven in the space

provided. The oven must be centered to prevent

excess heat buildup that may result in heat damage

or fire.

CAUTION

- 8 -

ELECTRICAL CONNECTIONSPart 3

ELECTRICAL CONNECTION REQUIREMENTS

The third step of the installation is to follow the electrical connection requirements below.

Ensure that dedicated circuit protection is prepared as recommended and that the oven is grounded properly.

IMPORTANT NOTE

Be sure the wall oven is installed and grounded properly by a qualified installer or service technician.

• This wall oven must be electrically grounded in accordance with local codes or, in their absence, with the

National Electrical Code ANSI/NFPA No.70- latest edition* in United States, or with CSA Standard C22.1-1982 and

C22.2 No.01982 (or latest edition)**, Canadian Electrical Code, Part1, and all local codes and ordinances.

• This wall oven must be supplied with the proper voltage and frequency, and connected to an individual, properly

grounded branch circuit, protected by a circuit breaker or fuse. To know the circuit breaker or fuse required by this

model, see the rating plate to find the wattage consumption and refer to the table below to get the circuit breaker

or fuse amperage.

Appliance Rating

Watts 240 V

Protection Circuit

recommended

Appliance Rating

Watts 208 V

Protection Circuit

recommended

less than 4800 W 20 A less than 4100 W 20 A

4800 W - 7200 W 30 A 4100 W - 6200 W 30 A

7200 W - 9600 W 40 A 6200 W - 8300 W 40 A

9600 and + 50 A 8300 and + 50 A

• A double wall oven can consume up to 7,800 W at 240 VAC.

A 40 Amp circuit breaker with wire gauge #8 AWG must be used.

• A single wall oven can consume up to 4,100 W at 240 VAC.

A 30 Amp circuit breaker with wire gauge at least #10 AWG must be used.

IMPORTANT NOTE

• Do Not ground to a gas pipe.

• Do Not have a fuse in the neutral or grounding circuit.

• A U.L.-listed conduit connector must be provided at the junction box.

• New branch-circuit installations

(1996 NEC), mobile homes,

recreational vehicles, or installations

where local codes prohibit grounding

through the neutral conductor

require 4-wire branch-circuit

connection.

WARNING

• Improper connection of aluminum

house wiring to copper leads can

result in an electrical hazard or fire.

Use only connectors designed for

joining copper to aluminum and

follow the manufacturer’s

recommended procedure closely.

WARNING

- 9 -

ENGLISH

Part 3 ELECTRICAL CONNECTIONS

ELECTRICAL CONNECTION

The fourth step of the installation is to prepare the electrical connection as follows:

1. Turn off the circuit breaker or remove fuses to the oven branch circuit.

2. With the oven positioned directly in front of the cabinet opening, connect the flexible conduit to the electrical

junction box as shown below. Position the conduit in such a manner that it will lie on top of the oven in a natural

loop when the oven is installed.

Junction Box

Location

22” Min for single wall oven

42” Min for double wall oven

Junction Box must be recessed

and conduit connector must be

used at Junction Box.

5” Min

3. If local codes permit connection of the frame grounding conductor to the neutral(white) wire, follow the

instructions for a 3-wire circuit connection on page 10.

If used in mobile homes or new construction, or a recreational vehicle, or local codes do not permit connection

of the frame grounding conductor to the neutral(white) wire, follow the instructions for a 4-wire circuit

connection on page 10.

IMPORTANT NOTE

• The wall ovens must be hard wired (direct wired) into an approved junction box. A plug and receptacle is not

permitted on these products.

• DO NOT shorten the flexible conduit. The conduit connector must be securely attached to the junction box and

the flexible conduit must be securely attached to the conduit connector. If the flexible conduit will not fit within

the connector, do not install the oven until a connector of the proper size is obtained.

NOTE TO ELECTRICIAN

The power leads supplied with the appliance are UL, CSA recognized for connection to larger gauge household

wiring. The insulation of these leads is rated at temperatures much higher than the temperature rating of

household wiring. The current carrying capacity of the conductor is governed by the wire gauge and the

temperature rating of the insulation around the wire.

- 10 -

ELECTRICAL CONNECTIONSPart 3

IMPORTANT NOTE

•

You will need to purchase an appropriate conduit connector to complete the connection of the conduit to the

junction box.

To connect to a three-wire circuit, follow these steps:

1. Connect the oven ground (green) wire and neutral

(white) wire to the branch circuit neutral (white or

gray in color) wire, using a wire nut.

2. Connect the oven red wire to the branch circuit red

(L2) wire in accordance with local codes, using a

wire nut.

3. Connect the oven black wire to the branch circuit

black (L1) wire in accordance with local codes,

using a wire nut. If the residence red, black or white

wires are aluminum conductors, see WARNING on

page 8.

4. Install the junction box cover.

To connect to a four-wire circuit, follow these steps:

1. Separate the oven ground and white wires if

necessary.

2. Connect the oven ground (green) wire to the branch

circuit ground (green) wire in accordance with

local codes, using a wire nut. If the residence red,

black or white wires are aluminum conductors, see

WARNING on page 8.

3. Connect the oven white wire to the branch circuit

neutral (white or gray in color) wire in accordance

with local codes, using a wire nut.

4. Connect the oven red wire to the branch circuit red

(L2) wire in accordance with local codes, using a

wire nut.

5. Connect the oven black wire to the branch circuit

black (L1) wire in accordance with local codes,

using a wire nut. If the residence red, black or white

wires are aluminum conductors, see WARNING on

page 8.

6. Install the junction box cover.

3-wire circuit connection

Junction Box

4-wire circuit connection

White

Green

Black

Red

Neutral

Wire nut

- 11 -

ENGLISH

INSTALL THE OVENPart 4

CABINET INSTALLATION

The fifth step of the installation is to install the oven into the cabinet as follows:

1. Sliding the oven into the opening.

a. Loop (do not tie) a 36” (91 cm) string around the conduit before the oven is slid into place.This will keep the

conduit from falling behind the oven.

b. Lift oven into cabinet cutout using the oven opening as a grip. Carefully push against the oven front frame.

Do not push against outside edges.

c. While sliding the oven back, pull the string so that the conduit lies on the top of the oven in a natural loop.

d. When you are sure the conduit is out of the way, slide the oven 3/4 way back into the opening. Remove the

string by pulling on one end of the loop.

•

DO NOT block the oven air exhaust

located at the bottom of the oven.

- Blocking the exhaust may cause cabinet damage

and product malfunction.

CAUTION

• Mounting screws must be used.

- Failure to do so can result in the oven falling out

of the cabinet causing serious injury.

WARNING

2. Securing the oven.

a. Using the mounting holes on the oven side trim as

a guide, drill pilot holes for screws provided (For

securing the double wall oven, use a minimum of

4 screws, one on each side in both the upper and

lower ovens. For securing the single wall oven, use

a minimum of 2 screws, one on each side.)

b. Secure the oven to the cabinet with screws

provided.

If the cabinet is particle board, you must use 3/4”

particle board screws. These may be purchased at

any hardware store.

3. Installing the metal bottom trim.

a. Place the metal bottom trim centered over the pre-

drilled mounting holes on the lower base.

b. Using 3 screws provided, secure the bottom trim

to the bottom edge of the cabinet.

4. Reinstalling the oven door.

Mounting

Hole

Locations

Mounting

Hole

Locations

Trim Screws

Side

Trim

Side Trim

Lower base

Metal Trim:

Correct

position

Metal Trim:

Wrong

position

Metal

bottom

trim

Step. 1

Firmly grasp both

sides of the door at

the top.

Step. 2

With the door at the

same angle as the

removal position, seat

the indentation of the

hinge arm into the

bottom edge of the

hinge slot. The notch

in the hinge arm must

be fully seated into the bottom of the slot.

Step. 3

Fully open the door. If the door will not fully open, the

indentation is not seated correctly in the bottom edge

of the slot.

Step. 4

Push the hinge locks up

against the front frame of

the oven cavity to the locked

position.

Step. 5

Close the oven door.

Hinge arm

Bottom

edge of

slot

Indentation

Hinge arm

Hinge lock

- 12 -

OPERATION CHECKLISTPart 5

CHECKING OPERATION

Each of the functions has been factory checked before shipping. However, it is suggested that you verify the

operation of the oven once more. Refer to the Owner’s Manual. Follow the instructions for the basic check.

1. Turn on power supply. The initial signal sound is heard and the LG logo appears in the display.

2. Check the operation of the broil mode. When the oven is set to broil, the upper element in the oven should

become red. After a few minutes, partially open the oven door. You should feel heat from the oven. Press CLEAR/

OFF (for model : LWS3081ST, LWD3081ST, LWS3010ST, LWD3010ST, LWS3063ST, LWD3063ST, LWS3063BD,

LWD3063BD) or adjust the oven mode knob to OFF position (for model : LSWS306ST, LSWD306ST, LSWD309BD,

LSWS309BD)

3. Check the operation of the bake mode. After setting the oven to 350 °F / 177 °C for baking, the temperature of

the oven in the display should increase. Press CLEAR/OFF (for model : LWS3081ST, LWD3081ST, LWS3010ST,

LWD3010ST, LWS3063ST, LWD3063ST, LWS3063BD, LWD3063BD) or adjust the oven mode knob to OFF position

(for model : LSWS306ST, LSWD306ST, LSWS309BD, LSWD309BD)

4. Check the operation of the convection bake mode. After setting the oven to 350 °F / 177 °C for convection

baking, the fan inside the oven should come on with the door closed. Press CLEAR/OFF (for model : LWS3081ST,

LWD3081ST, LWS3010ST, LWD3010ST, LWS3063ST, LWD3063ST, LWS3063BD, LWD3063BD) or adjust the oven

mode knob to OFF position (for model : LSWS306ST, LSWD306ST, LSWS309BD, LSWD309BD)

5. Turn on and off the oven light to check the lights are in normal condition.

6. Check the operation of the burner for each convection mode. After setting the oven to 350 °F / 177 °C for each

convection mode, the back element should light up and the fan inside the oven should come on with door

closed. (for model : LWS3081ST, LWD3081ST, LWS3010ST, LWD3010ST)

IMPORTANT NOTE

• A small amount of smoke and odor may be noticeable during the initial break-in period.

• If the oven does not operate properly or an F-, followed by a number, appears in the display, see the Owner’s

Manual for the troubleshooting list. The list includes common occurrences that are not the result of defective

workmanship or materials in this product. If the problem occurs continuously, contact the dealer.

• Refer to the warranty in the Owner’s Manual for the LG toll-free service number and address.

MANUAL DE INSTALACIÓN

HORNO ELÉCTRICO DE

CONVECCIÓN EMPOTRADO

Tenga a bien leer estas instrucciones por completo

antes de instalar y operar el horno.

LWS3081ST

LWD3081ST

LWS3010ST

LWD3010ST

LWS3063ST

LWD3063ST

LSWS306ST

LSWD306ST

LWS3063BD

LWD3063BD

LSWS309BD

LSWD309BD

www.lg.com

ESPAÑOL

P/No.: MFL69713801

- 2 -

ANTES DE COMENZAR

Quite toda la cinta y materiales de empaque antes de utilizar el horno. Deseche todas las bolsas plásticas después

de desempacar el horno. Nunca permita que los niños jueguen con los materiales de empaque.

Usted puede descargar el manual de instalación en http://www.lg.com.

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Lea y siga todas las instrucciones antes de utilizar su horno para evitar un riesgo de incendio, descarga eléctrica,

lesiones a personas o daños cuando utilice el horno. Esta guía no cubre todas las condiciones posibles que pueden

ocurrir. Para más información, comuníquese con su agente de servicios o fabricante.

Este es el símbolo de alerta de seguridad. Este símbolo lo alerta sobre peligros potenciales que pueden matarlo

a lastimarlo a usted o a otros. Todos los mensajes de seguridad se encontrarán después de los símbolos de

alerta de seguridad y de las palabras "ADVERTENCIA" O "PRECAUCIÓN". Estas palabras significan:

ADVERTENCIA

Este símbolo lo alerta sobre riesgos o prácticas poco seguras que podrían provocar

heridas corporales graves o la muerte.

PRECAUCIÓN

Este símbolo lo alerta sobre riesgos o prácticas poco seguras que podrían provocar

lesiones corporales graves o daños a la propiedad.

SEGURIDADParte 1

• La información de este manual debe seguirse al pie de la letra.

- De no hacerlo, podría provocar un incendio o una descarga eléctrica, causando daños a la propiedad,

lesiones personales o la muerte.

• NO coloque elementos pesados sobre la puerta del horno. Nunca permita que nadie se suba,

siente, pare o cuelgue de la puerta del horno.

- El horno puede volcarse y podrían generarse lesiones provocadas por los alimentos calientes o el horno.

• La energía eléctrica debe apagarse mientras se efectúan las conexiones eléctricas.

- No hacerlo puede provocar lesiones personales graves, la muerte o una descarga eléctrica.

• Las instalaciones nuevas de circuito derivado (1996 NEC), las casas rodantes, los vehículos

recreativos o las instalaciones en las que los códigos locales prohíben la conexión a tierra a

través de un conductor neutral requieren una conexión de circuito derivado de 4 hilos.

• Una conexión inadecuada de cableado doméstico de aluminio con cables de cobre puede

generar un riesgo eléctrico o un incendio. Sólo use conectores diseñados para unir cobre con

aluminio y siga al pie de la letra el procedimiento recomendado del fabricante.

• Deben utilizarse tornillos de montaje.

- Si no se hace, el horno puede caer del gabinete, lo que provocaría una lesión grave.

ADVERTENCIA

• Verifique que los gabinetes y los revestimientos de las paredes ubicados alrededor del horno

puedan soportar la temperatura (hasta 194°F [90°C]) generada por el horno.

- Puede provocarse decoloración, delaminación o fusión.

• NO quite los espaciadores de las paredes laterales del horno empotrado.

- Estos espaciadores centran el horno en el espacio provisto. El horno debe centrarse para evitar una

acumulación excesiva de calor que puede provocar daños o un incendio.

• NO bloquee la salida de aire del horno ubicada en la parte inferior del horno.

- Bloquear la salida puede provocar daños en el gabinete y el mal funcionamiento del producto.

PRECAUCIÓN

- 3 -

ESPAÑOL

SEGURIDADParte 1

NOTA IMPORTANTE

Esta instalación debe completarla un instalador o técnico calificado.

• Tenga a bien leer la totalidad de las Instrucciones de instalación antes de efectuar la instalación.

• Quite todo el material de empaque de los compartimentos del horno antes de conectar el suministro eléctrico del horno.

• Instalador: Conserve estas instrucciones para referencia del inspector local, luego déjelas con el consumidor.

• Consumidor: Lea y conserve estas instrucciones para referencia futura y asegúrese de leer todo el MANUAL DEL

PROPIETARIO antes del uso.

• No utilice partes que no sean los componentes provistos cuando instale el producto.

NOTA IMPORTANTE

Una instalación adecuada es responsabilidad del

instalador y la garantía NO cubre las fallas del

producto debido a una instalación incorrecta.

PREPARACIÓN PARA INSTALAR EL

HORNO

PREPARACIÓN PARA INSTALAR EL

HORNO

MATERIALES NECESARIOS

Destornillador Phillips

Caja de

conexiones

30” (76.2 cm)

Reborde inferior de metal

Tapones de

alambre

36” (91 cm) de hilo

Conector de

conducto de 3/4"

Perforadora

4X14

6 tornillos de madera

para el montaje

(4 necesarios para la

instalación y 2 extra)

4X8

3 tornillos para el

reborde inferior

(3 necesarios para la

instalación)

• La información de este manual debe

seguirse al pie de la letra.

- De no hacerlo, podría provocar un incendio o una

descarga eléctrica, causando daños a la propiedad,

lesiones personales o la muerte.

ADVERTENCIA

• NO coloque elementos pesados sobre

la puerta del horno. Nunca permita

que nadie se suba, siente, pare o

cuelgue de la puerta del horno.

- El horno puede volcarse y podrían generarse

lesiones provocadas por los alimentos o el horno.

ADVERTENCIA

• La energía eléctrica debe apagarse

mientras se efectúan las conexiones

eléctricas.

- No hacerlo puede provocar lesiones personales

graves, la muerte o una descarga eléctrica.

ADVERTENCIA

- 4 -

Parte 2 REQUISITOS DE INSTALACIÓN

DIBUJOS DE INSTALACIÓN (PARA HORNO SIMPLE EMPOTRADO DE 30”)

El primer paso de su instalación debe ser medir las dimensiones actuales de su abertura y compararlas con las dimensiones

mostradas a continuación. Puede descubrir que será necesario realizar poco o nada de trabajo en los gabinetes.

NOTA IMPORTANTE

• La plataforma base del gabinete debe poder soportar 190 lbs (86 kg). Si el gabinete no cuenta con un fondo sólido, deben

instalarse dos abrazaderas o guías niveladas con la parte inferior de la abertura para sostener el peso del horno. Asegúrese

de que la base se encuentre nivelada y que el frente del gabinete esté derecho. Si la base del gabinete no está nivelada, los

deslizadores del horno tenderán a deslizarse hacia afuera cuando se abra la puerta.

• Si marcas, imperfecciones o la abertura resultaran visibles sobre el horno instalado, puede ser necesario agregar cuñas de

madera bajo las guías y el reborde frontal hasta cubrir las marcas o la abertura.

• Si el gabinete no cuenta con un armazón frontal y los lados son menores a un grosor de 3/4” (1.9 cm), coloque cuñas

uniformemente sobre ambos lados para establecer al ancho de la abertura.

• La caja de conexiones debe estar alineada con la pared trasera del gabinete como puede verse abajo.

• Deje un espacio de por lo menos 23” para la profundidad de la puerta cuando se abre.

• Los armarios de cocina que estén en contacto con el horno deben resistir temperaturas de hasta 194 °F (90 °C), y los frentes

de las unidades cercanas hasta un mínimo de 158 °F (70 °C).

Dimensiones del producto

27 3/8”

(69.5 cm)

29 5/16”

(74.5 cm)

29 3/4”

(75.5 cm)

23 3/8”

(59.3 cm)

28 7/8”

(73.3 cm)

Dimensiones de la abertura

Ubicación de

la caja de

conexiones

23 1/2”

30”

23”

5”

28 1/2” Mín.

28 5/8” Máx.

23 1/2”

28 15/16” Mín.

29” Máx.

Ubicación

mínima de la

abertura desde el

piso 31”

Deje un mínimo

de 1” para la

superposición

del horno.

Deje un mínimo

de 1” para la

superposición

del horno.

Ancho del gabinete 30” (762 mm)

Ubicación mínima

recomendada de la

abertura desde

el piso 31” (787.4 mm)

Profundidad de la

abertura 23 1/2” Mín. (596.9 mm)

Ancho de la abertura 28 1/2” Mín. (723.9 mm)

28 5/8” Máx. (727 mm)

Altura de la abertura 28 15/16” Mín. (735 mm)

29” Máx. (736.6 mm)

- 5 -

ESPAÑOL

Parte 2 REQUISITOS DE INSTALACIÓN

DIBUJOS DE INSTALACIÓN (PARA HORNO DOBLE EMPOTRADO DE 30”)

El primer paso de su instalación debe ser medir las dimensiones actuales de su abertura y compararlas con las dimensiones

mostradas a continuación. Puede descubrir que será necesario realizar poco o nada de trabajo en los gabinetes.

NOTA IMPORTANTE

• La plataforma base del gabinete debe poder soportar 325 lbs (147 kg). Si el gabinete no cuenta con un fondo sólido, deben