Black Horse Model BH143 Manual de usuario
- Categoría
- Juguetes
- Tipo
- Manual de usuario
Este manual también es adecuado para
Instruction Manual book
Made in Vietnam.
SPECIFICATION
1 Wingspan : 1,750mm 68.90 in.
1 Length : 1,280 mm 50.39 in.
1 Weight : 3.2 - 3.5 kg 7.04 -7.7 lbs.
Parts listing required (not included):
1 Radio : 06 channels.
1 Servo : 07-09 size (29x13x30)mm.
1 Engine : 25 -2 stroke (02PCS).
1 Electric Motor : OMA - 3820 - 1200(2pcs)
1 Battery: 3 - 4CELLS-LIPO - 11.1V-14.8V - 3,250 mAh (2 Packs).
1 Speed control : 60 A (02pcs).
1 Propeller: 10 x 5.
ITEM CODE: BH143.
HEINKEL HE 111- Item code:BH143. Instruction Manual
2
This instruction manual is designed to help you build a great flying aeroplane. Please read this
manual thoroughly before starting assembly of your HEINKEL HE 111. Use the parts listing below
to identify all parts.
WARNING.
Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is
capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & RESPONSIBILITY.
If you are inexperienced with basic R/C flight we strongly recommend you contact your R/C supplier
and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training
procedures designed to help the new pilot on his way to successful R/C flight. They will also be able
to advise on any insurance and safety regulations that may apply.
TOOLS & SUPPLIES NEEDED.
1 Thick cyanoacrylate glue.
1 30 minute epoxy.
1 5 minute epoxy.
1 Hand or electric drill.
1 Assorted drill bits.
1 Modelling knife.
1 Straight edge ruler.
1 2mm ball driver.
1 Phillips head screwdriver.
1 220 grit sandpaper.
1 90° square or builder’s triangle.
1 Wire cutters.
1 Masking tape & T-pins.
1 Thread-lock.
1 Paper towels.
Some more parts.
HARDWARE PACK
COWLING.
Landing gear.....
To avoid scratching your new airplane, do not
unwrap the pieces until they are needed for
assembly. Cover your workbench with an old
towel or brown paper, both to protect the air-
craft and to protect the table. Keep a couple of
jars or bowls handy to hold the small parts af-
ter you open the bag.
Please trial fit all the parts. Make sure you have
the correct parts and that they fit and are
aligned properly before gluing! This will assure
proper assembly.
HEINKEL HE 111 ARF is hand
made from natural materials, every plane is
unique and minor adjustments may have to
be made. However, you should find the fit su-
perior and assembly simple.
The painted and plastic parts used in this kit
are fuel proof. However, they are not tolerant
of many harsh chemicals including the follow-
ing: paint thinner, C/A glue accelerator, C/A glue
debonder and acetone. Do not let these chemi-
cals come in contact with the colors on the
covering and the plastic parts.
PARTS LISTING.
FUSELAGE ASSEMBLY
1 (1) Fuselage.
WING ASSEMBLY
1 (1) Right wing half with pre-installed
aileron.
1 (1) Left wing half with pre-installed
aileron.
Tail section assembly
1 (1) Vertical stabilizer with pre-
installed rudder.
1 (1) Horizontal stabilizer with pre-
installed elevator halves.
SUGGESTION.
NOTE.
3
HEINKEL HE 111- Item code:BH143. Instruction Manual
Caution: this model is not a toy!
If you are a beginner to this type of powered model, please ask an experienced model flyer for help
and support. If you attempt to operate the model without knowing what you are doing you could
easily injure yourself or somebody else. Please keep your safety and well-being in mind at all
times.
Important: before you start construction
Even if you have already built a large number of RC models please read right through these
instructions and check all the kit components against the parts list. We have taken great trouble to
keep construction as simple as possible, without making any compromises in the area of safety.
Note regarding the film covering
Minor creases or bubbles may develop in the film covering due to major fluctuations in weather
conditions (temperature, humidity etc.); in rare cases you may even find a slight warp in a
component. These minor faults are in the nature of film-covered built-up wooden structures, and
can easily be corrected using a heat gun, as commonly used for modelling.
Creases: Blow warm air over the area and rub down with a soft cloth.
Wing warp: Hold the panel twisted gently in the opposite direction to the warp, and apply
warm air to remove the creases from the covering.
Caution! do not heat the film more than is absolutely necessary. If the air or the iron is too hot, the
film may melt and holes may be formed.
This model is highly pre-fabricated and can be built in a very short time. However, the work which
you have to carry out is important and must be done carefully. The model will only be strong and fly
well if you complete your tasks competently - so please work slowly and accurately.
When self-tapping screws have to be screwed into wood, apply a little white glue to prevent
them shaking loose: just squirt white glue into the hole and fit the screw.
+ This is not a toy
+ Be sure that no other flyers are using your
radio frequency.
+ Do not smoke near fuel
+ Store fuel in a cool, dry place, away from
children and pets.
+ Wear safety glasses.
+The glow plug clip must be securely attached
to the glow plug.
SAFETY PRECAUTION.
+ Do not flip the propeller with your fingers.
+ Keep loose clothing and wires away from
the propeller.
+ Do not start the engine if people are near.
Do not stand in line with the side of the propel-
ler.
+ Make engine adjustments from behind the
propeller only. Do not reach around the spin-
ning propeller
REPLACEMENT LARGE PARTS
B. Wing panel(B1,B2).
A. Cowling (A1,A2,A3,A4).
C. Fuselage.
B2.
B1.
A.
A.
C.
D. Fuselage top hatch.
E. Horizontal stabilizer.(E1,E2)
D.
E2.
E1.
F.
G1.
G2.
H.
H1.
H2.
F. Rudder.
G1. Aluminium tube wing.
H.Canopy .
K.
K.Pilot
A1.
A2.
A3.
A4.
G2. Aluminium tube
horizontal stabilizer
HEINKEL HE 111- Item code:BH143. Instruction Manual
4
REPLACEMENT SMALL PARTS
Cut the covering
away from the slot.
Bottom side.
Flap
Aileron
2. Wheels
1. Retract main gear (1a,1b)
3. Fuel tanks.
4.Tail gear.
7.Spinners.
5.Engine mount ply of wood .
6. Plastic - engine mount.
8.Plastic parts for Fuel tank.
1 1) Install the rubber grommets and brass
eyelets onto the aileron servos.
1.INSTALLING THE AILERON SERVOS.
Top side.
I. AILERON.
9.Plastic Canopy bottom Fuselage.
10.Canopy top Fuselage.
5
HEINKEL HE 111- Item code:BH143. Instruction Manual
Temporary pin to
keep hinge centered.
Assemble then apply drops of thin
C/A to center of hinge,on both sides.
Aileron
1 2. Using a modeling knife, remove the cov-
ering servo tray.
1 3) Using the thread as a guide and using
masking tape, tape the servo lead to the end
of the thread: carefully pull the thread out.
When you have pulled the servo lead out, re-
move the masking tape and the servo lead
from the thread.
1 4) Drill 1,6mm pilot holes through the block
of wood for each of the four mounting screws
provided with the servo.
Secure
Electric wire
Bottom side.
thread
Electric wire
HEINKEL HE 111- Item code:BH143. Instruction Manual
6
Repeat the procedure for the other
wing half.
o 5. Instal servo tray with aileron servo into
the wing as same as picture below.
2x10mm.
Secure
Aileron control horn
INSTALLING THE AILERON CONTROL HORN.
3.INSTALLING THE AILERON
LINKAGES.
1 1. Working with the aileron linkage for
now, thread one clevis onto one of the
threaded wires.
1 2. Attach the clevis to the outer hole in the
control horn. Install a silicone tube on the
clevis.
Attach the clevis to the outer hole in the con-
trol horn.
100mm
A+B
Epoxy glue
Aileron
control horn
Snap keeper.
bend
7
HEINKEL HE 111- Item code:BH143. Instruction Manual
Cut.
1 3. Plug the aileron servo into the receiver
and center the servo. Install the servo arm onto
the servo. The servo arm should be perpen-
dicular to the servo and point toward the mid-
dle of the wing.
1 4. Locate one nylon servo arm, and using
wire cutters,remove all but one of the arms.
Using a 2mm drill bit, enlarge the third hole
out from the center of the arm to accommo-
date the aileron pushrod wire.
1 5. Using pliers, carefully make a 90 degree
bend down at the mark made. Cut off the ex-
cess wire, leaving about 4mm beyond the
bend.
1 6. Insert the 90 degree bend down through
the hole in the servo arm. Install one nylon
snap keeper over the wire to secure it to the
arm. Install the servo arm retaining screw and
remove the masking tape from the aileron.
Repeat the procedure for the other wing
half.
Bottom side.
II. FLAP.
1.INSTALLING THE FLAP SERVOS.
Servos tray
HEINKEL HE 111- Item code:BH143. Instruction Manual
8
2x10mm.
Electric wire
Flap control horn
2.INSTALLING THE FLAP CONTROL HORN.
A+B Epoxy
PLUS glue
Secure.
Flap
control
Installing the flap linkages as pictures
below.
3. INSTALLING THE FLAP
LINKAGES.
3.INSTALLING THE FLAP
LINKAGES.
Bend.
100mm
Snap keeper.
9
HEINKEL HE 111- Item code:BH143. Instruction Manual
Repeat the procedure for the other wing
half.
OPTION 1. ELECTRIC MOTOR.
3x15mm.
THERE ARE TWO OPTIONS:
1. ELECTRIC MOTOR
2. ENGINE MOUNT.
INSTALLING THE ENGINE MOUNT.
Top side
bottom side
Cut.
Flap.
HEINKEL HE 111- Item code:BH143. Instruction Manual
10
Secure.
INSTALLING RETRACTABLE LANDING
GEAR
3x15mm
Secure.
Drill a hole 3.8mm
diameter.
3x15mm
11
HEINKEL HE 111- Item code:BH143. Instruction Manual
3x15mm
Secure.
HEINKEL HE 111- Item code:BH143. Instruction Manual
12
Install the engine cowling as same as
picture below.
Repeat the procedure for the other wing
half.
INSTALLING RETRACT SERVOS.
Retract
servos
Retract
servos
Secure
Cut.
ENGINE COWLING INTALLATION.
Cowling
Bottom nacelle
13
HEINKEL HE 111- Item code:BH143. Instruction Manual
INSTALLING THE BOTTOM NACELLE
3x12mm
3x12mm
Drill a hole2.5mm
diameter
Secure.
Top side.
Bottom side.
Drill a hole
2,5mm diameter
HEINKEL HE 111- Item code:BH143. Instruction Manual
14
Secure.
Secure.
Bottom left side
15
HEINKEL HE 111- Item code:BH143. Instruction Manual
Repeat procedure for the other wing panel.
3 x 12mm
INSTALLING THE SPINNER.
Secure
Left
bottom side
Left
bottom side
HEINKEL HE 111- Item code:BH143. Instruction Manual
16
Repeat the procedure for the other
wing half.
2. OPTION 2: ENGINE MOUNT.
4x12mm
secure
Drilla hole
3.8mm diameter.
Left Bottom side
3x20mm
3x25mm
17
HEINKEL HE 111- Item code:BH143. Instruction Manual
Secure.
950 mm
Mark point
1 2. Using a modeling knife, cut one length of
silicon fuel line (the length of silicon fuel line is
calculated by how the weighted clunk should
rest about 8mm away from the rear of the tank
and move freely inside the tank). Connect one
end of the line to the weighted clunk and the
other end to the nylon pick up tube in the stop-
per.
1 3. Carefully bend the second nylon tube up
at a 45 degree angle (using a cigarette lighter).
This tube will be the vent tube to the muffler.
1 4. Carefully bend the third nylon tube down
at a 45 degree angle (using a cigarette lighter).
This tube will be vent tube to the fueling valve.
INSTALLING THE STOPPER ASSEMBLY
FUEL TANK.
1 1. The stopper has been pre-assembled at
the factory.
Drill a hole
2.5mm diameter
Secure.
HEINKEL HE 111- Item code:BH143. Instruction Manual
18
When the stopper assembly is installed
in the tank, the top of the vent tube should
rest just below the top surface of the tank.
It should not touch the top of the tank.
Blow through one of the lines to ensure
the fuel lines have not become kinked inside
the fuel tank compartment. Air should flow
through easily.
1 8. Feed three lines through the fuel tank
compartment and through the pre-drilled hole
in the firewall. Pull the lines out from behind
the engine, while guiding the fuel tank into
place. Push the fuel tank as far forward as
possible, the front of the tank should just about
touch the back of the firewall.
1 7. Using a modeling knife, cut 3 lengths of
fuel line 150mm long. Connect 2 lines to the 2
vent tubes and 1 line to the fuel pickup tube in
the stopper.
1 5. Test fit the stopper assembly into the
tank. It may be necessary to remove some of
the flashing around the tank opening using
a modeling knife. If flashing is present, make
sure none of it falls into the tank.
1 6. When satisfied with the alignment of the
stopper assembly tighten the 3mm x 20mm
machine screw until the rubber stopper ex-
pands and seals the tank opening. Do not over
tighten the assembly as this could cause the
tank to split.
Vent tube
Fuel fill tube
Fuel pick - up tube
1 9. To secure the fuel tank in place, apply a
bead of silicon sealer to the forward area of
the tank, where it exits the fuselage behind the
engine mounting box and to the rear of the tank
at the forward bulkhead.
Left bottom side
Remove
covering
Fuel tank
19
HEINKEL HE 111- Item code:BH143. Instruction Manual
3x12mm.
Secure.
1 1. Install one adjustable metal connector
through the third hole out from the center of
one servo arm, enlarge the hole in the servo
arm using a 2mm drill bit to accommodate the
servo connector. Remove the excess mate-
rial from the arm.
After installing the adjustable metal con-
nector apply a small drop of thin C/A to
the bottom nut. This will prevent the con-
nector from loosening during flight.
Throttle servo.
Throttle servo.
INSTALLING THE THROTTLE PUSHROD
Throttle pushrod
Fuel tank
HEINKEL HE 111- Item code:BH143. Instruction Manual
20
Secure.
Secure.
ELEVATOR INSTALLATION.
1 1. Install the rubber grommets and brass
collets into the elevator servo. Test fit the servo
into the servo tray.
1 2. Mount the servo to the tray using the
mounting screws provided with your radio sys-
tem.
SERVO INSTALLATION.
Throttle pushrod
Elevator
servos
1 Horizontal stabilizer installation .
See picture below.
Cut the covering
away from the slot.
Temporary pin to
keep hinge centered.
HORIZONTAL STABILIZER
INSTALLATION.
Elevator
servos
21
HEINKEL HE 111- Item code:BH143. Instruction Manual
Assemble then apply drops of thin
C/A to center of hinge,on both sides.
C/A glue.
Epoxy glue.
Aluminium 9mm tube
220mm
HEINKEL HE 111- Item code:BH143. Instruction Manual
22
Control horn of elevator.
Elevator pushrod install as same as the way
of aileron pushrod.
ELEVATOR PUSHROD INSTALLATION.
M2
M2 lock nut.
Elevator
control horn
Elevator
pushrod.
Bottom side
C/A glue.
Elevator control horn install as same as the
way of aileron control horn. Please see pic-
tures below.
ELEVATOR CONTROL HORN INSTALLA-
TION.
A+B Epoxy
PLUS glue.
23
HEINKEL HE 111- Item code:BH143. Instruction Manual
Bottom side
Elevator
pushrod.
Elevator
pushrod.
Bend.
Cut.
MOUNTING THE TAIL WHEEL
BRACKET.
VERTICAL INSTALLATION.
Elevator
pushrod.
3x12mm
HEINKEL HE 111- Item code:BH143. Instruction Manual
24
1 3. Secure the tail wheel bracket in place
using three 3mm x 12mm wood screws. Be
careful not to overtighten the screws.
Drill a hole
2mm
3x 12mm
Secure.
Bottom side.
Rudder
servo
Rudder servo install as same as method of
elevator servo. See picture below:
RUDDER SERVO INSTALLATION.
Rudder
servo
25
HEINKEL HE 111- Item code:BH143. Instruction Manual
See picture below:
RUDDER INSTALLATION.
Cut the covering
away from the slot.
Temporary pin to
keep hinge centered.
Assemble then apply drops of thin
C/A to center of hinge,on both sides.
A+B Epoxy glue.
HEINKEL HE 111- Item code:BH143. Instruction Manual
26
Rudder control horn install as same as the
way of aileron control horn. Please see pic-
tures below.
Control horn of Rudder.
Control
horn.
RUDDER PUSHROD INSTALLATION.
Rudder pushrod install as same as the way
of aileron pushrod.
Rudder Pushrod.
Rudder Pushrod.
Top side.
RUDDER CONTROL HORN INSTALLA-
TION.
A+B Epoxy
PLUS glue.
Right bottom side.
27
HEINKEL HE 111- Item code:BH143. Instruction Manual
Plastic parts of elevator pushrod and
rudder pushrod.
Rudder
pushrod
Cut.
Bottom side.
HEINKEL HE 111- Item code:BH143. Instruction Manual
28
Bottom side.
Bottom side.
C/A glue.
Top side.
C/A glue.
INSTALLING COCKPIT FUSELAGE .
See picture below:
C/A Epoxy
glue.
Pillot
29
HEINKEL HE 111- Item code:BH143. Instruction Manual
C/A glue.
Installing the canopy
C/A glue.
C/A glue.
C/A glue.
HEINKEL HE 111- Item code:BH143. Instruction Manual
30
C/A glue.
Left Top side
Right Top side
Bottom side
1 1. Plug the servo leads and the switch
lead into the receiver. You may want to plug
an aileron extension into the receiver to make
plugging in the aileron servo lead easier
when you are installing the wing . Plug the
battery pack lead into the switch.
1 2. Wrap the receiver and battery pack in
the protective foam to protect them from vi-
bration. Use a rubber band or masking tape to
hold the foam in place.
Do not permanently secure the receiver and
battery until after balancing the model.
1 3. Position the battery pack and receiver
behind the fuel tank. Use two tie wraps to hold
the battery and receiver securely in place as
pictures below
INSTALLING THE RECEIVER AND BATTERY.
Tie wrap.
C/A glue.
Bottom side.
31
HEINKEL HE 111- Item code:BH143. Instruction Manual
Battery.
Receiver.
WING ATTACHMENT.
1.Locate the aluminium wing dihedral brace.
*** Test fit the aluminium tube dihedral brace
into each wing haft. The brace should slide in
easily. If not, use 220 grit sand around the
edges and ends of the brace until it fits prop-
erly.
Aluminium tube 12mm
511mm.
1 2. Attach the aluminium tube into the
fuselage.
Right side.
Left side.
HEINKEL HE 111- Item code:BH143. Instruction Manual
32
Secure.
C/A glue.
C/A glue.
33
HEINKEL HE 111- Item code:BH143. Instruction Manual
1 3. Turn the airplane upside down. Place
your fingers on the masking tape and care-
fully lift the plane .
1 1) It is critical that your airplane be bal-
anced correctly. Improper balance will cause
your plane to lose control and crash.
THE CENTER OF GRAVITY IS LOCATED
130MM BACK FROM THE LEADING EDGE
OF THE WING.
1 2) Mount the wing to the fuselage. Using a
couple of pieces of masking tape, place them
on the top side of the wing 130 mm back from
the leading edge, at the fuselage sides.
Accurately mark the balance point on the top
of the wing on both sides of the fuselage. The
balance point is located 130mm back from the
leading edge. This is the balance point at which
your model should balance for your first flights.
Later, you may wish to experiment by shifting
the balance up to 10mm forward or back to
change the flying characteristics. Moving the
balance forward may improve the smooth-
ness and arrow- like tracking, but it may then
require more speed for take off and make it
more difficult to slow down for landing. Moving
the balance aft makes the model more agile
with a lighter and snappier ”feel”. In any case,
please start at the location we recommend .
With the wing attached to the fuselage, all
parts of the model installed ( ready to fly), and
empty fuel tanks, hold the model at the
marked balance point with the stabilizer level.
Lift the model. If the tail drops when you
lift, the model is “tail heavy” and you must add
weigh* to the nose. If the nose drops, it is “nose
heavy” and you must add weight* to the tail to
balance.
*If possible, first attempt to balance the model
by changing the position of the receiver bat-
tery and receiver. If you are unable to obtain
good balance by doing so, then it will be nec-
essary to add weight to the nose or tail to
achieve the proper balance point.
BALANCING.
4 1) We highly recommend setting up a
plane using the control throws listed.
4 2) The control throws should be meas-
ured at the widest point of each control sur-
face.
4 3) Check to be sure the control surfaces
move in the correct directions.
Ailerons : 10mm up 10mm down.
Flap: 20mm down.
Elevator : 12mm up 12mm down.
Rudder : 15mm right 15mm left.
CONTROL THROWS.
10mm
10mm
12mm
12mm
15mm
15mm
20mm
HEINKEL HE 111- Item code:BH143. Instruction Manual
34
4 1) Completely charge your transmitter and
receiver batteries before your first day of fly-
ing.
4 2) Check every bolt and every glue joint in
your plane to ensure that everything is tight
and well bonded.
4 3) Double check the balance of the
airplane.
4 4) Check the control surface.
4 5) Check the receiver antenna . It should
be fully extended and not coiled up inside the
fuselage.
4 6) Properly balance the propeller.
PRE-FLIGHT CHECK.
We wish you many safe and enjoyable
flights with your HEINKEL HE 111.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
Black Horse Model BH143 Manual de usuario
- Categoría
- Juguetes
- Tipo
- Manual de usuario
- Este manual también es adecuado para
en otros idiomas
- English: Black Horse Model BH143 User manual