Mora MRF266N6CSE El manual del propietario

Marca: Mora

Modelo: MRF266N6CSE

Categoría: Neveras

Tipo: El manual del propietario

Refrigerator Use & Care Guide

Model: MRF266N6CSE

MRF211N6CSE

For questions about features, operation/performance, parts or service, call:

1-877-465-3566

English

Table of Contents

Brief introduction

Important safety instructions

Installing your new appliance

Description of the appliance

Display controls

Using your appliance

Cleaning and care

Helpful hints and tips

Troubleshooting

Disposal of the appliance

..................................................................................................................... 3

................................................................................................. 4

................................................................................................ 6

.............................................................................................. 13

...................................................................................................................... 14

............................................................................................................ 16

............................................................................................................... 19

............................................................................................................. 21

..................................................................................................................... 22

.................................................................................................... 24

Thank you for choosing MORA. We are sure you will find your new refrigerator a

pleasure to use. However, before you use the appliance, we recommend that you

read through these instructions carefully, which provides details about installing and

using the product. Please keep a copy for future reference.

Brief Introduction

Please ensure that everyone using this

appliance is familiar with its operation

and safety features. It is important that

you install the appliance correctly and

pay careful attention to the safety

instructions.

We recommend that you keep this user’s

manual with the appliance for future

reference.

This appliance is intended to be used

in households and similar applications

such as:

Thank you for your choosing Hisense. We

are sure you will find your new refrigerator

a pleasure to use. Before you use the

appliance, we recommend that you

carefully read through these instructions ,

which provide details about installing and

using the product.

This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or

lack of experience and knowledge, unless

they have supervision or been given

instruction concerning use of the appliance.

Children should be supervised to ensure

that they do not play with the appliance.

Do not store explosive substances such as

aerosol cans with a flammable propellant

in this appliance.

Connect to potable water supply only.

Do not use mechanical devices or other

means to accelerate the defrosting

process, other than those

recommended by the manufacturer.

Do not damage the refrigerant circuit.

Do not use electrical appliances inside

the food storage compartments of the

appliance, unless they are of the type

recommended by the manufacturer.

When disposing of the appliance do so

only at an authorized waste disposal

center. Do not expose to flame.

If the power cord is damaged, it must be

replaced by the manufacturer, its

service agent or similarly qualified

persons in order to avoid a hazard.

WARNING

Kitchen areas in shops, offices and other

working environments.

Hotels, motels and other residential

environments.

Bed and breakfast environments.

Catering and similar non-commericial

applications.

General safety and daily use

It is important to use your appliance

safely. We recommend that you follow the

guidelines below.

Store any food in accordance with the

storage instructions from the manufacturer.

Important Safety Instructions

Safety for children and

other persons

Don't try to repair the appliance yourself.

It is dangerous to alter the

specifications or modify this product in

any way. Any damage to the power

cord may cause a short circuit, fire or

electric shock.

Don’t place too much food directly

against the air outlet on the rear wall

of both the refrigerator and freezer

compartment, as it may affect

important air circulation.

Don’t place hot items near the plastic

components of this appliance.

Frozen food must not be refrozen once it

has been thawed out.

Don’t store bottled or canned drinks

(especially carbonated drinks) in the

freezer compartment. Bottles and cans

may explode.

Use caution consuming popsicles or ice

cubes straight from the freezer as this can

cause freezer burn to the mouth and lips.

Keep all packaging away from children

to avoid risk of suffocation.

Protect children from being scalded by

touching the compressor at the rear

bottom of appliance

Don’t place items on top of the

appliance as this could cause injury

should they fall off.

Never allow children to play with the

appliance by hanging or standing over

or on the doors, racks, shelves and

drawers etc.

Electrical Safety

To avoid the risks that are always present

when using an electric appliance, we

recommend that you pay attention to

the instructions about electricity belo

Unpack and check through the

appliance. Should any damage be

evident, don’t plug in the appliance but

contact the shop immediately from

which you purchased it. Keep all

packing materials in this case.

We recommend that you wait for 4 hours

before connecting the appliance to

allow the refrigerant to flow back into

the compressor.

The appliance must be applied with

single phase alternating current of

110~115V/60Hz. If the voltage fluctuates

exceeding the upper limit, A.C.

automatic voltage regulator of more

than 350W should be applied to the

refrigerator for safety use.

The power plug must be accessible

when the appliance is installed.

This appliance must be grounded.

This appliance is fitted with a plug,

in accordance with local standard.

The plug should be suitable for use in all

houses fitted with sockets in accordance

with current specifications.

Electrical Safety

To avoid the risks that are always present

when using an electric appliance, we

recommend that you pay attention to

the instructions about electricity below.

If the fitted plug is not suitable for your

socket outlets, it should be cut off and

carefully disposed of. To avoid a

possible shock hazard, do not insert the

discarded plug into a socket. If in doubt

contact a qualified, registered

electrician.

Do not use extension cords or multiple

sockets which could cause overloading

of wiring circuits and could cause a fire.

Always plug your appliance into its own

individual electrical socket which has

a voltage rating that matched the

rating plate.

Make sure that the plug is not squashed

or damaged. Otherwise, it may cause

short circuit, electric shock or overheat

and even cause a fire.

Do not insert the power plug if the

socket is loose, there is a risk of electric

shock or fire.

Switch off the appliance and

disconnect it from the main power

before you clean or move it.

Never unplug the appliance by pulling

on the electrical cord. Always grip the

plug firmly and pull straight out from the

socket to prevent damaging the power

cord.

Do not operate the appliance without

the cover of interior lighting.

Any electrical component must be

replaced or repaired by a qualified

electrician or authorized service

engineer. Only genuine replacement

parts should be used.

Do not use electrical appliances such

as ice cream makers inside the food

storage compartments of the

appliance unless they are approved

by the manufacturer.

To avoid eye injury, do not look directly

into the LED light located in the refrigerator

compartment. If it is not functioning

correctly, consult a qualified, registered

electrician or replace it in accordance

with the “Cleaning and Care” chapter.

The refrigerant isobutane (R600a) is

contained within the refrigerant circuit of

the appliance. During transportation and

installation of the appliance, ensure that

none of the components of the refrigerant

circuit become damaged.

The refrigerant (R600a) is flammable.

Don't store products which contain

flammable propellants (e.g. spray cans)

or explosive substances in the appliances.

Avoid open flames (candles, lamps etc. )

and other sources of ignition.

Thoroughly ventilate the room in which

the appliance is situated.

Refrigerant

Caution: Risk of Fire

Should the refrigerant circuit

be damaged:

Installing Your New Appliance

WARNING

Before using the appliance for the first time,

you should be informed of the following tips.

For proper installation, this refrigerator

must be placed on a level surface of

hard material that is the same height

as the rest of the flooring. This surface

should be strong enough to support a

fully loaded refrigerator.

The rollers, which are not casters,

should be only used for forward or

backward movement. Moving the

refrigerator sideways may damage

your floor and the rollers.

Suggestion:

It is advisable for there to be at least

2"(50mm) of clearance from the back of

the fridge to the wall, at least 1/2"(12mm)

of clearance from its top, at least 1/2"

(12mm ) from its side to the wall and

a clear space in front to allow the doors

to open 125°. As shown in the following

diagrams.

In order to improve efficiency of the

cooling system and save energy, it is

necessary to maintain good ventilation

around the appliance for the dissipation

of heat. For this reason, sufficient clear

space should be available around the

refrigerator.

Ventilation of appliance

This appliance performs well within the

climate class from N to T shown in the table

below. It may not work properly if left at a

temperature above or below the

indicated range for a long period.

Stand your appliance in a dry place to

avoid high moisture.

Keep the appliance out of direct sunlight,

rain or frost. Stand the appliance away

from heat sources such as stoves, fires or

heaters.

Climate class

+50°F to + 90°F

+61°F to + 90°F

+61°F to + 100°F

+61°F to + 109°F

Ambient temperature

Note:

1/2 "

2 "

1/2"

1/2 "

70"

For sufficient leveling and air circulating

in the lower rear section of the

appliance, the bottom feet may need

to be adjusted. You can adjust them

manually by hand or by using a suitable

tool.

To allow the doors to self-close, tilt the

top backwards by 0.4" - 0.6"(10-15mm).

Leveling of appliance

Adjustable

bottom feet

Front roller Rear roller

0.4"~0.6"(10-15mm)

Adjustable

bottom feet

Before you use the appliance, you have to

install the handles provided in the fridge

chamber.

The longer one is fridge door handle, the

shorter one is freezer door handle.

Please follow procedures below to install

and reverse the handle.

Installing the handles

Take out the screw hole covers on the

doors, install the handle supports(C).

Place the handle (A) on the door by

supports (C), then fasten the screws (B)

with 3mm Allen wrench (provided in

plastic bag).

Adjusting Door Height and Gap

In case your home access door is too

narrow for the refrigerator to pass

through, remove the refrigerator doors

and drawers. If you do not need to

remove the appliance doors, proceed

to ‘Installing Water Lines’ on page 10.

If you need to remove the doors,

continue below.

Door Removal

Tools you will need(Not provided)

Allen Wrench (5/32",4mm)

Philips Screwdriver

Wrench (5/16",8mm)

With the door closed, remove the 3 screws

holding the top cover (A) with Philips (+)

screwdriver, and then remove the top

cover with the entireharness attached.

Remove the screws (B) fixed on the hinges

with a wrench (5/16",8mm) and 1 ground

screw (C) attached to the hinge with

Philips (+) screwdriver. Remove the upper

left and right door hinges (D).

The height of a door can be adjusted

using the provided Snap Rings.

Tools you will need:

Snap Ring (4pcs) Wrench(Not provided)

To adjust the Height of Door

1. Check the height difference between

the doors and then lift and hold the

lowest door to be even with the other.

2. Insert a suitably sized Snap Ring between

the Door and the Hinge as shown.

IMPORTANT !

1. Insert only one Snap Ring. If you insert

two or more Snap Rings, they may slip

out or cause a rubbing noise.

2. Do not raise the door too much. The

door may contact and damage the

top cover.

3. Save rermaining Snap Rings for

possible future use.

4. Remove the 4 hex head bolts hinges (E)

with an Allen wrench (5/32",4mm).

Remove the lower left and right door

hinges (F).

Pull out the freezer door and the upper

freezer drawer (G) to the final position.

Take out the ice storage box (H) by

lifting it up in the direction of the arrow.

Take out the upper freezer drawer (G)

by lifting it up from the rail system.

Disassembling the freezer door

Use both hands to open the door more

than 90°. Lift it up and take it off.

Remove the lower freezer drawer (C)

by lifting it up.

Remove the 4 screws attached to the

supporting frame (D).

4.You need to purchase several item to

compalet this connection.You may find

these items sold as a kit at local hardware

store.

Re-assembling the freezer door

To reattach the drawer after you moved

the appliance to its final location,

assemble the parts in reverse order.

A water dispenser with a filter is one of the

helpful features on your new appliance.

To help promote better health, the water

filter removes unwanted particles from your

water. However, it does not sterilize or

destroy microorganisms. You may need

to purchase a water purifying system to

do that.

In order for the ice maker to operate

properly, a water line is required.

-the maximum inlet water pressure is 700kPa;

-the minimum inlet water pressure is 207kPa.

Installing the water lines

Pull out the freezer door and lift it up

in the direction of the arrow. 1. Power drill and 1/4’’ drill bit.

2. 1/2’’ or adjustable wrench.

3. Flatblade and Philips head screwdrivers.

1 ferrule

(sleeve)

What you need to have before you start

Saddle-type

Shut offvalve

(1/4” outlet)

one 1/4”

compression

1/4” extension

tubing

1 Coupler 2 Clips

WARNING!

The water connection must be made

by a qualified plumber. Operation

outside the water pressure range

may cause malfunction, severe and

damaging water leaks.

Under normal conditions, a200cc

(5.75 oz.) cup can be filled in about

10 seconds.

If the refrigerator is installed in an area

with low water pressure (below 30psi),

you can install a booster pump to

compensate for the low pressure.

First, shut off the main water supply.

Connecting to the water supply line

Cold water line

Pipe clamp

Shut off Valve

Using a power drill and a 1/4’’ drill bit

drill into the cold-water line and

connect the saddle-type shutoff valve.

3. Connect 1/4’’ extension tubing to shutoff

valve outlet.

Flush the tubing. Turn the main water

supply on and flush out the tubing until

the water is clear. Then, shut the water

off at the water valve after about a quart

of water has flushed through the tubing.

Outllet Valve

Packing Nut

Saddle-Type

Shutoff Valve Compression Nut

1/4” Extension

tubing

Ferrule(sleeve)

Connect the extension tubing line with

the line on the back of the fridge via

the coupler. Fully insert the extension

tubing into the coupler, and then insert

the clip onto the coupler to lockup the

tubing. Do the same with the other

end. After both clips are inserted,

check the line to make sure it is held

firmly by the clip.

Note:

Ensure that the water line does not get

pinched or bent when installing.

This can result in improper water flow

through the line and will affect the

functionality of the fridge.

Clip

Water line Water line

Coupler

Note:

Use only the new tubing supplied with

the refrigerator. Old tubing should not

be used.

After connected to the water supply line,

please open the water valve to flush the

filter for 5 minutes before use. The initial

dark discoloration of water is normal.

When you connect the water line to the

appliance and press the lever of the

dispenser for the first time, it is normal that

there will be a sound of exhaust coming

out from the appliance.

1.The water line must be

connected to the cold water

pipe. If it is connected to the hot

water pipe, it may cause the

purifier to malfunction.

2.Avoid contamination of pipes

during installation.

3.Connect to potable water

supply only.

WARNING!

CAUTION!

Check to see if leaks occur at the

water line connections

6. Turn the water on and check

for leakage.

Thread a 1/4 " compression nut and

ferrule (sleeve) onto the free end and

of 1/4" water line.

Insert the free end and of the 1/4" water

line into the brass fitting attached to the

water inlet on the back of the refrigerator.

c1/4" Water Line

1/4" Compression Nut

Ferrule(Sleeve)

Brass Fitting

Slide the 1/4" compression nut over the

ferrule (sleeve) and screw the 1/4"

compression nut onto the brass ftting.

7. Comfirm 1/4" water line is secure by

gently pulling on it.

8. Turn on water supply and check for leaks,

and correct any leaks.

Note:

The water line must be

connected to the cold water

pipe. If it is connected to the hot

water pipe, it may cause the

purifier to malfunction.

Avoid contamination of pipes

during installation.

Connect to potable water

supply only.

WARNING!

Water Inlet

Connect Water Line to Refrigerator

IMPROTANT:

If you turn the refrigerator

on before the water is connected, turn

off the ice maker.

Unplug refrigerator or disconnect

power.

Close shut off value.

a b c Ferrule (Sleeve) -1 pcs

1/4" Compression Nut - 1 pcs

1/4" Water Line - 1 pcs

1.You may need to purchase below

items to complete this connection.

And you may find these items sold

as a kit at a local hardware store.

After connected to the water supply line,

please open the water valve to flush the

filter for 5 minutes before use. The initial

dark discoloration of water is normal.

When you connect the water line to the

appliance and press the lever of the

dispenser for the first time, it is normal

that there will be a sound of exhaust

coming out from the appliance.

Use only the new tubing supplied with

the refrigerator. Old tubing should not

be used.

Air Channel

Glass Shelf

Adjustable bottom feet

Door Bins

Mullion

Crisper Cover

Crisper Drawer

Full-width Pantry

Ice Maker (inside)

Ice storage box (inside)

Hinge Cover

Control panel

Mullion Guide Block

Freezer Lower Drawer

Water Filter

Freezer Upper Drawer

Refrigerator LED Light

Due to unceasing modification of our products, your refrigerator may be slightly different

from this instruction manual, but its functions and using methods remain the same.

To get the best energy efficiency of this product,please place all shelves, drawers and

baskets on their original position as per the illustration above.

Note:

Water dispenser (inside)

You can touch the “Fridge” icon to

activate the mode to control the fridge

temperature. When you touch the

button continuously, the temperature

will be set in the following sequence.

Display Controls

Your product has one control panel which is installed on the top cover. Use your

appliance according to the following control guidelines.

When the appliance is powered on for

the first time, the backlighting of the

icons on the display panel start working.

If no buttons have been touched or the

doors are closed, the backlighting will

turn off after 60 seconds.

The control panel consists of two areas

about temperature, and one area

about different modes.

This button controls the ice maker. You

can touch the “Ice On/Off” button to

control the ice maker. When the “Ice

On/Off” function light is on, the ice

maker is working. If you want to lock the

ice maker, please touch the “Ice On/

Off” button again until the button light

is off.

CAUTION!

When you set a temperature, you

set an average temperature for

the whole refrigerator cabinet.

Temperatures inside each

compartment may vary from the

temperatures displayed on the

panel, depending on how much

food you store and where you place

it. High or low room temperature

may also affect the actual

temperature inside the appliance.

Ice Control

Fridge Temperature

Control

If you want to decrease the time needed

to cool products in the Fridge, please

touch this button. The Super Cool icon

“ ” will be illuminated, and the fridge

temperature setting displays at 35°F.

Super cool automatically switches off

after 3 hours, and the refrigerator

temperature setting will revert back to

the previous setting.

When Super Cool function is on, you can

touch the “Super Cool” button again to

switch it off. The fridge will not retain the

Super Cool function when powered off.

Super Cool

You can touch the “Freezer” button to

activate the mode to control the freezer

temperature. When you press the button

continuously, the temperature will be set in

the following sequence.

Freezer Temperature

Control

Fridge

Freezer

Ice

On/Off

Super

Cool

47°F - 46°F -45°F - 44°F -43°F - 42°F - 41°F

40°F

39°F -

38°F -

37°F -

36°F -

35°F -

6°F ~ 5°F ~ 4°F ~ 3°F ~ 2°F ~ 1°F ~ 0°F ~ -1°F ~ -2°F ~ -3°F ~ -4°F

-12°F ~ -11°F ~ -10°F ~ -9°F ~ -8°F ~ -7°F ~ -6°F ~ -5°F

If you want to decrease the time needed

to freeze products in the freezer, please

touch this button, the Super Freeze icon

“ ” will be illuminated, the freezer

temperature setting displays -12°F.

Super Freeze can quickly lower the

temperature and freeze your food faster

than usual. This can retain more of the

vitamins and nutrients in fresh food and

keep your food longer.

Super

Freeze

Super Freeze

The control panel will light up when the

door is open, or you touch any button.

The light will go off without touching any

buttons or if the doors have been closed

for over one minute.

When the refrigerator is powered on, all

the icons of the control panel will light up

for 3 seconds, and a buzzer sounds.

The temperature setting reverts back to

the previous setting.

The Super Freeze mode allows you to

freeze items inside with maximum speed.

We recommend that you let the

appliance operate for 6 hours first.

Super Freeze automatically switches off

after 26 hours, and the freezer

temperature setting will revert back to

the previous setting.

When the Super Freeze function is on,

you can touch the “Super Freeze” button

again to switch off. If power cutoff

happens while Super Freeze is activated,

the Super Freeze will not remain active

after power is resupplied.

Before that, please check that the new

filter is the same filter type that came with

your fridge and can be correctly used in

your refrigerator.

After you change the water filter, push and

hold the “Ice On/Off” and “Super Freeze”

buttons for 3 seconds to make the blinking

stop. When you replace the water filter,

some water may leak from the filter and

lines. Please let the water flow into a pan

and wipe up any leakage that may have

occurred.

Note:

If you want to exchange the “°F” to “°C”,

please press and hold the “Super Cool”

and “Energy Saving” buttons for 3 seconds.

In general, you should change the water

filter every 6 months to ensure the highest

possible water quality.

After the refrigerator has dispensed about

300 gallons of water, the filter icon “ ”

will blink, reminding you to replace the

water filter.

First of all, you need to purchase a new

water filer. You can purchase the new

filter from the retailer where you

purchased your refrigerator or the

Hisense after-sales service system.

Water Filter

Energy Saving

Energy

Saving

Note:

Demo mode is for store display, and it

prevents the refrigerator from generating

cool air. In Demo Mode, the refrigerator

may seem like it is working but it will not

make cool air.

The indicators on the control panel will

show double “0F”. To cancel this mode,

press and hold “Ice On/Off” and

“Energy Saving” keys at the same time

for 3 seconds until the buzzer beep three

times and the display panel will light for

3 seconds.

Demo mode (Freezer/ Fridge

Temperature Indicator moving)

You can touch this button to turn Energy

Saving mode on and off. When you turn

Energy Saving on, the Energy Saving icon

“ ” lights up. The temperature of the

fridge is automatically switched to 42°F

and the freezer to 2°F. If you turn Energy

Saving off, the icon “ ” will go off and the

temperature setting will revert back to

the previous setting.

Door Alarm

When any door is open over 2 minutes, the

door alarm will be actrivated. The buzzer

will sound 3 times every 1 minute and the

display will present “dr”. The alarm will stop

when the doors closed or stop automatically

after 10 minutes.

To save energy, please avoid keeping the

door open for long time when using the

appliance.

Changing the water filter

To drink the freshest and cleanest water

from your refrigerator, change the filter

on time.

Please follow these steps:

This section tells you how to use most of

the useful features. We recommend that

you read through them carefully before

using the appliance.

Using your Appliance

The water dispenser is located in the left

side of the fridge. Open the refrigerator

doors, and push the water dispenser

button to get water. Then move your

glass down the dispenser lever in the

suggested position and press it.

Hold the glass underneath the dispenser

for 2~3 seconds after releasing the

dispenser button as water may continue

to dispense after the button is released.

Getting Cold Water

About 1.6inch

Shut off the water supply. Then turn

the water filter (K) about a 1/4 turn,

counter-clockwise.

When having problem with releasing water

filter, please use the enclosed tool which

provide in package as above. Insert the

tool into the filter housing and rotate it

counter clock wise (to the left) 90 degrees.

Please keep for future use when changing

the water filter.

Note

2. Pull the water filter (K) from the filter

holder (L).

To change the water filter easily, shut off

the water supply valve.

Sometimes, it is hard to disassemble the

water filter because impurities in the

water cause it to stick. If you are having

difficulties, grip the water filter firmly and

pull it out.

When you pull the water filter, a little

water can leak from the opening.

This is normal. To minimize the water

leaks, keep the filter cartridge horizontal

when pulling it.

Note

To prevent overflow, empty the water

filter tray (M) and dry around the filter

case.

To insert the new water filter, follow the

directions below.

Removing any residual matter inside the

water supply line after installing the water

filter

1. After the water filter is replaced,

dispense 2.5 gallons of water (flush for

approximately 5 minutes) to remove

trapped air and contaminants from

the system.

2. Additional flushing may be required in

some households.

3. Open the refrigerator door and make

sure there are no water leaks coming

from the water filter.

Insert the new filter into the filter holder.

Push the filter, and then turn it clockwise

until it locks.

If you have trouble inserting the water

filter because of high water pressure, shut

off the water supply valve.

If you turned off the water supply, turn it

back on.

After turning on the water supply, you

should check the leaks. If leaks occur,

repeat the steps 1- 5. If leaks

persist, discontinue use and call

Hisense customer service..

Note:

Be sure to flush the dispenser thoroughly,

otherwise water may drip from the

dispenser. This means that there is still air

in the line.

Do not dispense the entire 2.5 gallon

amount continuously. Depress and

release the dispenser pad for cycles

of 30 seconds ON and 60 seconds OFF.

Check to see whether the sediment filter

in the reverse osmosis system is blocked.

Replace the filter if necessary.

Allow the storage tank on the reverse

osmosis system to refill after heavy usage.

If your refrigerator has a water filter,

it may further reduce the water pressure

when used in conjunction with a reverse

osmosis system. To resolve it, remove the

water filter.

Reverse osmosis water supply:

The pressure of the water supply coming

out of a reverse osmosis system going to

the water inlet valve of the refrigerator

needs to be between 30 and 100psi (207

and 700kPa). If a reverse osmosis water

system is connected to your cold water

supply, the water pressure to the reverse

osmosis system needs to be a minimum of

40 to 60 psi (276 to 414 kPa).If the water

pressure to the reverse osmosis system is

less than 40 to 60 psi (276 to 414 kPa):

Note:

2 Using your fridge compartment

The refrigerator compartment is suitable

for storage of vegetables and fruit. Food

inside should be sealed for storage in order

to avoid losing moisture or flavor

permeating into other foods.

CAUTION!

Never close the refrigerator door

while the shelves, crisper and/or

telescopic slides are extended

It may damage both them and

the refrigerator.

The refrigerator compartment is provided

with six door baskets, which are suitable

for the storage of canned liquid, bottled

drinks and packaged food.

To remove the door baskets, simply lift

the racks up and pull straight out.

To relocate the door baskets, slide it in

above the desired location and push

down until it stops.

Door baskets

WARNING!

Do not place too many heavy

things in the baskets. Before you

liftup the door shelf vertically,

please take the food out.

To remove the glass shelves, tilt up the front

of the shelf in the direction shown (N) and

lift it up vertically (O). Pull the shelf out.

Glass shelves

O N

To re-install the glass shelves, tilt the front of

the shelf up and guide the shelf hooks into

the slots at a desired height (P). Then lower

the front of the shelf so that the hooks can

drop into the slots (Q).

The crispers are suitable for storage of

vegetables and fruit. To take them out,

open the door to the final location first.

Then pull out the drawer and tilt up the

front of the crisper after moving slightly

in the direction of the arrow.

Vegetable and fruit crispers

The freezer compartment is provided with

an upper drawer, a lower drawer and an

ice box. To remove all of them, refer to

page 8 for disassembly instruction.

Using the freezer compartment

Press ICE On/Off to turn the ice maker

on and Off. The Ice Maker icon is “ ”

illuminated when the ice maker is

functioning.

Ice

On/Off

Following installation, allow 24 hours to

produce the first batch of ice. Discard

the first three batches of ice produced.

Allow 2 to 3 days to fill the ice storage

container.

If the ice in the ice container clumps,

break up ice using a plastic utensil and

discard. Do not use a sharp tool to break

up the ice. This can cause damage to

the ice container.

Do not store any items other than ice in

the ice storage container.

Feeler Arm Ice Storage

Container

Motor

To maintain good appearance of your

appliance, you should clean it regularly.

Spray water onto a cleaning cloth

instead of spraying directly on the

surface of the appliance. This helps

ensure an even distribution of moisture

to the surface.

Clean the doors, handles and cabinet

surfaces with a mild detergent and

then wipe dry with a soft cloth.

Exterior cleaning

For hygienic reasons the appliance

(including exterior and interior

accessories) should be cleaned at least

every two months.

Cleaning and Care

WARNING!

To avoid electrical shock, the

appliance must not be connected

to the main power supply during

cleaning. Before cleaning, switch

the appliance off and remove

the plug from the main socket.

CAUTION!

1. Don’t use sharp objects to clean

with, as they are likely to scratch

the surface.

2. Don’t use thinner, car cleaner,

bleach, oil, abrasive cleansers or

organic solvent such as benzene

for cleaning. They may damage

the surface of the appliance

and may cause fire.

You should clean the appliance interior

regularly. It will be easier to clean when

food stocks are low. Wipe the inside of

the fridge and freezer with a weak

solution of backing soda and water, and

then rinse with warm water using a

wrung-out sponge or cloth. Wipe

completely dry before replacing the

shelves and baskets. Thoroughly dry all

surfaces and removable parts before

putting them back into place.

Interior cleaning

Although this appliance automatically

defrosts, a layer of frost may occur on

the freezer compartment’s interior walls if

the freezer door is opened frequently or

kept open too long. If the frost is too

thick, choose a time when the freezer is

nearly empty and proceed as follows:

Remove existing food and accessory

baskets, unplug the appliance from

the main power and leave the doors

open. Ventilate the room thoroughly to

accelerate the process.

When defrosting is completed, clean

your freezer as described above.

WARNING!

Do not use sharp objects to remove

frost from the freezer compartment.

Only after the interior is completely

dry should the appliance be

switched back on and plugged

back into the main socket.

Take care to keep door seals clean.

Sticky food and drinks can cause seals

to stick to the cabinet and tear when

you open the door. Wash seal with a

mild detergent and warm water. Rinse

and dry it thoroughly after cleaning.

Door seals cleaning

CAUTION!

Only after the door seals are

completely dry should the

appliance be powered on.

Replacing the LED light

WARNING!

The LED light must be replaced

by a competent person. If the

LED light is damaged, follow the

steps below

1. Unplug your appliance.

2. Remove the light cover by

lifting up and pulling out.

3. Hold the LED light with one

hand and pull it while pressing

the connector latch with the

other hand.

4. Replace the LED light and

snap it correctly in place and

replace the light cover.

Energy Saving Tips

We recommend that you follow the tips

below to save energy.

Helpful Hints and Tips

Hints for fresh food refrigeration

Try to avoid keeping the door open for

long periods in order to conserve energy.

Ensure the appliance is away from any

sources of heat (direct sunlight, electric

oven or cooker etc.)

Don’t set the temperature colder than

necessary.

Don’t store warm food or evaporating

liquid in the appliance.

Place the appliance in a well ventilated

humidity freeroom. Please refer to

Installing your New Appliance chapter.

If the diagram shows the correct

combination for the drawers, crisper and

shelves, do not adjust the combination as

this is designed to be the most energy

efficient configuration.

Do not place hot food directly into the

refrigerator or freezer, the internal

temperature will increase resulting in the

compressor having to work harder and

consume more energy.

Do cover or wrap the food, particularly

if it has a strong flavor.

Place food properly so that air can

circulate freely around it.

Fruit and vegetables:

They should be stored in the special

drawer provided.

Butter and cheese:

Should be wrapped in airtight foil or

plastic film wrap.

Milk bottles:

Should have a lid and be stored in the

door racks.

When first starting-up or after a period

out of use, let the appliance run at least

2 hours on the higher settings before

putting food in the compartment.

Prepare food in small portions to enable

it to be rapidly and completely frozen

and to make it possible to subsequently

thaw only the quantity required.

Wrap up the food in aluminum foil or

cling wraps which are airtight.

Do not allow unfrozen food to touch the

food which is already frozen to avoid

temperature rise of the latter.

Hints for freezing

For Meat: (all types) wrap in cling wrap

and place on the glass shelf above the

vegetable drawer. Always follow food

storage times and use by dates

suggested by manufacturers.

Cooked food, cold dishes, etc.:

They should be covered and placed on

any shelf.

Hints for refrigeration

Hints for the storage of frozen food

Iced products (ice cubes, popsicles): if

consumed immediately after removal

from the freezer compartment, will

probably cause frost burns to the skin.

It is recommended to label and date

each frozen package in order to keep

track of the storage time.

Ensure that frozen food has been stored

correctly by the food retailer

Once defrosted, food will deteriorate

rapidly and should not be re-frozen. Do

not exceed the storage period indicated

by the food manufacturer.

Switching off your appliance

If the appliance needs to be switched off

for an extended period, the following

steps should be taken to prevent mold on

the appliance.

Remove all food.

Remove the power plug from the main

socket.

Clean and dry the interior thoroughly.

Ensure that all the doors are wedged

open slightly to allow air to circulate.

Trouble shooting

Problem Possible Cause & Solution

WARNING

•

If you experience a problem with your appliance or are concerned that the appliance is

not functioing correctly, you can carry out some easy checks before calling for service,

please see below.

1.Don’t try to repair the appliance yourself. If the problem persists after you have made

the checks mentioned below, contact a qualified electrician, authorized service

technician or the shop where you purchased the product.

2.A child entrapment warning statement is included below.

DANGER

Risk of child entrapment. Before you throw away your old refrigerator or freezer:

- Take off the doors.

- Leave the shelves in place so that children may not easily climb inside.

Appliance is

not working

correctly

Noise from the

appliance

Odors from the

compartments

Check whether the power cord is plugged into the power

outlet properly.

The room temperature may be too low. Try setting the

refrigerator or freezer temperature to a colder level to solve

this problem.

It is normal that the freezer is not operating during the defrost

cycle, or for a short time after the appliance is switched on to

protect the compressor.

Other unusual noises are due to the reasons below and may

need you to check and take action:

The cabinet is not level.

The back of appliance is touching the wall.

Bottles or containers have fallen or are rolling.

The sounds below are quite normal:

Compressor running noises.

Air movement noise from the small fan motor in the freezer

compartment or other compartments.

Gurgling sound similar to water boiling.

Popping noise during automatic defrosting.

Clicking noise before the compressor starts.

Clicking noise when you get the water.

The motor running noises when you get ice.

The interior may need to be cleaned

Some food, containers or wrapping may cause odors.

Check the fuse or circuit of your power supply, replace

if necessary.

It is normal to frequently hear the sound of the motor, it will

need to run more when in following circumstances:

Temperature setting is set colder than necessary.

Large quantity of warm food has recently been stored

within the appliance.

The motor runs

continuously

The motor runs

continuously

A layer of frost

occurs in the

compartment

Temperature

inside is too

warm

Temperature

inside is too cold

Doors can’t

be closed easily

Hear water

bubbling in the

refrigerator

The light is

not working

The LED light may be damaged. Refer to replace LED lights

in“ Cleaning and Care” chapter.

The control system has disabled the lights due to the door

being kept open too long. Close and reopen the door to

reactivate the lights.

The temperature outside the appliance is high.

Doors are kept open too long or too often.

After first installing the appliance or if it has been switched

off for a long time.

Check that the air outlets are not blocked by food and

ensure food is placed within the appliance to allow sufficient

ventilation. Ensure that door is fully closed. To remove the

frost, please refer to the Cleaning and Care chapter.

You may have left the doors open too long or too frequently;

or the doors are kept open by some obstacle; or the

appliance is located with insufficient clearance at the sides,

back and top.

Increase the temperature by following the “Display

Controls” chapter.

Check whether the top of the refrigerator is tilted back by

0.4"-0.6"(10-15mm) to allow the doors to self-close, or if

something inside is preventing the doors from closing.

This is normal. The bubbling comes from the refrigerant

coolant liquid circulating through the refrigerator.

•

Did you wait for 24 hours after installation of the water

supply line before making ice? If it is not sufficiently cool,

it may take longer to make ice, such as when first installed.

Is the water line connected and the water valve open?

Did you manually stop the ice making function? Make

sure you do not set the “Ice Off” mode.

Is there any ice blocked within the ice maker bucket?

Is the water pressure less than 30psi? Install a booster

pump to compensate for the low pressure.

Is the freezer temperature too warm? Try setting the

freezer temperature lower.

Ice maker is not making the ice fast enough. Please wait

for at least 90 minutes.

•

Is the water line connected and the water valve open?

Has the water line been crushed or kinked? Make sure the

waterline is free and clear of any obstruction.

Is the water tank frozen because the refrigerator

temperature is too low? Try selecting a warmer setting on

the display panel.

Check if the filter is properly installed. If it is not properly

installed, the water dispenser may not work.

Ice is not

making

Water dispenser

is not

functioning

Disposal of the Appliance

Correct Disposal of this product

DANGER

WARNING

Packaging materials with the recycle symbol are recyclable.

Dispose of the packaging into a suitable waste collection container to recycle it.

1. Pull out the main plug from the main socket.

2. Cut off the power cord and discard with the main plug.

Refrigerators contain refrigerant and gases in the insulation. Refrigerant and gases

must be disposed of professionally as they may cause eye injuries or ignition.

Ensure that tubing of the refrigerant circuit is not damaged prior to proper disposal.

This symbol on the product or in its packing indicates that

this product may not be treated as household waste.

Instead, it should be taken to the appropriate waste

collection point for the recycling of electrical and electronic

equipment. By ensuring this product is disposed of correctly,

you will help prevent potential negative consequences for

the environment and human health, which could otherwise

be caused by the inappropriate waste handling of this

product. For more detailed information about the recycling

of this product, please contact your local council, your

household waste disposal service, or the shop where you

purchased the product.

It is prohibited to dispose of this appliance as household waste.

Packaging materials

Before disposal of the appliance

Guía de uso y cuidado del refrigerador

Modelo: MRF266N6CSE

MRF211N6CSE

1-877-465-3566

Español

Gracias por elegir MORA. Estamos seguros de que cuando utilice su nuevo

refrigerador estará satisfecho. Sin embargo, antes de utilizar el aparato, le

recomendamos leer cuidadosamente todas estas instrucciones, las mismas brindan

detalles acerca de la instalación y uso del producto. Guarde una copia para

futuras referencias.

Introducción breve

Asegúrese de que todas las personas que

utilizan el electrodoméstico estén

familiarizadas con el funcionamiento y las

características de seguridad. Es

importante que instale el aparato

correctamente y preste atención a las

instrucciones de seguridad.

Le recomendamos conservar este manual

del usuario con el aparato para futuras

consultas.

Este aparato está diseñado para ser

utilizado en el hogar y las aplicaciones

similares tales como:

recomendamos leer cuidadosamente

todas estas instrucciones antes de utilizar

uso del producto. Este aparato no ha sido diseñado para que

lo utilicen personas (incluidos niños) con

capacidades físicas, sensoriales o mentales

reducidas, o con falta de experiencia o

conocimientos, a menos que estén

supervisados o reciban instrucciones acerca

del uso del aparato por parte de una

persona responsable de su seguridad.

Los niños deben estar supervisados para

garantizar que no jueguen con el aparato.

No almacene las sustancias explosivas tales

como latas de aerosol con un ipropulsor

inflamable en este aparato.

Conéctelo únicamente a un suministro de

agua potable.

No utilice los dispositivos mecánicos u

otros medios para acelerar el proceso de

descongelación, con excepción de los

recomendados por el fabricante.

No dañe el circuito de refrigerante.

No utilice los aparatos eléctricos dentro

de los compartimientos de

almacenamiento de alimentos del

aparato, a menos que sean de tipo

recomendado por el fabricante.

Para desechar el aparato, llévelo a un

centro autorizado de eliminación de

residuos. No lo expongan a llamas.

Si el cable de alimentación está dañado,

deberá ser reemplazado por el fabricante,

su agente de o las personas similarmente

cualificadas con el fin de evitar un peligro.

ADVERTENCIA

Cocinas en tiendas, oficinas y otros

ambientes de trabajo.

Hoteles, moteles y otro tipo residencial.

Posadas.

Servicios de hostelería y aplicaciones

similares no comerciales.

diario

recomienda seguir estas pautas.

las instrucciones de almacenamiento

nstrucciones importantes de seguridad

otras personas

No intente reparar el aparato usted

mismo. Es peligroso alterar las

especificaciones o modificar el

producto de cualquier modo.

Cualquier daño en el cable de

alimentación puede causar

cortocircuitos, incendios o

descargas eléctricas.

No ponga muchos alimentos en la

salida de aire de la pared trasera

del compartimento refrigerador o

congelador, pues puede afectar

notablemente a la circulación de

aire.

No coloque objetos calientes cerca

de los componentes de plástico de

este aparato.

volver a congelar una vez que se

haya descongelado.

No coloque bebidas enlatadas o

compartimiento del congelador.

paletas heladas o los cubos de

hielo directamente del congelador

ya que pueden causar

quemaduras de frío en la boca y

en los labios.

lejos de los niños para evitar el

riesgo de sofocación.

Proteja a los niños para que no se

quemen al tocar el compresor de

la parte trasera inferior del aparato.

No coloque objetos sobre el aparato,

ya que podrían provocar lesiones en

caso de caída.

Nunca permita que los niños jueguen

con el aparato colgándose o

subiéndose a las puertas, bandejas,

estantes, cajones, etc.

Desempaquete y compruebe

detenidamente el aparato. En caso de

mostrar daños evidentes, no enchufe

el aparato y póngase en contacto

inmediatamente con la tienda donde

lo compró. En este caso, conserve

todos los materiales de empaque.

Se recomienda esperar al menos 4

horas antes de conectar el aparato

para permitir que el refrigerante

regrese al compresor.

El electrodoméstico es apto para

fuentes de alimentación de corriente

alterna de fase simple de

110~115V/60Hz. Para un uso seguro, si

la oscilación de la tensión excede el

límite máximo, se debe colocar un

regulador de tensión automático de

CA de más de 350W en el refrigerador.

El enchufe eléctrico debe ser

accesible cuando el aparato esté

instalado.

Este aparato debe tener conexión a

tierra.

El aparato está equipado con un

conector que cumple con las normas

locales.

El conector debe ser apto para el uso

hogareño y debe estar equipado con

un tomacorriente que cumpla con las

normas vigentes.

Para evitar los riesgos siempre

presentes al utilizar un aparato

eléctrico, se recomienda prestar

atención a las siguientes instrucciones

acerca de electricidad.

Si el conector no es apto para su

tomacorriente, debe cortarlo y

eliminarlo cuidadosamente. Para

evitar posibles descargas eléctricas,

no coloque el conector que ya

eliminó en un tomacorriente. Si tiene

dudas, contacte a un electricista

matriculado y calificado.

No utilice cables de extensión ni

múltiples tomacorrientes ya que

podrían causar sobrecargas en el

siempre el electrodoméstico en un

tomacorriente individual que tenga

la misma capacidad de voltaje que

la placa.

eléctrico no esté aplastado ni

dañado. De lo contrario, puede

causar cortocircuitos, descargas

eléctricas o sobrecalentamiento y

causar incendios.

No inserte el enchufe eléctrico si la

toma está suelta, existe riesgo de

descarga eléctrica o incendio.

Apague el aparato y desconéctelo

del interruptor principal antes de

realizar la limpieza o moverlo.

Nunca desenchufe el aparato

tirando del cable eléctrico. Sujete

siempre el enchufe con firmeza y

tire hacia afuera del enchufe, para

evitar dañar el cable de

alimentación.

No utilice el aparato sin una

cubierta de iluminación interior.

La sustitución o reparación de los

componentes eléctricos las debe

realizar un electricista cualificado o

un ingeniero de servicio autorizado.

Solo se deben utilizar piezas de

repuesto originales.

No utilice aparatos eléctricos como

máquinas de helados dentro de los

compartimentos de

almacenamiento de alimentos del

aparato a menos que hayan sido

aprobados por el fabricante.

Para evitar lesiones en la vista, no mire

directamente a la luz LED ubicada en el

compartimiento del refrigerador. Si no

funciona correctamente, consulte con

un electricista cualificado y certificado o

sustitúyala en conformidad con el

capítulo “Limpieza y cuidado”.

El refrigerante isobutano (R600a) se

encuentra dentro del circuito

refrigerante del aparato. Asegúrese de

que ningún componente del circuito

refrigerante se haya dañado durante el

traslado y la instalación del aparato.

El refrigerante (R600a) es inflamable.

No almacene productos que

contengan propelentes inflamables

(ej.: latas de aerosol) o sustancias

explosivas en el electrodoméstico.

Evite llamas (velas, lámparas, etc.) y

otras fuentes de ignición.

Ventile completamente la habitación

donde se encuentra ubicado el

electrodoméstico.

Precaución: Riesgo de incendio

Refrigerante

Si el circuito refrigerante está dañado:

n ta ar e nue aparat

+50°F a + 90°F

+61°F a + 90°F

+61°F a + 100°F

+61°F a + 109°F

0.4"~0.6"

Debe instalar las manijas que se encuentran

en el compartimiento del refrigerador antes

de utilizar el aparato.

La manija más larga es la manija de la puerta

de la heladera y la manija más corta es la del

congelador.

Siga los siguientes procedimientos para instalar

y cambiar el lado de la manija.

Instalación de las manljas

(10-15mm)

Quite el cobertor del orificio del tornillo de la

puerta e instale el soporte de la manija (C).

Coloque la manija (A) en la puerta colocando la

manija sobre el soporte (C); luego, ajuste los

tornillos (B) con una llave Allen de 3 mm (que se

encuentra en la bolsa de plástico).

Herramientas que necesitará(No

incluidas):

Ajuste de la altura y el espacio

de la puerta

La altura de una puerta se puede ajustar

utilizando las juntas elásticas incluidas.

Herramientas que necesitará:

Anillo de retención (4 uds) Lave (No incluidas)

Para ajustar la altura de la puerta

1. Verifique la diferencia de altura entre

las puertas y luego levante y sostenga

la puerta más baja para que quede

nivelada con la otra.

2. Inserte una junta elástica de tamaño

adecuado entre la puerta y la bisagra,

tal como se muestra.

importante!

1.Inserte una sola junta elástica. Si inserta

dos o más juntas elásticas, es posible que

se salgan o produzcan un ruido de roce.

2.No levante demasiado la puerta. La

puerta puede entrar en contacto

con la cubierta superior y dañarla.

3.Guarde las juntas elásticas sobrantes

para un posible uso futuro.

10.

3. 2.

4. Retire las 4 tuercas de cabeza

(5/32”,4mm). Retire las bisagras de

la puerta inferior izquierda y

Desmontar la puerta del

congelador

Para quitar el recipiente (H) para

almacenar hielo, levántelo

siguiendo la dirección de la flecha.

Retire el cajón superior del

sistema de rieles.

quítela.

Retire el cajón inferior del

congelador (C) levantándolo.

Retire los 4 tornillos instalados en el

marco de soporte (D).

Coloque la puerta del congelador

y el cajón superior del congelador

Puede encontrar estos artículos en

congelador

después de trasladar el aparato a su

orden contrario.

electrodoméstico es el dispenser de

agua con filtro. Para ayudar a

agua elimina las partículas no

esteriliza ni destruye los

deba comprar un sistema de

funcione correctamente.

1 Virola

2. Llave de 1/2” o llave inglesa.

Válvula de cierre de

tipo montura uno y 1/4”

1 Acoplador 2 Pinza

realizarla un fontanero cualificado.

de agua fuera de sus límites podría

causar un mal funcionamiento,

segundos.

Primero, cierre el suministro de agua

principal.

Conectar la tubería de

suministro de agua

Línea de

agua fría

Abrazad

era

Válvula de

Cierre

Utilice un taladro eléctrico y una

broca de 1/4” para perforar la

línea de agua fría y conectar la

válvula de asiento.

3. Conecte el tubo de extensión de 1/4”

a la salida de la válvula de cierre.

Purgue la tubería. Abra el suministro

de agua principal y purgue la tubería

hasta que el agua salga limpia.

Luego, corte el agua de la válvula

después de drenar un cuarto de agua

por toda la tubería.

Válvula de

salida

Tuerca de

empaque

Tipo de Sillín Tipo de Sillín Tuerca de

compresión

Tubo de

extensión de

1/4”

Virola

(casquillo)

Conecte la tubería de extensión con

la línea detrás del refrigerador a través

del acoplador. Inserte

completamente la tubería de

extensión en el acoplador e inserte el

gancho en el acoplador para

asegurar la tubería. Haga lo mismo

con el otro extremo. Luego de insertar

ambos ganchos, compruebe que la

línea esté firme con el gancho.

Asegúrese de no apretar ni doblar la

línea de agua al momento de

realizar la instalación.

Esto puede hacer que el agua fluya

inadecuadamente a través de la

línea y afectar el funcionamiento del

refrigerador.

Pinza

Tuberías de

agua Tuberías de agua

Acoplador

Utilice solamente la tubería nueva

suministrada con el refrigerador. No

se debe utilizar la tubería vieja.

Después de conectar la línea de

agua, abra la válvula de agua para

purgar el filtro durante 5 minutos

antes del uso. La descoloración

oscura inicial del agua es normal. Es

normal que haya un sonido de

descarga saliendo del aparato al

conectar la línea de agua al

aparato y presionar la palanca del

dispenser por primera vez.

1. Se debe conectar la línea de

agua a la tubería de agua fría.

Si lo conecta a la tubería de

agua caliente, el purificador

podría fallar.

2. Evite contaminar la tubería

durante la instalación.

3. Sólo conéctelo a un suministro

de agua potable.

¡PRECAUCIÓN!

6. Abra el agua y compruebe si hay

fugas.

Verifique si hay fugas en las

conexiones de la línea de agua

Conexión de la tubería de agua

al refrigerador

a b c a

Patas inferiores

ajustables

despensa

Panel de control

Debido a las modificaciones incesantes de nuestros productos, su refrigerador puede

diferir un poco del de este manual de instrucciones pero sus funciones y métodos de uso

son los mismos.

Para obtener la mejor eficiencia energética de este producto, coloque los estantes,

cajones y recipientes en su posición original como se muestra en la imagen de arriba.

Nota:

Descripción del aparato

modo que controla la temperatura

de la heladera. Si toca el botón de

forma continua, la temperatura se

configurará con la siguiente

secuencia.

ontroles de la pantalla

primera vez, la retroiluminación de los

iconos de la pantalla empezarán a

botón o las puertas están cerradas, la

El panel de control consta de dos

áreas para la temperatura y un área

para los distintos modos.

Este botón controla la máquina de

” para controlar la cubitera. Si la

luz de la función

“” está encendida, la

cubitera está funcionando. Si desea

bloquear la cubitera, toque otra vez

el botón “ ” hasta que la

luz del botón se apague.

ajusta la temperatura media de

temperaturas del interior de cada

compartimento pueden variar de

la cantidad de comida que

ambientales elevadas o bajas

temperatura real del interior del

aparato.

Si desea disminuir el tiempo necesario

para enfriar los productos en el

frigorífico, toque este botón, el icono

” se iluminará, y la

configuración de la temperatura del

Super coolse apaga automáticamente

temperatura del refrigerador volverá al

ajuste anterior.

activada, puede tocar el botón “Super

En caso de que la heladera se apague,

la función no se guardará.

Freezer”

para activar el modo que controla la

pulse continuamente el botón, la

temperatura se ajustará en la secuencia

siguiente.

Fridge

Freezer

Ice

On/Off

Super

Cool

47°F - 46°F -45°F - 44°F -43°F - 42°F - 41°F

40°F

39°F -

38°F -

37°F -

36°F -

35°F -

6°F ~ 5°F ~ 4°F ~ 3°F ~ 2°F ~ 1°F ~ 0°F ~ -1°F ~ -2°F ~ -3°F ~ -4°F

-12°F ~ -11°F ~ -10°F ~ -9°F ~ -8°F ~ -7°F ~ -6°F ~ -5°F

Toque este botón si desea disminuir el

tiempo necesario para congelar los

productos en el congelador ícono Super

Freeze “ ” se iluminará y la pantalla de

temperatura del congelador mostrará

-12°F.

Super Freeze puede bajar rápidamente

la temperatura del congelador y

congelar la comida mucho más rápido

de lo normal. Esto conservará las

vitaminas y los nutrientes de los

alimentos frescos y mantendrá la

comida fresca durante más tiempo.

Super

Freezer

Super Freeze

botón.

botón las puertas han estado cerradas

durante más de un minuto.

Cuando se encienda el refrigerador,

todos los iconos del panel de control se

sonará un timbre.

La configuración de la temperatura

vuelve a la configuración anterior.

horas.

Super F

Si se corte la energía mientras el Super

Si desea cambiar de “ºF” a “ºC”,

mantenga presionados los botones

“Super Cool” y “ ”

agua.

Cuando el refrigerador haya

el icono de filtro “” parpadeará

filtro de agua.

Primeramente, necesita comprar un

comprar el filtro nuevo en el local

donde compró el refrigerador o en el

sistema de servicio de post venta de

mantenga presionado los botones

“” y “ ” durante

intermitente se apague. Cuando

vuelva a colocar el filtro de agua,

podría filtrarse un poco de agua del

fluya a un recipiente y limpie las fugas

Energy

Saving

frigorífico parece estar en

funcionamiento pero no genera aire frío.

Los indicadores en el panel de control

este modo, mantenga presionadas las

teclas “ ” y “ ” al

Puede tocar este botón para activar o

desactivar el modo de Ahorro de

energía. Cuando active el Ahorro de

energía, el icono Ahorro de energía “”

se iluminará. La temperatura de la

heladera cambia automáticamente a

42ºF y la del congelador a 2ºF. Si el modo

ahorro de energía está desactivado, el

ícono “ ” se apagará y la temperatura

volverá a su configuración previa.

durante más de 2 minutos, se activará la

presentará “dr”. La alarma se detendrá

cuando las puertas se cierren o se

puerta abierta por mucho tiempo

agua fresca y limpia del refrigerador.

sar seu aparelho

El dispenser de agua está ubicado en

el lado izquierdo de la heladera. Abra

las puertas del refrigerador y presione

el botón del dispenser de agua para

debajo de la palanca del dispenser

en la posición sugerida y presiónela.

Sostenga el vaso debajo del dispenser

soltar el botón del dispenser ya que el

de soltar el botón.

Si tiene problemas para liberar el filtro

de agua, utilice la herramienta que se

incluye en el paquete mencionado

grados en sentido antihorario (hacia

agua, guárdelo para uso futuro.

Nota

Para cambiar fácilmente el filtro de

agua, cierre la válvula del suministro

de agua.

A veces es difícil desarmar el filtro de

agua ya que las impurezas del agua

hacen que el filtro de pegue. Si tiene

estas dificultades, sujete firmemente el

filtro de agua y quítelo.

Al quitar el filtro, se puede filtrar un

poco de agua desde la abertura.

Esto es normal. Para minimizar las

fugas de agua, mantenga el

cartucho del filtro de forma horizontal

al momento de quitarlo.

Para evitar el desbordamiento, vacíe

la bandeja (M) del filtro de agua y

seque el armazón del filtro.

Siga las siguientes instrucciones para

insertar el nuevo filtro de agua.

aire y los contaminantes atrapados

en el sistema.

En algunos hogares se requiere de

una purga adicional.

agua provenientes del filtro de

agua.

del filtro.

Presione el filtro y gírelo hacia la

derecha hasta que quede

asegurado.

filtro de agua debido a la presión

suministro de agua.

vuélvalo a abrir.

Después de abrir el suministro de

fugas persisten, suspenda el uso y

llame al centro de atención al

de lo contrario, el agua puede gotear

desde el dispenser. Esto significa que

todavía hay aire en la línea.

continua. Deje de presionar y libere la

almohadilla del dispensador en ciclos

segundos apagado.

necesario.

Permita que el tanque de

almacenamiento en el sistema de

ósmosis inversa vuelva a llenarse

después del uso intensivo.

conjunto con un sistema de ósmosis

inversa. Para solucionarlo, quite el filtro

de agua.

sale por el sistema de ósmosis inversa

suministro de agua fría, el sistema de

ósmosis inversa necesita estar a un

la presión del agua hacia el sistema de

El compartimento de refrigerador es

apto para almacenar carnes, verduras y

fruta. Debe sellar los alimentos para

evitar la pérdida de humedad o para

que los sabores se impregnen en otros

alimentos.

¡PRECAUCIÓN!

Nunca cierre la puerta de la

nevera con las estanterías, el

cajón para verduras y/o guías

telescópicas extendidas.

Podrían dañarse, así como a la

nevera.

Uso del compartimiento del

refrigerador

Canastos de la puerta

¡ADVERTENCIA!

Estantes de vidrio

O N

Cajones de fruta y verduras

Uso del compartimiento del

congelador

Ice

On/Off

Siguiendo la instalación, deje que

el recipiente de almacenamiento de

un utensilio de plástico y elimínelo.

manera uniforme por la superficie.

Limpie las puertas, las asas y las

superficies del armario con

detergente suave y séquelas con

Limpie a y cuidado

no conecte el electrodoméstico

en el interruptor principal durante

apague el aparato y desconecte

detergente para autos,

lavandina, aceite, limpiadores

abrasivos o solventes orgánicos,

como por ejemplo benceno,

danificar a superfície do

Debe limpiar periódicamente el

interior del aparato. Le resultará más

fácil limpiarlo cuando tenga poca

cantidad de comida. Limpie el interior

del frigorífico y del congelador con

una solución suave de bicarbonato

de sodio y agua, y aclárelo todo con

agua tibia y una esponja o trapo bien

escurridos. Séquelo completamente

antes de volver a colocar los estantes

y cestas. Seque bien todas las

superficies y partes extraíbles antes de

volver a colocarlas.

Limpieza interior

¡ADVERTENCIA!

¡PRECAUCIÓN!

Sustituir la luz LED

¡ADVERTENCIA!

Consejos de ahorro de energía

Se recomienda seguir estos consejos

para ahorrar energía.

c c

Sugerencias para refrigerar

alimentos frescos

Sugerencias de congelación

Sugerencias de refrigeración

Recomendaciones para guardar

los alimentos congelados

Desligar o seu aparelho

Resolución de problemas

para niños.

PELIGRO

congelador usados:

La temperatura de la habitación puede ser muy baja.

congelador a un nivel más frío para resolver este problema.

Es normal que el congelador no funcione durante el ciclo de

descongelación automática, o durante un breve tiempo

Otros ruidos inusuales pueden ser debidos a los motivos

descritos a continuación y es posible que deba comprobarlos

y tomar medidas:

El armario no está nivelado.

La parte trasera del aparato toca la pared.

Las botellas o recipientes se caen o ruedan.

Los sonidos descritos a continuación son normales:

Ruido de funcionamiento del compresor.

Ruido de movimiento de aire del motor del ventilador pequeño

en el compartimento del congelador o los otros

compartimentos.

Sonido de borboteo parecido al del agua en ebullición.

Sonido de golpeteo durante la descongelación automática.

Chasquidos antes de que arranque el compresor.

Se escucha un chasquido al sacar agua.

Ruído de funcionamento do motor quando você recebe o gelo.

Es posible que sea necesario limpiar el interior.

olores.

Es normal escuchar con frecuencia el sonido del motor,

deberá funcionar con más potencia en las circunstancias

siguientes:

El ajuste de temperatura es más frío de lo necesario.

Se ha almacenado recientemente una gran cantidad de

comida caliente dentro del aparato.

El motor

funciona

continuamente

Hay una capa

de escarcha en

compartimento

La temperatura

interior es

demasiado

cálida

La temperatura

interior es

demasiado fría

Las puertas no se

pueden cerrar

fácilmente

Se escuchan

burbujas de agua

en el refrigerador

La luz no

funciona

rato

que las puertas se cierren.

La máquina de hielo no produce el hielo lo suficientemente

rápido.

no funcionar.

No está haciendo

el hielo

El dispenser de

agua no está

funcionando

Eliminación del aparato

Eliminación correcta del producto

PELIGRO

ADVERTENCIA

Materiales de embalaje

1. Desconecte el enchufe de la toma eléctrica.

2. Corte el cable eléctrico y elimínelo con el enchufe.

Los refrigeradores contienen refrigerante y gases en el aislamiento. Se debe

desechar el refrigerante y los gases de forma profesional, ya que podrían provocar

lesiones oculares o ignición.

Asegúrese de que los tubos del circuito refrigerante no estén dañados antes de

desechar correctamente el aparato.

Este símbolo en el producto o en su embalaje indica

que no se debe tratar como residuos domésticos. En su

lugar, se debe llevar al punto de recogida de residuos

adecuados para reciclar el equipo eléctrico y

electrónico. Al asegurarse de que este producto se

elimina correctamente, ayudará a prevenir las

consecuencias negativas potenciales para el entorno

y la salud humana, que de lo contrario podrían ser

causadas por la manipulación inadecuada de los

residuos de este producto. Para más información sobre

el reciclaje de este producto, contacte al municipio, al

servicio de recolección de desperdicios o a la tienda

donde compró el producto.

Está prohibido eliminar este aparato con los residuos domésticos.

Antes de eliminación del aparato

Los materiales de embalaje con el símbolo de reciclaje son reciclables.

Arroje el embalaje al contenedor de recogida de residuos adecuado para

reciclarlo.

Mora MRF266N6CSE El manual del propietario

Marca: Mora

Modelo: MRF266N6CSE

Categoría: Neveras

Tipo: El manual del propietario

Descargar PDF

informe

En otros idiomas

English: Mora MRF266N6CSE Owner's manual

Documentos relacionados

Mora MRB172N6AWE Manual de usuario

Mora MRF266N6CSE El manual del propietario

Mora MRF266N6CSE El manual del propietario

En otros idiomas

Documentos relacionados

Otros documentos