Samsung DV365ETBGWR/AC El manual del propietario

Marca: Samsung

Modelo: DV365ETBGWR/AC

Categoría: Secadoras de ropa eléctricas

Tipo: El manual del propietario

Este manual también es adecuado para

Gas and Electric Dryer

user manual

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service or accessory

parts, please register your product at or contact

www.samsung.com/register

1-800-SAMSUNG (726-7864)

DV365*

This manual is made with 100% recycled paper.

DV365-03064C-01_EN_20121018.indd 1DV365-03064C-01_EN_20121018.indd 1 2012-10-18  8:28:482012-10-18  8:28:48

2_ features

features

1. Extra Large Capacity

Ultra drying capabilities are at your fingertips! Now you can dry extra-large loads. Our ultra

large 7.3 cu.ft. capacity dryer circulates more air through your clothes, drying them faster for

a wrinkle-free result.

2. Various Drying Cycles & Fuzzy Logic Algorithm

Simply turn the Jog Dial to select one of the 9 automatic drying cycles, including normal

and heavy duty, or let the Fuzzy Logic Control measure the degree of dampness and

automatically set the drying time. Precision drying has never been easier than with Samsung.

3. Time Saving

Our cycles are designed with you in mind. All our dryers are designed to dry your clothes in

less time... just 42 minutes! Giving you time for more important things in life.

4. Energy Saving

Samsung dryers are super energy efficient. You can dry up to 3.01 pounds of laundry with

1kWh. Also, both the large capacity and Fuzzy Logic Control save energy by automatically

drying your clothes the most efficient way.

5. Easy Reversible Door

Our dryers will fit just about anywhere. The direction of our reversible door can be changed

easily.

6. Pedestal with Storage Drawers

An optional 15” pedestal is available to raise the dryer for easier loading and unloading.

It also offers a built-in storage drawer that can hold a 100 oz. bottle of detergent

7. Stacking (MODEL NO: SK-3A1, SK-4A, SK-5A)

Samsung’s Washers and Dryers can be stacked to maximize usable space.

The Dryer legs need to be removed to stack the Washer and Dryer. An optional stacking kit

is available for purchase from your Samsung retailer.

8. Sanitize course

This course allows you to sanitize garments by permeating high temperature heat deep into

the fabric during the drying cycle. Use this course to keep your bedding and curtains clean.

When selecting this cycle, 99.9% of all bacteria is eliminated through high temperature heat.

Use this cycle for clothing, bedding, towels, or other items needing sanitization.

This certification is conducted by NSF International, an independent third-party testing and

certification organization.

9. 4-way Vent (electric model only)

You can install the exhaust vent in the following four (4) positions: back, either side, bottom.

NSF Protocol P154

Sanitization Performance of

Residential Clothes Dryers

DV365-03064C-01_EN_20121018.indd Sec9:2DV365-03064C-01_EN_20121018.indd Sec9:2 2012-10-18  8:28:532012-10-18  8:28:53

safety instructions _3

SAVE THESE INSTRUCTIONS

safety instructions

Congratulations on your new Samsung Dryer. This manual contains valuable

information on the installation, use, and care of your appliance. Please take the

time to read this manual to take full advantage of your dryer’s many benefits and

features.

WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS

Warnings and Important Safety Instructions in this manual do not cover all possible conditions and

situations that may occur. It is your responsibility to use common sense, caution, and care when installing,

maintaining, or operating your dryer.

Always contact your manufacturer about problems or conditions you do not understand.

IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS

WARNING

Hazards or unsafe practices that may result in severe personal injury or

death.

Follow the information in this manual to minimize the risk of fire or explosion or

to prevent property damage, personal injury, or death.

Do not store or use gasoline or other flammable vapors and liquids near this or

any other appliance.

CAUTION

Hazards or unsafe practices that may result in minor personal injury or

property damage.

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions explicity.

Unplug the power plug from the wall socket.

Make sure the machine is grounded to prevent electric shock.

Call the service center for help.

WARNING - Risk of Fire

• Clothes dryer installation must be performed by a qualified installer.

• Install the clothes dryer according to the manufacturer’s instructions and local codes.

• Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type)

duct is installed, it must be of a specific type identified by the appliance manufacturer as

suitable for use with clothes dryers. Flexible venting materials are known to collapse, be

easily crushed, and trap lint. These conditions will obstruct clothes dryer airflow and increase

the risk of fire.

• To reduce the risk of severe injury or death, follow all installation instructions.

DV365-03064C-01_EN_20121018.indd Sec1:3DV365-03064C-01_EN_20121018.indd Sec1:3 2012-10-18  8:28:532012-10-18  8:28:53

4_ safety instructions

SAVE THESE INSTRUCTIONS

safety instructions

IMPORTANT SAFETY INSTRUCTION

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your

appliance, follow basic precautions, including the following:

1. Read all instructions before using this appliance.

2. Do not dry articles that have been previously cleaned in, washed in, soaked in,

or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive

substances, as they give off vapors that could ignite or explode.

3. Do not allow children to play on or in the appliance. Close supervision of children is

necessary when the appliance is used near children.

4. Before the appliance is removed from service or discarded, remove the door to the

drying compartment.

5. Do not reach into the appliance if the drum is moving.

6. Do not install or store this appliance where it will be exposed to the weather.

7. Do not tamper with controls.

8. Do not repair or replace any part of the appliance or attempt any servicing unless

specifically recommended in the user-maintenance instructions or in published user-

repair instructions that you understand and have the skills to carry out.

9. Do not use fabric softeners or products to eliminate static unless recommended by the

manufacturer of the fabric softener or product.

10. Clean lint screen before or after each load.

11. Do not use heat to dry articles containing foam rubber or similarly textured rubber-like

materials.

12. Keep area around the exhaust opening and adjacent surrounding areas free from the

accumulation of lint, dust, and dirt.

13. The interior of the appliance and exhaust duct should be cleaned periodically by

qualified service personnel.

14. Do not place items exposed to cooking oils in your dryer. Items contaminated with

cooking oils may contribute to a chemical reaction that could cause a load to catch fire.

State of California Proposition 65 Warnings:

The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of

California to publish a list of substances known to the State of California to cause cancer,

birth defects, or other reproductive harm, and requires businesses to warn of potential

exposure to such substances.

This product contains a chemical known to the State of California to cause cancer, birth

defects, or other reproductive harm. This appliance can cause low-level exposure to some

of the substances listed, including benzene, formaldehyde, and carbon monoxide.

Gas appliances may cause low-level exposure to some of the substances listed including

benzene, formaldehyde, carbon monoxide, and soot; as a result of possible incomplete

combustion of natural gas or LP fuels. Exposure to these substances can be minimized

further by properly venting the dryer to the outdoors.

WARNING

DV365-03064C-01_EN_20121018.indd Sec1:4DV365-03064C-01_EN_20121018.indd Sec1:4 2012-10-18  8:28:542012-10-18  8:28:54

safety instructions _5

SAVE THESE INSTRUCTIONS

WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not turn on the appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Clear the room, building or area of all occupants.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or the gas

supplier.

Read all instructions before using the appliance.

To reduce the risk of fire or explosion:

• Do not dry items that have been previously cleaned, washed, soaked, or spotted with

gasoline, dry cleaning solvents, or other flammable or explosive substances. They

emit vapors that could ignite or explode. Any material that has been in contact with a

cleaning solvent or flammable liquids or solids should not be placed in the dryer until all

traces of these flammable liquids or solids and their fumes have been removed.

There are many highly flammable items used in homes, such as acetone, denatured

alcohol, gasoline, kerosene, some liquid household cleaners, some spot removers,

turpentine, waxes, and wax removers

• Items containing foam rubber (may be labeled latex foam) or similarly textured rubber-

like materials must not be dried on a heat setting. Heated foam rubber materials can,

under certain circumstances, produce fire by spontaneous combustion.

Do not allow children or pets to play on, in, or in front of the appliance. Close supervision is

necessary when the appliance is used near children and pets.

Before discarding or removing your dryer from service, remove the door to the drying

compartment to prevent children or animals from becoming trapped inside.

Do not reach into the appliance when the drum is moving.

Do not install or store this appliance where it will be exposed to the weather.

Do not tamper with the controls.

Do not repair, replace, or attempt to service any part of the appliance unless specifi cally

instructed to in the user-repair instructions and only if you have the understanding and skills

to carry out the repair, replacement, or service procedure.

Do not use fabric softeners or products to eliminate static unless the softener or product is

recommended for use in dryers.

Clean the lint screen before or after each load.

Keep the area around the exhaust opening and surrounding areas free from lint, dust, and

dirt.

The interior of the dryer and exhaust duct should be cleaned periodically by qualified service

personnel.

WARNING

DV365-03064C-01_EN_20121018.indd Sec1:5DV365-03064C-01_EN_20121018.indd Sec1:5 2012-10-18  8:28:542012-10-18  8:28:54

6_ safety instructions

SAVE THESE INSTRUCTIONS

safety instructions

This appliance must be properly grounded. Never plug the power cord into a receptacle

that is not grounded adequately and in accordance with local and national codes. See the

installation instructions for information about grounding this appliance.

Do not sit on top of the dryer.

Because of continuing product improvements, Samsung reserves the right to change

specifications without notice. For complete details, see the Installation Instructions

packed with your product before selecting cabinetry, making cutouts, or beginning

installation.

Ensure pockets are free from small, irregularly shaped, hard objects, foreign material, etc.

ie. coins, knives, pins, etc. These objects could damage your dryer.

Do not wash clothing with large buckles, buttons, or other heavy metal or solid objects.

Gas leaks may occur in your system, resulting in a dangerous situation.

Gas leaks may not be detected by smell alone.

Gas suppliers recommend you purchase and install a UL-approved gas detector.

Install and use in accordance with the manufacturer’s instructions.

Do not place items in your dryer that have been spotted or soaked with vegetable oil or

cooking oil. Even after being washed, these items may contain significant amounts of these

oils.

Residual oil on clothing can ignite spontaneously. The potential for spontaneous

combustion increases when items containing vegetable oil or cooking oil are exposed to

heat. Heat sources such as your dryer can warm these items, allowing an oxidation reaction

in the oil to occur. Oxidation creates heat. If this heat cannot escape, the items can become

hot enough to catch fire. Piling, stacking, or storing these kinds of items may prevent heat

from escaping and can create a fire hazard.

All washed and unwashed fabrics that contain vegetable oil or cooking oil can be

dangerous. Washing these items in hot water with extra detergent will reduce, but not

eliminate, the hazard. Always use the Cool Down cycle for these items to reduce their

temperature. Never remove these items from the dryer hot or interrupt the drying cycle until

the items have run through the Cool Down cycle. Never pile or stack these items when they

are hot.

WARNING

DV365-03064C-01_EN_20121018.indd Sec1:6DV365-03064C-01_EN_20121018.indd Sec1:6 2012-10-18  8:28:542012-10-18  8:28:54

contents _7

contents

INSTALLING YOUR DRYER

8 Unpacking your dryer

8 The Dryer’s Exterior

9 Key installation requirements

9 Tools needed for installation

9 Replacement parts and accessories

10 Ducting requirements

12 Important to installer

12 Location considerations

12 Alcove or closet installation

13 Mobile home installation

13 Exhausting

14 Gas requirements

15 Electrical requirements

15 Grounding

16 Electrical connections

17 Installation - General procedure

19 Final installation checklist

20 Dryer Exhaust Tips

21 Door Reversal

22 Connecting the inlet hose

OPERATING INSTRUCTIONS, TIPS

24 Overview of the control panel

26 Child lock

26 Sound Off

27 Drying Rack (Optional Part)

28 Clean the lint filter

28 Load the dryer properly

28 Getting started

CARE AND CLEANING

29 Control Panel

29 Tumbler

29 Powder coated tumbler

29 Dryer Exterior

29 Dryer Exhaust System

SPECIAL LAUNDRY TIPS

30 Special laundry tips

TROUBLESHOOTING

31 Check these pointers if your dryer…

32 Information codes

APPENDIX

33 Fabric care chart

34 Protecting the environment

34 Declaration of conformity

34 Specifications

35 Cycle chart

DV365-03064C-01_EN_20121018.indd Sec3:7DV365-03064C-01_EN_20121018.indd Sec3:7 2012-10-18  8:28:542012-10-18  8:28:54

8_ installing your dryer

installing your dryer

UNPACKING YOUR DRYER

Unpack your Dryer and inspect it for shipping damage. If your Dryer was damaged during shipping,

contact 1-800-SAMSUNG (726-7864).To prevent personal injury or strain, wear protective gloves whenever

lifting or carrying the dryer.

Packing materials can be dangerous to children. Keep all packing material (plastic bags, polystyrene,

etc.) well out of children’s reach.

THE DRYER’S EXTERIOR

Parts supplied

“Y”-connector Short inlet hose Rubber Washer Long inlet hose

A Drying Rack is not supplied with this model. The Drying Rack is optional. You can purchase it

through a service center.

WARNING

Control panel

Adjustable legs

Filtro

Duct Exhaust

Water Inlet

[ BACK ]

DV365-03064C-01_EN_20121018.indd Sec11:8DV365-03064C-01_EN_20121018.indd Sec11:8 2012-10-18  8:28:542012-10-18  8:28:54

installing your dryer _9

KEY INSTALLATION REQUIREMENTS

Hire a professional to install this dryer properly. If a service call has to be made as a result of poor setup,

adjustment, or connection, it is considered the responsibility of the installer. If you install the dryer, you are

responsible.

Make sure you have everything necessary for proper installation:

• A GROUNDED ELECTRICAL OUTLET. See Electrical Requirements. See page 15.

• A POWER CORD for electric dryers (except Canada). See page 16.

• GAS LINES (if you are installing a gas dryer) must meet national and local codes.

• EXHAUST SYSTEM – must be rigid metal or flexible stiff-walled metal exhaust ducting. See the ducting

and exhaust requirements on pages 10 - 11 and 13 and the dryer exhaust tips on page 20.

TOOLS NEEDED FOR INSTALLATION

Gather the required tools and parts before starting the installation.

Read and follow the instructions provided with any tools listed here.

Tools and Parts

Pliers Cutting knife Pipe wrench (gas only) Nut drivers

Level Phillips Screwdriver Duct tape Wrench

REPLACEMENT PARTS AND ACCESSORIES

If your dryer requires replacement parts or accessories, contact the dealer from whom you purchased your

dryer or the SAMSUNG customer care center at 1-800-SAMSUNG (726-7864).

01 installing your dryer

DV365-03064C-01_EN_20121018.indd Sec11:9DV365-03064C-01_EN_20121018.indd Sec11:9 2012-10-18  8:28:542012-10-18  8:28:54

10_ installing your dryer

DUCTING REQUIREMENTS

• Use a 4-inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct.

• Do not use a smaller duct.

• Ducts larger than 4 inches (10.2 cm) in diameter can cause increased lint accumulation.

Lint accumulation should be cleaned regularly.

• If a flexible metal duct must be used, use the type with a stiff sheet metal wall. Do not use a flexible duct

with a thin foil wall. Serious blockage can result if the flexible metal duct is bent too sharply.

• Never install any type of flexible duct in walls, ceilings, or other concealed spaces.

• Only a rigid or flexible metal duct should be used for exhausting.

• Keep the exhaust duct as straight and short as possible.

• Secure joints with duct tape. Do not use screws.

• DO NOT EXHAUST DRYER INTO ANY WALL, CEILING, CRAWL SPACE, OR CONCEALED SPACE OF

A BUILDING, GAS VENT, OR ANY OTHER COMMON DUCT OR CHIMNEY. THIS COULD CREATE A

FIRE HAZARD FROM LINT EXPELLED BY THE DRYER.

• A plastic flexible duct can kink, sag, be punctured, reduce airflow, extend drying times, and affect dryer

operation.

• Exhaust systems longer than recommended can extend drying times, affect machine operation, and

may collect lint.

• The exhaust duct should end with an exhaust hood that has a swing-out damper to prevent back drafts

and the entry of wildlife. Never use an exhaust hood with a magnetic damper.

• The hood should have at least 12 inches (30.5 cm) of clearance between the bottom of the hood and

the ground or other obstruction. The hood opening should point down.

• Never install a screen over the exhaust outlet.

• To avoid lint buildup, do not exhaust the dryer directly into a window well. Do not exhaust under a house

or porch.

• If exhaust ductwork must run through an unheated area, the duct should be insulated and slope slightly

down towards the exhaust hood to reduce condensation and lint buildup.

• Inspect and clean the interior of the exhaust system at least once a year. Unplug the power cord before

cleaning.

• Check frequently to be sure the exhaust hood damper opens and closes freely.

• Check once per month, and clean at least one time per year. Note: If clothes are not getting dry, then

check ducting for obstructions.

ELECTRIC AND GAS DRYER

Weather Hood Type

Recommended Use only for short-run installation

4” (10.16 cm) 2.5” (6.35 cm)

No. of 90° elbows Rigid Metallic Flexible* Rigid Metallic Flexible*

0 24.4 m (80 ft.) 12.4 m (41 ft.) 22.6 m (74 ft.) 10.1 m (33 ft.)

1 20.7 m (68 ft.) 11.2 m (37 ft.) 18.9 m (62 ft.) 8.8 m (29 ft.)

2 17.4 m (57 ft.) 10.1 m (33 ft.) 15.5 m (51 ft.) 7.6 m (25 ft.)

3 14.3 m (47 ft.) 9.0 m (29 ft.) 12.5 m (41 ft.) 6.5 m (21 ft.)

* Do not use non-metallic flexible duct.

installing your dryer

DV365-03064C-01_EN_20121018.indd Sec11:10DV365-03064C-01_EN_20121018.indd Sec11:10 2012-10-18  8:28:552012-10-18  8:28:55

installing your dryer _11

If the new Dryer is being installed into an existing exhaust system, you must

make sure:

• The exhaust system meets all local, state, and national codes.

• That a flexible plastic duct is not used.

• To Inspect and clean all lint buildup from inside the existing duct.

• The duct is not kinked or crushed.

• The exhaust hood damper opens and closes freely.

The static pressure in any exhaust system must not exceed 0.83 inches of water column or be

less than 0.

This can be measured while the Dryer is running with a manometer at the point where the

exhaust duct connects to the Dryer. A no-heat setting should be used. The Dryer tumbler should

be empty and the lint filter clean.

01 installing your dryer

DV365-03064C-01_EN_20121018.indd Sec11:11DV365-03064C-01_EN_20121018.indd Sec11:11 2012-10-18  8:28:552012-10-18  8:28:55

12_ installing your dryer

installing your dryer

IMPORTANT TO INSTALLER

Please read the following instructions carefully before installing the dryer. These instructions should be kept

for future reference.

REMOVE THE DOOR FROM ALL DISCARDED APPLIANCES TO AVOID THE DANGER OF A CHILD

SUFFOCATING.

LOCATION CONSIDERATIONS

Locate the Dryer where there is enough space at the front for loading and enough space behind for the

exhaust system. This Dryer is factory-ready for rear exhaust. To exhaust out the bottom or the left, use

the accessory exhaust kit. Instructions are included with the kit. It’s important to make sure the room has

enough fresh air. The Dryer must be located where there is no air-flow obstruction.

For gas Dryers, you must provide the clearance noted on the data plate to ensure adequate air for

combustion and proper Dryer operation.

DO NOT INSTALL OR STORE THE DRYER IN AN AREA WHERE IT WILL BE EXPOSED TO WATER AND/

OR WEATHER. KEEP THE DRYER AREA CLEAR OF COMBUSTIBLE MATERIALS, GASOLINE, AND

OTHER FLAMMABLE VAPORS AND LIQUIDS. A DRYER PRODUCES COMBUSTIBLE LINT. THE AREA

AROUND THE DRYER SHOULD BE KEPT LINT-FREE.

ALCOVE OR CLOSET INSTALLATION

You must exhaust the dryer to the outside to reduce the risk of fire when installed in an alcove or

closet.

• No other fuel-burning appliance should be installed in the same closet as the Dryer.

• WARNING: To reduce the risk of fire, YOU MUST EXHAUST THIS DRYER TO THE OUTDOORS.

See the EXHAUST INFORMATION section.

• Minimum clearances between the Dryer and adjacent walls or other surfaces are:

2” in front, 17” on top, 1” on either side, and 5” in the back.

• The closet front must have two unobstructed air openings for a combined minimum total area of 72 in²

with 3” minimum clearance on the top and bottom. A louvered door with equivalent space clearance is

acceptable.

WARNING

DV365-03064C-01_EN_20121018.indd Sec11:12DV365-03064C-01_EN_20121018.indd Sec11:12 2012-10-18  8:28:552012-10-18  8:28:55

installing your dryer _13

MOBILE HOME INSTALLATION

The installation of the Dryer in mobile homes must conform to the Manufactured Home Construction and

Safety Standard Title 24 CFR, Part 32-80 {formerly the Federal Standard for Mobile Home Construction and

Safety, Title 24, HUD (Part 280), 1975} for the United States) or CSA Standards Z240 (for Canada).

When installing a Dryer in a mobile home, you must make provisions for anchoring the dryer to the floor.

Locate the dryer in an area that has adequate fresh air.

A minimum of 72 in² (465 cm²) of unobstructed space is required.

Call 1-800-SAMSUNG (726-7864) for information about purchasing the Floor Anchoring Kit as an accessory.

All mobile home installations must be exhausted to the outside with the exhaust duct termination securely

fastened to the mobile home structure, using materials that will not support combustion.

The exhaust duct may not terminate underneath the mobile home.

See Exhausting section for more information.

EXHAUSTING

Exhausting the Dryer to the outside will prevent large amounts of lint and moisture from being blown into the

room.

In the United States:

• All dryers must be exhausted to the outside.

• The required exhaust duct is 4 inches (102 mm) in diameter.

• Use only those foil-type flexible ducts, if any, specifically identified for use with the appliance

by the manufacturer and that comply with the Outline for Clothes Dryer Transition Duct,

Subject 2158A.

• Do not assemble the duct with screws or other fasteners that extend into the duct and can

catch lint.

In Canada:

• Use only those foil-type flexible ducts, if any, specifically identified for use with the appliance

by the manufacturer.

• All dryers must be exhausted to the outside.

• The exhaust duct should be 4 inches (102 mm) in diameter.

Outside the U.S. and Canada:

• Refer to the local codes.

You must exhaust the dryer to the outside to reduce the risk of fi re when you install the

dryer in an alcove or closet.

NEVER USE A PLASTIC OR NON-METAL FLEXIBLE DUCT.

If your existing ductwork is plastic, non-metal, or combustible, replace it with metal.

Use only a metal exhaust duct that is non-flammable to ensure containment of exhaust air,

heat, and lint.

01 installing your dryer

WARNING

DV365-03064C-01_EN_20121018.indd Sec11:13DV365-03064C-01_EN_20121018.indd Sec11:13 2012-10-18  8:28:552012-10-18  8:28:55

14_ installing your dryer

installing your dryer

GAS REQUIREMENTS

Use only natural or LP (liquid propane) gases.

THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL

CODES, WITH THE NATIONAL FUEL GAS CODE ANSI/Z223.1, LATEST REVISION (FOR THE UNITED

STATES), OR WITH THE CAN/CGA-B149 INSTALLATION CODES (FOR CANADA).

Gas dryers are equipped with a burner vent for use with natural gas. If you plan to use your dryer with LP

(liquid propane) gas, it must be converted for safe and proper performance by a qualified service technician.

A 1/2” (1.27 cm) gas supply line is recommended and must be reduced to connect to the 3/8” (1 cm) gas

line on your dryer. The National Fuel Gas Code requires that an accessible, approved manual gas shut-off

valve be installed within 6’ of your dryer.

Gas dryers installed in residential garages must be raised 18 inches (46 cm) above the floor.

Additionally, a 1/8” (0.3 cm) N.P.T. (National Pipe Thread) plugged tapping, accessible for test gauge

connection, must be installed immediately upstream of your dryer’s gas supply connection.

Your Dryer must be disconnected from the gas supply pipe system during any pressure testing of the

system.

DO NOT reuse old flexible metal gas lines. Flexible gas lines must be design certified by the American Gas

Association (CGA in Canada).

• Any pipe joint compound used must be resistant to the action of any liquefied petroleum gas.

• As a courtesy, most local gas utilities will inspect a gas appliance installation.

GAS IGNITION – Your Dryer uses an automatic ignition system to ignite the burner.

There is no constant burning pilot.

Commonwealth of Massachusetts installation instructions

Your Dryer must be installed by a licensed plumber or gas fitter. A “T” handle manual gas valve

must be installed in the gas supply line to your dryer. If a flexible gas connector is used to install

your Dryer, the connector can be no longer than 3’ (36”).

- Gas leaks may occur in your system, creating a dangerous situation.

- Gas leaks may not be detected by smell alone.

- Gas suppliers recommend you purchase and install a UL-approved gas detector.

- Install and use in accordance with manufacturer’s instructions.

WARNING

DV365-03064C-01_EN_20121018.indd Sec11:14DV365-03064C-01_EN_20121018.indd Sec11:14 2012-10-18  8:28:552012-10-18  8:28:55

installing your dryer _15

ELECTRICAL REQUIREMENTS

A Wiring diagram is located on the back of the dryer.

• Improper connection of the equipment grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or serviceman if you are in doubt as to whether your Dryer is

properly grounded. Do not modify the plug provided with your Dryer – if it doesn’t fit the outlet,

have a proper outlet installed by a qualified electrician.

• To prevent unnecessary risk of fire, electrical shock, or personal injury, all wiring and grounding

must be done in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA No. 70-Latest Revision (for the U.S.) or the Canadian Electrical Code

CSA C22.1 – Latest Revisions and local codes and ordinances. It is your responsibility to provide

adequate electrical services for your Dryer.

• All gas installations must be done in accordance with the national Fuel Code ANSI/Z2231 – Latest

Revision (for the U.S.) or CAN/CGA – B149 Installation Codes – Latest Revision (for Canada) and

local codes and ordinances.

GROUNDING

This Dryer must be grounded. In the event of a malfunction or breakdown, the ground will reduce the risk of

electrical shock by providing a path of least resistance for the electrical current.

Gas models

Your Dryer has a cord with an equipment-grounding conductor and a grounding plug.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

Do not modify the plug provided with your Dryer – if it doesn’t fit the outlet, have a proper outlet

installed by a qualified electrician.

NEVER CONNECT THE GROUND WIRE TO PLASTIC PLUMBING LINES, GAS LINES, OR HOT

WATER PIPES.

Electric models

Your Dryer requires a cord with an equipment-grounding conductor and a grounding plug which

is sold separately.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

Do not modify the plug provided with your Dryer – if it doesn’t fit the outlet, have a proper outlet

installed by a qualified electrician.

If a power cord is not used and the Electric Dryer is to be permanently wired, the Dryer must

be connected to a permanently grounded metal wiring system, or an equipment grounding

conductor must be run with the circuit conductors and connected to the equipment grounding

terminal.

01 installing your dryer

WARNING

DV365-03064C-01_EN_20121018.indd Sec11:15DV365-03064C-01_EN_20121018.indd Sec11:15 2012-10-18  8:28:552012-10-18  8:28:55

16_ installing your dryer

installing your dryer

ELECTRICAL CONNECTIONS

Before operating or testing, follow all grounding instructions in the Grounding section.

An individual branch (or separate) circuit serving only your Dryer is recommended. DO NOT USE AN

EXTENSION CORD.

Gas models – U.S. and Canada

A 120 volt, 60 Hz AC approved electrical service, with a 15-amp fuse or circuit breaker is

required.

Electric models – U.S. only

Most U.S. dryers require a 120/240 volt, 60 Hz AC approved electrical service. Some require

120/208 volt, 60 Hz approved electrical service. The electric service requirements can be found

on the data label located behind the door. A 30-amp fuse or circuit breaker on both sides of the

line is required.

• If a power cord is used, the cord should be plugged into a 30-amp receptacle.

• The power cord is NOT provided with U.S. electric model dryers.

IMPORTANT:

When local codes allow, you can connect the dryer’s electrical supply with a new power supply

cord kit, marked for use with a dryer, that is U.L. listed and rated at a minimum of 120/240 volts,

30-amp with three No. 10 copper wire conductors terminated with closed loop terminals, open-

end spade lugs with turned up ends, or with tinned leads.

• Do not reuse a power supply cord from an old Dryer. The power cord electric supply wiring

must be retained at the dryer cabinet with a suitable UL-listed strain relief.

• Grounding through the neutral conductor is prohibited for (1) new branch-circuit installations,

(2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit

grounding through the neutral conductor. (Use 4-prong plug for 4 wire receptacle, NEMA

type 14-30R.)

Electric models – Canada Only

• A 120/240 volt, 60 Hz AC approved electrical service fused through a 30-amp fuse or circuit

breaker on both sides of the line is required.

• All Canadian models are shipped with the power cord attached. The power cord should be

plugged into a 30-amp receptacle.

You may not convert a dryer in Canada to 208 volts.

DV365-03064C-01_EN_20121018.indd Sec11:16DV365-03064C-01_EN_20121018.indd Sec11:16 2012-10-18  8:28:552012-10-18  8:28:55

installing your dryer _17

Installation - General procedure

For proper installation, we recommend that you hire a qualified installer.

Read these instructions completely before you begin the installation.

To install the dryer, follow these steps:

1. Move your dryer to an appropriate location for installation. Consider installing the dryer and washer side-

by-side so you have easy access to both appliances.

To move the dryer easily, lay two of the carton cushion-tops on the floor. Tip your dryer on its side so it

lies across both cushion-tops. Push the dryer so that it is near its final location. Set your dryer upright.

Leave enough room around the dryer so you can attach the duct work, power cord, etc.

2. If you need to change the direction of the door, go to Door Reversal on page . When done, return to

Step 3 below.

3. Review the Exhausting section before installing the exhaust system. Install the duct work from your

dryer to the exhaust hood. The crimped end of the duct sections must point away from your dryer. DO

NOT use sheet metal screws when assembling ducting. These joints should be taped. Never use plastic

flexible exhaust material.

A tip for tight installations: Attach a section of the exhaust system to your dryer before putting it in

place. Use duct tape to secure this section to your dryer, but do not cover the ventilation slots at the

back of the dryer cabinet.

4. If you have an electric model, skip to Step 6. If you have a gas model, go to the next step.

5. Review the Gas Requirements section, then follow the lettered steps below.

a. Remove the pipe thread protective cap.

b. Apply pipe joint compound or about 1 1/2 wraps of Teflon tape over all threaded connections.

The pipe joint compound must be resistant to the action of any liquefied petroleum gas.

c. Connect the gas supply to your dryer. An additional fitting is required to connect the 3/4” (1.9 cm)

female thread end of a flexible connector to the 3/8” (1 cm) male threaded end on the dryer.

d. Securely tighten the gas line fitting over the threads.

e. Turn on the gas supply. Check all gas connections for leaks using a soap solution. If bubbles

appear, tighten the connections and recheck. DO NOT use an open flame to check for gas leaks.

f. Go to Step 6 on the next page

01 installing your dryer

DV365-03064C-01_EN_20121018.indd Sec11:17DV365-03064C-01_EN_20121018.indd Sec11:17 2012-10-18  8:28:552012-10-18  8:28:55

18_ installing your dryer

installing your dryer

6. Review the Electrical Requirements section, then follow the 3 Wire

system connection instructions (Step 7) or 4 Wire system instructions

(Step 8) below.

7. Three Wire system instructions:

a. Loosen or remove the center terminal block screw.

b. Connect the neutral wire (white or center wire) of the power cord

to the center, silver-colored terminal screw of the terminal block.

Tighten screw.

c. Connect the other wires to outer terminal block screws. Tighten

screws.

d. Tighten the strain relief screws.

e. Insert the tab of the terminal block cover into your dryer’s rear

panel slot.

f. Secure the cover with a hold-down screw.

g. BEFORE OPERATING OR TESTING, follow the grounding

instructions in the Grounding section.

If converting from a 4-wire electrical system to a 3-wire,

you must connect the ground strap to the terminal block

support to ground the dryer frame to the neutral conductor.

We recommend using Ring terminals. If you use Strap

terminals, please ensure you install them perfectly.

8. Four Wire System instructions:

a. Remove the center terminal block screw.

b. Connect the ground wire (green or unwrapped) of the power cord

to the external ground conductor screw.

c. Connect the neutral wire (white or center wire) of the power cord

and the appliance ground wire (green with yellow stripes) under

the central screw of the terminal block.

d. Connect the other wires to the outer terminal block screws.

Tighten screws.

e. Tighten the strain relief screws.

f. Insert the tab of the terminal block cover into your dryer’s rear

panel slot.

g. Secure the cover with a hold-down screw.

h. BEFORE OPERATING OR TESTING, follow the grounding

instructions in the Grounding section.

We recommend using Ring terminals. If you use Strap

terminals, please ensure you install them perfectly.

WARNING

1. External ground connector

2. Neutral grounding wire

(green/yellow) from dryer

wiring harness

3. Center silver-colored

terminal block screw

4. Neutral wire (white or center

wire) from power cord.

5. 3/4” (1.9 cm) UL listed

strain relief

B - Black, W - White,

R - Red

Three Wire System

B W R

1. External ground connector

2. Green or bare copper wire

from power cord

3. 3/4 in. (1.9 cm) UL listed

strain relief

4. Center silver-colored

terminal block screw

Grounding wire (green/yellow)

from dryer wiring harness

6. Neutral wire (white or center

wire) from power cord

B - Black, W - White,

R - Red, G - Green

Four Wire System

B W R

DV365-03064C-01_EN_20121018.indd Sec11:18DV365-03064C-01_EN_20121018.indd Sec11:18 2012-10-18  8:28:552012-10-18  8:28:55

installing your dryer _19

U.S. MODELS:

IMPORTANT – All U.S. models are designed for a 3-WIRE SYSTEM CONNECTION. The dryer frame is

grounded to the neutral conductor at the terminal block. A 4-WIRE SYSTEM CONNECTION is required for

new or remodeled construction, mobile homes, or if local codes do not permit grounding through neutral.

If you use the 4-wire system, you cannot ground the dryer frame to the neutral conductor at the terminal

block.

Refer to the following instructions for 3- and 4-WIRE SYSTEM CONNECTIONS:

Remove the terminal block cover plate. Insert the power cord with a UL-listed strain relief through the hole

provided in the cabinet near the terminal block.

A strain relief must be used. Do not loosen the nuts already installed on the terminal block. Be sure they are

tight. Use a 3/8” (1 cm) deep well socket.

9. To ensure that the dryer provides optimal drying performance, it must

be level. To level the dryer, follow the lettered steps below:

a. Using a level, check if the dryer is level side to side and then front

to back.

b. If the dryer is not level, adjust the leveling feet on the bottom of

the dryer until the washer is level side to side and back to front.

Turning the feet clockwise retracts the feet. Turning the feet

clockwise loosens and extends them.

To set the dryer to the same height as the washer, fully

retract the leveling feet by turning them counterclockwise,

then loosen the feet by turning them clockwise. Once

the dryer is the same height as the washer, follow the

directions above to level the dryer.

Adjust the leveling feet only as much as necessary to level the dryer. Extending the leveling

feet more than necessary can cause the dryer to vibrate.

10. Make sure all gas connections (on gas models), exhaust, and electrical connections are complete. Plug

in your dryer, and then check its operation by using the checklist below.

11. For GAS MODELS ONLY

The burner may not ignite initially due to air in the gas line. Allowing your dryer to operate on a heat

setting will purge the line. If the gas does not ignite within 5 minutes, turn your dryer off and wait 5

minutes. Be sure the gas supply to your dryer has been turned on. To confirm gas ignition, check the

exhaust for heat.

FINAL INSTALLATION CHECKLIST

 The dryer is plugged into an electrical outlet and is properly grounded.

 The exhaust ductwork is hooked up and joints are taped.

 You have used rigid or stiff-walled flexible metal duct material, not plastic flexible duct.

 The dryer is leveled and is sitting firmly on the fl oor.

 For gas models: The gas is turned on and there are no gas leaks.

 Start your dryer to confirm that it runs, heats, and shuts off.

01 installing your dryer

Level

Leveling feet

Retract fully Then loosen

DV365-03064C-01_EN_20121018.indd Sec11:19DV365-03064C-01_EN_20121018.indd Sec11:19 2012-10-18  8:28:562012-10-18  8:28:56

20_ installing your dryer

installing your dryer

DRYER EXHAUST TIPS

Plastic or non-metal flexible duct presents a potential fire hazard.

1. Make sure your dryer is installed properly so it exhausts air

easily.

2. Use a 4” diameter rigid metal duct. Tape all joints, including

at the dryer.

Never use lint-trapping screws.

3. Keep ducts as straight as possible.

4. Clean all old ducts before installing your new dryer.

Be sure the vent flap opens and closes freely.

Inspect and clean the exhaust system annually.

Don’t let a poor exhaust system slow drying by:

1. Restricting your dryer with a poor exhaust system.

2. Using a plastic, thin foil, or non-metal flexible duct.

3. Using unnecessarily long ducts that have many

elbows.

4. Using crushed or clogged vent or ducts.

WARNING

1 2

3 4

DV365-03064C-01_EN_20121018.indd Sec11:20DV365-03064C-01_EN_20121018.indd Sec11:20 2012-10-18  8:28:562012-10-18  8:28:56

installing your dryer _21

DOOR REVERSAL

1. Unplug the power cord.

2. Remove two door hinge

screws.

3. Lift the door and remove

it.

8. Reinsert the black screw

in the other hole.

4. Remove a screw on the

Frame Front.

9. Reinsert the screw (Step

4) on the Frame Front.

5. Remove the two screws

on the opposite side of

the door hinge.

10. Place the door on the

other side and reattach it

to the dryer.

6. Remove two screws from

the holder lever.

11. Reattach the holder lever.

7. Remove one black screw

from the door hinge.

12. Reattach the screws in

the remaining holes.

01 installing your dryer

DV365-03064C-01_EN_20121018.indd Sec11:21DV365-03064C-01_EN_20121018.indd Sec11:21 2012-10-18  8:28:562012-10-18  8:28:56

22_ installing your dryer

CONNECTING THE INLET HOSE

Method1 - Using the Y Connector and Long Hose

The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old

hoses.

1. Turn off the cold water faucet.

2. If you have a washer water hose attached to the cold water

faucet, unscrew and remove the hose.

3. If space permits, attach the brass female end of the

“Y”connector to the cold water faucet. Turn by hand until

tight.

4. Attach the straight end of the long hose to the “Y’

connector. Screw on the hose coupling by hand until it is

tight.

5. Using pliers, tighten the hose coupling with an additional

two thirds turn.

Do not overtighten. You can damage the coupling.

6. Attach the angled end of the long hose to the fill valve at

the bottom of the dryer’s rear frame. Screw on the coupling

by hand until it is tight.

7. Using pliers, tighten the hose coupling with an additional

two thirds turn.

Do not overtighten. You can damage the coupling.

8. Attach the water hose to the other side of the “Y” connector. Screw on the hose coupling

until it is tight. Using pliers, tighten the coupling with an additional two thirds turn.

Do not overtighten. You can damage the coupling.

9. Turn the water faucet on.

10. Check for leaks around “Y” connector, faucets, and hoses.

Do not overtighten, as it may damage the coupling.

9. Check that the water faucets are on.

10. Check for leaks around “Y” connector, faucets and hoses.

Duct Exhaust

Frame

(back)

Water Hose

Y-Connector

Water Hose

installing your dryer

DV365-03064C-01_EN_20121018.indd Sec11:22DV365-03064C-01_EN_20121018.indd Sec11:22 2012-10-18  8:28:572012-10-18  8:28:57

installing your dryer _23

Method2 - Using the Short Hose, Long Hose, and Y Connector

The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old

hoses.

If the “Y” connector cannot be attached directly to the cold

water faucet, then you must use the short hose.

1. Turn off the cold water faucet.

2. If you have a washer water hose attached to the cold water

faucet, unscrew and remove the hose.

3. Attach the short inlet hose to the cold water faucet. Screw

on the coupling by hand until it is tight.

4. Using pliers, tighten the coupling with an additional two

thirds turn.

Do not overtighten. You can damage the coupling.

5. Attach the ‘Y” connector to the stainless male end of the

small hose. Screw on the coupling by hand until it is tight.

6. Using pliers, tighten the coupling with an additional two

thirds turn.

Do not overtighten. You can damage the coupling.

7. Attach the angled end of the long hose to the fill valve at the

bottom of the dryer rear frame. Screw on the coupling by

hand until it is tight.

8. Using pliers, tighten the coupling with an additional two thirds turn.

Do not overtighten. You can damage the coupling.

9. Turn the water faucet on.

10. Check for leaks around “Y” connector, faucets, and hoses.

Short hose

(Inlet to cold

water)

“Y’ connector

Long hose

01 installing your dryer

DV365-03064C-01_EN_20121018.indd Sec11:23DV365-03064C-01_EN_20121018.indd Sec11:23 2012-10-18  8:28:572012-10-18  8:28:57

24_ operating Instructions, tips

Cycle Selector

To select a cycle, rotate the Cycle Selector dial to the desired cycle.

The indicator light by the cycle name will illuminate. The Normal, Heavy Duty, Perm

Press, Delicates and Sanitize cycles are Sensor Dry cycles. Sensor Dry automatically

senses the moisture in the load and shuts the dryer off when the load reaches the

dryness level (Very Dry to damp dry) you selected.

Normal – Use this cycle to dry loads of cotton, underwear, and linen.

Heavy Duty – Use this cycle to dry heavy fabrics such as jeans, corduroys, or work

clothes with high temperature heat.

Perm Press – Dry wrinkle-free cottons, synthetic fabrics, knits, and permanent press

fabrics automatically.

Delicates – The Delicates cycle is designed to dry heat-sensitive items at a low drying

temperature.

Sanitize - Lets you sanitize garments by infusing high temperature heat deep into the

fabric during the drying cycle. Use this cycle to keep your bedding and curtains clean

through sanitization.

Time Dry – Time Dry allows you to select the desired cycle time in minutes. Turn the

Cycle Selector dial to Time Dry, and then press the Time Key arrow to set the drying

time.

Press the arrow repeatedly to scroll through the time settings.

Quick Dry – Provides a 30 minute drying cycle.

Refresh – This cycle is best for smoothing out wrinkles and reducing odors from loads

consisting of one to four dry items. In this cycle a small amount of water is sprayed into

the dryer drum after several minutes of tumbling with heat.

Wrinkle Away – The Wrinkle Away cycle removes wrinkles from clothes stored in

closets, etc. It provides a wrinkle release via optimized steam care. You can change the

drying time.(Minimum time : 20 minutes) *For best results, load no more than 3 items.

operating Instructions, tips

To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFTY

INSTRUCTION before operating this appliance.

OVERVIEW OF THE CONTROL PANEL

2 4

73 8

WARNING

DV365-03064C-01_EN_20121018.indd Sec5:24DV365-03064C-01_EN_20121018.indd Sec5:24 2012-10-18  8:28:572012-10-18  8:28:57

operating Instructions, tips _25

Digital Graphic

Display

The display window shows the estimated time remaining in the cycle after you have

pressed the Start/Pause button. The estimated time remaining may fluctuate as the

cycle progresses.

The Drying light will illuminate and remain lit until the cycle is complete. When your dryer is

in the cool-down phase, the Cooling light will illuminate. When your dryer is in the wrinkle

prevent phase, the Wrinkle Prevent light will illuminate.

When the cycle is complete, “END” appears in the display panel until you open the dryer

door, press the Power, Close, or Start button, or 5 minutes have passed.

If your dryer is paused during a cycle, the indicator lights will blink until the Start/Pause

button is pressed.

Wrinkle Prevent

Selection Button

Wrinkle Prevent provides approximately 180 minutes of intermittent tumbling in

unheated air at the end of the cycle to reduce wrinkling. Press the Wrinkle Prevent

button to activate this feature.

The indicator light above the pad will illuminate when you select Wrinkle Prevent.

The load is dry and you can remove it at any time during the Wrinkle Prevent cycle.

Dry Level

Selection Button

To select the dry level in the Normal, Heavy Duty, or other Sensor Dry cycles, press the

Dry Level button. An indicator light will illuminate next to the desired dryness level. Press

the button repeatedly to scroll through the settings. Larger or bulkier loads may require

the Very Dry or More Dry setting for complete dryness. Damp Dry is designed to partially

dry items. Use for items that lay flat or hang to dry.

Temp Selection

Button

To select the correct temperature for a load, press the Temp button. An indicator light

will illuminate next to the desired temperature. Press the button repeatedly to scroll

through the settings.

High – For sturdy cottons or those labeled Tumble Dry.

Medium – For permanent press, synthetics, lightweight cottons, or items labeled

Tumble Dry Medium.

Low – For heat sensitive items labeled Tumble Dry Low or Tumble Dry Warm.

Extra Low – Provides the lowest heated dry temperature possible.

Time Selection

Button

When using Manual Dry cycles, you can adjust the time by pressing the Time Selection

button.

During the Sensory Dry cycle, the time light indicator is off because exact drying times

are determined by fluctuating humidity levels.

Adjust Time

You can add time to the automatically set times in the Manual Dry cycles (Time Dry,

Quick Dry).

If you press and hold the Adjust Time button, the time slowly increases until it reaches

the maximum time setting. When you set the time to the maximum, and you briefly

press the button, the time returns to the lowest time setting.

After selecting a preset time using the Time button, you can adjust the time using

the Adjust Time button.

For example, press the Time button to select 40 minutes, and then press the

Adjust Time button to add 5 minutes.

Start/Pause

selection button

Press to pause and restart programs.

Power button

Press once to turn your dryer on. Press again to turn it off. If you turn your dryer on and

do not touch any buttons for 10 minutes, the power automatically turns off.

02 operating Instructions, tips

DV365-03064C-01_EN_20121018.indd Sec5:25DV365-03064C-01_EN_20121018.indd Sec5:25 2012-10-18  8:28:572012-10-18  8:28:57

26_ operating Instructions, tips

CHILD LOCK

Child Lock prevents children from playing with your dryer.

Turning On and Off

To turn Child Lock on or off, press the Temp. and Time buttons simultaneously for 3 seconds.

Child Lock Details:

- You can set Child Lock while your dryer is running.

- Once you turn Child Lock on, no button, except for the Power button, will respond until you

release the Child Lock function.

- The Child Lock indicator will be lit.

If you do not turn Child Lock off before you turn your dryer off, Child Lock will still be on

when you turn your dryer on again. To turn Child Lock off, follow the instructions above.

When other buttons, except for the Power button, do not respond, check the Child Lock

indicator. If Child Lock is on, follow the instructions above to turn Child Lock off.

SOUND OFF

Use this function to mute the button and operating sounds.

Setting and Releasing

To turn the Sound Off function on or off, press the Dry Level and Temp. buttons simultaneously

for 3 seconds.

Sound Off Details:

- You can set Sound Off while your dryer is running.

- Once you have activated Sound Off, the button and operating sounds are muted until you

deactivate it.

- The Sound Off indicator will be lit.

If you do not turn the Sound Off function off before you turn your dryer off, It will still be on

when you turn your dryer on again. To turn Sound Off off, follow the instructions above.

operating Instructions, tips

DV365-03064C-01_EN_20121018.indd Sec5:26DV365-03064C-01_EN_20121018.indd Sec5:26 2012-10-18  8:28:572012-10-18  8:28:57

operating Instructions, tips _27

DRYING RACK (OPTIONAL PART)

Installing and using the drying rack

1. Open the Dryer door.

2. Position the drying rack in the tumbler, placing the front lip of the drying rack on top of the lint

filter.

3. Place the rear legs in the two recessed areas of the dryer’s back wall, and then push down

the middle of the drying rack to fix.

4. Place the items to be dried on the rack, leaving space between them so air can circulate.

5. Close the Dryer door.

6. Use the Time Dry cycle. Select the time according to the moisture and weight of the items.

Start the Dryer. It may be necessary to reset the timer if a longer drying time is needed.

SUGGESTED ITEMS SUGGESTED TEMP. SETTINGS

Washable sweaters

(block to shape and lay flat on rack)

Extra Low

Stuffed toys

(cotton or polyester fiberfilled)

Extra Low

Drying foam rubber, plastic, or rubber on a heat setting may cause damage to the item and

create a fire hazard.

Drying Rack is not supplied in this model. The Drying Rack is optional. You can purchase it

through a service center. (Part code : DC61-01522A)

02 operating Instructions, tips

WARNING

DV365-03064C-01_EN_20121018.indd Sec5:27DV365-03064C-01_EN_20121018.indd Sec5:27 2012-10-18  8:28:572012-10-18  8:28:57

28_ operating Instructions, tips

CLEAN THE LINT FILTER

• After each load.

• To shorten drying time.

• To operate more energy efficiently.

Do not operate your dryer without the lint filter in place.

LOAD THE DRYER PROPERLY

• Place only one washload in your dryer at a time.

• In mixed loads, heavy and lightweight fabrics will dry differently. This may result in lightweight fabrics

being dry while heavy fabrics remain damp at the end of a drying cycle.

• Add one or more additional similar items to your dryer when you are drying only one or two items.

This improves the tumbling action and drying efficiency.

• Overloading restricts tumbling action, resulting in uneven drying as well as excessive wrinkling of some

fabrics.

GETTING STARTED

1. Load your dryer loosely – DO NOT overload.

2. Close the door.

3. Select the appropriate cycle and options for the load (Refer to the “Cycle Chart” section on page 35).

4. Press the Start/Pause button.

5. The dryer indicator light will illuminate.

6. The estimated cycle time will appear in the display.

The time may fluctuate as humidity levels fluctuate in the dryer.

• When the cycle is complete, “End” will appear in the display.

• Pressing Power cancels the cycle and stops your dryer.

• The Drying, Cooling, and Done indicator lights will illuminate during those portions of the cycle.

Do not place anything on top of your dryer while it is running.

operating Instructions, tips

WARNING

DV365-03064C-01_EN_20121018.indd Sec5:28DV365-03064C-01_EN_20121018.indd Sec5:28 2012-10-18  8:28:572012-10-18  8:28:57

care and cleaning _29

care and cleaning

CONTROL PANEL

Clean with a soft, damp cloth. Do not use abrasive substances.

Do not spray cleaners directly on the panel.

The control panel finish may be damaged by some laundry pre-treatment soil and stain remover products.

Apply such products away from your Dryer and wipe up any spills or overspray immediately.

TUMBLER

Remove any stains such as crayon, ink, or fabric dye (from new items such as towels or jeans) with an all-

purpose cleaner.

Tumble old towels or rags to remove any excess stain or cleaning substance.

Once these steps are followed, stains may still be visible, but should not transfer to subsequent loads.

POWDER COATED TUMBLER

To clean the powder coated tumbler, use a damp cloth with a mild, non-abrasive cleaner suitable for

powder coated surfaces.

Remove the cleaner residue and dry with a clean cloth.

DRYER EXTERIOR

The entire dryer has a high-gloss finish. Clean with a soft, damp cloth. Do not use abrasive substances.

Protect the surface from sharp objects as they may scratch or damage the finish. Do not place any heavy

or sharp objects or a detergent box on the dryer. Keep them on the purchased pedestal or in a separate

storage box.

DRYER EXHAUST SYSTEM

Inspect and clean the dryer exhaust system yearly to maintain optimum performance.

The outside exhaust hood should be cleaned more frequently to ensure proper operation.

03 care and cleaning

DV365-03064C-01_EN_20121018.indd Sec4:29DV365-03064C-01_EN_20121018.indd Sec4:29 2012-10-18  8:28:582012-10-18  8:28:58

30_ special laundry tips

special laundry tips

SPECIAL LAUNDRY TIPS

Please follow the care label or manufacturer’s instructions for drying special

items. If care label instructions are not available, use the following information as

a guide.

Bedspreads & Comforters

• Follow the care label instructions or dry using the Normal cycle with

the temperature set to High.

• Make sure the item is thoroughly dry before using or storing.

• May require repositioning to ensure even drying.

Blankets

• Use the Normal cycle and dry only one blanket at a time for best

tumbling action.

• Make sure the blanket is thoroughly dry before using or storing.

Curtains & Draperies

• Use the Perm Press cycle and the Low or Extra Low temperature

setting o help minimize wrinkling.

• Dry in small loads for best results and remove as soon as possible.

Cloth Diapers

• Use the Normal cycle and the High temperature setting for soft,

fluffy diapers.

Down–filled Items (jackets,

sleeping bags, comforters,

etc.)

• Use the Normal cycle and the Low or Extra Low temperature setting.

• Adding a couple of dry towels shortens drying time and absorbs

moisture.

Pillows

• Use the Normal cycle.

• Add a couple of dry towels to help the tumbling action and to fluff the

item.

• DO NOT dry kapok or foam pillows in the dryer.

Plastics (shower curtains,

outdoor furniture covers,

etc.)

• Use the Time Dry cycle and the Low or Extra Low temperature

settings depending on the care label instructions.

THINGS TO AVOID :

• Fiberglass items (curtains, draperies, etc.).

• Woolens, unless recommended on the label.

• Vegetable or cooking oil-soaked items.

• Foam Rubber (rug backs, stuffed toys, shoulder pads, etc.)

DV365-03064C-01_EN_20121018.indd Sec6:30DV365-03064C-01_EN_20121018.indd Sec6:30 2012-10-18  8:28:582012-10-18  8:28:58

troubleshooting _31

troubleshooting

CHECK THESE POINTERS IF YOUR DRYER…

PROBLEM SOLUTION

Doesn’t run.

• Be sure the door is latched shut.

• Be sure the power cord is plugged into a live electrical outlet.

• Check your home’s circuit breakers or fuses.

•

Press the Start/Pause button again if the door is opened during the cycle.

Doesn’t heat.

• Check your home’s circuit breakers or fuses.

• On a gas dryer, see if the gas supply is on.

• Clean the lint filter and exhaust duct.

• See if the Dryer has moved into the cool-down phase of the cycle.

Doesn’t dry.

• Check all of the above, plus...

•

Be sure the exhaust hood outside your home can open and close freely.

• Check exhaust system for lint buildup. Ducting should be inspected

and cleaned annually.

• Use a 4” rigid metal exhaust duct.

• Do not overload. 1 wash load = 1 dryer load.

• Sort heavy items from lightweight items.

• Large, bulky items like blankets or comforters may require

repositioning to ensure even drying.

• Check that the washer is draining properly to extract adequate water

from the load.

• The load may be too small to tumble properly. Add a few towels.

Is noisy.

• Check the load for objects such as coins, loose buttons, nails, etc.

Remove promptly.

• It is normal to hear the dryer gas valve or heating element cycle on

and off during the drying cycle.

• Be sure the Dryer is leveled properly as outlined in the installation

instruction.

• It is normal for the Dryer to hum due to the high volume of air moving

through the dryer drum and exhaust system.

Dries unevenly.

• Seams, pockets, and other similarly heavy areas may not be

completely dry when the rest of the load has reached the selected

dryness level. This is normal. Select the More Dry setting if desired.

• If one heavy item is dried with a lightweight load, such as one towel

with sheets, it is possible that the heavy item will not be completely

dry when the rest of the load has reached the selected dryness level.

Sort heavy items from lightweight items for best drying results.

Has an odor.

• Household odors from paint, varnish, strong cleaners, etc. may enter

the dryer with the surrounding room air. This is normal as the Dryer

draws the air from the room, heats it, pulls it through the tumbler, and

exhausts it outside.

• When these odors linger in the air, ventilate the room completely

before using the Dryer.

Shuts off before load is dry

• The dryer load is too small. Add more items or a few towels and

restart the cycle.

• The dryer load is too large. Remove some items and restart the dryer.

05 troubleshooting

DV365-03064C-01_EN_20121018.indd Sec7:31DV365-03064C-01_EN_20121018.indd Sec7:31 2012-10-18  8:28:582012-10-18  8:28:58

32_ troubleshooting

Lint on clothes

• Make sure the lint filter is cleaned before every load. With some loads

that produce high amounts of lint, it may be necessary to clean the

filter during the cycle.

• Some fabrics are lint producers (for example, a fuzzy white cotton

towel) and they should be dried separately from clothes that are lint

trappers(for example, a pair of black linen pants).

• Divide larger loads into smaller loads for drying.

• Check pockets thoroughly before washing and drying clothes.

Garments still wrinkled after

Wrinkle-Away

• Small loads of 1 to 4 items work best.

• Load fewer garments.

• Load similar-type garments.

Odors remain in clothing

after Refresh.

• Fabrics having strong odors should be washed in a normal cycle.

Water drips from the nozzle

when Steam-Care starts

• This is steam condensation. The dripping water will stop after a short

time.

Sprayed water is not visible

during Steam-Care

• Sprayed water is difficult to see when the door is closed.

INFORMATION CODES

Information codes may be displayed to help you better understand what is occurring with your Dryer.

ERROR DISPLAY MEANING SOLUTION

Clogged Lint Screen

Vent is restricted

Clean the screen or vent.

If the problem continues, call for service.

Invalid heating Temp when the dryer

is running.

Call for service.

Running the dryer with door open

Close the door and then restart.

If the problem continues, call for service.

Door is not closing properly Call for service.

bE2

Unit detects a button is being

pressed for over 30 secs or button is

stuck

Make sure a button is NOT being pressed

continuously. Try restarting the cycle.

If the problem continues, call for service.

Invalid power source frequency

Try restarting the cycle.

If the problem continues, call for service.

EEPROM is not communicating

properly

Try restarting the cycle.

If the problem continues call for service.

For any codes not listed above, call 1–800–726–7864 (1–800–SAMSUNG)

troubleshooting

DV365-03064C-01_EN_20121018.indd Sec7:32DV365-03064C-01_EN_20121018.indd Sec7:32 2012-10-18  8:28:582012-10-18  8:28:58

appendix _33

appendix

FABRIC CARE CHART

The following symbols provide garment care direction. The Clothing care labels include symbols for

washing, bleaching, drying and ironing, or dry cleaning when necessary. The use of symbols ensures

consistency among garment manufacturers of domestic and imported items. Follow care label directions to

maximize garment life and reduce laundering problems.

Wash Cycle Special Instructions

Warning Symbols for

Laundering

Normal Line Dry/ Hang to Dry Do Not Wash

Permanent Press /

Wrinkle Resistant /

Wrinkle Control

Drip Dry Do Not Wring

Gentle/Delicates Dry Flat Do Not Bleach

Hand Wash

Heat Setting

Do Not Tumble Dry

Water Temperature**

High

No Steam (added to

iron)

Hot Medium Do Not Iron

Warm Low

Dryclean

Cold Any Heat Dry Clean

Bleach

No Heat/Air Do Not Dry Clean

Any Bleach (when

needed)

Iron-Dry or Steam

Temperatures

Line Dry/ Hang to Dry

Only Non-Chlorine

(color-safe)

Bleach (when needed)

High Drip Dry

Tumble Dry Cycle Medium Dry Flat

Normal

Low

Permanent Press/

Wrinkle Resistant/

Wrinkle Control

Gentle/ Delicates

** The dot symbols represent appropriate wash water temperatures for various items. The temperature

range for Hot is 105° –125 °F / 41° – 52 °C, for Warm 85° – 105 °F / 29° – 41 °C and for Cold 60° – 85 °F

/ 16° – 29 °C. (Wash water temperature must be a minimum of 60 °F / 16 °C for detergent activation and

effective cleaning.)

06 appendix

DV365-03064C-01_EN_20121018.indd Sec8:33DV365-03064C-01_EN_20121018.indd Sec8:33 2012-10-18  8:28:582012-10-18  8:28:58

34_ appendix

PROTECTING THE ENVIRONMENT

This appliance is manufactured from recyclable materials. If you decide to dispose of this appliance,

please observe local waste disposal regulations. Cut off the power cord so that the appliance cannot be

connected to a power source. Remove the door so that animals and small children cannot get trapped

inside the appliance.

DECLARATION OF CONFORMITY

This appliance complies with UL2158.

SPECIFICATIONS

TYPE FRONT LOADING DRYER

DIMENSIONS

Div Inches (cm) Div Inches (cm)

A. Height

38.3” (97.4)

C. Depth with

door open 90°

49” (124.5)

B. Width

27” (68.6)

D. Depth

31.1” (79.0)

WEIGHT

119.0 lb (54.0 kg)

HEATER RATING

5300 W

appendix

DV365-03064C-01_EN_20121018.indd Sec8:34DV365-03064C-01_EN_20121018.indd Sec8:34 2012-10-18  8:28:582012-10-18  8:28:58

appendix _35

CYCLE CHART

( : factory setting,  : selectable)

Cycle Recommended Item Max Load Size

Functions

Sensor Dry Level

Sensor Dry

Normal Cottons, Work clothes, Linen, Mixed Loads

Normal dry

Heavy Duty

Heavy Fabrics such as jean, corduroys,

heavy work clothes

Normal dry

Perm Press

Shirts, Synthetic Fabrics, Knits, Wrinkle-free

cottons, Permanent

Normal dry

Delicates Underwear, Blouses, Lingerie

Normal dry

Sanitize Bedding, Curtains, Children` clothing

Very dry

(No change)

Manual Dry

Time Dry Any load

Quick Dry Small loads

Steam Cycles

Wrinkle Away Shirts, Trouser, Blouses

Refresh Shirts, Trouser, Comforter, Pillows

Cycle

Functions Options

Temp Control

Time

Wrinkle

Prevent

High Medium Low Extra Low

Sensor Dry

Normal



---



Heavy Duty



----



Perm Press -



---



Delicates - - -



Sanitize



----



Manual Dry

Time Dry





Quick Dry



---



Steam Cycles

Wrinkle Away



---



Refresh



----



Load Size Recommendations

Large load : Fill the drum to about ¾ full. Do not add items over this level as they need to tumble

freely.

Medium load : Fill the drum to about ½ full.

Small load : Fill the drum with 3~5 items, not more than ¼ full.

* For best results, follow the load size recommendations for each dry cycle.

06 appendix

DV365-03064C-01_EN_20121018.indd Sec8:35DV365-03064C-01_EN_20121018.indd Sec8:35 2012-10-18  8:28:582012-10-18  8:28:58

36_ warranty

warranty (U.S.A)

SAMSUNG DRYER

LIMITED WARRANTY TO ORIGINAL PURCHASER

This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS AMERICA, INC.

(SAMSUNG) and delivered new, in the original carton to the original consumer purchaser, is warranted by

SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of:

One (1) Year All Parts and Labor

Two (2) Years Control Board Parts

This limited warranty begins on the original date of purchase, and is valid only on products purchased and

used in the United States.

To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service

procedures.

Warranty service can only be performed by a SAMSUNG authorized service center.

The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or

SAMSUNG’s authorized service center.

SAMSUNG will provide in-home service during the warranty period at no charge, subject to availability

within the contiguous United States.

In-home service is not available in all areas.

To receive in-home service, product must be unobstructed and accessible to the service agent.

If service is not available, SAMSUNG may elect to provide transportation of the product to and from an

authorized service center.

SAMSUNG will repair, replace, or refund this product at our option and at no charge as stipulated herein,

with new or reconditioned parts or products if found to be defective during the limited warranty period

speciﬁ ed above.

All replaced parts and products become the property of SAMSUNG and must be returned to SAMSUNG.

Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is

longer.

This limited warranty covers manufacturing defects in materials and workmanship encountered in normal,

noncommercial use of this product and shall not apply to the following: damage that occurs in shipment;

delivery and installation; applications and uses for which this product was not intended; altered product or

serial numbers; cosmetic damage or exterior ﬁ nish; accidents, abuse, neglect, ﬁ re, water, lightning, or other

acts of nature or God; use of products, equipment, systems, utilities, services, parts, supplies, accessories,

applications, installations, repairs, external wiring or connectors not supplied or authorized by SAMSUNG

that damage this product or result in service problems; incorrect electrical line voltage, ﬂ uctuations and

surges; customer adjustments and failure to follow operating instructions, maintenance and environmental

instructions that are covered and prescribed in the instruction book; product removal and reinstallation;

problems caused by pest infestations.

This limited warranty does not cover problems resulting from incorrect electric current, voltage or supply,

light bulbs, house fuses, house wiring, cost of a service call for instructions, or ﬁ xing installation errors.

SAMSUNG does not warrant uninterrupted or error-free operation of the product.

DV365-03064C-01_EN_20121018.indd Sec10:36DV365-03064C-01_EN_20121018.indd Sec10:36 2012-10-18  8:28:592012-10-18  8:28:59

warranty _37

Except as set forth herein, there are no warranties on this product either express or implied, and samsung

disclaims all warranties including, but not limited to, any implied warranties of merchantability, infringement

or ﬁ tness for a particular purpose.

No warranty or guarantee given by any person, ﬁ rm, or corporation with respect to this product shall be

binding on samsung.

Samsung shall not be liable for loss of revenue or proﬁ ts, failure to realize savings or thter beneﬁ ts, or any

other special, incidental or consequential damages caused by the use, misuse, or inability to use this

product, regardless of the legal theory on which the claim is based, and even if samsung has been advised

of the possibility of such damages.

Nor shall recovery of any kind against samsung be greater in amount than the purchase price of the product

sold by samsung and causing the alleged damage.

Without limiting the foregoing, purchaser assumes all risk and liability for loss, damage, or injury to

purchaser and purchaser’s property and to others and their property arising out of the use, misuse,

or inability to use this product. This limited warranty shall not extend to anyone other than the original

purchaser of this product, is nontransferable and states your exclusive remedy.

Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation

of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This

warranty gives you speciﬁ c rights, and you may also have other rights, which vary from state to state.

To obtain warranty service, please contact SAMSUNG at:

Samsung Electronics America, Inc.

85 Challenger Road Ridgeﬁ eld Park, NJ 07660

1-800-SAMSUNG (726-7864)

www.samsung.com

DV365-03064C-01_EN_20121018.indd Sec10:37DV365-03064C-01_EN_20121018.indd Sec10:37 2012-10-18  8:28:592012-10-18  8:28:59

38_ warranty

warranty (CANADA)

SAMSUNG DRYER

LIMITED WARRANTY TO ORIGINAL PURCHASER

This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS CANADA, INC.

(SAMSUNG) and delivered new, in the original carton to the original consumer purchaser, is warranted by

SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of:

One (1) year part and labor

This limited warranty begins on the original date of purchase, and is valid only on products purchased and

used in the Canada.

To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service

procedures.

Warranty service can only be performed by a SAMSUNG authorized service center.

The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or

SAMSUNG’s authorized service center.

SAMSUNG will provide in-home service during the warranty period at no charge, subject to availability

within the Canada.