WiMo 17754.04 4m Band Moxon Antenne Instrucciones de operación

Marca
WiMo
Modelo
17754.04 4m Band Moxon Antenne
Tipo
Instrucciones de operación
70MOX
70MOX
0,62m
1,665m
Peso: 1,8Kg.
Max. Potencia: 10,0 kW
yagi antenna
yagi antenna
Rev. v1.4 - 01/04/2021
Artikel nr: 17754.04
Thank you for choosing EAntenna.
All our products are manufactured and developed with the best materials on the market, to offer the best qualities and
guarantees to our customers.
The Yagi type MOXON antennas were developed by Leslie A. Moxon, to be used in communications in HF during the 2nd half
of the 20th century, quite successfully. Its cost, profit and ease of construction make it an option very convenient. As it is a
specific antenna according to the bands in which we want to operate. The address of the maximum Gain is obtained in the
opposite direction to the reflector and perpendicular to the radiating element. According to the position with respect to
ground, horizontal or vertical, will be its polarization. It is very important that this coincides with the polarization used in the
antenna of the equipment to which you connect with this antenna.
Like any antenna manufactured by EAntenna, we do not include a connector, to have the minimum losses. We include
terminals to solder directly, although we offer as an option balun or ferrites EMI / RFI.
We detail the materials used, for their best use and assembly. All the fittings are made of stainless steel and the
Aluminum is made of T6061 or T6063 alloy, known as Aeronautical Aluminium, which offers the best conditions to withstand
the most extreme climates, the force of the wind and the best conductivity. The plastics used, is Polyamide or Polypropylene,
which offer the best hardness and durability for the passage of time. We offer guarantee in the operation, and guarantee in the
ironworks, delivering the kit of hardware some extra pieces, for possible losses or forced breakages.
In the following pages we detail the exploded view with its graphics.
SPECIFICATIONS
Eantenna 70MOX
Elements:
2
Frequency Range:
70.0 ~ 70.5 MHz
Gain:
6,05dBi
F/B:
38,5 dB
Bandwidth:
500 KHz.
SWR:
1,0:1~1,2:1
Impedance
50 Ohms
Max. Power:
10 kW.
Max. Element Length:
1,67m. / 65,7"
Boom Length:
0,61m. / 24"
Wind Survival
200 kmh / 120 mph
Weight:
1,8 Kg. / 4 Pounds
14,0.......21,0 MHz.
1
1
1.3
1.3
1.5
1.5
2.0
2.0
3.0
3.0
5.0
5.0
3500 KHz.
3500 KHz.
3800 KHz.
3800 KHz.
Ω
300 W.
Boom size: 30x30x2mm
Element Diameter: 13x1mm ~ 10x1mm
620mm
1665mm
66,0mm
Alimentación/FeedAlimentación/Feed
Vivo
Inner Conductor
Malla
Outter Conductor
COAXIAL
Vivo
Inner Conductor
COAXIAL
Reflector
Driven
Dirección directividad
Beam Direction
ESPAÑOL
13mm Ø 10mm Ø
66mm
ABRAZADERA 8-12mm Ø
Las medidas de la pagina anterior están expresadas en medidas exteriores, o sea, midiendo desde cada extremo del tubo. Una vez que los
elementos horizontales estén ensamblados correctamente, se procede a formar el rectángulo con las medidas facilitadas en las pagina 2.
Tener en cuenta la posición de los extremos según la pagina 6, para tener en cuenta el reflector y el driven que no se coloquen de la forma inco-
rrecta. Para fijar el elemento al boom, posicione el plástico de 13mm (EAHYP013) en las posiciones donde corresponde, y se fijan con los tornillos
DIN 912 M6X40.
La fijación de cada elemento con la parte curva es mediante la abrazadera Sin/Fin 8-16mm (P0100022)
La medida de ajuste está justamente debajo. Esta medida es desde final del tubo de 13mm al extremo de la curva.
ELEMENTO DRIVEN
Placas 6m
DIN 912 6x40mm
DIN 912 6x20mm
DIN 9021 M6
DIN 985 M6
Para colocar cada placa al boom, se fija mediante los tornillos DIN 912 M6X20 y arandela DIN 9021 M6. Esta placa debe de quedar bien firme
para la colocación del elemento. El paso siguiente seria igual que los demás elementos, pero teniendo en cuenta que los tornillos que
utilizaremos son DIN 912 M6X40 y tuercas autoblocante DIN 985 M6 una vez que esté ensamblada toda la antena.
ENGLISH
13mm Ø 10mm Ø
66mm
The measures of the previous page are expressed in external dimensions, ie, measuring from each end of the tube. Once the horizontal
elements are assembled correctly, proceed to form a rectangle with the measures provided below.
Take into account the position of the ends according to page 6, to take account of the reflector and drivendo not reverse.
To set the reflector to boom, position the plastic clamps of 13mm (EAHYP013) in positions where it belongs, and fixed with screws
DIN 912 M6x40.
The final lenght is the pre-sintonized. The lenght is from the end of the 13mm tube to the outside of the bend tube.
DRIVEN ELEMENT
The fixing of the LOOP element, each element is using a Hose Clamp 8-12mm (P0100022) the 13 to 10mm diameter.
HOSE CLAMP 8-12mm Ø
(P01000022)
Placas 6m
DIN 912 6x40mm
DIN 912 6x20mm
DIN 9021 M6
DIN 985 M6
To place the plate to the boom, use screws DIN 912 M6X20 and DIN 9021 M6 washer. This plate must be very firm for positioning the
element. Next step is similar to reflector mounting, use again DIN 912 M6x40 and Din 985 M6slft locking nuts once it is all assembled
antenna.
PLACAS SUJECIÓN MÁSTIL ESPAÑOL
La placa de sujeción BOOM/MÁSTIL (EA013018) de 100X100X6mm consta de 8 agujeros; 4 gruesos para los abarcones redondos y 4
para los abarcones cuadrados que sujetan el BOOM.
Los 4 agujeros de mayor grosor tienen la función de que hagan la mayor fuerza sobre el mástil, mediante abarcones redondos de M8.
Los abarcones redondos de M8 (A-0163), van fijados mediante arandela DIN 9021 M8 y tuerca DIN 934 M8 proporcionadas en el mismo
abarcón, y fijada al mástil con la Mordaza (23035.50).
Detallamos dibujos para una mayor ilustración:
Vista lateral desde el mástil Vista laterall desde el BOOM
Front view from Mast
Front view from BOOM
(23035.50) (A-0163)
(P0500030) (S934-96)
(S9021-96)
(EA013018) (EA013018)
The clamping plate BOOM / MAST (EA013018) 100X100X6mm consists of 8 holes; 4 thick for round U-bolts and 4 square U-bolts for
securing the BOOM.
The 4 holes are function that make the greatest force on the mast by means of M8 round U-bolts. Round U-bolts M8 (A-0163), are
secured by washer DIN 9021 M8 and nut DIN 934 M8 provided in the same bag, and fixed to the mast with clamp (23035.50).
Detailed drawings for further illustration:
(EA013018) (EA013018)
(23035.50) (A-0163)
(P0500030) (S934-96)
(S9021-96)
MAST TO BOOM PLATE ASSEMBLY
Front view from Mast
Side view from Mast
Front view from BOOM
Side view from BOOM
ENGLISH
Montaje correcto:
Dirección directividad
Beam Direction
Reflector
Driven
BOOM
COAXIAL
Vivo
Inner Conductor
Malla
Outter Conductor
COAXIAL
Alimentación mediante coaxial:
Después de varios ensayos, vemos que el balun de aluminio hace peor trabajo que un choque de coaxial.
Por esto, recomendamos hacer a escaso centímetros o metros de la alimentación, un choque del coaxial de bajada de 4
vueltas de 8 centímetros de diámetro y así el retorno de RF será mínimo o nulo.
En el dibujo aconsejamos que siempre el choque se haga por debajo de los elementos para que el coaxial no haga intera-
ccion con los elementos.
Boom DRVREF
ESPAÑOL
!Hagalo lo mas corto posible!
Montaje correcto:
Dirección directividad
Beam Direction
Reflector
Driven
ENGLISH
BOOM
COAXIAL
Vivo
Inner Conductor
Malla
Outter Conductor
COAXIAL
Boom DRVREF
Keep the splice as short as possible !
Coax cable feeding:
After several trials, we see that the balun aluminum makes it worse job than a coaxial choke. For this, we recommend 5 turns
of 8 cm and thus the RF return will be minimal or absent.
The below drawing advise you how to do the clash below the boom to avoid interaction with the elements.
PART #
PIEZA Nº
IMAGEN
PART IMAGE
DESCRIPCION
DESCRIPTION
MEDIDAS
SIZES
CANTIDAD
QUANTITY
EA013018
Placa Mástil/Boom
Mast and Boom plate
100 x 100 x 6mm
PACKING LIST
LISTA DE PIEZAS BOLSA 1 - BAG #1
Mordaza
Tube Clamp
Abarcon Cuadrado
Square Clamp
DIN 9021
DIN 934
50mm, M8
30mm
M6
M6
2
2
4
4
1
2
23035.50
P0500030
A-0163
S9021-96
S934-96
Llave Allen
Llave Fija
5mm
M10
1
1
P1300001
P1300003
ENGLISHESPAÑOL
DIN 127 WASHER
DIN 934 NUT
M8
M8 4
4
S934-98
S127-98
Abarcon
U-Bolt.
50mm
PART #
PIEZA Nº
IMAGEN
PART IMAGE
DESCRIPCION
DESCRIPTION
CANTIDAD
QUANTITY
BOOM 612mm x 30mm 1
1
1
2
70MOX
A-A
PACKING LIST
LISTA DE PIEZAS
Sección Tubo 10mm
10mm Tube section
13mm REFLECTOR
13mm DRIVEN
570mm x 10mm Ø
1530mm x 13mm Ø
1530mm x 13mm Ø
. .
PART #
PIEZA Nº
IMAGEN
PART IMAGE
DESCRIPCION
DESCRIPTION
CANTIDAD
QUANTITY
BOLSA 2 - BAG #2
DIN 9021 M6 2
S9021-96
Tornillo Allen DIN 912
Allen DIN 912 Screw M6x20mm 2
S912-9620
Placa para Elementos
Elements plates 150x50x6mm 1
EA010026
Plásticos
Plastic Blocks 13mm Ø 3
EAHYP013
Tornillo Allen DIN 912
Allen DIN 912 Screw M6x40mm 6
S912-9640
Abrazadera Sin-Fin
Hose clamp 4
P0100022
M6
8-12mm
6
S985-906 Tuerca Autoblocante DIN 985
DIN 985 NUT
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

WiMo 17754.04 4m Band Moxon Antenne Instrucciones de operación

Marca
WiMo
Modelo
17754.04 4m Band Moxon Antenne
Tipo
Instrucciones de operación
Descargar PDF
informe

En otros idiomas

Documentos relacionados

Otros documentos