Avanti GR2013CSS Manual de usuario

Marca: Avanti

Modelo: GR2013CSS

Categoría: Dispensador de agua

Tipo: Manual de usuario

INSTRUCTION MANUAL

MANUAL DE INSTRUCCIONES

Model Number/Número de Modelo

WD362BP

WD363P

CAUTION:

BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING

INSTRUCTIONS.

Avanti has a policy of continuous improvement on its products and reserves the right to change materials and specifications

without notice.

La sección en español empieza en la página 14

Avanti Products

P.O. Box 520604 - Miami, Florida 33152

www.avantiproducts.com

TABLE OF CONTENTS

Help Us Help you 4

Parts and Features 5

Important Safety Instructions 6

Electrical Connection 6

Installation Guidelines 6

Height Adjustment Platform 7 – 8

Operation Instructions 9

Before Using Your Water Dispenser 9

Operating Your Water Dispenser 10

Replacing the Water Bottle 10

Cold Water Control 10

Hot Water Control 10

Child Safety Guard (Hot Water Faucet) 10

Cup Dispenser (Optional) 10

Care and Maintenance 11

Taking the dispenser out of service 11

Problems with Your Water Dispenser 11

Troubleshooting Guide 11

Service for Your Water Dispenser 12

Wiring Diagram 12

Your Avanti Products Warranty 13

Instrucciones en Español 14 – 17

Registration Information and Registration Card 19

HELP US HELP YOU...

Read this guide carefully.

It is intended to help you operate and maintain

your new water dispenser properly.

Keep it handy to answer your questions.

If you don't understand something or you need

more help, please call:

Avanti Customer Service

800-220-5570

Keep proof of original purchase date (such as

your sales slip) with this guide to establish the

warranty period.

Write down the model and serial numbers.

You'll find them on a label located on the back

side of the unit.

Please write these numbers here:

____________________________________

Date of Purchase

____________________________________

Model Number

____________________________________

Serial Number

Use these numbers in any correspondence or

service calls concerning your water dispenser.

If you received a damaged water dispenser,

immediately contact the dealer (or builder) that

sold you the water dispenser.

Save time and money. Before you call for

service, check the Problem Solver Guide. It

lists causes of minor operating problems that

you can correct yourself.

IF YOU NEED SERVICE

We're proud of our service and want you to be

pleased. If for some reason you are not happy

with the service you receive, here are some

steps to follow for further help.

FIRST, contact the people who serviced your

appliance. Explain why you are not pleased. In

most cases, this will solve the problem.

NEXT, if you are still not pleased, write all the

details, including your telephone number, and

send to:

Customer Service

Avanti Products

10880 NW 30 Street

Miami, FL 33172

PARTS AND FEATURES

HEIGHT ADJUSTMENT PLATFORM

1. WATER INTAKE

2. HOT WATER LIGHT (RED)

3. POWER INDICATOR (YELLOW)

4. COLD INDICATOR LIGHT (GREEN)

5. HOT WATER FAUCET (PINK)

6. COLD WATER FAUCET (GREY)

7. REMOVABLE DRIP TRAY

8. ADJUSTABLE FOOT

9. COOLING SWITCH

10. HEATING SWITCH

11. CONDENSER COIL

12. POWER SUPPLY CORD

13. WATER DRAIN

Important Safety Instructions

 WARNING

To reduce the risk of burns, fire, electrical

shock, or injury when using your appliance,

follow these basic precautions:

 Read all instructions before using the water dispenser.

 Never clean parts with flammable fluids. The fumes can create a fire hazard or

explosion.

 Do not store or use gasoline or any other flammable vapors and liquids in the vicinity

of this or any other water dispenser. The fumes can create a fire hazard or

explosion

 Do not plug unit into receptacle until you ensure the water tank switches are off.

-Save these instructions-

 Electrical Connection

This appliance should be properly grounded for your safety. The power cord of this appliance is

equipped with a three-prong plug which mates with standard three prong wall outlets to minimize the

possibility of electrical shock.

Plug the appliance into an exclusive properly installed-grounded wall outlet. Do not under any

circumstances cut or remove the third (ground) prong from the power cord. Any questions concerning

power and or grounding should be directed toward a certified electrician or an authorized Avanti

Products service center.

This appliance requires a standard 115/120-volt 60Hz electrical outlet with three-prong ground.

The cord should be secured behind the appliance and not left exposed or dangling to prevent

accidental injury.

Do not use an adapter plug with this appliance.

Do not use an extension cord with this appliance. If the power cord is too short, have a qualified

electrician or service technician install an outlet near the appliance.

INSTALLATION GUIDELINES:

 Remove the exterior and interior packing.

 Place your appliance on a floor that is strong enough to support the dispenser when it is fully

loaded. If it does not sit level on the floor, adjust the front right foot to level the unit well to the

floor. Note: Only the front right foot is adjustable.

 Locate the appliance away from direct sunlight and sources of heat (stove, heater, radiator,

etc.). Direct sunlight may affect the acrylic coating and heat sources may increase electrical

consumption. Extreme cold ambient temperatures may also cause the appliance not to

perform properly.

 Allow 2 inches of space between the water dispenser and the wall, which allows for proper air

circulation to cool the compressor.

 Plug the appliance into an exclusive properly installed-grounded wall outlet. Do not cut or

remove the third (ground) prong from the power cord under any circumstances. Any

questions concerning power and/or grounding should be directed toward a certified

electrician or an authorized Avanti Products service center.

 This water dispenser is not recommended for outdoor use.

 Do not locate the dispenser in area where the temperature may fall below freezing (32

º F).

 Keep area around dispenser free of dust and dirt.

 Keep the reserve supply of water bottles away from excessive heat and light.

 Never unplug the water cooler, except for maintenance.

Height Adjustment Platform

 To make the water dispenser faucets more accessible your unit has been supplied with a

height adjustment platform. The platform requires assembly as shown below.

Parts Provided:

1 Front Panel

1 Back Panel

1 Stability Ring (located on the top foam cover)

2 Short Screws and 2 Long Self-tapping Screws (located in the bag with instruction manual)

Remove all parts from the box and remove the packing materials.

a) Align both the front and back panels of the platform and assemble as shown in

figure 1.

Fig. 1

b) Align the assembled platform to the bottom stability ring as shown in figure 2a.

Align the areas marked “1” and “2” on the platform with same areas marked “1”

and “2” on the stability ring.

(NOTE: These areas must be aligned correctly for the unit to be assembled. If the

platform is not aligned correctly to the stability ring, the retaining clips could be

permanently damaged and cause the platform to be unstable).

Fig 2a

Front Panel

Back Panel

Bottom Ring

c) Be sure that both the clips on each side of the platform and the screw holes align

correctly before inserting the clips in their respective slots on the stability ring as

shown in Fig 2b.

Fig 2b

d) Once you have assembled both the platform and stability ring together, using the

screws (2 short) provided firmly secure the stability ring to the platform as shown

in Fig 2b and Fig 2c.

(insert figure 2c.)

e) Place the water dispenser on the assembled platform and firmly secure the water

dispenser and platform together using the screws provided (2 long self-tapping).

Be sure the power cord fits securely over the cutout in the back panel.

Clip slot on

the ring

Clip foot on

the ring

Recessed screw

hole on the

bottom ring

Fixing screw

stud on the

back piece

OPERATION INSTRUCTIONS

Before Using Your Water Dispenser

 Check to be sure the following parts are included:

 Instruction manual

 4 extra cup dispenser cabinet plugs

 Accessories order form.

 1 height adjustment platform assembly (2 panels, 1 stability ring, 4 screws)

 Before connecting the appliance to the power source, let it stand upright for approximately 2

hours. This will reduce the possibility of a malfunction in the cooling system from handling

during transportation.

 The water dispenser is pre-cleaned at the factory but the reservoir and water lines

must be flushed with fresh water before use as follows:

 Keep the unit unplugged.

 Fill water tank with tap water full to capacity (more than 3/4 of a gallon). Wait for 5

minutes until water settles.

 Press the hot water faucet until water comes out, then stop.

 Plug the dispenser into the electrical outlet. Both heating and cooling indicator lights

on front will light up at first. We are ready to complete the first cycle. In order to do

that, wait for the hot water indicator light to go off first (approximately 10 minutes),

then wait for the cold water indicator light to go off (another 40 minutes,

approximately).

 Unplug the dispenser from the electrical outlet. Proceed to drain the water from the

faucets one at a time until no more water remains.

(Note: To facilitate this operation, use a large container).

 Then, drain any water left in the tanks by opening the drain plug located on the back,

until it drains completely.

 Proceed to close the drain cap.

 Place the 5-gallon bottle of water on the water intake, allow water to stand for

approximately one minute.

 Open water faucets to insure water flows from both faucets.

 Plug dispenser into the electrical outlet.

 Now you are ready to use your water dispenser.

NOTE: Your water dispenser has been cleaned and sanitized before leaving the

factory, but in case a taste problem develops, place two tablespoons of

baking soda and add tap water. Fill water tank again and repeat basic

operations previously outlined, except turn the switch marked HOT “OFF” to

avoid leaving residues in hot water tank.

ATTENTION:

If you do not plan to use the water heating function for more than three days, we

recommend that you turn the HOT switch to the “OFF” position.

WARNING

IMPROPER USE OF THE GROUNDED PLUG CAN RESULT IN THE RISK OF ELECTRICAL SHOCK. IF

THE POWER CORD IS DAMAGED, HAVE IT REPLACED BY AN AUTHORIZED AVANTI PRODUCTS

SERVICE CENTER.

OPERATING YOUR WATER DISPENSER

 Steps to replace water bottles

 Use a clean cloth to wipe off neck of bottle.

 Remove cap.

 Carefully lift bottle (approx. 40 lbs.) using your legs and not your back. Do not place hands on

opening of bottle while placing in reservoir.

 Insert the water bottle on the water intake over reservoir opening so it settles properly on it.

 Wipe off any water which may have splashed on dispenser top.

 When a new bottle is installed you must open the hot water faucet and remove no less than 4 full

cups of water to insure the water flows properly and the water reservoir is at the proper level.

 Cold Water Control

Turn the cooling switch on. The green indicator will be lit on and the process begins. When the water

reaches the right temperature the green light goes off automatically.

 Hot Water Control

Turn the heating switch on, the red indicator will be lit on and the heating process starts. When the

water reaches the right temperature the red light goes off automatically. When the temperature goes

down to approx. 80º C (176º F), the red indicator will glow again and another heating process starts.

To dispense hot water:

 Slide red safety button to the left and hold while pressing downward on hot water faucet to

dispense hot water.

 Safety button will return to its original position when faucet is released.

Cup Dispenser (Optional)

A cup dispenser may be installed by using the mounting holes (covered with plastic caps) located

near the top of the right side panel of the cooler. The cup dispenser comes equipped with a mounting

bracket and screws and may be ordered by completing the enclosed order form provided with your

instruction manual.

NOTE:

THE HOT WATER FAUCET HAS A CHILD-SAFETY GUARD ATTACHMENT.

CARE AND MAINTENANCE

 Wash the inside of the reservoir with a warm water and baking soda solution. The solution should

be about 2 tablespoons of baking soda to a quart of water.

 The drip tray and water faucets should be cleaned with mild detergent and warm water.

 At regular intervals or once a month inspect the coils located across the back of the dispenser.

Vacuum accumulation of dust or clean it with a hard brush.

TAKING DISPENSER OUT OF SERVICE

 If the water dispenser will not be used for a long period of time, unplug the power cord from the

wall outlet.

 Drain the water through the faucets.

 Turn the switch market hot to the “OFF” position.

 Drain the water from the tank by removing the plug from the back of the dispenser.

 Unit should not be transported on the sides. Place it upright if possible and cover it with a

blanket.

PROBLEMS WITH YOUR WATER DISPENSER

You can solve many common water dispenser problems easily, saving you the cost

of a possible service call. Try the suggestions outlined below to see if you can solve

the problem before calling the service.

TROUBLESHOOTING GUIDE

PROBLEM POSSIBLE CAUSE

Water dispenser does not operate.

Not plugged in.

The circuit breaker tripped or a blown fuse.

Water cooler is not cold enough. Check to be sure the cold switch on the back is ON.

The water dispenser does not have the correct

clearances.

Water dispenser hot water is not hot enough. Check to be sure the hot switch on the back is ON.

Compressor turns on and off frequently.

The room temperature is hotter than normal.

The temperature control is not set correctly.

The water dispenser does not have the correct

clearances.

Vibrations. Check to assure that the water dispenser is level.

The water dispenser seems to make too much

noise.

The rattling noise may come from the flow of the

refrigerant, which is normal.

As each cycle ends, you may hear gurgling sounds

caused by the flow of refrigerant in your water

dispenser.

Contraction and expansion of the inside walls may

cause popping and crackling noises.

The water dispenser is not level.

Bottle feels warm.

The water system is overfilled. Dispense Cold water

until air is released into the bottle.

Water bottle is hot. Water is boiling in the hot tank and bubbling up into the

bottle. Press the hot dispenser button until water flows

to remove air from the hot tank.

WARNING—THE WATER COMING OUT OF THE BACK SIDE MARKED “HOT” MAY BE SCOLDING.

SERVICE FOR YOUR WATER DISPENSER

We are proud of our customer service organization and the network of professional service

technicians that provide service on your Avanti appliances. With the purchase of your Avanti

appliance, you can have the confidence that if you ever need additional information or assistance, the

Avanti Products Customer Service team will be here for you. Just call us toll-free.

AVANTI PRODUCTS CUSTOMER SERVICES

Product Information

800-323-5029

Whatever your questions are about our products,

help is available.

Part Orders

800-220-5570

You may order parts and accessories that will be

delivered directly to your home.

You may order these items by personal check,

money order, Master Card, or Visa.

In-Home Repair Service

800-220-5570

An Avanti Products authorized service center will

provide expert repair service, scheduled at a time

that is convenient for you. Our trained servicers

know your appliance inside and out.

WIRING DIAGRAM

YOUR Avanti Products WARRANTY Staple your sales receipt here. Proof of

original purchase date is needed to obtain

service under warranty.

WHAT IS COVERED

LIMITED ONE-YEAR

WARRANTY

For one year from the date of

purchase by the original owner, Avanti

Products will, at its option, repair or

replace any part of the appliance

which proves to be defective in

material or workmanship under normal

use. During this period Avanti

Products will provide all parts and

labor necessary to correct such

defects free of charge, so long as the

appliance has been installed and

operated in accordance with the

written instructions in this manual.

Avanti Products will provide you with a

reasonably similar replacement

product that is either new or factory

refurbished. In rental or commercial

use, the warranty period is 90 days.

 Incidental or consequential damages.

 Parts and labor costs for the following will

not be considered as warranty:

 Inner door panels, door shelves, door

rails, and/or door supports.

 Light bulbs and/or plastic housing.

 Plastic cabinet liners.

 Punctured evaporator that voids the

warranty on the complete sealed system.

 Replacement of house fuses or resetting

circuit breakers.

 Shipping and Handling costs associated

with the replacement of the unit.

LIMITED SECOND THROUGH

FIFTH YEAR WARRANTY

For the second through the fifth year from date

of original purchase, Avanti Products will

provide a replacement compressor free of

charge due to a failure. You are responsible

for the service labor and freight charges. In

rental or commercial use, the limited

compressor warranty is one year and nine

months. Cost to move the appliance to the

servicers’ shop and back to the user's home,

as may be required, are the user's

responsibility.

 Repairs performed by unauthorized

servicers.

 Surcharges including, but not limited to,

any after hour, weekend, or holiday

service calls, tolls, ferry trip charges, or

mileage expense for service calls to

remote areas, including the State of

Alaska.

 Service calls that do not involve defects in

material or workmanship such as

customer education, door reversal, or

proper installation.

 Service calls that are related to external

problems, such as abuse, misuse,

inadequate electrical power, accidents,

fire, floods, or acts of God.

 Failure of the product if it is used for other

than its intended purpose.

 This warranty does not apply outside the

continental U.S.A.

WHAT IS NOT COVERED

INSTRUCCIONES EN ESPAÑOL

PLATAFORMA PARA AJUSTE DE ALTURA

 PARA PERMITIR QUE EL GRIFO DE SU DISPENSADOR DE AGUA SEA MAS ACCESIBLE,

SU UNIDAD CUENTA CON UNA PLATAFORMA PARA AJUSTE DE ALTURA. LA

PLATAFORMA REQUIERE ENSAMBLAJE TAL COMO SE ENSEÑA ABAJO.

RETIRE TODAS LAS PARTES Y LOS MATERIALES DE EMPAQUE DE LA CAJA.

A) ALINEE LA SECCION FRONTAL Y POSTERIOR DE LA PLATAFORMA Y

ENSAMBLE COMO SE MUESTRA EN LA FIGURA 1.

Fig. 1

F) ALINEE LA PLATAFORMA ENSAMBLADA CON LA PARTE INFERIOR DEL ARO DE

ESTABILIDAD COMO SE MUESTRA EN LA FIGURA 2A.

ALINEE LAS AREAS MARCADAS “1” Y “2” EN LA PLATAFORMA CON LAS MISMAS

AREAS MARCADAS “1” Y “2” DEL ARO DE ESTABILIDAD.

(NOTA: ESTAS AREAS DEBEN SER ALINEADAS CORRECTAMENTE PARA EL

ENSAMBLAJE DE LA UNIDAD. SI LA PLATAFORMA NO ESTA ALINEADA

CORRECTAMENTE AL ARO DE ESTABILIDAD, LOS CLIPS DE RETENCION

PODRÍAN SUFRIR DAÑO PERMANENTE Y CAUSAR QUE LA PLATAFORMA SEA

INESTABLE.

Fig 2a

PIEZA

FRONTAL

PIEZA

LATERAL

ARO

INFERIOR

G) ASEGURESE QUE AMBOS CLIPS EN LOS LADOS DE LA PLATAFORMA Y LOS

ORIFICIOS PARA LOS TORNILLOS SE ALINEEN CORRECTAMENTE ANTES DE

INSERTAR LOS CLIPS EN SU LUGAR RESPECTIVO DEL ARO DE ESTABILIDAD

COMO SE MUESTRA EN LA FIG 2B.

Fig 2b

H) UNA VEZ QUE HAYA ENSAMBLADO Y ASEGURADO LA PLATAFORMA Y EL ARO

DE ESTABILIDAD JUNTOS, USE LOS TORNILLOS INCLUIDOS CON LA UNIDAD Y

ASEGURE FIRMEMENTE EL ARO DE ESTABILIDAD COMO SE MUESTRA EN LA FIG

2B.

I) COLOQUE EL DISPENSADOR DE AGUA EN LA PLATAFORMA ENSAMBLADA Y

ASEGURELOS FIRMEMENTE USANDO LOS TORNILLOS QUE VIENEN INCLUIDOS.

PARA OBTENER AGUA CALIENTE:

 MUEVA HACIA LA IZQUIERDA Y NO SUELTE EL BOTON DE SEGURIDAD.

 MANTENGA AGARRADO ESE BOTON DE SEGURIDAD MIENTRAS QUE EMPUJE EL GRIFO

HACIA ABAJO PARA DISPENSAR EL AGUA CALIENTE.

 CUANDO SUELTE EL GRIFO ASEGURESE DE RETORNARLO A LA POSICION ORIGINAL.

AVISO:

ESTE GRIFO DE AGUA CALIENTE TIENE UN ADAPTADOR DE SEGURIDAD PARA

NIÑOS.

ORIFICIO

PARA EL

CLIP

SUJETADOR

DEL CLIP

ORIFICIO PARA

EL TORNILLO EN

LA PARTE

INFERIOR DEL

ARO

TORNILLO

ASEGURADOR

EN LA PIEZA

POSTERIOR

PASOS RECOMENDADOS PARA CAMBIAR EL BOTELLON

 QUITE EL BOTELLON VACIO.

 LIMPIE EL CUELLO DEL BOTELLON NUEVO CON UN TRAPO LIMPIO.

 LEVANTE EL BOTELLON HACIENDO FUERZA CON LAS PIERNAS Y NO LA ESPALDA.

 TOME EL BOTELLON POR LOS LADOS Y DIRIJA EL CUELLO DEL MISMO HACIA LA

APERTURA DEL TANQUE.

 VOLTEE EL BOTELLON COMO SI FUERA A SOLTAR AGUA E INSERTE EL CUELLO DEL

BOTELLON EN LA APERTURA DEL TANQUE HASTA QUE SE COLOQUE EN LA POSICION

CORRECTA.

DIRECCIONES BASICAS DE OPERACION:

 COLOQUE EL ENFRIADOR DE PIE POR UN PERIODO DE 2 HORAS ANTES DE ENCHUFAR

LA UNIDAD A LA PARED.

 COLOQUE EL ENFRIADOR EN UN AREA BIEN VENTILADA Y DEJE UN ESPACIO DE UN

POCO MAS DE 2 PULGADAS ENTRE LA UNIDAD Y LA PARED.

 ESCOJA UN LUGAR CON PISO NIVELADO.

 NO COLOQUE EL ENFRIADOR DONDE LA TEMPERATURA AMBIENTAL PUEDA BAJAR DE

°F (0°C).

ANTES DE ENCHUFARLO

AUNQUE ENFRIADOR SALE LIMPIO DE LA FABRICA, DEBE LIMPIAR Y ESTERILIZAR LOS

CONDUCTOS DEL TANQUE Y LOS GRIFOS DE ACUERDO A LOS SIGUIENTES PASOS:

 LLENE EL TANQUE DE AGUA (HASTA EL TOPE) CON AGUA DE LA PILA.

 DEJE NIVELAR EL AGUA POR 5 MINUTOS.

 ABRA LA LLAVE DE AGUA CALIENTE HASTA QUE SALGA AGUA Y CIERRELA

INMEDIATAMENTE.

 ENCHUFE LA UNIDAD A LA PARED.ENCRENDA LOS DOS INTERRUPTORES SITUADOS

EN LA PARTE TRASERA. LOS DOS INDICADORES DE LUZ SE ALUMBRARAN. ESPERE

HASTA QUE EL INDICADOR DE AGUA CALIENTE SE APAGUE (APROX. 10 MINUTOS).

 ENTONCES ESPERE HASTA QUE EL INDICADOR DE AGUA FRIA SE APAGUE (APROX. 5

MINUTOS).

 DESCONECTE LA UNIDAD DE LA PARED.

 EMPIEZE A DRENAR LAS LLAVES UNA A LA VEZ HASTA QUE SALGA EL ULTIMO

CHORRO DE AGUA.

 EN LA PARTE TRASERA DE LA UNIDAD ENCONTRARA UNA TAPA PLASTICA. GIRE HACIA

LA IZQUIERDA LA TAPA HASTA QUE SALGA EL ULTIMO CHORRO.

 CUANDO NO SALGA MAS AGUA DE LA APERTURA, CIERRE LA TAPA PLASTICA.

 TOME EL BOTELLON DE AGUA Y SIGA LAS INSTRUCCIONES PARA CAMBIAR EL

BOTELLON.

 ENCHUFE LA UNIDAD. AHORA SU ENFRIADOR ESTA LISTO PARA SU USO.

CONTROLES DE OPERACION

 CONTROL DE AGUA FRIA:

ABRA LA LLAVE DE AGUA FRIA (10). EL INDICADOR DE LUZ VERDE SE ENCENDERA Y

EL PROCESO DE ENFRIAMIENTO COMENZARA. CUANDO LA TEMPERATURA

ALCANCE APROXIMADAMENTE 5-7°C LA LUZ VERDE SE APAGARA

AUTOMATICAMENTE.

 CONTROL DE AGUA CALIENTE:

ABRA LA LLAVE DE AGUA CALIENTE (11). EL INDICADOR DE LUZ ROJA SE

ENCENDERA Y EL PROCESO DE CALENTAMIENTO DEL AGUA COMENZARA.

CUANDO LA TEMPERATURA ALCANCE APROXIMADAMENTE 80°C LA LUZ ROJA SE

APAGARA AUTOMATICAMENTE Y OTRO CICLO DE CALENTAMIENTO EMPEZARA.

MANTENIMIENTO

 A INTERVALOS REGULARES (UNA VEZ AL MES), INSPECCIONE EL CONDENSADOR O

REJILLA DE ALAMBRE LOCALIZADA EN LA PARTE TRASERA DE LA UNIDAD.

 ANTES DE EFECTUAR LA LIMPIEZA, DESENCHUFE EL ENFRIADOR. USE UNA

ASPIRADORA O UN CEPILLO DURO PARA QUITAR EL POLVO.

 PARA LIMPIAR LAS PARTES DE PLASTICO SE REQUIERE JABON LIQUIDO Y AGUA TIBIA.

NO USE LIMPIADORES ABRASIVOS EN LA SUPERFICIE SUPERIOR NI EN LA BANDEJA DE

ESCURRIMIENTO.

SI NO VA A USAR EL ENFRIADOR POR UN TIEMPO PROLONGADO

 DESENCHUFE LA UNIDAD.

 QUITE EL BOTELLON DE AGUA.

 COLOQUE LOS INTERRUPTORES MARCADOS CALIENTE Y FRIO (EN LA PARTE TRASERA)

EN LA POSICION “OFF”.

 DRENE EL AGUA ABRIENDO LAS LLAVES.

 DRENE LA APERTURA EN LA PARTE TRASERA QUITANDO EL TAPON.

 EL ENFRIADOR DEBE TRANSPORTARSE PARADO Y CUBIERTO CON UNA FRAZADA PARA

EVITAR QUE SE RAYE.

POSIBLES PROBLEMAS CAUSA

DERRAME DE AGUA POR FUERA DEL

ENFRIADOR

LA BOTELLA ESTA PERFORADA –

REEMPLACELA

EL AGUA NO ESTA SUFICIENTEMENTE

FRIA.

SU TEMPERATURA DEBERIA SER DE 5 A

7 C CON UNA TEMPERATURA AMBIENTE

DE 20 C. SI NO ES ASI, LLAME AL

CENTRO DE SERVICIO, EL TERMOSTATO

PODRIA ESTAR DEFECTUOSO.

EL AGUA NO ESTA SUFICIENTE CALIENTE

SU TEMPERATURA DEBERIA SER DE 80 A

90 C CON UNA TEMPERATURA AMBIENTE

DE 20 C. SI NO ES ASI, LLAME AL

CENTRO DE SERVICIO, EL TERMOSTATO

PODRIA ESTAR DEFECTUOSO.

EL ENFRIADOR NO ENFRIA O CALIENTA EL

AGUA

VERIFIQUE LOS CIRCUITOS, FUSIBLES O

DISYUNTORES.

(Page left blank intentionally)

Registration Information

Thank you for purchasing this fine Avanti product. Please fill out this form and return it to the

following address within 100 days from the date of purchase and receive these important benefits:

Avanti Products, A Division of The Mackle Co., Inc.

P.O.Box 520604 – Miami, Florida 33152

 Protect your product:

We will keep the model number and date of purchase of your new Avanti product on file to

help you refer to this information in the event of an insurance claim such as fire or theft.

 Promote better products:

We value your input. Your responses will help us develop products designed to best meet

your future needs.

-------------------------------------------------------(detach here)-------------------------------------------------------------

----

Avanti Registration Card

Name Model # Serial #

Address Date Purchased Store / Dealer Name

City State Zip E-mail Address

Area Code Phone Number Occupation

Did You Purchase An Additional Warranty As your Primary Residence, Do You:

 Extended  Own  Rent

 None

Your Age:

Reason for Choosing This Avanti Product:

Please indicate the most important factors

That influenced your decision to purchase

this product:

 under 18  18-25  26-30

 31-35  36-50  over 50

Marital Status:

 Married  Single

 Price

 Product Features

 Avanti Reputation

 Product Quality

 Salesperson Recommendation

 Other: ___________________

 Friend / Relative Recommendation

 Warranty

 Other: ___________________

Is This Product Used In The:

 Home  Business

How Did You Learn About This Product:

 Advertising

 In-Store Demo

 Personal Demo

Comments:

Version: 1-11012010 PRINTED IN CHINA

Avanti GR2013CSS Manual de usuario

Marca: Avanti

Modelo: GR2013CSS

Categoría: Dispensador de agua

Tipo: Manual de usuario

Descargar PDF

informe

en otros idiomas

English: Avanti GR2013CSS User manual

Avanti GR2013CSS Manual de usuario

Avanti GR2013CSS Manual de usuario

en otros idiomas

Artículos relacionados

Otros documentos