PowerStroke PS9C5001 El manual del propietario

Marca: PowerStroke

Modelo: PS9C5001

Categoría: Generadores de poder

Tipo: El manual del propietario

NEUTRAL BONDED TO FRAME

CONNECTEUR NEUTRE RELIÉ AU CADRE

PUNTO NEUTRO CONECTADO AL MARCO

CUSTOMER SERVICE (USA)

1-877-617-3501

SERVICE CLIENTELE (Canada)

1-877-617-3501

SERVICIO AL CLIENTE (Mexico)

01 800 843 1111

www.powerstroketools.com

To register your POWERSTROKE product, please visit:

http://register.powerstroketools.com/

Pour enregistrer votre produit de POWERSTROKE, s’il

vous plaît la visite : http://register.powerstroketools.com/

Para registrar su producto de POWERSTROKE, por favor

visita: http://register.powerstroketools.com/

NOTICE AVIS AVISO

Do not use E15 or E85 fuel (or fuel

containing greater than 10% ethanol)

in this product. It is a violation of fed-

eral law and will damage the unit and void your warranty.

Ne pas utiliser d’essence E15 ou E85 (ou un carburant

contenant plus de 10 % d’éthanol) dans ce produit. Une

telle utilisation représente une violation de la loi fédérale et

endommagera l’appareil et annulera la garantie.

No utilice combustibles E15 o E85 (ni combustibles que

contengan más de 10 % de etanol) con este producto. Esto

constituye una violación a la ley federal, dañará la unidad

y anulará la garantía.

SAVE THIS MANUAL FOR FUTURE REFERENCE

Your generator has been engineered and manufactured to our high standard for dependability, ease of operation, and operator

safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this

product. If you do not understand the warnings and instructions in the operator’s manual, do not use this product.

Ce générateur a été conçu et fabriqué conformément à nos strictes

normes de fiabilité, simplicité d’emploi et sécurité d’utilisation.

Correctement entretenu, cet outil vous donnera des années de

fonctionnement robuste et sans problème.

AVERTISSEMENT :

Pour réduire les risques de blessures, l’utilisateur doit lire

et veiller à bien comprendre le manuel d’utilisation avant

d’employer ce produit. Si tous les avertissements et toutes les

consignes de sécurités et instructions du manuel d’utilisation

ne sont pas bien compris, ne pas utiliser ce produit.

Su generador diseñado y fabricado de conformidad con nuestras

estrictas normas para brindar fiabilidad, facilidad de uso y seguri-

dad para el operador. Con el debido cuidado, le brindará muchos

años de sólido funcionamiento y sin problemas.

ADVERTENCIA:

Para reducir el riesgo de lesiones, el usuario debe leer y

comprender el manual del operador antes de usar este

producto. Si no comprende los avisos de advertencia y las

instrucciones del manual del operador, no utilice este producto.

CONSERVER CE MANUEL POUR

FUTURE RÉFÉRENCE GUARDE ESTE MANUAL PARA

FUTURAS CONSULTAS

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

5,000 WATT GENERATOR

GÉNÉRATEUR DE 5000 WATTS

GENERADOR 5 000 WATTS

PS9C5001

See this fold-out section for all of the figures

referenced in the operator’s manual.

Consulte esta sección desplegable para ver todas las figuras a

las que se hace referencia en el manual del operador.

Fig. 1

F - Oil cap/dipstick (bouchon / jauge d’huile,

tapa de relleno de aceite / varilla medidora de

aceite)

G - Oil drain plug (huiler le bouchon d’égout,

tapón de drenaje del aceite)

H - Stop switch (interruptor del apagado,

interruptor del apagado)

I - Recoil starter grip (poignée du lanceur,

mango del arrancador retráctil)

J - Air filter (filtre à air, filtro de aire)

K - Choke (volet de départ, anegador)

L - Fuel tank vapor vent (respirador del vapor del

tanque de combustible)

- Ground terminal (terminal de conexión a

tierra)

N - Fuel valve (válvula de combustible)

O - Handle lock pin (goupille de blocage de la

poignée, pasador de seguro del mango)

P - AC circuit breaker (disjoncteur c.a.,

disyuntorde circuito de CA)

Q - Handle (poignée, mango)

R - Wheel (roue, rueda)

S - Muffler (silencieux, silenciador)

A - Handle release pin (goupille de relâchement

de poignée, conjunto de pasador de afloje de

mango)

B - Fuel cap (bouchon de carburant, tapa del

tanque de combustible)

C - Fuel tank (réservoir de carburant, tanque de

combustible)

D - 120 volt AC 20 amp receptacles (réceptacles

120 volts, 20 ampères, 120 V de CA 20 A

receptáculos)

E - 240 volt AC 20 amp receptacle (réceptacle

240 volts, 20 ampères, 240 V de ca 20 A

receptáculo)

iii

Fig. 2

Fig. 3 Fig. 5 Fig. 7

A - Socket wrench (clé à douille, llave de

casquillo)

B - Combination wrench (clé mixte, llave de

combinación)

Fig. 4

A - Lock nut (écrous de blocage, tuerca de

bloqueo)

B - Frame (support, armazón)

C - Rubber foot (patin en caoutchouc, pie de

goma)

D - Bolt (boulon, perno)

A - Hitch pin (goupille d’attelage, pasador del

enganche)

B - Washer (rondelle, arandela)

C - Wheel (roue,rueda)

D - Axle (essieu, eje)

E - U-bracket (support en U, soporte en “U”)

Fig. 6

A - Lanyard (lanière, correa)

B - Handle lock pin (goupille de blocage de la

poignée, pasador de seguro del mango)

C - Handle (poignée mango)

D - Hole (trou, agujero)

A - Handle (poignée, mango)

B - Handle lock pin (goupille de blocage de la

poignée pasador de seguro del mango)

C - Handle release pin (goupille de relâchement

de poignée, conjunto de pasador de afloje de

mango)

RUN

START

CHOKE

Fig. 8

Fig. 9

Fig. 14

Fig. 12

Fig. 13

Fig. 10

Fig. 15

A - Fuel valve (robinet de carburant, válvula de

combustible)

B - Recoil starter grip (poignée du lanceur

mango, del arrancador retráctil)

A - Move choke lever left to start (tirer droite

le levier d’étranglement pour démarrer,

desplace izquierda la palanca del anegador

para arrancar)

B - Move choke lever right to run (tirer droite

le levier d’étranglement pour la marche,

desplace derecha de la palanca del anegador

para poner en marcha)

A - Air filter screw (vis du filtre à air, tornillo de

filtro de aire)

B - Air filter cover (couvercle du filtre à air, tapa

del filtro de aire)

C - Filter element (elément filtrant, elemento de

filtro)

D - Air filter unit (unité de filtre à air, unidad del

filtro de aire)

A - Oil cap/dipstick (bouchon / jauge d’huile,

tapa de relleno de aceite / varilla medidora de

aceite)

B - Oil fill hole (orifice de remplissage d’huile,

agujero de llenado de aceite)

A - Fuel cap (bouchon de carburant, tapa del

tanque de combustible)

B - Fuel tank (réservoir de carburant, tanque de

combustible)

A - Fuel valve (robinet de carburant, válvula de

combustible)

B - Stop switch (commutateur d’arrêt, interruptor

del apagado)

RUN

START

CHOKE

RUN

START

CHOKE

A B

Fig. 11

A - Spark plug (bougie, bujía)

B - Spark plug cap (creux de la bougie, tapa de

la bujía)

Fig. 21

Fig. 20

A - Fuel line (conduites de carburant, conducto

de combustible)

B - Petcock (petit robinet, llave de purga)

C - Fuel valve (robinet de carburant, válvula de

combustible)

Fig. 16

Fig. 17

A - Oil drain plug (huiler le bouchon d’égout,

tapón de drenaje del aceite)

B - Oil cap/dipstick (bouchon / jauge d’huile,

tapa de relleno de aceite / varilla medidora de

aceite)

Fig. 18

A - Carburetor drain screw (carburetor drain

screw, tornillo de drenaje del carburador)

Fig. 22

A - Fuel line (conduites de carburant, conducto

de combustible)

B - Fuel filter (filtre à carburant, filtro de

combustible)

Fig. 19

A - Fuel valve (robinet de carburant, válvula de

combustible)

B - Petcock (petit robinet, llave de purga)

Page 2 — English

 Introduction .................................................................................................................................................................... 2

 Important Safety Instructions .....................................................................................................................................3-4

 Specific Safety Rules ..................................................................................................................................................... 4

 Symbols ......................................................................................................................................................................5-7

 Electrical .....................................................................................................................................................................8-9

 Features ...................................................................................................................................................................... 10

 Assembly ................................................................................................................................................................11-12

 Operation ................................................................................................................................................................12-14

 Maintenance ...........................................................................................................................................................15-17

 Troubleshooting ........................................................................................................................................................... 18

 Warranty ..................................................................................................................................................................19-22

 Parts Ordering / Service..................................................................................................................................Back Page

This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability

have been given top priority in the design of this product, making it easy to maintain and operate.

DANGER:

GROUNDING THE GENERATOR

To reduce the risk of shock or electrocution, generator must be properly grounded. The

nut and ground terminal on the frame must always be used to connect the generator to

a suitable ground source. The ground path should be made with #8 size wire. Connect

the terminal of the ground wire between the lock washer and the nut, and tighten

the nut fully. Connect the other end of the wire securely to a suitable ground source.

The National Electric Code contains several practical ways in which to establish a

good ground source. If a steel or iron rod is used, it should be at least 5/8 in. diameter,

and if a nonferrous rod is used, it should be at least 1/2 in. diameter and be listed

as material for grounding. Drive the rod or pipe to a depth of 8 ft. If a rock bottom is

encountered less than 4 ft. down, bury the rod or pipe in a trench.

All electrical tools and appliances operated from this generator must be properly grounded by use

of a third wire or be “Double Insulated.”

It is recommended to:

1. Use electrical devices with 3-prong grounded plugs.

2. Use an extension cord intended for outdoor use with a 3-pole receptacle and a 3-prong plug at opposite ends to

ensure continuity of the ground protection from the generator to the appliance.

Check and adhere to all applicable federal, state, and local regulations relating to grounding specifications. Consult a

qualified electrician or service personnel if the grounding instructions are not completely understood or if in doubt as

to whether the generator is properly grounded.

TABLE OF CONTENTS

INTRODUCTION

Page 3 — English

IMPORTANT SAFETY INSTRUCTIONS

DANGER:

Carbon Monoxide. Using a generator indoors CAN KILL

YOU IN MINUTES.

Generator exhaust contains high levels of carbon mon-

oxide (CO), a poisonous gas you cannot see or smell. If

you can smell the generator exhaust, you are breathing

CO. But even if you cannot smell the exhaust, you could

be breathing CO.

 Never use a generator inside homes, garages, crawl-

spaces, or other partly enclosed areas. Deadly levels

of carbon monoxide can build up in these areas. Us-

ing a fan or opening windows and doors does NOT

supply enough fresh air.

 ONLY use a generator outdoors and far away from

open windows, doors, and vents. These openings

can pull in generator exhaust.

Even when you use a generator correctly, CO may

leak into the home. ALWAYS use a battery-powered or

battery-backup CO alarm in the home.

If you start to feel sick, dizzy, or weak after the generator

has been running, move to fresh air RIGHT AWAY. See a

doctor. You could have carbon monoxide poisoning.

WARNING:

Read and understand all instructions. Failure to follow

all instructions listed below could result in electrocution,

fire, and/or carbon monoxide poisoning, which can cause

death or serious injury.

DANGER:

National Electric Code requires generator to be grounded

to an approved earth ground. Before using the ground ter-

minal, consult a qualified electrician, electrical inspector,

or local agency having jurisdiction for local codes or or-

dinances that apply to the intended use of the generator.

SAVE THESE INSTRUCTIONS

This manual contains important instructions for this product

that should be followed during installation and maintenance

of the generator.

 Do not connect to a building’s electrical system unless

the generator and transfer switch have been properly

installed and the electrical output has been verified by

a qualified electrician. The connection must isolate the

generator power from utility power and must comply with

all applicable laws and electrical codes.

 Do not allow children or untrained individuals to use this

unit.

 Do not start or operate the engine in a confined space,

building, near open windows, or in other unventilated space

where dangerous carbon monoxide fumes can collect.

Carbon monoxide, a colorless, odorless, and extremely

dangerous gas, can cause unconsciousness or death.

 Keep all bystanders, children, and pets at least 10 feet

away.

 Wear sturdy and dry shoes or boots. Do not operate while

barefoot.

 Do not operate generator when you are tired or under the

influence of drugs, alcohol, or medication.

 Keep all parts of your body away from any moving parts

and all hot surfaces of the unit.

 Do not touch bare wire or receptacles.

 Do not use generator with electrical cords which are worn,

frayed, bare, or otherwise damaged.

 Before storing, allow the engine to cool and drain fuel

from the unit.

 Do not operate or store the generator in rain, snow, or

wet weather.

 Store the generator in a well-ventilated area with the fuel

tank empty. Fuel should not be stored near the generator.

 Empty fuel tank, close fuel valve, and restrain the unit

from moving before transporting in a vehicle.

 Allow engine to cool for five minutes before refueling.

 To reduce the risk of fire and burn injury, handle fuel with

care. It is highly flammable.

 Do not smoke while handling fuel.

 Store fuel in a container approved for gasoline.

 Position the unit on level ground, stop engine, and allow

to cool before refueling.

 Loosen fuel cap slowly to release pressure and to keep

fuel from escaping around the cap.

 Tighten the fuel cap securely after refueling.

 Wipe spilled fuel from the unit.

 Never attempt to burn off spilled fuel under any circum-

stances.

 Generators vibrate in normal use. During and after the

use of the generator, inspect the generator as well as

extension cords and power supply cords connected to

it for damage resulting from vibration. Have damaged

items repaired or replaced as necessary. Do not use plugs

or cords that show signs of damage such as broken or

cracked insulation or damaged blades.

 For power outages, permanently installed stationary gen-

erators are better suited for providing back-up power to

the home. Even a properly connected portable generator

can become overloaded. This may result in overheating

or stressing the generator components, possibly leading

to generator failure.

Page 4 — English

IMPORTANT SAFETY INSTRUCTIONS

SPECIFIC SAFETY RULES

 Use only authorized replacement parts and accessories

and follow instructions in the Maintenance section of this

manual. Use of unauthorized parts or failure to follow main-

tenance instructions may create a risk of shock or injury.

 Maintain the unit per maintenance instructions in this

Operator’s Manual.

 Inspect the unit before each use for loose fasteners, fuel

leaks, etc. Replace damaged parts.

WARNING:

When this generator is used to supply a building

wiring system: generator must be installed by a quali-

fied electrician and connected to a transfer switch as

a separately derived system in accordance with NFPA

70, National Electrical Code. The generator shall be

connected through a transfer switch that switches all

conductors other than the equipment grounding con-

ductor. The frame of the generator shall be connected to

an approved grounding electrode. Failure to isolate the

generator from power utility can result in death or injury

to electric utility workers.

 Do not use this generator to provide power for emergency

medical equipment or life support devices.

 This generator has a neutral bonded condition. This

means the neutral conductor is electrically connected to

the frame of the machine.



Exhaust contains poisonous carbon monoxide, a colorless,

odorless gas. Breathing exhaust can cause loss of con-

sciousness and can lead to death. If running in a confined

or partially-enclosed area, the air may contain a danger-

ous amount of carbon monoxide. To keep exhaust fumes

from building up, always provide adequate ventilation.



Always use a battery-powered carbon monoxide detec-

tor when running the generator. If you begin to feel sick,

dizzy, or weak while using the generator, shut it off and

get to fresh air immediately. See a doctor. You may have

carbon monoxide poisoning.



Place the generator on a flat, stable surface with a slope

of no more than 4°.



Operate in a well-ventilated, well-lit area isolated from

working areas to avoid noise interference.



Operating the generator in wet conditions could result in

electrocution. Keep the unit dry.



Keep the generator a minimum of 3 feet away from all

types of combustible material.



Do not operate generator near hazardous material.



Do not operate generator at a gas or natural gas filling

station.



Do not touch the muffler or cylinder during or immediately

after use; they are HOT and will cause burn injury.

 Do not allow the generator’s gas tank to overflow when

filling. Fill to 1 in. below the top neck of the gasoline tank

to allow for fuel expansion. Do not cover the fuel tank cap

when the engine is running. Covering the fuel tank cap

during use may cause engine failure and/or damage to

the tool.



Do not smoke when filling the generator with gasoline.



Shut down the engine and allow to cool completely before

adding gasoline or lubricant to the generator.



Do not remove the oil dipstick or the fuel tank cap when

the engine is running.



Pay close attention to all safety labels located on the

generator.



Keep children a minimum of 10 feet away from the gen-

erator at all times.



The unit operates best in temperatures between 23°F and

104°F with a relative humidity of 90% or less.



Operating voltage and frequency requirement of all

electronic equipment should be checked prior to plug-

ging them into this generator. Damage may result if the

equipment is not designed to operate within a +/- 10%

voltage variation, and +/- 3 hz frequency variation from

the generator name plate ratings. To avoid damage, al-

ways have an additional load plugged into the generator

if solid state equipment (such as a television set) is used.

A power line conditioner is recommended for some solid

state applications.

 For outdoor use only.



Save these instructions. Refer to them frequently and use

them to instruct others who may use this product. If you loan

someone this product, loan them these instructions also.

Page 5 — English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual To reduce the risk of injury, user must read and understand

operator’s manual before using this product.

Wet Conditions Alert Do not expose to rain or use in damp locations.

Electric Shock Failure to use in dry conditions and to observe safe practices can

result in electric shock.

Toxic Fumes

Running generator gives off carbon monoxide, an odorless, color-

less, poison gas. Breathing carbon monoxide can cause nausea,

fainting, or death.

Fire/Explosion Fuel and its vapors are extremely flammable and explosive. Fire

or explosion can cause severe burns or death.

Hot Surface To reduce the risk of injury or damage, avoid contact with any hot

surface.

Lifting Hazard To reduce the risk of serious injury, avoid attempting to lift the

generator alone.

Ground Consult with local electrician to determine grounding requirements

before operation.

Electrocution Failure to properly ground generator can result in electrocution,

especially if the generator is equipped with a wheel kit.

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result

in death or serious injury.

WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result

in death or serious injury.

CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in

minor or moderate injury.

NOTICE: (Without Safety Alert Symbol) Indicates important information not related to an

injury hazard, such as a situation that may result in property damage.

Page 6 — English

 You WILL be KILLED or SERIOUSLY

HURT if you do not follow the

Operator’s Manual instructions.

 Risk of Fire. Do not add fuel while

the product is operating.

 Generator is a potential source

of electric shock. Do not expose

to moisture, rain, or snow. Do not

operate with wet hands or feet.

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

hrs Hours Time

gal Gallon Volume

qt Quart Volume

SAFETY LABELS

The information below can be

found on the generator. For

your safety, please study and

understand all of the labels before

starting the generator.

If any of the labels come off the

unit or become hard to read,

contact an authorized service

center for replacement.

 Do not expose to rain or use in damp

locations.

 Using a generator indoors CAN KILL

YOU IN MINUTES. Generator exhaust

contains carbon monoxide. This is a

poison you cannot see or smell.

 NEVER use inside a home or garage,

EVEN IF doors and windows are open.

 Only use OUTSIDE and far away from

windows, doors, and vents.

 Exhaust contains poisonous carbon

monoxide gas that can cause

unconsciousness or DEATH. Operate

in well-ventilated, outdoor areas away

from open windows or doors.

 Failure to properly ground generator

can result in electrocution, especially

if the generator is equipped with a

wheel kit.

You WILL be KILLED or SERIOUSLY

HURT if you do not follow the Operator’s

Manual instructions.

Ne pas procéder de la manière décrite

dans ce Manuel d’utilisation entraînera

des BLESSURES GRAVES voire la MORT.

SE MATARÁ o LESIONARÁ GRAVEMENTE

si no sigue las instrucciones del Manual

del operador.

Risk of fire. Do not add fuel while the

product is operating.

Risque d’incendie. Ne pas ajouter de

carburant pendant l’utilisation de

l’appareil.

Riesgo del incendio. No agregue

combustible cuando el producto esté

functionando.

Generator is a potential source of electric

shock. Do not expose to moisture, rain, or

snow. Do not operate with wet hands or feet.

Le générateur est une source potentielle

de chocs électriques. Ne pas exposer à l’humidité,

la pluie ou la neige. Ne pas utiliser avec les

mains ou les pieds mouillés.

El generador es una fuente de descarga eléctrica.

No lo exponga a humedad, la lluvia, nin a la

nieve. No opere con manos o pies húmedos.

Exhaust contains poisonous carbon monoxide

gas that can cause unconsciousness or DEATH.

Operate in well ventilated, outdoor areas away

from open windows or doors.

L’échappement contient le gaz monoxyde de

carbone toxique qui peut causer l’inconscience

ou la MORT. Fonctionner dans les secteurs

bien ventilés et extérieurs loin d’ouvre des

fenêtres ou des portes.

El escape contiene gas venenoso de monóxido

de carbono que puede causar pérdida del

conocimiento o MUERTE. Opere en áreas exteriores

bien ventiladaslejos de puertas o ventanas abiertas.

Failure to properly ground generator can

result in electrocution, especially if the

generator is equipped with a wheel kit.

Une mauvaise mise à la terre du générateur

peut causer une électrocution, surtout si le

générateur est équipé d’un kit de roue.

La omisión de conectar a tierra

adecuadamente el generador puede resultar

en electrocución, especialmente si el

generador está equipado con un kit de ruedas.

Do not expose to rain or use in damp

locations.

Ne pas exposer à la pluie ou l’humidité.

No exponga a la lluvia ni use en lugares

húmedos.

DANGER PELIGRO

DANGER

940654199-01

DANGER DANGER

PELIGRO

L’utilisation d’une génératrice à l’intérieur PEUT VOUS TUER ENQUELQUES MINUTES.

Les génératrices produisent du monoxyde de carbone, un gaz mortel incolore et inodore.

NE JAMAIS utiliser à l’intérieur d’une maison ou d’un garage,MÊME SI les portes et

les fenêtres sont ouvertes.

Utiliser uniquement À L’EXTÉRIEUR et loin des fenêtres, des portes et des évents.

Usar un generador en el interior PUEDE MATARLO EN POCOS MINUTOS.

Los gases de escape del generador contienen monóxido de carbono. Es un veneno

que no puede verse ni olerse.

NUNCA lo use dentro de su hogar o del garaje, INCLUSO con las puertas y las

ventanas abiertas.

Sólo utilícelo AL AIRE LIBRE y lejos de ventanas, puertas y respiraderos.

Using a generator indoors CAN KILL YOU IN MINUTES.

Generator exhaust contains carbon monoxide. This is a

poison you cannot see or smell.

NEVER use inside a home

or garage, EVEN IF doors

and windows are open.

Only use OUTSIDE and

far away from windows,

doors, and vents.

Page 7 — English

SYMBOLS

FUEL WARNING

No smoking when filling with gasoline.

Do not overfill. Full level is 1 in. below

the top of the fuel neck. Stop the en-

gine for five minutes before refueling to

avoid the heat from the muffler igniting

fuel vapors.

ENGINE LUBRICANT WARNING

You must add lubricant before first

operating the generator. Always check

the lubricant level before each opera-

tion. The lubricant level should always

the dipstick. The unit is equipped with

a sensor which will automatically shut

off the engine if the lubricant level falls

below a safe limit.

GROUNDING WARNING

National Electric Code requires gen-

erator to be grounded to an approved

earth ground.

HOT SURFACE WARNING

Do not touch the muffler or aluminum

cylinder of the engine. They are very HOT

and will cause severe burns. Don’t put

any flammable or combustible materials

in the direct path of the exhaust.

CLEARANCE WARNING

While operating and storing, keep at

least 3 feet of clearance on all sides of

this product, including overhead. Al-

low a minimum of 30 minutes of “cool

down” time before storage. Heat creat-

ed by muffler and exhaust gases could

be hot enough to cause serious burns

and/or ignite combustible objects.

SPARK ARRESTOR

Operation of this equipment may create

sparks that can start fires around dry

vegetation. A spark arrestor may be re-

quired. The operator should contact lo-

cal fire agencies for laws or regulations

relating to fire prevention requirements.

940513001-04

Product does not include ground rod or copper wire. National Electric Code requires generator to be

properly grounded to an approved earth ground. Call an electrician for local grounding requirements.

Le produit ne comprend pas de piquet de terre ou de fil en cuivre. Le code electrique americain

(National Electric Code) requiert un générateur pour une bonne mise à la terre approuvée. Appeler un

électricien pour connaître les exigences locales de mise à la terre.

El producto no incluye el ealambre de cobre ni la barra de conexión a tierra. Los Reglamentos

Nacionales de Electricidad exigen que el generador esté debidamente conectado a una tierra aprobada.

Comuniquese con un electrista para todo lo relacionado con los requistos de conexión a tierra.

HOT SURFACE

SURFACES TRÉS CHAUDE

SUPERFICIES CALIENTE

WARNING

AVERTISSEMENT

ADVERTENCIA

940680027-03

CHECK LUBRICANT

940708019-03

Risk of Fire. Check for any fuel overflow or leaking. Stop the engine before refueling.

DANGERDANGER PELIGRO

Risque d’incendie. Vérifier l'absence de débordement ou de fuite de carburant.

Arrêter le moteur avant de fair le plein.

Riesgo de incendio. Revise si hay algún derrame o fuga de combustible. Apague el

motor antes de poner combustible. 940974007-04

DANGERDANGER PELIGRO

940974089-02

Risk of Fire. Keep all objects at least 3 feet away from this machine. Heat from Muffler and Exhaust gases

can ignite combustible objects.

Risque d’incendie. Éloigner tous les objets au moins de 91,4 cm (3 pi) de cet appareil. La chaleur

du pot d’échappement et les gaz d’échappement peuvent enflammer les objets combustibles.

Riesgo de incendio. Mantener todos los objetos a una distancia mínima de 91,4 cm (3 pies) de esta

máquina. El calor de los gases del silenciador y el escape pueden prender fuego a objetos combustibles.

Operation of this equipment may create sparks that can start fires

around dry vegetation. A spark arrestor may be required. The operator should contact

local fire agencies for laws or regulations relating to fire prevention requirements.

WARNING

AVERTISSEMENT

L’utilisation de cet équipement peut créer des étincelles

susceptibles d’enflammer la végétation sèche. Il peut être nécessaire d’utiliser un

pare-étincelles. L’utilisateur doit communiquer avec le service local d’incendie pour

connaître toutes les lois et tous les règlements portant sur les exigences en matière

de prévention des incendies.

940947003-03

ADVERTENCIA

El uso de este equipo puede producir chispas propensas a

iniciar incendios cerca de vegetación seca. Es posible que se necesite un parachis-

pas. El operador debe ponerse en contacto con las agencias contra incendios locales

para conocer las leyes y regulaciones relacionadas con los requisitos de prevención

de incendios.

Page 8 — English

EXTENSION CORD CABLE SIZE

Refer to the table below to ensure the cable size of the extension cords you use are capable of carrying the required load.

Inadequate size cables can cause a voltage drop, which can burn out the appliance and overheat the cord.

Current in

Amperes

Load in Watts Maximum Allowable Cord Length

At 120V At 240V #8 Wire #10 Wire #12 Wire #14 Wire #16 Wire

2.5 300 600 1000 ft. 600 ft. 375 ft. 250 ft.

5 600 1200 500 ft. 300 ft. 200 ft. 125 ft.

7.5 900 1800 350 ft. 200 ft. 125 ft. 100 ft.

10 1200 2400 250 ft. 150 ft. 100 ft. 50 ft.

15 1800 3600 150 ft. 100 ft. 65 ft.

20 2400 4800 175 ft. 125 ft. 75 ft.

25 3000 6000 150 ft. 100 ft.

30 3600 7200 125 ft. 65 ft.

40 4800 9600 90 ft.

ELECTRIC MOTOR LOADS

It is characteristic of common electric motors in normal operation to draw up to six times their running current while starting.

This table may be used to estimate the watts required to start electric motors; however, if an electric motor fails to start or

reach running speed, turn off the appliance or tool immediately to avoid equipment damage. Always check the requirements

of the tool or appliance being used compared to the rated output of the generator.

Motor Size (H.P.) Running Watts Watts Required to Start Motor

Universal Capacitor Split Phase

1/8 275 N/A 850 1200

1/6 275 600 850 2050

1/4 400 800 1050 2400

1/3 450 950 1350 2700

1/2 600 1000 1800 3600

3/4 850 1200 2600 —

1 1100 N/A 3300 —

NOTICE:

Operating voltage and frequency requirement of all electronic equipment should be checked prior to plugging them into

this generator. Damage may result if the equipment is not designed to operate within a +/- 10% voltage variation, and

+/- 3 hz frequency variation from the generator name plate ratings. To avoid damage, always have an additional load

plugged into the generator if solid state equipment (such as a television set) is used. A power line conditioner is recom-

mended for some solid state applications.

ELECTRICAL

Page 9 — English

Example:

Tool or Appliance Running

Watts*

Additional

Starting Watts*

RV Air Conditioner

(11,000 BTU) 1010 1600

TV (Tube Type) 300 0

RV Refrigerator 180 600

Radio 200 0

Light (75 Watts) 300 0

Coffee Maker 600 0

2590 Total

Running Watts

1600 Highest

Starting Watts

Total Running Watts 2590

Highest Starting Watts + 1600

Total Starting Watts Needed 4190

GENERATOR CAPACITY

Make sure the generator can supply enough continuous (run-

ning) and surge (starting) watts for the items you will power

at the same time. Follow these simple steps.

1. Selecttheitemsyouwillpoweratthesametime.

2. Totalthecontinuous(running)wattsoftheseitems.This

is the amount of power the generator must produce to

keep the items running. See the wattage reference chart

at right.

3. Estimatehowmanysurge(starting)wattsyouwillneed.

Surge wattage is the short burst of power needed to start

electric motor-driven tools or appliances such as a circular

saw or refrigerator. Because not all motors start at the

same time, total surge watts can be estimated by adding

only the item(s) with the highest additional surge watts to

the total rated watts from step 2.

NOTICE:

Do not overload the generator’s capacity. Exceeding the

generator’s wattage/amperage capacity may damage

the generator and/or electrical devices connected to it.

ELECTRICAL

POWER MANAGEMENT

To prolong the life of the generator and attached devices,

it is important to take care when adding electrical loads to

the generator. There should be nothing connected to the

generator outlets before starting its engine. The correct and

safe way to manage generator power is to sequentially add

loads as follows:

1. With nothing connected to the generator, start the engine

as described later in this manual.

2. Plug in and turn on the first load, preferably the largest

load you have.

3. Permit the generator output to stabilize (engine runs

smoothly and attached device operates properly).

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

Never add more loads than the generator capacity. Take

special care to consider surge loads in generator capacity

as previously described.

Tool or Appliance

Estimated*

Running

Watts

Estimated*

Additional

Starting Watts

Home / Emergency

Incandescent Lights

(4 Quantity x 75 Watts) 300 0

TV (Tube Type) 300 0

Sump Pump (1/3 hp) 800 1300

Refrigerator or Freezer 700 2200

Well Pump (1/3 hp) 1000 2000

Furnace (1/2 hp) 800 2350

Radio 200 0

Tools

Drill (3/8", 4 amps) 440 600

Circular Saw

(Heavy Duty, 7-1/4")

1400 2300

Recip Saw 960 960

Miter Saw (10") 1800 1800

Table Saw (10") 2000 2000

*Wattages listed are approximate. Check tool or equipment for actual wattage.

Page 10 — English

KNOW YOUR GENERATOR

See Figure 1.

The safe use of this product requires an understanding of the

information on the product and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

AC CIRCUIT BREAKER

The circuit breaker is provided to protect the generator

against electrical overload. The circuit breaker may be reset

by flipping down and back up.

AIR FILTER

The air filter helps to limit the amount of dirt and dust drawn

into the unit during operation.

CHOKE LEVER

The choke lever is used when starting the engine.

FUEL TANK

The fuel tank has a capacity of 6 gallons.

FUEL VALVE

Fuel flow from the fuel tank to the engine is turned on and

off using the fuel valve.

GROUND TERMINAL

The ground terminal is used to assist in properly ground-

ing the generator to help protect against electrical shock.

Consult with a local electrician for grounding requirements

in your area.

LOW OIL SHUT DOWN PROTECTOR

The low oil sensor causes the engine to stop if the level of

oil in the crankcase is insufficient.

OIL CAP/DIPSTICK

Remove the oil fill cap to check and add lubricant to the

generator when necessary.

OIL DRAIN PLUG

When changing the engine lubricant, unscrew and remove

the oil drain plug to allow old engine lubricant to be drained.

RECEPTACLES

Your generator has the following single phase, 60 Hz out-

lets: one 240 Volt AC 20 Amp twist lock receptacle and two

120 Volt AC, 20 Amp duplex receptacles. These can be used

for operating appropriate appliances, electrical lighting, tools,

and motor loads.

RECOIL STARTER GRIP

The recoil starter grip is used to start the generator’s engine.

STOP SWITCH

The generator has a stop switch near the fuel valve. To turn

the engine off, press and hold the STOP switch until the

engine stops.

FEATURES

PRODUCT SPECIFICATIONS

ENGINE

Engine Type .......................................................389cc OHV

Spark Plug ................................................ Torch/LG F6RTC

Engine Lubricant Volume........................................... 37 oz.

Fuel Volume ................................................................ 6 gal.

GENERATOR

Rated Voltage ...................................................120V / 240V

Rated Amps ................................................... 41.7A / 20.8A

Rated Running Watts* ............................................5,000 W

Rated Starting Watts ..............................................6,250 W

Rated Frequency ........................................................60 Hz

DIMENSIONS

Length ..................................................................... 28.5 in.

Width ....................................................................... 20.9 in.

Height ...................................................................... 24.1 in.

Weight .................................................................... 190 lbs.

*Rated running watts determined by PGMA Standard G200

Page 11 — English

UNPACKING

This product requires assembly.

 Carefully cut the box down the sides then remove the

machine and any accessories from the box. Make sure

that all items listed in the loose parts list are included.

NOTE: This machine is heavy and requires a minimum of

two people to lift. To avoid back injury, lift with your legs

and not your back.

WARNING:

Do not use this product if any parts on the Loose Parts

List are already assembled to your product when you

unpack it. Parts on this list are not assembled to the

product by the manufacturer and require customer instal-

lation. Use of a product that may have been improperly

assembled could result in serious personal injury.

 Inspect the unit carefully to make sure no damage oc-

curred during shipping.

 Do not discard the packing material until you have carefully

inspected and satisfactorily operated the product.

 If any parts are damaged or missing, please call

1-877-617-3501 for assistance.

WARNING:

If any parts are damaged or missing do not operate this

product until the parts are replaced. Use of this product

with damaged or missing parts could result in serious

personal injury.

WARNING:

Do not attempt to modify this product or create acces-

sories not recommended for use with this product. Any

such alteration or modification is misuse and could result

in a hazardous condition leading to possible serious

personal injury.

WARNING:

Do not attempt to operate the generator until assembly

is complete. Failure to comply could result in possible

serious personal injury.

LOOSE PARTS LIST

See Figure 2

The following items are included with the generator:

Key

No. Description Qty.

1 Axle ......................................................................2

2 Wheel ...................................................................2

3 Washer ................................................................. 2

4 Hitch Pin ..............................................................2

5 Bolt ......................................................................2

6 Rubber Foot ........................................................2

7 Lock Nut ..............................................................2

8 Bottle of Engine Lubricant ...................................1

Operator’s Manual (not shown) ...........................1

TOOLS NEEDED

See Figure 3.

The following tools (not included or drawn to scale) are

needed for assembly:

 Socket Wrench

 Combination Wrench

NOTE: Do not put fuel or lubricant in the generator before

installing the feet and wheels.

INSTALLING FEET ON THE FRAME

See Figure 4.

 Locate the following items:

2 rubber feet

2 lock nuts

2 bolts

 Insert bolt through rubber foot and then through frame

as shown.

 Thread lock nut onto bolt and tighten one full turn past

snug.

NOTE: Be careful not to overtighten so that foot mate-

rial collapses.

 Repeat with remaining foot.

ASSEMBLY

Page 12 — English

INSTALLING THE WHEELS

See Figure 5.

Wheels are provided to assist in moving the generator to

the desired location and should be installed on the side

opposite the handle.

 Locate the following items:

2 axle

2 washers

2 wheels

2 hitch pins

 Raise the end of the generator opposite the recoil starter

high enough to gain access to the frame bottom; securely

position props underneath to support.

 Insert axle through the center of the wheel.

 Place washer on axle and then slide the axle through the

bracket on the frame.

 Push the hitch pin into the hole on the end of the axle to

secure the wheel assembly.

NOTE: The hitch pin should be pushed into the axle until

the center of the pin rests on top of the axle.



Repeat the process on the other side to install second

wheel.

ASSEMBLY

OPERATION

DANGER:

Carbon Monoxide. Using a generator indoors CAN KILL

YOU IN MINUTES.

Generator exhaust contains high levels of carbon mon-

oxide (CO), a poisonous gas you cannot see or smell. If

you can smell the generator exhaust, you are breathing

CO. But even if you cannot smell the exhaust, you could

be breathing CO.

 Never use a generator inside homes, garages, crawl-

spaces, or other partly enclosed areas. Deadly levels

of carbon monoxide can build up in these areas. Us-

ing a fan or opening windows and doors does NOT

supply enough fresh air.

 ONLY use a generator outdoors and far away from

open windows, doors, and vents. These openings

can pull in generator exhaust.

Even when you use a generator correctly, CO may

leak into the home. ALWAYS use a battery-powered or

battery-backup CO alarm in the home.

If you start to feel sick, dizzy, or weak after the generator

has been running, move to fresh air RIGHT AWAY. See

a doctor. You could have carbon monoxide poisoning.

DANGER:

Failure to properly ground generator can result in elec-

trocution, especially if the generator is equipped with a

wheel kit. National Electric Code requires generator to be

properly grounded to an approved earth ground. Call an

electrician for local grounding requirements.

WARNING:

Do not allow familiarity with this product to make you

careless. Remember that a careless fraction of a second

is sufficient to inflict serious injury.

WARNING:

Do not use any attachments or accessories not recom-

mended by the manufacturer of this product. The use of

attachments or accessories not recommended can result

in serious personal injury.

Page 13 — English

OPERATION

APPLICATIONS

This generator is designed to supply electrical power for

operating compatible electrical lighting, appliances, tools,

and motor loads.

BEFORE OPERATING THE UNIT

 Only use OUTSIDE and far away from windows, doors,

and vents.

 NEVER use inside a home or garage, EVEN IF doors and

windows are open.

 Always position the generator on a flat firm surface.

SPECIAL REQUIREMENTS:

There may be General or State Occupational Safety and

Health Administration (OSHA) regulations, local codes or

ordinances that apply to the intended use of the generator.

Please consult a qualified electrician, electrical inspector, or

the local agency having jurisdiction:

 In some areas, generators are required to be registered

with local utility companies.

 If the generator is used at a construction site, there may

be additional regulations which must be observed.

RAISING AND LOWERING THE HANDLE

See Figure 6 - 7.

 Attach the lanyard to the handle lock pin and generator.

 To raise the handle (for moving the generator): pull the

handle release pin out and raise the handle. Release the

handle release pin and insert the handle lock pin to secure

the handle in place.

 To lower the handle (for storing or transporting the gen-

erator): remove the handle lock pin, then pull the handle

release pin out and lower the handle to the down position.

Never use the handle to lift the generator. The handle should

only be used for moving the unit by rolling it on its wheels.

CHECKING/ADDING LUBRICANT

See Figure 8.

NOTICE:

Attempting to start the engine before it has been properly

filled with lubricant will result in equipment failure.

Engine lubricant has a major influence on engine perfor-

mance and service life. For general, all-temperature use,

SAE 10W-30 is recommended. Always use a 4-stroke motor

lubricant that meets or exceeds the requirements for API

service classification SJ.

NOTE: Non-detergent or 2-stroke engine lubricants will

damage the engine and should not be used.

 Turn the fuel valve to the OFF position.

 Unscrew the oil cap/dipstick and remove.

 Wipe dipstick clean and re-seat in hole; do not rethread.

 Remove dipstick again and check lubricant level. Lubri-

cant level should fall between the hatched areas on the

dipstick.

 If level is low, add engine lubricant until the fluid level rises

to the upper portion of the dipstick.

 Replace and secure the oil cap/dipstick.

USING FUEL STABILIZER

Fuel gets old, oxidizes, and breaks down over time. Adding

a fuel stabilizer (not included) extends the usable life of fuel

and helps prevent deposits from forming that can clog the

fuel system. Follow fuel stabilizer manufacturer’s directions

for correct ratio of stabilizer to fuel.

 Mix fuel stabilizer and gasoline prior to filling the tank

by using a gas can or other approved fuel container and

shaking gently to combine.

NOTE: To control the amount of fuel stabilizer being added

to the engine, always mix fuel stabilizer with gasoline

before fueling the tank rather than adding fuel stabilizer

directly into the generator’s fuel tank.

 Replace and secure the fuel tank cap.

 Start and run the engine for at least 5 minutes to allow

stabilizer to treat the entire fuel system.

OXYGENATED FUELS

NOTICE:

Do not use E15 or E85 fuel (or fuel containing greater

than 10% ethanol) in this product. It is a violation of

federal law and will damage the unit and void your

warranty.

Fuel system damage or performance problems resulting

from the use of an oxygenated fuel containing more than

the percentage of oxygenates stated below are not covered

under warranty.

Ethanol. Gasoline containing up to 10% ethanol by volume

(commonly referred to as E10) is acceptable. E15 and E85

are not.

CHECKING/ADDING FUEL

See Figure 9.

WARNING:

Gasoline and its vapors are highly flammable and ex-

plosive. To prevent serious personal injury and property

damage, handle gasoline with care. Keep away from igni-

tion sources, handle outdoors only, do not smoke while

adding fuel, and wipe up spills immediately.

Page 14 — English

When adding gas to the generator, make sure the unit is

sitting on a flat, level surface. If the engine is hot, let the

generator cool before adding gas. ALWAYS fill the fuel tank

outdoors with the machine turned off.

 Remove the fuel cap.

 Fill the fuel tank to 1 in. below the top of the fuel neck.

 Replace and secure the fuel cap.

NOTE: Always use unleaded gasoline with a pump octane

rating of 86 or higher. Never use old, stale, or contaminated

gasoline, and do not use an oil/gas mixture. Do not allow dirt

or water into the fuel tank. Do not use E85 fuel.

STARTING THE ENGINE

See Figures 10 - 12.

NOTICE:

On a level surface with the engine off, check the lubricant

level before each use of the generator.

NOTE: If location of generator is not level, the unit may not

start or may shut down during operation.

 Unplug all loads from the generator.

 Turn the fuel valve to the ON position.

 Move the choke lever left to the START position.

NOTE: If engine is warm or the temperature is above

50˚F,movethechokeleverrighttotheRUNposition.

 Pull the recoil starting grip until the engine runs (a maxi-

mum of 6 times).

NOTE: Do not allow the grip to snap back after starting;

return it gently to its original place.

 Allow the engine to run for 15 - 30 seconds, then move

the choke to the RUN position.

STOPPING THE ENGINE

See Figure 12.

To stop the engine under normal operating conditions:

 Remove any load from the generator.

 Turn the fuel valve to the OFF position.

 Press and hold the STOP switch until the engine stops.

To stop the unit quickly in an emergency:

 Press and hold the STOP switch until the engine stops.

WARNING:

While operating and storing, keep at least 3 feet of clear-

ance on all sides of this product, including overhead.

Allow a minimum of 30 minutes of “cool down” time be-

fore storage. Heat created by muffler and exhaust gases

can be hot enough to cause serious burns and/or ignite

combustible objects.

MOVING THE GENERATOR

See Figure 13.

 Turn off the generator.

 Raise the handle to the up position.

 Disconnect any equipment that is plugged into the gen-

erator.

 Turn the fuel valve to the OFF position.

 Allow 30 minutes of “cool down” time before storing the

machine.

 For security, insert the handle lock pin to secure the handle

before moving.

NOTE: To help keep the handle lock pin securely in the

hole, push the joined area of the lanyard toward the inside

of the generator frame.

 With your foot on the rear of the frame, tilt the machine

toward you until it balances on the wheels, then roll the

machine to the desired location.

LIFTING THE GENERATOR

See Figure 14.

 Turn off the generator.

 Fold the handle to the down position. Never lift or carry

this product using the handle.

NOTE: This tool is heavy and requires several people to

lift. To avoid back injury, keep your knees bent and lift

with your legs, not your back, and get help when needed.

HIGH ALTITUDE OPERATION

Specific modifications are needed for high-altitude operation

for equipment operating in altitudes greater than 3000 feet

above sea level. Please contact your authorized service cen-

ter for important information regarding these modifications.

Operating this engine without the proper altitude modifica-

tion may increase the engine’s emissions and decrease fuel

economy and performance.

OPERATION

Page 15 — English

WARNING:

When servicing, use only identical replacement parts.

Use of any other parts can create a hazard or cause

product damage.

Only the parts shown on the parts list are intended to be

repaired or replaced by the customer. All other parts should

be replaced at an authorized service center.

GENERAL MAINTENANCE

Keep the generator in a clean and dry environment where it

is not exposed to dust, dirt, moisture, or corrosive vapors.

Do not allow the cooling air slots in the generator to become

clogged with foreign material such as leaves, etc.

Do not use a garden hose to clean the generator. Water en-

tering the fuel system or other internal parts of the unit can

cause problems that will decrease the life of the generator.

To clean the unit:

 Use a soft bristle brush and/or vacuum cleaner to loosen

and remove dirt and debris.

 Clean air vents with low pressure air that does not exceed

25 psi.

 Wipe the exterior surfaces of the generator with a damp

cloth.

CHECKING/CLEANING AIR FILTER

See Figure 15.

For proper performance and long life, keep air filter clean.

 Loosen the screw on the bottom of the air filter cover.

Remove cover and set aside.

 Remove the filter element.

 If the filter element is dirty, clean with warm, soapy water.

Rinse and let dry.

 Apply a light coat of engine lubricant to the element, then

squeeze it out.

 Replace the element in the air filter unit.

 Replace the air filter cover and tighten screw to secure.

NOTE: Do not run the generator without the air filter. Rapid

engine wear will result.

CHANGING ENGINE LUBRICANT

See Figure 16.

 Remove the oil cap/dipstick.

 Place a container underneath the oil drain plug to collect

used lubricant as it drains.

 Unscrew the oil drain plug and remove.

 Allow lubricant to drain completely.

NOTE: Drain the lubricant while the engine is still warm

but not hot. Warm lubricant will drain quickly and more

completely.

WARNING:

Do not change engine lubricant while it is hot. Accidental

contact with hot engine lubricant could result in serious

burns.

 Reinstall the oil drain plug and tighten securely.

 Refill with lubricant following the instructions in the

Checking/Adding Lubricant section. For amount of

lubricant needed to refill, see Product Specifications

earlier in this manual or the accompanying engine manual,

if applicable.

 Reinstall the oil cap/dipstick.

NOTE: Used lubricant should be disposed of at an approved

disposal site. See your local oil retailer for more information.

SPARK PLUG MAINTENANCE

See Figure 17.

The spark plug must be properly gapped and free of deposits

in order to ensure proper engine operation. To check:

 Remove the spark plug cap.

 Clean any dirt from around base of spark plug.

 Remove spark plug using wrench (not included).

 Inspect spark plug for damage, and clean with a wire

brush before reinstalling. If insulator is cracked or chipped,

spark plug should be replaced.

NOTE: For replacement spark plug, see Product Specifi-

cations earlier in this manual or the accompanying engine

manual, if applicable.

 Measurepluggap.Thecorrectgapis0.028−0.031in.

(0.7-0.8 mm). To widen gap, if necessary, carefully bend

the ground (top) electrode. To lessen gap, gently tap

ground electrode on a hard surface.

 Seat spark plug in position; thread in by hand to prevent

cross-threading.

 Tighten with wrench to compress washer. If spark plug

is new, use 1/2 turn to compress washer appropriate

amount. If reusing old spark plug, use 1/8 to 1/4 turn for

proper washer compression.

NOTE: An improperly tightened spark plug will become

very hot and could damage the engine.

MAINTENANCE

Page 16 — English

CLEANING THE EXHAUST PORT AND

MUFFLER

Depending on the type of fuel used, the type and amount of

lubricant used, and/or your operating conditions, the exhaust

port and muffler may become blocked with carbon deposits.

If you notice a power loss with your gas-powered products,

you may need to remove these deposits to restore perfor-

mance. We highly recommend that only qualified service

technicians perform this service.

SPARK ARRESTOR

See Figure 18.

 Inspect the spark arrestor for breaks or holes. Re-

place if necessary. To purchase a replacement spark

arrestor contact Powerstroke customer service at

1-877-617-3501.

 Use a brush to remove carbon deposits from the spark

arrestor screen as needed.

DRAINING FUEL TANK/CARBURETOR

See Figures 19 - 21.

To help prevent gum deposits in the fuel system, drain the

fuel from the tank and carburetor before storing.

DRAINING THE FUEL TANK:

 Turn off the generator.

 Turn the fuel valve to the OFF position.

 Push the fuel valve knob through the generator housing

and pull down slightly to gain access to the petcock.

 Remove the fuel line from the petcock by squeezing the

ends of the retaining clip and sliding the fuel line off.

 Install one end of a drain line over the petcock, and place

the other end in a fuel container large enough to catch

the fuel being drained from the tank.

 Turn the fuel valve to the ON position.

 When the fuel has drained from the tank, close the fuel

valve and reinstall fuel line securely on petcock.

 Reinstall fuel valve knob in generator housing. Push for-

ward until knob snaps securely into position.

DRAINING THE CARBURETOR:

 Turn off the generator.

 Turn the fuel valve to the OFF position.

 Position a suitable container under the carburetor drain

screw to catch fuel; loosen the screw.

 Allow fuel to drain completely into container.

 Retighten drain screw.

NOTE: Consult hazardous waste management guidelines in

your area for the proper way to dispose of used fuel.

REPLACING FUEL FILTER

See Figure 22.

Occasionally the fuel filter may become clogged and need

replacing. To purchase a replacement fuel filter contact

Powerstroke customer service at 1-877-617-3501.

NOTE: Fuel tank must be empty before replacing fuel filter.

Run unit until tank is empty, if needed, or inspect filter prior

to fill-up.

 Turn the fuel valve to the OFF position.

 Push the fuel valve knob through the generator housing

and pull down slightly to gain access to the filter.

 Remove the fuel line from both sides of the filter by

squeezing the ends of the retaining clip with pliers.

 Slide the fuel line off.

 Replace with new fuel filter.

 Reinstall fuel lines to new fuel filter.

 Reinstall fuel valve knob in generator housing. Push for-

ward until knob snaps securely into position.

 Turn the fuel valve to the ON position.

TRANSPORTING

 Turn off the generator.

 Turn the fuel valve to the OFF position.

 Make sure engine and exhaust of unit is cool.

 Empty the fuel tank.

 Do not drop or strike unit or place under heavy objects.

MAINTENANCE

Page 17 — English

MAINTENANCE

MAINTENANCE SCHEDULE

NOTE: If a separate engine manual is provided for this generator, please follow the maintenance schedule provided in the en-

gine manual instead of the maintenance information listed below.

Before

each use

After 1st month

or 20 hours of

operation

Every 3 months

or 50 hours of

operation

Every 6 months

or 100 hours

of operation

Every year or

after 300 hours

of operation

Check Engine Lubricant 

Change Engine Lubricant2 

Check Air Filter 

Clean Air Filter 

Change Air Filter2

Check/Adjust Spark Plug 

Replace Spark Plug2

Check/Adjust Idle Speed 

Check/Adjust Valve

Clearance1,2 

Clean Fuel Tank and Filter1,2 

Check Fuel Hose  

Fuel Filter Inspect Replace

Check All Hose

Connections  

Inspect Fuel Tank Vapor

Vent (If Equipped)  

Inspect Carbon Canister

(CARB Models Only)  

1. These items should only be carried out by an authorized service center.

2. See engine manual for maintenance schedule for this item.

NOTE: Maintenance should be performed more frequently when generator is used in dusty areas.

When generator has exceeded the maximum figures specified in the table, maintenance should still be cycled according

to the intervals of time or hours stated herein.

STORAGE

When preparing the generator for storage, allow the unit to cool completely then follow the guidelines below.

STORAGE TIME PRIOR TO STORING

Less than 2 months  Drain gasoline from tank and dispose of in a suitable container according to state and local ordinances.

2 months to 1 year  Drain fuel from carburetor.

 Drain gasoline from tank and dispose of in a suitable container according to state and local ordinances.

1 year or more  Drain fuel from the carburetor.

 Remove spark plug.

 Drain gasoline from tank and dispose of in a suitable container according to state and local ordinances.

 Put a tablespoon of engine lubricant into the spark plug cylinder. Turn the engine slowly with the pull

rope to distribute the lubricant.

 Reinstall spark plug.

 Change engine lubricant.

After removal from storage:

 Fill with fresh gasoline.

NOTE: If storing gasoline in suitable container for later use, make sure gasoline has been treated with fuel stabilizer

according to stabilizer manufacturer’s instructions.

Page 18 — English

PROBLEM POSSIBLE CAUSE SOLUTION

Engine will not start. No fuel.

Stale gasoline or water in gasoline.

Lubricant level is low.

Fuel valve is OFF.

Spark plug faulty, fouled, or improperly

gapped.

Choke lever is in RUN position.

Engine stored without treating or

draining gasoline, or refueled with bad

gasoline.

Dirty fuel filter.

Fill fuel tank.

Drain entire system and refill with fresh

fuel.

Engine is equipped with Low Oil Shutoff.

If engine lubricant level is low, it must be

filled before unit will start. Check engine

lubricant level and fill, if necessary.

Turn fuel valve ON.

Replace spark plug.

Move choke lever to START position.

Drain fuel and carburetor. Refuel with

fresh gasoline.

Replace fuel filter or contact authorized

service center.

Engine hard to start Water in gasoline.

Weak spark at spark plug.

Drain entire system and refill with fresh

fuel.

Replace spark plug or contact

authorized service center.

Engine lacks power. Dirty air filter.

Engine stored without treating or

draining gasoline, or refueled with bad

gasoline.

Check air filter element. Clean or replace

as needed.

Drain fuel and carburetor. Refuel with

fresh gasoline. If problem continues,

contact your nearest authorized service

center.

AC receptacle does not work. Circuit breaker is OFF.

Item plugged in is defective.

Turn ON the AC circuit breaker.

Try a different item.

Generator makes a “spark knock” or

“pinging” noise.

An occasional light “knocking” or “ping-

ing” under heavy load is not a cause for

concern. However, if the knocking or

pinging occurs under normal load at a

steady engine speed, the problem may

be with the brand of gasoline being used.

Switch to a different brand of gasoline,

making sure that the octane rating is 86

or higher. If problem continues, contact

your nearest authorized service center.

If problem persists after trying the above solutions, contact your nearest authorized service center for assistance.

The following symptoms may indicate problems that will affect the emissions level of the unit:

 Hard starting or stalling after starting

 Rough idle

 Misfiring or backfiring under load

 Afterburning (backfiring)

 Black exhaust smoke or high fuel consumption

If you encounter any of these symptoms, have the unit inspected and repaired by the nearest authorized service center.

TROUBLESHOOTING

Page 19 — English

WARRANTY

LIMITED NON-ENGINE WARRANTY STATEMENT

OWT Industries, Inc., (the Company) warrants to the original retail purchaser that this PowerStroke Product is free

from defects in material and workmanship and agrees to repair or replace, at the Company’s discretion, any defective

Product free of charge within these time periods from the date of purchase:

 Three years, if the Product is used solely for personal, family, or household use;

 One year, if the Product is used for business or commercial use.

This warranty applies only to Products sold within the United States of America, the District of Columbia, Canada,

Mexico, the Commonwealth of Puerto Rico, the Virgin Islands, or Guam.

This warranty is not transferable and does not cover damage resulting from defects other than in material or workman-

ship, or damage caused by unreasonable use, including the failure to provide reasonable and necessary maintenance.

Other items not covered under this warranty include:

 Transportation charges for sending the product to the Company or its authorized service representative for warranty

service, or for shipping repaired or replacement products back to the customer; these charges must be borne by

the original retail purchaser.

 Damages caused by abuse, accident, misuse, neglect, alteration, modification, the effects of corrosion, erosion,

normal wear and tear or repairs by other than the Company or its authorized service representative.

 In addition this warranty does not cover:

 Tune-ups – Spark Plugs, Carburetor, Carburetor Adjustments, Ignition, Filters, Oil Change

 Wear items – Recoil Starter Rope, Engine Brushes, Cotter Pins, Wheels

Warranty is voided if the customer fails to install, maintain and operate the product in accordance with the instruc-

tions and recommendations of the Company as set forth in the Product’s operator’s manual or if the Product is used

as rental equipment.

The Company will not pay for repairs or adjustments to the Product, or for any costs or labor, performed without the

Company’s prior authorization.

SAVE YOUR SALES SLIP

Proof of purchase in the form of your dated sales receipt, cash register slip, etc., will be required before the Company

and/or its authorized service representatives can perform warranty service on the Product.

EXCLUSIONS AND LIMITATIONS

THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. ANY IMPLIED WARRANTY OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR OTHERWISE, APPLICABLE TO THIS PRODUCT,

SHALL BE LIMITED IN DURATION TO THE DURATION OF THIS LIMITED WARRANTY. THE WARRANTY SERVICE

DESCRIBED ABOVE IS THE EXCLUSIVE REMEDY UNDER THIS WARRANTY. THE COMPANY SHALL NOT BE LIABILE

FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES.

SOME STATES DO NOT ALLOW A LIMITATION ON THE DURATION OF IMPLIED WARRANTIES, OR THE EXCLUSION

OR LIMITATION OF INCIDENTAL, OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION

MAY NOT APPLY TO YOU.

HOW TO OBTAIN WARRANTY SERVICE

For warranty service: Call toll free 1-877-617-3501, or write to OWT Industries, Inc., P.O. Box 35, Hwy. 8, Pickens,

SC 29671.

For warranty service outside the USA, please contact your local PowerStroke dealer.

Page 20 — English

WARRANTY

CHONGQING RATO POWER MANUFACTURING CORPORA-

TION (RATO), warrants that each new engine sold by it will be

free, under normal use and service, from defects in material

and workmanship for a period listed below from the date of

sale to the original retail purchaser. RATO’s obligation under

this Limited Warranty shall be limited to the repair and re-

placement, at RATO’s option, of any part or parts which upon

examination is/are found, in RATO’s judgment, to have been

defective in material or work manship. It shall be a condition

of RATO’s obligation under this Limited Warranty that RATO,

directly or through one of its Distributors or Service Centers

authorized to service the particular engine involved, receive

prompt notice of any warranty claim and that the engine or

the part or parts claimed to be defec tive be promptly deliv-

ered, transportation prepaid, to such Distributor or Service

Center for inspection and repair. All repairs qualifying under

this Limited Warranty must be performed by RATO or one of

its autho rized Distributors or Service Centers.

WARRANTY PERIOD: Two (2) year limited engine warranty.

If you have a question regarding your warranty coverage, call

1-866-340-3912.

The repair or replacement of any part or parts under this Lim-

ited Warranty shall not extend the term of the engine warranty

beyond the original term as set forth above.

LIMITATIONS AND EXCLUSIONS: This Limited Warranty

shall not apply to:

1. Bent or broken crankshaft or resultant damage caused

by vibration related to a bent or broken crankshaft

Also, damage caused by loose engine mounting bolts or

improper or imbalanced accessories or blades mounted

to the crankshaft.

2. Repairs required because of prolonged storage including

damage caused by old or contami nated fuel in the fuel

tank, fuel lines, or carburetor, sticky valves or corrosion

and rust of engine parts.

3. Repair required due to overheating. (Most often caused

by overloaded or clogged or damaged or missing

flywheel, fan, inlet air passages, cooling fins, or air

shrouds.)

4. Dirt or grit related wear caused by improper air cleaner

maintenance (most often resulting in worn piston, piston

rings, cylinders, valves, valve guides, carburetor, or

other internal compo nents).

5. Broken or scored parts caused by low lubricant level,

dirty, or improper grade of lubricant.

6. Engine tune-ups and normal maintenance service

including, but not limited to, valve adjust ment, normal

replacement of service items, fuel, and lubricating oil,

etc.

7. Any engine which has been subject to negligence,

misuse, accident, misapplication, or overspeeding.

8. Any engine that has been installed, repaired, or altered

by anyone in a manner which in RATO’s sole judgment

adversely affects its performance or reliability.

9. Any engine which has been fitted with or repaired with

parts or components not manufactured or approved by

RATO which in RATO’s sole judgment adversely affects

its performance or reli ability.

10. Instances when normal use has exhausted the life of

a component or an engine.

The customer is responsible for all transportation charges in

connection with any warranty work.

RATO reserves the right to modify, alter, or improve any

engines or parts without incurring any oblig ation to modify

or replace any engine or parts previously sold without such

modification, alternation, or improvement.

No person is authorized to give any other warranty or to as-

sume any additional obligation on RATO’s behalf unless made

in writing and signed by an officer of RATO.

THIS WARRANTY, AND RATO’S OBLIGATION HERE UNDER,

ARE IN LIEU OF ANY OTHER WARRANTIES OR OBLIGATIONS

OF ANY KIND, EXPRESSED OR IMPLIED, INCLUDING ANY

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR

A PARTICULAR PURPOSE. THERE ARE NO WARRANTIES

WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE

HERE-OF. RATO SHALL IN NO EVENT BE LIABLE FOR ANY

CONSEQUENTIAL OR INCIDENTAL DAMAGES.

LIMITED ENGINE WARRANTY

Page 21 — English

WARRANTY

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The United States Environmental Protection Agency (EPA) and Chongqing RATO

Power Manufacturing Corporation (RATO), are pleased to explain the emission

control system warranty on your small off-road engine. In the United States except

California, new small off-road engines must be designed, built and equipped to

meet the State’s stringent anti smog standards. RATO must warrant the emission

control system on your small off-road engine for the periods of time listed below

provided there has been no abuse, neglect or improper maintenance of your small

off-road engine.

Your emission control system may include parts such as the carburetor or fuel

injection system, the ignition system, and catalytic converter. Also included may

be hoses, belts, connectors and other emission related assemblies.

Where a warrantable condition exists, RATO will repair your small off-road engine

at no cost to you including diagnosis, parts and labor.

MANUFACTURER’S WARRANTY COVERAGE:

Emissions Control System is warranted for two years on small off-road engine. If

any emission related part on your engine is defective, the part will be repaired or

replaced by RATO. RATO provides warranty coverage for a period of two years.

OWNER’S WARRANTY RESPONSIBILITIES:

As the small off-road engine owner, you are responsible for the performance of the

required maintenance listed in your owner’s manual. RATO recommends that you

retain all receipts covering maintenance on your small off-road engine, but RATO

cannot deny warranty solely for the lack of receipts or for your failure to ensure the

performance of all scheduled maintenance.

As the small off-road engine owner, you should however be aware that RATO may

deny you warranty coverage if your small off-road engine or a part has failed due

to abuse, neglect, improper maintenance or unapproved modifications.

You are responsible for presenting your small off-road engine to a RATO distribution

center as soon as a problem exists. The warranty repairs should be completed in

a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you

should contact 1-866-340-3912 or www.powerstroketools.com.

DEFECTS WARRANTY REQUIREMENTS:

(a) The warranty period begins on the date the engine or equipment is delivered to

an ultimate purchaser.

(b) General Emissions Warranty Coverage. RATO warrants to the ultimate purchaser

and each subsequent owner that the engine or equipment is:

(1) Designed, built, and equipped so as to conform with all applicable regulations

adopted by the Air Resources Board and the United States Environmental

Protection Agency (U.S.EPA);

(2) Free from defects in materials and workmanship that causes the failure of

a warranted part for a period of two years.

(1) Any warranted part that is not scheduled for replacement as required mainte-

nance in the written instructions required by subsection (d) must be warranted

for the warranty period defined in Subsection (b)(2). If any such part fails

during the period of warranty coverage, it must be repaired or replaced by

RATO according to Subsection (4) below. Any such part repaired or replaced

under the warranty must be warranted for the remaining warranty period.

(2) Any warranted part that is scheduled only for regular inspection in the written

instructions required by subsection (d) must be warranted for the warranty

period defined in Subsection (b)(2). A statement in such written instructions

to the effect of “repair or replace as necessary” will not reduce the period

of warranty coverage. Any such part repaired or replaced under warranty

must be warranted for the remaining warranty period.

(3) Any warranted part that is scheduled for replacement as required mainte-

nance in the written instructions required by subsection (d) must be warranted

for the period of time prior to the first scheduled replacement point for that

part. If the part fails prior to the first scheduled replacement, the part must

be repaired or replaced by RATO according to Subsection (4) below. Any

such part repaired or replaced under warranty must be warranted for the

remainder of the period prior to the first scheduled replacement point for

the part.

(4) Repair or replacement of any warranted part under the warranty must be

performed at no charge to the owner at a warranty station.

(5) Notwithstanding the provisions of Subsection (4) above, warranty services or

repairs must be provided at all RATO distribution centers that are franchised

to service the subject engines.

(6) The owner must not be charged for diagnostic labor that leads to the

determination that a warranted part is in fact defective, provided that such

diagnostic work is performed at a warranty station.

(7) RATO is liable for damages to other engine components proximately caused

by a failure under warranty of any warranted part.

(8) Throughout the emissions warranty period defined in Subsection (b)(2), RATO

must maintain a supply of warranted parts sufficient to meet the expected

demand for such parts.

(9) Any replacement part may be used in the performance of any warranty

maintenance or repairs and must be provided without charge to the owner.

Such use will not reduce the warranty obligations of RATO.

(10) Add-on or modified parts that are not exempted by the Air Resources Board

may not be used. The use of any non-exempted add-on or modified parts

will be grounds for disallowing a warranty claim. RATO will not be liable to

warrant failures of warranted parts caused by the use of a non-exempted

add-on or modified part.

(11) RATO issuing the warranty shall provide any documents that describe that

manufacturer’s warranty procedures or policies within five working days of

request by the Air Resources Board.

(d) Emission Warranty Parts List.

(1) Fuel Metering System

(i) Carburetor and internal parts (and/or pressure regulator or fuel injection

system).

(ii) Air/fuel ratio feedback and control system.

(iii) Cold start enrichment system.

(iv) Fuel Tank.

(2) Air Induction System

(i) Controlled hot air intake system.

(ii) Intake manifold.

(iii) Air filter.

(3) Ignition System

(i) Spark Plugs.

(ii) Magneto or electronic ignition system.

(iii) Spark advance/retard system.

(4) Exhaust Gas Recirculation (EGR) System

(i) EGR valve body, and carburetor spacer if applicable.

(ii) EGR rate feedback and control system.

(5) Air Injection System

(i) Air pump or pulse valve.

(ii) Valves affecting distribution of flow.

(iii) Distribution manifold.

(6) Catalyst or Thermal Reactor System

(i) Catalytic converter.

(ii) Thermal reactor.

(iii) Exhaust manifold.

(7) Particulate Controls

(i) Traps, filters, precipitators, and any other device used to capture particulate

emissions.

(8) Miscellaneous Items Used in Above Systems

(i) Electronic controls.

(ii) Vacuum, temperature, and time sensitive valves and switches.

(iii) Hoses, belts, connectors, and assemblies.

EMISSION CONTROL WARRANTY STATEMENT

Page 22 — English

WARRANTY

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The U.S. EPA, Environment Canada, and OWT Industries, Inc.,

are pleased to explain the evaporative emission control system’s

warranty on your small off-road equipment. New equipment that

uses small off-road engines must be designed, built, and equipped

to meet the stringent evaporative standards. OWT Industries, Inc.,

must warrant the evaporative emission control system on your

small off-road equipment for the period listed below, provided

there has been no abuse, neglect or improper maintenance of

your equipment.

Your evaporative emission control system may include parts such

as: carburetors, fuel tanks, fuel line, fuel caps, valves, canisters,

filters, vapor hoses, clamps, connectors, and other associated

components.

MANUFACTURER’S WARRANTY COVERAGE:

This evaporative emission control system is warranted for three

years. If any evaporative emission-related part on your equipment is

defective, the part will be repaired or replaced by OWT Industries, Inc.

OWNER’S WARRANTY RESPONSIBILITIES:

 As the small off-road equipment owner, you are responsible

for performance of the required maintenance listed in your

operator’s manual. OWT Industries, Inc., recommends that you

retain all receipts covering maintenance on your small off-road

equipment, but OWT Industries, Inc., cannot deny warranty

solely for the lack of receipts.

 As the small off-road equipment owner, you should, however,

be aware that OWT Industries, Inc., may deny you warranty

coverage if your small off-road equipment or a part has failed

due to abuse, neglect, or improper maintenance or unapproved

modifications.

 You are responsible for presenting your small off-road equip-

ment to a OWT Industries, Inc., distribution center or service

center as soon as the problem exists. The warranty repairs

should be completed in a reasonable amount of time, not to

exceed 30 days.

If you have a question regarding your warranty coverage, you

should contact OWT Industries, Inc., at 1-877-617-3501or

www.powerstroketools.com.

DEFECTS WARRANTY REQUIREMENTS:

(a) The warranty period begins on the date the equipment is de-

livered to an ultimate purchaser.

(b) General Evaporative Emissions Warranty Coverage. The equip-

ment must be warranted to the ultimate purchaser and any

subsequent owner that the evaporative emission control system

when installed was:

(1) Designed, built, and equipped so as to conform with all

applicable regulations; and

(2) Free from defects in materials and workmanship that cause

the failure of a warranted part for a period of three years.

interpreted as follows:

(1) Any warranted part that is not scheduled for replacement

as required maintenance in the written instructions must be

warranted for the warranty period defined in subsection (b)

(2). If any such part fails during the period of warranty cov-

erage, it must be repaired or replaced by the manufacturer

issuing the warranty. Any such part repaired or replaced

under the warranty must be warranted for a time not less

than the remaining warranty period.

(2) Any warranted part that is scheduled only for regular in-

spection in the written instructions must be warranted for

the warranty period defined in subsection (b)(2). A state-

ment in such written instructions to the effect of “repair or

replace as necessary” will not reduce the period of war-

ranty coverage. Any such part repaired or replaced under

warranty must be warranted for a time not less than the

remaining warranty period.

(3) Any warranted part that is scheduled for replacement as

required maintenance in the written instructions must be

warranted for the period of time prior to the first scheduled

replacement point for that part. If the part fails prior to the

first scheduled replacement, the part must be repaired or

replaced by the manufacturer issuing the warranty. Any

such part repaired or replaced under warranty must be

warranted for a time not less than the remainder of the

period prior to the first scheduled replacement point for

the part.

(4) Repair or replacement of any warranted part under the

warranty provisions of this article must be performed at

no charge to the owner at a warranty station.

(5) Notwithstanding the provisions of subsection (4) above,

warranty services or repairs must be provided at distri-

bution centers that are franchised to service the subject

equipment.

(6) The owner must not be charged for diagnostic labor that

leads to the determination that a warranted part is in fact

defective, provided that such diagnostic work is performed

at a warranty station.

(7) Throughout the evaporative emission control system’s war-

ranty period set out in subsection (b)(2), the manufacturer

issuing the warranty must maintain a supply of warranted

parts sufficient to meet the expected demand for such

parts.

(8) Manufacturer approved replacement parts must be used

in the performance of any warranty maintenance or repairs

and must be provided without charge to the owner. Such

use will not reduce the warranty obligations of the manu-

facturer issuing the warranty.

(9) The use of any add-on or modified parts will be grounds

for disallowing a warranty claim made in accordance with

this article. The manufacturer issuing the warranty will not

be liable under this Article to warrant failures of warranted

parts caused by the use of an add-on or modified part.

EMISSION WARRANTY PARTS LIST:

1) Fuel Tank

2) Fuel Cap

3) Fuel Line

4) Carbon Canister

5) Vapor Hoses

6) Hose Clamps

7) Hose Connectors

8) Vapor/Fuel Check Valve

Written instructions for the maintenance and use of the evapora-

tive emissions control system by the owner shall be furnished

with all new small off-road equipment.

OWT INDUSTRIES, INC., FEDERAL EMISSION CONTROL WARRANTY STATEMENT

Page 23 — English

NOTES

Page 2 — Français

 Introduction .................................................................................................................................................................... 2

 Instructions importantes concernant la sécurité ........................................................................................................3-4

 Règles de sécurité particulières ..................................................................................................................................... 4

 Symboles ....................................................................................................................................................................5-7

 Caractéristiques électriques .......................................................................................................................................8-9

 Caractéristiques .......................................................................................................................................................... 10

 Assemblage ............................................................................................................................................................11-12

 Utilisation ................................................................................................................................................................12-14

 Entretien .................................................................................................................................................................. 15-17

 Dépannage ................................................................................................................................................................... 18

 Garantie ..................................................................................................................................................................19-22

 Commande de pièces / réparation ...............................................................................................................Páge arrière

Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et plus satisfaisante. Lors de la

conception de ce produit, l’accent a été mis sur la sécurité, les performances et la fiabilité, afin d’en faire un outil facile à

utiliser et à entretenir.

DANGER :

MISE À LA TERRE DU GÉNÉRATEUR

Pour réduire les risques de choc électrique ou d’électrocution, le générateur doit être

correctement mis à la terre. L’écrou et la borne de terre sur le cadre doivent toujours

être utilisés pour connecter le générateur à une source de terre adaptée. La mise à

la terre doit se faire avec un fil de calibre 8. Brancher la borne du fil de terre entre la

rondelle de blocage et l’écrou, puis bien serrer l’écrou. Brancher l’autre extrémité du

fil à une source de terre adaptée.

Le code électrique américain contient diverses façons pratiques permettant d’établir

une bonne source de terre. Si une tige en fer ou en acier est utilisée, elle doit être

d’au moins 15 mm (5/8 po) et si une tige non ferreuse est utilisée, elle doit avoir un

diamètre d’au moins 12,5 mm (1/2 po) et être faite d’un matériau indiqué pour la

mise à la terre. Introduire la tige ou le fourreau à une profondeur de 2,4 m (8 pieds).

Si un fond rocailleux est présent à moins de 1,2 m (4 pieds), enterrer la tige ou le

fourreau dans une tranchée.

Tous les outils et les appareils électriques utilisés à l’aide de ce générateur doivent être

correctement mis à la terre par l’intermédiaire d’un troisième fil ou être doublement

isolés.

Il est recommandé :

1. d’utiliser des appareils électriques avec prises de terre à trois fiches.

2. d’utiliser un cordon prolongateur conçus pour l’extérieur avec prise à 3 pôles et une fiche à 3 broches aux extrémités

opposées pour assurer la continuité de la protection de mise à la terre du générateur à l’appareil.

Consulter et respecter tous les réglements nationaux et locaux applicables concernant les spécifications de mise à la

terre. Consulter un électricien qualifié ou le personnel de service si les instructions de mise à la terre ne sont pas bien

comprises, ou en cas de doute au sujet de la mise à la terre.

TABLE DES MATIÈRES

INTRODUCTION

Page 3 — Français

INSTRUCTIONS IMPORTANTES CONCERNANT LA SÉCURITÉ

DANGER :

Monoxyde de Carbone. Utiliser une génératrice à l’intérieur

d’un bâtiment CAUSERA LA MORT EN QUELQUES

MINUTES.

Le tuyau d’échappement de la génératrice contient un

niveau élevé de monoxyde de carbone (CO), lequel s’avère

être un gaz poison inodore et invisible. Si vous pouvez sentir

les gaz du tuyau d’échappement de la génératrice, vous

respirez du CO. Mais, même si vous ne pouvez pas sentir

les gaz provenant du tuyau d’échappement, vous pourriez

être en train de respirer du CO.

 Ne jamais utiliser une génératrice à l’intérieur d’une

maison, des garages, des petits espaces, ou autres aires

restreintes partiellement fermées. Des niveaux mortels

de monoxyde de carbone peuvent s’accumuler dans

ces aires restreintes. Utiliser un ventilateur ou ouvrir une

fenêtre ou les portes NE fournie PAS assez d’air frais à

respirer.

 Utilisez SEULEMENT la génératrice à l’extérieur et loin

des fenêtres ouvertes, des portes ouvertes, et des

bouches d’aérations. Ces ouvertures peuvent tirer l’air

provenant du tuyau d’échappement.

Même si vous utilisez une génératrice correctement, des gaz

CO peuvent toujours s’infiltrer dans la maison. TOUJOURS

utiliser une alarme de monoxyde de carbone à piles dans

votre maison.

Si vous ressentez que vous commencez à être étourdi ou

faible suite au fonctionnement de la génératrice, allez prendre

l’air frais IMMÉDIATEMENT. Consultez un médecin. Vous

pourriez avoir un empoisonnement au monoxyde de carbone.

AVERTISSEMENT :

Lire et comprendre toutes les instructions. Le non-respect

de toutes les instructions ci-dessous peut entraîner une

électrocution, un incendie et/ou un empoisonnement au

monoxyde de carbone, pouvant causer des blessures

graves, voire mortelles.

DANGER :

Le code électrique américain (National Electric Code) requiert

que le générateur soit mis à la terre par l’intermédiaire d’une

source de terre approuvée. Avant d’utiliser la borne de terre,

consulter un électricien qualifié, un inspecteur en électricité ou

un organisme local connaissant les codes et les réglements

locaux applicables à l’utilisation prévue du générateur.

CONSERVER CES INSTRUCTIONS

Ce manuel relate à propos d’instructions importantes lesquelles

devraient être suivies pendant l’installation et l’entretien des

piles et de la génératrice.

 Ne pas brancher au circuit électrique d’un bâtiment à moins

que la génératrice et le commutateur de transfert n’aient

été installés correctement par un électricien qualifié, et que

ce dernier n’ait vérifié la sortie électrique. Le branchement

doit isoler l’alimentation de la génératrice de la source

d’alimentation de l’appareil et doit répondre à toutes les lois

et codes de l’électricité applicables.

 Ne pas laisser des enfants ou personnes n’ayant pas reçu

une formation adéquate utiliser cette unité.

 Ne pas démarrer ou faire tourner le moteur dans un espace

confine, de bâtiment, à proximité des fenêtres ouverts, autre

ou des zones sans ventilation où des vapeurs toxiques de

monoxyde de carbone peuvent s’accumuler. Le monoxyde

de carbone, un gaz incolore, inodore et extrêmement toxique

peut causer une perte de conscience et être mortel.

 Garder les badauds, enfants et animaux domestiques à une

distance minimum de 3 m (10 pi).

 Porter des chaussures ou des bottes robustes et sèches.

Ne pas utiliser pieds nus.

 Ne pas utiliser le générateur en état de fatigue, si l’on est

souffrant ou sous l’influence de l’alcool, de drogues ou de

médicaments.

 Garder toutes les parties du corps à l’écart des pièces en

mouvement et des parties brûlantes de l’outil.

 Ne pas toucher les prises ou les fils dénudés.

 Ne pas utiliser le générateur avec des cordons électriques

usés, effilochés, dénudés ou autrement endommagés.

 Laisser le moteur refroidir avant de remiser l’outil et vidanger

le carburant.

 Ne pas utiliser le générateur dans la pluie ou la neige.

 Remiser la génératrice dans un endroit bien ventilé après

avoir vider le réservoire de carburant. Ne pas remiser le

carburant à proximité de la génératrice.

 Pour le transport dans un véhicule, le réservoir doit être vide,

le robinet de carburant fermé et la machine bien arrimée.

 Laisser le moteur refroidir pendant 5 minutes avant de faire

le plein.

 Manipuler le carburant avec précaution pour éviter les risques

d’incendies et de brûlures. Le carburant est extrêmement

inflammable.

 Ne pas fumer pendant la manipulation du carburant.

 Conserver le carburant dans un bidon ou jerrican approuvé

pour l’essence.

 Poser la machine sur un sol plat, arrêter le moteur et le laisser

refroidir avant de faire le plein.

 Desserrer le bouchon du réservoir lentement pour relâcher

la pression et éviter que le carburant ne s’échappe.

 Une fois le réservoir plein, remettre le bouchon en place et

le serrer fermement.

 Essuyer tout le carburant éventuellement répandu.

 N’essayer en aucun cas de brûler le carburant répandu.

 Une vibration est normale pendant l’utilisation de la génératrice.

Pendant et après l’utilisation de la génératrice, inspectez celle-

ci, tout comme les câbles d’extension et les câbles branchés

à la boîte d’alimentation afin de détecter tout bris potentiel

du matériel. Faites réparer tout dommage immédiatement

ou remplacer les pièces endommagées au besoin. Ne pas

utiliser de fiches ou des câbles qui sont endommagés tels

qu’ils aient des signes de fissures ou si la couche isolante

est craquée ou si les lamelles sont endommagées.

Page 4 — Français

INSTRUCTIONS IMPORTANTES CONCERNANT LA SÉCURITÉ

RÈGLES DE SÉCURITÉ PARTICULIÈRES

 Il est préférable d’utiliser une génératrice fixe comme

source d’énergie de secours pour alimenter la maison en

cas de panne d’électricité. Une génératrice portative, même

correctement branchée, risque une surcharge. Il peut en

résulter une surchauffe ou une contrainte indue sur les

composantes du génératrice, ce qui peut provoquer une

défaillance de la génératrice.

 Utiliser uniquement des pièces de rechange et des

accessoires approuvés et suivre les instructions dans la

section Entretien de ce manuel. L’usage de pièces non

autorisées ou le non-respect des instructions peut présenter

des risques de choc électrique ou de blessures.

 Entretenir le produit conformément aux instructions de ce

manuel d’utilisation.

 Inspecter le produit avant chaque utilisation pour s’assurer

qu’il n’y a pas de pièces desserrées, de fuites de carburant,

etc. Remplacer les pièces endommagées.

AVERTISSEMENT :

Lorsque cette génératrice est utilisée pour fournir

de l’énergie à un système électrique d’un bâtiment :

cette génératrice doit être installée par un électricien

qualifié et doit être branchée à un circuit fermé muni d’un

interrupteur de transfert, conformément au Code National

Électrique NFPA70. La génératrice devra être branchée sur

un interrupteur de transfert lequel pourra allumer tous les

conducteurs autres que celui du circuit électrique principal.

Le cadre de la génératrice doit être mis à la terre par

l’intermédiaire d’une source de terre approuvée. Si cette

étape n’est pas faite, la génératrice ne sera pas isolée du

circuit électrique et cela pourrait entraîner des blessures

graves, voire même la mort chez un électricien travaillant

pour l’usine.

 Ne pas utiliser cette génératrice pour alimenter les appareils

d’urgence médicale ou le matériel de survie.

 Cette génératrice est équipée d’un connecteur neutre lié à

la masse. Cela signifie que le conducteur neutre est relié

électriquement au cadre de l’unité.

 L’échappement contient du monoxyde de carbone, un

gaz toxique incolore et inodore. L’inhalation des fumées

d’échappement peut causer la perte de conscience et

le décès. Si la machine tourne dans un endroit clos ou

partiellement clos, l’air peut contenir une quantité dangereuse

de monoxyde de carbone. Pour éviter l’accumulation de

fumées d’échappement, toujours assurer une ventilation

adéquate.

 Toujours utiliser un détecteur de monoxyde de carbone

fonctionnant sur piles lors de l’utilisation du générateur.

En cas de sensation de nausée, d’étourdissement ou de

faiblesse lors de l’utilisation du générateur, l’arrêter et aller

immédiatement à l’air frais. Consulter un docteur. Il peut

s’agir d’un empoisonnement au monoxyde de carbone.

 Placer le générateur sur une surface stable et plate avec une

pente au plus 4 °.

 Utiliser dans un endroit bien ventilé et bien éclairé à l’écart

des zones de travail pour éviter les interférences sonores.

 L’utilisation du générateur dans des conditions mouillées

peut entraîner l’électrocution. Conserver l’unité au sec.

 Garder le générateur à au moins 1 m (3 pieds) de tout type

de matériau combustible.

 Ne jamais utiliser le générateur près de matériaux dangereux.

 Ne pas utiliser le générateur près d’une station de distribution

d’essence ou de gaz naturel.

 Ne pas toucher le silencieux ou le cylindre durant ou

immédiatement après l’utilisation. Ils sont BRÛLANTS et

peuvent provoquer des brûlures.

 Ne pas laisser le réservoir d’essence de la génératrice

déborder lors du remplissage. Remplir le réservoir jusqu’à

25,4 mm (1 po) de l’ouverture du goulot du réservoir pour

permettre l’expansion du carburant. Ne pas recouvrir

le bouchon du réservoir de carburant lorsque le moteur

fonctionne. Ne pas respecter cette directive peut

causer une panne de moteur ou endommager l’outil.

 Ne pas fumer lors du remplissage du générateur avec de

l’essence.

 Fermer le moteur et le laisser refroidir complètement avant

l’ajout de carburant ou la lubrification de la génératrice.

 Ne pas retirer la jauge d’huile ou le bouchon du réservoir de

carburant lorsque le moteur tourne.

 Bien tenir compte de tous les autocollants de sécurité situés

sur le générateur.

 Garder les enfants à un minimum de 3 m (10 pieds) du

générateur à tout moment.

 L’unité fonctionne le mieux à des températures comprises

entre -5 et 40 °C (23 et 104 °F) avec une humidité relative

de 90 % ou moins.

 Vérifier la tension et la fréquence requises avant de brancher

tout équipement électronique sur le générateur. Le générateur

peut se trouver endommagé si les appareils branchés ne sont

pas prévus pour fonctionner à une tension égale à ± 10%

et une fréquence égale à ± 3 hz de celles indiquées sur la

plaque signalétique du générateur. Pour éviter tout dommage,

toujours brancher une charge additionnelle sur le générateur

lorsqu’un appareil à circuits intégrés (tel qu’un téléviseur)

est utilisé. Une varistance peut être aussi nécessaire pour

certaines applications, dans le cas d’un ordinateur, par

exemple. Une varistance peut être aussi nécessaire pour

certaines applications de l’équipement en solide.

 Pour l’utilisation à l’extérieur seulement.

 Conserver ces instructions. Les consulter fréquemment et les

utiliser pour instruire les autres utilisateurs éventuels. Si ce

produit est prêté, il doit être accompagné de ces instructions.

Page 5 — Français

SYMBOLES

Les termes de mise en garde suivants et leur signification ont pour but d’expliquer le degré de risques associé à l’utilisation de ce

produit.

SYMBOLE SIGNAL SIGNIFICATION

DANGER : Indique une situation extrêmement dangereuse qui, si elle n’est pas évitée, aura

pour conséquences des blessures graves, voire mortelles.

AVERTISSEMENT : Indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, aura

pour conséquences des blessures graves ou mortelles.

ATTENTION : Indique une situation potentiellement dangereuse qui, si elle n’est pas évitée,

pourrait entraîner des blessures légères ou de gravité modérée.

AVIS :

(Sans symbole d’alerte de sécurité) Indique une information importante ne

concernant pas un risque de blessure comme une situation pouvant occasionner

des dommages matériels.

Certains des symboles ci-dessous peuvent être utilisés sur produit. Veiller à les étudier et à apprendre leur signification.

Une interprétation correcte de ces symboles permettra d’utiliser produit plus efficacement et de réduire les risques.

SYMBOL NAME DESIGNATION/EXPLANATION

Alerte de sécurité Indique un risque de blessure potentiel.

Lire le manuel d’utilisation Pour réduire les risques de blessures, l’utilisateur doit lire et veiller à bien

comprendre le manuel d’utilisation avant d’utiliser ce produit.

Avertissement concernant

l’humidité Ne pas exposer à la pluie ou l’humidité.

Choc électrique

Une utilisation de l’équipement dans des conditions non sèches et le

non-respect des méthodes sans danger peuvent entraîner un choc

électrique.

Vapeurs toxiques

Durant le fonctionnement, le générateur émet du monoxyde de carbone,

un gaz toxique inodore et incolore. Respirer le monoxyde de carbone peut

entraîner des nausées, des évanouissements, voire la mort.

Incendie/explosion

Le carburant et ses vapeurs sont extrêmement inflammables et explosifs.

Un incendie ou une explosion peut entraîner des brûlures graves, voire

la mort.

Surface chaude Pour éviter les risques de blessures ou de dommages, éviter tout contact

avec les surfaces brûlantes.

Danger au levage Pour réduire le risque de blessures graves, éviter de lever le générateur

seul.

Mise à la terre Consulter un électricien local pour déterminer les exigences de mise à la

terre avant le fonctionnement.

Électrocution Une mauvaise mise à la terre du générateur peut causer une électrocution,

surtout si le générateur est équipé d’un kit de roues.

Page 6 — Français

SYMBOLES

AUTOCOLLANTS DE SÉCURITÉ

 Ne pas procéder de la manière décrite dans ce manuel

d’utilisation entraînera des BLESSURES GRAVES voire

la MORT.

 Risque d’incendie. Ne pas ajouter de carburant pendant

l’utilisation de l’appareil.

 Le générateur est une source potentielle de chocs

électriques. Ne pas exposer à l’humidité, la pluie ou la

neige. Ne pas utiliavec les mains ou les pieds mouillés.

 L’échappement contient le gaz monoxyde de carbone

toxique qui peut causer l’inconscience ou la MORT les

secteurs bien ventilés et extérieurs loin d’ouvre des fenêt

ou des portes.

Certains des symboles ci-dessous peuvent être utilisés sur produit. Veiller à les étudier et à apprendre leur signification.

Une interprétation correcte de ces symboles permettra d’utiliser produit plus efficacement et de réduire les risques.

SYMBOL NAME DESIGNATION/EXPLANATION

AAmpères Courant

Hz Hertz Fréquence (cycles par seconde)

WWatt Puissance

hrs Heures Durée

gal Gallon Volume

qt Quart Volume

DANGER DANGER

PELIGRO

L’utilisation d’une génératrice à l’intérieur PEUT VOUS TUER ENQUELQUES MINUTES.

Les génératrices produisent du monoxyde de carbone, un gaz mortel incolore et inodore.

NE JAMAIS utiliser à l’intérieur d’une maison ou d’un garage,MÊME SI les portes et

les fenêtres sont ouvertes.

Utiliser uniquement À L’EXTÉRIEUR et loin des fenêtres, des portes et des évents.

Usar un generador en el interior PUEDE MATARLO EN POCOS MINUTOS.

Los gases de escape del generador contienen monóxido de carbono. Es un veneno

que no puede verse ni olerse.

NUNCA lo use dentro de su hogar o del garaje, INCLUSO con las puertas y las

ventanas abiertas.

Sólo utilícelo AL AIRE LIBRE y lejos de ventanas, puertas y respiraderos.

Using a generator indoors CAN KILL YOU IN MINUTES.

Generator exhaust contains carbon monoxide. This is a

poison you cannot see or smell.

NEVER use inside a home

or garage, EVEN IF doors

and windows are open.

Only use OUTSIDE and

far away from windows,

doors, and vents.

You WILL be KILLED or SERIOUSLY

HURT if you do not follow the Operator’s

Manual instructions.

Ne pas procéder de la manière décrite

dans ce Manuel d’utilisation entraînera

des BLESSURES GRAVES voire la MORT.

SE MATARÁ o LESIONARÁ GRAVEMENTE

si no sigue las instrucciones del Manual

del operador.

Risk of fire. Do not add fuel while the

product is operating.

Risque d’incendie. Ne pas ajouter de

carburant pendant l’utilisation de

l’appareil.

Riesgo del incendio. No agregue

combustible cuando el producto esté

functionando.

Generator is a potential source of electric

shock. Do not expose to moisture, rain, or

snow. Do not operate with wet hands or feet.

Le générateur est une source potentielle

de chocs électriques. Ne pas exposer à l’humidité,

la pluie ou la neige. Ne pas utiliser avec les

mains ou les pieds mouillés.

El generador es una fuente de descarga eléctrica.

No lo exponga a humedad, la lluvia, nin a la

nieve. No opere con manos o pies húmedos.

Exhaust contains poisonous carbon monoxide

gas that can cause unconsciousness or DEATH.

Operate in well ventilated, outdoor areas away

from open windows or doors.

L’échappement contient le gaz monoxyde de

carbone toxique qui peut causer l’inconscience

ou la MORT. Fonctionner dans les secteurs

bien ventilés et extérieurs loin d’ouvre des

fenêtres ou des portes.

El escape contiene gas venenoso de monóxido

de carbono que puede causar pérdida del

conocimiento o MUERTE. Opere en áreas exteriores

bien ventiladaslejos de puertas o ventanas abiertas.

Failure to properly ground generator can

result in electrocution, especially if the

generator is equipped with a wheel kit.

Une mauvaise mise à la terre du générateur

peut causer une électrocution, surtout si le

générateur est équipé d’un kit de roue.

La omisión de conectar a tierra

adecuadamente el generador puede resultar

en electrocución, especialmente si el

generador está equipado con un kit de ruedas.

Do not expose to rain or use in damp

locations.

Ne pas exposer à la pluie ou l’humidité.

No exponga a la lluvia ni use en lugares

húmedos.

DANGER PELIGRO

DANGER

940654199-01

 Une mauvaise mise à la terre du générateur peut causer

une électrocution, surtout si le générateur est équipé d’un

kit de roue.

 Ne pas exposer à la pluie ou l’humidité.

 L’utilisation d’une génératrice à l’intérieur PEUT VOUS

TUER EN QUELQUES MINUTES. Les génératrices

produisent du monoxyde de carbone, un gaz mortel

incolore et inodore.

 NE JAMAIS utiliser à l’intérieur d’une maison ou d’un

garage, MME SI les portes et les fenêtres sont ouvertes.

 Utiliser uniquement À L’EXTÉRIEUR et loin des fenêtres,

des portes et des évents.

Les informations ci-dessous se trouvent

sur le générateur. Pour des raisons de

sécurité, étudier et comprendre tous

les autocollants avant de mettre le

générateur en marche.

Si un autocollant se détache ou

devient illisible, contacter le centre

de réparations agréé pour obtenir un

autocollant de rechange.

Page 7 — Français

SYMBOLES

AVERTISSEMENT CONCERNANT LE CARBURANT

Ne pas fumer lors du plein. Ne pas trop remplir. Le plein est

obtenu à 25 mm (1 po) en dessous du haut du goulot de

remplissage. Arrêter le moteur pendant cinq minutes avant

de faire le plein pour éviter que la chaleur du silencieux

n’allume les vapeurs de carburant.