Kichler Lighting 44037NI Guía de instalación

Marca
Kichler Lighting
Modelo
44037NI
Tipo
Guía de instalación
IS-44037-CB
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
3) Connect mounng strap to outlet box using the strap
mounng screws[J].
4) Unscrew the threaded ring[F] from screw collar loop.
Take canopy[G] and pass over screw collar loop.
Approximately one half of the screw collar loop exterior
threads should be exposed. Adjust screw collar loop by
turning assembly up or down in mounng strap. Remove
canopy.
5) Aer desired posion is found, ghten both top and
boom hexnuts up against the boom and top of the
mounng strap.
6) Slip canopy over screw collar loop and thread on
threaded ring. Aach chain [H] (with xture connected)
to boom of screw collar loop. Unscrew threaded ring,
let canopy and threaded ring slip down. Aach chain to
xture if required.
7) Aach decorave loop[K] to top of main body[I]. Aach
chain to xture if required.
8) Weave electrical wire and ground wire through chain
links[H] no more than 3 inches apart. Pass wire through
threaded ring[F], canopy, screw collar loop, threaded
pipe and into outlet box.
9) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is provided,
aach ground wire from outlet box under cupped
washer and green ground screw, and thread into
mounng strap.
If xture is provided with ground wire, connect xture
ground wire to outlet box ground wire with wire
connector (Not provided) aer following the above steps.
Never connect ground wire to black or white power
supply wires.
10) Make wire connecon. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to: Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (See illus.) Neutral Wire
11) Lower the upper main body[I] down onto the upper light
er[P] and secure into place using the nial[Q].
12) Aach the support rod[L] to the upper main body[I] and
to the lower 6 light ring as shown.
13) Raise canopy to ceiling.
14) Secure canopy in place by ghtening threaded ring onto
screw collar loop.
15) Carefully lower glass[M] to the xture. Slip the smaller
opening over the socket and t the glass against the
socket.
16) Place glass spacer[N] into installed glass over socket.
17) Thread the socket ring[O] onto the socket. Tighten
socket ring to secure glass in place. (DO NOT over
ghten).
GREEN GROUND
SCREW CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
ab
Fixture Diagram
Parts List
[A] Threaded
Pipe
[B] Screw Collar
Loop
[C] Hexnut
[D] Mounting
Strap
[E] Outlet Box
[F] Threaded
Ring
[G] Canopy
[H] Chain (Links)
[I] Upper Main
Body
[J] Strap
Mounting
Screws
[K] Loop
[L] Support Rods
[M] Glass
[N] Glass Spacer
[O] Socket Ring
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
Installaon Instrucons
1) Take threaded pipe[A] from parts bag and screw in screw
collar loop[B] a minimum of 6 mm (1/4”). Lock into place
with hexnut[C].
2) Run another hexnut down threaded pipe almost touching
rst hexnut. Screw threaded pipe into mounng
strap[D]. Mounng strap must be posioned with
extruded thread faced into outlet box[E]. Threaded pipe
must protrude out the back of mounng strap. Screw
third hexnut onto end of threaded pipe protruding from
back of mounng strap.
Installaon Instrucons (connued)
E
O
N
M
D
CJ
AG
B
F
H
K
L
I
P
Q
IS-44037-CB
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
3) Connect mounng strap to outlet box using the strap
mounng screws[J].
4) Unscrew the threaded ring[F] from screw collar loop.
Take canopy[G] and pass over screw collar loop.
Approximately one half of the screw collar loop exterior
threads should be exposed. Adjust screw collar loop by
turning assembly up or down in mounng strap. Remove
canopy.
5) Aer desired posion is found, ghten both top and
boom hexnuts up against the boom and top of the
mounng strap.
6) Slip canopy over screw collar loop and thread on
threaded ring. Aach chain [H] (with xture connected)
to boom of screw collar loop. Unscrew threaded ring,
let canopy and threaded ring slip down. Aach chain to
xture if required.
7) Aach decorave loop[K] to top of main body[I]. Aach
chain to xture if required.
8) Weave electrical wire and ground wire through chain
links[H] no more than 3 inches apart. Pass wire through
threaded ring[F], canopy, screw collar loop, threaded
pipe and into outlet box.
9) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is provided,
aach ground wire from outlet box under cupped
washer and green ground screw, and thread into
mounng strap.
If xture is provided with ground wire, connect xture
ground wire to outlet box ground wire with wire
connector (Not provided) aer following the above steps.
Never connect ground wire to black or white power
supply wires.
10) Make wire connecon. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to: Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (See illus.) Neutral Wire
11) Lower the upper main body[I] down onto the upper light
er[P] and secure into place using the nial[Q].
12) Aach the support rod[L] to the upper main body[I] and
to the lower 6 light ring as shown.
13) Raise canopy to ceiling.
14) Secure canopy in place by ghtening threaded ring onto
screw collar loop.
15) Carefully lower glass[M] to the xture. Slip the smaller
opening over the socket and t the glass against the
socket.
16) Place glass spacer[N] into installed glass over socket.
17) Thread the socket ring[O] onto the socket. Tighten
socket ring to secure glass in place. (DO NOT over
ghten).
GREEN GROUND
SCREW CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
ab
Fixture Diagram
Parts List
[A] Threaded
Pipe
[B] Screw Collar
Loop
[C] Hexnut
[D] Mounting
Strap
[E] Outlet Box
[F] Threaded
Ring
[G] Canopy
[H] Chain (Links)
[I] Upper Main
Body
[J] Strap
Mounting
Screws
[K] Loop
[L] Support Rods
[M] Glass
[N] Glass Spacer
[O] Socket Ring
[P] Upper Light
Tier
[Q] Finial
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
Installaon Instrucons
1) Take threaded pipe[A] from parts bag and screw in screw
collar loop[B] a minimum of 6 mm (1/4”). Lock into place
with hexnut[C].
2) Run another hexnut down threaded pipe almost touching
rst hexnut. Screw threaded pipe into mounng
strap[D]. Mounng strap must be posioned with
extruded thread faced into outlet box[E]. Threaded pipe
must protrude out the back of mounng strap. Screw
third hexnut onto end of threaded pipe protruding from
back of mounng strap.
Installaon Instrucons (connued)
E
O
N
M
D
CJ
AG
B
F
H
K
L
I
P
Q
IS-44037-US
Estamos aquí para ayudarle 866-558-5706
Horario: Lunes-Viernes 9am a 5pm EST (hora ocial del este)
parte inferior y superior de la abrazadera de montaje.
6) Deslice el escudete sobre el ojal de collar roscado
y enrosque en el anillo roscado. Fije la eslabón de
cadena[H] (con el artefacto conectado) a la parte inferior
del ojal de collar roscado. Desenrosque el anillo roscado,
deje que el escudete y el anillo roscado se deslicen hacia
abajo. Aachez la chaîne au montage si nécessaire.
7) Una el lazo decoravo [K] a la parte superior del
cuerpo principal [I]. Adjunte la cadena al accesorio si es
necesario.
8) Entrelace el alambre eléctrico y el alambre de erra a
través de los acoplamientos de la cadena no más de 3
pulgadas aparte. Enhebre el cable a través del anillo
roscado, el refuerzo, el ojal roscado del collar, el tubo
roscado y en la caja de salida.
9) Instrucciones de conexión a erra solamente para los
Estados Unidos. (Vea la ilustracion a o b).
a) En las lámparas que enen el eje, de montaje con un
agujero y dos hoyuelos realzados, enrollar el alambre
a erra de la caja tomacorriente alrededor del tornillo
verde y pasarlo por el aquiero.
b) En las lámparas con una arandela acopada, jar el
alambre a erra de la caja tomacorriente del ajo de la
arandela acoada y tornillo verde, y paser por el eje
de montaje.
Si la lámpara viene con alambre a erra, conecter el
alambre a erra de la lámpara al alambre a erra de la
caja tomacorriente con un conector de alambres (No
incluido) espués de seguir los pasos anteriores. Nunca
conectar el alambra a erra a los alambres eléctros negro
o blanco.
10) Haga les conexiones de los alambres. La tabla de
referencia de abajo indica las conexiones correctas y los
alambres correspondientes.
Conectar el alambre de
suministro negro o rojo al Conectar el alambre de
suministro blanco al
Negro Blanco
*Cordon paralelo (redondo
y liso)
*Cordon paralelo (cuadrado
y estriado)
Claro, marrón, amarillio
o negro sin hebra
idencadora
Claro, marrón, amarillio
o negro con hebra
idencadora
Alambre aislado (diferente
del verde) con conductor
de cobre
Alambre aislado (diferente
del verde) con conductor
de plata
*Nota: Cuando se uliza alambre
paralelo (SPT 1 y SPT 2). El alambre
neutro es de forma cuadrada o
estriada y el otro alambre será
de forma redonda o lisa. (Vea la
ilustracíón). Hilo Neutral
11) Baje el cuerpo principal superior [I] hacia abajo sobre el
nivel de luz superior [P] y asegúrelo en su lugar ulizando
el remate [Q].
12) Fije la varilla de apoyo [L] al cuerpo principal superior [I]
y al anillo de 6 luces inferior como se indica.
13) Suba el escudete al techo.
14) Asegure el escudete en su lugar apretando el anillo
roscado sobre el ojal de collar roscado.
15) Baje cuidadosamente el vidrio [M] al artefacto. Pase la
abertura más pequeña sobre el portalámparas y ajuste
el vidrio contra el portalámparas.
16) Coloque el separador de vidrio [N] en el vidrio instalado
sobre el portalámparas.
17) Enrosque el anillo del portalámparas [O] en el
portalámparas. Apriete el anillo del portalámparas para
asegurar el vidrio en su lugar. (NO apriete demasiado).
18) Inserte las bombillas recomendadas. (No se proveen).
ARANDELA
CONCAVA
TIERRA DE LA
CAJA DE SALIDA
TORNILLO DE TIERRA,
VERDE
DEPRESIONES
TIERRA
ARTEFACTO
CONECTOR DE ALAMBRE
TIERRA DE LA
CAJA DE SALIDA
TORNILLO DE TIERRA,
VERDE
TIERRA
ARTEFACTO
ab
Diagrama de Accesorios
Lista de Partes
[A] Tubo Roscado
[B] Ojal del Collar
Roscado
[C] Tuerca
Hexagonal
[D] Abrazadera de
Montaje
[E] Caja de Salida
[F] Anillo Roscado
[G] Escudete
[H] Eslabón de
Cadena
[I] Cuerpo
Principal
Superior
[J] Tornillo De
Montaje
De La
Abrazadera
[K] El lazo
decoravo
[L] La varilla de
apoyo
[M] Vidrio
[N] Separador de
Vidrio
[O] Anillo del
Portalámparas
[P] De luz superior
[Q] Ulizando el
remate
Precauciones
PRECAUCIÓN – RIESGO DE DESCARGA ELÉCTRICA –
Desconecte la electricidad en el panel principal del
interruptor automáco o caja principal de fusibles antes de
comenzar y durante la instalación.
ADVERTENCIA:
Este accesorio está desnado a la instalación de
acuerdo con el Naonal Electrical Code (NEC) y todas las
especicaciones del código local. Si no está familiarizado
con los requisitos del código, la instalación se recomienda
un electricista cercado.
Instrucciones de Instalación
1) Tome el tubo roscado[A] de la bolsa de partes y
enrosque en el ojal del collar roscado[B] un mínimo
de 6 mm (1/4”). Asegúrelo en su lugar con una tuerca
hexagonal[C].
2) Coloque otra tuerca hexagonal en el tubo roscado casi
tocando la primera. Ahora enrosque el tubo roscado en
la abrazadera de montaje[D]. La abrazadera de montaje
debe estar colocada con la rosca extruida mirando a la
caja de salida[E]. El tubo roscado debe sobresalir de
atrás de la abrazadera de montaje. Enrosque la tercera
tuerca hexagonal en el extremo del tubo roscado que
sobresale de atrás de la abrazadera de montaje.
3) Conecte la abrazadera de montaje a la caja de salida con
los tornillos de montaje de la correa[X].
4) Desenrosque el anillo roscado[F] del ojal de collar
roscado. Tome el escudete[G] y páselo sobre el ojal de
collar roscado. Aproximadamente la mitad de las roscas
externas del ojal de collar roscado deben ser expuestas.
Ajuste el ojal de collar roscado girando el ensamblaje
hacia arriba o hacia abajo en la abrazadera de montaje.
Remueva el escudete.
5) Después de haber encontrado la posición deseada,
apriete la tuerca hexagonal de arriba y de abajo contra la
Instrucciones de instalación (connuación)
E
O
N
M
D
CJ
AG
B
F
H
K
L
I
P
Q
  • Page 1 1
  • Page 2 2
  • Page 3 3

Kichler Lighting 44037NI Guía de instalación

Marca
Kichler Lighting
Modelo
44037NI
Tipo
Guía de instalación
Descargar PDF
informe

En otros idiomas

Documentos relacionados