Titan GPX80 El manual del propietario
- Categoría
- Rociador de pintura
- Tipo
- El manual del propietario
0306 © 2006 SprayTECH. All rights reserved. Form No. 0555883A
Printed in the U. S. A.
GPX 80
Gas Piston Pump
Do not use this equipment before reading this manual!
SprayTECH
1770 Fernbrook Lane
Minneapolis, MN 55447
Technical Assistance: 1-800-292-4637
Order Entry: 1-800-443-4500
Fax: 1-800-525-9501
www.spraytechinc.com
Owner’s Manual
NOTE: This manual contains important warnings and
instructions. Please read and retain for reference.
Model Numbers:
Bare 0509007
Complete 0509037
Bare w/5 Gal. Siphon 0509053
Complete w/5 Gal. SIphon 0509057
Table of Contents
Safety Precautions.................................................................2
Français ..............................................................................18
Español...............................................................................20
Specifications .........................................................................3
General Description ...............................................................4
Operation ................................................................................4
Setup ....................................................................................4
Preparing to Paint.................................................................4
Painting.................................................................................5
Pressure Relief Procedure ...................................................6
Spraying ..................................................................................6
Spraying Technique ..............................................................6
Practice.................................................................................6
Cleanup ...................................................................................7
Maintenance............................................................................7
General Repair and Service Notes.......................................7
Maintaining the Engine .........................................................8
Replacing the Filter...............................................................8
Replacing the PRIME/SPRAY Valve.....................................8
Replacing the Potentiometer ................................................9
Replacing the Sprayer ON/OFF Switch................................9
Replacing the Gears and/or Slider Assembly.....................10
Replacing the Electronic Pressure Control (EPC) Board ...11
Replacing the Transducer...................................................11
Servicing the Clutch Assembly ...........................................12
Servicing the Fluid Section.................................................14
Troubleshooting ...................................................................16
Parts Listings........................................................................22
Main Assembly....................................................................22
Drive Assembly ...................................................................23
Fluid Section Assembly ......................................................24
Cart Assembly.....................................................................25
Filter Assembly ...................................................................25
PRIME/SPRAY Assembly ...................................................26
5 Gallon Siphon Set (optional) ...........................................26
Electrical Schematic ...........................................................27
Labels .................................................................................27
Accessories ........................................................................27
Limited Warranty ..................................................................28
Safety Precautions
This manual contains information that must be read and
understood before using the equipment. When you come to
an area that has one of the following symbols, pay particular
attention and make certain to heed the safeguard.
This symbol indicates a potential hazard that may cause
serious injury or loss of life. Important safety information
will follow
.
This symbol indicates a potential hazard to you or to the
equipment. Important information that tells how to
prevent damage to the equipment or how to avoid causes
of minor injuries will follow.
IMPORTANT SAFETY INSTRUCTIONS
A. SAVE THESE INSTRUCTIONS – To reduce the risks of
fire or explosion, electrical shock, and the injury to
persons, read and understand all instructions
included in this manual. Be familiar with the controls
and the proper usage of the equipment.
WARNING
NOTE: Notes give important information that should
be given special attention.
CAUTION
WARNING
2 © SprayTECH. All rights reserved.
B. WARNING – To reduce the risk of fire or explosion:
1. Do not spray flammable or combustible materials near
an open flame, pilot lights or sources of ignition such as
hot objects, cigarettes, motors, electrical equipment and
electrical appliances. Avoid creating sparks from
connecting and disconnecting power cords.
2. For units intended for use with only water-based
materials — Do not spray or clean with flammable
liquids. For use with water-based liquids only.
3. For units intended for use with only water-based or
mineral spirit-type materials with a minimum flash point
of 21ºC (69.8ºF) — Do not spray or clean with liquids
having a flash point of less than 21ºC (69.8ºF). Flash
point is the temperature at which a fluid can produce
enough vapor to ignite.
4. Paint or solvent flowing through the equipment is able
to result in static electricity. Static electricity creates a
risk of fire or explosion in the presence of paint or
solvent fumes. All parts of the spray system, including
the pump, hose assembly, spray gun and objects in and
around the spray area shall be properly grounded to
protect against static discharge and sparks. Use only
conductive or grounded high-pressure airless paint
sprayer hoses specified by the manufacturer.
5. Verify that all containers and collection systems are
grounded to prevent static discharge.
6. For electric units — connect to a grounded outlet and
use grounded extension cords. Do not use a 3 to 2
adapter.
7. Do not use a paint or solvent containing halogenated
hydrocarbons. Such as chlorine, bleach mildewcide,
methylene chloride and trichloroethane. They are not
compatible with aluminum. Contact the coating
supplier about compatibility of material with aluminum.
8. Keep spray area well ventilated. Keep a good supply of
fresh air moving through the area to keep the air within
the spray area free from accumulation of flammable
vapors. Keep pump assembly in well ventilated area.
Do not spray pump assembly.
9. Do not smoke in the spray area.
10. Do not operate light switches, engines, or similar spark
producing products in the spray area.
11. Keep area clean and free of paint or solvent
containers, rags, and other flammable materials.
12. Know the contents of the paint and solvents being
sprayed. Read all Material Safety Data Sheets (MSDS)
and container labels provided with the paints and
solvents. Follow the paint and solvent manufacture’s
safety instructions.
13. Place pump at least 25 feet (7.62 meters) from the
spray object in a well ventilated area (add more hose if
necessary). Flammable vapors are often heavier than
air. Floor area must be extremely well ventilated. The
pump contains arcing parts that emit sparks and can
ignite vapors.
14. Plastic can cause static sparks. Never hang plastic to
enclose spray area. Do not use plastic drop cloths
when spraying flammable material.
15. Fire extinguisher equipment shall be present and working.
C. W
ARNING – To reduce the risk of skin injection:
1. Do not aim the gun at, or spray any person or animal.
2. Keep hands and other body parts away from the
discharge. For example, do not try to stop leaks with
any part of the body.
HAZARD:
Injection injury – A high pressure fluid stream produced
by this equipment can pierce the skin and underlying
tissues, leading to a serious injury and possible
amputation. See a physician immediately. DO NOT
TREAT AN INJECTION AS A SIMPLE CUT.
WARNING
3. Always use the nozzle tip guard. Do not spray without
the nozzle tip guard in place.
4. Only use a nozzle tip specified by the manufacturer.
5. Use caution when cleaning and changing nozzle tips.
In the case where the nozzle tip clogs while spraying,
ALWAYS lock gun trigger, shut pump off, and release
all pressure before servicing, cleaning tip or guard, or
changing tip. Pressure will not be released by turning
off the motor. The PRIME/SPRAY valve handle must
be turned to PRIME to relieve the pressure. Refer to
PRESSURE RELIEF PROCEDURE described in the
pump manual.
6. Do not leave the unit energized or under pressure while
unattended. When the unit is not in use, turn off the unit
and relieve the pressure in accordance with the
manufacturer’s instructions.
7. High-pressure spray is able to inject toxins into the
body and cause serious bodily injury. In the event that
injection occurs, seek medical attention immediately.
8. Check hoses and parts for signs of damage, a leak can
inject material into the skin. Inspect hose before each
use. Replace any damaged hoses or parts.
9. This system is capable of producing 3300 PSI / 22.8
MPa. Only use replacement parts or accessories that
are specified by the manufacturer and that are rated a
minimum of 3300 PSI. This includes spray tips, nozzle
guards, guns, extensions, fittings, and hose.
10. Always engage the trigger lock when not spraying.
Verify the trigger lock is functioning properly.
11. Verify that all connections are secure before operating
the unit.
12. Know how to stop the unit and bleed pressure quickly.
Be thoroughly familiar with the controls. Pressure will
not be released by turning off the motor. The
PRIME/SPRAY valve handle must be turned to PRIME
to relieve the pressure. Refer to PRESSURE RELIEF
PROCEDURE described in the pump manual.
13. Always remove the spray tip before flushing or cleaning
the system.
D. WARNING – To reduce the risk of injury:
1. Always wear appropriate gloves, eye protection,
clothing and a respirator or mask when painting.
Hazardous vapors – Paints, solvents, insecticides, and
other materials can be harmful if inhaled or come in
contact with body. Vapors can cause severe nausea,
fainting or poisoning.
2.
Do not operate or spray near children. Keep children
away from equipment at all times.
3. Do not overreach or stand on an unstable support.
Keep effective footing and balance at all times.
4. Stay alert and watch what you are doing.
5. Do not operate the unit when fatigued or under the
influence of drugs or alcohol.
6. Do not kink or over-bend the hose. Airless hose can
develop leaks from wear, kinking and abuse. A leak
can inject material into the skin.
7. Do not expose the hose to temperatures or pressures in
excess of those specified by manufacturer.
8. Do not use the hose as a strength member to pull or lift
the equipment.
9. Use lowest possible pressure to flush equipment.
10. Follow all appropriate local, state and national codes
governing ventilation, fire prevention and operation.
11. The United States Government Safety Standards have
been adopted under the Occupational Safety and
Health Act (OSHA). These standards, particularly part
1910 of the General Standards and part 1926 of the
Construction Standards should be consulted.
WARNING
12. Before each use, check all hoses for cuts, leaks,
abrasion or bulging of cover. Check for damage or
movement of couplings. Immediately replace hose if
any of those conditions exist. Never repair a paint hose.
Replace with a conductive high-pressure hose.
13. Do not spray outdoors on windy days.
14. Always unplug cord from outlet before working on
equipment.
Do not lift by cart handle when loading or unloading.
Gasoline Engine Safety
The engine exhaust from this unit contains chemicals
known to the State of California to cause cancer, birth
defects, or other reproductive harm.
1. Gas engines are designed to give safe and dependable
service if operated according to instructions. Read and
understand the engine Owner's Manual before operating
the engine. Failure to do so could result in personal injury
or equipment damage.
2.
To prevent fire hazards and to provide adequate
ventilation, keep the engine at least 1 meter (3 feet) away
from buildings and other equipment during operation. Do
not place flammable objects close to the engine.
3. Children and pets must be kept away from the area of
operation due to a possibility of burns from hot engine
components or injury from any equipment the engine may
be used to operate.
4. Know how to stop the engine quickly, and understand the
operation of all controls. Never permit anyone to operate
the engine without proper instructions.
5. Gasoline is extremely flammable and is explosive under
certain conditions.
6. Refuel in a well-ventilated area with the engine stopped.
Do not smoke or allow flames or sparks in the refueling
area or where gasoline is stored.
7. Do not overfill the fuel tank. After refueling, make sure the
tank cap is closed properly and securely.
8. Be careful not to spill fuel when refueling. Fuel vapor or
spilled fuel may ignite. If any fuel is spilled, make sure the
area is dry before starting the engine.
9. Never run the engine in an enclosed or confined area.
Exhaust contains poisonous carbon monoxide gas;
exposure may cause loss of consciousness and may lead
to death.
10. The muffler becomes very hot during operation and
remains hot for a while after stopping the engine. Be
careful not to touch the muffler while it is hot. To avoid
severe burns or fire hazards, let the engine cool before
transporting it or storing it indoors.
11. Never ship/transport unit with gasoline in the tank.
Specifications
Gallons per minute (GPM)...............0.80 (3.0 LPM)
Maximum tip size .............................one gun = 0.026”
two guns = 0.019”
Maximum pressure ..........................3300 PSI (22.8 MPa)
Power...............................................4.5 HP gas engine
Weight..............................................128 lbs. (58.1 kg)
Maximum hose length......................300’ (91.4 m)
WARNING
CAUTION
© SprayTECH. All rights reserved. 3
General Description
This airless sprayer is a precision power tool used for spraying
many types of materials. Read and follow this instruction
manual carefully for proper operating instructions,
maintenance, and safety information.
Operation
This equipment produces a fluid stream at extremely high
pressure. Read and understand the warnings in the
Safety Precautions section at the front of this manual
before operating this equipment.
Setup
Perform the following procedure before starting the engine of a
gas-powered sprayer.
1. Ensure that the siphon tube and the return hose are
attached and secure.
2. Attach the supplied grounding cable to a grounded object.
3. Using a wrench, attach a minimum of 50’ of 1/4” nylon
airless spray hose to the outlet fitting on the sprayer.
Tighten securely.
4. Attach an airless spray gun to the spray hose. Using two
wrenches (one on the gun and one on the hose), tighten
securely.
Make sure all airless hoses and spray guns are electrically
grounded and rated at or above the maximum operating
pressure range of the airless sprayer
.
5. Turn the pressure control knob fully counterclockwise to
its lowest pressure setting.
6. Make sure the sprayer ON/OFF switch is in the OFF position.
7. Fill the fluid section oil cup with approximately one
tablespoon of separating oil (P/N 0279920).
Never operate unit for more than ten seconds without
fluid. Operating this unit without fluid will cause
unnecessary wear to the packings.
8. Check the engine oil level. The gasoline engine oil level
is determined by the manufacturer. Refer to the engine
manufacturer's service manual (supplied).
9. Close the fuel shut-off lever and fill the gas tank with
gasoline. Use only high quality, unleaded gasoline.
CAUTION
WARNING
NOTE: Do not attach the tip to the spray gun yet.
Remove the tip if it is already attached.
WARNING
Engine
Pressure Control
Knob
Pail Hook
Fluid Section
Siphon Tube
Cart
Filter
Assembly
PRIME/SPRAY
Valve
Outlet Fitting
4 © SprayTECH. All rights reserved.
Preparing a New Sprayer
If this unit is new, it is shipped with test fluid in the fluid section
to prevent corrosion during shipment and storage. This fluid
must be thoroughly cleaned out of the system with mineral
spirits before you begin spraying.
Always keep the trigger lock on the spray gun in the
locked position while preparing the system.
1. Place the siphon tube into a container of mineral spirits
that has a flash point of 60ºC (140ºF) or above.
2.
Place the return hose into a metal waste container.
3. Turn the pressure control knob fully counterclockwise to
its lowest pressure setting.
4. Move the PRIME/SPRAY valve to the PRIME position.
5. Move the engine ON/OFF switch to the ON position.
6. Start the engine:
a. Open the fuel valve
lever.
b. Move the throttle
lever away from the
gas tank.
c. Close the engine
choke lever.
d. Holding the frame
with one hand, pull
the starter rope
rapidly and firmly. Continue to hold the rope as you let it
return. Pull and return the rope until the engine starts.
7. Turn on the sprayer by moving
the sprayer ON/OFF switch to
the ON position.
8. Slowly turn the pressure control
knob clockwise to increase the
pressure until fluid starts to
come out of the return hose.
Use only enough pressure to
keep the fluid coming out.
9. Allow the sprayer to run for
15–30 seconds to flush the test fluid out through the
return hose and into the waste container.
10. Turn the pressure control knob fully counterclockwise to
its lowest setting.
11. Turn off the sprayer by moving the sprayer ON/OFF
switch to the OFF position.
Preparing to Paint
Before painting, it is important to make sure that the fluid in the
system is compatible with the paint that is going to be used.
Always keep the trigger lock on the spray gun in the
locked position while preparing the system.
1. Place the siphon tube into a container of the appropriate
solvent for the material being sprayed (refer to
recommendations of the material manufacturer). An
example of the appropriate solvent is water for latex paint.
2.
Place the return hose into a metal waste container.
3. Turn the pressure control knob fully counterclockwise to
its lowest pressure setting.
4. Move the PRIME/SPRAY valve to the PRIME position.
NOTE: Hold the return hose in the waste container
when moving the PRIME/SPRAY valve to
PRIME in case the sprayer is pressurized.
CAUTION
NOTE: Incompatible fluids and paint may cause the
valves to become stuck closed, which would
require disassembly and cleaning of the
sprayer’s fluid section.
Pressure
Control
Knob
Sprayer
ON/OFF
Switch
Fuel Valve
Lever
Choke Lever
Engine
ON/OFF
Switch
Throttle
Lever
Starter Rope
CAUTION
5. Move the engine ON/OFF switch to the ON position.
6. Start the engine:
a. Open the fuel valve lever.
b. Move the throttle lever away from the gas tank.
c. Close the engine choke lever.
d. Holding the frame with one hand, pull the starter rope
rapidly and firmly. Continue to hold the rope as you let
it return. Pull and return the rope until the engine
starts.
7. Turn on the sprayer by moving the sprayer ON/OFF
switch to the ON position.
8. Slowly turn the pressure control knob clockwise to
increase the pressure until fluid starts to come out of the
return hose. Use only enough pressure to keep the fluid
coming out.
9. Allow the sprayer to run for 15–30 seconds to flush the old
solvent out through the return hose and into the metal
waste container.
10. Turn the pressure control knob fully counterclockwise to
its lowest setting.
11. Turn off the sprayer by moving the sprayer ON/OFF
switch to the OFF position.
12. Move the PRIME/SPRAY valve to the SPRAY position.
13. Turn on the sprayer.
14. Turn the pressure control knob slowly clockwise to
increase pressure.
15. Unlock the gun by turning the gun trigger lock to the
unlocked position.
Ground the gun by holding it against the
edge of the metal container while
flushing. Failure to do so may lead to a
static electric discharge, which may
cause a fire.
16. Trigger the gun into the metal waste
container until the old solvent is gone
and fresh solvent is coming out of the gun.
17. Lock the gun by turning the gun trigger lock to the locked
position.
18.
Set down the gun and increase the pressure by turning
the pressure control knob slowly clockwise to its highest
setting.
19. Check the entire system for leaks. If leaks occur, turn the
sprayer off and follow the “Pressure Relief Procedure” in
this manual before tightening any fittings or hoses.
20. Follow the “Pressure Relief Procedure” in this manual
before changing from solvent to paint.
Be sure to follow the pressure relief procedure when
shutting the unit down for any purpose, including
servicing or adjusting any part of the spray system,
changing or cleaning spray tips, or preparing for cleanup.
Painting
1. Place the siphon tube into a container of paint.
2. Place the return hose into a metal waste container.
3. Turn the pressure control knob fully counterclockwise to
its lowest pressure setting.
4. Move the PRIME/SPRAY valve to the PRIME position.
5. Move the engine ON/OFF switch to the ON position.
6. Start the engine:
a. Open the fuel valve lever.
b. Move the throttle lever away from the gas tank.
WARNING
WARNING
NOTE: Make sure that the spray gun does not have a
tip or tip guard installed.
c. Close the engine
choke lever
.
d. Holding the frame
with one hand, pull
the starter rope
rapidly and firmly.
Continue to hold
the rope as you let
it return. Pull and
return the rope until
the engine starts.
7. Turn on the sprayer
by moving the sprayer ON/OFF switch to the ON position.
8. Slowly turn the pressure control
knob clockwise to increase the
pressure until fluid starts to
come out of the return hose.
Use only enough pressure to
keep the fluid coming out.
9. Allow the sprayer to run until
paint is coming through the
return hose into the metal
waste container.
10. Turn the pressure control knob fully counterclockwise to
its lowest setting.
11. Turn off the sprayer by moving the sprayer ON/OFF
switch to the OFF position.
12. Remove the return hose from the waste container and place
it in its operating position above the container of paint.
13. Move the PRIME/SPRAY valve to the SPRAY position.
14. Turn on the sprayer.
15. Turn the pressure control knob slowly clockwise to
increase pressure.
16. Unlock the gun by turning the gun trigger lock to the
unlocked position.
Ground the gun by holding it against the
edge of the metal container while
flushing. Failure to do so may lead to a
static electric discharge, which may
cause a fire.
17. Trigger the gun into the metal waste
container until all air and solvent is flushed from the spray
hose and paint is flowing freely from the gun.
18.
Lock the gun by turning the gun trigger lock to the locked
position.
19. Turn the pressure control knob fully counterclockwise to
its lowest setting.
20. Turn off the sprayer.
21. Attach tip guard and tip to the gun as instructed by the tip
guard or tip manuals.
POSSIBLE INJECTION HAZARD. Do not spray without the
tip guard in place. Never trigger the gun unless the tip is in
either the spray or the unclog position.
Always engage the
gun trigger lock before removing, replacing or cleaning tip.
22. Turn on the sprayer.
23.
Increase the pressure by turning the pressure control
knob slowly clockwise and test the spray pattern on a
piece of cardboard. Adjust the pressure control knob until
the spray from the gun is completely atomized. Try to
keep the pressure control knob at the lowest setting that
maintains good atomization.
NOTE: Turning the pressure up higher than needed to
atomize the paint will cause premature tip wear
and additional overspray.
WARNING
WARNING
Pressure
Control
Knob
Sprayer
ON/OFF
Switch
Fuel Valve
Lever
Choke Lever
Engine
ON/OFF
Switch
Throttle
Lever
Starter Rope
© SprayTECH. All rights reserved. 5
Pressure Relief Procedure
Be sure to follow the pressure relief procedure when
shutting the unit down for any purpose, including
servicing or adjusting any part of the spray system,
changing or cleaning spray tips, or preparing for cleanup.
1. Lock the gun by turning the gun trigger lock to the locked
position.
2. Turn off the sprayer by moving the sprayer ON/OFF
switch to the OFF position.
3. Turn off the engine by moving the engine ON/OFF switch
to the OFF position.
4. Turn the pressure control knob counterclockwise to its
lowest setting.
5. Unlock the gun by turning the gun trigger lock to the
unlocked position.
4. Hold the metal part of the gun firmly to
the side of a metal container to ground
the gun and avoid a build up of static
electricity.
5. Trigger the gun to remove any pressure
that may still be in the hose.
6. Lock the gun by turning the gun trigger lock to the locked
position.
7. Move the PRIME/SPRAY valve to the PRIME position.
Spraying
Spraying Technique
The key to a good paint job is an even coating over the entire
surface. This is done by using even strokes. Keep your arm
moving at a constant speed and keep the spray gun at a
constant distance from the surface. The best spraying distance
is 10 to 12 inches between the spray tip and the surface.
Keep the spray gun at right angles to the surface. This means
moving your entire arm back and forth rather than just flexing
your wrist.
Heavy Coat
Do not flex wrist while spraying.
Light Coat Light Coat
K k h d d
Even coat throughout
Approximately
10 to 12 inches
NOTE: When spraying block filler, mastics or high
solid coating, remove the gun filter and high
pressure filter screens.
WARNING
6 © SprayTECH. All rights reserved.
Keep the spray gun perpendicular to the surface, otherwise
one end of the pattern will be thicker than the other.
The spray gun should be triggered by turning it on and off with
each stroke. This will save paint and avoid paint buildup at the
end of the stroke. Do not trigger the gun during the middle of
a stroke. This will result in an uneven spray and splotchy
coverage.
Overlap each stroke by about 30%. This will ensure an even
coating.
When you stop painting, lock the gun trigger lock, turn the
pressure control knob counterclockwise to its lowest setting
and set the PRIME/SPRAY valve to PRIME. Turn the motor
switch to OFF and unplug the sprayer.
Practice
1. Be sure that the paint hose is free of kinks and clear of
objects with sharp cutting edges.
2. Turn the pressure control knob counterclockwise to its to
its lowest setting.
3. Move the PRIME/SPRAY valve to the SPRAY position.
4. Turn the pressure control knob clockwise to its highest
setting. The paint hose should stiffen as paint begins to
flow through it.
5. Unlock the gun trigger lock.
6. Trigger the spray gun to bleed air out of the hose.
7. When paint reaches the spray tip, spray a test area to
check the spray pattern.
8. Use the lowest pressure
setting necessary to get a
good spray pattern. If the
pressure is set too high, the
spray pattern will be too light.
If the pressure is set too low,
tailing will appear or the paint
will spatter out in gobs rather
than in a fine spray.
Good spray pattern
Paint tailing pattern
Proper way to trigger the spray gun
Approximately
10 to 12 inches
Keep stroke
even
Start stroke End strokePull trigger Release triggerKeep steady
Approximately
10 to 12 inches
Right way
Wrong way
Cleanup
Special cleanup instructions for use with flammable
solvents:
• Always flush spray gun preferably outside and at least one
hose length from spray pump.
• If collecting flushed solvents in a one gallon metal
container
, place it into an empty five gallon container, then
flush solvents.
• Area must be free of flammable vapors.
• Follow all cleanup instructions.
The sprayer
, hose, and gun should be cleaned thoroughly
after daily use. Failure to do so permits material to build
up, seriously affecting the performance of the unit.
Always spray at minimum pressure with the gun nozzle tip
removed when using mineral spirits or any other solvent
to clean the sprayer, hose, or gun. Static electricity
buildup may result in a fire or explosion in the presence of
flammable vapors.
1. Follow the “Pressure Relief Procedure” found in the
Operation section of this manual.
2.
Remove the gun tip and tip guard and clean with a brush
using the appropriate solvent.
3. Place the siphon tube into a container of the appropriate
solvent (refer to recommendations of the material
manufacturer). An example of the appropriate solvent is
water for latex paint.
4. Place the return hose into a metal waste container.
5. Move the PRIME/SPRAY valve to its PRIME position.
6. Move the engine ON/OFF switch to the ON position and
start the engine.
7. Turn on the sprayer by moving
the sprayer ON/OFF switch to
the ON position.
8. Slowly turn the pressure control
knob clockwise to increase the
pressure until fluid starts to
come out of the return hose.
9. Allow the solvent to circulate
through the sprayer and flush
the paint out of the return hose
into the metal waste container.
10. Turn the pressure control knob fully counterclockwise to
its lowest setting.
11. Turn off the sprayer by moving the ON/OFF switch to the
OFF position.
12. Move the PRIME/SPRAY valve to its SPRAY position.
13. Turn on the sprayer.
14. Turn the pressure control knob slowly clockwise to
increase pressure.
Ground the gun by holding it against the
edge of the metal container while
flushing. Failure to do so may lead to a
static electric discharge, which may cause a fire.
WARNING
Pressure
Control
Knob
Sprayer
ON/OFF
Switch
NOTE: Hold the return hose in the waste container
when moving the PRIME/SPRAY valve to
PRIME in case the sprayer is pressurized.
WARNING
CAUTION
WARNING
© SprayTECH. All rights reserved. 7
15. Trigger the gun into the metal waste container until the
paint is flushed out of the hose and solvent is coming out
of the gun.
16. Continue to trigger the spray gun into the waste container
until the solvent coming out of the gun is clean.
17. Follow the “Pressure Relief Procedure” found in the
Operation section of this manual.
18. Store the sprayer in a clean, dry area.
Do not store the sprayer under pressure.
Cleaning the Spray Tip
1. Flush the gun with solvent immediately after the work is
completed.
2. Oil the sliding pins to prevent them from seizing up.
Should the spray tip become clogged, reverse
the spray tip with the lever and pull the trigger.
Once the obstruction comes out of the spray tip,
release the trigger, reverse the spray tip back to
the spray pattern setting, and resume spraying.
Do not attempt to clean the tip with your finger.
Do not use a needle or other sharp pointed instrument to
clean the tip. The hard tungsten carbide is brittle and can
be chipped.
Maintenance
Before proceeding, follow the Pressure Relief Procedure
outlined previously in this manual. Additionally, follow all
other warnings to reduce the risk of an injection injury,
injury from moving parts, or electric shock.
General Repair and Service Notes
The following tools are needed when repairing this sprayer:
Phillips screwdriver 3/8" hex wrench
needle-nose pliers 5/16" hex wrench
adjustable wrench 1/4" hex wrench
rubber mallet 3/16" hex wrench
flat-blade screwdriver 1/8” hex wrench
1/2” open-end wrench 7/8” open-end wrench
1. Before repairing any part of the sprayer, read the
instructions carefully, including all warnings.
Never pull on a wire to disconnect it. Pulling on a wire
could loosen the connector from the wire.
2. Test your repair before regular operation of the sprayer to
be sure that the problem is corrected. If the sprayer does
not operate properly
, review the repair procedure to
determine if everything was done correctly. Refer to the
Troubleshooting section to help identify other possible
problems.
CAUTION
NOTE: All Honda engine work should be performed by
a Honda authorized service center.
WARNING
WARNING
CAUTION
NOTE: For long-term or cold weather storage, pump
mineral sprits through the entire system.
3. Make certain that the service area is well ventilated in
case solvents are used during cleaning. Always wear
protective eyewear while servicing. Additional protective
equipment may be required depending on the type of
cleaning solvent. Always contact the supplier of solvents
for recommendations.
4. If you have any further questions concerning your
SprayTECH airless sprayer, call SprayTECH:
Technical Service...................................1-800-292-4637
Fax ................................................1-800-525-9501
Maintaining the Engine
When transporting a sprayer with a gas engine, make sure
the fuel is shut off.
Important Facts Concerning this Sprayer
This gas-powered sprayer contains a clutch that engages
when the sprayer is pumping. The sprayer’s pressure control
system engages and disengages the clutch to control
pressure. To prevent unnecessary wear to the clutch, it is
advisable to adjust the engine speed and pressure setting to
limit the amount of times the clutch engages and disengages.
To reduce clutch wear, refer to the following examples.
Example:
Operating one gun with a .019 tip — reduce the engine speed
by adjusting the throttle to a low or medium setting and
increase pressure only until the heavy ends of the spray
pattern have been eliminated.
Example:
Operating one gun with .023 tip — increase engine speed to a
higher setting and increase pressure until the heavy ends of
the spray pattern have been eliminated.
Example:
Spraying light-bodied materials at low pressure — to reduce
surging at the gun and to decrease clutch wear, reduce the
engine speed to idle and reduce pressure until the desired
spray pattern is achieved.
Routine Engine Maintenance
Daily
• Check and fill the gas tank.
• After the first 20 hours of operation, drain the oil and refill
with clean oil. Check the engine oil level and fill as
necessary.
Weekly
• Remove the cover of the air filter and clean the element.
Replace the element if necessary
. If operating in an
unusually dusty environment, check the filter daily and
replace if necessary. (Replacement elements can be
purchased from your local SprayTECH dealer.)
• After each 50 hours of operation: Change the engine oil.
Spark Plug
• Use only a (NKG) BP6ES plug.
•
Gap the plug 0.025” – 0.030” (0.7 – 0.8 mm).
• Make sure to use a spark plug wrench when installing and
removing the plug.
NOTE: For detailed engine specifications and
maintenance, refer to the separate engine
manual supplied with this sprayer.
WARNING
8 © SprayTECH. All rights reserved.
Replacing the Filter
1. Loosen and remove the filter
body by hand.
2. Remove the filter and core
spring from the filter housing.
3. Remove the core spring from
inside the filter.
4. Inspect the filter. Based on
inspection, clean or replace the
filter.
5. Inspect the filter housing o-ring.
Based on inspection, clean or
replace the o-ring.
6. Slide the new or cleaned filter
over the core spring. Place the
filter and core spring into the
center of the filter housing.
7. Clean the inside of the filter
body.
8. Slide the filter body over the
filter and thread it into the filter
housing until secure.
Replacing the PRIME/SPRAY Valve
Perform the following procedure using PRIME/SPRAY valve
replacement kit P/N 0507690.
1. Drive the groove pin out of the valve handle.
2. Remove the valve handle and the cam base.
3. Using a wrench, loosen and remove the valve housing
assembly.
4. Make sure the gasket is in place and thread the new valve
housing assembly into the filter housing. Tighten securely
with a wrench.
5. Place the cam base over the valve housing assembly.
Lubricate the cam base with grease and line up the cam
with the filter block using the dowel pin.
6. Line up the hole on the valve stem with the hole in the
valve handle.
7. Insert the groove pin into the valve handle and through
the valve stem to secure the valve handle in position.
Dowel Pin
Cam Base
Valve Stem
Filter
Housing
Valve Housing
Assembly
Gasket
Valve Handle
Groove Pin
NOTE: The filter body should
be hand-tightened,
but make sure it is
seated fully into the
filter housing.
Filter
Body
Core
Spring
Filter
Filter
Housing
O-ring
Filter
Housing
Replacing the Potentiometer
Electrostatic discharge (ESD) potential could cause
damage to electronic pressure control. Use SprayTECH
ESD wrist strap P/N 0507958 or equivalent when working
on electronic pressure control.
1. Perform the Pressure Relief Procedure.
2.
Pry off the pressure control knob cap to expose the knob
tension nut.
3. Turn the pressure control knob fully counterclockwise to
the minimum pressure setting.
4. Using a 5/16” socket, loosen the tension nut in the center
of the knob. Remove the knob.
5. Using a Phillips screwdriver, remove the four screws that
secure the electronic pressure control (EPC) assembly to
the EPC housing. Carefully remove the EPC assembly
from the housing. Gently move the assembly away from
the sprayer and allow the assembly to hang from the
housing.
6. Hold the potentiometer inside the EPC housing while
using a 1/2” thin wall socket to remove the seal nut that
secures the potentiometer to the mounting plate. Remove
the potentiometer from the EPC housing.
7. Carefully remove the potentiometer wires from their
connection point on the EPC board.
8. Insert the stem of the new potentiometer through the hole
in the mounting plate from inside the EPC housing.
Position the protruding tab on the potentiometer face into
the hole on the underside of the mounting plate (the wires
will face the open side of the EPC housing).
9. Thread the seal nut onto the threaded portion of the stem
and tighten using a 1/2” thin wall socket.
Do not over-tighten the seal nut.
10. Turn the potentiometer stem fully counterclockwise.
11. Place the pressure control knob on the potentiometer
stem with the indicator tab resting at the “minimum
pressure” tab on the mounting plate.
12.
Tighten the knob tension nut using a 5/16” socket.
Do not over-tighten the knob tension nut. Over-tightening
will damage the potentiometer
.
13. Connect the potentiometer wires to the EPC board. The
protruding tab on the EPC board connector will mate with
the slot on the potentiometer wires connector. The
connector on the end of the potentiometer wires and the
connector on the EPC board will mate only one way. Do
not force the connectors together.
14. Carefully place the EPC assembly over the EPC housing
taking care not to pinch any wires.
15. Install the four screws that secure the EPC assembly to
the EPC housing. Tighten securely.
CAUTION
CAUTION
EPC
Housing
Pressure Control Knob
Seal Nut
Cap
EPC
Board
EPC
Assembly
EPC
Assembly
Screw
Potentiometer
WARNING
Replacing the Sprayer ON/OFF Switch
Electrostatic discharge (ESD) potential could cause
damage to electronic pressure control. Use SprayTECH
ESD wrist strap P/N 0507958 or equivalent when working
on electronic pressure control.
1. Perform the Pressure Relief Procedure.
2.
Using a Phillips screwdriver, remove the four screws that
secure the electronic pressure control (EPC) assembly to
the EPC housing. Carefully remove the EPC assembly
from the housing. Gently move the assembly away from
the sprayer and allow the assembly to hang from the
housing.
3. Locate the bottom of the sprayer ON/OFF switch inside
the EPC housing.
4. Disconnect the switch wires from the sprayer ON/OFF
switch. Remember the locations of each of the two wires
(label the wires, if necessary).
5. Depress the mounting tabs on each corner of the sprayer
ON/OFF switch inside the EPC housing and remove the
switch through the top of the housing.
6. Snap the new sprayer ON/OFF switch into the switch hole
in the EPC housing.
7. Connect the two switch wires to the new sprayer ON/OFF
switch. Make sure the wires are connected to the
corresponding terminals from which they were removed
(refer to the labels created earlier in this procedure or the
electrical schematic in the Parts List section of this
manual).
8. Carefully place the EPC assembly over the EPC housing
taking care not to pinch any wires.
9. Install the four screws that secure the EPC assembly to
the EPC housing. Tighten securely.
Sprayer ON/OFF
Switch
EPC
Board
EPC
Assembly
EPC
Assembly
Screw
WARNING
© SprayTECH. All rights reserved. 9
Replacing the Gears and/or
Slider Assembly
1. Using a Phillips screwdriver, remove the four front cover
screws. Remove the front cover.
2. Start the engine (refer to the procedures in the Operation
section of this manual). Turn the pressure control knob
clockwise to its maximum pressure setting.
3. Toggle the sprayer ON/OFF switch between the ON and
OFF positions in short bursts until the slider assembly and
piston stop at the bottom of their stroke (in their lowest
position).
4. Turn off the engine and perform the Pressure Relief
Procedure.
5. Using a 11/16” open-
end wrench, loosen
and remove the fluid
hose from the fitting
on the back of the
fluid section.
6. Using a 3/8” hex
wrench, remove the
two socket screws
that secure the fluid
section to the pump
housing.
7. Slide the retaining
ring up on the slider
assembly to expose
the connecting pin.
8. Push the connecting
pin through the slider assembly and piston toward the
back of the pump housing. The connecting pin will fall into
a recessed area of the pump housing where it can be
retrieved.
9. Remove the fluid section by pulling it straight down from the
pump housing until the dowel pins on the pump housing
disengage from the fluid section housing.
10. Using a 1/4” hex wrench,.remove the four socket screws
that secure the pump housing to the gear housing.
11. Slide the pump housing away from the gear housing.
12. Remove and clean the housing gasket. Replace if damaged.
13. Slide the crankshaft assembly, with the two thrust washers
out from the gear housing side of the pump housing.
14. Remove the output gear assembly with the two thrust
washers.
15. Thoroughly clean the crankshaft assembly, the output gear
assembly, and all the thrust washers.
Connecting
Rod
Slider Bushing
Slider Assembly
Gear Housing
Pump Housing
Output Gear
Assembly
Thrust
Washer
Thrust Washer
Housing Gasket
Large Thrust Washer
Crankshaft Assembly
Cylindrical Thrust Washer
Pump Housing
Socket Screw
Fitting
Piston
Retaining
Ring
Pump
Housing
Slider
Assembly
Front
Cover
Screw
Fluid
Section
Housing
Socket
Screw
Front
Cover
Connecting
Pin
NOTE: If replacing the slider assembly, the fluid section
must be removed from the pump housing.
10 © SprayTECH. All rights reserved.
15. Inspect all parts for excessive wear and replace if
damaged or worn. If the crankshaft or output gear
assembly are replaced, replace the corresponding thrust
washers as well.
16. Inspect the pinion gear on the end of the drive shaft for
wear. Replace if damaged or worn (refer to the “Servicing
the Clutch Assembly” procedure in this section).
17. Slide the slider assembly up and out of the slider bushing
in the front of the pump housing.
18. Check the parts for wear.
a. If the slider bushing is scored or out of round it should
be replaced.
b. If the slider assembly is scored or the connection
between the connecting rod and slider assembly
exhibits movement other than pivoting movement, the
slider assembly should be replaced. The slider
assembly also should be replaced if the connecting rod
bearing shows signs of wear.
c. Any parts that will be reused should be cleaned
thoroughly, including the connecting rod. Also, clean the
crankshaft pin that the connecting rod bearing rides on.
d. If the slider bushing requires replacement, a press must
be used. Position the pump housing so that the
bushing is facing the arbor on the press. Position the
new bushing on top of the old bushing. Lower the
arbor on the press to contact the new bushing and
press the new bushing into the bore. As the new
bushing is pressed into the bore, the old bushing is
pressed out of the bore. The new bushing is in place
when it is flush with the bore wall on the pump housing.
19. Coat the output gear assembly and each side of its thrust
washers with fresh Lubriplate GR-132 grease. Place the
thrust washers on their proper shaft of the output gear
assembly.
20. Lubricate the output gear assembly with fresh Lubriplate
GR-132 grease. Insert the gear assembly into its bore in
the gear housing, gear end first. The teeth on the gear
will mate with the teeth on the drive shaft pinion.
21. Generously coat all surfaces of the cylindrical crankshaft
assembly thrust washer with fresh Lubriplate GR-132
grease.
22. Slip the flat end of the cylindrical thrust washer behind the
gear on the output gear assembly, lining its bore up with the
gear housing bearing bore for the crankshaft assembly.
23. Lubricate the crankshaft assembly gear with fresh
Lubriplate GR-132 grease. Slide the gear side shaft of
the crankshaft through the cylindrical thrust washer and
into its bore within the gear housing.
24. Position the pin on the end of the crankshaft towards the
bottom of the gear housing (the bottom dead center
position).
25. Lubricate both faces of the large crankshaft assembly
thrust washer with fresh Lubriplate GR-132 grease. Place
the thrust washer onto the crankshaft against the gear.
26. Place the housing gasket over the gear housing dowel pins.
27. Lubricate the outside of the slider assembly and the inside of
the slider bushing with oil. Fill the slider cup with Lubriplate
1242 grease (the slider cup is the area on the slider
assembly where the connecting rod and slider join and pivot).
28. Insert the slider assembly into the slider bushing so that
the small dimple on the face of the connecting rod faces
the open side of the pump housing.
29. Carefully place the pump housing assembly in front of the
gear housing assembly, lining up the gear housing dowel
pins with their corresponding holes in the pump housing.
Slide the pump housing onto the gear housing until there
is no gap between the housings and gasket.
NOTE: If any of the gears are worn and require
replacement, check the grease in the gear
housing for metal particles or shavings.
Remove the contaminated grease. Replace the
grease that has been removed with fresh
Lubriplate GR-132 grease.
Do not force the pump housing and gear housing together.
30. Locate the four socket screws and lock washers that secure
t
he pump housing to the gear housing. The longer screws
(2.25”) are fastened into the top internal holes. The shorter
screws (2”) are fastened into the bottom external bosses.
31. Using a 1/4” hex wrench, snug and tighten the socket
screws in a crossing pattern. Torque to 200–230 in./lbs.
32. If the fluid section was removed, reinstall by pushing the
fluid section up toward the pump housing until the dowel
pins in the pump housing engage the holes in the fluid
section housing. When the connecting pin hole on the
piston rod lines up with the hole in the slider assembly,
insert the connecting pin.
33. Slide the retaining ring down over the connecting pin.
34. Insert the two socket screws that secure the fluid section
to the pump housing and alternately snug, tighten, and
torque the screws to 400-440 in./lbs.
35. Position the front cover over the pump housing. Secure
the front cover using the four front cover screws.
36. Using a 11/16” open-end wrench, attach the fluid hose to
the fitting on the back of the fluid section. Tighten securely.
Replacing the Electronic Pressure
Control (EPC) Assembly
Electrostatic discharge (ESD) potential could cause
damage to electronic pressure control. Use SprayTECH
ESD wrist strap P/N 0507958 or equivalent when working
on electronic pressure control.
1. Perform the Pressure Relief Procedure.
2. Using a Phillips
screwdriver, remove
the four screws that
secure the electronic
pressure control
(EPC) assembly to the
EPC housing.
Carefully remove the
EPC assembly from
the housing. Gently
move the assembly
away from the sprayer
and allow the assembly to hang from the housing.
3. Remember the locations of all the wire connections on the
EPC board (refer the electrical schematic located in the
Parts List section of this manual). If necessary, label all
the connections so that they can be replaced in their exact
location when the assembly is replaced.
4. Disconnect all the wires from the EPC board.
5. Connect all the wires to the new EPC assembly board (refer
to the labels created earlier in this procedure or the
electrical schematic in the Parts List section of this manual).
6. Carefully place the EPC assembly over the EPC housing
taking care not to pinch any wires.
7. Install the four screws that secure the EPC assembly to
the EPC housing. Tighten securely.
8. Take the sprayer to a SprayTECH Authorized Service
Center for re-calibration.
EPC
Housing
EPC Assembly Screw
EPC Assembly
EPC
Board
WARNING
CAUTION
NOTE: While sliding the pump housing into place, the
crankshaft pin will begin to protrude from the
bearing in the center of the pump housing.
Position the slider assembly so that as the
crankshaft pin protrudes from the main bearing,
it engages the connecting rod bearing.
Replacing the Transducer
Electrostatic discharge (ESD) potential could cause
damage to electronic pressure control. Use SprayTECH
ESD wrist strap P/N 0507958 or equivalent when working
on electronic pressure control.
1. Perform the Pressure Relief Procedure.
2. Using a Phillips
screwdriver
, remove
the four screws that
secure the electronic
pressure control
(EPC) assembly to
the EPC housing.
Carefully remove the
EPC assembly from
the housing. Gently
move the assembly
away from the sprayer
and allow the assembly to hang from the housing.
3. Locate the transducer wire in the EPC housing. This wire
will be protruding from a hole in the lower left hand corner
of the EPC housing. Disconnect this wire from the EPC
board (it has a phone jack-style connector).
4. Break off the locking tab from the phone jack-style
connector at the end of the transducer wire.
5. Using a 7/8” open-end wrench, loosen and remove the fluid
hose from the fitting on the bottom of the filter assembly.
6. Remove the return hose from the fitting on the bottom of
the filter assembly.
7. Using a 1/2” socket, remove the two hex screws that
secure the filter assembly to the cart.
8. Lift the filter assembly off the cart so that the transducer
tube moves out of the hole in the gear housing. Gently
pull the transducer wire through the housing until it is fully
disengaged from the hole.
9. Mount the filter assembly in a vise for easy access to the
transducer.
Do not over-tighten the vise.
10. Using a 3/4” open-end wrench, turn the transducer nut
counterclockwise to remove the transducer from the filter
housing.
11.
Locate the new transducer. Make sure that there is a
white, PTFE o-ring on the end of the transducer that gets
inserted into the filter housing.
12. Insert the transducer into the filter housing port. Rotate
the transducer nut clockwise to tighten it into the filter
housing. Torque the nut to 360–400 in./lbs.
13. Remove the filter assembly from the vise.
Transducer
Filter Assembly
Hex Screw
Gear Housing
Return
Hose
Fitting
Filter
Assembly
Fluid
Hose
Fitting
Cart
CAUTION
EPC
Housing
EPC Assembly Screw
EPC Assembly
EPC
Board
WARNING
© SprayTECH. All rights reserved. 11
14. Insert the phone jack-style connector on the new
transducer wire into the hole in the gear housing from
which the old transducer wire was removed. Push the
wire and connector until the connector is visible in the
EPC housing.
15. Gently pull the wire into the EPC housing while moving
the filter assembly to its mounting point on the cart. Guide
the end of the transducer tube into the hole in the gear
housing.
16. Mount the filter assembly to the cart using the two hex
screws and lock washers. Torque the screws to 100–130
in./lbs.
17. Using a 7/8” open-end wrench, attach the fluid hose to the
fitting on the bottom of the filter assembly. Tighten securely.
18. Push the return hose firmly into the fitting on the bottom of
the filter assembly. Pull on the hose to make sure it has
engaged within the fitting.
19. Plug the phone jack-style connector on the transducer
wire into the socket on the EPC board from which the old
connector was removed.
20. Carefully place the EPC assembly over the EPC housing
taking care not to pinch any wires.
21. Install the four screws that secure the EPC assembly to
the EPC housing. Tighten securely.
22. Take the sprayer to a SprayTECH Authorized Service
Center for re-calibration.
23. After re-calibration, pressurize the system and check for
leaks.
Servicing the Clutch Assembly
Removing/Replacing the Clutch Armature
Assembly
1. Perform the Pressure Relief Procedure.
2. Using a 11/16” open-end wrench, loosen and remove the
fluid hose from the fitting on the back of the fluid section.
3. Hold the transducer tube with a pliers to prevent it from
rotating and turn the transducer nut counterclockwise
using a 3/4” open-end wrench. When the nut disengages
the filter housing, carefully remove the transducer from the
filter housing.
4. Locate the wire that exits the rear of the electronic
pressure control (EPC) housing and connects to the wire
harness on the engine. Disconnect this wire from its
connector at the engine wire harness.
5. Using a 1/2” wrench, remove the four hex screws and lock
washers that secure the clutch housing to the gear housing.
6. Using a 9/16” socket, remove the two hex screws that
secure the gear housing to the cart.
NOTE: When replacing the clutch armature, the clutch
rotor must be replaced also. This will allow for
even wear and maximum life on clutch parts.
Transducer
Filter Assembly
Hex Screw
Gear Housing
Return
Hose
Fitting
Filter
Assembly
Fluid
Hose
Fitting
Cart
12 © SprayTECH. All rights reserved.
7. Slide the pump and gear housings away from the engine
to disengage them from the clutch housing.
8. Locate the clutch armature assembly on the end of the
engine shaft. Note the two set screws as well as the
unused, threaded hole in the taper lock bushing at the
center of the clutch hub.
9. Using an 1/8” hex wrench, remove the two set screws
from the taper lock bushing
10. Thread one of the set screws into the unused, threaded hole
on the taper lock bushing. As the screw tightens, the bushing
will loosen. Once the bushing has loosened enough, slide the
clutch armature assembly off the engine shaft.
11. To replace the clutch armature assembly , line up the
three holes in the taper lock bushing with the three holes
in the clutch armature and insert the bushing into the
center of the clutch armature.
12. Line up the key on the taper lock bushing with the keyway
on the engine shaft and slide the assembly onto the shaft
with the holes facing out.
13. Apply blue Loctite to the two set screws and insert the
screws into the taper lock bushing. Tighten the set screws
only two turns at this time.
15. Using the clutch set-up
tool (P/N 0509926),
position the clutch
armature on the engine
shaft. Hold the tool
across the face of the
clutch housing so that
the center, recessed
portion of the tool
straddles the clutch
armature assembly. Pull
the clutch armature
assembly towards the
tool until the face of the armature is against the tool.
15. While holding the clutch armature assembly against the
tool, use an 1/8” hex wrench and alternately tighten the
set screws into the taper lock bushing. Torque to 65–75
in/lbs.
16. Make sure the friction surface of the clutch armature is
clean and free from oil or grease.
Removing the Clutch Rotor, Clutch Field, and
Drive Shaft Assembly
1. Follow steps 1–7 in “Removing/Replacing the Clutch
Armature Assembly.”
2. Locate the clutch rotor assembly, which will be protruding out
from the gear housing. Note the locations of the three socket
screws and the two empty, threaded holes on the clutch rotor.
3. Using a 3/16” hex wrench, remove the three socket
screws and lock washers that secure the clutch rotor to
the drive shaft assembly.
4. Thread two of the socket screws into the empty, threaded
holes and tighten alternately. This will push the clutch
rotor away from the drive shaft assembly and pinion.
Clutch
Housing
Engine
Set
Screw
Set-Up
Tool
Taper
Lock
Bushing
Taper Lock Bushing
Gear
Housing
Clutch Armature
Pump
Housing
Lock Washer
Clutch
Housing
Clutch Housing
Hex Screw
Set Screw
Engine Shaft
Gear Housing
Hex Screw
Electrostatic discharge (ESD) potential could cause
damage to electronic pressure control. Use SprayTECH
ESD wrist strap P/N 0507958 or equivalent when working
on electronic pressure control.
5. Using a Phillips screwdriver, remove the four screws that
secure the EPC assembly to the EPC housing. Carefully
remove the EPC assembly from the housing.
6. Locate the two clutch field wires that pass from the gear
housing into the EPC housing through a grommet in the
back of the EPC housing. Remember the wire connection
terminals on the EPC assembly (label if necessary) and
disconnect the wires. Gently move the EPC assembly
away from the housing and rest it on the work surface by
the control housing.
7. Locate the four pairs of set screws that secure the clutch
field to the gear housing. They are located on the exterior
of the gear housing at the 12, 3, 6, and 9 o’clock positions
while facing the clutch field end of the gear housing.
Using an 1/8” hex wrench, remove the setscrews.
Remember the location of the two clutch field wires with
respect to the grommet and EPC housing.
8. Carefully slide the clutch field out of the gear housing,
keeping the field square to the gear housing so it does not
bind.
9. Using a Phillips screwdriver, remove the four front cover
screws. Remove the front cover.
10. Using a 11/16” open-end wrench, loosen and remove the
fluid hose from the fitting on the back of the fluid section.
11. Using a 1/4” hex wrench, remove the four socket screws
that secure the pump housing to the gear housing.
12. Slide the pump housing away from the gear housing.
13. Remove and clean the housing gasket. Replace if
damaged.
14. Locate the drive shaft pinion that is protruding from the
front side of the gear housing. Remove the small snap
ring that is located on the drive shaft hub in front of the
ball bearing that is supporting the drive shaft.
15. From the opposite side of the gear housing (clutch side)
slide the drive shaft assembly out of the gear housing.
16. Inspect the grease seal located inside the bore from which
the drive shaft was removed. Replace if worn or
damaged. To remove the grease seal, use a flat blade
screwdriver to carefully pry the seal from the bore.
17. Clean the inside of the gear housing.
NOTE: To remove the drive shaft assembly, the pump
housing first must be removed from the gear
housing.
Clutch Rotor Socket Screw
Drive Shaft Assembly
Pointed Set
Screw
Set Screw
Clutch Field
Assembly
Lock
Washer
Clutch
Rotor
Clutch Field
Wires
EPC Assembly
EPC Assembly Screw
WARNING
Installing the Clutch Rotor Assembly, Clutch
Field and Drive Shaft Assembly
1. If the drive shaft grease seal was removed, press a new
seal into the bore from which the old seal was removed.
2. From the clutch side of the gear housing, insert the drive
shaft assembly into the bore, through the grease seal, and
through the ball bearing on the gear side of the gear
housing.
3. From the gear side of the gear housing, insert the snap
ring into the groove on the drive shaft hub in front of the
ball bearing.
4. Place the housing gasket over the gear housing dowel pins.
5. Carefully place the pump housing assembly in front of the
gear housing assembly, lining up the gear housing dowel
pins with their corresponding holes in the pump housing.
Slide the pump housing onto the gear housing until there
is no gap between the housings and gasket.
Do not force the pump housing and gear housing together.
6. Locate the four socket screws and lock washers that secure
the pump housing to the gear housing. The longer screws
(2.25”) are fastened into the top internal holes. The shorter
screws (2”) are fastened into the bottom external bosses.
7. Using a 1/4” hex wrench, snug and tighten the socket
screws in a crossing pattern. Torque to 200–230 in./lbs.
8.
Line up the four holes around the outside of the clutch
field with the four set screw holes in the gear housing.
The clutch field wires should be at approximately the 1 or
2 o’clock position.
9. Route the two clutch field wires through the grommet and
into the EPC housing.
10. Carefully slide the clutch field into its bore in the gear
housing until it “bottoms out” within the housing. Do not
pinch the clutch field wires during installation.
11. Thread one of the pointed set screws into its hole. Using
an 1/8” hex wrench, rotate the screw slowly until it
contacts the clutch field. Do not tighten the set screw.
The tip of the set screw should mate with the drill point
hole in the field. Check the clutch field for rotation. If it
rotates within its bore, the set screw is not seated within
the drill point.
12. When the set screw is properly seated, install the remaining
three pointed set screws. Do not tighten the set screws.
13. Using a crossing pattern, tighten each of the pointed
setscrews until they are snug. Once all four pointed set
screws are snug, use a crossing pattern to tighten and
torque the set screws to 30–40 in./lbs.
It is very important to evenly snug, tighten, and torque the
clutch field pointed set screws in a crossing pattern. This
ensures the clutch field will stay centered in the gear
housing.
CAUTION
CAUTION
Grease Seal
Bearing
Snap Ring
Small Snap Ring
Front Cover
Pump Housing Socket Screw
Front Cover Screw
Plug
Housing Gasket
© SprayTECH. All rights reserved. 13
14. Install the remaining four set screws over the four pointed
set screws. Using an 1/8” hex wrench, tighten each of the
set screws in a crossing pattern until they are snug. Once
all four set screws are snug, use a crossing pattern to
tighten and torque the set screws to 60–70 in./lbs.
15. Line up the three screw holes and dowel pin hole on the
clutch rotor with the screw holes and dowel pin on the drive
shaft assembly hub. Place the clutch rotor onto the hub.
16. Using a 3/16” hex wrench, thread the three socket screws
and lock washers through the clutch rotor and into the
drive shaft assembly hub. Evenly snug, tighten, and
torque the socket screws to 75–85 in/lbs.
17. Make sure the friction surface of the clutch rotor is clean
and free from oil or grease.
Electrostatic discharge (ESD) potential could cause
damage to electronic pressure control. Use SprayTECH
ESD wrist strap P/N 0507958 or equivalent when working
on electronic pressure control.
18. Locate the two clutch field wires in the EPC housing.
Gently pull the wires fully into the EPC housing so that
there is no slack in the gear housing. Connect the wires
to their proper terminals on the EPC board (refer to the
labels created earlier in this procedure or the electrical
schematic in the Parts List section of this manual).
19. Carefully place the EPC assembly over the EPC housing
taking care not to pinch any wires.
20. Install the four screws that secure the EPC assembly to
the EPC housing. Tighten securely.
Mating the Gear Housing and the Clutch
Housing
1. Place the gear housing assembly onto the cart in front of
the clutch housing. Line up the dowel pins in the gear
housing with their corresponding holes in the clutch
housing. Slide the gear housing assembly onto the clutch
housing until there is no gap between the housings.
2. Thread the four hex screws and lock washers through the
clutch housing and into the gear housing.
3. Using a 1/2” wrench, snug and tighten the hex screws in a
crossing pattern. Torque to 140–155 in./lbs.
4. Using a 9/16” socket, thread the two hex screws that secure
the gear housing to the cart through the underside of the
cart and into the gear housing. Torque to 100–120 in./lbs.
5. Connect the wire from the EPC housing to its mating
connector on the engine wire harness.
6. Make sure that there is a white PTFE o-ring on the end of
the transducer that gets inserted into the filter housing.
Insert the transducer into the filter housing port.
7. Hold the transducer tube with a pliers to prevent it from
rotating, and turn the transducer nut clockwise with a 3/4”
open-end wrench to tighten it into the filter housing.
Torque the nut to 360–400 in./lbs.
Checking the Clutch Gap
1. Remove the plastic plug from the top of the clutch
housing. Look through the port to locate the clutch
armature and the clutch rotor.
2. Check the gap between the clutch armature and the clutch
rotor using a .016” feeler gauge and a .035” feeler gauge.
a. Insert each feeler gauge through the port and into the
gap between the clutch armature and the clutch rotor.
The .016” feeler gauge should fit in the gap. The .035”
feeler gauge should not fit in the gap.
b. Pull the engine pull cord several times to rotate the
clutch armature, checking the gap with each feeler
gauge between each pull.
c. If the .016” gauge does not fit or the .035” gauge does fit
at any checkpoint, the gap must be readjusted. This is
done by relocating the clutch hub and armature assembly
on the engine shaft. Refer to the “Removing/Replacing
the Clutch Armature Assembly” procedure.
WARNING
14 © SprayTECH. All rights reserved.
Servicing the Fluid Section
Use the following procedures to service the valves and repack
the fluid section.
1. Using a Phillips screwdriver, remove the four front cover
screws. Remove the front cover.
2. Start the engine (refer to the procedures in the Operation
section of this manual). Turn the pressure control knob
clockwise to its maximum pressure setting.
3. Toggle the sprayer ON/OFF switch between the ON and
OFF positions in short bursts until the slider assembly and
piston rod stop at the bottom of their stroke (in their lowest
position).
4. Turn off the engine and perform the Pressure Relief
Procedure.
Before proceeding, follow the Pressure Relief Procedure
outlined previously in this manual. Additionally
, follow all
other warnings to reduce the risk of an injection injury,
injury from moving parts or electric shock.
Servicing the Valves
The design of the fluid section
allows access to the inlet valve
and seat as well as the outlet
valve and seat without
completely disassembling the
fluid section. It is possible that
the valves may not seat properly
because of debris stuck in the
inlet valve seat or outlet valve
seat. Use the following
instructions to clean the valves
and reverse or replace the seats.
1. Using a wrench, loosen and
remove the inlet valve
housing from the fluid
section housing.
2. Clean out any debris in the inlet valve housing and
examine the valve housing and seat. If the inlet valve
seat is damaged, reverse the seat to the unused side or
replace the seat.
3. Using a 3/8" hex wrench, loosen and remove the outlet
valve retainer from the piston rod.
4. Clean out any debris and
examine the outlet valve retainer
and seat. If the outlet valve seat
is damaged, reverse to the
unused side or replace the seat.
5. Remove, clean, and inspect the outlet cage, crush
washer, and outlet valve ball. Replace if they are worn or
damaged.
6. Reassemble the valves by reversing the steps above.
NOTE: If the outlet valve seat is reversed or replaced,
the outlet valve ball must be replaced.
NOTE: Always service the
outlet valve with the
piston rod attached to
the pump. This will
prevent the piston rod
from rotating during
disassembly of the
outlet valve.
Piston Rod
Outlet Cage
Crush Washer
Outlet Valve
Seat
Outlet Valve
Retainer
Outlet Valve
Ball
NOTE: If the inlet valve seat is reversed or replaced,
the inlet valve ball must be replaced.
NOTE: Keep the sprayer in
the upright position
for this procedure.
Fluid Section
Housing
Inlet Valve Seal
Inlet Valve Seat
PTFE O-Ring
Inlet Valve
Housing
Piston Bushing
Inlet Cage
Inlet Valve Ball
WARNING
Repacking the Fluid Section
1. Remove the inlet valve
and outlet valve
assemblies using the
steps in the “Servicing
the Valves” procedure
above.
2. Using a 11/16” open-end
wrench, loosen and
remove the fluid hose
from the fitting on the
back of the fluid section.
3. Using a 3/8” hex wrench,
remove the two socket
screws that secure the
fluid section to the pump
housing.
4. Slide the retaining ring
up on the slider
assembly to expose the
connecting pin.
5. Push the connecting pin
through the slider
assembly and piston
toward the back of the
pump housing. The
connecting pin will fall
into a recessed area of
the pump housing where
it can be retrieved.
6. Remove the fluid section
by pulling it straight down
from the pump housing
until the dowel pins on the
pump housing disengage
form the fluid section
housing.
7. Slide the piston rod out
through the bottom of the fluid section housing.
8. Using a wrench, loosen and remove the retainer nut and
piston guide from the fluid section housing.
9. Remove the upper and lower packings from the fluid
section housing.
10. Clean the fluid section housing thoroughly
11. Locate the new upper and lower packing assemblies. .
Remove the piston insertion tool from the upper packing
and the seal sizing tool from the lower packing.
12 Pack the areas between the
packing lips with grease
(included in repacking kit).
Lubricate the o-rings on the
exterior of the packings with
grease.
13. Insert the upper packing
assembly into the top of the
fluid section housing with the raised lip facing down into
the housing.
Install upper packing
with raised lip
facing down.
Raised Lip
NOTE: Be careful not to scratch, score, or otherwise
damage the inside of the fluid section housing
during removal of the packing assemblies.
Slider
Assembly
Retainer
Nut
Retaining
Ring
Connecting
Pin
Piston
Guide
Fluid
Section
Housing
Upper
Packing
Lower
Packing
Socket
Screw
Piston
Rod
Fitting
NOTE: The factory-installed packings are red in color.
The replacement packings in the packing
replacement kit are white.
14. Insert the lower packing
assembly into the bottom of the
fluid section housing with the
large beveled edge facing
toward the housing (beveled
edge will be facing up when
the housing is upright).
15
Inspect the piston rod for wear
and replace if necessary.
16 Reassemble the outlet valve assembly into the piston rod
using the new o-ring, outlet valve seal, and outlet valve ball
that came with the repacking kit. Apply blue Loctie to the
threads of the outlet valve retainer. Torque the outlet valve
retainer to 300–350 in./lbs.
Never use a wrench on the piston rod itself. This could
cause damage to the piston and cause leakage.
17. Insert the new piston guide into the retainer nut. Thread
the retainer nut into the fluid section housing until it is
hand tight.
18.
Slide the piston guide tool (included in the repacking kit)
over the top of the piston rod.
19. Insert the piston rod into the bottom of the fluid section
housing, through the lower packing, through the upper
packing, and out through the retainer nut. Using a rubber
mallet, tap the bottom of the piston rod lightly until the
piston rod is in position in the fluid section housing.
20. Using a wrench, tighten the retainer nut. Torque to 550-
600 in./lbs.
21. Position the fluid section underneath the pump housing by
lining up the pump housing dowel pins with their
respective holes in the top of the fluid section housing.
Push the fluid section up towards the pump housing,
engaging the dowel pins, until the fluid section housing
rests against the pump housing. When the connecting pin
hole on the piston rod lines up with the hole in the slider
assembly, insert the connecting pin.
22. Insert the two socket screws that secure the fluid section
to the pump housing and alternately snug, tighten, and
torque the screws to 400-440 in./lbs.
23. Reassemble the inlet valve using the new inlet valve seal,
o-ring, and inlet valve ball. Thread the inlet valve
assembly into the fluid section housing and torque to 350-
400 in./lbs.
24. Position the front cover over the pump housing. Secure
the front cover using the four front cover screws.
25. Using a 11/16” open-end wrench, attach the fluid hose to
the fitting on the back of the fluid section. Tighten
securely.
26. Turn on the sprayer by following the procedure in the
“Operation” section of this manual and check for leaks.
NOTE: Repacking kit P/N 0509909 is available. For
best results use all parts supplied in this kit.
NOTE: Make sure the raised lip on the bottom of the
lower packing assembly is fully outside the
packing around the piston rod after insertion
of the piston rod.
NOTE: Coat the piston guide tool and the piston rod
with grease before inserting them into the fluid
section housing.
CAUTION
Install lower packing so
large beveled edge will
be facing up when the fluid
section housing is upright.
Large Beveled Edge
© SprayTECH. All rights reserved. 15
Troubleshooting
16 © SprayTECH. All rights reserved.
Solution
1. Turn the pressure control knob clockwise to
supply power to the unit and increase the
pressure setting.
2. Inspect or take to a SprayTECH authorized
service center.
3. Fill the gas tank.
1. Rotate the PRIME/SPRAY valve clockwise
to the PRIME position.
2. Check the siphon tube/siphon set
connection and tighten or re-tape the
connection with PTFE tape.
3. Remove the pump filter element and clean.
Remove the inlet screen and clean.
4. Remove the siphon tube/siphon set and
clean.
1. Replace the spray tip following the
instructions that came with the spray gun.
2. Replace the spray tip with a tip that has a
smaller orifice following the instructions that
came with the spray gun.
3. Turn the pressure control knob clockwise to
increase the pressure setting.
4. Remove the pump filter element and clean.
Remove the gun filter and clean. Remove
the inlet screen and clean.
5. Clean or replace the PRIME/SPRAY valve.
6. Check the siphon tube/siphon set
connection and tighten or re-tape the
connection with PTFE tape.
7. Check for external leaks at all connections.
Tighten connections, if necessary.
8. Clean the valves and service the fluid
section following the “Servicing the Fluid
Section” procedure in the Maintenance
section of this manual.
9. Reverse or replace the valve seats
following the “Servicing the Fluid Section”
procedure in the Maintenance section of
this manual.
1. Repack the pump following the “Servicing
the Fluid Section” procedure in the
Maintenance section of this manual.
2. Replace the piston rod following the
“Servicing the Fluid Section” procedure in
the Maintenance section of this manual.
Cause
1. The pressure is set too low.
2. Faulty or loose wiring.
3. The gas tank is empty.
1. The PRIME/SPRAY valve is in the
SPRAY position.
2. Air leak in the siphon tube/siphon set.
3. The pump filter and/or inlet screen is
clogged.
4. The siphon tube/siphon set is clogged.
1. The spray tip is worn.
2. The spray tip is too large.
3. The pressure control knob is not set
properly.
4. The pump filter, gun filter, or inlet
screen is clogged.
5. Material flows from the return hose
when the PRIME/SPRAY valve is in the
SPRAY position.
6. Air leak in the siphon tube/siphon set.
7. There is external fluid leak.
8. There is an internal fluid section leak
(packings are worn and/or dirty, valve
balls are worn).
9. Worn valve seats
1. The upper packings are worn.
2. The piston rod is worn.
Troubleshooting
Problem
The unit will not run.
The unit will not prime.
The unit will not build or
maintain pressure.
Fluid leakage at the upper end
of the fluid section.
© SprayTECH. All rights reserved. 17
Troubleshooting
Problem
Excessive surge at the spray
gun.
Poor spray pattern.
The unit lacks power.
Cause
1. Wrong type of airless spray hose.
2. The spray tip worn or too large.
3. Excessive pressure.
1. The spray tip is too large for the
material being used.
2. Incorrect pressure setting.
3. Insufficient fluid delivery.
4. The material being sprayed is too
viscous.
1. The pressure adjustment is too low.
Solution
1. Replace hose with a minimum of 50’ of 1/4”
grounded textile braid airless paint spray
hose.
2. Replace the spray tip following the
instructions that came with the spray gun.
3. Rotate the pressure control knob
counterclockwise to decrease spray
pressure.
1. Replace the spray tip with a new or smaller
spray tip following the instructions that
came with the spray gun.
2. Rotate the pressure control knob to adjust
the pressure for a proper spray pattern.
3. Clean all screens and filters.
4. Add solvent to the material according to the
manufacturer's recommendations.
1. Rotate the pressure control knob clockwise
to increase the pressure setting.
18 © SprayTECH. Tous droits réservés.
Consignes de sécurité
Le présent manuel comprend des renseignements devant être
lus attentivement avant toute utilisation de l'appareil. Lorsque
l'un des symboles suivants apparaît, il est recommandé d'être
particulièrement attentif et de tenir compte des mesures de
sécurité indiquées.
Ce symbole indique un danger potentiel pouvant causer des
blessures graves ou même mortelles. Des renseignements
importants sur la sécurité sont également indiqués.
Ce symbole indique un danger potentiel pouvant causer des
blessures corporelles ou des dommages à l'équipement. Des
renseignements importants sur la façon de prévenir tout
dommage à l'équipement ou toute blessure corporelle mineure
sont également indiqués.
CONSIGNES DE SÉCURITÉ IMPORTANTES
A.
CONSERVEZ CES CONSIGNES – Pour réduire les
risques d’incendie ou d’explosion, d’électrocution et
de blessures, lisez et assurez-vous de bien
comprendre toutes les consignes contenues dans ce
manuel. Familiarisez-vous avec les commandes et
l’usage correct de l’équipement.
B. AVERTISSEMENT – Pour réduire le risque d’incendie
ou d’explosion :
1. Ne pulvérisez pas de matières inflammables ou
combustibles près d’une flamme nue, de voyants
lumineux ou de sources d’ignition telles que des objets
chauds, cigarettes, moteurs, matériel et appareils
électriques. Évitez de produire des étincelles en
connectant et en déconnectant les cordons électriques.
2. Pour les appareils destinés à n’utiliser que des produits
à l’eau – Ne pulvérisez pas et ne les nettoyez pas avec
des liquides inflammables. Exclusivement pour usage
avec liquides à base d’eau.
3. Pour les appareils destinés à un usage exclusif avec des
produits à l’eau ou des produits minéraux de type alcool
avec un point d’éclair minimum de 21 ºC (70 ºF) – Ne
pulvérisez pas et ne les nettoyez pas avec des liquides
ayant un point d’éclair inférieur à 21 ºC (70 ºF). Le point
d’éclair est la température à laquelle un fluide peut
produire suffisamment de vapeur pour s’enflammer.
4. L’écoulement de peinture ou de solvant dans
l’équipement peut produire de l’électricité statique.
L’électricité statique crée un risque d’incendie ou
d’explosion en présence de fumées de peinture ou de
solvant. Toutes les pièces du système du pulvérisateur,
y compris la pompe, l’ensemble du tuyau, le pistolet de
pulvérisation et les objets dans et autour de la zone de
pulvérisation doivent être correctement reliés à la terre
pour protéger contre les décharges d’électricité statique
et les étincelles. N’utilisez que des tuyaux conducteurs
ou reliés à la terre pour pulvérisateurs de peinture sous
vide à haute pression, spécifiés par le fabricant.
5. Vérifiez que tous les conteneurs ou systèmes de
stockage sont reliés à la terre pour éviter les décharges
d’électricité statique.
6. Connectez à une prise électrique avec prise de terre et
utilisez des rallonges électriques reliées à la terre.
N’utilisez pas d’adaptateur 3 à 2.
AVERTISSEMENT
NOTA : Les remarques donnent des renseignements
importants requérant une attention particulière.
ATTENTION
AVERTISSEMENT
7. N’utilisez pas de peinture ou de solvant contenant du
halon, par exemple, le chlore, les agents antimoisissure à
l’eau de Javel, le chlorure de méthylène et le
trichloroéthane. Ils ne sont pas compatibles avec
l’aluminium. Contactez le fournisseur de revêtements pour
connaître la compatibilité du matériau avec l’aluminium.
8. La zone de pulvérisation doit toujours être bien aérée.
Une bonne quantité d’air frais doit constamment
traverser la zone de pulvérisation pour éviter les
accumulations de vapeurs inflammables. Le système
de pompage doit être placé dans une zone bien aérée.
Ne pulvérisez pas le système de pompage.
9. Ne fumez pas dans la zone de pulvérisation.
10. N’actionnez pas d’interrupteurs électriques, de moteurs
ou autres dispositifs produisant des étincelles dans la
zone de pulvérisation.
11. Maintenez la propreté de la zone et veillez à ce qu’elle
ne contienne pas de conteneurs de peinture ou de
solvant, de chiffons et autres matières inflammables.
12. Sachez ce que contiennent la peinture et les solvants
pulvérisés. Lisez les fiches de sécurité du matériel
(MSDS) et les étiquettes apposées sur les conteneurs
de peintures et de solvants. Respectez les consignes
de sécurité du fabricant de peinture et de solvant.
13. Placez la pompe à une distance minimum de 7,62 mètres
(25 pieds) de l’objet à pulvériser, dans une zone bien
aérée (ajoutez de la longueur de tuyau si besoin est). Les
vapeurs inflammables sont souvent plus lourdes que l’air.
La zone près du sol doit être très bien aérée. La pompe
contient des pièces qui produisent des arcs et émettent
des étincelles pouvant enflammer les vapeurs.
14. Le plastique peut causer des étincelles d’électricité
statique. N’accrochez aucun plastique dans une zone
de pulvérisation fermée. N’utilisez pas de toiles de
protection en plastique quand vous pulvérisez une
matière inflammable.
15. Ayez un extincteur en bon état de fonctionnement à
portée de main.
C. AVERTISSEMENT – Pour réduire le risque de
pénétration dans la peau :
1. Ne dirigez pas le pistolet sur et ne pulvérisez pas les
personnes ou les animaux.
2.
N’approchez pas les mains ni d’autres parties du corps
de la sortie du produit. Par exemple, ne tentez pas
d’arrêter une fuite avec une partie du corps.
3. Utilisez toujours le protège-embout de la buse. Ne
pulvérisez pas sans que le protège-embout de la buse
ne soit installé.
4. Utilisez exclusivement un embout de buse spécifié par
le fabricant.
5. Prenez garde quand vous nettoyez ou que vous changez
les embouts de buse. Si l’embout se bouche pendant que
vous pulvérisez, verrouillez TOUJOURS la détente du
pistolet, arrêtez la pompe et libérez toute la pression
avant de réparer ou de nettoyer l’embout ou le protecteur
ou avant de changer d’embout. La pression n’est pas
libérée par l’arrêt du moteur. La poignée du robinet-valve
PRIME/SPRAY (AMORÇAGE/ PULVÉRISATION) doit
être placée sur PRIME pour libérer la pression. Consultez
la PROCÉDURE DE LIBÉRATION DE PRESSION
décrite dans le manuel de la pompe.
DANGER :
Blessure par injection – Le jet de fluide à haute pression
produit par cet équipement peut transpercer la peau et
les tissus sous-jacents, ce qui produit de graves
blessures et peut entraîner une amputation. Consultez
immédiatement un médecin. NE TRAITEZ PAS UNE
INJECTION COMME UNE SIMPLE COUPURE.
AVERTISSEMENT
Français
© SprayTECH. Tous droits réservés. 19
6. Ne laissez pas l’appareil sous tension ou sous pression
quand vous vous en éloignez. Quand vous n’utilisez
pas l’appareil, éteignez-le et libérez la pression
conformément aux instructions du fabricant.
7. La pulvérisation à haute pression peut injecter des
toxines dans le corps et causer de graves blessures
corporelles. Si une telle injection se produisait,
consultez immédiatement un médecin.
8. Vérifiez les tuyaux et les pièces pour détecter des signes
d’endommagement : une fuite peut injecter le produit
dans la peau. Inspectez le tuyau avant chaque emploi.
Changez tous les tuyaux ou pièces endommagés.
9. Ce système peut produire une pression de 3300 PSI /
22.8 MPa. N’utilisez que les pièces de rechange ou les
accessoires spécifiés par le fabricant et ayant une
pression nominale minimum de 3300 PSI. Ceci est
valable pour les embouts de pulvérisation, les
protecteurs de buse, les pistolets, les rallonges, les
raccords et le tuyau.
10. Verrouillez toujours la détente quand vous ne pulvérisez
pas. Vérifiez que le verrou de la détente fonctionne
correctement.
11. Vérifiez que toutes les connexions sont bien serrées
avant d’utiliser l’appareil.
12. Sachez comment arrêter l’appareil et le dépressuriser
rapidement. Soyez bien familiarisé avec les
commandes. La pression n’est pas libérée lorsque le
moteur est arrêté. La poignée du robinet-valve
PRIME/SPRAY (AMORÇAGE/PULVÉRISATION) doit
être placée sur PRIME pour libérer la pression.
Consultez la PROCÉDURE DE LIBÉRATION DE
PRESSION décrite dans le manuel de la pompe.
13. Retirez toujours l’embout de pulvérisation avant de
rincer ou de nettoyer le système.
D. AVERTISSEMENT – Pour réduire le risque de blessure :
1. Portez toujours les gants, la protection oculaire, les
vêtements et un respirateur ou masque appropriés
quand vous peignez. Vapeurs dangereuses – Les
peintures, solvants, insecticides et autres matières
peuvent être dangereux s’ils sont inhalés ou entrent en
contact avec le corps. Les vapeurs peuvent provoquer
d’importantes nausées, une perte de connaissance ou
un empoisonnement.
2.
Ne travaillez pas et ne pulvérisez pas près d’enfants.
Éloignez toujours les enfants de l’équipement.
3. Ne travaillez pas avec les bras au-dessus de la tête ni
sur un support instable. Appuyez-vous bien sur les
deux pieds pour toujours conserver l’équilibre.
4. Soyez attentif et regardez ce que vous faites.
5. N’utilisez pas l’appareil quand vous êtes fatigué ou
sous l’influence de drogues ou d’alcool.
6. Ne faites pas de n?uds avec le tuyau et ne le tordez
pas trop. Le tuyau à vide peut présenter des fuites suite
à l’usure, les n?uds ou les mauvais traitements. Une
fuite risque d’injecter du produit dans la peau.
7. N’exposez pas le tuyau à des températures ou des
pressions supérieures à celles spécifiées par le fabricant.
8. N’utilisez pas le tuyau pour tirer ou soulever l’équipement.
9. Utilisez la plus basse pression possible pour rincer
l’équipement.
10. Respectez tous les codes locaux, étatiques et
nationaux qui régulent la ventilation, la prévention
d’incendies et le fonctionnement.
11. Les normes de sécurité du gouvernement des États-
Unis ont été adoptées dans la loi Occupational safety
and Health Act (OSHA). Ces normes, en particulier la
partie 1910 des Normes générales et la partie 1926
des Normes de construction, doivent être consultées.
AVERTISSEMENT
12. Avant chaque emploi, vérifiez tous les tuyaux pour
détecter d’éventuelles coupures, fuites, abrasion ou
couvercle bombé. Vérifiez l’état ou le mouvement des
accouplements. Changez immédiatement le tuyau si
l’une de ces conditions est vérifiée. Ne réparez jamais
un tuyau de peinture. Remplacez-le par un tuyau
conducteur à haute pression.
13. Ne pulvérisez pas à l’extérieur par temps venteux.
14. Débranchez toujours le cordon électrique de la prise
avant de travailler sur l’équipement.
Sécurité des moteurs à essence
Les produits chimiques contenus dans les vapeurs
d'échappement de cet appareil sont reconnus par l'État de
la Californie (États-Unis) comme étant cancérigènes. Ils
peuvent également entraîner des anomalies congénitales
ou d’autres dangers pour la santé.
1. Les moteurs Honda sont conçus pour fonctionner en toute
sécurité et avec une fiabilité maximale s'ils sont utilisés
conformément aux instructions. V
euillez lire et
comprendre le manuel de l’utilisateur de Honda avant de
faire fonctionner le moteur. Le non-respect de ces
consignes peut entraîner des dommages matériels ou des
blessures physiques graves.
2. Pour éviter tout risque d'incendie et fournir une ventilation
adéquate, placez le moteur à une distance minimale de 1
mètre (3 pieds) des immeubles et d'autres équipements
pendant son fonctionnement. Ne placez pas d'objets
inflammables à côté du moteur.
3. Tenez les enfants et les animaux domestiques à l'écart de
la zone de travail; vous éviterez ainsi tout risque de
brûlures sur les pièces chaudes du moteur et de
blessures entraînées par les accessoires utilisés par le
moteur pour son fonctionnement.
4. Sachez comment arrêter rapidement le moteur, et
assurez-vous que vous avez bien compris le
fonctionnement de toutes les commandes. Ne permettez
jamais à une personne de faire fonctionner le moteur sans
connaître les instructions nécessaires.
5. L'essence est extrêmement inflammable et explosive dans
certaines conditions.
6. Remplissez le réservoir de carburant dans une zone bien
ventilée, moteur arrêté. Ne fumez pas et évitez toutes
flammes ou étincelles dans la zone de remplissage de
carburant ou dans une zone de stockage du carburant.
7. Veillez à ne pas faire déborder le réservoir de carburant.
Après remplissage, assurez-vous que le bouchon du
réservoir est solidement vissé.
8. Faites attention à ne pas renverser de carburant lors du
remplissage du réservoir. Les vapeurs ou les
éclaboussures de carburant peuvent s'enflammer. En cas
d'éclaboussures, assurez-vous que la zone est bien sèche
avant de faire démarrer le moteur.
9. Ne faites jamais fonctionner le moteur dans un endroit
fermé ou confiné. Les fumées d'échappement
contiennent du monoxyde de carbone qui est un gaz
toxique; une exposition prolongée peut entraîner une
perte de conscience et peut s'avérer mortelle.
10. Le silencieux devient très chaud pendant le
fonctionnement et reste chaud quelque temps après l’arrêt
du moteur. Faites attention à ne pas toucher le silencieux
tant qu'il est chaud. Pour éviter des brûlures graves ou
des risques d'incendie, laissez le moteur refroidir avant de
le transporter ou de le ranger à l'intérieur.
11. Ne transportez jamais le moteur si le réservoir est plein.
AVERTISSEMENT
Français
20 © SprayTECH. Todos los derechos reservados.
Precauciones de seguridad
Este manual contiene información que debe leer y comprender
antes de usar el equipo. Cuando se encuentre con uno de los
siguientes símbolos, asegúrese de observar sus indicaciones
de seguridad.
Este símbolo indica la existencia de un peligro potencial que
puede causar lesiones graves o la muerte. Después del
mismo se incluye información de seguridad importante.
Este símbolo indica la existencia de un peligro potencial para
usted o el equipo. Después del mismo se incluye información
importante que indica la forma de evitar daños al equipo o la
forma de prevenir lesiones menores.
INSTRUCCIONES DE SEGURIDAD IMPORTANTES
A.
GUARDE ESTAS INSTRUCCIONES – Para reducir el
riesgo de incendio o explosión, descarga eléctrica y
daños a las personas, lea y comprenda todas las
instrucciones incluidas en este manual. Familiarícese
con los controles y con el uso adecuado del equipo.
B. ADVERTENCIA – Para reducir el riesgo de incendio o
explosión:
1. No pulverice materiales inflamables ni combustibles
cerca de llamas desnudas, pilotos o fuentes de ignición
como objetos calientes, cigarrillos, motores, equipos
eléctricos o electrodomésticos. Evite producir chispas
al conectar y desconectar los cables de alimentación.
2. Para unidades que se vayan a utilizar con materiales
acuosos — No pulverice ni limpie con líquidos
inflamables. Para su uso con líquidos acuosos
solamente.
3. Para unidades que se vayan a utilizar solamente con
materiales acuosos o de tipo de alcohol mineral con un
punto de inflamación mínimo de 21 ºC (69,8 ºF) — No
pulverice ni limpie con líquidos que tengan un punto de
inflamación por debajo de 21 ºC (69,8 ºF). El punto de
inflamación es la temperatura a la que un fluido puede
producir vapor suficiente como para incendiarse.
4.
La pintura o disolvente que pase por el equipo puede
producir electricidad estática. La electricidad estática
supone un riesgo de incendio o explosión en presencia
de emanaciones de pintura o disolvente. Todas las
piezas del sistema pulverizador, incluyendo la bomba,
el conjunto de mangueras, la pistola pulverizadora y los
objetos dentro y alrededor de la zona de pulverización
se conectarán a tierra para protegerlos frente a
descargas estáticas y chispas. Utilice solamente
mangueras para pulverizadores de pintura airless (sin
aire) de alta presión conductoras o con toma a tierra
especificadas por el fabricante.
5. Compruebe que todos los recipientes y sistemas de
recogida están conectados a tierra para evitar
descargas eléctricas.
6. Conecte a una salida con toma a tierra y utilice cables
alargadores puestos a tierra. No utilice un adaptador de
3 a 2.
7. No utilice pintura o disolvente que contenga
hidrocarburos halogenados, como cloro, fungicida
blanqueador, cloruro de metileno y tricloroetano. No
son compatibles con el aluminio. Póngase en contacto
con el proveedor del material para conocer su
compatibilidad con el aluminio.
ADVERTENCIA
NOTA: los avisos contienen información importante,
présteles especial atención.
PRECAUCION
ADVERTENCIA
8. Mantenga la zona de pulverización bien ventilada.
Asegúrese de que circula aire fresco por la zona para
evitar que se acumulen vapores inflamables en el aire
de la zona de pulverización. Ponga el conjunto de la
bomba en una zona bien ventilada. No pulverice el
conjunto de la bomba.
9. No fume en la zona de pulverización.
10. No encienda interruptores de luces, motores ni
productos similares que puedan producir chispas en la
zona de pulverización.
11. Mantenga la zona limpia y despejada de botes de pintura
y disolventes, trapos y otros materiales inflamables.
12. Infórmese del contenido de la pintura y de los
disolventes que pulverice. Lea las hojas de datos sobre
seguridad de los materiales (MSDS) y las etiquetas en
los botes de pintura y disolvente. Siga las instrucciones
de seguridad del fabricante de la pintura y del disolvente.
13. Coloque la bomba al menos a 7,62 metros (25 pies) del
objeto que se va a pulverizar en una zona bien
ventilada (añada más manguera si fuera necesario).
Los vapores inflamables suelen ser más pesados que
el aire. La zona del suelo debe estar muy bien
ventilada. La bomba contiene piezas que forman arcos
que producen chispas y pueden inflamar los vapores.
14. El plástico puede producir chispas estáticas. Nunca
utilice plástico para cercar la zona de pulverización. No
utilice cortinas de plástico mientras pulveriza material
inflamable.
15. Deberá contar con equipos extintores de incendios que
funcionen correctamente.
C. ADVERTENCIA – Para reducir el riesgo de daños en la
piel:
1. No apunte con la pistola ni pulverice sobre ninguna
persona ni animal.
2. Mantenga las manos y el resto del cuerpo lejos de la
descarga. Por ejemplo, no trate de detener fugas con
ninguna parte de su cuerpo.
3.
Utilice siempre el protector de la boquilla. No pulverice
sin el protector en su sitio.
4. Utilice solamente la boquilla especificada por el
fabricante.
5. Tenga cuidado al limpiar y cambiar las boquillas. Si la
boquilla se atasca durante la pulverización,
ponga SIEMPRE el seguro del gatillo de la pistola,
apague la bomba y libere toda la presión antes de
reparar, limpiar el protector o la boquilla o cambiar la
boquilla. La presión no se libera apagando el motor.
Para liberar la presión hay que poner la manija de la
válvula PRIME/SPRAY (cebar/pulverizar) en PRIME.
Consulte el Procedimiento para liberar presión que se
describe en el manual de la bomba.
6. No deje el aparato con corriente ni con presión cuando
nadie esté pendiente de ella. Cuando no utilice el
aparato, apáguelo y libere la presión siguiendo las
instrucciones del fabricante.
7. La pulverización a alta presión puede inyectar toxinas en
el cuerpo y producir daños graves en el mismo. En caso
de que esto ocurra, visite a un médico inmediatamente.
8. Compruebe las mangueras y las piezas en busca de
daños; una fuga puede inyectar material en la piel.
Inspeccione la manguera antes de cada uso. Sustituya
las mangueras o las piezas dañadas.
PELIGRO:
Lesión causada por inyección. La corriente de líquido a
alta presión que produce este equipo puede perforar la
piel y tejidos subcutáneos, pudiendo provocar graves
lesiones y posibles amputaciones. Visite a un médico
inmediatamente. NO TRATE UNA LESIÓN CAUSADA
POR INYECCIÓN COMO UN SIMPLE CORTE.
ADVERTENCIA
Español
© SprayTECH. Todos los derechos reservados. 21
9. Este sistema es capaz de producir 3300 PSI / 22.8
MPa. Utilice solamente piezas de repuesto o
accesorios especificados por el fabricante y con una
capacidad nominal de 3300 PSI como mínimo. Entre
ellos se incluyen boquillas pulverizadoras, protectores
para las boquillas, pistolas, alargadores, racores y
mangueras.
10. Ponga siempre el seguro del gatillo cuando no esté
pulverizando. Verifique que el seguro del gatillo
funciona correctamente.
11. Antes de utilizar el aparato, verifique que todas las
conexiones son seguras.
12. Aprenda a detener el aparato y a liberar la presión
rápidamente. Familiarícese a conciencia con los
controles. La presión no se libera apagando el motor.
Para liberar la presión hay que poner la manija de la
válvula PRIME/SPRAY (cebar/pulverizar) en PRIME.
Consulte el Procedimiento para liberar presión que se
describe en el manual de la bomba.
13. Quite siempre la boquilla pulverizadora antes de
enjuagar o limpiar el sistema.
D. ADVERTENCIA – Para reducir el riesgo de lesiones:
1. Cuando pinte, lleve siempre guantes, protección para
los ojos, ropa y un respirador o máscara adecuados.
Vapores peligrosos: Las pinturas, disolventes,
insecticidas y otros materiales pueden ser perjudiciales
si se inhalan o entran en contacto con el cuerpo. Los
vapores pueden producir nauseas intensas, desmayos
o envenenamiento.
2. Nunca utilice el aparato ni pulverice cerca de niños.
Mantenga el equipo alejado de los niños en todo
momento.
3. No se estire demasiado ni se apoye sobre un soporte
inestable. Mantenga los pies bien apoyados y el
equilibrio en todo momento.
4.
No se distraiga y tenga cuidado con lo que hace.
5. No utilice el aparato si está fatigado o se encuentra
bajo la influencia del alcohol o de las drogas.
6. No retuerza ni doble la manguera en exceso. En la
manguera airless pueden aparecer fugas a causa del
desgaste, de retorcimientos o de un mal uso. Una fuga
puede inyectar material en la piel.
7. No exponga la manguera a temperaturas o presiones
que superen las especificadas por el fabricante.
8. No utilice la manguera como elemento de fuerza para
tirar del equipo o levantarlo.
9. Utilice la presión más baja posible para enjuagar el
equipo.
10. Cumpla todos los reglamentos locales, estatales y
nacionales pertinentes relativos a ventilación,
prevención de incendios y funcionamiento.
11. Las normas sobre seguridad del gobierno de los
Estados Unidos se han adoptado al amparo de la Ley
de salud y seguridad ocupacional (OSHA). Deben
consultarse tres normas, particularmente la sección
1910 de las Normas generales y la sección 1926 de las
Normas sobre construcción.
12. Cada vez que vaya a utilizar el equipo, compruebe
antes todas las mangueras en busca de cortes, fugas,
abrasión o bultos en la cubierta. Compruebe el
movimiento de los acoplamientos y si están dañados.
Sustituya inmediatamente una manguera si descubre
alguna de estas anomalías. No repare nunca una
manguera de pintura. Sustitúyala por una manguera
conductora a alta presión.
13. No pulverice al aire libre si hace viento.
14. Desenchufe siempre el cable antes de trabajar en el
equipo.
ADVERTENCIA
Seguridad del motor de gasolina
El escape del motor de esta unidad contiene productos
químicos que el Estado de California reconoce que
causan cáncer, defectos congénitos u otros daños a la
reproducción.
1. Los motores Honda han sido diseñados para ofrecer un
servicio seguro y fiable, si son manejados de acuerdo con
las instrucciones. Lea y comprenda el Manual del
Propietario de Honda antes de hacer funcionar el motor.
Si no hace esto, podrían producirse lesiones personales o
daños en el equipo.
2. Para evitar riesgos de incendio y proporcionar una
ventilación adecuada, mantenga el motor como mínimo a
1 metro (tres pies) de edificios y de otros equipos durante
su funcionamiento. No coloque objetos inflamables cerca
del motor.
3. Los niños y los animales de compañía deben mantenerse
alejados del área de trabajo, debido a la posibilidad de
quemaduras producidas por los componentes calientes
del motor o de daños producidos por el equipo al que
haga funcionar el motor.
4. Conozca el modo de detener rápidamente el motor, y
entienda el funcionamiento de todos los controles. No
permita que nadie haga funcionar el motor sin las
instrucciones adecuadas.
5. La gasolina es extremadamente inflamable y es explosiva
en determinadas circunstancias.
6. Reabastézcase de combustible en una zona bien
ventilada y con el motor apagado. No fume ni permita
que haya llamas ni chispas en el área de
reabastecimiento de combustible ni donde se almacene la
gasolina.
7. No llene excesivamente el tanque de combustible. Tras
repostar, asegúrese de que la tapa del tanque está
adecuadamente cerrada y asegurada.
8. Tenga cuidado de no derramar combustible cuando
realice el reabastecimiento. Los vapores del combustible
o el combustible derramado pueden inflamarse. Si se
derrama combustible, asegúrese de que el área esté seca
antes de arrancar el motor.
9. Nunca haga funcionar el motor en un área cerrada o
reducida. Los gases de escape contienen monóxido de
carbono tóxico: su exposición puede causar la pérdida del
conocimiento y puede originar la muerte.
10. El silenciador se calienta mucho durante el
funcionamiento y permanece caliente durante un tiempo
después de que el motor esté parado. Tenga cuidado de
no tocar el silenciador mientras está caliente. Para evitar
quemaduras graves o riesgos de incendio, deje que el
motor se enfríe antes de transportarlo o almacenarlo en el
interior.
11. Nunca transporte una unidad con gasolina en el tanque.
ADVERTENCIA
Español
22 © SprayTECH. All rights reserved.
Parts List
Main Assembly
8
11
10
9
12
13
16
14
15
7
3
4
5
6
1
2
17
18
19
20
21
22
24
23
25
Item Part # Description Quantity
1 0509550 Hex screw...................................................4
2 ---------- Engine.........................................................1
3 ---------- Drive assembly ...........................................1
4 0509627 Control cover ..............................................1
5 0509635 Screw..........................................................1
6 0509634 Port plug .....................................................1
7 0509924 Front cover..................................................1
8 0509552 Screw..........................................................4
9 0507768 Retaining ring..............................................1
10 0507777 Conecting pin..............................................1
11 0509636 Plug, nylon..................................................2
12 0555209 Fluid section assembly ...............................1
13 0509633 Socket screw ..............................................2
Item
Part # Description Quantity
14 0509543 Siphon tube.................................................1
15 0507738 Hose clip.....................................................1
16 5006536 Inlet screen .................................................1
17 ---------- Filter assembly............................................1
18 5000527 Fitting, 3/8”..................................................1
19 ---------- Cart assembly.............................................1
20 0509551 Lock nut ......................................................4
21 0507786 Lock washer................................................2
22 0507787 Hex screw...................................................2
23 0555205 Wire harness...............................................1
24 0509553 Screw..........................................................2
25 0509928 Grounding cable .........................................1
26 0507785 Return hose (not shown) ............................1
© SprayTECH. All rights reserved. 23
Item Part # Description Quantity
1 9850936 ON/OFF switch ...........................................1
2 0509558 Electronic pressure control assembly.........1
3 0509556 Screw..........................................................4
4 0507973 Potentiometer .............................................1
5 9800340 Ground screw .............................................1
6 9822113 Lock washer................................................1
7 0509605 Retaining ring..............................................1
8 0509604 Thrust washer.............................................1
9 0509495 Gasket ........................................................1
10 0555202 Pump housing assembly
(includes item 15) .......................................1
11 0509541 Lock washer................................................4
12 0509539 Socket screw, 2.25” ....................................2
13 0509540 Socket screw, 2” .........................................2
14 0555207 Slider assembly ..........................................1
15 0509644 Bronze bearing ...........................................1
16 0509610 Clutch rotor .................................................1
17 0509609 Drive shaft assembly ..................................1
18 0509612 Clutch field assembly..................................1
19 0507748 Cap .............................................................1
20 0507740 Pressure control knob.................................1
21 0509574 Plug.............................................................1
22 0507749 Seal nut.......................................................1
23 0509557 Mounting plate ............................................1
24 0507784 Grommet, 7/16”...........................................1
25 0509531 Grommet, liquid tight ..................................1
Item
Part # Description Quantity
26 0509646 Bearing .......................................................1
27 0555203 Gear housing
(includes items 26, 30, and 31 ...................1
28 0509614 Set screw, cone point .................................4
29 0509613 Set screw, cup point ...................................4
30 0509647 Grease seal ................................................1
31 0509645 Retaining ring..............................................1
32 0509603 Thrust washer, 1/2”.....................................1
33 0509606 Output gear assembly ................................1
34 0509599 Thrust washer, 5/8”.....................................1
35 0509607 Crankshaft assembly ..................................1
36 0509600 Thrust washer.............................................1
37 0509538 Screw..........................................................4
38 0555639 Clutch housing............................................1
39 0509611 Clutch armature assembly
(includes items 40, and 41(2))....................1
40 0509571 Taper lock bushing (includes item 41(2))....1
41 0509573 Set screw....................................................2
42 0509638 Socket screw ..............................................3
43 0509637 Lock washer................................................3
44 0555613 Engine, 4.5 HP ...........................................1
45 0509615 Hex screw...................................................4
46 0507786 Lock washer................................................4
NOTE: All electrical work should be performed by a
SprayTECH authorized service center.
Drive Assembly
44
3
1
4
9
10
11
13
12
14
15
8
7
5
6
2
39
40
41
42
43
45
46
19
20
22
23
24
34
35
36
32
26
31
33
29
30
28
27
38
37
25
18
21
17
16
24 © SprayTECH. All rights reserved.
Fluid Section Assembly (P/N 0555209)
1
2
3
7
8
12
13
14
15
9
18
16
17
19
20
21
10
11
4
5
6
22
Install lower packing with
large beveled edge
facing up.
Install upper packing
with raised lip
facing down.
Raised Lip
Large Beveled Edge
Item Part # Description Quantity
1 0508664 Retainer nut ................................................1
2 0508665 Piston guide................................................1
3 0509125 Upper packing assembly ............................1
4 0295559 Elbow, 90º...................................................1
5 0509595 Fitting..........................................................1
6 0509585 Gasket ........................................................1
7 0509578 Fluid Section Housing.................................1
8 0509593 Lower packing assembly ............................1
9 0551537 Piston..........................................................1
10 0551258 Outlet cage .................................................1
11 0551259 Crush washer..............................................1
12 50164 Outlet valve ball ..........................................1
13 0507407 Outlet valve seat.........................................1
14 13481 Outlet valve retainer ...................................1
15 0509590 Piston bushing ............................................1
16 0508677 Inlet cage ....................................................1
17 0508678 Inlet valve ball.............................................1
18 0509739 Inlet valve seal............................................1
19 0551534 Inlet valve seat............................................1
20 0509582 O-ring, PTFE ..............................................1
21 0509593 Inlet valve housing......................................1
22 0551536 Piston assembly
(includes items 9–14) .................................1
0509909 Repacking kit (includes items 2, 3, 6, 8,
12, 17, 18, and 20)
0509929 Lower packing insertion tool
NOTE: When repacking the fluid section, make sure
the raised lip on the bottom of the lower
packing is fully outside the packing around
the piston rod after insertion of the piston rod.
© SprayTECH. All rights reserved. 25
Cart Assembly
Item Part # Description
Quantity
1 0507766 Handle (includes items 2–5, 11, and 12)....1
2 9841504 Snap button ................................................2
3 0295609 Handle washer............................................2
4 0295610 Roll pin........................................................2
5 0295607 Handle sleeve.............................................2
6 0555603 Strain relief..................................................2
7 0507784 Grommet.....................................................3
8 0509625 Axle cap......................................................2
9 0509626 Wheel spacer..............................................2
10 9885571 Plug.............................................................2
11 0509386 Lock washer................................................4
12 0295608 Screw..........................................................4
13 0555218 Cart (includes item 10) ...............................1
14 0509624 Wheel .........................................................2
11
12
13
14
8
2
3
4
5
7
6
9
10
1
Filter Assembly
Item Part # Description Quantity
1 0508723 Filter body...................................................1
2 0508602 Filter spring.................................................1
3 0508748 Filter, 60 mesh (standard)...........................1
0508451 Filter, 30 mesh (optional)
0508452 Filter, 100 mesh (optional)
4 0508603 Adapter .......................................................1
5 0508749 Filter support spring....................................1
6 0508725 O-ring, PTFE ..............................................1
7 0507737 Transducer..................................................1
8 0509420 Plug, 3/8” ....................................................1
9 5000527 Outlet fitting.................................................1
10 0295697 Plug, 1/4” ....................................................1
11 0507793 Fitting, 1/4”..................................................1
12 0555625 Filter housing ..............................................1
13 0507690 PRIME/SPRAY valve assembly..................1
1
2
3
4
5
7
10
11
8
9
6
12
13
26 © SprayTECH. All rights reserved.
PRIME/SPRAY Valve Assembly
(P/N 0507690)
Item
Part # Description Quantity
1 0507736 Dowel pin....................................................1
2 0507745 Gasket ........................................................1
3 5000529 O-ring, PTFE ..............................................1
4 0507741 O-ring, Viton................................................1
5 0507744 Valve housing .............................................1
6 0507746 Valve seat ...................................................1
7 0507743 Valve stem ..................................................1
8 5006547 O-ring, Viton................................................1
9 0507747 Spring .........................................................1
10 0507742 Valve retainer..............................................1
11 0507735 Cam base ...................................................1
12 5006543 Groove pin ..................................................1
13 0507662 Valve handle ...............................................1
1
2
3
4
5
6
7
8
9
10
11
12
13
5 Gallon Siphon Set (optional)
Item Part # Description Quantity
1 0507964 Return hose ................................................1
2 0509185 Siphon hose................................................1
3 5006536 Inlet screen .................................................1
4 0507783 Clamp .........................................................1
5 0509727 Swivel elbow...............................................1
6 0509760 Adapter .......................................................1
7 0509761 Hose clamp.................................................1
8 0509788 Clip..............................................................1
9 0509789 Spring .........................................................1
1
2
3
5
4
6
8
9
7
© SprayTECH. All rights reserved. 27
Accessories
Part No. Description
0550xxx Tip Assembly
0297078 Tip Guard (11/16”)
0297070 Tip Guard (7/8”)
0291004 Hose, Whip End, 3' x 3/16"
0291003 Hose, Whip End, 5’ x 3/16”
0291002 Hose, Wireless, 25’ x 1/4"
0291000 Hose, Wireless, 50’ x 1/4"
0093896 Hose Connector, 1/4” x 1/4”M
0088154 Pressure Gauge, 0–5000 PSI
0152308 9" Roller Cover, 3/8” Nap
0152307 9" Roller Cover, 1/2” Nap
0152309 9" Roller Cover, 3/4” Nap
0152310 9" Roller Cover, 1-1/4” Nap
0152235 12" Roller Cover, 1/2" Nap
0152236 12" Roller Cover, 3/8" Nap
0152237 12" Roller Cover, 3/4" Nap
0152238 12" Roller Cover, 1-1/4" Nap
0093930 Anti-Seize Compound
0152909 R-10 Telescoping Roller, 9", 3/8" Nap
0152900 R-10 Telescoping 12" Roller, 3/8" Nap
0296329 G-10 XL Four Finger Airless Spray Gun (no tip)
0296235 G-10 XL Four Finger Airless Spray Gun with
517 reversible tip
0296260 G-10 XL Two Finger Airless Spray Gun (no tip)
0296236 G-10 XL Two Finger Airless Spray Gun with
517 reversible tIp
0296326 G-10 XL Four Finger Spray Pack with 50’ x 1/4”
airless hose
0296327 G-10 XL Two Finger Spray Pack with 50” x 1/4”
airless hose
0296297 G-12 XL Airless Spray Gun with
517 reversible tIp
0296330 G-12 XL Spray Pack with 50’ x 1/4” airless hose
0296470 G-15 XL Airless Spray Gun with
517 Reversible TIp
0296328 G-15 XL Spray Pack with 50’ x 1/4” airless hose
0279920 Separating oil
0507958 Electrostatic discharge (ESD) wrist strap
9870307 Grease, 6 lb. can
Electrical Schematic
Labels
Part # Description
0555897 Logo label, front
0295840 Warning label, explosion
0295841 Warning label, injection
0295805 Shock hazard label
0509819 “No Oil” label
Potentiometer
Transducer
E.P.C. Board
Switch
Engine
0555205
Clutch
J2
J3
J4
J7
J6
J5
Clutch Clutch
Switch
White
28 © SprayTECH. All rights reserved.
Limited Warranty
SprayTECH, a division of Wagner Spray Tech Corporation ("SprayTECH"), warrants that at the time of delivery to the original
purchaser for use (“End User”), the equipment covered by this warranty is free from defects in material and workmanship. With
the exception of any special, limited, or extended warranty published by SprayTECH, SprayTECH ’s obligation under this
warranty is limited to replacing or repairing without charge those parts which, to SprayTECH ’s reasonable satisfaction, are shown
to be defective within twelve (12) months after sale to the End User. This warranty applies only when the unit is installed and
operated in accordance with the recommendations and instructions of SprayTECH.
This warranty does not apply in the case of damage or wear caused by abrasion, corrosion or misuse, negligence, accident,
faulty installation, substitution of non- SprayTECH component parts, or tampering with the unit in a manner to impair normal
operation.
Defective parts are to be returned to an authorized SprayTECH sales/service outlet. All transportation charges, including return
to the factory, if necessary, are to be borne and prepaid by the End User. Repaired or replaced equipment will be returned to the
End User transportation prepaid.
THERE IS NO OTHER EXPRESS WARRANTY. SPRAYTECH HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES
INCLUDING, BUT NOT LIMITED TO, THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, TO
THE EXTENT PERMITTED BY LAW. THE DURATION OF ANY IMPLIED WARRANTIES WHICH CANNOT BE DISCLAIMED IS
LIMITED TO THE TIME PERIOD SPECIFIED IN THE EXPRESS WARRANTY. IN NO CASE SHALL SPRAYTECH LIABILITY
EXCEED THE AMOUNT OF THE PURCHASE PRICE. LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL
DAMAGES UNDER ANY AND ALL WARRANTIES IS EXCLUDED TO THE EXTENT PERMITTED BY LAW.
SPRAYTECH MAKES NO WARRANTY AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE WITH RESPECT TO ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD
BUT NOT MANUFACTURED BY SPRAYTECH. THOSE ITEMS SOLD, BUT NOT MANUFACTURED BY SPRAYTECH (SUCH
AS GAS ENGINES, SWITCHES, HOSES, ETC.) ARE SUBJECT TO THE WARRANTY, IF ANY, OF THEIR MANUFACTURER.
SPRAYTECH WILL PROVIDE THE PURCHASER WITH REASONABLE ASSISTANCE IN MAKING ANY CLAIM FOR BREACH
OF THESE WARRANTIES.
Material Safety Data Sheets (MSDS) are available on SprayTECH’s website or by calling Technical Service.
SprayTECH
1770 Fernbrook Lane
Minneapolis, MN 55447
Technical Assistance: 1-800-292-4637
Order Entry: 1-800-443-4500
Fax: 1-800-525-9501
www.spraytechinc.com
Patents
These products are covered by one or more of the following U.S. patents:
6,031,352 5,848,566 5,769,321 5,725,364 5,671,656 5,435,697 5,228,842
5,346,037 5,252,210 5,217,238 5,192,425 4,908,538 4,768,929 4,744,571
D384,676 6,179,222 5,934,883 4,723,892
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
Titan GPX80 El manual del propietario
- Categoría
- Rociador de pintura
- Tipo
- El manual del propietario
En otros idiomas
- français: Titan GPX80 Le manuel du propriétaire
- English: Titan GPX80 Owner's manual
Documentos relacionados
-
Titan GPX1600 El manual del propietario
-
-
Titan GPX85 El manual del propietario
-
SprayTECH EPX2355 El manual del propietario
-
-
-
SprayTECH EP2510 El manual del propietario
-
-
-
