Modern Forms PD-92818 Padron Instrucciones de operación

Modern Forms
Marca
Modern Forms
Modelo
PD-92818 Padron
Tipo
Instrucciones de operación
1
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company’s continuous improvement program.
INSTALLATION INSTRUCTION
928 – LED PENDANT
PD-92818
HARDWARE
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended to be installed by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Place the main power switch in the “OFF” position and remove the fuse(s) or switch “OFF” the circuit breakers which control the power
to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
Wire Connector
Qty: 4pcs+1 Extra
7EAC112201
Junction Box Screw
Qty: 2pcs+1 Extra
7MPF0820C1
#8-32x13/16
Mounting Screw
Qty: 1 Extra
7MPF0308S1
1/8”-10X6/16
Nickel Plating
A B C
G0
2
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company’s continuous improvement program.
INSTALLATION INSTRUCTION
928 – LED PENDANT
PD-92818
PREPARATION
1. Shut o the power at the circuit breaker and remove
existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the
parts on a clear area. Be careful not to lose any small
parts necessary for installation.
CONNECTING THE WIRES (Fig. 1)
3. Remove the mounting screw (C) from the xture.
4. Adjust the xture wire length by pushing the cable
gripper on the canopy and pulling the wire as desired.
5. Connect the driver input wires with junction box wires
as shown in Fig.2, making sure that all wire connectors
(A) are secured. If your outlet box has a green or bare
copper ground wire, connect the xture’s ground wire
to it. Otherwise, connect the xture’s ground wire
directly to the mounting plate using the green screw
provided. After wires are connected, tuck them carefully
inside the junction box
*Requires Driver to be recessed within the junction
box
MOUNTING THE FIXTURE (Fig. 2)
6. Secure mounting plate to the junction box using
junction box screws (B).The side of the mounting plate
marked “GND” must face out.
7. Connect the driver output wires with junction box wires
as shown in Fig.2, making sure that all wire connectors
(A) are secured.
8. Place the xture over the mounting plate and secure it
with mounting screws (C) .
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 1 Wiring
FIG. 2
BACK PLATE DIMENSIONS
G0
Junction Box
Wire Connector
Mounting Plate
Cable-gripper Push Up
Fixture
Junction Box Screw
Mounting Screw
Ground Wire
Driver 2 7/8”[L]x1 3/8”[W]x1 1/8”[H]
A
B
C
dka
1 3/4” 1 3/8”
Ø4 6/8”
7MBC120803
  • Page 1 1
  • Page 2 2

Modern Forms PD-92818 Padron Instrucciones de operación

Modern Forms
Marca
Modern Forms
Modelo
PD-92818 Padron
Tipo
Instrucciones de operación
Descargar PDF
informe

En otros idiomas

Documentos relacionados

Otros documentos